NS16550A: Restore HS settings in EXCR2 on resume
authorDavid Woodhouse <dwmw2@infradead.org>
Thu, 17 May 2007 06:27:39 +0000 (14:27 +0800)
committerLinus Torvalds <torvalds@woody.linux-foundation.org>
Thu, 17 May 2007 12:25:49 +0000 (05:25 -0700)
After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.

This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.

It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/serial/8250.c

index 48e259a0167d180c1f212d3d0f723133dc5ff797..c84dab083a852b48ff7a55d1fbe87c79cd01e23a 100644 (file)
@@ -894,7 +894,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
                        quot = serial_dl_read(up);
                        quot <<= 3;
 
-                       status1 = serial_in(up, 0x04); /* EXCR1 */
+                       status1 = serial_in(up, 0x04); /* EXCR2 */
                        status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
                        status1 |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
                        serial_outp(up, 0x04, status1);
@@ -2617,7 +2617,22 @@ void serial8250_suspend_port(int line)
  */
 void serial8250_resume_port(int line)
 {
-       uart_resume_port(&serial8250_reg, &serial8250_ports[line].port);
+       struct uart_8250_port *up = &serial8250_ports[line];
+
+       if (up->capabilities & UART_NATSEMI) {
+               unsigned char tmp;
+
+               /* Ensure it's still in high speed mode */
+               serial_outp(up, UART_LCR, 0xE0);
+
+               tmp = serial_in(up, 0x04); /* EXCR2 */
+               tmp &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
+               tmp |= 0x10;  /* 1.625 divisor for baud_base --> 921600 */
+               serial_outp(up, 0x04, tmp);
+
+               serial_outp(up, UART_LCR, 0);
+       }
+       uart_resume_port(&serial8250_reg, &up->port);
 }
 
 /*
@@ -2694,7 +2709,7 @@ static int serial8250_resume(struct platform_device *dev)
                struct uart_8250_port *up = &serial8250_ports[i];
 
                if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
-                       uart_resume_port(&serial8250_reg, &up->port);
+                       serial8250_resume_port(i);
        }
 
        return 0;