{
unsigned char status1, scratch, scratch2, scratch3;
unsigned char save_lcr, save_mcr;
+ struct uart_port *port = &up->port;
unsigned long flags;
- if (!up->port.iobase && !up->port.mapbase && !up->port.membase)
+ if (!port->iobase && !port->mapbase && !port->membase)
return;
DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ",
- serial_index(&up->port), up->port.iobase, up->port.membase);
+ serial_index(port), port->iobase, port->membase);
/*
* We really do need global IRQs disabled here - we're going to
* be frobbing the chips IRQ enable register to see if it exists.
*/
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
up->capabilities = 0;
up->bugs = 0;
- if (!(up->port.flags & UPF_BUGGY_UART)) {
+ if (!(port->flags & UPF_BUGGY_UART)) {
/*
* Do a simple existence test first; if we fail this,
* there's no point trying anything else.
* manufacturer would be stupid enough to design a board
* that conflicts with COM 1-4 --- we hope!
*/
- if (!(up->port.flags & UPF_SKIP_TEST)) {
+ if (!(port->flags & UPF_SKIP_TEST)) {
serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A);
status1 = serial_in(up, UART_MSR) & 0xF0;
serial_out(up, UART_MCR, save_mcr);
autoconfig_8250(up);
break;
case 1:
- up->port.type = PORT_UNKNOWN;
+ port->type = PORT_UNKNOWN;
break;
case 2:
- up->port.type = PORT_16550;
+ port->type = PORT_16550;
break;
case 3:
autoconfig_16550a(up);
/*
* Only probe for RSA ports if we got the region.
*/
- if (up->port.type == PORT_16550A && probeflags & PROBE_RSA) {
+ if (port->type == PORT_16550A && probeflags & PROBE_RSA) {
int i;
for (i = 0 ; i < probe_rsa_count; ++i) {
- if (probe_rsa[i] == up->port.iobase &&
- __enable_rsa(up)) {
- up->port.type = PORT_RSA;
+ if (probe_rsa[i] == port->iobase && __enable_rsa(up)) {
+ port->type = PORT_RSA;
break;
}
}
serial_out(up, UART_LCR, save_lcr);
- if (up->capabilities != uart_config[up->port.type].flags) {
+ if (up->capabilities != uart_config[port->type].flags) {
printk(KERN_WARNING
"ttyS%d: detected caps %08x should be %08x\n",
- serial_index(&up->port), up->capabilities,
- uart_config[up->port.type].flags);
+ serial_index(port), up->capabilities,
+ uart_config[port->type].flags);
}
- up->port.fifosize = uart_config[up->port.type].fifo_size;
- up->capabilities = uart_config[up->port.type].flags;
- up->tx_loadsz = uart_config[up->port.type].tx_loadsz;
+ port->fifosize = uart_config[up->port.type].fifo_size;
+ up->capabilities = uart_config[port->type].flags;
+ up->tx_loadsz = uart_config[port->type].tx_loadsz;
- if (up->port.type == PORT_UNKNOWN)
+ if (port->type == PORT_UNKNOWN)
goto out;
/*
* Reset the UART.
*/
#ifdef CONFIG_SERIAL_8250_RSA
- if (up->port.type == PORT_RSA)
+ if (port->type == PORT_RSA)
serial_out(up, UART_RSA_FRR, 0);
#endif
serial_out(up, UART_MCR, save_mcr);
serial_out(up, UART_IER, 0);
out:
- spin_unlock_irqrestore(&up->port.lock, flags);
- DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
+ spin_unlock_irqrestore(&port->lock, flags);
+ DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name);
}
static void autoconfig_irq(struct uart_8250_port *up)
{
+ struct uart_port *port = &up->port;
unsigned char save_mcr, save_ier;
unsigned char save_ICP = 0;
unsigned int ICP = 0;
unsigned long irqs;
int irq;
- if (up->port.flags & UPF_FOURPORT) {
- ICP = (up->port.iobase & 0xfe0) | 0x1f;
+ if (port->flags & UPF_FOURPORT) {
+ ICP = (port->iobase & 0xfe0) | 0x1f;
save_ICP = inb_p(ICP);
outb_p(0x80, ICP);
inb_p(ICP);
irqs = probe_irq_on();
serial_out(up, UART_MCR, 0);
udelay(10);
- if (up->port.flags & UPF_FOURPORT) {
+ if (port->flags & UPF_FOURPORT) {
serial_out(up, UART_MCR,
UART_MCR_DTR | UART_MCR_RTS);
} else {
serial_out(up, UART_MCR, save_mcr);
serial_out(up, UART_IER, save_ier);
- if (up->port.flags & UPF_FOURPORT)
+ if (port->flags & UPF_FOURPORT)
outb_p(save_ICP, ICP);
- up->port.irq = (irq > 0) ? irq : 0;
+ port->irq = (irq > 0) ? irq : 0;
}
static inline void __stop_tx(struct uart_8250_port *p)
/*
* We really want to stop the transmitter from sending.
*/
- if (up->port.type == PORT_16C950) {
+ if (port->type == PORT_16C950) {
up->acr |= UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
unsigned char lsr;
lsr = serial_in(up, UART_LSR);
up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
- if ((up->port.type == PORT_RM9000) ?
+ if ((port->type == PORT_RM9000) ?
(lsr & UART_LSR_THRE) :
(lsr & UART_LSR_TEMT))
serial8250_tx_chars(up);
/*
* Re-enable the transmitter if we disabled it.
*/
- if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
+ if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
up->acr &= ~UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
unsigned char
serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
{
- struct tty_struct *tty = up->port.state->port.tty;
+ struct uart_port *port = &up->port;
+ struct tty_struct *tty = port->state->port.tty;
unsigned char ch;
int max_count = 256;
char flag;
ch = 0;
flag = TTY_NORMAL;
- up->port.icount.rx++;
+ port->icount.rx++;
lsr |= up->lsr_saved_flags;
up->lsr_saved_flags = 0;
*/
if (lsr & UART_LSR_BI) {
lsr &= ~(UART_LSR_FE | UART_LSR_PE);
- up->port.icount.brk++;
+ port->icount.brk++;
/*
* If tegra port then clear the rx fifo to
* accept another break/character.
*/
- if (up->port.type == PORT_TEGRA)
+ if (port->type == PORT_TEGRA)
clear_rx_fifo(up);
/*
* may get masked by ignore_status_mask
* or read_status_mask.
*/
- if (uart_handle_break(&up->port))
+ if (uart_handle_break(port))
goto ignore_char;
} else if (lsr & UART_LSR_PE)
- up->port.icount.parity++;
+ port->icount.parity++;
else if (lsr & UART_LSR_FE)
- up->port.icount.frame++;
+ port->icount.frame++;
if (lsr & UART_LSR_OE)
- up->port.icount.overrun++;
+ port->icount.overrun++;
/*
* Mask off conditions which should be ignored.
*/
- lsr &= up->port.read_status_mask;
+ lsr &= port->read_status_mask;
if (lsr & UART_LSR_BI) {
DEBUG_INTR("handling break....");
else if (lsr & UART_LSR_FE)
flag = TTY_FRAME;
}
- if (uart_handle_sysrq_char(&up->port, ch))
+ if (uart_handle_sysrq_char(port, ch))
goto ignore_char;
- uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
+ uart_insert_char(port, lsr, UART_LSR_OE, ch, flag);
ignore_char:
lsr = serial_in(up, UART_LSR);
} while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (max_count-- > 0));
- spin_unlock(&up->port.lock);
+ spin_unlock(&port->lock);
tty_flip_buffer_push(tty);
- spin_lock(&up->port.lock);
+ spin_lock(&port->lock);
return lsr;
}
EXPORT_SYMBOL_GPL(serial8250_rx_chars);
void serial8250_tx_chars(struct uart_8250_port *up)
{
- struct circ_buf *xmit = &up->port.state->xmit;
+ struct uart_port *port = &up->port;
+ struct circ_buf *xmit = &port->state->xmit;
int count;
- if (up->port.x_char) {
- serial_out(up, UART_TX, up->port.x_char);
- up->port.icount.tx++;
- up->port.x_char = 0;
+ if (port->x_char) {
+ serial_out(up, UART_TX, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
return;
}
- if (uart_tx_stopped(&up->port)) {
- serial8250_stop_tx(&up->port);
+ if (uart_tx_stopped(port)) {
+ serial8250_stop_tx(port);
return;
}
if (uart_circ_empty(xmit)) {
do {
serial_out(up, UART_TX, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- up->port.icount.tx++;
+ port->icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
- uart_write_wakeup(&up->port);
+ uart_write_wakeup(port);
DEBUG_INTR("THRE...");
unsigned int serial8250_modem_status(struct uart_8250_port *up)
{
+ struct uart_port *port = &up->port;
unsigned int status = serial_in(up, UART_MSR);
status |= up->msr_saved_flags;
up->msr_saved_flags = 0;
if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
- up->port.state != NULL) {
+ port->state != NULL) {
if (status & UART_MSR_TERI)
- up->port.icount.rng++;
+ port->icount.rng++;
if (status & UART_MSR_DDSR)
- up->port.icount.dsr++;
+ port->icount.dsr++;
if (status & UART_MSR_DDCD)
- uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
+ uart_handle_dcd_change(port, status & UART_MSR_DCD);
if (status & UART_MSR_DCTS)
- uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
+ uart_handle_cts_change(port, status & UART_MSR_CTS);
- wake_up_interruptible(&up->port.state->port.delta_msr_wait);
+ wake_up_interruptible(&port->state->port.delta_msr_wait);
}
return status;
if (iir & UART_IIR_NO_INT)
return 0;
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
status = serial_in(up, UART_LSR);
if (status & UART_LSR_THRE)
serial8250_tx_chars(up);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ spin_unlock_irqrestore(&port->lock, flags);
return 1;
}
EXPORT_SYMBOL_GPL(serial8250_handle_irq);
unsigned long flags;
unsigned int lsr;
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
lsr = serial_in(up, UART_LSR);
up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
- spin_unlock_irqrestore(&up->port.lock, flags);
+ spin_unlock_irqrestore(&port->lock, flags);
return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
}
container_of(port, struct uart_8250_port, port);
unsigned long flags;
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
if (break_state == -1)
up->lcr |= UART_LCR_SBC;
else
up->lcr &= ~UART_LCR_SBC;
serial_out(up, UART_LCR, up->lcr);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ spin_unlock_irqrestore(&port->lock, flags);
}
/*
unsigned char lsr, iir;
int retval;
- up->port.fifosize = uart_config[up->port.type].fifo_size;
+ port->fifosize = uart_config[up->port.type].fifo_size;
up->tx_loadsz = uart_config[up->port.type].tx_loadsz;
up->capabilities = uart_config[up->port.type].flags;
up->mcr = 0;
- if (up->port.iotype != up->cur_iotype)
+ if (port->iotype != up->cur_iotype)
set_io_from_upio(port);
- if (up->port.type == PORT_16C950) {
+ if (port->type == PORT_16C950) {
/* Wake up and initialize UART */
up->acr = 0;
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
* if it is, then bail out, because there's likely no UART
* here.
*/
- if (!(up->port.flags & UPF_BUGGY_UART) &&
+ if (!(port->flags & UPF_BUGGY_UART) &&
(serial_in(up, UART_LSR) == 0xff)) {
printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
- serial_index(&up->port));
+ serial_index(port));
return -ENODEV;
}
/*
* For a XR16C850, we need to set the trigger levels
*/
- if (up->port.type == PORT_16850) {
+ if (port->type == PORT_16850) {
unsigned char fctr;
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_LCR, 0);
}
- if (up->port.irq) {
+ if (port->irq) {
unsigned char iir1;
/*
* Test for UARTs that do not reassert THRE when the
* the interrupt is enabled. Delays are necessary to
* allow register changes to become visible.
*/
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
if (up->port.irqflags & IRQF_SHARED)
- disable_irq_nosync(up->port.irq);
+ disable_irq_nosync(port->irq);
wait_for_xmitr(up, UART_LSR_THRE);
serial_out_sync(up, UART_IER, UART_IER_THRI);
iir = serial_in(up, UART_IIR);
serial_out(up, UART_IER, 0);
- if (up->port.irqflags & IRQF_SHARED)
- enable_irq(up->port.irq);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ if (port->irqflags & IRQF_SHARED)
+ enable_irq(port->irq);
+ spin_unlock_irqrestore(&port->lock, flags);
/*
* If the interrupt is not reasserted, setup a timer to
* hardware interrupt, we use a timer-based system. The original
* driver used to do this with IRQ0.
*/
- if (!up->port.irq) {
+ if (!port->irq) {
up->timer.data = (unsigned long)up;
mod_timer(&up->timer, jiffies + uart_poll_timeout(port));
} else {
*/
serial_out(up, UART_LCR, UART_LCR_WLEN8);
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
if (up->port.flags & UPF_FOURPORT) {
if (!up->port.irq)
up->port.mctrl |= TIOCM_OUT1;
/*
* Most PC uarts need OUT2 raised to enable interrupts.
*/
- if (up->port.irq)
+ if (port->irq)
up->port.mctrl |= TIOCM_OUT2;
- serial8250_set_mctrl(&up->port, up->port.mctrl);
+ serial8250_set_mctrl(port, port->mctrl);
/* Serial over Lan (SoL) hack:
Intel 8257x Gigabit ethernet chips have a
}
dont_test_tx_en:
- spin_unlock_irqrestore(&up->port.lock, flags);
+ spin_unlock_irqrestore(&port->lock, flags);
/*
* Clear the interrupt registers again for luck, and clear the
up->ier = UART_IER_RLSI | UART_IER_RDI;
serial_out(up, UART_IER, up->ier);
- if (up->port.flags & UPF_FOURPORT) {
+ if (port->flags & UPF_FOURPORT) {
unsigned int icp;
/*
* Enable interrupts on the AST Fourport board
*/
- icp = (up->port.iobase & 0xfe0) | 0x01f;
+ icp = (port->iobase & 0xfe0) | 0x01f;
outb_p(0x80, icp);
inb_p(icp);
}
up->ier = 0;
serial_out(up, UART_IER, 0);
- spin_lock_irqsave(&up->port.lock, flags);
- if (up->port.flags & UPF_FOURPORT) {
+ spin_lock_irqsave(&port->lock, flags);
+ if (port->flags & UPF_FOURPORT) {
/* reset interrupts on the AST Fourport board */
- inb((up->port.iobase & 0xfe0) | 0x1f);
- up->port.mctrl |= TIOCM_OUT1;
+ inb((port->iobase & 0xfe0) | 0x1f);
+ port->mctrl |= TIOCM_OUT1;
} else
- up->port.mctrl &= ~TIOCM_OUT2;
+ port->mctrl &= ~TIOCM_OUT2;
- serial8250_set_mctrl(&up->port, up->port.mctrl);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ serial8250_set_mctrl(port, port->mctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
/*
* Disable break condition and FIFOs
del_timer_sync(&up->timer);
up->timer.function = serial8250_timeout;
- if (up->port.irq)
+ if (port->irq)
serial_unlink_irq_chain(up);
}
if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
quot++;
- if (up->capabilities & UART_CAP_FIFO && up->port.fifosize > 1) {
+ if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
if (baud < 2400)
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
else
- fcr = uart_config[up->port.type].fcr;
+ fcr = uart_config[port->type].fcr;
}
/*
* have sufficient FIFO entries for the latency of the remote
* UART to respond. IOW, at least 32 bytes of FIFO.
*/
- if (up->capabilities & UART_CAP_AFE && up->port.fifosize >= 32) {
+ if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) {
up->mcr &= ~UART_MCR_AFE;
if (termios->c_cflag & CRTSCTS)
up->mcr |= UART_MCR_AFE;
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
- spin_lock_irqsave(&up->port.lock, flags);
+ spin_lock_irqsave(&port->lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
- up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+ port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
- up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+ port->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
- up->port.read_status_mask |= UART_LSR_BI;
+ port->read_status_mask |= UART_LSR_BI;
/*
* Characteres to ignore
*/
- up->port.ignore_status_mask = 0;
+ port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
- up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
+ port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
- up->port.ignore_status_mask |= UART_LSR_BI;
+ port->ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
- up->port.ignore_status_mask |= UART_LSR_OE;
+ port->ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
- up->port.ignore_status_mask |= UART_LSR_DR;
+ port->ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
efr |= UART_EFR_CTS;
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- if (up->port.flags & UPF_EXAR_EFR)
+ if (port->flags & UPF_EXAR_EFR)
serial_out(up, UART_XR_EFR, efr);
else
serial_out(up, UART_EFR, efr);
* LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
* is written without DLAB set, this mode will be disabled.
*/
- if (up->port.type == PORT_16750)
+ if (port->type == PORT_16750)
serial_out(up, UART_FCR, fcr);
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
- if (up->port.type != PORT_16750) {
+ if (port->type != PORT_16750) {
if (fcr & UART_FCR_ENABLE_FIFO) {
/* emulated UARTs (Lucent Venus 167x) need two steps */
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
}
serial_out(up, UART_FCR, fcr); /* set fcr */
}
- serial8250_set_mctrl(&up->port, up->port.mctrl);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ serial8250_set_mctrl(port, port->mctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
/* Don't rewrite B0 */
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
static int serial8250_request_std_resource(struct uart_8250_port *up)
{
unsigned int size = serial8250_port_size(up);
+ struct uart_port *port = &up->port;
int ret = 0;
- switch (up->port.iotype) {
+ switch (port->iotype) {
case UPIO_AU:
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
- if (!up->port.mapbase)
+ if (!port->mapbase)
break;
- if (!request_mem_region(up->port.mapbase, size, "serial")) {
+ if (!request_mem_region(port->mapbase, size, "serial")) {
ret = -EBUSY;
break;
}
- if (up->port.flags & UPF_IOREMAP) {
- up->port.membase = ioremap_nocache(up->port.mapbase,
- size);
- if (!up->port.membase) {
- release_mem_region(up->port.mapbase, size);
+ if (port->flags & UPF_IOREMAP) {
+ port->membase = ioremap_nocache(port->mapbase, size);
+ if (!port->membase) {
+ release_mem_region(port->mapbase, size);
ret = -ENOMEM;
}
}
case UPIO_HUB6:
case UPIO_PORT:
- if (!request_region(up->port.iobase, size, "serial"))
+ if (!request_region(port->iobase, size, "serial"))
ret = -EBUSY;
break;
}
static void serial8250_release_std_resource(struct uart_8250_port *up)
{
unsigned int size = serial8250_port_size(up);
+ struct uart_port *port = &up->port;
- switch (up->port.iotype) {
+ switch (port->iotype) {
case UPIO_AU:
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
- if (!up->port.mapbase)
+ if (!port->mapbase)
break;
- if (up->port.flags & UPF_IOREMAP) {
- iounmap(up->port.membase);
- up->port.membase = NULL;
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
}
- release_mem_region(up->port.mapbase, size);
+ release_mem_region(port->mapbase, size);
break;
case UPIO_HUB6:
case UPIO_PORT:
- release_region(up->port.iobase, size);
+ release_region(port->iobase, size);
break;
}
}
{
unsigned long start = UART_RSA_BASE << up->port.regshift;
unsigned int size = 8 << up->port.regshift;
+ struct uart_port *port = &up->port;
int ret = -EINVAL;
- switch (up->port.iotype) {
+ switch (port->iotype) {
case UPIO_HUB6:
case UPIO_PORT:
- start += up->port.iobase;
+ start += port->iobase;
if (request_region(start, size, "serial-rsa"))
ret = 0;
else
{
unsigned long offset = UART_RSA_BASE << up->port.regshift;
unsigned int size = 8 << up->port.regshift;
+ struct uart_port *port = &up->port;
- switch (up->port.iotype) {
+ switch (port->iotype) {
case UPIO_HUB6:
case UPIO_PORT:
- release_region(up->port.iobase + offset, size);
+ release_region(port->iobase + offset, size);
break;
}
}
container_of(port, struct uart_8250_port, port);
serial8250_release_std_resource(up);
- if (up->port.type == PORT_RSA)
+ if (port->type == PORT_RSA)
serial8250_release_rsa_resource(up);
}
int ret = 0;
ret = serial8250_request_std_resource(up);
- if (ret == 0 && up->port.type == PORT_RSA) {
+ if (ret == 0 && port->type == PORT_RSA) {
ret = serial8250_request_rsa_resource(up);
if (ret < 0)
serial8250_release_std_resource(up);
if (ret < 0)
probeflags &= ~PROBE_RSA;
- if (up->port.iotype != up->cur_iotype)
+ if (port->iotype != up->cur_iotype)
set_io_from_upio(port);
if (flags & UART_CONFIG_TYPE)
autoconfig(up, probeflags);
/* if access method is AU, it is a 16550 with a quirk */
- if (up->port.type == PORT_16550A && up->port.iotype == UPIO_AU)
+ if (port->type == PORT_16550A && port->iotype == UPIO_AU)
up->bugs |= UART_BUG_NOMSR;
- if (up->port.type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
+ if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
autoconfig_irq(up);
- if (up->port.type != PORT_RSA && probeflags & PROBE_RSA)
+ if (port->type != PORT_RSA && probeflags & PROBE_RSA)
serial8250_release_rsa_resource(up);
- if (up->port.type == PORT_UNKNOWN)
+ if (port->type == PORT_UNKNOWN)
serial8250_release_std_resource(up);
}
for (i = 0; i < nr_uarts; i++) {
struct uart_8250_port *up = &serial8250_ports[i];
+ struct uart_port *port = &up->port;
- up->port.line = i;
- spin_lock_init(&up->port.lock);
+ port->line = i;
+ spin_lock_init(&port->lock);
init_timer(&up->timer);
up->timer.function = serial8250_timeout;
up->mcr_mask = ~ALPHA_KLUDGE_MCR;
up->mcr_force = ALPHA_KLUDGE_MCR;
- up->port.ops = &serial8250_pops;
+ port->ops = &serial8250_pops;
}
if (share_irqs)
for (i = 0, up = serial8250_ports;
i < ARRAY_SIZE(old_serial_port) && i < nr_uarts;
i++, up++) {
- up->port.iobase = old_serial_port[i].port;
- up->port.irq = irq_canonicalize(old_serial_port[i].irq);
- up->port.irqflags = old_serial_port[i].irqflags;
- up->port.uartclk = old_serial_port[i].baud_base * 16;
- up->port.flags = old_serial_port[i].flags;
- up->port.hub6 = old_serial_port[i].hub6;
- up->port.membase = old_serial_port[i].iomem_base;
- up->port.iotype = old_serial_port[i].io_type;
- up->port.regshift = old_serial_port[i].iomem_reg_shift;
- set_io_from_upio(&up->port);
- up->port.irqflags |= irqflag;
+ struct uart_port *port = &up->port;
+
+ port->iobase = old_serial_port[i].port;
+ port->irq = irq_canonicalize(old_serial_port[i].irq);
+ port->irqflags = old_serial_port[i].irqflags;
+ port->uartclk = old_serial_port[i].baud_base * 16;
+ port->flags = old_serial_port[i].flags;
+ port->hub6 = old_serial_port[i].hub6;
+ port->membase = old_serial_port[i].iomem_base;
+ port->iotype = old_serial_port[i].io_type;
+ port->regshift = old_serial_port[i].iomem_reg_shift;
+ set_io_from_upio(port);
+ port->irqflags |= irqflag;
if (serial8250_isa_config != NULL)
serial8250_isa_config(i, &up->port, &up->capabilities);
serial8250_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_8250_port *up = &serial8250_ports[co->index];
+ struct uart_port *port = &up->port;
unsigned long flags;
unsigned int ier;
int locked = 1;
touch_nmi_watchdog();
local_irq_save(flags);
- if (up->port.sysrq) {
+ if (port->sysrq) {
/* serial8250_handle_irq() already took the lock */
locked = 0;
} else if (oops_in_progress) {
- locked = spin_trylock(&up->port.lock);
+ locked = spin_trylock(&port->lock);
} else
- spin_lock(&up->port.lock);
+ spin_lock(&port->lock);
/*
* First save the IER then disable the interrupts
else
serial_out(up, UART_IER, 0);
- uart_console_write(&up->port, s, count, serial8250_console_putchar);
+ uart_console_write(port, s, count, serial8250_console_putchar);
/*
* Finally, wait for transmitter to become empty
serial8250_modem_status(up);
if (locked)
- spin_unlock(&up->port.lock);
+ spin_unlock(&port->lock);
local_irq_restore(flags);
}
void serial8250_resume_port(int line)
{
struct uart_8250_port *up = &serial8250_ports[line];
+ struct uart_port *port = &up->port;
if (up->capabilities & UART_NATSEMI) {
/* Ensure it's still in high speed mode */
ns16550a_goto_highspeed(up);
serial_out(up, UART_LCR, 0);
- up->port.uartclk = 921600*16;
+ port->uartclk = 921600*16;
}
- uart_resume_port(&serial8250_reg, &up->port);
+ uart_resume_port(&serial8250_reg, port);
}
/*
projects / firefly-linux-kernel-4.4.55.git / commitdiff