+++ /dev/null
-Embedded Memory Controller
-
-Properties:
-- name : Should be emc
-- #address-cells : Should be 1
-- #size-cells : Should be 0
-- compatible : Should contain "nvidia,tegra20-emc".
-- reg : Offset and length of the register set for the device
-- nvidia,use-ram-code : If present, the sub-nodes will be addressed
- and chosen using the ramcode board selector. If omitted, only one
- set of tables can be present and said tables will be used
- irrespective of ram-code configuration.
-
-Child device nodes describe the memory settings for different configurations and clock rates.
-
-Example:
-
- memory-controller@7000f400 {
- #address-cells = < 1 >;
- #size-cells = < 0 >;
- compatible = "nvidia,tegra20-emc";
- reg = <0x7000f4000 0x200>;
- }
-
-
-Embedded Memory Controller ram-code table
-
-If the emc node has the nvidia,use-ram-code property present, then the
-next level of nodes below the emc table are used to specify which settings
-apply for which ram-code settings.
-
-If the emc node lacks the nvidia,use-ram-code property, this level is omitted
-and the tables are stored directly under the emc node (see below).
-
-Properties:
-
-- name : Should be emc-tables
-- nvidia,ram-code : the binary representation of the ram-code board strappings
- for which this node (and children) are valid.
-
-
-
-Embedded Memory Controller configuration table
-
-This is a table containing the EMC register settings for the various
-operating speeds of the memory controller. They are always located as
-subnodes of the emc controller node.
-
-There are two ways of specifying which tables to use:
-
-* The simplest is if there is just one set of tables in the device tree,
- and they will always be used (based on which frequency is used).
- This is the preferred method, especially when firmware can fill in
- this information based on the specific system information and just
- pass it on to the kernel.
-
-* The slightly more complex one is when more than one memory configuration
- might exist on the system. The Tegra20 platform handles this during
- early boot by selecting one out of possible 4 memory settings based
- on a 2-pin "ram code" bootstrap setting on the board. The values of
- these strappings can be read through a register in the SoC, and thus
- used to select which tables to use.
-
-Properties:
-- name : Should be emc-table
-- compatible : Should contain "nvidia,tegra20-emc-table".
-- reg : either an opaque enumerator to tell different tables apart, or
- the valid frequency for which the table should be used (in kHz).
-- clock-frequency : the clock frequency for the EMC at which this
- table should be used (in kHz).
-- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
- for operation at the 'clock-frequency' setting.
- The order and contents of the registers are:
- RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
- WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
- PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
- TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
- ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
- ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
- CFG_CLKTRIM_1, CFG_CLKTRIM_2
-
- emc-table@166000 {
- reg = <166000>;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = < 166000 >;
- nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 >;
- };
-
- emc-table@333000 {
- reg = <333000>;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = < 333000 >;
- nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- 0 0 0 0 >;
- };
--- /dev/null
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+ and chosen using the ramcode board selector. If omitted, only one
+ set of tables can be present and said tables will be used
+ irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+ memory-controller@7000f400 {
+ #address-cells = < 1 >;
+ #size-cells = < 0 >;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f4000 0x200>;
+ }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+ for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+ and they will always be used (based on which frequency is used).
+ This is the preferred method, especially when firmware can fill in
+ this information based on the specific system information and just
+ pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+ might exist on the system. The Tegra20 platform handles this during
+ early boot by selecting one out of possible 4 memory settings based
+ on a 2-pin "ram code" bootstrap setting on the board. The values of
+ these strappings can be read through a register in the SoC, and thus
+ used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+ the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+ table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+ for operation at the 'clock-frequency' setting.
+ The order and contents of the registers are:
+ RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+ WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+ PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+ TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+ ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+ ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+ CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+ emc-table@166000 {
+ reg = <166000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 166000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+
+ emc-table@333000 {
+ reg = <333000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 333000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+++ /dev/null
-NVIDIA Tegra GPIO controller
-
-Required properties:
-- compatible : "nvidia,tegra<chip>-gpio"
-- reg : Physical base address and length of the controller's registers.
-- interrupts : The interrupt outputs from the controller. For Tegra20,
- there should be 7 interrupts specified, and for Tegra30, there should
- be 8 interrupts specified.
-- #gpio-cells : Should be two. The first cell is the pin number and the
- second cell is used to specify optional parameters:
- - bit 0 specifies polarity (0 for normal, 1 for inverted)
-- gpio-controller : Marks the device node as a GPIO controller.
-- #interrupt-cells : Should be 2.
- The first cell is the GPIO number.
- The second cell is used to specify flags:
- bits[3:0] trigger type and level flags:
- 1 = low-to-high edge triggered.
- 2 = high-to-low edge triggered.
- 4 = active high level-sensitive.
- 8 = active low level-sensitive.
- Valid combinations are 1, 2, 3, 4, 8.
-- interrupt-controller : Marks the device node as an interrupt controller.
-
-Example:
-
-gpio: gpio@6000d000 {
- compatible = "nvidia,tegra20-gpio";
- reg = < 0x6000d000 0x1000 >;
- interrupts = < 0 32 0x04
- 0 33 0x04
- 0 34 0x04
- 0 35 0x04
- 0 55 0x04
- 0 87 0x04
- 0 89 0x04 >;
- #gpio-cells = <2>;
- gpio-controller;
- #interrupt-cells = <2>;
- interrupt-controller;
-};
--- /dev/null
+NVIDIA Tegra GPIO controller
+
+Required properties:
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+ there should be 7 interrupts specified, and for Tegra30, there should
+ be 8 interrupts specified.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+ second cell is used to specify optional parameters:
+ - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+ The first cell is the GPIO number.
+ The second cell is used to specify flags:
+ bits[3:0] trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+ Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+ compatible = "nvidia,tegra20-gpio";
+ reg = < 0x6000d000 0x1000 >;
+ interrupts = < 0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04 >;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+};
--- /dev/null
+* Tegra keyboard controller
+
+Required properties:
+- compatible: "nvidia,tegra20-kbc"
+
+Optional properties, in addition to those specified by the shared
+matrix-keyboard bindings:
+
+- linux,fn-keymap: a second keymap, same specification as the
+ matrix-keyboard-controller spec but to be used when the KEY_FN modifier
+ key is pressed.
+- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
+- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
+- nvidia,ghost-filter: enable ghost filtering for this device
+- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
+
+Example:
+
+keyboard: keyboard {
+ compatible = "nvidia,tegra20-kbc";
+ reg = <0x7000e200 0x100>;
+ nvidia,ghost-filter;
+};
+++ /dev/null
-* Tegra keyboard controller
-
-Required properties:
-- compatible: "nvidia,tegra20-kbc"
-
-Optional properties, in addition to those specified by the shared
-matrix-keyboard bindings:
-
-- linux,fn-keymap: a second keymap, same specification as the
- matrix-keyboard-controller spec but to be used when the KEY_FN modifier
- key is pressed.
-- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
-- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
-- nvidia,ghost-filter: enable ghost filtering for this device
-- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
-
-Example:
-
-keyboard: keyboard {
- compatible = "nvidia,tegra20-kbc";
- reg = <0x7000e200 0x100>;
- nvidia,ghost-filter;
-};
--- /dev/null
+* NVIDIA Tegra Secure Digital Host Controller
+
+This controller on Tegra family SoCs provides an interface for MMC, SD,
+and SDIO types of memory cards.
+
+Required properties:
+- compatible : Should be "nvidia,<chip>-sdhci"
+- reg : Should contain SD/MMC registers location and length
+- interrupts : Should contain SD/MMC interrupt
+- bus-width : Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- cd-gpios : Specify GPIOs for card detection
+- wp-gpios : Specify GPIOs for write protection
+- power-gpios : Specify GPIOs for power control
+
+Example:
+
+sdhci@c8000200 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000200 0x200>;
+ interrupts = <47>;
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 155 0>; /* gpio PT3 */
+ bus-width = <8>;
+};
+++ /dev/null
-* NVIDIA Tegra Secure Digital Host Controller
-
-This controller on Tegra family SoCs provides an interface for MMC, SD,
-and SDIO types of memory cards.
-
-Required properties:
-- compatible : Should be "nvidia,<chip>-sdhci"
-- reg : Should contain SD/MMC registers location and length
-- interrupts : Should contain SD/MMC interrupt
-- bus-width : Number of data lines, can be <1>, <4>, or <8>
-
-Optional properties:
-- cd-gpios : Specify GPIOs for card detection
-- wp-gpios : Specify GPIOs for write protection
-- power-gpios : Specify GPIOs for power control
-
-Example:
-
-sdhci@c8000200 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000200 0x200>;
- interrupts = <47>;
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 155 0>; /* gpio PT3 */
- bus-width = <8>;
-};
+++ /dev/null
-NVIDIA compliant embedded controller
-
-Required properties:
-- compatible : should be "nvidia,nvec".
-- reg : the iomem of the i2c slave controller
-- interrupts : the interrupt line of the i2c slave controller
-- clock-frequency : the frequency of the i2c bus
-- gpios : the gpio used for ec request
-- slave-addr: the i2c address of the slave controller
--- /dev/null
+NVIDIA compliant embedded controller
+
+Required properties:
+- compatible : should be "nvidia,nvec".
+- reg : the iomem of the i2c slave controller
+- interrupts : the interrupt line of the i2c slave controller
+- clock-frequency : the frequency of the i2c bus
+- gpios : the gpio used for ec request
+- slave-addr: the i2c address of the slave controller
--- /dev/null
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-alc5632"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the ALC5632's pins:
+
+ ALC5632 pins:
+
+ * SPK_OUTP
+ * SPK_OUTN
+ * HP_OUT_L
+ * HP_OUT_R
+ * AUX_OUT_P
+ * AUX_OUT_N
+ * LINE_IN_L
+ * LINE_IN_R
+ * PHONE_P
+ * PHONE_N
+ * MIC1_P
+ * MIC1_N
+ * MIC2_P
+ * MIC2_N
+ * MICBIAS1
+ * DMICDAT
+
+ Board connectors:
+
+ * Headset Stereophone
+ * Int Spk
+ * Headset Mic
+ * Digital Mic
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller
+- nvidia,audio-codec : The phandle of the ALC5632 audio codec
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-alc5632-paz00",
+ "nvidia,tegra-audio-alc5632";
+
+ nvidia,model = "Compal PAZ00";
+
+ nvidia,audio-routing =
+ "Int Spk", "SPK_OUTP",
+ "Int Spk", "SPK_OUTN",
+ "Headset Mic","MICBIAS1",
+ "MIC1_N", "Headset Mic",
+ "MIC1_P", "Headset Mic",
+ "Headset Stereophone", "HP_OUT_R",
+ "Headset Stereophone", "HP_OUT_L";
+
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&alc5632>;
+};
--- /dev/null
+NVIDIA Tegra audio complex for TrimSlice
+
+Required properties:
+- compatible : "nvidia,tegra-audio-trimslice"
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-trimslice";
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&codec>;
+};
--- /dev/null
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8753"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the WM8753's pins, and the jacks on the board:
+
+ WM8753 pins:
+
+ * LOUT1
+ * LOUT2
+ * ROUT1
+ * ROUT2
+ * MONO1
+ * MONO2
+ * OUT3
+ * OUT4
+ * LINE1
+ * LINE2
+ * RXP
+ * RXN
+ * ACIN
+ * ACOP
+ * MIC1N
+ * MIC1
+ * MIC2N
+ * MIC2
+ * Mic Bias
+
+ Board connectors:
+
+ * Headphone Jack
+ * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8753 audio codec
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-wm8753-whistler",
+ "nvidia,tegra-audio-wm8753"
+ nvidia,model = "tegra-wm8753-harmony";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "LOUT1",
+ "Headphone Jack", "ROUT1";
+
+ nvidia,i2s-controller = <&i2s1>;
+ nvidia,audio-codec = <&wm8753>;
+};
+
--- /dev/null
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8903"
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names for sources and
+ sinks are the WM8903's pins, and the jacks on the board:
+
+ WM8903 pins:
+
+ * IN1L
+ * IN1R
+ * IN2L
+ * IN2R
+ * IN3L
+ * IN3R
+ * DMICDAT
+ * HPOUTL
+ * HPOUTR
+ * LINEOUTL
+ * LINEOUTR
+ * LOP
+ * LON
+ * ROP
+ * RON
+ * MICBIAS
+
+ Board connectors:
+
+ * Headphone Jack
+ * Int Spk
+ * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Optional properties:
+- nvidia,spkr-en-gpios : The GPIO that enables the speakers
+- nvidia,hp-mute-gpios : The GPIO that mutes the headphones
+- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
+- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone
+- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone
+
+Example:
+
+sound {
+ compatible = "nvidia,tegra-audio-wm8903-harmony",
+ "nvidia,tegra-audio-wm8903"
+ nvidia,model = "tegra-wm8903-harmony";
+
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1L", "Mic Jack";
+
+ nvidia,i2s-controller = <&i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&codec 2 0>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+};
+
--- /dev/null
+NVIDIA Tegra 20 DAS (Digital Audio Switch) controller
+
+Required properties:
+- compatible : "nvidia,tegra20-das"
+- reg : Should contain DAS registers location and length
+
+Example:
+
+das@70000c00 {
+ compatible = "nvidia,tegra20-das";
+ reg = <0x70000c00 0x80>;
+};
--- /dev/null
+NVIDIA Tegra 20 I2S controller
+
+Required properties:
+- compatible : "nvidia,tegra20-i2s"
+- reg : Should contain I2S registers location and length
+- interrupts : Should contain I2S interrupt
+- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
+ request selector for this I2S controller
+
+Example:
+
+i2s@70002800 {
+ compatible = "nvidia,tegra20-i2s";
+ reg = <0x70002800 0x200>;
+ interrupts = < 45 >;
+ nvidia,dma-request-selector = < &apbdma 2 >;
+};
+++ /dev/null
-NVIDIA Tegra audio complex
-
-Required properties:
-- compatible : "nvidia,tegra-audio-alc5632"
-- nvidia,model : The user-visible name of this sound complex.
-- nvidia,audio-routing : A list of the connections between audio components.
- Each entry is a pair of strings, the first being the connection's sink,
- the second being the connection's source. Valid names for sources and
- sinks are the ALC5632's pins:
-
- ALC5632 pins:
-
- * SPK_OUTP
- * SPK_OUTN
- * HP_OUT_L
- * HP_OUT_R
- * AUX_OUT_P
- * AUX_OUT_N
- * LINE_IN_L
- * LINE_IN_R
- * PHONE_P
- * PHONE_N
- * MIC1_P
- * MIC1_N
- * MIC2_P
- * MIC2_N
- * MICBIAS1
- * DMICDAT
-
- Board connectors:
-
- * Headset Stereophone
- * Int Spk
- * Headset Mic
- * Digital Mic
-
-- nvidia,i2s-controller : The phandle of the Tegra I2S controller
-- nvidia,audio-codec : The phandle of the ALC5632 audio codec
-
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-alc5632-paz00",
- "nvidia,tegra-audio-alc5632";
-
- nvidia,model = "Compal PAZ00";
-
- nvidia,audio-routing =
- "Int Spk", "SPK_OUTP",
- "Int Spk", "SPK_OUTN",
- "Headset Mic","MICBIAS1",
- "MIC1_N", "Headset Mic",
- "MIC1_P", "Headset Mic",
- "Headset Stereophone", "HP_OUT_R",
- "Headset Stereophone", "HP_OUT_L";
-
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&alc5632>;
-};
+++ /dev/null
-NVIDIA Tegra audio complex for TrimSlice
-
-Required properties:
-- compatible : "nvidia,tegra-audio-trimslice"
-- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
-- nvidia,audio-codec : The phandle of the WM8903 audio codec
-
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-trimslice";
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&codec>;
-};
+++ /dev/null
-NVIDIA Tegra audio complex
-
-Required properties:
-- compatible : "nvidia,tegra-audio-wm8753"
-- nvidia,model : The user-visible name of this sound complex.
-- nvidia,audio-routing : A list of the connections between audio components.
- Each entry is a pair of strings, the first being the connection's sink,
- the second being the connection's source. Valid names for sources and
- sinks are the WM8753's pins, and the jacks on the board:
-
- WM8753 pins:
-
- * LOUT1
- * LOUT2
- * ROUT1
- * ROUT2
- * MONO1
- * MONO2
- * OUT3
- * OUT4
- * LINE1
- * LINE2
- * RXP
- * RXN
- * ACIN
- * ACOP
- * MIC1N
- * MIC1
- * MIC2N
- * MIC2
- * Mic Bias
-
- Board connectors:
-
- * Headphone Jack
- * Mic Jack
-
-- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
-- nvidia,audio-codec : The phandle of the WM8753 audio codec
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-wm8753-whistler",
- "nvidia,tegra-audio-wm8753"
- nvidia,model = "tegra-wm8753-harmony";
-
- nvidia,audio-routing =
- "Headphone Jack", "LOUT1",
- "Headphone Jack", "ROUT1";
-
- nvidia,i2s-controller = <&i2s1>;
- nvidia,audio-codec = <&wm8753>;
-};
-
+++ /dev/null
-NVIDIA Tegra audio complex
-
-Required properties:
-- compatible : "nvidia,tegra-audio-wm8903"
-- nvidia,model : The user-visible name of this sound complex.
-- nvidia,audio-routing : A list of the connections between audio components.
- Each entry is a pair of strings, the first being the connection's sink,
- the second being the connection's source. Valid names for sources and
- sinks are the WM8903's pins, and the jacks on the board:
-
- WM8903 pins:
-
- * IN1L
- * IN1R
- * IN2L
- * IN2R
- * IN3L
- * IN3R
- * DMICDAT
- * HPOUTL
- * HPOUTR
- * LINEOUTL
- * LINEOUTR
- * LOP
- * LON
- * ROP
- * RON
- * MICBIAS
-
- Board connectors:
-
- * Headphone Jack
- * Int Spk
- * Mic Jack
-
-- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
-- nvidia,audio-codec : The phandle of the WM8903 audio codec
-
-Optional properties:
-- nvidia,spkr-en-gpios : The GPIO that enables the speakers
-- nvidia,hp-mute-gpios : The GPIO that mutes the headphones
-- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
-- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone
-- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone
-
-Example:
-
-sound {
- compatible = "nvidia,tegra-audio-wm8903-harmony",
- "nvidia,tegra-audio-wm8903"
- nvidia,model = "tegra-wm8903-harmony";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1L", "Mic Jack";
-
- nvidia,i2s-controller = <&i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&codec 2 0>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
- nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
-};
-
+++ /dev/null
-NVIDIA Tegra 20 DAS (Digital Audio Switch) controller
-
-Required properties:
-- compatible : "nvidia,tegra20-das"
-- reg : Should contain DAS registers location and length
-
-Example:
-
-das@70000c00 {
- compatible = "nvidia,tegra20-das";
- reg = <0x70000c00 0x80>;
-};
+++ /dev/null
-NVIDIA Tegra 20 I2S controller
-
-Required properties:
-- compatible : "nvidia,tegra20-i2s"
-- reg : Should contain I2S registers location and length
-- interrupts : Should contain I2S interrupt
-- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
- request selector for this I2S controller
-
-Example:
-
-i2s@70002800 {
- compatible = "nvidia,tegra20-i2s";
- reg = <0x70002800 0x200>;
- interrupts = < 45 >;
- nvidia,dma-request-selector = < &apbdma 2 >;
-};
--- /dev/null
+NVIDIA Tegra 2 SPI device
+
+Required properties:
+- compatible : should be "nvidia,tegra20-spi".
+- gpios : should specify GPIOs used for chipselect.
+++ /dev/null
-NVIDIA Tegra 2 SPI device
-
-Required properties:
-- compatible : should be "nvidia,tegra20-spi".
-- gpios : should specify GPIOs used for chipselect.
--- /dev/null
+Tegra SOC USB controllers
+
+The device node for a USB controller that is part of a Tegra
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "nvidia,tegra20-ehci" for USB controllers
+ used in host mode.
+ - phy_type : Should be one of "ulpi" or "utmi".
+ - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
+ activated for the bus to be powered.
+
+Required properties for phy_type == ulpi:
+ - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+
+Optional properties:
+ - dr_mode : dual role mode. Indicates the working mode for
+ nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral",
+ or "otg". Default to "host" if not defined for backward compatibility.
+ host means this is a host controller
+ peripheral means it is device controller
+ otg means it can operate as either ("on the go")
+ - nvidia,has-legacy-mode : boolean indicates whether this controller can
+ operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+ registers are accessed through the APB_MISC base address instead of
+ the USB controller. Since this is a legacy issue it probably does not
+ warrant a compatible string of its own.
+++ /dev/null
-Tegra SOC USB controllers
-
-The device node for a USB controller that is part of a Tegra
-SOC is as described in the document "Open Firmware Recommended
-Practice : Universal Serial Bus" with the following modifications
-and additions :
-
-Required properties :
- - compatible : Should be "nvidia,tegra20-ehci" for USB controllers
- used in host mode.
- - phy_type : Should be one of "ulpi" or "utmi".
- - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
- activated for the bus to be powered.
-
-Required properties for phy_type == ulpi:
- - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
-
-Optional properties:
- - dr_mode : dual role mode. Indicates the working mode for
- nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral",
- or "otg". Default to "host" if not defined for backward compatibility.
- host means this is a host controller
- peripheral means it is device controller
- otg means it can operate as either ("on the go")
- - nvidia,has-legacy-mode : boolean indicates whether this controller can
- operate in legacy mode (as APX 2500 / 2600). In legacy mode some
- registers are accessed through the APB_MISC base address instead of
- the USB controller. Since this is a legacy issue it probably does not
- warrant a compatible string of its own.
projects / firefly-linux-kernel-4.4.55.git / commitdiff