STARFIRE/DURALAN NETWORK DRIVER
M: Ion Badulescu <ionut@badula.org>
S: Odd Fixes
-F: drivers/net/starfire*
+F: drivers/net/ethernet/adaptec/starfire*
SUN3/3X
M: Sam Creasey <sammy@sammy.net>
will be asked for your specific card in the following questions. If
you are unsure, say Y.
-config ADAPTEC_STARFIRE
- tristate "Adaptec Starfire/DuraLAN support"
- depends on NET_PCI && PCI
- select CRC32
- select MII
- help
- Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
- adapter. The DuraLAN chip is used on the 64 bit PCI boards from
- Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
- driver.
-
- To compile this driver as a module, choose M here: the module
- will be called starfire. This is recommended.
-
config NET_POCKET
bool "Pocket and portable adapters"
depends on PARPORT
obj-$(CONFIG_ROADRUNNER) += rrunner.o
obj-$(CONFIG_SKFP) += skfp/
-obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
obj-$(CONFIG_RIONET) += rionet.o
obj-$(CONFIG_SH_ETH) += sh_eth.o
if ETHERNET
source "drivers/net/ethernet/3com/Kconfig"
+source "drivers/net/ethernet/adaptec/Kconfig"
source "drivers/net/ethernet/amd/Kconfig"
source "drivers/net/ethernet/apple/Kconfig"
source "drivers/net/ethernet/atheros/Kconfig"
obj-$(CONFIG_NET_VENDOR_3COM) += 3com/
obj-$(CONFIG_NET_VENDOR_8390) += 8390/
+obj-$(CONFIG_NET_VENDOR_ADAPTEC) += adaptec/
obj-$(CONFIG_NET_VENDOR_AMD) += amd/
obj-$(CONFIG_NET_VENDOR_APPLE) += apple/
obj-$(CONFIG_NET_VENDOR_ATHEROS) += atheros/
--- /dev/null
+#
+# Adaptec network device configuration
+#
+
+config NET_VENDOR_ADAPTEC
+ bool "Adaptec devices"
+ depends on PCI
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Adaptec cards. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_ADAPTEC
+
+config ADAPTEC_STARFIRE
+ tristate "Adaptec Starfire/DuraLAN support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
+ adapter. The DuraLAN chip is used on the 64 bit PCI boards from
+ Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
+ driver.
+
+ To compile this driver as a module, choose M here: the module
+ will be called starfire. This is recommended.
+
+endif # NET_VENDOR_ADAPTEC
--- /dev/null
+#
+# Makefile for the Adaptec network device drivers.
+#
+
+obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
--- /dev/null
+/* starfire.c: Linux device driver for the Adaptec Starfire network adapter. */
+/*
+ Written 1998-2000 by Donald Becker.
+
+ Current maintainer is Ion Badulescu <ionut ta badula tod org>. Please
+ send all bug reports to me, and not to Donald Becker, as this code
+ has been heavily modified from Donald's original version.
+
+ This software may be used and distributed according to the terms of
+ the GNU General Public License (GPL), incorporated herein by reference.
+ Drivers based on or derived from this code fall under the GPL and must
+ retain the authorship, copyright and license notice. This file is not
+ a complete program and may only be used when the entire operating
+ system is licensed under the GPL.
+
+ The information below comes from Donald Becker's original driver:
+
+ The author may be reached as becker@scyld.com, or C/O
+ Scyld Computing Corporation
+ 410 Severn Ave., Suite 210
+ Annapolis MD 21403
+
+ Support and updates available at
+ http://www.scyld.com/network/starfire.html
+ [link no longer provides useful info -jgarzik]
+
+*/
+
+#define DRV_NAME "starfire"
+#define DRV_VERSION "2.1"
+#define DRV_RELDATE "July 6, 2008"
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/crc32.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/if_vlan.h>
+#include <linux/mm.h>
+#include <linux/firmware.h>
+#include <asm/processor.h> /* Processor type for cache alignment. */
+#include <asm/uaccess.h>
+#include <asm/io.h>
+
+/*
+ * The current frame processor firmware fails to checksum a fragment
+ * of length 1. If and when this is fixed, the #define below can be removed.
+ */
+#define HAS_BROKEN_FIRMWARE
+
+/*
+ * If using the broken firmware, data must be padded to the next 32-bit boundary.
+ */
+#ifdef HAS_BROKEN_FIRMWARE
+#define PADDING_MASK 3
+#endif
+
+/*
+ * Define this if using the driver with the zero-copy patch
+ */
+#define ZEROCOPY
+
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#define VLAN_SUPPORT
+#endif
+
+/* The user-configurable values.
+ These may be modified when a driver module is loaded.*/
+
+/* Used for tuning interrupt latency vs. overhead. */
+static int intr_latency;
+static int small_frames;
+
+static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */
+static int max_interrupt_work = 20;
+static int mtu;
+/* Maximum number of multicast addresses to filter (vs. rx-all-multicast).
+ The Starfire has a 512 element hash table based on the Ethernet CRC. */
+static const int multicast_filter_limit = 512;
+/* Whether to do TCP/UDP checksums in hardware */
+static int enable_hw_cksum = 1;
+
+#define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
+/*
+ * Set the copy breakpoint for the copy-only-tiny-frames scheme.
+ * Setting to > 1518 effectively disables this feature.
+ *
+ * NOTE:
+ * The ia64 doesn't allow for unaligned loads even of integers being
+ * misaligned on a 2 byte boundary. Thus always force copying of
+ * packets as the starfire doesn't allow for misaligned DMAs ;-(
+ * 23/10/2000 - Jes
+ *
+ * The Alpha and the Sparc don't like unaligned loads, either. On Sparc64,
+ * at least, having unaligned frames leads to a rather serious performance
+ * penalty. -Ion
+ */
+#if defined(__ia64__) || defined(__alpha__) || defined(__sparc__)
+static int rx_copybreak = PKT_BUF_SZ;
+#else
+static int rx_copybreak /* = 0 */;
+#endif
+
+/* PCI DMA burst size -- on sparc64 we want to force it to 64 bytes, on the others the default of 128 is fine. */
+#ifdef __sparc__
+#define DMA_BURST_SIZE 64
+#else
+#define DMA_BURST_SIZE 128
+#endif
+
+/* Used to pass the media type, etc.
+ Both 'options[]' and 'full_duplex[]' exist for driver interoperability.
+ The media type is usually passed in 'options[]'.
+ These variables are deprecated, use ethtool instead. -Ion
+*/
+#define MAX_UNITS 8 /* More are supported, limit only on options */
+static int options[MAX_UNITS] = {0, };
+static int full_duplex[MAX_UNITS] = {0, };
+
+/* Operational parameters that are set at compile time. */
+
+/* The "native" ring sizes are either 256 or 2048.
+ However in some modes a descriptor may be marked to wrap the ring earlier.
+*/
+#define RX_RING_SIZE 256
+#define TX_RING_SIZE 32
+/* The completion queues are fixed at 1024 entries i.e. 4K or 8KB. */
+#define DONE_Q_SIZE 1024
+/* All queues must be aligned on a 256-byte boundary */
+#define QUEUE_ALIGN 256
+
+#if RX_RING_SIZE > 256
+#define RX_Q_ENTRIES Rx2048QEntries
+#else
+#define RX_Q_ENTRIES Rx256QEntries
+#endif
+
+/* Operational parameters that usually are not changed. */
+/* Time in jiffies before concluding the transmitter is hung. */
+#define TX_TIMEOUT (2 * HZ)
+
+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
+/* 64-bit dma_addr_t */
+#define ADDR_64BITS /* This chip uses 64 bit addresses. */
+#define netdrv_addr_t __le64
+#define cpu_to_dma(x) cpu_to_le64(x)
+#define dma_to_cpu(x) le64_to_cpu(x)
+#define RX_DESC_Q_ADDR_SIZE RxDescQAddr64bit
+#define TX_DESC_Q_ADDR_SIZE TxDescQAddr64bit
+#define RX_COMPL_Q_ADDR_SIZE RxComplQAddr64bit
+#define TX_COMPL_Q_ADDR_SIZE TxComplQAddr64bit
+#define RX_DESC_ADDR_SIZE RxDescAddr64bit
+#else /* 32-bit dma_addr_t */
+#define netdrv_addr_t __le32
+#define cpu_to_dma(x) cpu_to_le32(x)
+#define dma_to_cpu(x) le32_to_cpu(x)
+#define RX_DESC_Q_ADDR_SIZE RxDescQAddr32bit
+#define TX_DESC_Q_ADDR_SIZE TxDescQAddr32bit
+#define RX_COMPL_Q_ADDR_SIZE RxComplQAddr32bit
+#define TX_COMPL_Q_ADDR_SIZE TxComplQAddr32bit
+#define RX_DESC_ADDR_SIZE RxDescAddr32bit
+#endif
+
+#define skb_first_frag_len(skb) skb_headlen(skb)
+#define skb_num_frags(skb) (skb_shinfo(skb)->nr_frags + 1)
+
+/* Firmware names */
+#define FIRMWARE_RX "adaptec/starfire_rx.bin"
+#define FIRMWARE_TX "adaptec/starfire_tx.bin"
+
+/* These identify the driver base version and may not be removed. */
+static const char version[] __devinitconst =
+KERN_INFO "starfire.c:v1.03 7/26/2000 Written by Donald Becker <becker@scyld.com>\n"
+" (unofficial 2.2/2.4 kernel port, version " DRV_VERSION ", " DRV_RELDATE ")\n";
+
+MODULE_AUTHOR("Donald Becker <becker@scyld.com>");
+MODULE_DESCRIPTION("Adaptec Starfire Ethernet driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+MODULE_FIRMWARE(FIRMWARE_RX);
+MODULE_FIRMWARE(FIRMWARE_TX);
+
+module_param(max_interrupt_work, int, 0);
+module_param(mtu, int, 0);
+module_param(debug, int, 0);
+module_param(rx_copybreak, int, 0);
+module_param(intr_latency, int, 0);
+module_param(small_frames, int, 0);
+module_param_array(options, int, NULL, 0);
+module_param_array(full_duplex, int, NULL, 0);
+module_param(enable_hw_cksum, int, 0);
+MODULE_PARM_DESC(max_interrupt_work, "Maximum events handled per interrupt");
+MODULE_PARM_DESC(mtu, "MTU (all boards)");
+MODULE_PARM_DESC(debug, "Debug level (0-6)");
+MODULE_PARM_DESC(rx_copybreak, "Copy breakpoint for copy-only-tiny-frames");
+MODULE_PARM_DESC(intr_latency, "Maximum interrupt latency, in microseconds");
+MODULE_PARM_DESC(small_frames, "Maximum size of receive frames that bypass interrupt latency (0,64,128,256,512)");
+MODULE_PARM_DESC(options, "Deprecated: Bits 0-3: media type, bit 17: full duplex");
+MODULE_PARM_DESC(full_duplex, "Deprecated: Forced full-duplex setting (0/1)");
+MODULE_PARM_DESC(enable_hw_cksum, "Enable/disable hardware cksum support (0/1)");
+
+/*
+ Theory of Operation
+
+I. Board Compatibility
+
+This driver is for the Adaptec 6915 "Starfire" 64 bit PCI Ethernet adapter.
+
+II. Board-specific settings
+
+III. Driver operation
+
+IIIa. Ring buffers
+
+The Starfire hardware uses multiple fixed-size descriptor queues/rings. The
+ring sizes are set fixed by the hardware, but may optionally be wrapped
+earlier by the END bit in the descriptor.
+This driver uses that hardware queue size for the Rx ring, where a large
+number of entries has no ill effect beyond increases the potential backlog.
+The Tx ring is wrapped with the END bit, since a large hardware Tx queue
+disables the queue layer priority ordering and we have no mechanism to
+utilize the hardware two-level priority queue. When modifying the
+RX/TX_RING_SIZE pay close attention to page sizes and the ring-empty warning
+levels.
+
+IIIb/c. Transmit/Receive Structure
+
+See the Adaptec manual for the many possible structures, and options for
+each structure. There are far too many to document all of them here.
+
+For transmit this driver uses type 0/1 transmit descriptors (depending
+on the 32/64 bitness of the architecture), and relies on automatic
+minimum-length padding. It does not use the completion queue
+consumer index, but instead checks for non-zero status entries.
+
+For receive this driver uses type 2/3 receive descriptors. The driver
+allocates full frame size skbuffs for the Rx ring buffers, so all frames
+should fit in a single descriptor. The driver does not use the completion
+queue consumer index, but instead checks for non-zero status entries.
+
+When an incoming frame is less than RX_COPYBREAK bytes long, a fresh skbuff
+is allocated and the frame is copied to the new skbuff. When the incoming
+frame is larger, the skbuff is passed directly up the protocol stack.
+Buffers consumed this way are replaced by newly allocated skbuffs in a later
+phase of receive.
+
+A notable aspect of operation is that unaligned buffers are not permitted by
+the Starfire hardware. Thus the IP header at offset 14 in an ethernet frame
+isn't longword aligned, which may cause problems on some machine
+e.g. Alphas and IA64. For these architectures, the driver is forced to copy
+the frame into a new skbuff unconditionally. Copied frames are put into the
+skbuff at an offset of "+2", thus 16-byte aligning the IP header.
+
+IIId. Synchronization
+
+The driver runs as two independent, single-threaded flows of control. One
+is the send-packet routine, which enforces single-threaded use by the
+dev->tbusy flag. The other thread is the interrupt handler, which is single
+threaded by the hardware and interrupt handling software.
+
+The send packet thread has partial control over the Tx ring and the netif_queue
+status. If the number of free Tx slots in the ring falls below a certain number
+(currently hardcoded to 4), it signals the upper layer to stop the queue.
+
+The interrupt handler has exclusive control over the Rx ring and records stats
+from the Tx ring. After reaping the stats, it marks the Tx queue entry as
+empty by incrementing the dirty_tx mark. Iff the netif_queue is stopped and the
+number of free Tx slow is above the threshold, it signals the upper layer to
+restart the queue.
+
+IV. Notes
+
+IVb. References
+
+The Adaptec Starfire manuals, available only from Adaptec.
+http://www.scyld.com/expert/100mbps.html
+http://www.scyld.com/expert/NWay.html
+
+IVc. Errata
+
+- StopOnPerr is broken, don't enable
+- Hardware ethernet padding exposes random data, perform software padding
+ instead (unverified -- works correctly for all the hardware I have)
+
+*/
+
+
+
+enum chip_capability_flags {CanHaveMII=1, };
+
+enum chipset {
+ CH_6915 = 0,
+};
+
+static DEFINE_PCI_DEVICE_TABLE(starfire_pci_tbl) = {
+ { PCI_VDEVICE(ADAPTEC, 0x6915), CH_6915 },
+ { 0, }
+};
+MODULE_DEVICE_TABLE(pci, starfire_pci_tbl);
+
+/* A chip capabilities table, matching the CH_xxx entries in xxx_pci_tbl[] above. */
+static const struct chip_info {
+ const char *name;
+ int drv_flags;
+} netdrv_tbl[] __devinitdata = {
+ { "Adaptec Starfire 6915", CanHaveMII },
+};
+
+
+/* Offsets to the device registers.
+ Unlike software-only systems, device drivers interact with complex hardware.
+ It's not useful to define symbolic names for every register bit in the
+ device. The name can only partially document the semantics and make
+ the driver longer and more difficult to read.
+ In general, only the important configuration values or bits changed
+ multiple times should be defined symbolically.
+*/
+enum register_offsets {
+ PCIDeviceConfig=0x50040, GenCtrl=0x50070, IntrTimerCtrl=0x50074,
+ IntrClear=0x50080, IntrStatus=0x50084, IntrEnable=0x50088,
+ MIICtrl=0x52000, TxStationAddr=0x50120, EEPROMCtrl=0x51000,
+ GPIOCtrl=0x5008C, TxDescCtrl=0x50090,
+ TxRingPtr=0x50098, HiPriTxRingPtr=0x50094, /* Low and High priority. */
+ TxRingHiAddr=0x5009C, /* 64 bit address extension. */
+ TxProducerIdx=0x500A0, TxConsumerIdx=0x500A4,
+ TxThreshold=0x500B0,
+ CompletionHiAddr=0x500B4, TxCompletionAddr=0x500B8,
+ RxCompletionAddr=0x500BC, RxCompletionQ2Addr=0x500C0,
+ CompletionQConsumerIdx=0x500C4, RxDMACtrl=0x500D0,
+ RxDescQCtrl=0x500D4, RxDescQHiAddr=0x500DC, RxDescQAddr=0x500E0,
+ RxDescQIdx=0x500E8, RxDMAStatus=0x500F0, RxFilterMode=0x500F4,
+ TxMode=0x55000, VlanType=0x55064,
+ PerfFilterTable=0x56000, HashTable=0x56100,
+ TxGfpMem=0x58000, RxGfpMem=0x5a000,
+};
+
+/*
+ * Bits in the interrupt status/mask registers.
+ * Warning: setting Intr[Ab]NormalSummary in the IntrEnable register
+ * enables all the interrupt sources that are or'ed into those status bits.
+ */
+enum intr_status_bits {
+ IntrLinkChange=0xf0000000, IntrStatsMax=0x08000000,
+ IntrAbnormalSummary=0x02000000, IntrGeneralTimer=0x01000000,
+ IntrSoftware=0x800000, IntrRxComplQ1Low=0x400000,
+ IntrTxComplQLow=0x200000, IntrPCI=0x100000,
+ IntrDMAErr=0x080000, IntrTxDataLow=0x040000,
+ IntrRxComplQ2Low=0x020000, IntrRxDescQ1Low=0x010000,
+ IntrNormalSummary=0x8000, IntrTxDone=0x4000,
+ IntrTxDMADone=0x2000, IntrTxEmpty=0x1000,
+ IntrEarlyRxQ2=0x0800, IntrEarlyRxQ1=0x0400,
+ IntrRxQ2Done=0x0200, IntrRxQ1Done=0x0100,
+ IntrRxGFPDead=0x80, IntrRxDescQ2Low=0x40,
+ IntrNoTxCsum=0x20, IntrTxBadID=0x10,
+ IntrHiPriTxBadID=0x08, IntrRxGfp=0x04,
+ IntrTxGfp=0x02, IntrPCIPad=0x01,
+ /* not quite bits */
+ IntrRxDone=IntrRxQ2Done | IntrRxQ1Done,
+ IntrRxEmpty=IntrRxDescQ1Low | IntrRxDescQ2Low,
+ IntrNormalMask=0xff00, IntrAbnormalMask=0x3ff00fe,
+};
+
+/* Bits in the RxFilterMode register. */
+enum rx_mode_bits {
+ AcceptBroadcast=0x04, AcceptAllMulticast=0x02, AcceptAll=0x01,
+ AcceptMulticast=0x10, PerfectFilter=0x40, HashFilter=0x30,
+ PerfectFilterVlan=0x80, MinVLANPrio=0xE000, VlanMode=0x0200,
+ WakeupOnGFP=0x0800,
+};
+
+/* Bits in the TxMode register */
+enum tx_mode_bits {
+ MiiSoftReset=0x8000, MIILoopback=0x4000,
+ TxFlowEnable=0x0800, RxFlowEnable=0x0400,
+ PadEnable=0x04, FullDuplex=0x02, HugeFrame=0x01,
+};
+
+/* Bits in the TxDescCtrl register. */
+enum tx_ctrl_bits {
+ TxDescSpaceUnlim=0x00, TxDescSpace32=0x10, TxDescSpace64=0x20,
+ TxDescSpace128=0x30, TxDescSpace256=0x40,
+ TxDescType0=0x00, TxDescType1=0x01, TxDescType2=0x02,
+ TxDescType3=0x03, TxDescType4=0x04,
+ TxNoDMACompletion=0x08,
+ TxDescQAddr64bit=0x80, TxDescQAddr32bit=0,
+ TxHiPriFIFOThreshShift=24, TxPadLenShift=16,
+ TxDMABurstSizeShift=8,
+};
+
+/* Bits in the RxDescQCtrl register. */
+enum rx_ctrl_bits {
+ RxBufferLenShift=16, RxMinDescrThreshShift=0,
+ RxPrefetchMode=0x8000, RxVariableQ=0x2000,
+ Rx2048QEntries=0x4000, Rx256QEntries=0,
+ RxDescAddr64bit=0x1000, RxDescAddr32bit=0,
+ RxDescQAddr64bit=0x0100, RxDescQAddr32bit=0,
+ RxDescSpace4=0x000, RxDescSpace8=0x100,
+ RxDescSpace16=0x200, RxDescSpace32=0x300,
+ RxDescSpace64=0x400, RxDescSpace128=0x500,
+ RxConsumerWrEn=0x80,
+};
+
+/* Bits in the RxDMACtrl register. */
+enum rx_dmactrl_bits {
+ RxReportBadFrames=0x80000000, RxDMAShortFrames=0x40000000,
+ RxDMABadFrames=0x20000000, RxDMACrcErrorFrames=0x10000000,
+ RxDMAControlFrame=0x08000000, RxDMAPauseFrame=0x04000000,
+ RxChecksumIgnore=0, RxChecksumRejectTCPUDP=0x02000000,
+ RxChecksumRejectTCPOnly=0x01000000,
+ RxCompletionQ2Enable=0x800000,
+ RxDMAQ2Disable=0, RxDMAQ2FPOnly=0x100000,
+ RxDMAQ2SmallPkt=0x200000, RxDMAQ2HighPrio=0x300000,
+ RxDMAQ2NonIP=0x400000,
+ RxUseBackupQueue=0x080000, RxDMACRC=0x040000,
+ RxEarlyIntThreshShift=12, RxHighPrioThreshShift=8,
+ RxBurstSizeShift=0,
+};
+
+/* Bits in the RxCompletionAddr register */
+enum rx_compl_bits {
+ RxComplQAddr64bit=0x80, RxComplQAddr32bit=0,
+ RxComplProducerWrEn=0x40,
+ RxComplType0=0x00, RxComplType1=0x10,
+ RxComplType2=0x20, RxComplType3=0x30,
+ RxComplThreshShift=0,
+};
+
+/* Bits in the TxCompletionAddr register */
+enum tx_compl_bits {
+ TxComplQAddr64bit=0x80, TxComplQAddr32bit=0,
+ TxComplProducerWrEn=0x40,
+ TxComplIntrStatus=0x20,
+ CommonQueueMode=0x10,
+ TxComplThreshShift=0,
+};
+
+/* Bits in the GenCtrl register */
+enum gen_ctrl_bits {
+ RxEnable=0x05, TxEnable=0x0a,
+ RxGFPEnable=0x10, TxGFPEnable=0x20,
+};
+
+/* Bits in the IntrTimerCtrl register */
+enum intr_ctrl_bits {
+ Timer10X=0x800, EnableIntrMasking=0x60, SmallFrameBypass=0x100,
+ SmallFrame64=0, SmallFrame128=0x200, SmallFrame256=0x400, SmallFrame512=0x600,
+ IntrLatencyMask=0x1f,
+};
+
+/* The Rx and Tx buffer descriptors. */
+struct starfire_rx_desc {
+ netdrv_addr_t rxaddr;
+};
+enum rx_desc_bits {
+ RxDescValid=1, RxDescEndRing=2,
+};
+
+/* Completion queue entry. */
+struct short_rx_done_desc {
+ __le32 status; /* Low 16 bits is length. */
+};
+struct basic_rx_done_desc {
+ __le32 status; /* Low 16 bits is length. */
+ __le16 vlanid;
+ __le16 status2;
+};
+struct csum_rx_done_desc {
+ __le32 status; /* Low 16 bits is length. */
+ __le16 csum; /* Partial checksum */
+ __le16 status2;
+};
+struct full_rx_done_desc {
+ __le32 status; /* Low 16 bits is length. */
+ __le16 status3;
+ __le16 status2;
+ __le16 vlanid;
+ __le16 csum; /* partial checksum */
+ __le32 timestamp;
+};
+/* XXX: this is ugly and I'm not sure it's worth the trouble -Ion */
+#ifdef VLAN_SUPPORT
+typedef struct full_rx_done_desc rx_done_desc;
+#define RxComplType RxComplType3
+#else /* not VLAN_SUPPORT */
+typedef struct csum_rx_done_desc rx_done_desc;
+#define RxComplType RxComplType2
+#endif /* not VLAN_SUPPORT */
+
+enum rx_done_bits {
+ RxOK=0x20000000, RxFIFOErr=0x10000000, RxBufQ2=0x08000000,
+};
+
+/* Type 1 Tx descriptor. */
+struct starfire_tx_desc_1 {
+ __le32 status; /* Upper bits are status, lower 16 length. */
+ __le32 addr;
+};
+
+/* Type 2 Tx descriptor. */
+struct starfire_tx_desc_2 {
+ __le32 status; /* Upper bits are status, lower 16 length. */
+ __le32 reserved;
+ __le64 addr;
+};
+
+#ifdef ADDR_64BITS
+typedef struct starfire_tx_desc_2 starfire_tx_desc;
+#define TX_DESC_TYPE TxDescType2
+#else /* not ADDR_64BITS */
+typedef struct starfire_tx_desc_1 starfire_tx_desc;
+#define TX_DESC_TYPE TxDescType1
+#endif /* not ADDR_64BITS */
+#define TX_DESC_SPACING TxDescSpaceUnlim
+
+enum tx_desc_bits {
+ TxDescID=0xB0000000,
+ TxCRCEn=0x01000000, TxDescIntr=0x08000000,
+ TxRingWrap=0x04000000, TxCalTCP=0x02000000,
+};
+struct tx_done_desc {
+ __le32 status; /* timestamp, index. */
+#if 0
+ __le32 intrstatus; /* interrupt status */
+#endif
+};
+
+struct rx_ring_info {
+ struct sk_buff *skb;
+ dma_addr_t mapping;
+};
+struct tx_ring_info {
+ struct sk_buff *skb;
+ dma_addr_t mapping;
+ unsigned int used_slots;
+};
+
+#define PHY_CNT 2
+struct netdev_private {
+ /* Descriptor rings first for alignment. */
+ struct starfire_rx_desc *rx_ring;
+ starfire_tx_desc *tx_ring;
+ dma_addr_t rx_ring_dma;
+ dma_addr_t tx_ring_dma;
+ /* The addresses of rx/tx-in-place skbuffs. */
+ struct rx_ring_info rx_info[RX_RING_SIZE];
+ struct tx_ring_info tx_info[TX_RING_SIZE];
+ /* Pointers to completion queues (full pages). */
+ rx_done_desc *rx_done_q;
+ dma_addr_t rx_done_q_dma;
+ unsigned int rx_done;
+ struct tx_done_desc *tx_done_q;
+ dma_addr_t tx_done_q_dma;
+ unsigned int tx_done;
+ struct napi_struct napi;
+ struct net_device *dev;
+ struct pci_dev *pci_dev;
+#ifdef VLAN_SUPPORT
+ unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)];
+#endif
+ void *queue_mem;
+ dma_addr_t queue_mem_dma;
+ size_t queue_mem_size;
+
+ /* Frequently used values: keep some adjacent for cache effect. */
+ spinlock_t lock;
+ unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
+ unsigned int cur_tx, dirty_tx, reap_tx;
+ unsigned int rx_buf_sz; /* Based on MTU+slack. */
+ /* These values keep track of the transceiver/media in use. */
+ int speed100; /* Set if speed == 100MBit. */
+ u32 tx_mode;
+ u32 intr_timer_ctrl;
+ u8 tx_threshold;
+ /* MII transceiver section. */
+ struct mii_if_info mii_if; /* MII lib hooks/info */
+ int phy_cnt; /* MII device addresses. */
+ unsigned char phys[PHY_CNT]; /* MII device addresses. */
+ void __iomem *base;
+};
+
+
+static int mdio_read(struct net_device *dev, int phy_id, int location);
+static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
+static int netdev_open(struct net_device *dev);
+static void check_duplex(struct net_device *dev);
+static void tx_timeout(struct net_device *dev);
+static void init_ring(struct net_device *dev);
+static netdev_tx_t start_tx(struct sk_buff *skb, struct net_device *dev);
+static irqreturn_t intr_handler(int irq, void *dev_instance);
+static void netdev_error(struct net_device *dev, int intr_status);
+static int __netdev_rx(struct net_device *dev, int *quota);
+static int netdev_poll(struct napi_struct *napi, int budget);
+static void refill_rx_ring(struct net_device *dev);
+static void netdev_error(struct net_device *dev, int intr_status);
+static void set_rx_mode(struct net_device *dev);
+static struct net_device_stats *get_stats(struct net_device *dev);
+static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
+static int netdev_close(struct net_device *dev);
+static void netdev_media_change(struct net_device *dev);
+static const struct ethtool_ops ethtool_ops;
+
+
+#ifdef VLAN_SUPPORT
+static void netdev_vlan_rx_add_vid(struct net_device *dev, unsigned short vid)
+{
+ struct netdev_private *np = netdev_priv(dev);
+
+ spin_lock(&np->lock);
+ if (debug > 1)
+ printk("%s: Adding vlanid %d to vlan filter\n", dev->name, vid);
+ set_bit(vid, np->active_vlans);
+ set_rx_mode(dev);
+ spin_unlock(&np->lock);
+}
+
+static void netdev_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
+{
+ struct netdev_private *np = netdev_priv(dev);
+
+ spin_lock(&np->lock);
+ if (debug > 1)
+ printk("%s: removing vlanid %d from vlan filter\n", dev->name, vid);
+ clear_bit(vid, np->active_vlans);
+ set_rx_mode(dev);
+ spin_unlock(&np->lock);
+}
+#endif /* VLAN_SUPPORT */
+
+
+static const struct net_device_ops netdev_ops = {
+ .ndo_open = netdev_open,
+ .ndo_stop = netdev_close,
+ .ndo_start_xmit = start_tx,
+ .ndo_tx_timeout = tx_timeout,
+ .ndo_get_stats = get_stats,
+ .ndo_set_multicast_list = &set_rx_mode,
+ .ndo_do_ioctl = netdev_ioctl,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+#ifdef VLAN_SUPPORT
+ .ndo_vlan_rx_add_vid = netdev_vlan_rx_add_vid,
+ .ndo_vlan_rx_kill_vid = netdev_vlan_rx_kill_vid,
+#endif
+};
+
+static int __devinit starfire_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct netdev_private *np;
+ int i, irq, option, chip_idx = ent->driver_data;
+ struct net_device *dev;
+ static int card_idx = -1;
+ long ioaddr;
+ void __iomem *base;
+ int drv_flags, io_size;
+ int boguscnt;
+
+/* when built into the kernel, we only print version if device is found */
+#ifndef MODULE
+ static int printed_version;
+ if (!printed_version++)
+ printk(version);
+#endif
+
+ card_idx++;
+
+ if (pci_enable_device (pdev))
+ return -EIO;
+
+ ioaddr = pci_resource_start(pdev, 0);
+ io_size = pci_resource_len(pdev, 0);
+ if (!ioaddr || ((pci_resource_flags(pdev, 0) & IORESOURCE_MEM) == 0)) {
+ printk(KERN_ERR DRV_NAME " %d: no PCI MEM resources, aborting\n", card_idx);
+ return -ENODEV;
+ }
+
+ dev = alloc_etherdev(sizeof(*np));
+ if (!dev) {
+ printk(KERN_ERR DRV_NAME " %d: cannot alloc etherdev, aborting\n", card_idx);
+ return -ENOMEM;
+ }
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ irq = pdev->irq;
+
+ if (pci_request_regions (pdev, DRV_NAME)) {
+ printk(KERN_ERR DRV_NAME " %d: cannot reserve PCI resources, aborting\n", card_idx);
+ goto err_out_free_netdev;
+ }
+
+ base = ioremap(ioaddr, io_size);
+ if (!base) {
+ printk(KERN_ERR DRV_NAME " %d: cannot remap %#x @ %#lx, aborting\n",
+ card_idx, io_size, ioaddr);
+ goto err_out_free_res;
+ }
+
+ pci_set_master(pdev);
+
+ /* enable MWI -- it vastly improves Rx performance on sparc64 */
+ pci_try_set_mwi(pdev);
+
+#ifdef ZEROCOPY
+ /* Starfire can do TCP/UDP checksumming */
+ if (enable_hw_cksum)
+ dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
+#endif /* ZEROCOPY */
+
+#ifdef VLAN_SUPPORT
+ dev->features |= NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER;
+#endif /* VLAN_RX_KILL_VID */
+#ifdef ADDR_64BITS
+ dev->features |= NETIF_F_HIGHDMA;
+#endif /* ADDR_64BITS */
+
+ /* Serial EEPROM reads are hidden by the hardware. */
+ for (i = 0; i < 6; i++)
+ dev->dev_addr[i] = readb(base + EEPROMCtrl + 20 - i);
+
+#if ! defined(final_version) /* Dump the EEPROM contents during development. */
+ if (debug > 4)
+ for (i = 0; i < 0x20; i++)
+ printk("%2.2x%s",
+ (unsigned int)readb(base + EEPROMCtrl + i),
+ i % 16 != 15 ? " " : "\n");
+#endif
+
+ /* Issue soft reset */
+ writel(MiiSoftReset, base + TxMode);
+ udelay(1000);
+ writel(0, base + TxMode);
+
+ /* Reset the chip to erase previous misconfiguration. */
+ writel(1, base + PCIDeviceConfig);
+ boguscnt = 1000;
+ while (--boguscnt > 0) {
+ udelay(10);
+ if ((readl(base + PCIDeviceConfig) & 1) == 0)
+ break;
+ }
+ if (boguscnt == 0)
+ printk("%s: chipset reset never completed!\n", dev->name);
+ /* wait a little longer */
+ udelay(1000);
+
+ dev->base_addr = (unsigned long)base;
+ dev->irq = irq;
+
+ np = netdev_priv(dev);
+ np->dev = dev;
+ np->base = base;
+ spin_lock_init(&np->lock);
+ pci_set_drvdata(pdev, dev);
+
+ np->pci_dev = pdev;
+
+ np->mii_if.dev = dev;
+ np->mii_if.mdio_read = mdio_read;
+ np->mii_if.mdio_write = mdio_write;
+ np->mii_if.phy_id_mask = 0x1f;
+ np->mii_if.reg_num_mask = 0x1f;
+
+ drv_flags = netdrv_tbl[chip_idx].drv_flags;
+
+ option = card_idx < MAX_UNITS ? options[card_idx] : 0;
+ if (dev->mem_start)
+ option = dev->mem_start;
+
+ /* The lower four bits are the media type. */
+ if (option & 0x200)
+ np->mii_if.full_duplex = 1;
+
+ if (card_idx < MAX_UNITS && full_duplex[card_idx] > 0)
+ np->mii_if.full_duplex = 1;
+
+ if (np->mii_if.full_duplex)
+ np->mii_if.force_media = 1;
+ else
+ np->mii_if.force_media = 0;
+ np->speed100 = 1;
+
+ /* timer resolution is 128 * 0.8us */
+ np->intr_timer_ctrl = (((intr_latency * 10) / 1024) & IntrLatencyMask) |
+ Timer10X | EnableIntrMasking;
+
+ if (small_frames > 0) {
+ np->intr_timer_ctrl |= SmallFrameBypass;
+ switch (small_frames) {
+ case 1 ... 64:
+ np->intr_timer_ctrl |= SmallFrame64;
+ break;
+ case 65 ... 128:
+ np->intr_timer_ctrl |= SmallFrame128;
+ break;
+ case 129 ... 256:
+ np->intr_timer_ctrl |= SmallFrame256;
+ break;
+ default:
+ np->intr_timer_ctrl |= SmallFrame512;
+ if (small_frames > 512)
+ printk("Adjusting small_frames down to 512\n");
+ break;
+ }
+ }
+
+ dev->netdev_ops = &netdev_ops;
+ dev->watchdog_timeo = TX_TIMEOUT;
+ SET_ETHTOOL_OPS(dev, ðtool_ops);
+
+ netif_napi_add(dev, &np->napi, netdev_poll, max_interrupt_work);
+
+ if (mtu)
+ dev->mtu = mtu;
+
+ if (register_netdev(dev))
+ goto err_out_cleardev;
+
+ printk(KERN_INFO "%s: %s at %p, %pM, IRQ %d.\n",
+ dev->name, netdrv_tbl[chip_idx].name, base,
+ dev->dev_addr, irq);
+
+ if (drv_flags & CanHaveMII) {
+ int phy, phy_idx = 0;
+ int mii_status;
+ for (phy = 0; phy < 32 && phy_idx < PHY_CNT; phy++) {
+ mdio_write(dev, phy, MII_BMCR, BMCR_RESET);
+ mdelay(100);
+ boguscnt = 1000;
+ while (--boguscnt > 0)
+ if ((mdio_read(dev, phy, MII_BMCR) & BMCR_RESET) == 0)
+ break;
+ if (boguscnt == 0) {
+ printk("%s: PHY#%d reset never completed!\n", dev->name, phy);
+ continue;
+ }
+ mii_status = mdio_read(dev, phy, MII_BMSR);
+ if (mii_status != 0) {
+ np->phys[phy_idx++] = phy;
+ np->mii_if.advertising = mdio_read(dev, phy, MII_ADVERTISE);
+ printk(KERN_INFO "%s: MII PHY found at address %d, status "
+ "%#4.4x advertising %#4.4x.\n",
+ dev->name, phy, mii_status, np->mii_if.advertising);
+ /* there can be only one PHY on-board */
+ break;
+ }
+ }
+ np->phy_cnt = phy_idx;
+ if (np->phy_cnt > 0)
+ np->mii_if.phy_id = np->phys[0];
+ else
+ memset(&np->mii_if, 0, sizeof(np->mii_if));
+ }
+
+ printk(KERN_INFO "%s: scatter-gather and hardware TCP cksumming %s.\n",
+ dev->name, enable_hw_cksum ? "enabled" : "disabled");
+ return 0;
+
+err_out_cleardev:
+ pci_set_drvdata(pdev, NULL);
+ iounmap(base);
+err_out_free_res:
+ pci_release_regions (pdev);
+err_out_free_netdev:
+ free_netdev(dev);
+ return -ENODEV;
+}
+
+
+/* Read the MII Management Data I/O (MDIO) interfaces. */
+static int mdio_read(struct net_device *dev, int phy_id, int location)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *mdio_addr = np->base + MIICtrl + (phy_id<<7) + (location<<2);
+ int result, boguscnt=1000;
+ /* ??? Should we add a busy-wait here? */
+ do {
+ result = readl(mdio_addr);
+ } while ((result & 0xC0000000) != 0x80000000 && --boguscnt > 0);
+ if (boguscnt == 0)
+ return 0;
+ if ((result & 0xffff) == 0xffff)
+ return 0;
+ return result & 0xffff;
+}
+
+
+static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *mdio_addr = np->base + MIICtrl + (phy_id<<7) + (location<<2);
+ writel(value, mdio_addr);
+ /* The busy-wait will occur before a read. */
+}
+
+
+static int netdev_open(struct net_device *dev)
+{
+ const struct firmware *fw_rx, *fw_tx;
+ const __be32 *fw_rx_data, *fw_tx_data;
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+ int i, retval;
+ size_t tx_size, rx_size;
+ size_t tx_done_q_size, rx_done_q_size, tx_ring_size, rx_ring_size;
+
+ /* Do we ever need to reset the chip??? */
+
+ retval = request_irq(dev->irq, intr_handler, IRQF_SHARED, dev->name, dev);
+ if (retval)
+ return retval;
+
+ /* Disable the Rx and Tx, and reset the chip. */
+ writel(0, ioaddr + GenCtrl);
+ writel(1, ioaddr + PCIDeviceConfig);
+ if (debug > 1)
+ printk(KERN_DEBUG "%s: netdev_open() irq %d.\n",
+ dev->name, dev->irq);
+
+ /* Allocate the various queues. */
+ if (!np->queue_mem) {
+ tx_done_q_size = ((sizeof(struct tx_done_desc) * DONE_Q_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
+ rx_done_q_size = ((sizeof(rx_done_desc) * DONE_Q_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
+ tx_ring_size = ((sizeof(starfire_tx_desc) * TX_RING_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
+ rx_ring_size = sizeof(struct starfire_rx_desc) * RX_RING_SIZE;
+ np->queue_mem_size = tx_done_q_size + rx_done_q_size + tx_ring_size + rx_ring_size;
+ np->queue_mem = pci_alloc_consistent(np->pci_dev, np->queue_mem_size, &np->queue_mem_dma);
+ if (np->queue_mem == NULL) {
+ free_irq(dev->irq, dev);
+ return -ENOMEM;
+ }
+
+ np->tx_done_q = np->queue_mem;
+ np->tx_done_q_dma = np->queue_mem_dma;
+ np->rx_done_q = (void *) np->tx_done_q + tx_done_q_size;
+ np->rx_done_q_dma = np->tx_done_q_dma + tx_done_q_size;
+ np->tx_ring = (void *) np->rx_done_q + rx_done_q_size;
+ np->tx_ring_dma = np->rx_done_q_dma + rx_done_q_size;
+ np->rx_ring = (void *) np->tx_ring + tx_ring_size;
+ np->rx_ring_dma = np->tx_ring_dma + tx_ring_size;
+ }
+
+ /* Start with no carrier, it gets adjusted later */
+ netif_carrier_off(dev);
+ init_ring(dev);
+ /* Set the size of the Rx buffers. */
+ writel((np->rx_buf_sz << RxBufferLenShift) |
+ (0 << RxMinDescrThreshShift) |
+ RxPrefetchMode | RxVariableQ |
+ RX_Q_ENTRIES |
+ RX_DESC_Q_ADDR_SIZE | RX_DESC_ADDR_SIZE |
+ RxDescSpace4,
+ ioaddr + RxDescQCtrl);
+
+ /* Set up the Rx DMA controller. */
+ writel(RxChecksumIgnore |
+ (0 << RxEarlyIntThreshShift) |
+ (6 << RxHighPrioThreshShift) |
+ ((DMA_BURST_SIZE / 32) << RxBurstSizeShift),
+ ioaddr + RxDMACtrl);
+
+ /* Set Tx descriptor */
+ writel((2 << TxHiPriFIFOThreshShift) |
+ (0 << TxPadLenShift) |
+ ((DMA_BURST_SIZE / 32) << TxDMABurstSizeShift) |
+ TX_DESC_Q_ADDR_SIZE |
+ TX_DESC_SPACING | TX_DESC_TYPE,
+ ioaddr + TxDescCtrl);
+
+ writel( (np->queue_mem_dma >> 16) >> 16, ioaddr + RxDescQHiAddr);
+ writel( (np->queue_mem_dma >> 16) >> 16, ioaddr + TxRingHiAddr);
+ writel( (np->queue_mem_dma >> 16) >> 16, ioaddr + CompletionHiAddr);
+ writel(np->rx_ring_dma, ioaddr + RxDescQAddr);
+ writel(np->tx_ring_dma, ioaddr + TxRingPtr);
+
+ writel(np->tx_done_q_dma, ioaddr + TxCompletionAddr);
+ writel(np->rx_done_q_dma |
+ RxComplType |
+ (0 << RxComplThreshShift),
+ ioaddr + RxCompletionAddr);
+
+ if (debug > 1)
+ printk(KERN_DEBUG "%s: Filling in the station address.\n", dev->name);
+
+ /* Fill both the Tx SA register and the Rx perfect filter. */
+ for (i = 0; i < 6; i++)
+ writeb(dev->dev_addr[i], ioaddr + TxStationAddr + 5 - i);
+ /* The first entry is special because it bypasses the VLAN filter.
+ Don't use it. */
+ writew(0, ioaddr + PerfFilterTable);
+ writew(0, ioaddr + PerfFilterTable + 4);
+ writew(0, ioaddr + PerfFilterTable + 8);
+ for (i = 1; i < 16; i++) {
+ __be16 *eaddrs = (__be16 *)dev->dev_addr;
+ void __iomem *setup_frm = ioaddr + PerfFilterTable + i * 16;
+ writew(be16_to_cpu(eaddrs[2]), setup_frm); setup_frm += 4;
+ writew(be16_to_cpu(eaddrs[1]), setup_frm); setup_frm += 4;
+ writew(be16_to_cpu(eaddrs[0]), setup_frm); setup_frm += 8;
+ }
+
+ /* Initialize other registers. */
+ /* Configure the PCI bus bursts and FIFO thresholds. */
+ np->tx_mode = TxFlowEnable|RxFlowEnable|PadEnable; /* modified when link is up. */
+ writel(MiiSoftReset | np->tx_mode, ioaddr + TxMode);
+ udelay(1000);
+ writel(np->tx_mode, ioaddr + TxMode);
+ np->tx_threshold = 4;
+ writel(np->tx_threshold, ioaddr + TxThreshold);
+
+ writel(np->intr_timer_ctrl, ioaddr + IntrTimerCtrl);
+
+ napi_enable(&np->napi);
+
+ netif_start_queue(dev);
+
+ if (debug > 1)
+ printk(KERN_DEBUG "%s: Setting the Rx and Tx modes.\n", dev->name);
+ set_rx_mode(dev);
+
+ np->mii_if.advertising = mdio_read(dev, np->phys[0], MII_ADVERTISE);
+ check_duplex(dev);
+
+ /* Enable GPIO interrupts on link change */
+ writel(0x0f00ff00, ioaddr + GPIOCtrl);
+
+ /* Set the interrupt mask */
+ writel(IntrRxDone | IntrRxEmpty | IntrDMAErr |
+ IntrTxDMADone | IntrStatsMax | IntrLinkChange |
+ IntrRxGFPDead | IntrNoTxCsum | IntrTxBadID,
+ ioaddr + IntrEnable);
+ /* Enable PCI interrupts. */
+ writel(0x00800000 | readl(ioaddr + PCIDeviceConfig),
+ ioaddr + PCIDeviceConfig);
+
+#ifdef VLAN_SUPPORT
+ /* Set VLAN type to 802.1q */
+ writel(ETH_P_8021Q, ioaddr + VlanType);
+#endif /* VLAN_SUPPORT */
+
+ retval = request_firmware(&fw_rx, FIRMWARE_RX, &np->pci_dev->dev);
+ if (retval) {
+ printk(KERN_ERR "starfire: Failed to load firmware \"%s\"\n",
+ FIRMWARE_RX);
+ goto out_init;
+ }
+ if (fw_rx->size % 4) {
+ printk(KERN_ERR "starfire: bogus length %zu in \"%s\"\n",
+ fw_rx->size, FIRMWARE_RX);
+ retval = -EINVAL;
+ goto out_rx;
+ }
+ retval = request_firmware(&fw_tx, FIRMWARE_TX, &np->pci_dev->dev);
+ if (retval) {
+ printk(KERN_ERR "starfire: Failed to load firmware \"%s\"\n",
+ FIRMWARE_TX);
+ goto out_rx;
+ }
+ if (fw_tx->size % 4) {
+ printk(KERN_ERR "starfire: bogus length %zu in \"%s\"\n",
+ fw_tx->size, FIRMWARE_TX);
+ retval = -EINVAL;
+ goto out_tx;
+ }
+ fw_rx_data = (const __be32 *)&fw_rx->data[0];
+ fw_tx_data = (const __be32 *)&fw_tx->data[0];
+ rx_size = fw_rx->size / 4;
+ tx_size = fw_tx->size / 4;
+
+ /* Load Rx/Tx firmware into the frame processors */
+ for (i = 0; i < rx_size; i++)
+ writel(be32_to_cpup(&fw_rx_data[i]), ioaddr + RxGfpMem + i * 4);
+ for (i = 0; i < tx_size; i++)
+ writel(be32_to_cpup(&fw_tx_data[i]), ioaddr + TxGfpMem + i * 4);
+ if (enable_hw_cksum)
+ /* Enable the Rx and Tx units, and the Rx/Tx frame processors. */
+ writel(TxEnable|TxGFPEnable|RxEnable|RxGFPEnable, ioaddr + GenCtrl);
+ else
+ /* Enable the Rx and Tx units only. */
+ writel(TxEnable|RxEnable, ioaddr + GenCtrl);
+
+ if (debug > 1)
+ printk(KERN_DEBUG "%s: Done netdev_open().\n",
+ dev->name);
+
+out_tx:
+ release_firmware(fw_tx);
+out_rx:
+ release_firmware(fw_rx);
+out_init:
+ if (retval)
+ netdev_close(dev);
+ return retval;
+}
+
+
+static void check_duplex(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ u16 reg0;
+ int silly_count = 1000;
+
+ mdio_write(dev, np->phys[0], MII_ADVERTISE, np->mii_if.advertising);
+ mdio_write(dev, np->phys[0], MII_BMCR, BMCR_RESET);
+ udelay(500);
+ while (--silly_count && mdio_read(dev, np->phys[0], MII_BMCR) & BMCR_RESET)
+ /* do nothing */;
+ if (!silly_count) {
+ printk("%s: MII reset failed!\n", dev->name);
+ return;
+ }
+
+ reg0 = mdio_read(dev, np->phys[0], MII_BMCR);
+
+ if (!np->mii_if.force_media) {
+ reg0 |= BMCR_ANENABLE | BMCR_ANRESTART;
+ } else {
+ reg0 &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
+ if (np->speed100)
+ reg0 |= BMCR_SPEED100;
+ if (np->mii_if.full_duplex)
+ reg0 |= BMCR_FULLDPLX;
+ printk(KERN_DEBUG "%s: Link forced to %sMbit %s-duplex\n",
+ dev->name,
+ np->speed100 ? "100" : "10",
+ np->mii_if.full_duplex ? "full" : "half");
+ }
+ mdio_write(dev, np->phys[0], MII_BMCR, reg0);
+}
+
+
+static void tx_timeout(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+ int old_debug;
+
+ printk(KERN_WARNING "%s: Transmit timed out, status %#8.8x, "
+ "resetting...\n", dev->name, (int) readl(ioaddr + IntrStatus));
+
+ /* Perhaps we should reinitialize the hardware here. */
+
+ /*
+ * Stop and restart the interface.
+ * Cheat and increase the debug level temporarily.
+ */
+ old_debug = debug;
+ debug = 2;
+ netdev_close(dev);
+ netdev_open(dev);
+ debug = old_debug;
+
+ /* Trigger an immediate transmit demand. */
+
+ dev->trans_start = jiffies; /* prevent tx timeout */
+ dev->stats.tx_errors++;
+ netif_wake_queue(dev);
+}
+
+
+/* Initialize the Rx and Tx rings, along with various 'dev' bits. */
+static void init_ring(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ int i;
+
+ np->cur_rx = np->cur_tx = np->reap_tx = 0;
+ np->dirty_rx = np->dirty_tx = np->rx_done = np->tx_done = 0;
+
+ np->rx_buf_sz = (dev->mtu <= 1500 ? PKT_BUF_SZ : dev->mtu + 32);
+
+ /* Fill in the Rx buffers. Handle allocation failure gracefully. */
+ for (i = 0; i < RX_RING_SIZE; i++) {
+ struct sk_buff *skb = dev_alloc_skb(np->rx_buf_sz);
+ np->rx_info[i].skb = skb;
+ if (skb == NULL)
+ break;
+ np->rx_info[i].mapping = pci_map_single(np->pci_dev, skb->data, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
+ skb->dev = dev; /* Mark as being used by this device. */
+ /* Grrr, we cannot offset to correctly align the IP header. */
+ np->rx_ring[i].rxaddr = cpu_to_dma(np->rx_info[i].mapping | RxDescValid);
+ }
+ writew(i - 1, np->base + RxDescQIdx);
+ np->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
+
+ /* Clear the remainder of the Rx buffer ring. */
+ for ( ; i < RX_RING_SIZE; i++) {
+ np->rx_ring[i].rxaddr = 0;
+ np->rx_info[i].skb = NULL;
+ np->rx_info[i].mapping = 0;
+ }
+ /* Mark the last entry as wrapping the ring. */
+ np->rx_ring[RX_RING_SIZE - 1].rxaddr |= cpu_to_dma(RxDescEndRing);
+
+ /* Clear the completion rings. */
+ for (i = 0; i < DONE_Q_SIZE; i++) {
+ np->rx_done_q[i].status = 0;
+ np->tx_done_q[i].status = 0;
+ }
+
+ for (i = 0; i < TX_RING_SIZE; i++)
+ memset(&np->tx_info[i], 0, sizeof(np->tx_info[i]));
+}
+
+
+static netdev_tx_t start_tx(struct sk_buff *skb, struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ unsigned int entry;
+ u32 status;
+ int i;
+
+ /*
+ * be cautious here, wrapping the queue has weird semantics
+ * and we may not have enough slots even when it seems we do.
+ */
+ if ((np->cur_tx - np->dirty_tx) + skb_num_frags(skb) * 2 > TX_RING_SIZE) {
+ netif_stop_queue(dev);
+ return NETDEV_TX_BUSY;
+ }
+
+#if defined(ZEROCOPY) && defined(HAS_BROKEN_FIRMWARE)
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ if (skb_padto(skb, (skb->len + PADDING_MASK) & ~PADDING_MASK))
+ return NETDEV_TX_OK;
+ }
+#endif /* ZEROCOPY && HAS_BROKEN_FIRMWARE */
+
+ entry = np->cur_tx % TX_RING_SIZE;
+ for (i = 0; i < skb_num_frags(skb); i++) {
+ int wrap_ring = 0;
+ status = TxDescID;
+
+ if (i == 0) {
+ np->tx_info[entry].skb = skb;
+ status |= TxCRCEn;
+ if (entry >= TX_RING_SIZE - skb_num_frags(skb)) {
+ status |= TxRingWrap;
+ wrap_ring = 1;
+ }
+ if (np->reap_tx) {
+ status |= TxDescIntr;
+ np->reap_tx = 0;
+ }
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ status |= TxCalTCP;
+ dev->stats.tx_compressed++;
+ }
+ status |= skb_first_frag_len(skb) | (skb_num_frags(skb) << 16);
+
+ np->tx_info[entry].mapping =
+ pci_map_single(np->pci_dev, skb->data, skb_first_frag_len(skb), PCI_DMA_TODEVICE);
+ } else {
+ skb_frag_t *this_frag = &skb_shinfo(skb)->frags[i - 1];
+ status |= this_frag->size;
+ np->tx_info[entry].mapping =
+ pci_map_single(np->pci_dev, page_address(this_frag->page) + this_frag->page_offset, this_frag->size, PCI_DMA_TODEVICE);
+ }
+
+ np->tx_ring[entry].addr = cpu_to_dma(np->tx_info[entry].mapping);
+ np->tx_ring[entry].status = cpu_to_le32(status);
+ if (debug > 3)
+ printk(KERN_DEBUG "%s: Tx #%d/#%d slot %d status %#8.8x.\n",
+ dev->name, np->cur_tx, np->dirty_tx,
+ entry, status);
+ if (wrap_ring) {
+ np->tx_info[entry].used_slots = TX_RING_SIZE - entry;
+ np->cur_tx += np->tx_info[entry].used_slots;
+ entry = 0;
+ } else {
+ np->tx_info[entry].used_slots = 1;
+ np->cur_tx += np->tx_info[entry].used_slots;
+ entry++;
+ }
+ /* scavenge the tx descriptors twice per TX_RING_SIZE */
+ if (np->cur_tx % (TX_RING_SIZE / 2) == 0)
+ np->reap_tx = 1;
+ }
+
+ /* Non-x86: explicitly flush descriptor cache lines here. */
+ /* Ensure all descriptors are written back before the transmit is
+ initiated. - Jes */
+ wmb();
+
+ /* Update the producer index. */
+ writel(entry * (sizeof(starfire_tx_desc) / 8), np->base + TxProducerIdx);
+
+ /* 4 is arbitrary, but should be ok */
+ if ((np->cur_tx - np->dirty_tx) + 4 > TX_RING_SIZE)
+ netif_stop_queue(dev);
+
+ return NETDEV_TX_OK;
+}
+
+
+/* The interrupt handler does all of the Rx thread work and cleans up
+ after the Tx thread. */
+static irqreturn_t intr_handler(int irq, void *dev_instance)
+{
+ struct net_device *dev = dev_instance;
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+ int boguscnt = max_interrupt_work;
+ int consumer;
+ int tx_status;
+ int handled = 0;
+
+ do {
+ u32 intr_status = readl(ioaddr + IntrClear);
+
+ if (debug > 4)
+ printk(KERN_DEBUG "%s: Interrupt status %#8.8x.\n",
+ dev->name, intr_status);
+
+ if (intr_status == 0 || intr_status == (u32) -1)
+ break;
+
+ handled = 1;
+
+ if (intr_status & (IntrRxDone | IntrRxEmpty)) {
+ u32 enable;
+
+ if (likely(napi_schedule_prep(&np->napi))) {
+ __napi_schedule(&np->napi);
+ enable = readl(ioaddr + IntrEnable);
+ enable &= ~(IntrRxDone | IntrRxEmpty);
+ writel(enable, ioaddr + IntrEnable);
+ /* flush PCI posting buffers */
+ readl(ioaddr + IntrEnable);
+ } else {
+ /* Paranoia check */
+ enable = readl(ioaddr + IntrEnable);
+ if (enable & (IntrRxDone | IntrRxEmpty)) {
+ printk(KERN_INFO
+ "%s: interrupt while in poll!\n",
+ dev->name);
+ enable &= ~(IntrRxDone | IntrRxEmpty);
+ writel(enable, ioaddr + IntrEnable);
+ }
+ }
+ }
+
+ /* Scavenge the skbuff list based on the Tx-done queue.
+ There are redundant checks here that may be cleaned up
+ after the driver has proven to be reliable. */
+ consumer = readl(ioaddr + TxConsumerIdx);
+ if (debug > 3)
+ printk(KERN_DEBUG "%s: Tx Consumer index is %d.\n",
+ dev->name, consumer);
+
+ while ((tx_status = le32_to_cpu(np->tx_done_q[np->tx_done].status)) != 0) {
+ if (debug > 3)
+ printk(KERN_DEBUG "%s: Tx completion #%d entry %d is %#8.8x.\n",
+ dev->name, np->dirty_tx, np->tx_done, tx_status);
+ if ((tx_status & 0xe0000000) == 0xa0000000) {
+ dev->stats.tx_packets++;
+ } else if ((tx_status & 0xe0000000) == 0x80000000) {
+ u16 entry = (tx_status & 0x7fff) / sizeof(starfire_tx_desc);
+ struct sk_buff *skb = np->tx_info[entry].skb;
+ np->tx_info[entry].skb = NULL;
+ pci_unmap_single(np->pci_dev,
+ np->tx_info[entry].mapping,
+ skb_first_frag_len(skb),
+ PCI_DMA_TODEVICE);
+ np->tx_info[entry].mapping = 0;
+ np->dirty_tx += np->tx_info[entry].used_slots;
+ entry = (entry + np->tx_info[entry].used_slots) % TX_RING_SIZE;
+ {
+ int i;
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ pci_unmap_single(np->pci_dev,
+ np->tx_info[entry].mapping,
+ skb_shinfo(skb)->frags[i].size,
+ PCI_DMA_TODEVICE);
+ np->dirty_tx++;
+ entry++;
+ }
+ }
+
+ dev_kfree_skb_irq(skb);
+ }
+ np->tx_done_q[np->tx_done].status = 0;
+ np->tx_done = (np->tx_done + 1) % DONE_Q_SIZE;
+ }
+ writew(np->tx_done, ioaddr + CompletionQConsumerIdx + 2);
+
+ if (netif_queue_stopped(dev) &&
+ (np->cur_tx - np->dirty_tx + 4 < TX_RING_SIZE)) {
+ /* The ring is no longer full, wake the queue. */
+ netif_wake_queue(dev);
+ }
+
+ /* Stats overflow */
+ if (intr_status & IntrStatsMax)
+ get_stats(dev);
+
+ /* Media change interrupt. */
+ if (intr_status & IntrLinkChange)
+ netdev_media_change(dev);
+
+ /* Abnormal error summary/uncommon events handlers. */
+ if (intr_status & IntrAbnormalSummary)
+ netdev_error(dev, intr_status);
+
+ if (--boguscnt < 0) {
+ if (debug > 1)
+ printk(KERN_WARNING "%s: Too much work at interrupt, "
+ "status=%#8.8x.\n",
+ dev->name, intr_status);
+ break;
+ }
+ } while (1);
+
+ if (debug > 4)
+ printk(KERN_DEBUG "%s: exiting interrupt, status=%#8.8x.\n",
+ dev->name, (int) readl(ioaddr + IntrStatus));
+ return IRQ_RETVAL(handled);
+}
+
+
+/*
+ * This routine is logically part of the interrupt/poll handler, but separated
+ * for clarity and better register allocation.
+ */
+static int __netdev_rx(struct net_device *dev, int *quota)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ u32 desc_status;
+ int retcode = 0;
+
+ /* If EOP is set on the next entry, it's a new packet. Send it up. */
+ while ((desc_status = le32_to_cpu(np->rx_done_q[np->rx_done].status)) != 0) {
+ struct sk_buff *skb;
+ u16 pkt_len;
+ int entry;
+ rx_done_desc *desc = &np->rx_done_q[np->rx_done];
+
+ if (debug > 4)
+ printk(KERN_DEBUG " netdev_rx() status of %d was %#8.8x.\n", np->rx_done, desc_status);
+ if (!(desc_status & RxOK)) {
+ /* There was an error. */
+ if (debug > 2)
+ printk(KERN_DEBUG " netdev_rx() Rx error was %#8.8x.\n", desc_status);
+ dev->stats.rx_errors++;
+ if (desc_status & RxFIFOErr)
+ dev->stats.rx_fifo_errors++;
+ goto next_rx;
+ }
+
+ if (*quota <= 0) { /* out of rx quota */
+ retcode = 1;
+ goto out;
+ }
+ (*quota)--;
+
+ pkt_len = desc_status; /* Implicitly Truncate */
+ entry = (desc_status >> 16) & 0x7ff;
+
+ if (debug > 4)
+ printk(KERN_DEBUG " netdev_rx() normal Rx pkt length %d, quota %d.\n", pkt_len, *quota);
+ /* Check if the packet is long enough to accept without copying
+ to a minimally-sized skbuff. */
+ if (pkt_len < rx_copybreak &&
+ (skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
+ skb_reserve(skb, 2); /* 16 byte align the IP header */
+ pci_dma_sync_single_for_cpu(np->pci_dev,
+ np->rx_info[entry].mapping,
+ pkt_len, PCI_DMA_FROMDEVICE);
+ skb_copy_to_linear_data(skb, np->rx_info[entry].skb->data, pkt_len);
+ pci_dma_sync_single_for_device(np->pci_dev,
+ np->rx_info[entry].mapping,
+ pkt_len, PCI_DMA_FROMDEVICE);
+ skb_put(skb, pkt_len);
+ } else {
+ pci_unmap_single(np->pci_dev, np->rx_info[entry].mapping, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
+ skb = np->rx_info[entry].skb;
+ skb_put(skb, pkt_len);
+ np->rx_info[entry].skb = NULL;
+ np->rx_info[entry].mapping = 0;
+ }
+#ifndef final_version /* Remove after testing. */
+ /* You will want this info for the initial debug. */
+ if (debug > 5) {
+ printk(KERN_DEBUG " Rx data %pM %pM %2.2x%2.2x.\n",
+ skb->data, skb->data + 6,
+ skb->data[12], skb->data[13]);
+ }
+#endif
+
+ skb->protocol = eth_type_trans(skb, dev);
+#ifdef VLAN_SUPPORT
+ if (debug > 4)
+ printk(KERN_DEBUG " netdev_rx() status2 of %d was %#4.4x.\n", np->rx_done, le16_to_cpu(desc->status2));
+#endif
+ if (le16_to_cpu(desc->status2) & 0x0100) {
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ dev->stats.rx_compressed++;
+ }
+ /*
+ * This feature doesn't seem to be working, at least
+ * with the two firmware versions I have. If the GFP sees
+ * an IP fragment, it either ignores it completely, or reports
+ * "bad checksum" on it.
+ *
+ * Maybe I missed something -- corrections are welcome.
+ * Until then, the printk stays. :-) -Ion
+ */
+ else if (le16_to_cpu(desc->status2) & 0x0040) {
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ skb->csum = le16_to_cpu(desc->csum);
+ printk(KERN_DEBUG "%s: checksum_hw, status2 = %#x\n", dev->name, le16_to_cpu(desc->status2));
+ }
+#ifdef VLAN_SUPPORT
+ if (le16_to_cpu(desc->status2) & 0x0200) {
+ u16 vlid = le16_to_cpu(desc->vlanid);
+
+ if (debug > 4) {
+ printk(KERN_DEBUG " netdev_rx() vlanid = %d\n",
+ vlid);
+ }
+ __vlan_hwaccel_put_tag(skb, vlid);
+ }
+#endif /* VLAN_SUPPORT */
+ netif_receive_skb(skb);
+ dev->stats.rx_packets++;
+
+ next_rx:
+ np->cur_rx++;
+ desc->status = 0;
+ np->rx_done = (np->rx_done + 1) % DONE_Q_SIZE;
+ }
+
+ if (*quota == 0) { /* out of rx quota */
+ retcode = 1;
+ goto out;
+ }
+ writew(np->rx_done, np->base + CompletionQConsumerIdx);
+
+ out:
+ refill_rx_ring(dev);
+ if (debug > 5)
+ printk(KERN_DEBUG " exiting netdev_rx(): %d, status of %d was %#8.8x.\n",
+ retcode, np->rx_done, desc_status);
+ return retcode;
+}
+
+static int netdev_poll(struct napi_struct *napi, int budget)
+{
+ struct netdev_private *np = container_of(napi, struct netdev_private, napi);
+ struct net_device *dev = np->dev;
+ u32 intr_status;
+ void __iomem *ioaddr = np->base;
+ int quota = budget;
+
+ do {
+ writel(IntrRxDone | IntrRxEmpty, ioaddr + IntrClear);
+
+ if (__netdev_rx(dev, "a))
+ goto out;
+
+ intr_status = readl(ioaddr + IntrStatus);
+ } while (intr_status & (IntrRxDone | IntrRxEmpty));
+
+ napi_complete(napi);
+ intr_status = readl(ioaddr + IntrEnable);
+ intr_status |= IntrRxDone | IntrRxEmpty;
+ writel(intr_status, ioaddr + IntrEnable);
+
+ out:
+ if (debug > 5)
+ printk(KERN_DEBUG " exiting netdev_poll(): %d.\n",
+ budget - quota);
+
+ /* Restart Rx engine if stopped. */
+ return budget - quota;
+}
+
+static void refill_rx_ring(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ struct sk_buff *skb;
+ int entry = -1;
+
+ /* Refill the Rx ring buffers. */
+ for (; np->cur_rx - np->dirty_rx > 0; np->dirty_rx++) {
+ entry = np->dirty_rx % RX_RING_SIZE;
+ if (np->rx_info[entry].skb == NULL) {
+ skb = dev_alloc_skb(np->rx_buf_sz);
+ np->rx_info[entry].skb = skb;
+ if (skb == NULL)
+ break; /* Better luck next round. */
+ np->rx_info[entry].mapping =
+ pci_map_single(np->pci_dev, skb->data, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
+ skb->dev = dev; /* Mark as being used by this device. */
+ np->rx_ring[entry].rxaddr =
+ cpu_to_dma(np->rx_info[entry].mapping | RxDescValid);
+ }
+ if (entry == RX_RING_SIZE - 1)
+ np->rx_ring[entry].rxaddr |= cpu_to_dma(RxDescEndRing);
+ }
+ if (entry >= 0)
+ writew(entry, np->base + RxDescQIdx);
+}
+
+
+static void netdev_media_change(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+ u16 reg0, reg1, reg4, reg5;
+ u32 new_tx_mode;
+ u32 new_intr_timer_ctrl;
+
+ /* reset status first */
+ mdio_read(dev, np->phys[0], MII_BMCR);
+ mdio_read(dev, np->phys[0], MII_BMSR);
+
+ reg0 = mdio_read(dev, np->phys[0], MII_BMCR);
+ reg1 = mdio_read(dev, np->phys[0], MII_BMSR);
+
+ if (reg1 & BMSR_LSTATUS) {
+ /* link is up */
+ if (reg0 & BMCR_ANENABLE) {
+ /* autonegotiation is enabled */
+ reg4 = mdio_read(dev, np->phys[0], MII_ADVERTISE);
+ reg5 = mdio_read(dev, np->phys[0], MII_LPA);
+ if (reg4 & ADVERTISE_100FULL && reg5 & LPA_100FULL) {
+ np->speed100 = 1;
+ np->mii_if.full_duplex = 1;
+ } else if (reg4 & ADVERTISE_100HALF && reg5 & LPA_100HALF) {
+ np->speed100 = 1;
+ np->mii_if.full_duplex = 0;
+ } else if (reg4 & ADVERTISE_10FULL && reg5 & LPA_10FULL) {
+ np->speed100 = 0;
+ np->mii_if.full_duplex = 1;
+ } else {
+ np->speed100 = 0;
+ np->mii_if.full_duplex = 0;
+ }
+ } else {
+ /* autonegotiation is disabled */
+ if (reg0 & BMCR_SPEED100)
+ np->speed100 = 1;
+ else
+ np->speed100 = 0;
+ if (reg0 & BMCR_FULLDPLX)
+ np->mii_if.full_duplex = 1;
+ else
+ np->mii_if.full_duplex = 0;
+ }
+ netif_carrier_on(dev);
+ printk(KERN_DEBUG "%s: Link is up, running at %sMbit %s-duplex\n",
+ dev->name,
+ np->speed100 ? "100" : "10",
+ np->mii_if.full_duplex ? "full" : "half");
+
+ new_tx_mode = np->tx_mode & ~FullDuplex; /* duplex setting */
+ if (np->mii_if.full_duplex)
+ new_tx_mode |= FullDuplex;
+ if (np->tx_mode != new_tx_mode) {
+ np->tx_mode = new_tx_mode;
+ writel(np->tx_mode | MiiSoftReset, ioaddr + TxMode);
+ udelay(1000);
+ writel(np->tx_mode, ioaddr + TxMode);
+ }
+
+ new_intr_timer_ctrl = np->intr_timer_ctrl & ~Timer10X;
+ if (np->speed100)
+ new_intr_timer_ctrl |= Timer10X;
+ if (np->intr_timer_ctrl != new_intr_timer_ctrl) {
+ np->intr_timer_ctrl = new_intr_timer_ctrl;
+ writel(new_intr_timer_ctrl, ioaddr + IntrTimerCtrl);
+ }
+ } else {
+ netif_carrier_off(dev);
+ printk(KERN_DEBUG "%s: Link is down\n", dev->name);
+ }
+}
+
+
+static void netdev_error(struct net_device *dev, int intr_status)
+{
+ struct netdev_private *np = netdev_priv(dev);
+
+ /* Came close to underrunning the Tx FIFO, increase threshold. */
+ if (intr_status & IntrTxDataLow) {
+ if (np->tx_threshold <= PKT_BUF_SZ / 16) {
+ writel(++np->tx_threshold, np->base + TxThreshold);
+ printk(KERN_NOTICE "%s: PCI bus congestion, increasing Tx FIFO threshold to %d bytes\n",
+ dev->name, np->tx_threshold * 16);
+ } else
+ printk(KERN_WARNING "%s: PCI Tx underflow -- adapter is probably malfunctioning\n", dev->name);
+ }
+ if (intr_status & IntrRxGFPDead) {
+ dev->stats.rx_fifo_errors++;
+ dev->stats.rx_errors++;
+ }
+ if (intr_status & (IntrNoTxCsum | IntrDMAErr)) {
+ dev->stats.tx_fifo_errors++;
+ dev->stats.tx_errors++;
+ }
+ if ((intr_status & ~(IntrNormalMask | IntrAbnormalSummary | IntrLinkChange | IntrStatsMax | IntrTxDataLow | IntrRxGFPDead | IntrNoTxCsum | IntrPCIPad)) && debug)
+ printk(KERN_ERR "%s: Something Wicked happened! %#8.8x.\n",
+ dev->name, intr_status);
+}
+
+
+static struct net_device_stats *get_stats(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+
+ /* This adapter architecture needs no SMP locks. */
+ dev->stats.tx_bytes = readl(ioaddr + 0x57010);
+ dev->stats.rx_bytes = readl(ioaddr + 0x57044);
+ dev->stats.tx_packets = readl(ioaddr + 0x57000);
+ dev->stats.tx_aborted_errors =
+ readl(ioaddr + 0x57024) + readl(ioaddr + 0x57028);
+ dev->stats.tx_window_errors = readl(ioaddr + 0x57018);
+ dev->stats.collisions =
+ readl(ioaddr + 0x57004) + readl(ioaddr + 0x57008);
+
+ /* The chip only need report frame silently dropped. */
+ dev->stats.rx_dropped += readw(ioaddr + RxDMAStatus);
+ writew(0, ioaddr + RxDMAStatus);
+ dev->stats.rx_crc_errors = readl(ioaddr + 0x5703C);
+ dev->stats.rx_frame_errors = readl(ioaddr + 0x57040);
+ dev->stats.rx_length_errors = readl(ioaddr + 0x57058);
+ dev->stats.rx_missed_errors = readl(ioaddr + 0x5707C);
+
+ return &dev->stats;
+}
+
+#ifdef VLAN_SUPPORT
+static u32 set_vlan_mode(struct netdev_private *np)
+{
+ u32 ret = VlanMode;
+ u16 vid;
+ void __iomem *filter_addr = np->base + HashTable + 8;
+ int vlan_count = 0;
+
+ for_each_set_bit(vid, np->active_vlans, VLAN_N_VID) {
+ if (vlan_count == 32)
+ break;
+ writew(vid, filter_addr);
+ filter_addr += 16;
+ vlan_count++;
+ }
+ if (vlan_count == 32) {
+ ret |= PerfectFilterVlan;
+ while (vlan_count < 32) {
+ writew(0, filter_addr);
+ filter_addr += 16;
+ vlan_count++;
+ }
+ }
+ return ret;
+}
+#endif /* VLAN_SUPPORT */
+
+static void set_rx_mode(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+ u32 rx_mode = MinVLANPrio;
+ struct netdev_hw_addr *ha;
+ int i;
+
+#ifdef VLAN_SUPPORT
+ rx_mode |= set_vlan_mode(np);
+#endif /* VLAN_SUPPORT */
+
+ if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
+ rx_mode |= AcceptAll;
+ } else if ((netdev_mc_count(dev) > multicast_filter_limit) ||
+ (dev->flags & IFF_ALLMULTI)) {
+ /* Too many to match, or accept all multicasts. */
+ rx_mode |= AcceptBroadcast|AcceptAllMulticast|PerfectFilter;
+ } else if (netdev_mc_count(dev) <= 14) {
+ /* Use the 16 element perfect filter, skip first two entries. */
+ void __iomem *filter_addr = ioaddr + PerfFilterTable + 2 * 16;
+ __be16 *eaddrs;
+ netdev_for_each_mc_addr(ha, dev) {
+ eaddrs = (__be16 *) ha->addr;
+ writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 4;
+ writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
+ writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 8;
+ }
+ eaddrs = (__be16 *)dev->dev_addr;
+ i = netdev_mc_count(dev) + 2;
+ while (i++ < 16) {
+ writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 4;
+ writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
+ writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 8;
+ }
+ rx_mode |= AcceptBroadcast|PerfectFilter;
+ } else {
+ /* Must use a multicast hash table. */
+ void __iomem *filter_addr;
+ __be16 *eaddrs;
+ __le16 mc_filter[32] __attribute__ ((aligned(sizeof(long)))); /* Multicast hash filter */
+
+ memset(mc_filter, 0, sizeof(mc_filter));
+ netdev_for_each_mc_addr(ha, dev) {
+ /* The chip uses the upper 9 CRC bits
+ as index into the hash table */
+ int bit_nr = ether_crc_le(ETH_ALEN, ha->addr) >> 23;
+ __le32 *fptr = (__le32 *) &mc_filter[(bit_nr >> 4) & ~1];
+
+ *fptr |= cpu_to_le32(1 << (bit_nr & 31));
+ }
+ /* Clear the perfect filter list, skip first two entries. */
+ filter_addr = ioaddr + PerfFilterTable + 2 * 16;
+ eaddrs = (__be16 *)dev->dev_addr;
+ for (i = 2; i < 16; i++) {
+ writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 4;
+ writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
+ writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 8;
+ }
+ for (filter_addr = ioaddr + HashTable, i = 0; i < 32; filter_addr+= 16, i++)
+ writew(mc_filter[i], filter_addr);
+ rx_mode |= AcceptBroadcast|PerfectFilter|HashFilter;
+ }
+ writel(rx_mode, ioaddr + RxFilterMode);
+}
+
+static int check_if_running(struct net_device *dev)
+{
+ if (!netif_running(dev))
+ return -EINVAL;
+ return 0;
+}
+
+static void get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ strcpy(info->driver, DRV_NAME);
+ strcpy(info->version, DRV_VERSION);
+ strcpy(info->bus_info, pci_name(np->pci_dev));
+}
+
+static int get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ spin_lock_irq(&np->lock);
+ mii_ethtool_gset(&np->mii_if, ecmd);
+ spin_unlock_irq(&np->lock);
+ return 0;
+}
+
+static int set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ int res;
+ spin_lock_irq(&np->lock);
+ res = mii_ethtool_sset(&np->mii_if, ecmd);
+ spin_unlock_irq(&np->lock);
+ check_duplex(dev);
+ return res;
+}
+
+static int nway_reset(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ return mii_nway_restart(&np->mii_if);
+}
+
+static u32 get_link(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ return mii_link_ok(&np->mii_if);
+}
+
+static u32 get_msglevel(struct net_device *dev)
+{
+ return debug;
+}
+
+static void set_msglevel(struct net_device *dev, u32 val)
+{
+ debug = val;
+}
+
+static const struct ethtool_ops ethtool_ops = {
+ .begin = check_if_running,
+ .get_drvinfo = get_drvinfo,
+ .get_settings = get_settings,
+ .set_settings = set_settings,
+ .nway_reset = nway_reset,
+ .get_link = get_link,
+ .get_msglevel = get_msglevel,
+ .set_msglevel = set_msglevel,
+};
+
+static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ struct mii_ioctl_data *data = if_mii(rq);
+ int rc;
+
+ if (!netif_running(dev))
+ return -EINVAL;
+
+ spin_lock_irq(&np->lock);
+ rc = generic_mii_ioctl(&np->mii_if, data, cmd, NULL);
+ spin_unlock_irq(&np->lock);
+
+ if ((cmd == SIOCSMIIREG) && (data->phy_id == np->phys[0]))
+ check_duplex(dev);
+
+ return rc;
+}
+
+static int netdev_close(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->base;
+ int i;
+
+ netif_stop_queue(dev);
+
+ napi_disable(&np->napi);
+
+ if (debug > 1) {
+ printk(KERN_DEBUG "%s: Shutting down ethercard, Intr status %#8.8x.\n",
+ dev->name, (int) readl(ioaddr + IntrStatus));
+ printk(KERN_DEBUG "%s: Queue pointers were Tx %d / %d, Rx %d / %d.\n",
+ dev->name, np->cur_tx, np->dirty_tx,
+ np->cur_rx, np->dirty_rx);
+ }
+
+ /* Disable interrupts by clearing the interrupt mask. */
+ writel(0, ioaddr + IntrEnable);
+
+ /* Stop the chip's Tx and Rx processes. */
+ writel(0, ioaddr + GenCtrl);
+ readl(ioaddr + GenCtrl);
+
+ if (debug > 5) {
+ printk(KERN_DEBUG" Tx ring at %#llx:\n",
+ (long long) np->tx_ring_dma);
+ for (i = 0; i < 8 /* TX_RING_SIZE is huge! */; i++)
+ printk(KERN_DEBUG " #%d desc. %#8.8x %#llx -> %#8.8x.\n",
+ i, le32_to_cpu(np->tx_ring[i].status),
+ (long long) dma_to_cpu(np->tx_ring[i].addr),
+ le32_to_cpu(np->tx_done_q[i].status));
+ printk(KERN_DEBUG " Rx ring at %#llx -> %p:\n",
+ (long long) np->rx_ring_dma, np->rx_done_q);
+ if (np->rx_done_q)
+ for (i = 0; i < 8 /* RX_RING_SIZE */; i++) {
+ printk(KERN_DEBUG " #%d desc. %#llx -> %#8.8x\n",
+ i, (long long) dma_to_cpu(np->rx_ring[i].rxaddr), le32_to_cpu(np->rx_done_q[i].status));
+ }
+ }
+
+ free_irq(dev->irq, dev);
+
+ /* Free all the skbuffs in the Rx queue. */
+ for (i = 0; i < RX_RING_SIZE; i++) {
+ np->rx_ring[i].rxaddr = cpu_to_dma(0xBADF00D0); /* An invalid address. */
+ if (np->rx_info[i].skb != NULL) {
+ pci_unmap_single(np->pci_dev, np->rx_info[i].mapping, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(np->rx_info[i].skb);
+ }
+ np->rx_info[i].skb = NULL;
+ np->rx_info[i].mapping = 0;
+ }
+ for (i = 0; i < TX_RING_SIZE; i++) {
+ struct sk_buff *skb = np->tx_info[i].skb;
+ if (skb == NULL)
+ continue;
+ pci_unmap_single(np->pci_dev,
+ np->tx_info[i].mapping,
+ skb_first_frag_len(skb), PCI_DMA_TODEVICE);
+ np->tx_info[i].mapping = 0;
+ dev_kfree_skb(skb);
+ np->tx_info[i].skb = NULL;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int starfire_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+
+ if (netif_running(dev)) {
+ netif_device_detach(dev);
+ netdev_close(dev);
+ }
+
+ pci_save_state(pdev);
+ pci_set_power_state(pdev, pci_choose_state(pdev,state));
+
+ return 0;
+}
+
+static int starfire_resume(struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+
+ if (netif_running(dev)) {
+ netdev_open(dev);
+ netif_device_attach(dev);
+ }
+
+ return 0;
+}
+#endif /* CONFIG_PM */
+
+
+static void __devexit starfire_remove_one (struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct netdev_private *np = netdev_priv(dev);
+
+ BUG_ON(!dev);
+
+ unregister_netdev(dev);
+
+ if (np->queue_mem)
+ pci_free_consistent(pdev, np->queue_mem_size, np->queue_mem, np->queue_mem_dma);
+
+
+ /* XXX: add wakeup code -- requires firmware for MagicPacket */
+ pci_set_power_state(pdev, PCI_D3hot); /* go to sleep in D3 mode */
+ pci_disable_device(pdev);
+
+ iounmap(np->base);
+ pci_release_regions(pdev);
+
+ pci_set_drvdata(pdev, NULL);
+ free_netdev(dev); /* Will also free np!! */
+}
+
+
+static struct pci_driver starfire_driver = {
+ .name = DRV_NAME,
+ .probe = starfire_init_one,
+ .remove = __devexit_p(starfire_remove_one),
+#ifdef CONFIG_PM
+ .suspend = starfire_suspend,
+ .resume = starfire_resume,
+#endif /* CONFIG_PM */
+ .id_table = starfire_pci_tbl,
+};
+
+
+static int __init starfire_init (void)
+{
+/* when a module, this is printed whether or not devices are found in probe */
+#ifdef MODULE
+ printk(version);
+
+ printk(KERN_INFO DRV_NAME ": polling (NAPI) enabled\n");
+#endif
+
+ BUILD_BUG_ON(sizeof(dma_addr_t) != sizeof(netdrv_addr_t));
+
+ return pci_register_driver(&starfire_driver);
+}
+
+
+static void __exit starfire_cleanup (void)
+{
+ pci_unregister_driver (&starfire_driver);
+}
+
+
+module_init(starfire_init);
+module_exit(starfire_cleanup);
+
+
+/*
+ * Local variables:
+ * c-basic-offset: 8
+ * tab-width: 8
+ * End:
+ */
+++ /dev/null
-/* starfire.c: Linux device driver for the Adaptec Starfire network adapter. */
-/*
- Written 1998-2000 by Donald Becker.
-
- Current maintainer is Ion Badulescu <ionut ta badula tod org>. Please
- send all bug reports to me, and not to Donald Becker, as this code
- has been heavily modified from Donald's original version.
-
- This software may be used and distributed according to the terms of
- the GNU General Public License (GPL), incorporated herein by reference.
- Drivers based on or derived from this code fall under the GPL and must
- retain the authorship, copyright and license notice. This file is not
- a complete program and may only be used when the entire operating
- system is licensed under the GPL.
-
- The information below comes from Donald Becker's original driver:
-
- The author may be reached as becker@scyld.com, or C/O
- Scyld Computing Corporation
- 410 Severn Ave., Suite 210
- Annapolis MD 21403
-
- Support and updates available at
- http://www.scyld.com/network/starfire.html
- [link no longer provides useful info -jgarzik]
-
-*/
-
-#define DRV_NAME "starfire"
-#define DRV_VERSION "2.1"
-#define DRV_RELDATE "July 6, 2008"
-
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/crc32.h>
-#include <linux/ethtool.h>
-#include <linux/mii.h>
-#include <linux/if_vlan.h>
-#include <linux/mm.h>
-#include <linux/firmware.h>
-#include <asm/processor.h> /* Processor type for cache alignment. */
-#include <asm/uaccess.h>
-#include <asm/io.h>
-
-/*
- * The current frame processor firmware fails to checksum a fragment
- * of length 1. If and when this is fixed, the #define below can be removed.
- */
-#define HAS_BROKEN_FIRMWARE
-
-/*
- * If using the broken firmware, data must be padded to the next 32-bit boundary.
- */
-#ifdef HAS_BROKEN_FIRMWARE
-#define PADDING_MASK 3
-#endif
-
-/*
- * Define this if using the driver with the zero-copy patch
- */
-#define ZEROCOPY
-
-#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
-#define VLAN_SUPPORT
-#endif
-
-/* The user-configurable values.
- These may be modified when a driver module is loaded.*/
-
-/* Used for tuning interrupt latency vs. overhead. */
-static int intr_latency;
-static int small_frames;
-
-static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */
-static int max_interrupt_work = 20;
-static int mtu;
-/* Maximum number of multicast addresses to filter (vs. rx-all-multicast).
- The Starfire has a 512 element hash table based on the Ethernet CRC. */
-static const int multicast_filter_limit = 512;
-/* Whether to do TCP/UDP checksums in hardware */
-static int enable_hw_cksum = 1;
-
-#define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
-/*
- * Set the copy breakpoint for the copy-only-tiny-frames scheme.
- * Setting to > 1518 effectively disables this feature.
- *
- * NOTE:
- * The ia64 doesn't allow for unaligned loads even of integers being
- * misaligned on a 2 byte boundary. Thus always force copying of
- * packets as the starfire doesn't allow for misaligned DMAs ;-(
- * 23/10/2000 - Jes
- *
- * The Alpha and the Sparc don't like unaligned loads, either. On Sparc64,
- * at least, having unaligned frames leads to a rather serious performance
- * penalty. -Ion
- */
-#if defined(__ia64__) || defined(__alpha__) || defined(__sparc__)
-static int rx_copybreak = PKT_BUF_SZ;
-#else
-static int rx_copybreak /* = 0 */;
-#endif
-
-/* PCI DMA burst size -- on sparc64 we want to force it to 64 bytes, on the others the default of 128 is fine. */
-#ifdef __sparc__
-#define DMA_BURST_SIZE 64
-#else
-#define DMA_BURST_SIZE 128
-#endif
-
-/* Used to pass the media type, etc.
- Both 'options[]' and 'full_duplex[]' exist for driver interoperability.
- The media type is usually passed in 'options[]'.
- These variables are deprecated, use ethtool instead. -Ion
-*/
-#define MAX_UNITS 8 /* More are supported, limit only on options */
-static int options[MAX_UNITS] = {0, };
-static int full_duplex[MAX_UNITS] = {0, };
-
-/* Operational parameters that are set at compile time. */
-
-/* The "native" ring sizes are either 256 or 2048.
- However in some modes a descriptor may be marked to wrap the ring earlier.
-*/
-#define RX_RING_SIZE 256
-#define TX_RING_SIZE 32
-/* The completion queues are fixed at 1024 entries i.e. 4K or 8KB. */
-#define DONE_Q_SIZE 1024
-/* All queues must be aligned on a 256-byte boundary */
-#define QUEUE_ALIGN 256
-
-#if RX_RING_SIZE > 256
-#define RX_Q_ENTRIES Rx2048QEntries
-#else
-#define RX_Q_ENTRIES Rx256QEntries
-#endif
-
-/* Operational parameters that usually are not changed. */
-/* Time in jiffies before concluding the transmitter is hung. */
-#define TX_TIMEOUT (2 * HZ)
-
-#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
-/* 64-bit dma_addr_t */
-#define ADDR_64BITS /* This chip uses 64 bit addresses. */
-#define netdrv_addr_t __le64
-#define cpu_to_dma(x) cpu_to_le64(x)
-#define dma_to_cpu(x) le64_to_cpu(x)
-#define RX_DESC_Q_ADDR_SIZE RxDescQAddr64bit
-#define TX_DESC_Q_ADDR_SIZE TxDescQAddr64bit
-#define RX_COMPL_Q_ADDR_SIZE RxComplQAddr64bit
-#define TX_COMPL_Q_ADDR_SIZE TxComplQAddr64bit
-#define RX_DESC_ADDR_SIZE RxDescAddr64bit
-#else /* 32-bit dma_addr_t */
-#define netdrv_addr_t __le32
-#define cpu_to_dma(x) cpu_to_le32(x)
-#define dma_to_cpu(x) le32_to_cpu(x)
-#define RX_DESC_Q_ADDR_SIZE RxDescQAddr32bit
-#define TX_DESC_Q_ADDR_SIZE TxDescQAddr32bit
-#define RX_COMPL_Q_ADDR_SIZE RxComplQAddr32bit
-#define TX_COMPL_Q_ADDR_SIZE TxComplQAddr32bit
-#define RX_DESC_ADDR_SIZE RxDescAddr32bit
-#endif
-
-#define skb_first_frag_len(skb) skb_headlen(skb)
-#define skb_num_frags(skb) (skb_shinfo(skb)->nr_frags + 1)
-
-/* Firmware names */
-#define FIRMWARE_RX "adaptec/starfire_rx.bin"
-#define FIRMWARE_TX "adaptec/starfire_tx.bin"
-
-/* These identify the driver base version and may not be removed. */
-static const char version[] __devinitconst =
-KERN_INFO "starfire.c:v1.03 7/26/2000 Written by Donald Becker <becker@scyld.com>\n"
-" (unofficial 2.2/2.4 kernel port, version " DRV_VERSION ", " DRV_RELDATE ")\n";
-
-MODULE_AUTHOR("Donald Becker <becker@scyld.com>");
-MODULE_DESCRIPTION("Adaptec Starfire Ethernet driver");
-MODULE_LICENSE("GPL");
-MODULE_VERSION(DRV_VERSION);
-MODULE_FIRMWARE(FIRMWARE_RX);
-MODULE_FIRMWARE(FIRMWARE_TX);
-
-module_param(max_interrupt_work, int, 0);
-module_param(mtu, int, 0);
-module_param(debug, int, 0);
-module_param(rx_copybreak, int, 0);
-module_param(intr_latency, int, 0);
-module_param(small_frames, int, 0);
-module_param_array(options, int, NULL, 0);
-module_param_array(full_duplex, int, NULL, 0);
-module_param(enable_hw_cksum, int, 0);
-MODULE_PARM_DESC(max_interrupt_work, "Maximum events handled per interrupt");
-MODULE_PARM_DESC(mtu, "MTU (all boards)");
-MODULE_PARM_DESC(debug, "Debug level (0-6)");
-MODULE_PARM_DESC(rx_copybreak, "Copy breakpoint for copy-only-tiny-frames");
-MODULE_PARM_DESC(intr_latency, "Maximum interrupt latency, in microseconds");
-MODULE_PARM_DESC(small_frames, "Maximum size of receive frames that bypass interrupt latency (0,64,128,256,512)");
-MODULE_PARM_DESC(options, "Deprecated: Bits 0-3: media type, bit 17: full duplex");
-MODULE_PARM_DESC(full_duplex, "Deprecated: Forced full-duplex setting (0/1)");
-MODULE_PARM_DESC(enable_hw_cksum, "Enable/disable hardware cksum support (0/1)");
-
-/*
- Theory of Operation
-
-I. Board Compatibility
-
-This driver is for the Adaptec 6915 "Starfire" 64 bit PCI Ethernet adapter.
-
-II. Board-specific settings
-
-III. Driver operation
-
-IIIa. Ring buffers
-
-The Starfire hardware uses multiple fixed-size descriptor queues/rings. The
-ring sizes are set fixed by the hardware, but may optionally be wrapped
-earlier by the END bit in the descriptor.
-This driver uses that hardware queue size for the Rx ring, where a large
-number of entries has no ill effect beyond increases the potential backlog.
-The Tx ring is wrapped with the END bit, since a large hardware Tx queue
-disables the queue layer priority ordering and we have no mechanism to
-utilize the hardware two-level priority queue. When modifying the
-RX/TX_RING_SIZE pay close attention to page sizes and the ring-empty warning
-levels.
-
-IIIb/c. Transmit/Receive Structure
-
-See the Adaptec manual for the many possible structures, and options for
-each structure. There are far too many to document all of them here.
-
-For transmit this driver uses type 0/1 transmit descriptors (depending
-on the 32/64 bitness of the architecture), and relies on automatic
-minimum-length padding. It does not use the completion queue
-consumer index, but instead checks for non-zero status entries.
-
-For receive this driver uses type 2/3 receive descriptors. The driver
-allocates full frame size skbuffs for the Rx ring buffers, so all frames
-should fit in a single descriptor. The driver does not use the completion
-queue consumer index, but instead checks for non-zero status entries.
-
-When an incoming frame is less than RX_COPYBREAK bytes long, a fresh skbuff
-is allocated and the frame is copied to the new skbuff. When the incoming
-frame is larger, the skbuff is passed directly up the protocol stack.
-Buffers consumed this way are replaced by newly allocated skbuffs in a later
-phase of receive.
-
-A notable aspect of operation is that unaligned buffers are not permitted by
-the Starfire hardware. Thus the IP header at offset 14 in an ethernet frame
-isn't longword aligned, which may cause problems on some machine
-e.g. Alphas and IA64. For these architectures, the driver is forced to copy
-the frame into a new skbuff unconditionally. Copied frames are put into the
-skbuff at an offset of "+2", thus 16-byte aligning the IP header.
-
-IIId. Synchronization
-
-The driver runs as two independent, single-threaded flows of control. One
-is the send-packet routine, which enforces single-threaded use by the
-dev->tbusy flag. The other thread is the interrupt handler, which is single
-threaded by the hardware and interrupt handling software.
-
-The send packet thread has partial control over the Tx ring and the netif_queue
-status. If the number of free Tx slots in the ring falls below a certain number
-(currently hardcoded to 4), it signals the upper layer to stop the queue.
-
-The interrupt handler has exclusive control over the Rx ring and records stats
-from the Tx ring. After reaping the stats, it marks the Tx queue entry as
-empty by incrementing the dirty_tx mark. Iff the netif_queue is stopped and the
-number of free Tx slow is above the threshold, it signals the upper layer to
-restart the queue.
-
-IV. Notes
-
-IVb. References
-
-The Adaptec Starfire manuals, available only from Adaptec.
-http://www.scyld.com/expert/100mbps.html
-http://www.scyld.com/expert/NWay.html
-
-IVc. Errata
-
-- StopOnPerr is broken, don't enable
-- Hardware ethernet padding exposes random data, perform software padding
- instead (unverified -- works correctly for all the hardware I have)
-
-*/
-
-
-
-enum chip_capability_flags {CanHaveMII=1, };
-
-enum chipset {
- CH_6915 = 0,
-};
-
-static DEFINE_PCI_DEVICE_TABLE(starfire_pci_tbl) = {
- { PCI_VDEVICE(ADAPTEC, 0x6915), CH_6915 },
- { 0, }
-};
-MODULE_DEVICE_TABLE(pci, starfire_pci_tbl);
-
-/* A chip capabilities table, matching the CH_xxx entries in xxx_pci_tbl[] above. */
-static const struct chip_info {
- const char *name;
- int drv_flags;
-} netdrv_tbl[] __devinitdata = {
- { "Adaptec Starfire 6915", CanHaveMII },
-};
-
-
-/* Offsets to the device registers.
- Unlike software-only systems, device drivers interact with complex hardware.
- It's not useful to define symbolic names for every register bit in the
- device. The name can only partially document the semantics and make
- the driver longer and more difficult to read.
- In general, only the important configuration values or bits changed
- multiple times should be defined symbolically.
-*/
-enum register_offsets {
- PCIDeviceConfig=0x50040, GenCtrl=0x50070, IntrTimerCtrl=0x50074,
- IntrClear=0x50080, IntrStatus=0x50084, IntrEnable=0x50088,
- MIICtrl=0x52000, TxStationAddr=0x50120, EEPROMCtrl=0x51000,
- GPIOCtrl=0x5008C, TxDescCtrl=0x50090,
- TxRingPtr=0x50098, HiPriTxRingPtr=0x50094, /* Low and High priority. */
- TxRingHiAddr=0x5009C, /* 64 bit address extension. */
- TxProducerIdx=0x500A0, TxConsumerIdx=0x500A4,
- TxThreshold=0x500B0,
- CompletionHiAddr=0x500B4, TxCompletionAddr=0x500B8,
- RxCompletionAddr=0x500BC, RxCompletionQ2Addr=0x500C0,
- CompletionQConsumerIdx=0x500C4, RxDMACtrl=0x500D0,
- RxDescQCtrl=0x500D4, RxDescQHiAddr=0x500DC, RxDescQAddr=0x500E0,
- RxDescQIdx=0x500E8, RxDMAStatus=0x500F0, RxFilterMode=0x500F4,
- TxMode=0x55000, VlanType=0x55064,
- PerfFilterTable=0x56000, HashTable=0x56100,
- TxGfpMem=0x58000, RxGfpMem=0x5a000,
-};
-
-/*
- * Bits in the interrupt status/mask registers.
- * Warning: setting Intr[Ab]NormalSummary in the IntrEnable register
- * enables all the interrupt sources that are or'ed into those status bits.
- */
-enum intr_status_bits {
- IntrLinkChange=0xf0000000, IntrStatsMax=0x08000000,
- IntrAbnormalSummary=0x02000000, IntrGeneralTimer=0x01000000,
- IntrSoftware=0x800000, IntrRxComplQ1Low=0x400000,
- IntrTxComplQLow=0x200000, IntrPCI=0x100000,
- IntrDMAErr=0x080000, IntrTxDataLow=0x040000,
- IntrRxComplQ2Low=0x020000, IntrRxDescQ1Low=0x010000,
- IntrNormalSummary=0x8000, IntrTxDone=0x4000,
- IntrTxDMADone=0x2000, IntrTxEmpty=0x1000,
- IntrEarlyRxQ2=0x0800, IntrEarlyRxQ1=0x0400,
- IntrRxQ2Done=0x0200, IntrRxQ1Done=0x0100,
- IntrRxGFPDead=0x80, IntrRxDescQ2Low=0x40,
- IntrNoTxCsum=0x20, IntrTxBadID=0x10,
- IntrHiPriTxBadID=0x08, IntrRxGfp=0x04,
- IntrTxGfp=0x02, IntrPCIPad=0x01,
- /* not quite bits */
- IntrRxDone=IntrRxQ2Done | IntrRxQ1Done,
- IntrRxEmpty=IntrRxDescQ1Low | IntrRxDescQ2Low,
- IntrNormalMask=0xff00, IntrAbnormalMask=0x3ff00fe,
-};
-
-/* Bits in the RxFilterMode register. */
-enum rx_mode_bits {
- AcceptBroadcast=0x04, AcceptAllMulticast=0x02, AcceptAll=0x01,
- AcceptMulticast=0x10, PerfectFilter=0x40, HashFilter=0x30,
- PerfectFilterVlan=0x80, MinVLANPrio=0xE000, VlanMode=0x0200,
- WakeupOnGFP=0x0800,
-};
-
-/* Bits in the TxMode register */
-enum tx_mode_bits {
- MiiSoftReset=0x8000, MIILoopback=0x4000,
- TxFlowEnable=0x0800, RxFlowEnable=0x0400,
- PadEnable=0x04, FullDuplex=0x02, HugeFrame=0x01,
-};
-
-/* Bits in the TxDescCtrl register. */
-enum tx_ctrl_bits {
- TxDescSpaceUnlim=0x00, TxDescSpace32=0x10, TxDescSpace64=0x20,
- TxDescSpace128=0x30, TxDescSpace256=0x40,
- TxDescType0=0x00, TxDescType1=0x01, TxDescType2=0x02,
- TxDescType3=0x03, TxDescType4=0x04,
- TxNoDMACompletion=0x08,
- TxDescQAddr64bit=0x80, TxDescQAddr32bit=0,
- TxHiPriFIFOThreshShift=24, TxPadLenShift=16,
- TxDMABurstSizeShift=8,
-};
-
-/* Bits in the RxDescQCtrl register. */
-enum rx_ctrl_bits {
- RxBufferLenShift=16, RxMinDescrThreshShift=0,
- RxPrefetchMode=0x8000, RxVariableQ=0x2000,
- Rx2048QEntries=0x4000, Rx256QEntries=0,
- RxDescAddr64bit=0x1000, RxDescAddr32bit=0,
- RxDescQAddr64bit=0x0100, RxDescQAddr32bit=0,
- RxDescSpace4=0x000, RxDescSpace8=0x100,
- RxDescSpace16=0x200, RxDescSpace32=0x300,
- RxDescSpace64=0x400, RxDescSpace128=0x500,
- RxConsumerWrEn=0x80,
-};
-
-/* Bits in the RxDMACtrl register. */
-enum rx_dmactrl_bits {
- RxReportBadFrames=0x80000000, RxDMAShortFrames=0x40000000,
- RxDMABadFrames=0x20000000, RxDMACrcErrorFrames=0x10000000,
- RxDMAControlFrame=0x08000000, RxDMAPauseFrame=0x04000000,
- RxChecksumIgnore=0, RxChecksumRejectTCPUDP=0x02000000,
- RxChecksumRejectTCPOnly=0x01000000,
- RxCompletionQ2Enable=0x800000,
- RxDMAQ2Disable=0, RxDMAQ2FPOnly=0x100000,
- RxDMAQ2SmallPkt=0x200000, RxDMAQ2HighPrio=0x300000,
- RxDMAQ2NonIP=0x400000,
- RxUseBackupQueue=0x080000, RxDMACRC=0x040000,
- RxEarlyIntThreshShift=12, RxHighPrioThreshShift=8,
- RxBurstSizeShift=0,
-};
-
-/* Bits in the RxCompletionAddr register */
-enum rx_compl_bits {
- RxComplQAddr64bit=0x80, RxComplQAddr32bit=0,
- RxComplProducerWrEn=0x40,
- RxComplType0=0x00, RxComplType1=0x10,
- RxComplType2=0x20, RxComplType3=0x30,
- RxComplThreshShift=0,
-};
-
-/* Bits in the TxCompletionAddr register */
-enum tx_compl_bits {
- TxComplQAddr64bit=0x80, TxComplQAddr32bit=0,
- TxComplProducerWrEn=0x40,
- TxComplIntrStatus=0x20,
- CommonQueueMode=0x10,
- TxComplThreshShift=0,
-};
-
-/* Bits in the GenCtrl register */
-enum gen_ctrl_bits {
- RxEnable=0x05, TxEnable=0x0a,
- RxGFPEnable=0x10, TxGFPEnable=0x20,
-};
-
-/* Bits in the IntrTimerCtrl register */
-enum intr_ctrl_bits {
- Timer10X=0x800, EnableIntrMasking=0x60, SmallFrameBypass=0x100,
- SmallFrame64=0, SmallFrame128=0x200, SmallFrame256=0x400, SmallFrame512=0x600,
- IntrLatencyMask=0x1f,
-};
-
-/* The Rx and Tx buffer descriptors. */
-struct starfire_rx_desc {
- netdrv_addr_t rxaddr;
-};
-enum rx_desc_bits {
- RxDescValid=1, RxDescEndRing=2,
-};
-
-/* Completion queue entry. */
-struct short_rx_done_desc {
- __le32 status; /* Low 16 bits is length. */
-};
-struct basic_rx_done_desc {
- __le32 status; /* Low 16 bits is length. */
- __le16 vlanid;
- __le16 status2;
-};
-struct csum_rx_done_desc {
- __le32 status; /* Low 16 bits is length. */
- __le16 csum; /* Partial checksum */
- __le16 status2;
-};
-struct full_rx_done_desc {
- __le32 status; /* Low 16 bits is length. */
- __le16 status3;
- __le16 status2;
- __le16 vlanid;
- __le16 csum; /* partial checksum */
- __le32 timestamp;
-};
-/* XXX: this is ugly and I'm not sure it's worth the trouble -Ion */
-#ifdef VLAN_SUPPORT
-typedef struct full_rx_done_desc rx_done_desc;
-#define RxComplType RxComplType3
-#else /* not VLAN_SUPPORT */
-typedef struct csum_rx_done_desc rx_done_desc;
-#define RxComplType RxComplType2
-#endif /* not VLAN_SUPPORT */
-
-enum rx_done_bits {
- RxOK=0x20000000, RxFIFOErr=0x10000000, RxBufQ2=0x08000000,
-};
-
-/* Type 1 Tx descriptor. */
-struct starfire_tx_desc_1 {
- __le32 status; /* Upper bits are status, lower 16 length. */
- __le32 addr;
-};
-
-/* Type 2 Tx descriptor. */
-struct starfire_tx_desc_2 {
- __le32 status; /* Upper bits are status, lower 16 length. */
- __le32 reserved;
- __le64 addr;
-};
-
-#ifdef ADDR_64BITS
-typedef struct starfire_tx_desc_2 starfire_tx_desc;
-#define TX_DESC_TYPE TxDescType2
-#else /* not ADDR_64BITS */
-typedef struct starfire_tx_desc_1 starfire_tx_desc;
-#define TX_DESC_TYPE TxDescType1
-#endif /* not ADDR_64BITS */
-#define TX_DESC_SPACING TxDescSpaceUnlim
-
-enum tx_desc_bits {
- TxDescID=0xB0000000,
- TxCRCEn=0x01000000, TxDescIntr=0x08000000,
- TxRingWrap=0x04000000, TxCalTCP=0x02000000,
-};
-struct tx_done_desc {
- __le32 status; /* timestamp, index. */
-#if 0
- __le32 intrstatus; /* interrupt status */
-#endif
-};
-
-struct rx_ring_info {
- struct sk_buff *skb;
- dma_addr_t mapping;
-};
-struct tx_ring_info {
- struct sk_buff *skb;
- dma_addr_t mapping;
- unsigned int used_slots;
-};
-
-#define PHY_CNT 2
-struct netdev_private {
- /* Descriptor rings first for alignment. */
- struct starfire_rx_desc *rx_ring;
- starfire_tx_desc *tx_ring;
- dma_addr_t rx_ring_dma;
- dma_addr_t tx_ring_dma;
- /* The addresses of rx/tx-in-place skbuffs. */
- struct rx_ring_info rx_info[RX_RING_SIZE];
- struct tx_ring_info tx_info[TX_RING_SIZE];
- /* Pointers to completion queues (full pages). */
- rx_done_desc *rx_done_q;
- dma_addr_t rx_done_q_dma;
- unsigned int rx_done;
- struct tx_done_desc *tx_done_q;
- dma_addr_t tx_done_q_dma;
- unsigned int tx_done;
- struct napi_struct napi;
- struct net_device *dev;
- struct pci_dev *pci_dev;
-#ifdef VLAN_SUPPORT
- unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)];
-#endif
- void *queue_mem;
- dma_addr_t queue_mem_dma;
- size_t queue_mem_size;
-
- /* Frequently used values: keep some adjacent for cache effect. */
- spinlock_t lock;
- unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
- unsigned int cur_tx, dirty_tx, reap_tx;
- unsigned int rx_buf_sz; /* Based on MTU+slack. */
- /* These values keep track of the transceiver/media in use. */
- int speed100; /* Set if speed == 100MBit. */
- u32 tx_mode;
- u32 intr_timer_ctrl;
- u8 tx_threshold;
- /* MII transceiver section. */
- struct mii_if_info mii_if; /* MII lib hooks/info */
- int phy_cnt; /* MII device addresses. */
- unsigned char phys[PHY_CNT]; /* MII device addresses. */
- void __iomem *base;
-};
-
-
-static int mdio_read(struct net_device *dev, int phy_id, int location);
-static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
-static int netdev_open(struct net_device *dev);
-static void check_duplex(struct net_device *dev);
-static void tx_timeout(struct net_device *dev);
-static void init_ring(struct net_device *dev);
-static netdev_tx_t start_tx(struct sk_buff *skb, struct net_device *dev);
-static irqreturn_t intr_handler(int irq, void *dev_instance);
-static void netdev_error(struct net_device *dev, int intr_status);
-static int __netdev_rx(struct net_device *dev, int *quota);
-static int netdev_poll(struct napi_struct *napi, int budget);
-static void refill_rx_ring(struct net_device *dev);
-static void netdev_error(struct net_device *dev, int intr_status);
-static void set_rx_mode(struct net_device *dev);
-static struct net_device_stats *get_stats(struct net_device *dev);
-static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static int netdev_close(struct net_device *dev);
-static void netdev_media_change(struct net_device *dev);
-static const struct ethtool_ops ethtool_ops;
-
-
-#ifdef VLAN_SUPPORT
-static void netdev_vlan_rx_add_vid(struct net_device *dev, unsigned short vid)
-{
- struct netdev_private *np = netdev_priv(dev);
-
- spin_lock(&np->lock);
- if (debug > 1)
- printk("%s: Adding vlanid %d to vlan filter\n", dev->name, vid);
- set_bit(vid, np->active_vlans);
- set_rx_mode(dev);
- spin_unlock(&np->lock);
-}
-
-static void netdev_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
-{
- struct netdev_private *np = netdev_priv(dev);
-
- spin_lock(&np->lock);
- if (debug > 1)
- printk("%s: removing vlanid %d from vlan filter\n", dev->name, vid);
- clear_bit(vid, np->active_vlans);
- set_rx_mode(dev);
- spin_unlock(&np->lock);
-}
-#endif /* VLAN_SUPPORT */
-
-
-static const struct net_device_ops netdev_ops = {
- .ndo_open = netdev_open,
- .ndo_stop = netdev_close,
- .ndo_start_xmit = start_tx,
- .ndo_tx_timeout = tx_timeout,
- .ndo_get_stats = get_stats,
- .ndo_set_multicast_list = &set_rx_mode,
- .ndo_do_ioctl = netdev_ioctl,
- .ndo_change_mtu = eth_change_mtu,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-#ifdef VLAN_SUPPORT
- .ndo_vlan_rx_add_vid = netdev_vlan_rx_add_vid,
- .ndo_vlan_rx_kill_vid = netdev_vlan_rx_kill_vid,
-#endif
-};
-
-static int __devinit starfire_init_one(struct pci_dev *pdev,
- const struct pci_device_id *ent)
-{
- struct netdev_private *np;
- int i, irq, option, chip_idx = ent->driver_data;
- struct net_device *dev;
- static int card_idx = -1;
- long ioaddr;
- void __iomem *base;
- int drv_flags, io_size;
- int boguscnt;
-
-/* when built into the kernel, we only print version if device is found */
-#ifndef MODULE
- static int printed_version;
- if (!printed_version++)
- printk(version);
-#endif
-
- card_idx++;
-
- if (pci_enable_device (pdev))
- return -EIO;
-
- ioaddr = pci_resource_start(pdev, 0);
- io_size = pci_resource_len(pdev, 0);
- if (!ioaddr || ((pci_resource_flags(pdev, 0) & IORESOURCE_MEM) == 0)) {
- printk(KERN_ERR DRV_NAME " %d: no PCI MEM resources, aborting\n", card_idx);
- return -ENODEV;
- }
-
- dev = alloc_etherdev(sizeof(*np));
- if (!dev) {
- printk(KERN_ERR DRV_NAME " %d: cannot alloc etherdev, aborting\n", card_idx);
- return -ENOMEM;
- }
- SET_NETDEV_DEV(dev, &pdev->dev);
-
- irq = pdev->irq;
-
- if (pci_request_regions (pdev, DRV_NAME)) {
- printk(KERN_ERR DRV_NAME " %d: cannot reserve PCI resources, aborting\n", card_idx);
- goto err_out_free_netdev;
- }
-
- base = ioremap(ioaddr, io_size);
- if (!base) {
- printk(KERN_ERR DRV_NAME " %d: cannot remap %#x @ %#lx, aborting\n",
- card_idx, io_size, ioaddr);
- goto err_out_free_res;
- }
-
- pci_set_master(pdev);
-
- /* enable MWI -- it vastly improves Rx performance on sparc64 */
- pci_try_set_mwi(pdev);
-
-#ifdef ZEROCOPY
- /* Starfire can do TCP/UDP checksumming */
- if (enable_hw_cksum)
- dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
-#endif /* ZEROCOPY */
-
-#ifdef VLAN_SUPPORT
- dev->features |= NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER;
-#endif /* VLAN_RX_KILL_VID */
-#ifdef ADDR_64BITS
- dev->features |= NETIF_F_HIGHDMA;
-#endif /* ADDR_64BITS */
-
- /* Serial EEPROM reads are hidden by the hardware. */
- for (i = 0; i < 6; i++)
- dev->dev_addr[i] = readb(base + EEPROMCtrl + 20 - i);
-
-#if ! defined(final_version) /* Dump the EEPROM contents during development. */
- if (debug > 4)
- for (i = 0; i < 0x20; i++)
- printk("%2.2x%s",
- (unsigned int)readb(base + EEPROMCtrl + i),
- i % 16 != 15 ? " " : "\n");
-#endif
-
- /* Issue soft reset */
- writel(MiiSoftReset, base + TxMode);
- udelay(1000);
- writel(0, base + TxMode);
-
- /* Reset the chip to erase previous misconfiguration. */
- writel(1, base + PCIDeviceConfig);
- boguscnt = 1000;
- while (--boguscnt > 0) {
- udelay(10);
- if ((readl(base + PCIDeviceConfig) & 1) == 0)
- break;
- }
- if (boguscnt == 0)
- printk("%s: chipset reset never completed!\n", dev->name);
- /* wait a little longer */
- udelay(1000);
-
- dev->base_addr = (unsigned long)base;
- dev->irq = irq;
-
- np = netdev_priv(dev);
- np->dev = dev;
- np->base = base;
- spin_lock_init(&np->lock);
- pci_set_drvdata(pdev, dev);
-
- np->pci_dev = pdev;
-
- np->mii_if.dev = dev;
- np->mii_if.mdio_read = mdio_read;
- np->mii_if.mdio_write = mdio_write;
- np->mii_if.phy_id_mask = 0x1f;
- np->mii_if.reg_num_mask = 0x1f;
-
- drv_flags = netdrv_tbl[chip_idx].drv_flags;
-
- option = card_idx < MAX_UNITS ? options[card_idx] : 0;
- if (dev->mem_start)
- option = dev->mem_start;
-
- /* The lower four bits are the media type. */
- if (option & 0x200)
- np->mii_if.full_duplex = 1;
-
- if (card_idx < MAX_UNITS && full_duplex[card_idx] > 0)
- np->mii_if.full_duplex = 1;
-
- if (np->mii_if.full_duplex)
- np->mii_if.force_media = 1;
- else
- np->mii_if.force_media = 0;
- np->speed100 = 1;
-
- /* timer resolution is 128 * 0.8us */
- np->intr_timer_ctrl = (((intr_latency * 10) / 1024) & IntrLatencyMask) |
- Timer10X | EnableIntrMasking;
-
- if (small_frames > 0) {
- np->intr_timer_ctrl |= SmallFrameBypass;
- switch (small_frames) {
- case 1 ... 64:
- np->intr_timer_ctrl |= SmallFrame64;
- break;
- case 65 ... 128:
- np->intr_timer_ctrl |= SmallFrame128;
- break;
- case 129 ... 256:
- np->intr_timer_ctrl |= SmallFrame256;
- break;
- default:
- np->intr_timer_ctrl |= SmallFrame512;
- if (small_frames > 512)
- printk("Adjusting small_frames down to 512\n");
- break;
- }
- }
-
- dev->netdev_ops = &netdev_ops;
- dev->watchdog_timeo = TX_TIMEOUT;
- SET_ETHTOOL_OPS(dev, ðtool_ops);
-
- netif_napi_add(dev, &np->napi, netdev_poll, max_interrupt_work);
-
- if (mtu)
- dev->mtu = mtu;
-
- if (register_netdev(dev))
- goto err_out_cleardev;
-
- printk(KERN_INFO "%s: %s at %p, %pM, IRQ %d.\n",
- dev->name, netdrv_tbl[chip_idx].name, base,
- dev->dev_addr, irq);
-
- if (drv_flags & CanHaveMII) {
- int phy, phy_idx = 0;
- int mii_status;
- for (phy = 0; phy < 32 && phy_idx < PHY_CNT; phy++) {
- mdio_write(dev, phy, MII_BMCR, BMCR_RESET);
- mdelay(100);
- boguscnt = 1000;
- while (--boguscnt > 0)
- if ((mdio_read(dev, phy, MII_BMCR) & BMCR_RESET) == 0)
- break;
- if (boguscnt == 0) {
- printk("%s: PHY#%d reset never completed!\n", dev->name, phy);
- continue;
- }
- mii_status = mdio_read(dev, phy, MII_BMSR);
- if (mii_status != 0) {
- np->phys[phy_idx++] = phy;
- np->mii_if.advertising = mdio_read(dev, phy, MII_ADVERTISE);
- printk(KERN_INFO "%s: MII PHY found at address %d, status "
- "%#4.4x advertising %#4.4x.\n",
- dev->name, phy, mii_status, np->mii_if.advertising);
- /* there can be only one PHY on-board */
- break;
- }
- }
- np->phy_cnt = phy_idx;
- if (np->phy_cnt > 0)
- np->mii_if.phy_id = np->phys[0];
- else
- memset(&np->mii_if, 0, sizeof(np->mii_if));
- }
-
- printk(KERN_INFO "%s: scatter-gather and hardware TCP cksumming %s.\n",
- dev->name, enable_hw_cksum ? "enabled" : "disabled");
- return 0;
-
-err_out_cleardev:
- pci_set_drvdata(pdev, NULL);
- iounmap(base);
-err_out_free_res:
- pci_release_regions (pdev);
-err_out_free_netdev:
- free_netdev(dev);
- return -ENODEV;
-}
-
-
-/* Read the MII Management Data I/O (MDIO) interfaces. */
-static int mdio_read(struct net_device *dev, int phy_id, int location)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *mdio_addr = np->base + MIICtrl + (phy_id<<7) + (location<<2);
- int result, boguscnt=1000;
- /* ??? Should we add a busy-wait here? */
- do {
- result = readl(mdio_addr);
- } while ((result & 0xC0000000) != 0x80000000 && --boguscnt > 0);
- if (boguscnt == 0)
- return 0;
- if ((result & 0xffff) == 0xffff)
- return 0;
- return result & 0xffff;
-}
-
-
-static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *mdio_addr = np->base + MIICtrl + (phy_id<<7) + (location<<2);
- writel(value, mdio_addr);
- /* The busy-wait will occur before a read. */
-}
-
-
-static int netdev_open(struct net_device *dev)
-{
- const struct firmware *fw_rx, *fw_tx;
- const __be32 *fw_rx_data, *fw_tx_data;
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
- int i, retval;
- size_t tx_size, rx_size;
- size_t tx_done_q_size, rx_done_q_size, tx_ring_size, rx_ring_size;
-
- /* Do we ever need to reset the chip??? */
-
- retval = request_irq(dev->irq, intr_handler, IRQF_SHARED, dev->name, dev);
- if (retval)
- return retval;
-
- /* Disable the Rx and Tx, and reset the chip. */
- writel(0, ioaddr + GenCtrl);
- writel(1, ioaddr + PCIDeviceConfig);
- if (debug > 1)
- printk(KERN_DEBUG "%s: netdev_open() irq %d.\n",
- dev->name, dev->irq);
-
- /* Allocate the various queues. */
- if (!np->queue_mem) {
- tx_done_q_size = ((sizeof(struct tx_done_desc) * DONE_Q_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
- rx_done_q_size = ((sizeof(rx_done_desc) * DONE_Q_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
- tx_ring_size = ((sizeof(starfire_tx_desc) * TX_RING_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
- rx_ring_size = sizeof(struct starfire_rx_desc) * RX_RING_SIZE;
- np->queue_mem_size = tx_done_q_size + rx_done_q_size + tx_ring_size + rx_ring_size;
- np->queue_mem = pci_alloc_consistent(np->pci_dev, np->queue_mem_size, &np->queue_mem_dma);
- if (np->queue_mem == NULL) {
- free_irq(dev->irq, dev);
- return -ENOMEM;
- }
-
- np->tx_done_q = np->queue_mem;
- np->tx_done_q_dma = np->queue_mem_dma;
- np->rx_done_q = (void *) np->tx_done_q + tx_done_q_size;
- np->rx_done_q_dma = np->tx_done_q_dma + tx_done_q_size;
- np->tx_ring = (void *) np->rx_done_q + rx_done_q_size;
- np->tx_ring_dma = np->rx_done_q_dma + rx_done_q_size;
- np->rx_ring = (void *) np->tx_ring + tx_ring_size;
- np->rx_ring_dma = np->tx_ring_dma + tx_ring_size;
- }
-
- /* Start with no carrier, it gets adjusted later */
- netif_carrier_off(dev);
- init_ring(dev);
- /* Set the size of the Rx buffers. */
- writel((np->rx_buf_sz << RxBufferLenShift) |
- (0 << RxMinDescrThreshShift) |
- RxPrefetchMode | RxVariableQ |
- RX_Q_ENTRIES |
- RX_DESC_Q_ADDR_SIZE | RX_DESC_ADDR_SIZE |
- RxDescSpace4,
- ioaddr + RxDescQCtrl);
-
- /* Set up the Rx DMA controller. */
- writel(RxChecksumIgnore |
- (0 << RxEarlyIntThreshShift) |
- (6 << RxHighPrioThreshShift) |
- ((DMA_BURST_SIZE / 32) << RxBurstSizeShift),
- ioaddr + RxDMACtrl);
-
- /* Set Tx descriptor */
- writel((2 << TxHiPriFIFOThreshShift) |
- (0 << TxPadLenShift) |
- ((DMA_BURST_SIZE / 32) << TxDMABurstSizeShift) |
- TX_DESC_Q_ADDR_SIZE |
- TX_DESC_SPACING | TX_DESC_TYPE,
- ioaddr + TxDescCtrl);
-
- writel( (np->queue_mem_dma >> 16) >> 16, ioaddr + RxDescQHiAddr);
- writel( (np->queue_mem_dma >> 16) >> 16, ioaddr + TxRingHiAddr);
- writel( (np->queue_mem_dma >> 16) >> 16, ioaddr + CompletionHiAddr);
- writel(np->rx_ring_dma, ioaddr + RxDescQAddr);
- writel(np->tx_ring_dma, ioaddr + TxRingPtr);
-
- writel(np->tx_done_q_dma, ioaddr + TxCompletionAddr);
- writel(np->rx_done_q_dma |
- RxComplType |
- (0 << RxComplThreshShift),
- ioaddr + RxCompletionAddr);
-
- if (debug > 1)
- printk(KERN_DEBUG "%s: Filling in the station address.\n", dev->name);
-
- /* Fill both the Tx SA register and the Rx perfect filter. */
- for (i = 0; i < 6; i++)
- writeb(dev->dev_addr[i], ioaddr + TxStationAddr + 5 - i);
- /* The first entry is special because it bypasses the VLAN filter.
- Don't use it. */
- writew(0, ioaddr + PerfFilterTable);
- writew(0, ioaddr + PerfFilterTable + 4);
- writew(0, ioaddr + PerfFilterTable + 8);
- for (i = 1; i < 16; i++) {
- __be16 *eaddrs = (__be16 *)dev->dev_addr;
- void __iomem *setup_frm = ioaddr + PerfFilterTable + i * 16;
- writew(be16_to_cpu(eaddrs[2]), setup_frm); setup_frm += 4;
- writew(be16_to_cpu(eaddrs[1]), setup_frm); setup_frm += 4;
- writew(be16_to_cpu(eaddrs[0]), setup_frm); setup_frm += 8;
- }
-
- /* Initialize other registers. */
- /* Configure the PCI bus bursts and FIFO thresholds. */
- np->tx_mode = TxFlowEnable|RxFlowEnable|PadEnable; /* modified when link is up. */
- writel(MiiSoftReset | np->tx_mode, ioaddr + TxMode);
- udelay(1000);
- writel(np->tx_mode, ioaddr + TxMode);
- np->tx_threshold = 4;
- writel(np->tx_threshold, ioaddr + TxThreshold);
-
- writel(np->intr_timer_ctrl, ioaddr + IntrTimerCtrl);
-
- napi_enable(&np->napi);
-
- netif_start_queue(dev);
-
- if (debug > 1)
- printk(KERN_DEBUG "%s: Setting the Rx and Tx modes.\n", dev->name);
- set_rx_mode(dev);
-
- np->mii_if.advertising = mdio_read(dev, np->phys[0], MII_ADVERTISE);
- check_duplex(dev);
-
- /* Enable GPIO interrupts on link change */
- writel(0x0f00ff00, ioaddr + GPIOCtrl);
-
- /* Set the interrupt mask */
- writel(IntrRxDone | IntrRxEmpty | IntrDMAErr |
- IntrTxDMADone | IntrStatsMax | IntrLinkChange |
- IntrRxGFPDead | IntrNoTxCsum | IntrTxBadID,
- ioaddr + IntrEnable);
- /* Enable PCI interrupts. */
- writel(0x00800000 | readl(ioaddr + PCIDeviceConfig),
- ioaddr + PCIDeviceConfig);
-
-#ifdef VLAN_SUPPORT
- /* Set VLAN type to 802.1q */
- writel(ETH_P_8021Q, ioaddr + VlanType);
-#endif /* VLAN_SUPPORT */
-
- retval = request_firmware(&fw_rx, FIRMWARE_RX, &np->pci_dev->dev);
- if (retval) {
- printk(KERN_ERR "starfire: Failed to load firmware \"%s\"\n",
- FIRMWARE_RX);
- goto out_init;
- }
- if (fw_rx->size % 4) {
- printk(KERN_ERR "starfire: bogus length %zu in \"%s\"\n",
- fw_rx->size, FIRMWARE_RX);
- retval = -EINVAL;
- goto out_rx;
- }
- retval = request_firmware(&fw_tx, FIRMWARE_TX, &np->pci_dev->dev);
- if (retval) {
- printk(KERN_ERR "starfire: Failed to load firmware \"%s\"\n",
- FIRMWARE_TX);
- goto out_rx;
- }
- if (fw_tx->size % 4) {
- printk(KERN_ERR "starfire: bogus length %zu in \"%s\"\n",
- fw_tx->size, FIRMWARE_TX);
- retval = -EINVAL;
- goto out_tx;
- }
- fw_rx_data = (const __be32 *)&fw_rx->data[0];
- fw_tx_data = (const __be32 *)&fw_tx->data[0];
- rx_size = fw_rx->size / 4;
- tx_size = fw_tx->size / 4;
-
- /* Load Rx/Tx firmware into the frame processors */
- for (i = 0; i < rx_size; i++)
- writel(be32_to_cpup(&fw_rx_data[i]), ioaddr + RxGfpMem + i * 4);
- for (i = 0; i < tx_size; i++)
- writel(be32_to_cpup(&fw_tx_data[i]), ioaddr + TxGfpMem + i * 4);
- if (enable_hw_cksum)
- /* Enable the Rx and Tx units, and the Rx/Tx frame processors. */
- writel(TxEnable|TxGFPEnable|RxEnable|RxGFPEnable, ioaddr + GenCtrl);
- else
- /* Enable the Rx and Tx units only. */
- writel(TxEnable|RxEnable, ioaddr + GenCtrl);
-
- if (debug > 1)
- printk(KERN_DEBUG "%s: Done netdev_open().\n",
- dev->name);
-
-out_tx:
- release_firmware(fw_tx);
-out_rx:
- release_firmware(fw_rx);
-out_init:
- if (retval)
- netdev_close(dev);
- return retval;
-}
-
-
-static void check_duplex(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- u16 reg0;
- int silly_count = 1000;
-
- mdio_write(dev, np->phys[0], MII_ADVERTISE, np->mii_if.advertising);
- mdio_write(dev, np->phys[0], MII_BMCR, BMCR_RESET);
- udelay(500);
- while (--silly_count && mdio_read(dev, np->phys[0], MII_BMCR) & BMCR_RESET)
- /* do nothing */;
- if (!silly_count) {
- printk("%s: MII reset failed!\n", dev->name);
- return;
- }
-
- reg0 = mdio_read(dev, np->phys[0], MII_BMCR);
-
- if (!np->mii_if.force_media) {
- reg0 |= BMCR_ANENABLE | BMCR_ANRESTART;
- } else {
- reg0 &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
- if (np->speed100)
- reg0 |= BMCR_SPEED100;
- if (np->mii_if.full_duplex)
- reg0 |= BMCR_FULLDPLX;
- printk(KERN_DEBUG "%s: Link forced to %sMbit %s-duplex\n",
- dev->name,
- np->speed100 ? "100" : "10",
- np->mii_if.full_duplex ? "full" : "half");
- }
- mdio_write(dev, np->phys[0], MII_BMCR, reg0);
-}
-
-
-static void tx_timeout(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
- int old_debug;
-
- printk(KERN_WARNING "%s: Transmit timed out, status %#8.8x, "
- "resetting...\n", dev->name, (int) readl(ioaddr + IntrStatus));
-
- /* Perhaps we should reinitialize the hardware here. */
-
- /*
- * Stop and restart the interface.
- * Cheat and increase the debug level temporarily.
- */
- old_debug = debug;
- debug = 2;
- netdev_close(dev);
- netdev_open(dev);
- debug = old_debug;
-
- /* Trigger an immediate transmit demand. */
-
- dev->trans_start = jiffies; /* prevent tx timeout */
- dev->stats.tx_errors++;
- netif_wake_queue(dev);
-}
-
-
-/* Initialize the Rx and Tx rings, along with various 'dev' bits. */
-static void init_ring(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- int i;
-
- np->cur_rx = np->cur_tx = np->reap_tx = 0;
- np->dirty_rx = np->dirty_tx = np->rx_done = np->tx_done = 0;
-
- np->rx_buf_sz = (dev->mtu <= 1500 ? PKT_BUF_SZ : dev->mtu + 32);
-
- /* Fill in the Rx buffers. Handle allocation failure gracefully. */
- for (i = 0; i < RX_RING_SIZE; i++) {
- struct sk_buff *skb = dev_alloc_skb(np->rx_buf_sz);
- np->rx_info[i].skb = skb;
- if (skb == NULL)
- break;
- np->rx_info[i].mapping = pci_map_single(np->pci_dev, skb->data, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
- skb->dev = dev; /* Mark as being used by this device. */
- /* Grrr, we cannot offset to correctly align the IP header. */
- np->rx_ring[i].rxaddr = cpu_to_dma(np->rx_info[i].mapping | RxDescValid);
- }
- writew(i - 1, np->base + RxDescQIdx);
- np->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
-
- /* Clear the remainder of the Rx buffer ring. */
- for ( ; i < RX_RING_SIZE; i++) {
- np->rx_ring[i].rxaddr = 0;
- np->rx_info[i].skb = NULL;
- np->rx_info[i].mapping = 0;
- }
- /* Mark the last entry as wrapping the ring. */
- np->rx_ring[RX_RING_SIZE - 1].rxaddr |= cpu_to_dma(RxDescEndRing);
-
- /* Clear the completion rings. */
- for (i = 0; i < DONE_Q_SIZE; i++) {
- np->rx_done_q[i].status = 0;
- np->tx_done_q[i].status = 0;
- }
-
- for (i = 0; i < TX_RING_SIZE; i++)
- memset(&np->tx_info[i], 0, sizeof(np->tx_info[i]));
-}
-
-
-static netdev_tx_t start_tx(struct sk_buff *skb, struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- unsigned int entry;
- u32 status;
- int i;
-
- /*
- * be cautious here, wrapping the queue has weird semantics
- * and we may not have enough slots even when it seems we do.
- */
- if ((np->cur_tx - np->dirty_tx) + skb_num_frags(skb) * 2 > TX_RING_SIZE) {
- netif_stop_queue(dev);
- return NETDEV_TX_BUSY;
- }
-
-#if defined(ZEROCOPY) && defined(HAS_BROKEN_FIRMWARE)
- if (skb->ip_summed == CHECKSUM_PARTIAL) {
- if (skb_padto(skb, (skb->len + PADDING_MASK) & ~PADDING_MASK))
- return NETDEV_TX_OK;
- }
-#endif /* ZEROCOPY && HAS_BROKEN_FIRMWARE */
-
- entry = np->cur_tx % TX_RING_SIZE;
- for (i = 0; i < skb_num_frags(skb); i++) {
- int wrap_ring = 0;
- status = TxDescID;
-
- if (i == 0) {
- np->tx_info[entry].skb = skb;
- status |= TxCRCEn;
- if (entry >= TX_RING_SIZE - skb_num_frags(skb)) {
- status |= TxRingWrap;
- wrap_ring = 1;
- }
- if (np->reap_tx) {
- status |= TxDescIntr;
- np->reap_tx = 0;
- }
- if (skb->ip_summed == CHECKSUM_PARTIAL) {
- status |= TxCalTCP;
- dev->stats.tx_compressed++;
- }
- status |= skb_first_frag_len(skb) | (skb_num_frags(skb) << 16);
-
- np->tx_info[entry].mapping =
- pci_map_single(np->pci_dev, skb->data, skb_first_frag_len(skb), PCI_DMA_TODEVICE);
- } else {
- skb_frag_t *this_frag = &skb_shinfo(skb)->frags[i - 1];
- status |= this_frag->size;
- np->tx_info[entry].mapping =
- pci_map_single(np->pci_dev, page_address(this_frag->page) + this_frag->page_offset, this_frag->size, PCI_DMA_TODEVICE);
- }
-
- np->tx_ring[entry].addr = cpu_to_dma(np->tx_info[entry].mapping);
- np->tx_ring[entry].status = cpu_to_le32(status);
- if (debug > 3)
- printk(KERN_DEBUG "%s: Tx #%d/#%d slot %d status %#8.8x.\n",
- dev->name, np->cur_tx, np->dirty_tx,
- entry, status);
- if (wrap_ring) {
- np->tx_info[entry].used_slots = TX_RING_SIZE - entry;
- np->cur_tx += np->tx_info[entry].used_slots;
- entry = 0;
- } else {
- np->tx_info[entry].used_slots = 1;
- np->cur_tx += np->tx_info[entry].used_slots;
- entry++;
- }
- /* scavenge the tx descriptors twice per TX_RING_SIZE */
- if (np->cur_tx % (TX_RING_SIZE / 2) == 0)
- np->reap_tx = 1;
- }
-
- /* Non-x86: explicitly flush descriptor cache lines here. */
- /* Ensure all descriptors are written back before the transmit is
- initiated. - Jes */
- wmb();
-
- /* Update the producer index. */
- writel(entry * (sizeof(starfire_tx_desc) / 8), np->base + TxProducerIdx);
-
- /* 4 is arbitrary, but should be ok */
- if ((np->cur_tx - np->dirty_tx) + 4 > TX_RING_SIZE)
- netif_stop_queue(dev);
-
- return NETDEV_TX_OK;
-}
-
-
-/* The interrupt handler does all of the Rx thread work and cleans up
- after the Tx thread. */
-static irqreturn_t intr_handler(int irq, void *dev_instance)
-{
- struct net_device *dev = dev_instance;
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
- int boguscnt = max_interrupt_work;
- int consumer;
- int tx_status;
- int handled = 0;
-
- do {
- u32 intr_status = readl(ioaddr + IntrClear);
-
- if (debug > 4)
- printk(KERN_DEBUG "%s: Interrupt status %#8.8x.\n",
- dev->name, intr_status);
-
- if (intr_status == 0 || intr_status == (u32) -1)
- break;
-
- handled = 1;
-
- if (intr_status & (IntrRxDone | IntrRxEmpty)) {
- u32 enable;
-
- if (likely(napi_schedule_prep(&np->napi))) {
- __napi_schedule(&np->napi);
- enable = readl(ioaddr + IntrEnable);
- enable &= ~(IntrRxDone | IntrRxEmpty);
- writel(enable, ioaddr + IntrEnable);
- /* flush PCI posting buffers */
- readl(ioaddr + IntrEnable);
- } else {
- /* Paranoia check */
- enable = readl(ioaddr + IntrEnable);
- if (enable & (IntrRxDone | IntrRxEmpty)) {
- printk(KERN_INFO
- "%s: interrupt while in poll!\n",
- dev->name);
- enable &= ~(IntrRxDone | IntrRxEmpty);
- writel(enable, ioaddr + IntrEnable);
- }
- }
- }
-
- /* Scavenge the skbuff list based on the Tx-done queue.
- There are redundant checks here that may be cleaned up
- after the driver has proven to be reliable. */
- consumer = readl(ioaddr + TxConsumerIdx);
- if (debug > 3)
- printk(KERN_DEBUG "%s: Tx Consumer index is %d.\n",
- dev->name, consumer);
-
- while ((tx_status = le32_to_cpu(np->tx_done_q[np->tx_done].status)) != 0) {
- if (debug > 3)
- printk(KERN_DEBUG "%s: Tx completion #%d entry %d is %#8.8x.\n",
- dev->name, np->dirty_tx, np->tx_done, tx_status);
- if ((tx_status & 0xe0000000) == 0xa0000000) {
- dev->stats.tx_packets++;
- } else if ((tx_status & 0xe0000000) == 0x80000000) {
- u16 entry = (tx_status & 0x7fff) / sizeof(starfire_tx_desc);
- struct sk_buff *skb = np->tx_info[entry].skb;
- np->tx_info[entry].skb = NULL;
- pci_unmap_single(np->pci_dev,
- np->tx_info[entry].mapping,
- skb_first_frag_len(skb),
- PCI_DMA_TODEVICE);
- np->tx_info[entry].mapping = 0;
- np->dirty_tx += np->tx_info[entry].used_slots;
- entry = (entry + np->tx_info[entry].used_slots) % TX_RING_SIZE;
- {
- int i;
- for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
- pci_unmap_single(np->pci_dev,
- np->tx_info[entry].mapping,
- skb_shinfo(skb)->frags[i].size,
- PCI_DMA_TODEVICE);
- np->dirty_tx++;
- entry++;
- }
- }
-
- dev_kfree_skb_irq(skb);
- }
- np->tx_done_q[np->tx_done].status = 0;
- np->tx_done = (np->tx_done + 1) % DONE_Q_SIZE;
- }
- writew(np->tx_done, ioaddr + CompletionQConsumerIdx + 2);
-
- if (netif_queue_stopped(dev) &&
- (np->cur_tx - np->dirty_tx + 4 < TX_RING_SIZE)) {
- /* The ring is no longer full, wake the queue. */
- netif_wake_queue(dev);
- }
-
- /* Stats overflow */
- if (intr_status & IntrStatsMax)
- get_stats(dev);
-
- /* Media change interrupt. */
- if (intr_status & IntrLinkChange)
- netdev_media_change(dev);
-
- /* Abnormal error summary/uncommon events handlers. */
- if (intr_status & IntrAbnormalSummary)
- netdev_error(dev, intr_status);
-
- if (--boguscnt < 0) {
- if (debug > 1)
- printk(KERN_WARNING "%s: Too much work at interrupt, "
- "status=%#8.8x.\n",
- dev->name, intr_status);
- break;
- }
- } while (1);
-
- if (debug > 4)
- printk(KERN_DEBUG "%s: exiting interrupt, status=%#8.8x.\n",
- dev->name, (int) readl(ioaddr + IntrStatus));
- return IRQ_RETVAL(handled);
-}
-
-
-/*
- * This routine is logically part of the interrupt/poll handler, but separated
- * for clarity and better register allocation.
- */
-static int __netdev_rx(struct net_device *dev, int *quota)
-{
- struct netdev_private *np = netdev_priv(dev);
- u32 desc_status;
- int retcode = 0;
-
- /* If EOP is set on the next entry, it's a new packet. Send it up. */
- while ((desc_status = le32_to_cpu(np->rx_done_q[np->rx_done].status)) != 0) {
- struct sk_buff *skb;
- u16 pkt_len;
- int entry;
- rx_done_desc *desc = &np->rx_done_q[np->rx_done];
-
- if (debug > 4)
- printk(KERN_DEBUG " netdev_rx() status of %d was %#8.8x.\n", np->rx_done, desc_status);
- if (!(desc_status & RxOK)) {
- /* There was an error. */
- if (debug > 2)
- printk(KERN_DEBUG " netdev_rx() Rx error was %#8.8x.\n", desc_status);
- dev->stats.rx_errors++;
- if (desc_status & RxFIFOErr)
- dev->stats.rx_fifo_errors++;
- goto next_rx;
- }
-
- if (*quota <= 0) { /* out of rx quota */
- retcode = 1;
- goto out;
- }
- (*quota)--;
-
- pkt_len = desc_status; /* Implicitly Truncate */
- entry = (desc_status >> 16) & 0x7ff;
-
- if (debug > 4)
- printk(KERN_DEBUG " netdev_rx() normal Rx pkt length %d, quota %d.\n", pkt_len, *quota);
- /* Check if the packet is long enough to accept without copying
- to a minimally-sized skbuff. */
- if (pkt_len < rx_copybreak &&
- (skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
- skb_reserve(skb, 2); /* 16 byte align the IP header */
- pci_dma_sync_single_for_cpu(np->pci_dev,
- np->rx_info[entry].mapping,
- pkt_len, PCI_DMA_FROMDEVICE);
- skb_copy_to_linear_data(skb, np->rx_info[entry].skb->data, pkt_len);
- pci_dma_sync_single_for_device(np->pci_dev,
- np->rx_info[entry].mapping,
- pkt_len, PCI_DMA_FROMDEVICE);
- skb_put(skb, pkt_len);
- } else {
- pci_unmap_single(np->pci_dev, np->rx_info[entry].mapping, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
- skb = np->rx_info[entry].skb;
- skb_put(skb, pkt_len);
- np->rx_info[entry].skb = NULL;
- np->rx_info[entry].mapping = 0;
- }
-#ifndef final_version /* Remove after testing. */
- /* You will want this info for the initial debug. */
- if (debug > 5) {
- printk(KERN_DEBUG " Rx data %pM %pM %2.2x%2.2x.\n",
- skb->data, skb->data + 6,
- skb->data[12], skb->data[13]);
- }
-#endif
-
- skb->protocol = eth_type_trans(skb, dev);
-#ifdef VLAN_SUPPORT
- if (debug > 4)
- printk(KERN_DEBUG " netdev_rx() status2 of %d was %#4.4x.\n", np->rx_done, le16_to_cpu(desc->status2));
-#endif
- if (le16_to_cpu(desc->status2) & 0x0100) {
- skb->ip_summed = CHECKSUM_UNNECESSARY;
- dev->stats.rx_compressed++;
- }
- /*
- * This feature doesn't seem to be working, at least
- * with the two firmware versions I have. If the GFP sees
- * an IP fragment, it either ignores it completely, or reports
- * "bad checksum" on it.
- *
- * Maybe I missed something -- corrections are welcome.
- * Until then, the printk stays. :-) -Ion
- */
- else if (le16_to_cpu(desc->status2) & 0x0040) {
- skb->ip_summed = CHECKSUM_COMPLETE;
- skb->csum = le16_to_cpu(desc->csum);
- printk(KERN_DEBUG "%s: checksum_hw, status2 = %#x\n", dev->name, le16_to_cpu(desc->status2));
- }
-#ifdef VLAN_SUPPORT
- if (le16_to_cpu(desc->status2) & 0x0200) {
- u16 vlid = le16_to_cpu(desc->vlanid);
-
- if (debug > 4) {
- printk(KERN_DEBUG " netdev_rx() vlanid = %d\n",
- vlid);
- }
- __vlan_hwaccel_put_tag(skb, vlid);
- }
-#endif /* VLAN_SUPPORT */
- netif_receive_skb(skb);
- dev->stats.rx_packets++;
-
- next_rx:
- np->cur_rx++;
- desc->status = 0;
- np->rx_done = (np->rx_done + 1) % DONE_Q_SIZE;
- }
-
- if (*quota == 0) { /* out of rx quota */
- retcode = 1;
- goto out;
- }
- writew(np->rx_done, np->base + CompletionQConsumerIdx);
-
- out:
- refill_rx_ring(dev);
- if (debug > 5)
- printk(KERN_DEBUG " exiting netdev_rx(): %d, status of %d was %#8.8x.\n",
- retcode, np->rx_done, desc_status);
- return retcode;
-}
-
-static int netdev_poll(struct napi_struct *napi, int budget)
-{
- struct netdev_private *np = container_of(napi, struct netdev_private, napi);
- struct net_device *dev = np->dev;
- u32 intr_status;
- void __iomem *ioaddr = np->base;
- int quota = budget;
-
- do {
- writel(IntrRxDone | IntrRxEmpty, ioaddr + IntrClear);
-
- if (__netdev_rx(dev, "a))
- goto out;
-
- intr_status = readl(ioaddr + IntrStatus);
- } while (intr_status & (IntrRxDone | IntrRxEmpty));
-
- napi_complete(napi);
- intr_status = readl(ioaddr + IntrEnable);
- intr_status |= IntrRxDone | IntrRxEmpty;
- writel(intr_status, ioaddr + IntrEnable);
-
- out:
- if (debug > 5)
- printk(KERN_DEBUG " exiting netdev_poll(): %d.\n",
- budget - quota);
-
- /* Restart Rx engine if stopped. */
- return budget - quota;
-}
-
-static void refill_rx_ring(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- struct sk_buff *skb;
- int entry = -1;
-
- /* Refill the Rx ring buffers. */
- for (; np->cur_rx - np->dirty_rx > 0; np->dirty_rx++) {
- entry = np->dirty_rx % RX_RING_SIZE;
- if (np->rx_info[entry].skb == NULL) {
- skb = dev_alloc_skb(np->rx_buf_sz);
- np->rx_info[entry].skb = skb;
- if (skb == NULL)
- break; /* Better luck next round. */
- np->rx_info[entry].mapping =
- pci_map_single(np->pci_dev, skb->data, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
- skb->dev = dev; /* Mark as being used by this device. */
- np->rx_ring[entry].rxaddr =
- cpu_to_dma(np->rx_info[entry].mapping | RxDescValid);
- }
- if (entry == RX_RING_SIZE - 1)
- np->rx_ring[entry].rxaddr |= cpu_to_dma(RxDescEndRing);
- }
- if (entry >= 0)
- writew(entry, np->base + RxDescQIdx);
-}
-
-
-static void netdev_media_change(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
- u16 reg0, reg1, reg4, reg5;
- u32 new_tx_mode;
- u32 new_intr_timer_ctrl;
-
- /* reset status first */
- mdio_read(dev, np->phys[0], MII_BMCR);
- mdio_read(dev, np->phys[0], MII_BMSR);
-
- reg0 = mdio_read(dev, np->phys[0], MII_BMCR);
- reg1 = mdio_read(dev, np->phys[0], MII_BMSR);
-
- if (reg1 & BMSR_LSTATUS) {
- /* link is up */
- if (reg0 & BMCR_ANENABLE) {
- /* autonegotiation is enabled */
- reg4 = mdio_read(dev, np->phys[0], MII_ADVERTISE);
- reg5 = mdio_read(dev, np->phys[0], MII_LPA);
- if (reg4 & ADVERTISE_100FULL && reg5 & LPA_100FULL) {
- np->speed100 = 1;
- np->mii_if.full_duplex = 1;
- } else if (reg4 & ADVERTISE_100HALF && reg5 & LPA_100HALF) {
- np->speed100 = 1;
- np->mii_if.full_duplex = 0;
- } else if (reg4 & ADVERTISE_10FULL && reg5 & LPA_10FULL) {
- np->speed100 = 0;
- np->mii_if.full_duplex = 1;
- } else {
- np->speed100 = 0;
- np->mii_if.full_duplex = 0;
- }
- } else {
- /* autonegotiation is disabled */
- if (reg0 & BMCR_SPEED100)
- np->speed100 = 1;
- else
- np->speed100 = 0;
- if (reg0 & BMCR_FULLDPLX)
- np->mii_if.full_duplex = 1;
- else
- np->mii_if.full_duplex = 0;
- }
- netif_carrier_on(dev);
- printk(KERN_DEBUG "%s: Link is up, running at %sMbit %s-duplex\n",
- dev->name,
- np->speed100 ? "100" : "10",
- np->mii_if.full_duplex ? "full" : "half");
-
- new_tx_mode = np->tx_mode & ~FullDuplex; /* duplex setting */
- if (np->mii_if.full_duplex)
- new_tx_mode |= FullDuplex;
- if (np->tx_mode != new_tx_mode) {
- np->tx_mode = new_tx_mode;
- writel(np->tx_mode | MiiSoftReset, ioaddr + TxMode);
- udelay(1000);
- writel(np->tx_mode, ioaddr + TxMode);
- }
-
- new_intr_timer_ctrl = np->intr_timer_ctrl & ~Timer10X;
- if (np->speed100)
- new_intr_timer_ctrl |= Timer10X;
- if (np->intr_timer_ctrl != new_intr_timer_ctrl) {
- np->intr_timer_ctrl = new_intr_timer_ctrl;
- writel(new_intr_timer_ctrl, ioaddr + IntrTimerCtrl);
- }
- } else {
- netif_carrier_off(dev);
- printk(KERN_DEBUG "%s: Link is down\n", dev->name);
- }
-}
-
-
-static void netdev_error(struct net_device *dev, int intr_status)
-{
- struct netdev_private *np = netdev_priv(dev);
-
- /* Came close to underrunning the Tx FIFO, increase threshold. */
- if (intr_status & IntrTxDataLow) {
- if (np->tx_threshold <= PKT_BUF_SZ / 16) {
- writel(++np->tx_threshold, np->base + TxThreshold);
- printk(KERN_NOTICE "%s: PCI bus congestion, increasing Tx FIFO threshold to %d bytes\n",
- dev->name, np->tx_threshold * 16);
- } else
- printk(KERN_WARNING "%s: PCI Tx underflow -- adapter is probably malfunctioning\n", dev->name);
- }
- if (intr_status & IntrRxGFPDead) {
- dev->stats.rx_fifo_errors++;
- dev->stats.rx_errors++;
- }
- if (intr_status & (IntrNoTxCsum | IntrDMAErr)) {
- dev->stats.tx_fifo_errors++;
- dev->stats.tx_errors++;
- }
- if ((intr_status & ~(IntrNormalMask | IntrAbnormalSummary | IntrLinkChange | IntrStatsMax | IntrTxDataLow | IntrRxGFPDead | IntrNoTxCsum | IntrPCIPad)) && debug)
- printk(KERN_ERR "%s: Something Wicked happened! %#8.8x.\n",
- dev->name, intr_status);
-}
-
-
-static struct net_device_stats *get_stats(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
-
- /* This adapter architecture needs no SMP locks. */
- dev->stats.tx_bytes = readl(ioaddr + 0x57010);
- dev->stats.rx_bytes = readl(ioaddr + 0x57044);
- dev->stats.tx_packets = readl(ioaddr + 0x57000);
- dev->stats.tx_aborted_errors =
- readl(ioaddr + 0x57024) + readl(ioaddr + 0x57028);
- dev->stats.tx_window_errors = readl(ioaddr + 0x57018);
- dev->stats.collisions =
- readl(ioaddr + 0x57004) + readl(ioaddr + 0x57008);
-
- /* The chip only need report frame silently dropped. */
- dev->stats.rx_dropped += readw(ioaddr + RxDMAStatus);
- writew(0, ioaddr + RxDMAStatus);
- dev->stats.rx_crc_errors = readl(ioaddr + 0x5703C);
- dev->stats.rx_frame_errors = readl(ioaddr + 0x57040);
- dev->stats.rx_length_errors = readl(ioaddr + 0x57058);
- dev->stats.rx_missed_errors = readl(ioaddr + 0x5707C);
-
- return &dev->stats;
-}
-
-#ifdef VLAN_SUPPORT
-static u32 set_vlan_mode(struct netdev_private *np)
-{
- u32 ret = VlanMode;
- u16 vid;
- void __iomem *filter_addr = np->base + HashTable + 8;
- int vlan_count = 0;
-
- for_each_set_bit(vid, np->active_vlans, VLAN_N_VID) {
- if (vlan_count == 32)
- break;
- writew(vid, filter_addr);
- filter_addr += 16;
- vlan_count++;
- }
- if (vlan_count == 32) {
- ret |= PerfectFilterVlan;
- while (vlan_count < 32) {
- writew(0, filter_addr);
- filter_addr += 16;
- vlan_count++;
- }
- }
- return ret;
-}
-#endif /* VLAN_SUPPORT */
-
-static void set_rx_mode(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
- u32 rx_mode = MinVLANPrio;
- struct netdev_hw_addr *ha;
- int i;
-
-#ifdef VLAN_SUPPORT
- rx_mode |= set_vlan_mode(np);
-#endif /* VLAN_SUPPORT */
-
- if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
- rx_mode |= AcceptAll;
- } else if ((netdev_mc_count(dev) > multicast_filter_limit) ||
- (dev->flags & IFF_ALLMULTI)) {
- /* Too many to match, or accept all multicasts. */
- rx_mode |= AcceptBroadcast|AcceptAllMulticast|PerfectFilter;
- } else if (netdev_mc_count(dev) <= 14) {
- /* Use the 16 element perfect filter, skip first two entries. */
- void __iomem *filter_addr = ioaddr + PerfFilterTable + 2 * 16;
- __be16 *eaddrs;
- netdev_for_each_mc_addr(ha, dev) {
- eaddrs = (__be16 *) ha->addr;
- writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 4;
- writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
- writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 8;
- }
- eaddrs = (__be16 *)dev->dev_addr;
- i = netdev_mc_count(dev) + 2;
- while (i++ < 16) {
- writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 4;
- writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
- writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 8;
- }
- rx_mode |= AcceptBroadcast|PerfectFilter;
- } else {
- /* Must use a multicast hash table. */
- void __iomem *filter_addr;
- __be16 *eaddrs;
- __le16 mc_filter[32] __attribute__ ((aligned(sizeof(long)))); /* Multicast hash filter */
-
- memset(mc_filter, 0, sizeof(mc_filter));
- netdev_for_each_mc_addr(ha, dev) {
- /* The chip uses the upper 9 CRC bits
- as index into the hash table */
- int bit_nr = ether_crc_le(ETH_ALEN, ha->addr) >> 23;
- __le32 *fptr = (__le32 *) &mc_filter[(bit_nr >> 4) & ~1];
-
- *fptr |= cpu_to_le32(1 << (bit_nr & 31));
- }
- /* Clear the perfect filter list, skip first two entries. */
- filter_addr = ioaddr + PerfFilterTable + 2 * 16;
- eaddrs = (__be16 *)dev->dev_addr;
- for (i = 2; i < 16; i++) {
- writew(be16_to_cpu(eaddrs[0]), filter_addr); filter_addr += 4;
- writew(be16_to_cpu(eaddrs[1]), filter_addr); filter_addr += 4;
- writew(be16_to_cpu(eaddrs[2]), filter_addr); filter_addr += 8;
- }
- for (filter_addr = ioaddr + HashTable, i = 0; i < 32; filter_addr+= 16, i++)
- writew(mc_filter[i], filter_addr);
- rx_mode |= AcceptBroadcast|PerfectFilter|HashFilter;
- }
- writel(rx_mode, ioaddr + RxFilterMode);
-}
-
-static int check_if_running(struct net_device *dev)
-{
- if (!netif_running(dev))
- return -EINVAL;
- return 0;
-}
-
-static void get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
-{
- struct netdev_private *np = netdev_priv(dev);
- strcpy(info->driver, DRV_NAME);
- strcpy(info->version, DRV_VERSION);
- strcpy(info->bus_info, pci_name(np->pci_dev));
-}
-
-static int get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
- struct netdev_private *np = netdev_priv(dev);
- spin_lock_irq(&np->lock);
- mii_ethtool_gset(&np->mii_if, ecmd);
- spin_unlock_irq(&np->lock);
- return 0;
-}
-
-static int set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
- struct netdev_private *np = netdev_priv(dev);
- int res;
- spin_lock_irq(&np->lock);
- res = mii_ethtool_sset(&np->mii_if, ecmd);
- spin_unlock_irq(&np->lock);
- check_duplex(dev);
- return res;
-}
-
-static int nway_reset(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- return mii_nway_restart(&np->mii_if);
-}
-
-static u32 get_link(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- return mii_link_ok(&np->mii_if);
-}
-
-static u32 get_msglevel(struct net_device *dev)
-{
- return debug;
-}
-
-static void set_msglevel(struct net_device *dev, u32 val)
-{
- debug = val;
-}
-
-static const struct ethtool_ops ethtool_ops = {
- .begin = check_if_running,
- .get_drvinfo = get_drvinfo,
- .get_settings = get_settings,
- .set_settings = set_settings,
- .nway_reset = nway_reset,
- .get_link = get_link,
- .get_msglevel = get_msglevel,
- .set_msglevel = set_msglevel,
-};
-
-static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
- struct netdev_private *np = netdev_priv(dev);
- struct mii_ioctl_data *data = if_mii(rq);
- int rc;
-
- if (!netif_running(dev))
- return -EINVAL;
-
- spin_lock_irq(&np->lock);
- rc = generic_mii_ioctl(&np->mii_if, data, cmd, NULL);
- spin_unlock_irq(&np->lock);
-
- if ((cmd == SIOCSMIIREG) && (data->phy_id == np->phys[0]))
- check_duplex(dev);
-
- return rc;
-}
-
-static int netdev_close(struct net_device *dev)
-{
- struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->base;
- int i;
-
- netif_stop_queue(dev);
-
- napi_disable(&np->napi);
-
- if (debug > 1) {
- printk(KERN_DEBUG "%s: Shutting down ethercard, Intr status %#8.8x.\n",
- dev->name, (int) readl(ioaddr + IntrStatus));
- printk(KERN_DEBUG "%s: Queue pointers were Tx %d / %d, Rx %d / %d.\n",
- dev->name, np->cur_tx, np->dirty_tx,
- np->cur_rx, np->dirty_rx);
- }
-
- /* Disable interrupts by clearing the interrupt mask. */
- writel(0, ioaddr + IntrEnable);
-
- /* Stop the chip's Tx and Rx processes. */
- writel(0, ioaddr + GenCtrl);
- readl(ioaddr + GenCtrl);
-
- if (debug > 5) {
- printk(KERN_DEBUG" Tx ring at %#llx:\n",
- (long long) np->tx_ring_dma);
- for (i = 0; i < 8 /* TX_RING_SIZE is huge! */; i++)
- printk(KERN_DEBUG " #%d desc. %#8.8x %#llx -> %#8.8x.\n",
- i, le32_to_cpu(np->tx_ring[i].status),
- (long long) dma_to_cpu(np->tx_ring[i].addr),
- le32_to_cpu(np->tx_done_q[i].status));
- printk(KERN_DEBUG " Rx ring at %#llx -> %p:\n",
- (long long) np->rx_ring_dma, np->rx_done_q);
- if (np->rx_done_q)
- for (i = 0; i < 8 /* RX_RING_SIZE */; i++) {
- printk(KERN_DEBUG " #%d desc. %#llx -> %#8.8x\n",
- i, (long long) dma_to_cpu(np->rx_ring[i].rxaddr), le32_to_cpu(np->rx_done_q[i].status));
- }
- }
-
- free_irq(dev->irq, dev);
-
- /* Free all the skbuffs in the Rx queue. */
- for (i = 0; i < RX_RING_SIZE; i++) {
- np->rx_ring[i].rxaddr = cpu_to_dma(0xBADF00D0); /* An invalid address. */
- if (np->rx_info[i].skb != NULL) {
- pci_unmap_single(np->pci_dev, np->rx_info[i].mapping, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
- dev_kfree_skb(np->rx_info[i].skb);
- }
- np->rx_info[i].skb = NULL;
- np->rx_info[i].mapping = 0;
- }
- for (i = 0; i < TX_RING_SIZE; i++) {
- struct sk_buff *skb = np->tx_info[i].skb;
- if (skb == NULL)
- continue;
- pci_unmap_single(np->pci_dev,
- np->tx_info[i].mapping,
- skb_first_frag_len(skb), PCI_DMA_TODEVICE);
- np->tx_info[i].mapping = 0;
- dev_kfree_skb(skb);
- np->tx_info[i].skb = NULL;
- }
-
- return 0;
-}
-
-#ifdef CONFIG_PM
-static int starfire_suspend(struct pci_dev *pdev, pm_message_t state)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
-
- if (netif_running(dev)) {
- netif_device_detach(dev);
- netdev_close(dev);
- }
-
- pci_save_state(pdev);
- pci_set_power_state(pdev, pci_choose_state(pdev,state));
-
- return 0;
-}
-
-static int starfire_resume(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
-
- pci_set_power_state(pdev, PCI_D0);
- pci_restore_state(pdev);
-
- if (netif_running(dev)) {
- netdev_open(dev);
- netif_device_attach(dev);
- }
-
- return 0;
-}
-#endif /* CONFIG_PM */
-
-
-static void __devexit starfire_remove_one (struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct netdev_private *np = netdev_priv(dev);
-
- BUG_ON(!dev);
-
- unregister_netdev(dev);
-
- if (np->queue_mem)
- pci_free_consistent(pdev, np->queue_mem_size, np->queue_mem, np->queue_mem_dma);
-
-
- /* XXX: add wakeup code -- requires firmware for MagicPacket */
- pci_set_power_state(pdev, PCI_D3hot); /* go to sleep in D3 mode */
- pci_disable_device(pdev);
-
- iounmap(np->base);
- pci_release_regions(pdev);
-
- pci_set_drvdata(pdev, NULL);
- free_netdev(dev); /* Will also free np!! */
-}
-
-
-static struct pci_driver starfire_driver = {
- .name = DRV_NAME,
- .probe = starfire_init_one,
- .remove = __devexit_p(starfire_remove_one),
-#ifdef CONFIG_PM
- .suspend = starfire_suspend,
- .resume = starfire_resume,
-#endif /* CONFIG_PM */
- .id_table = starfire_pci_tbl,
-};
-
-
-static int __init starfire_init (void)
-{
-/* when a module, this is printed whether or not devices are found in probe */
-#ifdef MODULE
- printk(version);
-
- printk(KERN_INFO DRV_NAME ": polling (NAPI) enabled\n");
-#endif
-
- BUILD_BUG_ON(sizeof(dma_addr_t) != sizeof(netdrv_addr_t));
-
- return pci_register_driver(&starfire_driver);
-}
-
-
-static void __exit starfire_cleanup (void)
-{
- pci_unregister_driver (&starfire_driver);
-}
-
-
-module_init(starfire_init);
-module_exit(starfire_cleanup);
-
-
-/*
- * Local variables:
- * c-basic-offset: 8
- * tab-width: 8
- * End:
- */
projects / firefly-linux-kernel-4.4.55.git / commitdiff