--- /dev/null
+Olimex i.MX Platforms Device Tree Bindings
+------------------------------------------
+
+i.MX23 Olinuxino Low Cost Board
+Required root node properties:
+ - compatible = "olimex,imx23-olinuxino", "fsl,imx23";
- AM335X EVM : Software Developement Board for AM335x
compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3"
+
+- AM335X Bone : Low cost community board
+ compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
+++ /dev/null
-Embedded Memory Controller
-
-Properties:
-- name : Should be emc
-- #address-cells : Should be 1
-- #size-cells : Should be 0
-- compatible : Should contain "nvidia,tegra20-emc".
-- reg : Offset and length of the register set for the device
-- nvidia,use-ram-code : If present, the sub-nodes will be addressed
- and chosen using the ramcode board selector. If omitted, only one
- set of tables can be present and said tables will be used
- irrespective of ram-code configuration.
-
-Child device nodes describe the memory settings for different configurations and clock rates.
-
-Example:
-
- emc@7000f400 {
- #address-cells = < 1 >;
- #size-cells = < 0 >;
- compatible = "nvidia,tegra20-emc";
- reg = <0x7000f4000 0x200>;
- }
-
-
-Embedded Memory Controller ram-code table
-
-If the emc node has the nvidia,use-ram-code property present, then the
-next level of nodes below the emc table are used to specify which settings
-apply for which ram-code settings.
-
-If the emc node lacks the nvidia,use-ram-code property, this level is omitted
-and the tables are stored directly under the emc node (see below).
-
-Properties:
-
-- name : Should be emc-tables
-- nvidia,ram-code : the binary representation of the ram-code board strappings
- for which this node (and children) are valid.
-
-
-
-Embedded Memory Controller configuration table
-
-This is a table containing the EMC register settings for the various
-operating speeds of the memory controller. They are always located as
-subnodes of the emc controller node.
-
-There are two ways of specifying which tables to use:
-
-* The simplest is if there is just one set of tables in the device tree,
- and they will always be used (based on which frequency is used).
- This is the preferred method, especially when firmware can fill in
- this information based on the specific system information and just
- pass it on to the kernel.
-
-* The slightly more complex one is when more than one memory configuration
- might exist on the system. The Tegra20 platform handles this during
- early boot by selecting one out of possible 4 memory settings based
- on a 2-pin "ram code" bootstrap setting on the board. The values of
- these strappings can be read through a register in the SoC, and thus
- used to select which tables to use.
-
-Properties:
-- name : Should be emc-table
-- compatible : Should contain "nvidia,tegra20-emc-table".
-- reg : either an opaque enumerator to tell different tables apart, or
- the valid frequency for which the table should be used (in kHz).
-- clock-frequency : the clock frequency for the EMC at which this
- table should be used (in kHz).
-- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
- for operation at the 'clock-frequency' setting.
- The order and contents of the registers are:
- RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
- WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
- PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
- TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
- ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
- ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
- CFG_CLKTRIM_1, CFG_CLKTRIM_2
-
- emc-table@166000 {
- reg = <166000>;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = < 166000 >;
- nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 >;
- };
-
- emc-table@333000 {
- reg = <333000>;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = < 333000 >;
- nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 >;
- };
--- /dev/null
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+ and chosen using the ramcode board selector. If omitted, only one
+ set of tables can be present and said tables will be used
+ irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+ memory-controller@7000f400 {
+ #address-cells = < 1 >;
+ #size-cells = < 0 >;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f4000 0x200>;
+ }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+ for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+ and they will always be used (based on which frequency is used).
+ This is the preferred method, especially when firmware can fill in
+ this information based on the specific system information and just
+ pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+ might exist on the system. The Tegra20 platform handles this during
+ early boot by selecting one out of possible 4 memory settings based
+ on a 2-pin "ram code" bootstrap setting on the board. The values of
+ these strappings can be read through a register in the SoC, and thus
+ used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+ the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+ table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+ for operation at the 'clock-frequency' setting.
+ The order and contents of the registers are:
+ RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+ WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+ PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+ TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+ ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+ ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+ CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+ emc-table@166000 {
+ reg = <166000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 166000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+
+ emc-table@333000 {
+ reg = <333000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 333000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
- interrupts : Should contain MC General interrupt.
Example:
- mc {
+ memory-controller@0x7000f000 {
compatible = "nvidia,tegra20-mc";
reg = <0x7000f000 0x024
0x7000f03c 0x3c4>;
- interrupts : Should contain MC General interrupt.
Example:
- mc {
+ memory-controller {
compatible = "nvidia,tegra30-mc";
reg = <0x7000f000 0x010
0x7000f03c 0x1b4
--- /dev/null
+* Freescale MXS LCD Interface (LCDIF)
+
+Required properties:
+- compatible: Should be "fsl,<chip>-lcdif". Supported chips include
+ imx23 and imx28.
+- reg: Address and length of the register set for lcdif
+- interrupts: Should contain lcdif interrupts
+
+Optional properties:
+- panel-enable-gpios : Should specify the gpio for panel enable
+
+Examples:
+
+lcdif@80030000 {
+ compatible = "fsl,imx28-lcdif";
+ reg = <0x80030000 2000>;
+ interrupts = <38 86>;
+ panel-enable-gpios = <&gpio3 30 0>;
+};
+++ /dev/null
-NVIDIA Tegra GPIO controller
-
-Required properties:
-- compatible : "nvidia,tegra<chip>-gpio"
-- reg : Physical base address and length of the controller's registers.
-- interrupts : The interrupt outputs from the controller. For Tegra20,
- there should be 7 interrupts specified, and for Tegra30, there should
- be 8 interrupts specified.
-- #gpio-cells : Should be two. The first cell is the pin number and the
- second cell is used to specify optional parameters:
- - bit 0 specifies polarity (0 for normal, 1 for inverted)
-- gpio-controller : Marks the device node as a GPIO controller.
-- #interrupt-cells : Should be 2.
- The first cell is the GPIO number.
- The second cell is used to specify flags:
- bits[3:0] trigger type and level flags:
- 1 = low-to-high edge triggered.
- 2 = high-to-low edge triggered.
- 4 = active high level-sensitive.
- 8 = active low level-sensitive.
- Valid combinations are 1, 2, 3, 4, 8.
-- interrupt-controller : Marks the device node as an interrupt controller.
-
-Example:
-
-gpio: gpio@6000d000 {
- compatible = "nvidia,tegra20-gpio";
- reg = < 0x6000d000 0x1000 >;
- interrupts = < 0 32 0x04
- 0 33 0x04
- 0 34 0x04
- 0 35 0x04
- 0 55 0x04
- 0 87 0x04
- 0 89 0x04 >;
- #gpio-cells = <2>;
- gpio-controller;
- #interrupt-cells = <2>;
- interrupt-controller;
-};
--- /dev/null
+NVIDIA Tegra GPIO controller
+
+Required properties:
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+ there should be 7 interrupts specified, and for Tegra30, there should
+ be 8 interrupts specified.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+ second cell is used to specify optional parameters:
+ - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+ The first cell is the GPIO number.
+ The second cell is used to specify flags:
+ bits[3:0] trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+ Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+ compatible = "nvidia,tegra20-gpio";
+ reg = < 0x6000d000 0x1000 >;
+ interrupts = < 0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04 >;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+};
--- /dev/null
+* Tegra keyboard controller
+
+Required properties:
+- compatible: "nvidia,tegra20-kbc"
+
+Optional properties, in addition to those specified by the shared
+matrix-keyboard bindings:
+
+- linux,fn-keymap: a second keymap, same specification as the
+ matrix-keyboard-controller spec but to be used when the KEY_FN modifier
+ key is pressed.
+- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
+- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
+- nvidia,ghost-filter: enable ghost filtering for this device
+- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
+
+Example:
+
+keyboard: keyboard {
+ compatible = "nvidia,tegra20-kbc";
+ reg = <0x7000e200 0x100>;
+ nvidia,ghost-filter;
+};
+++ /dev/null
-* Tegra keyboard controller
-
-Required properties:
-- compatible: "nvidia,tegra20-kbc"
-
-Optional properties, in addition to those specified by the shared
-matrix-keyboard bindings:
-
-- linux,fn-keymap: a second keymap, same specification as the
- matrix-keyboard-controller spec but to be used when the KEY_FN modifier
- key is pressed.
-- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
-- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
-- nvidia,ghost-filter: enable ghost filtering for this device
-- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
-
-Example:
-
-keyboard: keyboard {
- compatible = "nvidia,tegra20-kbc";
- reg = <0x7000e200 0x100>;
- nvidia,ghost-filter;
-};
--- /dev/null
+* NVIDIA Tegra Secure Digital Host Controller
+
+This controller on Tegra family SoCs provides an interface for MMC, SD,
+and SDIO types of memory cards.
+
+Required properties:
+- compatible : Should be "nvidia,<chip>-sdhci"
+- reg : Should contain SD/MMC registers location and length
+- interrupts : Should contain SD/MMC interrupt
+- bus-width : Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- cd-gpios : Specify GPIOs for card detection
+- wp-gpios : Specify GPIOs for write protection
+- power-gpios : Specify GPIOs for power control
+
+Example:
+
+sdhci@c8000200 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000200 0x200>;
+ interrupts = <47>;
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 155 0>; /* gpio PT3 */
+ bus-width = <8>;
+};
+++ /dev/null
-* NVIDIA Tegra Secure Digital Host Controller
-
-This controller on Tegra family SoCs provides an interface for MMC, SD,
-and SDIO types of memory cards.
-
-Required properties:
-- compatible : Should be "nvidia,<chip>-sdhci"
-- reg : Should contain SD/MMC registers location and length
-- interrupts : Should contain SD/MMC interrupt
-- bus-width : Number of data lines, can be <1>, <4>, or <8>
-
-Optional properties:
-- cd-gpios : Specify GPIOs for card detection
-- wp-gpios : Specify GPIOs for write protection
-- power-gpios : Specify GPIOs for power control
-
-Example:
-
-sdhci@c8000200 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000200 0x200>;
- interrupts = <47>;
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 155 0>; /* gpio PT3 */
- bus-width = <8>;
-};
+++ /dev/null
-NVIDIA compliant embedded controller
-
-Required properties:
-- compatible : should be "nvidia,nvec".
-- reg : the iomem of the i2c slave controller
-- interrupts : the interrupt line of the i2c slave controller
-- clock-frequency : the frequency of the i2c bus
-- gpios : the gpio used for ec request
-- slave-addr: the i2c address of the slave controller
--- /dev/null
+NVIDIA compliant embedded controller
+
+Required properties:
+- compatible : should be "nvidia,nvec".
+- reg : the iomem of the i2c slave controller
+- interrupts : the interrupt line of the i2c slave controller
+- clock-frequency : the frequency of the i2c bus
+- gpios : the gpio used for ec request
+- slave-addr: the i2c address of the slave controller
--- /dev/null
+* STMP3xxx/i.MX28 Time Clock controller
+
+Required properties:
+- compatible: should be one of the following.
+ * "fsl,stmp3xxx-rtc"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: rtc alarm interrupt
+
+Example:
+
+rtc@80056000 {
+ compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc";
+ reg = <0x80056000 2000>;
+ interrupts = <29>;
+};
--- /dev/null
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-alc5632"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the ALC5632's pins:
+
+ ALC5632 pins:
+
+ * SPK_OUTP
+ * SPK_OUTN
+ * HP_OUT_L
+ * HP_OUT_R
+ * AUX_OUT_P
+ * AUX_OUT_N
+ * LINE_IN_L
+ * LINE_IN_R
+ * PHONE_P
+ * PHONE_N
+ * MIC1_P
+ * MIC1_N
+ * MIC2_P
+ * MIC2_N
+ * MICBIAS1
+ * DMICDAT
+
+ Board connectors:
+
+ * Headset Stereophone
+ * Int Spk
+ * Headset Mic
+ * Digital Mic
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller
+- nvidia,audio-codec : The phandle of the ALC5632 audio codec
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-alc5632-paz00",
+ "nvidia,tegra-audio-alc5632";
+
+ nvidia,model = "Compal PAZ00";
+
+ nvidia,audio-routing =
+ "Int Spk", "SPK_OUTP",
+ "Int Spk", "SPK_OUTN",
+ "Headset Mic","MICBIAS1",
+ "MIC1_N", "Headset Mic",
+ "MIC1_P", "Headset Mic",
+ "Headset Stereophone", "HP_OUT_R",
+ "Headset Stereophone", "HP_OUT_L";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&alc5632>;
+};
--- /dev/null
+NVIDIA Tegra audio complex for TrimSlice
+
+Required properties:
+- compatible : "nvidia,tegra-audio-trimslice"
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-trimslice";
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&codec>;
+};
--- /dev/null
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8753"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the WM8753's pins, and the jacks on the board:
+
+ WM8753 pins:
+
+ * LOUT1
+ * LOUT2
+ * ROUT1
+ * ROUT2
+ * MONO1
+ * MONO2
+ * OUT3
+ * OUT4
+ * LINE1
+ * LINE2
+ * RXP
+ * RXN
+ * ACIN
+ * ACOP
+ * MIC1N
+ * MIC1
+ * MIC2N
+ * MIC2
+ * Mic Bias
+
+ Board connectors:
+
+ * Headphone Jack
+ * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8753 audio codec
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-wm8753-whistler",
+ "nvidia,tegra-audio-wm8753"
+ nvidia,model = "tegra-wm8753-harmony";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "LOUT1",
+ "Headphone Jack", "ROUT1";
+
+ nvidia,i2s-controller = <&i2s1>;
+ nvidia,audio-codec = <&wm8753>;
+};
+
--- /dev/null
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8903"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the WM8903's pins, and the jacks on the board:
+
+ WM8903 pins:
+
+ * IN1L
+ * IN1R
+ * IN2L
+ * IN2R
+ * IN3L
+ * IN3R
+ * DMICDAT
+ * HPOUTL
+ * HPOUTR
+ * LINEOUTL
+ * LINEOUTR
+ * LOP
+ * LON
+ * ROP
+ * RON
+ * MICBIAS
+
+ Board connectors:
+
+ * Headphone Jack
+ * Int Spk
+ * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Optional properties:
+- nvidia,spkr-en-gpios : The GPIO that enables the speakers
+- nvidia,hp-mute-gpios : The GPIO that mutes the headphones
+- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
+- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone
+- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-wm8903-harmony",
+ "nvidia,tegra-audio-wm8903"
+ nvidia,model = "tegra-wm8903-harmony";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&codec 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+};
+
--- /dev/null
+NVIDIA Tegra 20 DAS (Digital Audio Switch) controller
+
+Required properties:
+- compatible : "nvidia,tegra20-das"
+- reg : Should contain DAS registers location and length
+
+Example:
+
+das@70000c00 {
+ compatible = "nvidia,tegra20-das";
+ reg = <0x70000c00 0x80>;
+};
--- /dev/null
+NVIDIA Tegra 20 I2S controller
+
+Required properties:
+- compatible : "nvidia,tegra20-i2s"
+- reg : Should contain I2S registers location and length
+- interrupts : Should contain I2S interrupt
+- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
+ request selector for this I2S controller
+
+Example:
+
+i2s@70002800 {
+ compatible = "nvidia,tegra20-i2s";
+ reg = <0x70002800 0x200>;
+ interrupts = < 45 >;
+ nvidia,dma-request-selector = < &apbdma 2 >;
+};
+++ /dev/null
-NVIDIA Tegra audio complex
-
-Required properties:
-- compatible : "nvidia,tegra-audio-alc5632"
-- nvidia,model : The user-visible name of this sound complex.
-- nvidia,audio-routing : A list of the connections between audio components.
- Each entry is a pair of strings, the first being the connection's sink,
- the second being the connection's source. Valid names for sources and
- sinks are the ALC5632's pins:
-
- ALC5632 pins:
-
- * SPK_OUTP
- * SPK_OUTN
- * HP_OUT_L
- * HP_OUT_R
- * AUX_OUT_P
- * AUX_OUT_N
- * LINE_IN_L
- * LINE_IN_R
- * PHONE_P
- * PHONE_N
- * MIC1_P
- * MIC1_N
- * MIC2_P
- * MIC2_N
- * MICBIAS1
- * DMICDAT
-
- Board connectors:
-
- * Headset Stereophone
- * Int Spk
- * Headset Mic
- * Digital Mic
-
-- nvidia,i2s-controller : The phandle of the Tegra I2S controller
-- nvidia,audio-codec : The phandle of the ALC5632 audio codec
-
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-alc5632-paz00",
- "nvidia,tegra-audio-alc5632";
-
- nvidia,model = "Compal PAZ00";
-
- nvidia,audio-routing =
- "Int Spk", "SPK_OUTP",
- "Int Spk", "SPK_OUTN",
- "Headset Mic","MICBIAS1",
- "MIC1_N", "Headset Mic",
- "MIC1_P", "Headset Mic",
- "Headset Stereophone", "HP_OUT_R",
- "Headset Stereophone", "HP_OUT_L";
-
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&alc5632>;
-};
+++ /dev/null
-NVIDIA Tegra audio complex for TrimSlice
-
-Required properties:
-- compatible : "nvidia,tegra-audio-trimslice"
-- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
-- nvidia,audio-codec : The phandle of the WM8903 audio codec
-
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-trimslice";
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&codec>;
-};
+++ /dev/null
-NVIDIA Tegra audio complex
-
-Required properties:
-- compatible : "nvidia,tegra-audio-wm8753"
-- nvidia,model : The user-visible name of this sound complex.
-- nvidia,audio-routing : A list of the connections between audio components.
- Each entry is a pair of strings, the first being the connection's sink,
- the second being the connection's source. Valid names for sources and
- sinks are the WM8753's pins, and the jacks on the board:
-
- WM8753 pins:
-
- * LOUT1
- * LOUT2
- * ROUT1
- * ROUT2
- * MONO1
- * MONO2
- * OUT3
- * OUT4
- * LINE1
- * LINE2
- * RXP
- * RXN
- * ACIN
- * ACOP
- * MIC1N
- * MIC1
- * MIC2N
- * MIC2
- * Mic Bias
-
- Board connectors:
-
- * Headphone Jack
- * Mic Jack
-
-- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
-- nvidia,audio-codec : The phandle of the WM8753 audio codec
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-wm8753-whistler",
- "nvidia,tegra-audio-wm8753"
- nvidia,model = "tegra-wm8753-harmony";
-
- nvidia,audio-routing =
- "Headphone Jack", "LOUT1",
- "Headphone Jack", "ROUT1";
-
- nvidia,i2s-controller = <&i2s1>;
- nvidia,audio-codec = <&wm8753>;
-};
-
+++ /dev/null
-NVIDIA Tegra audio complex
-
-Required properties:
-- compatible : "nvidia,tegra-audio-wm8903"
-- nvidia,model : The user-visible name of this sound complex.
-- nvidia,audio-routing : A list of the connections between audio components.
- Each entry is a pair of strings, the first being the connection's sink,
- the second being the connection's source. Valid names for sources and
- sinks are the WM8903's pins, and the jacks on the board:
-
- WM8903 pins:
-
- * IN1L
- * IN1R
- * IN2L
- * IN2R
- * IN3L
- * IN3R
- * DMICDAT
- * HPOUTL
- * HPOUTR
- * LINEOUTL
- * LINEOUTR
- * LOP
- * LON
- * ROP
- * RON
- * MICBIAS
-
- Board connectors:
-
- * Headphone Jack
- * Int Spk
- * Mic Jack
-
-- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
-- nvidia,audio-codec : The phandle of the WM8903 audio codec
-
-Optional properties:
-- nvidia,spkr-en-gpios : The GPIO that enables the speakers
-- nvidia,hp-mute-gpios : The GPIO that mutes the headphones
-- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
-- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone
-- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone
-
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-wm8903-harmony",
- "nvidia,tegra-audio-wm8903"
- nvidia,model = "tegra-wm8903-harmony";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1L", "Mic Jack";
-
- nvidia,i2s-controller = <&i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&codec 2 0>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
- nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
-};
-
+++ /dev/null
-NVIDIA Tegra 20 DAS (Digital Audio Switch) controller
-
-Required properties:
-- compatible : "nvidia,tegra20-das"
-- reg : Should contain DAS registers location and length
-
-Example:
-
-das@70000c00 {
- compatible = "nvidia,tegra20-das";
- reg = <0x70000c00 0x80>;
-};
+++ /dev/null
-NVIDIA Tegra 20 I2S controller
-
-Required properties:
-- compatible : "nvidia,tegra20-i2s"
-- reg : Should contain I2S registers location and length
-- interrupts : Should contain I2S interrupt
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this I2S controller
-
-Example:
-
-i2s@70002800 {
- compatible = "nvidia,tegra20-i2s";
- reg = <0x70002800 0x200>;
- interrupts = < 45 >;
- nvidia,dma-request-selector = < &apbdma 2 >;
-};
--- /dev/null
+NVIDIA Tegra 2 SPI device
+
+Required properties:
+- compatible : should be "nvidia,tegra20-spi".
+- gpios : should specify GPIOs used for chipselect.
+++ /dev/null
-NVIDIA Tegra 2 SPI device
-
-Required properties:
-- compatible : should be "nvidia,tegra20-spi".
-- gpios : should specify GPIOs used for chipselect.
--- /dev/null
+* Freescale MXS Application UART (AUART)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-auart". The supported SoCs include
+ imx23 and imx28.
+- reg : Address and length of the register set for the device
+- interrupts : Should contain the auart interrupt numbers
+
+Example:
+auart0: serial@8006a000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+ reg = <0x8006a000 0x2000>;
+ interrupts = <112 70 71>;
+};
+
+Note: Each auart port should have an alias correctly numbered in "aliases"
+node.
+
+Example:
+
+aliases {
+ serial0 = &auart0;
+ serial1 = &auart1;
+ serial2 = &auart2;
+ serial3 = &auart3;
+ serial4 = &auart4;
+};
--- /dev/null
+Tegra SOC USB controllers
+
+The device node for a USB controller that is part of a Tegra
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "nvidia,tegra20-ehci" for USB controllers
+ used in host mode.
+ - phy_type : Should be one of "ulpi" or "utmi".
+ - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
+ activated for the bus to be powered.
+
+Required properties for phy_type == ulpi:
+ - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+
+Optional properties:
+ - dr_mode : dual role mode. Indicates the working mode for
+ nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral",
+ or "otg". Default to "host" if not defined for backward compatibility.
+ host means this is a host controller
+ peripheral means it is device controller
+ otg means it can operate as either ("on the go")
+ - nvidia,has-legacy-mode : boolean indicates whether this controller can
+ operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+ registers are accessed through the APB_MISC base address instead of
+ the USB controller. Since this is a legacy issue it probably does not
+ warrant a compatible string of its own.
+++ /dev/null
-Tegra SOC USB controllers
-
-The device node for a USB controller that is part of a Tegra
-SOC is as described in the document "Open Firmware Recommended
-Practice : Universal Serial Bus" with the following modifications
-and additions :
-
-Required properties :
- - compatible : Should be "nvidia,tegra20-ehci" for USB controllers
- used in host mode.
- - phy_type : Should be one of "ulpi" or "utmi".
- - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
- activated for the bus to be powered.
-
-Required properties for phy_type == ulpi:
- - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
-
-Optional properties:
- - dr_mode : dual role mode. Indicates the working mode for
- nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral",
- or "otg". Default to "host" if not defined for backward compatibility.
- host means this is a host controller
- peripheral means it is device controller
- otg means it can operate as either ("on the go")
- - nvidia,has-legacy-mode : boolean indicates whether this controller can
- operate in legacy mode (as APX 2500 / 2600). In legacy mode some
- registers are accessed through the APB_MISC base address instead of
- the USB controller. Since this is a legacy issue it probably does not
- warrant a compatible string of its own.
--- /dev/null
+TI Watchdog Timer (WDT) Controller for OMAP
+
+Required properties:
+compatible:
+- "ti,omap3-wdt" for OMAP3
+- "ti,omap4-wdt" for OMAP4
+- ti,hwmods: Name of the hwmod associated to the WDT
+
+Examples:
+
+wdt2: wdt@4a314000 {
+ compatible = "ti,omap4-wdt", "ti,omap3-wdt";
+ ti,hwmods = "wd_timer2";
+};
select ARM_AMBA
select ARM_VIC
select CPU_ARM926T
- select CLKDEV_LOOKUP
+ select COMMON_CLK
select GENERIC_CLOCKEVENTS
select PINCTRL
select MIGHT_HAVE_CACHE_L2X0
source "arch/arm/mach-ks8695/Kconfig"
-source "arch/arm/mach-lpc32xx/Kconfig"
-
source "arch/arm/mach-msm/Kconfig"
source "arch/arm/mach-mv78xx0/Kconfig"
--- /dev/null
+/*
+ * aks-cdu.dts - Device Tree file for AK signal CDU
+ *
+ * Copyright (C) 2012 AK signal Brno a.s.
+ * 2012 Jiri Prchal <jiri.prchal@aksignal.cz>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+/include/ "ge863-pro3.dtsi"
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs";
+ };
+
+ ahb {
+ apb {
+ usart0: serial@fffb0000 {
+ status = "okay";
+ };
+
+ usart1: serial@fffb4000 {
+ status = "okay";
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 0>;
+ };
+
+ usart2: serial@fffb8000 {
+ status = "okay";
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 0>;
+ };
+
+ usart3: serial@fffd0000 {
+ status = "okay";
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-delay = <0 0>;
+ };
+
+ macb0: ethernet@fffc4000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ usb1: gadget@fffa4000 {
+ atmel,vbus-gpio = <&pioC 15 0>;
+ status = "okay";
+ };
+ };
+
+ usb0: ohci@00500000 {
+ num-ports = <2>;
+ status = "okay";
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ uboot@40000 {
+ label = "uboot";
+ reg = <0x40000 0x80000>;
+ };
+ ubootenv@c0000 {
+ label = "ubootenv";
+ reg = <0xc0000 0x40000>;
+ };
+ kernel@100000 {
+ label = "kernel";
+ reg = <0x100000 0x400000>;
+ };
+ rootfs@500000 {
+ label = "rootfs";
+ reg = <0x500000 0x7b00000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ red {
+ gpios = <&pioC 10 0>;
+ linux,default-trigger = "none";
+ };
+
+ green {
+ gpios = <&pioA 5 1>;
+ linux,default-trigger = "none";
+ default-state = "on";
+ };
+
+ yellow {
+ gpios = <&pioB 20 1>;
+ linux,default-trigger = "none";
+ };
+
+ blue {
+ gpios = <&pioB 21 1>;
+ linux,default-trigger = "none";
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "am33xx.dtsi"
+
+/ {
+ model = "TI AM335x BeagleBone";
+ compatible = "ti,am335x-bone", "ti,am33xx";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "am33xx.dtsi"
+
+/ {
+ model = "TI AM335x EVM";
+ compatible = "ti,am335x-evm", "ti,am33xx";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+};
--- /dev/null
+/*
+ * Device Tree Source for AM33XX SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "ti,am33xx";
+
+ aliases {
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ };
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,cortex-a8";
+ };
+ };
+
+ /*
+ * The soc node represents the soc top level view. It is uses for IPs
+ * that are not memory mapped in the MPU view or for the MPU itself.
+ */
+ soc {
+ compatible = "ti,omap-infra";
+ mpu {
+ compatible = "ti,omap3-mpu";
+ ti,hwmods = "mpu";
+ };
+ };
+
+ /*
+ * XXX: Use a flat representation of the AM33XX interconnect.
+ * The real AM33XX interconnect network is quite complex.Since
+ * that will not bring real advantage to represent that in DT
+ * for the moment, just use a fake OCP bus entry to represent
+ * the whole bus hierarchy.
+ */
+ ocp {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "l3_main";
+
+ intc: interrupt-controller@48200000 {
+ compatible = "ti,omap2-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ ti,intc-size = <128>;
+ reg = <0x48200000 0x1000>;
+ };
+
+ gpio1: gpio@44e07000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio1";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio2: gpio@4804C000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio3: gpio@481AC000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio3";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio4: gpio@481AE000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio4";
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ uart1: serial@44E09000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart1";
+ clock-frequency = <48000000>;
+ };
+
+ uart2: serial@48022000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart2";
+ clock-frequency = <48000000>;
+ };
+
+ uart3: serial@48024000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart3";
+ clock-frequency = <48000000>;
+ };
+
+ uart4: serial@481A6000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart4";
+ clock-frequency = <48000000>;
+ };
+
+ uart5: serial@481A8000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart5";
+ clock-frequency = <48000000>;
+ };
+
+ uart6: serial@481AA000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart6";
+ clock-frequency = <48000000>;
+ };
+
+ i2c1: i2c@44E0B000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c1";
+ };
+
+ i2c2: i2c@4802A000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c2";
+ };
+
+ i2c3: i2c@4819C000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c3";
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap3.dtsi"
+
+/ {
+ model = "TI AM3517 EVM (AM3517/05)";
+ compatible = "ti,am3517-evm", "ti,omap3";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+};
--- /dev/null
+/*
+ * Copyright 2012 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx28.dtsi"
+
+/ {
+ model = "Crystalfontz CFA-10036 Board";
+ compatible = "crystalfontz,cfa10036", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <4>;
+ status = "okay";
+ };
+ };
+
+ apbx@80040000 {
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_b>;
+ status = "okay";
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ gpios = <&gpio3 4 1>;
+ default-state = "on";
+ };
+ };
+};
--- /dev/null
+/*
+ * Embedded Artists LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "lpc32xx.dtsi"
+
+/ {
+ model = "Embedded Artists LPC3250 board based on NXP LPC3250";
+ compatible = "ea,ea3250", "nxp,lpc3250";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x4000000>;
+ };
+
+ ahb {
+ mac: ethernet@31060000 {
+ phy-mode = "rmii";
+ use-iram;
+ };
+
+ /* Here, choose exactly one from: ohci, usbd */
+ ohci@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+
+/*
+ usbd@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+*/
+
+ /* 128MB Flash via SLC NAND controller */
+ slc: flash@20020000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nxp,wdr-clks = <14>;
+ nxp,wwidth = <260000000>;
+ nxp,whold = <104000000>;
+ nxp,wsetup = <200000000>;
+ nxp,rdr-clks = <14>;
+ nxp,rwidth = <34666666>;
+ nxp,rhold = <104000000>;
+ nxp,rsetup = <200000000>;
+ nand-on-flash-bbt;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+ mtd0@00000000 {
+ label = "ea3250-boot";
+ reg = <0x00000000 0x00080000>;
+ read-only;
+ };
+
+ mtd1@00080000 {
+ label = "ea3250-uboot";
+ reg = <0x00080000 0x000c0000>;
+ read-only;
+ };
+
+ mtd2@00140000 {
+ label = "ea3250-kernel";
+ reg = <0x00140000 0x00400000>;
+ };
+
+ mtd3@00540000 {
+ label = "ea3250-rootfs";
+ reg = <0x00540000 0x07ac0000>;
+ };
+ };
+
+ apb {
+ uart5: serial@40090000 {
+ status = "okay";
+ };
+
+ uart3: serial@40080000 {
+ status = "okay";
+ };
+
+ uart6: serial@40098000 {
+ status = "okay";
+ };
+
+ i2c1: i2c@400A0000 {
+ clock-frequency = <100000>;
+
+ eeprom@50 {
+ compatible = "at,24c256";
+ reg = <0x50>;
+ };
+
+ eeprom@57 {
+ compatible = "at,24c64";
+ reg = <0x57>;
+ };
+
+ uda1380: uda1380@18 {
+ compatible = "nxp,uda1380";
+ reg = <0x18>;
+ power-gpio = <&gpio 0x59 0>;
+ reset-gpio = <&gpio 0x51 0>;
+ dac-clk = "wspll";
+ };
+
+ pca9532: pca9532@60 {
+ compatible = "nxp,pca9532";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x60>;
+ };
+ };
+
+ i2c2: i2c@400A8000 {
+ clock-frequency = <100000>;
+ };
+
+ i2cusb: i2c@31020300 {
+ clock-frequency = <100000>;
+
+ isp1301: usb-transceiver@2d {
+ compatible = "nxp,isp1301";
+ reg = <0x2d>;
+ };
+ };
+
+ sd@20098000 {
+ wp-gpios = <&pca9532 5 0>;
+ cd-gpios = <&pca9532 4 0>;
+ cd-inverted;
+ bus-width = <4>;
+ status = "okay";
+ };
+ };
+
+ fab {
+ uart1: serial@40014000 {
+ status = "okay";
+ };
+
+ /* 3-axis accelerometer X,Y,Z (or AD-IN instead of Z) */
+ adc@40048000 {
+ status = "okay";
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+ button@21 {
+ label = "GPIO Key UP";
+ linux,code = <103>;
+ gpios = <&gpio 4 1 0>; /* GPI_P3 1 */
+ };
+ };
+};
--- /dev/null
+/*
+ * evk-pro3.dts - Device Tree file for Telit EVK-PRO3 with Telit GE863-PRO3
+ *
+ * Copyright (C) 2012 Telit,
+ * 2012 Fabio Porcedda <fabio.porcedda@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+/include/ "ge863-pro3.dtsi"
+
+/ {
+ model = "Telit EVK-PRO3 for Telit GE863-PRO3";
+ compatible = "telit,evk-pro3", "atmel,at91sam9260", "atmel,at91sam9";
+
+ ahb {
+ apb {
+ macb0: ethernet@fffc4000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ usb1: gadget@fffa4000 {
+ atmel,vbus-gpio = <&pioC 5 0>;
+ status = "okay";
+ };
+ };
+
+ usb0: ohci@00500000 {
+ num-ports = <2>;
+ status = "okay";
+ };
+ };
+
+ i2c@0 {
+ status = "okay";
+ };
+
+};
\ No newline at end of file
--- /dev/null
+/*
+ * ge863_pro3.dtsi - Device Tree file for Telit GE863-PRO3
+ *
+ * Copyright (C) 2012 Telit,
+ * 2012 Fabio Porcedda <fabio.porcedda@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "at91sam9260.dtsi"
+
+/ {
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock@0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <6000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial@fffff200 {
+ status = "okay";
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+
+ boot@0 {
+ label = "boot";
+ reg = <0x0 0x7c0000>;
+ };
+
+ root@07c0000 {
+ label = "root";
+ reg = <0x7c0000 0x7840000>;
+ };
+ };
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs";
+ };
+};
apb@80000000 {
apbh@80000000 {
+ gpmi-nand@8000c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_pins_fixup>;
+ status = "okay";
+ };
+
ssp0: ssp@80010000 {
compatible = "fsl,imx23-mmc";
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a &mmc0_pins_fixup>;
- bus-width = <8>;
+ pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+ bus-width = <4>;
wp-gpios = <&gpio1 30 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog-gpios@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */
+ 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
+ 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+ };
+
+ lcdif@80030000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a>;
+ panel-enable-gpios = <&gpio1 18 0>;
status = "okay";
};
};
apbx@80040000 {
+ pwm: pwm@80064000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial@8006c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+ };
+
duart: serial@80070000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
};
};
};
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_vddio_sd0: vddio-sd0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 29 0>;
+ };
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
};
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx23.dtsi"
+
+/ {
+ model = "i.MX23 Olinuxino Low Cost Board";
+ compatible = "olimex,imx23-olinuxino", "fsl,imx23";
+
+ memory {
+ reg = <0x40000000 0x04000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx23-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
+ bus-width = <4>;
+ status = "okay";
+ };
+ };
+
+ apbx@80040000 {
+ duart: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+ };
+ };
+};
gpio0 = &gpio0;
gpio1 = &gpio1;
gpio2 = &gpio2;
+ serial0 = &auart0;
+ serial1 = &auart1;
};
cpus {
status = "disabled";
};
- bch@8000a000 {
- reg = <0x8000a000 2000>;
- status = "disabled";
- };
-
- gpmi@8000c000 {
- reg = <0x8000c000 2000>;
+ gpmi-nand@8000c000 {
+ compatible = "fsl,imx23-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x8000c000 2000>, <0x8000a000 2000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <13>, <56>;
+ interrupt-names = "gpmi-dma", "bch";
+ fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
duart_pins_a: duart@0 {
reg = <0>;
- fsl,pinmux-ids = <0x11a2 0x11b2>;
+ fsl,pinmux-ids = <
+ 0x11a2 /* MX23_PAD_PWM0__DUART_RX */
+ 0x11b2 /* MX23_PAD_PWM1__DUART_TX */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ auart0_pins_a: auart0@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */
+ 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */
+ 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */
+ 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */
+ >;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
+ gpmi_pins_a: gpmi-nand@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */
+ 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */
+ 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */
+ 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */
+ 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */
+ 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */
+ 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */
+ 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */
+ 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */
+ 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */
+ 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */
+ 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */
+ 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
+ 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
+ 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
+ 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */
+ 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ gpmi_pins_fixup: gpmi-pins-fixup {
+ fsl,pinmux-ids = <
+ 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
+ 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
+ 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
+ >;
+ fsl,drive-strength = <2>;
+ };
+
+ mmc0_4bit_pins_a: mmc0-4bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
+ 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
+ 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
+ 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
+ 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
+ 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
+ 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ >;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
- fsl,pinmux-ids = <0x2020 0x2030 0x2040
- 0x2050 0x0082 0x0092 0x00a2
- 0x00b2 0x2000 0x2010 0x2060>;
+ fsl,pinmux-ids = <
+ 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
+ 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
+ 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
+ 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
+ 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */
+ 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */
+ 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */
+ 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */
+ 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
+ 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
+ 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ >;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
};
mmc0_pins_fixup: mmc0-pins-fixup {
- fsl,pinmux-ids = <0x2010 0x2060>;
+ fsl,pinmux-ids = <
+ 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
+ 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ >;
+ fsl,pull-up = <0>;
+ };
+
+ pwm2_pins_a: pwm2@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x11c0 /* MX23_PAD_PWM2__PWM2 */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ lcdif_24bit_pins_a: lcdif-24bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */
+ 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */
+ 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */
+ 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */
+ 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */
+ 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */
+ 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */
+ 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */
+ 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */
+ 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */
+ 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */
+ 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */
+ 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */
+ 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */
+ 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */
+ 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */
+ 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */
+ 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */
+ 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */
+ 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */
+ 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */
+ 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */
+ 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */
+ 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */
+ 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */
+ 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */
+ 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */
+ 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
fsl,pull-up = <0>;
};
};
};
lcdif@80030000 {
+ compatible = "fsl,imx23-lcdif";
reg = <0x80030000 2000>;
+ interrupts = <46 45>;
status = "disabled";
};
};
rtc@8005c000 {
+ compatible = "fsl,imx23-rtc", "fsl,stmp3xxx-rtc";
reg = <0x8005c000 2000>;
- status = "disabled";
+ interrupts = <22>;
};
- pwm@80064000 {
+ pwm: pwm@80064000 {
+ compatible = "fsl,imx23-pwm";
reg = <0x80064000 2000>;
+ #pwm-cells = <2>;
+ fsl,pwm-number = <5>;
status = "disabled";
};
};
auart0: serial@8006c000 {
+ compatible = "fsl,imx23-auart";
reg = <0x8006c000 0x2000>;
+ interrupts = <24 25 23>;
status = "disabled";
};
auart1: serial@8006e000 {
+ compatible = "fsl,imx23-auart";
reg = <0x8006e000 0x2000>;
+ interrupts = <59 60 58>;
status = "disabled";
};
apb@80000000 {
apbh@80000000 {
+ gpmi-nand@8000c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+ };
+
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <8>;
wp-gpios = <&gpio2 12 0>;
+ vmmc-supply = <®_vddio_sd0>;
status = "okay";
};
compatible = "fsl,imx28-mmc";
bus-width = <8>;
wp-gpios = <&gpio0 28 0>;
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog-gpios@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
+ 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */
+ 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */
+ 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
+ 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
+ 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+ };
+
+ lcdif@80030000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a>;
+ panel-enable-gpios = <&gpio3 30 0>;
+ status = "okay";
+ };
+
+ can0: can@80032000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ status = "okay";
+ };
+
+ can1: can@80034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
status = "okay";
};
};
};
};
+ pwm: pwm@80064000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+ };
+
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+ };
+
+ auart3: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_pins_a>;
+ status = "okay";
+ };
};
};
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio4 13 0>;
+ phy-reset-duration = <100>;
status = "okay";
};
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
+
+ reg_vddio_sd0: vddio-sd0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vddio-sd0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 28 0>;
+ };
+
+ reg_fec_3v3: fec-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fec-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 15 0>;
+ };
};
sound {
saif-controllers = <&saif0 &saif1>;
audio-codec = <&sgtl5000>;
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ user {
+ label = "Heartbeat";
+ gpios = <&gpio3 5 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
};
gpio4 = &gpio4;
saif0 = &saif0;
saif1 = &saif1;
+ serial0 = &auart0;
+ serial1 = &auart1;
+ serial2 = &auart2;
+ serial3 = &auart3;
+ serial4 = &auart4;
};
cpus {
status = "disabled";
};
- bch@8000a000 {
- reg = <0x8000a000 2000>;
- interrupts = <41>;
- status = "disabled";
- };
-
- gpmi@8000c000 {
- reg = <0x8000c000 2000>;
- interrupts = <42 88>;
+ gpmi-nand@8000c000 {
+ compatible = "fsl,imx28-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x8000c000 2000>, <0x8000a000 2000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <88>, <41>;
+ interrupt-names = "gpmi-dma", "bch";
+ fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
duart_pins_a: duart@0 {
reg = <0>;
- fsl,pinmux-ids = <0x3102 0x3112>;
+ fsl,pinmux-ids = <
+ 0x3102 /* MX28_PAD_PWM0__DUART_RX */
+ 0x3112 /* MX28_PAD_PWM1__DUART_TX */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ duart_pins_b: duart@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
+ 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ gpmi_pins_a: gpmi-nand@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */
+ 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */
+ 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */
+ 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */
+ 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */
+ 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */
+ 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */
+ 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */
+ 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */
+ 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */
+ 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */
+ 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */
+ 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
+ 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
+ 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */
+ 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */
+ 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ gpmi_status_cfg: gpmi-status-cfg {
+ fsl,pinmux-ids = <
+ 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
+ 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
+ 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ >;
+ fsl,drive-strength = <2>;
+ };
+
+ auart0_pins_a: auart0@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
+ 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
+ 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */
+ 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ auart3_pins_a: auart3@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
+ 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
+ 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */
+ 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */
+ >;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
fsl,pull-up = <0>;
mac0_pins_a: mac0@0 {
reg = <0>;
- fsl,pinmux-ids = <0x4000 0x4010 0x4020
- 0x4030 0x4040 0x4060 0x4070
- 0x4080 0x4100>;
+ fsl,pinmux-ids = <
+ 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */
+ 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */
+ 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */
+ 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */
+ 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */
+ 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */
+ 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */
+ 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */
+ 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */
+ >;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
mac1_pins_a: mac1@0 {
reg = <0>;
- fsl,pinmux-ids = <0x40f1 0x4091 0x40a1
- 0x40e1 0x40b1 0x40c1>;
+ fsl,pinmux-ids = <
+ 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */
+ 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */
+ 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */
+ 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */
+ 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */
+ 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */
+ >;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
- fsl,pinmux-ids = <0x2000 0x2010 0x2020
- 0x2030 0x2040 0x2050 0x2060
- 0x2070 0x2080 0x2090 0x20a0>;
+ fsl,pinmux-ids = <
+ 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
+ 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
+ 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
+ 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
+ 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */
+ 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */
+ 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */
+ 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */
+ 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
+ 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
+ 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ >;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ mmc0_4bit_pins_a: mmc0-4bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
+ 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
+ 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
+ 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
+ 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
+ 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
+ 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ >;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
};
mmc0_cd_cfg: mmc0-cd-cfg {
- fsl,pinmux-ids = <0x2090>;
+ fsl,pinmux-ids = <
+ 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
+ >;
fsl,pull-up = <0>;
};
mmc0_sck_cfg: mmc0-sck-cfg {
- fsl,pinmux-ids = <0x20a0>;
+ fsl,pinmux-ids = <
+ 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ >;
fsl,drive-strength = <2>;
fsl,pull-up = <0>;
};
i2c0_pins_a: i2c0@0 {
reg = <0>;
- fsl,pinmux-ids = <0x3180 0x3190>;
+ fsl,pinmux-ids = <
+ 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */
+ 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */
+ >;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
saif0_pins_a: saif0@0 {
reg = <0>;
- fsl,pinmux-ids =
- <0x3140 0x3150 0x3160 0x3170>;
+ fsl,pinmux-ids = <
+ 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */
+ 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
+ 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
+ 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ >;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
saif1_pins_a: saif1@0 {
reg = <0>;
- fsl,pinmux-ids = <0x31a0>;
+ fsl,pinmux-ids = <
+ 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */
+ >;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
fsl,pull-up = <1>;
};
+
+ pwm2_pins_a: pwm2@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x3120 /* MX28_PAD_PWM2__PWM_2 */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ lcdif_24bit_pins_a: lcdif-24bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
+ 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
+ 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
+ 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
+ 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
+ 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
+ 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
+ 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
+ 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
+ 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
+ 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
+ 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
+ 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
+ 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
+ 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
+ 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
+ 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
+ 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */
+ 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */
+ 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */
+ 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */
+ 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */
+ 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */
+ 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+ 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+ 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+ 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ can0_pins_a: can0@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */
+ 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ can1_pins_a: can1@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */
+ 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */
+ >;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
};
digctl@8001c000 {
};
lcdif@80030000 {
+ compatible = "fsl,imx28-lcdif";
reg = <0x80030000 2000>;
interrupts = <38 86>;
status = "disabled";
};
can0: can@80032000 {
+ compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
reg = <0x80032000 2000>;
interrupts = <8>;
status = "disabled";
};
can1: can@80034000 {
+ compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
reg = <0x80034000 2000>;
interrupts = <9>;
status = "disabled";
};
rtc@80056000 {
+ compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc";
reg = <0x80056000 2000>;
- interrupts = <28 29>;
- status = "disabled";
+ interrupts = <29>;
};
i2c0: i2c@80058000 {
status = "disabled";
};
- pwm@80064000 {
+ pwm: pwm@80064000 {
+ compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
reg = <0x80064000 2000>;
+ #pwm-cells = <2>;
+ fsl,pwm-number = <8>;
status = "disabled";
};
};
auart0: serial@8006a000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006a000 0x2000>;
interrupts = <112 70 71>;
status = "disabled";
};
auart1: serial@8006c000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006c000 0x2000>;
interrupts = <113 72 73>;
status = "disabled";
};
auart2: serial@8006e000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006e000 0x2000>;
interrupts = <114 74 75>;
status = "disabled";
};
auart3: serial@80070000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x80070000 0x2000>;
interrupts = <115 76 77>;
status = "disabled";
};
auart4: serial@80072000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x80072000 0x2000>;
interrupts = <116 78 79>;
status = "disabled";
};
soc {
+ gpmi-nand@00112000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand_1>;
+ status = "disabled"; /* gpmi nand conflicts with SD */
+ };
+
aips-bus@02100000 { /* AIPS2 */
ethernet@02188000 {
phy-mode = "rgmii";
interrupt-parent = <&intc>;
ranges;
+ dma-apbh@00110000 {
+ compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x00110000 0x2000>;
+ };
+
+ gpmi-nand@00112000 {
+ compatible = "fsl,imx6q-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x00112000 0x2000>, <0x00114000 0x2000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <0 13 0x04>, <0 15 0x04>;
+ interrupt-names = "gpmi-dma", "bch";
+ fsl,gpmi-dma-channel = <0>;
+ status = "disabled";
+ };
+
timer@00a00600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0x00a00600 0x20>;
};
};
+ gpmi-nand {
+ pinctrl_gpmi_nand_1: gpmi-nand-1 {
+ fsl,pins = <1328 0xb0b1 /* MX6Q_PAD_NANDF_CLE__RAWNAND_CLE */
+ 1336 0xb0b1 /* MX6Q_PAD_NANDF_ALE__RAWNAND_ALE */
+ 1344 0xb0b1 /* MX6Q_PAD_NANDF_WP_B__RAWNAND_RESETN */
+ 1352 0xb000 /* MX6Q_PAD_NANDF_RB0__RAWNAND_READY0 */
+ 1360 0xb0b1 /* MX6Q_PAD_NANDF_CS0__RAWNAND_CE0N */
+ 1365 0xb0b1 /* MX6Q_PAD_NANDF_CS1__RAWNAND_CE1N */
+ 1371 0xb0b1 /* MX6Q_PAD_NANDF_CS2__RAWNAND_CE2N */
+ 1378 0xb0b1 /* MX6Q_PAD_NANDF_CS3__RAWNAND_CE3N */
+ 1387 0xb0b1 /* MX6Q_PAD_SD4_CMD__RAWNAND_RDN */
+ 1393 0xb0b1 /* MX6Q_PAD_SD4_CLK__RAWNAND_WRN */
+ 1397 0xb0b1 /* MX6Q_PAD_NANDF_D0__RAWNAND_D0 */
+ 1405 0xb0b1 /* MX6Q_PAD_NANDF_D1__RAWNAND_D1 */
+ 1413 0xb0b1 /* MX6Q_PAD_NANDF_D2__RAWNAND_D2 */
+ 1421 0xb0b1 /* MX6Q_PAD_NANDF_D3__RAWNAND_D3 */
+ 1429 0xb0b1 /* MX6Q_PAD_NANDF_D4__RAWNAND_D4 */
+ 1437 0xb0b1 /* MX6Q_PAD_NANDF_D5__RAWNAND_D5 */
+ 1445 0xb0b1 /* MX6Q_PAD_NANDF_D6__RAWNAND_D6 */
+ 1453 0xb0b1 /* MX6Q_PAD_NANDF_D7__RAWNAND_D7 */
+ 1463 0x00b1>; /* MX6Q_PAD_SD4_DAT0__RAWNAND_DQS */
+ };
+ };
+
i2c1 {
pinctrl_i2c1_1: i2c1grp-1 {
fsl,pins = <137 0x4001b8b1 /* MX6Q_PAD_EIM_D21__I2C1_SCL */
slc: flash@20020000 {
compatible = "nxp,lpc3220-slc";
reg = <0x20020000 0x1000>;
- status = "disable";
+ status = "disabled";
};
- mlc: flash@200B0000 {
+ mlc: flash@200a8000 {
compatible = "nxp,lpc3220-mlc";
- reg = <0x200B0000 0x1000>;
- status = "disable";
+ reg = <0x200a8000 0x11000>;
+ interrupts = <11 0>;
+ status = "disabled";
};
dma@31000000 {
compatible = "nxp,ohci-nxp", "usb-ohci";
reg = <0x31020000 0x300>;
interrupts = <0x3b 0>;
- status = "disable";
+ status = "disabled";
};
usbd@31020000 {
compatible = "nxp,lpc3220-udc";
reg = <0x31020000 0x300>;
interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>;
- status = "disable";
+ status = "disabled";
};
clcd@31040000 {
compatible = "arm,pl110", "arm,primecell";
reg = <0x31040000 0x1000>;
interrupts = <0x0e 0>;
- status = "disable";
+ status = "disabled";
};
mac: ethernet@31060000 {
};
sd@20098000 {
- compatible = "arm,pl180", "arm,primecell";
+ compatible = "arm,pl18x", "arm,primecell";
reg = <0x20098000 0x1000>;
interrupts = <0x0f 0>, <0x0d 0>;
+ status = "disabled";
};
i2s1: i2s@2009C000 {
reg = <0x2009C000 0x1000>;
};
+ /* UART5 first since it is the default console, ttyS0 */
+ uart5: serial@40090000 {
+ /* actually, ns16550a w/ 64 byte fifos! */
+ compatible = "nxp,lpc3220-uart";
+ reg = <0x40090000 0x1000>;
+ interrupts = <9 0>;
+ clock-frequency = <13000000>;
+ reg-shift = <2>;
+ status = "disabled";
+ };
+
uart3: serial@40080000 {
- compatible = "nxp,serial";
+ compatible = "nxp,lpc3220-uart";
reg = <0x40080000 0x1000>;
+ interrupts = <7 0>;
+ clock-frequency = <13000000>;
+ reg-shift = <2>;
+ status = "disabled";
};
uart4: serial@40088000 {
- compatible = "nxp,serial";
+ compatible = "nxp,lpc3220-uart";
reg = <0x40088000 0x1000>;
- };
-
- uart5: serial@40090000 {
- compatible = "nxp,serial";
- reg = <0x40090000 0x1000>;
+ interrupts = <8 0>;
+ clock-frequency = <13000000>;
+ reg-shift = <2>;
+ status = "disabled";
};
uart6: serial@40098000 {
- compatible = "nxp,serial";
+ compatible = "nxp,lpc3220-uart";
reg = <0x40098000 0x1000>;
+ interrupts = <10 0>;
+ clock-frequency = <13000000>;
+ reg-shift = <2>;
+ status = "disabled";
};
i2c1: i2c@400A0000 {
};
uart1: serial@40014000 {
- compatible = "nxp,serial";
+ compatible = "nxp,lpc3220-hsuart";
reg = <0x40014000 0x1000>;
+ interrupts = <26 0>;
+ status = "disabled";
};
uart2: serial@40018000 {
- compatible = "nxp,serial";
+ compatible = "nxp,lpc3220-hsuart";
reg = <0x40018000 0x1000>;
+ interrupts = <25 0>;
+ status = "disabled";
};
- uart7: serial@4001C000 {
- compatible = "nxp,serial";
- reg = <0x4001C000 0x1000>;
+ uart7: serial@4001c000 {
+ compatible = "nxp,lpc3220-hsuart";
+ reg = <0x4001c000 0x1000>;
+ interrupts = <24 0>;
+ status = "disabled";
};
rtc@40024000 {
compatible = "nxp,lpc3220-adc";
reg = <0x40048000 0x1000>;
interrupts = <0x27 0>;
- status = "disable";
+ status = "disabled";
};
tsc@40048000 {
compatible = "nxp,lpc3220-tsc";
reg = <0x40048000 0x1000>;
interrupts = <0x27 0>;
- status = "disable";
+ status = "disabled";
};
key@40050000 {
compatible = "nxp,lpc3220-key";
reg = <0x40050000 0x1000>;
+ interrupts = <54 0>;
+ status = "disabled";
};
};
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap2.dtsi"
+
+/ {
+ model = "TI OMAP2420 H4 board";
+ compatible = "ti,omap2420-h4", "ti,omap2420", "ti,omap2";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x84000000>; /* 64 MB */
+ };
+};
reg = <0x80000000 0x10000000>; /* 256 MB */
};
};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ };
+};
+
+/include/ "twl4030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ /*
+ * TVP5146 Video decoder-in for analog input support.
+ */
+ tvp5146@5c {
+ compatible = "ti,tvp5146m2";
+ reg = <0x5c>;
+ };
+};
compatible = "ti,omap3-hsmmc";
ti,hwmods = "mmc3";
};
+
+ wdt2: wdt@48314000 {
+ compatible = "ti,omap3-wdt";
+ ti,hwmods = "wd_timer2";
+ };
};
};
linux,default-trigger = "mmc0";
};
};
+
+ sound: sound {
+ compatible = "ti,abe-twl6040";
+ ti,model = "PandaBoard";
+
+ ti,mclk-freq = <38400000>;
+
+ ti,mcpdm = <&mcpdm>;
+
+ ti,twl6040 = <&twl6040>;
+
+ /* Audio routing */
+ ti,audio-routing =
+ "Headset Stereophone", "HSOL",
+ "Headset Stereophone", "HSOR",
+ "Ext Spk", "HFL",
+ "Ext Spk", "HFR",
+ "Line Out", "AUXL",
+ "Line Out", "AUXR",
+ "HSMIC", "Headset Mic",
+ "Headset Mic", "Headset Mic Bias",
+ "AFML", "Line In",
+ "AFMR", "Line In";
+ };
};
&i2c1 {
interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
interrupt-parent = <&gic>;
};
+
+ twl6040: twl@4b {
+ compatible = "ti,twl6040";
+ reg = <0x4b>;
+ /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
+ interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */
+ interrupt-parent = <&gic>;
+ ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */
+
+ vio-supply = <&v1v8>;
+ v2v1-supply = <&v2v1>;
+ enable-active-high;
+ };
};
/include/ "twl6030.dtsi"
--- /dev/null
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/include/ "omap4-panda.dts"
+
+/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */
+&sound {
+ ti,model = "PandaBoardES";
+
+ /* Audio routing */
+ ti,audio-routing =
+ "Headset Stereophone", "HSOL",
+ "Headset Stereophone", "HSOR",
+ "Ext Spk", "HFL",
+ "Ext Spk", "HFR",
+ "Line Out", "AUXL",
+ "Line Out", "AUXR",
+ "AFML", "Line In",
+ "AFMR", "Line In";
+};
regulator-boot-on;
};
+ vbat: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "VBAT";
+ regulator-min-microvolt = <3750000>;
+ regulator-max-microvolt = <3750000>;
+ regulator-boot-on;
+ };
+
leds {
compatible = "gpio-leds";
debug0 {
gpios = <&gpio5 11 0>; /* 139 */
};
};
+
+ sound {
+ compatible = "ti,abe-twl6040";
+ ti,model = "SDP4430";
+
+ ti,jack-detection = <1>;
+ ti,mclk-freq = <38400000>;
+
+ ti,mcpdm = <&mcpdm>;
+ ti,dmic = <&dmic>;
+
+ ti,twl6040 = <&twl6040>;
+
+ /* Audio routing */
+ ti,audio-routing =
+ "Headset Stereophone", "HSOL",
+ "Headset Stereophone", "HSOR",
+ "Earphone Spk", "EP",
+ "Ext Spk", "HFL",
+ "Ext Spk", "HFR",
+ "Line Out", "AUXL",
+ "Line Out", "AUXR",
+ "Vibrator", "VIBRAL",
+ "Vibrator", "VIBRAR",
+ "HSMIC", "Headset Mic",
+ "Headset Mic", "Headset Mic Bias",
+ "MAINMIC", "Main Handset Mic",
+ "Main Handset Mic", "Main Mic Bias",
+ "SUBMIC", "Sub Handset Mic",
+ "Sub Handset Mic", "Main Mic Bias",
+ "AFML", "Line In",
+ "AFMR", "Line In",
+ "DMic", "Digital Mic",
+ "Digital Mic", "Digital Mic1 Bias";
+ };
};
&i2c1 {
interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
interrupt-parent = <&gic>;
};
+
+ twl6040: twl@4b {
+ compatible = "ti,twl6040";
+ reg = <0x4b>;
+ /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
+ interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */
+ interrupt-parent = <&gic>;
+ ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */
+
+ vio-supply = <&v1v8>;
+ v2v1-supply = <&v2v1>;
+ enable-active-high;
+
+ /* regulators for vibra motor */
+ vddvibl-supply = <&vbat>;
+ vddvibr-supply = <&vbat>;
+
+ vibra {
+ /* Vibra driver, motor resistance parameters */
+ ti,vibldrv-res = <8>;
+ ti,vibrdrv-res = <3>;
+ ti,viblmotor-res = <10>;
+ ti,vibrmotor-res = <10>;
+ };
+ };
};
/include/ "twl6030.dtsi"
--- /dev/null
+/*
+ * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap4.dtsi"
+
+/ {
+ model = "Variscite OMAP4 SOM";
+ compatible = "var,omap4-var_som", "ti,omap4430", "ti,omap4";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ vdd_eth: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_ETH";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+ interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
+ interrupt-parent = <&gic>;
+ };
+};
+
+/include/ "twl6030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+
+ /*
+ * Temperature Sensor
+ * http://www.ti.com/lit/ds/symlink/tmp105.pdf
+ */
+ tmp105@49 {
+ compatible = "ti,tmp105";
+ reg = <0x49>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+};
+
+&mcspi1 {
+ eth@0 {
+ compatible = "ks8851";
+ spi-max-frequency = <24000000>;
+ reg = <0>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <11>; /* gpio line 171 */
+ vdd-supply = <&vdd_eth>;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc>;
+ ti,bus-width = <8>;
+ ti,non-removable;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mmc4 {
+ status = "disabled";
+};
+
+&mmc5 {
+ ti,bus-width = <4>;
+};
ti,hwmods = "mmc5";
ti,needs-special-reset;
};
+
+ wdt2: wdt@4a314000 {
+ compatible = "ti,omap4-wdt", "ti,omap3-wdt";
+ ti,hwmods = "wd_timer2";
+ };
+
+ mcpdm: mcpdm@40132000 {
+ compatible = "ti,omap4-mcpdm";
+ reg = <0x40132000 0x7f>, /* MPU private access */
+ <0x49032000 0x7f>; /* L3 Interconnect */
+ interrupts = <0 112 0x4>;
+ interrupt-parent = <&gic>;
+ ti,hwmods = "mcpdm";
+ };
+
+ dmic: dmic@4012e000 {
+ compatible = "ti,omap4-dmic";
+ reg = <0x4012e000 0x7f>, /* MPU private access */
+ <0x4902e000 0x7f>; /* L3 Interconnect */
+ interrupts = <0 114 0x4>;
+ interrupt-parent = <&gic>;
+ ti,hwmods = "dmic";
+ };
};
};
#address-cells = <1>;
#size-cells = <1>;
+ nxp,wdr-clks = <14>;
+ nxp,wwidth = <40000000>;
+ nxp,whold = <100000000>;
+ nxp,wsetup = <100000000>;
+ nxp,rdr-clks = <14>;
+ nxp,rwidth = <40000000>;
+ nxp,rhold = <66666666>;
+ nxp,rsetup = <100000000>;
+ nand-on-flash-bbt;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
mtd0@00000000 {
label = "phy3250-boot";
reg = <0x00000000 0x00064000>;
};
apb {
+ uart5: serial@40090000 {
+ status = "okay";
+ };
+
+ uart3: serial@40080000 {
+ status = "okay";
+ };
+
i2c1: i2c@400A0000 {
clock-frequency = <100000>;
};
ssp0: ssp@20084000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pl022,num-chipselects = <1>;
+ cs-gpios = <&gpio 3 5 0>;
+
eeprom: at25@0 {
+ pl022,hierarchy = <0>;
+ pl022,interface = <0>;
+ pl022,slave-tx-disable = <0>;
+ pl022,com-mode = <0>;
+ pl022,rx-level-trig = <1>;
+ pl022,tx-level-trig = <1>;
+ pl022,ctrl-len = <11>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+
+ at25,byte-len = <0x8000>;
+ at25,addr-mode = <2>;
+ at25,page-size = <64>;
+
compatible = "atmel,at25";
+ reg = <0>;
+ spi-max-frequency = <5000000>;
};
};
+
+ sd@20098000 {
+ wp-gpios = <&gpio 3 0 0>;
+ cd-gpios = <&gpio 3 1 0>;
+ cd-inverted;
+ bus-width = <4>;
+ status = "okay";
+ };
};
fab {
+ uart2: serial@40018000 {
+ status = "okay";
+ };
+
tsc@40048000 {
status = "okay";
};
+
+ key@40050000 {
+ status = "okay";
+ keypad,num-rows = <1>;
+ keypad,num-columns = <1>;
+ nxp,debounce-delay-ms = <3>;
+ nxp,scan-delay-ms = <34>;
+ linux,keymap = <0x00000002>;
+ };
};
};
+++ /dev/null
-/dts-v1/;
-
-/include/ "tegra30.dtsi"
-
-/ {
- model = "NVIDIA Tegra30 Cardhu evaluation board";
- compatible = "nvidia,cardhu", "nvidia,tegra30";
-
- memory {
- reg = <0x80000000 0x40000000>;
- };
-
- pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinmux {
- sdmmc1_clk_pz0 {
- nvidia,pins = "sdmmc1_clk_pz0";
- nvidia,function = "sdmmc1";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- sdmmc1_cmd_pz1 {
- nvidia,pins = "sdmmc1_cmd_pz1",
- "sdmmc1_dat0_py7",
- "sdmmc1_dat1_py6",
- "sdmmc1_dat2_py5",
- "sdmmc1_dat3_py4";
- nvidia,function = "sdmmc1";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- sdmmc4_clk_pcc4 {
- nvidia,pins = "sdmmc4_clk_pcc4",
- "sdmmc4_rst_n_pcc3";
- nvidia,function = "sdmmc4";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- sdmmc4_dat0_paa0 {
- nvidia,pins = "sdmmc4_dat0_paa0",
- "sdmmc4_dat1_paa1",
- "sdmmc4_dat2_paa2",
- "sdmmc4_dat3_paa3",
- "sdmmc4_dat4_paa4",
- "sdmmc4_dat5_paa5",
- "sdmmc4_dat6_paa6",
- "sdmmc4_dat7_paa7";
- nvidia,function = "sdmmc4";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- dap2_fs_pa2 {
- nvidia,pins = "dap2_fs_pa2",
- "dap2_sclk_pa3",
- "dap2_din_pa4",
- "dap2_dout_pa5";
- nvidia,function = "i2s1";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- };
- };
-
- serial@70006000 {
- status = "okay";
- clock-frequency = <408000000>;
- };
-
- i2c@7000c000 {
- status = "okay";
- clock-frequency = <100000>;
- };
-
- i2c@7000c400 {
- status = "okay";
- clock-frequency = <100000>;
- };
-
- i2c@7000c500 {
- status = "okay";
- clock-frequency = <100000>;
-
- /* ALS and Proximity sensor */
- isl29028@44 {
- compatible = "isil,isl29028";
- reg = <0x44>;
- interrupt-parent = <&gpio>;
- interrupts = <88 0x04>; /*gpio PL0 */
- };
- };
-
- i2c@7000c700 {
- status = "okay";
- clock-frequency = <100000>;
- };
-
- i2c@7000d000 {
- status = "okay";
- clock-frequency = <100000>;
-
- wm8903: wm8903@1a {
- compatible = "wlf,wm8903";
- reg = <0x1a>;
- interrupt-parent = <&gpio>;
- interrupts = <179 0x04>; /* gpio PW3 */
-
- gpio-controller;
- #gpio-cells = <2>;
-
- micdet-cfg = <0>;
- micdet-delay = <100>;
- gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
- };
-
- tps62361 {
- compatible = "ti,tps62361";
- reg = <0x60>;
-
- regulator-name = "tps62361-vout";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1500000>;
- regulator-boot-on;
- regulator-always-on;
- ti,vsel0-state-high;
- ti,vsel1-state-high;
- };
- };
-
- ahub {
- i2s@70080400 {
- status = "okay";
- };
- };
-
- sdhci@78000000 {
- status = "okay";
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 155 0>; /* gpio PT3 */
- power-gpios = <&gpio 31 0>; /* gpio PD7 */
- bus-width = <4>;
- };
-
- sdhci@78000600 {
- status = "okay";
- support-8bit;
- bus-width = <8>;
- };
-
- sound {
- compatible = "nvidia,tegra-audio-wm8903-cardhu",
- "nvidia,tegra-audio-wm8903";
- nvidia,model = "NVIDIA Tegra Cardhu";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1L", "Mic Jack";
-
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&wm8903 2 0>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- };
-};
+++ /dev/null
-/dts-v1/;
-
-/include/ "tegra20.dtsi"
-
-/ {
- model = "NVIDIA Tegra2 Harmony evaluation board";
- compatible = "nvidia,harmony", "nvidia,tegra20";
-
- memory {
- reg = <0x00000000 0x40000000>;
- };
-
- pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinmux {
- ata {
- nvidia,pins = "ata";
- nvidia,function = "ide";
- };
- atb {
- nvidia,pins = "atb", "gma", "gme";
- nvidia,function = "sdio4";
- };
- atc {
- nvidia,pins = "atc";
- nvidia,function = "nand";
- };
- atd {
- nvidia,pins = "atd", "ate", "gmb", "gmd", "gpu",
- "spia", "spib", "spic";
- nvidia,function = "gmi";
- };
- cdev1 {
- nvidia,pins = "cdev1";
- nvidia,function = "plla_out";
- };
- cdev2 {
- nvidia,pins = "cdev2";
- nvidia,function = "pllp_out4";
- };
- crtp {
- nvidia,pins = "crtp";
- nvidia,function = "crt";
- };
- csus {
- nvidia,pins = "csus";
- nvidia,function = "vi_sensor_clk";
- };
- dap1 {
- nvidia,pins = "dap1";
- nvidia,function = "dap1";
- };
- dap2 {
- nvidia,pins = "dap2";
- nvidia,function = "dap2";
- };
- dap3 {
- nvidia,pins = "dap3";
- nvidia,function = "dap3";
- };
- dap4 {
- nvidia,pins = "dap4";
- nvidia,function = "dap4";
- };
- ddc {
- nvidia,pins = "ddc";
- nvidia,function = "i2c2";
- };
- dta {
- nvidia,pins = "dta", "dtd";
- nvidia,function = "sdio2";
- };
- dtb {
- nvidia,pins = "dtb", "dtc", "dte";
- nvidia,function = "rsvd1";
- };
- dtf {
- nvidia,pins = "dtf";
- nvidia,function = "i2c3";
- };
- gmc {
- nvidia,pins = "gmc";
- nvidia,function = "uartd";
- };
- gpu7 {
- nvidia,pins = "gpu7";
- nvidia,function = "rtck";
- };
- gpv {
- nvidia,pins = "gpv", "slxa", "slxk";
- nvidia,function = "pcie";
- };
- hdint {
- nvidia,pins = "hdint", "pta";
- nvidia,function = "hdmi";
- };
- i2cp {
- nvidia,pins = "i2cp";
- nvidia,function = "i2cp";
- };
- irrx {
- nvidia,pins = "irrx", "irtx";
- nvidia,function = "uarta";
- };
- kbca {
- nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
- "kbce", "kbcf";
- nvidia,function = "kbc";
- };
- lcsn {
- nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
- "ld3", "ld4", "ld5", "ld6", "ld7",
- "ld8", "ld9", "ld10", "ld11", "ld12",
- "ld13", "ld14", "ld15", "ld16", "ld17",
- "ldc", "ldi", "lhp0", "lhp1", "lhp2",
- "lhs", "lm0", "lm1", "lpp", "lpw0",
- "lpw1", "lpw2", "lsc0", "lsc1", "lsck",
- "lsda", "lsdi", "lspi", "lvp0", "lvp1",
- "lvs";
- nvidia,function = "displaya";
- };
- owc {
- nvidia,pins = "owc", "spdi", "spdo", "uac";
- nvidia,function = "rsvd2";
- };
- pmc {
- nvidia,pins = "pmc";
- nvidia,function = "pwr_on";
- };
- rm {
- nvidia,pins = "rm";
- nvidia,function = "i2c1";
- };
- sdb {
- nvidia,pins = "sdb", "sdc", "sdd";
- nvidia,function = "pwm";
- };
- sdio1 {
- nvidia,pins = "sdio1";
- nvidia,function = "sdio1";
- };
- slxc {
- nvidia,pins = "slxc", "slxd";
- nvidia,function = "spdif";
- };
- spid {
- nvidia,pins = "spid", "spie", "spif";
- nvidia,function = "spi1";
- };
- spig {
- nvidia,pins = "spig", "spih";
- nvidia,function = "spi2_alt";
- };
- uaa {
- nvidia,pins = "uaa", "uab", "uda";
- nvidia,function = "ulpi";
- };
- uad {
- nvidia,pins = "uad";
- nvidia,function = "irda";
- };
- uca {
- nvidia,pins = "uca", "ucb";
- nvidia,function = "uartc";
- };
- conf_ata {
- nvidia,pins = "ata", "atb", "atc", "atd", "ate",
- "cdev1", "cdev2", "dap1", "dtb", "gma",
- "gmb", "gmc", "gmd", "gme", "gpu7",
- "gpv", "i2cp", "pta", "rm", "slxa",
- "slxk", "spia", "spib", "uac";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- conf_ck32 {
- nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
- "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
- nvidia,pull = <0>;
- };
- conf_csus {
- nvidia,pins = "csus", "spid", "spif";
- nvidia,pull = <1>;
- nvidia,tristate = <1>;
- };
- conf_crtp {
- nvidia,pins = "crtp", "dap2", "dap3", "dap4",
- "dtc", "dte", "dtf", "gpu", "sdio1",
- "slxc", "slxd", "spdi", "spdo", "spig",
- "uda";
- nvidia,pull = <0>;
- nvidia,tristate = <1>;
- };
- conf_ddc {
- nvidia,pins = "ddc", "dta", "dtd", "kbca",
- "kbcb", "kbcc", "kbcd", "kbce", "kbcf",
- "sdc";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- conf_hdint {
- nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
- "lpw1", "lsc1", "lsck", "lsda", "lsdi",
- "lvp0", "owc", "sdb";
- nvidia,tristate = <1>;
- };
- conf_irrx {
- nvidia,pins = "irrx", "irtx", "sdd", "spic",
- "spie", "spih", "uaa", "uab", "uad",
- "uca", "ucb";
- nvidia,pull = <2>;
- nvidia,tristate = <1>;
- };
- conf_lc {
- nvidia,pins = "lc", "ls";
- nvidia,pull = <2>;
- };
- conf_ld0 {
- nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
- "ld5", "ld6", "ld7", "ld8", "ld9",
- "ld10", "ld11", "ld12", "ld13", "ld14",
- "ld15", "ld16", "ld17", "ldi", "lhp0",
- "lhp1", "lhp2", "lhs", "lm0", "lpp",
- "lpw0", "lpw2", "lsc0", "lspi", "lvp1",
- "lvs", "pmc";
- nvidia,tristate = <0>;
- };
- conf_ld17_0 {
- nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
- "ld23_22";
- nvidia,pull = <1>;
- };
- };
- };
-
- i2s@70002800 {
- status = "okay";
- };
-
- serial@70006300 {
- status = "okay";
- clock-frequency = <216000000>;
- };
-
- i2c@7000c000 {
- status = "okay";
- clock-frequency = <400000>;
-
- wm8903: wm8903@1a {
- compatible = "wlf,wm8903";
- reg = <0x1a>;
- interrupt-parent = <&gpio>;
- interrupts = <187 0x04>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- micdet-cfg = <0>;
- micdet-delay = <100>;
- gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
- };
- };
-
- i2c@7000c400 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000c500 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000d000 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- pmc {
- nvidia,invert-interrupt;
- };
-
- usb@c5000000 {
- status = "okay";
- };
-
- usb@c5004000 {
- status = "okay";
- nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
- };
-
- usb@c5008000 {
- status = "okay";
- };
-
- sdhci@c8000200 {
- status = "okay";
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 155 0>; /* gpio PT3 */
- bus-width = <4>;
- };
-
- sdhci@c8000600 {
- status = "okay";
- cd-gpios = <&gpio 58 0>; /* gpio PH2 */
- wp-gpios = <&gpio 59 0>; /* gpio PH3 */
- power-gpios = <&gpio 70 0>; /* gpio PI6 */
- support-8bit;
- bus-width = <8>;
- };
-
- sound {
- compatible = "nvidia,tegra-audio-wm8903-harmony",
- "nvidia,tegra-audio-wm8903";
- nvidia,model = "NVIDIA Tegra Harmony";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1L", "Mic Jack";
-
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&wm8903 2 0>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
- nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
- };
-};
+++ /dev/null
-/dts-v1/;
-
-/include/ "tegra20.dtsi"
-
-/ {
- model = "Toshiba AC100 / Dynabook AZ";
- compatible = "compal,paz00", "nvidia,tegra20";
-
- memory {
- reg = <0x00000000 0x20000000>;
- };
-
- pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinmux {
- ata {
- nvidia,pins = "ata", "atc", "atd", "ate",
- "dap2", "gmb", "gmc", "gmd", "spia",
- "spib", "spic", "spid", "spie";
- nvidia,function = "gmi";
- };
- atb {
- nvidia,pins = "atb", "gma", "gme";
- nvidia,function = "sdio4";
- };
- cdev1 {
- nvidia,pins = "cdev1";
- nvidia,function = "plla_out";
- };
- cdev2 {
- nvidia,pins = "cdev2";
- nvidia,function = "pllp_out4";
- };
- crtp {
- nvidia,pins = "crtp";
- nvidia,function = "crt";
- };
- csus {
- nvidia,pins = "csus";
- nvidia,function = "pllc_out1";
- };
- dap1 {
- nvidia,pins = "dap1";
- nvidia,function = "dap1";
- };
- dap3 {
- nvidia,pins = "dap3";
- nvidia,function = "dap3";
- };
- dap4 {
- nvidia,pins = "dap4";
- nvidia,function = "dap4";
- };
- ddc {
- nvidia,pins = "ddc";
- nvidia,function = "i2c2";
- };
- dta {
- nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
- nvidia,function = "rsvd1";
- };
- dtf {
- nvidia,pins = "dtf";
- nvidia,function = "i2c3";
- };
- gpu {
- nvidia,pins = "gpu", "sdb", "sdd";
- nvidia,function = "pwm";
- };
- gpu7 {
- nvidia,pins = "gpu7";
- nvidia,function = "rtck";
- };
- gpv {
- nvidia,pins = "gpv", "slxa", "slxk";
- nvidia,function = "pcie";
- };
- hdint {
- nvidia,pins = "hdint", "pta";
- nvidia,function = "hdmi";
- };
- i2cp {
- nvidia,pins = "i2cp";
- nvidia,function = "i2cp";
- };
- irrx {
- nvidia,pins = "irrx", "irtx";
- nvidia,function = "uarta";
- };
- kbca {
- nvidia,pins = "kbca", "kbcc", "kbce", "kbcf";
- nvidia,function = "kbc";
- };
- kbcb {
- nvidia,pins = "kbcb", "kbcd";
- nvidia,function = "sdio2";
- };
- lcsn {
- nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
- "ld3", "ld4", "ld5", "ld6", "ld7",
- "ld8", "ld9", "ld10", "ld11", "ld12",
- "ld13", "ld14", "ld15", "ld16", "ld17",
- "ldc", "ldi", "lhp0", "lhp1", "lhp2",
- "lhs", "lm0", "lm1", "lpp", "lpw0",
- "lpw1", "lpw2", "lsc0", "lsc1", "lsck",
- "lsda", "lsdi", "lspi", "lvp0", "lvp1",
- "lvs";
- nvidia,function = "displaya";
- };
- owc {
- nvidia,pins = "owc";
- nvidia,function = "owr";
- };
- pmc {
- nvidia,pins = "pmc";
- nvidia,function = "pwr_on";
- };
- rm {
- nvidia,pins = "rm";
- nvidia,function = "i2c1";
- };
- sdc {
- nvidia,pins = "sdc";
- nvidia,function = "twc";
- };
- sdio1 {
- nvidia,pins = "sdio1";
- nvidia,function = "sdio1";
- };
- slxc {
- nvidia,pins = "slxc", "slxd";
- nvidia,function = "spi4";
- };
- spdi {
- nvidia,pins = "spdi", "spdo";
- nvidia,function = "rsvd2";
- };
- spif {
- nvidia,pins = "spif", "uac";
- nvidia,function = "rsvd4";
- };
- spig {
- nvidia,pins = "spig", "spih";
- nvidia,function = "spi2_alt";
- };
- uaa {
- nvidia,pins = "uaa", "uab", "uda";
- nvidia,function = "ulpi";
- };
- uad {
- nvidia,pins = "uad";
- nvidia,function = "spdif";
- };
- uca {
- nvidia,pins = "uca", "ucb";
- nvidia,function = "uartc";
- };
- conf_ata {
- nvidia,pins = "ata", "atb", "atc", "atd", "ate",
- "cdev1", "cdev2", "dap1", "dap2", "dtf",
- "gma", "gmb", "gmc", "gmd", "gme",
- "gpu", "gpu7", "gpv", "i2cp", "pta",
- "rm", "sdio1", "slxk", "spdo", "uac",
- "uda";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- conf_ck32 {
- nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
- "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
- nvidia,pull = <0>;
- };
- conf_crtp {
- nvidia,pins = "crtp", "dap3", "dap4", "dtb",
- "dtc", "dte", "slxa", "slxc", "slxd",
- "spdi";
- nvidia,pull = <0>;
- nvidia,tristate = <1>;
- };
- conf_csus {
- nvidia,pins = "csus", "spia", "spib", "spid",
- "spif";
- nvidia,pull = <1>;
- nvidia,tristate = <1>;
- };
- conf_ddc {
- nvidia,pins = "ddc", "irrx", "irtx", "kbca",
- "kbcb", "kbcc", "kbcd", "kbce", "kbcf",
- "spic", "spig", "uaa", "uab";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- conf_dta {
- nvidia,pins = "dta", "dtd", "owc", "sdc", "sdd",
- "spie", "spih", "uad", "uca", "ucb";
- nvidia,pull = <2>;
- nvidia,tristate = <1>;
- };
- conf_hdint {
- nvidia,pins = "hdint", "ld0", "ld1", "ld2",
- "ld3", "ld4", "ld5", "ld6", "ld7",
- "ld8", "ld9", "ld10", "ld11", "ld12",
- "ld13", "ld14", "ld15", "ld16", "ld17",
- "ldc", "ldi", "lhs", "lsc0", "lspi",
- "lvs", "pmc";
- nvidia,tristate = <0>;
- };
- conf_lc {
- nvidia,pins = "lc", "ls";
- nvidia,pull = <2>;
- };
- conf_lcsn {
- nvidia,pins = "lcsn", "lhp0", "lhp1", "lhp2",
- "lm0", "lm1", "lpp", "lpw0", "lpw1",
- "lpw2", "lsc1", "lsck", "lsda", "lsdi",
- "lvp0", "lvp1", "sdb";
- nvidia,tristate = <1>;
- };
- conf_ld17_0 {
- nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
- "ld23_22";
- nvidia,pull = <1>;
- };
- };
- };
-
- i2s@70002800 {
- status = "okay";
- };
-
- serial@70006000 {
- status = "okay";
- clock-frequency = <216000000>;
- };
-
- serial@70006200 {
- status = "okay";
- clock-frequency = <216000000>;
- };
-
- i2c@7000c000 {
- status = "okay";
- clock-frequency = <400000>;
-
- alc5632: alc5632@1e {
- compatible = "realtek,alc5632";
- reg = <0x1e>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- };
-
- i2c@7000c400 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- nvec {
- compatible = "nvidia,nvec";
- reg = <0x7000c500 0x100>;
- interrupts = <0 92 0x04>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-frequency = <80000>;
- request-gpios = <&gpio 170 0>; /* gpio PV2 */
- slave-addr = <138>;
- };
-
- i2c@7000d000 {
- status = "okay";
- clock-frequency = <400000>;
-
- adt7461@4c {
- compatible = "adi,adt7461";
- reg = <0x4c>;
- };
- };
-
- usb@c5000000 {
- status = "okay";
- };
-
- usb@c5004000 {
- status = "okay";
- nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
- };
-
- usb@c5008000 {
- status = "okay";
- };
-
- sdhci@c8000000 {
- status = "okay";
- cd-gpios = <&gpio 173 0>; /* gpio PV5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 169 0>; /* gpio PV1 */
- bus-width = <4>;
- };
-
- sdhci@c8000600 {
- status = "okay";
- support-8bit;
- bus-width = <8>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power {
- label = "Power";
- gpios = <&gpio 79 1>; /* gpio PJ7, active low */
- linux,code = <116>; /* KEY_POWER */
- gpio-key,wakeup;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
-
- wifi {
- label = "wifi-led";
- gpios = <&gpio 24 0>; /* gpio PD0 */
- linux,default-trigger = "rfkill0";
- };
- };
-
- sound {
- compatible = "nvidia,tegra-audio-alc5632-paz00",
- "nvidia,tegra-audio-alc5632";
-
- nvidia,model = "Compal PAZ00";
-
- nvidia,audio-routing =
- "Int Spk", "SPKOUT",
- "Int Spk", "SPKOUTN",
- "Headset Mic", "MICBIAS1",
- "MIC1", "Headset Mic",
- "Headset Stereophone", "HPR",
- "Headset Stereophone", "HPL",
- "DMICDAT", "Digital Mic";
-
- nvidia,audio-codec = <&alc5632>;
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- };
-};
+++ /dev/null
-/dts-v1/;
-
-/include/ "tegra20.dtsi"
-
-/ {
- model = "NVIDIA Seaboard";
- compatible = "nvidia,seaboard", "nvidia,tegra20";
-
- memory {
- reg = <0x00000000 0x40000000>;
- };
-
- pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinmux {
- ata {
- nvidia,pins = "ata";
- nvidia,function = "ide";
- };
- atb {
- nvidia,pins = "atb", "gma", "gme";
- nvidia,function = "sdio4";
- };
- atc {
- nvidia,pins = "atc";
- nvidia,function = "nand";
- };
- atd {
- nvidia,pins = "atd", "ate", "gmb", "spia",
- "spib", "spic";
- nvidia,function = "gmi";
- };
- cdev1 {
- nvidia,pins = "cdev1";
- nvidia,function = "plla_out";
- };
- cdev2 {
- nvidia,pins = "cdev2";
- nvidia,function = "pllp_out4";
- };
- crtp {
- nvidia,pins = "crtp", "lm1";
- nvidia,function = "crt";
- };
- csus {
- nvidia,pins = "csus";
- nvidia,function = "vi_sensor_clk";
- };
- dap1 {
- nvidia,pins = "dap1";
- nvidia,function = "dap1";
- };
- dap2 {
- nvidia,pins = "dap2";
- nvidia,function = "dap2";
- };
- dap3 {
- nvidia,pins = "dap3";
- nvidia,function = "dap3";
- };
- dap4 {
- nvidia,pins = "dap4";
- nvidia,function = "dap4";
- };
- ddc {
- nvidia,pins = "ddc", "owc", "spdi", "spdo",
- "uac";
- nvidia,function = "rsvd2";
- };
- dta {
- nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
- nvidia,function = "vi";
- };
- dtf {
- nvidia,pins = "dtf";
- nvidia,function = "i2c3";
- };
- gmc {
- nvidia,pins = "gmc";
- nvidia,function = "uartd";
- };
- gmd {
- nvidia,pins = "gmd";
- nvidia,function = "sflash";
- };
- gpu {
- nvidia,pins = "gpu";
- nvidia,function = "pwm";
- };
- gpu7 {
- nvidia,pins = "gpu7";
- nvidia,function = "rtck";
- };
- gpv {
- nvidia,pins = "gpv", "slxa", "slxk";
- nvidia,function = "pcie";
- };
- hdint {
- nvidia,pins = "hdint", "lpw0", "lpw2", "lsc1",
- "lsck", "lsda";
- nvidia,function = "hdmi";
- };
- i2cp {
- nvidia,pins = "i2cp";
- nvidia,function = "i2cp";
- };
- irrx {
- nvidia,pins = "irrx", "irtx";
- nvidia,function = "uartb";
- };
- kbca {
- nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
- "kbce", "kbcf";
- nvidia,function = "kbc";
- };
- lcsn {
- nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
- "lsdi", "lvp0";
- nvidia,function = "rsvd4";
- };
- ld0 {
- nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
- "ld5", "ld6", "ld7", "ld8", "ld9",
- "ld10", "ld11", "ld12", "ld13", "ld14",
- "ld15", "ld16", "ld17", "ldi", "lhp0",
- "lhp1", "lhp2", "lhs", "lpp", "lsc0",
- "lspi", "lvp1", "lvs";
- nvidia,function = "displaya";
- };
- pmc {
- nvidia,pins = "pmc";
- nvidia,function = "pwr_on";
- };
- pta {
- nvidia,pins = "pta";
- nvidia,function = "i2c2";
- };
- rm {
- nvidia,pins = "rm";
- nvidia,function = "i2c1";
- };
- sdb {
- nvidia,pins = "sdb", "sdc", "sdd";
- nvidia,function = "sdio3";
- };
- sdio1 {
- nvidia,pins = "sdio1";
- nvidia,function = "sdio1";
- };
- slxc {
- nvidia,pins = "slxc", "slxd";
- nvidia,function = "spdif";
- };
- spid {
- nvidia,pins = "spid", "spie", "spif";
- nvidia,function = "spi1";
- };
- spig {
- nvidia,pins = "spig", "spih";
- nvidia,function = "spi2_alt";
- };
- uaa {
- nvidia,pins = "uaa", "uab", "uda";
- nvidia,function = "ulpi";
- };
- uad {
- nvidia,pins = "uad";
- nvidia,function = "irda";
- };
- uca {
- nvidia,pins = "uca", "ucb";
- nvidia,function = "uartc";
- };
- conf_ata {
- nvidia,pins = "ata", "atb", "atc", "atd",
- "cdev1", "cdev2", "dap1", "dap2",
- "dap4", "dtf", "gma", "gmc", "gmd",
- "gme", "gpu", "gpu7", "i2cp", "irrx",
- "irtx", "pta", "rm", "sdc", "sdd",
- "slxd", "slxk", "spdi", "spdo", "uac",
- "uad", "uca", "ucb", "uda";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- conf_ate {
- nvidia,pins = "ate", "csus", "dap3", "ddc",
- "gpv", "owc", "slxc", "spib", "spid",
- "spie";
- nvidia,pull = <0>;
- nvidia,tristate = <1>;
- };
- conf_ck32 {
- nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
- "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
- nvidia,pull = <0>;
- };
- conf_crtp {
- nvidia,pins = "crtp", "gmb", "slxa", "spia",
- "spig", "spih";
- nvidia,pull = <2>;
- nvidia,tristate = <1>;
- };
- conf_dta {
- nvidia,pins = "dta", "dtb", "dtc", "dtd";
- nvidia,pull = <1>;
- nvidia,tristate = <0>;
- };
- conf_dte {
- nvidia,pins = "dte", "spif";
- nvidia,pull = <1>;
- nvidia,tristate = <1>;
- };
- conf_hdint {
- nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
- "lpw1", "lsc1", "lsck", "lsda", "lsdi",
- "lvp0";
- nvidia,tristate = <1>;
- };
- conf_kbca {
- nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
- "kbce", "kbcf", "sdio1", "spic", "uaa",
- "uab";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- conf_lc {
- nvidia,pins = "lc", "ls";
- nvidia,pull = <2>;
- };
- conf_ld0 {
- nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
- "ld5", "ld6", "ld7", "ld8", "ld9",
- "ld10", "ld11", "ld12", "ld13", "ld14",
- "ld15", "ld16", "ld17", "ldi", "lhp0",
- "lhp1", "lhp2", "lhs", "lm0", "lpp",
- "lpw0", "lpw2", "lsc0", "lspi", "lvp1",
- "lvs", "pmc", "sdb";
- nvidia,tristate = <0>;
- };
- conf_ld17_0 {
- nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
- "ld23_22";
- nvidia,pull = <1>;
- };
- drive_sdio1 {
- nvidia,pins = "drive_sdio1";
- nvidia,high-speed-mode = <0>;
- nvidia,schmitt = <0>;
- nvidia,low-power-mode = <3>;
- nvidia,pull-down-strength = <31>;
- nvidia,pull-up-strength = <31>;
- nvidia,slew-rate-rising = <3>;
- nvidia,slew-rate-falling = <3>;
- };
- };
- };
-
- i2s@70002800 {
- status = "okay";
- };
-
- serial@70006300 {
- status = "okay";
- clock-frequency = <216000000>;
- };
-
- i2c@7000c000 {
- status = "okay";
- clock-frequency = <400000>;
-
- wm8903: wm8903@1a {
- compatible = "wlf,wm8903";
- reg = <0x1a>;
- interrupt-parent = <&gpio>;
- interrupts = <187 0x04>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- micdet-cfg = <0>;
- micdet-delay = <100>;
- gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
- };
-
- /* ALS and proximity sensor */
- isl29018@44 {
- compatible = "isil,isl29018";
- reg = <0x44>;
- interrupt-parent = <&gpio>;
- interrupts = <202 0x04>; /* GPIO PZ2 */
- };
-
- gyrometer@68 {
- compatible = "invn,mpu3050";
- reg = <0x68>;
- interrupt-parent = <&gpio>;
- interrupts = <204 0x04>; /* gpio PZ4 */
- };
- };
-
- i2c@7000c400 {
- status = "okay";
- clock-frequency = <100000>;
-
- smart-battery@b {
- compatible = "ti,bq20z75", "smart-battery-1.1";
- reg = <0xb>;
- ti,i2c-retry-count = <2>;
- ti,poll-retry-count = <10>;
- };
- };
-
- i2c@7000c500 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000d000 {
- status = "okay";
- clock-frequency = <400000>;
-
- temperature-sensor@4c {
- compatible = "nct1008";
- reg = <0x4c>;
- };
-
- magnetometer@c {
- compatible = "ak8975";
- reg = <0xc>;
- interrupt-parent = <&gpio>;
- interrupts = <109 0x04>; /* gpio PN5 */
- };
- };
-
- emc {
- emc-table@190000 {
- reg = <190000>;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = <190000>;
- nvidia,emc-registers = <0x0000000c 0x00000026
- 0x00000009 0x00000003 0x00000004 0x00000004
- 0x00000002 0x0000000c 0x00000003 0x00000003
- 0x00000002 0x00000001 0x00000004 0x00000005
- 0x00000004 0x00000009 0x0000000d 0x0000059f
- 0x00000000 0x00000003 0x00000003 0x00000003
- 0x00000003 0x00000001 0x0000000b 0x000000c8
- 0x00000003 0x00000007 0x00000004 0x0000000f
- 0x00000002 0x00000000 0x00000000 0x00000002
- 0x00000000 0x00000000 0x00000083 0xa06204ae
- 0x007dc010 0x00000000 0x00000000 0x00000000
- 0x00000000 0x00000000 0x00000000 0x00000000>;
- };
-
- emc-table@380000 {
- reg = <380000>;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = <380000>;
- nvidia,emc-registers = <0x00000017 0x0000004b
- 0x00000012 0x00000006 0x00000004 0x00000005
- 0x00000003 0x0000000c 0x00000006 0x00000006
- 0x00000003 0x00000001 0x00000004 0x00000005
- 0x00000004 0x00000009 0x0000000d 0x00000b5f
- 0x00000000 0x00000003 0x00000003 0x00000006
- 0x00000006 0x00000001 0x00000011 0x000000c8
- 0x00000003 0x0000000e 0x00000007 0x0000000f
- 0x00000002 0x00000000 0x00000000 0x00000002
- 0x00000000 0x00000000 0x00000083 0xe044048b
- 0x007d8010 0x00000000 0x00000000 0x00000000
- 0x00000000 0x00000000 0x00000000 0x00000000>;
- };
- };
-
- usb@c5000000 {
- status = "okay";
- nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */
- dr_mode = "otg";
- };
-
- usb@c5004000 {
- status = "okay";
- nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
- };
-
- usb@c5008000 {
- status = "okay";
- };
-
- sdhci@c8000400 {
- status = "okay";
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 70 0>; /* gpio PI6 */
- bus-width = <4>;
- };
-
- sdhci@c8000600 {
- status = "okay";
- support-8bit;
- bus-width = <8>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- power {
- label = "Power";
- gpios = <&gpio 170 1>; /* gpio PV2, active low */
- linux,code = <116>; /* KEY_POWER */
- gpio-key,wakeup;
- };
-
- lid {
- label = "Lid";
- gpios = <&gpio 23 0>; /* gpio PC7 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0>; /* SW_LID */
- debounce-interval = <1>;
- gpio-key,wakeup;
- };
- };
-
- sound {
- compatible = "nvidia,tegra-audio-wm8903-seaboard",
- "nvidia,tegra-audio-wm8903";
- nvidia,model = "NVIDIA Tegra Seaboard";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1R", "Mic Jack";
-
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&wm8903 2 0>;
- nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
- };
-};
+++ /dev/null
-/dts-v1/;
-
-/include/ "tegra20.dtsi"
-
-/ {
- model = "Compulab TrimSlice board";
- compatible = "compulab,trimslice", "nvidia,tegra20";
-
- memory {
- reg = <0x00000000 0x40000000>;
- };
-
- pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinmux {
- ata {
- nvidia,pins = "ata";
- nvidia,function = "ide";
- };
- atb {
- nvidia,pins = "atb", "gma";
- nvidia,function = "sdio4";
- };
- atc {
- nvidia,pins = "atc", "gmb";
- nvidia,function = "nand";
- };
- atd {
- nvidia,pins = "atd", "ate", "gme", "pta";
- nvidia,function = "gmi";
- };
- cdev1 {
- nvidia,pins = "cdev1";
- nvidia,function = "plla_out";
- };
- cdev2 {
- nvidia,pins = "cdev2";
- nvidia,function = "pllp_out4";
- };
- crtp {
- nvidia,pins = "crtp";
- nvidia,function = "crt";
- };
- csus {
- nvidia,pins = "csus";
- nvidia,function = "vi_sensor_clk";
- };
- dap1 {
- nvidia,pins = "dap1";
- nvidia,function = "dap1";
- };
- dap2 {
- nvidia,pins = "dap2";
- nvidia,function = "dap2";
- };
- dap3 {
- nvidia,pins = "dap3";
- nvidia,function = "dap3";
- };
- dap4 {
- nvidia,pins = "dap4";
- nvidia,function = "dap4";
- };
- ddc {
- nvidia,pins = "ddc";
- nvidia,function = "i2c2";
- };
- dta {
- nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
- nvidia,function = "vi";
- };
- dtf {
- nvidia,pins = "dtf";
- nvidia,function = "i2c3";
- };
- gmc {
- nvidia,pins = "gmc", "gmd";
- nvidia,function = "sflash";
- };
- gpu {
- nvidia,pins = "gpu";
- nvidia,function = "uarta";
- };
- gpu7 {
- nvidia,pins = "gpu7";
- nvidia,function = "rtck";
- };
- gpv {
- nvidia,pins = "gpv", "slxa", "slxk";
- nvidia,function = "pcie";
- };
- hdint {
- nvidia,pins = "hdint";
- nvidia,function = "hdmi";
- };
- i2cp {
- nvidia,pins = "i2cp";
- nvidia,function = "i2cp";
- };
- irrx {
- nvidia,pins = "irrx", "irtx";
- nvidia,function = "uartb";
- };
- kbca {
- nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
- "kbce", "kbcf";
- nvidia,function = "kbc";
- };
- lcsn {
- nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
- "ld3", "ld4", "ld5", "ld6", "ld7",
- "ld8", "ld9", "ld10", "ld11", "ld12",
- "ld13", "ld14", "ld15", "ld16", "ld17",
- "ldc", "ldi", "lhp0", "lhp1", "lhp2",
- "lhs", "lm0", "lm1", "lpp", "lpw0",
- "lpw1", "lpw2", "lsc0", "lsc1", "lsck",
- "lsda", "lsdi", "lspi", "lvp0", "lvp1",
- "lvs";
- nvidia,function = "displaya";
- };
- owc {
- nvidia,pins = "owc", "uac";
- nvidia,function = "rsvd2";
- };
- pmc {
- nvidia,pins = "pmc";
- nvidia,function = "pwr_on";
- };
- rm {
- nvidia,pins = "rm";
- nvidia,function = "i2c1";
- };
- sdb {
- nvidia,pins = "sdb", "sdc", "sdd";
- nvidia,function = "pwm";
- };
- sdio1 {
- nvidia,pins = "sdio1";
- nvidia,function = "sdio1";
- };
- slxc {
- nvidia,pins = "slxc", "slxd";
- nvidia,function = "sdio3";
- };
- spdi {
- nvidia,pins = "spdi", "spdo";
- nvidia,function = "spdif";
- };
- spia {
- nvidia,pins = "spia", "spib", "spic";
- nvidia,function = "spi2";
- };
- spid {
- nvidia,pins = "spid", "spie", "spif";
- nvidia,function = "spi1";
- };
- spig {
- nvidia,pins = "spig", "spih";
- nvidia,function = "spi2_alt";
- };
- uaa {
- nvidia,pins = "uaa", "uab", "uda";
- nvidia,function = "ulpi";
- };
- uad {
- nvidia,pins = "uad";
- nvidia,function = "irda";
- };
- uca {
- nvidia,pins = "uca", "ucb";
- nvidia,function = "uartc";
- };
- conf_ata {
- nvidia,pins = "ata", "atc", "atd", "ate",
- "crtp", "dap2", "dap3", "dap4", "dta",
- "dtb", "dtc", "dtd", "dte", "gmb",
- "gme", "i2cp", "pta", "slxc", "slxd",
- "spdi", "spdo", "uda";
- nvidia,pull = <0>;
- nvidia,tristate = <1>;
- };
- conf_atb {
- nvidia,pins = "atb", "cdev1", "cdev2", "dap1",
- "gma", "gmc", "gmd", "gpu", "gpu7",
- "gpv", "sdio1", "slxa", "slxk", "uac";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- conf_ck32 {
- nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
- "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
- nvidia,pull = <0>;
- };
- conf_csus {
- nvidia,pins = "csus", "spia", "spib",
- "spid", "spif";
- nvidia,pull = <1>;
- nvidia,tristate = <1>;
- };
- conf_ddc {
- nvidia,pins = "ddc", "dtf", "rm", "sdc", "sdd";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- conf_hdint {
- nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
- "lpw1", "lsc1", "lsck", "lsda", "lsdi",
- "lvp0", "pmc";
- nvidia,tristate = <1>;
- };
- conf_irrx {
- nvidia,pins = "irrx", "irtx", "kbca", "kbcb",
- "kbcc", "kbcd", "kbce", "kbcf", "owc",
- "spic", "spie", "spig", "spih", "uaa",
- "uab", "uad", "uca", "ucb";
- nvidia,pull = <2>;
- nvidia,tristate = <1>;
- };
- conf_lc {
- nvidia,pins = "lc", "ls";
- nvidia,pull = <2>;
- };
- conf_ld0 {
- nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
- "ld5", "ld6", "ld7", "ld8", "ld9",
- "ld10", "ld11", "ld12", "ld13", "ld14",
- "ld15", "ld16", "ld17", "ldi", "lhp0",
- "lhp1", "lhp2", "lhs", "lm0", "lpp",
- "lpw0", "lpw2", "lsc0", "lspi", "lvp1",
- "lvs", "sdb";
- nvidia,tristate = <0>;
- };
- conf_ld17_0 {
- nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
- "ld23_22";
- nvidia,pull = <1>;
- };
- };
- };
-
- i2s@70002800 {
- status = "okay";
- };
-
- serial@70006000 {
- status = "okay";
- clock-frequency = <216000000>;
- };
-
- i2c@7000c000 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000c400 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000c500 {
- status = "okay";
- clock-frequency = <400000>;
-
- codec: codec@1a {
- compatible = "ti,tlv320aic23";
- reg = <0x1a>;
- };
-
- rtc@56 {
- compatible = "emmicro,em3027";
- reg = <0x56>;
- };
- };
-
- usb@c5000000 {
- status = "okay";
- };
-
- usb@c5004000 {
- nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
- };
-
- usb@c5008000 {
- status = "okay";
- };
-
- sdhci@c8000000 {
- status = "okay";
- bus-width = <4>;
- };
-
- sdhci@c8000600 {
- status = "okay";
- cd-gpios = <&gpio 121 0>; /* gpio PP1 */
- wp-gpios = <&gpio 122 0>; /* gpio PP2 */
- bus-width = <4>;
- };
-
- sound {
- compatible = "nvidia,tegra-audio-trimslice";
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&codec>;
- };
-};
+++ /dev/null
-/dts-v1/;
-
-/include/ "tegra20.dtsi"
-
-/ {
- model = "NVIDIA Tegra2 Ventana evaluation board";
- compatible = "nvidia,ventana", "nvidia,tegra20";
-
- memory {
- reg = <0x00000000 0x40000000>;
- };
-
- pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinmux {
- ata {
- nvidia,pins = "ata";
- nvidia,function = "ide";
- };
- atb {
- nvidia,pins = "atb", "gma", "gme";
- nvidia,function = "sdio4";
- };
- atc {
- nvidia,pins = "atc";
- nvidia,function = "nand";
- };
- atd {
- nvidia,pins = "atd", "ate", "gmb", "spia",
- "spib", "spic";
- nvidia,function = "gmi";
- };
- cdev1 {
- nvidia,pins = "cdev1";
- nvidia,function = "plla_out";
- };
- cdev2 {
- nvidia,pins = "cdev2";
- nvidia,function = "pllp_out4";
- };
- crtp {
- nvidia,pins = "crtp", "lm1";
- nvidia,function = "crt";
- };
- csus {
- nvidia,pins = "csus";
- nvidia,function = "vi_sensor_clk";
- };
- dap1 {
- nvidia,pins = "dap1";
- nvidia,function = "dap1";
- };
- dap2 {
- nvidia,pins = "dap2";
- nvidia,function = "dap2";
- };
- dap3 {
- nvidia,pins = "dap3";
- nvidia,function = "dap3";
- };
- dap4 {
- nvidia,pins = "dap4";
- nvidia,function = "dap4";
- };
- ddc {
- nvidia,pins = "ddc", "owc", "spdi", "spdo",
- "uac";
- nvidia,function = "rsvd2";
- };
- dta {
- nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
- nvidia,function = "vi";
- };
- dtf {
- nvidia,pins = "dtf";
- nvidia,function = "i2c3";
- };
- gmc {
- nvidia,pins = "gmc";
- nvidia,function = "uartd";
- };
- gmd {
- nvidia,pins = "gmd";
- nvidia,function = "sflash";
- };
- gpu {
- nvidia,pins = "gpu";
- nvidia,function = "pwm";
- };
- gpu7 {
- nvidia,pins = "gpu7";
- nvidia,function = "rtck";
- };
- gpv {
- nvidia,pins = "gpv", "slxa", "slxk";
- nvidia,function = "pcie";
- };
- hdint {
- nvidia,pins = "hdint", "pta";
- nvidia,function = "hdmi";
- };
- i2cp {
- nvidia,pins = "i2cp";
- nvidia,function = "i2cp";
- };
- irrx {
- nvidia,pins = "irrx", "irtx";
- nvidia,function = "uartb";
- };
- kbca {
- nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
- "kbce", "kbcf";
- nvidia,function = "kbc";
- };
- lcsn {
- nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
- "lsdi", "lvp0";
- nvidia,function = "rsvd4";
- };
- ld0 {
- nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
- "ld5", "ld6", "ld7", "ld8", "ld9",
- "ld10", "ld11", "ld12", "ld13", "ld14",
- "ld15", "ld16", "ld17", "ldi", "lhp0",
- "lhp1", "lhp2", "lhs", "lpp", "lpw0",
- "lpw2", "lsc0", "lsc1", "lsck", "lsda",
- "lspi", "lvp1", "lvs";
- nvidia,function = "displaya";
- };
- pmc {
- nvidia,pins = "pmc";
- nvidia,function = "pwr_on";
- };
- rm {
- nvidia,pins = "rm";
- nvidia,function = "i2c1";
- };
- sdb {
- nvidia,pins = "sdb", "sdc", "sdd", "slxc";
- nvidia,function = "sdio3";
- };
- sdio1 {
- nvidia,pins = "sdio1";
- nvidia,function = "sdio1";
- };
- slxd {
- nvidia,pins = "slxd";
- nvidia,function = "spdif";
- };
- spid {
- nvidia,pins = "spid", "spie", "spif";
- nvidia,function = "spi1";
- };
- spig {
- nvidia,pins = "spig", "spih";
- nvidia,function = "spi2_alt";
- };
- uaa {
- nvidia,pins = "uaa", "uab", "uda";
- nvidia,function = "ulpi";
- };
- uad {
- nvidia,pins = "uad";
- nvidia,function = "irda";
- };
- uca {
- nvidia,pins = "uca", "ucb";
- nvidia,function = "uartc";
- };
- conf_ata {
- nvidia,pins = "ata", "atb", "atc", "atd",
- "cdev1", "cdev2", "dap1", "dap2",
- "dap4", "ddc", "dtf", "gma", "gmc",
- "gme", "gpu", "gpu7", "i2cp", "irrx",
- "irtx", "pta", "rm", "sdc", "sdd",
- "slxc", "slxd", "slxk", "spdi", "spdo",
- "uac", "uad", "uca", "ucb", "uda";
- nvidia,pull = <0>;
- nvidia,tristate = <0>;
- };
- conf_ate {
- nvidia,pins = "ate", "csus", "dap3", "gmd",
- "gpv", "owc", "spia", "spib", "spic",
- "spid", "spie", "spig";
- nvidia,pull = <0>;
- nvidia,tristate = <1>;
- };
- conf_ck32 {
- nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
- "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
- nvidia,pull = <0>;
- };
- conf_crtp {
- nvidia,pins = "crtp", "gmb", "slxa", "spih";
- nvidia,pull = <2>;
- nvidia,tristate = <1>;
- };
- conf_dta {
- nvidia,pins = "dta", "dtb", "dtc", "dtd";
- nvidia,pull = <1>;
- nvidia,tristate = <0>;
- };
- conf_dte {
- nvidia,pins = "dte", "spif";
- nvidia,pull = <1>;
- nvidia,tristate = <1>;
- };
- conf_hdint {
- nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
- "lpw1", "lsck", "lsda", "lsdi", "lvp0";
- nvidia,tristate = <1>;
- };
- conf_kbca {
- nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
- "kbce", "kbcf", "sdio1", "uaa", "uab";
- nvidia,pull = <2>;
- nvidia,tristate = <0>;
- };
- conf_lc {
- nvidia,pins = "lc", "ls";
- nvidia,pull = <2>;
- };
- conf_ld0 {
- nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
- "ld5", "ld6", "ld7", "ld8", "ld9",
- "ld10", "ld11", "ld12", "ld13", "ld14",
- "ld15", "ld16", "ld17", "ldi", "lhp0",
- "lhp1", "lhp2", "lhs", "lm0", "lpp",
- "lpw0", "lpw2", "lsc0", "lsc1", "lspi",
- "lvp1", "lvs", "pmc", "sdb";
- nvidia,tristate = <0>;
- };
- conf_ld17_0 {
- nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
- "ld23_22";
- nvidia,pull = <1>;
- };
- };
- };
-
- i2s@70002800 {
- status = "okay";
- };
-
- serial@70006300 {
- status = "okay";
- clock-frequency = <216000000>;
- };
-
- i2c@7000c000 {
- status = "okay";
- clock-frequency = <400000>;
-
- wm8903: wm8903@1a {
- compatible = "wlf,wm8903";
- reg = <0x1a>;
- interrupt-parent = <&gpio>;
- interrupts = <187 0x04>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- micdet-cfg = <0>;
- micdet-delay = <100>;
- gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
- };
-
- /* ALS and proximity sensor */
- isl29018@44 {
- compatible = "isil,isl29018";
- reg = <0x44>;
- interrupt-parent = <&gpio>;
- interrupts = <202 0x04>; /*gpio PZ2 */
- };
- };
-
- i2c@7000c400 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000c500 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- i2c@7000d000 {
- status = "okay";
- clock-frequency = <400000>;
- };
-
- usb@c5000000 {
- status = "okay";
- };
-
- usb@c5004000 {
- status = "okay";
- nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
- };
-
- usb@c5008000 {
- status = "okay";
- };
-
- sdhci@c8000400 {
- status = "okay";
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 70 0>; /* gpio PI6 */
- bus-width = <4>;
- };
-
- sdhci@c8000600 {
- status = "okay";
- support-8bit;
- bus-width = <8>;
- };
-
- sound {
- compatible = "nvidia,tegra-audio-wm8903-ventana",
- "nvidia,tegra-audio-wm8903";
- nvidia,model = "NVIDIA Tegra Ventana";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1L", "Mic Jack";
-
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&wm8903 2 0>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- nvidia,int-mic-en-gpios = <&gpio 184 0>; /* gpio PX0 */
- nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
- };
-};
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra20.dtsi"
+
+/ {
+ model = "NVIDIA Tegra2 Harmony evaluation board";
+ compatible = "nvidia,harmony", "nvidia,tegra20";
+
+ memory {
+ reg = <0x00000000 0x40000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ata {
+ nvidia,pins = "ata";
+ nvidia,function = "ide";
+ };
+ atb {
+ nvidia,pins = "atb", "gma", "gme";
+ nvidia,function = "sdio4";
+ };
+ atc {
+ nvidia,pins = "atc";
+ nvidia,function = "nand";
+ };
+ atd {
+ nvidia,pins = "atd", "ate", "gmb", "gmd", "gpu",
+ "spia", "spib", "spic";
+ nvidia,function = "gmi";
+ };
+ cdev1 {
+ nvidia,pins = "cdev1";
+ nvidia,function = "plla_out";
+ };
+ cdev2 {
+ nvidia,pins = "cdev2";
+ nvidia,function = "pllp_out4";
+ };
+ crtp {
+ nvidia,pins = "crtp";
+ nvidia,function = "crt";
+ };
+ csus {
+ nvidia,pins = "csus";
+ nvidia,function = "vi_sensor_clk";
+ };
+ dap1 {
+ nvidia,pins = "dap1";
+ nvidia,function = "dap1";
+ };
+ dap2 {
+ nvidia,pins = "dap2";
+ nvidia,function = "dap2";
+ };
+ dap3 {
+ nvidia,pins = "dap3";
+ nvidia,function = "dap3";
+ };
+ dap4 {
+ nvidia,pins = "dap4";
+ nvidia,function = "dap4";
+ };
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "i2c2";
+ };
+ dta {
+ nvidia,pins = "dta", "dtd";
+ nvidia,function = "sdio2";
+ };
+ dtb {
+ nvidia,pins = "dtb", "dtc", "dte";
+ nvidia,function = "rsvd1";
+ };
+ dtf {
+ nvidia,pins = "dtf";
+ nvidia,function = "i2c3";
+ };
+ gmc {
+ nvidia,pins = "gmc";
+ nvidia,function = "uartd";
+ };
+ gpu7 {
+ nvidia,pins = "gpu7";
+ nvidia,function = "rtck";
+ };
+ gpv {
+ nvidia,pins = "gpv", "slxa", "slxk";
+ nvidia,function = "pcie";
+ };
+ hdint {
+ nvidia,pins = "hdint", "pta";
+ nvidia,function = "hdmi";
+ };
+ i2cp {
+ nvidia,pins = "i2cp";
+ nvidia,function = "i2cp";
+ };
+ irrx {
+ nvidia,pins = "irrx", "irtx";
+ nvidia,function = "uarta";
+ };
+ kbca {
+ nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+ "kbce", "kbcf";
+ nvidia,function = "kbc";
+ };
+ lcsn {
+ nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
+ "ld3", "ld4", "ld5", "ld6", "ld7",
+ "ld8", "ld9", "ld10", "ld11", "ld12",
+ "ld13", "ld14", "ld15", "ld16", "ld17",
+ "ldc", "ldi", "lhp0", "lhp1", "lhp2",
+ "lhs", "lm0", "lm1", "lpp", "lpw0",
+ "lpw1", "lpw2", "lsc0", "lsc1", "lsck",
+ "lsda", "lsdi", "lspi", "lvp0", "lvp1",
+ "lvs";
+ nvidia,function = "displaya";
+ };
+ owc {
+ nvidia,pins = "owc", "spdi", "spdo", "uac";
+ nvidia,function = "rsvd2";
+ };
+ pmc {
+ nvidia,pins = "pmc";
+ nvidia,function = "pwr_on";
+ };
+ rm {
+ nvidia,pins = "rm";
+ nvidia,function = "i2c1";
+ };
+ sdb {
+ nvidia,pins = "sdb", "sdc", "sdd";
+ nvidia,function = "pwm";
+ };
+ sdio1 {
+ nvidia,pins = "sdio1";
+ nvidia,function = "sdio1";
+ };
+ slxc {
+ nvidia,pins = "slxc", "slxd";
+ nvidia,function = "spdif";
+ };
+ spid {
+ nvidia,pins = "spid", "spie", "spif";
+ nvidia,function = "spi1";
+ };
+ spig {
+ nvidia,pins = "spig", "spih";
+ nvidia,function = "spi2_alt";
+ };
+ uaa {
+ nvidia,pins = "uaa", "uab", "uda";
+ nvidia,function = "ulpi";
+ };
+ uad {
+ nvidia,pins = "uad";
+ nvidia,function = "irda";
+ };
+ uca {
+ nvidia,pins = "uca", "ucb";
+ nvidia,function = "uartc";
+ };
+ conf_ata {
+ nvidia,pins = "ata", "atb", "atc", "atd", "ate",
+ "cdev1", "cdev2", "dap1", "dtb", "gma",
+ "gmb", "gmc", "gmd", "gme", "gpu7",
+ "gpv", "i2cp", "pta", "rm", "slxa",
+ "slxk", "spia", "spib", "uac";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ conf_ck32 {
+ nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+ "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+ nvidia,pull = <0>;
+ };
+ conf_csus {
+ nvidia,pins = "csus", "spid", "spif";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ };
+ conf_crtp {
+ nvidia,pins = "crtp", "dap2", "dap3", "dap4",
+ "dtc", "dte", "dtf", "gpu", "sdio1",
+ "slxc", "slxd", "spdi", "spdo", "spig",
+ "uda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ };
+ conf_ddc {
+ nvidia,pins = "ddc", "dta", "dtd", "kbca",
+ "kbcb", "kbcc", "kbcd", "kbce", "kbcf",
+ "sdc";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ conf_hdint {
+ nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+ "lpw1", "lsc1", "lsck", "lsda", "lsdi",
+ "lvp0", "owc", "sdb";
+ nvidia,tristate = <1>;
+ };
+ conf_irrx {
+ nvidia,pins = "irrx", "irtx", "sdd", "spic",
+ "spie", "spih", "uaa", "uab", "uad",
+ "uca", "ucb";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ };
+ conf_lc {
+ nvidia,pins = "lc", "ls";
+ nvidia,pull = <2>;
+ };
+ conf_ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldi", "lhp0",
+ "lhp1", "lhp2", "lhs", "lm0", "lpp",
+ "lpw0", "lpw2", "lsc0", "lspi", "lvp1",
+ "lvs", "pmc";
+ nvidia,tristate = <0>;
+ };
+ conf_ld17_0 {
+ nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+ "ld23_22";
+ nvidia,pull = <1>;
+ };
+ };
+ };
+
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006300 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ wm8903: wm8903@1a {
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <187 0x04>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ pmc {
+ nvidia,invert-interrupt;
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ };
+
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000200 {
+ status = "okay";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 155 0>; /* gpio PT3 */
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ cd-gpios = <&gpio 58 0>; /* gpio PH2 */
+ wp-gpios = <&gpio 59 0>; /* gpio PH3 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
+ bus-width = <8>;
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-harmony",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Harmony";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+ };
+};
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra20.dtsi"
+
+/ {
+ model = "Toshiba AC100 / Dynabook AZ";
+ compatible = "compal,paz00", "nvidia,tegra20";
+
+ memory {
+ reg = <0x00000000 0x20000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ata {
+ nvidia,pins = "ata", "atc", "atd", "ate",
+ "dap2", "gmb", "gmc", "gmd", "spia",
+ "spib", "spic", "spid", "spie";
+ nvidia,function = "gmi";
+ };
+ atb {
+ nvidia,pins = "atb", "gma", "gme";
+ nvidia,function = "sdio4";
+ };
+ cdev1 {
+ nvidia,pins = "cdev1";
+ nvidia,function = "plla_out";
+ };
+ cdev2 {
+ nvidia,pins = "cdev2";
+ nvidia,function = "pllp_out4";
+ };
+ crtp {
+ nvidia,pins = "crtp";
+ nvidia,function = "crt";
+ };
+ csus {
+ nvidia,pins = "csus";
+ nvidia,function = "pllc_out1";
+ };
+ dap1 {
+ nvidia,pins = "dap1";
+ nvidia,function = "dap1";
+ };
+ dap3 {
+ nvidia,pins = "dap3";
+ nvidia,function = "dap3";
+ };
+ dap4 {
+ nvidia,pins = "dap4";
+ nvidia,function = "dap4";
+ };
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "i2c2";
+ };
+ dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+ nvidia,function = "rsvd1";
+ };
+ dtf {
+ nvidia,pins = "dtf";
+ nvidia,function = "i2c3";
+ };
+ gpu {
+ nvidia,pins = "gpu", "sdb", "sdd";
+ nvidia,function = "pwm";
+ };
+ gpu7 {
+ nvidia,pins = "gpu7";
+ nvidia,function = "rtck";
+ };
+ gpv {
+ nvidia,pins = "gpv", "slxa", "slxk";
+ nvidia,function = "pcie";
+ };
+ hdint {
+ nvidia,pins = "hdint", "pta";
+ nvidia,function = "hdmi";
+ };
+ i2cp {
+ nvidia,pins = "i2cp";
+ nvidia,function = "i2cp";
+ };
+ irrx {
+ nvidia,pins = "irrx", "irtx";
+ nvidia,function = "uarta";
+ };
+ kbca {
+ nvidia,pins = "kbca", "kbcc", "kbce", "kbcf";
+ nvidia,function = "kbc";
+ };
+ kbcb {
+ nvidia,pins = "kbcb", "kbcd";
+ nvidia,function = "sdio2";
+ };
+ lcsn {
+ nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
+ "ld3", "ld4", "ld5", "ld6", "ld7",
+ "ld8", "ld9", "ld10", "ld11", "ld12",
+ "ld13", "ld14", "ld15", "ld16", "ld17",
+ "ldc", "ldi", "lhp0", "lhp1", "lhp2",
+ "lhs", "lm0", "lm1", "lpp", "lpw0",
+ "lpw1", "lpw2", "lsc0", "lsc1", "lsck",
+ "lsda", "lsdi", "lspi", "lvp0", "lvp1",
+ "lvs";
+ nvidia,function = "displaya";
+ };
+ owc {
+ nvidia,pins = "owc";
+ nvidia,function = "owr";
+ };
+ pmc {
+ nvidia,pins = "pmc";
+ nvidia,function = "pwr_on";
+ };
+ rm {
+ nvidia,pins = "rm";
+ nvidia,function = "i2c1";
+ };
+ sdc {
+ nvidia,pins = "sdc";
+ nvidia,function = "twc";
+ };
+ sdio1 {
+ nvidia,pins = "sdio1";
+ nvidia,function = "sdio1";
+ };
+ slxc {
+ nvidia,pins = "slxc", "slxd";
+ nvidia,function = "spi4";
+ };
+ spdi {
+ nvidia,pins = "spdi", "spdo";
+ nvidia,function = "rsvd2";
+ };
+ spif {
+ nvidia,pins = "spif", "uac";
+ nvidia,function = "rsvd4";
+ };
+ spig {
+ nvidia,pins = "spig", "spih";
+ nvidia,function = "spi2_alt";
+ };
+ uaa {
+ nvidia,pins = "uaa", "uab", "uda";
+ nvidia,function = "ulpi";
+ };
+ uad {
+ nvidia,pins = "uad";
+ nvidia,function = "spdif";
+ };
+ uca {
+ nvidia,pins = "uca", "ucb";
+ nvidia,function = "uartc";
+ };
+ conf_ata {
+ nvidia,pins = "ata", "atb", "atc", "atd", "ate",
+ "cdev1", "cdev2", "dap1", "dap2", "dtf",
+ "gma", "gmb", "gmc", "gmd", "gme",
+ "gpu", "gpu7", "gpv", "i2cp", "pta",
+ "rm", "sdio1", "slxk", "spdo", "uac",
+ "uda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ conf_ck32 {
+ nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+ "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+ nvidia,pull = <0>;
+ };
+ conf_crtp {
+ nvidia,pins = "crtp", "dap3", "dap4", "dtb",
+ "dtc", "dte", "slxa", "slxc", "slxd",
+ "spdi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ };
+ conf_csus {
+ nvidia,pins = "csus", "spia", "spib", "spid",
+ "spif";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ };
+ conf_ddc {
+ nvidia,pins = "ddc", "irrx", "irtx", "kbca",
+ "kbcb", "kbcc", "kbcd", "kbce", "kbcf",
+ "spic", "spig", "uaa", "uab";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ conf_dta {
+ nvidia,pins = "dta", "dtd", "owc", "sdc", "sdd",
+ "spie", "spih", "uad", "uca", "ucb";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ };
+ conf_hdint {
+ nvidia,pins = "hdint", "ld0", "ld1", "ld2",
+ "ld3", "ld4", "ld5", "ld6", "ld7",
+ "ld8", "ld9", "ld10", "ld11", "ld12",
+ "ld13", "ld14", "ld15", "ld16", "ld17",
+ "ldc", "ldi", "lhs", "lsc0", "lspi",
+ "lvs", "pmc";
+ nvidia,tristate = <0>;
+ };
+ conf_lc {
+ nvidia,pins = "lc", "ls";
+ nvidia,pull = <2>;
+ };
+ conf_lcsn {
+ nvidia,pins = "lcsn", "lhp0", "lhp1", "lhp2",
+ "lm0", "lm1", "lpp", "lpw0", "lpw1",
+ "lpw2", "lsc1", "lsck", "lsda", "lsdi",
+ "lvp0", "lvp1", "sdb";
+ nvidia,tristate = <1>;
+ };
+ conf_ld17_0 {
+ nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+ "ld23_22";
+ nvidia,pull = <1>;
+ };
+ };
+ };
+
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006000 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ serial@70006200 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ alc5632: alc5632@1e {
+ compatible = "realtek,alc5632";
+ reg = <0x1e>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ nvec {
+ compatible = "nvidia,nvec";
+ reg = <0x7000c500 0x100>;
+ interrupts = <0 92 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <80000>;
+ request-gpios = <&gpio 170 0>; /* gpio PV2 */
+ slave-addr = <138>;
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ adt7461@4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ };
+
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000000 {
+ status = "okay";
+ cd-gpios = <&gpio 173 0>; /* gpio PV5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 169 0>; /* gpio PV1 */
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio 79 1>; /* gpio PJ7, active low */
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ wifi {
+ label = "wifi-led";
+ gpios = <&gpio 24 0>; /* gpio PD0 */
+ linux,default-trigger = "rfkill0";
+ };
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-alc5632-paz00",
+ "nvidia,tegra-audio-alc5632";
+
+ nvidia,model = "Compal PAZ00";
+
+ nvidia,audio-routing =
+ "Int Spk", "SPKOUT",
+ "Int Spk", "SPKOUTN",
+ "Headset Mic", "MICBIAS1",
+ "MIC1", "Headset Mic",
+ "Headset Stereophone", "HPR",
+ "Headset Stereophone", "HPL",
+ "DMICDAT", "Digital Mic";
+
+ nvidia,audio-codec = <&alc5632>;
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ };
+};
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra20.dtsi"
+
+/ {
+ model = "NVIDIA Seaboard";
+ compatible = "nvidia,seaboard", "nvidia,tegra20";
+
+ memory {
+ reg = <0x00000000 0x40000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ata {
+ nvidia,pins = "ata";
+ nvidia,function = "ide";
+ };
+ atb {
+ nvidia,pins = "atb", "gma", "gme";
+ nvidia,function = "sdio4";
+ };
+ atc {
+ nvidia,pins = "atc";
+ nvidia,function = "nand";
+ };
+ atd {
+ nvidia,pins = "atd", "ate", "gmb", "spia",
+ "spib", "spic";
+ nvidia,function = "gmi";
+ };
+ cdev1 {
+ nvidia,pins = "cdev1";
+ nvidia,function = "plla_out";
+ };
+ cdev2 {
+ nvidia,pins = "cdev2";
+ nvidia,function = "pllp_out4";
+ };
+ crtp {
+ nvidia,pins = "crtp", "lm1";
+ nvidia,function = "crt";
+ };
+ csus {
+ nvidia,pins = "csus";
+ nvidia,function = "vi_sensor_clk";
+ };
+ dap1 {
+ nvidia,pins = "dap1";
+ nvidia,function = "dap1";
+ };
+ dap2 {
+ nvidia,pins = "dap2";
+ nvidia,function = "dap2";
+ };
+ dap3 {
+ nvidia,pins = "dap3";
+ nvidia,function = "dap3";
+ };
+ dap4 {
+ nvidia,pins = "dap4";
+ nvidia,function = "dap4";
+ };
+ dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+ nvidia,function = "vi";
+ };
+ dtf {
+ nvidia,pins = "dtf";
+ nvidia,function = "i2c3";
+ };
+ gmc {
+ nvidia,pins = "gmc";
+ nvidia,function = "uartd";
+ };
+ gmd {
+ nvidia,pins = "gmd";
+ nvidia,function = "sflash";
+ };
+ gpu {
+ nvidia,pins = "gpu";
+ nvidia,function = "pwm";
+ };
+ gpu7 {
+ nvidia,pins = "gpu7";
+ nvidia,function = "rtck";
+ };
+ gpv {
+ nvidia,pins = "gpv", "slxa", "slxk";
+ nvidia,function = "pcie";
+ };
+ hdint {
+ nvidia,pins = "hdint", "lpw0", "lpw2", "lsc1",
+ "lsck", "lsda";
+ nvidia,function = "hdmi";
+ };
+ i2cp {
+ nvidia,pins = "i2cp";
+ nvidia,function = "i2cp";
+ };
+ irrx {
+ nvidia,pins = "irrx", "irtx";
+ nvidia,function = "uartb";
+ };
+ kbca {
+ nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+ "kbce", "kbcf";
+ nvidia,function = "kbc";
+ };
+ lcsn {
+ nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
+ "lsdi", "lvp0";
+ nvidia,function = "rsvd4";
+ };
+ ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldi", "lhp0",
+ "lhp1", "lhp2", "lhs", "lpp", "lsc0",
+ "lspi", "lvp1", "lvs";
+ nvidia,function = "displaya";
+ };
+ owc {
+ nvidia,pins = "owc", "spdi", "spdo", "uac";
+ nvidia,function = "rsvd2";
+ };
+ pmc {
+ nvidia,pins = "pmc";
+ nvidia,function = "pwr_on";
+ };
+ rm {
+ nvidia,pins = "rm";
+ nvidia,function = "i2c1";
+ };
+ sdb {
+ nvidia,pins = "sdb", "sdc", "sdd";
+ nvidia,function = "sdio3";
+ };
+ sdio1 {
+ nvidia,pins = "sdio1";
+ nvidia,function = "sdio1";
+ };
+ slxc {
+ nvidia,pins = "slxc", "slxd";
+ nvidia,function = "spdif";
+ };
+ spid {
+ nvidia,pins = "spid", "spie", "spif";
+ nvidia,function = "spi1";
+ };
+ spig {
+ nvidia,pins = "spig", "spih";
+ nvidia,function = "spi2_alt";
+ };
+ uaa {
+ nvidia,pins = "uaa", "uab", "uda";
+ nvidia,function = "ulpi";
+ };
+ uad {
+ nvidia,pins = "uad";
+ nvidia,function = "irda";
+ };
+ uca {
+ nvidia,pins = "uca", "ucb";
+ nvidia,function = "uartc";
+ };
+ conf_ata {
+ nvidia,pins = "ata", "atb", "atc", "atd",
+ "cdev1", "cdev2", "dap1", "dap2",
+ "dap4", "ddc", "dtf", "gma", "gmc", "gmd",
+ "gme", "gpu", "gpu7", "i2cp", "irrx",
+ "irtx", "pta", "rm", "sdc", "sdd",
+ "slxd", "slxk", "spdi", "spdo", "uac",
+ "uad", "uca", "ucb", "uda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ conf_ate {
+ nvidia,pins = "ate", "csus", "dap3",
+ "gpv", "owc", "slxc", "spib", "spid",
+ "spie";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ };
+ conf_ck32 {
+ nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+ "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+ nvidia,pull = <0>;
+ };
+ conf_crtp {
+ nvidia,pins = "crtp", "gmb", "slxa", "spia",
+ "spig", "spih";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ };
+ conf_dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ };
+ conf_dte {
+ nvidia,pins = "dte", "spif";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ };
+ conf_hdint {
+ nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+ "lpw1", "lsc1", "lsck", "lsda", "lsdi",
+ "lvp0";
+ nvidia,tristate = <1>;
+ };
+ conf_kbca {
+ nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+ "kbce", "kbcf", "sdio1", "spic", "uaa",
+ "uab";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ conf_lc {
+ nvidia,pins = "lc", "ls";
+ nvidia,pull = <2>;
+ };
+ conf_ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldi", "lhp0",
+ "lhp1", "lhp2", "lhs", "lm0", "lpp",
+ "lpw0", "lpw2", "lsc0", "lspi", "lvp1",
+ "lvs", "pmc", "sdb";
+ nvidia,tristate = <0>;
+ };
+ conf_ld17_0 {
+ nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+ "ld23_22";
+ nvidia,pull = <1>;
+ };
+ drive_sdio1 {
+ nvidia,pins = "drive_sdio1";
+ nvidia,high-speed-mode = <0>;
+ nvidia,schmitt = <0>;
+ nvidia,low-power-mode = <3>;
+ nvidia,pull-down-strength = <31>;
+ nvidia,pull-up-strength = <31>;
+ nvidia,slew-rate-rising = <3>;
+ nvidia,slew-rate-falling = <3>;
+ };
+ };
+
+ state_i2cmux_ddc: pinmux_i2cmux_ddc {
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "i2c2";
+ };
+ pta {
+ nvidia,pins = "pta";
+ nvidia,function = "rsvd4";
+ };
+ };
+
+ state_i2cmux_pta: pinmux_i2cmux_pta {
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "rsvd4";
+ };
+ pta {
+ nvidia,pins = "pta";
+ nvidia,function = "i2c2";
+ };
+ };
+
+ state_i2cmux_idle: pinmux_i2cmux_idle {
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "rsvd4";
+ };
+ pta {
+ nvidia,pins = "pta";
+ nvidia,function = "rsvd4";
+ };
+ };
+ };
+
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006300 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ wm8903: wm8903@1a {
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <187 0x04>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+
+ /* ALS and proximity sensor */
+ isl29018@44 {
+ compatible = "isil,isl29018";
+ reg = <0x44>;
+ interrupt-parent = <&gpio>;
+ interrupts = <202 0x04>; /* GPIO PZ2 */
+ };
+
+ gyrometer@68 {
+ compatible = "invn,mpu3050";
+ reg = <0x68>;
+ interrupt-parent = <&gpio>;
+ interrupts = <204 0x04>; /* gpio PZ4 */
+ };
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ i2cmux {
+ compatible = "i2c-mux-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c-parent = <&{/i2c@7000c400}>;
+
+ pinctrl-names = "ddc", "pta", "idle";
+ pinctrl-0 = <&state_i2cmux_ddc>;
+ pinctrl-1 = <&state_i2cmux_pta>;
+ pinctrl-2 = <&state_i2cmux_idle>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smart-battery@b {
+ compatible = "ti,bq20z75", "smart-battery-1.1";
+ reg = <0xb>;
+ ti,i2c-retry-count = <2>;
+ ti,poll-retry-count = <10>;
+ };
+ };
+ };
+
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ temperature-sensor@4c {
+ compatible = "nct1008";
+ reg = <0x4c>;
+ };
+
+ magnetometer@c {
+ compatible = "ak8975";
+ reg = <0xc>;
+ interrupt-parent = <&gpio>;
+ interrupts = <109 0x04>; /* gpio PN5 */
+ };
+ };
+
+ memory-controller@0x7000f400 {
+ emc-table@190000 {
+ reg = <190000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = <190000>;
+ nvidia,emc-registers = <0x0000000c 0x00000026
+ 0x00000009 0x00000003 0x00000004 0x00000004
+ 0x00000002 0x0000000c 0x00000003 0x00000003
+ 0x00000002 0x00000001 0x00000004 0x00000005
+ 0x00000004 0x00000009 0x0000000d 0x0000059f
+ 0x00000000 0x00000003 0x00000003 0x00000003
+ 0x00000003 0x00000001 0x0000000b 0x000000c8
+ 0x00000003 0x00000007 0x00000004 0x0000000f
+ 0x00000002 0x00000000 0x00000000 0x00000002
+ 0x00000000 0x00000000 0x00000083 0xa06204ae
+ 0x007dc010 0x00000000 0x00000000 0x00000000
+ 0x00000000 0x00000000 0x00000000 0x00000000>;
+ };
+
+ emc-table@380000 {
+ reg = <380000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = <380000>;
+ nvidia,emc-registers = <0x00000017 0x0000004b
+ 0x00000012 0x00000006 0x00000004 0x00000005
+ 0x00000003 0x0000000c 0x00000006 0x00000006
+ 0x00000003 0x00000001 0x00000004 0x00000005
+ 0x00000004 0x00000009 0x0000000d 0x00000b5f
+ 0x00000000 0x00000003 0x00000003 0x00000006
+ 0x00000006 0x00000001 0x00000011 0x000000c8
+ 0x00000003 0x0000000e 0x00000007 0x0000000f
+ 0x00000002 0x00000000 0x00000000 0x00000002
+ 0x00000000 0x00000000 0x00000083 0xe044048b
+ 0x007d8010 0x00000000 0x00000000 0x00000000
+ 0x00000000 0x00000000 0x00000000 0x00000000>;
+ };
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */
+ dr_mode = "otg";
+ };
+
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000400 {
+ status = "okay";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio 170 1>; /* gpio PV2, active low */
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+
+ lid {
+ label = "Lid";
+ gpios = <&gpio 23 0>; /* gpio PC7 */
+ linux,input-type = <5>; /* EV_SW */
+ linux,code = <0>; /* SW_LID */
+ debounce-interval = <1>;
+ gpio-key,wakeup;
+ };
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-seaboard",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Seaboard";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1R", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
+ };
+};
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra20.dtsi"
+
+/ {
+ model = "Compulab TrimSlice board";
+ compatible = "compulab,trimslice", "nvidia,tegra20";
+
+ memory {
+ reg = <0x00000000 0x40000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ata {
+ nvidia,pins = "ata";
+ nvidia,function = "ide";
+ };
+ atb {
+ nvidia,pins = "atb", "gma";
+ nvidia,function = "sdio4";
+ };
+ atc {
+ nvidia,pins = "atc", "gmb";
+ nvidia,function = "nand";
+ };
+ atd {
+ nvidia,pins = "atd", "ate", "gme", "pta";
+ nvidia,function = "gmi";
+ };
+ cdev1 {
+ nvidia,pins = "cdev1";
+ nvidia,function = "plla_out";
+ };
+ cdev2 {
+ nvidia,pins = "cdev2";
+ nvidia,function = "pllp_out4";
+ };
+ crtp {
+ nvidia,pins = "crtp";
+ nvidia,function = "crt";
+ };
+ csus {
+ nvidia,pins = "csus";
+ nvidia,function = "vi_sensor_clk";
+ };
+ dap1 {
+ nvidia,pins = "dap1";
+ nvidia,function = "dap1";
+ };
+ dap2 {
+ nvidia,pins = "dap2";
+ nvidia,function = "dap2";
+ };
+ dap3 {
+ nvidia,pins = "dap3";
+ nvidia,function = "dap3";
+ };
+ dap4 {
+ nvidia,pins = "dap4";
+ nvidia,function = "dap4";
+ };
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "i2c2";
+ };
+ dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+ nvidia,function = "vi";
+ };
+ dtf {
+ nvidia,pins = "dtf";
+ nvidia,function = "i2c3";
+ };
+ gmc {
+ nvidia,pins = "gmc", "gmd";
+ nvidia,function = "sflash";
+ };
+ gpu {
+ nvidia,pins = "gpu";
+ nvidia,function = "uarta";
+ };
+ gpu7 {
+ nvidia,pins = "gpu7";
+ nvidia,function = "rtck";
+ };
+ gpv {
+ nvidia,pins = "gpv", "slxa", "slxk";
+ nvidia,function = "pcie";
+ };
+ hdint {
+ nvidia,pins = "hdint";
+ nvidia,function = "hdmi";
+ };
+ i2cp {
+ nvidia,pins = "i2cp";
+ nvidia,function = "i2cp";
+ };
+ irrx {
+ nvidia,pins = "irrx", "irtx";
+ nvidia,function = "uartb";
+ };
+ kbca {
+ nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+ "kbce", "kbcf";
+ nvidia,function = "kbc";
+ };
+ lcsn {
+ nvidia,pins = "lcsn", "ld0", "ld1", "ld2",
+ "ld3", "ld4", "ld5", "ld6", "ld7",
+ "ld8", "ld9", "ld10", "ld11", "ld12",
+ "ld13", "ld14", "ld15", "ld16", "ld17",
+ "ldc", "ldi", "lhp0", "lhp1", "lhp2",
+ "lhs", "lm0", "lm1", "lpp", "lpw0",
+ "lpw1", "lpw2", "lsc0", "lsc1", "lsck",
+ "lsda", "lsdi", "lspi", "lvp0", "lvp1",
+ "lvs";
+ nvidia,function = "displaya";
+ };
+ owc {
+ nvidia,pins = "owc", "uac";
+ nvidia,function = "rsvd2";
+ };
+ pmc {
+ nvidia,pins = "pmc";
+ nvidia,function = "pwr_on";
+ };
+ rm {
+ nvidia,pins = "rm";
+ nvidia,function = "i2c1";
+ };
+ sdb {
+ nvidia,pins = "sdb", "sdc", "sdd";
+ nvidia,function = "pwm";
+ };
+ sdio1 {
+ nvidia,pins = "sdio1";
+ nvidia,function = "sdio1";
+ };
+ slxc {
+ nvidia,pins = "slxc", "slxd";
+ nvidia,function = "sdio3";
+ };
+ spdi {
+ nvidia,pins = "spdi", "spdo";
+ nvidia,function = "spdif";
+ };
+ spia {
+ nvidia,pins = "spia", "spib", "spic";
+ nvidia,function = "spi2";
+ };
+ spid {
+ nvidia,pins = "spid", "spie", "spif";
+ nvidia,function = "spi1";
+ };
+ spig {
+ nvidia,pins = "spig", "spih";
+ nvidia,function = "spi2_alt";
+ };
+ uaa {
+ nvidia,pins = "uaa", "uab", "uda";
+ nvidia,function = "ulpi";
+ };
+ uad {
+ nvidia,pins = "uad";
+ nvidia,function = "irda";
+ };
+ uca {
+ nvidia,pins = "uca", "ucb";
+ nvidia,function = "uartc";
+ };
+ conf_ata {
+ nvidia,pins = "ata", "atc", "atd", "ate",
+ "crtp", "dap2", "dap3", "dap4", "dta",
+ "dtb", "dtc", "dtd", "dte", "gmb",
+ "gme", "i2cp", "pta", "slxc", "slxd",
+ "spdi", "spdo", "uda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ };
+ conf_atb {
+ nvidia,pins = "atb", "cdev1", "cdev2", "dap1",
+ "gma", "gmc", "gmd", "gpu", "gpu7",
+ "gpv", "sdio1", "slxa", "slxk", "uac";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ conf_ck32 {
+ nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+ "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+ nvidia,pull = <0>;
+ };
+ conf_csus {
+ nvidia,pins = "csus", "spia", "spib",
+ "spid", "spif";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ };
+ conf_ddc {
+ nvidia,pins = "ddc", "dtf", "rm", "sdc", "sdd";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ conf_hdint {
+ nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+ "lpw1", "lsc1", "lsck", "lsda", "lsdi",
+ "lvp0", "pmc";
+ nvidia,tristate = <1>;
+ };
+ conf_irrx {
+ nvidia,pins = "irrx", "irtx", "kbca", "kbcb",
+ "kbcc", "kbcd", "kbce", "kbcf", "owc",
+ "spic", "spie", "spig", "spih", "uaa",
+ "uab", "uad", "uca", "ucb";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ };
+ conf_lc {
+ nvidia,pins = "lc", "ls";
+ nvidia,pull = <2>;
+ };
+ conf_ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldi", "lhp0",
+ "lhp1", "lhp2", "lhs", "lm0", "lpp",
+ "lpw0", "lpw2", "lsc0", "lspi", "lvp1",
+ "lvs", "sdb";
+ nvidia,tristate = <0>;
+ };
+ conf_ld17_0 {
+ nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+ "ld23_22";
+ nvidia,pull = <1>;
+ };
+ };
+ };
+
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006000 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ codec: codec@1a {
+ compatible = "ti,tlv320aic23";
+ reg = <0x1a>;
+ };
+
+ rtc@56 {
+ compatible = "emmicro,em3027";
+ reg = <0x56>;
+ };
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ };
+
+ usb@c5004000 {
+ nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000000 {
+ status = "okay";
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ cd-gpios = <&gpio 121 0>; /* gpio PP1 */
+ wp-gpios = <&gpio 122 0>; /* gpio PP2 */
+ bus-width = <4>;
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-trimslice";
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&codec>;
+ };
+};
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra20.dtsi"
+
+/ {
+ model = "NVIDIA Tegra2 Ventana evaluation board";
+ compatible = "nvidia,ventana", "nvidia,tegra20";
+
+ memory {
+ reg = <0x00000000 0x40000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ata {
+ nvidia,pins = "ata";
+ nvidia,function = "ide";
+ };
+ atb {
+ nvidia,pins = "atb", "gma", "gme";
+ nvidia,function = "sdio4";
+ };
+ atc {
+ nvidia,pins = "atc";
+ nvidia,function = "nand";
+ };
+ atd {
+ nvidia,pins = "atd", "ate", "gmb", "spia",
+ "spib", "spic";
+ nvidia,function = "gmi";
+ };
+ cdev1 {
+ nvidia,pins = "cdev1";
+ nvidia,function = "plla_out";
+ };
+ cdev2 {
+ nvidia,pins = "cdev2";
+ nvidia,function = "pllp_out4";
+ };
+ crtp {
+ nvidia,pins = "crtp", "lm1";
+ nvidia,function = "crt";
+ };
+ csus {
+ nvidia,pins = "csus";
+ nvidia,function = "vi_sensor_clk";
+ };
+ dap1 {
+ nvidia,pins = "dap1";
+ nvidia,function = "dap1";
+ };
+ dap2 {
+ nvidia,pins = "dap2";
+ nvidia,function = "dap2";
+ };
+ dap3 {
+ nvidia,pins = "dap3";
+ nvidia,function = "dap3";
+ };
+ dap4 {
+ nvidia,pins = "dap4";
+ nvidia,function = "dap4";
+ };
+ ddc {
+ nvidia,pins = "ddc", "owc", "spdi", "spdo",
+ "uac";
+ nvidia,function = "rsvd2";
+ };
+ dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+ nvidia,function = "vi";
+ };
+ dtf {
+ nvidia,pins = "dtf";
+ nvidia,function = "i2c3";
+ };
+ gmc {
+ nvidia,pins = "gmc";
+ nvidia,function = "uartd";
+ };
+ gmd {
+ nvidia,pins = "gmd";
+ nvidia,function = "sflash";
+ };
+ gpu {
+ nvidia,pins = "gpu";
+ nvidia,function = "pwm";
+ };
+ gpu7 {
+ nvidia,pins = "gpu7";
+ nvidia,function = "rtck";
+ };
+ gpv {
+ nvidia,pins = "gpv", "slxa", "slxk";
+ nvidia,function = "pcie";
+ };
+ hdint {
+ nvidia,pins = "hdint", "pta";
+ nvidia,function = "hdmi";
+ };
+ i2cp {
+ nvidia,pins = "i2cp";
+ nvidia,function = "i2cp";
+ };
+ irrx {
+ nvidia,pins = "irrx", "irtx";
+ nvidia,function = "uartb";
+ };
+ kbca {
+ nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+ "kbce", "kbcf";
+ nvidia,function = "kbc";
+ };
+ lcsn {
+ nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
+ "lsdi", "lvp0";
+ nvidia,function = "rsvd4";
+ };
+ ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldi", "lhp0",
+ "lhp1", "lhp2", "lhs", "lpp", "lpw0",
+ "lpw2", "lsc0", "lsc1", "lsck", "lsda",
+ "lspi", "lvp1", "lvs";
+ nvidia,function = "displaya";
+ };
+ pmc {
+ nvidia,pins = "pmc";
+ nvidia,function = "pwr_on";
+ };
+ rm {
+ nvidia,pins = "rm";
+ nvidia,function = "i2c1";
+ };
+ sdb {
+ nvidia,pins = "sdb", "sdc", "sdd", "slxc";
+ nvidia,function = "sdio3";
+ };
+ sdio1 {
+ nvidia,pins = "sdio1";
+ nvidia,function = "sdio1";
+ };
+ slxd {
+ nvidia,pins = "slxd";
+ nvidia,function = "spdif";
+ };
+ spid {
+ nvidia,pins = "spid", "spie", "spif";
+ nvidia,function = "spi1";
+ };
+ spig {
+ nvidia,pins = "spig", "spih";
+ nvidia,function = "spi2_alt";
+ };
+ uaa {
+ nvidia,pins = "uaa", "uab", "uda";
+ nvidia,function = "ulpi";
+ };
+ uad {
+ nvidia,pins = "uad";
+ nvidia,function = "irda";
+ };
+ uca {
+ nvidia,pins = "uca", "ucb";
+ nvidia,function = "uartc";
+ };
+ conf_ata {
+ nvidia,pins = "ata", "atb", "atc", "atd",
+ "cdev1", "cdev2", "dap1", "dap2",
+ "dap4", "ddc", "dtf", "gma", "gmc",
+ "gme", "gpu", "gpu7", "i2cp", "irrx",
+ "irtx", "pta", "rm", "sdc", "sdd",
+ "slxc", "slxd", "slxk", "spdi", "spdo",
+ "uac", "uad", "uca", "ucb", "uda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ conf_ate {
+ nvidia,pins = "ate", "csus", "dap3", "gmd",
+ "gpv", "owc", "spia", "spib", "spic",
+ "spid", "spie", "spig";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ };
+ conf_ck32 {
+ nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+ "pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+ nvidia,pull = <0>;
+ };
+ conf_crtp {
+ nvidia,pins = "crtp", "gmb", "slxa", "spih";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ };
+ conf_dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ };
+ conf_dte {
+ nvidia,pins = "dte", "spif";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ };
+ conf_hdint {
+ nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+ "lpw1", "lsck", "lsda", "lsdi", "lvp0";
+ nvidia,tristate = <1>;
+ };
+ conf_kbca {
+ nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+ "kbce", "kbcf", "sdio1", "uaa", "uab";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ conf_lc {
+ nvidia,pins = "lc", "ls";
+ nvidia,pull = <2>;
+ };
+ conf_ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldi", "lhp0",
+ "lhp1", "lhp2", "lhs", "lm0", "lpp",
+ "lpw0", "lpw2", "lsc0", "lsc1", "lspi",
+ "lvp1", "lvs", "pmc", "sdb";
+ nvidia,tristate = <0>;
+ };
+ conf_ld17_0 {
+ nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+ "ld23_22";
+ nvidia,pull = <1>;
+ };
+ };
+ };
+
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006300 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ wm8903: wm8903@1a {
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <187 0x04>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+
+ /* ALS and proximity sensor */
+ isl29018@44 {
+ compatible = "isil,isl29018";
+ reg = <0x44>;
+ interrupt-parent = <&gpio>;
+ interrupts = <202 0x04>; /*gpio PZ2 */
+ };
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ };
+
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000400 {
+ status = "okay";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-ventana",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Ventana";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /* gpio PX0 */
+ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+ };
+};
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra20.dtsi"
+
+/ {
+ model = "NVIDIA Tegra2 Whistler evaluation board";
+ compatible = "nvidia,whistler", "nvidia,tegra20";
+
+ memory {
+ reg = <0x00000000 0x20000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ata {
+ nvidia,pins = "ata", "atb", "ate", "gma", "gmb",
+ "gmc", "gmd", "gpu";
+ nvidia,function = "gmi";
+ };
+ atc {
+ nvidia,pins = "atc", "atd";
+ nvidia,function = "sdio4";
+ };
+ cdev1 {
+ nvidia,pins = "cdev1";
+ nvidia,function = "plla_out";
+ };
+ cdev2 {
+ nvidia,pins = "cdev2";
+ nvidia,function = "osc";
+ };
+ crtp {
+ nvidia,pins = "crtp";
+ nvidia,function = "crt";
+ };
+ csus {
+ nvidia,pins = "csus";
+ nvidia,function = "vi_sensor_clk";
+ };
+ dap1 {
+ nvidia,pins = "dap1";
+ nvidia,function = "dap1";
+ };
+ dap2 {
+ nvidia,pins = "dap2";
+ nvidia,function = "dap2";
+ };
+ dap3 {
+ nvidia,pins = "dap3";
+ nvidia,function = "dap3";
+ };
+ dap4 {
+ nvidia,pins = "dap4";
+ nvidia,function = "dap4";
+ };
+ ddc {
+ nvidia,pins = "ddc";
+ nvidia,function = "i2c2";
+ };
+ dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd";
+ nvidia,function = "vi";
+ };
+ dte {
+ nvidia,pins = "dte";
+ nvidia,function = "rsvd1";
+ };
+ dtf {
+ nvidia,pins = "dtf";
+ nvidia,function = "i2c3";
+ };
+ gme {
+ nvidia,pins = "gme";
+ nvidia,function = "dap5";
+ };
+ gpu7 {
+ nvidia,pins = "gpu7";
+ nvidia,function = "rtck";
+ };
+ gpv {
+ nvidia,pins = "gpv";
+ nvidia,function = "pcie";
+ };
+ hdint {
+ nvidia,pins = "hdint", "pta";
+ nvidia,function = "hdmi";
+ };
+ i2cp {
+ nvidia,pins = "i2cp";
+ nvidia,function = "i2cp";
+ };
+ irrx {
+ nvidia,pins = "irrx", "irtx";
+ nvidia,function = "uartb";
+ };
+ kbca {
+ nvidia,pins = "kbca", "kbcc", "kbce", "kbcf";
+ nvidia,function = "kbc";
+ };
+ kbcb {
+ nvidia,pins = "kbcb", "kbcd";
+ nvidia,function = "sdio2";
+ };
+ lcsn {
+ nvidia,pins = "lcsn", "lsck", "lsda", "lsdi",
+ "spia", "spib", "spic";
+ nvidia,function = "spi3";
+ };
+ ld0 {
+ nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+ "ld5", "ld6", "ld7", "ld8", "ld9",
+ "ld10", "ld11", "ld12", "ld13", "ld14",
+ "ld15", "ld16", "ld17", "ldc", "ldi",
+ "lhp0", "lhp1", "lhp2", "lhs", "lm0",
+ "lm1", "lpp", "lpw0", "lpw1", "lpw2",
+ "lsc0", "lsc1", "lspi", "lvp0", "lvp1",
+ "lvs";
+ nvidia,function = "displaya";
+ };
+ owc {
+ nvidia,pins = "owc", "uac";
+ nvidia,function = "owr";
+ };
+ pmc {
+ nvidia,pins = "pmc";
+ nvidia,function = "pwr_on";
+ };
+ rm {
+ nvidia,pins = "rm";
+ nvidia,function = "i2c1";
+ };
+ sdb {
+ nvidia,pins = "sdb", "sdc", "sdd", "slxa",
+ "slxc", "slxd", "slxk";
+ nvidia,function = "sdio3";
+ };
+ sdio1 {
+ nvidia,pins = "sdio1";
+ nvidia,function = "sdio1";
+ };
+ spdi {
+ nvidia,pins = "spdi", "spdo";
+ nvidia,function = "rsvd2";
+ };
+ spid {
+ nvidia,pins = "spid", "spie", "spig", "spih";
+ nvidia,function = "spi2_alt";
+ };
+ spif {
+ nvidia,pins = "spif";
+ nvidia,function = "spi2";
+ };
+ uaa {
+ nvidia,pins = "uaa", "uab";
+ nvidia,function = "uarta";
+ };
+ uad {
+ nvidia,pins = "uad";
+ nvidia,function = "irda";
+ };
+ uca {
+ nvidia,pins = "uca", "ucb";
+ nvidia,function = "uartc";
+ };
+ uda {
+ nvidia,pins = "uda";
+ nvidia,function = "spi1";
+ };
+ conf_ata {
+ nvidia,pins = "ata", "atb", "atc", "ddc", "gma",
+ "gmb", "gmc", "gmd", "irrx", "irtx",
+ "kbca", "kbcb", "kbcc", "kbcd", "kbce",
+ "kbcf", "sdc", "sdd", "spie", "spig",
+ "spih", "uaa", "uab", "uad", "uca",
+ "ucb";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ conf_atd {
+ nvidia,pins = "atd", "ate", "cdev1", "csus",
+ "dap1", "dap2", "dap3", "dap4", "dte",
+ "dtf", "gpu", "gpu7", "gpv", "i2cp",
+ "rm", "sdio1", "slxa", "slxc", "slxd",
+ "slxk", "spdi", "spdo", "uac", "uda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ conf_cdev2 {
+ nvidia,pins = "cdev2", "spia", "spib";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ };
+ conf_ck32 {
+ nvidia,pins = "ck32", "ddrc", "lc", "pmca",
+ "pmcb", "pmcc", "pmcd", "xm2c",
+ "xm2d";
+ nvidia,pull = <0>;
+ };
+ conf_crtp {
+ nvidia,pins = "crtp";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ };
+ conf_dta {
+ nvidia,pins = "dta", "dtb", "dtc", "dtd",
+ "spid", "spif";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ };
+ conf_gme {
+ nvidia,pins = "gme", "owc", "pta", "spic";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ };
+ conf_ld17_0 {
+ nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+ "ld23_22";
+ nvidia,pull = <1>;
+ };
+ conf_ls {
+ nvidia,pins = "ls", "pmce";
+ nvidia,pull = <2>;
+ };
+ drive_dap1 {
+ nvidia,pins = "drive_dap1";
+ nvidia,high-speed-mode = <0>;
+ nvidia,schmitt = <1>;
+ nvidia,low-power-mode = <0>;
+ nvidia,pull-down-strength = <0>;
+ nvidia,pull-up-strength = <0>;
+ nvidia,slew-rate-rising = <0>;
+ nvidia,slew-rate-falling = <0>;
+ };
+ };
+ };
+
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006000 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ codec: codec@1a {
+ compatible = "wlf,wm8753";
+ reg = <0x1a>;
+ };
+
+ tca6416: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ nvidia,vbus-gpio = <&tca6416 0 0>; /* GPIO_PMU0 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ nvidia,vbus-gpio = <&tca6416 1 0>; /* GPIO_PMU1 */
+ };
+
+ sdhci@c8000400 {
+ status = "okay";
+ wp-gpios = <&gpio 173 0>; /* gpio PV5 */
+ bus-width = <8>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8753-whistler",
+ "nvidia,tegra-audio-wm8753";
+ nvidia,model = "NVIDIA Tegra Whistler";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "LOUT1",
+ "Headphone Jack", "ROUT1",
+ "MIC2", "Mic Jack",
+ "MIC2N", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&codec>;
+ };
+};
reg = <0x7000e400 0x400>;
};
- mc {
+ memory-controller@0x7000f000 {
compatible = "nvidia,tegra20-mc";
reg = <0x7000f000 0x024
0x7000f03c 0x3c4>;
0x58000000 0x02000000>; /* GART aperture */
};
- emc {
+ memory-controller@0x7000f400 {
compatible = "nvidia,tegra20-emc";
reg = <0x7000f400 0x200>;
#address-cells = <1>;
--- /dev/null
+/dts-v1/;
+
+/include/ "tegra30.dtsi"
+
+/ {
+ model = "NVIDIA Tegra30 Cardhu evaluation board";
+ compatible = "nvidia,cardhu", "nvidia,tegra30";
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ sdmmc1_clk_pz0 {
+ nvidia,pins = "sdmmc1_clk_pz0";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ sdmmc1_cmd_pz1 {
+ nvidia,pins = "sdmmc1_cmd_pz1",
+ "sdmmc1_dat0_py7",
+ "sdmmc1_dat1_py6",
+ "sdmmc1_dat2_py5",
+ "sdmmc1_dat3_py4";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ sdmmc4_clk_pcc4 {
+ nvidia,pins = "sdmmc4_clk_pcc4",
+ "sdmmc4_rst_n_pcc3";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ sdmmc4_dat0_paa0 {
+ nvidia,pins = "sdmmc4_dat0_paa0",
+ "sdmmc4_dat1_paa1",
+ "sdmmc4_dat2_paa2",
+ "sdmmc4_dat3_paa3",
+ "sdmmc4_dat4_paa4",
+ "sdmmc4_dat5_paa5",
+ "sdmmc4_dat6_paa6",
+ "sdmmc4_dat7_paa7";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ };
+ dap2_fs_pa2 {
+ nvidia,pins = "dap2_fs_pa2",
+ "dap2_sclk_pa3",
+ "dap2_din_pa4",
+ "dap2_dout_pa5";
+ nvidia,function = "i2s1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ };
+ };
+ };
+
+ serial@70006000 {
+ status = "okay";
+ clock-frequency = <408000000>;
+ };
+
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ i2c@7000c400 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ i2c@7000c500 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ /* ALS and Proximity sensor */
+ isl29028@44 {
+ compatible = "isil,isl29028";
+ reg = <0x44>;
+ interrupt-parent = <&gpio>;
+ interrupts = <88 0x04>; /*gpio PL0 */
+ };
+ };
+
+ i2c@7000c700 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ wm8903: wm8903@1a {
+ compatible = "wlf,wm8903";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <179 0x04>; /* gpio PW3 */
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ micdet-cfg = <0>;
+ micdet-delay = <100>;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+
+ tps62361 {
+ compatible = "ti,tps62361";
+ reg = <0x60>;
+
+ regulator-name = "tps62361-vout";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ti,vsel0-state-high;
+ ti,vsel1-state-high;
+ };
+ };
+
+ ahub {
+ i2s@70080400 {
+ status = "okay";
+ };
+ };
+
+ sdhci@78000000 {
+ status = "okay";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 155 0>; /* gpio PT3 */
+ power-gpios = <&gpio 31 0>; /* gpio PD7 */
+ bus-width = <4>;
+ };
+
+ sdhci@78000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-cardhu",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Cardhu";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ };
+};
reg = <0x7000e400 0x400>;
};
- mc {
+ memory-controller {
compatible = "nvidia,tegra30-mc";
reg = <0x7000f000 0x010
0x7000f03c 0x1b4
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_BLK_DEV_BSG is not set
CONFIG_PARTITION_ADVANCED=y
CONFIG_ARCH_LPC32XX=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
CONFIG_PREEMPT=y
CONFIG_AEABI=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_MUSEUM_IDS=y
+CONFIG_MTD_NAND_SLC_LPC32XX=y
+CONFIG_MTD_NAND_MLC_LPC32XX=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=1
CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_EEPROM_AT24=y
CONFIG_EEPROM_AT25=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
# CONFIG_NET_VENDOR_STMICRO is not set
CONFIG_SMSC_PHY=y
# CONFIG_WLAN is not set
+CONFIG_INPUT_MATRIXKMAP=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=240
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320
CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_LPC32XX=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_LPC32XX=y
+CONFIG_SERIO_LIBPS2=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_HS_LPC32XX=y
+CONFIG_SERIAL_OF_PLATFORM=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_SPI=y
CONFIG_SPI_PL022=y
CONFIG_GPIO_SYSFS=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_DS620=y
+CONFIG_SENSORS_MAX6639=y
CONFIG_WATCHDOG=y
CONFIG_PNX4008_WATCHDOG=y
CONFIG_FB=y
CONFIG_MMC_ARMMMCI=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_PCA9532=y
+CONFIG_LEDS_PCA9532_GPIO=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_RTC_DRV_PCF8563=y
CONFIG_RTC_DRV_LPC32XX=y
CONFIG_DMADEVICES=y
-CONFIG_AMBA_PL08X=y
CONFIG_STAGING=y
-CONFIG_IIO=y
CONFIG_LPC32XX_ADC=y
+CONFIG_MAX517=y
+CONFIG_IIO=y
CONFIG_EXT2_FS=y
CONFIG_AUTOFS4_FS=y
CONFIG_MSDOS_FS=y
CONFIG_JFFS2_FS_WBUF_VERIFY=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_ROOT_NFS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=y
# Keep dtb files sorted alphabetically for each SoC
# sam9260
+dtb-$(CONFIG_MACH_AT91SAM_DT) += aks-cdu.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb
+dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9260.dtb
# sam9263
select ARCH_MX25
select COMMON_CLK
select CPU_ARM926T
+ select HAVE_CAN_FLEXCAN if CAN
select ARCH_MXC_IOMUX_V3
select MXC_AVIC
select HAVE_EPIT
select MXC_AVIC
select SMP_ON_UP if SMP
+ select HAVE_CAN_FLEXCAN if CAN
config SOC_IMX5
select CPU_V7
select SOC_IMX5
select ARCH_MX5
select ARCH_MX53
+ select HAVE_CAN_FLEXCAN if CAN
if ARCH_IMX_V4_V5
select COMMON_CLK
select CPU_V7
select HAVE_ARM_SCU
+ select HAVE_CAN_FLEXCAN if CAN
select HAVE_IMX_GPC
select HAVE_IMX_MMDC
select HAVE_IMX_SRC
esai, gpt_ipg, gpt_ipg_per, gpu2d_core, gpu3d_core, hdmi_iahb,
hdmi_isfr, i2c1, i2c2, i2c3, iim, enfc, ipu1, ipu1_di0, ipu1_di1, ipu2,
ipu2_di0, ldb_di0, ldb_di1, ipu2_di1, hsi_tx, mlb, mmdc_ch0_axi,
- mmdc_ch1_axi, ocram, openvg_axi, pcie_axi, pwm1, pwm2, pwm3, pwm4,
+ mmdc_ch1_axi, ocram, openvg_axi, pcie_axi, pwm1, pwm2, pwm3, pwm4, per1_bch,
gpmi_bch_apb, gpmi_bch, gpmi_io, gpmi_apb, sata, sdma, spba, ssi1,
ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
clk[ahb] = imx_clk_busy_divider("ahb", "periph", base + 0x14, 10, 3, base + 0x48, 1);
/* name parent_name reg shift */
- clk[apbh_dma] = imx_clk_gate2("apbh_dma", "ahb", base + 0x68, 4);
+ clk[apbh_dma] = imx_clk_gate2("apbh_dma", "usdhc3", base + 0x68, 4);
clk[asrc] = imx_clk_gate2("asrc", "asrc_podf", base + 0x68, 6);
clk[can1_ipg] = imx_clk_gate2("can1_ipg", "ipg", base + 0x68, 14);
clk[can1_serial] = imx_clk_gate2("can1_serial", "can_root", base + 0x68, 16);
clk[ocram] = imx_clk_gate2("ocram", "ahb", base + 0x74, 28);
clk[openvg_axi] = imx_clk_gate2("openvg_axi", "axi", base + 0x74, 30);
clk[pcie_axi] = imx_clk_gate2("pcie_axi", "pcie_axi_sel", base + 0x78, 0);
+ clk[per1_bch] = imx_clk_gate2("per1_bch", "usdhc3", base + 0x78, 12);
clk[pwm1] = imx_clk_gate2("pwm1", "ipg_per", base + 0x78, 16);
clk[pwm2] = imx_clk_gate2("pwm2", "ipg_per", base + 0x78, 18);
clk[pwm3] = imx_clk_gate2("pwm3", "ipg_per", base + 0x78, 20);
clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0");
clk_register_clkdev(clk[twd], NULL, "smp_twd");
clk_register_clkdev(clk[usboh3], NULL, "usboh3");
+ clk_register_clkdev(clk[apbh_dma], NULL, "110000.dma-apbh");
+ clk_register_clkdev(clk[per1_bch], "per1_bch", "112000.gpmi-nand");
+ clk_register_clkdev(clk[gpmi_bch_apb], "gpmi_bch_apb", "112000.gpmi-nand");
+ clk_register_clkdev(clk[gpmi_bch], "gpmi_bch", "112000.gpmi-nand");
+ clk_register_clkdev(clk[gpmi_apb], "gpmi_apb", "112000.gpmi-nand");
+ clk_register_clkdev(clk[gpmi_io], "gpmi_io", "112000.gpmi-nand");
clk_register_clkdev(clk[uart_serial], "per", "2020000.serial");
clk_register_clkdev(clk[uart_ipg], "ipg", "2020000.serial");
clk_register_clkdev(clk[uart_serial], "per", "21e8000.serial");
+++ /dev/null
-if ARCH_LPC32XX
-
-menu "Individual UART enable selections"
-
-config ARCH_LPC32XX_UART3_SELECT
- bool "Add support for standard UART3"
- help
- Adds support for standard UART 3 when the 8250 serial support
- is enabled.
-
-config ARCH_LPC32XX_UART4_SELECT
- bool "Add support for standard UART4"
- help
- Adds support for standard UART 4 when the 8250 serial support
- is enabled.
-
-config ARCH_LPC32XX_UART5_SELECT
- bool "Add support for standard UART5"
- default y
- help
- Adds support for standard UART 5 when the 8250 serial support
- is enabled.
-
-config ARCH_LPC32XX_UART6_SELECT
- bool "Add support for standard UART6"
- help
- Adds support for standard UART 6 when the 8250 serial support
- is enabled.
-
-endmenu
-
-endif
params_phys-y := 0x80000100
initrd_phys-y := 0x82000000
+dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
.parent = &clk_hclk,
.enable = local_onoff_enable,
.enable_reg = LPC32XX_CLKPWR_NAND_CLK_CTRL,
- .enable_mask = LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN,
+ .enable_mask = LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN |
+ LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
.get_rate = local_return_parent_rate,
};
+static struct clk clk_nand_mlc = {
+ .parent = &clk_hclk,
+ .enable = local_onoff_enable,
+ .enable_reg = LPC32XX_CLKPWR_NAND_CLK_CTRL,
+ .enable_mask = LPC32XX_CLKPWR_NANDCLK_MLCCLK_EN |
+ LPC32XX_CLKPWR_NANDCLK_DMA_INT |
+ LPC32XX_CLKPWR_NANDCLK_INTSEL_MLC,
+ .get_rate = local_return_parent_rate,
+};
+
static struct clk clk_i2s0 = {
.parent = &clk_hclk,
.enable = local_onoff_enable,
.parent = &clk_hclk,
.enable = local_onoff_enable,
.enable_reg = LPC32XX_CLKPWR_I2S_CLK_CTRL,
- .enable_mask = LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN,
+ .enable_mask = LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN |
+ LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA,
.get_rate = local_return_parent_rate,
};
CLKDEV_INIT("31020300.i2c", NULL, &clk_i2c2),
CLKDEV_INIT("dev:ssp0", NULL, &clk_ssp0),
CLKDEV_INIT("dev:ssp1", NULL, &clk_ssp1),
- CLKDEV_INIT("lpc32xx_keys.0", NULL, &clk_kscan),
- CLKDEV_INIT("lpc32xx-nand.0", "nand_ck", &clk_nand),
+ CLKDEV_INIT("40050000.key", NULL, &clk_kscan),
+ CLKDEV_INIT("20020000.flash", NULL, &clk_nand),
+ CLKDEV_INIT("200a8000.flash", NULL, &clk_nand_mlc),
CLKDEV_INIT("40048000.adc", NULL, &clk_adc),
CLKDEV_INIT(NULL, "i2s0_ck", &clk_i2s0),
CLKDEV_INIT(NULL, "i2s1_ck", &clk_i2s1),
#include "gpio-lpc32xx.h"
-#define ARCH_NR_GPIOS (LPC32XX_GPO_P3_GRP + LPC32XX_GPO_P3_MAX)
-
#endif /* __MACH_GPIO_H */
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/amba/pl022.h>
+#include <linux/amba/pl08x.h>
+#include <linux/amba/mmci.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/clk.h>
-#include <linux/amba/pl08x.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
/*
* Mapped GPIOLIB GPIOs
*/
-#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
-#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
-#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
+#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define MMC_PWR_ENABLE_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 5)
+#define MMC_CD_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 1)
+#define MMC_WP_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 0)
/*
* AMBA LCD controller
/*
* AMBA SSP (SPI)
*/
-static void phy3250_spi_cs_set(u32 control)
-{
- gpio_set_value(SPI0_CS_GPIO, (int) control);
-}
-
-static struct pl022_config_chip spi0_chip_info = {
- .com_mode = INTERRUPT_TRANSFER,
- .iface = SSP_INTERFACE_MOTOROLA_SPI,
- .hierarchy = SSP_MASTER,
- .slave_tx_disable = 0,
- .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
- .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
- .ctrl_len = SSP_BITS_8,
- .wait_state = SSP_MWIRE_WAIT_ZERO,
- .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
- .cs_control = phy3250_spi_cs_set,
-};
-
static struct pl022_ssp_controller lpc32xx_ssp0_data = {
.bus_id = 0,
.num_chipselect = 1,
.enable_dma = 0,
};
-/* AT25 driver registration */
-static int __init phy3250_spi_board_register(void)
+static struct pl08x_channel_data pl08x_slave_channels[] = {
+ {
+ .bus_id = "nand-slc",
+ .min_signal = 1, /* SLC NAND Flash */
+ .max_signal = 1,
+ .periph_buses = PL08X_AHB1,
+ },
+ {
+ .bus_id = "nand-mlc",
+ .min_signal = 12, /* MLC NAND Flash */
+ .max_signal = 12,
+ .periph_buses = PL08X_AHB1,
+ },
+};
+
+/* NOTE: These will change, according to RMK */
+static int pl08x_get_signal(struct pl08x_dma_chan *ch)
+{
+ return ch->cd->min_signal;
+}
+
+static void pl08x_put_signal(struct pl08x_dma_chan *ch)
{
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
- static struct spi_board_info info[] = {
- {
- .modalias = "spidev",
- .max_speed_hz = 5000000,
- .bus_num = 0,
- .chip_select = 0,
- .controller_data = &spi0_chip_info,
- },
- };
-
-#else
- static struct spi_eeprom eeprom = {
- .name = "at25256a",
- .byte_len = 0x8000,
- .page_size = 64,
- .flags = EE_ADDR2,
- };
-
- static struct spi_board_info info[] = {
- {
- .modalias = "at25",
- .max_speed_hz = 5000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = SPI_MODE_0,
- .platform_data = &eeprom,
- .controller_data = &spi0_chip_info,
- },
- };
-#endif
- return spi_register_board_info(info, ARRAY_SIZE(info));
}
-arch_initcall(phy3250_spi_board_register);
static struct pl08x_platform_data pl08x_pd = {
+ .slave_channels = &pl08x_slave_channels[0],
+ .num_slave_channels = ARRAY_SIZE(pl08x_slave_channels),
+ .get_signal = pl08x_get_signal,
+ .put_signal = pl08x_put_signal,
+ .lli_buses = PL08X_AHB1,
+ .mem_buses = PL08X_AHB1,
+};
+
+static int mmc_handle_ios(struct device *dev, struct mmc_ios *ios)
+{
+ /* Only on and off are supported */
+ if (ios->power_mode == MMC_POWER_OFF)
+ gpio_set_value(MMC_PWR_ENABLE_GPIO, 0);
+ else
+ gpio_set_value(MMC_PWR_ENABLE_GPIO, 1);
+ return 0;
+}
+
+static struct mmci_platform_data lpc32xx_mmci_data = {
+ .ocr_mask = MMC_VDD_30_31 | MMC_VDD_31_32 |
+ MMC_VDD_32_33 | MMC_VDD_33_34,
+ .ios_handler = mmc_handle_ios,
+ .dma_filter = NULL,
+ /* No DMA for now since AMBA PL080 dmaengine driver only does scatter
+ * gather, and the MMCI driver doesn't do it this way */
};
static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
+ OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd",
+ &lpc32xx_mmci_data),
{ }
};
{
u32 tmp;
- /* Setup SLC NAND controller muxing */
- __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
- LPC32XX_CLKPWR_NAND_CLK_CTRL);
-
/* Setup LCD muxing to RGB565 */
tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
__raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
- /* Disable IrDA pulsing support on UART6 */
- tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
- tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
- __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
- /* Enable DMA for I2S1 channel */
- tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
- tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
- __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
-
lpc32xx_serial_init();
- /*
- * AMBA peripheral clocks need to be enabled prior to AMBA device
- * detection or a data fault will occur, so enable the clocks
- * here.
- */
- tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
- __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
- LPC32XX_CLKPWR_LCDCLK_CTRL);
-
- tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
- __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
- LPC32XX_CLKPWR_SSP_CLK_CTRL);
-
- tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL);
- __raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN),
- LPC32XX_CLKPWR_DMA_CLK_CTRL);
+ tmp = __raw_readl(LPC32XX_CLKPWR_MS_CTRL);
+ tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_EN |
+ LPC32XX_CLKPWR_MSCARD_MSDIO_PU_EN;
+ __raw_writel(tmp, LPC32XX_CLKPWR_MS_CTRL);
/* Test clock needed for UDA1380 initial init */
__raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
lpc32xx_auxdata_lookup, NULL);
/* Register GPIOs used on this board */
- if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
- printk(KERN_ERR "Error requesting gpio %u",
- SPI0_CS_GPIO);
- else if (gpio_direction_output(SPI0_CS_GPIO, 1))
- printk(KERN_ERR "Error setting gpio %u to output",
- SPI0_CS_GPIO);
+ if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en"))
+ pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO);
+ else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1))
+ pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO);
}
static char const *lpc32xx_dt_compat[] __initdata = {
#define LPC32XX_SUART_FIFO_SIZE 64
-/* Standard 8250/16550 compatible serial ports */
-static struct plat_serial8250_port serial_std_platform_data[] = {
-#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
- {
- .membase = io_p2v(LPC32XX_UART5_BASE),
- .mapbase = LPC32XX_UART5_BASE,
- .irq = IRQ_LPC32XX_UART_IIR5,
- .uartclk = LPC32XX_MAIN_OSC_FREQ,
- .regshift = 2,
- .iotype = UPIO_MEM32,
- .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
- UPF_SKIP_TEST,
- },
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
- {
- .membase = io_p2v(LPC32XX_UART3_BASE),
- .mapbase = LPC32XX_UART3_BASE,
- .irq = IRQ_LPC32XX_UART_IIR3,
- .uartclk = LPC32XX_MAIN_OSC_FREQ,
- .regshift = 2,
- .iotype = UPIO_MEM32,
- .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
- UPF_SKIP_TEST,
- },
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
- {
- .membase = io_p2v(LPC32XX_UART4_BASE),
- .mapbase = LPC32XX_UART4_BASE,
- .irq = IRQ_LPC32XX_UART_IIR4,
- .uartclk = LPC32XX_MAIN_OSC_FREQ,
- .regshift = 2,
- .iotype = UPIO_MEM32,
- .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
- UPF_SKIP_TEST,
- },
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
- {
- .membase = io_p2v(LPC32XX_UART6_BASE),
- .mapbase = LPC32XX_UART6_BASE,
- .irq = IRQ_LPC32XX_UART_IIR6,
- .uartclk = LPC32XX_MAIN_OSC_FREQ,
- .regshift = 2,
- .iotype = UPIO_MEM32,
- .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART |
- UPF_SKIP_TEST,
- },
-#endif
- { },
-};
-
struct uartinit {
char *uart_ck_name;
u32 ck_mode_mask;
};
static struct uartinit uartinit_data[] __initdata = {
-#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT
{
.uart_ck_name = "uart5_ck",
.ck_mode_mask =
.pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL,
.mapbase = LPC32XX_UART5_BASE,
},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT
{
.uart_ck_name = "uart3_ck",
.ck_mode_mask =
.pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL,
.mapbase = LPC32XX_UART3_BASE,
},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT
{
.uart_ck_name = "uart4_ck",
.ck_mode_mask =
.pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL,
.mapbase = LPC32XX_UART4_BASE,
},
-#endif
-#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT
{
.uart_ck_name = "uart6_ck",
.ck_mode_mask =
.pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL,
.mapbase = LPC32XX_UART6_BASE,
},
-#endif
-};
-
-static struct platform_device serial_std_platform_device = {
- .name = "serial8250",
- .id = 0,
- .dev = {
- .platform_data = serial_std_platform_data,
- },
-};
-
-static struct platform_device *lpc32xx_serial_devs[] __initdata = {
- &serial_std_platform_device,
};
void __init lpc32xx_serial_init(void)
clk = clk_get(NULL, uartinit_data[i].uart_ck_name);
if (!IS_ERR(clk)) {
clk_enable(clk);
- serial_std_platform_data[i].uartclk =
- clk_get_rate(clk);
}
- /* Fall back on main osc rate if clock rate return fails */
- if (serial_std_platform_data[i].uartclk == 0)
- serial_std_platform_data[i].uartclk =
- LPC32XX_MAIN_OSC_FREQ;
-
/* Setup UART clock modes for all UARTs, disable autoclock */
clkmodes |= uartinit_data[i].ck_mode_mask;
__raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE);
for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) {
/* Force a flush of the RX FIFOs to work around a HW bug */
- puart = serial_std_platform_data[i].mapbase;
+ puart = uartinit_data[i].mapbase;
__raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart));
__raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart));
j = LPC32XX_SUART_FIFO_SIZE;
__raw_writel(0, LPC32XX_UART_IIR_FCR(puart));
}
+ /* Disable IrDA pulsing support on UART6 */
+ tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
+ tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
+ __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
+
/* Disable UART5->USB transparent mode or USB won't work */
tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
tmp &= ~LPC32XX_UART_U5_ROUTE_TO_USB;
__raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
- platform_add_devices(lpc32xx_serial_devs,
- ARRAY_SIZE(lpc32xx_serial_devs));
}
bool
select ARM_AMBA
select CPU_ARM926T
+ select HAVE_CAN_FLEXCAN if CAN
select HAVE_PWM
select PINCTRL_IMX28
*/
#include <mach/mx23.h>
#include <mach/devices-common.h>
-#include <mach/mxsfb.h>
+#include <linux/mxsfb.h>
#include <linux/amba/bus.h>
static inline int mx23_add_duart(void)
*/
#include <mach/mx28.h>
#include <mach/devices-common.h>
-#include <mach/mxsfb.h>
+#include <linux/mxsfb.h>
#include <linux/amba/bus.h>
static inline int mx28_add_duart(void)
#include <mach/mx23.h>
#include <mach/mx28.h>
#include <mach/devices-common.h>
-#include <mach/mxsfb.h>
+#include <linux/mxsfb.h>
#ifdef CONFIG_SOC_IMX23
struct platform_device *__init mx23_add_mxsfb(
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef __MACH_FB_H
-#define __MACH_FB_H
-
-#include <linux/fb.h>
-
-#define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */
-#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
-#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
-#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
-
-#define FB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6)
-#define FB_SYNC_DOTCLK_FAILING_ACT (1 << 7) /* failing/negtive edge sampling */
-
-struct mxsfb_platform_data {
- struct fb_videomode *mode_list;
- unsigned mode_count;
-
- unsigned default_bpp;
-
- unsigned dotclk_delay; /* refer manual HW_LCDIF_VDCTRL4 register */
- unsigned ld_intf_width; /* refer STMLCDIF_* macros */
-
- unsigned fb_size; /* Size of the video memory. If zero a
- * default will be used
- */
- unsigned long fb_phys; /* physical address for the video memory. If
- * zero the framebuffer memory will be dynamically
- * allocated. If specified,fb_size must also be specified.
- * fb_phys must be unused by Linux.
- */
-};
-
-#endif /* __MACH_FB_H */
#include <linux/init.h>
#include <linux/init.h>
#include <linux/irqdomain.h>
+#include <linux/mxsfb.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
+static struct fb_videomode mx23evk_video_modes[] = {
+ {
+ .name = "Samsung-LMS430HF02",
+ .refresh = 60,
+ .xres = 480,
+ .yres = 272,
+ .pixclock = 108096, /* picosecond (9.2 MHz) */
+ .left_margin = 15,
+ .right_margin = 8,
+ .upper_margin = 12,
+ .lower_margin = 4,
+ .hsync_len = 1,
+ .vsync_len = 1,
+ .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT |
+ FB_SYNC_DOTCLK_FAILING_ACT,
+ },
+};
+
+static struct fb_videomode mx28evk_video_modes[] = {
+ {
+ .name = "Seiko-43WVF1G",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 29851, /* picosecond (33.5 MHz) */
+ .left_margin = 89,
+ .right_margin = 164,
+ .upper_margin = 23,
+ .lower_margin = 10,
+ .hsync_len = 10,
+ .vsync_len = 10,
+ .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT |
+ FB_SYNC_DOTCLK_FAILING_ACT,
+ },
+};
+
+static struct mxsfb_platform_data mxsfb_pdata __initdata;
+
+static struct of_dev_auxdata mxs_auxdata_lookup[] __initdata = {
+ OF_DEV_AUXDATA("fsl,imx23-lcdif", 0x80030000, NULL, &mxsfb_pdata),
+ OF_DEV_AUXDATA("fsl,imx28-lcdif", 0x80030000, NULL, &mxsfb_pdata),
+ { /* sentinel */ }
+};
+
static int __init mxs_icoll_add_irq_domain(struct device_node *np,
struct device_node *interrupt_parent)
{
.init = imx28_timer_init,
};
+enum mac_oui {
+ OUI_FSL,
+ OUI_DENX,
+};
+
+static void __init update_fec_mac_prop(enum mac_oui oui)
+{
+ struct device_node *np, *from = NULL;
+ struct property *oldmac, *newmac;
+ const u32 *ocotp = mxs_get_ocotp();
+ u8 *macaddr;
+ u32 val;
+ int i;
+
+ for (i = 0; i < 2; i++) {
+ np = of_find_compatible_node(from, NULL, "fsl,imx28-fec");
+ if (!np)
+ return;
+ from = np;
+
+ newmac = kzalloc(sizeof(*newmac) + 6, GFP_KERNEL);
+ if (!newmac)
+ return;
+ newmac->value = newmac + 1;
+ newmac->length = 6;
+
+ newmac->name = kstrdup("local-mac-address", GFP_KERNEL);
+ if (!newmac->name) {
+ kfree(newmac);
+ return;
+ }
+
+ /*
+ * OCOTP only stores the last 4 octets for each mac address,
+ * so hard-code OUI here.
+ */
+ macaddr = newmac->value;
+ switch (oui) {
+ case OUI_FSL:
+ macaddr[0] = 0x00;
+ macaddr[1] = 0x04;
+ macaddr[2] = 0x9f;
+ break;
+ case OUI_DENX:
+ macaddr[0] = 0xc0;
+ macaddr[1] = 0xe5;
+ macaddr[2] = 0x4e;
+ break;
+ }
+ val = ocotp[i];
+ macaddr[3] = (val >> 16) & 0xff;
+ macaddr[4] = (val >> 8) & 0xff;
+ macaddr[5] = (val >> 0) & 0xff;
+
+ oldmac = of_find_property(np, newmac->name, NULL);
+ if (oldmac)
+ prom_update_property(np, newmac, oldmac);
+ else
+ prom_add_property(np, newmac);
+ }
+}
+
+static void __init imx23_evk_init(void)
+{
+ mxsfb_pdata.mode_list = mx23evk_video_modes;
+ mxsfb_pdata.mode_count = ARRAY_SIZE(mx23evk_video_modes);
+ mxsfb_pdata.default_bpp = 32;
+ mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
+}
+
static void __init imx28_evk_init(void)
{
struct clk *clk;
clk = clk_get_sys("enet_out", NULL);
if (!IS_ERR(clk))
clk_prepare_enable(clk);
+
+ update_fec_mac_prop(OUI_FSL);
+
+ mxsfb_pdata.mode_list = mx28evk_video_modes;
+ mxsfb_pdata.mode_count = ARRAY_SIZE(mx28evk_video_modes);
+ mxsfb_pdata.default_bpp = 32;
+ mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
}
static void __init mxs_machine_init(void)
{
if (of_machine_is_compatible("fsl,imx28-evk"))
imx28_evk_init();
+ else if (of_machine_is_compatible("fsl,imx23-evk"))
+ imx23_evk_init();
of_platform_populate(NULL, of_default_bus_match_table,
- NULL, NULL);
+ mxs_auxdata_lookup, NULL);
}
static const char *imx23_dt_compat[] __initdata = {
"fsl,imx23-evk",
+ "olimex,imx23-olinuxino",
"fsl,imx23",
NULL,
};
static const char *imx28_dt_compat[] __initdata = {
+ "crystalfontz,cfa10036",
"fsl,imx28-evk",
"fsl,imx28",
NULL,
# Object file lists.
-obj-y += clock.o
-
# Cpu revision
obj-$(CONFIG_NOMADIK_8815) += cpu-8815.o
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/amba/bus.h>
+#include <linux/amba/mmci.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/onenand.h>
#include <linux/mtd/partitions.h>
+#include <linux/i2c.h>
#include <linux/io.h>
#include <asm/hardware/vic.h>
#include <asm/sizes.h>
#endif
}
-static AMBA_APB_DEVICE(uart0, "uart0", 0, NOMADIK_UART0_BASE,
- { IRQ_UART0 }, NULL);
+static struct mmci_platform_data mmcsd_plat_data = {
+ .ocr_mask = MMC_VDD_29_30,
+ .f_max = 48000000,
+ .gpio_wp = -1,
+ .gpio_cd = 111,
+ .cd_invert = true,
+ .capabilities = MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA,
+};
-static AMBA_APB_DEVICE(uart1, "uart1", 0, NOMADIK_UART1_BASE,
- { IRQ_UART1 }, NULL);
+static int __init nhk8815_mmcsd_init(void)
+{
+ int ret;
-static struct amba_device *amba_devs[] __initdata = {
- &uart0_device,
- &uart1_device,
-};
+ ret = gpio_request(112, "card detect bias");
+ if (ret)
+ return ret;
+ gpio_direction_output(112, 0);
+ amba_apb_device_add(NULL, "mmci", NOMADIK_SDI_BASE, SZ_4K, IRQ_SDMMC, 0, &mmcsd_plat_data, 0x10180180);
+ return 0;
+}
+module_init(nhk8815_mmcsd_init);
static struct resource nhk8815_eth_resources[] = {
{
.init = nomadik_timer_init,
};
+static struct i2c_board_info __initdata nhk8815_i2c0_devices[] = {
+ {
+ I2C_BOARD_INFO("stw4811", 0x2d),
+ },
+};
+
+static struct i2c_board_info __initdata nhk8815_i2c1_devices[] = {
+ {
+ I2C_BOARD_INFO("camera", 0x10),
+ },
+ {
+ I2C_BOARD_INFO("stw5095", 0x1a),
+ },
+ {
+ I2C_BOARD_INFO("lis3lv02dl", 0x1d),
+ },
+};
+
+static struct i2c_board_info __initdata nhk8815_i2c2_devices[] = {
+ {
+ I2C_BOARD_INFO("stw4811-usb", 0x2d),
+ },
+};
+
static void __init nhk8815_platform_init(void)
{
- int i;
-
cpu8815_platform_init();
nhk8815_onenand_init();
platform_add_devices(nhk8815_platform_devices,
ARRAY_SIZE(nhk8815_platform_devices));
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
- amba_device_register(amba_devs[i], &iomem_resource);
+ amba_apb_device_add(NULL, "uart0", NOMADIK_UART0_BASE, SZ_4K, IRQ_UART0, 0, NULL, 0);
+ amba_apb_device_add(NULL, "uart1", NOMADIK_UART1_BASE, SZ_4K, IRQ_UART1, 0, NULL, 0);
+
+ i2c_register_board_info(0, nhk8815_i2c0_devices,
+ ARRAY_SIZE(nhk8815_i2c0_devices));
+ i2c_register_board_info(1, nhk8815_i2c1_devices,
+ ARRAY_SIZE(nhk8815_i2c1_devices));
+ i2c_register_board_info(2, nhk8815_i2c2_devices,
+ ARRAY_SIZE(nhk8815_i2c2_devices));
}
MACHINE_START(NOMADIK, "NHK8815")
+++ /dev/null
-/*
- * linux/arch/arm/mach-nomadik/clock.c
- *
- * Copyright (C) 2009 Alessandro Rubini
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/clk.h>
-#include <linux/clkdev.h>
-#include "clock.h"
-
-/*
- * The nomadik board uses generic clocks, but the serial pl011 file
- * calls clk_enable(), clk_disable(), clk_get_rate(), so we provide them
- */
-unsigned long clk_get_rate(struct clk *clk)
-{
- return clk->rate;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-/* enable and disable do nothing */
-int clk_enable(struct clk *clk)
-{
- return 0;
-}
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable(struct clk *clk)
-{
-}
-EXPORT_SYMBOL(clk_disable);
-
-static struct clk clk_24 = {
- .rate = 2400000,
-};
-
-static struct clk clk_48 = {
- .rate = 48 * 1000 * 1000,
-};
-
-/*
- * Catch-all default clock to satisfy drivers using the clk API. We don't
- * model the actual hardware clocks yet.
- */
-static struct clk clk_default;
-
-#define CLK(_clk, dev) \
- { \
- .clk = _clk, \
- .dev_id = dev, \
- }
-
-static struct clk_lookup lookups[] = {
- {
- .con_id = "apb_pclk",
- .clk = &clk_default,
- },
- CLK(&clk_24, "mtu0"),
- CLK(&clk_24, "mtu1"),
- CLK(&clk_48, "uart0"),
- CLK(&clk_48, "uart1"),
- CLK(&clk_default, "gpio.0"),
- CLK(&clk_default, "gpio.1"),
- CLK(&clk_default, "gpio.2"),
- CLK(&clk_default, "gpio.3"),
- CLK(&clk_default, "rng"),
-};
-
-int __init clk_init(void)
-{
- clkdev_add_table(lookups, ARRAY_SIZE(lookups));
- return 0;
-}
+++ /dev/null
-
-/*
- * linux/arch/arm/mach-nomadik/clock.h
- *
- * Copyright (C) 2009 Alessandro Rubini
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-struct clk {
- unsigned long rate;
-};
-
-int __init clk_init(void);
#include <linux/amba/bus.h>
#include <linux/platform_device.h>
#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/irq.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_data/clk-nomadik.h>
#include <plat/gpio-nomadik.h>
#include <mach/hardware.h>
#include <asm/cacheflush.h>
#include <asm/hardware/cache-l2x0.h>
-#include "clock.h"
#include "cpu-8815.h"
-#define __MEM_4K_RESOURCE(x) \
- .res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
-
/* The 8815 has 4 GPIO blocks, let's register them immediately */
-
-#define GPIO_RESOURCE(block) \
- { \
- .start = NOMADIK_GPIO##block##_BASE, \
- .end = NOMADIK_GPIO##block##_BASE + SZ_4K - 1, \
- .flags = IORESOURCE_MEM, \
- }, \
- { \
- .start = IRQ_GPIO##block, \
- .end = IRQ_GPIO##block, \
- .flags = IORESOURCE_IRQ, \
- }
-
-#define GPIO_DEVICE(block) \
- { \
- .name = "gpio", \
- .id = block, \
- .num_resources = 2, \
- .resource = &cpu8815_gpio_resources[block * 2], \
- .dev = { \
- .platform_data = &cpu8815_gpio[block], \
- }, \
- }
-
-static struct nmk_gpio_platform_data cpu8815_gpio[] = {
- {
- .name = "GPIO-0-31",
- .first_gpio = 0,
- .first_irq = NOMADIK_GPIO_TO_IRQ(0),
- }, {
- .name = "GPIO-32-63",
- .first_gpio = 32,
- .first_irq = NOMADIK_GPIO_TO_IRQ(32),
- }, {
- .name = "GPIO-64-95",
- .first_gpio = 64,
- .first_irq = NOMADIK_GPIO_TO_IRQ(64),
- }, {
- .name = "GPIO-96-127", /* 124..127 not routed to pin */
- .first_gpio = 96,
- .first_irq = NOMADIK_GPIO_TO_IRQ(96),
- }
+static resource_size_t __initdata cpu8815_gpio_base[] = {
+ NOMADIK_GPIO0_BASE,
+ NOMADIK_GPIO1_BASE,
+ NOMADIK_GPIO2_BASE,
+ NOMADIK_GPIO3_BASE,
};
-static struct resource cpu8815_gpio_resources[] = {
- GPIO_RESOURCE(0),
- GPIO_RESOURCE(1),
- GPIO_RESOURCE(2),
- GPIO_RESOURCE(3),
-};
-
-static struct platform_device cpu8815_platform_gpio[] = {
- GPIO_DEVICE(0),
- GPIO_DEVICE(1),
- GPIO_DEVICE(2),
- GPIO_DEVICE(3),
-};
+static struct platform_device *
+cpu8815_add_gpio(int id, resource_size_t addr, int irq,
+ struct nmk_gpio_platform_data *pdata)
+{
+ struct resource resources[] = {
+ {
+ .start = addr,
+ .end = addr + 127,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = irq,
+ .end = irq,
+ .flags = IORESOURCE_IRQ,
+ }
+ };
+
+ return platform_device_register_resndata(NULL, "gpio", id,
+ resources, ARRAY_SIZE(resources),
+ pdata, sizeof(*pdata));
+}
-static AMBA_APB_DEVICE(cpu8815_amba_rng, "rng", 0, NOMADIK_RNG_BASE, { }, NULL);
+void cpu8815_add_gpios(resource_size_t *base, int num, int irq,
+ struct nmk_gpio_platform_data *pdata)
+{
+ int first = 0;
+ int i;
-static struct platform_device *platform_devs[] __initdata = {
- cpu8815_platform_gpio + 0,
- cpu8815_platform_gpio + 1,
- cpu8815_platform_gpio + 2,
- cpu8815_platform_gpio + 3,
-};
+ for (i = 0; i < num; i++, first += 32, irq++) {
+ pdata->first_gpio = first;
+ pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first);
+ pdata->num_gpio = 32;
-static struct amba_device *amba_devs[] __initdata = {
- &cpu8815_amba_rng_device
-};
+ cpu8815_add_gpio(i, base[i], irq, pdata);
+ }
+}
static int __init cpu8815_init(void)
{
- int i;
-
- platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
- amba_device_register(amba_devs[i], &iomem_resource);
+ struct nmk_gpio_platform_data pdata = {
+ /* No custom data yet */
+ };
+
+ cpu8815_add_gpios(cpu8815_gpio_base, ARRAY_SIZE(cpu8815_gpio_base),
+ IRQ_GPIO0, &pdata);
+ amba_apb_device_add(NULL, "rng", NOMADIK_RNG_BASE, SZ_4K, 0, 0, NULL, 0);
+ amba_apb_device_add(NULL, "rtc-pl031", NOMADIK_RTC_BASE, SZ_4K, IRQ_RTC_RTT, 0, NULL, 0);
return 0;
}
arch_initcall(cpu8815_init);
* Init clocks here so that they are available for system timer
* initialization.
*/
- clk_init();
+ nomadik_clk_init();
}
/*
#include <linux/i2c-gpio.h>
#include <linux/platform_device.h>
#include <plat/gpio-nomadik.h>
+#include <plat/pincfg.h>
/*
* There are two busses in the 8815NHK.
* use bit-bang through GPIO by now, to keep things simple
*/
+/* I2C0 connected to the STw4811 power management chip */
static struct i2c_gpio_platform_data nhk8815_i2c_data0 = {
/* keep defaults for timeouts; pins are push-pull bidirectional */
.scl_pin = 62,
.sda_pin = 63,
};
+/* I2C1 connected to various sensors */
static struct i2c_gpio_platform_data nhk8815_i2c_data1 = {
/* keep defaults for timeouts; pins are push-pull bidirectional */
.scl_pin = 53,
.sda_pin = 54,
};
-/* first bus: GPIO XX and YY */
+/* I2C2 connected to the USB portions of the STw4811 only */
+static struct i2c_gpio_platform_data nhk8815_i2c_data2 = {
+ /* keep defaults for timeouts; pins are push-pull bidirectional */
+ .scl_pin = 73,
+ .sda_pin = 74,
+};
+
static struct platform_device nhk8815_i2c_dev0 = {
.name = "i2c-gpio",
.id = 0,
.platform_data = &nhk8815_i2c_data0,
},
};
-/* second bus: GPIO XX and YY */
+
static struct platform_device nhk8815_i2c_dev1 = {
.name = "i2c-gpio",
.id = 1,
},
};
+static struct platform_device nhk8815_i2c_dev2 = {
+ .name = "i2c-gpio",
+ .id = 2,
+ .dev = {
+ .platform_data = &nhk8815_i2c_data2,
+ },
+};
+
+static pin_cfg_t cpu8815_pins_i2c[] = {
+ PIN_CFG_INPUT(62, GPIO, PULLUP),
+ PIN_CFG_INPUT(63, GPIO, PULLUP),
+ PIN_CFG_INPUT(53, GPIO, PULLUP),
+ PIN_CFG_INPUT(54, GPIO, PULLUP),
+ PIN_CFG_INPUT(73, GPIO, PULLUP),
+ PIN_CFG_INPUT(74, GPIO, PULLUP),
+};
+
static int __init nhk8815_i2c_init(void)
{
- nmk_gpio_set_mode(nhk8815_i2c_data0.scl_pin, NMK_GPIO_ALT_GPIO);
- nmk_gpio_set_mode(nhk8815_i2c_data0.sda_pin, NMK_GPIO_ALT_GPIO);
+ nmk_config_pins(cpu8815_pins_i2c, ARRAY_SIZE(cpu8815_pins_i2c));
platform_device_register(&nhk8815_i2c_dev0);
-
- nmk_gpio_set_mode(nhk8815_i2c_data1.scl_pin, NMK_GPIO_ALT_GPIO);
- nmk_gpio_set_mode(nhk8815_i2c_data1.sda_pin, NMK_GPIO_ALT_GPIO);
platform_device_register(&nhk8815_i2c_dev1);
+ platform_device_register(&nhk8815_i2c_dev2);
return 0;
}
{
platform_device_unregister(&nhk8815_i2c_dev0);
platform_device_unregister(&nhk8815_i2c_dev1);
+ platform_device_unregister(&nhk8815_i2c_dev2);
return;
}
#include <mach/hardware.h>
-#define IRQ_VIC_START 0 /* first VIC interrupt is 0 */
+#define IRQ_VIC_START 1 /* first VIC interrupt is 1 */
/*
* Interrupt numbers generic for all Nomadik Chip cuts
*/
-#define IRQ_WATCHDOG 0
-#define IRQ_SOFTINT 1
-#define IRQ_CRYPTO 2
-#define IRQ_OWM 3
-#define IRQ_MTU0 4
-#define IRQ_MTU1 5
-#define IRQ_GPIO0 6
-#define IRQ_GPIO1 7
-#define IRQ_GPIO2 8
-#define IRQ_GPIO3 9
-#define IRQ_RTC_RTT 10
-#define IRQ_SSP 11
-#define IRQ_UART0 12
-#define IRQ_DMA1 13
-#define IRQ_CLCD_MDIF 14
-#define IRQ_DMA0 15
-#define IRQ_PWRFAIL 16
-#define IRQ_UART1 17
-#define IRQ_FIRDA 18
-#define IRQ_MSP0 19
-#define IRQ_I2C0 20
-#define IRQ_I2C1 21
-#define IRQ_SDMMC 22
-#define IRQ_USBOTG 23
-#define IRQ_SVA_IT0 24
-#define IRQ_SVA_IT1 25
-#define IRQ_SAA_IT0 26
-#define IRQ_SAA_IT1 27
-#define IRQ_UART2 28
-#define IRQ_MSP2 31
-#define IRQ_L2CC 48
-#define IRQ_HPI 49
-#define IRQ_SKE 50
-#define IRQ_KP 51
-#define IRQ_MEMST 54
-#define IRQ_SGA_IT 58
-#define IRQ_USBM 60
-#define IRQ_MSP1 62
+#define IRQ_WATCHDOG 1
+#define IRQ_SOFTINT 2
+#define IRQ_CRYPTO 3
+#define IRQ_OWM 4
+#define IRQ_MTU0 5
+#define IRQ_MTU1 6
+#define IRQ_GPIO0 7
+#define IRQ_GPIO1 8
+#define IRQ_GPIO2 9
+#define IRQ_GPIO3 10
+#define IRQ_RTC_RTT 11
+#define IRQ_SSP 12
+#define IRQ_UART0 13
+#define IRQ_DMA1 14
+#define IRQ_CLCD_MDIF 15
+#define IRQ_DMA0 16
+#define IRQ_PWRFAIL 17
+#define IRQ_UART1 18
+#define IRQ_FIRDA 19
+#define IRQ_MSP0 20
+#define IRQ_I2C0 21
+#define IRQ_I2C1 22
+#define IRQ_SDMMC 23
+#define IRQ_USBOTG 24
+#define IRQ_SVA_IT0 25
+#define IRQ_SVA_IT1 26
+#define IRQ_SAA_IT0 27
+#define IRQ_SAA_IT1 28
+#define IRQ_UART2 29
+#define IRQ_MSP2 30
+#define IRQ_L2CC 49
+#define IRQ_HPI 50
+#define IRQ_SKE 51
+#define IRQ_KP 52
+#define IRQ_MEMST 55
+#define IRQ_SGA_IT 59
+#define IRQ_USBM 61
+#define IRQ_MSP1 63
-#define NOMADIK_SOC_NR_IRQS 64
+#define NOMADIK_GPIO_OFFSET (IRQ_VIC_START+64)
/* After chip-specific IRQ numbers we have the GPIO ones */
#define NOMADIK_NR_GPIO 128 /* last 4 not wired to pins */
-#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + NOMADIK_SOC_NR_IRQS)
-#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - NOMADIK_SOC_NR_IRQS)
+#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + NOMADIK_GPIO_OFFSET)
+#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - NOMADIK_GPIO_OFFSET)
#define NR_IRQS NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO)
/* Following two are used by entry_macro.S, to access our dual-vic */
#define VIC_REG_IRQSR1 0x20
#endif /* __ASM_ARCH_IRQS_H */
-
char *oh_name = "wd_timer2";
char *dev_name = "omap_wdt";
- if (!cpu_class_is_omap2())
+ if (!cpu_class_is_omap2() || of_have_populated_dt())
return 0;
oh = omap_hwmod_lookup(oh_name);
config MACH_HARMONY
bool "Harmony board"
depends on ARCH_TEGRA_2x_SOC
- select MACH_HAS_SND_SOC_TEGRA_WM8903 if SND_SOC
help
Support for nVidia Harmony development platform
bool "Kaen board"
depends on ARCH_TEGRA_2x_SOC
select MACH_SEABOARD
- select MACH_HAS_SND_SOC_TEGRA_WM8903 if SND_SOC
help
Support for the Kaen version of Seaboard
config MACH_SEABOARD
bool "Seaboard board"
depends on ARCH_TEGRA_2x_SOC
- select MACH_HAS_SND_SOC_TEGRA_WM8903 if SND_SOC
help
Support for nVidia Seaboard development platform. It will
also be included for some of the derivative boards that
params_phys-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00000100
initrd_phys-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00800000
-dtb-$(CONFIG_MACH_HARMONY) += tegra-harmony.dtb
-dtb-$(CONFIG_MACH_PAZ00) += tegra-paz00.dtb
-dtb-$(CONFIG_MACH_SEABOARD) += tegra-seaboard.dtb
-dtb-$(CONFIG_MACH_TRIMSLICE) += tegra-trimslice.dtb
-dtb-$(CONFIG_MACH_VENTANA) += tegra-ventana.dtb
-dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra-cardhu.dtb
+dtb-$(CONFIG_MACH_HARMONY) += tegra20-harmony.dtb
+dtb-$(CONFIG_MACH_PAZ00) += tegra20-paz00.dtb
+dtb-$(CONFIG_MACH_SEABOARD) += tegra20-seaboard.dtb
+dtb-$(CONFIG_MACH_TRIMSLICE) += tegra20-trimslice.dtb
+dtb-$(CONFIG_MACH_VENTANA) += tegra20-ventana.dtb
+dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += tegra20-whistler.dtb
+dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra30-cardhu.dtb
#include <linux/cpuidle.h>
#include <linux/hrtimer.h>
-#include <mach/iomap.h>
+#include <asm/proc-fns.h>
-extern void tegra_cpu_wfi(void);
+#include <mach/iomap.h>
static int tegra_idle_enter_lp3(struct cpuidle_device *dev,
struct cpuidle_driver *drv, int index);
enter = ktime_get();
- tegra_cpu_wfi();
+ cpu_do_idle();
exit = ktime_sub(ktime_get(), enter);
us = ktime_to_us(exit);
movw \reg, #:lower16:\val
movt \reg, #:upper16:\val
.endm
-
-/*
- * tegra_cpu_wfi
- *
- * puts current CPU in clock-gated wfi using the flow controller
- *
- * corrupts r0-r3
- * must be called with MMU on
- */
-
-ENTRY(tegra_cpu_wfi)
- cpu_id r0
- cpu_to_halt_reg r1, r0
- cpu_to_csr_reg r2, r0
- mov32 r0, TEGRA_FLOW_CTRL_VIRT
- mov r3, #FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG
- str r3, [r0, r2] @ clear event & interrupt status
- mov r3, #FLOW_CTRL_WAIT_FOR_INTERRUPT | FLOW_CTRL_JTAG_RESUME
- str r3, [r0, r1] @ put flow controller in wait irq mode
- dsb
- wfi
- mov r3, #0
- str r3, [r0, r1] @ clear flow controller halt status
- mov r3, #FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG
- str r3, [r0, r2] @ clear event & interrupt status
- dsb
- mov pc, lr
-ENDPROC(tegra_cpu_wfi)
-
return 0;
}
-static int __devexit tegra_ahb_remove(struct platform_device *pdev)
-{
- return 0;
-}
-
static const struct of_device_id tegra_ahb_of_match[] __devinitconst = {
{ .compatible = "nvidia,tegra30-ahb", },
{ .compatible = "nvidia,tegra20-ahb", },
static struct platform_driver tegra_ahb_driver = {
.probe = tegra_ahb_probe,
- .remove = __devexit_p(tegra_ahb_remove),
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
obj-$(CONFIG_COMMON_CLK) += clk.o clk-fixed-rate.o clk-gate.o \
clk-mux.o clk-divider.o clk-fixed-factor.o
# SoCs specific
+obj-$(CONFIG_ARCH_NOMADIK) += clk-nomadik.o
obj-$(CONFIG_ARCH_MXS) += mxs/
obj-$(CONFIG_PLAT_SPEAR) += spear/
--- /dev/null
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk-provider.h>
+
+/*
+ * The Nomadik clock tree is described in the STN8815A12 DB V4.2
+ * reference manual for the chip, page 94 ff.
+ */
+
+void __init nomadik_clk_init(void)
+{
+ struct clk *clk;
+
+ clk = clk_register_fixed_rate(NULL, "apb_pclk", NULL, CLK_IS_ROOT, 0);
+ clk_register_clkdev(clk, "apb_pclk", NULL);
+ clk_register_clkdev(clk, NULL, "gpio.0");
+ clk_register_clkdev(clk, NULL, "gpio.1");
+ clk_register_clkdev(clk, NULL, "gpio.2");
+ clk_register_clkdev(clk, NULL, "gpio.3");
+ clk_register_clkdev(clk, NULL, "rng");
+
+ /*
+ * The 2.4 MHz TIMCLK reference clock is active at boot time, this is
+ * actually the MXTALCLK @19.2 MHz divided by 8. This clock is used
+ * by the timers and watchdog. See page 105 ff.
+ */
+ clk = clk_register_fixed_rate(NULL, "TIMCLK", NULL, CLK_IS_ROOT,
+ 2400000);
+ clk_register_clkdev(clk, NULL, "mtu0");
+ clk_register_clkdev(clk, NULL, "mtu1");
+
+ /*
+ * At boot time, PLL2 is set to generate a set of fixed clocks,
+ * one of them is CLK48, the 48 MHz clock, routed to the UART, MMC/SD
+ * I2C, IrDA, USB and SSP blocks.
+ */
+ clk = clk_register_fixed_rate(NULL, "CLK48", NULL, CLK_IS_ROOT,
+ 48000000);
+ clk_register_clkdev(clk, NULL, "uart0");
+ clk_register_clkdev(clk, NULL, "uart1");
+ clk_register_clkdev(clk, NULL, "mmci");
+ clk_register_clkdev(clk, NULL, "ssp");
+ clk_register_clkdev(clk, NULL, "nmk-i2c.0");
+ clk_register_clkdev(clk, NULL, "nmk-i2c.1");
+}
{
struct tegra_sdhci_platform_data *plat;
struct device_node *np = pdev->dev.of_node;
+ u32 bus_width;
if (!np)
return NULL;
plat->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
plat->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
plat->power_gpio = of_get_named_gpio(np, "power-gpios", 0);
- if (of_find_property(np, "support-8bit", NULL))
+
+ if (of_property_read_u32(np, "bus-width", &bus_width) == 0 &&
+ bus_width == 8)
plat->is_8bit = 1;
return plat;
#include <linux/interrupt.h>
#include <linux/rtc.h>
#include <linux/slab.h>
+#include <linux/of_device.h>
#include <mach/common.h>
#define stmp3xxx_rtc_resume NULL
#endif
+static const struct of_device_id rtc_dt_ids[] = {
+ { .compatible = "fsl,stmp3xxx-rtc", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rtc_dt_ids);
+
static struct platform_driver stmp3xxx_rtcdrv = {
.probe = stmp3xxx_rtc_probe,
.remove = stmp3xxx_rtc_remove,
.driver = {
.name = "stmp3xxx-rtc",
.owner = THIS_MODULE,
+ .of_match_table = rtc_dt_ids,
},
};
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/pinctrl/consumer.h>
+#include <linux/of_device.h>
#include <asm/cacheflush.h>
#endif
};
+/*
+ * This function returns 1 if pdev isn't a device instatiated by dt, 0 if it
+ * could successfully get all information from dt or a negative errno.
+ */
+static int serial_mxs_probe_dt(struct mxs_auart_port *s,
+ struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+
+ if (!np)
+ /* no device tree device */
+ return 1;
+
+ ret = of_alias_get_id(np, "serial");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to get alias id: %d\n", ret);
+ return ret;
+ }
+ s->port.line = ret;
+
+ return 0;
+}
+
static int __devinit mxs_auart_probe(struct platform_device *pdev)
{
struct mxs_auart_port *s;
goto out;
}
+ ret = serial_mxs_probe_dt(s, pdev);
+ if (ret > 0)
+ s->port.line = pdev->id < 0 ? 0 : pdev->id;
+ else if (ret < 0)
+ goto out_free;
+
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
if (IS_ERR(pinctrl)) {
ret = PTR_ERR(pinctrl);
s->port.membase = ioremap(r->start, resource_size(r));
s->port.ops = &mxs_auart_ops;
s->port.iotype = UPIO_MEM;
- s->port.line = pdev->id < 0 ? 0 : pdev->id;
s->port.fifosize = 16;
s->port.uartclk = clk_get_rate(s->clk);
s->port.type = PORT_IMX;
platform_set_drvdata(pdev, s);
- auart_port[pdev->id] = s;
+ auart_port[s->port.line] = s;
mxs_auart_reset(&s->port);
return 0;
}
+static struct of_device_id mxs_auart_dt_ids[] = {
+ { .compatible = "fsl,imx23-auart", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids);
+
static struct platform_driver mxs_auart_driver = {
.probe = mxs_auart_probe,
.remove = __devexit_p(mxs_auart_remove),
.driver = {
.name = "mxs-auart",
.owner = THIS_MODULE,
+ .of_match_table = mxs_auart_dt_ids,
},
};
module_exit(mxs_auart_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Freescale MXS application uart driver");
+MODULE_ALIAS("platform:mxs-auart");
#include <linux/module.h>
#include <linux/kernel.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/pinctrl/consumer.h>
-#include <mach/mxsfb.h>
+#include <linux/mxsfb.h>
#define REG_SET 4
#define REG_CLR 8
}
}
+static struct platform_device_id mxsfb_devtype[] = {
+ {
+ .name = "imx23-fb",
+ .driver_data = MXSFB_V3,
+ }, {
+ .name = "imx28-fb",
+ .driver_data = MXSFB_V4,
+ }, {
+ /* sentinel */
+ }
+};
+MODULE_DEVICE_TABLE(platform, mxsfb_devtype);
+
+static const struct of_device_id mxsfb_dt_ids[] = {
+ { .compatible = "fsl,imx23-lcdif", .data = &mxsfb_devtype[0], },
+ { .compatible = "fsl,imx28-lcdif", .data = &mxsfb_devtype[1], },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxsfb_dt_ids);
+
static int __devinit mxsfb_probe(struct platform_device *pdev)
{
+ const struct of_device_id *of_id =
+ of_match_device(mxsfb_dt_ids, &pdev->dev);
struct mxsfb_platform_data *pdata = pdev->dev.platform_data;
struct resource *res;
struct mxsfb_info *host;
struct fb_info *fb_info;
struct fb_modelist *modelist;
struct pinctrl *pinctrl;
+ int panel_enable;
+ enum of_gpio_flags flags;
int i, ret;
+ if (of_id)
+ pdev->id_entry = of_id->data;
+
if (!pdata) {
dev_err(&pdev->dev, "No platformdata. Giving up\n");
return -ENODEV;
goto error_getclock;
}
+ panel_enable = of_get_named_gpio_flags(pdev->dev.of_node,
+ "panel-enable-gpios", 0, &flags);
+ if (gpio_is_valid(panel_enable)) {
+ unsigned long f = GPIOF_OUT_INIT_HIGH;
+ if (flags == OF_GPIO_ACTIVE_LOW)
+ f = GPIOF_OUT_INIT_LOW;
+ ret = devm_gpio_request_one(&pdev->dev, panel_enable,
+ f, "panel-enable");
+ if (ret) {
+ dev_err(&pdev->dev,
+ "failed to request gpio %d: %d\n",
+ panel_enable, ret);
+ goto error_panel_enable;
+ }
+ }
+
fb_info->pseudo_palette = kmalloc(sizeof(u32) * 16, GFP_KERNEL);
if (!fb_info->pseudo_palette) {
ret = -ENOMEM;
error_init_fb:
kfree(fb_info->pseudo_palette);
error_pseudo_pallette:
+error_panel_enable:
clk_put(host->clk);
error_getclock:
error_getpin:
writel(CTRL_RUN, host->base + LCDC_CTRL + REG_CLR);
}
-static struct platform_device_id mxsfb_devtype[] = {
- {
- .name = "imx23-fb",
- .driver_data = MXSFB_V3,
- }, {
- .name = "imx28-fb",
- .driver_data = MXSFB_V4,
- }, {
- /* sentinel */
- }
-};
-MODULE_DEVICE_TABLE(platform, mxsfb_devtype);
-
static struct platform_driver mxsfb_driver = {
.probe = mxsfb_probe,
.remove = __devexit_p(mxsfb_remove),
.id_table = mxsfb_devtype,
.driver = {
.name = DRIVER_NAME,
+ .of_match_table = mxsfb_dt_ids,
},
};
#define omap_wdt_resume NULL
#endif
+static const struct of_device_id omap_wdt_of_match[] = {
+ { .compatible = "ti,omap3-wdt", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, omap_wdt_of_match);
+
static struct platform_driver omap_wdt_driver = {
.probe = omap_wdt_probe,
.remove = __devexit_p(omap_wdt_remove),
.driver = {
.owner = THIS_MODULE,
.name = "omap_wdt",
+ .of_match_table = omap_wdt_of_match,
},
};
--- /dev/null
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __LINUX_MXSFB_H
+#define __LINUX_MXSFB_H
+
+#include <linux/fb.h>
+
+#define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */
+#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
+#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
+#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
+
+#define FB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6)
+#define FB_SYNC_DOTCLK_FAILING_ACT (1 << 7) /* failing/negtive edge sampling */
+
+struct mxsfb_platform_data {
+ struct fb_videomode *mode_list;
+ unsigned mode_count;
+
+ unsigned default_bpp;
+
+ unsigned dotclk_delay; /* refer manual HW_LCDIF_VDCTRL4 register */
+ unsigned ld_intf_width; /* refer STMLCDIF_* macros */
+
+ unsigned fb_size; /* Size of the video memory. If zero a
+ * default will be used
+ */
+ unsigned long fb_phys; /* physical address for the video memory. If
+ * zero the framebuffer memory will be dynamically
+ * allocated. If specified,fb_size must also be specified.
+ * fb_phys must be unused by Linux.
+ */
+};
+
+#endif /* __LINUX_MXSFB_H */
--- /dev/null
+/* Minimal platform data header */
+void nomadik_clk_init(void);
Say Y or M here if you want to add support for SoC audio on Tegra
boards using the WM8753 codec, such as Whistler.
-config MACH_HAS_SND_SOC_TEGRA_WM8903
- bool
- help
- Machines that use the SND_SOC_TEGRA_WM8903 driver should select
- this config option, in order to allow the user to enable
- SND_SOC_TEGRA_WM8903.
-
config SND_SOC_TEGRA_WM8903
tristate "SoC Audio support for Tegra boards using a WM8903 codec"
depends on SND_SOC_TEGRA && I2C
- depends on MACH_HAS_SND_SOC_TEGRA_WM8903
select SND_SOC_TEGRA20_I2S if ARCH_TEGRA_2x_SOC
select SND_SOC_TEGRA30_I2S if ARCH_TEGRA_3x_SOC
select SND_SOC_WM8903
config SND_SOC_TEGRA_TRIMSLICE
tristate "SoC Audio support for TrimSlice board"
- depends on SND_SOC_TEGRA && MACH_TRIMSLICE && I2C
+ depends on SND_SOC_TEGRA && I2C
select SND_SOC_TEGRA20_I2S if ARCH_TEGRA_2x_SOC
select SND_SOC_TLV320AIC23
help
projects / firefly-linux-kernel-4.4.55.git / commitdiff