Optional properties:
- reset-gpio: gpio pin number of power good signal
+- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
+ specify this property, to keep backwards compatibility a range of 0x00-0xff
+ is assumed if not present)
NVIDIA Tegra PCIe controller
Required properties:
-- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie"
+- compatible: Must be one of:
+ - "nvidia,tegra20-pcie"
+ - "nvidia,tegra30-pcie"
+ - "nvidia,tegra124-pcie"
- device_type: Must be "pci"
- reg: A list of physical base address and length for each set of controller
registers. Must contain an entry for each entry in the reg-names property.
- afi
- pcie_x
+Required properties on Tegra124 and later:
+- phys: Must contain an entry for each entry in phy-names.
+- phy-names: Must include the following entries:
+ - pcie
+
Power supplies for Tegra20:
- avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
- vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
- avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
- vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+Power supplies for Tegra124:
+- Required:
+ - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
+ - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+ - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
+ supply 1.05 V.
+ - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
+ Must supply 3.3 V.
+ - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
+ Must supply 3.3 V.
+ - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
+ supply 2.8-3.3 V.
+ - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
+ supply 1.05 V.
+
Root ports are defined as subnodes of the PCIe controller node.
Required properties:
--- /dev/null
+TI Keystone PCIe interface
+
+Keystone PCI host Controller is based on Designware PCI h/w version 3.65.
+It shares common functions with PCIe Designware core driver and inherit
+common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt
+
+Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt
+for the details of Designware DT bindings. Additional properties are
+described here as well as properties that are not applicable.
+
+Required Properties:-
+
+compatibility: "ti,keystone-pcie"
+reg: index 1 is the base address and length of DW application registers.
+ index 2 is the base address and length of PCI device ID register.
+
+pcie_msi_intc : Interrupt controller device node for MSI IRQ chip
+ interrupt-cells: should be set to 1
+ interrupt-parent: Parent interrupt controller phandle
+ interrupts: GIC interrupt lines connected to PCI MSI interrupt lines
+
+ Example:
+ pcie_msi_intc: msi-interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>;
+ };
+
+pcie_intc: Interrupt controller device node for Legacy IRQ chip
+ interrupt-cells: should be set to 1
+ interrupt-parent: Parent interrupt controller phandle
+ interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines
+
+ Example:
+ pcie_intc: legacy-interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
+ };
+
+Optional properties:-
+ phys: phandle to Generic Keystone SerDes phy for PCI
+ phy-names: name of the Generic Keystine SerDes phy for PCI
+ - If boot loader already does PCI link establishment, then phys and
+ phy-names shouldn't be present.
+
+Designware DT Properties not applicable for Keystone PCI
+
+1. pcie_bus clock-names not used. Instead, a phandle to phys is used.
+
--- /dev/null
+* Xilinx AXI PCIe Root Port Bridge DT description
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- compatible: Should contain "xlnx,axi-pcie-host-1.00.a"
+- reg: Should contain AXI PCIe registers location and length
+- device_type: must be "pci"
+- interrupts: Should contain AXI PCIe interrupt
+- interrupt-map-mask,
+ interrupt-map: standard PCI properties to define the mapping of the
+ PCI interface to interrupt numbers.
+- ranges: ranges for the PCI memory regions (I/O space region is not
+ supported by hardware)
+ Please refer to the standard PCI bus binding document for a more
+ detailed explanation
+
+Optional properties:
+- bus-range: PCI bus numbers covered
+
+Interrupt controller child node
++++++++++++++++++++++++++++++++
+Required properties:
+- interrupt-controller: identifies the node as an interrupt controller
+- #address-cells: specifies the number of cells needed to encode an
+ address. The value must be 0.
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+
+NOTE:
+The core provides a single interrupt for both INTx/MSI messages. So,
+created a interrupt controller node to support 'interrupt-map' DT
+functionality. The driver will create an IRQ domain for this map, decode
+the four INTx interrupts in ISR and route them to this domain.
+
+
+Example:
+++++++++
+
+ pci_express: axi-pcie@50000000 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ compatible = "xlnx,axi-pcie-host-1.00.a";
+ reg = < 0x50000000 0x10000000 >;
+ device_type = "pci";
+ interrupts = < 0 52 4 >;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie_intc 1>,
+ <0 0 0 2 &pcie_intc 2>,
+ <0 0 0 3 &pcie_intc 3>,
+ <0 0 0 4 &pcie_intc 4>;
+ ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >;
+
+ pcie_intc: interrupt-controller {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ }
+ };
IO region
devm_release_mem_region()
devm_release_region()
+ devm_release_resource()
devm_request_mem_region()
devm_request_region()
+ devm_request_resource()
IOMAP
devm_ioport_map()
PCI DRIVER FOR IMX6
M: Richard Zhu <r65037@freescale.com>
-M: Shawn Guo <shawn.guo@freescale.com>
+M: Lucas Stach <l.stach@pengutronix.de>
L: linux-pci@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: drivers/pci/host/*imx6*
+PCI DRIVER FOR TI KEYSTONE
+M: Murali Karicheri <m-karicheri2@ti.com>
+L: linux-pci@vger.kernel.org
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: drivers/pci/host/*keystone*
+
PCI DRIVER FOR MVEBU (Marvell Armada 370 and Armada XP SOC support)
M: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
M: Jason Cooper <jason@lakedaemon.net>
pcie0: pcie@b1000000 {
compatible = "st,spear1340-pcie", "snps,dw-pcie";
- reg = <0xb1000000 0x4000>;
+ reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
+ reg-names = "dbi", "config";
interrupts = <0 68 0x4>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0x0 0 &gic 0 68 0x4>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
- ranges = <0x00000800 0 0x80000000 0x80000000 0 0x00020000 /* configuration space */
- 0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */
+ ranges = <0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
status = "disabled";
};
pcie1: pcie@b1800000 {
compatible = "st,spear1340-pcie", "snps,dw-pcie";
- reg = <0xb1800000 0x4000>;
+ reg = <0xb1800000 0x4000>, <0x90000000 0x20000>;
+ reg-names = "dbi", "config";
interrupts = <0 69 0x4>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0x0 0 &gic 0 69 0x4>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
- ranges = <0x00000800 0 0x90000000 0x90000000 0 0x00020000 /* configuration space */
- 0x81000000 0 0 0x90020000 0 0x00010000 /* downstream I/O */
+ ranges = <0x81000000 0 0 0x90020000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x90030000 0x90030000 0 0x0ffd0000>; /* non-prefetchable memory */
status = "disabled";
};
pcie2: pcie@b4000000 {
compatible = "st,spear1340-pcie", "snps,dw-pcie";
- reg = <0xb4000000 0x4000>;
+ reg = <0xb4000000 0x4000>, <0xc0000000 0x20000>;
+ reg-names = "dbi", "config";
interrupts = <0 70 0x4>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0x0 0 &gic 0 70 0x4>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
- ranges = <0x00000800 0 0xc0000000 0xc0000000 0 0x00020000 /* configuration space */
- 0x81000000 0 0 0xc0020000 0 0x00010000 /* downstream I/O */
+ ranges = <0x81000000 0 0 0xc0020000 0 0x00010000 /* downstream I/O */
0x82000000 0 0xc0030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
status = "disabled";
};
pcie0: pcie@b1000000 {
compatible = "st,spear1340-pcie", "snps,dw-pcie";
- reg = <0xb1000000 0x4000>;
+ reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
+ reg-names = "dbi", "config";
interrupts = <0 68 0x4>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0x0 0 &gic 0 68 0x4>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
- ranges = <0x00000800 0 0x80000000 0x80000000 0 0x00020000 /* configuration space */
- 0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */
+ ranges = <0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
status = "disabled";
};
*/
DEFINE_RAW_SPINLOCK(pci_config_lock);
-static int can_skip_ioresource_align(const struct dmi_system_id *d)
+static int __init can_skip_ioresource_align(const struct dmi_system_id *d)
{
pci_probe |= PCI_CAN_SKIP_ISA_ALIGN;
printk(KERN_INFO "PCI: %s detected, can skip ISA alignment\n", d->ident);
return 0;
}
-static const struct dmi_system_id can_skip_pciprobe_dmi_table[] = {
+static const struct dmi_system_id can_skip_pciprobe_dmi_table[] __initconst = {
/*
* Systems where PCI IO resource ISA alignment can be skipped
* when the ISA enable bit in the bridge control is not set
* on the kernel command line (which was parsed earlier).
*/
-static int set_bf_sort(const struct dmi_system_id *d)
+static int __init set_bf_sort(const struct dmi_system_id *d)
{
if (pci_bf_sort == pci_bf_sort_default) {
pci_bf_sort = pci_dmi_bf;
return 0;
}
-static void read_dmi_type_b1(const struct dmi_header *dm,
- void *private_data)
+static void __init read_dmi_type_b1(const struct dmi_header *dm,
+ void *private_data)
{
u8 *d = (u8 *)dm + 4;
}
}
-static int find_sort_method(const struct dmi_system_id *d)
+static int __init find_sort_method(const struct dmi_system_id *d)
{
dmi_walk(read_dmi_type_b1, NULL);
* Enable renumbering of PCI bus# ranges to reach all PCI busses (Cardbus)
*/
#ifdef __i386__
-static int assign_all_busses(const struct dmi_system_id *d)
+static int __init assign_all_busses(const struct dmi_system_id *d)
{
pci_probe |= PCI_ASSIGN_ALL_BUSSES;
printk(KERN_INFO "%s detected: enabling PCI bus# renumbering"
}
#endif
-static int set_scan_all(const struct dmi_system_id *d)
+static int __init set_scan_all(const struct dmi_system_id *d)
{
printk(KERN_INFO "PCI: %s detected, enabling pci=pcie_scan_all\n",
d->ident);
return 0;
}
-static const struct dmi_system_id pciprobe_dmi_table[] = {
+static const struct dmi_system_id pciprobe_dmi_table[] __initconst = {
#ifdef __i386__
/*
* Laptops which need pci=assign-busses to see Cardbus cards
return 0;
}
-char * __init pcibios_setup(char *str)
+char *__init pcibios_setup(char *str)
{
if (!strcmp(str, "off")) {
pci_probe = 0;
LIST_HEAD(pci_mmcfg_list);
-static __init void pci_mmconfig_remove(struct pci_mmcfg_region *cfg)
+static void __init pci_mmconfig_remove(struct pci_mmcfg_region *cfg)
{
if (cfg->res.parent)
release_resource(&cfg->res);
kfree(cfg);
}
-static __init void free_all_mmcfg(void)
+static void __init free_all_mmcfg(void)
{
struct pci_mmcfg_region *cfg, *tmp;
return new;
}
-static __init struct pci_mmcfg_region *pci_mmconfig_add(int segment, int start,
+static struct pci_mmcfg_region *__init pci_mmconfig_add(int segment, int start,
int end, u64 addr)
{
struct pci_mmcfg_region *new;
return NULL;
}
-static const char __init *pci_mmcfg_e7520(void)
+static const char *__init pci_mmcfg_e7520(void)
{
u32 win;
raw_pci_ops->read(0, 0, PCI_DEVFN(0, 0), 0xce, 2, &win);
return "Intel Corporation E7520 Memory Controller Hub";
}
-static const char __init *pci_mmcfg_intel_945(void)
+static const char *__init pci_mmcfg_intel_945(void)
{
u32 pciexbar, mask = 0, len = 0;
return "Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub";
}
-static const char __init *pci_mmcfg_amd_fam10h(void)
+static const char *__init pci_mmcfg_amd_fam10h(void)
{
u32 low, high, address;
u64 base, msr;
}
static bool __initdata mcp55_checked;
-static const char __init *pci_mmcfg_nvidia_mcp55(void)
+static const char *__init pci_mmcfg_nvidia_mcp55(void)
{
int bus;
int mcp55_mmconf_found = 0;
- static const u32 extcfg_regnum = 0x90;
- static const u32 extcfg_regsize = 4;
- static const u32 extcfg_enable_mask = 1<<31;
- static const u32 extcfg_start_mask = 0xff<<16;
- static const int extcfg_start_shift = 16;
- static const u32 extcfg_size_mask = 0x3<<28;
- static const int extcfg_size_shift = 28;
- static const int extcfg_sizebus[] = {0x100, 0x80, 0x40, 0x20};
- static const u32 extcfg_base_mask[] = {0x7ff8, 0x7ffc, 0x7ffe, 0x7fff};
- static const int extcfg_base_lshift = 25;
+ static const u32 extcfg_regnum __initconst = 0x90;
+ static const u32 extcfg_regsize __initconst = 4;
+ static const u32 extcfg_enable_mask __initconst = 1 << 31;
+ static const u32 extcfg_start_mask __initconst = 0xff << 16;
+ static const int extcfg_start_shift __initconst = 16;
+ static const u32 extcfg_size_mask __initconst = 0x3 << 28;
+ static const int extcfg_size_shift __initconst = 28;
+ static const int extcfg_sizebus[] __initconst = {
+ 0x100, 0x80, 0x40, 0x20
+ };
+ static const u32 extcfg_base_mask[] __initconst = {
+ 0x7ff8, 0x7ffc, 0x7ffe, 0x7fff
+ };
+ static const int extcfg_base_lshift __initconst = 25;
/*
* do check if amd fam10h already took over
const char *(*probe)(void);
};
-static struct pci_mmcfg_hostbridge_probe pci_mmcfg_probes[] __initdata = {
+static const struct pci_mmcfg_hostbridge_probe pci_mmcfg_probes[] __initconst = {
{ 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_E7520_MCH, pci_mmcfg_e7520 },
{ 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID_INTEL,
static struct {
unsigned long address;
unsigned short segment;
-} bios32_indirect = { 0, __KERNEL_CS };
+} bios32_indirect __initdata = { 0, __KERNEL_CS };
/*
* Returns the entry point for the given service, NULL on error
*/
-static unsigned long bios32_service(unsigned long service)
+static unsigned long __init bios32_service(unsigned long service)
{
unsigned char return_code; /* %al */
unsigned long address; /* %ebx */
static int pci_bios_present;
-static int check_pcibios(void)
+static int __init check_pcibios(void)
{
u32 signature, eax, ebx, ecx;
u8 status, major_ver, minor_ver, hw_mech;
* Try to find PCI BIOS.
*/
-static const struct pci_raw_ops *pci_find_bios(void)
+static const struct pci_raw_ops *__init pci_find_bios(void)
{
union bios32 *check;
unsigned char sum;
/*
* PCI device IDs.
*/
-#define PCI_VENDOR_ID_VMWARE 0x15AD
#define PCI_DEVICE_ID_VMWARE_SVGA2 0x0405
/*
#include "vmci_driver.h"
#include "vmci_event.h"
-#define PCI_VENDOR_ID_VMWARE 0x15AD
#define PCI_DEVICE_ID_VMWARE_VMCI 0x0740
#define VMCI_UTIL_NUM_RESOURCES 1
/*
* PCI vendor and device IDs.
*/
-#define PCI_VENDOR_ID_VMWARE 0x15AD
#define PCI_DEVICE_ID_VMWARE_VMXNET3 0x07B0
#define MAX_ETHERNET_CARDS 10
#define MAX_PCI_PASSTHRU_DEVICE 6
help
Say Y here if you want PCIe support on SPEAr13XX SoCs.
+
+config PCI_KEYSTONE
+ bool "TI Keystone PCIe controller"
+ depends on ARCH_KEYSTONE
+ select PCIE_DW
+ select PCIEPORTBUS
+ help
+ Say Y here if you want to enable PCI controller support on Keystone
+ SoCs. The PCI controller on Keystone is based on Designware hardware
+ and therefore the driver re-uses the Designware core functions to
+ implement the driver.
+
+config PCIE_XILINX
+ bool "Xilinx AXI PCIe host bridge support"
+ depends on ARCH_ZYNQ
+ help
+ Say 'Y' here if you want kernel to support the Xilinx AXI PCIe
+ Host Bridge driver.
+
endmenu
obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o
obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
obj-$(CONFIG_PCIE_SPEAR13XX) += pcie-spear13xx.o
+obj-$(CONFIG_PCI_KEYSTONE) += pci-keystone-dw.o pci-keystone.o
+obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
/* PCIe Port Logic registers (memory-mapped) */
#define PL_OFFSET 0x700
+#define PCIE_PL_PFLR (PL_OFFSET + 0x08)
+#define PCIE_PL_PFLR_LINK_STATE_MASK (0x3f << 16)
+#define PCIE_PL_PFLR_FORCE_LINK (1 << 15)
#define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28)
#define PCIE_PHY_DEBUG_R1 (PL_OFFSET + 0x2c)
#define PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING (1 << 29)
static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
{
struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+ u32 val, gpr1, gpr12;
+
+ /*
+ * If the bootloader already enabled the link we need some special
+ * handling to get the core back into a state where it is safe to
+ * touch it for configuration. As there is no dedicated reset signal
+ * wired up for MX6QDL, we need to manually force LTSSM into "detect"
+ * state before completely disabling LTSSM, which is a prerequisite
+ * for core configuration.
+ *
+ * If both LTSSM_ENABLE and REF_SSP_ENABLE are active we have a strong
+ * indication that the bootloader activated the link.
+ */
+ regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1, &gpr1);
+ regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, &gpr12);
+
+ if ((gpr1 & IMX6Q_GPR1_PCIE_REF_CLK_EN) &&
+ (gpr12 & IMX6Q_GPR12_PCIE_CTL_2)) {
+ val = readl(pp->dbi_base + PCIE_PL_PFLR);
+ val &= ~PCIE_PL_PFLR_LINK_STATE_MASK;
+ val |= PCIE_PL_PFLR_FORCE_LINK;
+ writel(val, pp->dbi_base + PCIE_PL_PFLR);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
+ }
regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
IMX6Q_GPR1_PCIE_TEST_PD, 1 << 18);
struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
int ret;
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
- IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
- IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
-
ret = clk_prepare_enable(imx6_pcie->pcie_phy);
if (ret) {
dev_err(pp->dev, "unable to enable pcie_phy clock\n");
/* allow the clocks to stabilize */
usleep_range(200, 500);
+ /* power up core phy and enable ref clock */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
+
/* Some boards don't have PCIe reset GPIO. */
if (gpio_is_valid(imx6_pcie->reset_gpio)) {
gpio_set_value(imx6_pcie->reset_gpio, 0);
return 0;
}
+static void imx6_pcie_shutdown(struct platform_device *pdev)
+{
+ struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev);
+
+ /* bring down link, so bootloader gets clean state in case of reboot */
+ imx6_pcie_assert_core_reset(&imx6_pcie->pp);
+}
+
static const struct of_device_id imx6_pcie_of_match[] = {
{ .compatible = "fsl,imx6q-pcie", },
{},
.owner = THIS_MODULE,
.of_match_table = imx6_pcie_of_match,
},
+ .shutdown = imx6_pcie_shutdown,
};
/* Freescale PCIe driver does not allow module unload */
{
return platform_driver_probe(&imx6_pcie_driver, imx6_pcie_probe);
}
-fs_initcall(imx6_pcie_init);
+module_init(imx6_pcie_init);
MODULE_AUTHOR("Sean Cross <xobs@kosagi.com>");
MODULE_DESCRIPTION("Freescale i.MX6 PCIe host controller driver");
--- /dev/null
+/*
+ * Designware application register space functions for Keystone PCI controller
+ *
+ * Copyright (C) 2013-2014 Texas Instruments., Ltd.
+ * http://www.ti.com
+ *
+ * Author: Murali Karicheri <m-karicheri2@ti.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+
+#include "pcie-designware.h"
+#include "pci-keystone.h"
+
+/* Application register defines */
+#define LTSSM_EN_VAL 1
+#define LTSSM_STATE_MASK 0x1f
+#define LTSSM_STATE_L0 0x11
+#define DBI_CS2_EN_VAL 0x20
+#define OB_XLAT_EN_VAL 2
+
+/* Application registers */
+#define CMD_STATUS 0x004
+#define CFG_SETUP 0x008
+#define OB_SIZE 0x030
+#define CFG_PCIM_WIN_SZ_IDX 3
+#define CFG_PCIM_WIN_CNT 32
+#define SPACE0_REMOTE_CFG_OFFSET 0x1000
+#define OB_OFFSET_INDEX(n) (0x200 + (8 * n))
+#define OB_OFFSET_HI(n) (0x204 + (8 * n))
+
+/* IRQ register defines */
+#define IRQ_EOI 0x050
+#define IRQ_STATUS 0x184
+#define IRQ_ENABLE_SET 0x188
+#define IRQ_ENABLE_CLR 0x18c
+
+#define MSI_IRQ 0x054
+#define MSI0_IRQ_STATUS 0x104
+#define MSI0_IRQ_ENABLE_SET 0x108
+#define MSI0_IRQ_ENABLE_CLR 0x10c
+#define IRQ_STATUS 0x184
+#define MSI_IRQ_OFFSET 4
+
+/* Config space registers */
+#define DEBUG0 0x728
+
+#define to_keystone_pcie(x) container_of(x, struct keystone_pcie, pp)
+
+static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
+{
+ return sys->private_data;
+}
+
+static inline void update_reg_offset_bit_pos(u32 offset, u32 *reg_offset,
+ u32 *bit_pos)
+{
+ *reg_offset = offset % 8;
+ *bit_pos = offset >> 3;
+}
+
+u32 ks_dw_pcie_get_msi_data(struct pcie_port *pp)
+{
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+ return ks_pcie->app.start + MSI_IRQ;
+}
+
+void ks_dw_pcie_handle_msi_irq(struct keystone_pcie *ks_pcie, int offset)
+{
+ struct pcie_port *pp = &ks_pcie->pp;
+ u32 pending, vector;
+ int src, virq;
+
+ pending = readl(ks_pcie->va_app_base + MSI0_IRQ_STATUS + (offset << 4));
+
+ /*
+ * MSI0 status bit 0-3 shows vectors 0, 8, 16, 24, MSI1 status bit
+ * shows 1, 9, 17, 25 and so forth
+ */
+ for (src = 0; src < 4; src++) {
+ if (BIT(src) & pending) {
+ vector = offset + (src << 3);
+ virq = irq_linear_revmap(pp->irq_domain, vector);
+ dev_dbg(pp->dev, "irq: bit %d, vector %d, virq %d\n",
+ src, vector, virq);
+ generic_handle_irq(virq);
+ }
+ }
+}
+
+static void ks_dw_pcie_msi_irq_ack(struct irq_data *d)
+{
+ u32 offset, reg_offset, bit_pos;
+ struct keystone_pcie *ks_pcie;
+ unsigned int irq = d->irq;
+ struct msi_desc *msi;
+ struct pcie_port *pp;
+
+ msi = irq_get_msi_desc(irq);
+ pp = sys_to_pcie(msi->dev->bus->sysdata);
+ ks_pcie = to_keystone_pcie(pp);
+ offset = irq - irq_linear_revmap(pp->irq_domain, 0);
+ update_reg_offset_bit_pos(offset, ®_offset, &bit_pos);
+
+ writel(BIT(bit_pos),
+ ks_pcie->va_app_base + MSI0_IRQ_STATUS + (reg_offset << 4));
+ writel(reg_offset + MSI_IRQ_OFFSET, ks_pcie->va_app_base + IRQ_EOI);
+}
+
+void ks_dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
+{
+ u32 reg_offset, bit_pos;
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+ update_reg_offset_bit_pos(irq, ®_offset, &bit_pos);
+ writel(BIT(bit_pos),
+ ks_pcie->va_app_base + MSI0_IRQ_ENABLE_SET + (reg_offset << 4));
+}
+
+void ks_dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq)
+{
+ u32 reg_offset, bit_pos;
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+ update_reg_offset_bit_pos(irq, ®_offset, &bit_pos);
+ writel(BIT(bit_pos),
+ ks_pcie->va_app_base + MSI0_IRQ_ENABLE_CLR + (reg_offset << 4));
+}
+
+static void ks_dw_pcie_msi_irq_mask(struct irq_data *d)
+{
+ struct keystone_pcie *ks_pcie;
+ unsigned int irq = d->irq;
+ struct msi_desc *msi;
+ struct pcie_port *pp;
+ u32 offset;
+
+ msi = irq_get_msi_desc(irq);
+ pp = sys_to_pcie(msi->dev->bus->sysdata);
+ ks_pcie = to_keystone_pcie(pp);
+ offset = irq - irq_linear_revmap(pp->irq_domain, 0);
+
+ /* Mask the end point if PVM implemented */
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ if (msi->msi_attrib.maskbit)
+ mask_msi_irq(d);
+ }
+
+ ks_dw_pcie_msi_clear_irq(pp, offset);
+}
+
+static void ks_dw_pcie_msi_irq_unmask(struct irq_data *d)
+{
+ struct keystone_pcie *ks_pcie;
+ unsigned int irq = d->irq;
+ struct msi_desc *msi;
+ struct pcie_port *pp;
+ u32 offset;
+
+ msi = irq_get_msi_desc(irq);
+ pp = sys_to_pcie(msi->dev->bus->sysdata);
+ ks_pcie = to_keystone_pcie(pp);
+ offset = irq - irq_linear_revmap(pp->irq_domain, 0);
+
+ /* Mask the end point if PVM implemented */
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ if (msi->msi_attrib.maskbit)
+ unmask_msi_irq(d);
+ }
+
+ ks_dw_pcie_msi_set_irq(pp, offset);
+}
+
+static struct irq_chip ks_dw_pcie_msi_irq_chip = {
+ .name = "Keystone-PCIe-MSI-IRQ",
+ .irq_ack = ks_dw_pcie_msi_irq_ack,
+ .irq_mask = ks_dw_pcie_msi_irq_mask,
+ .irq_unmask = ks_dw_pcie_msi_irq_unmask,
+};
+
+static int ks_dw_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_and_handler(irq, &ks_dw_pcie_msi_irq_chip,
+ handle_level_irq);
+ irq_set_chip_data(irq, domain->host_data);
+ set_irq_flags(irq, IRQF_VALID);
+
+ return 0;
+}
+
+const struct irq_domain_ops ks_dw_pcie_msi_domain_ops = {
+ .map = ks_dw_pcie_msi_map,
+};
+
+int ks_dw_pcie_msi_host_init(struct pcie_port *pp, struct msi_chip *chip)
+{
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+ int i;
+
+ pp->irq_domain = irq_domain_add_linear(ks_pcie->msi_intc_np,
+ MAX_MSI_IRQS,
+ &ks_dw_pcie_msi_domain_ops,
+ chip);
+ if (!pp->irq_domain) {
+ dev_err(pp->dev, "irq domain init failed\n");
+ return -ENXIO;
+ }
+
+ for (i = 0; i < MAX_MSI_IRQS; i++)
+ irq_create_mapping(pp->irq_domain, i);
+
+ return 0;
+}
+
+void ks_dw_pcie_enable_legacy_irqs(struct keystone_pcie *ks_pcie)
+{
+ int i;
+
+ for (i = 0; i < MAX_LEGACY_IRQS; i++)
+ writel(0x1, ks_pcie->va_app_base + IRQ_ENABLE_SET + (i << 4));
+}
+
+void ks_dw_pcie_handle_legacy_irq(struct keystone_pcie *ks_pcie, int offset)
+{
+ struct pcie_port *pp = &ks_pcie->pp;
+ u32 pending;
+ int virq;
+
+ pending = readl(ks_pcie->va_app_base + IRQ_STATUS + (offset << 4));
+
+ if (BIT(0) & pending) {
+ virq = irq_linear_revmap(ks_pcie->legacy_irq_domain, offset);
+ dev_dbg(pp->dev, ": irq: irq_offset %d, virq %d\n", offset,
+ virq);
+ generic_handle_irq(virq);
+ }
+
+ /* EOI the INTx interrupt */
+ writel(offset, ks_pcie->va_app_base + IRQ_EOI);
+}
+
+static void ks_dw_pcie_ack_legacy_irq(struct irq_data *d)
+{
+}
+
+static void ks_dw_pcie_mask_legacy_irq(struct irq_data *d)
+{
+}
+
+static void ks_dw_pcie_unmask_legacy_irq(struct irq_data *d)
+{
+}
+
+static struct irq_chip ks_dw_pcie_legacy_irq_chip = {
+ .name = "Keystone-PCI-Legacy-IRQ",
+ .irq_ack = ks_dw_pcie_ack_legacy_irq,
+ .irq_mask = ks_dw_pcie_mask_legacy_irq,
+ .irq_unmask = ks_dw_pcie_unmask_legacy_irq,
+};
+
+static int ks_dw_pcie_init_legacy_irq_map(struct irq_domain *d,
+ unsigned int irq, irq_hw_number_t hw_irq)
+{
+ irq_set_chip_and_handler(irq, &ks_dw_pcie_legacy_irq_chip,
+ handle_level_irq);
+ irq_set_chip_data(irq, d->host_data);
+ set_irq_flags(irq, IRQF_VALID);
+
+ return 0;
+}
+
+static const struct irq_domain_ops ks_dw_pcie_legacy_irq_domain_ops = {
+ .map = ks_dw_pcie_init_legacy_irq_map,
+ .xlate = irq_domain_xlate_onetwocell,
+};
+
+/**
+ * ks_dw_pcie_set_dbi_mode() - Set DBI mode to access overlaid BAR mask
+ * registers
+ *
+ * Since modification of dbi_cs2 involves different clock domain, read the
+ * status back to ensure the transition is complete.
+ */
+static void ks_dw_pcie_set_dbi_mode(void __iomem *reg_virt)
+{
+ u32 val;
+
+ writel(DBI_CS2_EN_VAL | readl(reg_virt + CMD_STATUS),
+ reg_virt + CMD_STATUS);
+
+ do {
+ val = readl(reg_virt + CMD_STATUS);
+ } while (!(val & DBI_CS2_EN_VAL));
+}
+
+/**
+ * ks_dw_pcie_clear_dbi_mode() - Disable DBI mode
+ *
+ * Since modification of dbi_cs2 involves different clock domain, read the
+ * status back to ensure the transition is complete.
+ */
+static void ks_dw_pcie_clear_dbi_mode(void __iomem *reg_virt)
+{
+ u32 val;
+
+ writel(~DBI_CS2_EN_VAL & readl(reg_virt + CMD_STATUS),
+ reg_virt + CMD_STATUS);
+
+ do {
+ val = readl(reg_virt + CMD_STATUS);
+ } while (val & DBI_CS2_EN_VAL);
+}
+
+void ks_dw_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie)
+{
+ struct pcie_port *pp = &ks_pcie->pp;
+ u32 start = pp->mem.start, end = pp->mem.end;
+ int i, tr_size;
+
+ /* Disable BARs for inbound access */
+ ks_dw_pcie_set_dbi_mode(ks_pcie->va_app_base);
+ writel(0, pp->dbi_base + PCI_BASE_ADDRESS_0);
+ writel(0, pp->dbi_base + PCI_BASE_ADDRESS_1);
+ ks_dw_pcie_clear_dbi_mode(ks_pcie->va_app_base);
+
+ /* Set outbound translation size per window division */
+ writel(CFG_PCIM_WIN_SZ_IDX & 0x7, ks_pcie->va_app_base + OB_SIZE);
+
+ tr_size = (1 << (CFG_PCIM_WIN_SZ_IDX & 0x7)) * SZ_1M;
+
+ /* Using Direct 1:1 mapping of RC <-> PCI memory space */
+ for (i = 0; (i < CFG_PCIM_WIN_CNT) && (start < end); i++) {
+ writel(start | 1, ks_pcie->va_app_base + OB_OFFSET_INDEX(i));
+ writel(0, ks_pcie->va_app_base + OB_OFFSET_HI(i));
+ start += tr_size;
+ }
+
+ /* Enable OB translation */
+ writel(OB_XLAT_EN_VAL | readl(ks_pcie->va_app_base + CMD_STATUS),
+ ks_pcie->va_app_base + CMD_STATUS);
+}
+
+/**
+ * ks_pcie_cfg_setup() - Set up configuration space address for a device
+ *
+ * @ks_pcie: ptr to keystone_pcie structure
+ * @bus: Bus number the device is residing on
+ * @devfn: device, function number info
+ *
+ * Forms and returns the address of configuration space mapped in PCIESS
+ * address space 0. Also configures CFG_SETUP for remote configuration space
+ * access.
+ *
+ * The address space has two regions to access configuration - local and remote.
+ * We access local region for bus 0 (as RC is attached on bus 0) and remote
+ * region for others with TYPE 1 access when bus > 1. As for device on bus = 1,
+ * we will do TYPE 0 access as it will be on our secondary bus (logical).
+ * CFG_SETUP is needed only for remote configuration access.
+ */
+static void __iomem *ks_pcie_cfg_setup(struct keystone_pcie *ks_pcie, u8 bus,
+ unsigned int devfn)
+{
+ u8 device = PCI_SLOT(devfn), function = PCI_FUNC(devfn);
+ struct pcie_port *pp = &ks_pcie->pp;
+ u32 regval;
+
+ if (bus == 0)
+ return pp->dbi_base;
+
+ regval = (bus << 16) | (device << 8) | function;
+
+ /*
+ * Since Bus#1 will be a virtual bus, we need to have TYPE0
+ * access only.
+ * TYPE 1
+ */
+ if (bus != 1)
+ regval |= BIT(24);
+
+ writel(regval, ks_pcie->va_app_base + CFG_SETUP);
+ return pp->va_cfg0_base;
+}
+
+int ks_dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+ unsigned int devfn, int where, int size, u32 *val)
+{
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+ u8 bus_num = bus->number;
+ void __iomem *addr;
+
+ addr = ks_pcie_cfg_setup(ks_pcie, bus_num, devfn);
+
+ return dw_pcie_cfg_read(addr + (where & ~0x3), where, size, val);
+}
+
+int ks_dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+ unsigned int devfn, int where, int size, u32 val)
+{
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+ u8 bus_num = bus->number;
+ void __iomem *addr;
+
+ addr = ks_pcie_cfg_setup(ks_pcie, bus_num, devfn);
+
+ return dw_pcie_cfg_write(addr + (where & ~0x3), where, size, val);
+}
+
+/**
+ * ks_dw_pcie_v3_65_scan_bus() - keystone scan_bus post initialization
+ *
+ * This sets BAR0 to enable inbound access for MSI_IRQ register
+ */
+void ks_dw_pcie_v3_65_scan_bus(struct pcie_port *pp)
+{
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+
+ /* Configure and set up BAR0 */
+ ks_dw_pcie_set_dbi_mode(ks_pcie->va_app_base);
+
+ /* Enable BAR0 */
+ writel(1, pp->dbi_base + PCI_BASE_ADDRESS_0);
+ writel(SZ_4K - 1, pp->dbi_base + PCI_BASE_ADDRESS_0);
+
+ ks_dw_pcie_clear_dbi_mode(ks_pcie->va_app_base);
+
+ /*
+ * For BAR0, just setting bus address for inbound writes (MSI) should
+ * be sufficient. Use physical address to avoid any conflicts.
+ */
+ writel(ks_pcie->app.start, pp->dbi_base + PCI_BASE_ADDRESS_0);
+}
+
+/**
+ * ks_dw_pcie_link_up() - Check if link up
+ */
+int ks_dw_pcie_link_up(struct pcie_port *pp)
+{
+ u32 val = readl(pp->dbi_base + DEBUG0);
+
+ return (val & LTSSM_STATE_MASK) == LTSSM_STATE_L0;
+}
+
+void ks_dw_pcie_initiate_link_train(struct keystone_pcie *ks_pcie)
+{
+ u32 val;
+
+ /* Disable Link training */
+ val = readl(ks_pcie->va_app_base + CMD_STATUS);
+ val &= ~LTSSM_EN_VAL;
+ writel(LTSSM_EN_VAL | val, ks_pcie->va_app_base + CMD_STATUS);
+
+ /* Initiate Link Training */
+ val = readl(ks_pcie->va_app_base + CMD_STATUS);
+ writel(LTSSM_EN_VAL | val, ks_pcie->va_app_base + CMD_STATUS);
+}
+
+/**
+ * ks_dw_pcie_host_init() - initialize host for v3_65 dw hardware
+ *
+ * Ioremap the register resources, initialize legacy irq domain
+ * and call dw_pcie_v3_65_host_init() API to initialize the Keystone
+ * PCI host controller.
+ */
+int __init ks_dw_pcie_host_init(struct keystone_pcie *ks_pcie,
+ struct device_node *msi_intc_np)
+{
+ struct pcie_port *pp = &ks_pcie->pp;
+ struct platform_device *pdev = to_platform_device(pp->dev);
+ struct resource *res;
+
+ /* Index 0 is the config reg. space address */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pp->dbi_base = devm_ioremap_resource(pp->dev, res);
+ if (IS_ERR(pp->dbi_base))
+ return PTR_ERR(pp->dbi_base);
+
+ /*
+ * We set these same and is used in pcie rd/wr_other_conf
+ * functions
+ */
+ pp->va_cfg0_base = pp->dbi_base + SPACE0_REMOTE_CFG_OFFSET;
+ pp->va_cfg1_base = pp->va_cfg0_base;
+
+ /* Index 1 is the application reg. space address */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ ks_pcie->app = *res;
+ ks_pcie->va_app_base = devm_ioremap_resource(pp->dev, res);
+ if (IS_ERR(ks_pcie->va_app_base))
+ return PTR_ERR(ks_pcie->va_app_base);
+
+ /* Create legacy IRQ domain */
+ ks_pcie->legacy_irq_domain =
+ irq_domain_add_linear(ks_pcie->legacy_intc_np,
+ MAX_LEGACY_IRQS,
+ &ks_dw_pcie_legacy_irq_domain_ops,
+ NULL);
+ if (!ks_pcie->legacy_irq_domain) {
+ dev_err(pp->dev, "Failed to add irq domain for legacy irqs\n");
+ return -EINVAL;
+ }
+
+ return dw_pcie_host_init(pp);
+}
--- /dev/null
+/*
+ * PCIe host controller driver for Texas Instruments Keystone SoCs
+ *
+ * Copyright (C) 2013-2014 Texas Instruments., Ltd.
+ * http://www.ti.com
+ *
+ * Author: Murali Karicheri <m-karicheri2@ti.com>
+ * Implementation based on pci-exynos.c and pcie-designware.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/irqchip/chained_irq.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_irq.h>
+#include <linux/of.h>
+#include <linux/of_pci.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/resource.h>
+#include <linux/signal.h>
+
+#include "pcie-designware.h"
+#include "pci-keystone.h"
+
+#define DRIVER_NAME "keystone-pcie"
+
+/* driver specific constants */
+#define MAX_MSI_HOST_IRQS 8
+#define MAX_LEGACY_HOST_IRQS 4
+
+/* DEV_STAT_CTRL */
+#define PCIE_CAP_BASE 0x70
+
+/* PCIE controller device IDs */
+#define PCIE_RC_K2HK 0xb008
+#define PCIE_RC_K2E 0xb009
+#define PCIE_RC_K2L 0xb00a
+
+#define to_keystone_pcie(x) container_of(x, struct keystone_pcie, pp)
+
+static void quirk_limit_mrrs(struct pci_dev *dev)
+{
+ struct pci_bus *bus = dev->bus;
+ struct pci_dev *bridge = bus->self;
+ static const struct pci_device_id rc_pci_devids[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2HK),
+ .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, },
+ { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2E),
+ .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, },
+ { PCI_DEVICE(PCI_VENDOR_ID_TI, PCIE_RC_K2L),
+ .class = PCI_CLASS_BRIDGE_PCI << 8, .class_mask = ~0, },
+ { 0, },
+ };
+
+ if (pci_is_root_bus(bus))
+ return;
+
+ /* look for the host bridge */
+ while (!pci_is_root_bus(bus)) {
+ bridge = bus->self;
+ bus = bus->parent;
+ }
+
+ if (bridge) {
+ /*
+ * Keystone PCI controller has a h/w limitation of
+ * 256 bytes maximum read request size. It can't handle
+ * anything higher than this. So force this limit on
+ * all downstream devices.
+ */
+ if (pci_match_id(rc_pci_devids, bridge)) {
+ if (pcie_get_readrq(dev) > 256) {
+ dev_info(&dev->dev, "limiting MRRS to 256\n");
+ pcie_set_readrq(dev, 256);
+ }
+ }
+ }
+}
+DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, quirk_limit_mrrs);
+
+static int ks_pcie_establish_link(struct keystone_pcie *ks_pcie)
+{
+ struct pcie_port *pp = &ks_pcie->pp;
+ int count = 200;
+
+ dw_pcie_setup_rc(pp);
+
+ if (dw_pcie_link_up(pp)) {
+ dev_err(pp->dev, "Link already up\n");
+ return 0;
+ }
+
+ ks_dw_pcie_initiate_link_train(ks_pcie);
+ /* check if the link is up or not */
+ while (!dw_pcie_link_up(pp)) {
+ usleep_range(100, 1000);
+ if (--count) {
+ ks_dw_pcie_initiate_link_train(ks_pcie);
+ continue;
+ }
+ dev_err(pp->dev, "phy link never came up\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void ks_pcie_msi_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc);
+ u32 offset = irq - ks_pcie->msi_host_irqs[0];
+ struct pcie_port *pp = &ks_pcie->pp;
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+
+ dev_dbg(pp->dev, "ks_pci_msi_irq_handler, irq %d\n", irq);
+
+ /*
+ * The chained irq handler installation would have replaced normal
+ * interrupt driver handler so we need to take care of mask/unmask and
+ * ack operation.
+ */
+ chained_irq_enter(chip, desc);
+ ks_dw_pcie_handle_msi_irq(ks_pcie, offset);
+ chained_irq_exit(chip, desc);
+}
+
+/**
+ * ks_pcie_legacy_irq_handler() - Handle legacy interrupt
+ * @irq: IRQ line for legacy interrupts
+ * @desc: Pointer to irq descriptor
+ *
+ * Traverse through pending legacy interrupts and invoke handler for each. Also
+ * takes care of interrupt controller level mask/ack operation.
+ */
+static void ks_pcie_legacy_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ struct keystone_pcie *ks_pcie = irq_desc_get_handler_data(desc);
+ struct pcie_port *pp = &ks_pcie->pp;
+ u32 irq_offset = irq - ks_pcie->legacy_host_irqs[0];
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+
+ dev_dbg(pp->dev, ": Handling legacy irq %d\n", irq);
+
+ /*
+ * The chained irq handler installation would have replaced normal
+ * interrupt driver handler so we need to take care of mask/unmask and
+ * ack operation.
+ */
+ chained_irq_enter(chip, desc);
+ ks_dw_pcie_handle_legacy_irq(ks_pcie, irq_offset);
+ chained_irq_exit(chip, desc);
+}
+
+static int ks_pcie_get_irq_controller_info(struct keystone_pcie *ks_pcie,
+ char *controller, int *num_irqs)
+{
+ int temp, max_host_irqs, legacy = 1, *host_irqs, ret = -EINVAL;
+ struct device *dev = ks_pcie->pp.dev;
+ struct device_node *np_pcie = dev->of_node, **np_temp;
+
+ if (!strcmp(controller, "msi-interrupt-controller"))
+ legacy = 0;
+
+ if (legacy) {
+ np_temp = &ks_pcie->legacy_intc_np;
+ max_host_irqs = MAX_LEGACY_HOST_IRQS;
+ host_irqs = &ks_pcie->legacy_host_irqs[0];
+ } else {
+ np_temp = &ks_pcie->msi_intc_np;
+ max_host_irqs = MAX_MSI_HOST_IRQS;
+ host_irqs = &ks_pcie->msi_host_irqs[0];
+ }
+
+ /* interrupt controller is in a child node */
+ *np_temp = of_find_node_by_name(np_pcie, controller);
+ if (!(*np_temp)) {
+ dev_err(dev, "Node for %s is absent\n", controller);
+ goto out;
+ }
+ temp = of_irq_count(*np_temp);
+ if (!temp)
+ goto out;
+ if (temp > max_host_irqs)
+ dev_warn(dev, "Too many %s interrupts defined %u\n",
+ (legacy ? "legacy" : "MSI"), temp);
+
+ /*
+ * support upto max_host_irqs. In dt from index 0 to 3 (legacy) or 0 to
+ * 7 (MSI)
+ */
+ for (temp = 0; temp < max_host_irqs; temp++) {
+ host_irqs[temp] = irq_of_parse_and_map(*np_temp, temp);
+ if (host_irqs[temp] < 0)
+ break;
+ }
+ if (temp) {
+ *num_irqs = temp;
+ ret = 0;
+ }
+out:
+ return ret;
+}
+
+static void ks_pcie_setup_interrupts(struct keystone_pcie *ks_pcie)
+{
+ int i;
+
+ /* Legacy IRQ */
+ for (i = 0; i < ks_pcie->num_legacy_host_irqs; i++) {
+ irq_set_handler_data(ks_pcie->legacy_host_irqs[i], ks_pcie);
+ irq_set_chained_handler(ks_pcie->legacy_host_irqs[i],
+ ks_pcie_legacy_irq_handler);
+ }
+ ks_dw_pcie_enable_legacy_irqs(ks_pcie);
+
+ /* MSI IRQ */
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ for (i = 0; i < ks_pcie->num_msi_host_irqs; i++) {
+ irq_set_chained_handler(ks_pcie->msi_host_irqs[i],
+ ks_pcie_msi_irq_handler);
+ irq_set_handler_data(ks_pcie->msi_host_irqs[i],
+ ks_pcie);
+ }
+ }
+}
+
+/*
+ * When a PCI device does not exist during config cycles, keystone host gets a
+ * bus error instead of returning 0xffffffff. This handler always returns 0
+ * for this kind of faults.
+ */
+static int keystone_pcie_fault(unsigned long addr, unsigned int fsr,
+ struct pt_regs *regs)
+{
+ unsigned long instr = *(unsigned long *) instruction_pointer(regs);
+
+ if ((instr & 0x0e100090) == 0x00100090) {
+ int reg = (instr >> 12) & 15;
+
+ regs->uregs[reg] = -1;
+ regs->ARM_pc += 4;
+ }
+
+ return 0;
+}
+
+static void __init ks_pcie_host_init(struct pcie_port *pp)
+{
+ struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+ u32 val;
+
+ ks_pcie_establish_link(ks_pcie);
+ ks_dw_pcie_setup_rc_app_regs(ks_pcie);
+ ks_pcie_setup_interrupts(ks_pcie);
+ writew(PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8),
+ pp->dbi_base + PCI_IO_BASE);
+
+ /* update the Vendor ID */
+ writew(ks_pcie->device_id, pp->dbi_base + PCI_DEVICE_ID);
+
+ /* update the DEV_STAT_CTRL to publish right mrrs */
+ val = readl(pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
+ val &= ~PCI_EXP_DEVCTL_READRQ;
+ /* set the mrrs to 256 bytes */
+ val |= BIT(12);
+ writel(val, pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
+
+ /*
+ * PCIe access errors that result into OCP errors are caught by ARM as
+ * "External aborts"
+ */
+ hook_fault_code(17, keystone_pcie_fault, SIGBUS, 0,
+ "Asynchronous external abort");
+}
+
+static struct pcie_host_ops keystone_pcie_host_ops = {
+ .rd_other_conf = ks_dw_pcie_rd_other_conf,
+ .wr_other_conf = ks_dw_pcie_wr_other_conf,
+ .link_up = ks_dw_pcie_link_up,
+ .host_init = ks_pcie_host_init,
+ .msi_set_irq = ks_dw_pcie_msi_set_irq,
+ .msi_clear_irq = ks_dw_pcie_msi_clear_irq,
+ .get_msi_data = ks_dw_pcie_get_msi_data,
+ .msi_host_init = ks_dw_pcie_msi_host_init,
+ .scan_bus = ks_dw_pcie_v3_65_scan_bus,
+};
+
+static int __init ks_add_pcie_port(struct keystone_pcie *ks_pcie,
+ struct platform_device *pdev)
+{
+ struct pcie_port *pp = &ks_pcie->pp;
+ int ret;
+
+ ret = ks_pcie_get_irq_controller_info(ks_pcie,
+ "legacy-interrupt-controller",
+ &ks_pcie->num_legacy_host_irqs);
+ if (ret)
+ return ret;
+
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ ret = ks_pcie_get_irq_controller_info(ks_pcie,
+ "msi-interrupt-controller",
+ &ks_pcie->num_msi_host_irqs);
+ if (ret)
+ return ret;
+ }
+
+ pp->root_bus_nr = -1;
+ pp->ops = &keystone_pcie_host_ops;
+ ret = ks_dw_pcie_host_init(ks_pcie, ks_pcie->msi_intc_np);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to initialize host\n");
+ return ret;
+ }
+
+ return ret;
+}
+
+static const struct of_device_id ks_pcie_of_match[] = {
+ {
+ .type = "pci",
+ .compatible = "ti,keystone-pcie",
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ks_pcie_of_match);
+
+static int __exit ks_pcie_remove(struct platform_device *pdev)
+{
+ struct keystone_pcie *ks_pcie = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(ks_pcie->clk);
+
+ return 0;
+}
+
+static int __init ks_pcie_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct keystone_pcie *ks_pcie;
+ struct pcie_port *pp;
+ struct resource *res;
+ void __iomem *reg_p;
+ struct phy *phy;
+ int ret = 0;
+
+ ks_pcie = devm_kzalloc(&pdev->dev, sizeof(*ks_pcie),
+ GFP_KERNEL);
+ if (!ks_pcie) {
+ dev_err(dev, "no memory for keystone pcie\n");
+ return -ENOMEM;
+ }
+ pp = &ks_pcie->pp;
+
+ /* initialize SerDes Phy if present */
+ phy = devm_phy_get(dev, "pcie-phy");
+ if (!IS_ERR_OR_NULL(phy)) {
+ ret = phy_init(phy);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* index 2 is to read PCI DEVICE_ID */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ reg_p = devm_ioremap_resource(dev, res);
+ if (IS_ERR(reg_p))
+ return PTR_ERR(reg_p);
+ ks_pcie->device_id = readl(reg_p) >> 16;
+ devm_iounmap(dev, reg_p);
+ devm_release_mem_region(dev, res->start, resource_size(res));
+
+ pp->dev = dev;
+ platform_set_drvdata(pdev, ks_pcie);
+ ks_pcie->clk = devm_clk_get(dev, "pcie");
+ if (IS_ERR(ks_pcie->clk)) {
+ dev_err(dev, "Failed to get pcie rc clock\n");
+ return PTR_ERR(ks_pcie->clk);
+ }
+ ret = clk_prepare_enable(ks_pcie->clk);
+ if (ret)
+ return ret;
+
+ ret = ks_add_pcie_port(ks_pcie, pdev);
+ if (ret < 0)
+ goto fail_clk;
+
+ return 0;
+fail_clk:
+ clk_disable_unprepare(ks_pcie->clk);
+
+ return ret;
+}
+
+static struct platform_driver ks_pcie_driver __refdata = {
+ .probe = ks_pcie_probe,
+ .remove = __exit_p(ks_pcie_remove),
+ .driver = {
+ .name = "keystone-pcie",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(ks_pcie_of_match),
+ },
+};
+
+module_platform_driver(ks_pcie_driver);
+
+MODULE_AUTHOR("Murali Karicheri <m-karicheri2@ti.com>");
+MODULE_DESCRIPTION("Keystone PCIe host controller driver");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+/*
+ * Keystone PCI Controller's common includes
+ *
+ * Copyright (C) 2013-2014 Texas Instruments., Ltd.
+ * http://www.ti.com
+ *
+ * Author: Murali Karicheri <m-karicheri2@ti.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define MAX_LEGACY_IRQS 4
+#define MAX_MSI_HOST_IRQS 8
+#define MAX_LEGACY_HOST_IRQS 4
+
+struct keystone_pcie {
+ struct clk *clk;
+ struct pcie_port pp;
+ /* PCI Device ID */
+ u32 device_id;
+ int num_legacy_host_irqs;
+ int legacy_host_irqs[MAX_LEGACY_HOST_IRQS];
+ struct device_node *legacy_intc_np;
+
+ int num_msi_host_irqs;
+ int msi_host_irqs[MAX_MSI_HOST_IRQS];
+ struct device_node *msi_intc_np;
+ struct irq_domain *legacy_irq_domain;
+
+ /* Application register space */
+ void __iomem *va_app_base;
+ struct resource app;
+};
+
+/* Keystone DW specific MSI controller APIs/definitions */
+void ks_dw_pcie_handle_msi_irq(struct keystone_pcie *ks_pcie, int offset);
+u32 ks_dw_pcie_get_msi_data(struct pcie_port *pp);
+
+/* Keystone specific PCI controller APIs */
+void ks_dw_pcie_enable_legacy_irqs(struct keystone_pcie *ks_pcie);
+void ks_dw_pcie_handle_legacy_irq(struct keystone_pcie *ks_pcie, int offset);
+int ks_dw_pcie_host_init(struct keystone_pcie *ks_pcie,
+ struct device_node *msi_intc_np);
+int ks_dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+ unsigned int devfn, int where, int size, u32 val);
+int ks_dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+ unsigned int devfn, int where, int size, u32 *val);
+void ks_dw_pcie_setup_rc_app_regs(struct keystone_pcie *ks_pcie);
+int ks_dw_pcie_link_up(struct pcie_port *pp);
+void ks_dw_pcie_initiate_link_train(struct keystone_pcie *ks_pcie);
+void ks_dw_pcie_msi_set_irq(struct pcie_port *pp, int irq);
+void ks_dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq);
+void ks_dw_pcie_v3_65_scan_bus(struct pcie_port *pp);
+int ks_dw_pcie_msi_host_init(struct pcie_port *pp,
+ struct msi_chip *chip);
rangesz = pna + na + ns;
nranges = rlen / sizeof(__be32) / rangesz;
- for (i = 0; i < nranges; i++) {
+ for (i = 0; i < nranges; i++, range += rangesz) {
u32 flags = of_read_number(range, 1);
u32 slot = of_read_number(range + 1, 1);
u64 cpuaddr = of_read_number(range + na, pna);
rtype = IORESOURCE_IO;
else if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_MEM32)
rtype = IORESOURCE_MEM;
+ else
+ continue;
if (slot == PCI_SLOT(devfn) && type == rtype) {
*tgt = DT_CPUADDR_TO_TARGET(cpuaddr);
*attr = DT_CPUADDR_TO_ATTR(cpuaddr);
return 0;
}
-
- range += rangesz;
}
return -ENOENT;
#include <linux/of_pci.h>
#include <linux/of_platform.h>
#include <linux/pci.h>
+#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/reset.h>
#include <linux/sizes.h>
#define AFI_INTR_CODE 0xb8
#define AFI_INTR_CODE_MASK 0xf
-#define AFI_INTR_AXI_SLAVE_ERROR 1
-#define AFI_INTR_AXI_DECODE_ERROR 2
+#define AFI_INTR_INI_SLAVE_ERROR 1
+#define AFI_INTR_INI_DECODE_ERROR 2
#define AFI_INTR_TARGET_ABORT 3
#define AFI_INTR_MASTER_ABORT 4
#define AFI_INTR_INVALID_WRITE 5
#define AFI_INTR_LEGACY 6
#define AFI_INTR_FPCI_DECODE_ERROR 7
+#define AFI_INTR_AXI_DECODE_ERROR 8
+#define AFI_INTR_FPCI_TIMEOUT 9
+#define AFI_INTR_PE_PRSNT_SENSE 10
+#define AFI_INTR_PE_CLKREQ_SENSE 11
+#define AFI_INTR_CLKCLAMP_SENSE 12
+#define AFI_INTR_RDY4PD_SENSE 13
+#define AFI_INTR_P2P_ERROR 14
#define AFI_INTR_SIGNATURE 0xbc
#define AFI_UPPER_FPCI_ADDRESS 0xc0
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_MASK (0xf << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_SINGLE (0x0 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_420 (0x0 << 20)
+#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_X2_X1 (0x0 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_DUAL (0x1 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_222 (0x1 << 20)
+#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_X4_X1 (0x1 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_411 (0x2 << 20)
#define AFI_FUSE 0x104
#define AFI_PEX_CTRL_RST (1 << 0)
#define AFI_PEX_CTRL_CLKREQ_EN (1 << 1)
#define AFI_PEX_CTRL_REFCLK_EN (1 << 3)
+#define AFI_PEX_CTRL_OVERRIDE_EN (1 << 4)
+
+#define AFI_PLLE_CONTROL 0x160
+#define AFI_PLLE_CONTROL_BYPASS_PADS2PLLE_CONTROL (1 << 9)
+#define AFI_PLLE_CONTROL_PADS2PLLE_CONTROL_EN (1 << 1)
#define AFI_PEXBIAS_CTRL_0 0x168
#define RP_VEND_XP 0x00000F00
#define RP_VEND_XP_DL_UP (1 << 30)
+#define RP_PRIV_MISC 0x00000FE0
+#define RP_PRIV_MISC_PRSNT_MAP_EP_PRSNT (0xE << 0)
+#define RP_PRIV_MISC_PRSNT_MAP_EP_ABSNT (0xF << 0)
+
#define RP_LINK_CONTROL_STATUS 0x00000090
#define RP_LINK_CONTROL_STATUS_DL_LINK_ACTIVE 0x20000000
#define RP_LINK_CONTROL_STATUS_LINKSTAT_MASK 0x3fff0000
#define PADS_REFCLK_CFG0 0x000000C8
#define PADS_REFCLK_CFG1 0x000000CC
+#define PADS_REFCLK_BIAS 0x000000D0
/*
* Fields in PADS_REFCLK_CFG*. Those registers form an array of 16-bit
bool has_pex_bias_ctrl;
bool has_intr_prsnt_sense;
bool has_cml_clk;
+ bool has_gen2;
};
static inline struct tegra_msi *to_tegra_msi(struct msi_chip *chip)
struct list_head buses;
struct resource *cs;
+ struct resource all;
struct resource io;
struct resource mem;
struct resource prefetch;
struct reset_control *afi_rst;
struct reset_control *pcie_xrst;
+ struct phy *phy;
+
struct tegra_msi msi;
struct list_head ports;
for (i = 0; i < 16; i++) {
unsigned long virt = (unsigned long)bus->area->addr +
i * SZ_64K;
- phys_addr_t phys = cs + i * SZ_1M + busnr * SZ_64K;
+ phys_addr_t phys = cs + i * SZ_16M + busnr * SZ_64K;
err = ioremap_page_range(virt, virt + SZ_64K, phys, prot);
if (err < 0) {
if (soc->has_pex_clkreq_en)
value |= AFI_PEX_CTRL_CLKREQ_EN;
+ value |= AFI_PEX_CTRL_OVERRIDE_EN;
+
afi_writel(port->pcie, value, ctrl);
tegra_pcie_port_reset(port);
static void tegra_pcie_port_disable(struct tegra_pcie_port *port)
{
+ const struct tegra_pcie_soc_data *soc = port->pcie->soc_data;
unsigned long ctrl = tegra_pcie_port_get_pex_ctrl(port);
unsigned long value;
/* disable reference clock */
value = afi_readl(port->pcie, ctrl);
+
+ if (soc->has_pex_clkreq_en)
+ value &= ~AFI_PEX_CTRL_CLKREQ_EN;
+
value &= ~AFI_PEX_CTRL_REFCLK_EN;
afi_writel(port->pcie, value, ctrl);
}
static int tegra_pcie_setup(int nr, struct pci_sys_data *sys)
{
struct tegra_pcie *pcie = sys_to_pcie(sys);
+ int err;
+
+ err = devm_request_resource(pcie->dev, &pcie->all, &pcie->mem);
+ if (err < 0)
+ return err;
+
+ err = devm_request_resource(pcie->dev, &pcie->all, &pcie->prefetch);
+ if (err)
+ return err;
pci_add_resource_offset(&sys->resources, &pcie->mem, sys->mem_offset);
pci_add_resource_offset(&sys->resources, &pcie->prefetch,
"Target abort",
"Master abort",
"Invalid write",
+ "Legacy interrupt",
"Response decoding error",
"AXI response decoding error",
"Transaction timeout",
+ "Slot present pin change",
+ "Slot clock request change",
+ "TMS clock ramp change",
+ "TMS ready for power down",
+ "Peer2Peer error",
};
struct tegra_pcie *pcie = arg;
u32 code, signature;
afi_writel(pcie, 0, AFI_MSI_BAR_SZ);
}
-static int tegra_pcie_enable_controller(struct tegra_pcie *pcie)
+static int tegra_pcie_pll_wait(struct tegra_pcie *pcie, unsigned long timeout)
{
const struct tegra_pcie_soc_data *soc = pcie->soc_data;
- struct tegra_pcie_port *port;
- unsigned int timeout;
- unsigned long value;
-
- /* power down PCIe slot clock bias pad */
- if (soc->has_pex_bias_ctrl)
- afi_writel(pcie, 0, AFI_PEXBIAS_CTRL_0);
+ u32 value;
- /* configure mode and disable all ports */
- value = afi_readl(pcie, AFI_PCIE_CONFIG);
- value &= ~AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_MASK;
- value |= AFI_PCIE_CONFIG_PCIE_DISABLE_ALL | pcie->xbar_config;
+ timeout = jiffies + msecs_to_jiffies(timeout);
- list_for_each_entry(port, &pcie->ports, list)
- value &= ~AFI_PCIE_CONFIG_PCIE_DISABLE(port->index);
+ while (time_before(jiffies, timeout)) {
+ value = pads_readl(pcie, soc->pads_pll_ctl);
+ if (value & PADS_PLL_CTL_LOCKDET)
+ return 0;
+ }
- afi_writel(pcie, value, AFI_PCIE_CONFIG);
+ return -ETIMEDOUT;
+}
- value = afi_readl(pcie, AFI_FUSE);
- value |= AFI_FUSE_PCIE_T0_GEN2_DIS;
- afi_writel(pcie, value, AFI_FUSE);
+static int tegra_pcie_phy_enable(struct tegra_pcie *pcie)
+{
+ const struct tegra_pcie_soc_data *soc = pcie->soc_data;
+ u32 value;
+ int err;
/* initialize internal PHY, enable up to 16 PCIE lanes */
pads_writel(pcie, 0x0, PADS_CTL_SEL);
value |= PADS_PLL_CTL_REFCLK_INTERNAL_CML | soc->tx_ref_sel;
pads_writel(pcie, value, soc->pads_pll_ctl);
+ /* reset PLL */
+ value = pads_readl(pcie, soc->pads_pll_ctl);
+ value &= ~PADS_PLL_CTL_RST_B4SM;
+ pads_writel(pcie, value, soc->pads_pll_ctl);
+
+ usleep_range(20, 100);
+
/* take PLL out of reset */
value = pads_readl(pcie, soc->pads_pll_ctl);
value |= PADS_PLL_CTL_RST_B4SM;
pads_writel(pcie, PADS_REFCLK_CFG_VALUE, PADS_REFCLK_CFG1);
/* wait for the PLL to lock */
- timeout = 300;
- do {
- value = pads_readl(pcie, soc->pads_pll_ctl);
- usleep_range(1000, 2000);
- if (--timeout == 0) {
- pr_err("Tegra PCIe error: timeout waiting for PLL\n");
- return -EBUSY;
- }
- } while (!(value & PADS_PLL_CTL_LOCKDET));
+ err = tegra_pcie_pll_wait(pcie, 500);
+ if (err < 0) {
+ dev_err(pcie->dev, "PLL failed to lock: %d\n", err);
+ return err;
+ }
/* turn off IDDQ override */
value = pads_readl(pcie, PADS_CTL);
value |= PADS_CTL_TX_DATA_EN_1L | PADS_CTL_RX_DATA_EN_1L;
pads_writel(pcie, value, PADS_CTL);
+ return 0;
+}
+
+static int tegra_pcie_enable_controller(struct tegra_pcie *pcie)
+{
+ const struct tegra_pcie_soc_data *soc = pcie->soc_data;
+ struct tegra_pcie_port *port;
+ unsigned long value;
+ int err;
+
+ /* enable PLL power down */
+ if (pcie->phy) {
+ value = afi_readl(pcie, AFI_PLLE_CONTROL);
+ value &= ~AFI_PLLE_CONTROL_BYPASS_PADS2PLLE_CONTROL;
+ value |= AFI_PLLE_CONTROL_PADS2PLLE_CONTROL_EN;
+ afi_writel(pcie, value, AFI_PLLE_CONTROL);
+ }
+
+ /* power down PCIe slot clock bias pad */
+ if (soc->has_pex_bias_ctrl)
+ afi_writel(pcie, 0, AFI_PEXBIAS_CTRL_0);
+
+ /* configure mode and disable all ports */
+ value = afi_readl(pcie, AFI_PCIE_CONFIG);
+ value &= ~AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_MASK;
+ value |= AFI_PCIE_CONFIG_PCIE_DISABLE_ALL | pcie->xbar_config;
+
+ list_for_each_entry(port, &pcie->ports, list)
+ value &= ~AFI_PCIE_CONFIG_PCIE_DISABLE(port->index);
+
+ afi_writel(pcie, value, AFI_PCIE_CONFIG);
+
+ if (soc->has_gen2) {
+ value = afi_readl(pcie, AFI_FUSE);
+ value &= ~AFI_FUSE_PCIE_T0_GEN2_DIS;
+ afi_writel(pcie, value, AFI_FUSE);
+ } else {
+ value = afi_readl(pcie, AFI_FUSE);
+ value |= AFI_FUSE_PCIE_T0_GEN2_DIS;
+ afi_writel(pcie, value, AFI_FUSE);
+ }
+
+ if (!pcie->phy)
+ err = tegra_pcie_phy_enable(pcie);
+ else
+ err = phy_power_on(pcie->phy);
+
+ if (err < 0) {
+ dev_err(pcie->dev, "failed to power on PHY: %d\n", err);
+ return err;
+ }
+
/* take the PCIe interface module out of reset */
reset_control_deassert(pcie->pcie_xrst);
/* TODO: disable and unprepare clocks? */
+ err = phy_power_off(pcie->phy);
+ if (err < 0)
+ dev_warn(pcie->dev, "failed to power off PHY: %d\n", err);
+
reset_control_assert(pcie->pcie_xrst);
reset_control_assert(pcie->afi_rst);
reset_control_assert(pcie->pex_rst);
return err;
}
+ pcie->phy = devm_phy_optional_get(pcie->dev, "pcie");
+ if (IS_ERR(pcie->phy)) {
+ err = PTR_ERR(pcie->phy);
+ dev_err(&pdev->dev, "failed to get PHY: %d\n", err);
+ return err;
+ }
+
+ err = phy_init(pcie->phy);
+ if (err < 0) {
+ dev_err(&pdev->dev, "failed to initialize PHY: %d\n", err);
+ return err;
+ }
+
err = tegra_pcie_power_on(pcie);
if (err) {
dev_err(&pdev->dev, "failed to power up: %d\n", err);
static int tegra_pcie_put_resources(struct tegra_pcie *pcie)
{
+ int err;
+
if (pcie->irq > 0)
free_irq(pcie->irq, pcie);
tegra_pcie_power_off(pcie);
+
+ err = phy_exit(pcie->phy);
+ if (err < 0)
+ dev_err(pcie->dev, "failed to teardown PHY: %d\n", err);
+
return 0;
}
return hwirq;
irq = irq_create_mapping(msi->domain, hwirq);
- if (!irq)
+ if (!irq) {
+ tegra_msi_free(msi, hwirq);
return -EINVAL;
+ }
irq_set_msi_desc(irq, desc);
{
struct tegra_msi *msi = to_tegra_msi(chip);
struct irq_data *d = irq_get_irq_data(irq);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
- tegra_msi_free(msi, d->hwirq);
+ irq_dispose_mapping(irq);
+ tegra_msi_free(msi, hwirq);
}
static struct irq_chip tegra_msi_irq_chip = {
{
struct device_node *np = pcie->dev->of_node;
- if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
+ if (of_device_is_compatible(np, "nvidia,tegra124-pcie")) {
+ switch (lanes) {
+ case 0x0000104:
+ dev_info(pcie->dev, "4x1, 1x1 configuration\n");
+ *xbar = AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_X4_X1;
+ return 0;
+
+ case 0x0000102:
+ dev_info(pcie->dev, "2x1, 1x1 configuration\n");
+ *xbar = AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_X2_X1;
+ return 0;
+ }
+ } else if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
switch (lanes) {
case 0x00000204:
dev_info(pcie->dev, "4x1, 2x1 configuration\n");
struct device_node *np = pcie->dev->of_node;
unsigned int i = 0;
- if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
+ if (of_device_is_compatible(np, "nvidia,tegra124-pcie")) {
+ pcie->num_supplies = 7;
+
+ pcie->supplies = devm_kcalloc(pcie->dev, pcie->num_supplies,
+ sizeof(*pcie->supplies),
+ GFP_KERNEL);
+ if (!pcie->supplies)
+ return -ENOMEM;
+
+ pcie->supplies[i++].supply = "avddio-pex";
+ pcie->supplies[i++].supply = "dvddio-pex";
+ pcie->supplies[i++].supply = "avdd-pex-pll";
+ pcie->supplies[i++].supply = "hvdd-pex";
+ pcie->supplies[i++].supply = "hvdd-pex-pll-e";
+ pcie->supplies[i++].supply = "vddio-pex-ctl";
+ pcie->supplies[i++].supply = "avdd-pll-erefe";
+ } else if (of_device_is_compatible(np, "nvidia,tegra30-pcie")) {
bool need_pexa = false, need_pexb = false;
/* VDD_PEXA and AVDD_PEXA supply lanes 0 to 3 */
struct resource res;
int err;
+ memset(&pcie->all, 0, sizeof(pcie->all));
+ pcie->all.flags = IORESOURCE_MEM;
+ pcie->all.name = np->full_name;
+ pcie->all.start = ~0;
+ pcie->all.end = 0;
+
if (of_pci_range_parser_init(&parser, np)) {
dev_err(pcie->dev, "missing \"ranges\" property\n");
return -EINVAL;
switch (res.flags & IORESOURCE_TYPE_BITS) {
case IORESOURCE_IO:
memcpy(&pcie->io, &res, sizeof(res));
- pcie->io.name = "I/O";
+ pcie->io.name = np->full_name;
break;
case IORESOURCE_MEM:
if (res.flags & IORESOURCE_PREFETCH) {
memcpy(&pcie->prefetch, &res, sizeof(res));
- pcie->prefetch.name = "PREFETCH";
+ pcie->prefetch.name = "prefetchable";
} else {
memcpy(&pcie->mem, &res, sizeof(res));
- pcie->mem.name = "MEM";
+ pcie->mem.name = "non-prefetchable";
}
break;
}
+
+ if (res.start <= pcie->all.start)
+ pcie->all.start = res.start;
+
+ if (res.end >= pcie->all.end)
+ pcie->all.end = res.end;
}
+ err = devm_request_resource(pcie->dev, &iomem_resource, &pcie->all);
+ if (err < 0)
+ return err;
+
err = of_pci_parse_bus_range(np, &pcie->busn);
if (err < 0) {
dev_err(pcie->dev, "failed to parse ranges property: %d\n",
unsigned int retries = 3;
unsigned long value;
+ /* override presence detection */
+ value = readl(port->base + RP_PRIV_MISC);
+ value &= ~RP_PRIV_MISC_PRSNT_MAP_EP_ABSNT;
+ value |= RP_PRIV_MISC_PRSNT_MAP_EP_PRSNT;
+ writel(value, port->base + RP_PRIV_MISC);
+
do {
unsigned int timeout = TEGRA_PCIE_LINKUP_TIMEOUT;
.has_pex_bias_ctrl = false,
.has_intr_prsnt_sense = false,
.has_cml_clk = false,
+ .has_gen2 = false,
};
static const struct tegra_pcie_soc_data tegra30_pcie_data = {
.has_pex_bias_ctrl = true,
.has_intr_prsnt_sense = true,
.has_cml_clk = true,
+ .has_gen2 = false,
+};
+
+static const struct tegra_pcie_soc_data tegra124_pcie_data = {
+ .num_ports = 2,
+ .msi_base_shift = 8,
+ .pads_pll_ctl = PADS_PLL_CTL_TEGRA30,
+ .tx_ref_sel = PADS_PLL_CTL_TXCLKREF_BUF_EN,
+ .has_pex_clkreq_en = true,
+ .has_pex_bias_ctrl = true,
+ .has_intr_prsnt_sense = true,
+ .has_cml_clk = true,
+ .has_gen2 = true,
};
static const struct of_device_id tegra_pcie_of_match[] = {
+ { .compatible = "nvidia,tegra124-pcie", .data = &tegra124_pcie_data },
{ .compatible = "nvidia,tegra30-pcie", .data = &tegra30_pcie_data },
{ .compatible = "nvidia,tegra20-pcie", .data = &tegra20_pcie_data },
{ },
static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
{
+ BUG_ON(!sys->private_data);
+
return sys->private_data;
}
int irq, pos0, pos1, i;
struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
- if (!pp) {
- BUG();
- return -EINVAL;
- }
-
pos0 = find_first_zero_bit(pp->msi_irq_in_use,
MAX_MSI_IRQS);
if (pos0 % no_irqs) {
/* get the port structure */
msi = irq_data_get_msi(data);
pp = sys_to_pcie(msi->dev->bus->sysdata);
- if (!pp) {
- BUG();
- return;
- }
/* undo what was done in assign_irq */
pos = data->hwirq;
struct msi_msg msg;
struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
- if (!pp) {
- BUG();
- return -EINVAL;
- }
-
pci_read_config_word(pdev, desc->msi_attrib.pos+PCI_MSI_FLAGS,
&msg_ctr);
msgvec = (msg_ctr&PCI_MSI_FLAGS_QSIZE) >> 4;
struct resource *cfg_res;
u32 val, na, ns;
const __be32 *addrp;
- int i, index;
+ int i, index, ret;
/* Find the address cell size and the number of cells in order to get
* the untranslated address.
cfg_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
if (cfg_res) {
- pp->config.cfg0_size = resource_size(cfg_res)/2;
- pp->config.cfg1_size = resource_size(cfg_res)/2;
+ pp->cfg0_size = resource_size(cfg_res)/2;
+ pp->cfg1_size = resource_size(cfg_res)/2;
pp->cfg0_base = cfg_res->start;
- pp->cfg1_base = cfg_res->start + pp->config.cfg0_size;
+ pp->cfg1_base = cfg_res->start + pp->cfg0_size;
/* Find the untranslated configuration space address */
index = of_property_match_string(np, "reg-names", "config");
addrp = of_get_address(np, index, false, false);
pp->cfg0_mod_base = of_read_number(addrp, ns);
- pp->cfg1_mod_base = pp->cfg0_mod_base + pp->config.cfg0_size;
+ pp->cfg1_mod_base = pp->cfg0_mod_base + pp->cfg0_size;
} else {
dev_err(pp->dev, "missing *config* reg space\n");
}
IO_SPACE_LIMIT,
range.pci_addr + range.size
+ global_io_offset);
- pp->config.io_size = resource_size(&pp->io);
- pp->config.io_bus_addr = range.pci_addr;
+ pp->io_size = resource_size(&pp->io);
+ pp->io_bus_addr = range.pci_addr;
pp->io_base = range.cpu_addr;
/* Find the untranslated IO space address */
if (restype == IORESOURCE_MEM) {
of_pci_range_to_resource(&range, np, &pp->mem);
pp->mem.name = "MEM";
- pp->config.mem_size = resource_size(&pp->mem);
- pp->config.mem_bus_addr = range.pci_addr;
+ pp->mem_size = resource_size(&pp->mem);
+ pp->mem_bus_addr = range.pci_addr;
/* Find the untranslated MEM space address */
pp->mem_mod_base = of_read_number(parser.range -
}
if (restype == 0) {
of_pci_range_to_resource(&range, np, &pp->cfg);
- pp->config.cfg0_size = resource_size(&pp->cfg)/2;
- pp->config.cfg1_size = resource_size(&pp->cfg)/2;
+ pp->cfg0_size = resource_size(&pp->cfg)/2;
+ pp->cfg1_size = resource_size(&pp->cfg)/2;
pp->cfg0_base = pp->cfg.start;
- pp->cfg1_base = pp->cfg.start + pp->config.cfg0_size;
+ pp->cfg1_base = pp->cfg.start + pp->cfg0_size;
/* Find the untranslated configuration space address */
pp->cfg0_mod_base = of_read_number(parser.range -
parser.np + na, ns);
pp->cfg1_mod_base = pp->cfg0_mod_base +
- pp->config.cfg0_size;
+ pp->cfg0_size;
}
}
+ ret = of_pci_parse_bus_range(np, &pp->busn);
+ if (ret < 0) {
+ pp->busn.name = np->name;
+ pp->busn.start = 0;
+ pp->busn.end = 0xff;
+ pp->busn.flags = IORESOURCE_BUS;
+ dev_dbg(pp->dev, "failed to parse bus-range property: %d, using default %pR\n",
+ ret, &pp->busn);
+ }
+
if (!pp->dbi_base) {
pp->dbi_base = devm_ioremap(pp->dev, pp->cfg.start,
resource_size(&pp->cfg));
pp->mem_base = pp->mem.start;
- pp->va_cfg0_base = devm_ioremap(pp->dev, pp->cfg0_base,
- pp->config.cfg0_size);
if (!pp->va_cfg0_base) {
- dev_err(pp->dev, "error with ioremap in function\n");
- return -ENOMEM;
+ pp->cfg0_base = pp->cfg.start;
+ pp->va_cfg0_base = devm_ioremap(pp->dev, pp->cfg0_base,
+ pp->cfg0_size);
+ if (!pp->va_cfg0_base) {
+ dev_err(pp->dev, "error with ioremap in function\n");
+ return -ENOMEM;
+ }
}
- pp->va_cfg1_base = devm_ioremap(pp->dev, pp->cfg1_base,
- pp->config.cfg1_size);
+
if (!pp->va_cfg1_base) {
- dev_err(pp->dev, "error with ioremap\n");
- return -ENOMEM;
+ pp->cfg1_base = pp->cfg.start + pp->cfg0_size;
+ pp->va_cfg1_base = devm_ioremap(pp->dev, pp->cfg1_base,
+ pp->cfg1_size);
+ if (!pp->va_cfg1_base) {
+ dev_err(pp->dev, "error with ioremap\n");
+ return -ENOMEM;
+ }
}
if (of_property_read_u32(np, "num-lanes", &pp->lanes)) {
}
if (IS_ENABLED(CONFIG_PCI_MSI)) {
- pp->irq_domain = irq_domain_add_linear(pp->dev->of_node,
- MAX_MSI_IRQS, &msi_domain_ops,
- &dw_pcie_msi_chip);
- if (!pp->irq_domain) {
- dev_err(pp->dev, "irq domain init failed\n");
- return -ENXIO;
- }
+ if (!pp->ops->msi_host_init) {
+ pp->irq_domain = irq_domain_add_linear(pp->dev->of_node,
+ MAX_MSI_IRQS, &msi_domain_ops,
+ &dw_pcie_msi_chip);
+ if (!pp->irq_domain) {
+ dev_err(pp->dev, "irq domain init failed\n");
+ return -ENXIO;
+ }
- for (i = 0; i < MAX_MSI_IRQS; i++)
- irq_create_mapping(pp->irq_domain, i);
+ for (i = 0; i < MAX_MSI_IRQS; i++)
+ irq_create_mapping(pp->irq_domain, i);
+ } else {
+ ret = pp->ops->msi_host_init(pp, &dw_pcie_msi_chip);
+ if (ret < 0)
+ return ret;
+ }
}
if (pp->ops->host_init)
dw_pci.private_data = (void **)&pp;
pci_common_init_dev(pp->dev, &dw_pci);
- pci_assign_unassigned_resources();
#ifdef CONFIG_PCI_DOMAINS
dw_pci.domain++;
#endif
PCIE_ATU_VIEWPORT);
dw_pcie_writel_rc(pp, pp->cfg0_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->cfg0_mod_base >> 32), PCIE_ATU_UPPER_BASE);
- dw_pcie_writel_rc(pp, pp->cfg0_mod_base + pp->config.cfg0_size - 1,
+ dw_pcie_writel_rc(pp, pp->cfg0_mod_base + pp->cfg0_size - 1,
PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG1, PCIE_ATU_CR1);
dw_pcie_writel_rc(pp, pp->cfg1_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->cfg1_mod_base >> 32), PCIE_ATU_UPPER_BASE);
- dw_pcie_writel_rc(pp, pp->cfg1_mod_base + pp->config.cfg1_size - 1,
+ dw_pcie_writel_rc(pp, pp->cfg1_mod_base + pp->cfg1_size - 1,
PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_MEM, PCIE_ATU_CR1);
dw_pcie_writel_rc(pp, pp->mem_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->mem_mod_base >> 32), PCIE_ATU_UPPER_BASE);
- dw_pcie_writel_rc(pp, pp->mem_mod_base + pp->config.mem_size - 1,
+ dw_pcie_writel_rc(pp, pp->mem_mod_base + pp->mem_size - 1,
PCIE_ATU_LIMIT);
- dw_pcie_writel_rc(pp, pp->config.mem_bus_addr, PCIE_ATU_LOWER_TARGET);
- dw_pcie_writel_rc(pp, upper_32_bits(pp->config.mem_bus_addr),
+ dw_pcie_writel_rc(pp, pp->mem_bus_addr, PCIE_ATU_LOWER_TARGET);
+ dw_pcie_writel_rc(pp, upper_32_bits(pp->mem_bus_addr),
PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
}
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_IO, PCIE_ATU_CR1);
dw_pcie_writel_rc(pp, pp->io_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->io_mod_base >> 32), PCIE_ATU_UPPER_BASE);
- dw_pcie_writel_rc(pp, pp->io_mod_base + pp->config.io_size - 1,
+ dw_pcie_writel_rc(pp, pp->io_mod_base + pp->io_size - 1,
PCIE_ATU_LIMIT);
- dw_pcie_writel_rc(pp, pp->config.io_bus_addr, PCIE_ATU_LOWER_TARGET);
- dw_pcie_writel_rc(pp, upper_32_bits(pp->config.io_bus_addr),
+ dw_pcie_writel_rc(pp, pp->io_bus_addr, PCIE_ATU_LOWER_TARGET);
+ dw_pcie_writel_rc(pp, upper_32_bits(pp->io_bus_addr),
PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
}
struct pcie_port *pp = sys_to_pcie(bus->sysdata);
int ret;
- if (!pp) {
- BUG();
- return -EINVAL;
- }
-
if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
*val = 0xffffffff;
return PCIBIOS_DEVICE_NOT_FOUND;
struct pcie_port *pp = sys_to_pcie(bus->sysdata);
int ret;
- if (!pp) {
- BUG();
- return -EINVAL;
- }
-
if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
return PCIBIOS_DEVICE_NOT_FOUND;
pp = sys_to_pcie(sys);
- if (!pp)
- return 0;
-
- if (global_io_offset < SZ_1M && pp->config.io_size > 0) {
- sys->io_offset = global_io_offset - pp->config.io_bus_addr;
+ if (global_io_offset < SZ_1M && pp->io_size > 0) {
+ sys->io_offset = global_io_offset - pp->io_bus_addr;
pci_ioremap_io(global_io_offset, pp->io_base);
global_io_offset += SZ_64K;
pci_add_resource_offset(&sys->resources, &pp->io,
sys->io_offset);
}
- sys->mem_offset = pp->mem.start - pp->config.mem_bus_addr;
+ sys->mem_offset = pp->mem.start - pp->mem_bus_addr;
pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
+ pci_add_resource(&sys->resources, &pp->busn);
return 1;
}
struct pci_bus *bus;
struct pcie_port *pp = sys_to_pcie(sys);
- if (pp) {
- pp->root_bus_nr = sys->busnr;
- bus = pci_scan_root_bus(pp->dev, sys->busnr, &dw_pcie_ops,
- sys, &sys->resources);
- } else {
- bus = NULL;
- BUG();
- }
+ pp->root_bus_nr = sys->busnr;
+ bus = pci_create_root_bus(pp->dev, sys->busnr,
+ &dw_pcie_ops, sys, &sys->resources);
+ if (!bus)
+ return NULL;
+
+ pci_scan_child_bus(bus);
+
+ if (bus && pp->ops->scan_bus)
+ pp->ops->scan_bus(pp);
return bus;
}
void dw_pcie_setup_rc(struct pcie_port *pp)
{
- struct pcie_port_info *config = &pp->config;
u32 val;
u32 membase;
u32 memlimit;
/* setup memory base, memory limit */
membase = ((u32)pp->mem_base & 0xfff00000) >> 16;
- memlimit = (config->mem_size + (u32)pp->mem_base) & 0xfff00000;
+ memlimit = (pp->mem_size + (u32)pp->mem_base) & 0xfff00000;
val = memlimit | membase;
dw_pcie_writel_rc(pp, val, PCI_MEMORY_BASE);
#ifndef _PCIE_DESIGNWARE_H
#define _PCIE_DESIGNWARE_H
-struct pcie_port_info {
- u32 cfg0_size;
- u32 cfg1_size;
- u32 io_size;
- u32 mem_size;
- phys_addr_t io_bus_addr;
- phys_addr_t mem_bus_addr;
-};
-
/*
* Maximum number of MSI IRQs can be 256 per controller. But keep
* it 32 as of now. Probably we will never need more than 32. If needed,
u64 cfg0_base;
u64 cfg0_mod_base;
void __iomem *va_cfg0_base;
+ u32 cfg0_size;
u64 cfg1_base;
u64 cfg1_mod_base;
void __iomem *va_cfg1_base;
+ u32 cfg1_size;
u64 io_base;
u64 io_mod_base;
+ phys_addr_t io_bus_addr;
+ u32 io_size;
u64 mem_base;
u64 mem_mod_base;
+ phys_addr_t mem_bus_addr;
+ u32 mem_size;
struct resource cfg;
struct resource io;
struct resource mem;
- struct pcie_port_info config;
+ struct resource busn;
int irq;
u32 lanes;
struct pcie_host_ops *ops;
void (*msi_set_irq)(struct pcie_port *pp, int irq);
void (*msi_clear_irq)(struct pcie_port *pp, int irq);
u32 (*get_msi_data)(struct pcie_port *pp);
+ void (*scan_bus)(struct pcie_port *pp);
+ int (*msi_host_init)(struct pcie_port *pp, struct msi_chip *chip);
};
int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val);
pp->dev = dev;
- dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ dbi_base = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
pp->dbi_base = devm_ioremap_resource(dev, dbi_base);
if (IS_ERR(pp->dbi_base)) {
dev_err(dev, "couldn't remap dbi base %p\n", dbi_base);
--- /dev/null
+/*
+ * PCIe host controller driver for Xilinx AXI PCIe Bridge
+ *
+ * Copyright (c) 2012 - 2014 Xilinx, Inc.
+ *
+ * Based on the Tegra PCIe driver
+ *
+ * Bits taken from Synopsys Designware Host controller driver and
+ * ARM PCI Host generic driver.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+
+/* Register definitions */
+#define XILINX_PCIE_REG_BIR 0x00000130
+#define XILINX_PCIE_REG_IDR 0x00000138
+#define XILINX_PCIE_REG_IMR 0x0000013c
+#define XILINX_PCIE_REG_PSCR 0x00000144
+#define XILINX_PCIE_REG_RPSC 0x00000148
+#define XILINX_PCIE_REG_MSIBASE1 0x0000014c
+#define XILINX_PCIE_REG_MSIBASE2 0x00000150
+#define XILINX_PCIE_REG_RPEFR 0x00000154
+#define XILINX_PCIE_REG_RPIFR1 0x00000158
+#define XILINX_PCIE_REG_RPIFR2 0x0000015c
+
+/* Interrupt registers definitions */
+#define XILINX_PCIE_INTR_LINK_DOWN BIT(0)
+#define XILINX_PCIE_INTR_ECRC_ERR BIT(1)
+#define XILINX_PCIE_INTR_STR_ERR BIT(2)
+#define XILINX_PCIE_INTR_HOT_RESET BIT(3)
+#define XILINX_PCIE_INTR_CFG_TIMEOUT BIT(8)
+#define XILINX_PCIE_INTR_CORRECTABLE BIT(9)
+#define XILINX_PCIE_INTR_NONFATAL BIT(10)
+#define XILINX_PCIE_INTR_FATAL BIT(11)
+#define XILINX_PCIE_INTR_INTX BIT(16)
+#define XILINX_PCIE_INTR_MSI BIT(17)
+#define XILINX_PCIE_INTR_SLV_UNSUPP BIT(20)
+#define XILINX_PCIE_INTR_SLV_UNEXP BIT(21)
+#define XILINX_PCIE_INTR_SLV_COMPL BIT(22)
+#define XILINX_PCIE_INTR_SLV_ERRP BIT(23)
+#define XILINX_PCIE_INTR_SLV_CMPABT BIT(24)
+#define XILINX_PCIE_INTR_SLV_ILLBUR BIT(25)
+#define XILINX_PCIE_INTR_MST_DECERR BIT(26)
+#define XILINX_PCIE_INTR_MST_SLVERR BIT(27)
+#define XILINX_PCIE_INTR_MST_ERRP BIT(28)
+#define XILINX_PCIE_IMR_ALL_MASK 0x1FF30FED
+#define XILINX_PCIE_IDR_ALL_MASK 0xFFFFFFFF
+
+/* Root Port Error FIFO Read Register definitions */
+#define XILINX_PCIE_RPEFR_ERR_VALID BIT(18)
+#define XILINX_PCIE_RPEFR_REQ_ID GENMASK(15, 0)
+#define XILINX_PCIE_RPEFR_ALL_MASK 0xFFFFFFFF
+
+/* Root Port Interrupt FIFO Read Register 1 definitions */
+#define XILINX_PCIE_RPIFR1_INTR_VALID BIT(31)
+#define XILINX_PCIE_RPIFR1_MSI_INTR BIT(30)
+#define XILINX_PCIE_RPIFR1_INTR_MASK GENMASK(28, 27)
+#define XILINX_PCIE_RPIFR1_ALL_MASK 0xFFFFFFFF
+#define XILINX_PCIE_RPIFR1_INTR_SHIFT 27
+
+/* Bridge Info Register definitions */
+#define XILINX_PCIE_BIR_ECAM_SZ_MASK GENMASK(18, 16)
+#define XILINX_PCIE_BIR_ECAM_SZ_SHIFT 16
+
+/* Root Port Interrupt FIFO Read Register 2 definitions */
+#define XILINX_PCIE_RPIFR2_MSG_DATA GENMASK(15, 0)
+
+/* Root Port Status/control Register definitions */
+#define XILINX_PCIE_REG_RPSC_BEN BIT(0)
+
+/* Phy Status/Control Register definitions */
+#define XILINX_PCIE_REG_PSCR_LNKUP BIT(11)
+
+/* ECAM definitions */
+#define ECAM_BUS_NUM_SHIFT 20
+#define ECAM_DEV_NUM_SHIFT 12
+
+/* Number of MSI IRQs */
+#define XILINX_NUM_MSI_IRQS 128
+
+/* Number of Memory Resources */
+#define XILINX_MAX_NUM_RESOURCES 3
+
+/**
+ * struct xilinx_pcie_port - PCIe port information
+ * @reg_base: IO Mapped Register Base
+ * @irq: Interrupt number
+ * @msi_pages: MSI pages
+ * @root_busno: Root Bus number
+ * @dev: Device pointer
+ * @irq_domain: IRQ domain pointer
+ * @bus_range: Bus range
+ * @resources: Bus Resources
+ */
+struct xilinx_pcie_port {
+ void __iomem *reg_base;
+ u32 irq;
+ unsigned long msi_pages;
+ u8 root_busno;
+ struct device *dev;
+ struct irq_domain *irq_domain;
+ struct resource bus_range;
+ struct list_head resources;
+};
+
+static DECLARE_BITMAP(msi_irq_in_use, XILINX_NUM_MSI_IRQS);
+
+static inline struct xilinx_pcie_port *sys_to_pcie(struct pci_sys_data *sys)
+{
+ return sys->private_data;
+}
+
+static inline u32 pcie_read(struct xilinx_pcie_port *port, u32 reg)
+{
+ return readl(port->reg_base + reg);
+}
+
+static inline void pcie_write(struct xilinx_pcie_port *port, u32 val, u32 reg)
+{
+ writel(val, port->reg_base + reg);
+}
+
+static inline bool xilinx_pcie_link_is_up(struct xilinx_pcie_port *port)
+{
+ return (pcie_read(port, XILINX_PCIE_REG_PSCR) &
+ XILINX_PCIE_REG_PSCR_LNKUP) ? 1 : 0;
+}
+
+/**
+ * xilinx_pcie_clear_err_interrupts - Clear Error Interrupts
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_clear_err_interrupts(struct xilinx_pcie_port *port)
+{
+ u32 val = pcie_read(port, XILINX_PCIE_REG_RPEFR);
+
+ if (val & XILINX_PCIE_RPEFR_ERR_VALID) {
+ dev_dbg(port->dev, "Requester ID %d\n",
+ val & XILINX_PCIE_RPEFR_REQ_ID);
+ pcie_write(port, XILINX_PCIE_RPEFR_ALL_MASK,
+ XILINX_PCIE_REG_RPEFR);
+ }
+}
+
+/**
+ * xilinx_pcie_valid_device - Check if a valid device is present on bus
+ * @bus: PCI Bus structure
+ * @devfn: device/function
+ *
+ * Return: 'true' on success and 'false' if invalid device is found
+ */
+static bool xilinx_pcie_valid_device(struct pci_bus *bus, unsigned int devfn)
+{
+ struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
+
+ /* Check if link is up when trying to access downstream ports */
+ if (bus->number != port->root_busno)
+ if (!xilinx_pcie_link_is_up(port))
+ return false;
+
+ /* Only one device down on each root port */
+ if (bus->number == port->root_busno && devfn > 0)
+ return false;
+
+ /*
+ * Do not read more than one device on the bus directly attached
+ * to RC.
+ */
+ if (bus->primary == port->root_busno && devfn > 0)
+ return false;
+
+ return true;
+}
+
+/**
+ * xilinx_pcie_config_base - Get configuration base
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ *
+ * Return: Base address of the configuration space needed to be
+ * accessed.
+ */
+static void __iomem *xilinx_pcie_config_base(struct pci_bus *bus,
+ unsigned int devfn, int where)
+{
+ struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
+ int relbus;
+
+ relbus = (bus->number << ECAM_BUS_NUM_SHIFT) |
+ (devfn << ECAM_DEV_NUM_SHIFT);
+
+ return port->reg_base + relbus + where;
+}
+
+/**
+ * xilinx_pcie_read_config - Read configuration space
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ * @size: Byte/word/dword
+ * @val: Value to be read
+ *
+ * Return: PCIBIOS_SUCCESSFUL on success
+ * PCIBIOS_DEVICE_NOT_FOUND on failure
+ */
+static int xilinx_pcie_read_config(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ void __iomem *addr;
+
+ if (!xilinx_pcie_valid_device(bus, devfn)) {
+ *val = 0xFFFFFFFF;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
+ addr = xilinx_pcie_config_base(bus, devfn, where);
+
+ switch (size) {
+ case 1:
+ *val = readb(addr);
+ break;
+ case 2:
+ *val = readw(addr);
+ break;
+ default:
+ *val = readl(addr);
+ break;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/**
+ * xilinx_pcie_write_config - Write configuration space
+ * @bus: PCI Bus structure
+ * @devfn: Device/function
+ * @where: Offset from base
+ * @size: Byte/word/dword
+ * @val: Value to be written to device
+ *
+ * Return: PCIBIOS_SUCCESSFUL on success
+ * PCIBIOS_DEVICE_NOT_FOUND on failure
+ */
+static int xilinx_pcie_write_config(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ void __iomem *addr;
+
+ if (!xilinx_pcie_valid_device(bus, devfn))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ addr = xilinx_pcie_config_base(bus, devfn, where);
+
+ switch (size) {
+ case 1:
+ writeb(val, addr);
+ break;
+ case 2:
+ writew(val, addr);
+ break;
+ default:
+ writel(val, addr);
+ break;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/* PCIe operations */
+static struct pci_ops xilinx_pcie_ops = {
+ .read = xilinx_pcie_read_config,
+ .write = xilinx_pcie_write_config,
+};
+
+/* MSI functions */
+
+/**
+ * xilinx_pcie_destroy_msi - Free MSI number
+ * @irq: IRQ to be freed
+ */
+static void xilinx_pcie_destroy_msi(unsigned int irq)
+{
+ struct irq_desc *desc;
+ struct msi_desc *msi;
+ struct xilinx_pcie_port *port;
+
+ desc = irq_to_desc(irq);
+ msi = irq_desc_get_msi_desc(desc);
+ port = sys_to_pcie(msi->dev->bus->sysdata);
+
+ if (!test_bit(irq, msi_irq_in_use))
+ dev_err(port->dev, "Trying to free unused MSI#%d\n", irq);
+ else
+ clear_bit(irq, msi_irq_in_use);
+}
+
+/**
+ * xilinx_pcie_assign_msi - Allocate MSI number
+ * @port: PCIe port structure
+ *
+ * Return: A valid IRQ on success and error value on failure.
+ */
+static int xilinx_pcie_assign_msi(struct xilinx_pcie_port *port)
+{
+ int pos;
+
+ pos = find_first_zero_bit(msi_irq_in_use, XILINX_NUM_MSI_IRQS);
+ if (pos < XILINX_NUM_MSI_IRQS)
+ set_bit(pos, msi_irq_in_use);
+ else
+ return -ENOSPC;
+
+ return pos;
+}
+
+/**
+ * xilinx_msi_teardown_irq - Destroy the MSI
+ * @chip: MSI Chip descriptor
+ * @irq: MSI IRQ to destroy
+ */
+static void xilinx_msi_teardown_irq(struct msi_chip *chip, unsigned int irq)
+{
+ xilinx_pcie_destroy_msi(irq);
+}
+
+/**
+ * xilinx_pcie_msi_setup_irq - Setup MSI request
+ * @chip: MSI chip pointer
+ * @pdev: PCIe device pointer
+ * @desc: MSI descriptor pointer
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_msi_setup_irq(struct msi_chip *chip,
+ struct pci_dev *pdev,
+ struct msi_desc *desc)
+{
+ struct xilinx_pcie_port *port = sys_to_pcie(pdev->bus->sysdata);
+ unsigned int irq;
+ int hwirq;
+ struct msi_msg msg;
+ phys_addr_t msg_addr;
+
+ hwirq = xilinx_pcie_assign_msi(port);
+ if (hwirq < 0)
+ return hwirq;
+
+ irq = irq_create_mapping(port->irq_domain, hwirq);
+ if (!irq)
+ return -EINVAL;
+
+ irq_set_msi_desc(irq, desc);
+
+ msg_addr = virt_to_phys((void *)port->msi_pages);
+
+ msg.address_hi = 0;
+ msg.address_lo = msg_addr;
+ msg.data = irq;
+
+ write_msi_msg(irq, &msg);
+
+ return 0;
+}
+
+/* MSI Chip Descriptor */
+static struct msi_chip xilinx_pcie_msi_chip = {
+ .setup_irq = xilinx_pcie_msi_setup_irq,
+ .teardown_irq = xilinx_msi_teardown_irq,
+};
+
+/* HW Interrupt Chip Descriptor */
+static struct irq_chip xilinx_msi_irq_chip = {
+ .name = "Xilinx PCIe MSI",
+ .irq_enable = unmask_msi_irq,
+ .irq_disable = mask_msi_irq,
+ .irq_mask = mask_msi_irq,
+ .irq_unmask = unmask_msi_irq,
+};
+
+/**
+ * xilinx_pcie_msi_map - Set the handler for the MSI and mark IRQ as valid
+ * @domain: IRQ domain
+ * @irq: Virtual IRQ number
+ * @hwirq: HW interrupt number
+ *
+ * Return: Always returns 0.
+ */
+static int xilinx_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_and_handler(irq, &xilinx_msi_irq_chip, handle_simple_irq);
+ irq_set_chip_data(irq, domain->host_data);
+ set_irq_flags(irq, IRQF_VALID);
+
+ return 0;
+}
+
+/* IRQ Domain operations */
+static const struct irq_domain_ops msi_domain_ops = {
+ .map = xilinx_pcie_msi_map,
+};
+
+/**
+ * xilinx_pcie_enable_msi - Enable MSI support
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_enable_msi(struct xilinx_pcie_port *port)
+{
+ phys_addr_t msg_addr;
+
+ port->msi_pages = __get_free_pages(GFP_KERNEL, 0);
+ msg_addr = virt_to_phys((void *)port->msi_pages);
+ pcie_write(port, 0x0, XILINX_PCIE_REG_MSIBASE1);
+ pcie_write(port, msg_addr, XILINX_PCIE_REG_MSIBASE2);
+}
+
+/**
+ * xilinx_pcie_add_bus - Add MSI chip info to PCIe bus
+ * @bus: PCIe bus
+ */
+static void xilinx_pcie_add_bus(struct pci_bus *bus)
+{
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ struct xilinx_pcie_port *port = sys_to_pcie(bus->sysdata);
+
+ xilinx_pcie_msi_chip.dev = port->dev;
+ bus->msi = &xilinx_pcie_msi_chip;
+ }
+}
+
+/* INTx Functions */
+
+/**
+ * xilinx_pcie_intx_map - Set the handler for the INTx and mark IRQ as valid
+ * @domain: IRQ domain
+ * @irq: Virtual IRQ number
+ * @hwirq: HW interrupt number
+ *
+ * Return: Always returns 0.
+ */
+static int xilinx_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);
+ irq_set_chip_data(irq, domain->host_data);
+ set_irq_flags(irq, IRQF_VALID);
+
+ return 0;
+}
+
+/* INTx IRQ Domain operations */
+static const struct irq_domain_ops intx_domain_ops = {
+ .map = xilinx_pcie_intx_map,
+};
+
+/* PCIe HW Functions */
+
+/**
+ * xilinx_pcie_intr_handler - Interrupt Service Handler
+ * @irq: IRQ number
+ * @data: PCIe port information
+ *
+ * Return: IRQ_HANDLED on success and IRQ_NONE on failure
+ */
+static irqreturn_t xilinx_pcie_intr_handler(int irq, void *data)
+{
+ struct xilinx_pcie_port *port = (struct xilinx_pcie_port *)data;
+ u32 val, mask, status, msi_data;
+
+ /* Read interrupt decode and mask registers */
+ val = pcie_read(port, XILINX_PCIE_REG_IDR);
+ mask = pcie_read(port, XILINX_PCIE_REG_IMR);
+
+ status = val & mask;
+ if (!status)
+ return IRQ_NONE;
+
+ if (status & XILINX_PCIE_INTR_LINK_DOWN)
+ dev_warn(port->dev, "Link Down\n");
+
+ if (status & XILINX_PCIE_INTR_ECRC_ERR)
+ dev_warn(port->dev, "ECRC failed\n");
+
+ if (status & XILINX_PCIE_INTR_STR_ERR)
+ dev_warn(port->dev, "Streaming error\n");
+
+ if (status & XILINX_PCIE_INTR_HOT_RESET)
+ dev_info(port->dev, "Hot reset\n");
+
+ if (status & XILINX_PCIE_INTR_CFG_TIMEOUT)
+ dev_warn(port->dev, "ECAM access timeout\n");
+
+ if (status & XILINX_PCIE_INTR_CORRECTABLE) {
+ dev_warn(port->dev, "Correctable error message\n");
+ xilinx_pcie_clear_err_interrupts(port);
+ }
+
+ if (status & XILINX_PCIE_INTR_NONFATAL) {
+ dev_warn(port->dev, "Non fatal error message\n");
+ xilinx_pcie_clear_err_interrupts(port);
+ }
+
+ if (status & XILINX_PCIE_INTR_FATAL) {
+ dev_warn(port->dev, "Fatal error message\n");
+ xilinx_pcie_clear_err_interrupts(port);
+ }
+
+ if (status & XILINX_PCIE_INTR_INTX) {
+ /* INTx interrupt received */
+ val = pcie_read(port, XILINX_PCIE_REG_RPIFR1);
+
+ /* Check whether interrupt valid */
+ if (!(val & XILINX_PCIE_RPIFR1_INTR_VALID)) {
+ dev_warn(port->dev, "RP Intr FIFO1 read error\n");
+ return IRQ_HANDLED;
+ }
+
+ /* Clear interrupt FIFO register 1 */
+ pcie_write(port, XILINX_PCIE_RPIFR1_ALL_MASK,
+ XILINX_PCIE_REG_RPIFR1);
+
+ /* Handle INTx Interrupt */
+ val = ((val & XILINX_PCIE_RPIFR1_INTR_MASK) >>
+ XILINX_PCIE_RPIFR1_INTR_SHIFT) + 1;
+ generic_handle_irq(irq_find_mapping(port->irq_domain, val));
+ }
+
+ if (status & XILINX_PCIE_INTR_MSI) {
+ /* MSI Interrupt */
+ val = pcie_read(port, XILINX_PCIE_REG_RPIFR1);
+
+ if (!(val & XILINX_PCIE_RPIFR1_INTR_VALID)) {
+ dev_warn(port->dev, "RP Intr FIFO1 read error\n");
+ return IRQ_HANDLED;
+ }
+
+ if (val & XILINX_PCIE_RPIFR1_MSI_INTR) {
+ msi_data = pcie_read(port, XILINX_PCIE_REG_RPIFR2) &
+ XILINX_PCIE_RPIFR2_MSG_DATA;
+
+ /* Clear interrupt FIFO register 1 */
+ pcie_write(port, XILINX_PCIE_RPIFR1_ALL_MASK,
+ XILINX_PCIE_REG_RPIFR1);
+
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ /* Handle MSI Interrupt */
+ generic_handle_irq(msi_data);
+ }
+ }
+ }
+
+ if (status & XILINX_PCIE_INTR_SLV_UNSUPP)
+ dev_warn(port->dev, "Slave unsupported request\n");
+
+ if (status & XILINX_PCIE_INTR_SLV_UNEXP)
+ dev_warn(port->dev, "Slave unexpected completion\n");
+
+ if (status & XILINX_PCIE_INTR_SLV_COMPL)
+ dev_warn(port->dev, "Slave completion timeout\n");
+
+ if (status & XILINX_PCIE_INTR_SLV_ERRP)
+ dev_warn(port->dev, "Slave Error Poison\n");
+
+ if (status & XILINX_PCIE_INTR_SLV_CMPABT)
+ dev_warn(port->dev, "Slave Completer Abort\n");
+
+ if (status & XILINX_PCIE_INTR_SLV_ILLBUR)
+ dev_warn(port->dev, "Slave Illegal Burst\n");
+
+ if (status & XILINX_PCIE_INTR_MST_DECERR)
+ dev_warn(port->dev, "Master decode error\n");
+
+ if (status & XILINX_PCIE_INTR_MST_SLVERR)
+ dev_warn(port->dev, "Master slave error\n");
+
+ if (status & XILINX_PCIE_INTR_MST_ERRP)
+ dev_warn(port->dev, "Master error poison\n");
+
+ /* Clear the Interrupt Decode register */
+ pcie_write(port, status, XILINX_PCIE_REG_IDR);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * xilinx_pcie_free_irq_domain - Free IRQ domain
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_free_irq_domain(struct xilinx_pcie_port *port)
+{
+ int i;
+ u32 irq, num_irqs;
+
+ /* Free IRQ Domain */
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+
+ free_pages(port->msi_pages, 0);
+
+ num_irqs = XILINX_NUM_MSI_IRQS;
+ } else {
+ /* INTx */
+ num_irqs = 4;
+ }
+
+ for (i = 0; i < num_irqs; i++) {
+ irq = irq_find_mapping(port->irq_domain, i);
+ if (irq > 0)
+ irq_dispose_mapping(irq);
+ }
+
+ irq_domain_remove(port->irq_domain);
+}
+
+/**
+ * xilinx_pcie_init_irq_domain - Initialize IRQ domain
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_init_irq_domain(struct xilinx_pcie_port *port)
+{
+ struct device *dev = port->dev;
+ struct device_node *node = dev->of_node;
+ struct device_node *pcie_intc_node;
+
+ /* Setup INTx */
+ pcie_intc_node = of_get_next_child(node, NULL);
+ if (!pcie_intc_node) {
+ dev_err(dev, "No PCIe Intc node found\n");
+ return PTR_ERR(pcie_intc_node);
+ }
+
+ port->irq_domain = irq_domain_add_linear(pcie_intc_node, 4,
+ &intx_domain_ops,
+ port);
+ if (!port->irq_domain) {
+ dev_err(dev, "Failed to get a INTx IRQ domain\n");
+ return PTR_ERR(port->irq_domain);
+ }
+
+ /* Setup MSI */
+ if (IS_ENABLED(CONFIG_PCI_MSI)) {
+ port->irq_domain = irq_domain_add_linear(node,
+ XILINX_NUM_MSI_IRQS,
+ &msi_domain_ops,
+ &xilinx_pcie_msi_chip);
+ if (!port->irq_domain) {
+ dev_err(dev, "Failed to get a MSI IRQ domain\n");
+ return PTR_ERR(port->irq_domain);
+ }
+
+ xilinx_pcie_enable_msi(port);
+ }
+
+ return 0;
+}
+
+/**
+ * xilinx_pcie_init_port - Initialize hardware
+ * @port: PCIe port information
+ */
+static void xilinx_pcie_init_port(struct xilinx_pcie_port *port)
+{
+ if (xilinx_pcie_link_is_up(port))
+ dev_info(port->dev, "PCIe Link is UP\n");
+ else
+ dev_info(port->dev, "PCIe Link is DOWN\n");
+
+ /* Disable all interrupts */
+ pcie_write(port, ~XILINX_PCIE_IDR_ALL_MASK,
+ XILINX_PCIE_REG_IMR);
+
+ /* Clear pending interrupts */
+ pcie_write(port, pcie_read(port, XILINX_PCIE_REG_IDR) &
+ XILINX_PCIE_IMR_ALL_MASK,
+ XILINX_PCIE_REG_IDR);
+
+ /* Enable all interrupts */
+ pcie_write(port, XILINX_PCIE_IMR_ALL_MASK, XILINX_PCIE_REG_IMR);
+
+ /* Enable the Bridge enable bit */
+ pcie_write(port, pcie_read(port, XILINX_PCIE_REG_RPSC) |
+ XILINX_PCIE_REG_RPSC_BEN,
+ XILINX_PCIE_REG_RPSC);
+}
+
+/**
+ * xilinx_pcie_setup - Setup memory resources
+ * @nr: Bus number
+ * @sys: Per controller structure
+ *
+ * Return: '1' on success and error value on failure
+ */
+static int xilinx_pcie_setup(int nr, struct pci_sys_data *sys)
+{
+ struct xilinx_pcie_port *port = sys_to_pcie(sys);
+
+ list_splice_init(&port->resources, &sys->resources);
+
+ return 1;
+}
+
+/**
+ * xilinx_pcie_scan_bus - Scan PCIe bus for devices
+ * @nr: Bus number
+ * @sys: Per controller structure
+ *
+ * Return: Valid Bus pointer on success and NULL on failure
+ */
+static struct pci_bus *xilinx_pcie_scan_bus(int nr, struct pci_sys_data *sys)
+{
+ struct xilinx_pcie_port *port = sys_to_pcie(sys);
+ struct pci_bus *bus;
+
+ port->root_busno = sys->busnr;
+ bus = pci_scan_root_bus(port->dev, sys->busnr, &xilinx_pcie_ops,
+ sys, &sys->resources);
+
+ return bus;
+}
+
+/**
+ * xilinx_pcie_parse_and_add_res - Add resources by parsing ranges
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_parse_and_add_res(struct xilinx_pcie_port *port)
+{
+ struct device *dev = port->dev;
+ struct device_node *node = dev->of_node;
+ struct resource *mem;
+ resource_size_t offset;
+ struct of_pci_range_parser parser;
+ struct of_pci_range range;
+ struct pci_host_bridge_window *win;
+ int err = 0, mem_resno = 0;
+
+ /* Get the ranges */
+ if (of_pci_range_parser_init(&parser, node)) {
+ dev_err(dev, "missing \"ranges\" property\n");
+ return -EINVAL;
+ }
+
+ /* Parse the ranges and add the resources found to the list */
+ for_each_of_pci_range(&parser, &range) {
+
+ if (mem_resno >= XILINX_MAX_NUM_RESOURCES) {
+ dev_err(dev, "Maximum memory resources exceeded\n");
+ return -EINVAL;
+ }
+
+ mem = devm_kmalloc(dev, sizeof(*mem), GFP_KERNEL);
+ if (!mem) {
+ err = -ENOMEM;
+ goto free_resources;
+ }
+
+ of_pci_range_to_resource(&range, node, mem);
+
+ switch (mem->flags & IORESOURCE_TYPE_BITS) {
+ case IORESOURCE_MEM:
+ offset = range.cpu_addr - range.pci_addr;
+ mem_resno++;
+ break;
+ default:
+ err = -EINVAL;
+ break;
+ }
+
+ if (err < 0) {
+ dev_warn(dev, "Invalid resource found %pR\n", mem);
+ continue;
+ }
+
+ err = request_resource(&iomem_resource, mem);
+ if (err)
+ goto free_resources;
+
+ pci_add_resource_offset(&port->resources, mem, offset);
+ }
+
+ /* Get the bus range */
+ if (of_pci_parse_bus_range(node, &port->bus_range)) {
+ u32 val = pcie_read(port, XILINX_PCIE_REG_BIR);
+ u8 last;
+
+ last = (val & XILINX_PCIE_BIR_ECAM_SZ_MASK) >>
+ XILINX_PCIE_BIR_ECAM_SZ_SHIFT;
+
+ port->bus_range = (struct resource) {
+ .name = node->name,
+ .start = 0,
+ .end = last,
+ .flags = IORESOURCE_BUS,
+ };
+ }
+
+ /* Register bus resource */
+ pci_add_resource(&port->resources, &port->bus_range);
+
+ return 0;
+
+free_resources:
+ release_child_resources(&iomem_resource);
+ list_for_each_entry(win, &port->resources, list)
+ devm_kfree(dev, win->res);
+ pci_free_resource_list(&port->resources);
+
+ return err;
+}
+
+/**
+ * xilinx_pcie_parse_dt - Parse Device tree
+ * @port: PCIe port information
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_parse_dt(struct xilinx_pcie_port *port)
+{
+ struct device *dev = port->dev;
+ struct device_node *node = dev->of_node;
+ struct resource regs;
+ const char *type;
+ int err;
+
+ type = of_get_property(node, "device_type", NULL);
+ if (!type || strcmp(type, "pci")) {
+ dev_err(dev, "invalid \"device_type\" %s\n", type);
+ return -EINVAL;
+ }
+
+ err = of_address_to_resource(node, 0, ®s);
+ if (err) {
+ dev_err(dev, "missing \"reg\" property\n");
+ return err;
+ }
+
+ port->reg_base = devm_ioremap_resource(dev, ®s);
+ if (IS_ERR(port->reg_base))
+ return PTR_ERR(port->reg_base);
+
+ port->irq = irq_of_parse_and_map(node, 0);
+ err = devm_request_irq(dev, port->irq, xilinx_pcie_intr_handler,
+ IRQF_SHARED, "xilinx-pcie", port);
+ if (err) {
+ dev_err(dev, "unable to request irq %d\n", port->irq);
+ return err;
+ }
+
+ return 0;
+}
+
+/**
+ * xilinx_pcie_probe - Probe function
+ * @pdev: Platform device pointer
+ *
+ * Return: '0' on success and error value on failure
+ */
+static int xilinx_pcie_probe(struct platform_device *pdev)
+{
+ struct xilinx_pcie_port *port;
+ struct hw_pci hw;
+ struct device *dev = &pdev->dev;
+ int err;
+
+ if (!dev->of_node)
+ return -ENODEV;
+
+ port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+ if (!port)
+ return -ENOMEM;
+
+ port->dev = dev;
+
+ err = xilinx_pcie_parse_dt(port);
+ if (err) {
+ dev_err(dev, "Parsing DT failed\n");
+ return err;
+ }
+
+ xilinx_pcie_init_port(port);
+
+ err = xilinx_pcie_init_irq_domain(port);
+ if (err) {
+ dev_err(dev, "Failed creating IRQ Domain\n");
+ return err;
+ }
+
+ /*
+ * Parse PCI ranges, configuration bus range and
+ * request their resources
+ */
+ INIT_LIST_HEAD(&port->resources);
+ err = xilinx_pcie_parse_and_add_res(port);
+ if (err) {
+ dev_err(dev, "Failed adding resources\n");
+ return err;
+ }
+
+ platform_set_drvdata(pdev, port);
+
+ /* Register the device */
+ memset(&hw, 0, sizeof(hw));
+ hw = (struct hw_pci) {
+ .nr_controllers = 1,
+ .private_data = (void **)&port,
+ .setup = xilinx_pcie_setup,
+ .map_irq = of_irq_parse_and_map_pci,
+ .add_bus = xilinx_pcie_add_bus,
+ .scan = xilinx_pcie_scan_bus,
+ .ops = &xilinx_pcie_ops,
+ };
+ pci_common_init_dev(dev, &hw);
+
+ return 0;
+}
+
+/**
+ * xilinx_pcie_remove - Remove function
+ * @pdev: Platform device pointer
+ *
+ * Return: '0' always
+ */
+static int xilinx_pcie_remove(struct platform_device *pdev)
+{
+ struct xilinx_pcie_port *port = platform_get_drvdata(pdev);
+
+ xilinx_pcie_free_irq_domain(port);
+
+ return 0;
+}
+
+static struct of_device_id xilinx_pcie_of_match[] = {
+ { .compatible = "xlnx,axi-pcie-host-1.00.a", },
+ {}
+};
+
+static struct platform_driver xilinx_pcie_driver = {
+ .driver = {
+ .name = "xilinx-pcie",
+ .owner = THIS_MODULE,
+ .of_match_table = xilinx_pcie_of_match,
+ .suppress_bind_attrs = true,
+ },
+ .probe = xilinx_pcie_probe,
+ .remove = xilinx_pcie_remove,
+};
+module_platform_driver(xilinx_pcie_driver);
+
+MODULE_AUTHOR("Xilinx Inc");
+MODULE_DESCRIPTION("Xilinx AXI PCIe driver");
+MODULE_LICENSE("GPL v2");
obj-$(CONFIG_HOTPLUG_PCI_ACPI_IBM) += acpiphp_ibm.o
-pci_hotplug-objs := pci_hotplug_core.o pcihp_slot.o
+pci_hotplug-objs := pci_hotplug_core.o
ifdef CONFIG_HOTPLUG_PCI_CPCI
pci_hotplug-objs += cpci_hotplug_core.o \
static bool debug_acpi;
-static acpi_status
-decode_type0_hpx_record(union acpi_object *record, struct hotplug_params *hpx)
-{
- int i;
- union acpi_object *fields = record->package.elements;
- u32 revision = fields[1].integer.value;
-
- switch (revision) {
- case 1:
- if (record->package.count != 6)
- return AE_ERROR;
- for (i = 2; i < 6; i++)
- if (fields[i].type != ACPI_TYPE_INTEGER)
- return AE_ERROR;
- hpx->t0 = &hpx->type0_data;
- hpx->t0->revision = revision;
- hpx->t0->cache_line_size = fields[2].integer.value;
- hpx->t0->latency_timer = fields[3].integer.value;
- hpx->t0->enable_serr = fields[4].integer.value;
- hpx->t0->enable_perr = fields[5].integer.value;
- break;
- default:
- printk(KERN_WARNING
- "%s: Type 0 Revision %d record not supported\n",
- __func__, revision);
- return AE_ERROR;
- }
- return AE_OK;
-}
-
-static acpi_status
-decode_type1_hpx_record(union acpi_object *record, struct hotplug_params *hpx)
-{
- int i;
- union acpi_object *fields = record->package.elements;
- u32 revision = fields[1].integer.value;
-
- switch (revision) {
- case 1:
- if (record->package.count != 5)
- return AE_ERROR;
- for (i = 2; i < 5; i++)
- if (fields[i].type != ACPI_TYPE_INTEGER)
- return AE_ERROR;
- hpx->t1 = &hpx->type1_data;
- hpx->t1->revision = revision;
- hpx->t1->max_mem_read = fields[2].integer.value;
- hpx->t1->avg_max_split = fields[3].integer.value;
- hpx->t1->tot_max_split = fields[4].integer.value;
- break;
- default:
- printk(KERN_WARNING
- "%s: Type 1 Revision %d record not supported\n",
- __func__, revision);
- return AE_ERROR;
- }
- return AE_OK;
-}
-
-static acpi_status
-decode_type2_hpx_record(union acpi_object *record, struct hotplug_params *hpx)
-{
- int i;
- union acpi_object *fields = record->package.elements;
- u32 revision = fields[1].integer.value;
-
- switch (revision) {
- case 1:
- if (record->package.count != 18)
- return AE_ERROR;
- for (i = 2; i < 18; i++)
- if (fields[i].type != ACPI_TYPE_INTEGER)
- return AE_ERROR;
- hpx->t2 = &hpx->type2_data;
- hpx->t2->revision = revision;
- hpx->t2->unc_err_mask_and = fields[2].integer.value;
- hpx->t2->unc_err_mask_or = fields[3].integer.value;
- hpx->t2->unc_err_sever_and = fields[4].integer.value;
- hpx->t2->unc_err_sever_or = fields[5].integer.value;
- hpx->t2->cor_err_mask_and = fields[6].integer.value;
- hpx->t2->cor_err_mask_or = fields[7].integer.value;
- hpx->t2->adv_err_cap_and = fields[8].integer.value;
- hpx->t2->adv_err_cap_or = fields[9].integer.value;
- hpx->t2->pci_exp_devctl_and = fields[10].integer.value;
- hpx->t2->pci_exp_devctl_or = fields[11].integer.value;
- hpx->t2->pci_exp_lnkctl_and = fields[12].integer.value;
- hpx->t2->pci_exp_lnkctl_or = fields[13].integer.value;
- hpx->t2->sec_unc_err_sever_and = fields[14].integer.value;
- hpx->t2->sec_unc_err_sever_or = fields[15].integer.value;
- hpx->t2->sec_unc_err_mask_and = fields[16].integer.value;
- hpx->t2->sec_unc_err_mask_or = fields[17].integer.value;
- break;
- default:
- printk(KERN_WARNING
- "%s: Type 2 Revision %d record not supported\n",
- __func__, revision);
- return AE_ERROR;
- }
- return AE_OK;
-}
-
-static acpi_status
-acpi_run_hpx(acpi_handle handle, struct hotplug_params *hpx)
-{
- acpi_status status;
- struct acpi_buffer buffer = {ACPI_ALLOCATE_BUFFER, NULL};
- union acpi_object *package, *record, *fields;
- u32 type;
- int i;
-
- /* Clear the return buffer with zeros */
- memset(hpx, 0, sizeof(struct hotplug_params));
-
- status = acpi_evaluate_object(handle, "_HPX", NULL, &buffer);
- if (ACPI_FAILURE(status))
- return status;
-
- package = (union acpi_object *)buffer.pointer;
- if (package->type != ACPI_TYPE_PACKAGE) {
- status = AE_ERROR;
- goto exit;
- }
-
- for (i = 0; i < package->package.count; i++) {
- record = &package->package.elements[i];
- if (record->type != ACPI_TYPE_PACKAGE) {
- status = AE_ERROR;
- goto exit;
- }
-
- fields = record->package.elements;
- if (fields[0].type != ACPI_TYPE_INTEGER ||
- fields[1].type != ACPI_TYPE_INTEGER) {
- status = AE_ERROR;
- goto exit;
- }
-
- type = fields[0].integer.value;
- switch (type) {
- case 0:
- status = decode_type0_hpx_record(record, hpx);
- if (ACPI_FAILURE(status))
- goto exit;
- break;
- case 1:
- status = decode_type1_hpx_record(record, hpx);
- if (ACPI_FAILURE(status))
- goto exit;
- break;
- case 2:
- status = decode_type2_hpx_record(record, hpx);
- if (ACPI_FAILURE(status))
- goto exit;
- break;
- default:
- printk(KERN_ERR "%s: Type %d record not supported\n",
- __func__, type);
- status = AE_ERROR;
- goto exit;
- }
- }
- exit:
- kfree(buffer.pointer);
- return status;
-}
-
-static acpi_status
-acpi_run_hpp(acpi_handle handle, struct hotplug_params *hpp)
-{
- acpi_status status;
- struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
- union acpi_object *package, *fields;
- int i;
-
- memset(hpp, 0, sizeof(struct hotplug_params));
-
- status = acpi_evaluate_object(handle, "_HPP", NULL, &buffer);
- if (ACPI_FAILURE(status))
- return status;
-
- package = (union acpi_object *) buffer.pointer;
- if (package->type != ACPI_TYPE_PACKAGE ||
- package->package.count != 4) {
- status = AE_ERROR;
- goto exit;
- }
-
- fields = package->package.elements;
- for (i = 0; i < 4; i++) {
- if (fields[i].type != ACPI_TYPE_INTEGER) {
- status = AE_ERROR;
- goto exit;
- }
- }
-
- hpp->t0 = &hpp->type0_data;
- hpp->t0->revision = 1;
- hpp->t0->cache_line_size = fields[0].integer.value;
- hpp->t0->latency_timer = fields[1].integer.value;
- hpp->t0->enable_serr = fields[2].integer.value;
- hpp->t0->enable_perr = fields[3].integer.value;
-
-exit:
- kfree(buffer.pointer);
- return status;
-}
-
-
-
/* acpi_run_oshp - get control of hotplug from the firmware
*
* @handle - the handle of the hotplug controller.
return status;
}
-/* pci_get_hp_params
- *
- * @dev - the pci_dev for which we want parameters
- * @hpp - allocated by the caller
- */
-int pci_get_hp_params(struct pci_dev *dev, struct hotplug_params *hpp)
-{
- acpi_status status;
- acpi_handle handle, phandle;
- struct pci_bus *pbus;
-
- handle = NULL;
- for (pbus = dev->bus; pbus; pbus = pbus->parent) {
- handle = acpi_pci_get_bridge_handle(pbus);
- if (handle)
- break;
- }
-
- /*
- * _HPP settings apply to all child buses, until another _HPP is
- * encountered. If we don't find an _HPP for the input pci dev,
- * look for it in the parent device scope since that would apply to
- * this pci dev.
- */
- while (handle) {
- status = acpi_run_hpx(handle, hpp);
- if (ACPI_SUCCESS(status))
- return 0;
- status = acpi_run_hpp(handle, hpp);
- if (ACPI_SUCCESS(status))
- return 0;
- if (acpi_is_root_bridge(handle))
- break;
- status = acpi_get_parent(handle, &phandle);
- if (ACPI_FAILURE(status))
- break;
- handle = phandle;
- }
- return -ENODEV;
-}
-EXPORT_SYMBOL_GPL(pci_get_hp_params);
-
/**
* acpi_get_hp_hw_control_from_firmware
* @dev: the pci_dev of the bridge that has a hotplug controller
static int acpiphp_hotplug_notify(struct acpi_device *adev, u32 type);
static void acpiphp_post_dock_fixup(struct acpi_device *adev);
static void acpiphp_sanitize_bus(struct pci_bus *bus);
-static void acpiphp_set_hpp_values(struct pci_bus *bus);
static void hotplug_event(u32 type, struct acpiphp_context *context);
static void free_bridge(struct kref *kref);
__pci_bus_assign_resources(bus, &add_list, NULL);
acpiphp_sanitize_bus(bus);
- acpiphp_set_hpp_values(bus);
+ pcie_bus_configure_settings(bus);
acpiphp_set_acpi_region(slot);
list_for_each_entry(dev, &bus->devices, bus_list) {
}
}
-static void acpiphp_set_hpp_values(struct pci_bus *bus)
-{
- struct pci_dev *dev;
-
- list_for_each_entry(dev, &bus->devices, bus_list)
- pci_configure_slot(dev);
-}
-
/*
* Remove devices for which we could not assign resources, call
* arch specific code to fix-up the bus
struct slot *slot;
wait_queue_head_t queue; /* sleep & wake process */
u32 slot_cap;
- u32 slot_ctrl;
+ u16 slot_ctrl;
struct timer_list poll_timer;
unsigned long cmd_started; /* jiffies */
unsigned int cmd_busy:1;
goto err_out_none;
}
+ if (!dev->port->subordinate) {
+ /* Can happen if we run out of bus numbers during probe */
+ dev_err(&dev->device,
+ "Hotplug bridge without secondary bus, ignoring\n");
+ goto err_out_none;
+ }
+
ctrl = pcie_init(dev);
if (!ctrl) {
dev_err(&dev->device, "Controller initialization failed\n");
* interrupts.
*/
if (!rc)
- ctrl_info(ctrl, "Timeout on hotplug command %#010x (issued %u msec ago)\n",
+ ctrl_info(ctrl, "Timeout on hotplug command %#06x (issued %u msec ago)\n",
ctrl->slot_ctrl,
- jiffies_to_msecs(now - ctrl->cmd_started));
+ jiffies_to_msecs(jiffies - ctrl->cmd_started));
}
/**
default:
return;
}
+ pcie_write_cmd(ctrl, slot_cmd, PCI_EXP_SLTCTL_AIC);
ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, slot_cmd);
- pcie_write_cmd(ctrl, slot_cmd, PCI_EXP_SLTCTL_AIC);
}
void pciehp_green_led_on(struct slot *slot)
PCI_EXP_SLTCTL_DLLSCE);
pcie_write_cmd(ctrl, cmd, mask);
+ ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
+ pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, cmd);
}
static void pcie_disable_notification(struct controller *ctrl)
PCI_EXP_SLTCTL_HPIE | PCI_EXP_SLTCTL_CCIE |
PCI_EXP_SLTCTL_DLLSCE);
pcie_write_cmd(ctrl, 0, mask);
+ ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
+ pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, 0);
}
/*
stat_mask |= PCI_EXP_SLTSTA_DLLSC;
pcie_write_cmd(ctrl, 0, ctrl_mask);
+ ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
+ pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, 0);
if (pciehp_poll_mode)
del_timer_sync(&ctrl->poll_timer);
pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, stat_mask);
pcie_write_cmd(ctrl, ctrl_mask, ctrl_mask);
+ ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
+ pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, ctrl_mask);
if (pciehp_poll_mode)
int_poll_timeout(ctrl->poll_timer.data);
PCI_EXP_SLTSTA_MRLSC | PCI_EXP_SLTSTA_PDC |
PCI_EXP_SLTSTA_CC | PCI_EXP_SLTSTA_DLLSC);
- /* Disable software notification */
- pcie_disable_notification(ctrl);
-
ctrl_info(ctrl, "Slot #%d AttnBtn%c AttnInd%c PwrInd%c PwrCtrl%c MRL%c Interlock%c NoCompl%c LLActRep%c\n",
(slot_cap & PCI_EXP_SLTCAP_PSN) >> 19,
FLAG(slot_cap, PCI_EXP_SLTCAP_ABP),
pci_hp_add_bridge(dev);
pci_assign_unassigned_bridge_resources(bridge);
-
- list_for_each_entry(dev, &parent->devices, bus_list) {
- if ((dev->class >> 16) == PCI_BASE_CLASS_DISPLAY)
- continue;
-
- pci_configure_slot(dev);
- }
-
+ pcie_bus_configure_settings(parent);
pci_bus_add_devices(parent);
out:
+++ /dev/null
-/*
- * Copyright (C) 1995,2001 Compaq Computer Corporation
- * Copyright (C) 2001 Greg Kroah-Hartman (greg@kroah.com)
- * Copyright (C) 2001 IBM Corp.
- * Copyright (C) 2003-2004 Intel Corporation
- * (c) Copyright 2009 Hewlett-Packard Development Company, L.P.
- *
- * All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or (at
- * your option) any later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
- * NON INFRINGEMENT. See the GNU General Public License for more
- * details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/pci.h>
-#include <linux/export.h>
-#include <linux/pci_hotplug.h>
-
-static struct hpp_type0 pci_default_type0 = {
- .revision = 1,
- .cache_line_size = 8,
- .latency_timer = 0x40,
- .enable_serr = 0,
- .enable_perr = 0,
-};
-
-static void program_hpp_type0(struct pci_dev *dev, struct hpp_type0 *hpp)
-{
- u16 pci_cmd, pci_bctl;
-
- if (!hpp) {
- /*
- * Perhaps we *should* use default settings for PCIe, but
- * pciehp didn't, so we won't either.
- */
- if (pci_is_pcie(dev))
- return;
- dev_info(&dev->dev, "using default PCI settings\n");
- hpp = &pci_default_type0;
- }
-
- if (hpp->revision > 1) {
- dev_warn(&dev->dev,
- "PCI settings rev %d not supported; using defaults\n",
- hpp->revision);
- hpp = &pci_default_type0;
- }
-
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, hpp->cache_line_size);
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, hpp->latency_timer);
- pci_read_config_word(dev, PCI_COMMAND, &pci_cmd);
- if (hpp->enable_serr)
- pci_cmd |= PCI_COMMAND_SERR;
- else
- pci_cmd &= ~PCI_COMMAND_SERR;
- if (hpp->enable_perr)
- pci_cmd |= PCI_COMMAND_PARITY;
- else
- pci_cmd &= ~PCI_COMMAND_PARITY;
- pci_write_config_word(dev, PCI_COMMAND, pci_cmd);
-
- /* Program bridge control value */
- if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
- pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER,
- hpp->latency_timer);
- pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &pci_bctl);
- if (hpp->enable_serr)
- pci_bctl |= PCI_BRIDGE_CTL_SERR;
- else
- pci_bctl &= ~PCI_BRIDGE_CTL_SERR;
- if (hpp->enable_perr)
- pci_bctl |= PCI_BRIDGE_CTL_PARITY;
- else
- pci_bctl &= ~PCI_BRIDGE_CTL_PARITY;
- pci_write_config_word(dev, PCI_BRIDGE_CONTROL, pci_bctl);
- }
-}
-
-static void program_hpp_type1(struct pci_dev *dev, struct hpp_type1 *hpp)
-{
- if (hpp)
- dev_warn(&dev->dev, "PCI-X settings not supported\n");
-}
-
-static void program_hpp_type2(struct pci_dev *dev, struct hpp_type2 *hpp)
-{
- int pos;
- u32 reg32;
-
- if (!hpp)
- return;
-
- if (hpp->revision > 1) {
- dev_warn(&dev->dev, "PCIe settings rev %d not supported\n",
- hpp->revision);
- return;
- }
-
- /* Initialize Device Control Register */
- pcie_capability_clear_and_set_word(dev, PCI_EXP_DEVCTL,
- ~hpp->pci_exp_devctl_and, hpp->pci_exp_devctl_or);
-
- /* Initialize Link Control Register */
- if (dev->subordinate)
- pcie_capability_clear_and_set_word(dev, PCI_EXP_LNKCTL,
- ~hpp->pci_exp_lnkctl_and, hpp->pci_exp_lnkctl_or);
-
- /* Find Advanced Error Reporting Enhanced Capability */
- pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR);
- if (!pos)
- return;
-
- /* Initialize Uncorrectable Error Mask Register */
- pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, ®32);
- reg32 = (reg32 & hpp->unc_err_mask_and) | hpp->unc_err_mask_or;
- pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, reg32);
-
- /* Initialize Uncorrectable Error Severity Register */
- pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_SEVER, ®32);
- reg32 = (reg32 & hpp->unc_err_sever_and) | hpp->unc_err_sever_or;
- pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_SEVER, reg32);
-
- /* Initialize Correctable Error Mask Register */
- pci_read_config_dword(dev, pos + PCI_ERR_COR_MASK, ®32);
- reg32 = (reg32 & hpp->cor_err_mask_and) | hpp->cor_err_mask_or;
- pci_write_config_dword(dev, pos + PCI_ERR_COR_MASK, reg32);
-
- /* Initialize Advanced Error Capabilities and Control Register */
- pci_read_config_dword(dev, pos + PCI_ERR_CAP, ®32);
- reg32 = (reg32 & hpp->adv_err_cap_and) | hpp->adv_err_cap_or;
- pci_write_config_dword(dev, pos + PCI_ERR_CAP, reg32);
-
- /*
- * FIXME: The following two registers are not supported yet.
- *
- * o Secondary Uncorrectable Error Severity Register
- * o Secondary Uncorrectable Error Mask Register
- */
-}
-
-void pci_configure_slot(struct pci_dev *dev)
-{
- struct pci_dev *cdev;
- struct hotplug_params hpp;
- int ret;
-
- if (!(dev->hdr_type == PCI_HEADER_TYPE_NORMAL ||
- (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE &&
- (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI)))
- return;
-
- pcie_bus_configure_settings(dev->bus);
-
- memset(&hpp, 0, sizeof(hpp));
- ret = pci_get_hp_params(dev, &hpp);
- if (ret)
- dev_warn(&dev->dev, "no hotplug settings from platform\n");
-
- program_hpp_type2(dev, hpp.t2);
- program_hpp_type1(dev, hpp.t1);
- program_hpp_type0(dev, hpp.t0);
-
- if (dev->subordinate) {
- list_for_each_entry(cdev, &dev->subordinate->devices,
- bus_list)
- pci_configure_slot(cdev);
- }
-}
-EXPORT_SYMBOL_GPL(pci_configure_slot);
}
pci_assign_unassigned_bridge_resources(bridge);
-
- list_for_each_entry(dev, &parent->devices, bus_list) {
- if (PCI_SLOT(dev->devfn) != p_slot->device)
- continue;
- pci_configure_slot(dev);
- }
-
+ pcie_bus_configure_settings(parent);
pci_bus_add_devices(parent);
out:
* our dev as the physical function and the assigned bit is set
*/
if (vfdev->is_virtfn && (vfdev->physfn == dev) &&
- (vfdev->dev_flags & PCI_DEV_FLAGS_ASSIGNED))
+ pci_is_dev_assigned(vfdev))
vfs_assigned++;
vfdev = pci_get_device(dev->vendor, dev_id, vfdev);
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/pci.h>
+#include <linux/pci_hotplug.h>
#include <linux/module.h>
#include <linux/pci-aspm.h>
#include <linux/pci-acpi.h>
#include <linux/pm_qos.h>
#include "pci.h"
+phys_addr_t acpi_pci_root_get_mcfg_addr(acpi_handle handle)
+{
+ acpi_status status = AE_NOT_EXIST;
+ unsigned long long mcfg_addr;
+
+ if (handle)
+ status = acpi_evaluate_integer(handle, METHOD_NAME__CBA,
+ NULL, &mcfg_addr);
+ if (ACPI_FAILURE(status))
+ return 0;
+
+ return (phys_addr_t)mcfg_addr;
+}
+
+static acpi_status decode_type0_hpx_record(union acpi_object *record,
+ struct hotplug_params *hpx)
+{
+ int i;
+ union acpi_object *fields = record->package.elements;
+ u32 revision = fields[1].integer.value;
+
+ switch (revision) {
+ case 1:
+ if (record->package.count != 6)
+ return AE_ERROR;
+ for (i = 2; i < 6; i++)
+ if (fields[i].type != ACPI_TYPE_INTEGER)
+ return AE_ERROR;
+ hpx->t0 = &hpx->type0_data;
+ hpx->t0->revision = revision;
+ hpx->t0->cache_line_size = fields[2].integer.value;
+ hpx->t0->latency_timer = fields[3].integer.value;
+ hpx->t0->enable_serr = fields[4].integer.value;
+ hpx->t0->enable_perr = fields[5].integer.value;
+ break;
+ default:
+ printk(KERN_WARNING
+ "%s: Type 0 Revision %d record not supported\n",
+ __func__, revision);
+ return AE_ERROR;
+ }
+ return AE_OK;
+}
+
+static acpi_status decode_type1_hpx_record(union acpi_object *record,
+ struct hotplug_params *hpx)
+{
+ int i;
+ union acpi_object *fields = record->package.elements;
+ u32 revision = fields[1].integer.value;
+
+ switch (revision) {
+ case 1:
+ if (record->package.count != 5)
+ return AE_ERROR;
+ for (i = 2; i < 5; i++)
+ if (fields[i].type != ACPI_TYPE_INTEGER)
+ return AE_ERROR;
+ hpx->t1 = &hpx->type1_data;
+ hpx->t1->revision = revision;
+ hpx->t1->max_mem_read = fields[2].integer.value;
+ hpx->t1->avg_max_split = fields[3].integer.value;
+ hpx->t1->tot_max_split = fields[4].integer.value;
+ break;
+ default:
+ printk(KERN_WARNING
+ "%s: Type 1 Revision %d record not supported\n",
+ __func__, revision);
+ return AE_ERROR;
+ }
+ return AE_OK;
+}
+
+static acpi_status decode_type2_hpx_record(union acpi_object *record,
+ struct hotplug_params *hpx)
+{
+ int i;
+ union acpi_object *fields = record->package.elements;
+ u32 revision = fields[1].integer.value;
+
+ switch (revision) {
+ case 1:
+ if (record->package.count != 18)
+ return AE_ERROR;
+ for (i = 2; i < 18; i++)
+ if (fields[i].type != ACPI_TYPE_INTEGER)
+ return AE_ERROR;
+ hpx->t2 = &hpx->type2_data;
+ hpx->t2->revision = revision;
+ hpx->t2->unc_err_mask_and = fields[2].integer.value;
+ hpx->t2->unc_err_mask_or = fields[3].integer.value;
+ hpx->t2->unc_err_sever_and = fields[4].integer.value;
+ hpx->t2->unc_err_sever_or = fields[5].integer.value;
+ hpx->t2->cor_err_mask_and = fields[6].integer.value;
+ hpx->t2->cor_err_mask_or = fields[7].integer.value;
+ hpx->t2->adv_err_cap_and = fields[8].integer.value;
+ hpx->t2->adv_err_cap_or = fields[9].integer.value;
+ hpx->t2->pci_exp_devctl_and = fields[10].integer.value;
+ hpx->t2->pci_exp_devctl_or = fields[11].integer.value;
+ hpx->t2->pci_exp_lnkctl_and = fields[12].integer.value;
+ hpx->t2->pci_exp_lnkctl_or = fields[13].integer.value;
+ hpx->t2->sec_unc_err_sever_and = fields[14].integer.value;
+ hpx->t2->sec_unc_err_sever_or = fields[15].integer.value;
+ hpx->t2->sec_unc_err_mask_and = fields[16].integer.value;
+ hpx->t2->sec_unc_err_mask_or = fields[17].integer.value;
+ break;
+ default:
+ printk(KERN_WARNING
+ "%s: Type 2 Revision %d record not supported\n",
+ __func__, revision);
+ return AE_ERROR;
+ }
+ return AE_OK;
+}
+
+static acpi_status acpi_run_hpx(acpi_handle handle, struct hotplug_params *hpx)
+{
+ acpi_status status;
+ struct acpi_buffer buffer = {ACPI_ALLOCATE_BUFFER, NULL};
+ union acpi_object *package, *record, *fields;
+ u32 type;
+ int i;
+
+ /* Clear the return buffer with zeros */
+ memset(hpx, 0, sizeof(struct hotplug_params));
+
+ status = acpi_evaluate_object(handle, "_HPX", NULL, &buffer);
+ if (ACPI_FAILURE(status))
+ return status;
+
+ package = (union acpi_object *)buffer.pointer;
+ if (package->type != ACPI_TYPE_PACKAGE) {
+ status = AE_ERROR;
+ goto exit;
+ }
+
+ for (i = 0; i < package->package.count; i++) {
+ record = &package->package.elements[i];
+ if (record->type != ACPI_TYPE_PACKAGE) {
+ status = AE_ERROR;
+ goto exit;
+ }
+
+ fields = record->package.elements;
+ if (fields[0].type != ACPI_TYPE_INTEGER ||
+ fields[1].type != ACPI_TYPE_INTEGER) {
+ status = AE_ERROR;
+ goto exit;
+ }
+
+ type = fields[0].integer.value;
+ switch (type) {
+ case 0:
+ status = decode_type0_hpx_record(record, hpx);
+ if (ACPI_FAILURE(status))
+ goto exit;
+ break;
+ case 1:
+ status = decode_type1_hpx_record(record, hpx);
+ if (ACPI_FAILURE(status))
+ goto exit;
+ break;
+ case 2:
+ status = decode_type2_hpx_record(record, hpx);
+ if (ACPI_FAILURE(status))
+ goto exit;
+ break;
+ default:
+ printk(KERN_ERR "%s: Type %d record not supported\n",
+ __func__, type);
+ status = AE_ERROR;
+ goto exit;
+ }
+ }
+ exit:
+ kfree(buffer.pointer);
+ return status;
+}
+
+static acpi_status acpi_run_hpp(acpi_handle handle, struct hotplug_params *hpp)
+{
+ acpi_status status;
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+ union acpi_object *package, *fields;
+ int i;
+
+ memset(hpp, 0, sizeof(struct hotplug_params));
+
+ status = acpi_evaluate_object(handle, "_HPP", NULL, &buffer);
+ if (ACPI_FAILURE(status))
+ return status;
+
+ package = (union acpi_object *) buffer.pointer;
+ if (package->type != ACPI_TYPE_PACKAGE ||
+ package->package.count != 4) {
+ status = AE_ERROR;
+ goto exit;
+ }
+
+ fields = package->package.elements;
+ for (i = 0; i < 4; i++) {
+ if (fields[i].type != ACPI_TYPE_INTEGER) {
+ status = AE_ERROR;
+ goto exit;
+ }
+ }
+
+ hpp->t0 = &hpp->type0_data;
+ hpp->t0->revision = 1;
+ hpp->t0->cache_line_size = fields[0].integer.value;
+ hpp->t0->latency_timer = fields[1].integer.value;
+ hpp->t0->enable_serr = fields[2].integer.value;
+ hpp->t0->enable_perr = fields[3].integer.value;
+
+exit:
+ kfree(buffer.pointer);
+ return status;
+}
+
+/* pci_get_hp_params
+ *
+ * @dev - the pci_dev for which we want parameters
+ * @hpp - allocated by the caller
+ */
+int pci_get_hp_params(struct pci_dev *dev, struct hotplug_params *hpp)
+{
+ acpi_status status;
+ acpi_handle handle, phandle;
+ struct pci_bus *pbus;
+
+ handle = NULL;
+ for (pbus = dev->bus; pbus; pbus = pbus->parent) {
+ handle = acpi_pci_get_bridge_handle(pbus);
+ if (handle)
+ break;
+ }
+
+ /*
+ * _HPP settings apply to all child buses, until another _HPP is
+ * encountered. If we don't find an _HPP for the input pci dev,
+ * look for it in the parent device scope since that would apply to
+ * this pci dev.
+ */
+ while (handle) {
+ status = acpi_run_hpx(handle, hpp);
+ if (ACPI_SUCCESS(status))
+ return 0;
+ status = acpi_run_hpp(handle, hpp);
+ if (ACPI_SUCCESS(status))
+ return 0;
+ if (acpi_is_root_bridge(handle))
+ break;
+ status = acpi_get_parent(handle, &phandle);
+ if (ACPI_FAILURE(status))
+ break;
+ handle = phandle;
+ }
+ return -ENODEV;
+}
+EXPORT_SYMBOL_GPL(pci_get_hp_params);
+
/**
* pci_acpi_wake_bus - Root bus wakeup notification fork function.
* @work: Work item to handle.
return acpi_add_pm_notifier(dev, &pci_dev->dev, pci_acpi_wake_dev);
}
-phys_addr_t acpi_pci_root_get_mcfg_addr(acpi_handle handle)
-{
- acpi_status status = AE_NOT_EXIST;
- unsigned long long mcfg_addr;
-
- if (handle)
- status = acpi_evaluate_integer(handle, METHOD_NAME__CBA,
- NULL, &mcfg_addr);
- if (ACPI_FAILURE(status))
- return 0;
-
- return (phys_addr_t)mcfg_addr;
-}
-
/*
* _SxD returns the D-state with the highest power
* (lowest D-state number) supported in the S-state "x".
unsigned long driver_data)
{
struct pci_dynid *dynid;
- int retval;
dynid = kzalloc(sizeof(*dynid), GFP_KERNEL);
if (!dynid)
list_add_tail(&dynid->node, &drv->dynids.list);
spin_unlock(&drv->dynids.lock);
- retval = driver_attach(&drv->driver);
-
- return retval;
+ return driver_attach(&drv->driver);
}
EXPORT_SYMBOL_GPL(pci_add_dynid);
{
struct pci_dev *pci_dev = to_pci_dev(dev);
- return sprintf(buf, "pci:v%08Xd%08Xsv%08Xsd%08Xbc%02Xsc%02Xi%02x\n",
+ return sprintf(buf, "pci:v%08Xd%08Xsv%08Xsd%08Xbc%02Xsc%02Xi%02X\n",
pci_dev->vendor, pci_dev->device,
pci_dev->subsystem_vendor, pci_dev->subsystem_device,
(u8)(pci_dev->class >> 16), (u8)(pci_dev->class >> 8),
if (target_state == PCI_POWER_ERROR)
return -EIO;
- /* D3cold during system suspend/hibernate is not supported */
- if (target_state > PCI_D3hot)
- target_state = PCI_D3hot;
-
pci_enable_wake(dev, target_state, device_may_wakeup(&dev->dev));
error = pci_set_power_state(dev, target_state);
return 0;
}
-#ifdef CONFIG_PM_RUNTIME
-struct d3cold_info {
- bool no_d3cold;
- unsigned int d3cold_delay;
-};
-
-static int pci_dev_d3cold_info(struct pci_dev *pdev, void *data)
-{
- struct d3cold_info *info = data;
-
- info->d3cold_delay = max_t(unsigned int, pdev->d3cold_delay,
- info->d3cold_delay);
- if (pdev->no_d3cold)
- info->no_d3cold = true;
- return 0;
-}
-
-static int pcie_port_runtime_suspend(struct device *dev)
-{
- struct pci_dev *pdev = to_pci_dev(dev);
- struct d3cold_info d3cold_info = {
- .no_d3cold = false,
- .d3cold_delay = PCI_PM_D3_WAIT,
- };
-
- /*
- * If any subordinate device disable D3cold, we should not put
- * the port into D3cold. The D3cold delay of port should be
- * the max of that of all subordinate devices.
- */
- pci_walk_bus(pdev->subordinate, pci_dev_d3cold_info, &d3cold_info);
- pdev->no_d3cold = d3cold_info.no_d3cold;
- pdev->d3cold_delay = d3cold_info.d3cold_delay;
- return 0;
-}
-
-static int pcie_port_runtime_resume(struct device *dev)
-{
- return 0;
-}
-
-static int pci_dev_pme_poll(struct pci_dev *pdev, void *data)
-{
- bool *pme_poll = data;
-
- if (pdev->pme_poll)
- *pme_poll = true;
- return 0;
-}
-
-static int pcie_port_runtime_idle(struct device *dev)
-{
- struct pci_dev *pdev = to_pci_dev(dev);
- bool pme_poll = false;
-
- /*
- * If any subordinate device needs pme poll, we should keep
- * the port in D0, because we need port in D0 to poll it.
- */
- pci_walk_bus(pdev->subordinate, pci_dev_pme_poll, &pme_poll);
- /* Delay for a short while to prevent too frequent suspend/resume */
- if (!pme_poll)
- pm_schedule_suspend(dev, 10);
- return -EBUSY;
-}
-#else
-#define pcie_port_runtime_suspend NULL
-#define pcie_port_runtime_resume NULL
-#define pcie_port_runtime_idle NULL
-#endif
-
static const struct dev_pm_ops pcie_portdrv_pm_ops = {
.suspend = pcie_port_device_suspend,
.resume = pcie_port_device_resume,
.poweroff = pcie_port_device_suspend,
.restore = pcie_port_device_resume,
.resume_noirq = pcie_port_resume_noirq,
- .runtime_suspend = pcie_port_runtime_suspend,
- .runtime_resume = pcie_port_runtime_resume,
- .runtime_idle = pcie_port_runtime_idle,
};
#define PCIE_PORTDRV_PM_OPS (&pcie_portdrv_pm_ops)
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/pci.h>
+#include <linux/pci_hotplug.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/cpumask.h>
}
EXPORT_SYMBOL(pci_add_new_bus);
+static void pci_enable_crs(struct pci_dev *pdev)
+{
+ u16 root_cap = 0;
+
+ /* Enable CRS Software Visibility if supported */
+ pcie_capability_read_word(pdev, PCI_EXP_RTCAP, &root_cap);
+ if (root_cap & PCI_EXP_RTCAP_CRSVIS)
+ pcie_capability_set_word(pdev, PCI_EXP_RTCTL,
+ PCI_EXP_RTCTL_CRSSVE);
+}
+
/*
* If it's a bridge, configure it and scan the bus behind it.
* For CardBus bridges, we don't scan behind as the devices will
pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
+ pci_enable_crs(dev);
+
if ((secondary || subordinate) && !pcibios_assign_all_busses() &&
!is_cardbus && !broken) {
unsigned int cmax;
return 0;
}
+static struct hpp_type0 pci_default_type0 = {
+ .revision = 1,
+ .cache_line_size = 8,
+ .latency_timer = 0x40,
+ .enable_serr = 0,
+ .enable_perr = 0,
+};
+
+static void program_hpp_type0(struct pci_dev *dev, struct hpp_type0 *hpp)
+{
+ u16 pci_cmd, pci_bctl;
+
+ if (!hpp)
+ hpp = &pci_default_type0;
+
+ if (hpp->revision > 1) {
+ dev_warn(&dev->dev,
+ "PCI settings rev %d not supported; using defaults\n",
+ hpp->revision);
+ hpp = &pci_default_type0;
+ }
+
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, hpp->cache_line_size);
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, hpp->latency_timer);
+ pci_read_config_word(dev, PCI_COMMAND, &pci_cmd);
+ if (hpp->enable_serr)
+ pci_cmd |= PCI_COMMAND_SERR;
+ if (hpp->enable_perr)
+ pci_cmd |= PCI_COMMAND_PARITY;
+ pci_write_config_word(dev, PCI_COMMAND, pci_cmd);
+
+ /* Program bridge control value */
+ if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+ pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER,
+ hpp->latency_timer);
+ pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &pci_bctl);
+ if (hpp->enable_serr)
+ pci_bctl |= PCI_BRIDGE_CTL_SERR;
+ if (hpp->enable_perr)
+ pci_bctl |= PCI_BRIDGE_CTL_PARITY;
+ pci_write_config_word(dev, PCI_BRIDGE_CONTROL, pci_bctl);
+ }
+}
+
+static void program_hpp_type1(struct pci_dev *dev, struct hpp_type1 *hpp)
+{
+ if (hpp)
+ dev_warn(&dev->dev, "PCI-X settings not supported\n");
+}
+
+static void program_hpp_type2(struct pci_dev *dev, struct hpp_type2 *hpp)
+{
+ int pos;
+ u32 reg32;
+
+ if (!hpp)
+ return;
+
+ if (hpp->revision > 1) {
+ dev_warn(&dev->dev, "PCIe settings rev %d not supported\n",
+ hpp->revision);
+ return;
+ }
+
+ /*
+ * Don't allow _HPX to change MPS or MRRS settings. We manage
+ * those to make sure they're consistent with the rest of the
+ * platform.
+ */
+ hpp->pci_exp_devctl_and |= PCI_EXP_DEVCTL_PAYLOAD |
+ PCI_EXP_DEVCTL_READRQ;
+ hpp->pci_exp_devctl_or &= ~(PCI_EXP_DEVCTL_PAYLOAD |
+ PCI_EXP_DEVCTL_READRQ);
+
+ /* Initialize Device Control Register */
+ pcie_capability_clear_and_set_word(dev, PCI_EXP_DEVCTL,
+ ~hpp->pci_exp_devctl_and, hpp->pci_exp_devctl_or);
+
+ /* Initialize Link Control Register */
+ if (dev->subordinate)
+ pcie_capability_clear_and_set_word(dev, PCI_EXP_LNKCTL,
+ ~hpp->pci_exp_lnkctl_and, hpp->pci_exp_lnkctl_or);
+
+ /* Find Advanced Error Reporting Enhanced Capability */
+ pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR);
+ if (!pos)
+ return;
+
+ /* Initialize Uncorrectable Error Mask Register */
+ pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, ®32);
+ reg32 = (reg32 & hpp->unc_err_mask_and) | hpp->unc_err_mask_or;
+ pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, reg32);
+
+ /* Initialize Uncorrectable Error Severity Register */
+ pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_SEVER, ®32);
+ reg32 = (reg32 & hpp->unc_err_sever_and) | hpp->unc_err_sever_or;
+ pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_SEVER, reg32);
+
+ /* Initialize Correctable Error Mask Register */
+ pci_read_config_dword(dev, pos + PCI_ERR_COR_MASK, ®32);
+ reg32 = (reg32 & hpp->cor_err_mask_and) | hpp->cor_err_mask_or;
+ pci_write_config_dword(dev, pos + PCI_ERR_COR_MASK, reg32);
+
+ /* Initialize Advanced Error Capabilities and Control Register */
+ pci_read_config_dword(dev, pos + PCI_ERR_CAP, ®32);
+ reg32 = (reg32 & hpp->adv_err_cap_and) | hpp->adv_err_cap_or;
+ pci_write_config_dword(dev, pos + PCI_ERR_CAP, reg32);
+
+ /*
+ * FIXME: The following two registers are not supported yet.
+ *
+ * o Secondary Uncorrectable Error Severity Register
+ * o Secondary Uncorrectable Error Mask Register
+ */
+}
+
+static void pci_configure_device(struct pci_dev *dev)
+{
+ struct hotplug_params hpp;
+ int ret;
+
+ memset(&hpp, 0, sizeof(hpp));
+ ret = pci_get_hp_params(dev, &hpp);
+ if (ret)
+ return;
+
+ program_hpp_type2(dev, hpp.t2);
+ program_hpp_type1(dev, hpp.t1);
+ program_hpp_type0(dev, hpp.t0);
+}
+
static void pci_release_capabilities(struct pci_dev *dev)
{
pci_vpd_release(dev);
*l == 0x0000ffff || *l == 0xffff0000)
return false;
- /* Configuration request Retry Status */
- while (*l == 0xffff0001) {
+ /*
+ * Configuration Request Retry Status. Some root ports return the
+ * actual device ID instead of the synthetic ID (0xFFFF) required
+ * by the PCIe spec. Ignore the device ID and only check for
+ * (vendor id == 1).
+ */
+ while ((*l & 0xffff) == 0x0001) {
if (!crs_timeout)
return false;
{
int ret;
+ pci_configure_device(dev);
+
device_initialize(&dev->dev);
dev->dev.release = pci_release_dev;
#include <linux/ioport.h>
#include <linux/sched.h>
#include <linux/ktime.h>
+#include <linux/mm.h>
#include <asm/dma.h> /* isa_dma_bridge_buggy */
#include "pci.h"
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine);
+/* On IBM Crocodile ipr SAS adapters, expand BAR to system page size */
+static void quirk_extend_bar_to_page(struct pci_dev *dev)
+{
+ int i;
+
+ for (i = 0; i < PCI_STD_RESOURCE_END; i++) {
+ struct resource *r = &dev->resource[i];
+
+ if (r->flags & IORESOURCE_MEM && resource_size(r) < PAGE_SIZE) {
+ r->end = PAGE_SIZE - 1;
+ r->start = 0;
+ r->flags |= IORESOURCE_UNSET;
+ dev_info(&dev->dev, "expanded BAR %d to page size: %pR\n",
+ i, r);
+ }
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, 0x034a, quirk_extend_bar_to_page);
+
/*
* S3 868 and 968 chips report region size equal to 32M, but they decode 64M.
* If it's needed, re-allocate the region.
*/
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_REALTEK, 0x8169,
quirk_broken_intx_masking);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, PCI_ANY_ID,
+ quirk_broken_intx_masking);
#ifdef CONFIG_ACPI
/*
/* Intel 82801, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c49 */
DECLARE_PCI_FIXUP_HEADER(0x8086, 0x244e, quirk_use_pcie_bridge_dma_alias);
-static struct pci_dev *pci_func_0_dma_source(struct pci_dev *dev)
-{
- if (!PCI_FUNC(dev->devfn))
- return pci_dev_get(dev);
-
- return pci_get_slot(dev->bus, PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
-}
-
-static const struct pci_dev_dma_source {
- u16 vendor;
- u16 device;
- struct pci_dev *(*dma_source)(struct pci_dev *dev);
-} pci_dev_dma_source[] = {
- /*
- * https://bugzilla.redhat.com/show_bug.cgi?id=605888
- *
- * Some Ricoh devices use the function 0 source ID for DMA on
- * other functions of a multifunction device. The DMA devices
- * is therefore function 0, which will have implications of the
- * iommu grouping of these devices.
- */
- { PCI_VENDOR_ID_RICOH, 0xe822, pci_func_0_dma_source },
- { PCI_VENDOR_ID_RICOH, 0xe230, pci_func_0_dma_source },
- { PCI_VENDOR_ID_RICOH, 0xe832, pci_func_0_dma_source },
- { PCI_VENDOR_ID_RICOH, 0xe476, pci_func_0_dma_source },
- { 0 }
-};
-
-/*
- * IOMMUs with isolation capabilities need to be programmed with the
- * correct source ID of a device. In most cases, the source ID matches
- * the device doing the DMA, but sometimes hardware is broken and will
- * tag the DMA as being sourced from a different device. This function
- * allows that translation. Note that the reference count of the
- * returned device is incremented on all paths.
- */
-struct pci_dev *pci_get_dma_source(struct pci_dev *dev)
-{
- const struct pci_dev_dma_source *i;
-
- for (i = pci_dev_dma_source; i->dma_source; i++) {
- if ((i->vendor == dev->vendor ||
- i->vendor == (u16)PCI_ANY_ID) &&
- (i->device == dev->device ||
- i->device == (u16)PCI_ANY_ID))
- return i->dma_source(dev);
- }
-
- return pci_dev_get(dev);
-}
-
/*
* AMD has indicated that the devices below do not support peer-to-peer
* in any system where they are found in the southbridge with an AMD
return acs_flags & ~flags ? 0 : 1;
}
+static int pci_quirk_solarflare_acs(struct pci_dev *dev, u16 acs_flags)
+{
+ /*
+ * SV, TB, and UF are not relevant to multifunction endpoints.
+ *
+ * Solarflare indicates that peer-to-peer between functions is not
+ * possible, therefore RR, CR, and DT are not implemented. Mask
+ * these out as if they were clear in the ACS capabilities register.
+ */
+ acs_flags &= ~(PCI_ACS_SV | PCI_ACS_TB | PCI_ACS_RR |
+ PCI_ACS_CR | PCI_ACS_UF | PCI_ACS_DT);
+
+ return acs_flags ? 0 : 1;
+}
+
static const struct pci_dev_acs_enabled {
u16 vendor;
u16 device;
{ PCI_VENDOR_ID_ATI, 0x439d, pci_quirk_amd_sb_acs },
{ PCI_VENDOR_ID_ATI, 0x4384, pci_quirk_amd_sb_acs },
{ PCI_VENDOR_ID_ATI, 0x4399, pci_quirk_amd_sb_acs },
+ { PCI_VENDOR_ID_SOLARFLARE, 0x0903, pci_quirk_solarflare_acs },
+ { PCI_VENDOR_ID_SOLARFLARE, 0x0923, pci_quirk_solarflare_acs },
{ PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_intel_pch_acs },
{ 0 }
};
return ret;
}
-/*
- * find the upstream PCIe-to-PCI bridge of a PCI device
- * if the device is PCIE, return NULL
- * if the device isn't connected to a PCIe bridge (that is its parent is a
- * legacy PCI bridge and the bridge is directly connected to bus 0), return its
- * parent
- */
-struct pci_dev *pci_find_upstream_pcie_bridge(struct pci_dev *pdev)
-{
- struct pci_dev *tmp = NULL;
-
- if (pci_is_pcie(pdev))
- return NULL;
- while (1) {
- if (pci_is_root_bus(pdev->bus))
- break;
- pdev = pdev->bus->self;
- /* a p2p bridge */
- if (!pci_is_pcie(pdev)) {
- tmp = pdev;
- continue;
- }
- /* PCI device should connect to a PCIe bridge */
- if (pci_pcie_type(pdev) != PCI_EXP_TYPE_PCI_BRIDGE) {
- /* Busted hardware? */
- WARN_ON_ONCE(1);
- return NULL;
- }
- return pdev;
- }
-
- return tmp;
-}
-
static struct pci_bus *pci_do_find_bus(struct pci_bus *bus, unsigned char busnr)
{
struct pci_bus *child;
#define MASK(n) ((1 << (n)) - 1) /* make an n-bit mask */
-#define PCI_VENDOR_ID_VMWARE 0x15AD
#define PCI_DEVICE_ID_VMWARE_PVSCSI 0x07C0
/*
xen_pcibk_config_free_dyn_fields(dev);
xen_pcibk_config_free_dev(dev);
- dev->dev_flags &= ~PCI_DEV_FLAGS_ASSIGNED;
+ pci_clear_dev_assigned(dev);
pci_dev_put(dev);
kfree(psdev);
dev_dbg(&dev->dev, "reset device\n");
xen_pcibk_reset_device(dev);
- dev->dev_flags |= PCI_DEV_FLAGS_ASSIGNED;
+ pci_set_dev_assigned(dev);
return 0;
config_release:
#ifndef _AER_H_
#define _AER_H_
+#include <linux/types.h>
+
#define AER_NONFATAL 0
#define AER_FATAL 1
#define AER_CORRECTABLE 2
/* Wrappers for managed devices */
struct device;
+
+extern int devm_request_resource(struct device *dev, struct resource *root,
+ struct resource *new);
+extern void devm_release_resource(struct device *dev, struct resource *new);
+
#define devm_request_region(dev,start,n,name) \
__devm_request_region(dev, &ioport_resource, (start), (n), (name))
#define devm_request_mem_region(dev,start,n,name) \
* In the interest of not exposing interfaces to user-space unnecessarily,
* the following kernel-only defines are being added here.
*/
-#define PCI_DEVID(bus, devfn) ((((u16)bus) << 8) | devfn)
+#define PCI_DEVID(bus, devfn) ((((u16)(bus)) << 8) | (devfn))
/* return bus from PCI devid = ((u16)bus_number) << 8) | devfn */
#define PCI_BUS_NUM(x) (((x) >> 8) & 0xff)
#ifdef CONFIG_PCI_QUIRKS
void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev);
-struct pci_dev *pci_get_dma_source(struct pci_dev *dev);
int pci_dev_specific_acs_enabled(struct pci_dev *dev, u16 acs_flags);
void pci_dev_specific_enable_acs(struct pci_dev *dev);
#else
static inline void pci_fixup_device(enum pci_fixup_pass pass,
struct pci_dev *dev) { }
-static inline struct pci_dev *pci_get_dma_source(struct pci_dev *dev)
-{
- return pci_dev_get(dev);
-}
static inline int pci_dev_specific_acs_enabled(struct pci_dev *dev,
u16 acs_flags)
{
struct pci_dev *end, u16 acs_flags);
#define PCI_VPD_LRDT 0x80 /* Large Resource Data Type */
-#define PCI_VPD_LRDT_ID(x) (x | PCI_VPD_LRDT)
+#define PCI_VPD_LRDT_ID(x) ((x) | PCI_VPD_LRDT)
/* Large Resource Data Type Tag Item Names */
#define PCI_VPD_LTIN_ID_STRING 0x02 /* Identifier String */
int (*fn)(struct pci_dev *pdev,
u16 alias, void *data), void *data);
-/**
- * pci_find_upstream_pcie_bridge - find upstream PCIe-to-PCI bridge of a device
- * @pdev: the PCI device
- *
- * if the device is PCIE, return NULL
- * if the device isn't connected to a PCIe bridge (that is its parent is a
- * legacy PCI bridge and the bridge is directly connected to bus 0), return its
- * parent
- */
-struct pci_dev *pci_find_upstream_pcie_bridge(struct pci_dev *pdev);
-
+/* helper functions for operation of device flag */
+static inline void pci_set_dev_assigned(struct pci_dev *pdev)
+{
+ pdev->dev_flags |= PCI_DEV_FLAGS_ASSIGNED;
+}
+static inline void pci_clear_dev_assigned(struct pci_dev *pdev)
+{
+ pdev->dev_flags &= ~PCI_DEV_FLAGS_ASSIGNED;
+}
+static inline bool pci_is_dev_assigned(struct pci_dev *pdev)
+{
+ return (pdev->dev_flags & PCI_DEV_FLAGS_ASSIGNED) == PCI_DEV_FLAGS_ASSIGNED;
+}
#endif /* LINUX_PCI_H */
return -ENODEV;
}
#endif
-
-void pci_configure_slot(struct pci_dev *dev);
#endif
#define PCI_VENDOR_ID_MORETON 0x15aa
#define PCI_DEVICE_ID_RASTEL_2PORT 0x2000
+#define PCI_VENDOR_ID_VMWARE 0x15ad
+
#define PCI_VENDOR_ID_ZOLTRIX 0x15b0
#define PCI_DEVICE_ID_ZOLTRIX_2BD0 0x2bd0
#define PCI_EXP_RTCTL_PMEIE 0x0008 /* PME Interrupt Enable */
#define PCI_EXP_RTCTL_CRSSVE 0x0010 /* CRS Software Visibility Enable */
#define PCI_EXP_RTCAP 30 /* Root Capabilities */
+#define PCI_EXP_RTCAP_CRSVIS 0x0001 /* CRS Software Visibility capability */
#define PCI_EXP_RTSTA 32 /* Root Status */
#define PCI_EXP_RTSTA_PME 0x00010000 /* PME status */
#define PCI_EXP_RTSTA_PENDING 0x00020000 /* PME pending */
/*
* Managed region resource
*/
+static void devm_resource_release(struct device *dev, void *ptr)
+{
+ struct resource **r = ptr;
+
+ release_resource(*r);
+}
+
+/**
+ * devm_request_resource() - request and reserve an I/O or memory resource
+ * @dev: device for which to request the resource
+ * @root: root of the resource tree from which to request the resource
+ * @new: descriptor of the resource to request
+ *
+ * This is a device-managed version of request_resource(). There is usually
+ * no need to release resources requested by this function explicitly since
+ * that will be taken care of when the device is unbound from its driver.
+ * If for some reason the resource needs to be released explicitly, because
+ * of ordering issues for example, drivers must call devm_release_resource()
+ * rather than the regular release_resource().
+ *
+ * When a conflict is detected between any existing resources and the newly
+ * requested resource, an error message will be printed.
+ *
+ * Returns 0 on success or a negative error code on failure.
+ */
+int devm_request_resource(struct device *dev, struct resource *root,
+ struct resource *new)
+{
+ struct resource *conflict, **ptr;
+
+ ptr = devres_alloc(devm_resource_release, sizeof(*ptr), GFP_KERNEL);
+ if (!ptr)
+ return -ENOMEM;
+
+ *ptr = new;
+
+ conflict = request_resource_conflict(root, new);
+ if (conflict) {
+ dev_err(dev, "resource collision: %pR conflicts with %s %pR\n",
+ new, conflict->name, conflict);
+ devres_free(ptr);
+ return -EBUSY;
+ }
+
+ devres_add(dev, ptr);
+ return 0;
+}
+EXPORT_SYMBOL(devm_request_resource);
+
+static int devm_resource_match(struct device *dev, void *res, void *data)
+{
+ struct resource **ptr = res;
+
+ return *ptr == data;
+}
+
+/**
+ * devm_release_resource() - release a previously requested resource
+ * @dev: device for which to release the resource
+ * @new: descriptor of the resource to release
+ *
+ * Releases a resource previously requested using devm_request_resource().
+ */
+void devm_release_resource(struct device *dev, struct resource *new)
+{
+ WARN_ON(devres_release(dev, devm_resource_release, devm_resource_match,
+ new));
+}
+EXPORT_SYMBOL(devm_release_resource);
+
struct region_devres {
struct resource *parent;
resource_size_t start;
else
pci_restore_state(assigned_dev->dev);
- assigned_dev->dev->dev_flags &= ~PCI_DEV_FLAGS_ASSIGNED;
+ pci_clear_dev_assigned(assigned_dev->dev);
pci_release_regions(assigned_dev->dev);
pci_disable_device(assigned_dev->dev);
goto out_unmap;
}
- pdev->dev_flags |= PCI_DEV_FLAGS_ASSIGNED;
+ pci_set_dev_assigned(pdev);
dev_info(&pdev->dev, "kvm assign device\n");
iommu_detach_device(domain, &pdev->dev);
- pdev->dev_flags &= ~PCI_DEV_FLAGS_ASSIGNED;
+ pci_clear_dev_assigned(pdev);
dev_info(&pdev->dev, "kvm deassign device\n");
projects / firefly-linux-kernel-4.4.55.git / commitdiff