- compatible: Should be "cdns,[<chip>-]{macb|gem}"
Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
- Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+ Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
the Cadence GEM, or the generic form: "cdns,gem".
- reg: Address and length of the register set for the device
- interrupts: Should contain macb interrupt
--- /dev/null
+Simple Framebuffer
+
+A simple frame-buffer describes a raw memory region that may be rendered to,
+with the assumption that the display hardware has already been set up to scan
+out from that buffer.
+
+Required properties:
+- compatible: "simple-framebuffer"
+- reg: Should contain the location and size of the framebuffer memory.
+- width: The width of the framebuffer in pixels.
+- height: The height of the framebuffer in pixels.
+- stride: The number of bytes in each line of the framebuffer.
+- format: The format of the framebuffer surface. Valid values are:
+ - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
+
+Example:
+
+ framebuffer {
+ compatible = "simple-framebuffer";
+ reg = <0x1d385000 (1600 * 1200 * 2)>;
+ width = <1600>;
+ height = <1200>;
+ stride = <(1600 * 2)>;
+ format = "r5g6b5";
+ };
In order to initialize the RapidIO subsystem, a platform must initialize and
register at least one master port within the RapidIO network. To register mport
within the subsystem controller driver initialization code calls function
-rio_register_mport() for each available master port. After all active master
-ports are registered with a RapidIO subsystem, the rio_init_mports() routine
-is called to perform enumeration and discovery.
+rio_register_mport() for each available master port.
-In the current PowerPC-based implementation a subsys_initcall() is specified to
-perform controller initialization and mport registration. At the end it directly
-calls rio_init_mports() to execute RapidIO enumeration and discovery.
+RapidIO subsystem uses subsys_initcall() or device_initcall() to perform
+controller initialization (depending on controller device type).
+
+After all active master ports are registered with a RapidIO subsystem,
+an enumeration and/or discovery routine may be called automatically or
+by user-space command.
4. Enumeration and Discovery
----------------------------
-When rio_init_mports() is called it scans a list of registered master ports and
-calls an enumeration or discovery routine depending on the configured role of a
-master port: host or agent.
+4.1 Overview
+------------
+
+RapidIO subsystem configuration options allow users to specify enumeration and
+discovery methods as statically linked components or loadable modules.
+An enumeration/discovery method implementation and available input parameters
+define how any given method can be attached to available RapidIO mports:
+simply to all available mports OR individually to the specified mport device.
+
+Depending on selected enumeration/discovery build configuration, there are
+several methods to initiate an enumeration and/or discovery process:
+
+ (a) Statically linked enumeration and discovery process can be started
+ automatically during kernel initialization time using corresponding module
+ parameters. This was the original method used since introduction of RapidIO
+ subsystem. Now this method relies on enumerator module parameter which is
+ 'rio-scan.scan' for existing basic enumeration/discovery method.
+ When automatic start of enumeration/discovery is used a user has to ensure
+ that all discovering endpoints are started before the enumerating endpoint
+ and are waiting for enumeration to be completed.
+ Configuration option CONFIG_RAPIDIO_DISC_TIMEOUT defines time that discovering
+ endpoint waits for enumeration to be completed. If the specified timeout
+ expires the discovery process is terminated without obtaining RapidIO network
+ information. NOTE: a timed out discovery process may be restarted later using
+ a user-space command as it is described later if the given endpoint was
+ enumerated successfully.
+
+ (b) Statically linked enumeration and discovery process can be started by
+ a command from user space. This initiation method provides more flexibility
+ for a system startup compared to the option (a) above. After all participating
+ endpoints have been successfully booted, an enumeration process shall be
+ started first by issuing a user-space command, after an enumeration is
+ completed a discovery process can be started on all remaining endpoints.
+
+ (c) Modular enumeration and discovery process can be started by a command from
+ user space. After an enumeration/discovery module is loaded, a network scan
+ process can be started by issuing a user-space command.
+ Similar to the option (b) above, an enumerator has to be started first.
+
+ (d) Modular enumeration and discovery process can be started by a module
+ initialization routine. In this case an enumerating module shall be loaded
+ first.
+
+When a network scan process is started it calls an enumeration or discovery
+routine depending on the configured role of a master port: host or agent.
Enumeration is performed by a master port if it is configured as a host port by
assigning a host device ID greater than or equal to zero. A host device ID is
The enumeration and discovery routines use RapidIO maintenance transactions
to access the configuration space of devices.
-The enumeration process is implemented according to the enumeration algorithm
-outlined in the RapidIO Interconnect Specification: Annex I [1].
+4.2 Automatic Start of Enumeration and Discovery
+------------------------------------------------
+
+Automatic enumeration/discovery start method is applicable only to built-in
+enumeration/discovery RapidIO configuration selection. To enable automatic
+enumeration/discovery start by existing basic enumerator method set use boot
+command line parameter "rio-scan.scan=1".
+
+This configuration requires synchronized start of all RapidIO endpoints that
+form a network which will be enumerated/discovered. Discovering endpoints have
+to be started before an enumeration starts to ensure that all RapidIO
+controllers have been initialized and are ready to be discovered. Configuration
+parameter CONFIG_RAPIDIO_DISC_TIMEOUT defines time (in seconds) which
+a discovering endpoint will wait for enumeration to be completed.
+
+When automatic enumeration/discovery start is selected, basic method's
+initialization routine calls rio_init_mports() to perform enumeration or
+discovery for all known mport devices.
+
+Depending on RapidIO network size and configuration this automatic
+enumeration/discovery start method may be difficult to use due to the
+requirement for synchronized start of all endpoints.
+
+4.3 User-space Start of Enumeration and Discovery
+-------------------------------------------------
+
+User-space start of enumeration and discovery can be used with built-in and
+modular build configurations. For user-space controlled start RapidIO subsystem
+creates the sysfs write-only attribute file '/sys/bus/rapidio/scan'. To initiate
+an enumeration or discovery process on specific mport device, a user needs to
+write mport_ID (not RapidIO destination ID) into that file. The mport_ID is a
+sequential number (0 ... RIO_MAX_MPORTS) assigned during mport device
+registration. For example for machine with single RapidIO controller, mport_ID
+for that controller always will be 0.
+
+To initiate RapidIO enumeration/discovery on all available mports a user may
+write '-1' (or RIO_MPORT_ANY) into the scan attribute file.
+
+4.4 Basic Enumeration Method
+----------------------------
+
+This is an original enumeration/discovery method which is available since
+first release of RapidIO subsystem code. The enumeration process is
+implemented according to the enumeration algorithm outlined in the RapidIO
+Interconnect Specification: Annex I [1].
+
+This method can be configured as statically linked or loadable module.
+The method's single parameter "scan" allows to trigger the enumeration/discovery
+process from module initialization routine.
+
+This enumeration/discovery method can be started only once and does not support
+unloading if it is built as a module.
The enumeration process traverses the network using a recursive depth-first
algorithm. When a new device is found, the enumerator takes ownership of that
an agent skips RapidIO discovery and continues with remaining kernel
initialization.
+4.5 Adding New Enumeration/Discovery Method
+-------------------------------------------
+
+RapidIO subsystem code organization allows addition of new enumeration/discovery
+methods as new configuration options without significant impact to to the core
+RapidIO code.
+
+A new enumeration/discovery method has to be attached to one or more mport
+devices before an enumeration/discovery process can be started. Normally,
+method's module initialization routine calls rio_register_scan() to attach
+an enumerator to a specified mport device (or devices). The basic enumerator
+implementation demonstrates this process.
+
5. References
-------------
IDT_GEN2:
errlog - reads contents of device error log until it is empty.
+
+
+5. RapidIO Bus Attributes
+-------------------------
+
+RapidIO bus subdirectory /sys/bus/rapidio implements the following bus-specific
+attribute:
+
+ scan - allows to trigger enumeration discovery process from user space. This
+ is a write-only attribute. To initiate an enumeration or discovery
+ process on specific mport device, a user needs to write mport_ID (not
+ RapidIO destination ID) into this file. The mport_ID is a sequential
+ number (0 ... RIO_MAX_MPORTS) assigned to the mport device.
+ For example, for a machine with a single RapidIO controller, mport_ID
+ for that controller always will be 0.
+ To initiate RapidIO enumeration/discovery on all available mports
+ a user must write '-1' (or RIO_MPORT_ANY) into this attribute file.
M: Haiyang Zhang <haiyangz@microsoft.com>
L: devel@linuxdriverproject.org
S: Maintained
-F: drivers/hv/
+F: arch/x86/include/asm/mshyperv.h
+F: arch/x86/include/uapi/asm/hyperv.h
+F: arch/x86/kernel/cpu/mshyperv.c
F: drivers/hid/hid-hyperv.c
+F: drivers/hv/
F: drivers/net/hyperv/
+F: drivers/scsi/storvsc_drv.c
+F: drivers/video/hyperv_fb.c
+F: include/linux/hyperv.h
+F: tools/hv/
I2C OVER PARALLEL PORT
M: Jean Delvare <khali@linux-fr.org>
F: include/uapi/linux/sunrpc/
KERNEL VIRTUAL MACHINE (KVM)
-M: Marcelo Tosatti <mtosatti@redhat.com>
M: Gleb Natapov <gleb@redhat.com>
+M: Paolo Bonzini <pbonzini@redhat.com>
L: kvm@vger.kernel.org
-W: http://kvm.qumranet.com
+W: http://linux-kvm.org
S: Supported
-F: Documentation/*/kvm.txt
+F: Documentation/*/kvm*.txt
+F: Documentation/virtual/kvm/
F: arch/*/kvm/
F: arch/*/include/asm/kvm*
F: include/linux/kvm*
F: Documentation/networking/vxge.txt
F: drivers/net/ethernet/neterion/
-NETFILTER/IPTABLES/IPCHAINS
-P: Harald Welte
-P: Jozsef Kadlecsik
+NETFILTER/IPTABLES
M: Pablo Neira Ayuso <pablo@netfilter.org>
M: Patrick McHardy <kaber@trash.net>
+M: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
L: netfilter-devel@vger.kernel.org
L: netfilter@vger.kernel.org
L: coreteam@netfilter.org
W: http://www.netfilter.org/
W: http://www.iptables.org/
-T: git git://1984.lsi.us.es/nf
-T: git git://1984.lsi.us.es/nf-next
+Q: http://patchwork.ozlabs.org/project/netfilter-devel/list/
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next.git
S: Supported
F: include/linux/netfilter*
F: include/linux/netfilter/
W: http://www.parisc-linux.org/
Q: http://patchwork.kernel.org/project/linux-parisc/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux.git
S: Maintained
F: arch/parisc/
F: drivers/parisc/
VERSION = 3
PATCHLEVEL = 10
SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
NAME = Unicycling Gorilla
# *DOCUMENTATION*
soc100 {
uart@FF100000 {
- pinctrl-names = "abilis,simple-default";
+ pinctrl-names = "default";
pinctrl-0 = <&pctl_uart0>;
};
ethernet@FE100000 {
soc100 {
uart@FF100000 {
- pinctrl-names = "abilis,simple-default";
+ pinctrl-names = "default";
pinctrl-0 = <&pctl_uart0>;
};
ethernet@FE100000 {
};
uart@FF100000 {
- compatible = "snps,dw-apb-uart",
- "abilis,simple-pinctrl";
+ compatible = "snps,dw-apb-uart";
reg = <0xFF100000 0x100>;
clock-frequency = <166666666>;
interrupts = <25 1>;
#address-cells = <1>;
#size-cells = <0>;
cell-index = <1>;
- compatible = "abilis,tb100-spi",
- "abilis,simple-pinctrl";
+ compatible = "abilis,tb100-spi";
num-cs = <2>;
reg = <0xFE011000 0x20>;
interrupt-parent = <&tb10x_ictl>;
#endif
}
-#define CACHE_COLOR(addr) (((unsigned long)(addr) >> (PAGE_SHIFT)) & 3)
+#define CACHE_COLOR(addr) (((unsigned long)(addr) >> (PAGE_SHIFT)) & 1)
/*
* checks if two addresses (after page aligning) index into same cache set
*/
#define addr_not_cache_congruent(addr1, addr2) \
+({ \
cache_is_vipt_aliasing() ? \
- (CACHE_COLOR(addr1) != CACHE_COLOR(addr2)) : 0 \
+ (CACHE_COLOR(addr1) != CACHE_COLOR(addr2)) : 0; \
+})
#define copy_to_user_page(vma, page, vaddr, dst, src, len) \
do { \
#define clear_page(paddr) memset((paddr), 0, PAGE_SIZE)
#define copy_page(to, from) memcpy((to), (from), PAGE_SIZE)
-#ifndef CONFIG_ARC_CACHE_VIPT_ALIASING
-
-#define clear_user_page(addr, vaddr, pg) clear_page(addr)
-#define copy_user_page(vto, vfrom, vaddr, pg) copy_page(vto, vfrom)
-
-#else /* VIPT aliasing dcache */
-
struct vm_area_struct;
struct page;
unsigned long u_vaddr, struct vm_area_struct *vma);
void clear_user_page(void *to, unsigned long u_vaddr, struct page *page);
-#endif /* CONFIG_ARC_CACHE_VIPT_ALIASING */
-
#undef STRICT_MM_TYPECHECKS
#ifdef STRICT_MM_TYPECHECKS
#define _PAGE_ACCESSED (1<<1) /* Page is accessed (S) */
#define _PAGE_CACHEABLE (1<<2) /* Page is cached (H) */
-#define _PAGE_EXECUTE (1<<3) /* Page has user execute perm (H) */
-#define _PAGE_WRITE (1<<4) /* Page has user write perm (H) */
-#define _PAGE_READ (1<<5) /* Page has user read perm (H) */
+#define _PAGE_U_EXECUTE (1<<3) /* Page has user execute perm (H) */
+#define _PAGE_U_WRITE (1<<4) /* Page has user write perm (H) */
+#define _PAGE_U_READ (1<<5) /* Page has user read perm (H) */
#define _PAGE_K_EXECUTE (1<<6) /* Page has kernel execute perm (H) */
#define _PAGE_K_WRITE (1<<7) /* Page has kernel write perm (H) */
#define _PAGE_K_READ (1<<8) /* Page has kernel perm (H) */
/* PD1 */
#define _PAGE_CACHEABLE (1<<0) /* Page is cached (H) */
-#define _PAGE_EXECUTE (1<<1) /* Page has user execute perm (H) */
-#define _PAGE_WRITE (1<<2) /* Page has user write perm (H) */
-#define _PAGE_READ (1<<3) /* Page has user read perm (H) */
+#define _PAGE_U_EXECUTE (1<<1) /* Page has user execute perm (H) */
+#define _PAGE_U_WRITE (1<<2) /* Page has user write perm (H) */
+#define _PAGE_U_READ (1<<3) /* Page has user read perm (H) */
#define _PAGE_K_EXECUTE (1<<4) /* Page has kernel execute perm (H) */
#define _PAGE_K_WRITE (1<<5) /* Page has kernel write perm (H) */
#define _PAGE_K_READ (1<<6) /* Page has kernel perm (H) */
#endif
/* Kernel allowed all permissions for all pages */
-#define _K_PAGE_PERMS (_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ)
+#define _K_PAGE_PERMS (_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ | \
+ _PAGE_GLOBAL | _PAGE_PRESENT)
#ifdef CONFIG_ARC_CACHE_PAGES
#define _PAGE_DEF_CACHEABLE _PAGE_CACHEABLE
* -by default cached, unless config otherwise
* -present in memory
*/
-#define ___DEF (_PAGE_PRESENT | _K_PAGE_PERMS | _PAGE_DEF_CACHEABLE)
+#define ___DEF (_PAGE_PRESENT | _PAGE_DEF_CACHEABLE)
+
+#define _PAGE_READ (_PAGE_U_READ | _PAGE_K_READ)
+#define _PAGE_WRITE (_PAGE_U_WRITE | _PAGE_K_WRITE)
+#define _PAGE_EXECUTE (_PAGE_U_EXECUTE | _PAGE_K_EXECUTE)
/* Set of bits not changed in pte_modify */
#define _PAGE_CHG_MASK (PAGE_MASK | _PAGE_ACCESSED | _PAGE_MODIFIED)
* kernel vaddr space - visible in all addr spaces, but kernel mode only
* Thus Global, all-kernel-access, no-user-access, cached
*/
-#define PAGE_KERNEL __pgprot(___DEF | _PAGE_GLOBAL)
+#define PAGE_KERNEL __pgprot(_K_PAGE_PERMS | _PAGE_DEF_CACHEABLE)
/* ioremap */
-#define PAGE_KERNEL_NO_CACHE __pgprot(_PAGE_PRESENT | _K_PAGE_PERMS | \
- _PAGE_GLOBAL)
+#define PAGE_KERNEL_NO_CACHE __pgprot(_K_PAGE_PERMS)
/**************************************************************************
* Mapping of vm_flags (Generic VM) to PTE flags (arch specific)
/* Masks for actual TLB "PD"s */
#define PTE_BITS_IN_PD0 (_PAGE_GLOBAL | _PAGE_PRESENT)
#define PTE_BITS_IN_PD1 (PAGE_MASK | _PAGE_CACHEABLE | \
- _PAGE_EXECUTE | _PAGE_WRITE | _PAGE_READ | \
+ _PAGE_U_EXECUTE | _PAGE_U_WRITE | _PAGE_U_READ | \
_PAGE_K_EXECUTE | _PAGE_K_WRITE | _PAGE_K_READ)
#ifndef __ASSEMBLY__
local_irq_save(flags);
__ic_line_inv_vaddr(paddr, vaddr, len);
- __dc_line_op(paddr, vaddr, len, OP_FLUSH);
+ __dc_line_op(paddr, vaddr, len, OP_FLUSH_N_INV);
local_irq_restore(flags);
}
flush_cache_all();
}
+void flush_anon_page(struct vm_area_struct *vma, struct page *page,
+ unsigned long u_vaddr)
+{
+ /* TBD: do we really need to clear the kernel mapping */
+ __flush_dcache_page(page_address(page), u_vaddr);
+ __flush_dcache_page(page_address(page), page_address(page));
+
+}
+
+#endif
+
void copy_user_highpage(struct page *to, struct page *from,
unsigned long u_vaddr, struct vm_area_struct *vma)
{
set_bit(PG_arch_1, &page->flags);
}
-void flush_anon_page(struct vm_area_struct *vma, struct page *page,
- unsigned long u_vaddr)
-{
- /* TBD: do we really need to clear the kernel mapping */
- __flush_dcache_page(page_address(page), u_vaddr);
- __flush_dcache_page(page_address(page), page_address(page));
-
-}
-
-#endif
/**********************************************************************
* Explicit Cache flush request from user space via syscall
* so userspace sees the right data.
* (Avoids the flush for Non-exec + congruent mapping case)
*/
- if (vma->vm_flags & VM_EXEC || addr_not_cache_congruent(paddr, vaddr)) {
+ if ((vma->vm_flags & VM_EXEC) ||
+ addr_not_cache_congruent(paddr, vaddr)) {
struct page *page = pfn_to_page(pte_pfn(*ptep));
int dirty = test_and_clear_bit(PG_arch_1, &page->flags);
;----------------------------------------------------------------
; VERIFY_PTE: Check if PTE permissions approp for executing code
cmp_s r2, VMALLOC_START
- mov.lo r2, (_PAGE_PRESENT | _PAGE_READ | _PAGE_EXECUTE)
+ mov.lo r2, (_PAGE_PRESENT | _PAGE_U_READ | _PAGE_U_EXECUTE)
mov.hs r2, (_PAGE_PRESENT | _PAGE_K_READ | _PAGE_K_EXECUTE)
and r3, r0, r2 ; Mask out NON Flag bits from PTE
mov_s r2, 0
lr r3, [ecr]
btst_s r3, ECR_C_BIT_DTLB_LD_MISS ; Read Access
- or.nz r2, r2, _PAGE_READ ; chk for Read flag in PTE
+ or.nz r2, r2, _PAGE_U_READ ; chk for Read flag in PTE
btst_s r3, ECR_C_BIT_DTLB_ST_MISS ; Write Access
- or.nz r2, r2, _PAGE_WRITE ; chk for Write flag in PTE
+ or.nz r2, r2, _PAGE_U_WRITE ; chk for Write flag in PTE
; Above laddering takes care of XCHG access
; which is both Read and Write
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
-static void __init tb10x_platform_late_init(void)
-{
- struct device_node *dn;
-
- /*
- * Pinctrl documentation recommends setting up the iomux here for
- * all modules which don't require control over the pins themselves.
- * Modules which need this kind of assistance are compatible with
- * "abilis,simple-pinctrl", i.e. we can easily iterate over them.
- * TODO: Does this recommended method work cleanly with pins required
- * by modules?
- */
- for_each_compatible_node(dn, NULL, "abilis,simple-pinctrl") {
- struct platform_device *pd = of_find_device_by_node(dn);
- struct pinctrl *pctl;
-
- pctl = pinctrl_get_select(&pd->dev, "abilis,simple-default");
- if (IS_ERR(pctl)) {
- int ret = PTR_ERR(pctl);
- dev_err(&pd->dev, "Could not set up pinctrl: %d\n",
- ret);
- }
- }
-}
-
static const char *tb10x_compat[] __initdata = {
"abilis,arc-tb10x",
NULL,
MACHINE_START(TB10x, "tb10x")
.dt_compat = tb10x_compat,
.init_machine = tb10x_platform_init,
- .init_late = tb10x_platform_late_init,
MACHINE_END
Enable hardware performance counter support for perf events. If
disabled, perf events will use software events only.
+config SYS_SUPPORTS_HUGETLBFS
+ def_bool y
+ depends on ARM_LPAE
+
+config HAVE_ARCH_TRANSPARENT_HUGEPAGE
+ def_bool y
+ depends on ARM_LPAE
+
source "mm/Kconfig"
config FORCE_MAX_ZONEORDER
spear320-evb.dtb \
spear320-hmi.dtb
dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
-dtb-$(CONFIG_ARCH_SUNXI) += sun4i-a10-cubieboard.dtb \
+dtb-$(CONFIG_ARCH_SUNXI) += \
+ sun4i-a10-cubieboard.dtb \
+ sun4i-a10-mini-xplus.dtb \
sun4i-a10-hackberry.dtb \
sun5i-a13-olinuxino.dtb
dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
#size-cells = <1>;
compatible = "simple-bus";
interrupt-parent = <&mpic>;
- ranges = <0 0 0xd0000000 0x100000>;
+ ranges = <0 0 0xd0000000 0x0100000 /* internal registers */
+ 0xe0000000 0 0xe0000000 0x8100000 /* PCIe */>;
internal-regs {
compatible = "simple-bus";
};
soc {
- ranges = <0 0xd0000000 0x100000>;
+ ranges = <0 0xd0000000 0x0100000 /* internal registers */
+ 0xe0000000 0xe0000000 0x8100000 /* PCIe */>;
internal-regs {
system-controller@18200 {
compatible = "marvell,armada-370-xp-system-controller";
L2: l2-cache {
compatible = "marvell,aurora-outer-cache";
- reg = <0xd0008000 0x1000>;
+ reg = <0x08000 0x1000>;
cache-id-part = <0x100>;
wt-override;
};
- mpic: interrupt-controller@20000 {
+ interrupt-controller@20000 {
reg = <0x20a00 0x1d0>, <0x21870 0x58>;
};
};
soc {
+ ranges = <0 0 0xd0000000 0x100000
+ 0xf0000000 0 0xf0000000 0x1000000>;
+
internal-regs {
serial@12000 {
clock-frequency = <250000000>;
};
soc {
+ ranges = <0 0 0xd0000000 0x100000
+ 0xf0000000 0 0xf0000000 0x8000000>;
+
internal-regs {
serial@12000 {
clock-frequency = <250000000>;
wt-override;
};
- mpic: interrupt-controller@20000 {
+ interrupt-controller@20000 {
reg = <0x20a00 0x2d0>, <0x21070 0x58>;
};
atmel,pins =
<0 10 0x2 0x0 /* PA10 periph B */
0 11 0x2 0x0 /* PA11 periph B */
- 0 24 0x2 0x0 /* PA24 periph B */
+ 0 22 0x2 0x0 /* PA22 periph B */
0 25 0x2 0x0 /* PA25 periph B */
0 26 0x2 0x0 /* PA26 periph B */
0 27 0x2 0x0 /* PA27 periph B */
compatible = "atmel,at91rm9200-aic";
interrupt-controller;
reg = <0xfffff000 0x200>;
+ atmel,external-irqs = <31>;
};
ramc0: ramc@ffffe800 {
/include/ "at91sam9x5ek.dtsi"
/ {
- model = "Atmel AT91SAM9G25-EK";
+ model = "Atmel AT91SAM9X25-EK";
compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
ahb {
usb_otg_hs: usb_otg_hs@480ab000 {
compatible = "ti,omap3-musb";
reg = <0x480ab000 0x1000>;
- interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupts = <92>, <93>;
interrupt-names = "mc", "dma";
ti,hwmods = "usb_otg_hs";
multipoint = <1>;
compatible = "atmel,at91sam9x5-spi";
reg = <0xf0004000 0x100>;
interrupts = <24 4 3>;
- cs-gpios = <&pioD 13 0
- &pioD 14 0 /* conflicts with SCK0 and CANRX0 */
- &pioD 15 0 /* conflicts with CTS0 and CANTX0 */
- &pioD 16 0 /* conflicts with RTS0 and PWMFI3 */
- >;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0>;
status = "disabled";
};
macb0: ethernet@f0028000 {
- compatible = "cnds,pc302-gem", "cdns,gem";
+ compatible = "cdns,pc302-gem", "cdns,gem";
reg = <0xf0028000 0x100>;
interrupts = <34 4 3>;
pinctrl-names = "default";
compatible = "atmel,at91sam9x5-spi";
reg = <0xf8008000 0x100>;
interrupts = <25 4 3>;
- cs-gpios = <&pioC 25 0
- &pioC 26 0 /* conflitcs with TWD1 and ISI_D11 */
- &pioC 27 0 /* conflitcs with TWCK1 and ISI_D10 */
- &pioC 28 0 /* conflitcs with PWMFI0 and ISI_D9 */
- >;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi1>;
status = "disabled";
ahb {
apb {
+ spi0: spi@f0004000 {
+ cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+ };
+
macb0: ethernet@f0028000 {
phy-mode = "rgmii";
};
bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
};
+ /* This is where the interrupt is routed on the S8815 board */
+ external-bus@34000000 {
+ ethernet@300 {
+ interrupt-parent = <&gpio3>;
+ interrupts = <8 0x1>;
+ };
+ };
+
/* Custom board node with GPIO pins to active etc */
usb-s8815 {
/* The S8815 is using this very GPIO pin for the SMSC91x IRQs */
ethernet-gpio {
- gpios = <&gpio3 19 0x1>;
- interrupts = <19 0x1>;
- interrupt-parent = <&gpio3>;
+ gpios = <&gpio3 8 0x1>;
};
/* This will bias the MMC/SD card detect line */
mmcsd-gpio {
bootargs = "earlyprintk console=ttyS0,115200";
};
- soc {
- uart0: uart@01c28000 {
+ soc@01c20000 {
+ uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V6=y
CONFIG_ARCH_OMAP2PLUS=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_DEVICEFS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
CONFIG_MEDIA_USB_SUPPORT=y
CONFIG_USB_VIDEO_CLASS=m
CONFIG_DRM=y
+CONFIG_TEGRA_HOST1X=y
CONFIG_DRM_TEGRA=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_STAGING=y
CONFIG_SENSORS_ISL29018=y
CONFIG_SENSORS_ISL29028=y
-CONFIG_SENSORS_AK8975=y
+CONFIG_AK8975=y
CONFIG_MFD_NVEC=y
CONFIG_KEYBOARD_NVEC=y
CONFIG_SERIO_NVEC_PS2=y
add r3,r3,r10 @ E+=F_00_19(B,C,D)
cmp r14,sp
bne .L_00_15 @ [((11+4)*5+2)*3]
+ sub sp,sp,#25*4
#if __ARM_ARCH__<7
ldrb r10,[r1,#2]
ldrb r9,[r1,#3]
add r3,r3,r10 @ E+=F_00_19(B,C,D)
ldr r8,.LK_20_39 @ [+15+16*4]
- sub sp,sp,#25*4
cmn sp,#0 @ [+3], clear carry to denote 20_39
.L_20_39_or_60_79:
ldr r9,[r14,#15*4]
--- /dev/null
+/*
+ * arch/arm/include/asm/hugetlb-3level.h
+ *
+ * Copyright (C) 2012 ARM Ltd.
+ *
+ * Based on arch/x86/include/asm/hugetlb.h.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _ASM_ARM_HUGETLB_3LEVEL_H
+#define _ASM_ARM_HUGETLB_3LEVEL_H
+
+
+/*
+ * If our huge pte is non-zero then mark the valid bit.
+ * This allows pte_present(huge_ptep_get(ptep)) to return true for non-zero
+ * ptes.
+ * (The valid bit is automatically cleared by set_pte_at for PROT_NONE ptes).
+ */
+static inline pte_t huge_ptep_get(pte_t *ptep)
+{
+ pte_t retval = *ptep;
+ if (pte_val(retval))
+ pte_val(retval) |= L_PTE_VALID;
+ return retval;
+}
+
+static inline void set_huge_pte_at(struct mm_struct *mm, unsigned long addr,
+ pte_t *ptep, pte_t pte)
+{
+ set_pte_at(mm, addr, ptep, pte);
+}
+
+static inline void huge_ptep_clear_flush(struct vm_area_struct *vma,
+ unsigned long addr, pte_t *ptep)
+{
+ ptep_clear_flush(vma, addr, ptep);
+}
+
+static inline void huge_ptep_set_wrprotect(struct mm_struct *mm,
+ unsigned long addr, pte_t *ptep)
+{
+ ptep_set_wrprotect(mm, addr, ptep);
+}
+
+static inline pte_t huge_ptep_get_and_clear(struct mm_struct *mm,
+ unsigned long addr, pte_t *ptep)
+{
+ return ptep_get_and_clear(mm, addr, ptep);
+}
+
+static inline int huge_ptep_set_access_flags(struct vm_area_struct *vma,
+ unsigned long addr, pte_t *ptep,
+ pte_t pte, int dirty)
+{
+ return ptep_set_access_flags(vma, addr, ptep, pte, dirty);
+}
+
+#endif /* _ASM_ARM_HUGETLB_3LEVEL_H */
--- /dev/null
+/*
+ * arch/arm/include/asm/hugetlb.h
+ *
+ * Copyright (C) 2012 ARM Ltd.
+ *
+ * Based on arch/x86/include/asm/hugetlb.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef _ASM_ARM_HUGETLB_H
+#define _ASM_ARM_HUGETLB_H
+
+#include <asm/page.h>
+#include <asm-generic/hugetlb.h>
+
+#include <asm/hugetlb-3level.h>
+
+static inline void hugetlb_free_pgd_range(struct mmu_gather *tlb,
+ unsigned long addr, unsigned long end,
+ unsigned long floor,
+ unsigned long ceiling)
+{
+ free_pgd_range(tlb, addr, end, floor, ceiling);
+}
+
+
+static inline int is_hugepage_only_range(struct mm_struct *mm,
+ unsigned long addr, unsigned long len)
+{
+ return 0;
+}
+
+static inline int prepare_hugepage_range(struct file *file,
+ unsigned long addr, unsigned long len)
+{
+ struct hstate *h = hstate_file(file);
+ if (len & ~huge_page_mask(h))
+ return -EINVAL;
+ if (addr & ~huge_page_mask(h))
+ return -EINVAL;
+ return 0;
+}
+
+static inline void hugetlb_prefault_arch_hook(struct mm_struct *mm)
+{
+}
+
+static inline int huge_pte_none(pte_t pte)
+{
+ return pte_none(pte);
+}
+
+static inline pte_t huge_pte_wrprotect(pte_t pte)
+{
+ return pte_wrprotect(pte);
+}
+
+static inline int arch_prepare_hugepage(struct page *page)
+{
+ return 0;
+}
+
+static inline void arch_release_hugepage(struct page *page)
+{
+}
+
+static inline void arch_clear_hugepage_flags(struct page *page)
+{
+ clear_bit(PG_dcache_clean, &page->flags);
+}
+
+#endif /* _ASM_ARM_HUGETLB_H */
#define PMD_TYPE_FAULT (_AT(pmdval_t, 0) << 0)
#define PMD_TYPE_TABLE (_AT(pmdval_t, 3) << 0)
#define PMD_TYPE_SECT (_AT(pmdval_t, 1) << 0)
+#define PMD_TABLE_BIT (_AT(pmdval_t, 1) << 1)
#define PMD_BIT4 (_AT(pmdval_t, 0))
#define PMD_DOMAIN(x) (_AT(pmdval_t, 0))
#define PMD_APTABLE_SHIFT (61)
*/
#define PMD_SECT_BUFFERABLE (_AT(pmdval_t, 1) << 2)
#define PMD_SECT_CACHEABLE (_AT(pmdval_t, 1) << 3)
+#define PMD_SECT_USER (_AT(pmdval_t, 1) << 6) /* AP[1] */
+#define PMD_SECT_RDONLY (_AT(pmdval_t, 1) << 7) /* AP[2] */
#define PMD_SECT_S (_AT(pmdval_t, 3) << 8)
#define PMD_SECT_AF (_AT(pmdval_t, 1) << 10)
#define PMD_SECT_nG (_AT(pmdval_t, 1) << 11)
#define PTE_TYPE_MASK (_AT(pteval_t, 3) << 0)
#define PTE_TYPE_FAULT (_AT(pteval_t, 0) << 0)
#define PTE_TYPE_PAGE (_AT(pteval_t, 3) << 0)
+#define PTE_TABLE_BIT (_AT(pteval_t, 1) << 1)
#define PTE_BUFFERABLE (_AT(pteval_t, 1) << 2) /* AttrIndx[0] */
#define PTE_CACHEABLE (_AT(pteval_t, 1) << 3) /* AttrIndx[1] */
#define PTE_EXT_SHARED (_AT(pteval_t, 3) << 8) /* SH[1:0], inner shareable */
#define USER_PTRS_PER_PGD (PAGE_OFFSET / PGDIR_SIZE)
+/*
+ * Hugetlb definitions.
+ */
+#define HPAGE_SHIFT PMD_SHIFT
+#define HPAGE_SIZE (_AC(1, UL) << HPAGE_SHIFT)
+#define HPAGE_MASK (~(HPAGE_SIZE - 1))
+#define HUGETLB_PAGE_ORDER (HPAGE_SHIFT - PAGE_SHIFT)
+
/*
* "Linux" PTE definitions for LPAE.
*
#define L_PTE_SPECIAL (_AT(pteval_t, 1) << 56) /* unused */
#define L_PTE_NONE (_AT(pteval_t, 1) << 57) /* PROT_NONE */
+#define PMD_SECT_VALID (_AT(pmdval_t, 1) << 0)
+#define PMD_SECT_DIRTY (_AT(pmdval_t, 1) << 55)
+#define PMD_SECT_SPLITTING (_AT(pmdval_t, 1) << 56)
+#define PMD_SECT_NONE (_AT(pmdval_t, 1) << 57)
+
/*
* To be used in assembly code with the upper page attributes.
*/
clean_pmd_entry(pmdp); \
} while (0)
+/*
+ * For 3 levels of paging the PTE_EXT_NG bit will be set for user address ptes
+ * that are written to a page table but not for ptes created with mk_pte.
+ *
+ * In hugetlb_no_page, a new huge pte (new_pte) is generated and passed to
+ * hugetlb_cow, where it is compared with an entry in a page table.
+ * This comparison test fails erroneously leading ultimately to a memory leak.
+ *
+ * To correct this behaviour, we mask off PTE_EXT_NG for any pte that is
+ * present before running the comparison.
+ */
+#define __HAVE_ARCH_PTE_SAME
+#define pte_same(pte_a,pte_b) ((pte_present(pte_a) ? pte_val(pte_a) & ~PTE_EXT_NG \
+ : pte_val(pte_a)) \
+ == (pte_present(pte_b) ? pte_val(pte_b) & ~PTE_EXT_NG \
+ : pte_val(pte_b)))
+
#define set_pte_ext(ptep,pte,ext) cpu_set_pte_ext(ptep,__pte(pte_val(pte)|(ext)))
+#define pte_huge(pte) (pte_val(pte) && !(pte_val(pte) & PTE_TABLE_BIT))
+#define pte_mkhuge(pte) (__pte(pte_val(pte) & ~PTE_TABLE_BIT))
+
+#define pmd_young(pmd) (pmd_val(pmd) & PMD_SECT_AF)
+
+#define __HAVE_ARCH_PMD_WRITE
+#define pmd_write(pmd) (!(pmd_val(pmd) & PMD_SECT_RDONLY))
+
+#ifdef CONFIG_TRANSPARENT_HUGEPAGE
+#define pmd_trans_huge(pmd) (pmd_val(pmd) && !(pmd_val(pmd) & PMD_TABLE_BIT))
+#define pmd_trans_splitting(pmd) (pmd_val(pmd) & PMD_SECT_SPLITTING)
+#endif
+
+#define PMD_BIT_FUNC(fn,op) \
+static inline pmd_t pmd_##fn(pmd_t pmd) { pmd_val(pmd) op; return pmd; }
+
+PMD_BIT_FUNC(wrprotect, |= PMD_SECT_RDONLY);
+PMD_BIT_FUNC(mkold, &= ~PMD_SECT_AF);
+PMD_BIT_FUNC(mksplitting, |= PMD_SECT_SPLITTING);
+PMD_BIT_FUNC(mkwrite, &= ~PMD_SECT_RDONLY);
+PMD_BIT_FUNC(mkdirty, |= PMD_SECT_DIRTY);
+PMD_BIT_FUNC(mkyoung, |= PMD_SECT_AF);
+
+#define pmd_mkhuge(pmd) (__pmd(pmd_val(pmd) & ~PMD_TABLE_BIT))
+
+#define pmd_pfn(pmd) (((pmd_val(pmd) & PMD_MASK) & PHYS_MASK) >> PAGE_SHIFT)
+#define pfn_pmd(pfn,prot) (__pmd(((phys_addr_t)(pfn) << PAGE_SHIFT) | pgprot_val(prot)))
+#define mk_pmd(page,prot) pfn_pmd(page_to_pfn(page),prot)
+
+/* represent a notpresent pmd by zero, this is used by pmdp_invalidate */
+#define pmd_mknotpresent(pmd) (__pmd(0))
+
+static inline pmd_t pmd_modify(pmd_t pmd, pgprot_t newprot)
+{
+ const pmdval_t mask = PMD_SECT_USER | PMD_SECT_XN | PMD_SECT_RDONLY |
+ PMD_SECT_VALID | PMD_SECT_NONE;
+ pmd_val(pmd) = (pmd_val(pmd) & ~mask) | (pgprot_val(newprot) & mask);
+ return pmd;
+}
+
+static inline void set_pmd_at(struct mm_struct *mm, unsigned long addr,
+ pmd_t *pmdp, pmd_t pmd)
+{
+ BUG_ON(addr >= TASK_SIZE);
+
+ /* create a faulting entry if PROT_NONE protected */
+ if (pmd_val(pmd) & PMD_SECT_NONE)
+ pmd_val(pmd) &= ~PMD_SECT_VALID;
+
+ *pmdp = __pmd(pmd_val(pmd) | PMD_SECT_nG);
+ flush_pmd_entry(pmdp);
+}
+
+static inline int has_transparent_hugepage(void)
+{
+ return 1;
+}
+
#endif /* __ASSEMBLY__ */
#endif /* _ASM_PGTABLE_3LEVEL_H */
#include <asm/memory.h>
#include <asm/pgtable-hwdef.h>
+
+#include <asm/tlbflush.h>
+
#ifdef CONFIG_ARM_LPAE
#include <asm/pgtable-3level.h>
#else
#endif
}
+static inline void
+tlb_remove_pmd_tlb_entry(struct mmu_gather *tlb, pmd_t *pmdp, unsigned long addr)
+{
+ tlb_add_flush(tlb, addr);
+}
+
#define pte_free_tlb(tlb, ptep, addr) __pte_free_tlb(tlb, ptep, addr)
#define pmd_free_tlb(tlb, pmdp, addr) __pmd_free_tlb(tlb, pmdp, addr)
#define pud_free_tlb(tlb, pudp, addr) pud_free((tlb)->mm, pudp)
}
#endif
+#define update_mmu_cache_pmd(vma, address, pmd) do { } while (0)
+
#endif
#elif defined(CONFIG_SMP) /* !CONFIG_MMU */
#define U8500_UART0_PHYS_BASE (0x80120000)
#define U8500_UART1_PHYS_BASE (0x80121000)
#define U8500_UART2_PHYS_BASE (0x80007000)
-#define U8500_UART0_VIRT_BASE (0xa8120000)
-#define U8500_UART1_VIRT_BASE (0xa8121000)
-#define U8500_UART2_VIRT_BASE (0xa8007000)
+#define U8500_UART0_VIRT_BASE (0xf8120000)
+#define U8500_UART1_VIRT_BASE (0xf8121000)
+#define U8500_UART2_VIRT_BASE (0xf8007000)
#define __UX500_PHYS_UART(n) U8500_UART##n##_PHYS_BASE
#define __UX500_VIRT_UART(n) U8500_UART##n##_VIRT_BASE
#endif
.vm_start = 0xffff0000,
.vm_end = 0xffff0000 + PAGE_SIZE,
.vm_flags = VM_READ | VM_EXEC | VM_MAYREAD | VM_MAYEXEC,
- .vm_mm = &init_mm,
};
static int __init gate_vma_init(void)
static struct clock_event_device clkevt = {
.name = "at91_tick",
.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 32,
.rating = 150,
.set_next_event = clkevt32k_next_event,
.set_mode = clkevt32k_mode,
at91_st_write(AT91_ST_RTMR, 1);
/* Setup timer clockevent, with minimum of two ticks (important!!) */
+ clkevt.mult = div_sc(AT91_SLOW_CLOCK, NSEC_PER_SEC, clkevt.shift);
+ clkevt.max_delta_ns = clockevent_delta2ns(AT91_ST_ALMV, &clkevt);
+ clkevt.min_delta_ns = clockevent_delta2ns(2, &clkevt) + 1;
clkevt.cpumask = cpumask_of(0);
- clockevents_config_and_register(&clkevt, AT91_SLOW_CLOCK,
- 2, AT91_ST_ALMV);
+ clockevents_register_device(&clkevt);
/* register clocksource */
clocksource_register_hz(&clk32k, AT91_SLOW_CLOCK);
at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
}
-void __init at91sam9n12_initialize(void)
-{
- at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0);
-}
-
AT91_SOC_START(at91sam9n12)
.map_io = at91sam9n12_map_io,
.register_clocks = at91sam9n12_register_clocks,
- .init = at91sam9n12_initialize,
AT91_SOC_END
#define AT91_PMC_PCR_CMD (0x1 << 12) /* Command (read=0, write=1) */
#define AT91_PMC_PCR_DIV(n) ((n) << 16) /* Divisor Value */
#define AT91_PMC_PCR_DIV0 0x0 /* Peripheral clock is MCK */
-#define AT91_PMC_PCR_DIV2 0x2 /* Peripheral clock is MCK/2 */
-#define AT91_PMC_PCR_DIV4 0x4 /* Peripheral clock is MCK/4 */
-#define AT91_PMC_PCR_DIV8 0x8 /* Peripheral clock is MCK/8 */
+#define AT91_PMC_PCR_DIV2 0x1 /* Peripheral clock is MCK/2 */
+#define AT91_PMC_PCR_DIV4 0x2 /* Peripheral clock is MCK/4 */
+#define AT91_PMC_PCR_DIV8 0x3 /* Peripheral clock is MCK/8 */
#define AT91_PMC_PCR_EN (0x1 << 28) /* Enable */
#endif
static const char *step_sels[] = { "osc", "pll2_pfd2_396m", };
static const char *pll1_sw_sels[] = { "pll1_sys", "step", };
static const char *periph_pre_sels[] = { "pll2_bus", "pll2_pfd2_396m", "pll2_pfd0_352m", "pll2_198m", };
-static const char *periph_clk2_sels[] = { "pll3_usb_otg", "osc", };
+static const char *periph_clk2_sels[] = { "pll3_usb_otg", "osc", "osc", "dummy", };
+static const char *periph2_clk2_sels[] = { "pll3_usb_otg", "pll2_bus", };
static const char *periph_sels[] = { "periph_pre", "periph_clk2", };
static const char *periph2_sels[] = { "periph2_pre", "periph2_clk2", };
static const char *axi_sels[] = { "periph", "pll2_pfd2_396m", "pll3_pfd1_540m", };
static const char *gpu_axi_sels[] = { "axi", "ahb", };
static const char *gpu2d_core_sels[] = { "axi", "pll3_usb_otg", "pll2_pfd0_352m", "pll2_pfd2_396m", };
static const char *gpu3d_core_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd2_396m", };
-static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd9_720m", };
+static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll3_pfd0_720m", };
static const char *ipu_sels[] = { "mmdc_ch0_axi", "pll2_pfd2_396m", "pll3_120m", "pll3_pfd1_540m", };
static const char *ldb_di_sels[] = { "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "mmdc_ch1_axi", "pll3_usb_otg", };
static const char *ipu_di_pre_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll5_video_div", "pll2_pfd0_352m", "pll2_pfd2_396m", "pll3_pfd1_540m", };
clk[pll1_sw] = imx_clk_mux("pll1_sw", base + 0xc, 2, 1, pll1_sw_sels, ARRAY_SIZE(pll1_sw_sels));
clk[periph_pre] = imx_clk_mux("periph_pre", base + 0x18, 18, 2, periph_pre_sels, ARRAY_SIZE(periph_pre_sels));
clk[periph2_pre] = imx_clk_mux("periph2_pre", base + 0x18, 21, 2, periph_pre_sels, ARRAY_SIZE(periph_pre_sels));
- clk[periph_clk2_sel] = imx_clk_mux("periph_clk2_sel", base + 0x18, 12, 1, periph_clk2_sels, ARRAY_SIZE(periph_clk2_sels));
- clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph_clk2_sels, ARRAY_SIZE(periph_clk2_sels));
+ clk[periph_clk2_sel] = imx_clk_mux("periph_clk2_sel", base + 0x18, 12, 2, periph_clk2_sels, ARRAY_SIZE(periph_clk2_sels));
+ clk[periph2_clk2_sel] = imx_clk_mux("periph2_clk2_sel", base + 0x18, 20, 1, periph2_clk2_sels, ARRAY_SIZE(periph2_clk2_sels));
clk[axi_sel] = imx_clk_mux("axi_sel", base + 0x14, 6, 2, axi_sels, ARRAY_SIZE(axi_sels));
clk[esai_sel] = imx_clk_mux("esai_sel", base + 0x20, 19, 2, audio_sels, ARRAY_SIZE(audio_sels));
clk[asrc_sel] = imx_clk_mux("asrc_sel", base + 0x30, 7, 2, audio_sels, ARRAY_SIZE(audio_sels));
clk[ldb_di1] = imx_clk_gate2("ldb_di1", "ldb_di1_podf", base + 0x74, 14);
clk[ipu2_di1] = imx_clk_gate2("ipu2_di1", "ipu2_di1_sel", base + 0x74, 10);
clk[hsi_tx] = imx_clk_gate2("hsi_tx", "hsi_tx_podf", base + 0x74, 16);
- clk[mlb] = imx_clk_gate2("mlb", "pll8_mlb", base + 0x74, 18);
+ clk[mlb] = imx_clk_gate2("mlb", "axi", base + 0x74, 18);
clk[mmdc_ch0_axi] = imx_clk_gate2("mmdc_ch0_axi", "mmdc_ch0_axi_podf", base + 0x74, 20);
clk[mmdc_ch1_axi] = imx_clk_gate2("mmdc_ch1_axi", "mmdc_ch1_axi_podf", base + 0x74, 22);
clk[ocram] = imx_clk_gate2("ocram", "ahb", base + 0x74, 28);
.section ".text.head", "ax"
#ifdef CONFIG_SMP
+diag_reg_offset:
+ .word g_diag_reg - .
+
+ .macro set_diag_reg
+ adr r0, diag_reg_offset
+ ldr r1, [r0]
+ add r1, r1, r0 @ r1 = physical &g_diag_reg
+ ldr r0, [r1]
+ mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register
+ .endm
+
ENTRY(v7_secondary_startup)
bl v7_invalidate_l1
+ set_diag_reg
b secondary_startup
ENDPROC(v7_secondary_startup)
#endif
#include <linux/init.h>
#include <linux/smp.h>
+#include <asm/cacheflush.h>
#include <asm/page.h>
#include <asm/smp_scu.h>
#include <asm/mach/map.h>
#define SCU_STANDBY_ENABLE (1 << 5)
+u32 g_diag_reg;
static void __iomem *scu_base;
static struct map_desc scu_io_desc __initdata = {
static void __init imx_smp_prepare_cpus(unsigned int max_cpus)
{
imx_smp_prepare();
+
+ /*
+ * The diagnostic register holds the errata bits. Mostly bootloader
+ * does not bring up secondary cores, so that when errata bits are set
+ * in bootloader, they are set only for boot cpu. But on a SMP
+ * configuration, it should be equally done on every single core.
+ * Read the register from boot cpu here, and will replicate it into
+ * secondary cores when booting them.
+ */
+ asm("mrc p15, 0, %0, c15, c0, 1" : "=r" (g_diag_reg) : : "cc");
+ __cpuc_flush_dcache_area(&g_diag_reg, sizeof(g_diag_reg));
+ outer_clean_range(__pa(&g_diag_reg), __pa(&g_diag_reg + 1));
}
struct smp_operations imx_smp_ops __initdata = {
{
orion_time_set_base(TIMER_VIRT_BASE);
- /*
- * Some Kirkwood devices allocate their coherent buffers from atomic
- * context. Increase size of atomic coherent pool to make sure such
- * the allocations won't fail.
- */
- init_dma_coherent_pool_size(SZ_1M);
mvebu_mbus_init("marvell,kirkwood-mbus",
BRIDGE_WINS_BASE, BRIDGE_WINS_SZ,
DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ);
static int __init ts219_pci_init(void)
{
if (machine_is_ts219())
- kirkwood_pcie_init(KW_PCIE0);
+ kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0);
return 0;
}
select MVEBU_CLK_GATING
select MVEBU_MBUS
select ZONE_DMA if ARM_LPAE
+ select ARCH_REQUIRE_GPIOLIB
if ARCH_MVEBU
{
char *mbus_soc_name;
- /*
- * Some Armada 370/XP devices allocate their coherent buffers
- * from atomic context. Increase size of atomic coherent pool
- * to make sure such the allocations won't fail.
- */
- init_dma_coherent_pool_size(SZ_1M);
-
/*
* This initialization will be replaced by a DT-based
* initialization once the mvebu-mbus driver gains DT support.
dev_err(&pdev->dev,
"%s: Memory allocation failed for d->chan!\n",
__func__);
+ ret = -ENOMEM;
goto exit_release_d;
}
*/
DEFINE_CLK_FIXED_FACTOR(clkdiv32k_ck, "clk_24mhz", &clk_24mhz, 0x0, 1, 732);
-DEFINE_CLK_GATE(clkdiv32k_ick, "clkdiv32k_ck", &clkdiv32k_ck, 0x0,
- AM33XX_CM_PER_CLKDIV32K_CLKCTRL, AM33XX_MODULEMODE_SWCTRL_SHIFT,
- 0x0, NULL);
+static struct clk clkdiv32k_ick;
+
+static const char *clkdiv32k_ick_parent_names[] = {
+ "clkdiv32k_ck",
+};
+
+static const struct clk_ops clkdiv32k_ick_ops = {
+ .enable = &omap2_dflt_clk_enable,
+ .disable = &omap2_dflt_clk_disable,
+ .is_enabled = &omap2_dflt_clk_is_enabled,
+ .init = &omap2_init_clk_clkdm,
+};
+
+static struct clk_hw_omap clkdiv32k_ick_hw = {
+ .hw = {
+ .clk = &clkdiv32k_ick,
+ },
+ .enable_reg = AM33XX_CM_PER_CLKDIV32K_CLKCTRL,
+ .enable_bit = AM33XX_MODULEMODE_SWCTRL_SHIFT,
+ .clkdm_name = "clk_24mhz_clkdm",
+};
+
+DEFINE_STRUCT_CLK(clkdiv32k_ick, clkdiv32k_ick_parent_names, clkdiv32k_ick_ops);
/* "usbotg_fck" is an additional clock and not really a modulemode */
DEFINE_CLK_GATE(usbotg_fck, "dpll_per_ck", &dpll_per_ck, 0x0,
clkdm = _get_clkdm(oh);
if (sf & SYSC_HAS_SIDLEMODE) {
+ if (oh->flags & HWMOD_SWSUP_SIDLE ||
+ oh->flags & HWMOD_SWSUP_SIDLE_ACT) {
+ idlemode = HWMOD_IDLEMODE_NO;
+ } else {
+ if (sf & SYSC_HAS_ENAWAKEUP)
+ _enable_wakeup(oh, &v);
+ if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+ idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
+ }
+
+ /*
+ * This is special handling for some IPs like
+ * 32k sync timer. Force them to idle!
+ */
clkdm_act = (clkdm && clkdm->flags & CLKDM_ACTIVE_WITH_MPU);
if (clkdm_act && !(oh->class->sysc->idlemodes &
(SIDLE_SMART | SIDLE_SMART_WKUP)))
idlemode = HWMOD_IDLEMODE_FORCE;
- else
- idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
- HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
+
_set_slave_idlemode(oh, idlemode, &v);
}
(sf & SYSC_HAS_CLOCKACTIVITY))
_set_clockactivity(oh, oh->class->sysc->clockact, &v);
- /* If slave is in SMARTIDLE, also enable wakeup */
- if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
- _enable_wakeup(oh, &v);
-
_write_sysconfig(v, oh);
/*
sf = oh->class->sysc->sysc_flags;
if (sf & SYSC_HAS_SIDLEMODE) {
- /* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */
- if (oh->flags & HWMOD_SWSUP_SIDLE ||
- !(oh->class->sysc->idlemodes &
- (SIDLE_SMART | SIDLE_SMART_WKUP)))
+ if (oh->flags & HWMOD_SWSUP_SIDLE) {
idlemode = HWMOD_IDLEMODE_FORCE;
- else
- idlemode = HWMOD_IDLEMODE_SMART;
+ } else {
+ if (sf & SYSC_HAS_ENAWAKEUP)
+ _enable_wakeup(oh, &v);
+ if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
+ idlemode = HWMOD_IDLEMODE_SMART_WKUP;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
+ }
_set_slave_idlemode(oh, idlemode, &v);
}
_set_master_standbymode(oh, idlemode, &v);
}
- /* If slave is in SMARTIDLE, also enable wakeup */
- if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
- _enable_wakeup(oh, &v);
-
_write_sysconfig(v, oh);
}
* do so is present in the hwmod data, then call it and pass along the
* return value; otherwise, return 0.
*/
-static int __init _enable_preprogram(struct omap_hwmod *oh)
+static int _enable_preprogram(struct omap_hwmod *oh)
{
if (!oh->class->enable_preprogram)
return 0;
return 0;
}
-/**
- * omap_hwmod_set_ocp_autoidle - set the hwmod's OCP autoidle bit
- * @oh: struct omap_hwmod *
- * @autoidle: desired AUTOIDLE bitfield value (0 or 1)
- *
- * Sets the IP block's OCP autoidle bit in hardware, and updates our
- * local copy. Intended to be used by drivers that require
- * direct manipulation of the AUTOIDLE bits.
- * Returns -EINVAL if @oh is null or is not in the ENABLED state, or passes
- * along the return value from _set_module_autoidle().
- *
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle)
-{
- u32 v;
- int retval = 0;
- unsigned long flags;
-
- if (!oh || oh->_state != _HWMOD_STATE_ENABLED)
- return -EINVAL;
-
- spin_lock_irqsave(&oh->_lock, flags);
-
- v = oh->_sysc_cache;
-
- retval = _set_module_autoidle(oh, autoidle, &v);
-
- if (!retval)
- _write_sysconfig(v, oh);
-
- spin_unlock_irqrestore(&oh->_lock, flags);
-
- return retval;
-}
-
/**
* _shutdown - shutdown an omap_hwmod
* @oh: struct omap_hwmod *
return ret;
}
-/**
- * omap_hwmod_set_slave_idlemode - set the hwmod's OCP slave idlemode
- * @oh: struct omap_hwmod *
- * @idlemode: SIDLEMODE field bits (shifted to bit 0)
- *
- * Sets the IP block's OCP slave idlemode in hardware, and updates our
- * local copy. Intended to be used by drivers that have some erratum
- * that requires direct manipulation of the SIDLEMODE bits. Returns
- * -EINVAL if @oh is null, or passes along the return value from
- * _set_slave_idlemode().
- *
- * XXX Does this function have any current users? If not, we should
- * remove it; it is better to let the rest of the hwmod code handle this.
- * Any users of this function should be scrutinized carefully.
- */
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode)
-{
- u32 v;
- int retval = 0;
-
- if (!oh)
- return -EINVAL;
-
- v = oh->_sysc_cache;
-
- retval = _set_slave_idlemode(oh, idlemode, &v);
- if (!retval)
- _write_sysconfig(v, oh);
-
- return retval;
-}
-
/**
* omap_hwmod_lookup - look up a registered omap_hwmod by name
* @name: name of the omap_hwmod to look up
* is kept in force-standby mode. Failing to do so causes PM problems
* with musb on OMAP3630 at least. Note that musb has a dedicated register
* to control MSTANDBY signal when MIDLEMODE is set to force-standby.
+ * HWMOD_SWSUP_SIDLE_ACT: omap_hwmod code should manually bring the module
+ * out of idle, but rely on smart-idle to the put it back in idle,
+ * so the wakeups are still functional (Only known case for now is UART)
*/
#define HWMOD_SWSUP_SIDLE (1 << 0)
#define HWMOD_SWSUP_MSTANDBY (1 << 1)
#define HWMOD_EXT_OPT_MAIN_CLK (1 << 9)
#define HWMOD_BLOCK_WFI (1 << 10)
#define HWMOD_FORCE_MSTANDBY (1 << 11)
+#define HWMOD_SWSUP_SIDLE_ACT (1 << 12)
/*
* omap_hwmod._int_flags definitions
int omap_hwmod_enable_clocks(struct omap_hwmod *oh);
int omap_hwmod_disable_clocks(struct omap_hwmod *oh);
-int omap_hwmod_set_slave_idlemode(struct omap_hwmod *oh, u8 idlemode);
-int omap_hwmod_set_ocp_autoidle(struct omap_hwmod *oh, u8 autoidle);
-
int omap_hwmod_reset(struct omap_hwmod *oh);
void omap_hwmod_ocp_barrier(struct omap_hwmod *oh);
.mpu_irqs = omap2_uart1_mpu_irqs,
.sdma_reqs = omap2_uart1_sdma_reqs,
.main_clk = "uart1_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart2_mpu_irqs,
.sdma_reqs = omap2_uart2_sdma_reqs,
.main_clk = "uart2_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart3_mpu_irqs,
.sdma_reqs = omap2_uart3_sdma_reqs,
.main_clk = "uart3_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.name = "uart1",
.class = &uart_class,
.clkdm_name = "l4_wkup_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart1_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_wkupdm_ck",
.name = "uart2",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart2_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart3",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart3_irqs,
.sdma_reqs = uart3_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart4",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart4_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart5",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart5_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.name = "uart6",
.class = &uart_class,
.clkdm_name = "l4ls_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = am33xx_uart6_irqs,
.sdma_reqs = uart1_edma_reqs,
.main_clk = "dpll_per_m2_div4_ck",
.mpu_irqs = omap2_uart1_mpu_irqs,
.sdma_reqs = omap2_uart1_sdma_reqs,
.main_clk = "uart1_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart2_mpu_irqs,
.sdma_reqs = omap2_uart2_sdma_reqs,
.main_clk = "uart2_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = CORE_MOD,
.mpu_irqs = omap2_uart3_mpu_irqs,
.sdma_reqs = omap2_uart3_sdma_reqs,
.main_clk = "uart3_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = OMAP3430_PER_MOD,
.mpu_irqs = uart4_mpu_irqs,
.sdma_reqs = uart4_sdma_reqs,
.main_clk = "uart4_fck",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.prcm = {
.omap2 = {
.module_offs = OMAP3430_PER_MOD,
.name = "uart1",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart1_irqs,
.sdma_reqs = omap44xx_uart1_sdma_reqs,
.main_clk = "func_48m_fclk",
.name = "uart2",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart2_irqs,
.sdma_reqs = omap44xx_uart2_sdma_reqs,
.main_clk = "func_48m_fclk",
.name = "uart3",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
- .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET,
+ .flags = HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET |
+ HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart3_irqs,
.sdma_reqs = omap44xx_uart3_sdma_reqs,
.main_clk = "func_48m_fclk",
.name = "uart4",
.class = &omap44xx_uart_hwmod_class,
.clkdm_name = "l4_per_clkdm",
+ .flags = HWMOD_SWSUP_SIDLE_ACT,
.mpu_irqs = omap44xx_uart4_irqs,
.sdma_reqs = omap44xx_uart4_sdma_reqs,
.main_clk = "func_48m_fclk",
omap_hwmod_disable_wakeup(od->hwmods[0]);
}
-/*
- * Errata i291: [UART]:Cannot Acknowledge Idle Requests
- * in Smartidle Mode When Configured for DMA Operations.
- * WA: configure uart in force idle mode.
- */
-static void omap_uart_set_noidle(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct omap_device *od = to_omap_device(pdev);
-
- omap_hwmod_set_slave_idlemode(od->hwmods[0], HWMOD_IDLEMODE_NO);
-}
-
-static void omap_uart_set_smartidle(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct omap_device *od = to_omap_device(pdev);
- u8 idlemode;
-
- if (od->hwmods[0]->class->sysc->idlemodes & SIDLE_SMART_WKUP)
- idlemode = HWMOD_IDLEMODE_SMART_WKUP;
- else
- idlemode = HWMOD_IDLEMODE_SMART;
-
- omap_hwmod_set_slave_idlemode(od->hwmods[0], idlemode);
-}
-
#else
static void omap_uart_enable_wakeup(struct device *dev, bool enable)
{}
-static void omap_uart_set_noidle(struct device *dev) {}
-static void omap_uart_set_smartidle(struct device *dev) {}
#endif /* CONFIG_PM */
#ifdef CONFIG_OMAP_MUX
omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
omap_up.flags = UPF_BOOT_AUTOCONF;
omap_up.get_context_loss_count = omap_pm_get_dev_context_loss_count;
- omap_up.set_forceidle = omap_uart_set_smartidle;
- omap_up.set_noidle = omap_uart_set_noidle;
omap_up.enable_wakeup = omap_uart_enable_wakeup;
omap_up.dma_rx_buf_size = info->dma_rx_buf_size;
omap_up.dma_rx_timeout = info->dma_rx_timeout;
orion_time_set_base(TIMER_VIRT_BASE);
- /*
- * Some Orion5x devices allocate their coherent buffers from atomic
- * context. Increase size of atomic coherent pool to make sure such
- * the allocations won't fail.
- */
- init_dma_coherent_pool_size(SZ_1M);
-
/* Initialize the MBUS driver */
orion5x_pcie_id(&dev, &rev);
if (dev == MV88F5281_DEV_ID)
static struct usb_phy *phy;
static int usb_power_on(struct platform_device *pdev)
{
- if (!phy)
- return -EIO;
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
static void usb_power_off(struct platform_device *pdev)
{
- if (!phy)
+ if (IS_ERR(phy))
return;
usb_phy_shutdown(phy);
config ARCH_SUNXI
bool "Allwinner A1X SOCs" if ARCH_MULTI_V7
+ select ARCH_REQUIRE_GPIOLIB
select CLKSRC_MMIO
select CLKSRC_OF
select COMMON_CLK
bool "U8500 Development platform, MOP500 versions"
select I2C
select I2C_NOMADIK
+ select REGULATOR
select REGULATOR_FIXED_VOLTAGE
select SOC_BUS
select UX500_SOC_DB8500
sdi0_reg_info.gpios[0].gpio = GPIO_SDMMC_1V8_3V_SEL;
mop500_pinmaps_init();
- parent = u8500_init_devices(&ab8500_platdata);
+ parent = u8500_init_devices();
for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
mop500_platform_devs[i]->dev.parent = parent;
sdi0_reg_info.gpios[0].gpio = SNOWBALL_SDMMC_1V8_3V_GPIO;
snowball_pinmaps_init();
- parent = u8500_init_devices(&ab8500_platdata);
+ parent = u8500_init_devices();
for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
snowball_platform_devs[i]->dev.parent = parent;
sdi0_reg_info.gpios[0].gpio = HREFV60_SDMMC_1V8_3V_GPIO;
hrefv60_pinmaps_init();
- parent = u8500_init_devices(&ab8500_platdata);
+ parent = u8500_init_devices();
for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
mop500_platform_devs[i]->dev.parent = parent;
/*
* This function is called from the board init
*/
-struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500)
+struct device * __init u8500_init_devices(void)
{
struct device *parent;
int i;
for (i = 0; i < ARRAY_SIZE(platform_devs); i++)
platform_devs[i]->dev.parent = parent;
- db8500_prcmu_device.dev.platform_data = ab8500;
-
platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
return parent;
OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
&db8500_prcmu_pdata),
- OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x", NULL),
+ OF_DEV_AUXDATA("smsc,lan9115", 0x50000000, "smsc911x.0", NULL),
/* Requires device name bindings. */
OF_DEV_AUXDATA("stericsson,nmk-pinctrl", U8500_PRCMU_BASE,
"pinctrl-db8500", NULL),
void __init ux500_map_io(void);
extern void __init u8500_map_io(void);
-extern struct device * __init u8500_init_devices(struct ab8500_platform_data *ab8500);
+extern struct device * __init u8500_init_devices(void);
extern void __init ux500_init_irq(void);
extern void __init ux500_init_late(void);
"wm,wm8505",
"wm,wm8750",
"wm,wm8850",
+ NULL
};
DT_MACHINE_START(WMT_DT, "VIA/Wondermedia SoC (Device Tree Support)")
obj-$(CONFIG_ALIGNMENT_TRAP) += alignment.o
obj-$(CONFIG_HIGHMEM) += highmem.o
+obj-$(CONFIG_HUGETLB_PAGE) += hugetlbpage.o
obj-$(CONFIG_CPU_ABRT_NOMMU) += abort-nommu.o
obj-$(CONFIG_CPU_ABRT_EV4) += abort-ev4.o
#ifdef CONFIG_MMU
#ifdef CONFIG_HUGETLB_PAGE
-#error ARM Coherent DMA allocator does not (yet) support huge TLB
+#warning ARM Coherent DMA allocator does not (yet) support huge TLB
#endif
static void *__alloc_from_contiguous(struct device *dev, size_t size,
#include <asm/highmem.h>
#include <asm/smp_plat.h>
#include <asm/tlbflush.h>
+#include <linux/hugetlb.h>
#include "mm.h"
* coherent with the kernels mapping.
*/
if (!PageHighMem(page)) {
- __cpuc_flush_dcache_area(page_address(page), PAGE_SIZE);
+ size_t page_size = PAGE_SIZE << compound_order(page);
+ __cpuc_flush_dcache_area(page_address(page), page_size);
} else {
- void *addr;
-
+ unsigned long i;
if (cache_is_vipt_nonaliasing()) {
- addr = kmap_atomic(page);
- __cpuc_flush_dcache_area(addr, PAGE_SIZE);
- kunmap_atomic(addr);
- } else {
- addr = kmap_high_get(page);
- if (addr) {
+ for (i = 0; i < (1 << compound_order(page)); i++) {
+ void *addr = kmap_atomic(page);
__cpuc_flush_dcache_area(addr, PAGE_SIZE);
- kunmap_high(page);
+ kunmap_atomic(addr);
+ }
+ } else {
+ for (i = 0; i < (1 << compound_order(page)); i++) {
+ void *addr = kmap_high_get(page);
+ if (addr) {
+ __cpuc_flush_dcache_area(addr, PAGE_SIZE);
+ kunmap_high(page);
+ }
}
}
}
{ do_page_fault, SIGSEGV, SEGV_MAPERR, "level 3 translation fault" },
{ do_bad, SIGBUS, 0, "reserved access flag fault" },
{ do_bad, SIGSEGV, SEGV_ACCERR, "level 1 access flag fault" },
- { do_bad, SIGSEGV, SEGV_ACCERR, "level 2 access flag fault" },
+ { do_page_fault, SIGSEGV, SEGV_ACCERR, "level 2 access flag fault" },
{ do_page_fault, SIGSEGV, SEGV_ACCERR, "level 3 access flag fault" },
{ do_bad, SIGBUS, 0, "reserved permission fault" },
{ do_bad, SIGSEGV, SEGV_ACCERR, "level 1 permission fault" },
- { do_sect_fault, SIGSEGV, SEGV_ACCERR, "level 2 permission fault" },
+ { do_page_fault, SIGSEGV, SEGV_ACCERR, "level 2 permission fault" },
{ do_page_fault, SIGSEGV, SEGV_ACCERR, "level 3 permission fault" },
{ do_bad, SIGBUS, 0, "synchronous external abort" },
{ do_bad, SIGBUS, 0, "asynchronous external abort" },
--- /dev/null
+/*
+ * arch/arm/mm/hugetlbpage.c
+ *
+ * Copyright (C) 2012 ARM Ltd.
+ *
+ * Based on arch/x86/include/asm/hugetlb.h and Bill Carson's patches
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/init.h>
+#include <linux/fs.h>
+#include <linux/mm.h>
+#include <linux/hugetlb.h>
+#include <linux/pagemap.h>
+#include <linux/err.h>
+#include <linux/sysctl.h>
+#include <asm/mman.h>
+#include <asm/tlb.h>
+#include <asm/tlbflush.h>
+#include <asm/pgalloc.h>
+
+/*
+ * On ARM, huge pages are backed by pmd's rather than pte's, so we do a lot
+ * of type casting from pmd_t * to pte_t *.
+ */
+
+pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr)
+{
+ pgd_t *pgd;
+ pud_t *pud;
+ pmd_t *pmd = NULL;
+
+ pgd = pgd_offset(mm, addr);
+ if (pgd_present(*pgd)) {
+ pud = pud_offset(pgd, addr);
+ if (pud_present(*pud))
+ pmd = pmd_offset(pud, addr);
+ }
+
+ return (pte_t *)pmd;
+}
+
+struct page *follow_huge_addr(struct mm_struct *mm, unsigned long address,
+ int write)
+{
+ return ERR_PTR(-EINVAL);
+}
+
+int pud_huge(pud_t pud)
+{
+ return 0;
+}
+
+int huge_pmd_unshare(struct mm_struct *mm, unsigned long *addr, pte_t *ptep)
+{
+ return 0;
+}
+
+pte_t *huge_pte_alloc(struct mm_struct *mm,
+ unsigned long addr, unsigned long sz)
+{
+ pgd_t *pgd;
+ pud_t *pud;
+ pte_t *pte = NULL;
+
+ pgd = pgd_offset(mm, addr);
+ pud = pud_alloc(mm, pgd, addr);
+ if (pud)
+ pte = (pte_t *)pmd_alloc(mm, pud, addr);
+
+ return pte;
+}
+
+struct page *
+follow_huge_pmd(struct mm_struct *mm, unsigned long address,
+ pmd_t *pmd, int write)
+{
+ struct page *page;
+
+ page = pte_page(*(pte_t *)pmd);
+ if (page)
+ page += ((address & ~PMD_MASK) >> PAGE_SHIFT);
+ return page;
+}
+
+int pmd_huge(pmd_t pmd)
+{
+ return pmd_val(pmd) && !(pmd_val(pmd) & PMD_TABLE_BIT);
+}
static struct platform_device orion_ge10_shared = {
.name = MV643XX_ETH_SHARED_NAME,
- .id = 1,
+ .id = 2,
.dev = {
.platform_data = &orion_ge10_shared_data,
},
static struct platform_device orion_ge10 = {
.name = MV643XX_ETH_NAME,
- .id = 1,
- .num_resources = 2,
+ .id = 2,
+ .num_resources = 1,
.resource = orion_ge10_resources,
.dev = {
.coherent_dma_mask = DMA_BIT_MASK(32),
static struct platform_device orion_ge11_shared = {
.name = MV643XX_ETH_SHARED_NAME,
- .id = 1,
+ .id = 3,
.dev = {
.platform_data = &orion_ge11_shared_data,
},
static struct platform_device orion_ge11 = {
.name = MV643XX_ETH_NAME,
- .id = 1,
- .num_resources = 2,
+ .id = 3,
+ .num_resources = 1,
.resource = orion_ge11_resources,
.dev = {
.coherent_dma_mask = DMA_BIT_MASK(32),
#ifndef __PLAT_COMMON_H
#include <linux/mv643xx_eth.h>
+#include <linux/platform_data/usb-ehci-orion.h>
struct dsa_platform_data;
struct mv_sata_platform_data;
str r11, [r10, #TI_PREEMPT]
#endif
ldr r0, VFP_arch_address
- str r5, [r0] @ known non-zero value
+ str r0, [r0] @ set to non-zero value
mov pc, r9 @ we have handled the fault
ENDPROC(vfp_testing_entry)
config ARCH_SPARSEMEM_ENABLE
def_bool n
+config NODES_SHIFT
+ int
+ default "2"
+ depends on NEED_MULTIPLE_NODES
+
source "mm/Kconfig"
config OWNERSHIP_TRACE
generic-y += clkdev.h
generic-y += exec.h
generic-y += trace_clock.h
+generic-y += param.h
+++ /dev/null
-#ifndef __ASM_AVR32_NUMNODES_H
-#define __ASM_AVR32_NUMNODES_H
-
-/* Max 4 nodes */
-#define NODES_SHIFT 2
-
-#endif /* __ASM_AVR32_NUMNODES_H */
+++ /dev/null
-#ifndef __ASM_AVR32_PARAM_H
-#define __ASM_AVR32_PARAM_H
-
-#include <uapi/asm/param.h>
-
-# define HZ CONFIG_HZ
-# define USER_HZ 100 /* User interfaces are in "ticks" */
-# define CLOCKS_PER_SEC (USER_HZ) /* frequency at which times() counts */
-#endif /* __ASM_AVR32_PARAM_H */
header-y += termios.h
header-y += types.h
header-y += unistd.h
+generic-y += param.h
+++ /dev/null
-#ifndef _UAPI__ASM_AVR32_PARAM_H
-#define _UAPI__ASM_AVR32_PARAM_H
-
-
-#ifndef HZ
-# define HZ 100
-#endif
-
-/* TODO: Should be configurable */
-#define EXEC_PAGESIZE 4096
-
-#ifndef NOGROUP
-# define NOGROUP (-1)
-#endif
-
-#define MAXHOSTNAMELEN 64
-
-#endif /* _UAPI__ASM_AVR32_PARAM_H */
break;
case R_AVR32_GOT18SW:
if ((relocation & 0xfffe0003) != 0
- && (relocation & 0xfffc0003) != 0xffff0000)
+ && (relocation & 0xfffc0000) != 0xfffc0000)
return reloc_overflow(module, "R_AVR32_GOT18SW",
relocation);
relocation >>= 2;
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <asm/bootinfo.h>
+#include <asm/idle.h>
#include <asm/reboot.h>
#include <asm/mach-au1x00/au1000.h>
#include <prom.h>
#include <linux/interrupt.h>
#include <linux/spinlock.h>
+#include <asm/idle.h>
#include <asm/processor.h>
#include <asm/time.h>
#include <asm/mach-au1x00/au1000.h>
#include <linux/clk.h>
#include <asm/bootinfo.h>
+#include <asm/idle.h>
#include <asm/time.h> /* for mips_hpt_frequency */
#include <asm/reboot.h> /* for _machine_{restart,halt} */
#include <asm/mips_machine.h>
#include <linux/io.h>
#include <linux/leds.h>
+#include <asm/idle.h>
#include <asm/processor.h>
#include <cobalt.h>
CONFIG_USB_HID=y
CONFIG_USB_SUPPORT=y
CONFIG_USB=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_HIDDEV=y
CONFIG_USB=y
CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PLATFORM=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_DYNAMIC_MINORS=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_OTG_WHITELIST=y
CONFIG_USB_MON=y
CONFIG_USB_EHCI_HCD=y
#include <linux/seq_file.h>
#include <linux/clk.h>
-extern void (*cpu_wait) (void);
-
struct clk;
struct clk_ops {
--- /dev/null
+#ifndef __ASM_IDLE_H
+#define __ASM_IDLE_H
+
+#include <linux/linkage.h>
+
+extern void (*cpu_wait)(void);
+extern void r4k_wait(void);
+extern asmlinkage void __r4k_wait(void);
+extern void r4k_wait_irqoff(void);
+extern void __pastwait(void);
+
+static inline int using_rollback_handler(void)
+{
+ return cpu_wait == r4k_wait;
+}
+
+static inline int address_is_in_r4k_wait_irqoff(unsigned long addr)
+{
+ return addr >= (unsigned long)r4k_wait_irqoff &&
+ addr < (unsigned long)__pastwait;
+}
+
+#endif /* __ASM_IDLE_H */
+++ /dev/null
-/*
-* This file is subject to the terms and conditions of the GNU General Public
-* License. See the file "COPYING" in the main directory of this archive
-* for more details.
-*
-* Copyright (C) 2012 MIPS Technologies, Inc. All rights reserved.
-* Authors: Sanjay Lal <sanjayl@kymasys.com>
-*/
-
-#ifndef __LINUX_KVM_MIPS_H
-#define __LINUX_KVM_MIPS_H
-
-#include <linux/types.h>
-
-#define __KVM_MIPS
-
-#define N_MIPS_COPROC_REGS 32
-#define N_MIPS_COPROC_SEL 8
-
-/* for KVM_GET_REGS and KVM_SET_REGS */
-struct kvm_regs {
- __u32 gprs[32];
- __u32 hi;
- __u32 lo;
- __u32 pc;
-
- __u32 cp0reg[N_MIPS_COPROC_REGS][N_MIPS_COPROC_SEL];
-};
-
-/* for KVM_GET_SREGS and KVM_SET_SREGS */
-struct kvm_sregs {
-};
-
-/* for KVM_GET_FPU and KVM_SET_FPU */
-struct kvm_fpu {
-};
-
-struct kvm_debug_exit_arch {
-};
-
-/* for KVM_SET_GUEST_DEBUG */
-struct kvm_guest_debug_arch {
-};
-
-struct kvm_mips_interrupt {
- /* in */
- __u32 cpu;
- __u32 irq;
-};
-
-/* definition of registers in kvm_run */
-struct kvm_sync_regs {
-};
-
-#endif /* __LINUX_KVM_MIPS_H */
#ifdef CONFIG_FLATMEM
-#define pfn_valid(pfn) \
-({ \
- unsigned long __pfn = (pfn); \
- /* avoid <linux/bootmem.h> include hell */ \
- extern unsigned long min_low_pfn; \
- \
- __pfn >= min_low_pfn && __pfn < max_mapnr; \
-})
+static inline int pfn_valid(unsigned long pfn)
+{
+ /* avoid <linux/mm.h> include hell */
+ extern unsigned long max_mapnr;
+
+ return pfn >= ARCH_PFN_OFFSET && pfn < max_mapnr;
+}
#elif defined(CONFIG_SPARSEMEM)
/*
* System setup and hardware flags..
*/
-extern void (*cpu_wait)(void);
extern unsigned int vced_count, vcei_count;
--- /dev/null
+/*
+* This file is subject to the terms and conditions of the GNU General Public
+* License. See the file "COPYING" in the main directory of this archive
+* for more details.
+*
+* Copyright (C) 2012 MIPS Technologies, Inc. All rights reserved.
+* Authors: Sanjay Lal <sanjayl@kymasys.com>
+*/
+
+#ifndef __LINUX_KVM_MIPS_H
+#define __LINUX_KVM_MIPS_H
+
+#include <linux/types.h>
+
+#define __KVM_MIPS
+
+#define N_MIPS_COPROC_REGS 32
+#define N_MIPS_COPROC_SEL 8
+
+/* for KVM_GET_REGS and KVM_SET_REGS */
+struct kvm_regs {
+ __u32 gprs[32];
+ __u32 hi;
+ __u32 lo;
+ __u32 pc;
+
+ __u32 cp0reg[N_MIPS_COPROC_REGS][N_MIPS_COPROC_SEL];
+};
+
+/* for KVM_GET_SREGS and KVM_SET_SREGS */
+struct kvm_sregs {
+};
+
+/* for KVM_GET_FPU and KVM_SET_FPU */
+struct kvm_fpu {
+};
+
+struct kvm_debug_exit_arch {
+};
+
+/* for KVM_SET_GUEST_DEBUG */
+struct kvm_guest_debug_arch {
+};
+
+struct kvm_mips_interrupt {
+ /* in */
+ __u32 cpu;
+ __u32 irq;
+};
+
+/* definition of registers in kvm_run */
+struct kvm_sync_regs {
+};
+
+#endif /* __LINUX_KVM_MIPS_H */
#define __NR_process_vm_writev (__NR_Linux + 305)
#define __NR_kcmp (__NR_Linux + 306)
#define __NR_finit_module (__NR_Linux + 307)
+#define __NR_getdents64 (__NR_Linux + 308)
/*
* Offset of the last Linux 64-bit flavoured syscall
*/
-#define __NR_Linux_syscalls 307
+#define __NR_Linux_syscalls 308
#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
#define __NR_64_Linux 5000
-#define __NR_64_Linux_syscalls 307
+#define __NR_64_Linux_syscalls 308
#if _MIPS_SIM == _MIPS_SIM_NABI32
extra-y := head.o vmlinux.lds
-obj-y += cpu-probe.o branch.o entry.o genex.o irq.o process.o \
+obj-y += cpu-probe.o branch.o entry.o genex.o idle.o irq.o process.o \
prom.o ptrace.o reset.o setup.o signal.o syscall.o \
time.o topology.o traps.o unaligned.o watch.o vdso.o
#include <asm/spram.h>
#include <asm/uaccess.h>
-/*
- * Not all of the MIPS CPUs have the "wait" instruction available. Moreover,
- * the implementation of the "wait" feature differs between CPU families. This
- * points to the function that implements CPU specific wait.
- * The wait instruction stops the pipeline and reduces the power consumption of
- * the CPU very much.
- */
-void (*cpu_wait)(void);
-EXPORT_SYMBOL(cpu_wait);
-
-static void r3081_wait(void)
-{
- unsigned long cfg = read_c0_conf();
- write_c0_conf(cfg | R30XX_CONF_HALT);
-}
-
-static void r39xx_wait(void)
-{
- local_irq_disable();
- if (!need_resched())
- write_c0_conf(read_c0_conf() | TX39_CONF_HALT);
- local_irq_enable();
-}
-
-extern void r4k_wait(void);
-
-/*
- * This variant is preferable as it allows testing need_resched and going to
- * sleep depending on the outcome atomically. Unfortunately the "It is
- * implementation-dependent whether the pipeline restarts when a non-enabled
- * interrupt is requested" restriction in the MIPS32/MIPS64 architecture makes
- * using this version a gamble.
- */
-void r4k_wait_irqoff(void)
-{
- local_irq_disable();
- if (!need_resched())
- __asm__(" .set push \n"
- " .set mips3 \n"
- " wait \n"
- " .set pop \n");
- local_irq_enable();
- __asm__(" .globl __pastwait \n"
- "__pastwait: \n");
-}
-
-/*
- * The RM7000 variant has to handle erratum 38. The workaround is to not
- * have any pending stores when the WAIT instruction is executed.
- */
-static void rm7k_wait_irqoff(void)
-{
- local_irq_disable();
- if (!need_resched())
- __asm__(
- " .set push \n"
- " .set mips3 \n"
- " .set noat \n"
- " mfc0 $1, $12 \n"
- " sync \n"
- " mtc0 $1, $12 # stalls until W stage \n"
- " wait \n"
- " mtc0 $1, $12 # stalls until W stage \n"
- " .set pop \n");
- local_irq_enable();
-}
-
-/*
- * The Au1xxx wait is available only if using 32khz counter or
- * external timer source, but specifically not CP0 Counter.
- * alchemy/common/time.c may override cpu_wait!
- */
-static void au1k_wait(void)
-{
- __asm__(" .set mips3 \n"
- " cache 0x14, 0(%0) \n"
- " cache 0x14, 32(%0) \n"
- " sync \n"
- " nop \n"
- " wait \n"
- " nop \n"
- " nop \n"
- " nop \n"
- " nop \n"
- " .set mips0 \n"
- : : "r" (au1k_wait));
-}
-
-static int __initdata nowait;
-
-static int __init wait_disable(char *s)
-{
- nowait = 1;
-
- return 1;
-}
-
-__setup("nowait", wait_disable);
-
static int __cpuinitdata mips_fpu_disabled;
static int __init fpu_disable(char *s)
__setup("nodsp", dsp_disable);
-void __init check_wait(void)
-{
- struct cpuinfo_mips *c = ¤t_cpu_data;
-
- if (nowait) {
- printk("Wait instruction disabled.\n");
- return;
- }
-
- switch (c->cputype) {
- case CPU_R3081:
- case CPU_R3081E:
- cpu_wait = r3081_wait;
- break;
- case CPU_TX3927:
- cpu_wait = r39xx_wait;
- break;
- case CPU_R4200:
-/* case CPU_R4300: */
- case CPU_R4600:
- case CPU_R4640:
- case CPU_R4650:
- case CPU_R4700:
- case CPU_R5000:
- case CPU_R5500:
- case CPU_NEVADA:
- case CPU_4KC:
- case CPU_4KEC:
- case CPU_4KSC:
- case CPU_5KC:
- case CPU_25KF:
- case CPU_PR4450:
- case CPU_BMIPS3300:
- case CPU_BMIPS4350:
- case CPU_BMIPS4380:
- case CPU_BMIPS5000:
- case CPU_CAVIUM_OCTEON:
- case CPU_CAVIUM_OCTEON_PLUS:
- case CPU_CAVIUM_OCTEON2:
- case CPU_JZRISC:
- case CPU_LOONGSON1:
- case CPU_XLR:
- case CPU_XLP:
- cpu_wait = r4k_wait;
- break;
-
- case CPU_RM7000:
- cpu_wait = rm7k_wait_irqoff;
- break;
-
- case CPU_M14KC:
- case CPU_M14KEC:
- case CPU_24K:
- case CPU_34K:
- case CPU_1004K:
- cpu_wait = r4k_wait;
- if (read_c0_config7() & MIPS_CONF7_WII)
- cpu_wait = r4k_wait_irqoff;
- break;
-
- case CPU_74K:
- cpu_wait = r4k_wait;
- if ((c->processor_id & 0xff) >= PRID_REV_ENCODE_332(2, 1, 0))
- cpu_wait = r4k_wait_irqoff;
- break;
-
- case CPU_TX49XX:
- cpu_wait = r4k_wait_irqoff;
- break;
- case CPU_ALCHEMY:
- cpu_wait = au1k_wait;
- break;
- case CPU_20KC:
- /*
- * WAIT on Rev1.0 has E1, E2, E3 and E16.
- * WAIT on Rev2.0 and Rev3.0 has E16.
- * Rev3.1 WAIT is nop, why bother
- */
- if ((c->processor_id & 0xff) <= 0x64)
- break;
-
- /*
- * Another rev is incremeting c0_count at a reduced clock
- * rate while in WAIT mode. So we basically have the choice
- * between using the cp0 timer as clocksource or avoiding
- * the WAIT instruction. Until more details are known,
- * disable the use of WAIT for 20Kc entirely.
- cpu_wait = r4k_wait;
- */
- break;
- case CPU_RM9000:
- if ((c->processor_id & 0x00ff) >= 0x40)
- cpu_wait = r4k_wait;
- break;
- default:
- break;
- }
-}
-
static inline void check_errata(void)
{
struct cpuinfo_mips *c = ¤t_cpu_data;
__FINIT
.align 5 /* 32 byte rollback region */
-LEAF(r4k_wait)
+LEAF(__r4k_wait)
.set push
.set noreorder
/* start of rollback region */
jr ra
nop
.set pop
- END(r4k_wait)
+ END(__r4k_wait)
.macro BUILD_ROLLBACK_PROLOGUE handler
FEXPORT(rollback_\handler)
.set push
.set noat
MFC0 k0, CP0_EPC
- PTR_LA k1, r4k_wait
+ PTR_LA k1, __r4k_wait
ori k0, 0x1f /* 32 byte rollback region */
xori k0, 0x1f
bne k0, k1, 9f
--- /dev/null
+/*
+ * MIPS idle loop and WAIT instruction support.
+ *
+ * Copyright (C) xxxx the Anonymous
+ * Copyright (C) 1994 - 2006 Ralf Baechle
+ * Copyright (C) 2003, 2004 Maciej W. Rozycki
+ * Copyright (C) 2001, 2004, 2011, 2012 MIPS Technologies, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/irqflags.h>
+#include <linux/printk.h>
+#include <linux/sched.h>
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/idle.h>
+#include <asm/mipsregs.h>
+
+/*
+ * Not all of the MIPS CPUs have the "wait" instruction available. Moreover,
+ * the implementation of the "wait" feature differs between CPU families. This
+ * points to the function that implements CPU specific wait.
+ * The wait instruction stops the pipeline and reduces the power consumption of
+ * the CPU very much.
+ */
+void (*cpu_wait)(void);
+EXPORT_SYMBOL(cpu_wait);
+
+static void r3081_wait(void)
+{
+ unsigned long cfg = read_c0_conf();
+ write_c0_conf(cfg | R30XX_CONF_HALT);
+ local_irq_enable();
+}
+
+static void r39xx_wait(void)
+{
+ if (!need_resched())
+ write_c0_conf(read_c0_conf() | TX39_CONF_HALT);
+ local_irq_enable();
+}
+
+void r4k_wait(void)
+{
+ local_irq_enable();
+ __r4k_wait();
+}
+
+/*
+ * This variant is preferable as it allows testing need_resched and going to
+ * sleep depending on the outcome atomically. Unfortunately the "It is
+ * implementation-dependent whether the pipeline restarts when a non-enabled
+ * interrupt is requested" restriction in the MIPS32/MIPS64 architecture makes
+ * using this version a gamble.
+ */
+void r4k_wait_irqoff(void)
+{
+ if (!need_resched())
+ __asm__(
+ " .set push \n"
+ " .set mips3 \n"
+ " wait \n"
+ " .set pop \n");
+ local_irq_enable();
+ __asm__(
+ " .globl __pastwait \n"
+ "__pastwait: \n");
+}
+
+/*
+ * The RM7000 variant has to handle erratum 38. The workaround is to not
+ * have any pending stores when the WAIT instruction is executed.
+ */
+static void rm7k_wait_irqoff(void)
+{
+ if (!need_resched())
+ __asm__(
+ " .set push \n"
+ " .set mips3 \n"
+ " .set noat \n"
+ " mfc0 $1, $12 \n"
+ " sync \n"
+ " mtc0 $1, $12 # stalls until W stage \n"
+ " wait \n"
+ " mtc0 $1, $12 # stalls until W stage \n"
+ " .set pop \n");
+ local_irq_enable();
+}
+
+/*
+ * The Au1xxx wait is available only if using 32khz counter or
+ * external timer source, but specifically not CP0 Counter.
+ * alchemy/common/time.c may override cpu_wait!
+ */
+static void au1k_wait(void)
+{
+ __asm__(
+ " .set mips3 \n"
+ " cache 0x14, 0(%0) \n"
+ " cache 0x14, 32(%0) \n"
+ " sync \n"
+ " nop \n"
+ " wait \n"
+ " nop \n"
+ " nop \n"
+ " nop \n"
+ " nop \n"
+ " .set mips0 \n"
+ : : "r" (au1k_wait));
+ local_irq_enable();
+}
+
+static int __initdata nowait;
+
+static int __init wait_disable(char *s)
+{
+ nowait = 1;
+
+ return 1;
+}
+
+__setup("nowait", wait_disable);
+
+void __init check_wait(void)
+{
+ struct cpuinfo_mips *c = ¤t_cpu_data;
+
+ if (nowait) {
+ printk("Wait instruction disabled.\n");
+ return;
+ }
+
+ switch (c->cputype) {
+ case CPU_R3081:
+ case CPU_R3081E:
+ cpu_wait = r3081_wait;
+ break;
+ case CPU_TX3927:
+ cpu_wait = r39xx_wait;
+ break;
+ case CPU_R4200:
+/* case CPU_R4300: */
+ case CPU_R4600:
+ case CPU_R4640:
+ case CPU_R4650:
+ case CPU_R4700:
+ case CPU_R5000:
+ case CPU_R5500:
+ case CPU_NEVADA:
+ case CPU_4KC:
+ case CPU_4KEC:
+ case CPU_4KSC:
+ case CPU_5KC:
+ case CPU_25KF:
+ case CPU_PR4450:
+ case CPU_BMIPS3300:
+ case CPU_BMIPS4350:
+ case CPU_BMIPS4380:
+ case CPU_BMIPS5000:
+ case CPU_CAVIUM_OCTEON:
+ case CPU_CAVIUM_OCTEON_PLUS:
+ case CPU_CAVIUM_OCTEON2:
+ case CPU_JZRISC:
+ case CPU_LOONGSON1:
+ case CPU_XLR:
+ case CPU_XLP:
+ cpu_wait = r4k_wait;
+ break;
+
+ case CPU_RM7000:
+ cpu_wait = rm7k_wait_irqoff;
+ break;
+
+ case CPU_M14KC:
+ case CPU_M14KEC:
+ case CPU_24K:
+ case CPU_34K:
+ case CPU_1004K:
+ cpu_wait = r4k_wait;
+ if (read_c0_config7() & MIPS_CONF7_WII)
+ cpu_wait = r4k_wait_irqoff;
+ break;
+
+ case CPU_74K:
+ cpu_wait = r4k_wait;
+ if ((c->processor_id & 0xff) >= PRID_REV_ENCODE_332(2, 1, 0))
+ cpu_wait = r4k_wait_irqoff;
+ break;
+
+ case CPU_TX49XX:
+ cpu_wait = r4k_wait_irqoff;
+ break;
+ case CPU_ALCHEMY:
+ cpu_wait = au1k_wait;
+ break;
+ case CPU_20KC:
+ /*
+ * WAIT on Rev1.0 has E1, E2, E3 and E16.
+ * WAIT on Rev2.0 and Rev3.0 has E16.
+ * Rev3.1 WAIT is nop, why bother
+ */
+ if ((c->processor_id & 0xff) <= 0x64)
+ break;
+
+ /*
+ * Another rev is incremeting c0_count at a reduced clock
+ * rate while in WAIT mode. So we basically have the choice
+ * between using the cp0 timer as clocksource or avoiding
+ * the WAIT instruction. Until more details are known,
+ * disable the use of WAIT for 20Kc entirely.
+ cpu_wait = r4k_wait;
+ */
+ break;
+ case CPU_RM9000:
+ if ((c->processor_id & 0x00ff) >= 0x40)
+ cpu_wait = r4k_wait;
+ break;
+ default:
+ break;
+ }
+}
+
+static void smtc_idle_hook(void)
+{
+#ifdef CONFIG_MIPS_MT_SMTC
+ void smtc_idle_loop_hook(void);
+
+ smtc_idle_loop_hook();
+#endif
+}
+
+void arch_cpu_idle(void)
+{
+ smtc_idle_hook();
+ if (cpu_wait)
+ cpu_wait();
+ else
+ local_irq_enable();
+}
void __kprobes arch_remove_kprobe(struct kprobe *p)
{
- free_insn_slot(p->ainsn.insn, 0);
+ if (p->ainsn.insn) {
+ free_insn_slot(p->ainsn.insn, 0);
+ p->ainsn.insn = NULL;
+ }
}
static void save_previous_kprobe(struct kprobe_ctlblk *kcb)
#include <asm/bootinfo.h>
#include <asm/cpu.h>
#include <asm/cpu-features.h>
+#include <asm/idle.h>
#include <asm/mipsregs.h>
#include <asm/processor.h>
#include <asm/prom.h>
}
#endif
-void arch_cpu_idle(void)
-{
-#ifdef CONFIG_MIPS_MT_SMTC
- extern void smtc_idle_loop_hook(void);
-
- smtc_idle_loop_hook();
-#endif
- if (cpu_wait)
- (*cpu_wait)();
- else
- local_irq_enable();
-}
-
asmlinkage void ret_from_fork(void);
asmlinkage void ret_from_kernel_thread(void);
PTR sys_process_vm_writev /* 5305 */
PTR sys_kcmp
PTR sys_finit_module
+ PTR sys_getdents64
.size sys_call_table,.-sys_call_table
#include <linux/atomic.h>
#include <asm/cpu.h>
#include <asm/processor.h>
+#include <asm/idle.h>
#include <asm/r4k-timer.h>
#include <asm/mmu_context.h>
#include <asm/time.h>
#include <asm/hardirq.h>
#include <asm/hazards.h>
#include <asm/irq.h>
+#include <asm/idle.h>
#include <asm/mmu_context.h>
#include <asm/mipsregs.h>
#include <asm/cacheflush.h>
unsigned long flags;
int mtflags;
unsigned long tcrestart;
- extern void r4k_wait_irqoff(void), __pastwait(void);
int set_resched_flag = (type == LINUX_SMP_IPI &&
action == SMP_RESCHEDULE_YOURSELF);
*/
if (cpu_wait == r4k_wait_irqoff) {
tcrestart = read_tc_c0_tcrestart();
- if (tcrestart >= (unsigned long)r4k_wait_irqoff
- && tcrestart < (unsigned long)__pastwait) {
+ if (address_is_in_r4k_wait_irqoff(tcrestart)) {
write_tc_c0_tcrestart(__pastwait);
tcstatus &= ~TCSTATUS_IXMT;
write_tc_c0_tcstatus(tcstatus);
#include <asm/dsp.h>
#include <asm/fpu.h>
#include <asm/fpu_emulator.h>
+#include <asm/idle.h>
#include <asm/mipsregs.h>
#include <asm/mipsmtregs.h>
#include <asm/module.h>
#include <asm/uasm.h>
extern void check_wait(void);
-extern asmlinkage void r4k_wait(void);
extern asmlinkage void rollback_handle_int(void);
extern asmlinkage void handle_int(void);
extern u32 handle_tlbl[];
extern char except_vec_vi, except_vec_vi_lui;
extern char except_vec_vi_ori, except_vec_vi_end;
extern char rollback_except_vec_vi;
- char *vec_start = (cpu_wait == r4k_wait) ?
+ char *vec_start = using_rollback_handler() ?
&rollback_except_vec_vi : &except_vec_vi;
#ifdef CONFIG_MIPS_MT_SMTC
/*
extern char except_vec4;
extern char except_vec3_r4000;
unsigned long i;
- int rollback;
check_wait();
- rollback = (cpu_wait == r4k_wait);
#if defined(CONFIG_KGDB)
if (kgdb_early_setup)
if (board_be_init)
board_be_init();
- set_except_vector(0, rollback ? rollback_handle_int : handle_int);
+ set_except_vector(0, using_rollback_handler() ? rollback_handle_int
+ : handle_int);
set_except_vector(1, handle_tlbm);
set_except_vector(2, handle_tlbl);
set_except_vector(3, handle_tlbs);
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/kvm_host.h>
+#include <linux/srcu.h>
+
#include <asm/cpu.h>
#include <asm/bootinfo.h>
}
}
-static void kvm_mips_map_page(struct kvm *kvm, gfn_t gfn)
+static int kvm_mips_map_page(struct kvm *kvm, gfn_t gfn)
{
+ int srcu_idx, err = 0;
pfn_t pfn;
if (kvm->arch.guest_pmap[gfn] != KVM_INVALID_PAGE)
- return;
+ return 0;
+ srcu_idx = srcu_read_lock(&kvm->srcu);
pfn = kvm_mips_gfn_to_pfn(kvm, gfn);
if (kvm_mips_is_error_pfn(pfn)) {
- panic("Couldn't get pfn for gfn %#" PRIx64 "!\n", gfn);
+ kvm_err("Couldn't get pfn for gfn %#" PRIx64 "!\n", gfn);
+ err = -EFAULT;
+ goto out;
}
kvm->arch.guest_pmap[gfn] = pfn;
- return;
+out:
+ srcu_read_unlock(&kvm->srcu, srcu_idx);
+ return err;
}
/* Translate guest KSEG0 addresses to Host PA */
gva);
return KVM_INVALID_PAGE;
}
- kvm_mips_map_page(vcpu->kvm, gfn);
+
+ if (kvm_mips_map_page(vcpu->kvm, gfn) < 0)
+ return KVM_INVALID_ADDR;
+
return (kvm->arch.guest_pmap[gfn] << PAGE_SHIFT) + offset;
}
even = !(gfn & 0x1);
vaddr = badvaddr & (PAGE_MASK << 1);
- kvm_mips_map_page(vcpu->kvm, gfn);
- kvm_mips_map_page(vcpu->kvm, gfn ^ 0x1);
+ if (kvm_mips_map_page(vcpu->kvm, gfn) < 0)
+ return -1;
+
+ if (kvm_mips_map_page(vcpu->kvm, gfn ^ 0x1) < 0)
+ return -1;
if (even) {
pfn0 = kvm->arch.guest_pmap[gfn];
pfn0 = 0;
pfn1 = 0;
} else {
- kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo0) >> PAGE_SHIFT);
- kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo1) >> PAGE_SHIFT);
+ if (kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo0) >> PAGE_SHIFT) < 0)
+ return -1;
+
+ if (kvm_mips_map_page(kvm, mips3_tlbpfn_to_paddr(tlb->tlb_lo1) >> PAGE_SHIFT) < 0)
+ return -1;
pfn0 = kvm->arch.guest_pmap[mips3_tlbpfn_to_paddr(tlb->tlb_lo0) >> PAGE_SHIFT];
pfn1 = kvm->arch.guest_pmap[mips3_tlbpfn_to_paddr(tlb->tlb_lo1) >> PAGE_SHIFT];
#include <linux/init.h>
#include <linux/pm.h>
+#include <asm/idle.h>
#include <asm/reboot.h>
#include <loongson.h>
#include <linux/io.h>
#include <linux/pm.h>
+#include <asm/idle.h>
#include <asm/reboot.h>
#include <loongson1.h>
#include <linux/pm.h>
#include <linux/bootmem.h>
+#include <asm/idle.h>
#include <asm/reboot.h>
#include <asm/time.h>
#include <asm/bootinfo.h>
#include <linux/serial_8250.h>
#include <linux/pm.h>
+#include <asm/idle.h>
#include <asm/reboot.h>
#include <asm/time.h>
#include <asm/bootinfo.h>
#include <asm/bootinfo.h>
#include <asm/cacheflush.h>
+#include <asm/idle.h>
#include <asm/r4kcache.h>
#include <asm/reboot.h>
#include <asm/smp-ops.h>
#include <linux/slab.h>
#include <linux/irq.h>
#include <asm/bootinfo.h>
+#include <asm/idle.h>
#include <asm/time.h>
#include <asm/reboot.h>
#include <asm/r4kcache.h>
#include <asm/cacheflush.h>
#include <asm/cpu.h>
+#include <asm/idle.h>
#include <asm/io.h>
#include <asm/processor.h>
#include <asm/reboot.h>
#include <linux/kernel.h>
#include <asm/cacheflush.h>
+#include <asm/idle.h>
#include <asm/mipsregs.h>
#include <asm/processor.h>
SAVE_SP (%sr4, PT_SR4 (\regs))
SAVE_SP (%sr5, PT_SR5 (\regs))
SAVE_SP (%sr6, PT_SR6 (\regs))
- SAVE_SP (%sr7, PT_SR7 (\regs))
SAVE_CR (%cr17, PT_IASQ0(\regs))
mtctl %r0, %cr17
typedef struct {
unsigned int __softirq_pending;
-#ifdef CONFIG_DEBUG_STACKOVERFLOW
unsigned int kernel_stack_usage;
-#ifdef CONFIG_IRQSTACKS
unsigned int irq_stack_usage;
- unsigned int irq_stack_counter;
-#endif
-#endif
#ifdef CONFIG_SMP
unsigned int irq_resched_count;
unsigned int irq_call_count;
#endif
+ unsigned int irq_unaligned_count;
+ unsigned int irq_fpassist_count;
unsigned int irq_tlb_count;
} ____cacheline_aligned irq_cpustat_t;
#include <asm/ptrace.h>
#include <asm/types.h>
#include <asm/percpu.h>
-
#endif /* __ASSEMBLY__ */
/*
#ifndef __ASSEMBLY__
-/*
- * IRQ STACK - used for irq handler
- */
-#ifdef __KERNEL__
-
-#include <linux/spinlock_types.h>
-
-#define IRQ_STACK_SIZE (4096 << 2) /* 16k irq stack size */
-
-union irq_stack_union {
- unsigned long stack[IRQ_STACK_SIZE/sizeof(unsigned long)];
- raw_spinlock_t lock;
-};
-
-DECLARE_PER_CPU(union irq_stack_union, irq_stack_union);
-
-void call_on_stack(unsigned long p1, void *func, unsigned long new_stack);
-
-#endif /* __KERNEL__ */
-
/*
* Data detected about CPUs at boot time which is the same for all CPU's.
* HP boxes are SMP - ie identical processors.
rsm PSW_SM_I, %r0 /* barrier for "Relied upon Translation */
mtsp %r0, %sr4
mtsp %r0, %sr5
- mfsp %sr7, %r1
- or,= %r0,%r1,%r0 /* Only save sr7 in sr3 if sr7 != 0 */
- mtsp %r1, %sr3
+ mtsp %r0, %sr6
tovirt_r1 %r29
load32 KERNEL_PSW, %r1
rsm PSW_SM_QUIET,%r0 /* second "heavy weight" ctl op */
- mtsp %r0, %sr6
- mtsp %r0, %sr7
mtctl %r0, %cr17 /* Clear IIASQ tail */
mtctl %r0, %cr17 /* Clear IIASQ head */
mtctl %r1, %ipsw
/* we save the registers in the task struct */
+ copy %r30, %r17
mfctl %cr30, %r1
+ ldo THREAD_SZ_ALGN(%r1), %r30
+ mtsp %r0,%sr7
+ mtsp %r16,%sr3
tophys %r1,%r9
LDREG TI_TASK(%r9), %r1 /* thread_info -> task_struct */
tophys %r1,%r9
ldo TASK_REGS(%r9),%r9
- STREG %r30, PT_GR30(%r9)
+ STREG %r17,PT_GR30(%r9)
STREG %r29,PT_GR29(%r9)
STREG %r26,PT_GR26(%r9)
+ STREG %r16,PT_SR7(%r9)
copy %r9,%r29
- mfctl %cr30, %r1
- ldo THREAD_SZ_ALGN(%r1), %r30
.endm
.macro get_stack_use_r30
/* we put a struct pt_regs on the stack and save the registers there */
tophys %r30,%r9
- STREG %r30,PT_GR30(%r9)
+ copy %r30,%r1
ldo PT_SZ_ALGN(%r30),%r30
+ STREG %r1,PT_GR30(%r9)
STREG %r29,PT_GR29(%r9)
STREG %r26,PT_GR26(%r9)
+ STREG %r16,PT_SR7(%r9)
copy %r9,%r29
.endm
{HPHW_NPROC,0x5DD,0x4,0x81,"Duet W2"},
{HPHW_NPROC,0x5DE,0x4,0x81,"Piccolo W+"},
{HPHW_NPROC,0x5DF,0x4,0x81,"Cantata W2"},
+ {HPHW_NPROC,0x5DF,0x0,0x00,"Marcato W+? (rp5470)"},
{HPHW_NPROC,0x5E0,0x4,0x91,"Cantata DC- W2"},
{HPHW_NPROC,0x5E1,0x4,0x91,"Crescendo DC- W2"},
{HPHW_NPROC,0x5E2,0x4,0x91,"Crescendo 650 W2"},
#include <linux/interrupt.h>
#include <linux/kernel_stat.h>
#include <linux/seq_file.h>
-#include <linux/spinlock.h>
#include <linux/types.h>
#include <asm/io.h>
#include <asm/smp.h>
+#include <asm/ldcw.h>
#undef PARISC_IRQ_CR16_COUNTS
for_each_online_cpu(j)
seq_printf(p, "%10u ", irq_stats(j)->irq_stack_usage);
seq_puts(p, " Interrupt stack usage\n");
- seq_printf(p, "%*s: ", prec, "ISC");
- for_each_online_cpu(j)
- seq_printf(p, "%10u ", irq_stats(j)->irq_stack_counter);
- seq_puts(p, " Interrupt stack usage counter\n");
# endif
#endif
#ifdef CONFIG_SMP
seq_printf(p, "%10u ", irq_stats(j)->irq_call_count);
seq_puts(p, " Function call interrupts\n");
#endif
+ seq_printf(p, "%*s: ", prec, "UAH");
+ for_each_online_cpu(j)
+ seq_printf(p, "%10u ", irq_stats(j)->irq_unaligned_count);
+ seq_puts(p, " Unaligned access handler traps\n");
+ seq_printf(p, "%*s: ", prec, "FPA");
+ for_each_online_cpu(j)
+ seq_printf(p, "%10u ", irq_stats(j)->irq_fpassist_count);
+ seq_puts(p, " Floating point assist traps\n");
seq_printf(p, "%*s: ", prec, "TLB");
for_each_online_cpu(j)
seq_printf(p, "%10u ", irq_stats(j)->irq_tlb_count);
return (BITS_PER_LONG - bit) + TIMER_IRQ;
}
+#ifdef CONFIG_IRQSTACKS
+/*
+ * IRQ STACK - used for irq handler
+ */
+#define IRQ_STACK_SIZE (4096 << 2) /* 16k irq stack size */
+
+union irq_stack_union {
+ unsigned long stack[IRQ_STACK_SIZE/sizeof(unsigned long)];
+ volatile unsigned int slock[4];
+ volatile unsigned int lock[1];
+};
+
+DEFINE_PER_CPU(union irq_stack_union, irq_stack_union) = {
+ .slock = { 1,1,1,1 },
+ };
+#endif
+
+
int sysctl_panic_on_stackoverflow = 1;
static inline void stack_overflow_check(struct pt_regs *regs)
}
#ifdef CONFIG_IRQSTACKS
-DEFINE_PER_CPU(union irq_stack_union, irq_stack_union) = {
- .lock = __RAW_SPIN_LOCK_UNLOCKED((irq_stack_union).lock)
- };
+/* in entry.S: */
+void call_on_stack(unsigned long p1, void *func, unsigned long new_stack);
static void execute_on_irq_stack(void *func, unsigned long param1)
{
union irq_stack_union *union_ptr;
unsigned long irq_stack;
- raw_spinlock_t *irq_stack_in_use;
+ volatile unsigned int *irq_stack_in_use;
union_ptr = &per_cpu(irq_stack_union, smp_processor_id());
irq_stack = (unsigned long) &union_ptr->stack;
- irq_stack = ALIGN(irq_stack + sizeof(irq_stack_union.lock),
+ irq_stack = ALIGN(irq_stack + sizeof(irq_stack_union.slock),
64); /* align for stack frame usage */
/* We may be called recursive. If we are already using the irq stack,
* just continue to use it. Use spinlocks to serialize
* the irq stack usage.
*/
- irq_stack_in_use = &union_ptr->lock;
- if (!raw_spin_trylock(irq_stack_in_use)) {
+ irq_stack_in_use = (volatile unsigned int *)__ldcw_align(union_ptr);
+ if (!__ldcw(irq_stack_in_use)) {
void (*direct_call)(unsigned long p1) = func;
/* We are using the IRQ stack already.
/* This is where we switch to the IRQ stack. */
call_on_stack(param1, func, irq_stack);
- __inc_irq_stat(irq_stack_counter);
-
/* free up irq stack usage. */
- do_raw_spin_unlock(irq_stack_in_use);
+ *irq_stack_in_use = 1;
}
asmlinkage void do_softirq(void)
convert_phys_for_tlb_insert20 %r26 /* convert phys addr to tlb insert format */
convert_phys_for_tlb_insert20 %r23 /* convert phys addr to tlb insert format */
depd %r24,63,22, %r28 /* Form aliased virtual address 'to' */
- depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
+ depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
copy %r28, %r29
depdi 1, 41,1, %r29 /* Form aliased virtual address 'from' */
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
extrw,u %r23, 24,25, %r23 /* convert phys addr to tlb insert format */
depw %r24, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
copy %r28, %r29
depwi 1, 9,1, %r29 /* Form aliased virtual address 'from' */
#endif
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
depw %r25, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
#endif
/* Purge any old translation */
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
depw %r25, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
#endif
/* Purge any old translation */
#endif
convert_phys_for_tlb_insert20 %r26 /* convert phys addr to tlb insert format */
depd %r25, 63,22, %r28 /* Form aliased virtual address 'to' */
- depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
+ depdi 0, 63,PAGE_SHIFT, %r28 /* Clear any offset bits */
#else
extrw,u %r26, 24,25, %r26 /* convert phys addr to tlb insert format */
depw %r25, 31,22, %r28 /* Form aliased virtual address 'to' */
- depwi 0, 31,12, %r28 /* Clear any offset bits */
+ depwi 0, 31,PAGE_SHIFT, %r28 /* Clear any offset bits */
#endif
/* Purge any old translation */
case 14:
/* Assist Exception Trap, i.e. floating point exception. */
die_if_kernel("Floating point exception", regs, 0); /* quiet */
+ __inc_irq_stat(irq_fpassist_count);
handle_fpe(regs);
return;
#include <linux/signal.h>
#include <linux/ratelimit.h>
#include <asm/uaccess.h>
+#include <asm/hardirq.h>
/* #define DEBUG_UNALIGNED 1 */
struct siginfo si;
register int flop=0; /* true if this is a flop */
+ __inc_irq_stat(irq_unaligned_count);
+
/* log a message with pacing */
if (user_mode(regs)) {
if (current->thread.flags & PARISC_UAC_SIGBUS) {
CONFIG_USB_HIDDEV=y
CONFIG_USB=m
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=m
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_HCD_PPC_OF is not set
/* Get the pointer to a device_node's pci_dn */
#define PCI_DN(dn) ((struct pci_dn *) (dn)->data)
+extern struct pci_dn *pci_get_pdn(struct pci_dev *pdev);
+
extern void * update_dn_pci_info(struct device_node *dn, void *data);
static inline int pci_device_from_OF_node(struct device_node *np,
unsigned long ebbrr;
unsigned long ebbhr;
unsigned long bescr;
+ unsigned long siar;
+ unsigned long sdar;
+ unsigned long sier;
+ unsigned long mmcr0;
+ unsigned long mmcr2;
+ unsigned long mmcra;
#endif
};
DEFINE(THREAD_BESCR, offsetof(struct thread_struct, bescr));
DEFINE(THREAD_EBBHR, offsetof(struct thread_struct, ebbhr));
DEFINE(THREAD_EBBRR, offsetof(struct thread_struct, ebbrr));
+ DEFINE(THREAD_SIAR, offsetof(struct thread_struct, siar));
+ DEFINE(THREAD_SDAR, offsetof(struct thread_struct, sdar));
+ DEFINE(THREAD_SIER, offsetof(struct thread_struct, sier));
+ DEFINE(THREAD_MMCR0, offsetof(struct thread_struct, mmcr0));
+ DEFINE(THREAD_MMCR2, offsetof(struct thread_struct, mmcr2));
+ DEFINE(THREAD_MMCRA, offsetof(struct thread_struct, mmcra));
#endif
#ifdef CONFIG_PPC_TRANSACTIONAL_MEM
DEFINE(PACATMSCRATCH, offsetof(struct paca_struct, tm_scratch));
blr
__init_TLB:
- /* Clear the TLB */
- li r6,128
+ /*
+ * Clear the TLB using the "IS 3" form of tlbiel instruction
+ * (invalidate by congruence class). P7 has 128 CCs, P8 has 512
+ * so we just always do 512
+ */
+ li r6,512
mtctr r6
li r7,0xc00 /* IS field = 0b11 */
ptesync
std r0, THREAD_EBBHR(r3)
mfspr r0, SPRN_EBBRR
std r0, THREAD_EBBRR(r3)
+
+ /* PMU registers made user read/(write) by EBB */
+ mfspr r0, SPRN_SIAR
+ std r0, THREAD_SIAR(r3)
+ mfspr r0, SPRN_SDAR
+ std r0, THREAD_SDAR(r3)
+ mfspr r0, SPRN_SIER
+ std r0, THREAD_SIER(r3)
+ mfspr r0, SPRN_MMCR0
+ std r0, THREAD_MMCR0(r3)
+ mfspr r0, SPRN_MMCR2
+ std r0, THREAD_MMCR2(r3)
+ mfspr r0, SPRN_MMCRA
+ std r0, THREAD_MMCRA(r3)
END_FTR_SECTION_IFSET(CPU_FTR_ARCH_207S)
#endif
ld r0, THREAD_EBBRR(r4)
mtspr SPRN_EBBRR, r0
+ /* PMU registers made user read/(write) by EBB */
+ ld r0, THREAD_SIAR(r4)
+ mtspr SPRN_SIAR, r0
+ ld r0, THREAD_SDAR(r4)
+ mtspr SPRN_SDAR, r0
+ ld r0, THREAD_SIER(r4)
+ mtspr SPRN_SIER, r0
+ ld r0, THREAD_MMCR0(r4)
+ mtspr SPRN_MMCR0, r0
+ ld r0, THREAD_MMCR2(r4)
+ mtspr SPRN_MMCR2, r0
+ ld r0, THREAD_MMCRA(r4)
+ mtspr SPRN_MMCRA, r0
+
ld r0,THREAD_TAR(r4)
mtspr SPRN_TAR,r0
END_FTR_SECTION_IFSET(CPU_FTR_ARCH_207S)
for (i = 0; i < 3; ++i) {
res = &hose->mem_resources[i];
if (!res->flags) {
- printk(KERN_ERR "PCI: Memory resource 0 not set for "
- "host bridge %s (domain %d)\n",
- hose->dn->full_name, hose->global_number);
+ if (i == 0)
+ printk(KERN_ERR "PCI: Memory resource 0 not set for "
+ "host bridge %s (domain %d)\n",
+ hose->dn->full_name, hose->global_number);
continue;
}
offset = hose->mem_offset[i];
}
EXPORT_SYMBOL(pcibus_to_node);
#endif
+
+static void quirk_radeon_32bit_msi(struct pci_dev *dev)
+{
+ struct pci_dn *pdn = pci_get_pdn(dev);
+
+ if (pdn)
+ pdn->force_32bit_msi = 1;
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x68f2, quirk_radeon_32bit_msi);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0xaa68, quirk_radeon_32bit_msi);
#include <asm/ppc-pci.h>
#include <asm/firmware.h>
+struct pci_dn *pci_get_pdn(struct pci_dev *pdev)
+{
+ struct device_node *dn = pci_device_to_OF_node(pdev);
+ if (!dn)
+ return NULL;
+ return PCI_DN(dn);
+}
+
/*
* Traverse_func that inits the PCI fields of the device node.
* NOTE: this *must* be done before read/write config to the device.
select PPC_ICP_NATIVE
select PPC_P7_NAP
select PPC_PCI_CHOICE if EMBEDDED
+ select EPAPR_BOOT
default y
config POWERNV_MSI
define_pe_printk_level(pe_warn, KERN_WARNING);
define_pe_printk_level(pe_info, KERN_INFO);
-static struct pci_dn *pnv_ioda_get_pdn(struct pci_dev *dev)
-{
- struct device_node *np;
-
- np = pci_device_to_OF_node(dev);
- if (!np)
- return NULL;
- return PCI_DN(np);
-}
-
static int pnv_ioda_alloc_pe(struct pnv_phb *phb)
{
unsigned long pe;
{
struct pci_controller *hose = pci_bus_to_host(dev->bus);
struct pnv_phb *phb = hose->private_data;
- struct pci_dn *pdn = pnv_ioda_get_pdn(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
if (!pdn)
return NULL;
/* Add to all parents PELT-V */
while (parent) {
- struct pci_dn *pdn = pnv_ioda_get_pdn(parent);
+ struct pci_dn *pdn = pci_get_pdn(parent);
if (pdn && pdn->pe_number != IODA_INVALID_PE) {
rc = opal_pci_set_peltv(phb->opal_id, pdn->pe_number,
pe->pe_number, OPAL_ADD_PE_TO_DOMAIN);
{
struct pci_controller *hose = pci_bus_to_host(dev->bus);
struct pnv_phb *phb = hose->private_data;
- struct pci_dn *pdn = pnv_ioda_get_pdn(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
struct pnv_ioda_pe *pe;
int pe_num;
struct pci_dev *dev;
list_for_each_entry(dev, &bus->devices, bus_list) {
- struct pci_dn *pdn = pnv_ioda_get_pdn(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
if (pdn == NULL) {
pr_warn("%s: No device node associated with device !\n",
static void pnv_pci_ioda_dma_dev_setup(struct pnv_phb *phb, struct pci_dev *pdev)
{
- struct pci_dn *pdn = pnv_ioda_get_pdn(pdev);
+ struct pci_dn *pdn = pci_get_pdn(pdev);
struct pnv_ioda_pe *pe;
/*
unsigned int is_64, struct msi_msg *msg)
{
struct pnv_ioda_pe *pe = pnv_ioda_get_pe(dev);
+ struct pci_dn *pdn = pci_get_pdn(dev);
struct irq_data *idata;
struct irq_chip *ichip;
unsigned int xive_num = hwirq - phb->msi_base;
if (pe->mve_number < 0)
return -ENXIO;
+ /* Force 32-bit MSI on some broken devices */
+ if (pdn && pdn->force_32bit_msi)
+ is_64 = 0;
+
/* Assign XIVE to PE */
rc = opal_pci_set_xive_pe(phb->opal_id, pe->pe_number, xive_num);
if (rc) {
if (!phb->initialized)
return 0;
- pdn = pnv_ioda_get_pdn(dev);
+ pdn = pci_get_pdn(dev);
if (!pdn || pdn->pe_number == IODA_INVALID_PE)
return -EINVAL;
{
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
+ struct pci_dn *pdn = pci_get_pdn(pdev);
+
+ if (pdn && pdn->force_32bit_msi && !phb->msi32_support)
+ return -ENODEV;
return (phb && phb->msi_bmp.bitmap) ? 0 : -ENODEV;
}
while (npages--)
*(tcep++) = 0;
- if (tbl->it_type & TCE_PCI_SWINV_CREATE)
+ if (tbl->it_type & TCE_PCI_SWINV_FREE)
pnv_pci_ioda_tce_invalidate(tbl, tces, tcep - 1);
}
#define RTAS_CHANGE_MSIX_FN 4
#define RTAS_CHANGE_32MSI_FN 5
-static struct pci_dn *get_pdn(struct pci_dev *pdev)
-{
- struct device_node *dn;
- struct pci_dn *pdn;
-
- dn = pci_device_to_OF_node(pdev);
- if (!dn) {
- dev_dbg(&pdev->dev, "rtas_msi: No OF device node\n");
- return NULL;
- }
-
- pdn = PCI_DN(dn);
- if (!pdn) {
- dev_dbg(&pdev->dev, "rtas_msi: No PCI DN\n");
- return NULL;
- }
-
- return pdn;
-}
-
/* RTAS Helpers */
static int rtas_change_msi(struct pci_dn *pdn, u32 func, u32 num_irqs)
{
struct pci_dn *pdn;
- pdn = get_pdn(pdev);
+ pdn = pci_get_pdn(pdev);
if (!pdn)
return;
struct pci_dn *pdn;
const u32 *req_msi;
- pdn = get_pdn(pdev);
+ pdn = pci_get_pdn(pdev);
if (!pdn)
return -ENODEV;
return 0;
}
+static void rtas_hack_32bit_msi_gen2(struct pci_dev *pdev)
+{
+ u32 addr_hi, addr_lo;
+
+ /*
+ * We should only get in here for IODA1 configs. This is based on the
+ * fact that we using RTAS for MSIs, we don't have the 32 bit MSI RTAS
+ * support, and we are in a PCIe Gen2 slot.
+ */
+ dev_info(&pdev->dev,
+ "rtas_msi: No 32 bit MSI firmware support, forcing 32 bit MSI\n");
+ pci_read_config_dword(pdev, pdev->msi_cap + PCI_MSI_ADDRESS_HI, &addr_hi);
+ addr_lo = 0xffff0000 | ((addr_hi >> (48 - 32)) << 4);
+ pci_write_config_dword(pdev, pdev->msi_cap + PCI_MSI_ADDRESS_LO, addr_lo);
+ pci_write_config_dword(pdev, pdev->msi_cap + PCI_MSI_ADDRESS_HI, 0);
+}
+
static int rtas_setup_msi_irqs(struct pci_dev *pdev, int nvec_in, int type)
{
struct pci_dn *pdn;
struct msi_desc *entry;
struct msi_msg msg;
int nvec = nvec_in;
+ int use_32bit_msi_hack = 0;
- pdn = get_pdn(pdev);
+ pdn = pci_get_pdn(pdev);
if (!pdn)
return -ENODEV;
*/
again:
if (type == PCI_CAP_ID_MSI) {
- if (pdn->force_32bit_msi)
+ if (pdn->force_32bit_msi) {
rc = rtas_change_msi(pdn, RTAS_CHANGE_32MSI_FN, nvec);
- else
+ if (rc < 0) {
+ /*
+ * We only want to run the 32 bit MSI hack below if
+ * the max bus speed is Gen2 speed
+ */
+ if (pdev->bus->max_bus_speed != PCIE_SPEED_5_0GT)
+ return rc;
+
+ use_32bit_msi_hack = 1;
+ }
+ } else
+ rc = -1;
+
+ if (rc < 0)
rc = rtas_change_msi(pdn, RTAS_CHANGE_MSI_FN, nvec);
- if (rc < 0 && !pdn->force_32bit_msi) {
+ if (rc < 0) {
pr_debug("rtas_msi: trying the old firmware call.\n");
rc = rtas_change_msi(pdn, RTAS_CHANGE_FN, nvec);
}
+
+ if (use_32bit_msi_hack && rc > 0)
+ rtas_hack_32bit_msi_gen2(pdev);
} else
rc = rtas_change_msi(pdn, RTAS_CHANGE_MSIX_FN, nvec);
}
arch_initcall(rtas_msi_init);
-static void quirk_radeon(struct pci_dev *dev)
-{
- struct pci_dn *pdn = get_pdn(dev);
-
- if (pdn)
- pdn->force_32bit_msi = 1;
-}
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x68f2, quirk_radeon);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0xaa68, quirk_radeon);
unsigned long empty_zero_page;
EXPORT_SYMBOL_GPL(empty_zero_page);
-static struct kcore_list kcore_mem, kcore_vmalloc;
-
static void setup_zero_page(void)
{
struct page *page;
*/
static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg)
{
- if (bus == 0 && (devfn == PCI_DEVFN(2, 0)
- || devfn == PCI_DEVFN(0, 0)
- || devfn == PCI_DEVFN(3, 0)))
- return 1;
-
/* This is a workaround for A0 LNC bug where PCI status register does
* not have new CAP bit set. can not be written by SW either.
*
*/
if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE)
return 0;
-
+ if (bus == 0 && (devfn == PCI_DEVFN(2, 0)
+ || devfn == PCI_DEVFN(0, 0)
+ || devfn == PCI_DEVFN(3, 0)))
+ return 1;
return 0; /* langwell on others */
}
# Power management related files
acpi-y += wakeup.o
acpi-y += sleep.o
-acpi-$(CONFIG_PM) += device_pm.o
+acpi-y += device_pm.o
acpi-$(CONFIG_ACPI_SLEEP) += proc.o
acpi-y += ec.o
acpi-$(CONFIG_ACPI_DOCK) += dock.o
acpi-y += pci_root.o pci_link.o pci_irq.o
-acpi-y += csrt.o
acpi-$(CONFIG_X86_INTEL_LPSS) += acpi_lpss.o
acpi-y += acpi_platform.o
acpi-y += power.o
struct lpss_device_desc {
bool clk_required;
- const char *clk_parent;
+ const char *clkdev_name;
bool ltr_required;
unsigned int prv_offset;
};
+static struct lpss_device_desc lpss_dma_desc = {
+ .clk_required = true,
+ .clkdev_name = "hclk",
+};
+
struct lpss_private_data {
void __iomem *mmio_base;
resource_size_t mmio_size;
static struct lpss_device_desc lpt_dev_desc = {
.clk_required = true,
- .clk_parent = "lpss_clk",
.prv_offset = 0x800,
.ltr_required = true,
};
};
static const struct acpi_device_id acpi_lpss_device_ids[] = {
+ /* Generic LPSS devices */
+ { "INTL9C60", (unsigned long)&lpss_dma_desc },
+
/* Lynxpoint LPSS devices */
{ "INT33C0", (unsigned long)&lpt_dev_desc },
{ "INT33C1", (unsigned long)&lpt_dev_desc },
struct lpss_private_data *pdata)
{
const struct lpss_device_desc *dev_desc = pdata->dev_desc;
+ struct lpss_clk_data *clk_data;
if (!lpss_clk_dev)
lpt_register_clock_device();
- if (!dev_desc->clk_parent || !pdata->mmio_base
+ clk_data = platform_get_drvdata(lpss_clk_dev);
+ if (!clk_data)
+ return -ENODEV;
+
+ if (dev_desc->clkdev_name) {
+ clk_register_clkdev(clk_data->clk, dev_desc->clkdev_name,
+ dev_name(&adev->dev));
+ return 0;
+ }
+
+ if (!pdata->mmio_base
|| pdata->mmio_size < dev_desc->prv_offset + LPSS_CLK_SIZE)
return -ENODATA;
pdata->clk = clk_register_gate(NULL, dev_name(&adev->dev),
- dev_desc->clk_parent, 0,
+ clk_data->name, 0,
pdata->mmio_base + dev_desc->prv_offset,
0, 0, NULL);
if (IS_ERR(pdata->clk))
+++ /dev/null
-/*
- * Support for Core System Resources Table (CSRT)
- *
- * Copyright (C) 2013, Intel Corporation
- * Authors: Mika Westerberg <mika.westerberg@linux.intel.com>
- * Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#define pr_fmt(fmt) "ACPI: CSRT: " fmt
-
-#include <linux/acpi.h>
-#include <linux/device.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/sizes.h>
-
-ACPI_MODULE_NAME("CSRT");
-
-static int __init acpi_csrt_parse_shared_info(struct platform_device *pdev,
- const struct acpi_csrt_group *grp)
-{
- const struct acpi_csrt_shared_info *si;
- struct resource res[3];
- size_t nres;
- int ret;
-
- memset(res, 0, sizeof(res));
- nres = 0;
-
- si = (const struct acpi_csrt_shared_info *)&grp[1];
- /*
- * The peripherals that are listed on CSRT typically support only
- * 32-bit addresses so we only use the low part of MMIO base for
- * now.
- */
- if (!si->mmio_base_high && si->mmio_base_low) {
- /*
- * There is no size of the memory resource in shared_info
- * so we assume that it is 4k here.
- */
- res[nres].start = si->mmio_base_low;
- res[nres].end = res[0].start + SZ_4K - 1;
- res[nres++].flags = IORESOURCE_MEM;
- }
-
- if (si->gsi_interrupt) {
- int irq = acpi_register_gsi(NULL, si->gsi_interrupt,
- si->interrupt_mode,
- si->interrupt_polarity);
- res[nres].start = irq;
- res[nres].end = irq;
- res[nres++].flags = IORESOURCE_IRQ;
- }
-
- if (si->base_request_line || si->num_handshake_signals) {
- /*
- * We pass the driver a DMA resource describing the range
- * of request lines the device supports.
- */
- res[nres].start = si->base_request_line;
- res[nres].end = res[nres].start + si->num_handshake_signals - 1;
- res[nres++].flags = IORESOURCE_DMA;
- }
-
- ret = platform_device_add_resources(pdev, res, nres);
- if (ret) {
- if (si->gsi_interrupt)
- acpi_unregister_gsi(si->gsi_interrupt);
- return ret;
- }
-
- return 0;
-}
-
-static int __init
-acpi_csrt_parse_resource_group(const struct acpi_csrt_group *grp)
-{
- struct platform_device *pdev;
- char vendor[5], name[16];
- int ret, i;
-
- vendor[0] = grp->vendor_id;
- vendor[1] = grp->vendor_id >> 8;
- vendor[2] = grp->vendor_id >> 16;
- vendor[3] = grp->vendor_id >> 24;
- vendor[4] = '\0';
-
- if (grp->shared_info_length != sizeof(struct acpi_csrt_shared_info))
- return -ENODEV;
-
- snprintf(name, sizeof(name), "%s%04X", vendor, grp->device_id);
- pdev = platform_device_alloc(name, PLATFORM_DEVID_AUTO);
- if (!pdev)
- return -ENOMEM;
-
- /* Add resources based on the shared info */
- ret = acpi_csrt_parse_shared_info(pdev, grp);
- if (ret)
- goto fail;
-
- ret = platform_device_add(pdev);
- if (ret)
- goto fail;
-
- for (i = 0; i < pdev->num_resources; i++)
- dev_dbg(&pdev->dev, "%pR\n", &pdev->resource[i]);
-
- return 0;
-
-fail:
- platform_device_put(pdev);
- return ret;
-}
-
-/*
- * CSRT or Core System Resources Table is a proprietary ACPI table
- * introduced by Microsoft. This table can contain devices that are not in
- * the system DSDT table. In particular DMA controllers might be described
- * here.
- *
- * We present these devices as normal platform devices that don't have ACPI
- * IDs or handle. The platform device name will be something like
- * <VENDOR><DEVID>.<n>.auto for example: INTL9C06.0.auto.
- */
-void __init acpi_csrt_init(void)
-{
- struct acpi_csrt_group *grp, *end;
- struct acpi_table_csrt *csrt;
- acpi_status status;
- int ret;
-
- status = acpi_get_table(ACPI_SIG_CSRT, 0,
- (struct acpi_table_header **)&csrt);
- if (ACPI_FAILURE(status)) {
- if (status != AE_NOT_FOUND)
- pr_warn("failed to get the CSRT table\n");
- return;
- }
-
- pr_debug("parsing CSRT table for devices\n");
-
- grp = (struct acpi_csrt_group *)(csrt + 1);
- end = (struct acpi_csrt_group *)((void *)csrt + csrt->header.length);
-
- while (grp < end) {
- ret = acpi_csrt_parse_resource_group(grp);
- if (ret) {
- pr_warn("error in parsing resource group: %d\n", ret);
- return;
- }
-
- grp = (struct acpi_csrt_group *)((void *)grp + grp->length);
- }
-}
#define _COMPONENT ACPI_POWER_COMPONENT
ACPI_MODULE_NAME("device_pm");
-static DEFINE_MUTEX(acpi_pm_notifier_lock);
-
-/**
- * acpi_add_pm_notifier - Register PM notifier for given ACPI device.
- * @adev: ACPI device to add the notifier for.
- * @context: Context information to pass to the notifier routine.
- *
- * NOTE: @adev need not be a run-wake or wakeup device to be a valid source of
- * PM wakeup events. For example, wakeup events may be generated for bridges
- * if one of the devices below the bridge is signaling wakeup, even if the
- * bridge itself doesn't have a wakeup GPE associated with it.
- */
-acpi_status acpi_add_pm_notifier(struct acpi_device *adev,
- acpi_notify_handler handler, void *context)
-{
- acpi_status status = AE_ALREADY_EXISTS;
-
- mutex_lock(&acpi_pm_notifier_lock);
-
- if (adev->wakeup.flags.notifier_present)
- goto out;
-
- status = acpi_install_notify_handler(adev->handle,
- ACPI_SYSTEM_NOTIFY,
- handler, context);
- if (ACPI_FAILURE(status))
- goto out;
-
- adev->wakeup.flags.notifier_present = true;
-
- out:
- mutex_unlock(&acpi_pm_notifier_lock);
- return status;
-}
-
-/**
- * acpi_remove_pm_notifier - Unregister PM notifier from given ACPI device.
- * @adev: ACPI device to remove the notifier from.
- */
-acpi_status acpi_remove_pm_notifier(struct acpi_device *adev,
- acpi_notify_handler handler)
-{
- acpi_status status = AE_BAD_PARAMETER;
-
- mutex_lock(&acpi_pm_notifier_lock);
-
- if (!adev->wakeup.flags.notifier_present)
- goto out;
-
- status = acpi_remove_notify_handler(adev->handle,
- ACPI_SYSTEM_NOTIFY,
- handler);
- if (ACPI_FAILURE(status))
- goto out;
-
- adev->wakeup.flags.notifier_present = false;
-
- out:
- mutex_unlock(&acpi_pm_notifier_lock);
- return status;
-}
-
/**
* acpi_power_state_string - String representation of ACPI device power state.
* @state: ACPI device power state to return the string representation of.
}
EXPORT_SYMBOL(acpi_bus_power_manageable);
+#ifdef CONFIG_PM
+static DEFINE_MUTEX(acpi_pm_notifier_lock);
+
+/**
+ * acpi_add_pm_notifier - Register PM notifier for given ACPI device.
+ * @adev: ACPI device to add the notifier for.
+ * @context: Context information to pass to the notifier routine.
+ *
+ * NOTE: @adev need not be a run-wake or wakeup device to be a valid source of
+ * PM wakeup events. For example, wakeup events may be generated for bridges
+ * if one of the devices below the bridge is signaling wakeup, even if the
+ * bridge itself doesn't have a wakeup GPE associated with it.
+ */
+acpi_status acpi_add_pm_notifier(struct acpi_device *adev,
+ acpi_notify_handler handler, void *context)
+{
+ acpi_status status = AE_ALREADY_EXISTS;
+
+ mutex_lock(&acpi_pm_notifier_lock);
+
+ if (adev->wakeup.flags.notifier_present)
+ goto out;
+
+ status = acpi_install_notify_handler(adev->handle,
+ ACPI_SYSTEM_NOTIFY,
+ handler, context);
+ if (ACPI_FAILURE(status))
+ goto out;
+
+ adev->wakeup.flags.notifier_present = true;
+
+ out:
+ mutex_unlock(&acpi_pm_notifier_lock);
+ return status;
+}
+
+/**
+ * acpi_remove_pm_notifier - Unregister PM notifier from given ACPI device.
+ * @adev: ACPI device to remove the notifier from.
+ */
+acpi_status acpi_remove_pm_notifier(struct acpi_device *adev,
+ acpi_notify_handler handler)
+{
+ acpi_status status = AE_BAD_PARAMETER;
+
+ mutex_lock(&acpi_pm_notifier_lock);
+
+ if (!adev->wakeup.flags.notifier_present)
+ goto out;
+
+ status = acpi_remove_notify_handler(adev->handle,
+ ACPI_SYSTEM_NOTIFY,
+ handler);
+ if (ACPI_FAILURE(status))
+ goto out;
+
+ adev->wakeup.flags.notifier_present = false;
+
+ out:
+ mutex_unlock(&acpi_pm_notifier_lock);
+ return status;
+}
+
bool acpi_bus_can_wakeup(acpi_handle handle)
{
struct acpi_device *device;
mutex_unlock(&adev->physical_node_lock);
}
EXPORT_SYMBOL_GPL(acpi_dev_pm_remove_dependent);
+#endif /* CONFIG_PM */
void acpi_pci_root_hp_init(void);
void acpi_platform_init(void);
int acpi_sysfs_init(void);
-void acpi_csrt_init(void);
#ifdef CONFIG_ACPI_CONTAINER
void acpi_container_init(void);
#else
/* bus enumerate */
printk(KERN_DEBUG "%s: Bus check notify on %s\n", __func__,
(char *)buffer.pointer);
- if (!root)
+ if (root)
+ acpiphp_check_host_bridge(handle);
+ else
handle_root_bridge_insertion(handle);
break;
acpi_pci_link_init();
acpi_platform_init();
acpi_lpss_init();
- acpi_csrt_init();
acpi_container_init();
acpi_memory_hotplug_init();
DMI_MATCH(DMI_PRODUCT_NAME, "UL30VT"),
},
},
+ {
+ .callback = video_detect_force_vendor,
+ .ident = "Asus UL30A",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK Computer Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "UL30A"),
+ },
+ },
{ },
};
return subsys_register(subsys, groups, virtual_dir);
}
+EXPORT_SYMBOL_GPL(subsys_virtual_register);
int __init buses_init(void)
{
if (dev) {
WARN(((attr->attr.mode & S_IWUGO) && !attr->store),
- "Write permission without 'store'\n");
+ "Attribute %s: write permission without 'store'\n",
+ attr->attr.name);
WARN(((attr->attr.mode & S_IRUGO) && !attr->show),
- "Read permission without 'show'\n");
+ "Attribute %s: read permission without 'show'\n",
+ attr->attr.name);
error = sysfs_create_file(&dev->kobj, &attr->attr);
}
{ BCMA_CORE_I2S, "I2S" },
{ BCMA_CORE_SDR_DDR1_MEM_CTL, "SDR/DDR1 Memory Controller" },
{ BCMA_CORE_SHIM, "SHIM" },
+ { BCMA_CORE_PCIE2, "PCIe Gen2" },
+ { BCMA_CORE_ARM_CR4, "ARM CR4" },
{ BCMA_CORE_DEFAULT, "Default" },
};
spin_lock(&brd->brd_lock);
idx = sector >> PAGE_SECTORS_SHIFT;
+ page->index = idx;
if (radix_tree_insert(&brd->brd_pages, idx, page)) {
__free_page(page);
page = radix_tree_lookup(&brd->brd_pages, idx);
BUG_ON(!page);
BUG_ON(page->index != idx);
- } else
- page->index = idx;
+ }
spin_unlock(&brd->brd_lock);
radix_tree_preload_end();
dev_dbg(&dev->dev, "ace_probe(%p)\n", dev);
/* device id and bus width */
- of_property_read_u32(dev->dev.of_node, "port-number", &id);
- if (id < 0)
+ if (of_property_read_u32(dev->dev.of_node, "port-number", &id))
id = 0;
if (of_find_property(dev->dev.of_node, "8-bit", NULL))
bus_width = ACE_BUS_WIDTH_8;
return -EFAULT;
break;
case LPGETSTATUS:
+ if (mutex_lock_interruptible(&lp_table[minor].port_mutex))
+ return -EINTR;
lp_claim_parport_or_block (&lp_table[minor]);
status = r_str(minor);
lp_release_parport (&lp_table[minor]);
+ mutex_unlock(&lp_table[minor].port_mutex);
if (copy_to_user(argp, &status, sizeof(int)))
return -EFAULT;
if (r->entropy_count / 8 < min + reserved) {
nbytes = 0;
} else {
+ int entropy_count, orig;
+retry:
+ entropy_count = orig = ACCESS_ONCE(r->entropy_count);
/* If limited, never pull more than available */
- if (r->limit && nbytes + reserved >= r->entropy_count / 8)
- nbytes = r->entropy_count/8 - reserved;
-
- if (r->entropy_count / 8 >= nbytes + reserved)
- r->entropy_count -= nbytes*8;
- else
- r->entropy_count = reserved;
+ if (r->limit && nbytes + reserved >= entropy_count / 8)
+ nbytes = entropy_count/8 - reserved;
+
+ if (entropy_count / 8 >= nbytes + reserved) {
+ entropy_count -= nbytes*8;
+ if (cmpxchg(&r->entropy_count, orig, entropy_count) != orig)
+ goto retry;
+ } else {
+ entropy_count = reserved;
+ if (cmpxchg(&r->entropy_count, orig, entropy_count) != orig)
+ goto retry;
+ }
- if (r->entropy_count < random_write_wakeup_thresh)
+ if (entropy_count < random_write_wakeup_thresh)
wakeup_write = 1;
}
{
ssize_t ret = 0, i;
__u8 tmp[EXTRACT_SIZE];
+ unsigned long flags;
/* if last_data isn't primed, we need EXTRACT_SIZE extra bytes */
- if (fips_enabled && !r->last_data_init)
- nbytes += EXTRACT_SIZE;
+ if (fips_enabled) {
+ spin_lock_irqsave(&r->lock, flags);
+ if (!r->last_data_init) {
+ r->last_data_init = true;
+ spin_unlock_irqrestore(&r->lock, flags);
+ trace_extract_entropy(r->name, EXTRACT_SIZE,
+ r->entropy_count, _RET_IP_);
+ xfer_secondary_pool(r, EXTRACT_SIZE);
+ extract_buf(r, tmp);
+ spin_lock_irqsave(&r->lock, flags);
+ memcpy(r->last_data, tmp, EXTRACT_SIZE);
+ }
+ spin_unlock_irqrestore(&r->lock, flags);
+ }
trace_extract_entropy(r->name, nbytes, r->entropy_count, _RET_IP_);
xfer_secondary_pool(r, nbytes);
extract_buf(r, tmp);
if (fips_enabled) {
- unsigned long flags;
-
-
- /* prime last_data value if need be, per fips 140-2 */
- if (!r->last_data_init) {
- spin_lock_irqsave(&r->lock, flags);
- memcpy(r->last_data, tmp, EXTRACT_SIZE);
- r->last_data_init = true;
- nbytes -= EXTRACT_SIZE;
- spin_unlock_irqrestore(&r->lock, flags);
- extract_buf(r, tmp);
- }
-
spin_lock_irqsave(&r->lock, flags);
if (!memcmp(tmp, r->last_data, EXTRACT_SIZE))
panic("Hardware RNG duplicated output!\n");
{
int ret = -ENOMEM;
- tpk_port.port.ops = &null_ops;
mutex_init(&tpk_port.port_write_mutex);
ttyprintk_driver = tty_alloc_driver(1,
return PTR_ERR(ttyprintk_driver);
tty_port_init(&tpk_port.port);
+ tpk_port.port.ops = &null_ops;
ttyprintk_driver->driver_name = "ttyprintk";
ttyprintk_driver->name = "ttyprintk";
struct clk *clk;
int i;
+ /* ac97 */
+ clk = tegra_clk_register_periph_gate("ac97", "pll_a_out0",
+ TEGRA_PERIPH_ON_APB,
+ clk_base, 0, 3, &periph_l_regs,
+ periph_clk_enb_refcnt);
+ clk_register_clkdev(clk, NULL, "tegra20-ac97");
+ clks[ac97] = clk;
+
/* apbdma */
clk = tegra_clk_register_periph_gate("apbdma", "pclk", 0, clk_base,
0, 34, &periph_h_regs,
{uartc, pll_p, 0, 0},
{uartd, pll_p, 0, 0},
{uarte, pll_p, 0, 0},
- {usbd, clk_max, 12000000, 0},
- {usb2, clk_max, 12000000, 0},
- {usb3, clk_max, 12000000, 0},
{pll_a, clk_max, 56448000, 1},
{pll_a_out0, clk_max, 11289600, 1},
{cdev1, clk_max, 0, 1},
#include <linux/clk-provider.h>
#include <linux/err.h>
#include <linux/module.h>
+#include <linux/platform_data/clk-lpss.h>
#include <linux/platform_device.h>
#define PRV_CLOCK_PARAMS 0x800
static int lpt_clk_probe(struct platform_device *pdev)
{
+ struct lpss_clk_data *drvdata;
struct clk *clk;
+ drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
+ if (!drvdata)
+ return -ENOMEM;
+
/* LPSS free running clock */
- clk = clk_register_fixed_rate(&pdev->dev, "lpss_clk", NULL, CLK_IS_ROOT,
- 100000000);
+ drvdata->name = "lpss_clk";
+ clk = clk_register_fixed_rate(&pdev->dev, drvdata->name, NULL,
+ CLK_IS_ROOT, 100000000);
if (IS_ERR(clk))
return PTR_ERR(clk);
- /* Shared DMA clock */
- clk_register_clkdev(clk, "hclk", "INTL9C60.0.auto");
+ drvdata->clk = clk;
+ platform_set_drvdata(pdev, drvdata);
return 0;
}
config X86_E_POWERSAVER
tristate "VIA C7 Enhanced PowerSaver (DANGEROUS)"
select CPU_FREQ_TABLE
- depends on X86_32
+ depends on X86_32 && ACPI_PROCESSOR
help
This adds the CPUFreq driver for VIA C7 processors. However, this driver
does not have any safeguards to prevent operating the CPU out of spec
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+#include <linux/cpu.h>
#include <linux/cpufreq.h>
#include <linux/device.h>
#include <linux/export.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/opp.h>
+#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/types.h>
#include "arm_big_little.h"
-static int dt_init_opp_table(struct device *cpu_dev)
+/* get cpu node with valid operating-points */
+static struct device_node *get_cpu_node_with_valid_op(int cpu)
{
- struct device_node *np, *parent;
- int count = 0, ret;
+ struct device_node *np = NULL, *parent;
+ int count = 0;
parent = of_find_node_by_path("/cpus");
if (!parent) {
pr_err("failed to find OF /cpus\n");
- return -ENOENT;
+ return NULL;
}
for_each_child_of_node(parent, np) {
- if (count++ != cpu_dev->id)
+ if (count++ != cpu)
continue;
if (!of_get_property(np, "operating-points", NULL)) {
- ret = -ENODATA;
- } else {
- cpu_dev->of_node = np;
- ret = of_init_opp_table(cpu_dev);
+ of_node_put(np);
+ np = NULL;
}
- of_node_put(np);
- of_node_put(parent);
- return ret;
+ break;
}
- return -ENODEV;
+ of_node_put(parent);
+ return np;
+}
+
+static int dt_init_opp_table(struct device *cpu_dev)
+{
+ struct device_node *np;
+ int ret;
+
+ np = get_cpu_node_with_valid_op(cpu_dev->id);
+ if (!np)
+ return -ENODATA;
+
+ cpu_dev->of_node = np;
+ ret = of_init_opp_table(cpu_dev);
+ of_node_put(np);
+
+ return ret;
}
static int dt_get_transition_latency(struct device *cpu_dev)
{
- struct device_node *np, *parent;
+ struct device_node *np;
u32 transition_latency = CPUFREQ_ETERNAL;
- int count = 0;
- parent = of_find_node_by_path("/cpus");
- if (!parent) {
- pr_info("Failed to find OF /cpus. Use CPUFREQ_ETERNAL transition latency\n");
+ np = get_cpu_node_with_valid_op(cpu_dev->id);
+ if (!np)
return CPUFREQ_ETERNAL;
- }
-
- for_each_child_of_node(parent, np) {
- if (count++ != cpu_dev->id)
- continue;
- of_property_read_u32(np, "clock-latency", &transition_latency);
- of_node_put(np);
- of_node_put(parent);
+ of_property_read_u32(np, "clock-latency", &transition_latency);
+ of_node_put(np);
- return transition_latency;
- }
-
- pr_info("clock-latency isn't found, use CPUFREQ_ETERNAL transition latency\n");
- return CPUFREQ_ETERNAL;
+ pr_debug("%s: clock-latency: %d\n", __func__, transition_latency);
+ return transition_latency;
}
static struct cpufreq_arm_bL_ops dt_bL_ops = {
.init_opp_table = dt_init_opp_table,
};
-static int generic_bL_init(void)
+static int generic_bL_probe(struct platform_device *pdev)
{
+ struct device_node *np;
+
+ np = get_cpu_node_with_valid_op(0);
+ if (!np)
+ return -ENODEV;
+
+ of_node_put(np);
return bL_cpufreq_register(&dt_bL_ops);
}
-module_init(generic_bL_init);
-static void generic_bL_exit(void)
+static int generic_bL_remove(struct platform_device *pdev)
{
- return bL_cpufreq_unregister(&dt_bL_ops);
+ bL_cpufreq_unregister(&dt_bL_ops);
+ return 0;
}
-module_exit(generic_bL_exit);
+
+static struct platform_driver generic_bL_platdrv = {
+ .driver = {
+ .name = "arm-bL-cpufreq-dt",
+ .owner = THIS_MODULE,
+ },
+ .probe = generic_bL_probe,
+ .remove = generic_bL_remove,
+};
+module_platform_driver(generic_bL_platdrv);
MODULE_AUTHOR("Viresh Kumar <viresh.kumar@linaro.org>");
MODULE_DESCRIPTION("Generic ARM big LITTLE cpufreq driver via DT");
/* end old governor */
if (data->governor) {
__cpufreq_governor(data, CPUFREQ_GOV_STOP);
+ unlock_policy_rwsem_write(policy->cpu);
__cpufreq_governor(data,
CPUFREQ_GOV_POLICY_EXIT);
+ lock_policy_rwsem_write(policy->cpu);
}
/* start new governor */
data->governor = policy->governor;
if (!__cpufreq_governor(data, CPUFREQ_GOV_POLICY_INIT)) {
- if (!__cpufreq_governor(data, CPUFREQ_GOV_START))
+ if (!__cpufreq_governor(data, CPUFREQ_GOV_START)) {
failed = 0;
- else
+ } else {
+ unlock_policy_rwsem_write(policy->cpu);
__cpufreq_governor(data,
CPUFREQ_GOV_POLICY_EXIT);
+ lock_policy_rwsem_write(policy->cpu);
+ }
}
if (failed) {
static const struct x86_cpu_id intel_pstate_cpu_ids[] = {
ICPU(0x2a, default_policy),
ICPU(0x2d, default_policy),
+ ICPU(0x3a, default_policy),
{}
};
MODULE_DEVICE_TABLE(x86cpu, intel_pstate_cpu_ids);
#include <linux/platform_device.h>
#include <asm/clock.h>
+#include <asm/idle.h>
#include <asm/mach-loongson/loongson.h>
LOONGSON_CHIPCFG0 &= ~0x7; /* Put CPU into wait mode */
LOONGSON_CHIPCFG0 = cpu_freq; /* Restore CPU state */
spin_unlock_irqrestore(&loongson2_wait_lock, flags);
+ local_irq_enable();
}
static int __init cpufreq_init(void)
.cra_blocksize = AES_BLOCK_SIZE,
.cra_ctxsize = sizeof(struct nx_crypto_ctx),
.cra_type = &crypto_blkcipher_type,
+ .cra_alignmask = 0xf,
.cra_module = THIS_MODULE,
.cra_init = nx_crypto_ctx_aes_cbc_init,
.cra_exit = nx_crypto_ctx_exit,
.cra_priority = 300,
.cra_flags = CRYPTO_ALG_TYPE_BLKCIPHER,
.cra_blocksize = AES_BLOCK_SIZE,
+ .cra_alignmask = 0xf,
.cra_ctxsize = sizeof(struct nx_crypto_ctx),
.cra_type = &crypto_blkcipher_type,
.cra_module = THIS_MODULE,
if (enc)
NX_CPB_FDM(csbcpb) |= NX_FDM_ENDE_ENCRYPT;
else
- nbytes -= AES_BLOCK_SIZE;
+ nbytes -= crypto_aead_authsize(crypto_aead_reqtfm(req));
csbcpb->cpb.aes_gcm.bit_length_data = nbytes * 8;
* 1: <= SHA256_BLOCK_SIZE: copy into state, return 0
* 2: > SHA256_BLOCK_SIZE: process X blocks, copy in leftover
*/
- if (len + sctx->count <= SHA256_BLOCK_SIZE) {
+ if (len + sctx->count < SHA256_BLOCK_SIZE) {
memcpy(sctx->buf + sctx->count, data, len);
sctx->count += len;
goto out;
atomic_inc(&(nx_ctx->stats->sha256_ops));
/* copy the leftover back into the state struct */
- memcpy(sctx->buf, data + len - leftover, leftover);
+ if (leftover)
+ memcpy(sctx->buf, data + len - leftover, leftover);
sctx->count = leftover;
csbcpb->cpb.sha256.message_bit_length += (u64)
struct nx_sg *in_sg, *out_sg;
int rc;
+
if (NX_CPB_FDM(csbcpb) & NX_FDM_CONTINUATION) {
/* we've hit the nx chip previously, now we're finalizing,
* so copy over the partial digest */
atomic_inc(&(nx_ctx->stats->sha256_ops));
- atomic64_add(csbcpb->cpb.sha256.message_bit_length,
+ atomic64_add(csbcpb->cpb.sha256.message_bit_length / 8,
&(nx_ctx->stats->sha256_bytes));
memcpy(out, csbcpb->cpb.sha256.message_digest, SHA256_DIGEST_SIZE);
out:
* 1: <= SHA512_BLOCK_SIZE: copy into state, return 0
* 2: > SHA512_BLOCK_SIZE: process X blocks, copy in leftover
*/
- if ((u64)len + sctx->count[0] <= SHA512_BLOCK_SIZE) {
+ if ((u64)len + sctx->count[0] < SHA512_BLOCK_SIZE) {
memcpy(sctx->buf + sctx->count[0], data, len);
sctx->count[0] += len;
goto out;
atomic_inc(&(nx_ctx->stats->sha512_ops));
/* copy the leftover back into the state struct */
- memcpy(sctx->buf, data + len - leftover, leftover);
+ if (leftover)
+ memcpy(sctx->buf, data + len - leftover, leftover);
sctx->count[0] = leftover;
spbc_bits = csbcpb->cpb.sha512.spbc * 8;
goto out;
atomic_inc(&(nx_ctx->stats->sha512_ops));
- atomic64_add(csbcpb->cpb.sha512.message_bit_length_lo,
+ atomic64_add(csbcpb->cpb.sha512.message_bit_length_lo / 8,
&(nx_ctx->stats->sha512_bytes));
memcpy(out, csbcpb->cpb.sha512.message_digest, SHA512_DIGEST_SIZE);
{
struct nx_sg *nx_insg = nx_ctx->in_sg;
struct nx_sg *nx_outsg = nx_ctx->out_sg;
- struct blkcipher_walk walk;
- int rc;
-
- blkcipher_walk_init(&walk, dst, src, nbytes);
- rc = blkcipher_walk_virt_block(desc, &walk, AES_BLOCK_SIZE);
- if (rc)
- goto out;
if (iv)
- memcpy(iv, walk.iv, AES_BLOCK_SIZE);
+ memcpy(iv, desc->info, AES_BLOCK_SIZE);
- while (walk.nbytes) {
- nx_insg = nx_build_sg_list(nx_insg, walk.src.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
- nx_outsg = nx_build_sg_list(nx_outsg, walk.dst.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
-
- rc = blkcipher_walk_done(desc, &walk, 0);
- if (rc)
- break;
- }
-
- if (walk.nbytes) {
- nx_insg = nx_build_sg_list(nx_insg, walk.src.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
- nx_outsg = nx_build_sg_list(nx_outsg, walk.dst.virt.addr,
- walk.nbytes, nx_ctx->ap->sglen);
-
- rc = 0;
- }
+ nx_insg = nx_walk_and_build(nx_insg, nx_ctx->ap->sglen, src, 0, nbytes);
+ nx_outsg = nx_walk_and_build(nx_outsg, nx_ctx->ap->sglen, dst, 0, nbytes);
/* these lengths should be negative, which will indicate to phyp that
* the input and output parameters are scatterlists, not linear
* buffers */
nx_ctx->op.inlen = (nx_ctx->in_sg - nx_insg) * sizeof(struct nx_sg);
nx_ctx->op.outlen = (nx_ctx->out_sg - nx_outsg) * sizeof(struct nx_sg);
-out:
- return rc;
+
+ return 0;
}
/**
if (rc)
goto out;
+ nx_driver.of.status = NX_OKAY;
+
rc = crypto_register_alg(&nx_ecb_aes_alg);
if (rc)
goto out;
if (rc)
goto out_unreg_s512;
- nx_driver.of.status = NX_OKAY;
-
goto out;
out_unreg_s512:
* Based on of-dma.c
*
* Copyright (C) 2013, Intel Corporation
- * Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+ * Authors: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+ * Mika Westerberg <mika.westerberg@linux.intel.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
#include <linux/list.h>
#include <linux/mutex.h>
#include <linux/slab.h>
+#include <linux/ioport.h>
#include <linux/acpi.h>
#include <linux/acpi_dma.h>
static LIST_HEAD(acpi_dma_list);
static DEFINE_MUTEX(acpi_dma_lock);
+/**
+ * acpi_dma_parse_resource_group - match device and parse resource group
+ * @grp: CSRT resource group
+ * @adev: ACPI device to match with
+ * @adma: struct acpi_dma of the given DMA controller
+ *
+ * Returns 1 on success, 0 when no information is available, or appropriate
+ * errno value on error.
+ *
+ * In order to match a device from DSDT table to the corresponding CSRT device
+ * we use MMIO address and IRQ.
+ */
+static int acpi_dma_parse_resource_group(const struct acpi_csrt_group *grp,
+ struct acpi_device *adev, struct acpi_dma *adma)
+{
+ const struct acpi_csrt_shared_info *si;
+ struct list_head resource_list;
+ struct resource_list_entry *rentry;
+ resource_size_t mem = 0, irq = 0;
+ u32 vendor_id;
+ int ret;
+
+ if (grp->shared_info_length != sizeof(struct acpi_csrt_shared_info))
+ return -ENODEV;
+
+ INIT_LIST_HEAD(&resource_list);
+ ret = acpi_dev_get_resources(adev, &resource_list, NULL, NULL);
+ if (ret <= 0)
+ return 0;
+
+ list_for_each_entry(rentry, &resource_list, node) {
+ if (resource_type(&rentry->res) == IORESOURCE_MEM)
+ mem = rentry->res.start;
+ else if (resource_type(&rentry->res) == IORESOURCE_IRQ)
+ irq = rentry->res.start;
+ }
+
+ acpi_dev_free_resource_list(&resource_list);
+
+ /* Consider initial zero values as resource not found */
+ if (mem == 0 && irq == 0)
+ return 0;
+
+ si = (const struct acpi_csrt_shared_info *)&grp[1];
+
+ /* Match device by MMIO and IRQ */
+ if (si->mmio_base_low != mem || si->gsi_interrupt != irq)
+ return 0;
+
+ vendor_id = le32_to_cpu(grp->vendor_id);
+ dev_dbg(&adev->dev, "matches with %.4s%04X (rev %u)\n",
+ (char *)&vendor_id, grp->device_id, grp->revision);
+
+ /* Check if the request line range is available */
+ if (si->base_request_line == 0 && si->num_handshake_signals == 0)
+ return 0;
+
+ adma->base_request_line = si->base_request_line;
+ adma->end_request_line = si->base_request_line +
+ si->num_handshake_signals - 1;
+
+ dev_dbg(&adev->dev, "request line base: 0x%04x end: 0x%04x\n",
+ adma->base_request_line, adma->end_request_line);
+
+ return 1;
+}
+
+/**
+ * acpi_dma_parse_csrt - parse CSRT to exctract additional DMA resources
+ * @adev: ACPI device to match with
+ * @adma: struct acpi_dma of the given DMA controller
+ *
+ * CSRT or Core System Resources Table is a proprietary ACPI table
+ * introduced by Microsoft. This table can contain devices that are not in
+ * the system DSDT table. In particular DMA controllers might be described
+ * here.
+ *
+ * We are using this table to get the request line range of the specific DMA
+ * controller to be used later.
+ *
+ */
+static void acpi_dma_parse_csrt(struct acpi_device *adev, struct acpi_dma *adma)
+{
+ struct acpi_csrt_group *grp, *end;
+ struct acpi_table_csrt *csrt;
+ acpi_status status;
+ int ret;
+
+ status = acpi_get_table(ACPI_SIG_CSRT, 0,
+ (struct acpi_table_header **)&csrt);
+ if (ACPI_FAILURE(status)) {
+ if (status != AE_NOT_FOUND)
+ dev_warn(&adev->dev, "failed to get the CSRT table\n");
+ return;
+ }
+
+ grp = (struct acpi_csrt_group *)(csrt + 1);
+ end = (struct acpi_csrt_group *)((void *)csrt + csrt->header.length);
+
+ while (grp < end) {
+ ret = acpi_dma_parse_resource_group(grp, adev, adma);
+ if (ret < 0) {
+ dev_warn(&adev->dev,
+ "error in parsing resource group\n");
+ return;
+ }
+
+ grp = (struct acpi_csrt_group *)((void *)grp + grp->length);
+ }
+}
+
/**
* acpi_dma_controller_register - Register a DMA controller to ACPI DMA helpers
* @dev: struct device of DMA controller
adma->acpi_dma_xlate = acpi_dma_xlate;
adma->data = data;
+ acpi_dma_parse_csrt(adev, adma);
+
/* Now queue acpi_dma controller structure in list */
mutex_lock(&acpi_dma_lock);
list_add_tail(&adma->dma_controllers, &acpi_dma_list);
}
EXPORT_SYMBOL_GPL(devm_acpi_dma_controller_free);
+/**
+ * acpi_dma_update_dma_spec - prepare dma specifier to pass to translation function
+ * @adma: struct acpi_dma of DMA controller
+ * @dma_spec: dma specifier to update
+ *
+ * Returns 0, if no information is avaiable, -1 on mismatch, and 1 otherwise.
+ *
+ * Accordingly to ACPI 5.0 Specification Table 6-170 "Fixed DMA Resource
+ * Descriptor":
+ * DMA Request Line bits is a platform-relative number uniquely
+ * identifying the request line assigned. Request line-to-Controller
+ * mapping is done in a controller-specific OS driver.
+ * That's why we can safely adjust slave_id when the appropriate controller is
+ * found.
+ */
+static int acpi_dma_update_dma_spec(struct acpi_dma *adma,
+ struct acpi_dma_spec *dma_spec)
+{
+ /* Set link to the DMA controller device */
+ dma_spec->dev = adma->dev;
+
+ /* Check if the request line range is available */
+ if (adma->base_request_line == 0 && adma->end_request_line == 0)
+ return 0;
+
+ /* Check if slave_id falls to the range */
+ if (dma_spec->slave_id < adma->base_request_line ||
+ dma_spec->slave_id > adma->end_request_line)
+ return -1;
+
+ /*
+ * Here we adjust slave_id. It should be a relative number to the base
+ * request line.
+ */
+ dma_spec->slave_id -= adma->base_request_line;
+
+ return 1;
+}
+
struct acpi_dma_parser_data {
struct acpi_dma_spec dma_spec;
size_t index;
struct acpi_device *adev;
struct acpi_dma *adma;
struct dma_chan *chan = NULL;
+ int found;
/* Check if the device was enumerated by ACPI */
if (!dev || !ACPI_HANDLE(dev))
mutex_lock(&acpi_dma_lock);
list_for_each_entry(adma, &acpi_dma_list, dma_controllers) {
- dma_spec->dev = adma->dev;
+ /*
+ * We are not going to call translation function if slave_id
+ * doesn't fall to the request range.
+ */
+ found = acpi_dma_update_dma_spec(adma, dma_spec);
+ if (found < 0)
+ continue;
chan = adma->acpi_dma_xlate(dma_spec, adma);
- if (chan)
+ /*
+ * Try to get a channel only from the DMA controller that
+ * matches the slave_id. See acpi_dma_update_dma_spec()
+ * description for the details.
+ */
+ if (found > 0 || chan)
break;
}
amd64_inject_word_show, amd64_inject_word_store);
static DEVICE_ATTR(inject_ecc_vector, S_IRUGO | S_IWUSR,
amd64_inject_ecc_vector_show, amd64_inject_ecc_vector_store);
-static DEVICE_ATTR(inject_write, S_IRUGO | S_IWUSR,
+static DEVICE_ATTR(inject_write, S_IWUSR,
NULL, amd64_inject_write_store);
-static DEVICE_ATTR(inject_read, S_IRUGO | S_IWUSR,
+static DEVICE_ATTR(inject_read, S_IWUSR,
NULL, amd64_inject_read_store);
config GPIO_MCP23S08
tristate "Microchip MCP23xxx I/O expander"
- depends on SPI_MASTER || I2C
+ depends on (SPI_MASTER && !I2C) || I2C
help
SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
I/O expanders.
resource_size_t start, len;
struct lnw_gpio *lnw;
u32 gpio_base;
+ u32 irq_base;
int retval;
int ngpio = id->driver_data;
retval = -EFAULT;
goto err_ioremap;
}
+ irq_base = *(u32 *)base;
gpio_base = *((u32 *)base + 1);
/* release the IO mapping, since we already get the info from bar1 */
iounmap(base);
goto err_ioremap;
}
- lnw->domain = irq_domain_add_linear(pdev->dev.of_node, ngpio,
- &lnw_gpio_irq_ops, lnw);
- if (!lnw->domain) {
- retval = -ENOMEM;
- goto err_ioremap;
- }
-
lnw->reg_base = base;
lnw->chip.label = dev_name(&pdev->dev);
lnw->chip.request = lnw_gpio_request;
lnw->chip.ngpio = ngpio;
lnw->chip.can_sleep = 0;
lnw->pdev = pdev;
+
+ lnw->domain = irq_domain_add_simple(pdev->dev.of_node, ngpio, irq_base,
+ &lnw_gpio_irq_ops, lnw);
+ if (!lnw->domain) {
+ retval = -ENOMEM;
+ goto err_ioremap;
+ }
+
pci_set_drvdata(pdev, lnw);
retval = gpiochip_add(&lnw->chip);
if (retval) {
err_gpiochip_add:
while (--i >= 0) {
chip--;
- ret = gpiochip_remove(&chip->gpio);
- if (ret)
+ if (gpiochip_remove(&chip->gpio))
dev_err(&pdev->dev, "Failed gpiochip_remove(%d)\n", i);
}
kfree(chip_save);
err = bgpio_init(&port->bgc, &pdev->dev, 4,
port->base + PINCTRL_DIN(port),
- port->base + PINCTRL_DOUT(port), NULL,
+ port->base + PINCTRL_DOUT(port) + MXS_SET,
+ port->base + PINCTRL_DOUT(port) + MXS_CLR,
port->base + PINCTRL_DOE(port), NULL, 0);
if (err)
goto out_irqdesc_free;
bool is_mpuio;
bool dbck_flag;
bool loses_context;
+ bool context_valid;
int stride;
u32 width;
int context_loss_count;
bank->loses_context = true;
} else {
bank->loses_context = pdata->loses_context;
+
+ if (bank->loses_context)
+ bank->get_context_loss_count =
+ pdata->get_context_loss_count;
}
omap_gpio_chip_init(bank);
omap_gpio_show_rev(bank);
- if (bank->loses_context)
- bank->get_context_loss_count = pdata->get_context_loss_count;
-
pm_runtime_put(bank->dev);
list_add_tail(&bank->node, &omap_gpio_list);
return 0;
}
+static void omap_gpio_init_context(struct gpio_bank *p);
+
static int omap_gpio_runtime_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
int c;
spin_lock_irqsave(&bank->lock, flags);
+
+ /*
+ * On the first resume during the probe, the context has not
+ * been initialised and so initialise it now. Also initialise
+ * the context loss count.
+ */
+ if (bank->loses_context && !bank->context_valid) {
+ omap_gpio_init_context(bank);
+
+ if (bank->get_context_loss_count)
+ bank->context_loss_count =
+ bank->get_context_loss_count(bank->dev);
+ }
+
_gpio_dbck_enable(bank);
/*
}
#if defined(CONFIG_PM_RUNTIME)
+static void omap_gpio_init_context(struct gpio_bank *p)
+{
+ struct omap_gpio_reg_offs *regs = p->regs;
+ void __iomem *base = p->base;
+
+ p->context.ctrl = __raw_readl(base + regs->ctrl);
+ p->context.oe = __raw_readl(base + regs->direction);
+ p->context.wake_en = __raw_readl(base + regs->wkup_en);
+ p->context.leveldetect0 = __raw_readl(base + regs->leveldetect0);
+ p->context.leveldetect1 = __raw_readl(base + regs->leveldetect1);
+ p->context.risingdetect = __raw_readl(base + regs->risingdetect);
+ p->context.fallingdetect = __raw_readl(base + regs->fallingdetect);
+ p->context.irqenable1 = __raw_readl(base + regs->irqenable);
+ p->context.irqenable2 = __raw_readl(base + regs->irqenable2);
+
+ if (regs->set_dataout && p->regs->clr_dataout)
+ p->context.dataout = __raw_readl(base + regs->set_dataout);
+ else
+ p->context.dataout = __raw_readl(base + regs->dataout);
+
+ p->context_valid = true;
+}
+
static void omap_gpio_restore_context(struct gpio_bank *bank)
{
__raw_writel(bank->context.wake_en,
#else
#define omap_gpio_runtime_suspend NULL
#define omap_gpio_runtime_resume NULL
+static void omap_gpio_init_context(struct gpio_bank *p) {}
#endif
static const struct dev_pm_ops gpio_pm_ops = {
err_request_irq:
irq_free_descs(irq_base, gpio_pins[chip->ioh]);
- ret = gpiochip_remove(&chip->gpio);
- if (ret)
+ if (gpiochip_remove(&chip->gpio))
dev_err(&pdev->dev, "%s gpiochip_remove failed\n", __func__);
err_gpiochip_add:
return 0;
err_sch_gpio_resume:
- err = gpiochip_remove(&sch_gpio_core);
- if (err)
- dev_err(&pdev->dev, "%s failed, %d\n",
- "gpiochip_remove()", err);
+ if (gpiochip_remove(&sch_gpio_core))
+ dev_err(&pdev->dev, "%s gpiochip_remove failed\n", __func__);
err_sch_gpio_core:
release_region(res->start, resource_size(res));
return ret;
err_gpiob:
- ret = gpiochip_remove(&vb_gpio->gpioa);
+ if (gpiochip_remove(&vb_gpio->gpioa))
+ dev_err(&pdev->dev, "%s gpiochip_remove failed\n", __func__);
err_gpioa:
return ret;
return 0;
}
cur_cpu = (++next_vp % max_cpus);
- return cur_cpu;
+ return hv_context.vp_index[cur_cpu];
}
/*
#ifdef CONFIG_PM_SLEEP
static int exynos_adc_suspend(struct device *dev)
{
- struct platform_device *pdev = to_platform_device(dev);
- struct exynos_adc *info = platform_get_drvdata(pdev);
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct exynos_adc *info = iio_priv(indio_dev);
u32 con;
if (info->version == ADC_V2) {
static int exynos_adc_resume(struct device *dev)
{
- struct platform_device *pdev = to_platform_device(dev);
- struct exynos_adc *info = platform_get_drvdata(pdev);
+ struct iio_dev *indio_dev = dev_get_drvdata(dev);
+ struct exynos_adc *info = iio_priv(indio_dev);
int ret;
ret = regulator_enable(info->vdd);
goto read_error;
*val = *val >> ch->scan_type.shift;
+
+ err = st_sensors_set_enable(indio_dev, false);
}
mutex_unlock(&indio_dev->mlock);
config AD5064
tristate "Analog Devices AD5064 and similar multi-channel DAC driver"
- depends on (SPI_MASTER || I2C)
+ depends on (SPI_MASTER && I2C!=m) || I2C
help
Say yes here to build support for Analog Devices AD5024, AD5025, AD5044,
AD5045, AD5064, AD5064-1, AD5065, AD5628, AD5629R, AD5648, AD5666, AD5668,
config AD5380
tristate "Analog Devices AD5380/81/82/83/84/90/91/92 DAC driver"
- depends on (SPI_MASTER || I2C)
+ depends on (SPI_MASTER && I2C!=m) || I2C
select REGMAP_I2C if I2C
select REGMAP_SPI if SPI_MASTER
help
config AD5446
tristate "Analog Devices AD5446 and similar single channel DACs driver"
- depends on (SPI_MASTER || I2C)
+ depends on (SPI_MASTER && I2C!=m) || I2C
help
Say yes here to build support for Analog Devices AD5300, AD5301, AD5310,
AD5311, AD5320, AD5321, AD5444, AD5446, AD5450, AD5451, AD5452, AD5453,
wacom->id[idx] = (data[2] << 4) | (data[3] >> 4) |
((data[7] & 0x0f) << 20) | ((data[8] & 0xf0) << 12);
- switch (wacom->id[idx] & 0xfffff) {
+ switch (wacom->id[idx]) {
case 0x812: /* Inking pen */
case 0x801: /* Intuos3 Inking pen */
- case 0x20802: /* Intuos4 Inking Pen */
+ case 0x120802: /* Intuos4/5 Inking Pen */
case 0x012:
wacom->tool[idx] = BTN_TOOL_PENCIL;
break;
case 0x823: /* Intuos3 Grip Pen */
case 0x813: /* Intuos3 Classic Pen */
case 0x885: /* Intuos3 Marker Pen */
- case 0x802: /* Intuos4 General Pen */
- case 0x804: /* Intuos4 Marker Pen */
- case 0x40802: /* Intuos4 Classic Pen */
- case 0x18802: /* DTH2242 Grip Pen */
+ case 0x802: /* Intuos4/5 13HD/24HD General Pen */
+ case 0x804: /* Intuos4/5 13HD/24HD Marker Pen */
case 0x022:
+ case 0x100804: /* Intuos4/5 13HD/24HD Art Pen */
+ case 0x140802: /* Intuos4/5 13HD/24HD Classic Pen */
+ case 0x160802: /* Cintiq 13HD Pro Pen */
+ case 0x180802: /* DTH2242 Pen */
wacom->tool[idx] = BTN_TOOL_PEN;
break;
case 0x82b: /* Intuos3 Grip Pen Eraser */
case 0x81b: /* Intuos3 Classic Pen Eraser */
case 0x91b: /* Intuos3 Airbrush Eraser */
- case 0x80c: /* Intuos4 Marker Pen Eraser */
- case 0x80a: /* Intuos4 General Pen Eraser */
- case 0x4080a: /* Intuos4 Classic Pen Eraser */
- case 0x90a: /* Intuos4 Airbrush Eraser */
+ case 0x80c: /* Intuos4/5 13HD/24HD Marker Pen Eraser */
+ case 0x80a: /* Intuos4/5 13HD/24HD General Pen Eraser */
+ case 0x90a: /* Intuos4/5 13HD/24HD Airbrush Eraser */
+ case 0x14080a: /* Intuos4/5 13HD/24HD Classic Pen Eraser */
+ case 0x10090a: /* Intuos4/5 13HD/24HD Airbrush Eraser */
+ case 0x10080c: /* Intuos4/5 13HD/24HD Art Pen Eraser */
+ case 0x16080a: /* Cintiq 13HD Pro Pen Eraser */
+ case 0x18080a: /* DTH2242 Eraser */
wacom->tool[idx] = BTN_TOOL_RUBBER;
break;
case 0x912:
case 0x112:
case 0x913: /* Intuos3 Airbrush */
- case 0x902: /* Intuos4 Airbrush */
+ case 0x902: /* Intuos4/5 13HD/24HD Airbrush */
+ case 0x100902: /* Intuos4/5 13HD/24HD Airbrush */
wacom->tool[idx] = BTN_TOOL_AIRBRUSH;
break;
input_report_key(input, BTN_8, (data[3] & 0x80));
}
if (data[1] | (data[2] & 0x01) | data[3]) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
} else if (features->type == DTK) {
input_report_key(input, BTN_3, (data[6] & 0x08));
input_report_key(input, BTN_4, (data[6] & 0x10));
input_report_key(input, BTN_5, (data[6] & 0x20));
+ if (data[6] & 0x3f) {
+ input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
+ } else {
+ input_report_abs(input, ABS_MISC, 0);
+ }
+ } else if (features->type == WACOM_13HD) {
+ input_report_key(input, BTN_0, (data[3] & 0x01));
+ input_report_key(input, BTN_1, (data[4] & 0x01));
+ input_report_key(input, BTN_2, (data[4] & 0x02));
+ input_report_key(input, BTN_3, (data[4] & 0x04));
+ input_report_key(input, BTN_4, (data[4] & 0x08));
+ input_report_key(input, BTN_5, (data[4] & 0x10));
+ input_report_key(input, BTN_6, (data[4] & 0x20));
+ input_report_key(input, BTN_7, (data[4] & 0x40));
+ input_report_key(input, BTN_8, (data[4] & 0x80));
+ if ((data[3] & 0x01) | data[4]) {
+ input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
+ } else {
+ input_report_abs(input, ABS_MISC, 0);
+ }
} else if (features->type == WACOM_24HD) {
input_report_key(input, BTN_0, (data[6] & 0x01));
input_report_key(input, BTN_1, (data[6] & 0x02));
}
if (data[1] | data[2] | (data[3] & 0x1f) | data[4] | data[6] | data[8]) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
} else if (features->type >= INTUOS5S && features->type <= INTUOS5L) {
}
if (data[2] | (data[3] & 0x01) | data[4] | data[5]) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
} else {
if ((data[5] & 0x1f) | data[6] | (data[1] & 0x1f) |
data[2] | (data[3] & 0x1f) | data[4] | data[8] |
(data[7] & 0x01)) {
- input_report_key(input, wacom->tool[1], 1);
input_report_abs(input, ABS_MISC, PAD_DEVICE_ID);
} else {
- input_report_key(input, wacom->tool[1], 0);
input_report_abs(input, ABS_MISC, 0);
}
}
case INTUOS4L:
case CINTIQ:
case WACOM_BEE:
+ case WACOM_13HD:
case WACOM_21UX2:
case WACOM_22HD:
case WACOM_24HD:
__set_bit(KEY_PROG1, input_dev->keybit);
__set_bit(KEY_PROG2, input_dev->keybit);
__set_bit(KEY_PROG3, input_dev->keybit);
+
+ input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+ input_set_abs_params(input_dev, ABS_THROTTLE, 0, 71, 0, 0);
/* fall through */
case DTK:
for (i = 0; i < 6; i++)
__set_bit(BTN_0 + i, input_dev->keybit);
- input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
- input_set_abs_params(input_dev, ABS_THROTTLE, 0, 71, 0, 0);
-
__set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
wacom_setup_cintiq(wacom_wac);
wacom_setup_cintiq(wacom_wac);
break;
+ case WACOM_13HD:
+ for (i = 0; i < 9; i++)
+ __set_bit(BTN_0 + i, input_dev->keybit);
+
+ input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+ __set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+ wacom_setup_cintiq(wacom_wac);
+ break;
+
case INTUOS3:
case INTUOS3L:
__set_bit(BTN_4, input_dev->keybit);
static const struct wacom_features wacom_features_0xC6 =
{ "Wacom Cintiq 12WX", WACOM_PKGLEN_INTUOS, 53020, 33440, 1023,
63, WACOM_BEE, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0x304 =
+ { "Wacom Cintiq 13HD", WACOM_PKGLEN_INTUOS, 59552, 33848, 1023,
+ 63, WACOM_13HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
static const struct wacom_features wacom_features_0xC7 =
{ "Wacom DTU1931", WACOM_PKGLEN_GRAPHIRE, 37832, 30305, 511,
0, PL, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
static const struct wacom_features wacom_features_0xF0 =
{ "Wacom DTU1631", WACOM_PKGLEN_GRAPHIRE, 34623, 19553, 511,
0, DTU, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
+static const struct wacom_features wacom_features_0x57 =
+ { "Wacom DTK2241", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
+ 63, DTK, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES};
static const struct wacom_features wacom_features_0x59 = /* Pen */
{ "Wacom DTH2242", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
63, DTK, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
static const struct wacom_features wacom_features_0xFA =
{ "Wacom Cintiq 22HD", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
63, WACOM_22HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0x5B =
+ { "Wacom Cintiq 22HDT", WACOM_PKGLEN_INTUOS, 95840, 54260, 2047,
+ 63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES, .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x5e };
+static const struct wacom_features wacom_features_0x5E =
+ { "Wacom Cintiq 22HDT", .type = WACOM_24HDT,
+ .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x5b, .touch_max = 10 };
static const struct wacom_features wacom_features_0x90 =
{ "Wacom ISDv4 90", WACOM_PKGLEN_GRAPHIRE, 26202, 16325, 255,
0, TABLETPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
{ USB_DEVICE_WACOM(0x43) },
{ USB_DEVICE_WACOM(0x44) },
{ USB_DEVICE_WACOM(0x45) },
+ { USB_DEVICE_WACOM(0x57) },
{ USB_DEVICE_WACOM(0x59) },
{ USB_DEVICE_DETAILED(0x5D, USB_CLASS_HID, 0, 0) },
+ { USB_DEVICE_WACOM(0x5B) },
+ { USB_DEVICE_DETAILED(0x5E, USB_CLASS_HID, 0, 0) },
{ USB_DEVICE_WACOM(0xB0) },
{ USB_DEVICE_WACOM(0xB1) },
{ USB_DEVICE_WACOM(0xB2) },
{ USB_DEVICE_WACOM(0x100) },
{ USB_DEVICE_WACOM(0x101) },
{ USB_DEVICE_WACOM(0x10D) },
+ { USB_DEVICE_WACOM(0x304) },
{ USB_DEVICE_WACOM(0x4001) },
{ USB_DEVICE_WACOM(0x47) },
{ USB_DEVICE_WACOM(0xF4) },
WACOM_24HD,
CINTIQ,
WACOM_BEE,
+ WACOM_13HD,
WACOM_MO,
WIRELESS,
BAMBOO_PT,
input_set_abs_params(input_dev,
ABS_MT_POSITION_X, 0, EGALAX_MAX_X, 0, 0);
input_set_abs_params(input_dev,
- ABS_MT_POSITION_X, 0, EGALAX_MAX_Y, 0, 0);
+ ABS_MT_POSITION_Y, 0, EGALAX_MAX_Y, 0, 0);
input_mt_init_slots(input_dev, MAX_SUPPORT_POINTS, 0);
input_set_drvdata(input_dev, ts);
static inline struct capi_ctr *get_capi_ctr_by_nr(u16 contr)
{
- if (contr - 1 >= CAPI_MAXCONTR)
+ if (contr < 1 || contr - 1 >= CAPI_MAXCONTR)
return NULL;
return capi_controller[contr - 1];
{
lockdep_assert_held(&capi_controller_lock);
- if (applid - 1 >= CAPI_MAXAPPL)
+ if (applid < 1 || applid - 1 >= CAPI_MAXAPPL)
return NULL;
return capi_applications[applid - 1];
static inline struct capi20_appl *get_capi_appl_by_nr(u16 applid)
{
- if (applid - 1 >= CAPI_MAXAPPL)
+ if (applid < 1 || applid - 1 >= CAPI_MAXAPPL)
return NULL;
return rcu_dereference(capi_applications[applid - 1]);
{
.name = "led_1",
.port = 0x49,
- .mask = BIT(7),
+ .mask = BIT(6),
},
{
.name = "led_2",
.port = 0x49,
- .mask = BIT(6),
+ .mask = BIT(5),
},
{
.name = "led_3",
.port = 0x49,
- .mask = BIT(5),
+ .mask = BIT(4),
},
{
.name = "led_4",
.port = 0x49,
- .mask = BIT(4),
+ .mask = BIT(3),
},
{
.name = "led_5",
.port = 0x49,
- .mask = BIT(3),
+ .mask = BIT(2),
},
{
.name = "led_6",
.port = 0x49,
- .mask = BIT(2),
+ .mask = BIT(1),
},
{
.name = "led_7",
.port = 0x49,
- .mask = BIT(1),
+ .mask = BIT(0),
}
};
config AB8500_DEBUG
bool "Enable debug info via debugfs"
- depends on AB8500_CORE && DEBUG_FS
+ depends on AB8500_GPADC && DEBUG_FS
default y if DEBUG_FS
help
Select this option if you want debug information using the debug
config MFD_TPS65912
bool "TI TPS65912 Power Management chip"
depends on GPIOLIB
+ select MFD_CORE
help
If you say yes here you get support for the TPS65912 series of
PM chips.
#ifdef CONFIG_DEBUG_FS
static struct resource ab8500_debug_resources[] = {
+ {
+ .name = "IRQ_AB8500",
+ /*
+ * Number will be filled in. NOTE: this is deliberately
+ * not flagged as an IRQ in ordet to avoid remapping using
+ * the irqdomain in the MFD core, so that this IRQ passes
+ * unremapped to the debug code.
+ */
+ },
{
.name = "IRQ_FIRST",
.start = AB8500_INT_MAIN_EXT_CH_NOT_OK,
},
{
.name = "ab8500-gpadc",
+ .of_compatible = "stericsson,ab8500-gpadc",
.num_resources = ARRAY_SIZE(ab8500_gpadc_resources),
.resources = ab8500_gpadc_resources,
},
.of_compatible = "stericsson,ab8500-denc",
},
{
- .name = "ab8500-gpio",
+ .name = "pinctrl-ab8500",
.of_compatible = "stericsson,ab8500-gpio",
},
{
},
{
.name = "ab8500-gpadc",
+ .of_compatible = "stericsson,ab8500-gpadc",
.num_resources = ARRAY_SIZE(ab8505_gpadc_resources),
.resources = ab8505_gpadc_resources,
},
.name = "ab8500-leds",
},
{
- .name = "ab8500-gpio",
+ .name = "pinctrl-ab8505",
},
{
.name = "ab8500-usb",
},
{
.name = "ab8500-gpadc",
+ .of_compatible = "stericsson,ab8500-gpadc",
.num_resources = ARRAY_SIZE(ab8505_gpadc_resources),
.resources = ab8505_gpadc_resources,
},
.resources = ab8500_temp_resources,
},
{
- .name = "ab8500-gpio",
+ .name = "pinctrl-ab8540",
},
{
.name = "ab8540-usb",
if (ret)
return ret;
+#if CONFIG_DEBUG_FS
+ /* Pass to debugfs */
+ ab8500_debug_resources[0].start = ab8500->irq;
+ ab8500_debug_resources[0].end = ab8500->irq;
+#endif
+
if (is_ab9540(ab8500))
ret = mfd_add_devices(ab8500->dev, 0, ab9540_devs,
ARRAY_SIZE(ab9540_devs), NULL,
#include <linux/ctype.h>
#endif
-/* TODO: this file should not reference IRQ_DB8500_AB8500! */
-#include <mach/irqs.h>
-
static u32 debug_bank;
static u32 debug_address;
+static int irq_ab8500;
static int irq_first;
static int irq_last;
static u32 *irq_count;
{
if (line < num_interrupt_lines) {
num_interrupts[line]++;
- if (suspend_test_wake_cause_interrupt_is_mine(IRQ_DB8500_AB8500))
+ if (suspend_test_wake_cause_interrupt_is_mine(irq_ab8500))
num_wake_interrupts[line]++;
}
}
struct dentry *file;
int ret = -ENOMEM;
struct ab8500 *ab8500;
+ struct resource *res;
debug_bank = AB8500_MISC;
debug_address = AB8500_REV_REG & 0x00FF;
if (!event_name)
goto out_freedev_attr;
+ res = platform_get_resource_byname(plf, 0, "IRQ_AB8500");
+ if (!res) {
+ dev_err(&plf->dev, "AB8500 irq not found, err %d\n",
+ irq_first);
+ ret = -ENXIO;
+ goto out_freeevent_name;
+ }
+ irq_ab8500 = res->start;
+
irq_first = platform_get_irq_byname(plf, "IRQ_FIRST");
if (irq_first < 0) {
dev_err(&plf->dev, "First irq not found, err %d\n",
static int ab8500_gpadc_resume(struct device *dev)
{
struct ab8500_gpadc *gpadc = dev_get_drvdata(dev);
+ int ret;
- regulator_enable(gpadc->regu);
+ ret = regulator_enable(gpadc->regu);
+ if (ret)
+ dev_err(dev, "Failed to enable vtvout LDO: %d\n", ret);
pm_runtime_mark_last_busy(gpadc->dev);
pm_runtime_put_autosuspend(gpadc->dev);
mutex_unlock(&gpadc->ab8500_gpadc_lock);
- return 0;
+ return ret;
}
static int ab8500_gpadc_probe(struct platform_device *pdev)
static struct device *sysctrl_dev;
-void ab8500_power_off(void)
+static void ab8500_power_off(void)
{
sigset_t old;
sigset_t all;
plat = dev_get_platdata(sysctrl_dev->parent);
pdata = plat->sysctrl;
- if (pdata->reboot_reason_code)
+ if (pdata && pdata->reboot_reason_code)
reason = pdata->reboot_reason_code(cmd);
else
pr_warn("[%s] No reboot reason set. Default reason %d\n",
plat = dev_get_platdata(pdev->dev.parent);
- if (!(plat && plat->sysctrl))
+ if (!plat)
return -EINVAL;
- if (plat->pm_power_off)
+ sysctrl_dev = &pdev->dev;
+
+ if (!pm_power_off)
pm_power_off = ab8500_power_off;
pdata = plat->sysctrl;
-
if (pdata) {
int last, ret, i, j;
static int ab8500_sysctrl_remove(struct platform_device *pdev)
{
sysctrl_dev = NULL;
+
+ if (pm_power_off == ab8500_power_off)
+ pm_power_off = NULL;
+
return 0;
}
void abx500_dump_all_banks(void)
{
struct abx500_ops *ops;
- struct device dummy_child = {0};
+ struct device dummy_child = {NULL};
struct abx500_device_entry *dev_entry;
list_for_each_entry(dev_entry, &abx500_list, list) {
for (end = ptr + EC_MSG_PREAMBLE_COUNT; ptr != end; ptr++) {
if (*ptr == EC_MSG_HEADER) {
- dev_dbg(ec_dev->dev, "msg found at %ld\n",
+ dev_dbg(ec_dev->dev, "msg found at %zd\n",
ptr - ec_dev->din);
break;
}
* maximum-supported transfer size.
*/
todo = min(need_len, 256);
- dev_dbg(ec_dev->dev, "loop, todo=%d, need_len=%d, ptr=%ld\n",
+ dev_dbg(ec_dev->dev, "loop, todo=%d, need_len=%d, ptr=%zd\n",
todo, need_len, ptr - ec_dev->din);
memset(&trans, '\0', sizeof(trans));
need_len -= todo;
}
- dev_dbg(ec_dev->dev, "loop done, ptr=%ld\n", ptr - ec_dev->din);
+ dev_dbg(ec_dev->dev, "loop done, ptr=%zd\n", ptr - ec_dev->din);
return 0;
}
if (divsel == PRCM_DSI_PLLOUT_SEL_OFF)
divsel = dsiclk[n].divsel;
+ else
+ dsiclk[n].divsel = divsel;
switch (divsel) {
case PRCM_DSI_PLLOUT_SEL_PHI_4:
.num_resources = ARRAY_SIZE(db8500_thsens_resources),
.resources = db8500_thsens_resources,
.platform_data = &db8500_thsens_data,
+ .pdata_size = sizeof(db8500_thsens_data),
},
};
#include <linux/mfd/si476x-core.h>
+#include <asm/unaligned.h>
+
#define msb(x) ((u8)((u16) x >> 8))
#define lsb(x) ((u8)((u16) x & 0x00FF))
SI476X_ACF_SOFTMUTE_INT = (1 << 0),
SI476X_ACF_SMUTE = (1 << 0),
- SI476X_ACF_SMATTN = 0b11111,
+ SI476X_ACF_SMATTN = 0x1f,
SI476X_ACF_PILOT = (1 << 7),
SI476X_ACF_STBLEND = ~SI476X_ACF_PILOT,
};
if (err < 0)
return err;
else
- return be16_to_cpup((__be16 *)(resp + 2));
+ return get_unaligned_be16(resp + 2);
}
EXPORT_SYMBOL_GPL(si476x_core_cmd_get_property);
if (!report)
return err;
- report->snrhint = 0b00001000 & resp[1];
- report->snrlint = 0b00000100 & resp[1];
- report->rssihint = 0b00000010 & resp[1];
- report->rssilint = 0b00000001 & resp[1];
+ report->snrhint = 0x08 & resp[1];
+ report->snrlint = 0x04 & resp[1];
+ report->rssihint = 0x02 & resp[1];
+ report->rssilint = 0x01 & resp[1];
- report->bltf = 0b10000000 & resp[2];
- report->snr_ready = 0b00100000 & resp[2];
- report->rssiready = 0b00001000 & resp[2];
- report->afcrl = 0b00000010 & resp[2];
- report->valid = 0b00000001 & resp[2];
+ report->bltf = 0x80 & resp[2];
+ report->snr_ready = 0x20 & resp[2];
+ report->rssiready = 0x08 & resp[2];
+ report->afcrl = 0x02 & resp[2];
+ report->valid = 0x01 & resp[2];
- report->readfreq = be16_to_cpup((__be16 *)(resp + 3));
+ report->readfreq = get_unaligned_be16(resp + 3);
report->freqoff = resp[5];
report->rssi = resp[6];
report->snr = resp[7];
if (err < 0 || report == NULL)
return err;
- report->rdstpptyint = 0b00010000 & resp[1];
- report->rdspiint = 0b00001000 & resp[1];
- report->rdssyncint = 0b00000010 & resp[1];
- report->rdsfifoint = 0b00000001 & resp[1];
+ report->rdstpptyint = 0x10 & resp[1];
+ report->rdspiint = 0x08 & resp[1];
+ report->rdssyncint = 0x02 & resp[1];
+ report->rdsfifoint = 0x01 & resp[1];
- report->tpptyvalid = 0b00010000 & resp[2];
- report->pivalid = 0b00001000 & resp[2];
- report->rdssync = 0b00000010 & resp[2];
- report->rdsfifolost = 0b00000001 & resp[2];
+ report->tpptyvalid = 0x10 & resp[2];
+ report->pivalid = 0x08 & resp[2];
+ report->rdssync = 0x02 & resp[2];
+ report->rdsfifolost = 0x01 & resp[2];
- report->tp = 0b00100000 & resp[3];
- report->pty = 0b00011111 & resp[3];
+ report->tp = 0x20 & resp[3];
+ report->pty = 0x1f & resp[3];
- report->pi = be16_to_cpup((__be16 *)(resp + 4));
+ report->pi = get_unaligned_be16(resp + 4);
report->rdsfifoused = resp[6];
- report->ble[V4L2_RDS_BLOCK_A] = 0b11000000 & resp[7];
- report->ble[V4L2_RDS_BLOCK_B] = 0b00110000 & resp[7];
- report->ble[V4L2_RDS_BLOCK_C] = 0b00001100 & resp[7];
- report->ble[V4L2_RDS_BLOCK_D] = 0b00000011 & resp[7];
+ report->ble[V4L2_RDS_BLOCK_A] = 0xc0 & resp[7];
+ report->ble[V4L2_RDS_BLOCK_B] = 0x30 & resp[7];
+ report->ble[V4L2_RDS_BLOCK_C] = 0x0c & resp[7];
+ report->ble[V4L2_RDS_BLOCK_D] = 0x03 & resp[7];
report->rds[V4L2_RDS_BLOCK_A].block = V4L2_RDS_BLOCK_A;
report->rds[V4L2_RDS_BLOCK_A].msb = resp[8];
SI476X_DEFAULT_TIMEOUT);
if (!err) {
- report->expected = be16_to_cpup((__be16 *)(resp + 2));
- report->received = be16_to_cpup((__be16 *)(resp + 4));
- report->uncorrectable = be16_to_cpup((__be16 *)(resp + 6));
+ report->expected = get_unaligned_be16(resp + 2);
+ report->received = get_unaligned_be16(resp + 4);
+ report->uncorrectable = get_unaligned_be16(resp + 6);
}
return err;
{
u8 resp[CMD_FM_PHASE_DIVERSITY_NRESP];
const u8 args[CMD_FM_PHASE_DIVERSITY_NARGS] = {
- mode & 0b111,
+ mode & 0x07,
};
return si476x_core_send_command(core, CMD_FM_PHASE_DIVERSITY,
const int am_freq = tuneargs->freq;
u8 resp[CMD_AM_TUNE_FREQ_NRESP];
const u8 args[CMD_AM_TUNE_FREQ_NARGS] = {
- (tuneargs->zifsr << 6) | (tuneargs->injside & 0b11),
+ (tuneargs->zifsr << 6) | (tuneargs->injside & 0x03),
msb(am_freq),
lsb(am_freq),
};
if (err < 0 || report == NULL)
return err;
- report->multhint = 0b10000000 & resp[1];
- report->multlint = 0b01000000 & resp[1];
- report->snrhint = 0b00001000 & resp[1];
- report->snrlint = 0b00000100 & resp[1];
- report->rssihint = 0b00000010 & resp[1];
- report->rssilint = 0b00000001 & resp[1];
+ report->multhint = 0x80 & resp[1];
+ report->multlint = 0x40 & resp[1];
+ report->snrhint = 0x08 & resp[1];
+ report->snrlint = 0x04 & resp[1];
+ report->rssihint = 0x02 & resp[1];
+ report->rssilint = 0x01 & resp[1];
- report->bltf = 0b10000000 & resp[2];
- report->snr_ready = 0b00100000 & resp[2];
- report->rssiready = 0b00001000 & resp[2];
- report->afcrl = 0b00000010 & resp[2];
- report->valid = 0b00000001 & resp[2];
+ report->bltf = 0x80 & resp[2];
+ report->snr_ready = 0x20 & resp[2];
+ report->rssiready = 0x08 & resp[2];
+ report->afcrl = 0x02 & resp[2];
+ report->valid = 0x01 & resp[2];
- report->readfreq = be16_to_cpup((__be16 *)(resp + 3));
+ report->readfreq = get_unaligned_be16(resp + 3);
report->freqoff = resp[5];
report->rssi = resp[6];
report->snr = resp[7];
report->hassi = resp[10];
report->mult = resp[11];
report->dev = resp[12];
- report->readantcap = be16_to_cpup((__be16 *)(resp + 13));
+ report->readantcap = get_unaligned_be16(resp + 13);
report->assi = resp[15];
report->usn = resp[16];
if (err < 0 || report == NULL)
return err;
- report->multhint = 0b10000000 & resp[1];
- report->multlint = 0b01000000 & resp[1];
- report->snrhint = 0b00001000 & resp[1];
- report->snrlint = 0b00000100 & resp[1];
- report->rssihint = 0b00000010 & resp[1];
- report->rssilint = 0b00000001 & resp[1];
+ report->multhint = 0x80 & resp[1];
+ report->multlint = 0x40 & resp[1];
+ report->snrhint = 0x08 & resp[1];
+ report->snrlint = 0x04 & resp[1];
+ report->rssihint = 0x02 & resp[1];
+ report->rssilint = 0x01 & resp[1];
- report->bltf = 0b10000000 & resp[2];
- report->snr_ready = 0b00100000 & resp[2];
- report->rssiready = 0b00001000 & resp[2];
- report->afcrl = 0b00000010 & resp[2];
- report->valid = 0b00000001 & resp[2];
+ report->bltf = 0x80 & resp[2];
+ report->snr_ready = 0x20 & resp[2];
+ report->rssiready = 0x08 & resp[2];
+ report->afcrl = 0x02 & resp[2];
+ report->valid = 0x01 & resp[2];
- report->readfreq = be16_to_cpup((__be16 *)(resp + 3));
+ report->readfreq = get_unaligned_be16(resp + 3);
report->freqoff = resp[5];
report->rssi = resp[6];
report->snr = resp[7];
report->hassi = resp[10];
report->mult = resp[11];
report->dev = resp[12];
- report->readantcap = be16_to_cpup((__be16 *)(resp + 13));
+ report->readantcap = get_unaligned_be16(resp + 13);
report->assi = resp[15];
report->usn = resp[16];
if (err < 0 || report == NULL)
return err;
- report->multhint = 0b10000000 & resp[1];
- report->multlint = 0b01000000 & resp[1];
- report->snrhint = 0b00001000 & resp[1];
- report->snrlint = 0b00000100 & resp[1];
- report->rssihint = 0b00000010 & resp[1];
- report->rssilint = 0b00000001 & resp[1];
-
- report->bltf = 0b10000000 & resp[2];
- report->snr_ready = 0b00100000 & resp[2];
- report->rssiready = 0b00001000 & resp[2];
- report->injside = 0b00000100 & resp[2];
- report->afcrl = 0b00000010 & resp[2];
- report->valid = 0b00000001 & resp[2];
-
- report->readfreq = be16_to_cpup((__be16 *)(resp + 3));
+ report->multhint = 0x80 & resp[1];
+ report->multlint = 0x40 & resp[1];
+ report->snrhint = 0x08 & resp[1];
+ report->snrlint = 0x04 & resp[1];
+ report->rssihint = 0x02 & resp[1];
+ report->rssilint = 0x01 & resp[1];
+
+ report->bltf = 0x80 & resp[2];
+ report->snr_ready = 0x20 & resp[2];
+ report->rssiready = 0x08 & resp[2];
+ report->injside = 0x04 & resp[2];
+ report->afcrl = 0x02 & resp[2];
+ report->valid = 0x01 & resp[2];
+
+ report->readfreq = get_unaligned_be16(resp + 3);
report->freqoff = resp[5];
report->rssi = resp[6];
report->snr = resp[7];
report->hassi = resp[10];
report->mult = resp[11];
report->dev = resp[12];
- report->readantcap = be16_to_cpup((__be16 *)(resp + 13));
+ report->readantcap = get_unaligned_be16(resp + 13);
report->assi = resp[15];
report->usn = resp[16];
report->rdsdev = resp[18];
report->assidev = resp[19];
report->strongdev = resp[20];
- report->rdspi = be16_to_cpup((__be16 *)(resp + 21));
+ report->rdspi = get_unaligned_be16(resp + 21);
return err;
}
#include <linux/irq.h>
#include <linux/interrupt.h>
-static int irq;
+static int irq = -1;
static irqreturn_t dummy_interrupt(int irq, void *dev_id)
{
static int __init dummy_irq_init(void)
{
+ if (irq < 0) {
+ printk(KERN_ERR "dummy-irq: no IRQ given. Use irq=N\n");
+ return -EIO;
+ }
if (request_irq(irq, &dummy_interrupt, IRQF_SHARED, "dummy_irq", &irq)) {
printk(KERN_ERR "dummy-irq: cannot register IRQ %d\n", irq);
return -EIO;
}
}
+ device->event_cb = NULL;
+
mutex_unlock(&dev->device_lock);
if (!device->ops || !device->ops->disable)
/* find ME client we're trying to connect to */
i = mei_me_cl_by_uuid(dev, &data->in_client_uuid);
- if (i >= 0 && !dev->me_clients[i].props.fixed_address) {
- cl->me_client_id = dev->me_clients[i].client_id;
- cl->state = MEI_FILE_CONNECTING;
+ if (i < 0 || dev->me_clients[i].props.fixed_address) {
+ dev_dbg(&dev->pdev->dev, "Cannot connect to FW Client UUID = %pUl\n",
+ &data->in_client_uuid);
+ rets = -ENODEV;
+ goto end;
}
+ cl->me_client_id = dev->me_clients[i].client_id;
+ cl->state = MEI_FILE_CONNECTING;
+
dev_dbg(&dev->pdev->dev, "Connect to FW Client ID = %d\n",
cl->me_client_id);
dev_dbg(&dev->pdev->dev, "FW Client - Protocol Version = %d\n",
goto end;
}
- if (cl->state != MEI_FILE_CONNECTING) {
- rets = -ENODEV;
- goto end;
- }
-
/* prepare the output buffer */
client = &data->out_client_properties;
rets = mei_cl_connect(cl, file);
end:
- dev_dbg(&dev->pdev->dev, "free connect cb memory.");
return rets;
}
config VMWARE_VMCI
tristate "VMware VMCI Driver"
- depends on X86 && PCI && NET
+ depends on X86 && PCI
help
This is VMware's Virtual Machine Communication Interface. It enables
high-speed communication between host and guest in a virtual
#include <linux/pagemap.h>
#include <linux/sched.h>
#include <linux/slab.h>
-#include <linux/socket.h>
+#include <linux/uio.h>
#include <linux/wait.h>
#include <linux/vmalloc.h>
}
/**
- * bond_3ad_get_active_agg_info - get information of the active aggregator
+ * __bond_3ad_get_active_agg_info - get information of the active aggregator
* @bond: bonding struct to work on
* @ad_info: ad_info struct to fill with the bond's info
*
* Returns: 0 on success
* < 0 on error
*/
-int bond_3ad_get_active_agg_info(struct bonding *bond, struct ad_info *ad_info)
+int __bond_3ad_get_active_agg_info(struct bonding *bond,
+ struct ad_info *ad_info)
{
struct aggregator *aggregator = NULL;
struct port *port;
return -1;
}
+/* Wrapper used to hold bond->lock so no slave manipulation can occur */
+int bond_3ad_get_active_agg_info(struct bonding *bond, struct ad_info *ad_info)
+{
+ int ret;
+
+ read_lock(&bond->lock);
+ ret = __bond_3ad_get_active_agg_info(bond, ad_info);
+ read_unlock(&bond->lock);
+
+ return ret;
+}
+
int bond_3ad_xmit_xor(struct sk_buff *skb, struct net_device *dev)
{
struct slave *slave, *start_at;
struct ad_info ad_info;
int res = 1;
- if (bond_3ad_get_active_agg_info(bond, &ad_info)) {
- pr_debug("%s: Error: bond_3ad_get_active_agg_info failed\n",
+ if (__bond_3ad_get_active_agg_info(bond, &ad_info)) {
+ pr_debug("%s: Error: __bond_3ad_get_active_agg_info failed\n",
dev->name);
goto out;
}
void bond_3ad_adapter_duplex_changed(struct slave *slave);
void bond_3ad_handle_link_change(struct slave *slave, char link);
int bond_3ad_get_active_agg_info(struct bonding *bond, struct ad_info *ad_info);
+int __bond_3ad_get_active_agg_info(struct bonding *bond,
+ struct ad_info *ad_info);
int bond_3ad_xmit_xor(struct sk_buff *skb, struct net_device *dev);
int bond_3ad_lacpdu_recv(const struct sk_buff *skb, struct bonding *bond,
struct slave *slave);
slave->dev->features,
mask);
}
+ features = netdev_add_tso_features(features, mask);
out:
read_unlock(&bond->lock);
{
struct sk_buff *skb;
- pr_debug("arp %d on slave %s: dst %x src %x vid %d\n", arp_op,
- slave_dev->name, dest_ip, src_ip, vlan_id);
+ pr_debug("arp %d on slave %s: dst %pI4 src %pI4 vid %d\n", arp_op,
+ slave_dev->name, &dest_ip, &src_ip, vlan_id);
skb = arp_create(arp_op, ETH_P_ARP, dest_ip, slave_dev, src_ip,
NULL, slave_dev->dev_addr, NULL);
__be32 addr;
if (!targets[i])
break;
- pr_debug("basa: target %x\n", targets[i]);
+ pr_debug("basa: target %pI4\n", &targets[i]);
if (!bond_vlan_used(bond)) {
pr_debug("basa: empty vlan: arp_send\n");
addr = bond_confirm_addr(bond->dev, targets[i], 0);
static int bond_check_params(struct bond_params *params)
{
- int arp_validate_value, fail_over_mac_value, primary_reselect_value;
+ int arp_validate_value, fail_over_mac_value, primary_reselect_value, i;
/*
* Convert string parameters.
arp_interval = BOND_LINK_ARP_INTERV;
}
- for (arp_ip_count = 0;
- (arp_ip_count < BOND_MAX_ARP_TARGETS) && arp_ip_target[arp_ip_count];
- arp_ip_count++) {
+ for (arp_ip_count = 0, i = 0;
+ (arp_ip_count < BOND_MAX_ARP_TARGETS) && arp_ip_target[i]; i++) {
/* not complete check, but should be good enough to
catch mistakes */
- __be32 ip = in_aton(arp_ip_target[arp_ip_count]);
- if (!isdigit(arp_ip_target[arp_ip_count][0]) ||
- ip == 0 || ip == htonl(INADDR_BROADCAST)) {
+ __be32 ip = in_aton(arp_ip_target[i]);
+ if (!isdigit(arp_ip_target[i][0]) || ip == 0 ||
+ ip == htonl(INADDR_BROADCAST)) {
pr_warning("Warning: bad arp_ip_target module parameter (%s), ARP monitoring will not be performed\n",
- arp_ip_target[arp_ip_count]);
+ arp_ip_target[i]);
arp_interval = 0;
} else {
- arp_target[arp_ip_count] = ip;
+ arp_target[arp_ip_count++] = ip;
}
}
if (miimon) {
pr_info("MII link monitoring set to %d ms\n", miimon);
} else if (arp_interval) {
- int i;
-
pr_info("ARP monitoring set to %d ms, validate %s, with %d target(s):",
arp_interval,
arp_validate_tbl[arp_validate_value].modename,
seq_printf(seq, "Aggregator selection policy (ad_select): %s\n",
ad_select_tbl[bond->params.ad_select].modename);
- if (bond_3ad_get_active_agg_info(bond, &ad_info)) {
+ if (__bond_3ad_get_active_agg_info(bond, &ad_info)) {
seq_printf(seq, "bond %s has no active aggregator\n",
bond->dev->name);
} else {
int new_value, ret = count;
struct bonding *bond = to_bond(d);
+ if (!rtnl_trylock())
+ return restart_syscall();
+
if (bond->dev->flags & IFF_UP) {
pr_err("unable to update mode of %s because interface is up.\n",
bond->dev->name);
bond->dev->name, bond_mode_tbl[new_value].modename,
new_value);
out:
+ rtnl_unlock();
return ret;
}
static DEVICE_ATTR(mode, S_IRUGO | S_IWUSR,
}
static DEVICE_ATTR(mii_status, S_IRUGO, bonding_show_mii_status, NULL);
-
/*
* Show current 802.3ad aggregator ID.
*/
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.aggregator_id);
}
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.ports);
}
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.actor_key);
}
if (bond->params.mode == BOND_MODE_8023AD) {
struct ad_info ad_info;
count = sprintf(buf, "%d\n",
- (bond_3ad_get_active_agg_info(bond, &ad_info))
+ bond_3ad_get_active_agg_info(bond, &ad_info)
? 0 : ad_info.partner_key);
}
*/
static void bnx2x_set_pbd_gso(struct sk_buff *skb,
struct eth_tx_parse_bd_e1x *pbd,
+ struct eth_tx_start_bd *tx_start_bd,
u32 xmit_type)
{
pbd->lso_mss = cpu_to_le16(skb_shinfo(skb)->gso_size);
ip_hdr(skb)->daddr,
0, IPPROTO_TCP, 0));
- } else
+ /* GSO on 57710/57711 needs FW to calculate IP checksum */
+ tx_start_bd->bd_flags.as_bitfield |= ETH_TX_BD_FLAGS_IP_CSUM;
+ } else {
pbd->tcp_pseudo_csum =
bswab16(~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
&ipv6_hdr(skb)->daddr,
0, IPPROTO_TCP, 0));
+ }
pbd->global_data |=
cpu_to_le16(ETH_TX_PARSE_BD_E1X_PSEUDO_CS_WITHOUT_LEN);
bnx2x_set_pbd_gso_e2(skb, &pbd_e2_parsing_data,
xmit_type);
else
- bnx2x_set_pbd_gso(skb, pbd_e1x, xmit_type);
+ bnx2x_set_pbd_gso(skb, pbd_e1x, tx_start_bd,
+ xmit_type);
}
/* Set the PBD's parsing_data field if not zero
#define DRV_MODULE_NAME "tg3"
#define TG3_MAJ_NUM 3
-#define TG3_MIN_NUM 131
+#define TG3_MIN_NUM 132
#define DRV_MODULE_VERSION \
__stringify(TG3_MAJ_NUM) "." __stringify(TG3_MIN_NUM)
-#define DRV_MODULE_RELDATE "April 09, 2013"
+#define DRV_MODULE_RELDATE "May 21, 2013"
#define RESET_KIND_SHUTDOWN 0
#define RESET_KIND_INIT 1
return 0;
}
+static bool tg3_phy_power_bug(struct tg3 *tp)
+{
+ switch (tg3_asic_rev(tp)) {
+ case ASIC_REV_5700:
+ case ASIC_REV_5704:
+ return true;
+ case ASIC_REV_5780:
+ if (tp->phy_flags & TG3_PHYFLG_MII_SERDES)
+ return true;
+ return false;
+ case ASIC_REV_5717:
+ if (!tp->pci_fn)
+ return true;
+ return false;
+ case ASIC_REV_5719:
+ case ASIC_REV_5720:
+ if ((tp->phy_flags & TG3_PHYFLG_PHY_SERDES) &&
+ !tp->pci_fn)
+ return true;
+ return false;
+ }
+
+ return false;
+}
+
static void tg3_power_down_phy(struct tg3 *tp, bool do_low_power)
{
u32 val;
/* The PHY should not be powered down on some chips because
* of bugs.
*/
- if (tg3_asic_rev(tp) == ASIC_REV_5700 ||
- tg3_asic_rev(tp) == ASIC_REV_5704 ||
- (tg3_asic_rev(tp) == ASIC_REV_5780 &&
- (tp->phy_flags & TG3_PHYFLG_MII_SERDES)) ||
- (tg3_asic_rev(tp) == ASIC_REV_5717 &&
- !tp->pci_fn))
+ if (tg3_phy_power_bug(tp))
return;
if (tg3_chip_rev(tp) == CHIPREV_5784_AX ||
return (base > 0xffffdcc0) && (base + len + 8 < base);
}
+/* Test for TSO DMA buffers that cross into regions which are within MSS bytes
+ * of any 4GB boundaries: 4G, 8G, etc
+ */
+static inline int tg3_4g_tso_overflow_test(struct tg3 *tp, dma_addr_t mapping,
+ u32 len, u32 mss)
+{
+ if (tg3_asic_rev(tp) == ASIC_REV_5762 && mss) {
+ u32 base = (u32) mapping & 0xffffffff;
+
+ return ((base + len + (mss & 0x3fff)) < base);
+ }
+ return 0;
+}
+
/* Test for DMA addresses > 40-bit */
static inline int tg3_40bit_overflow_test(struct tg3 *tp, dma_addr_t mapping,
int len)
if (tg3_4g_overflow_test(map, len))
hwbug = true;
+ if (tg3_4g_tso_overflow_test(tp, map, len, mss))
+ hwbug = true;
+
if (tg3_40bit_overflow_test(tp, map, len))
hwbug = true;
tg3_halt_cpu(tp, RX_CPU_BASE);
}
+ err = tg3_poll_fw(tp);
+ if (err)
+ return err;
+
tw32(GRC_MODE, tp->grc_mode);
if (tg3_chip_rev_id(tp) == CHIPREV_ID_5705_A0) {
tg3_ape_unlock(tp, TG3_APE_LOCK_GRC);
- err = tg3_poll_fw(tp);
- if (err)
- return err;
-
tg3_mdio_start(tp);
if (tg3_flag(tp, PCI_EXPRESS) &&
status = macb_readl(bp, TSR);
macb_writel(bp, TSR, status);
- macb_writel(bp, ISR, MACB_BIT(TCOMP));
+ if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+ macb_writel(bp, ISR, MACB_BIT(TCOMP));
netdev_vdbg(bp->dev, "macb_tx_interrupt status = 0x%03lx\n",
(unsigned long)status);
* now.
*/
macb_writel(bp, IDR, MACB_RX_INT_FLAGS);
- macb_writel(bp, ISR, MACB_BIT(RCOMP));
+ if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+ macb_writel(bp, ISR, MACB_BIT(RCOMP));
if (napi_schedule_prep(&bp->napi)) {
netdev_vdbg(bp->dev, "scheduling RX softirq\n");
}
}
+/*
+ * Configure peripheral capacities according to integration options used
+ */
+static void macb_configure_caps(struct macb *bp)
+{
+ if (macb_is_gem(bp)) {
+ if (GEM_BF(IRQCOR, gem_readl(bp, DCFG1)) == 0)
+ bp->caps |= MACB_CAPS_ISR_CLEAR_ON_WRITE;
+ }
+}
+
static void macb_init_hw(struct macb *bp)
{
u32 config;
bp->duplex = DUPLEX_HALF;
macb_configure_dma(bp);
+ macb_configure_caps(bp);
/* Initialize TX and RX buffers */
macb_writel(bp, RBQP, bp->rx_ring_dma);
#define MACB_REV_SIZE 16
/* Bitfields in DCFG1. */
+#define GEM_IRQCOR_OFFSET 23
+#define GEM_IRQCOR_SIZE 1
#define GEM_DBWDEF_OFFSET 25
#define GEM_DBWDEF_SIZE 3
#define MACB_MAN_READ 2
#define MACB_MAN_CODE 2
+/* Capability mask bits */
+#define MACB_CAPS_ISR_CLEAR_ON_WRITE 0x1
+
/* Bit manipulation macros */
#define MACB_BIT(name) \
(1 << MACB_##name##_OFFSET)
unsigned int speed;
unsigned int duplex;
+ u32 caps;
+
phy_interface_t phy_interface;
/* AT91RM9200 transmit */
for (i = 0; i < desc_count; i++) {
desc->desc_len = desc->desc_len ? : RESOURCE_DESC_SIZE;
if (((void *)desc + desc->desc_len) >
- (void *)(buf + max_buf_size)) {
- desc = NULL;
- break;
- }
+ (void *)(buf + max_buf_size))
+ return NULL;
if (desc->desc_type == NIC_RESOURCE_DESC_TYPE_V0 ||
desc->desc_type == NIC_RESOURCE_DESC_TYPE_V1)
- break;
+ return desc;
desc = (void *)desc + desc->desc_len;
}
- if (!desc || i == MAX_RESOURCE_DESC)
- return NULL;
-
- return desc;
+ return NULL;
}
/* Uses Mbox */
if (unlikely(!skb))
return skb;
- if (vlan_tx_tag_present(skb)) {
+ if (vlan_tx_tag_present(skb))
vlan_tag = be_get_tx_vlan_tag(adapter, skb);
- skb = __vlan_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
- if (skb)
- skb->vlan_tci = 0;
- }
-
- if (qnq_async_evt_rcvd(adapter) && adapter->pvid) {
- if (!vlan_tag)
- vlan_tag = adapter->pvid;
- if (skip_hw_vlan)
- *skip_hw_vlan = true;
- }
+ else if (qnq_async_evt_rcvd(adapter) && adapter->pvid)
+ vlan_tag = adapter->pvid;
if (vlan_tag) {
skb = __vlan_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
if (unlikely(!skb))
return skb;
-
skb->vlan_tci = 0;
+ if (skip_hw_vlan)
+ *skip_hw_vlan = true;
}
/* Insert the outer VLAN, if any */
.driver_data = FEC_QUIRK_ENET_MAC | FEC_QUIRK_HAS_GBIT |
FEC_QUIRK_HAS_BUFDESC_EX | FEC_QUIRK_HAS_CSUM,
}, {
- .name = "mvf-fec",
+ .name = "mvf600-fec",
.driver_data = FEC_QUIRK_ENET_MAC,
}, {
/* sentinel */
IMX27_FEC, /* runs on i.mx27/35/51 */
IMX28_FEC,
IMX6Q_FEC,
- MVF_FEC,
+ MVF600_FEC,
};
static const struct of_device_id fec_dt_ids[] = {
{ .compatible = "fsl,imx27-fec", .data = &fec_devtype[IMX27_FEC], },
{ .compatible = "fsl,imx28-fec", .data = &fec_devtype[IMX28_FEC], },
{ .compatible = "fsl,imx6q-fec", .data = &fec_devtype[IMX6Q_FEC], },
- { .compatible = "fsl,mvf-fec", .data = &fec_devtype[MVF_FEC], },
+ { .compatible = "fsl,mvf600-fec", .data = &fec_devtype[MVF600_FEC], },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, fec_dt_ids);
netif_device_detach(ndev);
napi_disable(&fep->napi);
netif_stop_queue(ndev);
- netif_tx_lock(ndev);
+ netif_tx_lock_bh(ndev);
}
/* Whack a reset. We should wait for this. */
writel(FEC_DEFAULT_IMASK, fep->hwp + FEC_IMASK);
if (netif_running(ndev)) {
- netif_device_attach(ndev);
- napi_enable(&fep->napi);
+ netif_tx_unlock_bh(ndev);
netif_wake_queue(ndev);
- netif_tx_unlock(ndev);
+ napi_enable(&fep->napi);
+ netif_device_attach(ndev);
}
}
return 0;
no_clock:
+ iounmap(etsects->regs);
no_ioremap:
release_resource(etsects->rsrc);
no_resource:
/* TFD data structure masks. */
/* TFDList, TFC */
-#define IPG_TFC_RSVD_MASK 0x0000FFFF9FFFFFFF
-#define IPG_TFC_FRAMEID 0x000000000000FFFF
-#define IPG_TFC_WORDALIGN 0x0000000000030000
-#define IPG_TFC_WORDALIGNTODWORD 0x0000000000000000
-#define IPG_TFC_WORDALIGNTOWORD 0x0000000000020000
-#define IPG_TFC_WORDALIGNDISABLED 0x0000000000030000
-#define IPG_TFC_TCPCHECKSUMENABLE 0x0000000000040000
-#define IPG_TFC_UDPCHECKSUMENABLE 0x0000000000080000
-#define IPG_TFC_IPCHECKSUMENABLE 0x0000000000100000
-#define IPG_TFC_FCSAPPENDDISABLE 0x0000000000200000
-#define IPG_TFC_TXINDICATE 0x0000000000400000
-#define IPG_TFC_TXDMAINDICATE 0x0000000000800000
-#define IPG_TFC_FRAGCOUNT 0x000000000F000000
-#define IPG_TFC_VLANTAGINSERT 0x0000000010000000
-#define IPG_TFC_TFDDONE 0x0000000080000000
-#define IPG_TFC_VID 0x00000FFF00000000
-#define IPG_TFC_CFI 0x0000100000000000
-#define IPG_TFC_USERPRIORITY 0x0000E00000000000
+#define IPG_TFC_RSVD_MASK 0x0000FFFF9FFFFFFFULL
+#define IPG_TFC_FRAMEID 0x000000000000FFFFULL
+#define IPG_TFC_WORDALIGN 0x0000000000030000ULL
+#define IPG_TFC_WORDALIGNTODWORD 0x0000000000000000ULL
+#define IPG_TFC_WORDALIGNTOWORD 0x0000000000020000ULL
+#define IPG_TFC_WORDALIGNDISABLED 0x0000000000030000ULL
+#define IPG_TFC_TCPCHECKSUMENABLE 0x0000000000040000ULL
+#define IPG_TFC_UDPCHECKSUMENABLE 0x0000000000080000ULL
+#define IPG_TFC_IPCHECKSUMENABLE 0x0000000000100000ULL
+#define IPG_TFC_FCSAPPENDDISABLE 0x0000000000200000ULL
+#define IPG_TFC_TXINDICATE 0x0000000000400000ULL
+#define IPG_TFC_TXDMAINDICATE 0x0000000000800000ULL
+#define IPG_TFC_FRAGCOUNT 0x000000000F000000ULL
+#define IPG_TFC_VLANTAGINSERT 0x0000000010000000ULL
+#define IPG_TFC_TFDDONE 0x0000000080000000ULL
+#define IPG_TFC_VID 0x00000FFF00000000ULL
+#define IPG_TFC_CFI 0x0000100000000000ULL
+#define IPG_TFC_USERPRIORITY 0x0000E00000000000ULL
/* TFDList, FragInfo */
-#define IPG_TFI_RSVD_MASK 0xFFFF00FFFFFFFFFF
-#define IPG_TFI_FRAGADDR 0x000000FFFFFFFFFF
-#define IPG_TFI_FRAGLEN 0xFFFF000000000000LL
+#define IPG_TFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
+#define IPG_TFI_FRAGADDR 0x000000FFFFFFFFFFULL
+#define IPG_TFI_FRAGLEN 0xFFFF000000000000ULL
/* RFD data structure masks. */
/* RFDList, RFS */
-#define IPG_RFS_RSVD_MASK 0x0000FFFFFFFFFFFF
-#define IPG_RFS_RXFRAMELEN 0x000000000000FFFF
-#define IPG_RFS_RXFIFOOVERRUN 0x0000000000010000
-#define IPG_RFS_RXRUNTFRAME 0x0000000000020000
-#define IPG_RFS_RXALIGNMENTERROR 0x0000000000040000
-#define IPG_RFS_RXFCSERROR 0x0000000000080000
-#define IPG_RFS_RXOVERSIZEDFRAME 0x0000000000100000
-#define IPG_RFS_RXLENGTHERROR 0x0000000000200000
-#define IPG_RFS_VLANDETECTED 0x0000000000400000
-#define IPG_RFS_TCPDETECTED 0x0000000000800000
-#define IPG_RFS_TCPERROR 0x0000000001000000
-#define IPG_RFS_UDPDETECTED 0x0000000002000000
-#define IPG_RFS_UDPERROR 0x0000000004000000
-#define IPG_RFS_IPDETECTED 0x0000000008000000
-#define IPG_RFS_IPERROR 0x0000000010000000
-#define IPG_RFS_FRAMESTART 0x0000000020000000
-#define IPG_RFS_FRAMEEND 0x0000000040000000
-#define IPG_RFS_RFDDONE 0x0000000080000000
-#define IPG_RFS_TCI 0x0000FFFF00000000
+#define IPG_RFS_RSVD_MASK 0x0000FFFFFFFFFFFFULL
+#define IPG_RFS_RXFRAMELEN 0x000000000000FFFFULL
+#define IPG_RFS_RXFIFOOVERRUN 0x0000000000010000ULL
+#define IPG_RFS_RXRUNTFRAME 0x0000000000020000ULL
+#define IPG_RFS_RXALIGNMENTERROR 0x0000000000040000ULL
+#define IPG_RFS_RXFCSERROR 0x0000000000080000ULL
+#define IPG_RFS_RXOVERSIZEDFRAME 0x0000000000100000ULL
+#define IPG_RFS_RXLENGTHERROR 0x0000000000200000ULL
+#define IPG_RFS_VLANDETECTED 0x0000000000400000ULL
+#define IPG_RFS_TCPDETECTED 0x0000000000800000ULL
+#define IPG_RFS_TCPERROR 0x0000000001000000ULL
+#define IPG_RFS_UDPDETECTED 0x0000000002000000ULL
+#define IPG_RFS_UDPERROR 0x0000000004000000ULL
+#define IPG_RFS_IPDETECTED 0x0000000008000000ULL
+#define IPG_RFS_IPERROR 0x0000000010000000ULL
+#define IPG_RFS_FRAMESTART 0x0000000020000000ULL
+#define IPG_RFS_FRAMEEND 0x0000000040000000ULL
+#define IPG_RFS_RFDDONE 0x0000000080000000ULL
+#define IPG_RFS_TCI 0x0000FFFF00000000ULL
/* RFDList, FragInfo */
-#define IPG_RFI_RSVD_MASK 0xFFFF00FFFFFFFFFF
-#define IPG_RFI_FRAGADDR 0x000000FFFFFFFFFF
-#define IPG_RFI_FRAGLEN 0xFFFF000000000000LL
+#define IPG_RFI_RSVD_MASK 0xFFFF00FFFFFFFFFFULL
+#define IPG_RFI_FRAGADDR 0x000000FFFFFFFFFFULL
+#define IPG_RFI_FRAGLEN 0xFFFF000000000000ULL
/* I/O Register masks. */
struct netdev_queue *nq = netdev_get_tx_queue(mp->dev, txq->index);
int reclaimed;
- __netif_tx_lock(nq, smp_processor_id());
+ __netif_tx_lock_bh(nq);
reclaimed = 0;
while (reclaimed < budget && txq->tx_desc_count > 0) {
dev_kfree_skb(skb);
}
- __netif_tx_unlock(nq);
+ __netif_tx_unlock_bh(nq);
if (reclaimed < budget)
mp->work_tx &= ~(1 << txq->index);
INIT_WORK(&mp->tx_timeout_task, tx_timeout_task);
- netif_napi_add(dev, &mp->napi, mv643xx_eth_poll, 128);
+ netif_napi_add(dev, &mp->napi, mv643xx_eth_poll, NAPI_POLL_WEIGHT);
init_timer(&mp->rx_oom);
mp->rx_oom.data = (unsigned long)mp;
#define QLCNIC_FW_HANG 0x4000
#define QLCNIC_FW_LRO_MSS_CAP 0x8000
#define QLCNIC_TX_INTR_SHARED 0x10000
+#define QLCNIC_APP_CHANGED_FLAGS 0x20000
#define QLCNIC_IS_MSI_FAMILY(adapter) \
((adapter)->flags & (QLCNIC_MSI_ENABLED | QLCNIC_MSIX_ENABLED))
+#define QLCNIC_IS_TSO_CAPABLE(adapter) \
+ ((adapter)->ahw->capabilities & QLCNIC_FW_CAPABILITY_TSO)
#define QLCNIC_DEF_NUM_STS_DESC_RINGS 4
#define QLCNIC_MSIX_TBL_SPACE 8192
spinlock_t rx_mac_learn_lock;
u32 file_prd_off; /*File fw product offset*/
u32 fw_version;
+ u32 offload_flags;
const struct firmware *fw;
};
int qlcnic_83xx_configure_opmode(struct qlcnic_adapter *adapter);
int qlcnic_read_mac_addr(struct qlcnic_adapter *);
int qlcnic_setup_netdev(struct qlcnic_adapter *, struct net_device *, int);
+void qlcnic_set_netdev_features(struct qlcnic_adapter *,
+ struct qlcnic_esw_func_cfg *);
void qlcnic_sriov_vf_schedule_multi(struct net_device *);
void qlcnic_vf_add_mc_list(struct net_device *, u16);
clear_bit(__QLCNIC_RESETTING, &adapter->state);
dev_err(&adapter->pdev->dev, "%s:\n", __func__);
- adapter->netdev->trans_start = jiffies;
-
return 0;
}
return rc;
}
+static netdev_features_t qlcnic_process_flags(struct qlcnic_adapter *adapter,
+ netdev_features_t features)
+{
+ u32 offload_flags = adapter->offload_flags;
+
+ if (offload_flags & BIT_0) {
+ features |= NETIF_F_RXCSUM | NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM;
+ adapter->rx_csum = 1;
+ if (QLCNIC_IS_TSO_CAPABLE(adapter)) {
+ if (!(offload_flags & BIT_1))
+ features &= ~NETIF_F_TSO;
+ else
+ features |= NETIF_F_TSO;
+
+ if (!(offload_flags & BIT_2))
+ features &= ~NETIF_F_TSO6;
+ else
+ features |= NETIF_F_TSO6;
+ }
+ } else {
+ features &= ~(NETIF_F_RXCSUM |
+ NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM);
+
+ if (QLCNIC_IS_TSO_CAPABLE(adapter))
+ features &= ~(NETIF_F_TSO | NETIF_F_TSO6);
+ adapter->rx_csum = 0;
+ }
+
+ return features;
+}
netdev_features_t qlcnic_fix_features(struct net_device *netdev,
netdev_features_t features)
{
struct qlcnic_adapter *adapter = netdev_priv(netdev);
+ netdev_features_t changed;
- if ((adapter->flags & QLCNIC_ESWITCH_ENABLED) &&
- qlcnic_82xx_check(adapter)) {
- netdev_features_t changed = features ^ netdev->features;
- features ^= changed & (NETIF_F_ALL_CSUM | NETIF_F_RXCSUM);
+ if (qlcnic_82xx_check(adapter) &&
+ (adapter->flags & QLCNIC_ESWITCH_ENABLED)) {
+ if (adapter->flags & QLCNIC_APP_CHANGED_FLAGS) {
+ features = qlcnic_process_flags(adapter, features);
+ } else {
+ changed = features ^ netdev->features;
+ features ^= changed & (NETIF_F_RXCSUM |
+ NETIF_F_IP_CSUM |
+ NETIF_F_IPV6_CSUM |
+ NETIF_F_TSO |
+ NETIF_F_TSO6);
+ }
}
if (!(features & NETIF_F_RXCSUM))
static void qlcnic_free_lb_filters_mem(struct qlcnic_adapter *adapter);
static void qlcnic_dev_set_npar_ready(struct qlcnic_adapter *);
static int qlcnicvf_start_firmware(struct qlcnic_adapter *);
-static void qlcnic_set_netdev_features(struct qlcnic_adapter *,
- struct qlcnic_esw_func_cfg *);
static int qlcnic_vlan_rx_add(struct net_device *, __be16, u16);
static int qlcnic_vlan_rx_del(struct net_device *, __be16, u16);
-#define QLCNIC_IS_TSO_CAPABLE(adapter) \
- ((adapter)->ahw->capabilities & QLCNIC_FW_CAPABILITY_TSO)
-
static u32 qlcnic_vlan_tx_check(struct qlcnic_adapter *adapter)
{
struct qlcnic_hardware_context *ahw = adapter->ahw;
if (!esw_cfg->promisc_mode)
adapter->flags |= QLCNIC_PROMISC_DISABLED;
-
- qlcnic_set_netdev_features(adapter, esw_cfg);
}
int qlcnic_set_eswitch_port_config(struct qlcnic_adapter *adapter)
return -EIO;
qlcnic_set_vlan_config(adapter, &esw_cfg);
qlcnic_set_eswitch_port_features(adapter, &esw_cfg);
+ qlcnic_set_netdev_features(adapter, &esw_cfg);
return 0;
}
-static void
-qlcnic_set_netdev_features(struct qlcnic_adapter *adapter,
- struct qlcnic_esw_func_cfg *esw_cfg)
+void qlcnic_set_netdev_features(struct qlcnic_adapter *adapter,
+ struct qlcnic_esw_func_cfg *esw_cfg)
{
struct net_device *netdev = adapter->netdev;
- unsigned long features, vlan_features;
if (qlcnic_83xx_check(adapter))
return;
- features = (NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_RXCSUM |
- NETIF_F_IPV6_CSUM | NETIF_F_GRO);
- vlan_features = (NETIF_F_SG | NETIF_F_IP_CSUM |
- NETIF_F_IPV6_CSUM);
-
- if (QLCNIC_IS_TSO_CAPABLE(adapter)) {
- features |= (NETIF_F_TSO | NETIF_F_TSO6);
- vlan_features |= (NETIF_F_TSO | NETIF_F_TSO6);
- }
-
- if (netdev->features & NETIF_F_LRO)
- features |= NETIF_F_LRO;
-
- if (esw_cfg->offload_flags & BIT_0) {
- netdev->features |= features;
- adapter->rx_csum = 1;
- if (!(esw_cfg->offload_flags & BIT_1)) {
- netdev->features &= ~NETIF_F_TSO;
- features &= ~NETIF_F_TSO;
- }
- if (!(esw_cfg->offload_flags & BIT_2)) {
- netdev->features &= ~NETIF_F_TSO6;
- features &= ~NETIF_F_TSO6;
- }
- } else {
- netdev->features &= ~features;
- features &= ~features;
- adapter->rx_csum = 0;
- }
-
- netdev->vlan_features = (features & vlan_features);
+ adapter->offload_flags = esw_cfg->offload_flags;
+ adapter->flags |= QLCNIC_APP_CHANGED_FLAGS;
+ netdev_update_features(netdev);
+ adapter->flags &= ~QLCNIC_APP_CHANGED_FLAGS;
}
static int
pci_enable_pcie_error_reporting(pdev);
ahw = kzalloc(sizeof(struct qlcnic_hardware_context), GFP_KERNEL);
- if (!ahw)
+ if (!ahw) {
+ err = -ENOMEM;
goto err_out_free_res;
+ }
switch (ent->device) {
case PCI_DEVICE_ID_QLOGIC_QLE824X:
adapter->qlcnic_wq = create_singlethread_workqueue("qlcnic");
if (adapter->qlcnic_wq == NULL) {
+ err = -ENOMEM;
dev_err(&pdev->dev, "Failed to create workqueue\n");
goto err_out_free_netdev;
}
goto err_out_disable_msi;
}
+ err = qlcnic_get_act_pci_func(adapter);
+ if (err)
+ goto err_out_disable_mbx_intr;
+
err = qlcnic_setup_netdev(adapter, netdev, pci_using_dac);
if (err)
goto err_out_disable_mbx_intr;
break;
}
- if (qlcnic_get_act_pci_func(adapter))
- goto err_out_disable_mbx_intr;
-
if (adapter->drv_mac_learn)
qlcnic_alloc_lb_filters_mem(adapter);
if (adapter->need_fw_reset)
goto detach;
- if (adapter->ahw->reset_context && qlcnic_auto_fw_reset) {
+ if (adapter->ahw->reset_context && qlcnic_auto_fw_reset)
qlcnic_reset_hw_context(adapter);
- adapter->netdev->trans_start = jiffies;
- }
return 0;
}
if (!qlcnic_sriov_vf_reinit_driver(adapter)) {
qlcnic_sriov_vf_attach(adapter);
- adapter->netdev->trans_start = jiffies;
adapter->tx_timeo_cnt = 0;
adapter->reset_ctx_cnt = 0;
adapter->fw_fail_cnt = 0;
switch (esw_cfg[i].op_mode) {
case QLCNIC_PORT_DEFAULTS:
qlcnic_set_eswitch_port_features(adapter, &esw_cfg[i]);
+ rtnl_lock();
+ qlcnic_set_netdev_features(adapter, &esw_cfg[i]);
+ rtnl_unlock();
break;
case QLCNIC_ADD_VLAN:
qlcnic_set_vlan_config(adapter, &esw_cfg[i]);
cp->dev->stats.tx_dropped++;
}
}
+ netdev_reset_queue(cp->dev);
memset(cp->rx_ring, 0, sizeof(struct cp_desc) * CP_RX_RING_SIZE);
memset(cp->tx_ring, 0, sizeof(struct cp_desc) * CP_TX_RING_SIZE);
return -EIO;
}
-static inline void rtl8169_tso_csum(struct rtl8169_private *tp,
+static bool rtl_skb_pad(struct sk_buff *skb)
+{
+ if (skb_padto(skb, ETH_ZLEN))
+ return false;
+ skb_put(skb, ETH_ZLEN - skb->len);
+ return true;
+}
+
+static bool rtl_test_hw_pad_bug(struct rtl8169_private *tp, struct sk_buff *skb)
+{
+ return skb->len < ETH_ZLEN && tp->mac_version == RTL_GIGA_MAC_VER_34;
+}
+
+static inline bool rtl8169_tso_csum(struct rtl8169_private *tp,
struct sk_buff *skb, u32 *opts)
{
const struct rtl_tx_desc_info *info = tx_desc_info + tp->txd_version;
} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
const struct iphdr *ip = ip_hdr(skb);
+ if (unlikely(rtl_test_hw_pad_bug(tp, skb)))
+ return skb_checksum_help(skb) == 0 && rtl_skb_pad(skb);
+
if (ip->protocol == IPPROTO_TCP)
opts[offset] |= info->checksum.tcp;
else if (ip->protocol == IPPROTO_UDP)
opts[offset] |= info->checksum.udp;
else
WARN_ON_ONCE(1);
+ } else {
+ if (unlikely(rtl_test_hw_pad_bug(tp, skb)))
+ return rtl_skb_pad(skb);
}
+ return true;
}
static netdev_tx_t rtl8169_start_xmit(struct sk_buff *skb,
goto err_stop_0;
}
- /* 8168evl does not automatically pad to minimum length. */
- if (unlikely(tp->mac_version == RTL_GIGA_MAC_VER_34 &&
- skb->len < ETH_ZLEN)) {
- if (skb_padto(skb, ETH_ZLEN))
- goto err_update_stats;
- skb_put(skb, ETH_ZLEN - skb->len);
- }
-
if (unlikely(le32_to_cpu(txd->opts1) & DescOwn))
goto err_stop_0;
+ opts[1] = cpu_to_le32(rtl8169_tx_vlan_tag(skb));
+ opts[0] = DescOwn;
+
+ if (!rtl8169_tso_csum(tp, skb, opts))
+ goto err_update_stats;
+
len = skb_headlen(skb);
mapping = dma_map_single(d, skb->data, len, DMA_TO_DEVICE);
if (unlikely(dma_mapping_error(d, mapping))) {
tp->tx_skb[entry].len = len;
txd->addr = cpu_to_le64(mapping);
- opts[1] = cpu_to_le32(rtl8169_tx_vlan_tag(skb));
- opts[0] = DescOwn;
-
- rtl8169_tso_csum(tp, skb, opts);
-
frags = rtl8169_xmit_frags(tp, skb, opts);
if (frags < 0)
goto err_dma_1;
EFX_MAX_FRAME_LEN(efx->net_dev->mtu) +
efx->type->rx_buffer_padding);
rx_buf_len = (sizeof(struct efx_rx_page_state) +
- EFX_PAGE_IP_ALIGN + efx->rx_dma_len);
+ NET_IP_ALIGN + efx->rx_dma_len);
if (rx_buf_len <= PAGE_SIZE) {
efx->rx_scatter = false;
efx->rx_buffer_order = 0;
} else if (efx->type->can_rx_scatter) {
+ BUILD_BUG_ON(EFX_RX_USR_BUF_SIZE % L1_CACHE_BYTES);
BUILD_BUG_ON(sizeof(struct efx_rx_page_state) +
- EFX_PAGE_IP_ALIGN + EFX_RX_USR_BUF_SIZE >
- PAGE_SIZE / 2);
+ 2 * ALIGN(NET_IP_ALIGN + EFX_RX_USR_BUF_SIZE,
+ EFX_RX_BUF_ALIGNMENT) >
+ PAGE_SIZE);
efx->rx_scatter = true;
efx->rx_dma_len = EFX_RX_USR_BUF_SIZE;
efx->rx_buffer_order = 0;
/* Maximum possible MTU the driver supports */
#define EFX_MAX_MTU (9 * 1024)
-/* Size of an RX scatter buffer. Small enough to pack 2 into a 4K page. */
-#define EFX_RX_USR_BUF_SIZE 1824
+/* Size of an RX scatter buffer. Small enough to pack 2 into a 4K page,
+ * and should be a multiple of the cache line size.
+ */
+#define EFX_RX_USR_BUF_SIZE (2048 - 256)
+
+/* If possible, we should ensure cache line alignment at start and end
+ * of every buffer. Otherwise, we just need to ensure 4-byte
+ * alignment of the network header.
+ */
+#if NET_IP_ALIGN == 0
+#define EFX_RX_BUF_ALIGNMENT L1_CACHE_BYTES
+#else
+#define EFX_RX_BUF_ALIGNMENT 4
+#endif
/* Forward declare Precision Time Protocol (PTP) support structure. */
struct efx_ptp_data;
STATE_RECOVERY = 3, /* device recovering from PCI error */
};
-/*
- * Alignment of page-allocated RX buffers
- *
- * Controls the number of bytes inserted at the start of an RX buffer.
- * This is the equivalent of NET_IP_ALIGN [which controls the alignment
- * of the skb->head for hardware DMA].
- */
-#ifdef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
-#define EFX_PAGE_IP_ALIGN 0
-#else
-#define EFX_PAGE_IP_ALIGN NET_IP_ALIGN
-#endif
-
/*
* Alignment of the skb->head which wraps a page-allocated RX buffer
*
* The skb allocated to wrap an rx_buffer can have this alignment. Since
* the data is memcpy'd from the rx_buf, it does not need to be equal to
- * EFX_PAGE_IP_ALIGN.
+ * NET_IP_ALIGN.
*/
#define EFX_PAGE_SKB_ALIGN 2
void efx_rx_config_page_split(struct efx_nic *efx)
{
- efx->rx_page_buf_step = ALIGN(efx->rx_dma_len + EFX_PAGE_IP_ALIGN,
- L1_CACHE_BYTES);
+ efx->rx_page_buf_step = ALIGN(efx->rx_dma_len + NET_IP_ALIGN,
+ EFX_RX_BUF_ALIGNMENT);
efx->rx_bufs_per_page = efx->rx_buffer_order ? 1 :
((PAGE_SIZE - sizeof(struct efx_rx_page_state)) /
efx->rx_page_buf_step);
do {
index = rx_queue->added_count & rx_queue->ptr_mask;
rx_buf = efx_rx_buffer(rx_queue, index);
- rx_buf->dma_addr = dma_addr + EFX_PAGE_IP_ALIGN;
+ rx_buf->dma_addr = dma_addr + NET_IP_ALIGN;
rx_buf->page = page;
- rx_buf->page_offset = page_offset + EFX_PAGE_IP_ALIGN;
+ rx_buf->page_offset = page_offset + NET_IP_ALIGN;
rx_buf->len = efx->rx_dma_len;
rx_buf->flags = 0;
++rx_queue->added_count;
{QMI_FIXED_INTF(0x1bbb, 0x011e, 4)}, /* Telekom Speedstick LTE II (Alcatel One Touch L100V LTE) */
{QMI_FIXED_INTF(0x2357, 0x0201, 4)}, /* TP-LINK HSUPA Modem MA180 */
{QMI_FIXED_INTF(0x1bc7, 0x1200, 5)}, /* Telit LE920 */
+ {QMI_FIXED_INTF(0x1e2d, 0x12d1, 4)}, /* Cinterion PLxx */
/* 4. Gobi 1000 devices */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */
struct usb_device *udev;
struct tasklet_struct tl;
struct net_device *netdev;
- struct urb *rx_urb, *tx_urb, *intr_urb, *ctrl_urb;
+ struct urb *rx_urb, *tx_urb, *intr_urb;
struct sk_buff *tx_skb, *rx_skb;
struct sk_buff *rx_skb_pool[RX_SKB_POOL_SIZE];
spinlock_t rx_pool_lock;
struct usb_ctrlrequest dr;
int intr_interval;
- __le16 rx_creg;
u8 *intr_buff;
u8 phy;
};
typedef struct rtl8150 rtl8150_t;
+struct async_req {
+ struct usb_ctrlrequest dr;
+ u16 rx_creg;
+};
+
static const char driver_name [] = "rtl8150";
/*
indx, 0, data, size, 500);
}
-static void ctrl_callback(struct urb *urb)
+static void async_set_reg_cb(struct urb *urb)
{
- rtl8150_t *dev;
+ struct async_req *req = (struct async_req *)urb->context;
int status = urb->status;
- switch (status) {
- case 0:
- break;
- case -EINPROGRESS:
- break;
- case -ENOENT:
- break;
- default:
- if (printk_ratelimit())
- dev_warn(&urb->dev->dev, "ctrl urb status %d\n", status);
- }
- dev = urb->context;
- clear_bit(RX_REG_SET, &dev->flags);
+ if (status < 0)
+ dev_dbg(&urb->dev->dev, "%s failed with %d", __func__, status);
+ kfree(req);
+ usb_free_urb(urb);
}
-static int async_set_registers(rtl8150_t * dev, u16 indx, u16 size)
+static int async_set_registers(rtl8150_t *dev, u16 indx, u16 size, u16 reg)
{
- int ret;
-
- if (test_bit(RX_REG_SET, &dev->flags))
- return -EAGAIN;
+ int res = -ENOMEM;
+ struct urb *async_urb;
+ struct async_req *req;
- dev->dr.bRequestType = RTL8150_REQT_WRITE;
- dev->dr.bRequest = RTL8150_REQ_SET_REGS;
- dev->dr.wValue = cpu_to_le16(indx);
- dev->dr.wIndex = 0;
- dev->dr.wLength = cpu_to_le16(size);
- dev->ctrl_urb->transfer_buffer_length = size;
- usb_fill_control_urb(dev->ctrl_urb, dev->udev,
- usb_sndctrlpipe(dev->udev, 0), (char *) &dev->dr,
- &dev->rx_creg, size, ctrl_callback, dev);
- if ((ret = usb_submit_urb(dev->ctrl_urb, GFP_ATOMIC))) {
- if (ret == -ENODEV)
+ req = kmalloc(sizeof(struct async_req), GFP_ATOMIC);
+ if (req == NULL)
+ return res;
+ async_urb = usb_alloc_urb(0, GFP_ATOMIC);
+ if (async_urb == NULL) {
+ kfree(req);
+ return res;
+ }
+ req->rx_creg = cpu_to_le16(reg);
+ req->dr.bRequestType = RTL8150_REQT_WRITE;
+ req->dr.bRequest = RTL8150_REQ_SET_REGS;
+ req->dr.wIndex = 0;
+ req->dr.wValue = cpu_to_le16(indx);
+ req->dr.wLength = cpu_to_le16(size);
+ usb_fill_control_urb(async_urb, dev->udev,
+ usb_sndctrlpipe(dev->udev, 0), (void *)&req->dr,
+ &req->rx_creg, size, async_set_reg_cb, req);
+ res = usb_submit_urb(async_urb, GFP_ATOMIC);
+ if (res) {
+ if (res == -ENODEV)
netif_device_detach(dev->netdev);
- dev_err(&dev->udev->dev,
- "control request submission failed: %d\n", ret);
- } else
- set_bit(RX_REG_SET, &dev->flags);
-
- return ret;
+ dev_err(&dev->udev->dev, "%s failed with %d\n", __func__, res);
+ }
+ return res;
}
static int read_mii_word(rtl8150_t * dev, u8 phy, __u8 indx, u16 * reg)
usb_free_urb(dev->tx_urb);
return 0;
}
- dev->ctrl_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->ctrl_urb) {
- usb_free_urb(dev->rx_urb);
- usb_free_urb(dev->tx_urb);
- usb_free_urb(dev->intr_urb);
- return 0;
- }
return 1;
}
usb_free_urb(dev->rx_urb);
usb_free_urb(dev->tx_urb);
usb_free_urb(dev->intr_urb);
- usb_free_urb(dev->ctrl_urb);
}
static void unlink_all_urbs(rtl8150_t * dev)
usb_kill_urb(dev->rx_urb);
usb_kill_urb(dev->tx_urb);
usb_kill_urb(dev->intr_urb);
- usb_kill_urb(dev->ctrl_urb);
}
static inline struct sk_buff *pull_skb(rtl8150_t *dev)
}
/* RCR bit7=1 attach Rx info at the end; =0 HW CRC (which is broken) */
rcr = 0x9e;
- dev->rx_creg = cpu_to_le16(rcr);
tcr = 0xd8;
cr = 0x0c;
if (!(rcr & 0x80))
static void rtl8150_set_multicast(struct net_device *netdev)
{
rtl8150_t *dev = netdev_priv(netdev);
+ u16 rx_creg = 0x9e;
+
netif_stop_queue(netdev);
if (netdev->flags & IFF_PROMISC) {
- dev->rx_creg |= cpu_to_le16(0x0001);
+ rx_creg |= 0x0001;
dev_info(&netdev->dev, "%s: promiscuous mode\n", netdev->name);
} else if (!netdev_mc_empty(netdev) ||
(netdev->flags & IFF_ALLMULTI)) {
- dev->rx_creg &= cpu_to_le16(0xfffe);
- dev->rx_creg |= cpu_to_le16(0x0002);
+ rx_creg &= 0xfffe;
+ rx_creg |= 0x0002;
dev_info(&netdev->dev, "%s: allmulti set\n", netdev->name);
} else {
/* ~RX_MULTICAST, ~RX_PROMISCUOUS */
- dev->rx_creg &= cpu_to_le16(0x00fc);
+ rx_creg &= 0x00fc;
}
- async_set_registers(dev, RCR, 2);
+ async_set_registers(dev, RCR, sizeof(rx_creg), rx_creg);
netif_wake_queue(netdev);
}
/* usbnet already took usb runtime pm, so have to enable the feature
* for usb interface, otherwise usb_autopm_get_interface may return
- * failure if USB_SUSPEND(RUNTIME_PM) is enabled.
+ * failure if RUNTIME_PM is enabled.
*/
if (!driver->supports_autosuspend) {
driver->supports_autosuspend = 1;
struct virtnet_info *vi = netdev_priv(dev);
int i;
- for (i = 0; i < vi->curr_queue_pairs; i++) {
- /* Make sure we have some buffers: if oom use wq. */
- if (!try_fill_recv(&vi->rq[i], GFP_KERNEL))
- schedule_delayed_work(&vi->refill, 0);
+ for (i = 0; i < vi->max_queue_pairs; i++) {
+ if (i < vi->curr_queue_pairs)
+ /* Make sure we have some buffers: if oom use wq. */
+ if (!try_fill_recv(&vi->rq[i], GFP_KERNEL))
+ schedule_delayed_work(&vi->refill, 0);
virtnet_napi_enable(&vi->rq[i]);
}
}
/* Look up Ethernet address in forwarding table */
-static struct vxlan_fdb *vxlan_find_mac(struct vxlan_dev *vxlan,
+static struct vxlan_fdb *__vxlan_find_mac(struct vxlan_dev *vxlan,
const u8 *mac)
{
return NULL;
}
+static struct vxlan_fdb *vxlan_find_mac(struct vxlan_dev *vxlan,
+ const u8 *mac)
+{
+ struct vxlan_fdb *f;
+
+ f = __vxlan_find_mac(vxlan, mac);
+ if (f)
+ f->used = jiffies;
+
+ return f;
+}
+
/* Add/update destinations for multicast */
static int vxlan_fdb_append(struct vxlan_fdb *f,
__be32 ip, __be16 port, __u32 vni, __u32 ifindex)
struct vxlan_fdb *f;
int notify = 0;
- f = vxlan_find_mac(vxlan, mac);
+ f = __vxlan_find_mac(vxlan, mac);
if (f) {
if (flags & NLM_F_EXCL) {
netdev_dbg(vxlan->dev,
f = vxlan_find_mac(vxlan, src_mac);
if (likely(f)) {
- f->used = jiffies;
if (likely(f->remote.remote_ip == src_ip))
return;
{
int i;
- if (!AR_SREV_9462(ah) && !AR_SREV_9565(ah))
+ if (!AR_SREV_9462(ah) && !AR_SREV_9565(ah) && !AR_SREV_9485(ah))
return;
for (i = 0; i < AR9300_MAX_CHAINS; i++) {
{0x0000a284, 0x00000000, 0x00000000, 0x000002a0, 0x000002a0},
{0x0000a288, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
{0x0000a28c, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
- {0x0000a2c4, 0x00158d18, 0x00158d18, 0x00158d18, 0x00158d18},
+ {0x0000a2c4, 0x00158d18, 0x00158d18, 0x00058d18, 0x00058d18},
{0x0000a2d0, 0x00071981, 0x00071981, 0x00071982, 0x00071982},
{0x0000a2d8, 0xf999a83a, 0xf999a83a, 0xf999a83a, 0xf999a83a},
{0x0000a358, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
int sched;
int paused;
u8 state;
+ bool stop_cb;
};
struct ath_node {
void ath_tx_edma_tasklet(struct ath_softc *sc);
int ath_tx_aggr_start(struct ath_softc *sc, struct ieee80211_sta *sta,
u16 tid, u16 *ssn);
-void ath_tx_aggr_stop(struct ath_softc *sc, struct ieee80211_sta *sta, u16 tid);
+bool ath_tx_aggr_stop(struct ath_softc *sc, struct ieee80211_sta *sta, u16 tid,
+ bool flush);
void ath_tx_aggr_resume(struct ath_softc *sc, struct ieee80211_sta *sta, u16 tid);
void ath_tx_aggr_wakeup(struct ath_softc *sc, struct ath_node *an);
WARN_ON(i != ATH9K_SSTATS_LEN);
}
+void ath9k_deinit_debug(struct ath_softc *sc)
+{
+ if (config_enabled(CONFIG_ATH9K_DEBUGFS) && sc->rfs_chan_spec_scan) {
+ relay_close(sc->rfs_chan_spec_scan);
+ sc->rfs_chan_spec_scan = NULL;
+ }
+}
+
int ath9k_init_debug(struct ath_hw *ah)
{
struct ath_common *common = ath9k_hw_common(ah);
};
int ath9k_init_debug(struct ath_hw *ah);
+void ath9k_deinit_debug(struct ath_softc *sc);
void ath_debug_stat_interrupt(struct ath_softc *sc, enum ath9k_int status);
void ath_debug_stat_tx(struct ath_softc *sc, struct ath_buf *bf,
return 0;
}
+static inline void ath9k_deinit_debug(struct ath_softc *sc)
+{
+}
+
static inline void ath_debug_stat_interrupt(struct ath_softc *sc,
enum ath9k_int status)
{
if (!ath_is_world_regd(reg)) {
error = regulatory_hint(hw->wiphy, reg->alpha2);
if (error)
- goto unregister;
+ goto debug_cleanup;
}
ath_init_leds(sc);
return 0;
+debug_cleanup:
+ ath9k_deinit_debug(sc);
unregister:
ieee80211_unregister_hw(hw);
rx_cleanup:
sc->dfs_detector->exit(sc->dfs_detector);
ath9k_eeprom_release(sc);
-
- if (config_enabled(CONFIG_ATH9K_DEBUGFS) && sc->rfs_chan_spec_scan) {
- relay_close(sc->rfs_chan_spec_scan);
- sc->rfs_chan_spec_scan = NULL;
- }
}
void ath9k_deinit_device(struct ath_softc *sc)
ath9k_ps_restore(sc);
+ ath9k_deinit_debug(sc);
ieee80211_unregister_hw(hw);
ath_rx_cleanup(sc);
ath9k_deinit_softc(sc);
u16 tid, u16 *ssn, u8 buf_size)
{
struct ath_softc *sc = hw->priv;
+ bool flush = false;
int ret = 0;
local_bh_disable();
ieee80211_start_tx_ba_cb_irqsafe(vif, sta->addr, tid);
ath9k_ps_restore(sc);
break;
- case IEEE80211_AMPDU_TX_STOP_CONT:
case IEEE80211_AMPDU_TX_STOP_FLUSH:
case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT:
+ flush = true;
+ case IEEE80211_AMPDU_TX_STOP_CONT:
ath9k_ps_wakeup(sc);
- ath_tx_aggr_stop(sc, sta, tid);
- ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
+ if (ath_tx_aggr_stop(sc, sta, tid, flush))
+ ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid);
ath9k_ps_restore(sc);
break;
case IEEE80211_AMPDU_TX_OPERATIONAL:
ARRAY_SIZE(bf->rates));
}
-static void ath_tx_flush_tid(struct ath_softc *sc, struct ath_atx_tid *tid)
+static void ath_tx_clear_tid(struct ath_softc *sc, struct ath_atx_tid *tid)
+{
+ tid->state &= ~AGGR_ADDBA_COMPLETE;
+ tid->state &= ~AGGR_CLEANUP;
+ if (!tid->stop_cb)
+ return;
+
+ ieee80211_start_tx_ba_cb_irqsafe(tid->an->vif, tid->an->sta->addr,
+ tid->tidno);
+ tid->stop_cb = false;
+}
+
+static void ath_tx_flush_tid(struct ath_softc *sc, struct ath_atx_tid *tid,
+ bool flush_packets)
{
struct ath_txq *txq = tid->ac->txq;
struct sk_buff *skb;
while ((skb = __skb_dequeue(&tid->buf_q))) {
fi = get_frame_info(skb);
bf = fi->bf;
+ if (!bf && !flush_packets)
+ bf = ath_tx_setup_buffer(sc, txq, tid, skb);
if (!bf) {
- bf = ath_tx_setup_buffer(sc, txq, tid, skb);
- if (!bf) {
- ieee80211_free_txskb(sc->hw, skb);
- continue;
- }
+ ieee80211_free_txskb(sc->hw, skb);
+ continue;
}
- if (fi->retries) {
+ if (fi->retries || flush_packets) {
list_add_tail(&bf->list, &bf_head);
ath_tx_update_baw(sc, tid, bf->bf_state.seqno);
ath_tx_complete_buf(sc, bf, txq, &bf_head, &ts, 0);
}
}
- if (tid->baw_head == tid->baw_tail) {
- tid->state &= ~AGGR_ADDBA_COMPLETE;
- tid->state &= ~AGGR_CLEANUP;
- }
+ if (tid->baw_head == tid->baw_tail)
+ ath_tx_clear_tid(sc, tid);
- if (sendbar) {
+ if (sendbar && !flush_packets) {
ath_txq_unlock(sc, txq);
ath_send_bar(tid, tid->seq_start);
ath_txq_lock(sc, txq);
list_add_tail(&bf->list, &bf_head);
- if (fi->retries)
- ath_tx_update_baw(sc, tid, bf->bf_state.seqno);
-
+ ath_tx_update_baw(sc, tid, bf->bf_state.seqno);
ath_tx_complete_buf(sc, bf, txq, &bf_head, &ts, 0);
}
}
if (tid->state & AGGR_CLEANUP)
- ath_tx_flush_tid(sc, tid);
+ ath_tx_flush_tid(sc, tid, false);
rcu_read_unlock();
struct ath_tx_status *ts, struct ath_buf *bf,
struct list_head *bf_head)
{
+ struct ieee80211_tx_info *info;
bool txok, flush;
txok = !(ts->ts_status & ATH9K_TXERR_MASK);
txq->axq_ampdu_depth--;
if (!bf_isampdu(bf)) {
- if (!flush)
+ if (!flush) {
+ info = IEEE80211_SKB_CB(bf->bf_mpdu);
+ memcpy(info->control.rates, bf->rates,
+ sizeof(info->control.rates));
ath_tx_rc_status(sc, bf, ts, 1, txok ? 0 : 1, txok);
+ }
ath_tx_complete_buf(sc, bf, txq, bf_head, ts, txok);
} else
ath_tx_complete_aggr(sc, txq, bf, bf_head, ts, txok);
skb = bf->bf_mpdu;
tx_info = IEEE80211_SKB_CB(skb);
- rates = tx_info->control.rates;
+ rates = bf->rates;
/*
* Find the lowest frame length among the rate series that will have a
return 0;
}
-void ath_tx_aggr_stop(struct ath_softc *sc, struct ieee80211_sta *sta, u16 tid)
+bool ath_tx_aggr_stop(struct ath_softc *sc, struct ieee80211_sta *sta, u16 tid,
+ bool flush)
{
struct ath_node *an = (struct ath_node *)sta->drv_priv;
struct ath_atx_tid *txtid = ATH_AN_2_TID(an, tid);
struct ath_txq *txq = txtid->ac->txq;
+ bool ret = !flush;
+
+ if (flush)
+ txtid->stop_cb = false;
if (txtid->state & AGGR_CLEANUP)
- return;
+ return false;
if (!(txtid->state & AGGR_ADDBA_COMPLETE)) {
txtid->state &= ~AGGR_ADDBA_PROGRESS;
- return;
+ return ret;
}
ath_txq_lock(sc, txq);
* TID can only be reused after all in-progress subframes have been
* completed.
*/
- if (txtid->baw_head != txtid->baw_tail)
+ if (txtid->baw_head != txtid->baw_tail) {
txtid->state |= AGGR_CLEANUP;
- else
+ ret = false;
+ txtid->stop_cb = !flush;
+ } else {
txtid->state &= ~AGGR_ADDBA_COMPLETE;
+ }
- ath_tx_flush_tid(sc, txtid);
+ ath_tx_flush_tid(sc, txtid, flush);
ath_txq_unlock_complete(sc, txq);
+ return ret;
}
void ath_tx_aggr_sleep(struct ieee80211_sta *sta, struct ath_softc *sc,
tid->ac = &an->ac[acno];
tid->state &= ~AGGR_ADDBA_COMPLETE;
tid->state &= ~AGGR_ADDBA_PROGRESS;
+ tid->stop_cb = false;
}
for (acno = 0, ac = &an->ac[acno];
}
ath_tid_drain(sc, txq, tid);
- tid->state &= ~AGGR_ADDBA_COMPLETE;
- tid->state &= ~AGGR_CLEANUP;
+ ath_tx_clear_tid(sc, tid);
ath_txq_unlock(sc, txq);
}
.types = BIT(NL80211_IFTYPE_P2P_CLIENT) |
BIT(NL80211_IFTYPE_P2P_GO)
},
+ {
+ .max = 1,
+ .types = BIT(NL80211_IFTYPE_P2P_DEVICE)
+ }
};
static const struct ieee80211_iface_combination brcmf_iface_combos[] = {
{
BIT(NL80211_IFTYPE_ADHOC) |
BIT(NL80211_IFTYPE_AP) |
BIT(NL80211_IFTYPE_P2P_CLIENT) |
- BIT(NL80211_IFTYPE_P2P_GO);
+ BIT(NL80211_IFTYPE_P2P_GO) |
+ BIT(NL80211_IFTYPE_P2P_DEVICE);
wiphy->iface_combinations = brcmf_iface_combos;
wiphy->n_iface_combinations = ARRAY_SIZE(brcmf_iface_combos);
wiphy->bands[IEEE80211_BAND_2GHZ] = &__wl_band_2ghz;
}
EXPORT_SYMBOL(il_setup_rx_scan_handlers);
-inline u16
+u16
il_get_active_dwell_time(struct il_priv *il, enum ieee80211_band band,
u8 n_probes)
{
REPLY_DEBUG_CMD = 0xf0,
DEBUG_LOG_MSG = 0xf7,
+ MCAST_FILTER_CMD = 0xd0,
+
/* D3 commands/notifications */
D3_CONFIG_CMD = 0xd3,
PROT_OFFLOAD_CONFIG_CMD = 0xd4,
u8 data[0];
} __packed; /* PHY_CALIB_OVERRIDE_VALUES_S */
+#define MAX_PORT_ID_NUM 2
+
+/**
+ * struct iwl_mcast_filter_cmd - configure multicast filter.
+ * @filter_own: Set 1 to filter out multicast packets sent by station itself
+ * @port_id: Multicast MAC addresses array specifier. This is a strange way
+ * to identify network interface adopted in host-device IF.
+ * It is used by FW as index in array of addresses. This array has
+ * MAX_PORT_ID_NUM members.
+ * @count: Number of MAC addresses in the array
+ * @pass_all: Set 1 to pass all multicast packets.
+ * @bssid: current association BSSID.
+ * @addr_list: Place holder for array of MAC addresses.
+ * IMPORTANT: add padding if necessary to ensure DWORD alignment.
+ */
+struct iwl_mcast_filter_cmd {
+ u8 filter_own;
+ u8 port_id;
+ u8 count;
+ u8 pass_all;
+ u8 bssid[6];
+ u8 reserved[2];
+ u8 addr_list[0];
+} __packed; /* MCAST_FILTERING_CMD_API_S_VER_1 */
+
#endif /* __fw_api_h__ */
*/
static void iwl_mvm_mac_ctxt_cmd_fill_sta(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
- struct iwl_mac_data_sta *ctxt_sta)
+ struct iwl_mac_data_sta *ctxt_sta,
+ bool force_assoc_off)
{
/* We need the dtim_period to set the MAC as associated */
- if (vif->bss_conf.assoc && vif->bss_conf.dtim_period) {
+ if (vif->bss_conf.assoc && vif->bss_conf.dtim_period &&
+ !force_assoc_off) {
u32 dtim_offs;
/*
cmd.filter_flags &= ~cpu_to_le32(MAC_FILTER_IN_BEACON);
/* Fill the data specific for station mode */
- iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.sta);
+ iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.sta,
+ action == FW_CTXT_ACTION_ADD);
return iwl_mvm_mac_ctxt_send_cmd(mvm, &cmd);
}
iwl_mvm_mac_ctxt_cmd_common(mvm, vif, &cmd, action);
/* Fill the data specific for station mode */
- iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.p2p_sta.sta);
+ iwl_mvm_mac_ctxt_cmd_fill_sta(mvm, vif, &cmd.p2p_sta.sta,
+ action == FW_CTXT_ACTION_ADD);
cmd.p2p_sta.ctwin = cpu_to_le32(noa->oppps_ctwindow &
IEEE80211_P2P_OPPPS_CTWINDOW_MASK);
*total_flags = 0;
}
+static int iwl_mvm_configure_mcast_filter(struct iwl_mvm *mvm,
+ struct ieee80211_vif *vif)
+{
+ struct iwl_mcast_filter_cmd mcast_filter_cmd = {
+ .pass_all = 1,
+ };
+
+ memcpy(mcast_filter_cmd.bssid, vif->bss_conf.bssid, ETH_ALEN);
+
+ return iwl_mvm_send_cmd_pdu(mvm, MCAST_FILTER_CMD, CMD_SYNC,
+ sizeof(mcast_filter_cmd),
+ &mcast_filter_cmd);
+}
+
static void iwl_mvm_bss_info_changed_station(struct iwl_mvm *mvm,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
return;
}
iwl_mvm_bt_coex_vif_assoc(mvm, vif);
+ iwl_mvm_configure_mcast_filter(mvm, vif);
} else if (mvmvif->ap_sta_id != IWL_MVM_STATION_COUNT) {
/* remove AP station now that the MAC is unassoc */
ret = iwl_mvm_rm_sta_id(mvm, vif, mvmvif->ap_sta_id);
switch (cmd) {
case STA_NOTIFY_SLEEP:
- if (atomic_read(&mvmsta->pending_frames) > 0)
+ if (atomic_read(&mvm->pending_frames[mvmsta->sta_id]) > 0)
ieee80211_sta_block_awake(hw, sta, true);
/*
* The fw updates the STA to be asleep. Tx packets on the Tx
struct ieee80211_sta __rcu *fw_id_to_mac_id[IWL_MVM_STATION_COUNT];
struct work_struct sta_drained_wk;
unsigned long sta_drained[BITS_TO_LONGS(IWL_MVM_STATION_COUNT)];
+ atomic_t pending_frames[IWL_MVM_STATION_COUNT];
/* configured by mac80211 */
u32 rts_threshold;
CMD(BT_COEX_PROT_ENV),
CMD(BT_PROFILE_NOTIFICATION),
CMD(BT_CONFIG),
+ CMD(MCAST_FILTER_CMD),
};
#undef CMD
else
cmd->type = cpu_to_le32(SCAN_TYPE_FORCED);
+ /*
+ * TODO: This is a WA due to a bug in the FW AUX framework that does not
+ * properly handle time events that fail to be scheduled
+ */
+ cmd->type = cpu_to_le32(SCAN_TYPE_FORCED);
+
cmd->repeats = cpu_to_le32(1);
/*
mvm_sta->max_agg_bufsize = LINK_QUAL_AGG_FRAME_LIMIT_DEF;
/* HW restart, don't assume the memory has been zeroed */
- atomic_set(&mvm_sta->pending_frames, 0);
+ atomic_set(&mvm->pending_frames[sta_id], 0);
mvm_sta->tid_disable_agg = 0;
mvm_sta->tfd_queue_msk = 0;
for (i = 0; i < IEEE80211_NUM_ACS; i++)
mvmvif->ap_sta_id = IWL_MVM_STATION_COUNT;
}
+ /*
+ * Make sure that the tx response code sees the station as -EBUSY and
+ * calls the drain worker.
+ */
+ spin_lock_bh(&mvm_sta->lock);
/*
* There are frames pending on the AC queues for this station.
* We need to wait until all the frames are drained...
*/
- if (atomic_read(&mvm_sta->pending_frames)) {
- ret = iwl_mvm_drain_sta(mvm, mvm_sta, true);
+ if (atomic_read(&mvm->pending_frames[mvm_sta->sta_id])) {
rcu_assign_pointer(mvm->fw_id_to_mac_id[mvm_sta->sta_id],
ERR_PTR(-EBUSY));
+ spin_unlock_bh(&mvm_sta->lock);
+ ret = iwl_mvm_drain_sta(mvm, mvm_sta, true);
} else {
+ spin_unlock_bh(&mvm_sta->lock);
ret = iwl_mvm_rm_sta_common(mvm, mvm_sta->sta_id);
rcu_assign_pointer(mvm->fw_id_to_mac_id[mvm_sta->sta_id], NULL);
}
* @bt_reduced_txpower: is reduced tx power enabled for this station
* @lock: lock to protect the whole struct. Since %tid_data is access from Tx
* and from Tx response flow, it needs a spinlock.
- * @pending_frames: number of frames for this STA on the shared Tx queues.
* @tid_data: per tid data. Look at %iwl_mvm_tid_data.
*
* When mac80211 creates a station it reserves some space (hw->sta_data_size)
u8 max_agg_bufsize;
bool bt_reduced_txpower;
spinlock_t lock;
- atomic_t pending_frames;
struct iwl_mvm_tid_data tid_data[IWL_MAX_TID_COUNT];
struct iwl_lq_sta lq_sta;
struct ieee80211_vif *vif;
spin_unlock(&mvmsta->lock);
- if (mvmsta->vif->type == NL80211_IFTYPE_AP &&
- txq_id < IWL_MVM_FIRST_AGG_QUEUE)
- atomic_inc(&mvmsta->pending_frames);
+ if (txq_id < IWL_MVM_FIRST_AGG_QUEUE)
+ atomic_inc(&mvm->pending_frames[mvmsta->sta_id]);
return 0;
/*
* If the txq is not an AMPDU queue, there is no chance we freed
* several skbs. Check that out...
- * If there are no pending frames for this STA, notify mac80211 that
- * this station can go to sleep in its STA table.
*/
- if (txq_id < IWL_MVM_FIRST_AGG_QUEUE && mvmsta &&
- !WARN_ON(skb_freed > 1) &&
- mvmsta->vif->type == NL80211_IFTYPE_AP &&
- atomic_sub_and_test(skb_freed, &mvmsta->pending_frames)) {
- ieee80211_sta_block_awake(mvm->hw, sta, false);
- set_bit(sta_id, mvm->sta_drained);
- schedule_work(&mvm->sta_drained_wk);
+ if (txq_id < IWL_MVM_FIRST_AGG_QUEUE && !WARN_ON(skb_freed > 1) &&
+ atomic_sub_and_test(skb_freed, &mvm->pending_frames[sta_id])) {
+ if (mvmsta) {
+ /*
+ * If there are no pending frames for this STA, notify
+ * mac80211 that this station can go to sleep in its
+ * STA table.
+ */
+ if (mvmsta->vif->type == NL80211_IFTYPE_AP)
+ ieee80211_sta_block_awake(mvm->hw, sta, false);
+ /*
+ * We might very well have taken mvmsta pointer while
+ * the station was being removed. The remove flow might
+ * have seen a pending_frame (because we didn't take
+ * the lock) even if now the queues are drained. So make
+ * really sure now that this the station is not being
+ * removed. If it is, run the drain worker to remove it.
+ */
+ spin_lock_bh(&mvmsta->lock);
+ sta = rcu_dereference(mvm->fw_id_to_mac_id[sta_id]);
+ if (IS_ERR_OR_NULL(sta)) {
+ /*
+ * Station disappeared in the meantime:
+ * so we are draining.
+ */
+ set_bit(sta_id, mvm->sta_drained);
+ schedule_work(&mvm->sta_drained_wk);
+ }
+ spin_unlock_bh(&mvmsta->lock);
+ } else if (!mvmsta) {
+ /* Tx response without STA, so we are draining */
+ set_bit(sta_id, mvm->sta_drained);
+ schedule_work(&mvm->sta_drained_wk);
+ }
}
rcu_read_unlock();
class_destroy(hwsim_class);
}
-
-static struct device_driver mac80211_hwsim_driver = {
- .name = "mac80211_hwsim",
- .bus = &platform_bus_type,
- .owner = THIS_MODULE,
+static struct platform_driver mac80211_hwsim_driver = {
+ .driver = {
+ .name = "mac80211_hwsim",
+ .owner = THIS_MODULE,
+ },
};
static const struct net_device_ops hwsim_netdev_ops = {
spin_lock_init(&hwsim_radio_lock);
INIT_LIST_HEAD(&hwsim_radios);
- err = driver_register(&mac80211_hwsim_driver);
+ err = platform_driver_register(&mac80211_hwsim_driver);
if (err)
return err;
err = -ENOMEM;
goto failed_drvdata;
}
- data->dev->driver = &mac80211_hwsim_driver;
+ data->dev->driver = &mac80211_hwsim_driver.driver;
err = device_bind_driver(data->dev);
if (err != 0) {
printk(KERN_DEBUG
failed:
mac80211_hwsim_free();
failed_unregister_driver:
- driver_unregister(&mac80211_hwsim_driver);
+ platform_driver_unregister(&mac80211_hwsim_driver);
return err;
}
module_init(init_mac80211_hwsim);
mac80211_hwsim_free();
unregister_netdev(hwsim_mon);
- driver_unregister(&mac80211_hwsim_driver);
+ platform_driver_unregister(&mac80211_hwsim_driver);
}
module_exit(exit_mac80211_hwsim);
rxmcs == DESC92C_RATE11M)
struct phy_rx_agc_info_t {
- #if __LITTLE_ENDIAN
+ #ifdef __LITTLE_ENDIAN
u8 gain:7, trsw:1;
#else
u8 trsw:1, gain:7;
u8 stream_target_csi[2];
u8 sig_evm;
u8 rsvd_3;
-#if __LITTLE_ENDIAN
+#ifdef __LITTLE_ENDIAN
u8 antsel_rx_keep_2:1; /*ex_intf_flg:1;*/
u8 sgi_en:1;
u8 rxsc:2;
{RTL_USB_DEVICE(0x07aa, 0x0056, rtl92cu_hal_cfg)}, /*ATKK-Gemtek*/
{RTL_USB_DEVICE(0x07b8, 0x8178, rtl92cu_hal_cfg)}, /*Funai -Abocom*/
{RTL_USB_DEVICE(0x0846, 0x9021, rtl92cu_hal_cfg)}, /*Netgear-Sercomm*/
+ {RTL_USB_DEVICE(0x0846, 0xf001, rtl92cu_hal_cfg)}, /*On Netwrks N300MA*/
{RTL_USB_DEVICE(0x0b05, 0x17ab, rtl92cu_hal_cfg)}, /*ASUS-Edimax*/
{RTL_USB_DEVICE(0x0bda, 0x8186, rtl92cu_hal_cfg)}, /*Realtek 92CE-VAU*/
{RTL_USB_DEVICE(0x0df6, 0x0061, rtl92cu_hal_cfg)}, /*Sitecom-Edimax*/
.probe = superio_probe,
};
-static int __init superio_modinit(void)
-{
- return pci_register_driver(&superio_driver);
-}
-
-static void __exit superio_exit(void)
-{
- pci_unregister_driver(&superio_driver);
-}
-
-module_init(superio_modinit);
-module_exit(superio_exit);
+module_pci_driver(superio_driver);
return AE_OK ;
}
+void acpiphp_check_host_bridge(acpi_handle handle)
+{
+ struct acpiphp_bridge *bridge;
+
+ bridge = acpiphp_handle_to_bridge(handle);
+ if (bridge) {
+ acpiphp_check_bridge(bridge);
+ put_bridge(bridge);
+ }
+
+ acpi_walk_namespace(ACPI_TYPE_DEVICE, handle,
+ ACPI_UINT32_MAX, check_sub_bridges, NULL, NULL, NULL);
+}
+
static void _handle_hotplug_event_bridge(struct work_struct *work)
{
struct acpiphp_bridge *bridge;
config BATTERY_BQ27x00
tristate "BQ27x00 battery driver"
+ depends on I2C || I2C=n
help
Say Y here to enable support for batteries with BQ27x00 (I2C/HDQ) chips.
tristate "TI LP8788 charger driver"
depends on MFD_LP8788
depends on LP8788_ADC
+ depends on IIO
help
Say Y to enable support for the LP8788 linear charger.
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
-MODULE_ALIAS("platform:pm2xxx-charger");
+MODULE_ALIAS("i2c:pm2xxx-charger");
MODULE_DESCRIPTION("PM2xxx charger management driver");
struct wm831x_backup *devdata = platform_get_drvdata(pdev);
power_supply_unregister(&devdata->backup);
- kfree(devdata->backup.name);
return 0;
}
If you are unsure about this, say N here.
+choice
+ prompt "Enumeration method"
+ depends on RAPIDIO
+ default RAPIDIO_ENUM_BASIC
+ help
+ There are different enumeration and discovery mechanisms offered
+ for RapidIO subsystem. You may select single built-in method or
+ or any number of methods to be built as modules.
+ Selecting a built-in method disables use of loadable methods.
+
+ If unsure, select Basic built-in.
+
+config RAPIDIO_ENUM_BASIC
+ tristate "Basic"
+ help
+ This option includes basic RapidIO fabric enumeration and discovery
+ mechanism similar to one described in RapidIO specification Annex 1.
+
+endchoice
+
source "drivers/rapidio/switches/Kconfig"
#
# Makefile for RapidIO interconnect services
#
-obj-y += rio.o rio-access.o rio-driver.o rio-scan.o rio-sysfs.o
+obj-y += rio.o rio-access.o rio-driver.o rio-sysfs.o
+obj-$(CONFIG_RAPIDIO_ENUM_BASIC) += rio-scan.o
obj-$(CONFIG_RAPIDIO) += switches/
obj-$(CONFIG_RAPIDIO) += devices/
u32 intval;
u32 ch_inte;
+ /* For MSI mode disable all device-level interrupts */
+ if (priv->flags & TSI721_USING_MSI)
+ iowrite32(0, priv->regs + TSI721_DEV_INTE);
+
dev_int = ioread32(priv->regs + TSI721_DEV_INT);
if (!dev_int)
return IRQ_NONE;
}
}
#endif
+
+ /* For MSI mode re-enable device-level interrupts */
+ if (priv->flags & TSI721_USING_MSI) {
+ dev_int = TSI721_DEV_INT_SR2PC_CH | TSI721_DEV_INT_SRIO |
+ TSI721_DEV_INT_SMSG_CH | TSI721_DEV_INT_BDMA_CH;
+ iowrite32(dev_int, priv->regs + TSI721_DEV_INTE);
+ }
+
return IRQ_HANDLED;
}
driver_unregister(&rdrv->driver);
}
+void rio_attach_device(struct rio_dev *rdev)
+{
+ rdev->dev.bus = &rio_bus_type;
+ rdev->dev.parent = &rio_bus;
+}
+EXPORT_SYMBOL_GPL(rio_attach_device);
+
/**
* rio_match_bus - Tell if a RIO device structure has a matching RIO driver device id structure
* @dev: the standard device structure to match against
.name = "rapidio",
.match = rio_match_bus,
.dev_attrs = rio_dev_attrs,
+ .bus_attrs = rio_bus_attrs,
.probe = rio_device_probe,
.remove = rio_device_remove,
};
#include "rio.h"
-LIST_HEAD(rio_devices);
-
static void rio_init_em(struct rio_dev *rdev);
-DEFINE_SPINLOCK(rio_global_list_lock);
-
static int next_destid = 0;
static int next_comptag = 1;
return 0;
}
-/**
- * rio_switch_init - Sets switch operations for a particular vendor switch
- * @rdev: RIO device
- * @do_enum: Enumeration/Discovery mode flag
- *
- * Searches the RIO switch ops table for known switch types. If the vid
- * and did match a switch table entry, then call switch initialization
- * routine to setup switch-specific routines.
- */
-static void rio_switch_init(struct rio_dev *rdev, int do_enum)
-{
- struct rio_switch_ops *cur = __start_rio_switch_ops;
- struct rio_switch_ops *end = __end_rio_switch_ops;
-
- while (cur < end) {
- if ((cur->vid == rdev->vid) && (cur->did == rdev->did)) {
- pr_debug("RIO: calling init routine for %s\n",
- rio_name(rdev));
- cur->init_hook(rdev, do_enum);
- break;
- }
- cur++;
- }
-
- if ((cur >= end) && (rdev->pef & RIO_PEF_STD_RT)) {
- pr_debug("RIO: adding STD routing ops for %s\n",
- rio_name(rdev));
- rdev->rswitch->add_entry = rio_std_route_add_entry;
- rdev->rswitch->get_entry = rio_std_route_get_entry;
- rdev->rswitch->clr_table = rio_std_route_clr_table;
- }
-
- if (!rdev->rswitch->add_entry || !rdev->rswitch->get_entry)
- printk(KERN_ERR "RIO: missing routing ops for %s\n",
- rio_name(rdev));
-}
-
-/**
- * rio_add_device- Adds a RIO device to the device model
- * @rdev: RIO device
- *
- * Adds the RIO device to the global device list and adds the RIO
- * device to the RIO device list. Creates the generic sysfs nodes
- * for an RIO device.
- */
-static int rio_add_device(struct rio_dev *rdev)
-{
- int err;
-
- err = device_add(&rdev->dev);
- if (err)
- return err;
-
- spin_lock(&rio_global_list_lock);
- list_add_tail(&rdev->global_list, &rio_devices);
- spin_unlock(&rio_global_list_lock);
-
- rio_create_sysfs_dev_files(rdev);
-
- return 0;
-}
-
-/**
- * rio_enable_rx_tx_port - enable input receiver and output transmitter of
- * given port
- * @port: Master port associated with the RIO network
- * @local: local=1 select local port otherwise a far device is reached
- * @destid: Destination ID of the device to check host bit
- * @hopcount: Number of hops to reach the target
- * @port_num: Port (-number on switch) to enable on a far end device
- *
- * Returns 0 or 1 from on General Control Command and Status Register
- * (EXT_PTR+0x3C)
- */
-inline int rio_enable_rx_tx_port(struct rio_mport *port,
- int local, u16 destid,
- u8 hopcount, u8 port_num) {
-#ifdef CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS
- u32 regval;
- u32 ext_ftr_ptr;
-
- /*
- * enable rx input tx output port
- */
- pr_debug("rio_enable_rx_tx_port(local = %d, destid = %d, hopcount = "
- "%d, port_num = %d)\n", local, destid, hopcount, port_num);
-
- ext_ftr_ptr = rio_mport_get_physefb(port, local, destid, hopcount);
-
- if (local) {
- rio_local_read_config_32(port, ext_ftr_ptr +
- RIO_PORT_N_CTL_CSR(0),
- ®val);
- } else {
- if (rio_mport_read_config_32(port, destid, hopcount,
- ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), ®val) < 0)
- return -EIO;
- }
-
- if (regval & RIO_PORT_N_CTL_P_TYP_SER) {
- /* serial */
- regval = regval | RIO_PORT_N_CTL_EN_RX_SER
- | RIO_PORT_N_CTL_EN_TX_SER;
- } else {
- /* parallel */
- regval = regval | RIO_PORT_N_CTL_EN_RX_PAR
- | RIO_PORT_N_CTL_EN_TX_PAR;
- }
-
- if (local) {
- rio_local_write_config_32(port, ext_ftr_ptr +
- RIO_PORT_N_CTL_CSR(0), regval);
- } else {
- if (rio_mport_write_config_32(port, destid, hopcount,
- ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), regval) < 0)
- return -EIO;
- }
-#endif
- return 0;
-}
-
/**
* rio_setup_device- Allocates and sets up a RIO device
* @net: RIO network
rdev->destid);
}
- rdev->dev.bus = &rio_bus_type;
- rdev->dev.parent = &rio_bus;
+ rio_attach_device(rdev);
device_initialize(&rdev->dev);
rdev->dev.release = rio_release_dev;
/**
* rio_enum_mport- Start enumeration through a master port
* @mport: Master port to send transactions
+ * @flags: Enumeration control flags
*
* Starts the enumeration process. If somebody has enumerated our
* master port device, then give up. If not and we have an active
* link, then start recursive peer enumeration. Returns %0 if
* enumeration succeeds or %-EBUSY if enumeration fails.
*/
-int rio_enum_mport(struct rio_mport *mport)
+int rio_enum_mport(struct rio_mport *mport, u32 flags)
{
struct rio_net *net = NULL;
int rc = 0;
printk(KERN_INFO "RIO: enumerate master port %d, %s\n", mport->id,
mport->name);
+
+ /*
+ * To avoid multiple start requests (repeat enumeration is not supported
+ * by this method) check if enumeration/discovery was performed for this
+ * mport: if mport was added into the list of mports for a net exit
+ * with error.
+ */
+ if (mport->nnode.next || mport->nnode.prev)
+ return -EBUSY;
+
/* If somebody else enumerated our master port device, bail. */
if (rio_enum_host(mport) < 0) {
printk(KERN_INFO
/**
* rio_disc_mport- Start discovery through a master port
* @mport: Master port to send transactions
+ * @flags: discovery control flags
*
* Starts the discovery process. If we have an active link,
- * then wait for the signal that enumeration is complete.
+ * then wait for the signal that enumeration is complete (if wait
+ * is allowed).
* When enumeration completion is signaled, start recursive
* peer discovery. Returns %0 if discovery succeeds or %-EBUSY
* on failure.
*/
-int rio_disc_mport(struct rio_mport *mport)
+int rio_disc_mport(struct rio_mport *mport, u32 flags)
{
struct rio_net *net = NULL;
unsigned long to_end;
/* If master port has an active link, allocate net and discover peers */
if (rio_mport_is_active(mport)) {
+ if (rio_enum_complete(mport))
+ goto enum_done;
+ else if (flags & RIO_SCAN_ENUM_NO_WAIT)
+ return -EAGAIN;
+
pr_debug("RIO: wait for enumeration to complete...\n");
to_end = jiffies + CONFIG_RAPIDIO_DISC_TIMEOUT * HZ;
bail:
return -EBUSY;
}
+
+static struct rio_scan rio_scan_ops = {
+ .enumerate = rio_enum_mport,
+ .discover = rio_disc_mport,
+};
+
+static bool scan;
+module_param(scan, bool, 0);
+MODULE_PARM_DESC(scan, "Start RapidIO network enumeration/discovery "
+ "(default = 0)");
+
+/**
+ * rio_basic_attach:
+ *
+ * When this enumeration/discovery method is loaded as a module this function
+ * registers its specific enumeration and discover routines for all available
+ * RapidIO mport devices. The "scan" command line parameter controls ability of
+ * the module to start RapidIO enumeration/discovery automatically.
+ *
+ * Returns 0 for success or -EIO if unable to register itself.
+ *
+ * This enumeration/discovery method cannot be unloaded and therefore does not
+ * provide a matching cleanup_module routine.
+ */
+
+static int __init rio_basic_attach(void)
+{
+ if (rio_register_scan(RIO_MPORT_ANY, &rio_scan_ops))
+ return -EIO;
+ if (scan)
+ rio_init_mports();
+ return 0;
+}
+
+late_initcall(rio_basic_attach);
+
+MODULE_DESCRIPTION("Basic RapidIO enumeration/discovery");
+MODULE_LICENSE("GPL");
rdev->rswitch->sw_sysfs(rdev, RIO_SW_SYSFS_REMOVE);
}
}
+
+static ssize_t bus_scan_store(struct bus_type *bus, const char *buf,
+ size_t count)
+{
+ long val;
+ struct rio_mport *port = NULL;
+ int rc;
+
+ if (kstrtol(buf, 0, &val) < 0)
+ return -EINVAL;
+
+ if (val == RIO_MPORT_ANY) {
+ rc = rio_init_mports();
+ goto exit;
+ }
+
+ if (val < 0 || val >= RIO_MAX_MPORTS)
+ return -EINVAL;
+
+ port = rio_find_mport((int)val);
+
+ if (!port) {
+ pr_debug("RIO: %s: mport_%d not available\n",
+ __func__, (int)val);
+ return -EINVAL;
+ }
+
+ if (!port->nscan)
+ return -EINVAL;
+
+ if (port->host_deviceid >= 0)
+ rc = port->nscan->enumerate(port, 0);
+ else
+ rc = port->nscan->discover(port, RIO_SCAN_ENUM_NO_WAIT);
+exit:
+ if (!rc)
+ rc = count;
+
+ return rc;
+}
+
+struct bus_attribute rio_bus_attrs[] = {
+ __ATTR(scan, (S_IWUSR|S_IWGRP), NULL, bus_scan_store),
+ __ATTR_NULL
+};
#include "rio.h"
+static LIST_HEAD(rio_devices);
+static DEFINE_SPINLOCK(rio_global_list_lock);
+
static LIST_HEAD(rio_mports);
+static DEFINE_MUTEX(rio_mport_list_lock);
static unsigned char next_portid;
static DEFINE_SPINLOCK(rio_mmap_lock);
return (RIO_GET_DID(port->sys_size, result));
}
+/**
+ * rio_add_device- Adds a RIO device to the device model
+ * @rdev: RIO device
+ *
+ * Adds the RIO device to the global device list and adds the RIO
+ * device to the RIO device list. Creates the generic sysfs nodes
+ * for an RIO device.
+ */
+int rio_add_device(struct rio_dev *rdev)
+{
+ int err;
+
+ err = device_add(&rdev->dev);
+ if (err)
+ return err;
+
+ spin_lock(&rio_global_list_lock);
+ list_add_tail(&rdev->global_list, &rio_devices);
+ spin_unlock(&rio_global_list_lock);
+
+ rio_create_sysfs_dev_files(rdev);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rio_add_device);
+
/**
* rio_request_inb_mbox - request inbound mailbox service
* @mport: RIO master port from which to allocate the mailbox resource
return ext_ftr_ptr;
}
+EXPORT_SYMBOL_GPL(rio_mport_get_physefb);
/**
* rio_get_comptag - Begin or continue searching for a RIO device by component tag
spin_unlock(&rio_global_list_lock);
return rdev;
}
+EXPORT_SYMBOL_GPL(rio_get_comptag);
/**
* rio_set_port_lockout - Sets/clears LOCKOUT bit (RIO EM 1.3) for a switch port.
regval);
return 0;
}
+EXPORT_SYMBOL_GPL(rio_set_port_lockout);
+
+/**
+ * rio_switch_init - Sets switch operations for a particular vendor switch
+ * @rdev: RIO device
+ * @do_enum: Enumeration/Discovery mode flag
+ *
+ * Searches the RIO switch ops table for known switch types. If the vid
+ * and did match a switch table entry, then call switch initialization
+ * routine to setup switch-specific routines.
+ */
+void rio_switch_init(struct rio_dev *rdev, int do_enum)
+{
+ struct rio_switch_ops *cur = __start_rio_switch_ops;
+ struct rio_switch_ops *end = __end_rio_switch_ops;
+
+ while (cur < end) {
+ if ((cur->vid == rdev->vid) && (cur->did == rdev->did)) {
+ pr_debug("RIO: calling init routine for %s\n",
+ rio_name(rdev));
+ cur->init_hook(rdev, do_enum);
+ break;
+ }
+ cur++;
+ }
+
+ if ((cur >= end) && (rdev->pef & RIO_PEF_STD_RT)) {
+ pr_debug("RIO: adding STD routing ops for %s\n",
+ rio_name(rdev));
+ rdev->rswitch->add_entry = rio_std_route_add_entry;
+ rdev->rswitch->get_entry = rio_std_route_get_entry;
+ rdev->rswitch->clr_table = rio_std_route_clr_table;
+ }
+
+ if (!rdev->rswitch->add_entry || !rdev->rswitch->get_entry)
+ printk(KERN_ERR "RIO: missing routing ops for %s\n",
+ rio_name(rdev));
+}
+EXPORT_SYMBOL_GPL(rio_switch_init);
+
+/**
+ * rio_enable_rx_tx_port - enable input receiver and output transmitter of
+ * given port
+ * @port: Master port associated with the RIO network
+ * @local: local=1 select local port otherwise a far device is reached
+ * @destid: Destination ID of the device to check host bit
+ * @hopcount: Number of hops to reach the target
+ * @port_num: Port (-number on switch) to enable on a far end device
+ *
+ * Returns 0 or 1 from on General Control Command and Status Register
+ * (EXT_PTR+0x3C)
+ */
+int rio_enable_rx_tx_port(struct rio_mport *port,
+ int local, u16 destid,
+ u8 hopcount, u8 port_num)
+{
+#ifdef CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS
+ u32 regval;
+ u32 ext_ftr_ptr;
+
+ /*
+ * enable rx input tx output port
+ */
+ pr_debug("rio_enable_rx_tx_port(local = %d, destid = %d, hopcount = "
+ "%d, port_num = %d)\n", local, destid, hopcount, port_num);
+
+ ext_ftr_ptr = rio_mport_get_physefb(port, local, destid, hopcount);
+
+ if (local) {
+ rio_local_read_config_32(port, ext_ftr_ptr +
+ RIO_PORT_N_CTL_CSR(0),
+ ®val);
+ } else {
+ if (rio_mport_read_config_32(port, destid, hopcount,
+ ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), ®val) < 0)
+ return -EIO;
+ }
+
+ if (regval & RIO_PORT_N_CTL_P_TYP_SER) {
+ /* serial */
+ regval = regval | RIO_PORT_N_CTL_EN_RX_SER
+ | RIO_PORT_N_CTL_EN_TX_SER;
+ } else {
+ /* parallel */
+ regval = regval | RIO_PORT_N_CTL_EN_RX_PAR
+ | RIO_PORT_N_CTL_EN_TX_PAR;
+ }
+
+ if (local) {
+ rio_local_write_config_32(port, ext_ftr_ptr +
+ RIO_PORT_N_CTL_CSR(0), regval);
+ } else {
+ if (rio_mport_write_config_32(port, destid, hopcount,
+ ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), regval) < 0)
+ return -EIO;
+ }
+#endif
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rio_enable_rx_tx_port);
+
/**
* rio_chk_dev_route - Validate route to the specified device.
return 0;
}
+EXPORT_SYMBOL_GPL(rio_mport_chk_dev_access);
/**
* rio_chk_dev_access - Validate access to the specified device.
return RIO_GET_BLOCK_ID(reg_val);
}
}
+EXPORT_SYMBOL_GPL(rio_mport_get_efb);
/**
* rio_mport_get_feature - query for devices' extended features
return 0;
}
+EXPORT_SYMBOL_GPL(rio_mport_get_feature);
/**
* rio_get_asm - Begin or continue searching for a RIO device by vid/did/asm_vid/asm_did
#endif /* CONFIG_RAPIDIO_DMA_ENGINE */
+/**
+ * rio_find_mport - find RIO mport by its ID
+ * @mport_id: number (ID) of mport device
+ *
+ * Given a RIO mport number, the desired mport is located
+ * in the global list of mports. If the mport is found, a pointer to its
+ * data structure is returned. If no mport is found, %NULL is returned.
+ */
+struct rio_mport *rio_find_mport(int mport_id)
+{
+ struct rio_mport *port;
+
+ mutex_lock(&rio_mport_list_lock);
+ list_for_each_entry(port, &rio_mports, node) {
+ if (port->id == mport_id)
+ goto found;
+ }
+ port = NULL;
+found:
+ mutex_unlock(&rio_mport_list_lock);
+
+ return port;
+}
+
+/**
+ * rio_register_scan - enumeration/discovery method registration interface
+ * @mport_id: mport device ID for which fabric scan routine has to be set
+ * (RIO_MPORT_ANY = set for all available mports)
+ * @scan_ops: enumeration/discovery control structure
+ *
+ * Assigns enumeration or discovery method to the specified mport device (or all
+ * available mports if RIO_MPORT_ANY is specified).
+ * Returns error if the mport already has an enumerator attached to it.
+ * In case of RIO_MPORT_ANY ignores ports with valid scan routines and returns
+ * an error if was unable to find at least one available mport.
+ */
+int rio_register_scan(int mport_id, struct rio_scan *scan_ops)
+{
+ struct rio_mport *port;
+ int rc = -EBUSY;
+
+ mutex_lock(&rio_mport_list_lock);
+ list_for_each_entry(port, &rio_mports, node) {
+ if (port->id == mport_id || mport_id == RIO_MPORT_ANY) {
+ if (port->nscan && mport_id == RIO_MPORT_ANY)
+ continue;
+ else if (port->nscan)
+ break;
+
+ port->nscan = scan_ops;
+ rc = 0;
+
+ if (mport_id != RIO_MPORT_ANY)
+ break;
+ }
+ }
+ mutex_unlock(&rio_mport_list_lock);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(rio_register_scan);
+
+/**
+ * rio_unregister_scan - removes enumeration/discovery method from mport
+ * @mport_id: mport device ID for which fabric scan routine has to be
+ * unregistered (RIO_MPORT_ANY = set for all available mports)
+ *
+ * Removes enumeration or discovery method assigned to the specified mport
+ * device (or all available mports if RIO_MPORT_ANY is specified).
+ */
+int rio_unregister_scan(int mport_id)
+{
+ struct rio_mport *port;
+
+ mutex_lock(&rio_mport_list_lock);
+ list_for_each_entry(port, &rio_mports, node) {
+ if (port->id == mport_id || mport_id == RIO_MPORT_ANY) {
+ if (port->nscan)
+ port->nscan = NULL;
+ if (mport_id != RIO_MPORT_ANY)
+ break;
+ }
+ }
+ mutex_unlock(&rio_mport_list_lock);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(rio_unregister_scan);
+
static void rio_fixup_device(struct rio_dev *dev)
{
}
work = container_of(_work, struct rio_disc_work, work);
pr_debug("RIO: discovery work for mport %d %s\n",
work->mport->id, work->mport->name);
- rio_disc_mport(work->mport);
+ work->mport->nscan->discover(work->mport, 0);
}
int rio_init_mports(void)
* First, run enumerations and check if we need to perform discovery
* on any of the registered mports.
*/
+ mutex_lock(&rio_mport_list_lock);
list_for_each_entry(port, &rio_mports, node) {
- if (port->host_deviceid >= 0)
- rio_enum_mport(port);
- else
+ if (port->host_deviceid >= 0) {
+ if (port->nscan)
+ port->nscan->enumerate(port, 0);
+ } else
n++;
}
+ mutex_unlock(&rio_mport_list_lock);
if (!n)
goto no_disc;
}
n = 0;
+ mutex_lock(&rio_mport_list_lock);
list_for_each_entry(port, &rio_mports, node) {
- if (port->host_deviceid < 0) {
+ if (port->host_deviceid < 0 && port->nscan) {
work[n].mport = port;
INIT_WORK(&work[n].work, disc_work_handler);
queue_work(rio_wq, &work[n].work);
n++;
}
}
+ mutex_unlock(&rio_mport_list_lock);
flush_workqueue(rio_wq);
pr_debug("RIO: destroy discovery workqueue\n");
return 0;
}
-device_initcall_sync(rio_init_mports);
-
static int hdids[RIO_MAX_MPORTS + 1];
static int rio_get_hdid(int index)
port->id = next_portid++;
port->host_deviceid = rio_get_hdid(port->id);
+ port->nscan = NULL;
+ mutex_lock(&rio_mport_list_lock);
list_add_tail(&port->node, &rio_mports);
+ mutex_unlock(&rio_mport_list_lock);
return 0;
}
EXPORT_SYMBOL_GPL(rio_release_inb_mbox);
EXPORT_SYMBOL_GPL(rio_request_outb_mbox);
EXPORT_SYMBOL_GPL(rio_release_outb_mbox);
+EXPORT_SYMBOL_GPL(rio_init_mports);
#include <linux/rio.h>
#define RIO_MAX_CHK_RETRY 3
+#define RIO_MPORT_ANY (-1)
/* Functions internal to the RIO core code */
extern int rio_mport_chk_dev_access(struct rio_mport *mport, u16 destid,
u8 hopcount);
extern int rio_create_sysfs_dev_files(struct rio_dev *rdev);
-extern int rio_enum_mport(struct rio_mport *mport);
-extern int rio_disc_mport(struct rio_mport *mport);
extern int rio_std_route_add_entry(struct rio_mport *mport, u16 destid,
u8 hopcount, u16 table, u16 route_destid,
u8 route_port);
u8 hopcount, u16 table);
extern int rio_set_port_lockout(struct rio_dev *rdev, u32 pnum, int lock);
extern struct rio_dev *rio_get_comptag(u32 comp_tag, struct rio_dev *from);
+extern int rio_add_device(struct rio_dev *rdev);
+extern void rio_switch_init(struct rio_dev *rdev, int do_enum);
+extern int rio_enable_rx_tx_port(struct rio_mport *port, int local, u16 destid,
+ u8 hopcount, u8 port_num);
+extern int rio_register_scan(int mport_id, struct rio_scan *scan_ops);
+extern int rio_unregister_scan(int mport_id);
+extern void rio_attach_device(struct rio_dev *rdev);
+extern struct rio_mport *rio_find_mport(int mport_id);
/* Structures internal to the RIO core code */
extern struct device_attribute rio_dev_attrs[];
-extern spinlock_t rio_global_list_lock;
+extern struct bus_attribute rio_bus_attrs[];
extern struct rio_switch_ops __start_rio_switch_ops[];
extern struct rio_switch_ops __end_rio_switch_ops[];
info->irq, ret);
dev_info(&pdev->dev, "RTC CHIP NAME: %s\n", pdev->id_entry->name);
- if (pdata->rtc_delay) {
+ if (pdata && pdata->rtc_delay) {
info->lp3974_bug_workaround = true;
dev_warn(&pdev->dev, "LP3974 with RTC REGERR option."
" RTC updates will be extremely slow.\n");
struct pl031_local *ldata = dev_get_drvdata(&adev->dev);
amba_set_drvdata(adev, NULL);
- free_irq(adev->irq[0], ldata->rtc);
+ free_irq(adev->irq[0], ldata);
rtc_device_unregister(ldata->rtc);
iounmap(ldata->base);
kfree(ldata);
source "drivers/staging/iio/Kconfig"
-source "drivers/staging/zram/Kconfig"
-
source "drivers/staging/zsmalloc/Kconfig"
+source "drivers/staging/zram/Kconfig"
+
source "drivers/staging/wlags49_h2/Kconfig"
source "drivers/staging/wlags49_h25/Kconfig"
* 'log->buffer' which contains the first entry readable by 'euid'
*/
static size_t get_next_entry_by_uid(struct logger_log *log,
- size_t off, uid_t euid)
+ size_t off, kuid_t euid)
{
while (off != log->w_off) {
struct logger_entry *entry;
entry = get_entry_header(log, off, &scratch);
- if (entry->euid == euid)
+ if (uid_eq(entry->euid, euid))
return off;
next_len = sizeof(struct logger_entry) + entry->len;
__s32 tid;
__s32 sec;
__s32 nsec;
- uid_t euid;
+ kuid_t euid;
char msg[0];
};
config COMEDI_NI_6527
tristate "NI 6527 support"
+ depends on HAS_DMA
select COMEDI_MITE
---help---
Enable support for the National Instruments 6527 PCI card
config COMEDI_NI_65XX
tristate "NI 65xx static dio PCI card support"
+ depends on HAS_DMA
select COMEDI_MITE
---help---
Enable support for National Instruments 65xx static dio boards.
config COMEDI_NI_660X
tristate "NI 660x counter/timer PCI card support"
+ depends on HAS_DMA
select COMEDI_NI_TIOCMD
---help---
Enable support for National Instruments PCI-6601 (ni_660x), PCI-6602,
config COMEDI_NI_670X
tristate "NI 670x PCI card support"
+ depends on HAS_DMA
select COMEDI_MITE
---help---
Enable support for National Instruments PCI-6703 and PCI-6704
config COMEDI_NI_LABPC_PCI
tristate "NI Lab-PC PCI-1200 support"
+ depends on HAS_DMA
select COMEDI_NI_LABPC
select COMEDI_MITE
---help---
config COMEDI_NI_PCIDIO
tristate "NI PCI-DIO32HS, PCI-6533, PCI-6534 support"
+ depends on HAS_DMA
select COMEDI_MITE
select COMEDI_8255
---help---
config COMEDI_NI_PCIMIO
tristate "NI PCI-MIO-E series and M series support"
+ depends on HAS_DMA
select COMEDI_NI_TIOCMD
select COMEDI_8255
select COMEDI_FC
called ssv_dnp.
config COMEDI_MITE
+ depends on HAS_DMA
tristate
config COMEDI_NI_TIOCMD
tristate
+ depends on HAS_DMA
select COMEDI_NI_TIO
select COMEDI_MITE
clear_bit(PG_reserved,
&(virt_to_page(buf->virt_addr)->flags));
if (s->async_dma_dir != DMA_NONE) {
+#ifdef CONFIG_HAS_DMA
dma_free_coherent(dev->hw_dev,
PAGE_SIZE,
buf->virt_addr,
buf->dma_addr);
+#endif
} else {
free_page((unsigned long)buf->virt_addr);
}
struct comedi_buf_page *buf;
unsigned i;
+ if (!IS_ENABLED(CONFIG_HAS_DMA) && s->async_dma_dir != DMA_NONE) {
+ dev_err(dev->class_dev,
+ "dma buffer allocation not supported\n");
+ return;
+ }
+
async->buf_page_list = vzalloc(sizeof(*buf) * n_pages);
if (async->buf_page_list)
pages = vmalloc(sizeof(struct page *) * n_pages);
for (i = 0; i < n_pages; i++) {
buf = &async->buf_page_list[i];
if (s->async_dma_dir != DMA_NONE)
+#ifdef CONFIG_HAS_DMA
buf->virt_addr = dma_alloc_coherent(dev->hw_dev,
PAGE_SIZE,
&buf->dma_addr,
GFP_KERNEL |
__GFP_COMP);
+#else
+ break;
+#endif
else
buf->virt_addr = (void *)get_zeroed_page(GFP_KERNEL);
if (!buf->virt_addr)
return -EBUSY;
}
- if (!async->prealloc_buf)
- return -EINVAL;
-
/* make sure buffer is an integral number of pages
* (we round up) */
new_size = (new_size + PAGE_SIZE - 1) & PAGE_MASK;
/* clear flip-flop to make sure 2-byte registers for
* count and address get set correctly */
clear_dma_ff(devpriv->dma_chan);
- set_dma_addr(devpriv->dma_chan,
- virt_to_bus(devpriv->dma_buffer));
+ set_dma_addr(devpriv->dma_chan, devpriv->dma_addr);
/* set appropriate size of transfer */
devpriv->dma_transfer_size = labpc_suggest_transfer_size(cmd);
if (cmd->stop_src == TRIG_COUNT &&
devpriv->count -= num_points;
/* set address and count for next transfer */
- set_dma_addr(devpriv->dma_chan, virt_to_bus(devpriv->dma_buffer));
+ set_dma_addr(devpriv->dma_chan, devpriv->dma_addr);
set_dma_count(devpriv->dma_chan, leftover * sample_size);
release_dma_lock(flags);
unsigned long dma_flags;
devpriv->dma_chan = dma_chan;
+ devpriv->dma_addr =
+ virt_to_bus(devpriv->dma_buffer);
+
dma_flags = claim_dma_lock();
disable_dma(devpriv->dma_chan);
set_dma_mode(devpriv->dma_chan, DMA_MODE_READ);
unsigned int divisor_b1;
unsigned int dma_chan; /* dma channel to use */
u16 *dma_buffer; /* buffer ai will dma into */
+ phys_addr_t dma_addr;
/* transfer size in bytes for current transfer */
unsigned int dma_transfer_size;
/* we are using dma/fifo-half-full/etc. */
static int ni_gpct_insn_config(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn, unsigned int *data);
+#ifdef PCIDMA
static int ni_gpct_cmd(struct comedi_device *dev, struct comedi_subdevice *s);
static int ni_gpct_cmdtest(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_cmd *cmd);
+#endif
static int ni_gpct_cancel(struct comedi_device *dev,
struct comedi_subdevice *s);
static void handle_gpct_interrupt(struct comedi_device *dev,
for (j = 0; j < NUM_GPCT; ++j) {
s = &dev->subdevices[NI_GPCT_SUBDEV(j)];
s->type = COMEDI_SUBD_COUNTER;
- s->subdev_flags =
- SDF_READABLE | SDF_WRITABLE | SDF_LSAMPL | SDF_CMD_READ
- /* | SDF_CMD_WRITE */ ;
+ s->subdev_flags = SDF_READABLE | SDF_WRITABLE | SDF_LSAMPL;
s->n_chan = 3;
if (board->reg_type & ni_reg_m_series_mask)
s->maxdata = 0xffffffff;
s->insn_read = &ni_gpct_insn_read;
s->insn_write = &ni_gpct_insn_write;
s->insn_config = &ni_gpct_insn_config;
+#ifdef PCIDMA
+ s->subdev_flags |= SDF_CMD_READ /* | SDF_CMD_WRITE */;
s->do_cmd = &ni_gpct_cmd;
s->len_chanlist = 1;
s->do_cmdtest = &ni_gpct_cmdtest;
s->cancel = &ni_gpct_cancel;
s->async_dma_dir = DMA_BIDIRECTIONAL;
+#endif
s->private = &devpriv->counter_dev->counters[j];
devpriv->counter_dev->counters[j].chip_index = 0;
return ni_tio_winsn(counter, insn, data);
}
+#ifdef PCIDMA
static int ni_gpct_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
{
int retval;
-#ifdef PCIDMA
struct ni_gpct *counter = s->private;
/* const struct comedi_cmd *cmd = &s->async->cmd; */
ni_tio_acknowledge_and_confirm(counter, NULL, NULL, NULL, NULL);
ni_e_series_enable_second_irq(dev, counter->counter_index, 1);
retval = ni_tio_cmd(counter, s->async);
-#else
- retval = -ENOTSUPP;
-#endif
return retval;
}
+#endif
+#ifdef PCIDMA
static int ni_gpct_cmdtest(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_cmd *cmd)
{
-#ifdef PCIDMA
struct ni_gpct *counter = s->private;
return ni_tio_cmdtest(counter, cmd);
-#else
return -ENOTSUPP;
-#endif
}
+#endif
static int ni_gpct_cancel(struct comedi_device *dev, struct comedi_subdevice *s)
{
tristate "DesignWare USB2 DRD Core Support"
depends on USB
depends on VIRT_TO_BUS
- select USB_OTG_UTILS
help
Say Y or M here if your system has a Dual Role HighSpeed
USB controller based on the DesignWare HSOTG IP Core.
bool "Enable Missed SOF Tracking"
help
Say Y here to enable logging of missed SOF events to the dmesg log.
+ WARNING: This feature is still experimental.
If in doubt, say N.
config USB_DWC2_DEBUG_PERIODIC
static void dwc2_track_missed_sofs(struct dwc2_hsotg *hsotg)
{
#ifdef CONFIG_USB_DWC2_TRACK_MISSED_SOFS
-#warning Compiling code to track missed SOFs
-
u16 curr_frame_number = hsotg->frame_number;
if (hsotg->frame_num_idx < FRAME_NUM_ARRAY_SIZE) {
hsotg->dev = &dev->dev;
+ /*
+ * Use reasonable defaults so platforms don't have to provide these.
+ */
+ if (!dev->dev.dma_mask)
+ dev->dev.dma_mask = &dev->dev.coherent_dma_mask;
+ if (!dev->dev.coherent_dma_mask)
+ dev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+
irq = platform_get_irq(dev, 0);
if (irq < 0) {
dev_err(&dev->dev, "missing IRQ resource\n");
config WIMAX_GDM72XX_USB_PM
bool "Enable power managerment support"
- depends on USB_SUSPEND
+ depends on PM_RUNTIME
endif # WIMAX_GDM72XX_USB
static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
{
struct mxs_lradc *lradc = iio_priv(iio);
- struct iio_buffer *buffer = iio->buffer;
int ret = 0, chan, ofs = 0;
unsigned long enable = 0;
uint32_t ctrl4_set = 0;
uint32_t ctrl1_irq = 0;
const uint32_t chan_value = LRADC_CH_ACCUMULATE |
((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
- const int len = bitmap_weight(buffer->scan_mask, LRADC_MAX_TOTAL_CHANS);
+ const int len = bitmap_weight(iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS);
if (!len)
return -EINVAL;
lradc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
writel(0xff, lradc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
- for_each_set_bit(chan, buffer->scan_mask, LRADC_MAX_TOTAL_CHANS) {
+ for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
dev_info(&chip->client->dev,
"%s: i2c device found does not match expected id\n",
__func__);
+ ret = -EINVAL;
goto fail1;
}
if (ret) {
dev_err(&clientp->dev,
"%s: irq request failed", __func__);
- goto fail2;
+ goto fail1;
}
}
if (ret) {
dev_err(&clientp->dev,
"%s: iio registration failed\n", __func__);
- goto fail1;
+ goto fail2;
}
dev_info(&clientp->dev, "%s Light sensor found.\n", id->name);
return 0;
-fail1:
+fail2:
if (clientp->irq)
free_irq(clientp->irq, indio_dev);
-fail2:
+fail1:
iio_device_free(indio_dev);
return ret;
config DRM_IMX
tristate "DRM Support for Freescale i.MX"
select DRM_KMS_HELPER
+ select VIDEOMODE_HELPERS
select DRM_GEM_CMA_HELPER
select DRM_KMS_CMA_HELPER
depends on DRM && (ARCH_MXC || ARCH_MULTIPLATFORM)
config DRM_IMX_PARALLEL_DISPLAY
tristate "Support for parallel displays"
depends on DRM_IMX
+ select VIDEOMODE_HELPERS
config DRM_IMX_TVE
tristate "Support for TV and VGA displays"
depends on DRM_IMX
+ select REGMAP_MMIO
help
Choose this to enable the internal Television Encoder (TVe)
found on i.MX53 processors.
config DRM_IMX_IPUV3_CORE
tristate "IPUv3 core support"
depends on DRM_IMX
+ depends on RESET_CONTROLLER
help
Choose this if you have a i.MX5/6 system and want
to use the IPU. This option only enables IPU base
config DRM_IMX_IPUV3
tristate "DRM Support for i.MX IPUv3"
depends on DRM_IMX
+ depends on DRM_IMX_IPUV3_CORE
help
Choose this if you have a i.MX5 or i.MX6 processor.
tve->dac_reg = devm_regulator_get(&pdev->dev, "dac");
if (!IS_ERR(tve->dac_reg)) {
regulator_set_voltage(tve->dac_reg, 2750000, 2750000);
- regulator_enable(tve->dac_reg);
+ ret = regulator_enable(tve->dac_reg);
+ if (ret)
+ return ret;
}
tve->clk = devm_clk_get(&pdev->dev, "tve");
config SOLO6X10
tristate "Softlogic 6x10 MPEG codec cards"
depends on PCI && VIDEO_DEV && SND && I2C
+ depends on FONTS
select VIDEOBUF2_DMA_SG
select VIDEOBUF2_DMA_CONTIG
select SND_PCM
}
EXPORT_SYMBOL_GPL(nvec_register_notifier);
+/**
+ * nvec_unregister_notifier - Unregister a notifier with nvec
+ * @nvec: A &struct nvec_chip
+ * @nb: The notifier block to unregister
+ *
+ * Unregisters a notifier with @nvec. The notifier will be removed from the
+ * atomic notifier chain.
+ */
+int nvec_unregister_notifier(struct nvec_chip *nvec, struct notifier_block *nb)
+{
+ return atomic_notifier_chain_unregister(&nvec->notifier_list, nb);
+}
+EXPORT_SYMBOL_GPL(nvec_unregister_notifier);
+
/**
* nvec_status_notifier - The final notifier
*
*
* Free the given message
*/
-inline void nvec_msg_free(struct nvec_chip *nvec, struct nvec_msg *msg)
+void nvec_msg_free(struct nvec_chip *nvec, struct nvec_msg *msg)
{
if (msg != &nvec->tx_scratch)
dev_vdbg(nvec->dev, "INFO: Free %ti\n", msg - nvec->msg_pool);
return -ENODEV;
}
- i2c_clk = clk_get(&pdev->dev, "div-clk");
+ i2c_clk = devm_clk_get(&pdev->dev, "div-clk");
if (IS_ERR(i2c_clk)) {
dev_err(nvec->dev, "failed to get controller clock\n");
return -ENODEV;
nvec_toggle_global_events(nvec, false);
mfd_remove_devices(nvec->dev);
+ nvec_unregister_notifier(nvec, &nvec->nvec_status_notifier);
cancel_work_sync(&nvec->rx_work);
cancel_work_sync(&nvec->tx_work);
+ /* FIXME: needs check wether nvec is responsible for power off */
+ pm_power_off = NULL;
return 0;
}
struct notifier_block *nb,
unsigned int events);
-extern int nvec_unregister_notifier(struct device *dev,
- struct notifier_block *nb,
- unsigned int events);
+extern int nvec_unregister_notifier(struct nvec_chip *dev,
+ struct notifier_block *nb);
extern void nvec_msg_free(struct nvec_chip *nvec, struct nvec_msg *msg);
static int nvec_kbd_remove(struct platform_device *pdev)
{
+ struct nvec_chip *nvec = dev_get_drvdata(pdev->dev.parent);
+ char disable_kbd[] = { NVEC_KBD, DISABLE_KBD },
+ uncnfg_wake_key_reporting[] = { NVEC_KBD, CNFG_WAKE_KEY_REPORTING,
+ false };
+ nvec_write_async(nvec, uncnfg_wake_key_reporting, 3);
+ nvec_write_async(nvec, disable_kbd, 2);
+ nvec_unregister_notifier(nvec, &keys_dev.notifier);
+
input_unregister_device(keys_dev.input);
- input_free_device(keys_dev.input);
return 0;
}
MODULE_AUTHOR("Marc Dietrich <marvin24@gmx.de>");
MODULE_DESCRIPTION("NVEC keyboard driver");
+MODULE_ALIAS("platform:nvec-kbd");
MODULE_LICENSE("GPL");
struct nvec_power *power = platform_get_drvdata(pdev);
cancel_delayed_work_sync(&power->poller);
+ nvec_unregister_notifier(power->nvec, &power->notifier);
switch (pdev->id) {
case AC:
power_supply_unregister(&nvec_psy);
struct serio *ser_dev;
char mouse_reset[] = { NVEC_PS2, SEND_COMMAND, PSMOUSE_RST, 3 };
- ser_dev = devm_kzalloc(&pdev->dev, sizeof(struct serio), GFP_KERNEL);
+ ser_dev = kzalloc(sizeof(struct serio), GFP_KERNEL);
if (ser_dev == NULL)
return -ENOMEM;
static int nvec_mouse_remove(struct platform_device *pdev)
{
+ struct nvec_chip *nvec = dev_get_drvdata(pdev->dev.parent);
+
+ ps2_sendcommand(ps2_dev.ser_dev, DISABLE_MOUSE);
+ ps2_stopstreaming(ps2_dev.ser_dev);
+ nvec_unregister_notifier(nvec, &ps2_dev.notifier);
serio_unregister_port(ps2_dev.ser_dev);
return 0;
MODULE_DESCRIPTION("NVEC mouse driver");
MODULE_AUTHOR("Marc Dietrich <marvin24@gmx.de>");
+MODULE_ALIAS("platform:nvec-mouse");
MODULE_LICENSE("GPL");
config DX_SEP
tristate "Discretix SEP driver"
- depends on PCI
+ depends on PCI && CRYPTO
help
Discretix SEP driver; used for the security processor subsystem
on board the Intel Mobile Internet Device and adds SEP availability
unsigned char intr_status;
struct synaptics_rmi4_data *rmi4_data = dev_get_drvdata(dev);
- regulator_enable(rmi4_data->regulator);
+ retval = regulator_enable(rmi4_data->regulator);
+ if (retval) {
+ dev_err(dev, "Regulator enable failed (%d)\n", retval);
+ return retval;
+ }
enable_irq(rmi4_data->i2c_client->irq);
rmi4_data->touch_stopped = false;
DBG_PRT(MSG_LEVEL_DEBUG, KERN_INFO "%s: Netdevice %s unregistered\n",
pDevice->dev->name, pDevice->apdev->name);
}
- kfree(pDevice->apdev);
+ free_netdev(pDevice->apdev);
pDevice->apdev = NULL;
pDevice->bEnable8021x = false;
pDevice->bEnableHostWEP = false;
return rc;
}
+ spin_lock_irq(&pDevice->lock);
+
if (wrq->disabled) {
pDevice->ePSMode = WMAC_POWER_CAM;
PSvDisablePowerSaving(pDevice);
+ spin_unlock_irq(&pDevice->lock);
return rc;
}
if ((wrq->flags & IW_POWER_TYPE) == IW_POWER_TIMEOUT) {
pDevice->ePSMode = WMAC_POWER_FAST;
PSvEnablePowerSaving((void *)pDevice, pMgmt->wListenInterval);
}
+
+ spin_unlock_irq(&pDevice->lock);
+
switch (wrq->flags & IW_POWER_MODE) {
case IW_POWER_UNICAST_R:
DBG_PRT(MSG_LEVEL_DEBUG, KERN_INFO " SIOCSIWPOWER: IW_POWER_UNICAST_R \n");
--- /dev/null
+ RAMSTER HOW-TO
+
+Author: Dan Magenheimer
+Ramster maintainer: Konrad Wilk <konrad.wilk@oracle.com>
+
+This is a HOWTO document for ramster which, as of this writing, is in
+the kernel as a subdirectory of zcache in drivers/staging, called ramster.
+(Zcache can be built with or without ramster functionality.) If enabled
+and properly configured, ramster allows memory capacity load balancing
+across multiple machines in a cluster. Further, the ramster code serves
+as an example of asynchronous access for zcache (as well as cleancache and
+frontswap) that may prove useful for future transcendent memory
+implementations, such as KVM and NVRAM. While ramster works today on
+any network connection that supports kernel sockets, its features may
+become more interesting on future high-speed fabrics/interconnects.
+
+Ramster requires both kernel and userland support. The userland support,
+called ramster-tools, is known to work with EL6-based distros, but is a
+set of poorly-hacked slightly-modified cluster tools based on ocfs2, which
+includes an init file, a config file, and a userland binary that interfaces
+to the kernel. This state of userland support reflects the abysmal userland
+skills of this suitably-embarrassed author; any help/patches to turn
+ramster-tools into more distributable rpms/debs useful for a wider range
+of distros would be appreciated. The source RPM that can be used as a
+starting point is available at:
+ http://oss.oracle.com/projects/tmem/files/RAMster/
+
+As a result of this author's ignorance, userland setup described in this
+HOWTO assumes an EL6 distro and is described in EL6 syntax. Apologies
+if this offends anyone!
+
+Kernel support has only been tested on x86_64. Systems with an active
+ocfs2 filesystem should work, but since ramster leverages a lot of
+code from ocfs2, there may be latent issues. A kernel configuration that
+includes CONFIG_OCFS2_FS should build OK, and should certainly run OK
+if no ocfs2 filesystem is mounted.
+
+This HOWTO demonstrates memory capacity load balancing for a two-node
+cluster, where one node called the "local" node becomes overcommitted
+and the other node called the "remote" node provides additional RAM
+capacity for use by the local node. Ramster is capable of more complex
+topologies; see the last section titled "ADVANCED RAMSTER TOPOLOGIES".
+
+If you find any terms in this HOWTO unfamiliar or don't understand the
+motivation for ramster, the following LWN reading is recommended:
+-- Transcendent Memory in a Nutshell (lwn.net/Articles/454795)
+-- The future calculus of memory management (lwn.net/Articles/475681)
+And since ramster is built on top of zcache, this article may be helpful:
+-- In-kernel memory compression (lwn.net/Articles/545244)
+
+Now that you've memorized the contents of those articles, let's get started!
+
+A. PRELIMINARY
+
+1) Install two x86_64 Linux systems that are known to work when
+ upgraded to a recent upstream Linux kernel version.
+
+On each system:
+
+2) Configure, build and install, then boot Linux, just to ensure it
+ can be done with an unmodified upstream kernel. Confirm you booted
+ the upstream kernel with "uname -a".
+
+3) If you plan to do any performance testing or unless you plan to
+ test only swapping, the "WasActive" patch is also highly recommended.
+ (Search lkml.org for WasActive, apply the patch, rebuild your kernel.)
+ For a demo or simple testing, the patch can be ignored.
+
+4) Install ramster-tools as root. An x86_64 rpm for EL6-based systems
+ can be found at:
+ http://oss.oracle.com/projects/tmem/files/RAMster/
+ (Sorry but for now, non-EL6 users must recreate ramster-tools on
+ their own from source. See above.)
+
+5) Ensure that debugfs is mounted at each boot. Examples below assume it
+ is mounted at /sys/kernel/debug.
+
+B. BUILDING RAMSTER INTO THE KERNEL
+
+Do the following on each system:
+
+1) Using the kernel configuration mechanism of your choice, change
+ your config to include:
+
+ CONFIG_CLEANCACHE=y
+ CONFIG_FRONTSWAP=y
+ CONFIG_STAGING=y
+ CONFIG_CONFIGFS_FS=y # NOTE: MUST BE y, not m
+ CONFIG_ZCACHE=y
+ CONFIG_RAMSTER=y
+
+ For a linux-3.10 or later kernel, you should also set:
+
+ CONFIG_ZCACHE_DEBUG=y
+ CONFIG_RAMSTER_DEBUG=y
+
+ Before building the kernel please doublecheck your kernel config
+ file to ensure all of the settings are correct.
+
+2) Build this kernel and change your boot file (e.g. /etc/grub.conf)
+ so that the new kernel will boot.
+
+3) Add "zcache" and "ramster" as kernel boot parameters for the new kernel.
+
+4) Reboot each system approximately simultaneously.
+
+5) Check dmesg to ensure there are some messages from ramster, prefixed
+ by "ramster:"
+
+ # dmesg | grep ramster
+
+ You should also see a lot of files in:
+
+ # ls /sys/kernel/debug/zcache
+ # ls /sys/kernel/debug/ramster
+
+ These are mostly counters for various zcache and ramster activities.
+ You should also see files in:
+
+ # ls /sys/kernel/mm/ramster
+
+ These are sysfs files that control ramster as we shall see.
+
+ Ramster now will act as a single-system zcache on each system
+ but doesn't yet know anything about the cluster so can't yet do
+ anything remotely.
+
+C. CONFIGURING THE RAMSTER CLUSTER
+
+This part can be error prone unless you are familiar with clustering
+filesystems. We need to describe the cluster in a /etc/ramster.conf
+file and the init scripts that parse it are extremely picky about
+the syntax.
+
+1) Create a /etc/ramster.conf file and ensure it is identical on both
+ systems. This file mimics the ocfs2 format and there is a good amount
+ of documentation that can be searched for ocfs2.conf, but you can use:
+
+ cluster:
+ name = ramster
+ node_count = 2
+ node:
+ name = system1
+ cluster = ramster
+ number = 0
+ ip_address = my.ip.ad.r1
+ ip_port = 7777
+ node:
+ name = system2
+ cluster = ramster
+ number = 1
+ ip_address = my.ip.ad.r2
+ ip_port = 7777
+
+ You must ensure that the "name" field in the file exactly matches
+ the output of "hostname" on each system; if "hostname" shows a
+ fully-qualified hostname, ensure the name is fully qualified in
+ /etc/ramster.conf. Obviously, substitute my.ip.ad.rx with proper
+ ip addresses.
+
+2) Enable the ramster service and configure it. If you used the
+ EL6 ramster-tools, this would be:
+
+ # chkconfig --add ramster
+ # service ramster configure
+
+ Set "load on boot" to "y", cluster to start is "ramster" (or whatever
+ name you chose in ramster.conf), heartbeat dead threshold as "500",
+ network idle timeout as "1000000". Leave the others as default.
+
+3) Reboot both systems. After reboot, try (assuming EL6 ramster-tools):
+
+ # service ramster status
+
+ You should see "Checking RAMSTER cluster "ramster": Online". If you do
+ not, something is wrong and ramster will not work. Note that you
+ should also see that the driver for "configfs" is loaded and mounted,
+ the driver for ocfs2_dlmfs is not loaded, and some numbers for network
+ parameters. You will also see "Checking RAMSTER heartbeat: Not active".
+ That's all OK.
+
+4) Now you need to start the cluster heartbeat; the cluster is not "up"
+ until all nodes detect a heartbeat. In a real cluster, heartbeat detection
+ is done via a cluster filesystem, but ramster doesn't require one. Some
+ hack-y kernel code in ramster can start the heartbeat for you though if
+ you tell it what nodes are "up". To enable the heartbeat, do:
+
+ # echo 0 > /sys/kernel/mm/ramster/manual_node_up
+ # echo 1 > /sys/kernel/mm/ramster/manual_node_up
+
+ This must be done on BOTH nodes and, to avoid timeouts, must be done
+ approximately concurrently on both nodes. On an EL6 system, it is
+ convenient to put these lines in /etc/rc.local. To confirm that the
+ cluster is now up, on both systems do:
+
+ # dmesg | grep ramster
+
+ You should see ramster "Accepted connection" messages in dmesg on both
+ nodes after this. Note that if you check userland status again with
+
+ # service ramster status
+
+ you will still see "Checking RAMSTER heartbeat: Not active". That's
+ still OK... the ramster kernel heartbeat hack doesn't communicate to
+ userland.
+
+5) You now must tell each node the node to which it should "remotify" pages.
+ On this two node cluster, we will assume the "local" node, node 0, has
+ memory overcommitted and will use ramster to utilize RAM capacity on
+ the "remote node", node 1. To configure this, on node 0, you do:
+
+ # echo 1 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+ You should see "ramster: node 1 set as remotification target" in dmesg
+ on node 0. Again, on EL6, /etc/rc.local is a good place to put this
+ on node 0 so you don't forget to do it at each boot.
+
+6) One more step: By default, the ramster code does not "remotify" any
+ pages; this is primarily for testing purposes, but sometimes it is
+ useful. This may change in the future, but for now, on node 0, you do:
+
+ # echo 1 > /sys/kernel/mm/ramster/pers_remotify_enable
+ # echo 1 > /sys/kernel/mm/ramster/eph_remotify_enable
+
+ The first enables remotifying swap (persistent, aka frontswap) pages,
+ the second enables remotifying of page cache (ephemeral, cleancache)
+ pages.
+
+ On EL6, these lines can also be put in /etc/rc.local (AFTER the
+ node_up lines), or at the beginning of a script that runs a workload.
+
+7) Note that most testing has been done with both/all machines booted
+ roughly simultaneously to avoid cluster timeouts. Ideally, you should
+ do this too unless you are trying to break ramster rather than just
+ use it. ;-)
+
+D. TESTING RAMSTER
+
+1) Note that ramster has no value unless pages get "remotified". For
+ swap/frontswap/persistent pages, this doesn't happen unless/until
+ the workload would cause swapping to occur, at which point pages
+ are put into frontswap/zcache, and the remotification thread starts
+ working. To get to the point where the system swaps, you either
+ need a workload for which the working set exceeds the RAM in the
+ system; or you need to somehow reduce the amount of RAM one of
+ the system sees. This latter is easy when testing in a VM, but
+ harder on physical systems. In some cases, "mem=xxxM" on the
+ kernel command line restricts memory, but for some values of xxx
+ the kernel may fail to boot. One may also try creating a fixed
+ RAMdisk, doing nothing with it, but ensuring that it eats up a fixed
+ amount of RAM.
+
+2) To see if ramster is working, on the "remote node", node 1, try:
+
+ # grep . /sys/kernel/debug/ramster/foreign_*
+ # # note, that is space-dot-space between grep and the pathname
+
+ to monitor the number (and max) ephemeral and persistent pages
+ that ramster has sent. If these stay at zero, ramster is not working
+ either because the workload on the local node (node 0) isn't creating
+ enough memory pressure or because "remotifying" isn't working. On the
+ local system, node 0, you can watch lots of useful information also.
+ Try:
+
+ grep . /sys/kernel/debug/zcache/*pageframes* \
+ /sys/kernel/debug/zcache/*zbytes* \
+ /sys/kernel/debug/zcache/*zpages* \
+ /sys/kernel/debug/ramster/*remote*
+
+ Of particular note are the remote_*_pages_succ_get counters. These
+ show how many disk reads and/or disk writes have been avoided on the
+ overcommitted local system by storing pages remotely using ramster.
+
+ At the risk of information overload, you can also grep:
+
+ /sys/kernel/debug/cleancache/* and /sys/kernel/debug/frontswap/*
+
+ These show, for example, how many disk reads and/or disk writes have
+ been avoided by using zcache to optimize RAM on the local system.
+
+
+AUTOMATIC SWAP REPATRIATION
+
+You may notice that while the systems are idle, the foreign persistent
+page count on the remote machine slowly decreases. This is because
+ramster implements "frontswap selfshrinking": When possible, swap
+pages that have been remotified are slowly repatriated to the local
+machine. This is so that local RAM can be used when possible and
+so that, in case of remote machine crash, the probability of loss
+of data is reduced.
+
+REBOOTING / POWEROFF
+
+If a system is shut down while some of its swap pages still reside
+on a remote system, the system may lock up during the shutdown
+sequence. This will occur if the network is shut down before the
+swap mechansim is shut down, which is the default ordering on many
+distros. To avoid this annoying problem, simply shut off the swap
+subsystem before starting the shutdown sequence, e.g.:
+
+ # swapoff -a
+ # reboot
+
+Ideally, this swapoff-before-ifdown ordering should be enforced permanently
+using shutdown scripts.
+
+KNOWN PROBLEMS
+
+1) You may periodically see messages such as:
+
+ ramster_r2net, message length problem
+
+ This is harmless but indicates that a node is sending messages
+ containing compressed pages that exceed the maximum for zcache
+ (PAGE_SIZE*15/16). The sender side needs to be fixed.
+
+2) If you see a "No longer connected to node..." message or a "No connection
+ established with node X after N seconds", it is possible you may
+ be in an unrecoverable state. If you are certain all of the
+ appropriate cluster configuration steps described above have been
+ performed, try rebooting the two servers concurrently to see if
+ the cluster starts.
+
+ Note that "Connection to node... shutdown, state 7" is an intermediate
+ connection state. As long as you later see "Accepted connection", the
+ intermediate states are harmless.
+
+3) There are known issues in counting certain values. As a result
+ you may see periodic warnings from the kernel. Almost always you
+ will see "ramster: bad accounting for XXX". There are also "WARN_ONCE"
+ messages. If you see kernel warnings with a tombstone, please report
+ them. They are harmless but reflect bugs that need to be eventually fixed.
+
+ADVANCED RAMSTER TOPOLOGIES
+
+The kernel code for ramster can support up to eight nodes in a cluster,
+but no testing has been done with more than three nodes.
+
+In the example described above, the "remote" node serves as a RAM
+overflow for the "local" node. This can be made symmetric by appropriate
+settings of the sysfs remote_target_nodenum file. For example, by setting:
+
+ # echo 1 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 0, and
+
+ # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 1, each node can serve as a RAM overflow for the other.
+
+For more than two nodes, a "RAM server" can be configured. For a
+three node system, set:
+
+ # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 1, and
+
+ # echo 0 > /sys/kernel/mm/ramster/remote_target_nodenum
+
+on node 2. Then node 0 is a RAM server for node 1 and node 2.
+
+In this implementation of ramster, any remote node is potentially a single
+point of failure (SPOF). Though the probability of failure is reduced
+by automatic swap repatriation (see above), a proposed future enhancement
+to ramster improves high-availability for the cluster by sending a copy
+of each page of date to two other nodes. Patches welcome!
#ifdef CONFIG_ZCACHE_MODULE
#ifdef CONFIG_RAMSTER
-module_param(ramster_enabled, int, S_IRUGO);
+module_param(ramster_enabled, bool, S_IRUGO);
module_param(disable_frontswap_selfshrink, int, S_IRUGO);
#endif
-module_param(disable_cleancache, int, S_IRUGO);
-module_param(disable_frontswap, int, S_IRUGO);
+module_param(disable_cleancache, bool, S_IRUGO);
+module_param(disable_frontswap, bool, S_IRUGO);
#ifdef FRONTSWAP_HAS_EXCLUSIVE_GETS
module_param(frontswap_has_exclusive_gets, bool, S_IRUGO);
#endif
-module_param(disable_frontswap_ignore_nonactive, int, S_IRUGO);
+module_param(disable_frontswap_ignore_nonactive, bool, S_IRUGO);
module_param(zcache_comp_name, charp, S_IRUGO);
module_init(zcache_init);
MODULE_LICENSE("GPL");
*/
static void __exit ehv_bc_exit(void)
{
+ platform_driver_unregister(&ehv_bc_tty_driver);
tty_unregister_driver(ehv_bc_driver);
put_tty_driver(ehv_bc_driver);
kfree(bcs);
if (ip->type == PORT_16550A)
me->fifo[p] = 1;
- opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
- opmode &= OP_MODE_MASK;
+ if (ip->board->chip_flag == MOXA_MUST_MU860_HWID) {
+ opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
+ opmode &= OP_MODE_MASK;
+ } else {
+ opmode = RS232_MODE;
+ }
me->iftype[p] = opmode;
mutex_unlock(&port->mutex);
}
int shiftbit;
unsigned char val, mask;
+ if (info->board->chip_flag != MOXA_MUST_MU860_HWID)
+ return -EFAULT;
+
p = tty->index % 4;
if (cmd == MOXA_SET_OP_MODE) {
if (get_user(opmode, (int __user *) argp))
ldata->real_raw = 0;
}
n_tty_set_room(tty);
+ /*
+ * Fix tty hang when I_IXON(tty) is cleared, but the tty
+ * been stopped by STOP_CHAR(tty) before it.
+ */
+ if (!I_IXON(tty) && old && (old->c_iflag & IXON) && !tty->flow_stopped) {
+ start_tty(tty);
+ }
+
/* The termios change make the tty ready for I/O */
wake_up_interruptible(&tty->write_wait);
wake_up_interruptible(&tty->read_wait);
AIOP_INTR_BIT_3
};
+#ifdef CONFIG_PCI
static Word_t upci_aiop_intr_bits[AIOP_CTL_SIZE] = {
UPCI_AIOP_INTR_BIT_0,
UPCI_AIOP_INTR_BIT_1,
UPCI_AIOP_INTR_BIT_2,
UPCI_AIOP_INTR_BIT_3
};
+#endif
static Byte_t RData[RDATASIZE] = {
0x00, 0x09, 0xf6, 0x82,
static int __init init_ISA(int i);
static void rp_wait_until_sent(struct tty_struct *tty, int timeout);
static void rp_flush_buffer(struct tty_struct *tty);
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model);
static unsigned char GetLineNumber(int ctrl, int aiop, int ch);
static unsigned char SetLineNumber(int ctrl, int aiop, int ch);
static void rp_start(struct tty_struct *tty);
static void sModemReset(CONTROLLER_T * CtlP, int chan, int on);
static void sPCIModemReset(CONTROLLER_T * CtlP, int chan, int on);
static int sWriteTxPrioByte(CHANNEL_T * ChP, Byte_t Data);
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd);
static int sInitController(CONTROLLER_T * CtlP, int CtlNum, ByteIO_t MudbacIO,
ByteIO_t * AiopIOList, int AiopIOListSize,
int IRQNum, Byte_t Frequency, int PeriodicOnly);
};
MODULE_DEVICE_TABLE(pci, rocket_pci_ids);
+/* Resets the speaker controller on RocketModem II and III devices */
+static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
+{
+ ByteIO_t addr;
+
+ /* RocketModem II speaker control is at the 8th port location of offset 0x40 */
+ if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
+ addr = CtlP->AiopIO[0] + 0x4F;
+ sOutB(addr, 0);
+ }
+
+ /* RocketModem III speaker control is at the 1st port location of offset 0x80 */
+ if ((model == MODEL_UPCI_RM3_8PORT)
+ || (model == MODEL_UPCI_RM3_4PORT)) {
+ addr = CtlP->AiopIO[0] + 0x88;
+ sOutB(addr, 0);
+ }
+}
+
+/***************************************************************************
+Function: sPCIInitController
+Purpose: Initialization of controller global registers and controller
+ structure.
+Call: sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
+ IRQNum,Frequency,PeriodicOnly)
+ CONTROLLER_T *CtlP; Ptr to controller structure
+ int CtlNum; Controller number
+ ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
+ This list must be in the order the AIOPs will be found on the
+ controller. Once an AIOP in the list is not found, it is
+ assumed that there are no more AIOPs on the controller.
+ int AiopIOListSize; Number of addresses in AiopIOList
+ int IRQNum; Interrupt Request number. Can be any of the following:
+ 0: Disable global interrupts
+ 3: IRQ 3
+ 4: IRQ 4
+ 5: IRQ 5
+ 9: IRQ 9
+ 10: IRQ 10
+ 11: IRQ 11
+ 12: IRQ 12
+ 15: IRQ 15
+ Byte_t Frequency: A flag identifying the frequency
+ of the periodic interrupt, can be any one of the following:
+ FREQ_DIS - periodic interrupt disabled
+ FREQ_137HZ - 137 Hertz
+ FREQ_69HZ - 69 Hertz
+ FREQ_34HZ - 34 Hertz
+ FREQ_17HZ - 17 Hertz
+ FREQ_9HZ - 9 Hertz
+ FREQ_4HZ - 4 Hertz
+ If IRQNum is set to 0 the Frequency parameter is
+ overidden, it is forced to a value of FREQ_DIS.
+ int PeriodicOnly: 1 if all interrupts except the periodic
+ interrupt are to be blocked.
+ 0 is both the periodic interrupt and
+ other channel interrupts are allowed.
+ If IRQNum is set to 0 the PeriodicOnly parameter is
+ overidden, it is forced to a value of 0.
+Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
+ initialization failed.
+
+Comments:
+ If periodic interrupts are to be disabled but AIOP interrupts
+ are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
+
+ If interrupts are to be completely disabled set IRQNum to 0.
+
+ Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
+ invalid combination.
+
+ This function performs initialization of global interrupt modes,
+ but it does not actually enable global interrupts. To enable
+ and disable global interrupts use functions sEnGlobalInt() and
+ sDisGlobalInt(). Enabling of global interrupts is normally not
+ done until all other initializations are complete.
+
+ Even if interrupts are globally enabled, they must also be
+ individually enabled for each channel that is to generate
+ interrupts.
+
+Warnings: No range checking on any of the parameters is done.
+
+ No context switches are allowed while executing this function.
+
+ After this function all AIOPs on the controller are disabled,
+ they can be enabled with sEnAiop().
+*/
+static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
+ ByteIO_t * AiopIOList, int AiopIOListSize,
+ WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
+ int PeriodicOnly, int altChanRingIndicator,
+ int UPCIRingInd)
+{
+ int i;
+ ByteIO_t io;
+
+ CtlP->AltChanRingIndicator = altChanRingIndicator;
+ CtlP->UPCIRingInd = UPCIRingInd;
+ CtlP->CtlNum = CtlNum;
+ CtlP->CtlID = CTLID_0001; /* controller release 1 */
+ CtlP->BusType = isPCI; /* controller release 1 */
+
+ if (ConfigIO) {
+ CtlP->isUPCI = 1;
+ CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
+ CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
+ CtlP->AiopIntrBits = upci_aiop_intr_bits;
+ } else {
+ CtlP->isUPCI = 0;
+ CtlP->PCIIO =
+ (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
+ CtlP->AiopIntrBits = aiop_intr_bits;
+ }
+
+ sPCIControllerEOI(CtlP); /* clear EOI if warm init */
+ /* Init AIOPs */
+ CtlP->NumAiop = 0;
+ for (i = 0; i < AiopIOListSize; i++) {
+ io = AiopIOList[i];
+ CtlP->AiopIO[i] = (WordIO_t) io;
+ CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
+
+ CtlP->AiopID[i] = sReadAiopID(io); /* read AIOP ID */
+ if (CtlP->AiopID[i] == AIOPID_NULL) /* if AIOP does not exist */
+ break; /* done looking for AIOPs */
+
+ CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io); /* num channels in AIOP */
+ sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE); /* clock prescaler */
+ sOutB(io + _INDX_DATA, sClockPrescale);
+ CtlP->NumAiop++; /* bump count of AIOPs */
+ }
+
+ if (CtlP->NumAiop == 0)
+ return (-1);
+ else
+ return (CtlP->NumAiop);
+}
+
/*
* Called when a PCI card is found. Retrieves and stores model information,
* init's aiopic and serial port hardware.
return (CtlP->NumAiop);
}
-#ifdef CONFIG_PCI
-/***************************************************************************
-Function: sPCIInitController
-Purpose: Initialization of controller global registers and controller
- structure.
-Call: sPCIInitController(CtlP,CtlNum,AiopIOList,AiopIOListSize,
- IRQNum,Frequency,PeriodicOnly)
- CONTROLLER_T *CtlP; Ptr to controller structure
- int CtlNum; Controller number
- ByteIO_t *AiopIOList; List of I/O addresses for each AIOP.
- This list must be in the order the AIOPs will be found on the
- controller. Once an AIOP in the list is not found, it is
- assumed that there are no more AIOPs on the controller.
- int AiopIOListSize; Number of addresses in AiopIOList
- int IRQNum; Interrupt Request number. Can be any of the following:
- 0: Disable global interrupts
- 3: IRQ 3
- 4: IRQ 4
- 5: IRQ 5
- 9: IRQ 9
- 10: IRQ 10
- 11: IRQ 11
- 12: IRQ 12
- 15: IRQ 15
- Byte_t Frequency: A flag identifying the frequency
- of the periodic interrupt, can be any one of the following:
- FREQ_DIS - periodic interrupt disabled
- FREQ_137HZ - 137 Hertz
- FREQ_69HZ - 69 Hertz
- FREQ_34HZ - 34 Hertz
- FREQ_17HZ - 17 Hertz
- FREQ_9HZ - 9 Hertz
- FREQ_4HZ - 4 Hertz
- If IRQNum is set to 0 the Frequency parameter is
- overidden, it is forced to a value of FREQ_DIS.
- int PeriodicOnly: 1 if all interrupts except the periodic
- interrupt are to be blocked.
- 0 is both the periodic interrupt and
- other channel interrupts are allowed.
- If IRQNum is set to 0 the PeriodicOnly parameter is
- overidden, it is forced to a value of 0.
-Return: int: Number of AIOPs on the controller, or CTLID_NULL if controller
- initialization failed.
-
-Comments:
- If periodic interrupts are to be disabled but AIOP interrupts
- are allowed, set Frequency to FREQ_DIS and PeriodicOnly to 0.
-
- If interrupts are to be completely disabled set IRQNum to 0.
-
- Setting Frequency to FREQ_DIS and PeriodicOnly to 1 is an
- invalid combination.
-
- This function performs initialization of global interrupt modes,
- but it does not actually enable global interrupts. To enable
- and disable global interrupts use functions sEnGlobalInt() and
- sDisGlobalInt(). Enabling of global interrupts is normally not
- done until all other initializations are complete.
-
- Even if interrupts are globally enabled, they must also be
- individually enabled for each channel that is to generate
- interrupts.
-
-Warnings: No range checking on any of the parameters is done.
-
- No context switches are allowed while executing this function.
-
- After this function all AIOPs on the controller are disabled,
- they can be enabled with sEnAiop().
-*/
-static int sPCIInitController(CONTROLLER_T * CtlP, int CtlNum,
- ByteIO_t * AiopIOList, int AiopIOListSize,
- WordIO_t ConfigIO, int IRQNum, Byte_t Frequency,
- int PeriodicOnly, int altChanRingIndicator,
- int UPCIRingInd)
-{
- int i;
- ByteIO_t io;
-
- CtlP->AltChanRingIndicator = altChanRingIndicator;
- CtlP->UPCIRingInd = UPCIRingInd;
- CtlP->CtlNum = CtlNum;
- CtlP->CtlID = CTLID_0001; /* controller release 1 */
- CtlP->BusType = isPCI; /* controller release 1 */
-
- if (ConfigIO) {
- CtlP->isUPCI = 1;
- CtlP->PCIIO = ConfigIO + _PCI_9030_INT_CTRL;
- CtlP->PCIIO2 = ConfigIO + _PCI_9030_GPIO_CTRL;
- CtlP->AiopIntrBits = upci_aiop_intr_bits;
- } else {
- CtlP->isUPCI = 0;
- CtlP->PCIIO =
- (WordIO_t) ((ByteIO_t) AiopIOList[0] + _PCI_INT_FUNC);
- CtlP->AiopIntrBits = aiop_intr_bits;
- }
-
- sPCIControllerEOI(CtlP); /* clear EOI if warm init */
- /* Init AIOPs */
- CtlP->NumAiop = 0;
- for (i = 0; i < AiopIOListSize; i++) {
- io = AiopIOList[i];
- CtlP->AiopIO[i] = (WordIO_t) io;
- CtlP->AiopIntChanIO[i] = io + _INT_CHAN;
-
- CtlP->AiopID[i] = sReadAiopID(io); /* read AIOP ID */
- if (CtlP->AiopID[i] == AIOPID_NULL) /* if AIOP does not exist */
- break; /* done looking for AIOPs */
-
- CtlP->AiopNumChan[i] = sReadAiopNumChan((WordIO_t) io); /* num channels in AIOP */
- sOutW((WordIO_t) io + _INDX_ADDR, _CLK_PRE); /* clock prescaler */
- sOutB(io + _INDX_DATA, sClockPrescale);
- CtlP->NumAiop++; /* bump count of AIOPs */
- }
-
- if (CtlP->NumAiop == 0)
- return (-1);
- else
- return (CtlP->NumAiop);
-}
-
-/* Resets the speaker controller on RocketModem II and III devices */
-static void rmSpeakerReset(CONTROLLER_T * CtlP, unsigned long model)
-{
- ByteIO_t addr;
-
- /* RocketModem II speaker control is at the 8th port location of offset 0x40 */
- if ((model == MODEL_RP4M) || (model == MODEL_RP6M)) {
- addr = CtlP->AiopIO[0] + 0x4F;
- sOutB(addr, 0);
- }
-
- /* RocketModem III speaker control is at the 1st port location of offset 0x80 */
- if ((model == MODEL_UPCI_RM3_8PORT)
- || (model == MODEL_UPCI_RM3_4PORT)) {
- addr = CtlP->AiopIO[0] + 0x88;
- sOutB(addr, 0);
- }
-}
-#endif
-
/***************************************************************************
Function: sReadAiopID
Purpose: Read the AIOP idenfication number directly from an AIOP.
{
struct dw8250_data *data = dev_get_drvdata(dev);
- clk_disable_unprepare(data->clk);
+ if (!IS_ERR(data->clk))
+ clk_disable_unprepare(data->clk);
return 0;
}
{
struct dw8250_data *data = dev_get_drvdata(dev);
- clk_prepare_enable(data->clk);
+ if (!IS_ERR(data->clk))
+ clk_prepare_enable(data->clk);
return 0;
}
static const struct acpi_device_id dw8250_acpi_match[] = {
{ "INT33C4", 0 },
{ "INT33C5", 0 },
+ { "80860F0A", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
dmaengine_slave_config(chan, &rx_conf);
uap->dmarx.chan = chan;
- if (plat->dma_rx_poll_enable) {
+ if (plat && plat->dma_rx_poll_enable) {
/* Set poll rate if specified. */
if (plat->dma_rx_poll_rate) {
uap->dmarx.auto_poll_rate = false;
if (rc)
return rc;
rc = platform_driver_register(&mcf_platform_driver);
- if (rc)
+ if (rc) {
+ uart_unregister_driver(&mcf_driver);
return rc;
+ }
return 0;
}
if (psc_ops && psc_ops->fifoc_init) {
ret = psc_ops->fifoc_init();
if (ret)
- return ret;
+ goto err_init;
}
ret = platform_driver_register(&mpc52xx_uart_of_driver);
if (ret) {
printk(KERN_ERR "%s: platform_driver_register failed (%i)\n",
__FILE__, ret);
- uart_unregister_driver(&mpc52xx_uart_driver);
- return ret;
+ goto err_reg;
}
return 0;
+err_reg:
+ if (psc_ops && psc_ops->fifoc_uninit)
+ psc_ops->fifoc_uninit();
+err_init:
+ uart_unregister_driver(&mpc52xx_uart_driver);
+ return ret;
}
static void __exit
dcr_write(up->dcr_host, UART_IER, up->ier);
/* free irq */
- free_irq(up->port.irq, port);
+ free_irq(up->port.irq, up);
}
static int nwpserial_verify_port(struct uart_port *port,
return pdata->get_context_loss_count(up->dev);
}
-static void serial_omap_set_forceidle(struct uart_omap_port *up)
-{
- struct omap_uart_port_info *pdata = up->dev->platform_data;
-
- if (!pdata || !pdata->set_forceidle)
- return;
-
- pdata->set_forceidle(up->dev);
-}
-
-static void serial_omap_set_noidle(struct uart_omap_port *up)
-{
- struct omap_uart_port_info *pdata = up->dev->platform_data;
-
- if (!pdata || !pdata->set_noidle)
- return;
-
- pdata->set_noidle(up->dev);
-}
-
static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
{
struct omap_uart_port_info *pdata = up->dev->platform_data;
serial_out(up, UART_IER, up->ier);
}
- serial_omap_set_forceidle(up);
-
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
}
pm_runtime_get_sync(up->dev);
serial_omap_enable_ier_thri(up);
- serial_omap_set_noidle(up);
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
}
static void __exit s3c24xx_serial_modexit(void)
{
+ platform_driver_unregister(&samsung_serial_driver);
uart_unregister_driver(&s3c24xx_uart_drv);
}
con_set_default_unimap(vc);
vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL);
if (!vc->vc_screenbuf) {
- tty_port_destroy(&vc->port);
kfree(vc);
vc_cons[currcons].d = NULL;
return -ENOMEM;
return ret;
}
-void vc_deallocate(unsigned int currcons)
+struct vc_data *vc_deallocate(unsigned int currcons)
{
+ struct vc_data *vc = NULL;
+
WARN_CONSOLE_UNLOCKED();
if (vc_cons_allocated(currcons)) {
- struct vc_data *vc = vc_cons[currcons].d;
- struct vt_notifier_param param = { .vc = vc };
+ struct vt_notifier_param param;
+ param.vc = vc = vc_cons[currcons].d;
atomic_notifier_call_chain(&vt_notifier_list, VT_DEALLOCATE, ¶m);
vcs_remove_sysfs(currcons);
vc->vc_sw->con_deinit(vc);
put_pid(vc->vt_pid);
module_put(vc->vc_sw->owner);
kfree(vc->vc_screenbuf);
- if (currcons >= MIN_NR_CONSOLES) {
- tty_port_destroy(&vc->port);
- kfree(vc);
- }
vc_cons[currcons].d = NULL;
}
+ return vc;
}
/*
return 0;
}
+/* deallocate a single console, if possible (leave 0) */
+static int vt_disallocate(unsigned int vc_num)
+{
+ struct vc_data *vc = NULL;
+ int ret = 0;
+
+ if (!vc_num)
+ return 0;
+
+ console_lock();
+ if (VT_BUSY(vc_num))
+ ret = -EBUSY;
+ else
+ vc = vc_deallocate(vc_num);
+ console_unlock();
+
+ if (vc && vc_num >= MIN_NR_CONSOLES) {
+ tty_port_destroy(&vc->port);
+ kfree(vc);
+ }
+
+ return ret;
+}
+
+/* deallocate all unused consoles, but leave 0 */
+static void vt_disallocate_all(void)
+{
+ struct vc_data *vc[MAX_NR_CONSOLES];
+ int i;
+
+ console_lock();
+ for (i = 1; i < MAX_NR_CONSOLES; i++)
+ if (!VT_BUSY(i))
+ vc[i] = vc_deallocate(i);
+ else
+ vc[i] = NULL;
+ console_unlock();
+
+ for (i = 1; i < MAX_NR_CONSOLES; i++) {
+ if (vc[i] && i >= MIN_NR_CONSOLES) {
+ tty_port_destroy(&vc[i]->port);
+ kfree(vc[i]);
+ }
+ }
+}
/*
ret = -ENXIO;
break;
}
- if (arg == 0) {
- /* deallocate all unused consoles, but leave 0 */
- console_lock();
- for (i=1; i<MAX_NR_CONSOLES; i++)
- if (! VT_BUSY(i))
- vc_deallocate(i);
- console_unlock();
- } else {
- /* deallocate a single console, if possible */
- arg--;
- if (VT_BUSY(arg))
- ret = -EBUSY;
- else if (arg) { /* leave 0 */
- console_lock();
- vc_deallocate(arg);
- console_unlock();
- }
- }
+ if (arg == 0)
+ vt_disallocate_all();
+ else
+ ret = vt_disallocate(--arg);
break;
case VT_RESIZE:
config UIO_DMEM_GENIRQ
tristate "Userspace platform driver with generic irq and dynamic memory"
+ depends on HAS_DMA
help
Platform driver for Userspace I/O devices, including generic
interrupt handling code. Shared interrupts are not supported.
{
int ret, len;
__le32 *buf;
- int offb, offd;
+ int offb;
+ unsigned int offd;
const int stride = CMD_PACKET_SIZE / (4 * 2) - 1;
int buflen = ((size - 1) / stride + 1 + size * 2) * 4;
config USB_CHIPIDEA_HOST
bool "ChipIdea host controller"
depends on USB=y || USB=USB_CHIPIDEA
- depends on USB_EHCI_HCD
+ depends on USB_EHCI_HCD=y
select USB_EHCI_ROOT_HUB_TT
help
Say Y here to enable host controller functionality of the
ci13xxx_imx_platdata.phy = data->phy;
- if (!pdev->dev.dma_mask) {
- pdev->dev.dma_mask = devm_kzalloc(&pdev->dev,
- sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
- if (!pdev->dev.dma_mask) {
- ret = -ENOMEM;
- dev_err(&pdev->dev, "Failed to alloc dma_mask!\n");
- goto err;
- }
- *pdev->dev.dma_mask = DMA_BIT_MASK(32);
- dma_set_coherent_mask(&pdev->dev, *pdev->dev.dma_mask);
- }
+ if (!pdev->dev.dma_mask)
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (usbmisc_ops && usbmisc_ops->init) {
ret = usbmisc_ops->init(&pdev->dev);
config USB_OTG
bool "OTG support"
- depends on USB_SUSPEND
+ depends on PM_RUNTIME
default n
help
The most notable feature of USB OTG is support for a
/* Edirol SD-20 */
{ USB_DEVICE(0x0582, 0x0027), .driver_info = USB_QUIRK_RESET_RESUME },
+ /* Alcor Micro Corp. Hub */
+ { USB_DEVICE(0x058f, 0x9254), .driver_info = USB_QUIRK_RESET_RESUME },
+
/* appletouch */
{ USB_DEVICE(0x05ac, 0x021a), .driver_info = USB_QUIRK_RESET_RESUME },
config USB_DWC3_HOST
bool "Host only mode"
- depends on USB
+ depends on USB=y || USB=USB_DWC3
help
Select this when you want to use DWC3 in host mode only,
thereby the gadget feature will be regressed.
config USB_DWC3_GADGET
bool "Gadget only mode"
- depends on USB_GADGET
+ depends on USB_GADGET=y || USB_GADGET=USB_DWC3
help
Select this when you want to use DWC3 in gadget mode only,
thereby the host feature will be regressed.
config USB_DWC3_DUAL_ROLE
bool "Dual Role mode"
- depends on (USB && USB_GADGET)
+ depends on ((USB=y || USB=USB_DWC3) && (USB_GADGET=y || USB_GADGET=USB_DWC3))
help
This is the default mode of working of DWC3 controller where
both host and gadget features are enabled.
return 0;
}
-static u64 dwc3_exynos_dma_mask = DMA_BIT_MASK(32);
-
static int dwc3_exynos_probe(struct platform_device *pdev)
{
struct dwc3_exynos *exynos;
* Once we move to full device tree support this will vanish off.
*/
if (!dev->dma_mask)
- dev->dma_mask = &dwc3_exynos_dma_mask;
+ dev->dma_mask = &dev->coherent_dma_mask;
+ if (!dev->coherent_dma_mask)
+ dev->coherent_dma_mask = DMA_BIT_MASK(32);
platform_set_drvdata(pdev, exynos);
depends on ARCH_LPC32XX
depends on USB_PHY
select USB_ISP1301
- select USB_OTG_UTILS
help
This option selects the USB device controller in the LPC32xx SoC.
err_get_hclk:
clk_put(pclk);
- platform_set_drvdata(pdev, NULL);
-
return ret;
}
usb_del_gadget_udc(&udc->gadget);
BUG_ON(udc->driver);
- platform_set_drvdata(pdev, NULL);
bcm63xx_uninit_udc_hw(udc);
return 0;
gi->gstrings[i] = NULL;
s = usb_gstrings_attach(&gi->cdev, gi->gstrings,
USB_GADGET_FIRST_AVAIL_IDX);
- if (IS_ERR(s))
+ if (IS_ERR(s)) {
+ ret = PTR_ERR(s);
goto err_comp_cleanup;
+ }
gi->cdev.desc.iManufacturer = s[USB_GADGET_MANUFACTURER_IDX].id;
gi->cdev.desc.iProduct = s[USB_GADGET_PRODUCT_IDX].id;
}
cfg->gstrings[i] = NULL;
s = usb_gstrings_attach(&gi->cdev, cfg->gstrings, 1);
- if (IS_ERR(s))
+ if (IS_ERR(s)) {
+ ret = PTR_ERR(s);
goto err_comp_cleanup;
+ }
c->iConfiguration = s[0].id;
}
struct dummy *dum = platform_get_drvdata(pdev);
usb_del_gadget_udc(&dum->gadget);
- platform_set_drvdata(pdev, NULL);
device_remove_file(&dum->gadget.dev, &dev_attr_function);
return 0;
}
}
for (i = 0; i < mod_data.num; i++) {
dum[i] = kzalloc(sizeof(struct dummy), GFP_KERNEL);
- if (!dum[i])
+ if (!dum[i]) {
+ retval = -ENOMEM;
goto err_add_pdata;
+ }
retval = platform_device_add_data(the_hcd_pdev[i], &dum[i],
sizeof(void *));
if (retval)
* @c: the configuration to support the network link
* @ethaddr: a buffer in which the ethernet address of the host side
* side of the link was recorded
+ * @dev: eth_dev structure
* Context: single threaded during gadget setup
*
* Returns zero on success, else negative errno.
* @c: the configuration to support the network link
* @ethaddr: a buffer in which the ethernet address of the host side
* side of the link was recorded
+ * @dev: eth_dev structure
* Context: single threaded during gadget setup
*
* Returns zero on success, else negative errno.
{
struct snd_card *card = platform_get_drvdata(pdev);
- platform_set_drvdata(pdev, NULL);
-
if (card)
return snd_card_free(card);
fusb300->ep0_req = fusb300_alloc_request(&fusb300->ep[0]->ep,
GFP_KERNEL);
- if (fusb300->ep0_req == NULL)
+ if (fusb300->ep0_req == NULL) {
+ ret = -ENOMEM;
goto clean_up3;
+ }
init_controller(fusb300);
ret = usb_add_gadget_udc(&pdev->dev, &fusb300->gadget);
if (pdata->exit)
pdata->exit(&pdev->dev);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
m66592->epaddr2ep[0] = &m66592->ep[0];
m66592->ep0_req = m66592_alloc_request(&m66592->ep[0].ep, GFP_KERNEL);
- if (m66592->ep0_req == NULL)
+ if (m66592->ep0_req == NULL) {
+ ret = -ENOMEM;
goto clean_up3;
+ }
m66592->ep0_req->complete = nop_completion;
init_controller(m66592);
dev->transceiver = NULL;
}
- platform_set_drvdata(pdev, NULL);
the_controller = NULL;
return 0;
}
r8a66597->ep0_req = r8a66597_alloc_request(&r8a66597->ep[0].ep,
GFP_KERNEL);
- if (r8a66597->ep0_req == NULL)
+ if (r8a66597->ep0_req == NULL) {
+ ret = -ENOMEM;
goto clean_up3;
+ }
r8a66597->ep0_req->complete = nop_completion;
ret = usb_add_gadget_udc(&pdev->dev, &r8a66597->gadget);
if (hs_req->req.length == 0)
return;
- usb_gadget_unmap_request(&hsotg->gadget, hs_req, hs_ep->dir_in);
+ usb_gadget_unmap_request(&hsotg->gadget, req, hs_ep->dir_in);
}
/**
irq = gpio_to_irq(udc_info->vbus_pin);
if (irq < 0) {
dev_err(dev, "no irq for gpio vbus pin\n");
+ retval = irq;
goto err_gpio_claim;
}
iounmap(base_addr);
release_mem_region(rsrc_start, rsrc_len);
- platform_set_drvdata(pdev, NULL);
-
if (!IS_ERR(udc_clock) && udc_clock != NULL) {
clk_disable(udc_clock);
clk_put(udc_clock);
ss_opts->bulk_buflen = gzero_options.bulk_buflen;
func_ss = usb_get_function(func_inst_ss);
- if (IS_ERR(func_ss))
+ if (IS_ERR(func_ss)) {
+ status = PTR_ERR(func_ss);
goto err_put_func_inst_ss;
+ }
func_inst_lb = usb_get_function_instance("Loopback");
- if (IS_ERR(func_inst_lb))
+ if (IS_ERR(func_inst_lb)) {
+ status = PTR_ERR(func_inst_lb);
goto err_put_func_ss;
+ }
lb_opts = container_of(func_inst_lb, struct f_lb_opts, func_inst);
lb_opts->bulk_buflen = gzero_options.bulk_buflen;
config USB_UHCI_HCD
tristate "UHCI HCD (most Intel and VIA) support"
- depends on PCI || SPARC_LEON || ARCH_VT8500
+ depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
---help---
The Universal Host Controller Interface is a standard by Intel for
accessing the USB hardware in the PC (which is also called the USB
config USB_UHCI_SUPPORT_NON_PCI_HC
bool
- depends on USB_UHCI_HCD
- default y if (SPARC_LEON || ARCH_VT8500)
+ default y if (SPARC_LEON || USB_UHCI_PLATFORM)
config USB_UHCI_PLATFORM
- bool "Generic UHCI Platform Driver support"
- depends on USB_UHCI_SUPPORT_NON_PCI_HC
+ bool
default y if ARCH_VT8500
- ---help---
- Enable support for generic UHCI platform devices that require no
- additional configuration.
config USB_UHCI_BIG_ENDIAN_MMIO
bool
- depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
- default y
+ default y if SPARC_LEON
config USB_UHCI_BIG_ENDIAN_DESC
bool
- depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
- default y
+ default y if SPARC_LEON
config USB_FHCI_HCD
tristate "Freescale QE USB Host Controller support"
/*-------------------------------------------------------------------------*/
-static u64 at91_ehci_dma_mask = DMA_BIT_MASK(32);
-
static int ehci_atmel_drv_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &at91_ehci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
if (!hcd) {
#define PLATFORM_DRIVER ehci_hcd_sead3_driver
#endif
-#if !IS_ENABLED(CONFIG_USB_EHCI_PCI) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_PLATFORM) && \
- !IS_ENABLED(CONFIG_USB_CHIPIDEA_HOST) && \
- !IS_ENABLED(CONFIG_USB_EHCI_MXC) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_OMAP) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_ORION) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_SPEAR) && \
- !IS_ENABLED(CONFIG_USB_EHCI_S5P) && \
- !IS_ENABLED(CONFIG_USB_EHCI_HCD_AT91) && \
- !IS_ENABLED(CONFIG_USB_EHCI_MSM) && \
- !defined(PLATFORM_DRIVER) && \
- !defined(PS3_SYSTEM_BUS_DRIVER) && \
- !defined(OF_PLATFORM_DRIVER) && \
- !defined(XILINX_OF_PLATFORM_DRIVER)
-#error "missing bus glue for ehci-hcd"
-#endif
-
static int __init ehci_hcd_init(void)
{
int retval = 0;
.extra_priv_size = sizeof(struct omap_hcd),
};
-static u64 omap_ehci_dma_mask = DMA_BIT_MASK(32);
-
/**
* ehci_hcd_omap_probe - initialize TI-based HCDs
*
* Since shared usb code relies on it, set it here for now.
* Once we have dma capability bindings this can go away.
*/
- if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &omap_ehci_dma_mask;
+ if (!dev->dma_mask)
+ dev->dma_mask = &dev->coherent_dma_mask;
+ if (!dev->coherent_dma_mask)
+ dev->coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(&ehci_omap_hc_driver, dev,
dev_name(dev));
}
}
-static u64 ehci_orion_dma_mask = DMA_BIT_MASK(32);
-
static int ehci_orion_drv_probe(struct platform_device *pdev)
{
struct orion_ehci_data *pd = pdev->dev.platform_data;
* now. Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &ehci_orion_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (!request_mem_region(res->start, resource_size(res),
ehci_orion_hc_driver.description)) {
dev_err(dev, "can't request ehci vbus gpio %d", gpio);
}
-static u64 ehci_s5p_dma_mask = DMA_BIT_MASK(32);
-
static int s5p_ehci_probe(struct platform_device *pdev)
{
struct s5p_ehci_platdata *pdata = pdev->dev.platform_data;
* Once we move to full device tree support this will vanish off.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &ehci_s5p_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
if (!pdev->dev.coherent_dma_mask)
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (IS_ERR(phy)) {
/* Fallback to pdata */
if (!pdata) {
+ usb_put_hcd(hcd);
dev_warn(&pdev->dev, "no platform data or transceiver defined\n");
return -EPROBE_DEFER;
} else {
static SIMPLE_DEV_PM_OPS(ehci_spear_pm_ops, ehci_spear_drv_suspend,
ehci_spear_drv_resume);
-static u64 spear_ehci_dma_mask = DMA_BIT_MASK(32);
-
static int spear_ehci_hcd_drv_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd ;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &spear_ehci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
usbh_clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(usbh_clk)) {
writel(val, base + TEGRA_USB_PORTSC1);
}
-static u64 tegra_ehci_dma_mask = DMA_BIT_MASK(32);
-
static int tegra_ehci_probe(struct platform_device *pdev)
{
struct resource *res;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &tegra_ehci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
setup_vbus_gpio(pdev, pdata);
int retval = 1;
unsigned long flags;
- /* if !USB_SUSPEND, root hub timers won't get shut down ... */
+ /* if !PM_RUNTIME, root hub timers won't get shut down ... */
if (!HC_IS_RUNNING(hcd->state))
return 0;
irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!irq_res) {
pr_warning("isp1760: IRQ resource not available\n");
- return -ENODEV;
+ ret = -ENODEV;
+ goto cleanup;
}
+
irqflags |= irq_res->flags & IRQF_TRIGGER_MASK;
if (priv) {
MODULE_DEVICE_TABLE(of, at91_ohci_dt_ids);
-static u64 at91_ohci_dma_mask = DMA_BIT_MASK(32);
-
static int ohci_at91_of_init(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &at91_ohci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
.start_port_reset = ohci_start_port_reset,
};
-static u64 ohci_exynos_dma_mask = DMA_BIT_MASK(32);
-
static int exynos_ohci_probe(struct platform_device *pdev)
{
struct exynos4_ohci_platdata *pdata = pdev->dev.platform_data;
* Once we move to full device tree support this will vanish off.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &ohci_exynos_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
if (!pdev->dev.coherent_dma_mask)
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
urb->start_frame = frame;
}
} else if (ed->type == PIPE_ISOCHRONOUS) {
- u16 next = ohci_frame_no(ohci) + 2;
+ u16 next = ohci_frame_no(ohci) + 1;
u16 frame = ed->last_iso + ed->interval;
/* Behind the scheduling threshold? */
if (unlikely(tick_before(frame, next))) {
/* USB_ISO_ASAP: Round up to the first available slot */
- if (urb->transfer_flags & URB_ISO_ASAP)
+ if (urb->transfer_flags & URB_ISO_ASAP) {
frame += (next - frame + ed->interval - 1) &
-ed->interval;
* Not ASAP: Use the next slot in the stream. If
* the entire URB falls before the threshold, fail.
*/
- else if (tick_before(frame + ed->interval *
+ } else {
+ if (tick_before(frame + ed->interval *
(urb->number_of_packets - 1), next)) {
- retval = -EXDEV;
- usb_hcd_unlink_urb_from_ep(hcd, urb);
- goto fail;
- }
+ retval = -EXDEV;
+ usb_hcd_unlink_urb_from_ep(hcd, urb);
+ goto fail;
+ }
- /*
- * Some OHCI hardware doesn't handle late TDs
- * correctly. After retiring them it proceeds to
- * the next ED instead of the next TD. Therefore
- * we have to omit the late TDs entirely.
- */
- urb_priv->td_cnt = DIV_ROUND_UP(next - frame,
- ed->interval);
+ /*
+ * Some OHCI hardware doesn't handle late TDs
+ * correctly. After retiring them it proceeds
+ * to the next ED instead of the next TD.
+ * Therefore we have to omit the late TDs
+ * entirely.
+ */
+ urb_priv->td_cnt = DIV_ROUND_UP(
+ (u16) (next - frame),
+ ed->interval);
+ }
}
urb->start_frame = frame;
}
isp1301_i2c_client = isp1301_get_client(isp1301_node);
if (!isp1301_i2c_client) {
- ret = -EPROBE_DEFER;
- goto out;
+ return -EPROBE_DEFER;
}
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
if (usb_disabled()) {
dev_err(&pdev->dev, "USB is disabled\n");
ret = -ENODEV;
- goto out;
+ goto fail_disable;
}
/* Enable AHB slave USB clock, needed for further USB clock control */
if (IS_ERR(usb_pll_clk)) {
dev_err(&pdev->dev, "failed to acquire USB PLL\n");
ret = PTR_ERR(usb_pll_clk);
- goto out1;
+ goto fail_pll;
}
ret = clk_enable(usb_pll_clk);
if (ret < 0) {
dev_err(&pdev->dev, "failed to start USB PLL\n");
- goto out2;
+ goto fail_pllen;
}
ret = clk_set_rate(usb_pll_clk, 48000);
if (ret < 0) {
dev_err(&pdev->dev, "failed to set USB clock rate\n");
- goto out3;
+ goto fail_rate;
}
/* Enable USB device clock */
if (IS_ERR(usb_dev_clk)) {
dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n");
ret = PTR_ERR(usb_dev_clk);
- goto out4;
+ goto fail_dev;
}
ret = clk_enable(usb_dev_clk);
if (ret < 0) {
dev_err(&pdev->dev, "failed to start USB DEV Clock\n");
- goto out5;
+ goto fail_deven;
}
/* Enable USB otg clocks */
if (IS_ERR(usb_otg_clk)) {
dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n");
ret = PTR_ERR(usb_otg_clk);
- goto out6;
+ goto fail_otg;
}
__raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL);
ret = clk_enable(usb_otg_clk);
if (ret < 0) {
dev_err(&pdev->dev, "failed to start USB DEV Clock\n");
- goto out7;
+ goto fail_otgen;
}
isp1301_configure();
if (!hcd) {
dev_err(&pdev->dev, "Failed to allocate HC buffer\n");
ret = -ENOMEM;
- goto out8;
+ goto fail_hcd;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
hcd->regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(hcd->regs)) {
ret = PTR_ERR(hcd->regs);
- goto out8;
+ goto fail_resource;
}
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
ret = -ENXIO;
- goto out8;
+ goto fail_resource;
}
nxp_start_hc();
return ret;
nxp_stop_hc();
-out8:
+fail_resource:
usb_put_hcd(hcd);
-out7:
+fail_hcd:
clk_disable(usb_otg_clk);
-out6:
+fail_otgen:
clk_put(usb_otg_clk);
-out5:
+fail_otg:
clk_disable(usb_dev_clk);
-out4:
+fail_deven:
clk_put(usb_dev_clk);
-out3:
+fail_dev:
+fail_rate:
clk_disable(usb_pll_clk);
-out2:
+fail_pllen:
clk_put(usb_pll_clk);
-out1:
+fail_pll:
+fail_disable:
isp1301_i2c_client = NULL;
-out:
return ret;
}
/*-------------------------------------------------------------------------*/
-static u64 omap_ohci_dma_mask = DMA_BIT_MASK(32);
-
/*
* configure so an HC device and id are always provided
* always called with process context; sleeping is OK
* Since shared usb code relies on it, set it here for now.
* Once we have dma capability bindings this can go away.
*/
- if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &omap_ohci_dma_mask;
+ if (!dev->dma_mask)
+ dev->dma_mask = &dev->coherent_dma_mask;
+ if (!dev->coherent_dma_mask)
+ dev->coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(&ohci_omap3_hc_driver, dev,
dev_name(dev));
MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);
-static u64 pxa_ohci_dma_mask = DMA_BIT_MASK(32);
-
static int ohci_pxa_of_init(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &pxa_ohci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
.start_port_reset = ohci_start_port_reset,
};
-static u64 spear_ohci_dma_mask = DMA_BIT_MASK(32);
-
static int spear_ohci_hcd_drv_probe(struct platform_device *pdev)
{
const struct hc_driver *driver = &ohci_spear_hc_driver;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &spear_ohci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
usbh_clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(usbh_clk)) {
int ports, i, retval = 1;
unsigned long flags;
- /* if !USB_SUSPEND, root hub timers won't get shut down ... */
+ /* if !PM_RUNTIME, root hub timers won't get shut down ... */
if (!HC_IS_RUNNING(hcd->state))
return 0;
* and usb-storage.
*
* TODO:
- * - usb suspend/resume triggered by sl811 (with USB_SUSPEND)
+ * - usb suspend/resume triggered by sl811 (with PM_RUNTIME)
* - various issues noted in the code
* - performance work; use both register banks; ...
* - use urb->iso_frame_desc[] with ISO transfers
/* auto-stop if nothing connected for 1 second */
if (any_ports_active(uhci))
uhci->rh_state = UHCI_RH_RUNNING;
- else if (time_after_eq(jiffies, uhci->auto_stop_time))
+ else if (time_after_eq(jiffies, uhci->auto_stop_time) &&
+ !uhci->wait_for_hp)
suspend_rh(uhci, UHCI_RH_AUTO_STOPPED);
break;
.hub_control = uhci_hub_control,
};
-static u64 platform_uhci_dma_mask = DMA_BIT_MASK(32);
-
static int uhci_hcd_platform_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd;
* Once we have dma capability bindings this can go away.
*/
if (!pdev->dev.dma_mask)
- pdev->dev.dma_mask = &platform_uhci_dma_mask;
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ if (!pdev->dev.coherent_dma_mask)
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
hcd = usb_create_hcd(&uhci_platform_hc_driver, &pdev->dev,
pdev->name);
return -EINVAL; /* Can't change the period */
} else {
- next = uhci->frame_number + 2;
+ next = uhci->frame_number + 1;
/* Find the next unused frame */
if (list_empty(&qh->queue)) {
ep_ctx->ep_info2 |= cpu_to_le32(xhci_get_endpoint_type(udev, ep));
/* Set the max packet size and max burst */
+ max_packet = GET_MAX_PACKET(usb_endpoint_maxp(&ep->desc));
+ max_burst = 0;
switch (udev->speed) {
case USB_SPEED_SUPER:
- max_packet = usb_endpoint_maxp(&ep->desc);
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet));
/* dig out max burst from ep companion desc */
- max_packet = ep->ss_ep_comp.bMaxBurst;
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_BURST(max_packet));
+ max_burst = ep->ss_ep_comp.bMaxBurst;
break;
case USB_SPEED_HIGH:
+ /* Some devices get this wrong */
+ if (usb_endpoint_xfer_bulk(&ep->desc))
+ max_packet = 512;
/* bits 11:12 specify the number of additional transaction
* opportunities per microframe (USB 2.0, section 9.6.6)
*/
usb_endpoint_xfer_int(&ep->desc)) {
max_burst = (usb_endpoint_maxp(&ep->desc)
& 0x1800) >> 11;
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_BURST(max_burst));
}
- /* Fall through */
+ break;
case USB_SPEED_FULL:
case USB_SPEED_LOW:
- max_packet = GET_MAX_PACKET(usb_endpoint_maxp(&ep->desc));
- ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet));
break;
default:
BUG();
}
+ ep_ctx->ep_info2 |= cpu_to_le32(MAX_PACKET(max_packet) |
+ MAX_BURST(max_burst));
max_esit_payload = xhci_get_max_esit_payload(xhci, udev, ep);
ep_ctx->tx_info = cpu_to_le32(MAX_ESIT_PAYLOAD_FOR_EP(max_esit_payload));
if (!config) {
dev_err(&pdev->dev,
"failed to allocate musb hdrc config\n");
+ ret = -ENOMEM;
goto err2;
}
glue->control_otghs = omap_get_control_dev();
if (IS_ERR(glue->control_otghs)) {
dev_vdbg(&pdev->dev, "Failed to get control device\n");
- return -ENODEV;
+ ret = PTR_ERR(glue->control_otghs);
+ goto err2;
}
} else {
glue->control_otghs = ERR_PTR(-ENODEV);
config FSL_USB2_OTG
bool "Freescale USB OTG Transceiver Driver"
- depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
+ depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
select USB_OTG
help
Enable this to support Freescale USB OTG transceiver.
tristate "NXP ISP1301 USB transceiver support"
depends on USB || USB_GADGET
depends on I2C
- select USB_OTG_UTILS
help
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
This chip is typically used as USB transceiver for USB host, gadget
config USB_MV_OTG
tristate "Marvell USB OTG support"
- depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
+ depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
select USB_OTG
help
Say Y here if you want to build Marvell USB OTG transciever
else if (ab->mode == USB_PERIPHERAL)
ab8500_usb_peri_phy_dis(ab);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
/* initialize the otg structure */
fsl_otg_tc->phy.label = DRIVER_DESC;
+ fsl_otg_tc->phy.dev = &pdev->dev;
fsl_otg_tc->phy.set_power = fsl_otg_set_power;
fsl_otg_tc->phy.otg->phy = &fsl_otg_tc->phy;
platform_set_drvdata(pdev, gpio_vbus);
gpio_vbus->dev = &pdev->dev;
gpio_vbus->phy.label = "gpio-vbus";
+ gpio_vbus->phy.dev = gpio_vbus->dev;
gpio_vbus->phy.set_power = gpio_vbus_set_power;
gpio_vbus->phy.set_suspend = gpio_vbus_set_suspend;
gpio_vbus->phy.state = OTG_STATE_UNDEFINED;
gpio_free(pdata->gpio_pullup);
gpio_free(pdata->gpio_vbus);
err_gpio:
- platform_set_drvdata(pdev, NULL);
kfree(gpio_vbus->phy.otg);
kfree(gpio_vbus);
return err;
if (gpio_is_valid(pdata->gpio_pullup))
gpio_free(pdata->gpio_pullup);
gpio_free(gpio);
- platform_set_drvdata(pdev, NULL);
kfree(gpio_vbus->phy.otg);
kfree(gpio_vbus);
mutex_init(&isp->mutex);
phy = &isp->phy;
+ phy->dev = &client->dev;
phy->label = DRV_NAME;
phy->init = isp1301_phy_init;
phy->set_vbus = isp1301_phy_set_vbus;
mv_otg_disable(mvotg);
usb_remove_phy(&mvotg->phy);
- platform_set_drvdata(pdev, NULL);
return 0;
}
flush_workqueue(mvotg->qwork);
destroy_workqueue(mvotg->qwork);
- platform_set_drvdata(pdev, NULL);
-
return retval;
}
mxs_phy->phy.set_suspend = mxs_phy_suspend;
mxs_phy->phy.notify_connect = mxs_phy_on_connect;
mxs_phy->phy.notify_disconnect = mxs_phy_on_disconnect;
+ mxs_phy->phy.type = USB_PHY_TYPE_USB2;
ATOMIC_INIT_NOTIFIER_HEAD(&mxs_phy->phy.notifier);
usb_remove_phy(&mxs_phy->phy);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
usb_remove_phy(&nop->phy);
- platform_set_drvdata(pdev, NULL);
-
return 0;
}
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_OPENDCC_GBM_BOOST_PID) },
{ USB_DEVICE(NEWPORT_VID, NEWPORT_AGILIS_PID) },
+ { USB_DEVICE(NEWPORT_VID, NEWPORT_CONEX_CC_PID) },
+ { USB_DEVICE(NEWPORT_VID, NEWPORT_CONEX_AGP_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_IOBOARD_PID) },
{ USB_DEVICE(INTERBIOMETRICS_VID, INTERBIOMETRICS_MINI_IOBOARD_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_SPROG_II) },
static int ftdi_ioctl(struct tty_struct *tty,
unsigned int cmd, unsigned long arg);
static void ftdi_break_ctl(struct tty_struct *tty, int break_state);
-static int ftdi_chars_in_buffer(struct tty_struct *tty);
-static int ftdi_get_modem_status(struct tty_struct *tty,
+static bool ftdi_tx_empty(struct usb_serial_port *port);
+static int ftdi_get_modem_status(struct usb_serial_port *port,
unsigned char status[2]);
static unsigned short int ftdi_232am_baud_base_to_divisor(int baud, int base);
.ioctl = ftdi_ioctl,
.set_termios = ftdi_set_termios,
.break_ctl = ftdi_break_ctl,
- .chars_in_buffer = ftdi_chars_in_buffer,
+ .tx_empty = ftdi_tx_empty,
};
static struct usb_serial_driver * const serial_drivers[] = {
}
-static int ftdi_chars_in_buffer(struct tty_struct *tty)
+static bool ftdi_tx_empty(struct usb_serial_port *port)
{
- struct usb_serial_port *port = tty->driver_data;
- int chars;
unsigned char buf[2];
int ret;
- chars = usb_serial_generic_chars_in_buffer(tty);
- if (chars)
- goto out;
-
- /* Check if hardware buffer is empty. */
- ret = ftdi_get_modem_status(tty, buf);
+ ret = ftdi_get_modem_status(port, buf);
if (ret == 2) {
if (!(buf[1] & FTDI_RS_TEMT))
- chars = 1;
+ return false;
}
-out:
- dev_dbg(&port->dev, "%s - %d\n", __func__, chars);
- return chars;
+ return true;
}
/* old_termios contains the original termios settings and tty->termios contains
* Returns the number of status bytes retrieved (device dependant), or
* negative error code.
*/
-static int ftdi_get_modem_status(struct tty_struct *tty,
+static int ftdi_get_modem_status(struct usb_serial_port *port,
unsigned char status[2])
{
- struct usb_serial_port *port = tty->driver_data;
struct ftdi_private *priv = usb_get_serial_port_data(port);
unsigned char *buf;
int len;
unsigned char buf[2];
int ret;
- ret = ftdi_get_modem_status(tty, buf);
+ ret = ftdi_get_modem_status(port, buf);
if (ret < 0)
return ret;
*/
#define NEWPORT_VID 0x104D
#define NEWPORT_AGILIS_PID 0x3000
+#define NEWPORT_CONEX_CC_PID 0x3002
+#define NEWPORT_CONEX_AGP_PID 0x3006
/* Interbiometrics USB I/O Board */
/* Developed for Interbiometrics by Rudolf Gugler */
}
EXPORT_SYMBOL_GPL(usb_serial_generic_chars_in_buffer);
+void usb_serial_generic_wait_until_sent(struct tty_struct *tty, long timeout)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ unsigned int bps;
+ unsigned long period;
+ unsigned long expire;
+
+ bps = tty_get_baud_rate(tty);
+ if (!bps)
+ bps = 9600; /* B0 */
+ /*
+ * Use a poll-period of roughly the time it takes to send one
+ * character or at least one jiffy.
+ */
+ period = max_t(unsigned long, (10 * HZ / bps), 1);
+ period = min_t(unsigned long, period, timeout);
+
+ dev_dbg(&port->dev, "%s - timeout = %u ms, period = %u ms\n",
+ __func__, jiffies_to_msecs(timeout),
+ jiffies_to_msecs(period));
+ expire = jiffies + timeout;
+ while (!port->serial->type->tx_empty(port)) {
+ schedule_timeout_interruptible(period);
+ if (signal_pending(current))
+ break;
+ if (time_after(jiffies, expire))
+ break;
+ }
+}
+EXPORT_SYMBOL_GPL(usb_serial_generic_wait_until_sent);
+
static int usb_serial_generic_submit_read_urb(struct usb_serial_port *port,
int index, gfp_t mem_flags)
{
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int chars = 0;
unsigned long flags;
- int ret;
-
if (edge_port == NULL)
return 0;
chars = kfifo_len(&edge_port->write_fifo);
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
- if (!chars) {
- ret = tx_active(edge_port);
- if (ret > 0)
- chars = ret;
- }
-
dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
return chars;
}
+static bool edge_tx_empty(struct usb_serial_port *port)
+{
+ struct edgeport_port *edge_port = usb_get_serial_port_data(port);
+ int ret;
+
+ ret = tx_active(edge_port);
+ if (ret > 0)
+ return false;
+
+ return true;
+}
+
static void edge_throttle(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
.write = edge_write,
.write_room = edge_write_room,
.chars_in_buffer = edge_chars_in_buffer,
+ .tx_empty = edge_tx_empty,
.break_ctl = edge_break,
.read_int_callback = edge_interrupt_callback,
.read_bulk_callback = edge_bulk_in_callback,
.write = edge_write,
.write_room = edge_write_room,
.chars_in_buffer = edge_chars_in_buffer,
+ .tx_empty = edge_tx_empty,
.break_ctl = edge_break,
.read_int_callback = edge_interrupt_callback,
.read_bulk_callback = edge_bulk_in_callback,
#define DELL_PRODUCT_5800_MINICARD_VZW 0x8195 /* Novatel E362 */
#define DELL_PRODUCT_5800_V2_MINICARD_VZW 0x8196 /* Novatel E362 */
+#define DELL_PRODUCT_5804_MINICARD_ATT 0x819b /* Novatel E371 */
#define KYOCERA_VENDOR_ID 0x0c88
#define KYOCERA_PRODUCT_KPC650 0x17da
#define CINTERION_PRODUCT_EU3_E 0x0051
#define CINTERION_PRODUCT_EU3_P 0x0052
#define CINTERION_PRODUCT_PH8 0x0053
-#define CINTERION_PRODUCT_AH6 0x0055
-#define CINTERION_PRODUCT_PLS8 0x0060
+#define CINTERION_PRODUCT_AHXX 0x0055
+#define CINTERION_PRODUCT_PLXX 0x0060
/* Olivetti products */
#define OLIVETTI_VENDOR_ID 0x0b3c
{ USB_DEVICE(DELL_VENDOR_ID, DELL_PRODUCT_5730_MINICARD_VZW) }, /* Dell Wireless 5730 Mobile Broadband EVDO/HSPA Mini-Card */
{ USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5800_MINICARD_VZW, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5800_V2_MINICARD_VZW, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(DELL_VENDOR_ID, DELL_PRODUCT_5804_MINICARD_ATT, 0xff, 0xff, 0xff) },
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_E100A) }, /* ADU-E100, ADU-310 */
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) },
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) },
.driver_info = (kernel_ulong_t)&net_intf4_blacklist },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0330, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0395, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0412, 0xff, 0xff, 0xff), /* Telewell TW-LTE 4G */
+ .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0414, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0417, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1008, 0xff, 0xff, 0xff),
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_E) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_P) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PH8) },
- { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_AH6) },
- { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PLS8) },
+ { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_AHXX) },
+ { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PLXX),
+ .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) },
{ USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) },
{ USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDM) },
const unsigned char *data, int count);
static int ti_write_room(struct tty_struct *tty);
static int ti_chars_in_buffer(struct tty_struct *tty);
+static bool ti_tx_empty(struct usb_serial_port *port);
static void ti_throttle(struct tty_struct *tty);
static void ti_unthrottle(struct tty_struct *tty);
static int ti_ioctl(struct tty_struct *tty,
.write = ti_write,
.write_room = ti_write_room,
.chars_in_buffer = ti_chars_in_buffer,
+ .tx_empty = ti_tx_empty,
.throttle = ti_throttle,
.unthrottle = ti_unthrottle,
.ioctl = ti_ioctl,
.write = ti_write,
.write_room = ti_write_room,
.chars_in_buffer = ti_chars_in_buffer,
+ .tx_empty = ti_tx_empty,
.throttle = ti_throttle,
.unthrottle = ti_unthrottle,
.ioctl = ti_ioctl,
struct ti_port *tport = usb_get_serial_port_data(port);
int chars = 0;
unsigned long flags;
- int ret;
- u8 lsr;
if (tport == NULL)
return 0;
chars = kfifo_len(&tport->write_fifo);
spin_unlock_irqrestore(&tport->tp_lock, flags);
- if (!chars) {
- ret = ti_get_lsr(tport, &lsr);
- if (!ret && !(lsr & TI_LSR_TX_EMPTY))
- chars = 1;
- }
-
dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
return chars;
}
+static bool ti_tx_empty(struct usb_serial_port *port)
+{
+ struct ti_port *tport = usb_get_serial_port_data(port);
+ int ret;
+ u8 lsr;
+
+ ret = ti_get_lsr(tport, &lsr);
+ if (!ret && !(lsr & TI_LSR_TX_EMPTY))
+ return false;
+
+ return true;
+}
static void ti_throttle(struct tty_struct *tty)
{
{
struct usb_serial_port *port = tty->driver_data;
struct usb_serial *serial = port->serial;
- int count = 0;
dev_dbg(tty->dev, "%s\n", __func__);
- mutex_lock(&serial->disc_mutex);
- /* if the device was unplugged then any remaining characters
- fell out of the connector ;) */
if (serial->disconnected)
- count = 0;
- else
- count = serial->type->chars_in_buffer(tty);
- mutex_unlock(&serial->disc_mutex);
+ return 0;
+
+ return serial->type->chars_in_buffer(tty);
+}
+
+static void serial_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+ struct usb_serial_port *port = tty->driver_data;
+ struct usb_serial *serial = port->serial;
+
+ dev_dbg(tty->dev, "%s\n", __func__);
+
+ if (!port->serial->type->wait_until_sent)
+ return;
- return count;
+ mutex_lock(&serial->disc_mutex);
+ if (!serial->disconnected)
+ port->serial->type->wait_until_sent(tty, timeout);
+ mutex_unlock(&serial->disc_mutex);
}
static void serial_throttle(struct tty_struct *tty)
.unthrottle = serial_unthrottle,
.break_ctl = serial_break,
.chars_in_buffer = serial_chars_in_buffer,
+ .wait_until_sent = serial_wait_until_sent,
.tiocmget = serial_tiocmget,
.tiocmset = serial_tiocmset,
.get_icount = serial_get_icount,
set_to_generic_if_null(device, close);
set_to_generic_if_null(device, write_room);
set_to_generic_if_null(device, chars_in_buffer);
+ if (device->tx_empty)
+ set_to_generic_if_null(device, wait_until_sent);
set_to_generic_if_null(device, read_bulk_callback);
set_to_generic_if_null(device, write_bulk_callback);
set_to_generic_if_null(device, process_read_urb);
int status_len;
u32 flag;
-#ifdef CONFIG_REALTEK_AUTOPM
struct us_data *us;
+
+#ifdef CONFIG_REALTEK_AUTOPM
struct timer_list rts51x_suspend_timer;
unsigned long timer_expires;
int pwr_state;
us->extra = chip;
us->extra_destructor = realtek_cr_destructor;
us->max_lun = chip->max_lun = rts51x_get_max_lun(us);
+ chip->us = us;
usb_stor_dbg(us, "chip->max_lun = %d\n", chip->max_lun);
SET_AUTO_DELINK(chip);
}
#ifdef CONFIG_REALTEK_AUTOPM
- if (ss_en) {
- chip->us = us;
+ if (ss_en)
realtek_cr_autosuspend_setup(us);
- }
#endif
usb_stor_dbg(us, "chip->flag = 0x%x\n", chip->flag);
config FB_GOLDFISH
tristate "Goldfish Framebuffer"
- depends on FB
+ depends on FB && HAS_DMA
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
help
This framebuffer driver supports Microsoft Hyper-V Synthetic Video.
+config FB_SIMPLE
+ bool "Simple framebuffer support"
+ depends on (FB = y) && OF
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ help
+ Say Y if you want support for a simple frame-buffer.
+
+ This driver assumes that the display hardware has been initialized
+ before the kernel boots, and the kernel will simply render to the
+ pre-allocated frame buffer surface.
+
+ Configuration re: surface address, size, and format must be provided
+ through device tree, or potentially plain old platform data in the
+ future.
+
source "drivers/video/omap/Kconfig"
source "drivers/video/omap2/Kconfig"
source "drivers/video/exynos/Kconfig"
obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o
obj-$(CONFIG_FB_MXS) += mxsfb.o
obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o
+obj-$(CONFIG_FB_SIMPLE) += simplefb.o
# the test framebuffer is last
obj-$(CONFIG_FB_VIRTUAL) += vfb.o
font-objs += $(font-objs-y)
+obj-$(CONFIG_FONTS) += font.o
+
# Each configuration option enables a list of files.
obj-$(CONFIG_DUMMY_CONSOLE) += dummycon.o
--- /dev/null
+/*
+ * Simplest possible simple frame-buffer driver, as a platform device
+ *
+ * Copyright (c) 2013, Stephen Warren
+ *
+ * Based on q40fb.c, which was:
+ * Copyright (C) 2001 Richard Zidlicky <rz@linux-m68k.org>
+ *
+ * Also based on offb.c, which was:
+ * Copyright (C) 1997 Geert Uytterhoeven
+ * Copyright (C) 1996 Paul Mackerras
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/errno.h>
+#include <linux/fb.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+static struct fb_fix_screeninfo simplefb_fix = {
+ .id = "simple",
+ .type = FB_TYPE_PACKED_PIXELS,
+ .visual = FB_VISUAL_TRUECOLOR,
+ .accel = FB_ACCEL_NONE,
+};
+
+static struct fb_var_screeninfo simplefb_var = {
+ .height = -1,
+ .width = -1,
+ .activate = FB_ACTIVATE_NOW,
+ .vmode = FB_VMODE_NONINTERLACED,
+};
+
+static int simplefb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int transp, struct fb_info *info)
+{
+ u32 *pal = info->pseudo_palette;
+ u32 cr = red >> (16 - info->var.red.length);
+ u32 cg = green >> (16 - info->var.green.length);
+ u32 cb = blue >> (16 - info->var.blue.length);
+ u32 value;
+
+ if (regno >= 16)
+ return -EINVAL;
+
+ value = (cr << info->var.red.offset) |
+ (cg << info->var.green.offset) |
+ (cb << info->var.blue.offset);
+ if (info->var.transp.length > 0) {
+ u32 mask = (1 << info->var.transp.length) - 1;
+ mask <<= info->var.transp.offset;
+ value |= mask;
+ }
+ pal[regno] = value;
+
+ return 0;
+}
+
+static struct fb_ops simplefb_ops = {
+ .owner = THIS_MODULE,
+ .fb_setcolreg = simplefb_setcolreg,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+};
+
+struct simplefb_format {
+ const char *name;
+ u32 bits_per_pixel;
+ struct fb_bitfield red;
+ struct fb_bitfield green;
+ struct fb_bitfield blue;
+ struct fb_bitfield transp;
+};
+
+static struct simplefb_format simplefb_formats[] = {
+ { "r5g6b5", 16, {11, 5}, {5, 6}, {0, 5}, {0, 0} },
+};
+
+struct simplefb_params {
+ u32 width;
+ u32 height;
+ u32 stride;
+ struct simplefb_format *format;
+};
+
+static int simplefb_parse_dt(struct platform_device *pdev,
+ struct simplefb_params *params)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+ const char *format;
+ int i;
+
+ ret = of_property_read_u32(np, "width", ¶ms->width);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse width property\n");
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "height", ¶ms->height);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse height property\n");
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "stride", ¶ms->stride);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse stride property\n");
+ return ret;
+ }
+
+ ret = of_property_read_string(np, "format", &format);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't parse format property\n");
+ return ret;
+ }
+ params->format = NULL;
+ for (i = 0; i < ARRAY_SIZE(simplefb_formats); i++) {
+ if (strcmp(format, simplefb_formats[i].name))
+ continue;
+ params->format = &simplefb_formats[i];
+ break;
+ }
+ if (!params->format) {
+ dev_err(&pdev->dev, "Invalid format value\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int simplefb_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct simplefb_params params;
+ struct fb_info *info;
+ struct resource *mem;
+
+ if (fb_get_options("simplefb", NULL))
+ return -ENODEV;
+
+ ret = simplefb_parse_dt(pdev, ¶ms);
+ if (ret)
+ return ret;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(&pdev->dev, "No memory resource\n");
+ return -EINVAL;
+ }
+
+ info = framebuffer_alloc(sizeof(u32) * 16, &pdev->dev);
+ if (!info)
+ return -ENOMEM;
+ platform_set_drvdata(pdev, info);
+
+ info->fix = simplefb_fix;
+ info->fix.smem_start = mem->start;
+ info->fix.smem_len = resource_size(mem);
+ info->fix.line_length = params.stride;
+
+ info->var = simplefb_var;
+ info->var.xres = params.width;
+ info->var.yres = params.height;
+ info->var.xres_virtual = params.width;
+ info->var.yres_virtual = params.height;
+ info->var.bits_per_pixel = params.format->bits_per_pixel;
+ info->var.red = params.format->red;
+ info->var.green = params.format->green;
+ info->var.blue = params.format->blue;
+ info->var.transp = params.format->transp;
+
+ info->fbops = &simplefb_ops;
+ info->flags = FBINFO_DEFAULT;
+ info->screen_base = devm_ioremap(&pdev->dev, info->fix.smem_start,
+ info->fix.smem_len);
+ if (!info->screen_base) {
+ framebuffer_release(info);
+ return -ENODEV;
+ }
+ info->pseudo_palette = (void *)(info + 1);
+
+ ret = register_framebuffer(info);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Unable to register simplefb: %d\n", ret);
+ framebuffer_release(info);
+ return ret;
+ }
+
+ dev_info(&pdev->dev, "fb%d: simplefb registered!\n", info->node);
+
+ return 0;
+}
+
+static int simplefb_remove(struct platform_device *pdev)
+{
+ struct fb_info *info = platform_get_drvdata(pdev);
+
+ unregister_framebuffer(info);
+ framebuffer_release(info);
+
+ return 0;
+}
+
+static const struct of_device_id simplefb_of_match[] = {
+ { .compatible = "simple-framebuffer", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, simplefb_of_match);
+
+static struct platform_driver simplefb_driver = {
+ .driver = {
+ .name = "simple-framebuffer",
+ .owner = THIS_MODULE,
+ .of_match_table = simplefb_of_match,
+ },
+ .probe = simplefb_probe,
+ .remove = simplefb_remove,
+};
+module_platform_driver(simplefb_driver);
+
+MODULE_AUTHOR("Stephen Warren <swarren@wwwdotorg.org>");
+MODULE_DESCRIPTION("Simple framebuffer driver");
+MODULE_LICENSE("GPL v2");
kunmap_atomic(ring);
while (atomic_read(&ctx->reqs_active) > 0) {
- wait_event(ctx->wait, head != ctx->tail);
+ wait_event(ctx->wait,
+ head != ctx->tail ||
+ atomic_read(&ctx->reqs_active) <= 0);
avail = (head <= ctx->tail ? ctx->tail : ctx->nr_events) - head;
* < min_nr if the timeout specified by timeout has elapsed
* before sufficient events are available, where timeout == NULL
* specifies an infinite timeout. Note that the timeout pointed to by
- * timeout is relative and will be updated if not NULL and the
- * operation blocks. Will fail with -ENOSYS if not implemented.
+ * timeout is relative. Will fail with -ENOSYS if not implemented.
*/
SYSCALL_DEFINE5(io_getevents, aio_context_t, ctx_id,
long, min_nr,
if (fattr->cf_flags & CIFS_FATTR_DFS_REFERRAL)
inode->i_flags |= S_AUTOMOUNT;
- cifs_set_ops(inode);
+ if (inode->i_state & I_NEW)
+ cifs_set_ops(inode);
}
void
return 0;
}
+static unsigned long calc_fat_clusters(struct super_block *sb)
+{
+ struct msdos_sb_info *sbi = MSDOS_SB(sb);
+
+ /* Divide first to avoid overflow */
+ if (sbi->fat_bits != 12) {
+ unsigned long ent_per_sec = sb->s_blocksize * 8 / sbi->fat_bits;
+ return ent_per_sec * sbi->fat_length;
+ }
+
+ return sbi->fat_length * sb->s_blocksize * 8 / sbi->fat_bits;
+}
+
/*
* Read the super block of an MS-DOS FS.
*/
sbi->dirty = b->fat16.state & FAT_STATE_DIRTY;
/* check that FAT table does not overflow */
- fat_clusters = sbi->fat_length * sb->s_blocksize * 8 / sbi->fat_bits;
+ fat_clusters = calc_fat_clusters(sb);
total_clusters = min(total_clusters, fat_clusters - FAT_START_ENT);
if (total_clusters > MAX_FAT(sb)) {
if (!silent)
config GFS2_FS_LOCKING_DLM
bool "GFS2 DLM locking"
depends on (GFS2_FS!=n) && NET && INET && (IPV6 || IPV6=n) && \
- HOTPLUG && DLM && CONFIGFS_FS && SYSFS
+ HOTPLUG && CONFIGFS_FS && SYSFS && (DLM=y || DLM=GFS2_FS)
help
Multiple node locking module for GFS2
fs_err(sdp, "Error %d writing to log\n", error);
}
- bio_for_each_segment(bvec, bio, i) {
+ bio_for_each_segment_all(bvec, bio, i) {
page = bvec->bv_page;
if (page_has_buffers(page))
gfs2_end_log_write_bh(sdp, bvec, error);
{
struct kqid qid = qd->qd_id;
return (2 * (u64)from_kqid(&init_user_ns, qid)) +
- (qid.type == USRQUOTA) ? 0 : 1;
+ ((qid.type == USRQUOTA) ? 0 : 1);
}
static u64 qd2offset(struct gfs2_quota_data *qd)
goto unlock_out;
}
- gfs2_trans_add_meta(ip->i_gl, bh);
+ gfs2_trans_add_data(ip->i_gl, bh);
kaddr = kmap_atomic(page);
if (offset + sizeof(struct gfs2_quota) > PAGE_CACHE_SIZE)
u32 extlen;
u32 free_blocks = rgd->rd_free_clone - rgd->rd_reserved;
int ret;
+ struct inode *inode = &ip->i_inode;
- extlen = max_t(u32, atomic_read(&rs->rs_sizehint), requested);
- extlen = clamp(extlen, RGRP_RSRV_MINBLKS, free_blocks);
+ if (S_ISDIR(inode->i_mode))
+ extlen = 1;
+ else {
+ extlen = max_t(u32, atomic_read(&rs->rs_sizehint), requested);
+ extlen = clamp(extlen, RGRP_RSRV_MINBLKS, free_blocks);
+ }
if ((rgd->rd_free_clone < rgd->rd_reserved) || (free_blocks < extlen))
return;
spin_lock(&tree->hash_lock);
node = hfs_bnode_findhash(tree, num);
spin_unlock(&tree->hash_lock);
- BUG_ON(node);
+ if (node) {
+ pr_crit("new node %u already hashed?\n", num);
+ WARN_ON(1);
+ return node;
+ }
node = __hfs_bnode_create(tree, num);
if (!node)
return ERR_PTR(-ENOMEM);
spin_lock(&tbl->slot_tbl_lock);
/* state manager is resetting the session */
- if (test_bit(NFS4_SESSION_DRAINING, &clp->cl_session->session_state)) {
+ if (test_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state)) {
spin_unlock(&tbl->slot_tbl_lock);
status = htonl(NFS4ERR_DELAY);
/* Return NFS4ERR_BADSESSION if we're draining the session
* A single slot, so highest used slotid is either 0 or -1
*/
tbl->highest_used_slotid = NFS4_NO_SLOT;
- nfs4_session_drain_complete(session, tbl);
+ nfs4_slot_tbl_drain_complete(tbl);
spin_unlock(&tbl->slot_tbl_lock);
}
__set_bit(NFS_CS_DISCRTRY, &clp->cl_flags);
error = nfs_create_rpc_client(clp, timeparms, RPC_AUTH_GSS_KRB5I);
if (error == -EINVAL)
- error = nfs_create_rpc_client(clp, timeparms, RPC_AUTH_NULL);
+ error = nfs_create_rpc_client(clp, timeparms, RPC_AUTH_UNIX);
if (error < 0)
goto error;
task->tk_timeout = 0;
spin_lock(&tbl->slot_tbl_lock);
- if (test_bit(NFS4_SESSION_DRAINING, &session->session_state) &&
+ if (test_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state) &&
!args->sa_privileged) {
/* The state manager will wait until the slot table is empty */
dprintk("%s session is draining\n", __func__);
tbl->highest_used_slotid = new_max;
else {
tbl->highest_used_slotid = NFS4_NO_SLOT;
- nfs4_session_drain_complete(tbl->session, tbl);
+ nfs4_slot_tbl_drain_complete(tbl);
}
}
dprintk("%s: slotid %u highest_used_slotid %d\n", __func__,
struct nfs4_slot *slot = pslot;
struct nfs4_slot_table *tbl = slot->table;
- if (nfs4_session_draining(tbl->session) && !args->sa_privileged)
+ if (nfs4_slot_tbl_draining(tbl) && !args->sa_privileged)
return false;
slot->generation = tbl->generation;
args->sa_slot = slot;
};
/* Sessions */
+enum nfs4_slot_tbl_state {
+ NFS4_SLOT_TBL_DRAINING,
+};
+
#define SLOT_TABLE_SZ DIV_ROUND_UP(NFS4_MAX_SLOT_TABLE, 8*sizeof(long))
struct nfs4_slot_table {
struct nfs4_session *session; /* Parent session */
unsigned long generation; /* Generation counter for
target_highest_slotid */
struct completion complete;
+ unsigned long slot_tbl_state;
};
/*
enum nfs4_session_state {
NFS4_SESSION_INITING,
- NFS4_SESSION_DRAINING,
};
#if defined(CONFIG_NFS_V4_1)
extern int nfs4_init_session(struct nfs_server *server);
extern int nfs4_init_ds_session(struct nfs_client *, unsigned long);
-extern void nfs4_session_drain_complete(struct nfs4_session *session,
- struct nfs4_slot_table *tbl);
+extern void nfs4_slot_tbl_drain_complete(struct nfs4_slot_table *tbl);
-static inline bool nfs4_session_draining(struct nfs4_session *session)
+static inline bool nfs4_slot_tbl_draining(struct nfs4_slot_table *tbl)
{
- return !!test_bit(NFS4_SESSION_DRAINING, &session->session_state);
+ return !!test_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state);
}
bool nfs41_wake_and_assign_slot(struct nfs4_slot_table *tbl,
if (ses == NULL)
return;
tbl = &ses->fc_slot_table;
- if (test_and_clear_bit(NFS4_SESSION_DRAINING, &ses->session_state)) {
+ if (test_and_clear_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state)) {
spin_lock(&tbl->slot_tbl_lock);
nfs41_wake_slot_table(tbl);
spin_unlock(&tbl->slot_tbl_lock);
/*
* Signal state manager thread if session fore channel is drained
*/
-void nfs4_session_drain_complete(struct nfs4_session *session,
- struct nfs4_slot_table *tbl)
+void nfs4_slot_tbl_drain_complete(struct nfs4_slot_table *tbl)
{
- if (nfs4_session_draining(session))
+ if (nfs4_slot_tbl_draining(tbl))
complete(&tbl->complete);
}
-static int nfs4_wait_on_slot_tbl(struct nfs4_slot_table *tbl)
+static int nfs4_drain_slot_tbl(struct nfs4_slot_table *tbl)
{
+ set_bit(NFS4_SLOT_TBL_DRAINING, &tbl->slot_tbl_state);
spin_lock(&tbl->slot_tbl_lock);
if (tbl->highest_used_slotid != NFS4_NO_SLOT) {
INIT_COMPLETION(tbl->complete);
struct nfs4_session *ses = clp->cl_session;
int ret = 0;
- set_bit(NFS4_SESSION_DRAINING, &ses->session_state);
/* back channel */
- ret = nfs4_wait_on_slot_tbl(&ses->bc_slot_table);
+ ret = nfs4_drain_slot_tbl(&ses->bc_slot_table);
if (ret)
return ret;
/* fore channel */
- return nfs4_wait_on_slot_tbl(&ses->fc_slot_table);
+ return nfs4_drain_slot_tbl(&ses->fc_slot_table);
}
static void nfs41_finish_session_reset(struct nfs_client *clp)
static int nilfs_set_page_dirty(struct page *page)
{
- int ret = __set_page_dirty_buffers(page);
+ int ret = __set_page_dirty_nobuffers(page);
- if (ret) {
+ if (page_has_buffers(page)) {
struct inode *inode = page->mapping->host;
- unsigned nr_dirty = 1 << (PAGE_SHIFT - inode->i_blkbits);
+ unsigned nr_dirty = 0;
+ struct buffer_head *bh, *head;
- nilfs_set_file_dirty(inode, nr_dirty);
+ /*
+ * This page is locked by callers, and no other thread
+ * concurrently marks its buffers dirty since they are
+ * only dirtied through routines in fs/buffer.c in
+ * which call sites of mark_buffer_dirty are protected
+ * by page lock.
+ */
+ bh = head = page_buffers(page);
+ do {
+ /* Do not mark hole blocks dirty */
+ if (buffer_dirty(bh) || !buffer_mapped(bh))
+ continue;
+
+ set_buffer_dirty(bh);
+ nr_dirty++;
+ } while (bh = bh->b_this_page, bh != head);
+
+ if (nr_dirty)
+ nilfs_set_file_dirty(inode, nr_dirty);
}
return ret;
}
&hole_size, &rec, &is_last);
if (ret) {
mlog_errno(ret);
- goto out;
+ goto out_unlock;
}
if (rec.e_blkno == 0ULL) {
ret = ocfs2_inode_lock(inode, NULL, 1);
if (ret < 0) {
mlog_errno(ret);
- goto out_sems;
+ goto out;
}
ocfs2_inode_unlock(inode, 1);
(xfs_off_t)(page->index + 1) << PAGE_CACHE_SHIFT,
i_size_read(inode));
+ /*
+ * If the current map does not span the entire page we are about to try
+ * to write, then give up. The only way we can write a page that spans
+ * multiple mappings in a single writeback iteration is via the
+ * xfs_vm_writepage() function. Data integrity writeback requires the
+ * entire page to be written in a single attempt, otherwise the part of
+ * the page we don't write here doesn't get written as part of the data
+ * integrity sync.
+ *
+ * For normal writeback, we also don't attempt to write partial pages
+ * here as it simply means that write_cache_pages() will see it under
+ * writeback and ignore the page until some point in the future, at
+ * which time this will be the only page in the file that needs
+ * writeback. Hence for more optimal IO patterns, we should always
+ * avoid partial page writeback due to multiple mappings on a page here.
+ */
+ if (!xfs_imap_valid(inode, imap, end_offset))
+ goto fail_unlock_page;
+
len = 1 << inode->i_blkbits;
p_offset = min_t(unsigned long, end_offset & (PAGE_CACHE_SIZE - 1),
PAGE_CACHE_SIZE);
*/
int
xfs_attr_shortform_allfit(
- struct xfs_buf *bp,
- struct xfs_inode *dp)
+ struct xfs_buf *bp,
+ struct xfs_inode *dp)
{
- xfs_attr_leafblock_t *leaf;
- xfs_attr_leaf_entry_t *entry;
+ struct xfs_attr_leafblock *leaf;
+ struct xfs_attr_leaf_entry *entry;
xfs_attr_leaf_name_local_t *name_loc;
- int bytes, i;
+ struct xfs_attr3_icleaf_hdr leafhdr;
+ int bytes;
+ int i;
leaf = bp->b_addr;
- ASSERT(leaf->hdr.info.magic == cpu_to_be16(XFS_ATTR_LEAF_MAGIC));
+ xfs_attr3_leaf_hdr_from_disk(&leafhdr, leaf);
+ entry = xfs_attr3_leaf_entryp(leaf);
- entry = &leaf->entries[0];
bytes = sizeof(struct xfs_attr_sf_hdr);
- for (i = 0; i < be16_to_cpu(leaf->hdr.count); entry++, i++) {
+ for (i = 0; i < leafhdr.count; entry++, i++) {
if (entry->flags & XFS_ATTR_INCOMPLETE)
continue; /* don't copy partial entries */
if (!(entry->flags & XFS_ATTR_LOCAL))
return(0);
if (be16_to_cpu(name_loc->valuelen) >= XFS_ATTR_SF_ENTSIZE_MAX)
return(0);
- bytes += sizeof(struct xfs_attr_sf_entry)-1
+ bytes += sizeof(struct xfs_attr_sf_entry) - 1
+ name_loc->namelen
+ be16_to_cpu(name_loc->valuelen);
}
if ((dp->i_mount->m_flags & XFS_MOUNT_ATTR2) &&
(dp->i_d.di_format != XFS_DINODE_FMT_BTREE) &&
(bytes == sizeof(struct xfs_attr_sf_hdr)))
- return(-1);
- return(xfs_attr_shortform_bytesfit(dp, bytes));
+ return -1;
+ return xfs_attr_shortform_bytesfit(dp, bytes);
}
/*
if (!xfs_attr_namesp_match(args->flags, entry->flags))
continue;
args->index = probe;
+ args->valuelen = be32_to_cpu(name_rmt->valuelen);
args->rmtblkno = be32_to_cpu(name_rmt->valueblk);
args->rmtblkcnt = XFS_B_TO_FSB(args->dp->i_mount,
- be32_to_cpu(name_rmt->valuelen));
+ args->valuelen);
return XFS_ERROR(EEXIST);
}
}
{
xfs_buftarg_t *btp;
- btp = kmem_zalloc(sizeof(*btp), KM_SLEEP);
+ btp = kmem_zalloc(sizeof(*btp), KM_SLEEP | KM_NOFS);
btp->bt_mount = mp;
btp->bt_dev = bdev->bd_dev;
break;
return;
case XFS_ATTR_LEAF_MAGIC:
+ case XFS_ATTR3_LEAF_MAGIC:
bp->b_ops = &xfs_attr3_leaf_buf_ops;
bp->b_ops->verify_read(bp);
return;
ASSERT(nirecs >= 1);
if (nirecs > 1) {
- map = kmem_zalloc(nirecs * sizeof(struct xfs_buf_map), KM_SLEEP);
+ map = kmem_zalloc(nirecs * sizeof(struct xfs_buf_map),
+ KM_SLEEP | KM_NOFS);
if (!map)
return ENOMEM;
*mapp = map;
* Optimize the one-block case.
*/
if (nfsb != 1)
- irecs = kmem_zalloc(sizeof(irec) * nfsb, KM_SLEEP);
+ irecs = kmem_zalloc(sizeof(irec) * nfsb,
+ KM_SLEEP | KM_NOFS);
nirecs = nfsb;
error = xfs_bmapi_read(dp, (xfs_fileoff_t)bno, nfsb, irecs,
mp->m_sb.sb_blocksize);
map_info = kmem_zalloc(offsetof(struct xfs_dir2_leaf_map_info, map) +
(length * sizeof(struct xfs_bmbt_irec)),
- KM_SLEEP);
+ KM_SLEEP | KM_NOFS);
map_info->map_size = length;
/*
{
ASSERT(atomic_read(&efip->efi_next_extent) >= nextents);
if (atomic_sub_and_test(nextents, &efip->efi_next_extent)) {
- __xfs_efi_release(efip);
-
/* recovery needs us to drop the EFI reference, too */
if (test_bit(XFS_EFI_RECOVERED, &efip->efi_flags))
__xfs_efi_release(efip);
+
+ __xfs_efi_release(efip);
+ /* efip may now have been freed, do not reference it again. */
}
}
new_lv = kmem_zalloc(sizeof(*new_lv) +
niovecs * sizeof(struct xfs_log_iovec),
- KM_SLEEP);
+ KM_SLEEP|KM_NOFS);
/* The allocated iovec region lies beyond the log vector. */
new_lv->lv_iovecp = (struct xfs_log_iovec *)&new_lv[1];
xfs_mount_t *mp;
int nimap;
uint resblks;
- uint rounding;
+ xfs_off_t rounding;
int rt;
xfs_fileoff_t startoffset_fsb;
xfs_trans_t *tp;
inode_dio_wait(VFS_I(ip));
}
- rounding = max_t(uint, 1 << mp->m_sb.sb_blocklog, PAGE_CACHE_SIZE);
+ rounding = max_t(xfs_off_t, 1 << mp->m_sb.sb_blocklog, PAGE_CACHE_SIZE);
ioffset = offset & ~(rounding - 1);
error = -filemap_write_and_wait_range(VFS_I(ip)->i_mapping,
ioffset, -1);
unsigned long long *sta);
int acpi_bus_get_status(struct acpi_device *device);
-#ifdef CONFIG_PM
int acpi_bus_set_power(acpi_handle handle, int state);
const char *acpi_power_state_string(int state);
int acpi_device_get_power(struct acpi_device *device, int *state);
int acpi_bus_init_power(struct acpi_device *device);
int acpi_bus_update_power(acpi_handle handle, int *state_p);
bool acpi_bus_power_manageable(acpi_handle handle);
+
+#ifdef CONFIG_PM
bool acpi_bus_can_wakeup(acpi_handle handle);
-#else /* !CONFIG_PM */
-static inline int acpi_bus_set_power(acpi_handle handle, int state)
-{
- return 0;
-}
-static inline const char *acpi_power_state_string(int state)
-{
- return "D0";
-}
-static inline int acpi_device_get_power(struct acpi_device *device, int *state)
-{
- return 0;
-}
-static inline int acpi_device_set_power(struct acpi_device *device, int state)
-{
- return 0;
-}
-static inline int acpi_bus_init_power(struct acpi_device *device)
-{
- return 0;
-}
-static inline int acpi_bus_update_power(acpi_handle handle, int *state_p)
-{
- return 0;
-}
-static inline bool acpi_bus_power_manageable(acpi_handle handle)
-{
- return false;
-}
-static inline bool acpi_bus_can_wakeup(acpi_handle handle)
-{
- return false;
-}
-#endif /* !CONFIG_PM */
+#else
+static inline bool acpi_bus_can_wakeup(acpi_handle handle) { return false; }
+#endif
#ifdef CONFIG_ACPI_PROC_EVENT
int acpi_bus_generate_proc_event(struct acpi_device *device, u8 type, int data);
* @dev: struct device of this controller
* @acpi_dma_xlate: callback function to find a suitable channel
* @data: private data used by a callback function
+ * @base_request_line: first supported request line (CSRT)
+ * @end_request_line: last supported request line (CSRT)
*/
struct acpi_dma {
struct list_head dma_controllers;
struct dma_chan *(*acpi_dma_xlate)
(struct acpi_dma_spec *, struct acpi_dma *);
void *data;
+ unsigned short base_request_line;
+ unsigned short end_request_line;
};
/* Used with acpi_dma_simple_xlate() */
#define BCMA_CORE_I2S 0x834
#define BCMA_CORE_SDR_DDR1_MEM_CTL 0x835 /* SDR/DDR1 memory controller core */
#define BCMA_CORE_SHIM 0x837 /* SHIM component in ubus/6362 */
-#define BCMA_CORE_ARM_CR4 0x83e
+#define BCMA_CORE_PHY_AC 0x83B
+#define BCMA_CORE_PCIE2 0x83C /* PCI Express Gen2 */
+#define BCMA_CORE_USB30_DEV 0x83D
+#define BCMA_CORE_ARM_CR4 0x83E
#define BCMA_CORE_DEFAULT 0xFFF
#define BCMA_MAX_NR_CORES 16
+#ifndef _LINUX_BRCMPHY_H
+#define _LINUX_BRCMPHY_H
+
#define PHY_ID_BCM50610 0x0143bd60
#define PHY_ID_BCM50610M 0x0143bd70
#define PHY_ID_BCM5241 0x0143bc30
#define PHY_BRCM_CLEAR_RGMII_MODE 0x00004000
#define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00008000
#define PHY_BCM_FLAGS_VALID 0x80000000
+
+#endif /* _LINUX_BRCMPHY_H */
extern __printf(2, 3)
int __trace_printk(unsigned long ip, const char *fmt, ...);
+extern int __trace_bputs(unsigned long ip, const char *str);
+extern int __trace_puts(unsigned long ip, const char *str, int size);
+
/**
* trace_puts - write a string into the ftrace buffer
* @str: the string to record
* (1 when __trace_bputs is used, strlen(str) when __trace_puts is used)
*/
-extern int __trace_bputs(unsigned long ip, const char *str);
-extern int __trace_puts(unsigned long ip, const char *str, int size);
#define trace_puts(str) ({ \
static const char *trace_printk_fmt \
__attribute__((section("__trace_printk_fmt"))) = \
/**
* struct ab8500_platform_data - AB8500 platform data
* @irq_base: start of AB8500 IRQs, AB8500_NR_IRQS will be used
- * @pm_power_off: Should machine pm power off hook be registered or not
* @init: board-specific initialization after detection of ab8500
* @regulator: machine-specific constraints for regulators
*/
struct ab8500_platform_data {
int irq_base;
- bool pm_power_off;
void (*init) (struct ab8500 *);
struct ab8500_regulator_platform_data *regulator;
struct abx500_gpio_platform_data *gpio;
}
netdev_features_t netdev_increment_features(netdev_features_t all,
netdev_features_t one, netdev_features_t mask);
+
+/* Allow TSO being used on stacked device :
+ * Performing the GSO segmentation before last device
+ * is a performance improvement.
+ */
+static inline netdev_features_t netdev_add_tso_features(netdev_features_t features,
+ netdev_features_t mask)
+{
+ return netdev_increment_features(features, NETIF_F_ALL_TSO, mask);
+}
+
int __netdev_update_features(struct net_device *dev);
void netdev_update_features(struct net_device *dev);
void netdev_change_features(struct net_device *dev);
void acpiphp_init(void);
void acpiphp_enumerate_slots(struct pci_bus *bus, acpi_handle handle);
void acpiphp_remove_slots(struct pci_bus *bus);
+void acpiphp_check_host_bridge(acpi_handle handle);
#else
static inline void acpiphp_init(void) { }
static inline void acpiphp_enumerate_slots(struct pci_bus *bus,
acpi_handle handle) { }
static inline void acpiphp_remove_slots(struct pci_bus *bus) { }
+static inline void acpiphp_check_host_bridge(acpi_handle handle) { }
#endif
#else /* CONFIG_ACPI */
#ifndef __CLK_LPSS_H
#define __CLK_LPSS_H
+struct lpss_clk_data {
+ const char *name;
+ struct clk *clk;
+};
+
extern int lpt_clk_init(void);
#endif /* __CLK_LPSS_H */
int DTR_present;
int (*get_context_loss_count)(struct device *);
- void (*set_forceidle)(struct device *);
- void (*set_noidle)(struct device *);
void (*enable_wakeup)(struct device *, bool);
};
#include <stdarg.h>
#include <linux/init.h>
#include <linux/kern_levels.h>
+#include <linux/linkage.h>
extern const char linux_banner[];
extern const char linux_proc_banner[];
extern struct bus_type rio_bus_type;
extern struct device rio_bus;
-extern struct list_head rio_devices; /* list of all devices */
struct rio_mport;
struct rio_dev;
* @name: Port name string
* @priv: Master port private data
* @dma: DMA device associated with mport
+ * @nscan: RapidIO network enumeration/discovery operations
*/
struct rio_mport {
struct list_head dbells; /* list of doorbell events */
#ifdef CONFIG_RAPIDIO_DMA_ENGINE
struct dma_device dma;
#endif
+ struct rio_scan *nscan;
};
+/*
+ * Enumeration/discovery control flags
+ */
+#define RIO_SCAN_ENUM_NO_WAIT 0x00000001 /* Do not wait for enum completed */
+
struct rio_id_table {
u16 start; /* logical minimal id */
u32 max; /* max number of IDs in table */
}
#endif /* CONFIG_RAPIDIO_DMA_ENGINE */
+/**
+ * struct rio_scan - RIO enumeration and discovery operations
+ * @enumerate: Callback to perform RapidIO fabric enumeration.
+ * @discover: Callback to perform RapidIO fabric discovery.
+ */
+struct rio_scan {
+ int (*enumerate)(struct rio_mport *mport, u32 flags);
+ int (*discover)(struct rio_mport *mport, u32 flags);
+};
+
/* Architecture and hardware-specific functions */
extern int rio_register_mport(struct rio_mport *);
extern int rio_open_inb_mbox(struct rio_mport *, void *, int, int);
extern struct rio_dev *rio_get_device(u16 vid, u16 did, struct rio_dev *from);
extern struct rio_dev *rio_get_asm(u16 vid, u16 did, u16 asm_vid, u16 asm_did,
struct rio_dev *from);
+extern int rio_init_mports(void);
#endif /* LINUX_RIO_DRV_H */
extern void cred_to_ucred(struct pid *pid, const struct cred *cred, struct ucred *ucred);
-extern int memcpy_fromiovec(unsigned char *kdata, struct iovec *iov, int len);
extern int memcpy_fromiovecend(unsigned char *kdata, const struct iovec *iov,
int offset, int len);
extern int csum_partial_copy_fromiovecend(unsigned char *kdata,
unsigned int len, __wsum *csump);
extern int verify_iovec(struct msghdr *m, struct iovec *iov, struct sockaddr_storage *address, int mode);
-extern int memcpy_toiovec(struct iovec *v, unsigned char *kdata, int len);
extern int memcpy_toiovecend(const struct iovec *v, unsigned char *kdata,
int offset, int len);
extern int move_addr_to_kernel(void __user *uaddr, int ulen, struct sockaddr_storage *kaddr);
}
unsigned long iov_shorten(struct iovec *iov, unsigned long nr_segs, size_t to);
+
+int memcpy_fromiovec(unsigned char *kdata, struct iovec *iov, int len);
+int memcpy_toiovec(struct iovec *iov, unsigned char *kdata, int len);
#endif
}
/**
- * gadget_is_superspeed() - return true if the hardware handles
- * supperspeed
- * @g: controller that might support supper speed
+ * gadget_is_superspeed() - return true if the hardware handles superspeed
+ * @g: controller that might support superspeed
*/
static inline int gadget_is_superspeed(struct usb_gadget *g)
{
struct usb_serial_port *port, struct ktermios *old);
void (*break_ctl)(struct tty_struct *tty, int break_state);
int (*chars_in_buffer)(struct tty_struct *tty);
+ void (*wait_until_sent)(struct tty_struct *tty, long timeout);
+ bool (*tx_empty)(struct usb_serial_port *port);
void (*throttle)(struct tty_struct *tty);
void (*unthrottle)(struct tty_struct *tty);
int (*tiocmget)(struct tty_struct *tty);
extern int usb_serial_generic_resume(struct usb_serial *serial);
extern int usb_serial_generic_write_room(struct tty_struct *tty);
extern int usb_serial_generic_chars_in_buffer(struct tty_struct *tty);
+extern void usb_serial_generic_wait_until_sent(struct tty_struct *tty,
+ long timeout);
extern void usb_serial_generic_read_bulk_callback(struct urb *urb);
extern void usb_serial_generic_write_bulk_callback(struct urb *urb);
extern void usb_serial_generic_throttle(struct tty_struct *tty);
int vc_allocate(unsigned int console);
int vc_cons_allocated(unsigned int console);
int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int lines);
-void vc_deallocate(unsigned int console);
+struct vc_data *vc_deallocate(unsigned int console);
void reset_palette(struct vc_data *vc);
void do_blank_screen(int entering_gfx);
void do_unblank_screen(int leaving_gfx);
if (!ret) \
break; \
} \
+ if (!ret && (condition)) \
+ ret = 1; \
finish_wait(&wq, &__wait); \
} while (0)
* wake_up() has to be called after changing any variable that could
* change the result of the wait condition.
*
- * The function returns 0 if the @timeout elapsed, and the remaining
- * jiffies if the condition evaluated to true before the timeout elapsed.
+ * The function returns 0 if the @timeout elapsed, or the remaining
+ * jiffies (at least 1) if the @condition evaluated to %true before
+ * the @timeout elapsed.
*/
#define wait_event_timeout(wq, condition, timeout) \
({ \
ret = -ERESTARTSYS; \
break; \
} \
+ if (!ret && (condition)) \
+ ret = 1; \
finish_wait(&wq, &__wait); \
} while (0)
* wake_up() has to be called after changing any variable that could
* change the result of the wait condition.
*
- * The function returns 0 if the @timeout elapsed, -ERESTARTSYS if it
- * was interrupted by a signal, and the remaining jiffies otherwise
- * if the condition evaluated to true before the timeout elapsed.
+ * Returns:
+ * 0 if the @timeout elapsed, -%ERESTARTSYS if it was interrupted by
+ * a signal, or the remaining jiffies (at least 1) if the @condition
+ * evaluated to %true before the @timeout elapsed.
*/
#define wait_event_interruptible_timeout(wq, condition, timeout) \
({ \
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls to
* this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
- * mixed for a single hardware.
+ * mixed for a single hardware. Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
*
* In process context use instead ieee80211_rx_ni().
*
* (internally defers to a tasklet.)
*
* Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
- * be mixed for a single hardware.
+ * be mixed for a single hardware.Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
* (internally disables bottom halves).
*
* Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
- * not be mixed for a single hardware.
+ * not be mixed for a single hardware. Must not run concurrently with
+ * ieee80211_tx_status() or ieee80211_tx_status_ni().
*
* @hw: the hardware this frame came in on
* @skb: the buffer to receive, owned by mac80211 after this call
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls
* to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
- * may not be mixed for a single hardware.
+ * may not be mixed for a single hardware. Must not run concurrently with
+ * ieee80211_rx() or ieee80211_rx_ni().
*
* @hw: the hardware the frame was transmitted by
* @skb: the frame that was transmitted, owned by mac80211 after this call
} u;
};
-typedef void nf_logfn(u_int8_t pf,
+typedef void nf_logfn(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
#define _KER_NFNETLINK_LOG_H
void
-nfulnl_log_packet(u_int8_t pf,
+nfulnl_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
#define VIRTIO_CONSOLE_F_SIZE 0 /* Does host provide console size? */
#define VIRTIO_CONSOLE_F_MULTIPORT 1 /* Does host provide multiple ports? */
-#define VIRTIO_CONSOLE_BAD_ID (~(u32)0)
+#define VIRTIO_CONSOLE_BAD_ID (~(__u32)0)
struct virtio_console_config {
/* colums of the screens */
int otime, struct list_head *pt)
{
int i;
+ int progress;
- if (sma->complex_count || sops == NULL) {
- if (update_queue(sma, -1, pt))
+ progress = 1;
+retry_global:
+ if (sma->complex_count) {
+ if (update_queue(sma, -1, pt)) {
+ progress = 1;
otime = 1;
+ sops = NULL;
+ }
}
+ if (!progress)
+ goto done;
if (!sops) {
/* No semops; something special is going on. */
for (i = 0; i < sma->sem_nsems; i++) {
- if (update_queue(sma, i, pt))
+ if (update_queue(sma, i, pt)) {
otime = 1;
+ progress = 1;
+ }
}
- goto done;
+ goto done_checkretry;
}
/* Check the semaphores that were modified. */
if (sops[i].sem_op > 0 ||
(sops[i].sem_op < 0 &&
sma->sem_base[sops[i].sem_num].semval == 0))
- if (update_queue(sma, sops[i].sem_num, pt))
+ if (update_queue(sma, sops[i].sem_num, pt)) {
otime = 1;
+ progress = 1;
+ }
+ }
+done_checkretry:
+ if (progress) {
+ progress = 0;
+ goto retry_global;
}
done:
if (otime)
* @seq: netlink audit message sequence (serial) number
* @data: payload data
* @datasz: size of payload data
- * @loginuid: loginuid of sender
- * @sessionid: sessionid for netlink audit message
- * @sid: SE Linux Security ID of sender
*/
int audit_receive_filter(int type, int pid, int seq, void *data, size_t datasz)
{
out_reg:
/* Don't let event modules unload while probe registered */
ret = try_module_get(file->event_call->mod);
- if (!ret)
+ if (!ret) {
+ ret = -EBUSY;
goto out_free;
+ }
ret = __ftrace_event_enable_disable(file, 1, 1);
if (ret < 0)
obj-y += bcd.o div64.o sort.o parser.o halfmd4.o debug_locks.o random32.o \
bust_spinlocks.o hexdump.o kasprintf.o bitmap.o scatterlist.o \
- gcd.o lcm.o list_sort.o uuid.o flex_array.o \
+ gcd.o lcm.o list_sort.o uuid.o flex_array.o iovec.o \
bsearch.o find_last_bit.o find_next_bit.o llist.o memweight.o kfifo.o
obj-y += string_helpers.o
obj-$(CONFIG_TEST_STRING_HELPERS) += test-string_helpers.o
--- /dev/null
+#include <linux/uaccess.h>
+#include <linux/export.h>
+#include <linux/uio.h>
+
+/*
+ * Copy iovec to kernel. Returns -EFAULT on error.
+ *
+ * Note: this modifies the original iovec.
+ */
+
+int memcpy_fromiovec(unsigned char *kdata, struct iovec *iov, int len)
+{
+ while (len > 0) {
+ if (iov->iov_len) {
+ int copy = min_t(unsigned int, len, iov->iov_len);
+ if (copy_from_user(kdata, iov->iov_base, copy))
+ return -EFAULT;
+ len -= copy;
+ kdata += copy;
+ iov->iov_base += copy;
+ iov->iov_len -= copy;
+ }
+ iov++;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(memcpy_fromiovec);
+
+/*
+ * Copy kernel to iovec. Returns -EFAULT on error.
+ *
+ * Note: this modifies the original iovec.
+ */
+
+int memcpy_toiovec(struct iovec *iov, unsigned char *kdata, int len)
+{
+ while (len > 0) {
+ if (iov->iov_len) {
+ int copy = min_t(unsigned int, iov->iov_len, len);
+ if (copy_to_user(iov->iov_base, kdata, copy))
+ return -EFAULT;
+ kdata += copy;
+ len -= copy;
+ iov->iov_len -= copy;
+ iov->iov_base += copy;
+ }
+ iov++;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(memcpy_toiovec);
if (waiter->node != n)
continue;
+ list_del(&waiter->list);
waiter->woken = 1;
mb();
wake_up_process(waiter->process);
- list_del(&waiter->list);
}
spin_unlock(&klist_remove_lock);
knode_set_klist(n, NULL);
"rM" ((USItype)(bh)), \
"rM" ((USItype)(al)), \
"rM" ((USItype)(bl)))
-#if defined(_PA_RISC1_1)
+#if 0 && defined(_PA_RISC1_1)
+/* xmpyu uses floating point register which is not allowed in Linux kernel. */
#define umul_ppmm(wh, wl, u, v) \
do { \
union {UDItype __ll; \
#define UMUL_TIME 40
#define UDIV_TIME 80
#endif
-#ifndef LONGLONG_STANDALONE
+#if 0 /* #ifndef LONGLONG_STANDALONE */
#define udiv_qrnnd(q, r, n1, n0, d) \
do { USItype __r; \
(q) = __udiv_qrnnd(&__r, (n1), (n0), (d)); \
pte_unmap(pte);
spin_lock(&mm->page_table_lock);
BUG_ON(!pmd_none(*pmd));
- set_pmd_at(mm, address, pmd, _pmd);
+ /*
+ * We can only use set_pmd_at when establishing
+ * hugepmds and never for establishing regular pmds that
+ * points to regular pagetables. Use pmd_populate for that
+ */
+ pmd_populate(mm, pmd, pmd_pgtable(_pmd));
spin_unlock(&mm->page_table_lock);
anon_vma_unlock_write(vma->anon_vma);
goto out;
if (mem_cgroup_disabled())
return NULL;
- VM_BUG_ON(PageSwapCache(page));
-
if (PageTransHuge(page)) {
nr_pages <<= compound_order(page);
VM_BUG_ON(!PageTransHuge(page));
if (page_mapped(page))
return;
VM_BUG_ON(page->mapping && !PageAnon(page));
+ /*
+ * If the page is in swap cache, uncharge should be deferred
+ * to the swap path, which also properly accounts swap usage
+ * and handles memcg lifetime.
+ *
+ * Note that this check is not stable and reclaim may add the
+ * page to swap cache at any time after this. However, if the
+ * page is not in swap cache by the time page->mapcount hits
+ * 0, there won't be any page table references to the swap
+ * slot, and reclaim will free it and not actually write the
+ * page to disk.
+ */
if (PageSwapCache(page))
return;
__mem_cgroup_uncharge_common(page, MEM_CGROUP_CHARGE_TYPE_ANON, false);
start = phys_start_pfn << PAGE_SHIFT;
size = nr_pages * PAGE_SIZE;
ret = release_mem_region_adjustable(&iomem_resource, start, size);
- if (ret)
- pr_warn("Unable to release resource <%016llx-%016llx> (%d)\n",
- start, start + size - 1, ret);
+ if (ret) {
+ resource_size_t endres = start + size - 1;
+
+ pr_warn("Unable to release resource <%pa-%pa> (%d)\n",
+ &start, &endres, ret);
+ }
sections_to_remove = nr_pages / PAGES_PER_SECTION;
for (i = 0; i < sections_to_remove; i++) {
pte = arch_make_huge_pte(pte, vma, new, 0);
}
#endif
- flush_cache_page(vma, addr, pte_pfn(pte));
+ flush_dcache_page(new);
set_pte_at(mm, addr, ptep, pte);
if (PageHuge(new)) {
int id;
/*
- * srcu_read_lock() here will block synchronize_srcu() in
- * mmu_notifier_unregister() until all registered
- * ->release() callouts this function makes have
- * returned.
+ * SRCU here will block mmu_notifier_unregister until
+ * ->release returns.
*/
id = srcu_read_lock(&srcu);
+ hlist_for_each_entry_rcu(mn, &mm->mmu_notifier_mm->list, hlist)
+ /*
+ * If ->release runs before mmu_notifier_unregister it must be
+ * handled, as it's the only way for the driver to flush all
+ * existing sptes and stop the driver from establishing any more
+ * sptes before all the pages in the mm are freed.
+ */
+ if (mn->ops->release)
+ mn->ops->release(mn, mm);
+ srcu_read_unlock(&srcu, id);
+
spin_lock(&mm->mmu_notifier_mm->lock);
while (unlikely(!hlist_empty(&mm->mmu_notifier_mm->list))) {
mn = hlist_entry(mm->mmu_notifier_mm->list.first,
struct mmu_notifier,
hlist);
-
/*
- * Unlink. This will prevent mmu_notifier_unregister()
- * from also making the ->release() callout.
+ * We arrived before mmu_notifier_unregister so
+ * mmu_notifier_unregister will do nothing other than to wait
+ * for ->release to finish and for mmu_notifier_unregister to
+ * return.
*/
hlist_del_init_rcu(&mn->hlist);
- spin_unlock(&mm->mmu_notifier_mm->lock);
-
- /*
- * Clear sptes. (see 'release' description in mmu_notifier.h)
- */
- if (mn->ops->release)
- mn->ops->release(mn, mm);
-
- spin_lock(&mm->mmu_notifier_mm->lock);
}
spin_unlock(&mm->mmu_notifier_mm->lock);
/*
- * All callouts to ->release() which we have done are complete.
- * Allow synchronize_srcu() in mmu_notifier_unregister() to complete
- */
- srcu_read_unlock(&srcu, id);
-
- /*
- * mmu_notifier_unregister() may have unlinked a notifier and may
- * still be calling out to it. Additionally, other notifiers
- * may have been active via vmtruncate() et. al. Block here
- * to ensure that all notifier callouts for this mm have been
- * completed and the sptes are really cleaned up before returning
- * to exit_mmap().
+ * synchronize_srcu here prevents mmu_notifier_release from returning to
+ * exit_mmap (which would proceed with freeing all pages in the mm)
+ * until the ->release method returns, if it was invoked by
+ * mmu_notifier_unregister.
+ *
+ * The mmu_notifier_mm can't go away from under us because one mm_count
+ * is held by exit_mmap.
*/
synchronize_srcu(&srcu);
}
{
BUG_ON(atomic_read(&mm->mm_count) <= 0);
- spin_lock(&mm->mmu_notifier_mm->lock);
if (!hlist_unhashed(&mn->hlist)) {
+ /*
+ * SRCU here will force exit_mmap to wait for ->release to
+ * finish before freeing the pages.
+ */
int id;
+ id = srcu_read_lock(&srcu);
/*
- * Ensure we synchronize up with __mmu_notifier_release().
+ * exit_mmap will block in mmu_notifier_release to guarantee
+ * that ->release is called before freeing the pages.
*/
- id = srcu_read_lock(&srcu);
-
- hlist_del_rcu(&mn->hlist);
- spin_unlock(&mm->mmu_notifier_mm->lock);
-
if (mn->ops->release)
mn->ops->release(mn, mm);
+ srcu_read_unlock(&srcu, id);
+ spin_lock(&mm->mmu_notifier_mm->lock);
/*
- * Allow __mmu_notifier_release() to complete.
+ * Can not use list_del_rcu() since __mmu_notifier_release
+ * can delete it before we hold the lock.
*/
- srcu_read_unlock(&srcu, id);
- } else
+ hlist_del_init_rcu(&mn->hlist);
spin_unlock(&mm->mmu_notifier_mm->lock);
+ }
/*
- * Wait for any running method to finish, including ->release() if it
- * was run by __mmu_notifier_release() instead of us.
+ * Wait for any running method to finish, of course including
+ * ->release if it was run by mmu_notifier_relase instead of us.
*/
synchronize_srcu(&srcu);
for (pages = 0; pos < end; pos += PAGE_SIZE, pages++) {
if (poison)
memset((void *)pos, poison, PAGE_SIZE);
- free_reserved_page(virt_to_page(pos));
+ free_reserved_page(virt_to_page((void *)pos));
}
if (pages && s)
return 0;
}
-static struct vm_area_struct* hugetlb_vma(unsigned long addr, struct mm_walk *walk)
-{
- struct vm_area_struct *vma;
-
- /* We don't need vma lookup at all. */
- if (!walk->hugetlb_entry)
- return NULL;
-
- VM_BUG_ON(!rwsem_is_locked(&walk->mm->mmap_sem));
- vma = find_vma(walk->mm, addr);
- if (vma && vma->vm_start <= addr && is_vm_hugetlb_page(vma))
- return vma;
-
- return NULL;
-}
-
#else /* CONFIG_HUGETLB_PAGE */
-static struct vm_area_struct* hugetlb_vma(unsigned long addr, struct mm_walk *walk)
-{
- return NULL;
-}
-
static int walk_hugetlb_range(struct vm_area_struct *vma,
unsigned long addr, unsigned long end,
struct mm_walk *walk)
if (!walk->mm)
return -EINVAL;
+ VM_BUG_ON(!rwsem_is_locked(&walk->mm->mmap_sem));
+
pgd = pgd_offset(walk->mm, addr);
do {
- struct vm_area_struct *vma;
+ struct vm_area_struct *vma = NULL;
next = pgd_addr_end(addr, end);
/*
- * handle hugetlb vma individually because pagetable walk for
- * the hugetlb page is dependent on the architecture and
- * we can't handled it in the same manner as non-huge pages.
+ * This function was not intended to be vma based.
+ * But there are vma special cases to be handled:
+ * - hugetlb vma's
+ * - VM_PFNMAP vma's
*/
- vma = hugetlb_vma(addr, walk);
+ vma = find_vma(walk->mm, addr);
if (vma) {
- if (vma->vm_end < next)
+ /*
+ * There are no page structures backing a VM_PFNMAP
+ * range, so do not allow split_huge_page_pmd().
+ */
+ if ((vma->vm_start <= addr) &&
+ (vma->vm_flags & VM_PFNMAP)) {
next = vma->vm_end;
+ pgd = pgd_offset(walk->mm, next);
+ continue;
+ }
/*
- * Hugepage is very tightly coupled with vma, so
- * walk through hugetlb entries within a given vma.
+ * Handle hugetlb vma individually because pagetable
+ * walk for the hugetlb page is dependent on the
+ * architecture and we can't handled it in the same
+ * manner as non-huge pages.
*/
- err = walk_hugetlb_range(vma, addr, next, walk);
- if (err)
- break;
- pgd = pgd_offset(walk->mm, next);
- continue;
+ if (walk->hugetlb_entry && (vma->vm_start <= addr) &&
+ is_vm_hugetlb_page(vma)) {
+ if (vma->vm_end < next)
+ next = vma->vm_end;
+ /*
+ * Hugepage is very tightly coupled with vma,
+ * so walk through hugetlb entries within a
+ * given vma.
+ */
+ err = walk_hugetlb_range(vma, addr, next, walk);
+ if (err)
+ break;
+ pgd = pgd_offset(walk->mm, next);
+ continue;
+ }
}
if (pgd_none_or_clear_bad(pgd)) {
*/
del_timer_sync(&app->join_timer);
- spin_lock(&app->lock);
+ spin_lock_bh(&app->lock);
mrp_mad_event(app, MRP_EVENT_TX);
mrp_pdu_queue(app);
- spin_unlock(&app->lock);
+ spin_unlock_bh(&app->lock);
mrp_queue_xmit(app);
batadv_originator_free(bat_priv);
free_percpu(bat_priv->bat_counters);
+ bat_priv->bat_counters = NULL;
atomic_set(&bat_priv->mesh_state, BATADV_MESH_INACTIVE);
}
kfree(orig_node);
}
+/**
+ * batadv_orig_node_free_ref - decrement the orig node refcounter and possibly
+ * schedule an rcu callback for freeing it
+ * @orig_node: the orig node to free
+ */
void batadv_orig_node_free_ref(struct batadv_orig_node *orig_node)
{
if (atomic_dec_and_test(&orig_node->refcount))
call_rcu(&orig_node->rcu, batadv_orig_node_free_rcu);
}
+/**
+ * batadv_orig_node_free_ref_now - decrement the orig node refcounter and
+ * possibly free it (without rcu callback)
+ * @orig_node: the orig node to free
+ */
+void batadv_orig_node_free_ref_now(struct batadv_orig_node *orig_node)
+{
+ if (atomic_dec_and_test(&orig_node->refcount))
+ batadv_orig_node_free_rcu(&orig_node->rcu);
+}
+
void batadv_originator_free(struct batadv_priv *bat_priv)
{
struct batadv_hashtable *hash = bat_priv->orig_hash;
void batadv_originator_free(struct batadv_priv *bat_priv);
void batadv_purge_orig_ref(struct batadv_priv *bat_priv);
void batadv_orig_node_free_ref(struct batadv_orig_node *orig_node);
+void batadv_orig_node_free_ref_now(struct batadv_orig_node *orig_node);
struct batadv_orig_node *batadv_get_orig_node(struct batadv_priv *bat_priv,
const uint8_t *addr);
struct batadv_neigh_node *
batadv_debugfs_del_meshif(dev);
free_bat_counters:
free_percpu(bat_priv->bat_counters);
+ bat_priv->bat_counters = NULL;
return ret;
}
struct batadv_tt_orig_list_entry *orig_entry;
orig_entry = container_of(rcu, struct batadv_tt_orig_list_entry, rcu);
- batadv_orig_node_free_ref(orig_entry->orig_node);
+
+ /* We are in an rcu callback here, therefore we cannot use
+ * batadv_orig_node_free_ref() and its call_rcu():
+ * An rcu_barrier() wouldn't wait for that to finish
+ */
+ batadv_orig_node_free_ref_now(orig_entry->orig_node);
kfree(orig_entry);
}
}
static void
-ebt_log_packet(u_int8_t pf, unsigned int hooknum,
- const struct sk_buff *skb, const struct net_device *in,
- const struct net_device *out, const struct nf_loginfo *loginfo,
- const char *prefix)
+ebt_log_packet(struct net *net, u_int8_t pf, unsigned int hooknum,
+ const struct sk_buff *skb, const struct net_device *in,
+ const struct net_device *out, const struct nf_loginfo *loginfo,
+ const char *prefix)
{
unsigned int bitmask;
- struct net *net = dev_net(in ? in : out);
/* FIXME: Disabled from containers until syslog ns is supported */
if (!net_eq(net, &init_net))
nf_log_packet(net, NFPROTO_BRIDGE, par->hooknum, skb,
par->in, par->out, &li, "%s", info->prefix);
else
- ebt_log_packet(NFPROTO_BRIDGE, par->hooknum, skb, par->in,
+ ebt_log_packet(net, NFPROTO_BRIDGE, par->hooknum, skb, par->in,
par->out, &li, info->prefix);
return EBT_CONTINUE;
}
return skb;
}
-static void ebt_ulog_packet(unsigned int hooknr, const struct sk_buff *skb,
- const struct net_device *in, const struct net_device *out,
- const struct ebt_ulog_info *uloginfo, const char *prefix)
+static void ebt_ulog_packet(struct net *net, unsigned int hooknr,
+ const struct sk_buff *skb,
+ const struct net_device *in,
+ const struct net_device *out,
+ const struct ebt_ulog_info *uloginfo,
+ const char *prefix)
{
ebt_ulog_packet_msg_t *pm;
size_t size, copy_len;
struct nlmsghdr *nlh;
- struct net *net = dev_net(in ? in : out);
struct ebt_ulog_net *ebt = ebt_ulog_pernet(net);
unsigned int group = uloginfo->nlgroup;
ebt_ulog_buff_t *ub = &ebt->ulog_buffers[group];
}
/* this function is registered with the netfilter core */
-static void ebt_log_packet(u_int8_t pf, unsigned int hooknum,
+static void ebt_log_packet(struct net *net, u_int8_t pf, unsigned int hooknum,
const struct sk_buff *skb, const struct net_device *in,
const struct net_device *out, const struct nf_loginfo *li,
const char *prefix)
strlcpy(loginfo.prefix, prefix, sizeof(loginfo.prefix));
}
- ebt_ulog_packet(hooknum, skb, in, out, &loginfo, prefix);
+ ebt_ulog_packet(net, hooknum, skb, in, out, &loginfo, prefix);
}
static unsigned int
ebt_ulog_tg(struct sk_buff *skb, const struct xt_action_param *par)
{
- ebt_ulog_packet(par->hooknum, skb, par->in, par->out,
+ struct net *net = dev_net(par->in ? par->in : par->out);
+
+ ebt_ulog_packet(net, par->hooknum, skb, par->in, par->out,
par->targinfo, NULL);
return EBT_CONTINUE;
}
return err;
}
-/*
- * Copy kernel to iovec. Returns -EFAULT on error.
- *
- * Note: this modifies the original iovec.
- */
-
-int memcpy_toiovec(struct iovec *iov, unsigned char *kdata, int len)
-{
- while (len > 0) {
- if (iov->iov_len) {
- int copy = min_t(unsigned int, iov->iov_len, len);
- if (copy_to_user(iov->iov_base, kdata, copy))
- return -EFAULT;
- kdata += copy;
- len -= copy;
- iov->iov_len -= copy;
- iov->iov_base += copy;
- }
- iov++;
- }
-
- return 0;
-}
-EXPORT_SYMBOL(memcpy_toiovec);
-
/*
* Copy kernel to iovec. Returns -EFAULT on error.
*/
}
EXPORT_SYMBOL(memcpy_toiovecend);
-/*
- * Copy iovec to kernel. Returns -EFAULT on error.
- *
- * Note: this modifies the original iovec.
- */
-
-int memcpy_fromiovec(unsigned char *kdata, struct iovec *iov, int len)
-{
- while (len > 0) {
- if (iov->iov_len) {
- int copy = min_t(unsigned int, len, iov->iov_len);
- if (copy_from_user(kdata, iov->iov_base, copy))
- return -EFAULT;
- len -= copy;
- kdata += copy;
- iov->iov_base += copy;
- iov->iov_len -= copy;
- }
- iov++;
- }
-
- return 0;
-}
-EXPORT_SYMBOL(memcpy_fromiovec);
-
/*
* Copy iovec from kernel. Returns -EFAULT on error.
*/
*/
struct net *net = dev_net(skb->dev);
struct ip_tunnel_net *itn;
- const struct iphdr *iph = (const struct iphdr *)skb->data;
+ const struct iphdr *iph;
const int type = icmp_hdr(skb)->type;
const int code = icmp_hdr(skb)->code;
struct ip_tunnel *t;
else
itn = net_generic(net, ipgre_net_id);
+ iph = (const struct iphdr *)skb->data;
t = ip_tunnel_lookup(itn, skb->dev->ifindex, tpi.flags,
iph->daddr, iph->saddr, tpi.key);
return skb;
}
-static void ipt_ulog_packet(unsigned int hooknum,
+static void ipt_ulog_packet(struct net *net,
+ unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const struct net_device *out,
size_t size, copy_len;
struct nlmsghdr *nlh;
struct timeval tv;
- struct net *net = dev_net(in ? in : out);
struct ulog_net *ulog = ulog_pernet(net);
/* ffs == find first bit set, necessary because userspace
static unsigned int
ulog_tg(struct sk_buff *skb, const struct xt_action_param *par)
{
- ipt_ulog_packet(par->hooknum, skb, par->in, par->out,
+ struct net *net = dev_net(par->in ? par->in : par->out);
+
+ ipt_ulog_packet(net, par->hooknum, skb, par->in, par->out,
par->targinfo, NULL);
return XT_CONTINUE;
}
-static void ipt_logfn(u_int8_t pf,
+static void ipt_logfn(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
strlcpy(loginfo.prefix, prefix, sizeof(loginfo.prefix));
}
- ipt_ulog_packet(hooknum, skb, in, out, &loginfo, prefix);
+ ipt_ulog_packet(net, hooknum, skb, in, out, &loginfo, prefix);
}
static int ulog_tg_check(const struct xt_tgchk_param *par)
unsigned int mss;
struct sk_buff *gso_skb = skb;
__sum16 newcheck;
+ bool ooo_okay, copy_destructor;
if (!pskb_may_pull(skb, sizeof(*th)))
goto out;
goto out;
}
+ copy_destructor = gso_skb->destructor == tcp_wfree;
+ ooo_okay = gso_skb->ooo_okay;
+ /* All segments but the first should have ooo_okay cleared */
+ skb->ooo_okay = 0;
+
segs = skb_segment(skb, features);
if (IS_ERR(segs))
goto out;
+ /* Only first segment might have ooo_okay set */
+ segs->ooo_okay = ooo_okay;
+
delta = htonl(oldlen + (thlen + mss));
skb = segs;
thlen, skb->csum));
seq += mss;
+ if (copy_destructor) {
+ skb->destructor = gso_skb->destructor;
+ skb->sk = gso_skb->sk;
+ /* {tcp|sock}_wfree() use exact truesize accounting :
+ * sum(skb->truesize) MUST be exactly be gso_skb->truesize
+ * So we account mss bytes of 'true size' for each segment.
+ * The last segment will contain the remaining.
+ */
+ skb->truesize = mss;
+ gso_skb->truesize -= mss;
+ }
skb = skb->next;
th = tcp_hdr(skb);
* is freed at TX completion, and not right now when gso_skb
* is freed by GSO engine
*/
- if (gso_skb->destructor == tcp_wfree) {
+ if (copy_destructor) {
swap(gso_skb->sk, skb->sk);
swap(gso_skb->destructor, skb->destructor);
swap(gso_skb->truesize, skb->truesize);
for (i = 0; i < shi->nr_frags; ++i) {
const struct skb_frag_struct *f = &shi->frags[i];
- struct page *page = skb_frag_page(f);
- sg_set_page(&sg, page, skb_frag_size(f), f->page_offset);
+ unsigned int offset = f->page_offset;
+ struct page *page = skb_frag_page(f) + (offset >> PAGE_SHIFT);
+
+ sg_set_page(&sg, page, skb_frag_size(f),
+ offset_in_page(offset));
if (crypto_hash_update(desc, &sg, skb_frag_size(f)))
return 1;
}
* tcp_xmit_retransmit_queue().
*/
static void tcp_fastretrans_alert(struct sock *sk, int pkts_acked,
- int prior_sacked, bool is_dupack,
- int flag)
+ int prior_sacked, int prior_packets,
+ bool is_dupack, int flag)
{
struct inet_connection_sock *icsk = inet_csk(sk);
struct tcp_sock *tp = tcp_sk(sk);
tcp_add_reno_sack(sk);
} else
do_lost = tcp_try_undo_partial(sk, pkts_acked);
- newly_acked_sacked = pkts_acked + tp->sacked_out - prior_sacked;
+ newly_acked_sacked = prior_packets - tp->packets_out +
+ tp->sacked_out - prior_sacked;
break;
case TCP_CA_Loss:
tcp_process_loss(sk, flag, is_dupack);
if (is_dupack)
tcp_add_reno_sack(sk);
}
- newly_acked_sacked = pkts_acked + tp->sacked_out - prior_sacked;
+ newly_acked_sacked = prior_packets - tp->packets_out +
+ tp->sacked_out - prior_sacked;
if (icsk->icsk_ca_state <= TCP_CA_Disorder)
tcp_try_undo_dsack(sk);
bool is_dupack = false;
u32 prior_in_flight;
u32 prior_fackets;
- int prior_packets;
+ int prior_packets = tp->packets_out;
int prior_sacked = tp->sacked_out;
int pkts_acked = 0;
+ int previous_packets_out = 0;
/* If the ack is older than previous acks
* then we can probably ignore it.
sk->sk_err_soft = 0;
icsk->icsk_probes_out = 0;
tp->rcv_tstamp = tcp_time_stamp;
- prior_packets = tp->packets_out;
if (!prior_packets)
goto no_queue;
/* See if we can take anything off of the retransmit queue. */
+ previous_packets_out = tp->packets_out;
flag |= tcp_clean_rtx_queue(sk, prior_fackets, prior_snd_una);
- pkts_acked = prior_packets - tp->packets_out;
+ pkts_acked = previous_packets_out - tp->packets_out;
if (tcp_ack_is_dubious(sk, flag)) {
/* Advance CWND, if state allows this. */
tcp_cong_avoid(sk, ack, prior_in_flight);
is_dupack = !(flag & (FLAG_SND_UNA_ADVANCED | FLAG_NOT_DUP));
tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
- is_dupack, flag);
+ prior_packets, is_dupack, flag);
} else {
if (flag & FLAG_DATA_ACKED)
tcp_cong_avoid(sk, ack, prior_in_flight);
/* If data was DSACKed, see if we can undo a cwnd reduction. */
if (flag & FLAG_DSACKING_ACK)
tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
- is_dupack, flag);
+ prior_packets, is_dupack, flag);
/* If this ack opens up a zero window, clear backoff. It was
* being used to time the probes, and is probably far higher than
* it needs to be for normal retransmission.
if (TCP_SKB_CB(skb)->sacked) {
flag |= tcp_sacktag_write_queue(sk, skb, prior_snd_una);
tcp_fastretrans_alert(sk, pkts_acked, prior_sacked,
- is_dupack, flag);
+ prior_packets, is_dupack, flag);
}
SOCK_DEBUG(sk, "Ack %u before %u:%u\n", ack, tp->snd_una, tp->snd_nxt);
&md5);
tcp_header_size = tcp_options_size + sizeof(struct tcphdr);
- if (tcp_packets_in_flight(tp) == 0) {
+ if (tcp_packets_in_flight(tp) == 0)
tcp_ca_event(sk, CA_EVENT_TX_START);
- skb->ooo_okay = 1;
- } else
- skb->ooo_okay = 0;
+
+ /* if no packet is in qdisc/device queue, then allow XPS to select
+ * another queue.
+ */
+ skb->ooo_okay = sk_wmem_alloc_get(sk) == 0;
skb_push(skb, tcp_header_size);
skb_reset_transport_header(skb);
if (WARN_ON(np->cork.opt))
return -EINVAL;
- np->cork.opt = kmalloc(opt->tot_len, sk->sk_allocation);
+ np->cork.opt = kzalloc(opt->tot_len, sk->sk_allocation);
if (unlikely(np->cork.opt == NULL))
return -ENOBUFS;
/*
* We now have some discovery info to deliver!
*/
- discovery = kmalloc(sizeof(discovery_t), GFP_ATOMIC);
+ discovery = kzalloc(sizeof(discovery_t), GFP_ATOMIC);
if (!discovery) {
IRDA_WARNING("%s: unable to malloc!\n", __func__);
return;
void ieee80211_mgd_stop(struct ieee80211_sub_if_data *sdata);
void ieee80211_mgd_conn_tx_status(struct ieee80211_sub_if_data *sdata,
__le16 fc, bool acked);
+void ieee80211_sta_restart(struct ieee80211_sub_if_data *sdata);
/* IBSS code */
void ieee80211_ibss_notify_scan_completed(struct ieee80211_local *local);
static void
ieee80211_sta_process_chanswitch(struct ieee80211_sub_if_data *sdata,
- u64 timestamp, struct ieee802_11_elems *elems)
+ u64 timestamp, struct ieee802_11_elems *elems,
+ bool beacon)
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
struct cfg80211_chan_def new_vht_chandef = {};
const struct ieee80211_sec_chan_offs_ie *sec_chan_offs;
const struct ieee80211_wide_bw_chansw_ie *wide_bw_chansw_ie;
+ const struct ieee80211_ht_operation *ht_oper;
int secondary_channel_offset = -1;
ASSERT_MGD_MTX(ifmgd);
sec_chan_offs = elems->sec_chan_offs;
wide_bw_chansw_ie = elems->wide_bw_chansw_ie;
+ ht_oper = elems->ht_operation;
if (ifmgd->flags & (IEEE80211_STA_DISABLE_HT |
IEEE80211_STA_DISABLE_40MHZ)) {
sec_chan_offs = NULL;
wide_bw_chansw_ie = NULL;
+ /* only used for bandwidth here */
+ ht_oper = NULL;
}
if (ifmgd->flags & IEEE80211_STA_DISABLE_VHT)
return;
}
- if (sec_chan_offs) {
+ if (!beacon && sec_chan_offs) {
secondary_channel_offset = sec_chan_offs->sec_chan_offs;
+ } else if (beacon && ht_oper) {
+ secondary_channel_offset =
+ ht_oper->ht_param & IEEE80211_HT_PARAM_CHA_SEC_OFFSET;
} else if (!(ifmgd->flags & IEEE80211_STA_DISABLE_HT)) {
- /* if HT is enabled and the IE not present, it's still HT */
+ /*
+ * If it's not a beacon, HT is enabled and the IE not present,
+ * it's 20 MHz, 802.11-2012 8.5.2.6:
+ * This element [the Secondary Channel Offset Element] is
+ * present when switching to a 40 MHz channel. It may be
+ * present when switching to a 20 MHz channel (in which
+ * case the secondary channel offset is set to SCN).
+ */
secondary_channel_offset = IEEE80211_HT_PARAM_CHA_SEC_NONE;
}
mutex_unlock(&local->iflist_mtx);
}
- ieee80211_sta_process_chanswitch(sdata, rx_status->mactime, elems);
+ ieee80211_sta_process_chanswitch(sdata, rx_status->mactime,
+ elems, true);
}
ieee80211_sta_process_chanswitch(sdata,
rx_status->mactime,
- &elems);
+ &elems, false);
} else if (mgmt->u.action.category == WLAN_CATEGORY_PUBLIC) {
ies_len = skb->len -
offsetof(struct ieee80211_mgmt,
ieee80211_sta_process_chanswitch(sdata,
rx_status->mactime,
- &elems);
+ &elems, false);
}
break;
}
}
}
+#ifdef CONFIG_PM
+void ieee80211_sta_restart(struct ieee80211_sub_if_data *sdata)
+{
+ struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
+
+ mutex_lock(&ifmgd->mtx);
+ if (!ifmgd->associated) {
+ mutex_unlock(&ifmgd->mtx);
+ return;
+ }
+
+ if (sdata->flags & IEEE80211_SDATA_DISCONNECT_RESUME) {
+ sdata->flags &= ~IEEE80211_SDATA_DISCONNECT_RESUME;
+ mlme_dbg(sdata, "driver requested disconnect after resume\n");
+ ieee80211_sta_connection_lost(sdata,
+ ifmgd->associated->bssid,
+ WLAN_REASON_UNSPECIFIED,
+ true);
+ mutex_unlock(&ifmgd->mtx);
+ return;
+ }
+ mutex_unlock(&ifmgd->mtx);
+}
+#endif
+
/* interface setup */
void ieee80211_sta_setup_sdata(struct ieee80211_sub_if_data *sdata)
{
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
u8 frame_buf[IEEE80211_DEAUTH_FRAME_LEN];
bool tx = !req->local_state_change;
- bool sent_frame = false;
+ bool report_frame = false;
mutex_lock(&ifmgd->mtx);
ieee80211_destroy_auth_data(sdata, false);
mutex_unlock(&ifmgd->mtx);
- sent_frame = tx;
+ report_frame = true;
goto out;
}
ether_addr_equal(ifmgd->associated->bssid, req->bssid)) {
ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
req->reason_code, tx, frame_buf);
- sent_frame = tx;
+ report_frame = true;
}
mutex_unlock(&ifmgd->mtx);
out:
- if (sent_frame)
+ if (report_frame)
__cfg80211_send_deauth(sdata->dev, frame_buf,
IEEE80211_DEAUTH_FRAME_LEN);
struct ieee80211_sta *pubsta,
struct ieee80211_sta_rates *rates)
{
- struct ieee80211_sta_rates *old = rcu_dereference(pubsta->rates);
+ struct ieee80211_sta_rates *old;
+ /*
+ * mac80211 guarantees that this function will not be called
+ * concurrently, so the following RCU access is safe, even without
+ * extra locking. This can not be checked easily, so we just set
+ * the condition to true.
+ */
+ old = rcu_dereference_protected(pubsta->rates, true);
rcu_assign_pointer(pubsta->rates, rates);
if (old)
kfree_rcu(old, rcu_head);
* and location updates. Note that mac80211
* itself never looks at these frames.
*/
+ if (!multicast &&
+ !ether_addr_equal(sdata->vif.addr, hdr->addr1))
+ return 0;
if (ieee80211_is_public_action(hdr, skb->len))
return 1;
if (!ieee80211_is_beacon(hdr->frame_control))
u32 iv32 = get_unaligned_le32(&data[4]);
u16 iv16 = data[2] | (data[0] << 8);
- spin_lock_bh(&key->u.tkip.txlock);
+ spin_lock(&key->u.tkip.txlock);
ieee80211_compute_tkip_p1k(key, iv32);
tkip_mixing_phase2(tk, ctx, iv16, p2k);
- spin_unlock_bh(&key->u.tkip.txlock);
+ spin_unlock(&key->u.tkip.txlock);
}
EXPORT_SYMBOL(ieee80211_get_tkip_p2k);
mb();
local->resuming = false;
+ list_for_each_entry(sdata, &local->interfaces, list) {
+ if (!ieee80211_sdata_running(sdata))
+ continue;
+ if (sdata->vif.type == NL80211_IFTYPE_STATION)
+ ieee80211_sta_restart(sdata);
+ }
+
mod_timer(&local->sta_cleanup, jiffies + 1);
#else
WARN_ON(1);
va_start(args, fmt);
vsnprintf(prefix, sizeof(prefix), fmt, args);
va_end(args);
- logger->logfn(pf, hooknum, skb, in, out, loginfo, prefix);
+ logger->logfn(net, pf, hooknum, skb, in, out, loginfo, prefix);
}
rcu_read_unlock();
}
return 0;
out_sysctl:
+#ifdef CONFIG_PROC_FS
/* For init_net: errors will trigger panic, don't unroll on error. */
if (!net_eq(net, &init_net))
remove_proc_entry("nf_log", net->nf.proc_netfilter);
-
+#endif
return ret;
}
static void __net_exit nf_log_net_exit(struct net *net)
{
netfilter_log_sysctl_exit(net);
+#ifdef CONFIG_PROC_FS
remove_proc_entry("nf_log", net->nf.proc_netfilter);
+#endif
}
static struct pernet_operations nf_log_net_ops = {
/* log handler for internal netfilter logging api */
void
-nfulnl_log_packet(u_int8_t pf,
+nfulnl_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const struct nf_loginfo *li;
unsigned int qthreshold;
unsigned int plen;
- struct net *net = dev_net(in ? in : out);
struct nfnl_log_net *log = nfnl_log_pernet(net);
if (li_user && li_user->type == NF_LOG_TYPE_ULOG)
static void __net_exit nfnl_log_net_exit(struct net *net)
{
+#ifdef CONFIG_PROC_FS
remove_proc_entry("nfnetlink_log", net->nf.proc_netfilter);
+#endif
}
static struct pernet_operations nfnl_log_net_ops = {
static void __net_exit nfnl_queue_net_exit(struct net *net)
{
+#ifdef CONFIG_PROC_FS
remove_proc_entry("nfnetlink_queue", net->nf.proc_netfilter);
+#endif
}
static struct pernet_operations nfnl_queue_net_ops = {
static void
-ipt_log_packet(u_int8_t pf,
+ipt_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const char *prefix)
{
struct sbuff *m;
- struct net *net = dev_net(in ? in : out);
/* FIXME: Disabled from containers until syslog ns is supported */
if (!net_eq(net, &init_net))
}
static void
-ip6t_log_packet(u_int8_t pf,
+ip6t_log_packet(struct net *net,
+ u_int8_t pf,
unsigned int hooknum,
const struct sk_buff *skb,
const struct net_device *in,
const char *prefix)
{
struct sbuff *m;
- struct net *net = dev_net(in ? in : out);
/* FIXME: Disabled from containers until syslog ns is supported */
if (!net_eq(net, &init_net))
{
const struct xt_log_info *loginfo = par->targinfo;
struct nf_loginfo li;
+ struct net *net = dev_net(par->in ? par->in : par->out);
li.type = NF_LOG_TYPE_LOG;
li.u.log.level = loginfo->level;
li.u.log.logflags = loginfo->logflags;
if (par->family == NFPROTO_IPV4)
- ipt_log_packet(NFPROTO_IPV4, par->hooknum, skb, par->in,
+ ipt_log_packet(net, NFPROTO_IPV4, par->hooknum, skb, par->in,
par->out, &li, loginfo->prefix);
#if IS_ENABLED(CONFIG_IP6_NF_IPTABLES)
else if (par->family == NFPROTO_IPV6)
- ip6t_log_packet(NFPROTO_IPV6, par->hooknum, skb, par->in,
+ ip6t_log_packet(net, NFPROTO_IPV6, par->hooknum, skb, par->in,
par->out, &li, loginfo->prefix);
#endif
else
{
const struct xt_nflog_info *info = par->targinfo;
struct nf_loginfo li;
+ struct net *net = dev_net(par->in ? par->in : par->out);
li.type = NF_LOG_TYPE_ULOG;
li.u.ulog.copy_len = info->len;
li.u.ulog.group = info->group;
li.u.ulog.qthreshold = info->threshold;
- nfulnl_log_packet(par->family, par->hooknum, skb, par->in,
+ nfulnl_log_packet(net, par->family, par->hooknum, skb, par->in,
par->out, &li, info->prefix);
return XT_CONTINUE;
}
static unsigned int
tcpoptstrip_mangle_packet(struct sk_buff *skb,
- const struct xt_tcpoptstrip_target_info *info,
+ const struct xt_action_param *par,
unsigned int tcphoff, unsigned int minlen)
{
+ const struct xt_tcpoptstrip_target_info *info = par->targinfo;
unsigned int optl, i, j;
struct tcphdr *tcph;
u_int16_t n, o;
u_int8_t *opt;
+ int len;
+
+ /* This is a fragment, no TCP header is available */
+ if (par->fragoff != 0)
+ return XT_CONTINUE;
if (!skb_make_writable(skb, skb->len))
return NF_DROP;
+ len = skb->len - tcphoff;
+ if (len < (int)sizeof(struct tcphdr) ||
+ tcp_hdr(skb)->doff * 4 > len)
+ return NF_DROP;
+
tcph = (struct tcphdr *)(skb_network_header(skb) + tcphoff);
opt = (u_int8_t *)tcph;
static unsigned int
tcpoptstrip_tg4(struct sk_buff *skb, const struct xt_action_param *par)
{
- return tcpoptstrip_mangle_packet(skb, par->targinfo, ip_hdrlen(skb),
+ return tcpoptstrip_mangle_packet(skb, par, ip_hdrlen(skb),
sizeof(struct iphdr) + sizeof(struct tcphdr));
}
if (tcphoff < 0)
return NF_DROP;
- return tcpoptstrip_mangle_packet(skb, par->targinfo, tcphoff,
+ return tcpoptstrip_mangle_packet(skb, par, tcphoff,
sizeof(*ipv6h) + sizeof(struct tcphdr));
}
#endif
}
}
+/**
+ * netlbl_domhsh_validate - Validate a new domain mapping entry
+ * @entry: the entry to validate
+ *
+ * This function validates the new domain mapping entry to ensure that it is
+ * a valid entry. Returns zero on success, negative values on failure.
+ *
+ */
+static int netlbl_domhsh_validate(const struct netlbl_dom_map *entry)
+{
+ struct netlbl_af4list *iter4;
+ struct netlbl_domaddr4_map *map4;
+#if IS_ENABLED(CONFIG_IPV6)
+ struct netlbl_af6list *iter6;
+ struct netlbl_domaddr6_map *map6;
+#endif /* IPv6 */
+
+ if (entry == NULL)
+ return -EINVAL;
+
+ switch (entry->type) {
+ case NETLBL_NLTYPE_UNLABELED:
+ if (entry->type_def.cipsov4 != NULL ||
+ entry->type_def.addrsel != NULL)
+ return -EINVAL;
+ break;
+ case NETLBL_NLTYPE_CIPSOV4:
+ if (entry->type_def.cipsov4 == NULL)
+ return -EINVAL;
+ break;
+ case NETLBL_NLTYPE_ADDRSELECT:
+ netlbl_af4list_foreach(iter4, &entry->type_def.addrsel->list4) {
+ map4 = netlbl_domhsh_addr4_entry(iter4);
+ switch (map4->type) {
+ case NETLBL_NLTYPE_UNLABELED:
+ if (map4->type_def.cipsov4 != NULL)
+ return -EINVAL;
+ break;
+ case NETLBL_NLTYPE_CIPSOV4:
+ if (map4->type_def.cipsov4 == NULL)
+ return -EINVAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+#if IS_ENABLED(CONFIG_IPV6)
+ netlbl_af6list_foreach(iter6, &entry->type_def.addrsel->list6) {
+ map6 = netlbl_domhsh_addr6_entry(iter6);
+ switch (map6->type) {
+ case NETLBL_NLTYPE_UNLABELED:
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+#endif /* IPv6 */
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
/*
* Domain Hash Table Functions
*/
struct netlbl_af6list *tmp6;
#endif /* IPv6 */
+ ret_val = netlbl_domhsh_validate(entry);
+ if (ret_val != 0)
+ return ret_val;
+
/* XXX - we can remove this RCU read lock as the spinlock protects the
* entire function, but before we do we need to fixup the
* netlbl_af[4,6]list RCU functions to do "the right thing" with
#include <linux/sunrpc/gss_api.h>
#include <asm/uaccess.h>
+#include "../netns.h"
+
static const struct rpc_authops authgss_ops;
static const struct rpc_credops gss_credops;
};
/* pipe_version >= 0 if and only if someone has a pipe open. */
-static int pipe_version = -1;
-static atomic_t pipe_users = ATOMIC_INIT(0);
static DEFINE_SPINLOCK(pipe_version_lock);
static struct rpc_wait_queue pipe_version_rpc_waitqueue;
static DECLARE_WAIT_QUEUE_HEAD(pipe_version_waitqueue);
char databuf[UPCALL_BUF_LEN];
};
-static int get_pipe_version(void)
+static int get_pipe_version(struct net *net)
{
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
int ret;
spin_lock(&pipe_version_lock);
- if (pipe_version >= 0) {
- atomic_inc(&pipe_users);
- ret = pipe_version;
+ if (sn->pipe_version >= 0) {
+ atomic_inc(&sn->pipe_users);
+ ret = sn->pipe_version;
} else
ret = -EAGAIN;
spin_unlock(&pipe_version_lock);
return ret;
}
-static void put_pipe_version(void)
+static void put_pipe_version(struct net *net)
{
- if (atomic_dec_and_lock(&pipe_users, &pipe_version_lock)) {
- pipe_version = -1;
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
+
+ if (atomic_dec_and_lock(&sn->pipe_users, &pipe_version_lock)) {
+ sn->pipe_version = -1;
spin_unlock(&pipe_version_lock);
}
}
static void
gss_release_msg(struct gss_upcall_msg *gss_msg)
{
+ struct net *net = rpc_net_ns(gss_msg->auth->client);
if (!atomic_dec_and_test(&gss_msg->count))
return;
- put_pipe_version();
+ put_pipe_version(net);
BUG_ON(!list_empty(&gss_msg->list));
if (gss_msg->ctx != NULL)
gss_put_ctx(gss_msg->ctx);
struct rpc_clnt *clnt,
const char *service_name)
{
- if (pipe_version == 0)
+ struct net *net = rpc_net_ns(clnt);
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
+
+ if (sn->pipe_version == 0)
gss_encode_v0_msg(gss_msg);
else /* pipe_version == 1 */
gss_encode_v1_msg(gss_msg, clnt, service_name);
gss_msg = kzalloc(sizeof(*gss_msg), GFP_NOFS);
if (gss_msg == NULL)
return ERR_PTR(-ENOMEM);
- vers = get_pipe_version();
+ vers = get_pipe_version(rpc_net_ns(clnt));
if (vers < 0) {
kfree(gss_msg);
return ERR_PTR(vers);
static inline int
gss_create_upcall(struct gss_auth *gss_auth, struct gss_cred *gss_cred)
{
+ struct net *net = rpc_net_ns(gss_auth->client);
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
struct rpc_pipe *pipe;
struct rpc_cred *cred = &gss_cred->gc_base;
struct gss_upcall_msg *gss_msg;
+ unsigned long timeout;
DEFINE_WAIT(wait);
- int err = 0;
+ int err;
dprintk("RPC: %s for uid %u\n",
__func__, from_kuid(&init_user_ns, cred->cr_uid));
retry:
+ err = 0;
+ /* Default timeout is 15s unless we know that gssd is not running */
+ timeout = 15 * HZ;
+ if (!sn->gssd_running)
+ timeout = HZ >> 2;
gss_msg = gss_setup_upcall(gss_auth->client, gss_auth, cred);
if (PTR_ERR(gss_msg) == -EAGAIN) {
err = wait_event_interruptible_timeout(pipe_version_waitqueue,
- pipe_version >= 0, 15*HZ);
- if (pipe_version < 0) {
+ sn->pipe_version >= 0, timeout);
+ if (sn->pipe_version < 0) {
+ if (err == 0)
+ sn->gssd_running = 0;
warn_gssd();
err = -EACCES;
}
- if (err)
+ if (err < 0)
goto out;
goto retry;
}
static int gss_pipe_open(struct inode *inode, int new_version)
{
+ struct net *net = inode->i_sb->s_fs_info;
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
int ret = 0;
spin_lock(&pipe_version_lock);
- if (pipe_version < 0) {
+ if (sn->pipe_version < 0) {
/* First open of any gss pipe determines the version: */
- pipe_version = new_version;
+ sn->pipe_version = new_version;
rpc_wake_up(&pipe_version_rpc_waitqueue);
wake_up(&pipe_version_waitqueue);
- } else if (pipe_version != new_version) {
+ } else if (sn->pipe_version != new_version) {
/* Trying to open a pipe of a different version */
ret = -EBUSY;
goto out;
}
- atomic_inc(&pipe_users);
+ atomic_inc(&sn->pipe_users);
out:
spin_unlock(&pipe_version_lock);
return ret;
static void
gss_pipe_release(struct inode *inode)
{
+ struct net *net = inode->i_sb->s_fs_info;
struct rpc_pipe *pipe = RPC_I(inode)->pipe;
struct gss_upcall_msg *gss_msg;
}
spin_unlock(&pipe->lock);
- put_pipe_version();
+ put_pipe_version(net);
}
static void
wait_queue_head_t gssp_wq;
struct rpc_clnt *gssp_clnt;
int use_gss_proxy;
+ int pipe_version;
+ atomic_t pipe_users;
struct proc_dir_entry *use_gssp_proc;
+
+ unsigned int gssd_running;
};
extern int sunrpc_net_id;
static int
rpc_pipe_open(struct inode *inode, struct file *filp)
{
+ struct net *net = inode->i_sb->s_fs_info;
+ struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
struct rpc_pipe *pipe;
int first_open;
int res = -ENXIO;
mutex_lock(&inode->i_mutex);
+ sn->gssd_running = 1;
pipe = RPC_I(inode)->pipe;
if (pipe == NULL)
goto out;
struct sunrpc_net *sn = net_generic(net, sunrpc_net_id);
mutex_init(&sn->pipefs_sb_lock);
+ sn->gssd_running = 1;
+ sn->pipe_version = -1;
}
/*
* Note: If the task is ASYNC, and is being made runnable after sitting on an
* rpc_wait_queue, this must be called with the queue spinlock held to protect
* the wait queue operation.
+ * Note the ordering of rpc_test_and_set_running() and rpc_clear_queued(),
+ * which is needed to ensure that __rpc_execute() doesn't loop (due to the
+ * lockless RPC_IS_QUEUED() test) before we've had a chance to test
+ * the RPC_TASK_RUNNING flag.
*/
static void rpc_make_runnable(struct rpc_task *task)
{
+ bool need_wakeup = !rpc_test_and_set_running(task);
+
rpc_clear_queued(task);
- if (rpc_test_and_set_running(task))
+ if (!need_wakeup)
return;
if (RPC_IS_ASYNC(task)) {
INIT_WORK(&task->u.tk_work, rpc_async_schedule);
* cfg80211_mutex lock
*/
res = rfkill_register(rdev->rfkill);
- if (res)
- goto out_rm_dev;
+ if (res) {
+ device_del(&rdev->wiphy.dev);
+
+ mutex_lock(&cfg80211_mutex);
+ debugfs_remove_recursive(rdev->wiphy.debugfsdir);
+ list_del_rcu(&rdev->list);
+ wiphy_regulatory_deregister(wiphy);
+ mutex_unlock(&cfg80211_mutex);
+ return res;
+ }
rtnl_lock();
rdev->wiphy.registered = true;
rtnl_unlock();
return 0;
-
-out_rm_dev:
- device_del(&rdev->wiphy.dev);
- return res;
}
EXPORT_SYMBOL(wiphy_register);
#endif
__cfg80211_disconnect(rdev, dev,
WLAN_REASON_DEAUTH_LEAVING, true);
- cfg80211_mlme_down(rdev, dev);
wdev_unlock(wdev);
break;
case NL80211_IFTYPE_MESH_POINT:
&tcp->payload_tok))
return -ENOBUFS;
+ nla_nest_end(msg, nl_tcp);
+
return 0;
}
if (nla_put_u32(msg, NL80211_ATTR_WIPHY, rdev->wiphy_idx) ||
(netdev && nla_put_u32(msg, NL80211_ATTR_IFINDEX,
netdev->ifindex)) ||
+ nla_put_u64(msg, NL80211_ATTR_WDEV, wdev_id(wdev)) ||
nla_put_u32(msg, NL80211_ATTR_WIPHY_FREQ, freq) ||
(sig_dbm &&
nla_put_u32(msg, NL80211_ATTR_RX_SIGNAL_DBM, sig_dbm)) ||
if (nla_put_u32(msg, NL80211_ATTR_WIPHY, rdev->wiphy_idx) ||
(netdev && nla_put_u32(msg, NL80211_ATTR_IFINDEX,
netdev->ifindex)) ||
+ nla_put_u64(msg, NL80211_ATTR_WDEV, wdev_id(wdev)) ||
nla_put(msg, NL80211_ATTR_FRAME, len, buf) ||
nla_put_u64(msg, NL80211_ATTR_COOKIE, cookie) ||
(ack && nla_put_flag(msg, NL80211_ATTR_ACK)))
/* was it connected by userspace SME? */
if (!wdev->conn) {
cfg80211_mlme_down(rdev, dev);
- return 0;
+ goto disconnect;
}
if (wdev->sme_state == CFG80211_SME_CONNECTING &&
return err;
}
+ disconnect:
if (wdev->sme_state == CFG80211_SME_CONNECTED)
__cfg80211_disconnected(dev, NULL, 0, 0, false);
else if (wdev->sme_state == CFG80211_SME_CONNECTING)
TP_STRUCT__entry(
WIPHY_ENTRY
WDEV_ENTRY
+ __field(bool, non_wireless)
__field(bool, disconnect)
__field(bool, magic_pkt)
__field(bool, gtk_rekey_failure)
__field(bool, rfkill_release)
__field(s32, pattern_idx)
__field(u32, packet_len)
- __dynamic_array(u8, packet, wakeup->packet_present_len)
+ __dynamic_array(u8, packet,
+ wakeup ? wakeup->packet_present_len : 0)
),
TP_fast_assign(
WIPHY_ASSIGN;
WDEV_ASSIGN;
- __entry->disconnect = wakeup->disconnect;
- __entry->magic_pkt = wakeup->magic_pkt;
- __entry->gtk_rekey_failure = wakeup->gtk_rekey_failure;
- __entry->eap_identity_req = wakeup->eap_identity_req;
- __entry->four_way_handshake = wakeup->four_way_handshake;
- __entry->rfkill_release = wakeup->rfkill_release;
- __entry->pattern_idx = wakeup->pattern_idx;
- __entry->packet_len = wakeup->packet_len;
- if (wakeup->packet && wakeup->packet_present_len)
+ __entry->non_wireless = !wakeup;
+ __entry->disconnect = wakeup ? wakeup->disconnect : false;
+ __entry->magic_pkt = wakeup ? wakeup->magic_pkt : false;
+ __entry->gtk_rekey_failure = wakeup ? wakeup->gtk_rekey_failure : false;
+ __entry->eap_identity_req = wakeup ? wakeup->eap_identity_req : false;
+ __entry->four_way_handshake = wakeup ? wakeup->four_way_handshake : false;
+ __entry->rfkill_release = wakeup ? wakeup->rfkill_release : false;
+ __entry->pattern_idx = wakeup ? wakeup->pattern_idx : false;
+ __entry->packet_len = wakeup ? wakeup->packet_len : false;
+ if (wakeup && wakeup->packet && wakeup->packet_present_len)
memcpy(__get_dynamic_array(packet), wakeup->packet,
wakeup->packet_present_len);
),
if (unlikely(x->km.state != XFRM_STATE_VALID)) {
XFRM_INC_STATS(net, LINUX_MIB_XFRMOUTSTATEINVALID);
+ err = -EINVAL;
goto error;
}
def get_kallsyms_table():
global kallsyms
+
try:
f = open("/proc/kallsyms", "r")
- linecount = 0
- for line in f:
- linecount = linecount+1
- f.seek(0)
except:
return
-
- j = 0
for line in f:
loc = int(line.split()[0], 16)
name = line.split()[2]
- j = j +1
- if ((j % 100) == 0):
- print "\r" + str(j) + "/" + str(linecount),
- kallsyms.append({ 'loc': loc, 'name' : name})
-
- print "\r" + str(j) + "/" + str(linecount)
+ kallsyms.append((loc, name))
kallsyms.sort()
- return
def get_sym(sloc):
loc = int(sloc)
- for i in kallsyms:
- if (i['loc'] >= loc):
- return (i['name'], i['loc']-loc)
- return (None, 0)
+
+ # Invariant: kallsyms[i][0] <= loc for all 0 <= i <= start
+ # kallsyms[i][0] > loc for all end <= i < len(kallsyms)
+ start, end = -1, len(kallsyms)
+ while end != start + 1:
+ pivot = (start + end) // 2
+ if loc < kallsyms[pivot][0]:
+ end = pivot
+ else:
+ start = pivot
+
+ # Now (start == -1 or kallsyms[start][0] <= loc)
+ # and (start == len(kallsyms) - 1 or loc < kallsyms[start + 1][0])
+ if start >= 0:
+ symloc, name = kallsyms[start]
+ return (name, loc - symloc)
+ else:
+ return (None, 0)
def print_drop_table():
print "%25s %25s %25s" % ("LOCATION", "OFFSET", "COUNT")
# called from perf, when it finds a correspoinding event
def skb__kfree_skb(name, context, cpu, sec, nsec, pid, comm,
- skbaddr, protocol, location):
+ skbaddr, location, protocol):
slocation = str(location)
try:
drop_log[slocation] = drop_log[slocation] + 1
TARGETS += mqueue
TARGETS += net
TARGETS += ptrace
-TARGETS += soft-dirty
TARGETS += vm
all:
+++ /dev/null
-CFLAGS += -iquote../../../../include/uapi -Wall
-soft-dirty: soft-dirty.c
-
-all: soft-dirty
-
-clean:
- rm -f soft-dirty
-
-run_tests: all
- @./soft-dirty || echo "soft-dirty selftests: [FAIL]"
+++ /dev/null
-#include <stdlib.h>
-#include <stdio.h>
-#include <sys/mman.h>
-#include <unistd.h>
-#include <fcntl.h>
-#include <sys/types.h>
-
-typedef unsigned long long u64;
-
-#define PME_PRESENT (1ULL << 63)
-#define PME_SOFT_DIRTY (1Ull << 55)
-
-#define PAGES_TO_TEST 3
-#ifndef PAGE_SIZE
-#define PAGE_SIZE 4096
-#endif
-
-static void get_pagemap2(char *mem, u64 *map)
-{
- int fd;
-
- fd = open("/proc/self/pagemap2", O_RDONLY);
- if (fd < 0) {
- perror("Can't open pagemap2");
- exit(1);
- }
-
- lseek(fd, (unsigned long)mem / PAGE_SIZE * sizeof(u64), SEEK_SET);
- read(fd, map, sizeof(u64) * PAGES_TO_TEST);
- close(fd);
-}
-
-static inline char map_p(u64 map)
-{
- return map & PME_PRESENT ? 'p' : '-';
-}
-
-static inline char map_sd(u64 map)
-{
- return map & PME_SOFT_DIRTY ? 'd' : '-';
-}
-
-static int check_pte(int step, int page, u64 *map, u64 want)
-{
- if ((map[page] & want) != want) {
- printf("Step %d Page %d has %c%c, want %c%c\n",
- step, page,
- map_p(map[page]), map_sd(map[page]),
- map_p(want), map_sd(want));
- return 1;
- }
-
- return 0;
-}
-
-static void clear_refs(void)
-{
- int fd;
- char *v = "4";
-
- fd = open("/proc/self/clear_refs", O_WRONLY);
- if (write(fd, v, 3) < 3) {
- perror("Can't clear soft-dirty bit");
- exit(1);
- }
- close(fd);
-}
-
-int main(void)
-{
- char *mem, x;
- u64 map[PAGES_TO_TEST];
-
- mem = mmap(NULL, PAGES_TO_TEST * PAGE_SIZE,
- PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANON, 0, 0);
-
- x = mem[0];
- mem[2 * PAGE_SIZE] = 'c';
- get_pagemap2(mem, map);
-
- if (check_pte(1, 0, map, PME_PRESENT))
- return 1;
- if (check_pte(1, 1, map, 0))
- return 1;
- if (check_pte(1, 2, map, PME_PRESENT | PME_SOFT_DIRTY))
- return 1;
-
- clear_refs();
- get_pagemap2(mem, map);
-
- if (check_pte(2, 0, map, PME_PRESENT))
- return 1;
- if (check_pte(2, 1, map, 0))
- return 1;
- if (check_pte(2, 2, map, PME_PRESENT))
- return 1;
-
- mem[0] = 'a';
- mem[PAGE_SIZE] = 'b';
- x = mem[2 * PAGE_SIZE];
- get_pagemap2(mem, map);
-
- if (check_pte(3, 0, map, PME_PRESENT | PME_SOFT_DIRTY))
- return 1;
- if (check_pte(3, 1, map, PME_PRESENT | PME_SOFT_DIRTY))
- return 1;
- if (check_pte(3, 2, map, PME_PRESENT))
- return 1;
-
- (void)x; /* gcc warn */
-
- printf("PASS\n");
- return 0;
-}
projects / firefly-linux-kernel-4.4.55.git / commitdiff