compatible = "renesas,armadillo800eva"
- BOCK-W
compatible = "renesas,bockw", "renesas,r8a7778"
- - BOCK-W - Reference Device Tree Implementation
- compatible = "renesas,bockw-reference", "renesas,r8a7778"
- Genmai (RTK772100BC00000BR)
compatible = "renesas,genmai", "renesas,r7s72100"
- Gose
compatible = "renesas,lager", "renesas,r8a7790"
- Marzen
compatible = "renesas,marzen", "renesas,r8a7779"
-
-Note: Reference Device Tree Implementations are temporary implementations
- to ease the migration from platform devices to Device Tree, and are
- intended to be removed in the future.
Optional properties:
- interrupts: Must contain a list of interrupt specifiers for memory
controller interrupts, if available.
- - interrupts-names: Must contain a list of interrupt names corresponding to
- the interrupts in the interrupts property, if available.
- Valid interrupt names are:
+ - interrupt-names: Must contain a list of interrupt names corresponding to
+ the interrupts in the interrupts property, if available.
+ Valid interrupt names are:
- "sec" (secure interrupt)
- "temp" (normal (temperature) interrupt)
- power-domains: Must contain a reference to the PM domain that the memory
found in include/linux/spi/pxa2xx_spi.h:
struct pxa2xx_spi_master {
- u32 clock_enable;
u16 num_chipselect;
u8 enable_dma;
};
-The "pxa2xx_spi_master.clock_enable" field is used to enable/disable the
-corresponding SSP peripheral block in the "Clock Enable Register (CKEN"). See
-the "PXA2xx Developer Manual" section "Clocks and Power Management".
-
The "pxa2xx_spi_master.num_chipselect" field is used to determine the number of
slave device (chips) attached to this SPI master.
};
static struct pxa2xx_spi_master pxa_nssp_master_info = {
- .clock_enable = CKEN_NSSP, /* NSSP Peripheral clock */
.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
.enable_dma = 1, /* Enables NSSP DMA */
};
F: arch/arm/boot/dts/r7s*
F: arch/arm/boot/dts/r8a*
F: arch/arm/boot/dts/sh*
-F: arch/arm/configs/bockw_defconfig
-F: arch/arm/configs/marzen_defconfig
F: arch/arm/configs/shmobile_defconfig
F: arch/arm/include/debug/renesas-scif.S
F: arch/arm/mach-shmobile/
help
Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
-config ARCH_SHMOBILE_LEGACY
- bool "Renesas ARM SoCs (non-multiplatform)"
- select ARCH_SHMOBILE
- select ARM_PATCH_PHYS_VIRT if MMU
- select CLKDEV_LOOKUP
- select CPU_V7
- select GENERIC_CLOCKEVENTS
- select HAVE_ARM_SCU if SMP
- select HAVE_ARM_TWD if SMP
- select HAVE_SMP
- select MIGHT_HAVE_CACHE_L2X0
- select MULTI_IRQ_HANDLER
- select NO_IOPORT_MAP
- select PINCTRL
- select PM_GENERIC_DOMAINS if PM
- select SH_CLK_CPG
- select SPARSE_IRQ
- help
- Support for Renesas ARM SoC platforms using a non-multiplatform
- kernel. This includes the SH-Mobile, R-Mobile, EMMA-Mobile, R-Car
- and RZ families.
-
config ARCH_RPC
bool "RiscPC"
depends on MMU
default 200 if ARCH_EBSA110 || ARCH_S3C24XX || \
ARCH_S5PV210 || ARCH_EXYNOS4
default 128 if SOC_AT91RM9200
- default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE_LEGACY
default 0
choice
source "mm/Kconfig"
config FORCE_MAX_ZONEORDER
- int "Maximum zone order" if ARCH_SHMOBILE_LEGACY
- range 11 64 if ARCH_SHMOBILE_LEGACY
+ int "Maximum zone order"
default "12" if SOC_AM33XX
default "9" if SA1111 || ARCH_EFM32
default "11"
config UNCOMPRESS_INCLUDE
string
default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \
- PLAT_SAMSUNG || ARM_SINGLE_ARMV7M || \
- ARCH_SHMOBILE_LEGACY
+ PLAT_SAMSUNG || ARM_SINGLE_ARMV7M
default "mach/uncompress.h"
config EARLY_PRINTK
s5pv210-smdkc110.dtb \
s5pv210-smdkv210.dtb \
s5pv210-torbreck.dtb
-dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
- r8a7778-bockw.dtb \
- r8a7778-bockw-reference.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
emev2-kzm9d.dtb \
r7s72100-genmai.dtb \
};
i2c@4000a000 {
- efm32,location = <3>;
+ energymicro,location = <3>;
status = "ok";
temp@48 {
spi0: spi@4000c000 { /* USART0 */
cs-gpios = <&gpio 68 1>; // E4
- location = <1>;
+ energymicro,location = <1>;
status = "ok";
microsd@0 {
spi1: spi@4000c400 { /* USART1 */
cs-gpios = <&gpio 51 1>; // D3
- location = <1>;
+ energymicro,location = <1>;
status = "ok";
ks8851@0 {
};
uart4: uart@4000e400 { /* UART1 */
- location = <2>;
+ energymicro,location = <2>;
status = "ok";
};
soc {
adc: adc@40002000 {
- compatible = "efm32,adc";
+ compatible = "energymicro,efm32-adc";
reg = <0x40002000 0x400>;
interrupts = <7>;
clocks = <&cmu clk_HFPERCLKADC0>;
};
gpio: gpio@40006000 {
- compatible = "efm32,gpio";
+ compatible = "energymicro,efm32-gpio";
reg = <0x40006000 0x1000>;
interrupts = <1 11>;
gpio-controller;
i2c0: i2c@4000a000 {
#address-cells = <1>;
#size-cells = <0>;
- compatible = "efm32,i2c";
+ compatible = "energymicro,efm32-i2c";
reg = <0x4000a000 0x400>;
interrupts = <9>;
clocks = <&cmu clk_HFPERCLKI2C0>;
i2c1: i2c@4000a400 {
#address-cells = <1>;
#size-cells = <0>;
- compatible = "efm32,i2c";
+ compatible = "energymicro,efm32-i2c";
reg = <0x4000a400 0x400>;
interrupts = <10>;
clocks = <&cmu clk_HFPERCLKI2C1>;
spi0: spi@4000c000 { /* USART0 */
#address-cells = <1>;
#size-cells = <0>;
- compatible = "efm32,spi";
+ compatible = "energymicro,efm32-spi";
reg = <0x4000c000 0x400>;
interrupts = <3 4>;
clocks = <&cmu clk_HFPERCLKUSART0>;
spi1: spi@4000c400 { /* USART1 */
#address-cells = <1>;
#size-cells = <0>;
- compatible = "efm32,spi";
+ compatible = "energymicro,efm32-spi";
reg = <0x4000c400 0x400>;
interrupts = <15 16>;
clocks = <&cmu clk_HFPERCLKUSART1>;
spi2: spi@4000c800 { /* USART2 */
#address-cells = <1>;
#size-cells = <0>;
- compatible = "efm32,spi";
+ compatible = "energymicro,efm32-spi";
reg = <0x4000c800 0x400>;
interrupts = <18 19>;
clocks = <&cmu clk_HFPERCLKUSART2>;
};
uart0: uart@4000c000 { /* USART0 */
- compatible = "efm32,uart";
+ compatible = "energymicro,efm32-uart";
reg = <0x4000c000 0x400>;
interrupts = <3 4>;
clocks = <&cmu clk_HFPERCLKUSART0>;
};
uart1: uart@4000c400 { /* USART1 */
- compatible = "efm32,uart";
+ compatible = "energymicro,efm32-uart";
reg = <0x4000c400 0x400>;
interrupts = <15 16>;
clocks = <&cmu clk_HFPERCLKUSART1>;
};
uart2: uart@4000c800 { /* USART2 */
- compatible = "efm32,uart";
+ compatible = "energymicro,efm32-uart";
reg = <0x4000c800 0x400>;
interrupts = <18 19>;
clocks = <&cmu clk_HFPERCLKUSART2>;
};
uart3: uart@4000e000 { /* UART0 */
- compatible = "efm32,uart";
+ compatible = "energymicro,efm32-uart";
reg = <0x4000e000 0x400>;
interrupts = <20 21>;
clocks = <&cmu clk_HFPERCLKUART0>;
};
uart4: uart@4000e400 { /* UART1 */
- compatible = "efm32,uart";
+ compatible = "energymicro,efm32-uart";
reg = <0x4000e400 0x400>;
interrupts = <22 23>;
clocks = <&cmu clk_HFPERCLKUART1>;
};
timer0: timer@40010000 {
- compatible = "efm32,timer";
+ compatible = "energymicro,efm32-timer";
reg = <0x40010000 0x400>;
interrupts = <2>;
clocks = <&cmu clk_HFPERCLKTIMER0>;
};
timer1: timer@40010400 {
- compatible = "efm32,timer";
+ compatible = "energymicro,efm32-timer";
reg = <0x40010400 0x400>;
interrupts = <12>;
clocks = <&cmu clk_HFPERCLKTIMER1>;
};
timer2: timer@40010800 {
- compatible = "efm32,timer";
+ compatible = "energymicro,efm32-timer";
reg = <0x40010800 0x400>;
interrupts = <13>;
clocks = <&cmu clk_HFPERCLKTIMER2>;
};
timer3: timer@40010c00 {
- compatible = "efm32,timer";
+ compatible = "energymicro,efm32-timer";
reg = <0x40010c00 0x400>;
interrupts = <14>;
clocks = <&cmu clk_HFPERCLKTIMER3>;
+++ /dev/null
-/*
- * Reference Device Tree Source for the Bock-W board
- *
- * Copyright (C) 2013 Renesas Solutions Corp.
- * Copyright (C) 2013 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * based on r8a7779
- *
- * Copyright (C) 2013 Renesas Solutions Corp.
- * Copyright (C) 2013 Simon Horman
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/dts-v1/;
-#include "r8a7778.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "bockw";
- compatible = "renesas,bockw-reference", "renesas,r8a7778";
-
- aliases {
- serial0 = &scif0;
- };
-
- chosen {
- bootargs = "ignore_loglevel root=/dev/nfs ip=dhcp rw";
- stdout-path = &scif0;
- };
-
- memory {
- device_type = "memory";
- reg = <0x60000000 0x10000000>;
- };
-
- fixedregulator3v3: fixedregulator@0 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ethernet@18300000 {
- compatible = "smsc,lan9220", "smsc,lan9115";
- reg = <0x18300000 0x1000>;
-
- phy-mode = "mii";
- interrupt-parent = <&irqpin>;
- interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
- reg-io-width = <4>;
- vddvario-supply = <&fixedregulator3v3>;
- vdd33a-supply = <&fixedregulator3v3>;
- };
-
-};
-
-&mmcif {
- pinctrl-0 = <&mmc_pins>;
- pinctrl-names = "default";
-
- vmmc-supply = <&fixedregulator3v3>;
- bus-width = <8>;
- broken-cd;
- status = "okay";
-};
-
-&irqpin {
- status = "okay";
-};
-
-&tmu0 {
- status = "okay";
-};
-
-&pfc {
- scif0_pins: serial0 {
- renesas,groups = "scif0_data_a", "scif0_ctrl";
- renesas,function = "scif0";
- };
-
- mmc_pins: mmc {
- renesas,groups = "mmc_data8", "mmc_ctrl";
- renesas,function = "mmc";
- };
-
- sdhi0_pins: sd0 {
- renesas,groups = "sdhi0_data4", "sdhi0_ctrl",
- "sdhi0_cd";
- renesas,function = "sdhi0";
- };
-
- hspi0_pins: hspi0 {
- renesas,groups = "hspi0_a";
- renesas,function = "hspi0";
- };
-};
-
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
-
- vmmc-supply = <&fixedregulator3v3>;
- bus-width = <4>;
- status = "okay";
- wp-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
-};
-
-&hspi0 {
- pinctrl-0 = <&hspi0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- flash: flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spansion,s25fl008k", "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <104000000>;
- m25p,fast-read;
-
- partition@0 {
- label = "data(spi)";
- reg = <0x00000000 0x00100000>;
- };
- };
-};
-
-&scif0 {
- pinctrl-0 = <&scif0_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
+++ /dev/null
-# CONFIG_ARM_PATCH_PHYS_VIRT is not set
-CONFIG_KERNEL_LZMA=y
-CONFIG_NO_HZ=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=16
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_R8A7778=y
-CONFIG_MACH_BOCKW=y
-CONFIG_MEMORY_START=0x60000000
-CONFIG_MEMORY_SIZE=0x10000000
-CONFIG_SHMOBILE_TIMER_HZ=1024
-# CONFIG_SH_TIMER_CMT is not set
-# CONFIG_EM_TIMER_STI is not set
-CONFIG_ARM_ERRATA_430973=y
-CONFIG_ARM_ERRATA_458693=y
-CONFIG_ARM_ERRATA_460075=y
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_VFP=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-# CONFIG_STANDALONE is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-# CONFIG_NET_CADENCE is not set
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_CIRRUS is not set
-# CONFIG_NET_VENDOR_FARADAY is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-# CONFIG_NET_VENDOR_SEEQ is not set
-CONFIG_SMSC911X=y
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_NET_VENDOR_WIZNET is not set
-# CONFIG_INPUT is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_DEVKMEM is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=6
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
-CONFIG_I2C=y
-CONFIG_I2C_RCAR=y
-CONFIG_GPIO_RCAR=y
-CONFIG_REGULATOR=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_MEDIA_CAMERA_SUPPORT=y
-CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_SOC_CAMERA=y
-CONFIG_VIDEO_RCAR_VIN=y
-# CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
-CONFIG_VIDEO_ML86V7667=y
-CONFIG_SPI=y
-CONFIG_SPI_SH_HSPI=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SOC=y
-CONFIG_SND_SOC_RCAR=y
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PLATFORM=y
-CONFIG_USB_EHCI_HCD_PLATFORM=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_RCAR_PHY=y
-CONFIG_MMC=y
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_RX8581=y
-CONFIG_DMADEVICES=y
-CONFIG_RCAR_HPB_DMAE=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV_GENIRQ=y
-# CONFIG_IOMMU_SUPPORT is not set
-# CONFIG_DNOTIFY is not set
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_SWAP=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_FTRACE is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_AVERAGE=y
return 0;
}
-void __ref psci_cpu_die(unsigned int cpu)
+void psci_cpu_die(unsigned int cpu)
{
u32 state = PSCI_POWER_STATE_TYPE_POWER_DOWN <<
PSCI_0_2_POWER_STATE_TYPE_SHIFT;
panic("psci: cpu %d failed to shutdown\n", cpu);
}
-int __ref psci_cpu_kill(unsigned int cpu)
+int psci_cpu_kill(unsigned int cpu)
{
int err, i;
#include <linux/cpu_pm.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/irqchip.h>
#include <linux/irqdomain.h>
#include <linux/of_address.h>
#include <linux/err.h>
return 0;
}
-#define EXYNOS_PMU_IRQ(symbol, name) OF_DECLARE_2(irqchip, symbol, name, exynos_pmu_irq_init)
+#define EXYNOS_PMU_IRQ(symbol, name) IRQCHIP_DECLARE(symbol, name, exynos_pmu_irq_init)
EXYNOS_PMU_IRQ(exynos3250_pmu_irq, "samsung,exynos3250-pmu");
EXYNOS_PMU_IRQ(exynos4210_pmu_irq, "samsung,exynos4210-pmu");
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/irqchip.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
return 0;
}
-
-/*
- * We cannot use the IRQCHIP_DECLARE macro that lives in
- * drivers/irqchip, so we're forced to roll our own. Not very nice.
- */
-OF_DECLARE_2(irqchip, imx_gpc, "fsl,imx6q-gpc", imx_gpc_init);
+IRQCHIP_DECLARE(imx_gpc, "fsl,imx6q-gpc", imx_gpc_init);
void __init imx_gpc_check_dt(void)
{
#include <linux/dma-mapping.h>
#include <linux/memblock.h>
#include <linux/mbus.h>
-#include <linux/signal.h>
#include <linux/slab.h>
#include <linux/irqchip.h>
#include <asm/hardware/cache-l2x0.h>
static void __init mvebu_memblock_reserve(void) {}
#endif
-/*
- * Early versions of Armada 375 SoC have a bug where the BootROM
- * leaves an external data abort pending. The kernel is hit by this
- * data abort as soon as it enters userspace, because it unmasks the
- * data aborts at this moment. We register a custom abort handler
- * below to ignore the first data abort to work around this
- * problem.
- */
-static int armada_375_external_abort_wa(unsigned long addr, unsigned int fsr,
- struct pt_regs *regs)
-{
- static int ignore_first;
-
- if (!ignore_first && fsr == 0x1406) {
- ignore_first = 1;
- return 0;
- }
-
- return 1;
-}
-
static void __init mvebu_init_irq(void)
{
irqchip_init();
BUG_ON(mvebu_mbus_dt_init(coherency_available()));
}
-static void __init external_abort_quirk(void)
-{
- u32 dev, rev;
-
- if (mvebu_get_soc_id(&dev, &rev) == 0 && rev > ARMADA_375_Z1_REV)
- return;
-
- hook_fault_code(16 + 6, armada_375_external_abort_wa, SIGBUS, 0,
- "imprecise external abort");
-}
-
static void __init i2c_quirk(void)
{
struct device_node *np;
{
if (of_machine_is_compatible("marvell,armadaxp"))
i2c_quirk();
- if (of_machine_is_compatible("marvell,a375-db"))
- external_abort_quirk();
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
/* Test the CR_C bit and set it if it was cleared */
asm volatile(
"mrc p15, 0, r0, c1, c0, 0 \n\t"
- "tst r0, #(1 << 2) \n\t"
+ "tst r0, %0 \n\t"
"orreq r0, r0, #(1 << 2) \n\t"
"mcreq p15, 0, r0, c1, c0, 0 \n\t"
"isb "
- : : : "r0");
+ : : "Ir" (CR_C) : "r0");
pr_debug("Failed to suspend the system\n");
Support for TI OMAP 850 F-Sample board. Say Y here if you have such
a board.
-config MACH_VOICEBLUE
- bool "Voiceblue"
- depends on ARCH_OMAP1 && ARCH_OMAP15XX
- help
- Support for Voiceblue GSM/VoIP gateway. Say Y here if you have
- such a board.
-
config MACH_OMAP_PALMTE
bool "Palm Tungsten E"
depends on ARCH_OMAP1 && ARCH_OMAP15XX
obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o board-h3-mmc.o \
board-nand.o
-obj-$(CONFIG_MACH_VOICEBLUE) += board-voiceblue.o
obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
obj-$(CONFIG_MACH_OMAP_PALMZ71) += board-palmz71.o
obj-$(CONFIG_MACH_OMAP_PALMTT) += board-palmtt.o
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap1/board-voiceblue.c
- *
- * Modified from board-generic.c
- *
- * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
- *
- * Code for OMAP5910 based VoiceBlue board (VoIP to GSM gateway).
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/mtd/physmap.h>
-#include <linux/notifier.h>
-#include <linux/reboot.h>
-#include <linux/serial_8250.h>
-#include <linux/serial_reg.h>
-#include <linux/smc91x.h>
-#include <linux/export.h>
-#include <linux/reboot.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <mach/board-voiceblue.h>
-#include <mach/flash.h>
-#include <mach/mux.h>
-#include <mach/tc.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
-#include "common.h"
-
-static struct plat_serial8250_port voiceblue_ports[] = {
- {
- .mapbase = (unsigned long)(OMAP_CS1_PHYS + 0x40000),
- .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
- .iotype = UPIO_MEM,
- .regshift = 1,
- .uartclk = 3686400,
- },
- {
- .mapbase = (unsigned long)(OMAP_CS1_PHYS + 0x50000),
- .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
- .iotype = UPIO_MEM,
- .regshift = 1,
- .uartclk = 3686400,
- },
- {
- .mapbase = (unsigned long)(OMAP_CS1_PHYS + 0x60000),
- .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
- .iotype = UPIO_MEM,
- .regshift = 1,
- .uartclk = 3686400,
- },
- {
- .mapbase = (unsigned long)(OMAP_CS1_PHYS + 0x70000),
- .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
- .iotype = UPIO_MEM,
- .regshift = 1,
- .uartclk = 3686400,
- },
- { },
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM1,
-};
-
-static int __init ext_uart_init(void)
-{
- if (!machine_is_voiceblue())
- return -ENODEV;
-
- voiceblue_ports[0].irq = gpio_to_irq(12);
- voiceblue_ports[1].irq = gpio_to_irq(13);
- voiceblue_ports[2].irq = gpio_to_irq(14);
- voiceblue_ports[3].irq = gpio_to_irq(15);
- serial_device.dev.platform_data = voiceblue_ports;
- return platform_device_register(&serial_device);
-}
-arch_initcall(ext_uart_init);
-
-static struct physmap_flash_data voiceblue_flash_data = {
- .width = 2,
- .set_vpp = omap1_set_vpp,
-};
-
-static struct resource voiceblue_flash_resource = {
- .start = OMAP_CS0_PHYS,
- .end = OMAP_CS0_PHYS + SZ_32M - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device voiceblue_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &voiceblue_flash_data,
- },
- .num_resources = 1,
- .resource = &voiceblue_flash_resource,
-};
-
-static struct smc91x_platdata voiceblue_smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource voiceblue_smc91x_resources[] = {
- [0] = {
- .start = OMAP_CS2_PHYS + 0x300,
- .end = OMAP_CS2_PHYS + 0x300 + 16,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
- },
-};
-
-static struct platform_device voiceblue_smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .dev = {
- .platform_data = &voiceblue_smc91x_info,
- },
- .num_resources = ARRAY_SIZE(voiceblue_smc91x_resources),
- .resource = voiceblue_smc91x_resources,
-};
-
-static struct platform_device *voiceblue_devices[] __initdata = {
- &voiceblue_flash_device,
- &voiceblue_smc91x_device,
-};
-
-static struct omap_usb_config voiceblue_usb_config __initdata = {
- .hmc_mode = 3,
- .register_host = 1,
- .register_dev = 1,
- .pins[0] = 2,
- .pins[1] = 6,
- .pins[2] = 6,
-};
-
-#define MACHINE_PANICED 1
-#define MACHINE_REBOOTING 2
-#define MACHINE_REBOOT 4
-static unsigned long machine_state;
-
-static int panic_event(struct notifier_block *this, unsigned long event,
- void *ptr)
-{
- if (test_and_set_bit(MACHINE_PANICED, &machine_state))
- return NOTIFY_DONE;
-
- /* Flash power LED */
- omap_writeb(0x78, OMAP_LPG1_LCR);
- omap_writeb(0x01, OMAP_LPG1_PMR); /* Enable clock */
-
- return NOTIFY_DONE;
-}
-
-static struct notifier_block panic_block = {
- .notifier_call = panic_event,
-};
-
-static int __init voiceblue_setup(void)
-{
- if (!machine_is_voiceblue())
- return -ENODEV;
-
- /* Setup panic notifier */
- atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
-
- return 0;
-}
-postcore_initcall(voiceblue_setup);
-
-static int wdt_gpio_state;
-
-void voiceblue_wdt_enable(void)
-{
- gpio_direction_output(0, 0);
- gpio_set_value(0, 1);
- gpio_set_value(0, 0);
- wdt_gpio_state = 0;
-}
-
-void voiceblue_wdt_disable(void)
-{
- gpio_set_value(0, 0);
- gpio_set_value(0, 1);
- gpio_set_value(0, 0);
- gpio_direction_input(0);
-}
-
-void voiceblue_wdt_ping(void)
-{
- if (test_bit(MACHINE_REBOOT, &machine_state))
- return;
-
- wdt_gpio_state = !wdt_gpio_state;
- gpio_set_value(0, wdt_gpio_state);
-}
-
-static void voiceblue_restart(enum reboot_mode mode, const char *cmd)
-{
- /*
- * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
- * "Global Software Reset Affects Traffic Controller Frequency".
- */
- if (cpu_is_omap5912()) {
- omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4), DPLL_CTL);
- omap_writew(0x8, ARM_RSTCT1);
- }
-
- set_bit(MACHINE_REBOOT, &machine_state);
- voiceblue_wdt_enable();
- while (1) ;
-}
-
-EXPORT_SYMBOL(voiceblue_wdt_enable);
-EXPORT_SYMBOL(voiceblue_wdt_disable);
-EXPORT_SYMBOL(voiceblue_wdt_ping);
-
-static void __init voiceblue_init(void)
-{
- /* mux pins for uarts */
- omap_cfg_reg(UART1_TX);
- omap_cfg_reg(UART1_RTS);
- omap_cfg_reg(UART2_TX);
- omap_cfg_reg(UART2_RTS);
- omap_cfg_reg(UART3_TX);
- omap_cfg_reg(UART3_RX);
-
- /* Watchdog */
- gpio_request(0, "Watchdog");
- /* smc91x reset */
- gpio_request(7, "SMC91x reset");
- gpio_direction_output(7, 1);
- udelay(2); /* wait at least 100ns */
- gpio_set_value(7, 0);
- mdelay(50); /* 50ms until PHY ready */
- /* smc91x interrupt pin */
- gpio_request(8, "SMC91x irq");
- /* 16C554 reset*/
- gpio_request(6, "16C554 reset");
- gpio_direction_output(6, 0);
- /* 16C554 interrupt pins */
- gpio_request(12, "16C554 irq");
- gpio_request(13, "16C554 irq");
- gpio_request(14, "16C554 irq");
- gpio_request(15, "16C554 irq");
- irq_set_irq_type(gpio_to_irq(12), IRQ_TYPE_EDGE_RISING);
- irq_set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
- irq_set_irq_type(gpio_to_irq(14), IRQ_TYPE_EDGE_RISING);
- irq_set_irq_type(gpio_to_irq(15), IRQ_TYPE_EDGE_RISING);
-
- voiceblue_smc91x_resources[1].start = gpio_to_irq(8);
- voiceblue_smc91x_resources[1].end = gpio_to_irq(8);
- platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
- omap_serial_init();
- omap1_usb_init(&voiceblue_usb_config);
- omap_register_i2c_bus(1, 100, NULL, 0);
-
- /* There is a good chance board is going up, so enable power LED
- * (it is connected through invertor) */
- omap_writeb(0x00, OMAP_LPG1_LCR);
- omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
-}
-
-MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
- /* Maintainer: Ladislav Michl <michl@2n.cz> */
- .atag_offset = 0x100,
- .map_io = omap15xx_map_io,
- .init_early = omap1_init_early,
- .init_irq = omap1_init_irq,
- .handle_irq = omap1_handle_irq,
- .init_machine = voiceblue_init,
- .init_late = omap1_init_late,
- .init_time = omap1_timer_init,
- .restart = voiceblue_restart,
-MACHINE_END
+++ /dev/null
-/*
- * Copyright (C) 2004 2N Telekomunikace, Ladislav Michl <michl@2n.cz>
- *
- * Hardware definitions for OMAP5910 based VoiceBlue board.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_VOICEBLUE_H
-#define __ASM_ARCH_VOICEBLUE_H
-
-extern void voiceblue_wdt_enable(void);
-extern void voiceblue_wdt_disable(void);
-extern void voiceblue_wdt_ping(void);
-
-#endif /* __ASM_ARCH_VOICEBLUE_H */
-
select PINCTRL
select SOC_BUS
select OMAP_IRQCHIP
+ select CLKSRC_TI_32K
help
Systems based on OMAP2, OMAP3, OMAP4 or OMAP5
# Functions loaded to SRAM
obj-$(CONFIG_SOC_OMAP2420) += sram242x.o
obj-$(CONFIG_SOC_OMAP2430) += sram243x.o
-obj-$(CONFIG_ARCH_OMAP3) += sram34xx.o
AFLAGS_sram242x.o :=-Wa,-march=armv6
AFLAGS_sram243x.o :=-Wa,-march=armv6
-AFLAGS_sram34xx.o :=-Wa,-march=armv7-a
# Restart code (OMAP4/5 currently in omap4-common.c)
obj-$(CONFIG_SOC_OMAP2420) += omap2-restart.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o
obj-$(CONFIG_ARCH_OMAP3) += $(clock-common)
-obj-$(CONFIG_ARCH_OMAP3) += clkt34xx_dpll3m2.o
obj-$(CONFIG_ARCH_OMAP4) += $(clock-common)
obj-$(CONFIG_SOC_AM33XX) += $(clock-common)
obj-$(CONFIG_SOC_OMAP5) += $(clock-common)
.map_io = omap242x_map_io,
.init_early = omap2420_init_early,
.init_machine = omap_generic_init,
- .init_time = omap2_sync32k_timer_init,
+ .init_time = omap_init_time,
.dt_compat = omap242x_boards_compat,
.restart = omap2xxx_restart,
MACHINE_END
.map_io = omap243x_map_io,
.init_early = omap2430_init_early,
.init_machine = omap_generic_init,
- .init_time = omap2_sync32k_timer_init,
+ .init_time = omap_init_time,
.dt_compat = omap243x_boards_compat,
.restart = omap2xxx_restart,
MACHINE_END
.init_early = omap3430_init_early,
.init_machine = omap_generic_init,
.init_late = omap3_init_late,
- .init_time = omap3_sync32k_timer_init,
+ .init_time = omap_init_time,
.dt_compat = n900_boards_compat,
.restart = omap3xxx_restart,
MACHINE_END
.init_early = omap3430_init_early,
.init_machine = omap_generic_init,
.init_late = omap3_init_late,
- .init_time = omap3_sync32k_timer_init,
+ .init_time = omap_init_time,
.dt_compat = omap3_boards_compat,
.restart = omap3xxx_restart,
MACHINE_END
.init_early = omap3630_init_early,
.init_machine = omap_generic_init,
.init_late = omap3_init_late,
- .init_time = omap3_sync32k_timer_init,
+ .init_time = omap_init_time,
.dt_compat = omap36xx_boards_compat,
.restart = omap3xxx_restart,
MACHINE_END
.init_late = am43xx_init_late,
.init_irq = omap_gic_of_init,
.init_machine = omap_generic_init,
- .init_time = omap3_gptimer_timer_init,
+ .init_time = omap4_local_timer_init,
.dt_compat = am43_boards_compat,
.restart = omap44xx_restart,
MACHINE_END
.init_irq = omap3_init_irq,
.init_machine = omap_ldp_init,
.init_late = omap3430_init_late,
- .init_time = omap3_sync32k_timer_init,
+ .init_time = omap_init_time,
.restart = omap3xxx_restart,
MACHINE_END
.init_irq = omap3_init_irq,
.init_machine = rx51_init,
.init_late = omap3430_init_late,
- .init_time = omap3_sync32k_timer_init,
+ .init_time = omap_init_time,
.restart = omap3xxx_restart,
MACHINE_END
+++ /dev/null
-/*
- * OMAP34xx M2 divider clock code
- *
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2010 Nokia Corporation
- *
- * Paul Walmsley
- * Jouni Högander
- *
- * Parts of this code are based on code written by
- * Richard Woodruff, Tony Lindgren, Tuukka Tikkanen, Karthik Dasu
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#undef DEBUG
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-
-#include "clock.h"
-#include "clock3xxx.h"
-#include "sdrc.h"
-#include "sram.h"
-
-#define CYCLES_PER_MHZ 1000000
-
-struct clk *sdrc_ick_p, *arm_fck_p;
-
-/*
- * CORE DPLL (DPLL3) M2 divider rate programming functions
- *
- * These call into SRAM code to do the actual CM writes, since the SDRAM
- * is clocked from DPLL3.
- */
-
-/**
- * omap3_core_dpll_m2_set_rate - set CORE DPLL M2 divider
- * @clk: struct clk * of DPLL to set
- * @rate: rounded target rate
- *
- * Program the DPLL M2 divider with the rounded target rate. Returns
- * -EINVAL upon error, or 0 upon success.
- */
-int omap3_core_dpll_m2_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long parent_rate)
-{
- struct clk_hw_omap *clk = to_clk_hw_omap(hw);
- u32 new_div = 0;
- u32 unlock_dll = 0;
- u32 c;
- unsigned long validrate, sdrcrate, _mpurate;
- struct omap_sdrc_params *sdrc_cs0;
- struct omap_sdrc_params *sdrc_cs1;
- int ret;
- unsigned long clkrate;
-
- if (!clk || !rate)
- return -EINVAL;
-
- new_div = DIV_ROUND_UP(parent_rate, rate);
- validrate = parent_rate / new_div;
-
- if (validrate != rate)
- return -EINVAL;
-
- sdrcrate = clk_get_rate(sdrc_ick_p);
- clkrate = clk_hw_get_rate(hw);
- if (rate > clkrate)
- sdrcrate <<= ((rate / clkrate) >> 1);
- else
- sdrcrate >>= ((clkrate / rate) >> 1);
-
- ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1);
- if (ret)
- return -EINVAL;
-
- if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) {
- pr_debug("clock: will unlock SDRC DLL\n");
- unlock_dll = 1;
- }
-
- /*
- * XXX This only needs to be done when the CPU frequency changes
- */
- _mpurate = clk_get_rate(arm_fck_p) / CYCLES_PER_MHZ;
- c = (_mpurate << SDRC_MPURATE_SCALE) >> SDRC_MPURATE_BASE_SHIFT;
- c += 1; /* for safety */
- c *= SDRC_MPURATE_LOOPS;
- c >>= SDRC_MPURATE_SCALE;
- if (c == 0)
- c = 1;
-
- pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n",
- clkrate, validrate);
- pr_debug("clock: SDRC CS0 timing params used: RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
- sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
- sdrc_cs0->actim_ctrlb, sdrc_cs0->mr);
- if (sdrc_cs1)
- pr_debug("clock: SDRC CS1 timing params used: RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
- sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
- sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
-
- if (sdrc_cs1)
- omap3_configure_core_dpll(
- new_div, unlock_dll, c, rate > clkrate,
- sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
- sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
- sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
- sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
- else
- omap3_configure_core_dpll(
- new_div, unlock_dll, c, rate > clkrate,
- sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
- sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
- 0, 0, 0, 0);
- return 0;
-}
-
extern void omap2_init_common_infrastructure(void);
-extern void omap2_sync32k_timer_init(void);
-extern void omap3_sync32k_timer_init(void);
+extern void omap_init_time(void);
extern void omap3_secure_sync32k_timer_init(void);
extern void omap3_gptimer_timer_init(void);
extern void omap4_local_timer_init(void);
#include "common.h"
#include "mux.h"
#include "control.h"
-#include "devices.h"
#include "display.h"
#define L3_MODULES_MAX_LEN 12
}
omap_postcore_initcall(omap3_l3_init);
-#if defined(CONFIG_IOMMU_API)
-
-#include <linux/platform_data/iommu-omap.h>
-
-static struct resource omap3isp_resources[] = {
- {
- .start = OMAP3430_ISP_BASE,
- .end = OMAP3430_ISP_BASE + 0x12fc,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP3430_ISP_BASE2,
- .end = OMAP3430_ISP_BASE2 + 0x0600,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = 24 + OMAP_INTC_START,
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device omap3isp_device = {
- .name = "omap3isp",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap3isp_resources),
- .resource = omap3isp_resources,
-};
-
-static struct omap_iommu_arch_data omap3_isp_iommu = {
- .name = "mmu_isp",
-};
-
-int omap3_init_camera(struct isp_platform_data *pdata)
-{
- if (of_have_populated_dt())
- omap3_isp_iommu.name = "480bd400.mmu";
-
- omap3isp_device.dev.platform_data = pdata;
- omap3isp_device.dev.archdata.iommu = &omap3_isp_iommu;
-
- return platform_device_register(&omap3isp_device);
-}
-
-#else /* !CONFIG_IOMMU_API */
-
-int omap3_init_camera(struct isp_platform_data *pdata)
-{
- return 0;
-}
-
-#endif
-
#if defined(CONFIG_OMAP2PLUS_MBOX) || defined(CONFIG_OMAP2PLUS_MBOX_MODULE)
static inline void __init omap_init_mbox(void)
{
+++ /dev/null
-/*
- * arch/arm/mach-omap2/devices.h
- *
- * OMAP2 platform device setup/initialization
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef __ARCH_ARM_MACH_OMAP_DEVICES_H
-#define __ARCH_ARM_MACH_OMAP_DEVICES_H
-
-struct isp_platform_data;
-
-int omap3_init_camera(struct isp_platform_data *pdata);
-
-#endif
if (val < OMAP2_DEVICETYPE_MASK)
return val;
- if (cpu_is_omap24xx()) {
+ if (soc_is_omap24xx()) {
val = omap_ctrl_readl(OMAP24XX_CONTROL_STATUS);
- } else if (cpu_is_ti81xx()) {
+ } else if (soc_is_ti81xx()) {
val = omap_ctrl_readl(TI81XX_CONTROL_STATUS);
} else if (soc_is_am33xx() || soc_is_am43xx()) {
val = omap_ctrl_readl(AM33XX_CONTROL_STATUS);
- } else if (cpu_is_omap34xx()) {
+ } else if (soc_is_omap34xx()) {
val = omap_ctrl_readl(OMAP343X_CONTROL_STATUS);
- } else if (cpu_is_omap44xx()) {
+ } else if (soc_is_omap44xx()) {
val = omap_ctrl_readl(OMAP4_CTRL_MODULE_CORE_STATUS);
} else if (soc_is_omap54xx() || soc_is_dra7xx()) {
val = omap_ctrl_readl(OMAP5XXX_CONTROL_STATUS);
void omap_get_die_id(struct omap_die_id *odi)
{
- if (cpu_is_omap44xx() || soc_is_omap54xx() || soc_is_dra7xx()) {
+ if (soc_is_omap44xx() || soc_is_omap54xx() || soc_is_dra7xx()) {
odi->id_0 = read_tap_reg(OMAP_TAP_DIE_ID_44XX_0);
odi->id_1 = read_tap_reg(OMAP_TAP_DIE_ID_44XX_1);
odi->id_2 = read_tap_reg(OMAP_TAP_DIE_ID_44XX_2);
* on available features. Upon detection, update the CPU id
* and CPU class bits.
*/
- if (cpu_is_omap3630()) {
+ if (soc_is_omap3630()) {
cpu_name = "OMAP3630";
} else if (soc_is_am35xx()) {
cpu_name = (omap3_has_sgx()) ? "AM3517" : "AM3505";
- } else if (cpu_is_ti816x()) {
+ } else if (soc_is_ti816x()) {
cpu_name = "TI816X";
} else if (soc_is_am335x()) {
cpu_name = "AM335X";
} else if (soc_is_am437x()) {
cpu_name = "AM437x";
- } else if (cpu_is_ti814x()) {
+ } else if (soc_is_ti814x()) {
cpu_name = "TI814X";
} else if (omap3_has_iva() && omap3_has_sgx()) {
/* OMAP3430, OMAP3525, OMAP3515, OMAP3503 devices */
OMAP3_CHECK_FEATURE(status, SGX);
OMAP3_CHECK_FEATURE(status, NEON);
OMAP3_CHECK_FEATURE(status, ISP);
- if (cpu_is_omap3630())
+ if (soc_is_omap3630())
omap_features |= OMAP3_HAS_192MHZ_CLK;
- if (cpu_is_omap3430() || cpu_is_omap3630())
+ if (soc_is_omap3430() || soc_is_omap3630())
omap_features |= OMAP3_HAS_IO_WAKEUP;
- if (cpu_is_omap3630() || omap_rev() == OMAP3430_REV_ES3_1 ||
+ if (soc_is_omap3630() || omap_rev() == OMAP3430_REV_ES3_1 ||
omap_rev() == OMAP3430_REV_ES3_1_2)
omap_features |= OMAP3_HAS_IO_CHAIN_CTRL;
tap_base = tap;
/* XXX What is this intended to do? */
- if (cpu_is_omap34xx())
+ if (soc_is_omap34xx())
tap_prod_id = 0x0210;
else
tap_prod_id = 0x0208;
static const char * __init omap_get_family(void)
{
- if (cpu_is_omap24xx())
+ if (soc_is_omap24xx())
return kasprintf(GFP_KERNEL, "OMAP2");
- else if (cpu_is_omap34xx())
+ else if (soc_is_omap34xx())
return kasprintf(GFP_KERNEL, "OMAP3");
- else if (cpu_is_omap44xx())
+ else if (soc_is_omap44xx())
return kasprintf(GFP_KERNEL, "OMAP4");
else if (soc_is_omap54xx())
return kasprintf(GFP_KERNEL, "OMAP5");
* platform-specific code to shutdown a CPU
* Called with IRQs disabled
*/
-void __ref omap4_cpu_die(unsigned int cpu)
+void omap4_cpu_die(unsigned int cpu)
{
unsigned int boot_cpu = 0;
void __iomem *base = omap_get_wakeupgen_base();
#include <linux/init.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/irqchip.h>
#include <linux/irqdomain.h>
#include <linux/of_address.h>
#include <linux/platform_device.h>
return NOTIFY_OK;
}
-static struct notifier_block __refdata irq_hotplug_notifier = {
+static struct notifier_block irq_hotplug_notifier = {
.notifier_call = irq_cpu_hotplug_notify,
};
return 0;
}
-
-/*
- * We cannot use the IRQCHIP_DECLARE macro that lives in
- * drivers/irqchip, so we're forced to roll our own. Not very nice.
- */
-OF_DECLARE_2(irqchip, ti_wakeupgen, "ti,omap4-wugen-mpu", wakeupgen_init);
+IRQCHIP_DECLARE(ti_wakeupgen, "ti,omap4-wugen-mpu", wakeupgen_init);
.user = OCP_USER_MPU,
};
-static struct omap_hwmod_addr_space am33xx_elm_addr_space[] = {
- {
- .pa_start = 0x48080000,
- .pa_end = 0x48080000 + SZ_8K - 1,
- .flags = ADDR_TYPE_RT
- },
- { }
-};
-
struct omap_hwmod_ocp_if am33xx_l4_ls__elm = {
.master = &am33xx_l4_ls_hwmod,
.slave = &am33xx_elm_hwmod,
.clk = "l4ls_gclk",
- .addr = am33xx_elm_addr_space,
.user = OCP_USER_MPU,
};
};
/* l3s cfg -> gpmc */
-static struct omap_hwmod_addr_space am33xx_gpmc_addr_space[] = {
- {
- .pa_start = 0x50000000,
- .pa_end = 0x50000000 + SZ_8K - 1,
- .flags = ADDR_TYPE_RT,
- },
- { }
-};
-
struct omap_hwmod_ocp_if am33xx_l3_s__gpmc = {
.master = &am33xx_l3_s_hwmod,
.slave = &am33xx_gpmc_hwmod,
.clk = "l3s_gclk",
- .addr = am33xx_gpmc_addr_space,
.user = OCP_USER_MPU,
};
#include <linux/platform_data/asoc-ti-mcbsp.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <linux/platform_data/iommu-omap.h>
-#include <linux/platform_data/mailbox-omap.h>
#include <plat/dmtimer.h>
#include "soc.h"
.sysc = &omap3xxx_mailbox_sysc,
};
-static struct omap_mbox_dev_info omap3xxx_mailbox_info[] = {
- { .name = "dsp", .tx_id = 0, .rx_id = 1 },
-};
-
-static struct omap_mbox_pdata omap3xxx_mailbox_attrs = {
- .num_users = 2,
- .num_fifos = 2,
- .info_cnt = ARRAY_SIZE(omap3xxx_mailbox_info),
- .info = omap3xxx_mailbox_info,
-};
-
-static struct omap_hwmod_irq_info omap3xxx_mailbox_irqs[] = {
- { .irq = 26 + OMAP_INTC_START, },
- { .irq = -1 },
-};
-
static struct omap_hwmod omap3xxx_mailbox_hwmod = {
.name = "mailbox",
.class = &omap3xxx_mailbox_hwmod_class,
- .mpu_irqs = omap3xxx_mailbox_irqs,
.main_clk = "mailboxes_ick",
.prcm = {
.omap2 = {
.idlest_idle_bit = OMAP3430_ST_MAILBOXES_SHIFT,
},
},
- .dev_attr = &omap3xxx_mailbox_attrs,
};
/*
.user = OCP_USER_MPU,
};
-static struct omap_hwmod_addr_space omap3xxx_mailbox_addrs[] = {
- {
- .pa_start = 0x48094000,
- .pa_end = 0x480941ff,
- .flags = ADDR_TYPE_RT,
- },
- { }
-};
-
/* l4_core -> mailbox */
static struct omap_hwmod_ocp_if omap3xxx_l4_core__mailbox = {
.master = &omap3xxx_l4_core_hwmod,
.slave = &omap3xxx_mailbox_hwmod,
- .addr = omap3xxx_mailbox_addrs,
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-static struct omap_hwmod_addr_space omap44xx_spinlock_addrs[] = {
- {
- .pa_start = 0x4a0f6000,
- .pa_end = 0x4a0f6fff,
- .flags = ADDR_TYPE_RT
- },
- { }
-};
-
/* l4_cfg -> spinlock */
static struct omap_hwmod_ocp_if omap44xx_l4_cfg__spinlock = {
.master = &omap44xx_l4_cfg_hwmod,
.slave = &omap44xx_spinlock_hwmod,
.clk = "l4_div_ck",
- .addr = omap44xx_spinlock_addrs,
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
.rev_offs = 0x0000,
.sysc_offs = 0x0010,
.sysc_flags = (SYSC_HAS_MIDLEMODE | SYSC_HAS_RESET_STATUS |
- SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET |
- SYSC_HAS_RESET_STATUS),
+ SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET),
.idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
SIDLE_SMART_WKUP | MSTANDBY_FORCE | MSTANDBY_NO |
MSTANDBY_SMART | MSTANDBY_SMART_WKUP),
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-static struct omap_hwmod_addr_space dra7xx_elm_addrs[] = {
- {
- .pa_start = 0x48078000,
- .pa_end = 0x48078fff,
- .flags = ADDR_TYPE_RT
- },
- { }
-};
-
/* l4_per1 -> elm */
static struct omap_hwmod_ocp_if dra7xx_l4_per1__elm = {
.master = &dra7xx_l4_per1_hwmod,
.slave = &dra7xx_elm_hwmod,
.clk = "l3_iclk_div",
- .addr = dra7xx_elm_addrs,
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-static struct omap_hwmod_addr_space dra7xx_gpmc_addrs[] = {
- {
- .pa_start = 0x50000000,
- .pa_end = 0x500003ff,
- .flags = ADDR_TYPE_RT
- },
- { }
-};
-
/* l3_main_1 -> gpmc */
static struct omap_hwmod_ocp_if dra7xx_l3_main_1__gpmc = {
.master = &dra7xx_l3_main_1_hwmod,
.slave = &dra7xx_gpmc_hwmod,
.clk = "l3_iclk_div",
- .addr = dra7xx_gpmc_addrs,
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
-static struct omap_hwmod_addr_space dra7xx_spinlock_addrs[] = {
- {
- .pa_start = 0x4a0f6000,
- .pa_end = 0x4a0f6fff,
- .flags = ADDR_TYPE_RT
- },
- { }
-};
-
/* l4_cfg -> spinlock */
static struct omap_hwmod_ocp_if dra7xx_l4_cfg__spinlock = {
.master = &dra7xx_l4_cfg_hwmod,
.slave = &dra7xx_spinlock_hwmod,
.clk = "l3_iclk_div",
- .addr = dra7xx_spinlock_addrs,
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
}
map++;
- };
+ }
return 0;
}
/* Only 81xx needs custom pwrdm_operations */
if (!cpu_is_ti81xx())
- pwrdm_register_platform_funcs(&omap3_pwrdm_operations);;
+ pwrdm_register_platform_funcs(&omap3_pwrdm_operations);
rev = omap_rev();
/*
* omap_rev bits:
- * CPU id bits (0730, 1510, 1710, 2422...) [31:16]
- * CPU revision (See _REV_ defined in cpu.h) [15:08]
- * CPU class bits (15xx, 16xx, 24xx, 34xx...) [07:00]
+ * SoC id bits (0730, 1510, 1710, 2422...) [31:16]
+ * SoC revision (See _REV_ defined in cpu.h) [15:08]
+ * SoC class bits (15xx, 16xx, 24xx, 34xx...) [07:00]
*/
unsigned int omap_rev(void);
}
/*
- * Get the CPU revision for OMAP devices
+ * Get the SoC revision for OMAP devices
*/
#define GET_OMAP_REVISION() ((omap_rev() >> 8) & 0xff)
/*
* Macros to group OMAP into cpu classes.
* These can be used in most places.
- * cpu_is_omap24xx(): True for OMAP2420, OMAP2422, OMAP2423, OMAP2430
- * cpu_is_omap242x(): True for OMAP2420, OMAP2422, OMAP2423
- * cpu_is_omap243x(): True for OMAP2430
- * cpu_is_omap343x(): True for OMAP3430
- * cpu_is_omap443x(): True for OMAP4430
- * cpu_is_omap446x(): True for OMAP4460
- * cpu_is_omap447x(): True for OMAP4470
+ * soc_is_omap24xx(): True for OMAP2420, OMAP2422, OMAP2423, OMAP2430
+ * soc_is_omap242x(): True for OMAP2420, OMAP2422, OMAP2423
+ * soc_is_omap243x(): True for OMAP2430
+ * soc_is_omap343x(): True for OMAP3430
+ * soc_is_omap443x(): True for OMAP4430
+ * soc_is_omap446x(): True for OMAP4460
+ * soc_is_omap447x(): True for OMAP4470
* soc_is_omap543x(): True for OMAP5430, OMAP5432
*/
#define GET_OMAP_CLASS (omap_rev() & 0xff)
IS_AM_SUBCLASS(335x, 0x335)
IS_AM_SUBCLASS(437x, 0x437)
-#define cpu_is_omap24xx() 0
-#define cpu_is_omap242x() 0
-#define cpu_is_omap243x() 0
-#define cpu_is_omap34xx() 0
-#define cpu_is_omap343x() 0
-#define cpu_is_ti81xx() 0
-#define cpu_is_ti816x() 0
-#define cpu_is_ti814x() 0
+#define soc_is_omap24xx() 0
+#define soc_is_omap242x() 0
+#define soc_is_omap243x() 0
+#define soc_is_omap34xx() 0
+#define soc_is_omap343x() 0
+#define soc_is_ti81xx() 0
+#define soc_is_ti816x() 0
+#define soc_is_ti814x() 0
#define soc_is_am35xx() 0
#define soc_is_am33xx() 0
#define soc_is_am335x() 0
#define soc_is_am43xx() 0
#define soc_is_am437x() 0
-#define cpu_is_omap44xx() 0
-#define cpu_is_omap443x() 0
-#define cpu_is_omap446x() 0
-#define cpu_is_omap447x() 0
+#define soc_is_omap44xx() 0
+#define soc_is_omap443x() 0
+#define soc_is_omap446x() 0
+#define soc_is_omap447x() 0
#define soc_is_omap54xx() 0
#define soc_is_omap543x() 0
#define soc_is_dra7xx() 0
#if defined(MULTI_OMAP2)
# if defined(CONFIG_ARCH_OMAP2)
-# undef cpu_is_omap24xx
-# define cpu_is_omap24xx() is_omap24xx()
+# undef soc_is_omap24xx
+# define soc_is_omap24xx() is_omap24xx()
# endif
# if defined (CONFIG_SOC_OMAP2420)
-# undef cpu_is_omap242x
-# define cpu_is_omap242x() is_omap242x()
+# undef soc_is_omap242x
+# define soc_is_omap242x() is_omap242x()
# endif
# if defined (CONFIG_SOC_OMAP2430)
-# undef cpu_is_omap243x
-# define cpu_is_omap243x() is_omap243x()
+# undef soc_is_omap243x
+# define soc_is_omap243x() is_omap243x()
# endif
# if defined(CONFIG_ARCH_OMAP3)
-# undef cpu_is_omap34xx
-# undef cpu_is_omap343x
-# define cpu_is_omap34xx() is_omap34xx()
-# define cpu_is_omap343x() is_omap343x()
+# undef soc_is_omap34xx
+# undef soc_is_omap343x
+# define soc_is_omap34xx() is_omap34xx()
+# define soc_is_omap343x() is_omap343x()
# endif
#else
# if defined(CONFIG_ARCH_OMAP2)
-# undef cpu_is_omap24xx
-# define cpu_is_omap24xx() 1
+# undef soc_is_omap24xx
+# define soc_is_omap24xx() 1
# endif
# if defined(CONFIG_SOC_OMAP2420)
-# undef cpu_is_omap242x
-# define cpu_is_omap242x() 1
+# undef soc_is_omap242x
+# define soc_is_omap242x() 1
# endif
# if defined(CONFIG_SOC_OMAP2430)
-# undef cpu_is_omap243x
-# define cpu_is_omap243x() 1
+# undef soc_is_omap243x
+# define soc_is_omap243x() 1
# endif
# if defined(CONFIG_ARCH_OMAP3)
-# undef cpu_is_omap34xx
-# define cpu_is_omap34xx() 1
+# undef soc_is_omap34xx
+# define soc_is_omap34xx() 1
# endif
# if defined(CONFIG_SOC_OMAP3430)
-# undef cpu_is_omap343x
-# define cpu_is_omap343x() 1
+# undef soc_is_omap343x
+# define soc_is_omap343x() 1
# endif
#endif
/*
* Macros to detect individual cpu types.
* These are only rarely needed.
- * cpu_is_omap2420(): True for OMAP2420
- * cpu_is_omap2422(): True for OMAP2422
- * cpu_is_omap2423(): True for OMAP2423
- * cpu_is_omap2430(): True for OMAP2430
- * cpu_is_omap3430(): True for OMAP3430
+ * soc_is_omap2420(): True for OMAP2420
+ * soc_is_omap2422(): True for OMAP2422
+ * soc_is_omap2423(): True for OMAP2423
+ * soc_is_omap2430(): True for OMAP2430
+ * soc_is_omap3430(): True for OMAP3430
*/
#define GET_OMAP_TYPE ((omap_rev() >> 16) & 0xffff)
IS_OMAP_TYPE(2430, 0x2430)
IS_OMAP_TYPE(3430, 0x3430)
-#define cpu_is_omap2420() 0
-#define cpu_is_omap2422() 0
-#define cpu_is_omap2423() 0
-#define cpu_is_omap2430() 0
-#define cpu_is_omap3430() 0
-#define cpu_is_omap3630() 0
+#define soc_is_omap2420() 0
+#define soc_is_omap2422() 0
+#define soc_is_omap2423() 0
+#define soc_is_omap2430() 0
+#define soc_is_omap3430() 0
+#define soc_is_omap3630() 0
#define soc_is_omap5430() 0
/* These are needed for the common code */
#ifdef CONFIG_ARCH_OMAP2PLUS
-#define cpu_is_omap7xx() 0
-#define cpu_is_omap15xx() 0
-#define cpu_is_omap16xx() 0
-#define cpu_is_omap1510() 0
-#define cpu_is_omap1610() 0
-#define cpu_is_omap1611() 0
-#define cpu_is_omap1621() 0
-#define cpu_is_omap1710() 0
+#define soc_is_omap7xx() 0
+#define soc_is_omap15xx() 0
+#define soc_is_omap16xx() 0
+#define soc_is_omap1510() 0
+#define soc_is_omap1610() 0
+#define soc_is_omap1611() 0
+#define soc_is_omap1621() 0
+#define soc_is_omap1710() 0
#define cpu_class_is_omap1() 0
#define cpu_class_is_omap2() 1
#endif
#if defined(CONFIG_ARCH_OMAP2)
-# undef cpu_is_omap2420
-# undef cpu_is_omap2422
-# undef cpu_is_omap2423
-# undef cpu_is_omap2430
-# define cpu_is_omap2420() is_omap2420()
-# define cpu_is_omap2422() is_omap2422()
-# define cpu_is_omap2423() is_omap2423()
-# define cpu_is_omap2430() is_omap2430()
+# undef soc_is_omap2420
+# undef soc_is_omap2422
+# undef soc_is_omap2423
+# undef soc_is_omap2430
+# define soc_is_omap2420() is_omap2420()
+# define soc_is_omap2422() is_omap2422()
+# define soc_is_omap2423() is_omap2423()
+# define soc_is_omap2430() is_omap2430()
#endif
#if defined(CONFIG_ARCH_OMAP3)
-# undef cpu_is_omap3430
-# undef cpu_is_ti81xx
-# undef cpu_is_ti816x
-# undef cpu_is_ti814x
+# undef soc_is_omap3430
+# undef soc_is_ti81xx
+# undef soc_is_ti816x
+# undef soc_is_ti814x
# undef soc_is_am35xx
-# define cpu_is_omap3430() is_omap3430()
-# undef cpu_is_omap3630
-# define cpu_is_omap3630() is_omap363x()
-# define cpu_is_ti81xx() is_ti81xx()
-# define cpu_is_ti816x() is_ti816x()
-# define cpu_is_ti814x() is_ti814x()
+# define soc_is_omap3430() is_omap3430()
+# undef soc_is_omap3630
+# define soc_is_omap3630() is_omap363x()
+# define soc_is_ti81xx() is_ti81xx()
+# define soc_is_ti816x() is_ti816x()
+# define soc_is_ti814x() is_ti814x()
# define soc_is_am35xx() is_am35xx()
#endif
#endif
# if defined(CONFIG_ARCH_OMAP4)
-# undef cpu_is_omap44xx
-# undef cpu_is_omap443x
-# undef cpu_is_omap446x
-# undef cpu_is_omap447x
-# define cpu_is_omap44xx() is_omap44xx()
-# define cpu_is_omap443x() is_omap443x()
-# define cpu_is_omap446x() is_omap446x()
-# define cpu_is_omap447x() is_omap447x()
+# undef soc_is_omap44xx
+# undef soc_is_omap443x
+# undef soc_is_omap446x
+# undef soc_is_omap447x
+# define soc_is_omap44xx() is_omap44xx()
+# define soc_is_omap443x() is_omap443x()
+# define soc_is_omap446x() is_omap446x()
+# define soc_is_omap447x() is_omap447x()
# endif
# if defined(CONFIG_SOC_OMAP5)
#define omap_late_initcall(fn) omap_initcall(late_initcall, fn)
#define omap_late_initcall_sync(fn) omap_initcall(late_initcall_sync, fn)
-#endif /* __ASSEMBLY__ */
+/* Legacy defines, these can be removed when users are removed */
+#define cpu_is_omap2420() soc_is_omap2420()
+#define cpu_is_omap2422() soc_is_omap2422()
+#define cpu_is_omap242x() soc_is_omap242x()
+#define cpu_is_omap2430() soc_is_omap2430()
+#define cpu_is_omap243x() soc_is_omap243x()
+#define cpu_is_omap24xx() soc_is_omap24xx()
+#define cpu_is_omap3430() soc_is_omap3430()
+#define cpu_is_omap343x() soc_is_omap343x()
+#define cpu_is_omap34xx() soc_is_omap34xx()
+#define cpu_is_omap3630() soc_is_omap3630()
+#define cpu_is_omap443x() soc_is_omap443x()
+#define cpu_is_omap446x() soc_is_omap446x()
+#define cpu_is_omap44xx() soc_is_omap44xx()
+#define cpu_is_ti814x() soc_is_ti814x()
+#define cpu_is_ti816x() soc_is_ti816x()
+#define cpu_is_ti81xx() soc_is_ti81xx()
+#endif /* __ASSEMBLY__ */
#ifdef CONFIG_ARCH_OMAP3
-static u32 (*_omap3_sram_configure_core_dpll)(
- u32 m2, u32 unlock_dll, u32 f, u32 inc,
- u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
- u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
- u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
- u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
-
-u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc,
- u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
- u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
- u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
- u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1)
-{
- BUG_ON(!_omap3_sram_configure_core_dpll);
- return _omap3_sram_configure_core_dpll(
- m2, unlock_dll, f, inc,
- sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0,
- sdrc_actim_ctrl_b_0, sdrc_mr_0,
- sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1,
- sdrc_actim_ctrl_b_1, sdrc_mr_1);
-}
-
void omap3_sram_restore_context(void)
{
omap_sram_reset();
- _omap3_sram_configure_core_dpll =
- omap_sram_push(omap3_sram_configure_core_dpll,
- omap3_sram_configure_core_dpll_sz);
omap_push_sram_idle();
}
u32 mem_type);
extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass);
-extern u32 omap3_configure_core_dpll(
- u32 m2, u32 unlock_dll, u32 f, u32 inc,
- u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
- u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
- u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
- u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
extern void omap3_sram_restore_context(void);
/* Do not use these */
u32 mem_type);
extern unsigned long omap243x_sram_reprogram_sdrc_sz;
-extern u32 omap3_sram_configure_core_dpll(
- u32 m2, u32 unlock_dll, u32 f, u32 inc,
- u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
- u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
- u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
- u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
-extern unsigned long omap3_sram_configure_core_dpll_sz;
-
#ifdef CONFIG_PM
extern void omap_push_sram_idle(void);
#else
+++ /dev/null
-/*
- * linux/arch/arm/mach-omap3/sram.S
- *
- * Omap3 specific functions that need to be run in internal SRAM
- *
- * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc.
- * Copyright (C) 2008 Nokia Corporation
- *
- * Rajendra Nayak <rnayak@ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- * Paul Walmsley
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <linux/linkage.h>
-
-#include <asm/assembler.h>
-
-#include "soc.h"
-#include "iomap.h"
-#include "sdrc.h"
-#include "cm3xxx.h"
-
-/*
- * This file needs be built unconditionally as ARM to interoperate correctly
- * with non-Thumb-2-capable firmware.
- */
- .arm
-
- .text
-
-/* r1 parameters */
-#define SDRC_NO_UNLOCK_DLL 0x0
-#define SDRC_UNLOCK_DLL 0x1
-
-/* SDRC_DLLA_CTRL bit settings */
-#define FIXEDDELAY_SHIFT 24
-#define FIXEDDELAY_MASK (0xff << FIXEDDELAY_SHIFT)
-#define DLLIDLE_MASK 0x4
-
-/*
- * SDRC_DLLA_CTRL default values: TI hardware team indicates that
- * FIXEDDELAY should be initialized to 0xf. This apparently was
- * empirically determined during process testing, so no derivation
- * was provided.
- */
-#define FIXEDDELAY_DEFAULT (0x0f << FIXEDDELAY_SHIFT)
-
-/* SDRC_DLLA_STATUS bit settings */
-#define LOCKSTATUS_MASK 0x4
-
-/* SDRC_POWER bit settings */
-#define SRFRONIDLEREQ_MASK 0x40
-
-/* CM_IDLEST1_CORE bit settings */
-#define ST_SDRC_MASK 0x2
-
-/* CM_ICLKEN1_CORE bit settings */
-#define EN_SDRC_MASK 0x2
-
-/* CM_CLKSEL1_PLL bit settings */
-#define CORE_DPLL_CLKOUT_DIV_SHIFT 0x1b
-
-/*
- * omap3_sram_configure_core_dpll - change DPLL3 M2 divider
- *
- * Params passed in registers:
- * r0 = new M2 divider setting (only 1 and 2 supported right now)
- * r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
- * SDRC rates < 83MHz
- * r2 = number of MPU cycles to wait for SDRC to stabilize after
- * reprogramming the SDRC when switching to a slower MPU speed
- * r3 = increasing SDRC rate? (1 = yes, 0 = no)
- *
- * Params passed via the stack. The needed params will be copied in SRAM
- * before use by the code in SRAM (SDRAM is not accessible during SDRC
- * reconfiguration):
- * new SDRC_RFR_CTRL_0 register contents
- * new SDRC_ACTIM_CTRL_A_0 register contents
- * new SDRC_ACTIM_CTRL_B_0 register contents
- * new SDRC_MR_0 register value
- * new SDRC_RFR_CTRL_1 register contents
- * new SDRC_ACTIM_CTRL_A_1 register contents
- * new SDRC_ACTIM_CTRL_B_1 register contents
- * new SDRC_MR_1 register value
- *
- * If the param SDRC_RFR_CTRL_1 is 0, the parameters are not programmed into
- * the SDRC CS1 registers
- *
- * NOTE: This code no longer attempts to program the SDRC AC timing and MR
- * registers. This is because the code currently cannot ensure that all
- * L3 initiators (e.g., sDMA, IVA, DSS DISPC, etc.) are not accessing the
- * SDRAM when the registers are written. If the registers are changed while
- * an initiator is accessing SDRAM, memory can be corrupted and/or the SDRC
- * may enter an unpredictable state. In the future, the intent is to
- * re-enable this code in cases where we can ensure that no initiators are
- * touching the SDRAM. Until that time, users who know that their use case
- * can satisfy the above requirement can enable the CONFIG_OMAP3_SDRC_AC_TIMING
- * option.
- *
- * Richard Woodruff notes that any changes to this code must be carefully
- * audited and tested to ensure that they don't cause a TLB miss while
- * the SDRAM is inaccessible. Such a situation will crash the system
- * since it will cause the ARM MMU to attempt to walk the page tables.
- * These crashes may be intermittent.
- */
- .align 3
-ENTRY(omap3_sram_configure_core_dpll)
- stmfd sp!, {r1-r12, lr} @ store regs to stack
-
- @ pull the extra args off the stack
- @ and store them in SRAM
-
-/*
- * PC-relative stores are deprecated in ARMv7 and lead to undefined behaviour
- * in Thumb-2: use a r7 as a base instead.
- * Be careful not to clobber r7 when maintaing this file.
- */
- THUMB( adr r7, omap3_sram_configure_core_dpll )
- .macro strtext Rt:req, label:req
- ARM( str \Rt, \label )
- THUMB( str \Rt, [r7, \label - omap3_sram_configure_core_dpll] )
- .endm
-
- ldr r4, [sp, #52]
- strtext r4, omap_sdrc_rfr_ctrl_0_val
- ldr r4, [sp, #56]
- strtext r4, omap_sdrc_actim_ctrl_a_0_val
- ldr r4, [sp, #60]
- strtext r4, omap_sdrc_actim_ctrl_b_0_val
- ldr r4, [sp, #64]
- strtext r4, omap_sdrc_mr_0_val
- ldr r4, [sp, #68]
- strtext r4, omap_sdrc_rfr_ctrl_1_val
- cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0,
- beq skip_cs1_params @ do not use cs1 params
- ldr r4, [sp, #72]
- strtext r4, omap_sdrc_actim_ctrl_a_1_val
- ldr r4, [sp, #76]
- strtext r4, omap_sdrc_actim_ctrl_b_1_val
- ldr r4, [sp, #80]
- strtext r4, omap_sdrc_mr_1_val
-skip_cs1_params:
- mrc p15, 0, r8, c1, c0, 0 @ read ctrl register
- bic r10, r8, #0x800 @ clear Z-bit, disable branch prediction
- mcr p15, 0, r10, c1, c0, 0 @ write ctrl register
- dsb @ flush buffered writes to interconnect
- isb @ prevent speculative exec past here
- cmp r3, #1 @ if increasing SDRC clk rate,
- bleq configure_sdrc @ program the SDRC regs early (for RFR)
- cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state
- bleq unlock_dll
- blne lock_dll
- bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC
- bl configure_core_dpll @ change the DPLL3 M2 divider
- mov r12, r2
- bl wait_clk_stable @ wait for SDRC to stabilize
- bl enable_sdrc @ take SDRC out of idle
- cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change
- bleq wait_dll_unlock
- blne wait_dll_lock
- cmp r3, #1 @ if increasing SDRC clk rate,
- beq return_to_sdram @ return to SDRAM code, otherwise,
- bl configure_sdrc @ reprogram SDRC regs now
-return_to_sdram:
- mcr p15, 0, r8, c1, c0, 0 @ restore ctrl register
- isb @ prevent speculative exec past here
- mov r0, #0 @ return value
- ldmfd sp!, {r1-r12, pc} @ restore regs and return
-unlock_dll:
- ldr r11, omap3_sdrc_dlla_ctrl
- ldr r12, [r11]
- bic r12, r12, #FIXEDDELAY_MASK
- orr r12, r12, #FIXEDDELAY_DEFAULT
- orr r12, r12, #DLLIDLE_MASK
- str r12, [r11] @ (no OCP barrier needed)
- bx lr
-lock_dll:
- ldr r11, omap3_sdrc_dlla_ctrl
- ldr r12, [r11]
- bic r12, r12, #DLLIDLE_MASK
- str r12, [r11] @ (no OCP barrier needed)
- bx lr
-sdram_in_selfrefresh:
- ldr r11, omap3_sdrc_power @ read the SDRC_POWER register
- ldr r12, [r11] @ read the contents of SDRC_POWER
- mov r9, r12 @ keep a copy of SDRC_POWER bits
- orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle
- str r12, [r11] @ write back to SDRC_POWER register
- ldr r12, [r11] @ posted-write barrier for SDRC
-idle_sdrc:
- ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg
- ldr r12, [r11]
- bic r12, r12, #EN_SDRC_MASK @ disable iclk bit for SDRC
- str r12, [r11]
-wait_sdrc_idle:
- ldr r11, omap3_cm_idlest1_core
- ldr r12, [r11]
- and r12, r12, #ST_SDRC_MASK @ check for SDRC idle
- cmp r12, #ST_SDRC_MASK
- bne wait_sdrc_idle
- bx lr
-configure_core_dpll:
- ldr r11, omap3_cm_clksel1_pll
- ldr r12, [r11]
- ldr r10, core_m2_mask_val @ modify m2 for core dpll
- and r12, r12, r10
- orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
- str r12, [r11]
- ldr r12, [r11] @ posted-write barrier for CM
- bx lr
-wait_clk_stable:
- subs r12, r12, #1
- bne wait_clk_stable
- bx lr
-enable_sdrc:
- ldr r11, omap3_cm_iclken1_core
- ldr r12, [r11]
- orr r12, r12, #EN_SDRC_MASK @ enable iclk bit for SDRC
- str r12, [r11]
-wait_sdrc_idle1:
- ldr r11, omap3_cm_idlest1_core
- ldr r12, [r11]
- and r12, r12, #ST_SDRC_MASK
- cmp r12, #0
- bne wait_sdrc_idle1
-restore_sdrc_power_val:
- ldr r11, omap3_sdrc_power
- str r9, [r11] @ restore SDRC_POWER, no barrier needed
- bx lr
-wait_dll_lock:
- ldr r11, omap3_sdrc_dlla_status
- ldr r12, [r11]
- and r12, r12, #LOCKSTATUS_MASK
- cmp r12, #LOCKSTATUS_MASK
- bne wait_dll_lock
- bx lr
-wait_dll_unlock:
- ldr r11, omap3_sdrc_dlla_status
- ldr r12, [r11]
- and r12, r12, #LOCKSTATUS_MASK
- cmp r12, #0x0
- bne wait_dll_unlock
- bx lr
-configure_sdrc:
- ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM
- ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM
- str r12, [r11] @ store
-#ifdef CONFIG_OMAP3_SDRC_AC_TIMING
- ldr r12, omap_sdrc_actim_ctrl_a_0_val
- ldr r11, omap3_sdrc_actim_ctrl_a_0
- str r12, [r11]
- ldr r12, omap_sdrc_actim_ctrl_b_0_val
- ldr r11, omap3_sdrc_actim_ctrl_b_0
- str r12, [r11]
- ldr r12, omap_sdrc_mr_0_val
- ldr r11, omap3_sdrc_mr_0
- str r12, [r11]
-#endif
- ldr r12, omap_sdrc_rfr_ctrl_1_val
- cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0,
- beq skip_cs1_prog @ do not program cs1 params
- ldr r11, omap3_sdrc_rfr_ctrl_1
- str r12, [r11]
-#ifdef CONFIG_OMAP3_SDRC_AC_TIMING
- ldr r12, omap_sdrc_actim_ctrl_a_1_val
- ldr r11, omap3_sdrc_actim_ctrl_a_1
- str r12, [r11]
- ldr r12, omap_sdrc_actim_ctrl_b_1_val
- ldr r11, omap3_sdrc_actim_ctrl_b_1
- str r12, [r11]
- ldr r12, omap_sdrc_mr_1_val
- ldr r11, omap3_sdrc_mr_1
- str r12, [r11]
-#endif
-skip_cs1_prog:
- ldr r12, [r11] @ posted-write barrier for SDRC
- bx lr
-
- .align
-omap3_sdrc_power:
- .word OMAP34XX_SDRC_REGADDR(SDRC_POWER)
-omap3_cm_clksel1_pll:
- .word OMAP34XX_CM_REGADDR(PLL_MOD, CM_CLKSEL1)
-omap3_cm_idlest1_core:
- .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST)
-omap3_cm_iclken1_core:
- .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1)
-
-omap3_sdrc_rfr_ctrl_0:
- .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-omap3_sdrc_rfr_ctrl_1:
- .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1)
-omap3_sdrc_actim_ctrl_a_0:
- .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
-omap3_sdrc_actim_ctrl_a_1:
- .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1)
-omap3_sdrc_actim_ctrl_b_0:
- .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
-omap3_sdrc_actim_ctrl_b_1:
- .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1)
-omap3_sdrc_mr_0:
- .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
-omap3_sdrc_mr_1:
- .word OMAP34XX_SDRC_REGADDR(SDRC_MR_1)
-omap_sdrc_rfr_ctrl_0_val:
- .word 0xDEADBEEF
-omap_sdrc_rfr_ctrl_1_val:
- .word 0xDEADBEEF
-omap_sdrc_actim_ctrl_a_0_val:
- .word 0xDEADBEEF
-omap_sdrc_actim_ctrl_a_1_val:
- .word 0xDEADBEEF
-omap_sdrc_actim_ctrl_b_0_val:
- .word 0xDEADBEEF
-omap_sdrc_actim_ctrl_b_1_val:
- .word 0xDEADBEEF
-omap_sdrc_mr_0_val:
- .word 0xDEADBEEF
-omap_sdrc_mr_1_val:
- .word 0xDEADBEEF
-
-omap3_sdrc_dlla_status:
- .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
-omap3_sdrc_dlla_ctrl:
- .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_CTRL)
-core_m2_mask_val:
- .word 0x07FFFFFF
-ENDPROC(omap3_sram_configure_core_dpll)
-
-ENTRY(omap3_sram_configure_core_dpll_sz)
- .word . - omap3_sram_configure_core_dpll
-
of_get_property(np, "ti,timer-secure", NULL)))
continue;
- of_add_property(np, &device_disabled);
+ if (!of_device_is_compatible(np, "ti,omap-counter32k"))
+ of_add_property(np, &device_disabled);
return np;
}
int ret;
struct device_node *np = NULL;
struct omap_hwmod *oh;
- void __iomem *vbase;
const char *oh_name = "counter_32k";
/*
omap_hwmod_setup_one(oh_name);
- if (np) {
- vbase = of_iomap(np, 0);
- of_node_put(np);
- } else {
- vbase = omap_hwmod_get_mpu_rt_va(oh);
- }
-
- if (!vbase) {
- pr_warn("%s: failed to get counter_32k resource\n", __func__);
- return -ENXIO;
- }
-
ret = omap_hwmod_enable(oh);
if (ret) {
pr_warn("%s: failed to enable counter_32k module (%d)\n",
return ret;
}
- ret = omap_init_clocksource_32k(vbase);
- if (ret) {
- pr_warn("%s: failed to initialize counter_32k as a clocksource (%d)\n",
- __func__, ret);
- omap_hwmod_idle(oh);
- }
+ if (!of_have_populated_dt()) {
+ void __iomem *vbase;
+
+ vbase = omap_hwmod_get_mpu_rt_va(oh);
+ ret = omap_init_clocksource_32k(vbase);
+ if (ret) {
+ pr_warn("%s: failed to initialize counter_32k as a clocksource (%d)\n",
+ __func__, ret);
+ omap_hwmod_idle(oh);
+ }
+ }
return ret;
}
clocksource_gpt.name, clksrc.rate);
}
-#ifdef CONFIG_SOC_HAS_REALTIME_COUNTER
+static void __init __omap_sync32k_timer_init(int clkev_nr, const char *clkev_src,
+ const char *clkev_prop, int clksrc_nr, const char *clksrc_src,
+ const char *clksrc_prop, bool gptimer)
+{
+ omap_clk_init();
+ omap_dmtimer_init();
+ omap2_gp_clockevent_init(clkev_nr, clkev_src, clkev_prop);
+
+ /* Enable the use of clocksource="gp_timer" kernel parameter */
+ if (use_gptimer_clksrc || gptimer)
+ omap2_gptimer_clocksource_init(clksrc_nr, clksrc_src,
+ clksrc_prop);
+ else
+ omap2_sync32k_clocksource_init();
+}
+
+void __init omap_init_time(void)
+{
+ __omap_sync32k_timer_init(1, "timer_32k_ck", "ti,timer-alwon",
+ 2, "timer_sys_ck", NULL, false);
+
+ if (of_have_populated_dt())
+ clocksource_probe();
+}
+
+#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM43XX)
+void __init omap3_secure_sync32k_timer_init(void)
+{
+ __omap_sync32k_timer_init(12, "secure_32k_fck", "ti,timer-secure",
+ 2, "timer_sys_ck", NULL, false);
+}
+#endif /* CONFIG_ARCH_OMAP3 */
+
+#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX)
+void __init omap3_gptimer_timer_init(void)
+{
+ __omap_sync32k_timer_init(2, "timer_sys_ck", NULL,
+ 1, "timer_sys_ck", "ti,timer-alwon", true);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) || \
+ defined(CONFIG_SOC_DRA7XX) || defined(CONFIG_SOC_AM43XX)
+static void __init omap4_sync32k_timer_init(void)
+{
+ __omap_sync32k_timer_init(1, "timer_32k_ck", "ti,timer-alwon",
+ 2, "sys_clkin_ck", NULL, false);
+}
+
+void __init omap4_local_timer_init(void)
+{
+ omap4_sync32k_timer_init();
+ clocksource_probe();
+}
+#endif
+
+#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX)
+
/*
* The realtime counter also called master counter, is a free-running
* counter, which is related to real time. It produces the count used
*/
static void __init realtime_counter_init(void)
{
+#ifdef CONFIG_SOC_HAS_REALTIME_COUNTER
void __iomem *base;
static struct clk *sys_clk;
unsigned long rate;
set_cntfreq();
iounmap(base);
-}
-#else
-static inline void __init realtime_counter_init(void)
-{}
#endif
-
-#define OMAP_SYS_GP_TIMER_INIT(name, clkev_nr, clkev_src, clkev_prop, \
- clksrc_nr, clksrc_src, clksrc_prop) \
-void __init omap##name##_gptimer_timer_init(void) \
-{ \
- omap_clk_init(); \
- omap_dmtimer_init(); \
- omap2_gp_clockevent_init((clkev_nr), clkev_src, clkev_prop); \
- omap2_gptimer_clocksource_init((clksrc_nr), clksrc_src, \
- clksrc_prop); \
}
-#define OMAP_SYS_32K_TIMER_INIT(name, clkev_nr, clkev_src, clkev_prop, \
- clksrc_nr, clksrc_src, clksrc_prop) \
-void __init omap##name##_sync32k_timer_init(void) \
-{ \
- omap_clk_init(); \
- omap_dmtimer_init(); \
- omap2_gp_clockevent_init((clkev_nr), clkev_src, clkev_prop); \
- /* Enable the use of clocksource="gp_timer" kernel parameter */ \
- if (use_gptimer_clksrc) \
- omap2_gptimer_clocksource_init((clksrc_nr), clksrc_src, \
- clksrc_prop); \
- else \
- omap2_sync32k_clocksource_init(); \
-}
-
-#ifdef CONFIG_ARCH_OMAP2
-OMAP_SYS_32K_TIMER_INIT(2, 1, "timer_32k_ck", "ti,timer-alwon",
- 2, "timer_sys_ck", NULL);
-#endif /* CONFIG_ARCH_OMAP2 */
-
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM43XX)
-OMAP_SYS_32K_TIMER_INIT(3, 1, "timer_32k_ck", "ti,timer-alwon",
- 2, "timer_sys_ck", NULL);
-OMAP_SYS_32K_TIMER_INIT(3_secure, 12, "secure_32k_fck", "ti,timer-secure",
- 2, "timer_sys_ck", NULL);
-#endif /* CONFIG_ARCH_OMAP3 */
-
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX) || \
- defined(CONFIG_SOC_AM43XX)
-OMAP_SYS_GP_TIMER_INIT(3, 2, "timer_sys_ck", NULL,
- 1, "timer_sys_ck", "ti,timer-alwon");
-#endif
-
-#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) || \
- defined(CONFIG_SOC_DRA7XX)
-static OMAP_SYS_32K_TIMER_INIT(4, 1, "timer_32k_ck", "ti,timer-alwon",
- 2, "sys_clkin_ck", NULL);
-#endif
-
-#ifdef CONFIG_ARCH_OMAP4
-#ifdef CONFIG_HAVE_ARM_TWD
-void __init omap4_local_timer_init(void)
-{
- omap4_sync32k_timer_init();
- clocksource_probe();
-}
-#else
-void __init omap4_local_timer_init(void)
-{
- omap4_sync32k_timer_init();
-}
-#endif /* CONFIG_HAVE_ARM_TWD */
-#endif /* CONFIG_ARCH_OMAP4 */
-
-#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX)
void __init omap5_realtime_timer_init(void)
{
omap4_sync32k_timer_init();
}
}
-#define PRM_POLCTRL_TWL_MASK (OMAP3430_PRM_POLCTRL_CLKREQ_POL | \
- OMAP3430_PRM_POLCTRL_CLKREQ_POL)
-#define PRM_POLCTRL_TWL_VAL OMAP3430_PRM_POLCTRL_CLKREQ_POL
-
/*
* Configure signal polarity for sys_clkreq and sys_off_mode pins
* as the default values are wrong and can cause the system to hang
*
* Called with IRQs disabled
*/
-void __ref sirfsoc_cpu_die(unsigned int cpu)
+void sirfsoc_cpu_die(unsigned int cpu)
{
platform_do_lowpower(cpu);
}
#include <linux/dm9000.h>
#include <linux/leds.h>
#include <linux/rtc-v3020.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/i2c.h>
#endif
#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
+static struct pwm_lookup cm_x300_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 1, "pwm-backlight.0", NULL, 10000,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data cm_x300_backlight_data = {
- .pwm_id = 2,
.max_brightness = 100,
.dft_brightness = 100,
- .pwm_period_ns = 10000,
.enable_gpio = -1,
};
static void cm_x300_init_bl(void)
{
+ pwm_add_table(cm_x300_pwm_lookup, ARRAY_SIZE(cm_x300_pwm_lookup));
platform_device_register(&cm_x300_backlight_device);
}
#else
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/i2c/pxa-i2c.h>
* Backlight
******************************************************************************/
#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
+static struct pwm_lookup income_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.0", NULL, 1000000,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data income_backlight_data = {
- .pwm_id = 0,
.max_brightness = 0x3ff,
.dft_brightness = 0x1ff,
- .pwm_period_ns = 1000000,
.enable_gpio = -1,
};
static void __init income_pwm_init(void)
{
+ pwm_add_table(income_pwm_lookup, ARRAY_SIZE(income_pwm_lookup));
platform_device_register(&income_backlight);
}
#else
.end = IRQ_ICP,
.flags = IORESOURCE_IRQ,
},
+ [3] = {
+ .start = 0x40800000,
+ .end = 0x4080001b,
+ .flags = IORESOURCE_MEM,
+ },
+ [4] = {
+ .start = 0x40700000,
+ .end = 0x40700023,
+ .flags = IORESOURCE_MEM,
+ },
+ [5] = {
+ .start = 17,
+ .end = 17,
+ .flags = IORESOURCE_DMA,
+ },
+ [6] = {
+ .start = 18,
+ .end = 18,
+ .flags = IORESOURCE_DMA,
+ },
};
struct platform_device pxa_device_ficp = {
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/input.h>
#include <linux/gpio.h>
#define GPIO19_GEN1_CAM_RST 19
#define GPIO28_GEN2_CAM_RST 28
+static struct pwm_lookup ezx_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.0", NULL, 78700,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data ezx_backlight_data = {
- .pwm_id = 0,
.max_brightness = 1023,
.dft_brightness = 1023,
- .pwm_period_ns = 78770,
.enable_gpio = -1,
};
platform_device_register(&a780_camera);
}
+ pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(a780_devices));
}
*/
static struct platform_pwm_backlight_data backlight_data = {
- .pwm_id = -1, /* Superseded by pwm_lookup */
.max_brightness = 200,
.dft_brightness = 100,
- .pwm_period_ns = 30923,
.enable_gpio = -1,
};
static struct pxa2xx_spi_master pxa_ssp2_master_info = {
.num_chipselect = 1,
- .clock_enable = CKEN_SSP2,
.enable_dma = 1,
};
};
static struct pxa2xx_spi_master pxa_ssp3_spi_master_info = {
- .clock_enable = CKEN_SSP3,
.num_chipselect = 2,
.enable_dma = 1
};
static struct pxa2xx_spi_master pxa_ssp4_spi_master_info = {
- .clock_enable = CKEN_SSP4,
.num_chipselect = 2,
.enable_dma = 1
};
#define GPIO101_MAGICIAN_KEY_VOL_DOWN 101
#define GPIO102_MAGICIAN_KEY_PHONE 102
#define GPIO103_MAGICIAN_LED_KP 103
-#define GPIO104_MAGICIAN_LCD_POWER_1 104
-#define GPIO105_MAGICIAN_LCD_POWER_2 105
-#define GPIO106_MAGICIAN_LCD_POWER_3 106
+#define GPIO104_MAGICIAN_LCD_VOFF_EN 104
+#define GPIO105_MAGICIAN_LCD_VON_EN 105
+#define GPIO106_MAGICIAN_LCD_DCDC_NRESET 106
#define GPIO107_MAGICIAN_DS1WM_IRQ 107
#define GPIO108_MAGICIAN_GSM_READY 108
#define GPIO114_MAGICIAN_UNKNOWN 114
* CPLD EGPIOs
*/
-#define MAGICIAN_EGPIO_BASE PXA_NR_BUILTIN_GPIO
+#define MAGICIAN_EGPIO_BASE PXA_NR_BUILTIN_GPIO
#define MAGICIAN_EGPIO(reg,bit) \
(MAGICIAN_EGPIO_BASE + 8*reg + bit)
/* output */
-#define EGPIO_MAGICIAN_TOPPOLY_POWER MAGICIAN_EGPIO(0, 2)
-#define EGPIO_MAGICIAN_LED_POWER MAGICIAN_EGPIO(0, 5)
-#define EGPIO_MAGICIAN_GSM_RESET MAGICIAN_EGPIO(0, 6)
-#define EGPIO_MAGICIAN_LCD_POWER MAGICIAN_EGPIO(0, 7)
-#define EGPIO_MAGICIAN_SPK_POWER MAGICIAN_EGPIO(1, 0)
-#define EGPIO_MAGICIAN_EP_POWER MAGICIAN_EGPIO(1, 1)
-#define EGPIO_MAGICIAN_IN_SEL0 MAGICIAN_EGPIO(1, 2)
-#define EGPIO_MAGICIAN_IN_SEL1 MAGICIAN_EGPIO(1, 3)
-#define EGPIO_MAGICIAN_MIC_POWER MAGICIAN_EGPIO(1, 4)
-#define EGPIO_MAGICIAN_CODEC_RESET MAGICIAN_EGPIO(1, 5)
-#define EGPIO_MAGICIAN_CODEC_POWER MAGICIAN_EGPIO(1, 6)
-#define EGPIO_MAGICIAN_BL_POWER MAGICIAN_EGPIO(1, 7)
-#define EGPIO_MAGICIAN_SD_POWER MAGICIAN_EGPIO(2, 0)
-#define EGPIO_MAGICIAN_CARKIT_MIC MAGICIAN_EGPIO(2, 1)
-#define EGPIO_MAGICIAN_UNKNOWN_WAVEDEV_DLL MAGICIAN_EGPIO(2, 2)
-#define EGPIO_MAGICIAN_FLASH_VPP MAGICIAN_EGPIO(2, 3)
-#define EGPIO_MAGICIAN_BL_POWER2 MAGICIAN_EGPIO(2, 4)
-#define EGPIO_MAGICIAN_BQ24022_ISET2 MAGICIAN_EGPIO(2, 5)
-#define EGPIO_MAGICIAN_GSM_POWER MAGICIAN_EGPIO(2, 7)
+#define EGPIO_MAGICIAN_TOPPOLY_POWER MAGICIAN_EGPIO(0, 2)
+#define EGPIO_MAGICIAN_LED_POWER MAGICIAN_EGPIO(0, 5)
+#define EGPIO_MAGICIAN_GSM_RESET MAGICIAN_EGPIO(0, 6)
+#define EGPIO_MAGICIAN_LCD_POWER MAGICIAN_EGPIO(0, 7)
+#define EGPIO_MAGICIAN_SPK_POWER MAGICIAN_EGPIO(1, 0)
+#define EGPIO_MAGICIAN_EP_POWER MAGICIAN_EGPIO(1, 1)
+#define EGPIO_MAGICIAN_IN_SEL0 MAGICIAN_EGPIO(1, 2)
+#define EGPIO_MAGICIAN_IN_SEL1 MAGICIAN_EGPIO(1, 3)
+#define EGPIO_MAGICIAN_MIC_POWER MAGICIAN_EGPIO(1, 4)
+#define EGPIO_MAGICIAN_CODEC_RESET MAGICIAN_EGPIO(1, 5)
+#define EGPIO_MAGICIAN_CODEC_POWER MAGICIAN_EGPIO(1, 6)
+#define EGPIO_MAGICIAN_BL_POWER MAGICIAN_EGPIO(1, 7)
+#define EGPIO_MAGICIAN_SD_POWER MAGICIAN_EGPIO(2, 0)
+#define EGPIO_MAGICIAN_CARKIT_MIC MAGICIAN_EGPIO(2, 1)
+#define EGPIO_MAGICIAN_IR_RX_SHUTDOWN MAGICIAN_EGPIO(2, 2)
+#define EGPIO_MAGICIAN_FLASH_VPP MAGICIAN_EGPIO(2, 3)
+#define EGPIO_MAGICIAN_BL_POWER2 MAGICIAN_EGPIO(2, 4)
+#define EGPIO_MAGICIAN_BQ24022_ISET2 MAGICIAN_EGPIO(2, 5)
+#define EGPIO_MAGICIAN_NICD_CHARGE MAGICIAN_EGPIO(2, 6)
+#define EGPIO_MAGICIAN_GSM_POWER MAGICIAN_EGPIO(2, 7)
/* input */
-#define EGPIO_MAGICIAN_CABLE_STATE_AC MAGICIAN_EGPIO(4, 0)
-#define EGPIO_MAGICIAN_CABLE_STATE_USB MAGICIAN_EGPIO(4, 1)
+/* USB or AC charger type */
+#define EGPIO_MAGICIAN_CABLE_TYPE MAGICIAN_EGPIO(4, 0)
+/*
+ * Vbus is detected
+ * FIXME behaves like (6,3), may differ for host/device
+ */
+#define EGPIO_MAGICIAN_CABLE_VBUS MAGICIAN_EGPIO(4, 1)
-#define EGPIO_MAGICIAN_BOARD_ID0 MAGICIAN_EGPIO(5, 0)
-#define EGPIO_MAGICIAN_BOARD_ID1 MAGICIAN_EGPIO(5, 1)
-#define EGPIO_MAGICIAN_BOARD_ID2 MAGICIAN_EGPIO(5, 2)
-#define EGPIO_MAGICIAN_LCD_SELECT MAGICIAN_EGPIO(5, 3)
-#define EGPIO_MAGICIAN_nSD_READONLY MAGICIAN_EGPIO(5, 4)
+#define EGPIO_MAGICIAN_BOARD_ID0 MAGICIAN_EGPIO(5, 0)
+#define EGPIO_MAGICIAN_BOARD_ID1 MAGICIAN_EGPIO(5, 1)
+#define EGPIO_MAGICIAN_BOARD_ID2 MAGICIAN_EGPIO(5, 2)
+#define EGPIO_MAGICIAN_LCD_SELECT MAGICIAN_EGPIO(5, 3)
+#define EGPIO_MAGICIAN_nSD_READONLY MAGICIAN_EGPIO(5, 4)
-#define EGPIO_MAGICIAN_EP_INSERT MAGICIAN_EGPIO(6, 1)
+#define EGPIO_MAGICIAN_EP_INSERT MAGICIAN_EGPIO(6, 1)
+/* FIXME behaves like (4,1), may differ for host/device */
+#define EGPIO_MAGICIAN_CABLE_INSERTED MAGICIAN_EGPIO(6, 3)
#endif /* _MAGICIAN_H_ */
#define ARB_CORE_PARK (1<<24) /* Be parked with core when idle */
#define ARB_LOCK_FLAG (1<<23) /* Only Locking masters gain access to the bus */
-extern int __init pxa27x_set_pwrmode(unsigned int mode);
+extern int pxa27x_set_pwrmode(unsigned int mode);
extern void pxa27x_cpu_pm_enter(suspend_state_t state);
#endif /* __MACH_PXA27x_H */
#include <linux/ioport.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/smc91x.h>
},
};
+static struct pwm_lookup lpd270_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.0", NULL, 78770,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data lpd270_backlight_data = {
- .pwm_id = 0,
.max_brightness = 1,
.dft_brightness = 1,
- .pwm_period_ns = 78770,
.enable_gpio = -1,
};
*/
ARB_CNTRL = ARB_CORE_PARK | 0x234;
+ pwm_add_table(lpd270_pwm_lookup, ARRAY_SIZE(lpd270_pwm_lookup));
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
pxa_set_ac97_info(NULL);
#include <linux/mfd/htc-pasic3.h>
#include <linux/mtd/physmap.h>
#include <linux/pda_power.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/regulator/driver.h>
+#include <linux/regulator/fixed.h>
#include <linux/regulator/gpio-regulator.h>
#include <linux/regulator/machine.h>
#include <linux/usb/gpio_vbus.h>
#include <linux/platform_data/irda-pxaficp.h>
#include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/regulator/max1586.h>
+
+#include <linux/platform_data/pxa2xx_udc.h>
+#include <mach/udc.h>
+#include <mach/pxa27x-udc.h>
+
#include "devices.h"
#include "generic.h"
GPIO20_nSDCS_2,
GPIO21_nSDCS_3,
GPIO15_nCS_1,
- GPIO78_nCS_2, /* PASIC3 */
- GPIO79_nCS_3, /* EGPIO CPLD */
+ GPIO78_nCS_2, /* PASIC3 */
+ GPIO79_nCS_3, /* EGPIO CPLD */
GPIO80_nCS_4,
GPIO33_nCS_5,
- /* I2C */
+ /* I2C UDA1380 + OV9640 */
GPIO117_I2C_SCL,
GPIO118_I2C_SDA,
- /* PWM 0 */
+ /* PWM 0 - LCD backlight */
GPIO16_PWM0_OUT,
- /* I2S */
+ /* I2S UDA1380 capture */
GPIO28_I2S_BITCLK_OUT,
GPIO29_I2S_SDATA_IN,
GPIO31_I2S_SYNC,
GPIO113_I2S_SYSCLK,
- /* SSP 1 */
+ /* SSP 1 UDA1380 playback */
GPIO23_SSP1_SCLK,
GPIO24_SSP1_SFRM,
GPIO25_SSP1_TXD,
- /* SSP 2 */
+ /* SSP 2 TSC2046 touchscreen */
GPIO19_SSP2_SCLK,
GPIO14_SSP2_SFRM,
GPIO89_SSP2_TXD,
GPIO88_SSP2_RXD,
- /* MMC */
+ /* MMC/SD/SDHC slot */
GPIO32_MMC_CLK,
GPIO92_MMC_DAT_0,
GPIO109_MMC_DAT_1,
/* LCD */
GPIOxx_LCD_TFT_16BPP,
- /* QCI */
+ /* QCI camera interface */
GPIO12_CIF_DD_7,
GPIO17_CIF_DD_6,
GPIO50_CIF_DD_3,
};
/*
- * IRDA
+ * IrDA
*/
static struct pxaficp_platform_data magician_ficp_info = {
.gpio_pwdown = GPIO83_MAGICIAN_nIR_EN,
.transceiver_cap = IR_SIRMODE | IR_OFF,
+ .gpio_pwdown_inverted = 0,
};
/*
#define INIT_KEY(_code, _gpio, _desc) \
{ \
- .code = KEY_##_code, \
- .gpio = _gpio, \
- .desc = _desc, \
- .type = EV_KEY, \
- .wakeup = 1, \
+ .code = KEY_##_code, \
+ .gpio = _gpio, \
+ .desc = _desc, \
+ .type = EV_KEY, \
+ .wakeup = 1, \
}
static struct gpio_keys_button magician_button_table[] = {
};
static struct gpio_keys_platform_data gpio_keys_data = {
- .buttons = magician_button_table,
- .nbuttons = ARRAY_SIZE(magician_button_table),
+ .buttons = magician_button_table,
+ .nbuttons = ARRAY_SIZE(magician_button_table),
};
static struct platform_device gpio_keys = {
- .name = "gpio-keys",
- .dev = {
+ .name = "gpio-keys",
+ .dev = {
.platform_data = &gpio_keys_data,
},
- .id = -1,
+ .id = -1,
};
-
/*
* EGPIO (Xilinx CPLD)
*
- * 7 32-bit aligned 8-bit registers: 3x output, 1x irq, 3x input
+ * 32-bit aligned 8-bit registers
+ * 16 possible registers (reg windows size), only 7 used:
+ * 3x output, 1x irq, 3x input
*/
static struct resource egpio_resources[] = {
[0] = {
- .start = PXA_CS3_PHYS,
- .end = PXA_CS3_PHYS + 0x20 - 1,
- .flags = IORESOURCE_MEM,
+ .start = PXA_CS3_PHYS,
+ .end = PXA_CS3_PHYS + 0x20 - 1,
+ .flags = IORESOURCE_MEM,
},
[1] = {
- .start = PXA_GPIO_TO_IRQ(GPIO13_MAGICIAN_CPLD_IRQ),
- .end = PXA_GPIO_TO_IRQ(GPIO13_MAGICIAN_CPLD_IRQ),
- .flags = IORESOURCE_IRQ,
+ .start = PXA_GPIO_TO_IRQ(GPIO13_MAGICIAN_CPLD_IRQ),
+ .end = PXA_GPIO_TO_IRQ(GPIO13_MAGICIAN_CPLD_IRQ),
+ .flags = IORESOURCE_IRQ,
},
};
static struct htc_egpio_chip egpio_chips[] = {
[0] = {
- .reg_start = 0,
- .gpio_base = MAGICIAN_EGPIO(0, 0),
- .num_gpios = 24,
- .direction = HTC_EGPIO_OUTPUT,
- .initial_values = 0x40, /* EGPIO_MAGICIAN_GSM_RESET */
+ .reg_start = 0,
+ .gpio_base = MAGICIAN_EGPIO(0, 0),
+ .num_gpios = 24,
+ .direction = HTC_EGPIO_OUTPUT,
+ /*
+ * Depends on modules configuration
+ */
+ .initial_values = 0x40, /* EGPIO_MAGICIAN_GSM_RESET */
},
[1] = {
- .reg_start = 4,
- .gpio_base = MAGICIAN_EGPIO(4, 0),
- .num_gpios = 24,
- .direction = HTC_EGPIO_INPUT,
+ .reg_start = 4,
+ .gpio_base = MAGICIAN_EGPIO(4, 0),
+ .num_gpios = 24,
+ .direction = HTC_EGPIO_INPUT,
},
};
static struct htc_egpio_platform_data egpio_info = {
- .reg_width = 8,
- .bus_width = 32,
- .irq_base = IRQ_BOARD_START,
- .num_irqs = 4,
- .ack_register = 3,
- .chip = egpio_chips,
- .num_chips = ARRAY_SIZE(egpio_chips),
+ .reg_width = 8,
+ .bus_width = 32,
+ .irq_base = IRQ_BOARD_START,
+ .num_irqs = 4,
+ .ack_register = 3,
+ .chip = egpio_chips,
+ .num_chips = ARRAY_SIZE(egpio_chips),
};
static struct platform_device egpio = {
- .name = "htc-egpio",
- .id = -1,
- .resource = egpio_resources,
- .num_resources = ARRAY_SIZE(egpio_resources),
+ .name = "htc-egpio",
+ .id = -1,
+ .resource = egpio_resources,
+ .num_resources = ARRAY_SIZE(egpio_resources),
.dev = {
.platform_data = &egpio_info,
},
};
/*
- * LCD - Toppoly TD028STEB1 or Samsung LTP280QV
+ * PXAFB LCD - Toppoly TD028STEB1 or Samsung LTP280QV
*/
static struct pxafb_mode_info toppoly_modes[] = {
{
- .pixclock = 96153,
- .bpp = 16,
- .xres = 240,
- .yres = 320,
- .hsync_len = 11,
- .vsync_len = 3,
- .left_margin = 19,
- .upper_margin = 2,
- .right_margin = 10,
- .lower_margin = 2,
- .sync = 0,
+ .pixclock = 96153,
+ .bpp = 16,
+ .xres = 240,
+ .yres = 320,
+ .hsync_len = 11,
+ .vsync_len = 3,
+ .left_margin = 19,
+ .upper_margin = 2,
+ .right_margin = 10,
+ .lower_margin = 2,
+ .sync = 0,
},
};
static struct pxafb_mode_info samsung_modes[] = {
{
- .pixclock = 96153,
- .bpp = 16,
- .xres = 240,
- .yres = 320,
- .hsync_len = 8,
- .vsync_len = 4,
- .left_margin = 9,
- .upper_margin = 4,
- .right_margin = 9,
- .lower_margin = 4,
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .pixclock = 226469,
+ .bpp = 16,
+ .xres = 240,
+ .yres = 320,
+ .hsync_len = 8,
+ .vsync_len = 4,
+ .left_margin = 9,
+ .upper_margin = 4,
+ .right_margin = 9,
+ .lower_margin = 4,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
},
};
static void toppoly_lcd_power(int on, struct fb_var_screeninfo *si)
{
- pr_debug("Toppoly LCD power\n");
+ pr_debug("Toppoly LCD power: %s\n", on ? "on" : "off");
if (on) {
- pr_debug("on\n");
gpio_set_value(EGPIO_MAGICIAN_TOPPOLY_POWER, 1);
- gpio_set_value(GPIO106_MAGICIAN_LCD_POWER_3, 1);
+ gpio_set_value(GPIO106_MAGICIAN_LCD_DCDC_NRESET, 1);
udelay(2000);
gpio_set_value(EGPIO_MAGICIAN_LCD_POWER, 1);
udelay(2000);
/* FIXME: enable LCDC here */
udelay(2000);
- gpio_set_value(GPIO104_MAGICIAN_LCD_POWER_1, 1);
+ gpio_set_value(GPIO104_MAGICIAN_LCD_VOFF_EN, 1);
udelay(2000);
- gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 1);
+ gpio_set_value(GPIO105_MAGICIAN_LCD_VON_EN, 1);
} else {
- pr_debug("off\n");
msleep(15);
- gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 0);
+ gpio_set_value(GPIO105_MAGICIAN_LCD_VON_EN, 0);
udelay(500);
- gpio_set_value(GPIO104_MAGICIAN_LCD_POWER_1, 0);
+ gpio_set_value(GPIO104_MAGICIAN_LCD_VOFF_EN, 0);
udelay(1000);
- gpio_set_value(GPIO106_MAGICIAN_LCD_POWER_3, 0);
+ gpio_set_value(GPIO106_MAGICIAN_LCD_DCDC_NRESET, 0);
gpio_set_value(EGPIO_MAGICIAN_LCD_POWER, 0);
}
}
static void samsung_lcd_power(int on, struct fb_var_screeninfo *si)
{
- pr_debug("Samsung LCD power\n");
+ pr_debug("Samsung LCD power: %s\n", on ? "on" : "off");
if (on) {
- pr_debug("on\n");
if (system_rev < 3)
gpio_set_value(GPIO75_MAGICIAN_SAMSUNG_POWER, 1);
else
gpio_set_value(EGPIO_MAGICIAN_LCD_POWER, 1);
- mdelay(10);
- gpio_set_value(GPIO106_MAGICIAN_LCD_POWER_3, 1);
- mdelay(10);
- gpio_set_value(GPIO104_MAGICIAN_LCD_POWER_1, 1);
- mdelay(30);
- gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 1);
- mdelay(10);
+ mdelay(6);
+ gpio_set_value(GPIO106_MAGICIAN_LCD_DCDC_NRESET, 1);
+ mdelay(6); /* Avdd -> Voff >5ms */
+ gpio_set_value(GPIO104_MAGICIAN_LCD_VOFF_EN, 1);
+ mdelay(16); /* Voff -> Von >(5+10)ms */
+ gpio_set_value(GPIO105_MAGICIAN_LCD_VON_EN, 1);
} else {
- pr_debug("off\n");
- mdelay(10);
- gpio_set_value(GPIO105_MAGICIAN_LCD_POWER_2, 0);
- mdelay(30);
- gpio_set_value(GPIO104_MAGICIAN_LCD_POWER_1, 0);
- mdelay(10);
- gpio_set_value(GPIO106_MAGICIAN_LCD_POWER_3, 0);
- mdelay(10);
+ gpio_set_value(GPIO105_MAGICIAN_LCD_VON_EN, 0);
+ mdelay(16);
+ gpio_set_value(GPIO104_MAGICIAN_LCD_VOFF_EN, 0);
+ mdelay(6);
+ gpio_set_value(GPIO106_MAGICIAN_LCD_DCDC_NRESET, 0);
+ mdelay(6);
if (system_rev < 3)
gpio_set_value(GPIO75_MAGICIAN_SAMSUNG_POWER, 0);
else
}
static struct pxafb_mach_info toppoly_info = {
- .modes = toppoly_modes,
- .num_modes = 1,
- .fixed_modes = 1,
- .lcd_conn = LCD_COLOR_TFT_16BPP,
- .pxafb_lcd_power = toppoly_lcd_power,
+ .modes = toppoly_modes,
+ .num_modes = 1,
+ .fixed_modes = 1,
+ .lcd_conn = LCD_COLOR_TFT_16BPP,
+ .pxafb_lcd_power = toppoly_lcd_power,
};
static struct pxafb_mach_info samsung_info = {
- .modes = samsung_modes,
- .num_modes = 1,
- .fixed_modes = 1,
- .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL |\
- LCD_ALTERNATE_MAPPING,
- .pxafb_lcd_power = samsung_lcd_power,
+ .modes = samsung_modes,
+ .num_modes = 1,
+ .fixed_modes = 1,
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL |
+ LCD_ALTERNATE_MAPPING,
+ .pxafb_lcd_power = samsung_lcd_power,
};
/*
* Backlight
*/
+static struct pwm_lookup magician_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight", NULL, 30923,
+ PWM_POLARITY_NORMAL),
+};
+
+ /*
+ * fixed regulator for pwm_backlight
+ */
+
+static struct regulator_consumer_supply pwm_backlight_supply[] = {
+ REGULATOR_SUPPLY("power", "pwm_backlight"),
+};
+
+
static struct gpio magician_bl_gpios[] = {
- { EGPIO_MAGICIAN_BL_POWER, GPIOF_DIR_OUT, "Backlight power" },
- { EGPIO_MAGICIAN_BL_POWER2, GPIOF_DIR_OUT, "Backlight power 2" },
+ { EGPIO_MAGICIAN_BL_POWER, GPIOF_DIR_OUT, "Backlight power" },
+ { EGPIO_MAGICIAN_BL_POWER2, GPIOF_DIR_OUT, "Backlight power 2" },
};
static int magician_backlight_init(struct device *dev)
static int magician_backlight_notify(struct device *dev, int brightness)
{
+ pr_debug("Brightness = %i\n", brightness);
gpio_set_value(EGPIO_MAGICIAN_BL_POWER, brightness);
if (brightness >= 200) {
gpio_set_value(EGPIO_MAGICIAN_BL_POWER2, 1);
gpio_free_array(ARRAY_AND_SIZE(magician_bl_gpios));
}
+/*
+ * LCD PWM backlight (main)
+ *
+ * MP1521 frequency should be:
+ * 100-400 Hz = 2 .5*10^6 - 10 *10^6 ns
+ */
+
static struct platform_pwm_backlight_data backlight_data = {
- .pwm_id = 0,
- .max_brightness = 272,
- .dft_brightness = 100,
- .pwm_period_ns = 30923,
- .enable_gpio = -1,
- .init = magician_backlight_init,
- .notify = magician_backlight_notify,
- .exit = magician_backlight_exit,
+ .max_brightness = 272,
+ .dft_brightness = 100,
+ .enable_gpio = -1,
+ .init = magician_backlight_init,
+ .notify = magician_backlight_notify,
+ .exit = magician_backlight_exit,
};
static struct platform_device backlight = {
- .name = "pwm-backlight",
- .id = -1,
- .dev = {
- .parent = &pxa27x_device_pwm0.dev,
- .platform_data = &backlight_data,
+ .name = "pwm-backlight",
+ .id = -1,
+ .dev = {
+ .parent = &pxa27x_device_pwm0.dev,
+ .platform_data = &backlight_data,
},
};
/*
- * LEDs
+ * GPIO LEDs, Phone keys backlight, vibra
*/
static struct gpio_led gpio_leds[] = {
};
static struct platform_device leds_gpio = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
.platform_data = &gpio_led_info,
},
};
-static struct pasic3_led pasic3_leds[] = {
- {
- .led = {
- .name = "magician:red",
- .default_trigger = "ds2760-battery.0-charging",
- },
- .hw_num = 0,
- .bit2 = PASIC3_BIT2_LED0,
- .mask = PASIC3_MASK_LED0,
- },
- {
- .led = {
- .name = "magician:green",
- .default_trigger = "ds2760-battery.0-charging-or-full",
- },
- .hw_num = 1,
- .bit2 = PASIC3_BIT2_LED1,
- .mask = PASIC3_MASK_LED1,
- },
- {
- .led = {
- .name = "magician:blue",
- .default_trigger = "bluetooth",
- },
- .hw_num = 2,
- .bit2 = PASIC3_BIT2_LED2,
- .mask = PASIC3_MASK_LED2,
- },
-};
-
-static struct pasic3_leds_machinfo pasic3_leds_info = {
- .num_leds = ARRAY_SIZE(pasic3_leds),
- .power_gpio = EGPIO_MAGICIAN_LED_POWER,
- .leds = pasic3_leds,
-};
-
/*
* PASIC3 with DS1WM
*/
static struct resource pasic3_resources[] = {
[0] = {
- .start = PXA_CS2_PHYS,
+ .start = PXA_CS2_PHYS,
.end = PXA_CS2_PHYS + 0x1b,
- .flags = IORESOURCE_MEM,
+ .flags = IORESOURCE_MEM,
},
/* No IRQ handler in the PASIC3, DS1WM needs an external IRQ */
[1] = {
- .start = PXA_GPIO_TO_IRQ(GPIO107_MAGICIAN_DS1WM_IRQ),
- .end = PXA_GPIO_TO_IRQ(GPIO107_MAGICIAN_DS1WM_IRQ),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+ .start = PXA_GPIO_TO_IRQ(GPIO107_MAGICIAN_DS1WM_IRQ),
+ .end = PXA_GPIO_TO_IRQ(GPIO107_MAGICIAN_DS1WM_IRQ),
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
}
};
static struct pasic3_platform_data pasic3_platform_data = {
- .led_pdata = &pasic3_leds_info,
.clock_rate = 4000000,
};
};
/*
- * USB "Transceiver"
+ * PXA UDC
+ */
+
+static void magician_udc_command(int cmd)
+{
+ if (cmd == PXA2XX_UDC_CMD_CONNECT)
+ UP2OCR |= UP2OCR_DPPUE | UP2OCR_DPPUBE;
+ else if (cmd == PXA2XX_UDC_CMD_DISCONNECT)
+ UP2OCR &= ~(UP2OCR_DPPUE | UP2OCR_DPPUBE);
+}
+
+static struct pxa2xx_udc_mach_info magician_udc_info __initdata = {
+ .udc_command = magician_udc_command,
+ .gpio_pullup = GPIO27_MAGICIAN_USBC_PUEN,
+};
+
+/*
+ * USB device VBus detection
*/
static struct resource gpio_vbus_resource = {
- .flags = IORESOURCE_IRQ,
- .start = IRQ_MAGICIAN_VBUS,
- .end = IRQ_MAGICIAN_VBUS,
+ .flags = IORESOURCE_IRQ,
+ .start = IRQ_MAGICIAN_VBUS,
+ .end = IRQ_MAGICIAN_VBUS,
};
static struct gpio_vbus_mach_info gpio_vbus_info = {
- .gpio_pullup = GPIO27_MAGICIAN_USBC_PUEN,
- .gpio_vbus = EGPIO_MAGICIAN_CABLE_STATE_USB,
+ .gpio_pullup = GPIO27_MAGICIAN_USBC_PUEN,
+ .gpio_vbus = EGPIO_MAGICIAN_CABLE_VBUS,
};
static struct platform_device gpio_vbus = {
- .name = "gpio-vbus",
- .id = -1,
- .num_resources = 1,
- .resource = &gpio_vbus_resource,
+ .name = "gpio-vbus",
+ .id = -1,
+ .num_resources = 1,
+ .resource = &gpio_vbus_resource,
.dev = {
.platform_data = &gpio_vbus_info,
},
* External power
*/
-static int power_supply_init(struct device *dev)
+static int magician_supply_init(struct device *dev)
+{
+ int ret = -1;
+
+ ret = gpio_request(EGPIO_MAGICIAN_CABLE_TYPE, "Cable is AC charger");
+ if (ret) {
+ pr_err("Cannot request AC/USB charger GPIO (%i)\n", ret);
+ goto err_ac;
+ }
+
+ ret = gpio_request(EGPIO_MAGICIAN_CABLE_INSERTED, "Cable inserted");
+ if (ret) {
+ pr_err("Cannot request cable detection GPIO (%i)\n", ret);
+ goto err_usb;
+ }
+
+ return 0;
+
+err_usb:
+ gpio_free(EGPIO_MAGICIAN_CABLE_TYPE);
+err_ac:
+ return ret;
+}
+
+static void magician_set_charge(int flags)
{
- return gpio_request(EGPIO_MAGICIAN_CABLE_STATE_AC, "CABLE_STATE_AC");
+ if (flags & PDA_POWER_CHARGE_AC) {
+ pr_debug("Charging from AC\n");
+ gpio_set_value(EGPIO_MAGICIAN_NICD_CHARGE, 1);
+ } else if (flags & PDA_POWER_CHARGE_USB) {
+ pr_debug("Charging from USB\n");
+ gpio_set_value(EGPIO_MAGICIAN_NICD_CHARGE, 1);
+ } else {
+ pr_debug("Charging disabled\n");
+ gpio_set_value(EGPIO_MAGICIAN_NICD_CHARGE, 0);
+ }
}
static int magician_is_ac_online(void)
{
- return gpio_get_value(EGPIO_MAGICIAN_CABLE_STATE_AC);
+ return gpio_get_value(EGPIO_MAGICIAN_CABLE_INSERTED) &&
+ gpio_get_value(EGPIO_MAGICIAN_CABLE_TYPE); /* AC=1 */
}
-static void power_supply_exit(struct device *dev)
+static int magician_is_usb_online(void)
{
- gpio_free(EGPIO_MAGICIAN_CABLE_STATE_AC);
+ return gpio_get_value(EGPIO_MAGICIAN_CABLE_INSERTED) &&
+ (!gpio_get_value(EGPIO_MAGICIAN_CABLE_TYPE)); /* USB=0 */
+}
+
+static void magician_supply_exit(struct device *dev)
+{
+ gpio_free(EGPIO_MAGICIAN_CABLE_INSERTED);
+ gpio_free(EGPIO_MAGICIAN_CABLE_TYPE);
}
static char *magician_supplicants[] = {
};
static struct pda_power_pdata power_supply_info = {
- .init = power_supply_init,
- .is_ac_online = magician_is_ac_online,
- .exit = power_supply_exit,
- .supplied_to = magician_supplicants,
- .num_supplicants = ARRAY_SIZE(magician_supplicants),
+ .init = magician_supply_init,
+ .exit = magician_supply_exit,
+ .is_ac_online = magician_is_ac_online,
+ .is_usb_online = magician_is_usb_online,
+ .set_charge = magician_set_charge,
+ .supplied_to = magician_supplicants,
+ .num_supplicants = ARRAY_SIZE(magician_supplicants),
};
static struct resource power_supply_resources[] = {
[0] = {
- .name = "ac",
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
- IORESOURCE_IRQ_LOWEDGE,
- .start = IRQ_MAGICIAN_VBUS,
- .end = IRQ_MAGICIAN_VBUS,
+ .name = "ac",
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
+ IORESOURCE_IRQ_LOWEDGE,
+ .start = IRQ_MAGICIAN_VBUS,
+ .end = IRQ_MAGICIAN_VBUS,
},
[1] = {
- .name = "usb",
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
- IORESOURCE_IRQ_LOWEDGE,
- .start = IRQ_MAGICIAN_VBUS,
- .end = IRQ_MAGICIAN_VBUS,
+ .name = "usb",
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
+ IORESOURCE_IRQ_LOWEDGE,
+ .start = IRQ_MAGICIAN_VBUS,
+ .end = IRQ_MAGICIAN_VBUS,
},
};
static struct platform_device power_supply = {
- .name = "pda-power",
- .id = -1,
- .dev = {
+ .name = "pda-power",
+ .id = -1,
+ .dev = {
.platform_data = &power_supply_info,
},
- .resource = power_supply_resources,
- .num_resources = ARRAY_SIZE(power_supply_resources),
+ .resource = power_supply_resources,
+ .num_resources = ARRAY_SIZE(power_supply_resources),
};
/*
static struct regulator_init_data bq24022_init_data = {
.constraints = {
- .max_uA = 500000,
- .valid_ops_mask = REGULATOR_CHANGE_CURRENT | REGULATOR_CHANGE_STATUS,
+ .max_uA = 500000,
+ .valid_ops_mask = REGULATOR_CHANGE_CURRENT |
+ REGULATOR_CHANGE_STATUS,
},
- .num_consumer_supplies = ARRAY_SIZE(bq24022_consumers),
- .consumer_supplies = bq24022_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(bq24022_consumers),
+ .consumer_supplies = bq24022_consumers,
};
static struct gpio bq24022_gpios[] = {
};
static struct gpio_regulator_config bq24022_info = {
- .supply_name = "bq24022",
+ .supply_name = "bq24022",
- .enable_gpio = GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
- .enable_high = 0,
- .enabled_at_boot = 0,
+ .enable_gpio = GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
+ .enable_high = 0,
+ .enabled_at_boot = 1,
- .gpios = bq24022_gpios,
- .nr_gpios = ARRAY_SIZE(bq24022_gpios),
+ .gpios = bq24022_gpios,
+ .nr_gpios = ARRAY_SIZE(bq24022_gpios),
- .states = bq24022_states,
- .nr_states = ARRAY_SIZE(bq24022_states),
+ .states = bq24022_states,
+ .nr_states = ARRAY_SIZE(bq24022_states),
- .type = REGULATOR_CURRENT,
- .init_data = &bq24022_init_data,
+ .type = REGULATOR_CURRENT,
+ .init_data = &bq24022_init_data,
};
static struct platform_device bq24022 = {
- .name = "gpio-regulator",
- .id = -1,
- .dev = {
+ .name = "gpio-regulator",
+ .id = -1,
+ .dev = {
.platform_data = &bq24022_info,
},
};
+/*
+ * Vcore regulator MAX1587A
+ */
+
+static struct regulator_consumer_supply magician_max1587a_consumers[] = {
+ REGULATOR_SUPPLY("vcc_core", NULL),
+};
+
+static struct regulator_init_data magician_max1587a_v3_info = {
+ .constraints = {
+ .name = "vcc_core range",
+ .min_uV = 700000,
+ .max_uV = 1475000,
+ .always_on = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ },
+ .consumer_supplies = magician_max1587a_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(magician_max1587a_consumers),
+};
+
+static struct max1586_subdev_data magician_max1587a_subdevs[] = {
+ {
+ .name = "vcc_core",
+ .id = MAX1586_V3,
+ .platform_data = &magician_max1587a_v3_info,
+ }
+};
+
+static struct max1586_platform_data magician_max1587a_info = {
+ .subdevs = magician_max1587a_subdevs,
+ .num_subdevs = ARRAY_SIZE(magician_max1587a_subdevs),
+ /*
+ * NOTICE measured directly on the PCB (board_id == 0x3a), but
+ * if R24 is present, it will boost the voltage
+ * (write 1.475V, get 1.645V and smoke)
+ */
+ .v3_gain = MAX1586_GAIN_NO_R24,
+};
+
+static struct i2c_board_info magician_pwr_i2c_board_info[] __initdata = {
+ {
+ I2C_BOARD_INFO("max1586", 0x14),
+ .platform_data = &magician_max1587a_info,
+ },
+};
+
/*
* MMC/SD
*/
static int magician_mci_init(struct device *dev,
- irq_handler_t detect_irq, void *data)
+ irq_handler_t detect_irq, void *data)
{
return request_irq(IRQ_MAGICIAN_SD, detect_irq, 0,
- "mmc card detect", data);
+ "mmc card detect", data);
}
static void magician_mci_exit(struct device *dev, void *data)
}
static struct pxamci_platform_data magician_mci_info = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = magician_mci_init,
- .exit = magician_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = magician_mci_init,
+ .exit = magician_mci_exit,
.gpio_card_detect = -1,
.gpio_card_ro = EGPIO_MAGICIAN_nSD_READONLY,
.gpio_card_ro_invert = 1,
static struct pxaohci_platform_data magician_ohci_info = {
.port_mode = PMM_PERPORT_MODE,
- .flags = ENABLE_PORT1 | ENABLE_PORT3 | POWER_CONTROL_LOW,
+ /* port1: CSR Bluetooth, port2: OTG with UDC */
+ .flags = ENABLE_PORT1 | ENABLE_PORT2 | POWER_CONTROL_LOW,
.power_budget = 0,
+ .power_on_delay = 100,
};
-
/*
* StrataFlash
*/
+static int magician_flash_init(struct platform_device *pdev)
+{
+ int ret = gpio_request(EGPIO_MAGICIAN_FLASH_VPP, "flash Vpp enable");
+
+ if (ret) {
+ pr_err("Cannot request flash enable GPIO (%i)\n", ret);
+ return ret;
+ }
+
+ ret = gpio_direction_output(EGPIO_MAGICIAN_FLASH_VPP, 1);
+ if (ret) {
+ pr_err("Cannot set direction for flash enable (%i)\n", ret);
+ gpio_free(EGPIO_MAGICIAN_FLASH_VPP);
+ }
+
+ return ret;
+}
+
static void magician_set_vpp(struct platform_device *pdev, int vpp)
{
gpio_set_value(EGPIO_MAGICIAN_FLASH_VPP, vpp);
}
+static void magician_flash_exit(struct platform_device *pdev)
+{
+ gpio_free(EGPIO_MAGICIAN_FLASH_VPP);
+}
+
static struct resource strataflash_resource = {
- .start = PXA_CS0_PHYS,
- .end = PXA_CS0_PHYS + SZ_64M - 1,
- .flags = IORESOURCE_MEM,
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_64M - 1,
+ .flags = IORESOURCE_MEM,
};
+static struct mtd_partition magician_flash_parts[] = {
+ {
+ .name = "Bootloader",
+ .offset = 0x0,
+ .size = 0x40000,
+ .mask_flags = MTD_WRITEABLE, /* EXPERIMENTAL */
+ },
+ {
+ .name = "Linux Kernel",
+ .offset = 0x40000,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+/*
+ * physmap-flash driver
+ */
+
static struct physmap_flash_data strataflash_data = {
- .width = 4,
- .set_vpp = magician_set_vpp,
+ .width = 4,
+ .init = magician_flash_init,
+ .set_vpp = magician_set_vpp,
+ .exit = magician_flash_exit,
+ .parts = magician_flash_parts,
+ .nr_parts = ARRAY_SIZE(magician_flash_parts),
};
static struct platform_device strataflash = {
- .name = "physmap-flash",
- .id = -1,
- .resource = &strataflash_resource,
- .num_resources = 1,
+ .name = "physmap-flash",
+ .id = -1,
+ .resource = &strataflash_resource,
+ .num_resources = 1,
.dev = {
.platform_data = &strataflash_data,
},
};
/*
- * I2C
+ * PXA I2C main controller
*/
static struct i2c_pxa_platform_data i2c_info = {
- .fast_mode = 1,
+ /* OV9640 I2C device doesn't support fast mode */
+ .fast_mode = 0,
+};
+
+/*
+ * PXA I2C power controller
+ */
+
+static struct i2c_pxa_platform_data magician_i2c_power_info = {
+ .fast_mode = 1,
};
/*
};
static struct gpio magician_global_gpios[] = {
- { GPIO13_MAGICIAN_CPLD_IRQ, GPIOF_IN, "CPLD_IRQ" },
+ { GPIO13_MAGICIAN_CPLD_IRQ, GPIOF_IN, "CPLD_IRQ" },
{ GPIO107_MAGICIAN_DS1WM_IRQ, GPIOF_IN, "DS1WM_IRQ" },
- { GPIO104_MAGICIAN_LCD_POWER_1, GPIOF_OUT_INIT_LOW, "LCD power 1" },
- { GPIO105_MAGICIAN_LCD_POWER_2, GPIOF_OUT_INIT_LOW, "LCD power 2" },
- { GPIO106_MAGICIAN_LCD_POWER_3, GPIOF_OUT_INIT_LOW, "LCD power 3" },
- { GPIO83_MAGICIAN_nIR_EN, GPIOF_OUT_INIT_HIGH, "nIR_EN" },
+
+ /* NOTICE valid LCD init sequence */
+ { GPIO106_MAGICIAN_LCD_DCDC_NRESET, GPIOF_OUT_INIT_LOW, "LCD DCDC nreset" },
+ { GPIO104_MAGICIAN_LCD_VOFF_EN, GPIOF_OUT_INIT_LOW, "LCD VOFF enable" },
+ { GPIO105_MAGICIAN_LCD_VON_EN, GPIOF_OUT_INIT_LOW, "LCD VON enable" },
};
static void __init magician_init(void)
pxa2xx_mfp_config(ARRAY_AND_SIZE(magician_pin_config));
err = gpio_request_array(ARRAY_AND_SIZE(magician_global_gpios));
if (err)
- pr_err("magician: Failed to request GPIOs: %d\n", err);
+ pr_err("magician: Failed to request global GPIOs: %d\n", err);
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
- pxa_set_stuart_info(NULL);
- platform_add_devices(ARRAY_AND_SIZE(devices));
+ pwm_add_table(magician_pwm_lookup, ARRAY_SIZE(magician_pwm_lookup));
pxa_set_ficp_info(&magician_ficp_info);
- pxa27x_set_i2c_power_info(NULL);
+ pxa27x_set_i2c_power_info(&magician_i2c_power_info);
pxa_set_i2c_info(&i2c_info);
+
+ i2c_register_board_info(1,
+ ARRAY_AND_SIZE(magician_pwr_i2c_board_info));
+
pxa_set_mci_info(&magician_mci_info);
pxa_set_ohci_info(&magician_ohci_info);
+ pxa_set_udc_info(&magician_udc_info);
/* Check LCD type we have */
cpld = ioremap_nocache(PXA_CS3_PHYS, 0x1000);
if (cpld) {
- u8 board_id = __raw_readb(cpld+0x14);
+ u8 board_id = __raw_readb(cpld + 0x14);
+
iounmap(cpld);
system_rev = board_id & 0x7;
lcd_select = board_id & 0x8;
pr_info("LCD type: %s\n", lcd_select ? "Samsung" : "Toppoly");
if (lcd_select && (system_rev < 3))
+ /* NOTICE valid LCD init sequence */
gpio_request_one(GPIO75_MAGICIAN_SAMSUNG_POWER,
- GPIOF_OUT_INIT_LOW, "SAMSUNG_POWER");
- pxa_set_fb_info(NULL, lcd_select ? &samsung_info : &toppoly_info);
+ GPIOF_OUT_INIT_LOW, "Samsung LCD Power");
+ pxa_set_fb_info(NULL,
+ lcd_select ? &samsung_info : &toppoly_info);
} else
pr_err("LCD detection: CPLD mapping failed\n");
-}
+ regulator_register_always_on(0, "power", pwm_backlight_supply,
+ ARRAY_SIZE(pwm_backlight_supply), 5000000);
+
+ platform_add_devices(ARRAY_AND_SIZE(devices));
+}
MACHINE_START(MAGICIAN, "HTC Magician")
- .atag_offset = 0x100,
- .map_io = pxa27x_map_io,
- .nr_irqs = MAGICIAN_NR_IRQS,
- .init_irq = pxa27x_init_irq,
- .handle_irq = pxa27x_handle_irq,
- .init_machine = magician_init,
+ .atag_offset = 0x100,
+ .map_io = pxa27x_map_io,
+ .nr_irqs = MAGICIAN_NR_IRQS,
+ .init_irq = pxa27x_init_irq,
+ .handle_irq = pxa27x_handle_irq,
+ .init_machine = magician_init,
.init_time = pxa_timer_init,
.restart = pxa_restart,
MACHINE_END
#include <linux/mtd/partitions.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/smc91x.h>
#include <linux/i2c/pxa-i2c.h>
};
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
+static struct pwm_lookup mainstone_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.0", NULL, 78770,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data mainstone_backlight_data = {
- .pwm_id = 0,
.max_brightness = 1023,
.dft_brightness = 1023,
- .pwm_period_ns = 78770,
.enable_gpio = -1,
};
static void __init mainstone_backlight_register(void)
{
- int ret = platform_device_register(&mainstone_backlight_device);
- if (ret)
+ int ret;
+
+ pwm_add_table(mainstone_pwm_lookup, ARRAY_SIZE(mainstone_pwm_lookup));
+
+ ret = platform_device_register(&mainstone_backlight_device);
+ if (ret) {
printk(KERN_ERR "mainstone: failed to register backlight device: %d\n", ret);
+ pwm_remove_table(mainstone_pwm_lookup,
+ ARRAY_SIZE(mainstone_pwm_lookup));
+ }
}
#else
#define mainstone_backlight_register() do { } while (0)
#include <linux/input.h>
#include <linux/delay.h>
#include <linux/gpio_keys.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/rtc.h>
#include <linux/leds.h>
MFP_CFG_OUT(GPIO116, AF0, DRIVE_HIGH),
};
+static struct pwm_lookup mioa701_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight", NULL, 4000 * 1024,
+ PWM_POLARITY_NORMAL),
+};
+
/* LCD Screen and Backlight */
static struct platform_pwm_backlight_data mioa701_backlight_data = {
- .pwm_id = 0,
.max_brightness = 100,
.dft_brightness = 50,
- .pwm_period_ns = 4000 * 1024, /* Fl = 250kHz */
.enable_gpio = -1,
};
MIO_SIMPLE_DEV(pxa2xx_pcm, "pxa2xx-pcm", NULL)
MIO_SIMPLE_DEV(mioa701_sound, "mioa701-wm9713", NULL)
MIO_SIMPLE_DEV(mioa701_board, "mioa701-board", NULL)
+MIO_SIMPLE_DEV(wm9713_acodec, "wm9713-codec", NULL);
MIO_SIMPLE_DEV(gpio_vbus, "gpio-vbus", &gpio_vbus_data);
MIO_SIMPLE_DEV(mioa701_camera, "soc-camera-pdrv",&iclink);
&mioa701_gpio_keys,
&mioa701_backlight,
&mioa701_led,
+ &wm9713_acodec,
&pxa2xx_pcm,
&mioa701_sound,
&power_dev,
pxa_set_udc_info(&mioa701_udc_info);
pxa_set_ac97_info(&mioa701_ac97_info);
pm_power_off = mioa701_poweroff;
+ pwm_add_table(mioa701_pwm_lookup, ARRAY_SIZE(mioa701_pwm_lookup));
platform_add_devices(devices, ARRAY_SIZE(devices));
gsm_init();
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/pda_power.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/gpio.h>
#include <linux/wm97xx.h>
* Backlight
******************************************************************************/
#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
+static struct pwm_lookup palm27x_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.0", NULL, 3500 * 1024,
+ PWM_POLARITY_NORMAL),
+};
+
static int palm_bl_power;
static int palm_lcd_power;
}
static struct platform_pwm_backlight_data palm27x_backlight_data = {
- .pwm_id = 0,
.max_brightness = 0xfe,
.dft_brightness = 0x7e,
- .pwm_period_ns = 3500 * 1024,
.enable_gpio = -1,
.init = palm27x_backlight_init,
.notify = palm27x_backlight_notify,
{
palm_bl_power = bl;
palm_lcd_power = lcd;
+ pwm_add_lookup(palm27x_pwm_lookup, ARRAY_SIZE(palm27x_pwm_lookup));
platform_device_register(&palm27x_backlight);
}
#endif
#include <linux/delay.h>
#include <linux/irq.h>
#include <linux/input.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/gpio.h>
#include <linux/input/matrix_keypad.h>
* Backlight
******************************************************************************/
#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
+static struct pwm_lookup palmtc_pwm_lookup[] = {
+ PWM_LOOKUP("pxa25x-pwm.1", 0, "pwm-backlight.0", NULL, PALMTC_PERIOD_NS,
+ PWM_PERIOD_NORMAL),
+};
+
static struct platform_pwm_backlight_data palmtc_backlight_data = {
- .pwm_id = 1,
.max_brightness = PALMTC_MAX_INTENSITY,
.dft_brightness = PALMTC_MAX_INTENSITY,
- .pwm_period_ns = PALMTC_PERIOD_NS,
.enable_gpio = GPIO_NR_PALMTC_BL_POWER,
};
static void __init palmtc_pwm_init(void)
{
+ pwm_add_table(palmtc_pwm_lookup, ARRAY_SIZE(palmtc_pwm_lookup));
platform_device_register(&palmtc_backlight);
}
#else
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/pda_power.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/gpio.h>
#include <linux/wm97xx.h>
/******************************************************************************
* Backlight
******************************************************************************/
+static struct pwm_lookup palmte2_pwm_lookup[] = {
+ PWM_LOOKUP("pxa25x-pwm.0", 0, "pwm-backlight.0", NULL,
+ PALMTE2_PERIOD_NS, PWM_POLARITY_NORMAL),
+};
+
static struct gpio palmte_bl_gpios[] = {
{ GPIO_NR_PALMTE2_BL_POWER, GPIOF_INIT_LOW, "Backlight power" },
{ GPIO_NR_PALMTE2_LCD_POWER, GPIOF_INIT_LOW, "LCD power" },
}
static struct platform_pwm_backlight_data palmte2_backlight_data = {
- .pwm_id = 0,
.max_brightness = PALMTE2_MAX_INTENSITY,
.dft_brightness = PALMTE2_MAX_INTENSITY,
- .pwm_period_ns = PALMTE2_PERIOD_NS,
.enable_gpio = -1,
.init = palmte2_backlight_init,
.notify = palmte2_backlight_notify,
pxa_set_ac97_info(&palmte2_ac97_pdata);
pxa_set_ficp_info(&palmte2_ficp_platform_data);
+ pwm_add_table(palmte2_pwm_lookup, ARRAY_SIZE(palmte2_pwm_lookup));
platform_add_devices(devices, ARRAY_SIZE(devices));
}
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/i2c/pxa-i2c.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <media/mt9v022.h>
};
#endif
+static struct pwm_lookup pcm990_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.0", NULL, 78770,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data pcm990_backlight_data = {
- .pwm_id = 0,
.max_brightness = 1023,
.dft_brightness = 1023,
- .pwm_period_ns = 78770,
.enable_gpio = -1,
};
#ifndef CONFIG_PCM990_DISPLAY_NONE
pxa_set_fb_info(NULL, &pcm990_fbinfo);
#endif
+ pwm_add_table(pcm990_pwm_lookup, ARRAY_SIZE(pcm990_pwm_lookup));
platform_device_register(&pcm990_backlight_device);
/* MMC */
*/
static unsigned int pwrmode = PWRMODE_SLEEP;
-int __init pxa27x_set_pwrmode(unsigned int mode)
+int pxa27x_set_pwrmode(unsigned int mode)
{
switch (mode) {
case PWRMODE_SLEEP:
#include <linux/leds.h>
#include <linux/w1-gpio.h>
#include <linux/sched.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/i2c.h>
#include <linux/i2c/pxa-i2c.h>
.ext_pullup_enable_pin = -EINVAL,
};
-struct platform_device raumfeld_w1_gpio_device = {
+static struct platform_device raumfeld_w1_gpio_device = {
.name = "w1-gpio",
.dev = {
.platform_data = &w1_gpio_platform_data
* Framebuffer device
*/
+static struct pwm_lookup raumfeld_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight", NULL, 10000,
+ PWM_POLARITY_NORMAL),
+};
+
/* PWM controlled backlight */
static struct platform_pwm_backlight_data raumfeld_pwm_backlight_data = {
- .pwm_id = 0,
.max_brightness = 100,
.dft_brightness = 100,
- /* 10000 ns = 10 ms ^= 100 kHz */
- .pwm_period_ns = 10000,
.enable_gpio = -1,
};
} else {
mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT;
pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1);
+ pwm_add_table(raumfeld_pwm_lookup,
+ ARRAY_SIZE(raumfeld_pwm_lookup));
platform_device_register(&raumfeld_pwm_backlight_device);
}
* SPI devices
*/
-struct spi_gpio_platform_data raumfeld_spi_platform_data = {
+static struct spi_gpio_platform_data raumfeld_spi_platform_data = {
.sck = GPIO_SPI_CLK,
.mosi = GPIO_SPI_MOSI,
.miso = GPIO_SPI_MISO,
static struct regulator_consumer_supply audio_va_consumer_supply =
REGULATOR_SUPPLY("va", "0-0048");
-struct regulator_init_data audio_va_initdata = {
+static struct regulator_init_data audio_va_initdata = {
.consumer_supplies = &audio_va_consumer_supply,
.num_consumer_supplies = 1,
.constraints = {
REGULATOR_SUPPLY("vlc", "0-0048"),
};
-struct regulator_init_data audio_dummy_initdata = {
+static struct regulator_init_data audio_dummy_initdata = {
.consumer_supplies = audio_dummy_supplies,
.num_consumer_supplies = ARRAY_SIZE(audio_dummy_supplies),
.constraints = {
.num_consumer_supplies = 1,
};
-struct max8660_subdev_data max8660_v6_subdev_data = {
+static struct max8660_subdev_data max8660_v6_subdev_data = {
.id = MAX8660_V6,
.name = "vmmc",
.platform_data = &vcc_mmc_init_data,
#include <linux/clk.h>
#include <linux/gpio.h>
#include <linux/smc91x.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <asm/mach-types.h>
#endif /* CONFIG_KEYBOARD_PXA27x || CONFIG_KEYBOARD_PXA27x_MODULE */
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
+static struct pwm_lookup tavorevb_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.0", 1, "pwm-backlight.0", NULL, 100000,
+ PWM_POLARITY_NORMAL),
+ PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight.1", NULL, 100000,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data tavorevb_backlight_data[] = {
[0] = {
/* primary backlight */
- .pwm_id = 2,
.max_brightness = 100,
.dft_brightness = 100,
- .pwm_period_ns = 100000,
.enable_gpio = -1,
},
[1] = {
/* secondary backlight */
- .pwm_id = 0,
.max_brightness = 100,
.dft_brightness = 100,
- .pwm_period_ns = 100000,
.enable_gpio = -1,
},
};
static void __init tavorevb_init_lcd(void)
{
+ pwm_add_table(tavorevb_pwm_lookup, ARRAY_SIZE(tavorevb_pwm_lookup));
platform_device_register(&tavorevb_backlight_devices[0]);
platform_device_register(&tavorevb_backlight_devices[1]);
pxa_set_fb_info(NULL, &tavorevb_lcd_info);
#include <linux/i2c/pxa-i2c.h>
#include <linux/serial_8250.h>
#include <linux/smc91x.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/usb/isp116x.h>
#include <linux/mtd/mtd.h>
.lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
};
+static struct pwm_lookup viper_pwm_lookup[] = {
+ PWM_LOOKUP("pxa25x-pwm.0", 0, "pwm-backlight.0", NULL, 1000000,
+ PWM_POLARITY_NORMAL),
+};
+
static int viper_backlight_init(struct device *dev)
{
int ret;
}
static struct platform_pwm_backlight_data viper_backlight_data = {
- .pwm_id = 0,
.max_brightness = 100,
.dft_brightness = 100,
- .pwm_period_ns = 1000000,
.enable_gpio = -1,
.init = viper_backlight_init,
.notify = viper_backlight_notify,
smc91x_device.num_resources--;
pxa_set_i2c_info(NULL);
+ pwm_add_table(viper_pwm_lookup, ARRAY_SIZE(viper_pwm_lookup));
platform_add_devices(viper_devs, ARRAY_SIZE(viper_devs));
viper_init_vcore_gpios();
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/z2_battery.h>
#include <linux/dma-mapping.h>
* Backlight
******************************************************************************/
#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
+static struct pwm_lookup z2_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.1", 0, "pwm-backlight.0", NULL, 1260320,
+ PWM_POLARITY_NORMAL),
+ PWM_LOOKUP("pxa27x-pwm.0", 1, "pwm-backlight.1", NULL, 1260320,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data z2_backlight_data[] = {
[0] = {
/* Keypad Backlight */
- .pwm_id = 1,
.max_brightness = 1023,
.dft_brightness = 0,
- .pwm_period_ns = 1260320,
.enable_gpio = -1,
},
[1] = {
/* LCD Backlight */
- .pwm_id = 2,
.max_brightness = 1023,
.dft_brightness = 512,
- .pwm_period_ns = 1260320,
.enable_gpio = -1,
},
};
};
static void __init z2_pwm_init(void)
{
+ pwm_add_table(z2_pwm_lookup, ARRAY_SIZE(z2_pwm_lookup));
platform_device_register(&z2_backlight_devices[0]);
platform_device_register(&z2_backlight_devices[1]);
}
};
static struct pxa2xx_spi_master pxa_ssp1_master_info = {
- .clock_enable = CKEN_SSP,
.num_chipselect = 1,
.enable_dma = 1,
};
static struct pxa2xx_spi_master pxa_ssp2_master_info = {
- .clock_enable = CKEN_SSP2,
.num_chipselect = 1,
};
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/smc91x.h>
#endif
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
+static struct pwm_lookup zylonite_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.1", 1, "pwm-backlight.0", NULL, 10000,
+ PWM_POLARITY_NORMAL),
+};
+
static struct platform_pwm_backlight_data zylonite_backlight_data = {
- .pwm_id = 3,
.max_brightness = 100,
.dft_brightness = 100,
- .pwm_period_ns = 10000,
.enable_gpio = -1,
};
static void __init zylonite_init_lcd(void)
{
+ pwm_add_table(zylonite_pwm_lookup, ARRAY_SIZE(zylonite_pwm_lookup));
platform_device_register(&zylonite_backlight_device);
if (lcd_id & 0x20) {
static DEFINE_SPINLOCK(boot_lock);
#ifdef CONFIG_HOTPLUG_CPU
-static void __ref qcom_cpu_die(unsigned int cpu)
+static void qcom_cpu_die(unsigned int cpu)
{
wfi();
}
*
* Called with IRQs disabled
*/
-void __ref realview_cpu_die(unsigned int cpu)
+void realview_cpu_die(unsigned int cpu)
{
int spurious = 0;
comment "Renesas ARM SoCs System Configuration"
endif
-
-if ARCH_SHMOBILE_LEGACY
-
-comment "Renesas ARM SoCs System Type"
-
-config ARCH_R8A7778
- bool "R-Car M1A (R8A77781)"
- select ARCH_RCAR_GEN1
- select ARCH_WANT_OPTIONAL_GPIOLIB
- select ARM_GIC
-
-config ARCH_R8A7779
- bool "R-Car H1 (R8A77790)"
- select ARCH_RCAR_GEN1
- select ARCH_WANT_OPTIONAL_GPIOLIB
- select ARM_GIC
-
-comment "Renesas ARM SoCs Board Type"
-
-config MACH_BOCKW
- bool "BOCK-W platform"
- depends on ARCH_R8A7778
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select SND_SOC_AK4554 if SND_SIMPLE_CARD
- select SND_SOC_AK4642 if SND_SIMPLE_CARD && I2C
- select USE_OF
-
-config MACH_BOCKW_REFERENCE
- bool "BOCK-W - Reference Device Tree Implementation"
- depends on ARCH_R8A7778
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select USE_OF
- ---help---
- Use reference implementation of BockW board support
- which makes use of device tree at the expense
- of not supporting a number of devices.
-
- This is intended to aid developers
-
-comment "Renesas ARM SoCs System Configuration"
-
-config CPU_HAS_INTEVT
- bool
- default y
-
-config SH_CLK_CPG
- bool
-
-source "drivers/sh/Kconfig"
-
-endif
-
-if ARCH_SHMOBILE
-
-menu "Timer and clock configuration"
-
-config SHMOBILE_TIMER_HZ
- int "Kernel HZ (jiffies per second)"
- range 32 1024
- default "128"
- help
- Allows the configuration of the timer frequency. It is customary
- to have the timer interrupt run at 1000 Hz or 100 Hz, but in the
- case of low timer frequencies other values may be more suitable.
- Renesas ARM SoC systems using a 32768 Hz RCLK for clock events may
- want to select a HZ value such as 128 that can evenly divide RCLK.
- A HZ value that does not divide evenly may cause timer drift.
-
-endmenu
-
-endif
#
# Common objects
-obj-y := timer.o console.o
+obj-y := timer.o
# CPU objects
obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o
obj-$(CONFIG_ARCH_EMEV2) += setup-emev2.o
obj-$(CONFIG_ARCH_R7S72100) += setup-r7s72100.o
-# Clock objects
-ifndef CONFIG_COMMON_CLK
-obj-y += clock.o
-obj-$(CONFIG_ARCH_R8A7778) += clock-r8a7778.o
-endif
-
# CPU reset vector handling objects
cpu-y := platsmp.o headsmp.o
obj-$(CONFIG_PM_RMOBILE) += pm-rmobile.o
obj-$(CONFIG_ARCH_RCAR_GEN2) += pm-rcar-gen2.o
-# Board objects
-ifndef CONFIG_ARCH_SHMOBILE_MULTI
-obj-$(CONFIG_MACH_BOCKW) += board-bockw.o
-obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
-endif
-
# Framework support
obj-$(CONFIG_SMP) += $(smp-y)
+++ /dev/null
-# per-board load address for uImage
-loadaddr-y :=
-loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
-loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
-
-__ZRELADDR := $(sort $(loadaddr-y))
- zreladdr-y += $(__ZRELADDR)
-
-# Unsupported legacy stuff
-#
-#params_phys-y (Instead: Pass atags pointer in r2)
-#initrd_phys-y (Instead: Use compiled-in initramfs)
+++ /dev/null
-/*
- * Bock-W board support
- *
- * Copyright (C) 2013 Renesas Solutions Corp.
- * Copyright (C) 2013 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/of_platform.h>
-
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "r8a7778.h"
-
-/*
- * see board-bock.c for checking detail of dip-switch
- */
-
-#define FPGA 0x18200000
-#define IRQ0MR 0x30
-#define COMCTLR 0x101c
-
-#define PFC 0xfffc0000
-#define PUPR4 0x110
-static void __init bockw_init(void)
-{
- void __iomem *fpga;
- void __iomem *pfc;
-
-#ifndef CONFIG_COMMON_CLK
- r8a7778_clock_init();
-#endif
- r8a7778_init_irq_extpin_dt(1);
- r8a7778_add_dt_devices();
-
- fpga = ioremap_nocache(FPGA, SZ_1M);
- if (fpga) {
- /*
- * CAUTION
- *
- * IRQ0/1 is cascaded interrupt from FPGA.
- * it should be cared in the future
- * Now, it is assuming IRQ0 was used only from SMSC.
- */
- u16 val = ioread16(fpga + IRQ0MR);
- val &= ~(1 << 4); /* enable SMSC911x */
- iowrite16(val, fpga + IRQ0MR);
-
- iounmap(fpga);
- }
-
- pfc = ioremap_nocache(PFC, 0x200);
- if (pfc) {
- /*
- * FIXME
- *
- * SDHI CD/WP pin needs pull-up
- */
- iowrite32(ioread32(pfc + PUPR4) | (3 << 26), pfc + PUPR4);
- iounmap(pfc);
- }
-
- of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-}
-
-static const char *const bockw_boards_compat_dt[] __initconst = {
- "renesas,bockw-reference",
- NULL,
-};
-
-DT_MACHINE_START(BOCKW_DT, "bockw")
- .init_early = shmobile_init_delay,
- .init_irq = r8a7778_init_irq_dt,
- .init_machine = bockw_init,
- .init_late = shmobile_init_late,
- .dt_compat = bockw_boards_compat_dt,
-MACHINE_END
+++ /dev/null
-/*
- * Bock-W board support
- *
- * Copyright (C) 2013-2014 Renesas Solutions Corp.
- * Copyright (C) 2013 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- * Copyright (C) 2013-2014 Cogent Embedded, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/mfd/tmio.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sh_mobile_sdhi.h>
-#include <linux/mmc/sh_mmcif.h>
-#include <linux/mtd/partitions.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/platform_data/camera-rcar.h>
-#include <linux/platform_data/usb-rcar-phy.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/smsc911x.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#include <linux/usb/renesas_usbhs.h>
-
-#include <media/soc_camera.h>
-#include <asm/mach/arch.h>
-#include <sound/rcar_snd.h>
-#include <sound/simple_card.h>
-
-#include "common.h"
-#include "irqs.h"
-#include "r8a7778.h"
-
-#define FPGA 0x18200000
-#define IRQ0MR 0x30
-#define COMCTLR 0x101c
-static void __iomem *fpga;
-
-/*
- * CN9(Upper side) SCIF/RCAN selection
- *
- * 1,4 3,6
- * SW40 SCIF RCAN
- * SW41 SCIF RCAN
- */
-
-/*
- * MMC (CN26) pin
- *
- * SW6 (D2) 3 pin
- * SW7 (D5) ON
- * SW8 (D3) 3 pin
- * SW10 (D4) 1 pin
- * SW12 (CLK) 1 pin
- * SW13 (D6) 3 pin
- * SW14 (CMD) ON
- * SW15 (D6) 1 pin
- * SW16 (D0) ON
- * SW17 (D1) ON
- * SW18 (D7) 3 pin
- * SW19 (MMC) 1 pin
- */
-
-/*
- * SSI settings
- *
- * SW45: 1-4 side (SSI5 out, ROUT/LOUT CN19 Mid)
- * SW46: 1101 (SSI6 Recorde)
- * SW47: 1110 (SSI5 Playback)
- * SW48: 11 (Recorde power)
- * SW49: 1 (SSI slave mode)
- * SW50: 1111 (SSI7, SSI8)
- * SW51: 1111 (SSI3, SSI4)
- * SW54: 1pin (ak4554 FPGA control)
- * SW55: 1 (CLKB is 24.5760MHz)
- * SW60: 1pin (ak4554 FPGA control)
- * SW61: 3pin (use X11 clock)
- * SW78: 3-6 (ak4642 connects I2C0)
- *
- * You can use sound as
- *
- * hw0: CN19: SSI56-AK4643
- * hw1: CN21: SSI3-AK4554(playback)
- * hw2: CN21: SSI4-AK4554(capture)
- * hw3: CN20: SSI7-AK4554(playback)
- * hw4: CN20: SSI8-AK4554(capture)
- *
- * this command is required when playback on hw0.
- *
- * # amixer set "LINEOUT Mixer DACL" on
- */
-
-/*
- * USB
- *
- * USB1 (CN29) can be Host/Function
- *
- * Host Func
- * SW98 1 2
- * SW99 1 3
- */
-
-/* Dummy supplies, where voltage doesn't matter */
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
-};
-
-static struct regulator_consumer_supply fixed3v3_power_consumers[] = {
- REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
- REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
-};
-
-static struct smsc911x_platform_config smsc911x_data __initdata = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
- .flags = SMSC911X_USE_32BIT,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource smsc911x_resources[] __initdata = {
- DEFINE_RES_MEM(0x18300000, 0x1000),
- DEFINE_RES_IRQ(irq_pin(0)), /* IRQ 0 */
-};
-
-#if IS_ENABLED(CONFIG_USB_RENESAS_USBHS_UDC)
-/*
- * When USB1 is Func
- */
-static int usbhsf_get_id(struct platform_device *pdev)
-{
- return USBHS_GADGET;
-}
-
-#define SUSPMODE 0x102
-static int usbhsf_power_ctrl(struct platform_device *pdev,
- void __iomem *base, int enable)
-{
- enable = !!enable;
-
- r8a7778_usb_phy_power(enable);
-
- iowrite16(enable << 14, base + SUSPMODE);
-
- return 0;
-}
-
-static struct resource usbhsf_resources[] __initdata = {
- DEFINE_RES_MEM(0xffe60000, 0x110),
- DEFINE_RES_IRQ(gic_iid(0x4f)),
-};
-
-static struct renesas_usbhs_platform_info usbhs_info __initdata = {
- .platform_callback = {
- .get_id = usbhsf_get_id,
- .power_ctrl = usbhsf_power_ctrl,
- },
- .driver_param = {
- .buswait_bwait = 4,
- .d0_tx_id = HPBDMA_SLAVE_USBFUNC_TX,
- .d1_rx_id = HPBDMA_SLAVE_USBFUNC_RX,
- },
-};
-
-#define USB_PHY_SETTING {.port1_func = 1, .ovc_pin[1].active_high = 1,}
-#define USB1_DEVICE "renesas_usbhs"
-#define ADD_USB_FUNC_DEVICE_IF_POSSIBLE() \
- platform_device_register_resndata( \
- NULL, "renesas_usbhs", -1, \
- usbhsf_resources, \
- ARRAY_SIZE(usbhsf_resources), \
- &usbhs_info, sizeof(struct renesas_usbhs_platform_info))
-
-#else
-/*
- * When USB1 is Host
- */
-#define USB_PHY_SETTING { }
-#define USB1_DEVICE "ehci-platform"
-#define ADD_USB_FUNC_DEVICE_IF_POSSIBLE()
-
-#endif
-
-/* USB */
-static struct resource usb_phy_resources[] __initdata = {
- DEFINE_RES_MEM(0xffe70800, 0x100),
- DEFINE_RES_MEM(0xffe76000, 0x100),
-};
-
-static struct rcar_phy_platform_data usb_phy_platform_data __initdata =
- USB_PHY_SETTING;
-
-
-/* SDHI */
-static struct tmio_mmc_data sdhi0_info __initdata = {
- .chan_priv_tx = (void *)HPBDMA_SLAVE_SDHI0_TX,
- .chan_priv_rx = (void *)HPBDMA_SLAVE_SDHI0_RX,
- .capabilities = MMC_CAP_SD_HIGHSPEED,
- .ocr_mask = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
- .flags = TMIO_MMC_HAS_IDLE_WAIT,
-};
-
-static struct resource sdhi0_resources[] __initdata = {
- DEFINE_RES_MEM(0xFFE4C000, 0x100),
- DEFINE_RES_IRQ(gic_iid(0x77)),
-};
-
-/* Ether */
-static struct resource ether_resources[] __initdata = {
- DEFINE_RES_MEM(0xfde00000, 0x400),
- DEFINE_RES_IRQ(gic_iid(0x89)),
-};
-
-static struct sh_eth_plat_data ether_platform_data __initdata = {
- .phy = 0x01,
- .edmac_endian = EDMAC_LITTLE_ENDIAN,
- .phy_interface = PHY_INTERFACE_MODE_RMII,
- /*
- * Although the LINK signal is available on the board, it's connected to
- * the link/activity LED output of the PHY, thus the link disappears and
- * reappears after each packet. We'd be better off ignoring such signal
- * and getting the link state from the PHY indirectly.
- */
- .no_ether_link = 1,
-};
-
-static struct platform_device_info ether_info __initdata = {
- .name = "r8a777x-ether",
- .id = -1,
- .res = ether_resources,
- .num_res = ARRAY_SIZE(ether_resources),
- .data = ðer_platform_data,
- .size_data = sizeof(ether_platform_data),
- .dma_mask = DMA_BIT_MASK(32),
-};
-
-/* I2C */
-static struct i2c_board_info i2c0_devices[] = {
- {
- I2C_BOARD_INFO("rx8581", 0x51),
- }, {
- I2C_BOARD_INFO("ak4643", 0x12),
- }
-};
-
-/* HSPI*/
-static struct mtd_partition m25p80_spi_flash_partitions[] = {
- {
- .name = "data(spi)",
- .size = 0x0100000,
- .offset = 0,
- },
-};
-
-static struct flash_platform_data spi_flash_data = {
- .name = "m25p80",
- .type = "s25fl008k",
- .parts = m25p80_spi_flash_partitions,
- .nr_parts = ARRAY_SIZE(m25p80_spi_flash_partitions),
-};
-
-static struct spi_board_info spi_board_info[] __initdata = {
- {
- .modalias = "m25p80",
- .max_speed_hz = 104000000,
- .chip_select = 0,
- .bus_num = 0,
- .mode = SPI_MODE_0,
- .platform_data = &spi_flash_data,
- },
-};
-
-/* MMC */
-static struct resource mmc_resources[] __initdata = {
- DEFINE_RES_MEM(0xffe4e000, 0x100),
- DEFINE_RES_IRQ(gic_iid(0x5d)),
-};
-
-static struct sh_mmcif_plat_data sh_mmcif_plat __initdata = {
- .sup_pclk = 0,
- .caps = MMC_CAP_4_BIT_DATA |
- MMC_CAP_8_BIT_DATA |
- MMC_CAP_NEEDS_POLL,
-};
-
-/* In the default configuration both decoders reside on I2C bus 0 */
-#define BOCKW_CAMERA(idx) \
-static struct i2c_board_info camera##idx##_info = { \
- I2C_BOARD_INFO("ml86v7667", 0x41 + 2 * (idx)), \
-}; \
- \
-static struct soc_camera_link iclink##idx##_ml86v7667 __initdata = { \
- .bus_id = idx, \
- .i2c_adapter_id = 0, \
- .board_info = &camera##idx##_info, \
-}
-
-BOCKW_CAMERA(0);
-BOCKW_CAMERA(1);
-
-/* VIN */
-static struct rcar_vin_platform_data vin_platform_data __initdata = {
- .flags = RCAR_VIN_BT656,
-};
-
-#define R8A7778_VIN(idx) \
-static struct resource vin##idx##_resources[] __initdata = { \
- DEFINE_RES_MEM(0xffc50000 + 0x1000 * (idx), 0x1000), \
- DEFINE_RES_IRQ(gic_iid(0x5a)), \
-}; \
- \
-static struct platform_device_info vin##idx##_info __initdata = { \
- .name = "r8a7778-vin", \
- .id = idx, \
- .res = vin##idx##_resources, \
- .num_res = ARRAY_SIZE(vin##idx##_resources), \
- .dma_mask = DMA_BIT_MASK(32), \
- .data = &vin_platform_data, \
- .size_data = sizeof(vin_platform_data), \
-}
-R8A7778_VIN(0);
-R8A7778_VIN(1);
-
-/* Sound */
-static struct resource rsnd_resources[] __initdata = {
- [RSND_GEN1_SRU] = DEFINE_RES_MEM(0xffd90000, 0x1000),
- [RSND_GEN1_SSI] = DEFINE_RES_MEM(0xffd91000, 0x1240),
- [RSND_GEN1_ADG] = DEFINE_RES_MEM(0xfffe0000, 0x24),
-};
-
-static struct rsnd_ssi_platform_info rsnd_ssi[] = {
- RSND_SSI_UNUSED, /* SSI 0 */
- RSND_SSI_UNUSED, /* SSI 1 */
- RSND_SSI_UNUSED, /* SSI 2 */
- RSND_SSI(HPBDMA_SLAVE_HPBIF3_TX, gic_iid(0x85), 0),
- RSND_SSI(HPBDMA_SLAVE_HPBIF4_RX, gic_iid(0x85), RSND_SSI_CLK_PIN_SHARE),
- RSND_SSI(HPBDMA_SLAVE_HPBIF5_TX, gic_iid(0x86), 0),
- RSND_SSI(HPBDMA_SLAVE_HPBIF6_RX, gic_iid(0x86), 0),
- RSND_SSI(HPBDMA_SLAVE_HPBIF7_TX, gic_iid(0x86), 0),
- RSND_SSI(HPBDMA_SLAVE_HPBIF8_RX, gic_iid(0x86), RSND_SSI_CLK_PIN_SHARE),
-};
-
-static struct rsnd_src_platform_info rsnd_src[9] = {
- RSND_SRC_UNUSED, /* SRU 0 */
- RSND_SRC_UNUSED, /* SRU 1 */
- RSND_SRC_UNUSED, /* SRU 2 */
- RSND_SRC(0, 0),
- RSND_SRC(0, 0),
- RSND_SRC(0, 0),
- RSND_SRC(0, 0),
- RSND_SRC(0, 0),
- RSND_SRC(0, 0),
-};
-
-static struct rsnd_dai_platform_info rsnd_dai[] = {
- {
- .playback = { .ssi = &rsnd_ssi[5], .src = &rsnd_src[5] },
- .capture = { .ssi = &rsnd_ssi[6], .src = &rsnd_src[6] },
- }, {
- .playback = { .ssi = &rsnd_ssi[3], .src = &rsnd_src[3] },
- }, {
- .capture = { .ssi = &rsnd_ssi[4], .src = &rsnd_src[4] },
- }, {
- .playback = { .ssi = &rsnd_ssi[7], .src = &rsnd_src[7] },
- }, {
- .capture = { .ssi = &rsnd_ssi[8], .src = &rsnd_src[8] },
- },
-};
-
-enum {
- AK4554_34 = 0,
- AK4643_56,
- AK4554_78,
- SOUND_MAX,
-};
-
-static int rsnd_codec_power(int id, int enable)
-{
- static int sound_user[SOUND_MAX] = {0, 0, 0};
- int *usr = NULL;
- u32 bit;
-
- switch (id) {
- case 3:
- case 4:
- usr = sound_user + AK4554_34;
- bit = (1 << 10);
- break;
- case 5:
- case 6:
- usr = sound_user + AK4643_56;
- bit = (1 << 6);
- break;
- case 7:
- case 8:
- usr = sound_user + AK4554_78;
- bit = (1 << 7);
- break;
- }
-
- if (!usr)
- return -EIO;
-
- if (enable) {
- if (*usr == 0) {
- u32 val = ioread16(fpga + COMCTLR);
- val &= ~bit;
- iowrite16(val, fpga + COMCTLR);
- }
-
- (*usr)++;
- } else {
- if (*usr == 0)
- return 0;
-
- (*usr)--;
-
- if (*usr == 0) {
- u32 val = ioread16(fpga + COMCTLR);
- val |= bit;
- iowrite16(val, fpga + COMCTLR);
- }
- }
-
- return 0;
-}
-
-static int rsnd_start(int id)
-{
- return rsnd_codec_power(id, 1);
-}
-
-static int rsnd_stop(int id)
-{
- return rsnd_codec_power(id, 0);
-}
-
-static struct rcar_snd_info rsnd_info = {
- .flags = RSND_GEN1,
- .ssi_info = rsnd_ssi,
- .ssi_info_nr = ARRAY_SIZE(rsnd_ssi),
- .src_info = rsnd_src,
- .src_info_nr = ARRAY_SIZE(rsnd_src),
- .dai_info = rsnd_dai,
- .dai_info_nr = ARRAY_SIZE(rsnd_dai),
- .start = rsnd_start,
- .stop = rsnd_stop,
-};
-
-static struct asoc_simple_card_info rsnd_card_info[] = {
- /* SSI5, SSI6 */
- {
- .name = "AK4643",
- .card = "SSI56-AK4643",
- .codec = "ak4642-codec.0-0012",
- .platform = "rcar_sound",
- .daifmt = SND_SOC_DAIFMT_LEFT_J | SND_SOC_DAIFMT_CBM_CFM,
- .cpu_dai = {
- .name = "rsnd-dai.0",
- },
- .codec_dai = {
- .name = "ak4642-hifi",
- .sysclk = 11289600,
- },
- },
- /* SSI3 */
- {
- .name = "AK4554",
- .card = "SSI3-AK4554(playback)",
- .codec = "ak4554-adc-dac.0",
- .platform = "rcar_sound",
- .daifmt = SND_SOC_DAIFMT_CBS_CFS | SND_SOC_DAIFMT_RIGHT_J,
- .cpu_dai = {
- .name = "rsnd-dai.1",
- },
- .codec_dai = {
- .name = "ak4554-hifi",
- },
- },
- /* SSI4 */
- {
- .name = "AK4554",
- .card = "SSI4-AK4554(capture)",
- .codec = "ak4554-adc-dac.0",
- .platform = "rcar_sound",
- .daifmt = SND_SOC_DAIFMT_CBS_CFS | SND_SOC_DAIFMT_LEFT_J,
- .cpu_dai = {
- .name = "rsnd-dai.2",
- },
- .codec_dai = {
- .name = "ak4554-hifi",
- },
- },
- /* SSI7 */
- {
- .name = "AK4554",
- .card = "SSI7-AK4554(playback)",
- .codec = "ak4554-adc-dac.1",
- .platform = "rcar_sound",
- .daifmt = SND_SOC_DAIFMT_CBS_CFS | SND_SOC_DAIFMT_RIGHT_J,
- .cpu_dai = {
- .name = "rsnd-dai.3",
- },
- .codec_dai = {
- .name = "ak4554-hifi",
- },
- },
- /* SSI8 */
- {
- .name = "AK4554",
- .card = "SSI8-AK4554(capture)",
- .codec = "ak4554-adc-dac.1",
- .platform = "rcar_sound",
- .daifmt = SND_SOC_DAIFMT_CBS_CFS | SND_SOC_DAIFMT_LEFT_J,
- .cpu_dai = {
- .name = "rsnd-dai.4",
- },
- .codec_dai = {
- .name = "ak4554-hifi",
- },
- }
-};
-
-static const struct pinctrl_map bockw_pinctrl_map[] = {
- /* AUDIO */
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "audio_clk_a", "audio_clk"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "audio_clk_b", "audio_clk"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi34_ctrl", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi3_data", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi4_data", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi5_ctrl", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi5_data", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi6_ctrl", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi6_data", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi78_ctrl", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi7_data", "ssi"),
- PIN_MAP_MUX_GROUP_DEFAULT("rcar_sound", "pfc-r8a7778",
- "ssi8_data", "ssi"),
- /* Ether */
- PIN_MAP_MUX_GROUP_DEFAULT("r8a777x-ether", "pfc-r8a7778",
- "ether_rmii", "ether"),
- /* HSPI0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-hspi.0", "pfc-r8a7778",
- "hspi0_a", "hspi0"),
- /* MMC */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif", "pfc-r8a7778",
- "mmc_data8", "mmc"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif", "pfc-r8a7778",
- "mmc_ctrl", "mmc"),
- /* SCIF0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a7778",
- "scif0_data_a", "scif0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a7778",
- "scif0_ctrl", "scif0"),
- /* USB */
- PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
- "usb0", "usb0"),
- PIN_MAP_MUX_GROUP_DEFAULT(USB1_DEVICE, "pfc-r8a7778",
- "usb1", "usb1"),
- /* SDHI0 */
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
- "sdhi0_data4", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
- "sdhi0_ctrl", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
- "sdhi0_cd", "sdhi0"),
- PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
- "sdhi0_wp", "sdhi0"),
- /* VIN0 */
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7778-vin.0", "pfc-r8a7778",
- "vin0_clk", "vin0"),
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7778-vin.0", "pfc-r8a7778",
- "vin0_data8", "vin0"),
- /* VIN1 */
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7778-vin.1", "pfc-r8a7778",
- "vin1_clk", "vin1"),
- PIN_MAP_MUX_GROUP_DEFAULT("r8a7778-vin.1", "pfc-r8a7778",
- "vin1_data8", "vin1"),
-};
-
-#define PFC 0xfffc0000
-#define PUPR4 0x110
-static void __init bockw_init(void)
-{
- void __iomem *base;
- struct clk *clk;
- struct platform_device *pdev;
- int i;
-
- r8a7778_clock_init();
- r8a7778_init_irq_extpin(1);
- r8a7778_add_standard_devices();
-
- platform_device_register_full(ðer_info);
-
- platform_device_register_full(&vin0_info);
- /* VIN1 has a pin conflict with Ether */
- if (!IS_ENABLED(CONFIG_SH_ETH))
- platform_device_register_full(&vin1_info);
- platform_device_register_data(NULL, "soc-camera-pdrv", 0,
- &iclink0_ml86v7667,
- sizeof(iclink0_ml86v7667));
- platform_device_register_data(NULL, "soc-camera-pdrv", 1,
- &iclink1_ml86v7667,
- sizeof(iclink1_ml86v7667));
-
- i2c_register_board_info(0, i2c0_devices,
- ARRAY_SIZE(i2c0_devices));
- spi_register_board_info(spi_board_info,
- ARRAY_SIZE(spi_board_info));
- pinctrl_register_mappings(bockw_pinctrl_map,
- ARRAY_SIZE(bockw_pinctrl_map));
- r8a7778_pinmux_init();
-
- platform_device_register_resndata(
- NULL, "sh_mmcif", -1,
- mmc_resources, ARRAY_SIZE(mmc_resources),
- &sh_mmcif_plat, sizeof(struct sh_mmcif_plat_data));
-
- platform_device_register_resndata(
- NULL, "rcar_usb_phy", -1,
- usb_phy_resources,
- ARRAY_SIZE(usb_phy_resources),
- &usb_phy_platform_data,
- sizeof(struct rcar_phy_platform_data));
-
- regulator_register_fixed(0, dummy_supplies,
- ARRAY_SIZE(dummy_supplies));
- regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
- ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
-
- /* for SMSC */
- fpga = ioremap_nocache(FPGA, SZ_1M);
- if (fpga) {
- /*
- * CAUTION
- *
- * IRQ0/1 is cascaded interrupt from FPGA.
- * it should be cared in the future
- * Now, it is assuming IRQ0 was used only from SMSC.
- */
- u16 val = ioread16(fpga + IRQ0MR);
- val &= ~(1 << 4); /* enable SMSC911x */
- iowrite16(val, fpga + IRQ0MR);
-
- platform_device_register_resndata(
- NULL, "smsc911x", -1,
- smsc911x_resources, ARRAY_SIZE(smsc911x_resources),
- &smsc911x_data, sizeof(smsc911x_data));
- }
-
- /* for SDHI */
- base = ioremap_nocache(PFC, 0x200);
- if (base) {
- /*
- * FIXME
- *
- * SDHI CD/WP pin needs pull-up
- */
- iowrite32(ioread32(base + PUPR4) | (3 << 26), base + PUPR4);
- iounmap(base);
-
- platform_device_register_resndata(
- NULL, "sh_mobile_sdhi", 0,
- sdhi0_resources, ARRAY_SIZE(sdhi0_resources),
- &sdhi0_info, sizeof(struct tmio_mmc_data));
- }
-
- /* for Audio */
- rsnd_codec_power(5, 1); /* enable ak4642 */
-
- platform_device_register_simple(
- "ak4554-adc-dac", 0, NULL, 0);
-
- platform_device_register_simple(
- "ak4554-adc-dac", 1, NULL, 0);
-
- pdev = platform_device_register_resndata(
- NULL, "rcar_sound", -1,
- rsnd_resources, ARRAY_SIZE(rsnd_resources),
- &rsnd_info, sizeof(rsnd_info));
-
- clk = clk_get(&pdev->dev, "clk_b");
- clk_set_rate(clk, 24576000);
- clk_put(clk);
-
- for (i = 0; i < ARRAY_SIZE(rsnd_card_info); i++) {
- struct platform_device_info cardinfo = {
- .name = "asoc-simple-card",
- .id = i,
- .data = &rsnd_card_info[i],
- .size_data = sizeof(struct asoc_simple_card_info),
- .dma_mask = DMA_BIT_MASK(32),
- };
-
- platform_device_register_full(&cardinfo);
- }
-}
-
-static void __init bockw_init_late(void)
-{
- r8a7778_init_late();
- ADD_USB_FUNC_DEVICE_IF_POSSIBLE();
-}
-
-static const char *const bockw_boards_compat_dt[] __initconst = {
- "renesas,bockw",
- NULL,
-};
-
-DT_MACHINE_START(BOCKW_DT, "bockw")
- .init_early = shmobile_init_delay,
- .init_irq = r8a7778_init_irq_dt,
- .init_machine = bockw_init,
- .dt_compat = bockw_boards_compat_dt,
- .init_late = bockw_init_late,
-MACHINE_END
+++ /dev/null
-/*
- * r8a7778 clock framework support
- *
- * Copyright (C) 2013 Renesas Solutions Corp.
- * Copyright (C) 2013 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * based on r8a7779
- *
- * Copyright (C) 2011 Renesas Solutions Corp.
- * Copyright (C) 2011 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-/*
- * MD MD MD MD PLLA PLLB EXTAL clki clkz
- * 19 18 12 11 (HMz) (MHz) (MHz)
- *----------------------------------------------------------------------------
- * 1 0 0 0 x21 x21 38.00 800 800
- * 1 0 0 1 x24 x24 33.33 800 800
- * 1 0 1 0 x28 x28 28.50 800 800
- * 1 0 1 1 x32 x32 25.00 800 800
- * 1 1 0 1 x24 x21 33.33 800 700
- * 1 1 1 0 x28 x21 28.50 800 600
- * 1 1 1 1 x32 x24 25.00 800 600
- */
-
-#include <linux/io.h>
-#include <linux/sh_clk.h>
-#include <linux/clkdev.h>
-#include "clock.h"
-#include "common.h"
-
-#define MSTPCR0 IOMEM(0xffc80030)
-#define MSTPCR1 IOMEM(0xffc80034)
-#define MSTPCR3 IOMEM(0xffc8003c)
-#define MSTPSR1 IOMEM(0xffc80044)
-#define MSTPSR4 IOMEM(0xffc80048)
-#define MSTPSR6 IOMEM(0xffc8004c)
-#define MSTPCR4 IOMEM(0xffc80050)
-#define MSTPCR5 IOMEM(0xffc80054)
-#define MSTPCR6 IOMEM(0xffc80058)
-#define MODEMR 0xFFCC0020
-
-#define MD(nr) BIT(nr)
-
-/* ioremap() through clock mapping mandatory to avoid
- * collision with ARM coherent DMA virtual memory range.
- */
-
-static struct clk_mapping cpg_mapping = {
- .phys = 0xffc80000,
- .len = 0x80,
-};
-
-static struct clk extal_clk = {
- /* .rate will be updated on r8a7778_clock_init() */
- .mapping = &cpg_mapping,
-};
-
-static struct clk audio_clk_a = {
-};
-
-static struct clk audio_clk_b = {
-};
-
-static struct clk audio_clk_c = {
-};
-
-/*
- * clock ratio of these clock will be updated
- * on r8a7778_clock_init()
- */
-SH_FIXED_RATIO_CLK_SET(plla_clk, extal_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(pllb_clk, extal_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(i_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(s_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(s1_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(s3_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(s4_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(b_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(out_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(p_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(g_clk, plla_clk, 1, 1);
-SH_FIXED_RATIO_CLK_SET(z_clk, pllb_clk, 1, 1);
-
-static struct clk *main_clks[] = {
- &extal_clk,
- &plla_clk,
- &pllb_clk,
- &i_clk,
- &s_clk,
- &s1_clk,
- &s3_clk,
- &s4_clk,
- &b_clk,
- &out_clk,
- &p_clk,
- &g_clk,
- &z_clk,
- &audio_clk_a,
- &audio_clk_b,
- &audio_clk_c,
-};
-
-enum {
- MSTP531, MSTP530,
- MSTP529, MSTP528, MSTP527, MSTP526, MSTP525, MSTP524, MSTP523,
- MSTP331,
- MSTP323, MSTP322, MSTP321,
- MSTP311, MSTP310,
- MSTP309, MSTP308, MSTP307,
- MSTP114,
- MSTP110, MSTP109,
- MSTP100,
- MSTP030,
- MSTP029, MSTP028, MSTP027, MSTP026, MSTP025, MSTP024, MSTP023, MSTP022, MSTP021,
- MSTP016, MSTP015, MSTP012, MSTP011, MSTP010,
- MSTP009, MSTP008, MSTP007,
- MSTP_NR };
-
-static struct clk mstp_clks[MSTP_NR] = {
- [MSTP531] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 31, 0), /* SCU0 */
- [MSTP530] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 30, 0), /* SCU1 */
- [MSTP529] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 29, 0), /* SCU2 */
- [MSTP528] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 28, 0), /* SCU3 */
- [MSTP527] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 27, 0), /* SCU4 */
- [MSTP526] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 26, 0), /* SCU5 */
- [MSTP525] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 25, 0), /* SCU6 */
- [MSTP524] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 24, 0), /* SCU7 */
- [MSTP523] = SH_CLK_MSTP32(&p_clk, MSTPCR5, 23, 0), /* SCU8 */
- [MSTP331] = SH_CLK_MSTP32(&s4_clk, MSTPCR3, 31, 0), /* MMC */
- [MSTP323] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 23, 0), /* SDHI0 */
- [MSTP322] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 22, 0), /* SDHI1 */
- [MSTP321] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 21, 0), /* SDHI2 */
- [MSTP311] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 11, 0), /* SSI4 */
- [MSTP310] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 10, 0), /* SSI5 */
- [MSTP309] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 9, 0), /* SSI6 */
- [MSTP308] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 8, 0), /* SSI7 */
- [MSTP307] = SH_CLK_MSTP32(&p_clk, MSTPCR3, 7, 0), /* SSI8 */
- [MSTP114] = SH_CLK_MSTP32(&p_clk, MSTPCR1, 14, 0), /* Ether */
- [MSTP110] = SH_CLK_MSTP32(&s_clk, MSTPCR1, 10, 0), /* VIN0 */
- [MSTP109] = SH_CLK_MSTP32(&s_clk, MSTPCR1, 9, 0), /* VIN1 */
- [MSTP100] = SH_CLK_MSTP32(&p_clk, MSTPCR1, 0, 0), /* USB0/1 */
- [MSTP030] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 30, 0), /* I2C0 */
- [MSTP029] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 29, 0), /* I2C1 */
- [MSTP028] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 28, 0), /* I2C2 */
- [MSTP027] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 27, 0), /* I2C3 */
- [MSTP026] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 26, 0), /* SCIF0 */
- [MSTP025] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 25, 0), /* SCIF1 */
- [MSTP024] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 24, 0), /* SCIF2 */
- [MSTP023] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 23, 0), /* SCIF3 */
- [MSTP022] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 22, 0), /* SCIF4 */
- [MSTP021] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 21, 0), /* SCIF5 */
- [MSTP016] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 16, 0), /* TMU0 */
- [MSTP015] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 15, 0), /* TMU1 */
- [MSTP012] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 12, 0), /* SSI0 */
- [MSTP011] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 11, 0), /* SSI1 */
- [MSTP010] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 10, 0), /* SSI2 */
- [MSTP009] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 9, 0), /* SSI3 */
- [MSTP008] = SH_CLK_MSTP32(&p_clk, MSTPCR0, 8, 0), /* SRU */
- [MSTP007] = SH_CLK_MSTP32(&s_clk, MSTPCR0, 7, 0), /* HSPI */
-};
-
-static struct clk_lookup lookups[] = {
- /* main */
- CLKDEV_CON_ID("shyway_clk", &s_clk),
- CLKDEV_CON_ID("peripheral_clk", &p_clk),
-
- /* MSTP32 clocks */
- CLKDEV_DEV_ID("sh_mmcif", &mstp_clks[MSTP331]), /* MMC */
- CLKDEV_DEV_ID("ffe4e000.mmc", &mstp_clks[MSTP331]), /* MMC */
- CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP323]), /* SDHI0 */
- CLKDEV_DEV_ID("ffe4c000.sd", &mstp_clks[MSTP323]), /* SDHI0 */
- CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP322]), /* SDHI1 */
- CLKDEV_DEV_ID("ffe4d000.sd", &mstp_clks[MSTP322]), /* SDHI1 */
- CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP321]), /* SDHI2 */
- CLKDEV_DEV_ID("ffe4f000.sd", &mstp_clks[MSTP321]), /* SDHI2 */
- CLKDEV_DEV_ID("r8a777x-ether", &mstp_clks[MSTP114]), /* Ether */
- CLKDEV_DEV_ID("r8a7778-vin.0", &mstp_clks[MSTP110]), /* VIN0 */
- CLKDEV_DEV_ID("r8a7778-vin.1", &mstp_clks[MSTP109]), /* VIN1 */
- CLKDEV_DEV_ID("ehci-platform", &mstp_clks[MSTP100]), /* USB EHCI port0/1 */
- CLKDEV_DEV_ID("ohci-platform", &mstp_clks[MSTP100]), /* USB OHCI port0/1 */
- CLKDEV_DEV_ID("renesas_usbhs", &mstp_clks[MSTP100]), /* USB FUNC */
- CLKDEV_DEV_ID("i2c-rcar.0", &mstp_clks[MSTP030]), /* I2C0 */
- CLKDEV_DEV_ID("ffc70000.i2c", &mstp_clks[MSTP030]), /* I2C0 */
- CLKDEV_DEV_ID("i2c-rcar.1", &mstp_clks[MSTP029]), /* I2C1 */
- CLKDEV_DEV_ID("ffc71000.i2c", &mstp_clks[MSTP029]), /* I2C1 */
- CLKDEV_DEV_ID("i2c-rcar.2", &mstp_clks[MSTP028]), /* I2C2 */
- CLKDEV_DEV_ID("ffc72000.i2c", &mstp_clks[MSTP028]), /* I2C2 */
- CLKDEV_DEV_ID("i2c-rcar.3", &mstp_clks[MSTP027]), /* I2C3 */
- CLKDEV_DEV_ID("ffc73000.i2c", &mstp_clks[MSTP027]), /* I2C3 */
- CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP026]), /* SCIF0 */
- CLKDEV_DEV_ID("ffe40000.serial", &mstp_clks[MSTP026]), /* SCIF0 */
- CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP025]), /* SCIF1 */
- CLKDEV_DEV_ID("ffe41000.serial", &mstp_clks[MSTP025]), /* SCIF1 */
- CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP024]), /* SCIF2 */
- CLKDEV_DEV_ID("ffe42000.serial", &mstp_clks[MSTP024]), /* SCIF2 */
- CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP023]), /* SCIF3 */
- CLKDEV_DEV_ID("ffe43000.serial", &mstp_clks[MSTP023]), /* SCIF3 */
- CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP022]), /* SCIF4 */
- CLKDEV_DEV_ID("ffe44000.serial", &mstp_clks[MSTP022]), /* SCIF4 */
- CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP021]), /* SCIF6 */
- CLKDEV_DEV_ID("ffe45000.serial", &mstp_clks[MSTP021]), /* SCIF5 */
- CLKDEV_DEV_ID("sh-hspi.0", &mstp_clks[MSTP007]), /* HSPI0 */
- CLKDEV_DEV_ID("fffc7000.spi", &mstp_clks[MSTP007]), /* HSPI0 */
- CLKDEV_DEV_ID("sh-hspi.1", &mstp_clks[MSTP007]), /* HSPI1 */
- CLKDEV_DEV_ID("fffc8000.spi", &mstp_clks[MSTP007]), /* HSPI1 */
- CLKDEV_DEV_ID("sh-hspi.2", &mstp_clks[MSTP007]), /* HSPI2 */
- CLKDEV_DEV_ID("fffc6000.spi", &mstp_clks[MSTP007]), /* HSPI2 */
- CLKDEV_DEV_ID("rcar_sound", &mstp_clks[MSTP008]), /* SRU */
-
- CLKDEV_ICK_ID("clk_a", "rcar_sound", &audio_clk_a),
- CLKDEV_ICK_ID("clk_b", "rcar_sound", &audio_clk_b),
- CLKDEV_ICK_ID("clk_c", "rcar_sound", &audio_clk_c),
- CLKDEV_ICK_ID("clk_i", "rcar_sound", &s1_clk),
- CLKDEV_ICK_ID("ssi.0", "rcar_sound", &mstp_clks[MSTP012]),
- CLKDEV_ICK_ID("ssi.1", "rcar_sound", &mstp_clks[MSTP011]),
- CLKDEV_ICK_ID("ssi.2", "rcar_sound", &mstp_clks[MSTP010]),
- CLKDEV_ICK_ID("ssi.3", "rcar_sound", &mstp_clks[MSTP009]),
- CLKDEV_ICK_ID("ssi.4", "rcar_sound", &mstp_clks[MSTP311]),
- CLKDEV_ICK_ID("ssi.5", "rcar_sound", &mstp_clks[MSTP310]),
- CLKDEV_ICK_ID("ssi.6", "rcar_sound", &mstp_clks[MSTP309]),
- CLKDEV_ICK_ID("ssi.7", "rcar_sound", &mstp_clks[MSTP308]),
- CLKDEV_ICK_ID("ssi.8", "rcar_sound", &mstp_clks[MSTP307]),
- CLKDEV_ICK_ID("src.0", "rcar_sound", &mstp_clks[MSTP531]),
- CLKDEV_ICK_ID("src.1", "rcar_sound", &mstp_clks[MSTP530]),
- CLKDEV_ICK_ID("src.2", "rcar_sound", &mstp_clks[MSTP529]),
- CLKDEV_ICK_ID("src.3", "rcar_sound", &mstp_clks[MSTP528]),
- CLKDEV_ICK_ID("src.4", "rcar_sound", &mstp_clks[MSTP527]),
- CLKDEV_ICK_ID("src.5", "rcar_sound", &mstp_clks[MSTP526]),
- CLKDEV_ICK_ID("src.6", "rcar_sound", &mstp_clks[MSTP525]),
- CLKDEV_ICK_ID("src.7", "rcar_sound", &mstp_clks[MSTP524]),
- CLKDEV_ICK_ID("src.8", "rcar_sound", &mstp_clks[MSTP523]),
- CLKDEV_ICK_ID("fck", "sh-tmu.0", &mstp_clks[MSTP016]),
- CLKDEV_ICK_ID("fck", "ffd80000.timer", &mstp_clks[MSTP016]),
- CLKDEV_ICK_ID("fck", "sh-tmu.1", &mstp_clks[MSTP015]),
- CLKDEV_ICK_ID("fck", "ffd81000.timer", &mstp_clks[MSTP015]),
-};
-
-void __init r8a7778_clock_init(void)
-{
- void __iomem *modemr = ioremap_nocache(MODEMR, PAGE_SIZE);
- u32 mode;
- int k, ret = 0;
-
- BUG_ON(!modemr);
- mode = ioread32(modemr);
- iounmap(modemr);
-
- switch (mode & (MD(19) | MD(18) | MD(12) | MD(11))) {
- case MD(19):
- extal_clk.rate = 38000000;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 21, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 21, 1);
- break;
- case MD(19) | MD(11):
- extal_clk.rate = 33333333;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 24, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 24, 1);
- break;
- case MD(19) | MD(12):
- extal_clk.rate = 28500000;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 28, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 28, 1);
- break;
- case MD(19) | MD(12) | MD(11):
- extal_clk.rate = 25000000;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 32, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 32, 1);
- break;
- case MD(19) | MD(18) | MD(11):
- extal_clk.rate = 33333333;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 24, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 21, 1);
- break;
- case MD(19) | MD(18) | MD(12):
- extal_clk.rate = 28500000;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 28, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 21, 1);
- break;
- case MD(19) | MD(18) | MD(12) | MD(11):
- extal_clk.rate = 25000000;
- SH_CLK_SET_RATIO(&plla_clk_ratio, 32, 1);
- SH_CLK_SET_RATIO(&pllb_clk_ratio, 24, 1);
- break;
- default:
- BUG();
- }
-
- if (mode & MD(1)) {
- SH_CLK_SET_RATIO(&i_clk_ratio, 1, 1);
- SH_CLK_SET_RATIO(&s_clk_ratio, 1, 3);
- SH_CLK_SET_RATIO(&s1_clk_ratio, 1, 6);
- SH_CLK_SET_RATIO(&s3_clk_ratio, 1, 4);
- SH_CLK_SET_RATIO(&s4_clk_ratio, 1, 8);
- SH_CLK_SET_RATIO(&p_clk_ratio, 1, 12);
- SH_CLK_SET_RATIO(&g_clk_ratio, 1, 12);
- if (mode & MD(2)) {
- SH_CLK_SET_RATIO(&b_clk_ratio, 1, 18);
- SH_CLK_SET_RATIO(&out_clk_ratio, 1, 18);
- } else {
- SH_CLK_SET_RATIO(&b_clk_ratio, 1, 12);
- SH_CLK_SET_RATIO(&out_clk_ratio, 1, 12);
- }
- } else {
- SH_CLK_SET_RATIO(&i_clk_ratio, 1, 1);
- SH_CLK_SET_RATIO(&s_clk_ratio, 1, 4);
- SH_CLK_SET_RATIO(&s1_clk_ratio, 1, 8);
- SH_CLK_SET_RATIO(&s3_clk_ratio, 1, 4);
- SH_CLK_SET_RATIO(&s4_clk_ratio, 1, 8);
- SH_CLK_SET_RATIO(&p_clk_ratio, 1, 16);
- SH_CLK_SET_RATIO(&g_clk_ratio, 1, 12);
- if (mode & MD(2)) {
- SH_CLK_SET_RATIO(&b_clk_ratio, 1, 16);
- SH_CLK_SET_RATIO(&out_clk_ratio, 1, 16);
- } else {
- SH_CLK_SET_RATIO(&b_clk_ratio, 1, 12);
- SH_CLK_SET_RATIO(&out_clk_ratio, 1, 12);
- }
- }
-
- for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
- ret = clk_register(main_clks[k]);
-
- if (!ret)
- ret = sh_clk_mstp_register(mstp_clks, MSTP_NR);
-
- clkdev_add_table(lookups, ARRAY_SIZE(lookups));
-
- if (!ret)
- shmobile_clk_init();
- else
- panic("failed to setup r8a7778 clocks\n");
-}
+++ /dev/null
-/*
- * SH-Mobile Clock Framework
- *
- * Copyright (C) 2010 Magnus Damm
- *
- * Used together with arch/arm/common/clkdev.c and drivers/sh/clk.c.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/export.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/sh_clk.h>
-
-#include "clock.h"
-#include "common.h"
-
-unsigned long shmobile_fixed_ratio_clk_recalc(struct clk *clk)
-{
- struct clk_ratio *p = clk->priv;
-
- return clk->parent->rate / p->div * p->mul;
-};
-
-struct sh_clk_ops shmobile_fixed_ratio_clk_ops = {
- .recalc = shmobile_fixed_ratio_clk_recalc,
-};
-
-int __init shmobile_clk_init(void)
-{
- /* Kick the child clocks.. */
- recalculate_root_clocks();
-
- /* Enable the necessary init clocks */
- clk_enable_init_clocks();
-
- return 0;
-}
+++ /dev/null
-#ifndef CLOCK_H
-#define CLOCK_H
-
-/* legacy clock implementation */
-
-struct clk;
-unsigned long shmobile_fixed_ratio_clk_recalc(struct clk *clk);
-extern struct sh_clk_ops shmobile_fixed_ratio_clk_ops;
-
-/* clock ratio */
-struct clk_ratio {
- int mul;
- int div;
-};
-
-#define SH_CLK_RATIO(name, m, d) \
-static struct clk_ratio name ##_ratio = { \
- .mul = m, \
- .div = d, \
-}
-
-#define SH_FIXED_RATIO_CLKg(name, p, r) \
-struct clk name = { \
- .parent = &p, \
- .ops = &shmobile_fixed_ratio_clk_ops,\
- .priv = &r ## _ratio, \
-}
-
-#define SH_FIXED_RATIO_CLK(name, p, r) \
-static SH_FIXED_RATIO_CLKg(name, p, r)
-
-#define SH_FIXED_RATIO_CLK_SET(name, p, m, d) \
- SH_CLK_RATIO(name, m, d); \
- SH_FIXED_RATIO_CLK(name, p, name)
-
-#define SH_CLK_SET_RATIO(p, m, d) \
-do { \
- (p)->mul = m; \
- (p)->div = d; \
-} while (0)
-
-#endif
#ifndef __ARCH_MACH_COMMON_H
#define __ARCH_MACH_COMMON_H
-extern void shmobile_earlytimer_init(void);
extern void shmobile_init_delay(void);
-struct twd_local_timer;
-extern void shmobile_setup_console(void);
extern void shmobile_boot_vector(void);
extern unsigned long shmobile_boot_fn;
extern unsigned long shmobile_boot_arg;
extern void shmobile_smp_scu_prepare_cpus(unsigned int max_cpus);
extern void shmobile_smp_scu_cpu_die(unsigned int cpu);
extern int shmobile_smp_scu_cpu_kill(unsigned int cpu);
-struct clk;
-extern int shmobile_clk_init(void);
extern struct platform_suspend_ops shmobile_suspend_ops;
#ifdef CONFIG_SUSPEND
+++ /dev/null
-/*
- * SH-Mobile Console
- *
- * Copyright (C) 2010 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <asm/mach/map.h>
-#include "common.h"
-
-void __init shmobile_setup_console(void)
-{
- parse_early_param();
-
- /* Let earlyprintk output early console messages */
- early_platform_driver_probe("earlyprintk", 1, 1);
-}
+++ /dev/null
-#ifndef __ASM_MACH_INTC_H
-#define __ASM_MACH_INTC_H
-#include <linux/sh_intc.h>
-
-#define INTC_IRQ_PINS_ENUM_16L(p) \
- p ## _IRQ0, p ## _IRQ1, p ## _IRQ2, p ## _IRQ3, \
- p ## _IRQ4, p ## _IRQ5, p ## _IRQ6, p ## _IRQ7, \
- p ## _IRQ8, p ## _IRQ9, p ## _IRQ10, p ## _IRQ11, \
- p ## _IRQ12, p ## _IRQ13, p ## _IRQ14, p ## _IRQ15
-
-#define INTC_IRQ_PINS_ENUM_16H(p) \
- p ## _IRQ16, p ## _IRQ17, p ## _IRQ18, p ## _IRQ19, \
- p ## _IRQ20, p ## _IRQ21, p ## _IRQ22, p ## _IRQ23, \
- p ## _IRQ24, p ## _IRQ25, p ## _IRQ26, p ## _IRQ27, \
- p ## _IRQ28, p ## _IRQ29, p ## _IRQ30, p ## _IRQ31
-
-#define INTC_IRQ_PINS_VECT_16L(p, vect) \
- vect(p ## _IRQ0, 0x0200), vect(p ## _IRQ1, 0x0220), \
- vect(p ## _IRQ2, 0x0240), vect(p ## _IRQ3, 0x0260), \
- vect(p ## _IRQ4, 0x0280), vect(p ## _IRQ5, 0x02a0), \
- vect(p ## _IRQ6, 0x02c0), vect(p ## _IRQ7, 0x02e0), \
- vect(p ## _IRQ8, 0x0300), vect(p ## _IRQ9, 0x0320), \
- vect(p ## _IRQ10, 0x0340), vect(p ## _IRQ11, 0x0360), \
- vect(p ## _IRQ12, 0x0380), vect(p ## _IRQ13, 0x03a0), \
- vect(p ## _IRQ14, 0x03c0), vect(p ## _IRQ15, 0x03e0)
-
-#define INTC_IRQ_PINS_VECT_16H(p, vect) \
- vect(p ## _IRQ16, 0x3200), vect(p ## _IRQ17, 0x3220), \
- vect(p ## _IRQ18, 0x3240), vect(p ## _IRQ19, 0x3260), \
- vect(p ## _IRQ20, 0x3280), vect(p ## _IRQ21, 0x32a0), \
- vect(p ## _IRQ22, 0x32c0), vect(p ## _IRQ23, 0x32e0), \
- vect(p ## _IRQ24, 0x3300), vect(p ## _IRQ25, 0x3320), \
- vect(p ## _IRQ26, 0x3340), vect(p ## _IRQ27, 0x3360), \
- vect(p ## _IRQ28, 0x3380), vect(p ## _IRQ29, 0x33a0), \
- vect(p ## _IRQ30, 0x33c0), vect(p ## _IRQ31, 0x33e0)
-
-#define INTC_IRQ_PINS_MASK_16L(p, base) \
- { base + 0x40, base + 0x60, 8, /* INTMSK00A / INTMSKCLR00A */ \
- { p ## _IRQ0, p ## _IRQ1, p ## _IRQ2, p ## _IRQ3, \
- p ## _IRQ4, p ## _IRQ5, p ## _IRQ6, p ## _IRQ7 } }, \
- { base + 0x44, base + 0x64, 8, /* INTMSK10A / INTMSKCLR10A */ \
- { p ## _IRQ8, p ## _IRQ9, p ## _IRQ10, p ## _IRQ11, \
- p ## _IRQ12, p ## _IRQ13, p ## _IRQ14, p ## _IRQ15 } }
-
-#define INTC_IRQ_PINS_MASK_16H(p, base) \
- { base + 0x48, base + 0x68, 8, /* INTMSK20A / INTMSKCLR20A */ \
- { p ## _IRQ16, p ## _IRQ17, p ## _IRQ18, p ## _IRQ19, \
- p ## _IRQ20, p ## _IRQ21, p ## _IRQ22, p ## _IRQ23 } }, \
- { base + 0x4c, base + 0x6c, 8, /* INTMSK30A / INTMSKCLR30A */ \
- { p ## _IRQ24, p ## _IRQ25, p ## _IRQ26, p ## _IRQ27, \
- p ## _IRQ28, p ## _IRQ29, p ## _IRQ30, p ## _IRQ31 } }
-
-#define INTC_IRQ_PINS_PRIO_16L(p, base) \
- { base + 0x10, 0, 32, 4, /* INTPRI00A */ \
- { p ## _IRQ0, p ## _IRQ1, p ## _IRQ2, p ## _IRQ3, \
- p ## _IRQ4, p ## _IRQ5, p ## _IRQ6, p ## _IRQ7 } }, \
- { base + 0x14, 0, 32, 4, /* INTPRI10A */ \
- { p ## _IRQ8, p ## _IRQ9, p ## _IRQ10, p ## _IRQ11, \
- p ## _IRQ12, p ## _IRQ13, p ## _IRQ14, p ## _IRQ15 } }
-
-#define INTC_IRQ_PINS_PRIO_16H(p, base) \
- { base + 0x18, 0, 32, 4, /* INTPRI20A */ \
- { p ## _IRQ16, p ## _IRQ17, p ## _IRQ18, p ## _IRQ19, \
- p ## _IRQ20, p ## _IRQ21, p ## _IRQ22, p ## _IRQ23 } }, \
- { base + 0x1c, 0, 32, 4, /* INTPRI30A */ \
- { p ## _IRQ24, p ## _IRQ25, p ## _IRQ26, p ## _IRQ27, \
- p ## _IRQ28, p ## _IRQ29, p ## _IRQ30, p ## _IRQ31 } }
-
-#define INTC_IRQ_PINS_SENSE_16L(p, base) \
- { base + 0x00, 32, 4, /* ICR1A */ \
- { p ## _IRQ0, p ## _IRQ1, p ## _IRQ2, p ## _IRQ3, \
- p ## _IRQ4, p ## _IRQ5, p ## _IRQ6, p ## _IRQ7 } }, \
- { base + 0x04, 32, 4, /* ICR2A */ \
- { p ## _IRQ8, p ## _IRQ9, p ## _IRQ10, p ## _IRQ11, \
- p ## _IRQ12, p ## _IRQ13, p ## _IRQ14, p ## _IRQ15 } }
-
-#define INTC_IRQ_PINS_SENSE_16H(p, base) \
- { base + 0x08, 32, 4, /* ICR3A */ \
- { p ## _IRQ16, p ## _IRQ17, p ## _IRQ18, p ## _IRQ19, \
- p ## _IRQ20, p ## _IRQ21, p ## _IRQ22, p ## _IRQ23 } }, \
- { base + 0x0c, 32, 4, /* ICR4A */ \
- { p ## _IRQ24, p ## _IRQ25, p ## _IRQ26, p ## _IRQ27, \
- p ## _IRQ28, p ## _IRQ29, p ## _IRQ30, p ## _IRQ31 } }
-
-#define INTC_IRQ_PINS_ACK_16L(p, base) \
- { base + 0x20, 0, 8, /* INTREQ00A */ \
- { p ## _IRQ0, p ## _IRQ1, p ## _IRQ2, p ## _IRQ3, \
- p ## _IRQ4, p ## _IRQ5, p ## _IRQ6, p ## _IRQ7 } }, \
- { base + 0x24, 0, 8, /* INTREQ10A */ \
- { p ## _IRQ8, p ## _IRQ9, p ## _IRQ10, p ## _IRQ11, \
- p ## _IRQ12, p ## _IRQ13, p ## _IRQ14, p ## _IRQ15 } }
-
-#define INTC_IRQ_PINS_ACK_16H(p, base) \
- { base + 0x28, 0, 8, /* INTREQ20A */ \
- { p ## _IRQ16, p ## _IRQ17, p ## _IRQ18, p ## _IRQ19, \
- p ## _IRQ20, p ## _IRQ21, p ## _IRQ22, p ## _IRQ23 } }, \
- { base + 0x2c, 0, 8, /* INTREQ30A */ \
- { p ## _IRQ24, p ## _IRQ25, p ## _IRQ26, p ## _IRQ27, \
- p ## _IRQ28, p ## _IRQ29, p ## _IRQ30, p ## _IRQ31 } }
-
-#define INTC_IRQ_PINS_16(p, base, vect, str) \
- \
-static struct resource p ## _resources[] __initdata = { \
- [0] = { \
- .start = base, \
- .end = base + 0x64, \
- .flags = IORESOURCE_MEM, \
- }, \
-}; \
- \
-enum { \
- p ## _UNUSED = 0, \
- INTC_IRQ_PINS_ENUM_16L(p), \
-}; \
- \
-static struct intc_vect p ## _vectors[] __initdata = { \
- INTC_IRQ_PINS_VECT_16L(p, vect), \
-}; \
- \
-static struct intc_mask_reg p ## _mask_registers[] __initdata = { \
- INTC_IRQ_PINS_MASK_16L(p, base), \
-}; \
- \
-static struct intc_prio_reg p ## _prio_registers[] __initdata = { \
- INTC_IRQ_PINS_PRIO_16L(p, base), \
-}; \
- \
-static struct intc_sense_reg p ## _sense_registers[] __initdata = { \
- INTC_IRQ_PINS_SENSE_16L(p, base), \
-}; \
- \
-static struct intc_mask_reg p ## _ack_registers[] __initdata = { \
- INTC_IRQ_PINS_ACK_16L(p, base), \
-}; \
- \
-static struct intc_desc p ## _desc __initdata = { \
- .name = str, \
- .resource = p ## _resources, \
- .num_resources = ARRAY_SIZE(p ## _resources), \
- .hw = INTC_HW_DESC(p ## _vectors, NULL, \
- p ## _mask_registers, p ## _prio_registers, \
- p ## _sense_registers, p ## _ack_registers) \
-}
-
-#define INTC_IRQ_PINS_16H(p, base, vect, str) \
- \
-static struct resource p ## _resources[] __initdata = { \
- [0] = { \
- .start = base, \
- .end = base + 0x64, \
- .flags = IORESOURCE_MEM, \
- }, \
-}; \
- \
-enum { \
- p ## _UNUSED = 0, \
- INTC_IRQ_PINS_ENUM_16H(p), \
-}; \
- \
-static struct intc_vect p ## _vectors[] __initdata = { \
- INTC_IRQ_PINS_VECT_16H(p, vect), \
-}; \
- \
-static struct intc_mask_reg p ## _mask_registers[] __initdata = { \
- INTC_IRQ_PINS_MASK_16H(p, base), \
-}; \
- \
-static struct intc_prio_reg p ## _prio_registers[] __initdata = { \
- INTC_IRQ_PINS_PRIO_16H(p, base), \
-}; \
- \
-static struct intc_sense_reg p ## _sense_registers[] __initdata = { \
- INTC_IRQ_PINS_SENSE_16H(p, base), \
-}; \
- \
-static struct intc_mask_reg p ## _ack_registers[] __initdata = { \
- INTC_IRQ_PINS_ACK_16H(p, base), \
-}; \
- \
-static struct intc_desc p ## _desc __initdata = { \
- .name = str, \
- .resource = p ## _resources, \
- .num_resources = ARRAY_SIZE(p ## _resources), \
- .hw = INTC_HW_DESC(p ## _vectors, NULL, \
- p ## _mask_registers, p ## _prio_registers, \
- p ## _sense_registers, p ## _ack_registers) \
-}
-
-#define INTC_IRQ_PINS_32(p, base, vect, str) \
- \
-static struct resource p ## _resources[] __initdata = { \
- [0] = { \
- .start = base, \
- .end = base + 0x6c, \
- .flags = IORESOURCE_MEM, \
- }, \
-}; \
- \
-enum { \
- p ## _UNUSED = 0, \
- INTC_IRQ_PINS_ENUM_16L(p), \
- INTC_IRQ_PINS_ENUM_16H(p), \
-}; \
- \
-static struct intc_vect p ## _vectors[] __initdata = { \
- INTC_IRQ_PINS_VECT_16L(p, vect), \
- INTC_IRQ_PINS_VECT_16H(p, vect), \
-}; \
- \
-static struct intc_mask_reg p ## _mask_registers[] __initdata = { \
- INTC_IRQ_PINS_MASK_16L(p, base), \
- INTC_IRQ_PINS_MASK_16H(p, base), \
-}; \
- \
-static struct intc_prio_reg p ## _prio_registers[] __initdata = { \
- INTC_IRQ_PINS_PRIO_16L(p, base), \
- INTC_IRQ_PINS_PRIO_16H(p, base), \
-}; \
- \
-static struct intc_sense_reg p ## _sense_registers[] __initdata = { \
- INTC_IRQ_PINS_SENSE_16L(p, base), \
- INTC_IRQ_PINS_SENSE_16H(p, base), \
-}; \
- \
-static struct intc_mask_reg p ## _ack_registers[] __initdata = { \
- INTC_IRQ_PINS_ACK_16L(p, base), \
- INTC_IRQ_PINS_ACK_16H(p, base), \
-}; \
- \
-static struct intc_desc p ## _desc __initdata = { \
- .name = str, \
- .resource = p ## _resources, \
- .num_resources = ARRAY_SIZE(p ## _resources), \
- .hw = INTC_HW_DESC(p ## _vectors, NULL, \
- p ## _mask_registers, p ## _prio_registers, \
- p ## _sense_registers, p ## _ack_registers) \
-}
-
-#define INTC_PINT_E_EMPTY
-#define INTC_PINT_E_NONE 0, 0, 0, 0, 0, 0, 0, 0,
-#define INTC_PINT_E(p) \
- PINT ## p ## 0, PINT ## p ## 1, PINT ## p ## 2, PINT ## p ## 3, \
- PINT ## p ## 4, PINT ## p ## 5, PINT ## p ## 6, PINT ## p ## 7,
-
-#define INTC_PINT_V_NONE
-#define INTC_PINT_V(p, vect) \
- vect(PINT ## p ## 0, 0), vect(PINT ## p ## 1, 1), \
- vect(PINT ## p ## 2, 2), vect(PINT ## p ## 3, 3), \
- vect(PINT ## p ## 4, 4), vect(PINT ## p ## 5, 5), \
- vect(PINT ## p ## 6, 6), vect(PINT ## p ## 7, 7),
-
-#define INTC_PINT(p, mask_reg, sense_base, str, \
- enums_1, enums_2, enums_3, enums_4, \
- vect_1, vect_2, vect_3, vect_4, \
- mask_a, mask_b, mask_c, mask_d, \
- sense_a, sense_b, sense_c, sense_d) \
- \
-enum { \
- PINT ## p ## _UNUSED = 0, \
- enums_1 enums_2 enums_3 enums_4 \
-}; \
- \
-static struct intc_vect p ## _vectors[] __initdata = { \
- vect_1 vect_2 vect_3 vect_4 \
-}; \
- \
-static struct intc_mask_reg p ## _mask_registers[] __initdata = { \
- { mask_reg, 0, 32, /* PINTER */ \
- { mask_a mask_b mask_c mask_d } } \
-}; \
- \
-static struct intc_sense_reg p ## _sense_registers[] __initdata = { \
- { sense_base + 0x00, 16, 2, /* PINTCR */ \
- { sense_a } }, \
- { sense_base + 0x04, 16, 2, /* PINTCR */ \
- { sense_b } }, \
- { sense_base + 0x08, 16, 2, /* PINTCR */ \
- { sense_c } }, \
- { sense_base + 0x0c, 16, 2, /* PINTCR */ \
- { sense_d } }, \
-}; \
- \
-static struct intc_desc p ## _desc __initdata = { \
- .name = str, \
- .hw = INTC_HW_DESC(p ## _vectors, NULL, \
- p ## _mask_registers, NULL, \
- p ## _sense_registers, NULL), \
-}
-
-/* INTCS */
-#define INTCS_VECT_BASE 0x3400
-#define INTCS_VECT(n, vect) INTC_VECT((n), INTCS_VECT_BASE + (vect))
-#define intcs_evt2irq(evt) evt2irq(INTCS_VECT_BASE + (evt))
-
-#endif /* __ASM_MACH_INTC_H */
static void apmu_parse_cfg(void (*fn)(struct resource *res, int cpu, int bit),
struct rcar_apmu_config *apmu_config, int num)
{
- u32 id;
+ int id;
int k;
int bit, index;
bool is_allowed;
dsb();
}
-void shmobile_smp_apmu_cpu_shutdown(unsigned int cpu)
+static void shmobile_smp_apmu_cpu_shutdown(unsigned int cpu)
{
/* Select next sleep mode using the APMU */
* for more details.
*/
-#include <linux/pm.h>
-#include <linux/suspend.h>
-#include <linux/err.h>
-#include <linux/pm_clock.h>
-#include <linux/pm_domain.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/console.h>
-
#include <asm/io.h>
-#include "common.h"
#include "pm-rcar.h"
#include "r8a7779.h"
#define SYSCIER 0x0c
#define SYSCIMR 0x10
-struct r8a7779_pm_domain {
- struct generic_pm_domain genpd;
- struct rcar_sysc_ch ch;
-};
-
-static inline
-const struct rcar_sysc_ch *to_r8a7779_ch(struct generic_pm_domain *d)
-{
- return &container_of(d, struct r8a7779_pm_domain, genpd)->ch;
-}
-
#if defined(CONFIG_PM) || defined(CONFIG_SMP)
static void __init r8a7779_sysc_init(void)
#endif /* CONFIG_PM || CONFIG_SMP */
-#ifdef CONFIG_PM
-
-static int pd_power_down(struct generic_pm_domain *genpd)
-{
- return rcar_sysc_power_down(to_r8a7779_ch(genpd));
-}
-
-static int pd_power_up(struct generic_pm_domain *genpd)
-{
- return rcar_sysc_power_up(to_r8a7779_ch(genpd));
-}
-
-static bool pd_is_off(struct generic_pm_domain *genpd)
-{
- return rcar_sysc_power_is_off(to_r8a7779_ch(genpd));
-}
-
-static bool pd_active_wakeup(struct device *dev)
-{
- return true;
-}
-
-static void r8a7779_init_pm_domain(struct r8a7779_pm_domain *r8a7779_pd)
-{
- struct generic_pm_domain *genpd = &r8a7779_pd->genpd;
-
- pm_genpd_init(genpd, NULL, false);
- genpd->dev_ops.active_wakeup = pd_active_wakeup;
- genpd->power_off = pd_power_down;
- genpd->power_on = pd_power_up;
-
- if (pd_is_off(&r8a7779_pd->genpd))
- pd_power_up(&r8a7779_pd->genpd);
-}
-
-static struct r8a7779_pm_domain r8a7779_pm_domains[] = {
- {
- .genpd.name = "SH4A",
- .ch = {
- .chan_offs = 0x80, /* PWRSR1 .. PWRER1 */
- .isr_bit = 16, /* SH4A */
- },
- },
- {
- .genpd.name = "SGX",
- .ch = {
- .chan_offs = 0xc0, /* PWRSR2 .. PWRER2 */
- .isr_bit = 20, /* SGX */
- },
- },
- {
- .genpd.name = "VDP1",
- .ch = {
- .chan_offs = 0x100, /* PWRSR3 .. PWRER3 */
- .isr_bit = 21, /* VDP */
- },
- },
- {
- .genpd.name = "IMPX3",
- .ch = {
- .chan_offs = 0x140, /* PWRSR4 .. PWRER4 */
- .isr_bit = 24, /* IMP */
- },
- },
-};
-
-void __init r8a7779_init_pm_domains(void)
-{
- int j;
-
- for (j = 0; j < ARRAY_SIZE(r8a7779_pm_domains); j++)
- r8a7779_init_pm_domain(&r8a7779_pm_domains[j]);
-}
-
-#endif /* CONFIG_PM */
-
void __init r8a7779_pm_init(void)
{
static int once;
}
pd = kzalloc(sizeof(*pd), GFP_KERNEL);
- if (!pd)
+ if (!pd) {
+ of_node_put(np);
return -ENOMEM;
+ }
pd->genpd.name = np->name;
pd->base = base;
#include <linux/pm_domain.h>
-#define DEFAULT_DEV_LATENCY_NS 250000
-
-struct platform_device;
-
struct rmobile_pm_domain {
struct generic_pm_domain genpd;
struct dev_power_governor *gov;
bool no_debug;
};
-struct pm_domain_device {
- const char *domain_name;
- struct platform_device *pdev;
-};
-
#endif /* PM_RMOBILE_H */
+++ /dev/null
-/*
- * Copyright (C) 2013 Renesas Solutions Corp.
- * Copyright (C) 2013 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- * Copyright (C) 2013 Cogent Embedded, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#ifndef __ASM_R8A7778_H__
-#define __ASM_R8A7778_H__
-
-#include <linux/sh_eth.h>
-
-/* HPB-DMA slave IDs */
-enum {
- HPBDMA_SLAVE_DUMMY,
- HPBDMA_SLAVE_SDHI0_TX,
- HPBDMA_SLAVE_SDHI0_RX,
- HPBDMA_SLAVE_SSI0_TX,
- HPBDMA_SLAVE_SSI0_RX,
- HPBDMA_SLAVE_SSI1_TX,
- HPBDMA_SLAVE_SSI1_RX,
- HPBDMA_SLAVE_SSI2_TX,
- HPBDMA_SLAVE_SSI2_RX,
- HPBDMA_SLAVE_SSI3_TX,
- HPBDMA_SLAVE_SSI3_RX,
- HPBDMA_SLAVE_SSI4_TX,
- HPBDMA_SLAVE_SSI4_RX,
- HPBDMA_SLAVE_SSI5_TX,
- HPBDMA_SLAVE_SSI5_RX,
- HPBDMA_SLAVE_SSI6_TX,
- HPBDMA_SLAVE_SSI6_RX,
- HPBDMA_SLAVE_SSI7_TX,
- HPBDMA_SLAVE_SSI7_RX,
- HPBDMA_SLAVE_SSI8_TX,
- HPBDMA_SLAVE_SSI8_RX,
- HPBDMA_SLAVE_HPBIF0_TX,
- HPBDMA_SLAVE_HPBIF0_RX,
- HPBDMA_SLAVE_HPBIF1_TX,
- HPBDMA_SLAVE_HPBIF1_RX,
- HPBDMA_SLAVE_HPBIF2_TX,
- HPBDMA_SLAVE_HPBIF2_RX,
- HPBDMA_SLAVE_HPBIF3_TX,
- HPBDMA_SLAVE_HPBIF3_RX,
- HPBDMA_SLAVE_HPBIF4_TX,
- HPBDMA_SLAVE_HPBIF4_RX,
- HPBDMA_SLAVE_HPBIF5_TX,
- HPBDMA_SLAVE_HPBIF5_RX,
- HPBDMA_SLAVE_HPBIF6_TX,
- HPBDMA_SLAVE_HPBIF6_RX,
- HPBDMA_SLAVE_HPBIF7_TX,
- HPBDMA_SLAVE_HPBIF7_RX,
- HPBDMA_SLAVE_HPBIF8_TX,
- HPBDMA_SLAVE_HPBIF8_RX,
- HPBDMA_SLAVE_USBFUNC_TX,
- HPBDMA_SLAVE_USBFUNC_RX,
-};
-
-extern void r8a7778_add_standard_devices(void);
-extern void r8a7778_add_standard_devices_dt(void);
-extern void r8a7778_add_dt_devices(void);
-
-extern void r8a7778_init_late(void);
-extern void r8a7778_init_irq_dt(void);
-extern void r8a7778_clock_init(void);
-extern void r8a7778_init_irq_extpin(int irlm);
-extern void r8a7778_init_irq_extpin_dt(int irlm);
-extern void r8a7778_pinmux_init(void);
-
-extern int r8a7778_usb_phy_power(bool enable);
-
-#endif /* __ASM_R8A7778_H__ */
#ifndef __ASM_R8A7779_H__
#define __ASM_R8A7779_H__
-#include <linux/sh_clk.h>
-
extern void r8a7779_pm_init(void);
-#ifdef CONFIG_PM
-extern void __init r8a7779_init_pm_domains(void);
-#else
-static inline void r8a7779_init_pm_domains(void) {}
-#endif /* CONFIG_PM */
-
extern struct smp_operations r8a7779_smp_ops;
#endif /* __ASM_R8A7779_H__ */
*/
#include <linux/clk/shmobile.h>
-#include <linux/kernel.h>
#include <linux/io.h>
-#include <linux/irqchip/arm-gic.h>
-#include <linux/of.h>
-#include <linux/of_platform.h>
-#include <linux/platform_data/dma-rcar-hpbdma.h>
-#include <linux/platform_data/gpio-rcar.h>
-#include <linux/platform_data/irq-renesas-intc-irqpin.h>
-#include <linux/platform_device.h>
#include <linux/irqchip.h>
-#include <linux/serial_sci.h>
-#include <linux/sh_timer.h>
-#include <linux/pm_runtime.h>
-#include <linux/usb/phy.h>
-#include <linux/usb/hcd.h>
-#include <linux/usb/ehci_pdriver.h>
-#include <linux/usb/ohci_pdriver.h>
-#include <linux/dma-mapping.h>
#include <asm/mach/arch.h>
-#include <asm/hardware/cache-l2x0.h>
#include "common.h"
#include "irqs.h"
-#include "r8a7778.h"
#define MODEMR 0xffcc0020
-#ifdef CONFIG_COMMON_CLK
static void __init r8a7778_timer_init(void)
{
u32 mode;
iounmap(modemr);
r8a7778_clocks_init(mode);
}
-#endif
-/* SCIF */
-#define R8A7778_SCIF(index, baseaddr, irq) \
-static struct plat_sci_port scif##index##_platform_data = { \
- .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP, \
- .scscr = SCSCR_RE | SCSCR_TE | SCSCR_CKE1, \
- .type = PORT_SCIF, \
-}; \
- \
-static struct resource scif##index##_resources[] = { \
- DEFINE_RES_MEM(baseaddr, 0x100), \
- DEFINE_RES_IRQ(irq), \
-}
-
-R8A7778_SCIF(0, 0xffe40000, gic_iid(0x66));
-R8A7778_SCIF(1, 0xffe41000, gic_iid(0x67));
-R8A7778_SCIF(2, 0xffe42000, gic_iid(0x68));
-R8A7778_SCIF(3, 0xffe43000, gic_iid(0x69));
-R8A7778_SCIF(4, 0xffe44000, gic_iid(0x6a));
-R8A7778_SCIF(5, 0xffe45000, gic_iid(0x6b));
-
-#define r8a7778_register_scif(index) \
- platform_device_register_resndata(NULL, "sh-sci", index, \
- scif##index##_resources, \
- ARRAY_SIZE(scif##index##_resources), \
- &scif##index##_platform_data, \
- sizeof(scif##index##_platform_data))
-
-/* TMU */
-static struct sh_timer_config sh_tmu0_platform_data = {
- .channels_mask = 7,
-};
-
-static struct resource sh_tmu0_resources[] = {
- DEFINE_RES_MEM(0xffd80000, 0x30),
- DEFINE_RES_IRQ(gic_iid(0x40)),
- DEFINE_RES_IRQ(gic_iid(0x41)),
- DEFINE_RES_IRQ(gic_iid(0x42)),
-};
-
-#define r8a7778_register_tmu(idx) \
- platform_device_register_resndata( \
- NULL, "sh-tmu", idx, \
- sh_tmu##idx##_resources, \
- ARRAY_SIZE(sh_tmu##idx##_resources), \
- &sh_tmu##idx##_platform_data, \
- sizeof(sh_tmu##idx##_platform_data))
-
-int r8a7778_usb_phy_power(bool enable)
-{
- static struct usb_phy *phy = NULL;
- int ret = 0;
-
- if (!phy)
- phy = usb_get_phy(USB_PHY_TYPE_USB2);
-
- if (IS_ERR(phy)) {
- pr_err("kernel doesn't have usb phy driver\n");
- return PTR_ERR(phy);
- }
-
- if (enable)
- ret = usb_phy_init(phy);
- else
- usb_phy_shutdown(phy);
-
- return ret;
-}
-
-/* USB */
-static int usb_power_on(struct platform_device *pdev)
-{
- int ret = r8a7778_usb_phy_power(true);
-
- if (ret)
- return ret;
-
- pm_runtime_enable(&pdev->dev);
- pm_runtime_get_sync(&pdev->dev);
-
- return 0;
-}
-
-static void usb_power_off(struct platform_device *pdev)
-{
- if (r8a7778_usb_phy_power(false))
- return;
-
- pm_runtime_put_sync(&pdev->dev);
- pm_runtime_disable(&pdev->dev);
-}
-
-static int ehci_init_internal_buffer(struct usb_hcd *hcd)
-{
- /*
- * Below are recommended values from the datasheet;
- * see [USB :: Setting of EHCI Internal Buffer].
- */
- /* EHCI IP internal buffer setting */
- iowrite32(0x00ff0040, hcd->regs + 0x0094);
- /* EHCI IP internal buffer enable */
- iowrite32(0x00000001, hcd->regs + 0x009C);
-
- return 0;
-}
-
-static struct usb_ehci_pdata ehci_pdata __initdata = {
- .power_on = usb_power_on,
- .power_off = usb_power_off,
- .power_suspend = usb_power_off,
- .pre_setup = ehci_init_internal_buffer,
-};
-
-static struct resource ehci_resources[] __initdata = {
- DEFINE_RES_MEM(0xffe70000, 0x400),
- DEFINE_RES_IRQ(gic_iid(0x4c)),
-};
-
-static struct usb_ohci_pdata ohci_pdata __initdata = {
- .power_on = usb_power_on,
- .power_off = usb_power_off,
- .power_suspend = usb_power_off,
-};
-
-static struct resource ohci_resources[] __initdata = {
- DEFINE_RES_MEM(0xffe70400, 0x400),
- DEFINE_RES_IRQ(gic_iid(0x4c)),
-};
-
-#define USB_PLATFORM_INFO(hci) \
-static struct platform_device_info hci##_info __initdata = { \
- .name = #hci "-platform", \
- .id = -1, \
- .res = hci##_resources, \
- .num_res = ARRAY_SIZE(hci##_resources), \
- .data = &hci##_pdata, \
- .size_data = sizeof(hci##_pdata), \
- .dma_mask = DMA_BIT_MASK(32), \
-}
-
-USB_PLATFORM_INFO(ehci);
-USB_PLATFORM_INFO(ohci);
-
-/* PFC/GPIO */
-static struct resource pfc_resources[] __initdata = {
- DEFINE_RES_MEM(0xfffc0000, 0x118),
-};
-
-#define R8A7778_GPIO(idx) \
-static struct resource r8a7778_gpio##idx##_resources[] __initdata = { \
- DEFINE_RES_MEM(0xffc40000 + 0x1000 * (idx), 0x30), \
- DEFINE_RES_IRQ(gic_iid(0x87)), \
-}; \
- \
-static struct gpio_rcar_config r8a7778_gpio##idx##_platform_data __initdata = { \
- .gpio_base = 32 * (idx), \
- .irq_base = GPIO_IRQ_BASE(idx), \
- .number_of_pins = 32, \
- .pctl_name = "pfc-r8a7778", \
-}
-
-R8A7778_GPIO(0);
-R8A7778_GPIO(1);
-R8A7778_GPIO(2);
-R8A7778_GPIO(3);
-R8A7778_GPIO(4);
-
-#define r8a7778_register_gpio(idx) \
- platform_device_register_resndata( \
- NULL, "gpio_rcar", idx, \
- r8a7778_gpio##idx##_resources, \
- ARRAY_SIZE(r8a7778_gpio##idx##_resources), \
- &r8a7778_gpio##idx##_platform_data, \
- sizeof(r8a7778_gpio##idx##_platform_data))
-
-void __init r8a7778_pinmux_init(void)
-{
- platform_device_register_simple(
- "pfc-r8a7778", -1,
- pfc_resources,
- ARRAY_SIZE(pfc_resources));
-
- r8a7778_register_gpio(0);
- r8a7778_register_gpio(1);
- r8a7778_register_gpio(2);
- r8a7778_register_gpio(3);
- r8a7778_register_gpio(4);
-};
-
-/* I2C */
-static struct resource i2c_resources[] __initdata = {
- /* I2C0 */
- DEFINE_RES_MEM(0xffc70000, 0x1000),
- DEFINE_RES_IRQ(gic_iid(0x63)),
- /* I2C1 */
- DEFINE_RES_MEM(0xffc71000, 0x1000),
- DEFINE_RES_IRQ(gic_iid(0x6e)),
- /* I2C2 */
- DEFINE_RES_MEM(0xffc72000, 0x1000),
- DEFINE_RES_IRQ(gic_iid(0x6c)),
- /* I2C3 */
- DEFINE_RES_MEM(0xffc73000, 0x1000),
- DEFINE_RES_IRQ(gic_iid(0x6d)),
-};
-
-static void __init r8a7778_register_i2c(int id)
-{
- BUG_ON(id < 0 || id > 3);
-
- platform_device_register_simple(
- "i2c-rcar", id,
- i2c_resources + (2 * id), 2);
-}
-
-/* HSPI */
-static struct resource hspi_resources[] __initdata = {
- /* HSPI0 */
- DEFINE_RES_MEM(0xfffc7000, 0x18),
- DEFINE_RES_IRQ(gic_iid(0x5f)),
- /* HSPI1 */
- DEFINE_RES_MEM(0xfffc8000, 0x18),
- DEFINE_RES_IRQ(gic_iid(0x74)),
- /* HSPI2 */
- DEFINE_RES_MEM(0xfffc6000, 0x18),
- DEFINE_RES_IRQ(gic_iid(0x75)),
-};
-
-static void __init r8a7778_register_hspi(int id)
-{
- BUG_ON(id < 0 || id > 2);
-
- platform_device_register_simple(
- "sh-hspi", id,
- hspi_resources + (2 * id), 2);
-}
-
-void __init r8a7778_add_dt_devices(void)
-{
-#ifdef CONFIG_CACHE_L2X0
- void __iomem *base = ioremap_nocache(0xf0100000, 0x1000);
- if (base) {
- /*
- * Shared attribute override enable, 64K*16way
- * don't call iounmap(base)
- */
- l2x0_init(base, 0x00400000, 0xc20f0fff);
- }
-#endif
-}
-
-/* HPB-DMA */
-
-/* Asynchronous mode register (ASYNCMDR) bits */
-#define HPB_DMAE_ASYNCMDR_ASMD22_MASK BIT(2) /* SDHI0 */
-#define HPB_DMAE_ASYNCMDR_ASMD22_SINGLE BIT(2) /* SDHI0 */
-#define HPB_DMAE_ASYNCMDR_ASMD22_MULTI 0 /* SDHI0 */
-#define HPB_DMAE_ASYNCMDR_ASMD21_MASK BIT(1) /* SDHI0 */
-#define HPB_DMAE_ASYNCMDR_ASMD21_SINGLE BIT(1) /* SDHI0 */
-#define HPB_DMAE_ASYNCMDR_ASMD21_MULTI 0 /* SDHI0 */
-
-#define HPBDMA_SSI(_id) \
-{ \
- .id = HPBDMA_SLAVE_SSI## _id ##_TX, \
- .addr = 0xffd91008 + (_id * 0x40), \
- .dcr = HPB_DMAE_DCR_CT | \
- HPB_DMAE_DCR_DIP | \
- HPB_DMAE_DCR_SPDS_32BIT | \
- HPB_DMAE_DCR_DMDL | \
- HPB_DMAE_DCR_DPDS_32BIT, \
- .port = _id + (_id << 8), \
- .dma_ch = (28 + _id), \
-}, { \
- .id = HPBDMA_SLAVE_SSI## _id ##_RX, \
- .addr = 0xffd9100c + (_id * 0x40), \
- .dcr = HPB_DMAE_DCR_CT | \
- HPB_DMAE_DCR_DIP | \
- HPB_DMAE_DCR_SMDL | \
- HPB_DMAE_DCR_SPDS_32BIT | \
- HPB_DMAE_DCR_DPDS_32BIT, \
- .port = _id + (_id << 8), \
- .dma_ch = (28 + _id), \
-}
-
-#define HPBDMA_HPBIF(_id) \
-{ \
- .id = HPBDMA_SLAVE_HPBIF## _id ##_TX, \
- .addr = 0xffda0000 + (_id * 0x1000), \
- .dcr = HPB_DMAE_DCR_CT | \
- HPB_DMAE_DCR_DIP | \
- HPB_DMAE_DCR_SPDS_32BIT | \
- HPB_DMAE_DCR_DMDL | \
- HPB_DMAE_DCR_DPDS_32BIT, \
- .port = 0x1111, \
- .dma_ch = (28 + _id), \
-}, { \
- .id = HPBDMA_SLAVE_HPBIF## _id ##_RX, \
- .addr = 0xffda0000 + (_id * 0x1000), \
- .dcr = HPB_DMAE_DCR_CT | \
- HPB_DMAE_DCR_DIP | \
- HPB_DMAE_DCR_SMDL | \
- HPB_DMAE_DCR_SPDS_32BIT | \
- HPB_DMAE_DCR_DPDS_32BIT, \
- .port = 0x1111, \
- .dma_ch = (28 + _id), \
-}
-
-static const struct hpb_dmae_slave_config hpb_dmae_slaves[] = {
- {
- .id = HPBDMA_SLAVE_SDHI0_TX,
- .addr = 0xffe4c000 + 0x30,
- .dcr = HPB_DMAE_DCR_SPDS_16BIT |
- HPB_DMAE_DCR_DMDL |
- HPB_DMAE_DCR_DPDS_16BIT,
- .rstr = HPB_DMAE_ASYNCRSTR_ASRST21 |
- HPB_DMAE_ASYNCRSTR_ASRST22 |
- HPB_DMAE_ASYNCRSTR_ASRST23,
- .mdr = HPB_DMAE_ASYNCMDR_ASMD21_MULTI,
- .mdm = HPB_DMAE_ASYNCMDR_ASMD21_MASK,
- .port = 0x0D0C,
- .flags = HPB_DMAE_SET_ASYNC_RESET | HPB_DMAE_SET_ASYNC_MODE,
- .dma_ch = 21,
- }, {
- .id = HPBDMA_SLAVE_SDHI0_RX,
- .addr = 0xffe4c000 + 0x30,
- .dcr = HPB_DMAE_DCR_SMDL |
- HPB_DMAE_DCR_SPDS_16BIT |
- HPB_DMAE_DCR_DPDS_16BIT,
- .rstr = HPB_DMAE_ASYNCRSTR_ASRST21 |
- HPB_DMAE_ASYNCRSTR_ASRST22 |
- HPB_DMAE_ASYNCRSTR_ASRST23,
- .mdr = HPB_DMAE_ASYNCMDR_ASMD22_MULTI,
- .mdm = HPB_DMAE_ASYNCMDR_ASMD22_MASK,
- .port = 0x0D0C,
- .flags = HPB_DMAE_SET_ASYNC_RESET | HPB_DMAE_SET_ASYNC_MODE,
- .dma_ch = 22,
- }, {
- .id = HPBDMA_SLAVE_USBFUNC_TX, /* for D0 */
- .addr = 0xffe60018,
- .dcr = HPB_DMAE_DCR_SPDS_32BIT |
- HPB_DMAE_DCR_DMDL |
- HPB_DMAE_DCR_DPDS_32BIT,
- .port = 0x0000,
- .dma_ch = 14,
- }, {
- .id = HPBDMA_SLAVE_USBFUNC_RX, /* for D1 */
- .addr = 0xffe6001c,
- .dcr = HPB_DMAE_DCR_SMDL |
- HPB_DMAE_DCR_SPDS_32BIT |
- HPB_DMAE_DCR_DPDS_32BIT,
- .port = 0x0101,
- .dma_ch = 15,
- },
-
- HPBDMA_SSI(0),
- HPBDMA_SSI(1),
- HPBDMA_SSI(2),
- HPBDMA_SSI(3),
- HPBDMA_SSI(4),
- HPBDMA_SSI(5),
- HPBDMA_SSI(6),
- HPBDMA_SSI(7),
- HPBDMA_SSI(8),
-
- HPBDMA_HPBIF(0),
- HPBDMA_HPBIF(1),
- HPBDMA_HPBIF(2),
- HPBDMA_HPBIF(3),
- HPBDMA_HPBIF(4),
- HPBDMA_HPBIF(5),
- HPBDMA_HPBIF(6),
- HPBDMA_HPBIF(7),
- HPBDMA_HPBIF(8),
-};
-
-static const struct hpb_dmae_channel hpb_dmae_channels[] = {
- HPB_DMAE_CHANNEL(0x7c, HPBDMA_SLAVE_USBFUNC_TX), /* ch. 14 */
- HPB_DMAE_CHANNEL(0x7c, HPBDMA_SLAVE_USBFUNC_RX), /* ch. 15 */
- HPB_DMAE_CHANNEL(0x7e, HPBDMA_SLAVE_SDHI0_TX), /* ch. 21 */
- HPB_DMAE_CHANNEL(0x7e, HPBDMA_SLAVE_SDHI0_RX), /* ch. 22 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI0_TX), /* ch. 28 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI0_RX), /* ch. 28 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF0_TX), /* ch. 28 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF0_RX), /* ch. 28 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI1_TX), /* ch. 29 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI1_RX), /* ch. 29 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF1_TX), /* ch. 29 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF1_RX), /* ch. 29 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI2_TX), /* ch. 30 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI2_RX), /* ch. 30 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF2_TX), /* ch. 30 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF2_RX), /* ch. 30 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI3_TX), /* ch. 31 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI3_RX), /* ch. 31 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF3_TX), /* ch. 31 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF3_RX), /* ch. 31 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI4_TX), /* ch. 32 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI4_RX), /* ch. 32 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF4_TX), /* ch. 32 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF4_RX), /* ch. 32 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI5_TX), /* ch. 33 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI5_RX), /* ch. 33 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF5_TX), /* ch. 33 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF5_RX), /* ch. 33 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI6_TX), /* ch. 34 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI6_RX), /* ch. 34 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF6_TX), /* ch. 34 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF6_RX), /* ch. 34 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI7_TX), /* ch. 35 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI7_RX), /* ch. 35 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF7_TX), /* ch. 35 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF7_RX), /* ch. 35 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI8_TX), /* ch. 36 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_SSI8_RX), /* ch. 36 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF8_TX), /* ch. 36 */
- HPB_DMAE_CHANNEL(0x7f, HPBDMA_SLAVE_HPBIF8_RX), /* ch. 36 */
-};
-
-static struct hpb_dmae_pdata dma_platform_data __initdata = {
- .slaves = hpb_dmae_slaves,
- .num_slaves = ARRAY_SIZE(hpb_dmae_slaves),
- .channels = hpb_dmae_channels,
- .num_channels = ARRAY_SIZE(hpb_dmae_channels),
- .ts_shift = {
- [XMIT_SZ_8BIT] = 0,
- [XMIT_SZ_16BIT] = 1,
- [XMIT_SZ_32BIT] = 2,
- },
- .num_hw_channels = 39,
-};
-
-static struct resource hpb_dmae_resources[] __initdata = {
- /* Channel registers */
- DEFINE_RES_MEM(0xffc08000, 0x1000),
- /* Common registers */
- DEFINE_RES_MEM(0xffc09000, 0x170),
- /* Asynchronous reset registers */
- DEFINE_RES_MEM(0xffc00300, 4),
- /* Asynchronous mode registers */
- DEFINE_RES_MEM(0xffc00400, 4),
- /* IRQ for DMA channels */
- DEFINE_RES_NAMED(gic_iid(0x7b), 5, NULL, IORESOURCE_IRQ),
-};
-
-static void __init r8a7778_register_hpb_dmae(void)
-{
- platform_device_register_resndata(NULL, "hpb-dma-engine",
- -1, hpb_dmae_resources,
- ARRAY_SIZE(hpb_dmae_resources),
- &dma_platform_data,
- sizeof(dma_platform_data));
-}
-
-void __init r8a7778_add_standard_devices(void)
-{
- r8a7778_add_dt_devices();
- r8a7778_register_tmu(0);
- r8a7778_register_scif(0);
- r8a7778_register_scif(1);
- r8a7778_register_scif(2);
- r8a7778_register_scif(3);
- r8a7778_register_scif(4);
- r8a7778_register_scif(5);
- r8a7778_register_i2c(0);
- r8a7778_register_i2c(1);
- r8a7778_register_i2c(2);
- r8a7778_register_i2c(3);
- r8a7778_register_hspi(0);
- r8a7778_register_hspi(1);
- r8a7778_register_hspi(2);
-
- r8a7778_register_hpb_dmae();
-}
-
-void __init r8a7778_init_late(void)
-{
- shmobile_init_late();
- platform_device_register_full(&ehci_info);
- platform_device_register_full(&ohci_info);
-}
-
-static struct renesas_intc_irqpin_config irqpin_platform_data __initdata = {
- .irq_base = irq_pin(0), /* IRQ0 -> IRQ3 */
- .sense_bitfield_width = 2,
-};
-
-static struct resource irqpin_resources[] __initdata = {
- DEFINE_RES_MEM(0xfe78001c, 4), /* ICR1 */
- DEFINE_RES_MEM(0xfe780010, 4), /* INTPRI */
- DEFINE_RES_MEM(0xfe780024, 4), /* INTREQ */
- DEFINE_RES_MEM(0xfe780044, 4), /* INTMSK0 */
- DEFINE_RES_MEM(0xfe780064, 4), /* INTMSKCLR0 */
- DEFINE_RES_IRQ(gic_iid(0x3b)), /* IRQ0 */
- DEFINE_RES_IRQ(gic_iid(0x3c)), /* IRQ1 */
- DEFINE_RES_IRQ(gic_iid(0x3d)), /* IRQ2 */
- DEFINE_RES_IRQ(gic_iid(0x3e)), /* IRQ3 */
-};
-
-void __init r8a7778_init_irq_extpin_dt(int irlm)
-{
- void __iomem *icr0 = ioremap_nocache(0xfe780000, PAGE_SIZE);
- unsigned long tmp;
-
- if (!icr0) {
- pr_warn("r8a7778: unable to setup external irq pin mode\n");
- return;
- }
-
- tmp = ioread32(icr0);
- if (irlm)
- tmp |= 1 << 23; /* IRQ0 -> IRQ3 as individual pins */
- else
- tmp &= ~(1 << 23); /* IRL mode - not supported */
- tmp |= (1 << 21); /* LVLMODE = 1 */
- iowrite32(tmp, icr0);
- iounmap(icr0);
-}
-
-void __init r8a7778_init_irq_extpin(int irlm)
-{
- r8a7778_init_irq_extpin_dt(irlm);
- if (irlm)
- platform_device_register_resndata(
- NULL, "renesas_intc_irqpin", -1,
- irqpin_resources, ARRAY_SIZE(irqpin_resources),
- &irqpin_platform_data, sizeof(irqpin_platform_data));
-}
-
-#ifdef CONFIG_USE_OF
#define INT2SMSKCR0 0x82288 /* 0xfe782288 */
#define INT2SMSKCR1 0x8228c /* 0xfe78228c */
#define INT2NTSR0 0x00018 /* 0xfe700018 */
#define INT2NTSR1 0x0002c /* 0xfe70002c */
-void __init r8a7778_init_irq_dt(void)
+
+static void __init r8a7778_init_irq_dt(void)
{
void __iomem *base = ioremap_nocache(0xfe700000, 0x00100000);
-#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
- void __iomem *gic_dist_base = ioremap_nocache(0xfe438000, 0x1000);
- void __iomem *gic_cpu_base = ioremap_nocache(0xfe430000, 0x1000);
-#endif
BUG_ON(!base);
-#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
- gic_init(0, 29, gic_dist_base, gic_cpu_base);
-#else
irqchip_init();
-#endif
+
/* route all interrupts to ARM */
__raw_writel(0x73ffffff, base + INT2NTSR0);
__raw_writel(0xffffffff, base + INT2NTSR1);
.init_early = shmobile_init_delay,
.init_irq = r8a7778_init_irq_dt,
.init_late = shmobile_init_late,
-#ifdef CONFIG_COMMON_CLK
.init_time = r8a7778_timer_init,
-#endif
.dt_compat = r8a7778_compat_dt,
MACHINE_END
-
-#endif /* CONFIG_USE_OF */
+++ /dev/null
-/*
- * Generic GPIO API and pinmux table support
- *
- * Copyright (c) 2008 Magnus Damm
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/io.h>
-
-/*
- * FIXME !!
- *
- * current gpio frame work doesn't have
- * the method to control only pull up/down/free.
- * this function should be replaced by correct gpio function
- */
-static inline void __init gpio_direction_none(void __iomem * addr)
-{
- __raw_writeb(0x00, addr);
-}
-
-#endif /* __ASM_ARCH_GPIO_H */
shmobile_setup_delay_hz(max_freq, 2, 4);
}
}
-
-static void __init shmobile_late_time_init(void)
-{
- /*
- * Make sure all compiled-in early timers register themselves.
- *
- * Run probe() for two "earlytimer" devices, these will be the
- * clockevents and clocksource devices respectively. In the event
- * that only a clockevents device is available, we -ENODEV on the
- * clocksource and the jiffies clocksource is used transparently
- * instead. No error handling is necessary here.
- */
- early_platform_driver_register_all("earlytimer");
- early_platform_driver_probe("earlytimer", 2, 0);
-}
-
-void __init shmobile_earlytimer_init(void)
-{
- late_time_init = shmobile_late_time_init;
-}
-
*
* Called with IRQs disabled
*/
-void __ref spear13xx_cpu_die(unsigned int cpu)
+void spear13xx_cpu_die(unsigned int cpu)
{
int spurious = 0;
*
* Called with IRQs disabled
*/
-void __ref tegra_cpu_die(unsigned int cpu)
+void tegra_cpu_die(unsigned int cpu)
{
if (!tegra_hotplug_shutdown) {
WARN(1, "hotplug is not yet initialized\n");
*
* Called with IRQs disabled
*/
-void __ref ux500_cpu_die(unsigned int cpu)
+void ux500_cpu_die(unsigned int cpu)
{
/* directly enter low power state, skipping secure registers */
for (;;) {
*
* Called with IRQs disabled
*/
-void __ref vexpress_cpu_die(unsigned int cpu)
+void vexpress_cpu_die(unsigned int cpu)
{
int spurious = 0;
bool
select CLKSRC_OF
+config CLKSRC_TI_32K
+ bool "Texas Instruments 32.768 Hz Clocksource" if COMPILE_TEST
+ depends on GENERIC_SCHED_CLOCK
+ select CLKSRC_OF if OF
+ help
+ This option enables support for Texas Instruments 32.768 Hz clocksource
+ available on many OMAP-like platforms.
+
config CLKSRC_STM32
bool "Clocksource for STM32 SoCs" if !ARCH_STM32
depends on OF && ARM && (ARCH_STM32 || COMPILE_TEST)
obj-$(CONFIG_CLKSRC_QCOM) += qcom-timer.o
obj-$(CONFIG_MTK_TIMER) += mtk_timer.o
obj-$(CONFIG_CLKSRC_PISTACHIO) += time-pistachio.o
+obj-$(CONFIG_CLKSRC_TI_32K) += timer-ti-32k.o
obj-$(CONFIG_ARM_ARCH_TIMER) += arm_arch_timer.o
obj-$(CONFIG_ARM_GLOBAL_TIMER) += arm_global_timer.o
--- /dev/null
+/**
+ * timer-ti-32k.c - OMAP2 32k Timer Support
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ *
+ * Update to use new clocksource/clockevent layers
+ * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *
+ * Original driver:
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Paul Mundt <paul.mundt@nokia.com>
+ * Juha Yrjölä <juha.yrjola@nokia.com>
+ * OMAP Dual-mode timer framework support by Timo Teras
+ *
+ * Some parts based off of TI's 24xx code:
+ *
+ * Copyright (C) 2004-2009 Texas Instruments, Inc.
+ *
+ * Roughly modelled after the OMAP1 MPU timer code.
+ * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/sched_clock.h>
+#include <linux/clocksource.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+
+/*
+ * 32KHz clocksource ... always available, on pretty most chips except
+ * OMAP 730 and 1510. Other timers could be used as clocksources, with
+ * higher resolution in free-running counter modes (e.g. 12 MHz xtal),
+ * but systems won't necessarily want to spend resources that way.
+ */
+
+#define OMAP2_32KSYNCNT_REV_OFF 0x0
+#define OMAP2_32KSYNCNT_REV_SCHEME (0x3 << 30)
+#define OMAP2_32KSYNCNT_CR_OFF_LOW 0x10
+#define OMAP2_32KSYNCNT_CR_OFF_HIGH 0x30
+
+struct ti_32k {
+ void __iomem *base;
+ void __iomem *counter;
+ struct clocksource cs;
+};
+
+static inline struct ti_32k *to_ti_32k(struct clocksource *cs)
+{
+ return container_of(cs, struct ti_32k, cs);
+}
+
+static cycle_t ti_32k_read_cycles(struct clocksource *cs)
+{
+ struct ti_32k *ti = to_ti_32k(cs);
+
+ return (cycle_t)readl_relaxed(ti->counter);
+}
+
+static struct ti_32k ti_32k_timer = {
+ .cs = {
+ .name = "32k_counter",
+ .rating = 250,
+ .read = ti_32k_read_cycles,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS |
+ CLOCK_SOURCE_SUSPEND_NONSTOP,
+ },
+};
+
+static u64 notrace omap_32k_read_sched_clock(void)
+{
+ return ti_32k_read_cycles(&ti_32k_timer.cs);
+}
+
+static void __init ti_32k_timer_init(struct device_node *np)
+{
+ int ret;
+
+ ti_32k_timer.base = of_iomap(np, 0);
+ if (!ti_32k_timer.base) {
+ pr_err("Can't ioremap 32k timer base\n");
+ return;
+ }
+
+ ti_32k_timer.counter = ti_32k_timer.base;
+
+ /*
+ * 32k sync Counter IP register offsets vary between the highlander
+ * version and the legacy ones.
+ *
+ * The 'SCHEME' bits(30-31) of the revision register is used to identify
+ * the version.
+ */
+ if (readl_relaxed(ti_32k_timer.base + OMAP2_32KSYNCNT_REV_OFF) &
+ OMAP2_32KSYNCNT_REV_SCHEME)
+ ti_32k_timer.counter += OMAP2_32KSYNCNT_CR_OFF_HIGH;
+ else
+ ti_32k_timer.counter += OMAP2_32KSYNCNT_CR_OFF_LOW;
+
+ ret = clocksource_register_hz(&ti_32k_timer.cs, 32768);
+ if (ret) {
+ pr_err("32k_counter: can't register clocksource\n");
+ return;
+ }
+
+ sched_clock_register(omap_32k_read_sched_clock, 32, 32768);
+ pr_info("OMAP clocksource: 32k_counter at 32768 Hz\n");
+}
+CLOCKSOURCE_OF_DECLARE(ti_32k_timer, "ti,omap-counter32k",
+ ti_32k_timer_init);
/* device.platform_data for SSP controller devices */
struct pxa2xx_spi_master {
- u32 clock_enable;
u16 num_chipselect;
u8 enable_dma;
projects / firefly-linux-kernel-4.4.55.git / commitdiff