[PATCH] s2io: fixes
authorAnanda Raju <Ananda.Raju@neterion.com>
Fri, 21 Apr 2006 23:18:03 +0000 (19:18 -0400)
committerJeff Garzik <jeff@garzik.org>
Tue, 2 May 2006 19:16:36 +0000 (15:16 -0400)
Hi,
This patch contains some of the bug fixes done for S2io driver.
Following are the brief description of changes

1. Continuing with initialization if we get minimum required MSI-X vectors
2. fix for ethtool online link test fails
3. make wait_for_cmd_complete generic for all command status registers
4. Print "Device is on PCI-E bus" for Xframe-E card
5. CX4 requires additional delay after sw_reset, and requires higher value for igp
6. Fixed panic due to non-TCP and/or LLC/SNAP traffic in case of lro
7. remove legacy code for old transponder
8. SPECIAL_REG_WRITE made to use 32-bit writes irrespective of system type
9. handle link interrupt as per user guide for Xframe II
10. Wait till all interrupts hndled

Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/s2io.c
drivers/net/s2io.h

index 1dcda887cef733b80e7ceffe726c3023cfc23ccd..078a49e859361104c2974f63934017dc3aaa08c5 100644 (file)
@@ -223,9 +223,7 @@ static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid)
  * the XAUI.
  */
 
-#define SWITCH_SIGN    0xA5A5A5A5A5A5A5A5ULL
 #define        END_SIGN        0x0
-
 static const u64 herc_act_dtx_cfg[] = {
        /* Set address */
        0x8000051536750000ULL, 0x80000515367500E0ULL,
@@ -247,37 +245,19 @@ static const u64 herc_act_dtx_cfg[] = {
        END_SIGN
 };
 
-static const u64 xena_mdio_cfg[] = {
-       /* Reset PMA PLL */
-       0xC001010000000000ULL, 0xC0010100000000E0ULL,
-       0xC0010100008000E4ULL,
-       /* Remove Reset from PMA PLL */
-       0xC001010000000000ULL, 0xC0010100000000E0ULL,
-       0xC0010100000000E4ULL,
-       END_SIGN
-};
-
 static const u64 xena_dtx_cfg[] = {
+       /* Set address */
        0x8000051500000000ULL, 0x80000515000000E0ULL,
-       0x80000515D93500E4ULL, 0x8001051500000000ULL,
-       0x80010515000000E0ULL, 0x80010515001E00E4ULL,
-       0x8002051500000000ULL, 0x80020515000000E0ULL,
-       0x80020515F21000E4ULL,
-       /* Set PADLOOPBACKN */
-       0x8002051500000000ULL, 0x80020515000000E0ULL,
-       0x80020515B20000E4ULL, 0x8003051500000000ULL,
-       0x80030515000000E0ULL, 0x80030515B20000E4ULL,
-       0x8004051500000000ULL, 0x80040515000000E0ULL,
-       0x80040515B20000E4ULL, 0x8005051500000000ULL,
-       0x80050515000000E0ULL, 0x80050515B20000E4ULL,
-       SWITCH_SIGN,
-       /* Remove PADLOOPBACKN */
+       /* Write data */
+       0x80000515D9350004ULL, 0x80000515D93500E4ULL,
+       /* Set address */
+       0x8001051500000000ULL, 0x80010515000000E0ULL,
+       /* Write data */
+       0x80010515001E0004ULL, 0x80010515001E00E4ULL,
+       /* Set address */
        0x8002051500000000ULL, 0x80020515000000E0ULL,
-       0x80020515F20000E4ULL, 0x8003051500000000ULL,
-       0x80030515000000E0ULL, 0x80030515F20000E4ULL,
-       0x8004051500000000ULL, 0x80040515000000E0ULL,
-       0x80040515F20000E4ULL, 0x8005051500000000ULL,
-       0x80050515000000E0ULL, 0x80050515F20000E4ULL,
+       /* Write data */
+       0x80020515F2100004ULL, 0x80020515F21000E4ULL,
        END_SIGN
 };
 
@@ -552,11 +532,6 @@ static int init_shared_mem(struct s2io_nic *nic)
                                        rx_blocks->block_dma_addr +
                                        (rxd_size[nic->rxd_mode] * l);
                        }
-
-                       mac_control->rings[i].rx_blocks[j].block_virt_addr =
-                               tmp_v_addr;
-                       mac_control->rings[i].rx_blocks[j].block_dma_addr =
-                               tmp_p_addr;
                }
                /* Interlinking all Rx Blocks */
                for (j = 0; j < blk_cnt; j++) {
@@ -775,7 +750,21 @@ static int s2io_verify_pci_mode(nic_t *nic)
        return mode;
 }
 
+#define NEC_VENID   0x1033
+#define NEC_DEVID   0x0125
+static int s2io_on_nec_bridge(struct pci_dev *s2io_pdev)
+{
+       struct pci_dev *tdev = NULL;
+       while ((tdev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, tdev)) != NULL) {
+               if ((tdev->vendor == NEC_VENID) && (tdev->device == NEC_DEVID)){
+                       if (tdev->bus == s2io_pdev->bus->parent)
+                               return 1;
+               }
+       }
+       return 0;
+}
 
+int bus_speed[8] = {33, 133, 133, 200, 266, 133, 200, 266};
 /**
  * s2io_print_pci_mode -
  */
@@ -792,6 +781,14 @@ static int s2io_print_pci_mode(nic_t *nic)
        if ( val64 & PCI_MODE_UNKNOWN_MODE)
                return -1;      /* Unknown PCI mode */
 
+       config->bus_speed = bus_speed[mode];
+
+       if (s2io_on_nec_bridge(nic->pdev)) {
+               DBG_PRINT(ERR_DBG, "%s: Device is on PCI-E bus\n",
+                                                       nic->dev->name);
+               return mode;
+       }
+
        if (val64 & PCI_MODE_32_BITS) {
                DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
        } else {
@@ -801,35 +798,27 @@ static int s2io_print_pci_mode(nic_t *nic)
        switch(mode) {
                case PCI_MODE_PCI_33:
                        DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
-                       config->bus_speed = 33;
                        break;
                case PCI_MODE_PCI_66:
                        DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
-                       config->bus_speed = 133;
                        break;
                case PCI_MODE_PCIX_M1_66:
                        DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
-                       config->bus_speed = 133; /* Herc doubles the clock rate */
                        break;
                case PCI_MODE_PCIX_M1_100:
                        DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
-                       config->bus_speed = 200;
                        break;
                case PCI_MODE_PCIX_M1_133:
                        DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
-                       config->bus_speed = 266;
                        break;
                case PCI_MODE_PCIX_M2_66:
                        DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
-                       config->bus_speed = 133;
                        break;
                case PCI_MODE_PCIX_M2_100:
                        DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
-                       config->bus_speed = 200;
                        break;
                case PCI_MODE_PCIX_M2_133:
                        DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
-                       config->bus_speed = 266;
                        break;
                default:
                        return -1;      /* Unsupported bus speed */
@@ -857,7 +846,7 @@ static int init_nic(struct s2io_nic *nic)
        int i, j;
        mac_info_t *mac_control;
        struct config_param *config;
-       int mdio_cnt = 0, dtx_cnt = 0;
+       int dtx_cnt = 0;
        unsigned long long mem_share;
        int mem_size;
 
@@ -904,20 +893,6 @@ static int init_nic(struct s2io_nic *nic)
        val64 = dev->mtu;
        writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
 
-       /*
-        * Configuring the XAUI Interface of Xena.
-        * ***************************************
-        * To Configure the Xena's XAUI, one has to write a series
-        * of 64 bit values into two registers in a particular
-        * sequence. Hence a macro 'SWITCH_SIGN' has been defined
-        * which will be defined in the array of configuration values
-        * (xena_dtx_cfg & xena_mdio_cfg) at appropriate places
-        * to switch writing from one regsiter to another. We continue
-        * writing these values until we encounter the 'END_SIGN' macro.
-        * For example, After making a series of 21 writes into
-        * dtx_control register the 'SWITCH_SIGN' appears and hence we
-        * start writing into mdio_control until we encounter END_SIGN.
-        */
        if (nic->device_type & XFRAME_II_DEVICE) {
                while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
                        SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
@@ -927,35 +902,11 @@ static int init_nic(struct s2io_nic *nic)
                        dtx_cnt++;
                }
        } else {
-               while (1) {
-                     dtx_cfg:
-                       while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
-                               if (xena_dtx_cfg[dtx_cnt] == SWITCH_SIGN) {
-                                       dtx_cnt++;
-                                       goto mdio_cfg;
-                               }
-                               SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
-                                                 &bar0->dtx_control, UF);
-                               val64 = readq(&bar0->dtx_control);
-                               dtx_cnt++;
-                       }
-                     mdio_cfg:
-                       while (xena_mdio_cfg[mdio_cnt] != END_SIGN) {
-                               if (xena_mdio_cfg[mdio_cnt] == SWITCH_SIGN) {
-                                       mdio_cnt++;
-                                       goto dtx_cfg;
-                               }
-                               SPECIAL_REG_WRITE(xena_mdio_cfg[mdio_cnt],
-                                                 &bar0->mdio_control, UF);
-                               val64 = readq(&bar0->mdio_control);
-                               mdio_cnt++;
-                       }
-                       if ((xena_dtx_cfg[dtx_cnt] == END_SIGN) &&
-                           (xena_mdio_cfg[mdio_cnt] == END_SIGN)) {
-                               break;
-                       } else {
-                               goto dtx_cfg;
-                       }
+               while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
+                       SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
+                                         &bar0->dtx_control, UF);
+                       val64 = readq(&bar0->dtx_control);
+                       dtx_cnt++;
                }
        }
 
@@ -1565,11 +1516,9 @@ static int init_nic(struct s2io_nic *nic)
                val64 &= ~(BIT(13)|BIT(14)|BIT(15));
                writeq(val64, &bar0->pic_control2);
        }
-
-       /* Setting Link stability period to 64 ms */ 
-       if (nic->device_type == XFRAME_II_DEVICE) {
-               val64 = MISC_LINK_STABILITY_PRD(3);
-               writeq(val64, &bar0->misc_control);
+       if (strstr(nic->product_name, "CX4")) {
+               val64 = TMAC_AVG_IPG(0x17);
+               writeq(val64, &bar0->tmac_avg_ipg);
        }
 
        return SUCCESS;
@@ -2034,6 +1983,13 @@ static int start_nic(struct s2io_nic *nic)
        val64 |= ADAPTER_EOI_TX_ON;
        writeq(val64, &bar0->adapter_control);
 
+       if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
+               /*
+                * Dont see link state interrupts initally on some switches,
+                * so directly scheduling the link state task here.
+                */
+               schedule_work(&nic->set_link_task);
+       }
        /* SXE-002: Initialize link and activity LED */
        subid = nic->pdev->subsystem_device;
        if (((subid & 0xFF) >= 0x07) &&
@@ -2045,12 +2001,6 @@ static int start_nic(struct s2io_nic *nic)
                writeq(val64, (void __iomem *)bar0 + 0x2700);
        }
 
-       /*
-        * Don't see link state interrupts on certain switches, so
-        * directly scheduling a link state task from here.
-        */
-       schedule_work(&nic->set_link_task);
-
        return SUCCESS;
 }
 /**
@@ -2569,7 +2519,8 @@ static int s2io_poll(struct net_device *dev, int *budget)
                }
        }
        /* Re enable the Rx interrupts. */
-       en_dis_able_nic_intrs(nic, RX_TRAFFIC_INTR, ENABLE_INTRS);
+       writeq(0x0, &bar0->rx_traffic_mask);
+       val64 = readl(&bar0->rx_traffic_mask);
        atomic_dec(&nic->isr_cnt);
        return 0;
 
@@ -2881,23 +2832,26 @@ static void alarm_intr_handler(struct s2io_nic *nic)
  *   SUCCESS on success and FAILURE on failure.
  */
 
-static int wait_for_cmd_complete(nic_t * sp)
+static int wait_for_cmd_complete(void *addr, u64 busy_bit)
 {
-       XENA_dev_config_t __iomem *bar0 = sp->bar0;
        int ret = FAILURE, cnt = 0;
        u64 val64;
 
        while (TRUE) {
-               val64 = readq(&bar0->rmac_addr_cmd_mem);
-               if (!(val64 & RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
+               val64 = readq(addr);
+               if (!(val64 & busy_bit)) {
                        ret = SUCCESS;
                        break;
                }
-               msleep(50);
+
+               if(in_interrupt())
+                       mdelay(50);
+               else
+                       msleep(50);
+
                if (cnt++ > 10)
                        break;
        }
-
        return ret;
 }
 
@@ -2936,6 +2890,9 @@ static void s2io_reset(nic_t * sp)
         * PCI write to sw_reset register is done by this time.
         */
        msleep(250);
+       if (strstr(sp->product_name, "CX4")) {
+               msleep(750);
+       }
 
        /* Restore the PCI state saved during initialization. */
        pci_restore_state(sp->pdev);
@@ -3154,7 +3111,7 @@ static void restore_xmsi_data(nic_t *nic)
        u64 val64;
        int i;
 
-       for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
+       for (i=0; i< nic->avail_msix_vectors; i++) {
                writeq(nic->msix_info[i].addr, &bar0->xmsi_address);
                writeq(nic->msix_info[i].data, &bar0->xmsi_data);
                val64 = (BIT(7) | BIT(15) | vBIT(i, 26, 6));
@@ -3173,7 +3130,7 @@ static void store_xmsi_data(nic_t *nic)
        int i;
 
        /* Store and display */
-       for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
+       for (i=0; i< nic->avail_msix_vectors; i++) {
                val64 = (BIT(15) | vBIT(i, 26, 6));
                writeq(val64, &bar0->xmsi_access);
                if (wait_for_msix_trans(nic, i)) {
@@ -3301,15 +3258,24 @@ static int s2io_enable_msi_x(nic_t *nic)
                writeq(tx_mat, &bar0->tx_mat0_n[7]);
        }
 
+       nic->avail_msix_vectors = 0;
        ret = pci_enable_msix(nic->pdev, nic->entries, MAX_REQUESTED_MSI_X);
+       /* We fail init if error or we get less vectors than min required */
+       if (ret >= (nic->config.tx_fifo_num + nic->config.rx_ring_num + 1)) {
+               nic->avail_msix_vectors = ret;
+               ret = pci_enable_msix(nic->pdev, nic->entries, ret);
+       }
        if (ret) {
                DBG_PRINT(ERR_DBG, "%s: Enabling MSIX failed\n", nic->dev->name);
                kfree(nic->entries);
                kfree(nic->s2io_entries);
                nic->entries = NULL;
                nic->s2io_entries = NULL;
+               nic->avail_msix_vectors = 0;
                return -ENOMEM;
        }
+       if (!nic->avail_msix_vectors)
+               nic->avail_msix_vectors = MAX_REQUESTED_MSI_X;
 
        /*
         * To enable MSI-X, MSI also needs to be enabled, due to a bug
@@ -3342,8 +3308,6 @@ static int s2io_open(struct net_device *dev)
 {
        nic_t *sp = dev->priv;
        int err = 0;
-       int i;
-       u16 msi_control; /* Temp variable */
 
        /*
         * Make sure you have link off by default every time
@@ -3353,11 +3317,14 @@ static int s2io_open(struct net_device *dev)
        sp->last_link_state = 0;
 
        /* Initialize H/W and enable interrupts */
-       if (s2io_card_up(sp)) {
+       err = s2io_card_up(sp);
+       if (err) {
                DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
                          dev->name);
-               err = -ENODEV;
-               goto hw_init_failed;
+               if (err == -ENODEV)
+                       goto hw_init_failed;
+               else
+                       goto hw_enable_failed;
        }
 
        /* Store the values of the MSIX table in the nic_t structure */
@@ -3374,6 +3341,8 @@ failed\n", dev->name);
                }
        }
        if (sp->intr_type == MSI_X) {
+               int i;
+
                for (i=1; (sp->s2io_entries[i].in_use == MSIX_FLG); i++) {
                        if (sp->s2io_entries[i].type == MSIX_FIFO_TYPE) {
                                sprintf(sp->desc1, "%s:MSI-X-%d-TX",
@@ -3426,24 +3395,25 @@ setting_mac_address_failed:
 isr_registration_failed:
        del_timer_sync(&sp->alarm_timer);
        if (sp->intr_type == MSI_X) {
-               if (sp->device_type == XFRAME_II_DEVICE) {
-                       for (i=1; (sp->s2io_entries[i].in_use == 
+               int i;
+               u16 msi_control; /* Temp variable */
+               for (i=1; (sp->s2io_entries[i].in_use == 
                                MSIX_REGISTERED_SUCCESS); i++) {
-                               int vector = sp->entries[i].vector;
-                               void *arg = sp->s2io_entries[i].arg;
-
-                               free_irq(vector, arg);
-                       }
-                       pci_disable_msix(sp->pdev);
+                       int vector = sp->entries[i].vector;
+                       void *arg = sp->s2io_entries[i].arg;
 
-                       /* Temp */
-                       pci_read_config_word(sp->pdev, 0x42, &msi_control);
-                       msi_control &= 0xFFFE; /* Disable MSI */
-                       pci_write_config_word(sp->pdev, 0x42, msi_control);
+                       free_irq(vector, arg);
                }
+               pci_disable_msix(sp->pdev);
+
+               /* Temp */
+               pci_read_config_word(sp->pdev, 0x42, &msi_control);
+               msi_control &= 0xFFFE; /* Disable MSI */
+               pci_write_config_word(sp->pdev, 0x42, msi_control);
        }
        else if (sp->intr_type == MSI)
                pci_disable_msi(sp->pdev);
+hw_enable_failed:
        s2io_reset(sp);
 hw_init_failed:
        if (sp->intr_type == MSI_X) {
@@ -3471,35 +3441,12 @@ hw_init_failed:
 static int s2io_close(struct net_device *dev)
 {
        nic_t *sp = dev->priv;
-       int i;
-       u16 msi_control;
 
        flush_scheduled_work();
        netif_stop_queue(dev);
        /* Reset card, kill tasklet and free Tx and Rx buffers. */
-       s2io_card_down(sp);
-
-       if (sp->intr_type == MSI_X) {
-               if (sp->device_type == XFRAME_II_DEVICE) {
-                       for (i=1; (sp->s2io_entries[i].in_use == 
-                                       MSIX_REGISTERED_SUCCESS); i++) {
-                               int vector = sp->entries[i].vector;
-                               void *arg = sp->s2io_entries[i].arg;
-
-                               free_irq(vector, arg);
-                       }
-                       pci_read_config_word(sp->pdev, 0x42, &msi_control);
-                       msi_control &= 0xFFFE; /* Disable MSI */
-                       pci_write_config_word(sp->pdev, 0x42, msi_control);
+       s2io_card_down(sp, 1);
 
-                       pci_disable_msix(sp->pdev);
-               }
-       }
-       else {
-               free_irq(sp->pdev->irq, dev);
-               if (sp->intr_type == MSI)
-                       pci_disable_msi(sp->pdev);
-       }       
        sp->device_close_flag = TRUE;   /* Device is shut down. */
        return 0;
 }
@@ -3825,41 +3772,56 @@ static void s2io_txpic_intr_handle(nic_t *sp)
                val64 = readq(&bar0->gpio_int_reg);
                if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
                    (val64 & GPIO_INT_REG_LINK_UP)) {
+                       /*
+                        * This is unstable state so clear both up/down
+                        * interrupt and adapter to re-evaluate the link state.
+                        */
                        val64 |=  GPIO_INT_REG_LINK_DOWN;
                        val64 |= GPIO_INT_REG_LINK_UP;
                        writeq(val64, &bar0->gpio_int_reg);
-                       goto masking;
-               }
-
-               if (((sp->last_link_state == LINK_UP) &&
-                       (val64 & GPIO_INT_REG_LINK_DOWN)) ||
-               ((sp->last_link_state == LINK_DOWN) &&
-               (val64 & GPIO_INT_REG_LINK_UP))) {
                        val64 = readq(&bar0->gpio_int_mask);
-                       val64 |=  GPIO_INT_MASK_LINK_DOWN;
-                       val64 |= GPIO_INT_MASK_LINK_UP;
+                       val64 &= ~(GPIO_INT_MASK_LINK_UP |
+                                  GPIO_INT_MASK_LINK_DOWN);
                        writeq(val64, &bar0->gpio_int_mask);
-                       s2io_set_link((unsigned long)sp);
                }
-masking:
-               if (sp->last_link_state == LINK_UP) {
-                       /*enable down interrupt */
-                       val64 = readq(&bar0->gpio_int_mask);
-                       /* unmasks link down intr */
-                       val64 &=  ~GPIO_INT_MASK_LINK_DOWN;
-                       /* masks link up intr */
-                       val64 |= GPIO_INT_MASK_LINK_UP;
-                       writeq(val64, &bar0->gpio_int_mask);
-               } else {
-                       /*enable UP Interrupt */
-                       val64 = readq(&bar0->gpio_int_mask);
-                       /* unmasks link up interrupt */
-                       val64 &= ~GPIO_INT_MASK_LINK_UP;
-                       /* masks link down interrupt */
-                       val64 |=  GPIO_INT_MASK_LINK_DOWN;
-                       writeq(val64, &bar0->gpio_int_mask);
+               else if (val64 & GPIO_INT_REG_LINK_UP) {
+                       val64 = readq(&bar0->adapter_status);
+                       if (verify_xena_quiescence(sp, val64,
+                                                  sp->device_enabled_once)) {
+                               /* Enable Adapter */
+                               val64 = readq(&bar0->adapter_control);
+                               val64 |= ADAPTER_CNTL_EN;
+                               writeq(val64, &bar0->adapter_control);
+                               val64 |= ADAPTER_LED_ON;
+                               writeq(val64, &bar0->adapter_control);
+                               if (!sp->device_enabled_once)
+                                       sp->device_enabled_once = 1;
+
+                               s2io_link(sp, LINK_UP);
+                               /*
+                                * unmask link down interrupt and mask link-up
+                                * intr
+                                */
+                               val64 = readq(&bar0->gpio_int_mask);
+                               val64 &= ~GPIO_INT_MASK_LINK_DOWN;
+                               val64 |= GPIO_INT_MASK_LINK_UP;
+                               writeq(val64, &bar0->gpio_int_mask);
+
+                       }
+               }else if (val64 & GPIO_INT_REG_LINK_DOWN) {
+                       val64 = readq(&bar0->adapter_status);
+                       if (verify_xena_quiescence(sp, val64,
+                                                  sp->device_enabled_once)) {
+                               s2io_link(sp, LINK_DOWN);
+                               /* Link is down so unmaks link up interrupt */
+                               val64 = readq(&bar0->gpio_int_mask);
+                               val64 &= ~GPIO_INT_MASK_LINK_UP;
+                               val64 |= GPIO_INT_MASK_LINK_DOWN;
+                               writeq(val64, &bar0->gpio_int_mask);
+                       }
                }
        }
+       val64 = readq(&bar0->gpio_int_mask);
 }
 
 /**
@@ -4080,7 +4042,8 @@ static void s2io_set_multicast(struct net_device *dev)
                    RMAC_ADDR_CMD_MEM_OFFSET(MAC_MC_ALL_MC_ADDR_OFFSET);
                writeq(val64, &bar0->rmac_addr_cmd_mem);
                /* Wait till command completes */
-               wait_for_cmd_complete(sp);
+               wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+                                     RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING);
 
                sp->m_cast_flg = 1;
                sp->all_multi_pos = MAC_MC_ALL_MC_ADDR_OFFSET;
@@ -4095,7 +4058,8 @@ static void s2io_set_multicast(struct net_device *dev)
                    RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
                writeq(val64, &bar0->rmac_addr_cmd_mem);
                /* Wait till command completes */
-               wait_for_cmd_complete(sp);
+               wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+                                     RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING);
 
                sp->m_cast_flg = 0;
                sp->all_multi_pos = 0;
@@ -4160,7 +4124,8 @@ static void s2io_set_multicast(struct net_device *dev)
                        writeq(val64, &bar0->rmac_addr_cmd_mem);
 
                        /* Wait for command completes */
-                       if (wait_for_cmd_complete(sp)) {
+                       if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+                                     RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
                                DBG_PRINT(ERR_DBG, "%s: Adding ",
                                          dev->name);
                                DBG_PRINT(ERR_DBG, "Multicasts failed\n");
@@ -4190,7 +4155,8 @@ static void s2io_set_multicast(struct net_device *dev)
                        writeq(val64, &bar0->rmac_addr_cmd_mem);
 
                        /* Wait for command completes */
-                       if (wait_for_cmd_complete(sp)) {
+                       if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+                                     RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
                                DBG_PRINT(ERR_DBG, "%s: Adding ",
                                          dev->name);
                                DBG_PRINT(ERR_DBG, "Multicasts failed\n");
@@ -4235,7 +4201,8 @@ static int s2io_set_mac_addr(struct net_device *dev, u8 * addr)
            RMAC_ADDR_CMD_MEM_OFFSET(0);
        writeq(val64, &bar0->rmac_addr_cmd_mem);
        /* Wait till command completes */
-       if (wait_for_cmd_complete(sp)) {
+       if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+                     RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
                DBG_PRINT(ERR_DBG, "%s: set_mac_addr failed\n", dev->name);
                return FAILURE;
        }
@@ -4632,7 +4599,6 @@ static int write_eeprom(nic_t * sp, int off, u64 data, int cnt)
        }
        return ret;
 }
-
 static void s2io_vpd_read(nic_t *nic)
 {
        u8 vpd_data[256],data;
@@ -4983,8 +4949,10 @@ static int s2io_link_test(nic_t * sp, uint64_t * data)
        u64 val64;
 
        val64 = readq(&bar0->adapter_status);
-       if (val64 & ADAPTER_STATUS_RMAC_LOCAL_FAULT)
+       if(!(LINK_IS_UP(val64)))
                *data = 1;
+       else
+               *data = 0;
 
        return 0;
 }
@@ -5403,7 +5371,7 @@ static int s2io_change_mtu(struct net_device *dev, int new_mtu)
 
        dev->mtu = new_mtu;
        if (netif_running(dev)) {
-               s2io_card_down(sp);
+               s2io_card_down(sp, 0);
                netif_stop_queue(dev);
                if (s2io_card_up(sp)) {
                        DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
@@ -5541,12 +5509,13 @@ static void s2io_set_link(unsigned long data)
        clear_bit(0, &(nic->link_state));
 }
 
-static void s2io_card_down(nic_t * sp)
+static void s2io_card_down(nic_t * sp, int flag)
 {
        int cnt = 0;
        XENA_dev_config_t __iomem *bar0 = sp->bar0;
        unsigned long flags;
        register u64 val64 = 0;
+       struct net_device *dev = sp->dev;
 
        del_timer_sync(&sp->alarm_timer);
        /* If s2io_set_link task is executing, wait till it completes. */
@@ -5557,6 +5526,36 @@ static void s2io_card_down(nic_t * sp)
 
        /* disable Tx and Rx traffic on the NIC */
        stop_nic(sp);
+       if (flag) {
+               if (sp->intr_type == MSI_X) {
+                       int i;
+                       u16 msi_control;
+
+                       for (i=1; (sp->s2io_entries[i].in_use ==
+                               MSIX_REGISTERED_SUCCESS); i++) {
+                               int vector = sp->entries[i].vector;
+                               void *arg = sp->s2io_entries[i].arg;
+
+                               free_irq(vector, arg);
+                       }
+                       pci_read_config_word(sp->pdev, 0x42, &msi_control);
+                       msi_control &= 0xFFFE; /* Disable MSI */
+                       pci_write_config_word(sp->pdev, 0x42, msi_control);
+                       pci_disable_msix(sp->pdev);
+               } else {
+                       free_irq(sp->pdev->irq, dev);
+                       if (sp->intr_type == MSI)
+                               pci_disable_msi(sp->pdev);
+               }
+       }
+       /* Waiting till all Interrupt handlers are complete */
+       cnt = 0;
+       do {
+               msleep(10);
+               if (!atomic_read(&sp->isr_cnt))
+                       break;
+               cnt++;
+       } while(cnt < 5);
 
        /* Kill tasklet. */
        tasklet_kill(&sp->task);
@@ -5580,15 +5579,6 @@ static void s2io_card_down(nic_t * sp)
        } while (1);
        s2io_reset(sp);
 
-       /* Waiting till all Interrupt handlers are complete */
-       cnt = 0;
-       do {
-               msleep(10);
-               if (!atomic_read(&sp->isr_cnt))
-                       break;
-               cnt++;
-       } while(cnt < 5);
-
        spin_lock_irqsave(&sp->tx_lock, flags);
        /* Free all Tx buffers */
        free_tx_buffers(sp);
@@ -5689,7 +5679,7 @@ static void s2io_restart_nic(unsigned long data)
        struct net_device *dev = (struct net_device *) data;
        nic_t *sp = dev->priv;
 
-       s2io_card_down(sp);
+       s2io_card_down(sp, 0);
        if (s2io_card_up(sp)) {
                DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
                          dev->name);
@@ -5751,6 +5741,7 @@ static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp)
        lro_t *lro;
 
        skb->dev = dev;
+
        if (err) {
                /*
                * Drop the packet if bad transfer code. Exception being
@@ -5853,6 +5844,9 @@ static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp)
                                                clear_lro_session(lro);
                                                goto send_up;
                                        case 0: /* sessions exceeded */
+                                       case -1: /* non-TCP or not
+                                                 * L2 aggregatable
+                                                 */
                                        case 5: /*
                                                 * First pkt in session not
                                                 * L3/L4 aggregatable
@@ -6351,8 +6345,8 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
        val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
            RMAC_ADDR_CMD_MEM_OFFSET(0 + MAC_MAC_ADDR_START_OFFSET);
        writeq(val64, &bar0->rmac_addr_cmd_mem);
-       wait_for_cmd_complete(sp);
-
+       wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+                     RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING);
        tmp64 = readq(&bar0->rmac_addr_data0_mem);
        mac_down = (u32) tmp64;
        mac_up = (u32) (tmp64 >> 32);
index a83a1d85f72e6eaefc12525f92c7e97ee20141e5..fb46a4fed334f6d98db52b974aaa3e49fb39b176 100644 (file)
@@ -661,8 +661,8 @@ typedef struct {
 /* Default Tunable parameters of the NIC. */
 #define DEFAULT_FIFO_0_LEN 4096
 #define DEFAULT_FIFO_1_7_LEN 512
-#define SMALL_BLK_CNT   30
-#define LARGE_BLK_CNT   100
+#define SMALL_BLK_CNT  30
+#define LARGE_BLK_CNT  100
 
 /*
  * Structure to keep track of the MSI-X vectors and the corresponding
@@ -733,7 +733,7 @@ struct s2io_nic {
        int device_close_flag;
        int device_enabled_once;
 
-       char name[50];
+       char name[60];
        struct tasklet_struct task;
        volatile unsigned long tasklet_status;
 
@@ -804,6 +804,8 @@ struct s2io_nic {
        char desc1[35];
        char desc2[35];
 
+       int avail_msix_vectors; /* No. of MSI-X vectors granted by system */
+
        struct msix_info_st msix_info[0x3f];
 
 #define XFRAME_I_DEVICE                1
@@ -851,28 +853,32 @@ static inline void writeq(u64 val, void __iomem *addr)
        writel((u32) (val), addr);
        writel((u32) (val >> 32), (addr + 4));
 }
+#endif
 
-/* In 32 bit modes, some registers have to be written in a
- * particular order to expect correct hardware operation. The
- * macro SPECIAL_REG_WRITE is used to perform such ordered
- * writes. Defines UF (Upper First) and LF (Lower First) will
- * be used to specify the required write order.
+/* 
+ * Some registers have to be written in a particular order to 
+ * expect correct hardware operation. The macro SPECIAL_REG_WRITE 
+ * is used to perform such ordered writes. Defines UF (Upper First) 
+ * and LF (Lower First) will be used to specify the required write order.
  */
 #define UF     1
 #define LF     2
 static inline void SPECIAL_REG_WRITE(u64 val, void __iomem *addr, int order)
 {
+       u32 ret;
+
        if (order == LF) {
                writel((u32) (val), addr);
+               ret = readl(addr);
                writel((u32) (val >> 32), (addr + 4));
+               ret = readl(addr + 4);
        } else {
                writel((u32) (val >> 32), (addr + 4));
+               ret = readl(addr + 4);
                writel((u32) (val), addr);
+               ret = readl(addr);
        }
 }
-#else
-#define SPECIAL_REG_WRITE(val, addr, dummy) writeq(val, addr)
-#endif
 
 /*  Interrupt related values of Xena */
 
@@ -968,7 +974,7 @@ static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag);
 static struct ethtool_ops netdev_ethtool_ops;
 static void s2io_set_link(unsigned long data);
 static int s2io_set_swapper(nic_t * sp);
-static void s2io_card_down(nic_t *nic);
+static void s2io_card_down(nic_t *nic, int flag);
 static int s2io_card_up(nic_t *nic);
 static int get_xena_rev_id(struct pci_dev *pdev);
 static void restore_xmsi_data(nic_t *nic);