USB: Add USB 2.0 to ssb ohci driver
authorHauke Mehrtens <hauke@hauke-m.de>
Wed, 28 Jul 2010 20:11:35 +0000 (22:11 +0200)
committerGreg Kroah-Hartman <gregkh@suse.de>
Tue, 10 Aug 2010 21:35:44 +0000 (14:35 -0700)
This adds USB 2.0 support to ssb ohci driver.
This patch was used in OpenWRT for a long time now.

CC: Steve Brown <sbrown@cortland.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ohci-ssb.c

index 23fd6a886bddb0f25d2279d3da8d11c66e5e61ad..48ee6943bf35af8d463ee4d6f05254a3bbd1da79 100644 (file)
@@ -93,8 +93,11 @@ static void ssb_ohci_detach(struct ssb_device *dev)
 {
        struct usb_hcd *hcd = ssb_get_drvdata(dev);
 
+       if (hcd->driver->shutdown)
+               hcd->driver->shutdown(hcd);
        usb_remove_hcd(hcd);
        iounmap(hcd->regs);
+       release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
        usb_put_hcd(hcd);
        ssb_device_disable(dev, 0);
 }
@@ -106,10 +109,52 @@ static int ssb_ohci_attach(struct ssb_device *dev)
        int err = -ENOMEM;
        u32 tmp, flags = 0;
 
-       if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
-               flags |= SSB_OHCI_TMSLOW_HOSTMODE;
+       if (dma_set_mask(dev->dma_dev, DMA_BIT_MASK(32)) ||
+           dma_set_coherent_mask(dev->dma_dev, DMA_BIT_MASK(32)))
+               return -EOPNOTSUPP;
 
-       ssb_device_enable(dev, flags);
+       if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
+               /* Put the device into host-mode. */
+               flags |= SSB_OHCI_TMSLOW_HOSTMODE;
+               ssb_device_enable(dev, flags);
+       } else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
+               /*
+                * USB 2.0 special considerations:
+                *
+                * In addition to the standard SSB reset sequence, the Host
+                * Control Register must be programmed to bring the USB core
+                * and various phy components out of reset.
+                */
+               ssb_device_enable(dev, 0);
+               ssb_write32(dev, 0x200, 0x7ff);
+
+               /* Change Flush control reg */
+               tmp = ssb_read32(dev, 0x400);
+               tmp &= ~8;
+               ssb_write32(dev, 0x400, tmp);
+               tmp = ssb_read32(dev, 0x400);
+
+               /* Change Shim control reg */
+               tmp = ssb_read32(dev, 0x304);
+               tmp &= ~0x100;
+               ssb_write32(dev, 0x304, tmp);
+               tmp = ssb_read32(dev, 0x304);
+
+               udelay(1);
+
+               /* Work around for 5354 failures */
+               if (dev->id.revision == 2 && dev->bus->chip_id == 0x5354) {
+                       /* Change syn01 reg */
+                       tmp = 0x00fe00fe;
+                       ssb_write32(dev, 0x894, tmp);
+
+                       /* Change syn03 reg */
+                       tmp = ssb_read32(dev, 0x89c);
+                       tmp |= 0x1;
+                       ssb_write32(dev, 0x89c, tmp);
+               }
+       } else
+               ssb_device_enable(dev, 0);
 
        hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
                        dev_name(dev->dev));
@@ -200,6 +245,7 @@ static int ssb_ohci_resume(struct ssb_device *dev)
 static const struct ssb_device_id ssb_ohci_table[] = {
        SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
        SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
+       SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
        SSB_DEVTABLE_END
 };
 MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);