system clock (of at least several MHz), rounding is less of a
problem so it can be safer to use a decimal values like 100.
+choice
+ prompt "Select a UART for early kernel messages"
+
+config AT91_EARLY_DBGU
+ bool "DBGU"
+
+config AT91_EARLY_USART0
+ bool "USART0"
+
+config AT91_EARLY_USART1
+ bool "USART1"
+
+config AT91_EARLY_USART2
+ bool "USART2"
+ depends on ! ARCH_AT91X40
+
+config AT91_EARLY_USART3
+ bool "USART3"
+ depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260)
+
+config AT91_EARLY_USART4
+ bool "USART4"
+ depends on ARCH_AT91SAM9260
+
+config AT91_EARLY_USART5
+ bool "USART5"
+ depends on ARCH_AT91SAM9260
+
+endchoice
+
endmenu
endif
#include <linux/tty_flip.h>
#include <linux/platform_device.h>
#include <linux/atmel_pdc.h>
+#include <linux/atmel_serial.h>
#include <asm/io.h>
#include <asm/arch/gpio.h>
#endif
-#include "atmel_serial.h"
-
#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
+++ /dev/null
-/*
- * drivers/serial/atmel_serial.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * USART registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef ATMEL_SERIAL_H
-#define ATMEL_SERIAL_H
-
-#define ATMEL_US_CR 0x00 /* Control Register */
-#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */
-#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */
-#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */
-#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */
-#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */
-#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */
-#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */
-#define ATMEL_US_STTBRK (1 << 9) /* Start Break */
-#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */
-#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */
-#define ATMEL_US_SENDA (1 << 12) /* Send Address */
-#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */
-#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */
-#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */
-#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */
-#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */
-#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */
-#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */
-
-#define ATMEL_US_MR 0x04 /* Mode Register */
-#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */
-#define ATMEL_US_USMODE_NORMAL 0
-#define ATMEL_US_USMODE_RS485 1
-#define ATMEL_US_USMODE_HWHS 2
-#define ATMEL_US_USMODE_MODEM 3
-#define ATMEL_US_USMODE_ISO7816_T0 4
-#define ATMEL_US_USMODE_ISO7816_T1 6
-#define ATMEL_US_USMODE_IRDA 8
-#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
-#define ATMEL_US_USCLKS_MCK (0 << 4)
-#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
-#define ATMEL_US_USCLKS_SCK (3 << 4)
-#define ATMEL_US_CHRL (3 << 6) /* Character Length */
-#define ATMEL_US_CHRL_5 (0 << 6)
-#define ATMEL_US_CHRL_6 (1 << 6)
-#define ATMEL_US_CHRL_7 (2 << 6)
-#define ATMEL_US_CHRL_8 (3 << 6)
-#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */
-#define ATMEL_US_PAR (7 << 9) /* Parity Type */
-#define ATMEL_US_PAR_EVEN (0 << 9)
-#define ATMEL_US_PAR_ODD (1 << 9)
-#define ATMEL_US_PAR_SPACE (2 << 9)
-#define ATMEL_US_PAR_MARK (3 << 9)
-#define ATMEL_US_PAR_NONE (4 << 9)
-#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
-#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */
-#define ATMEL_US_NBSTOP_1 (0 << 12)
-#define ATMEL_US_NBSTOP_1_5 (1 << 12)
-#define ATMEL_US_NBSTOP_2 (2 << 12)
-#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */
-#define ATMEL_US_CHMODE_NORMAL (0 << 14)
-#define ATMEL_US_CHMODE_ECHO (1 << 14)
-#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
-#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
-#define ATMEL_US_MSBF (1 << 16) /* Bit Order */
-#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */
-#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */
-#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */
-#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */
-#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */
-#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */
-#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */
-
-#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
-#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */
-#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */
-#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */
-#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */
-#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */
-#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */
-#define ATMEL_US_FRAME (1 << 6) /* Framing Error */
-#define ATMEL_US_PARE (1 << 7) /* Parity Error */
-#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */
-#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */
-#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */
-#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */
-#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */
-#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */
-#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */
-#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */
-#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */
-#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */
-#define ATMEL_US_RI (1 << 20) /* RI */
-#define ATMEL_US_DSR (1 << 21) /* DSR */
-#define ATMEL_US_DCD (1 << 22) /* DCD */
-#define ATMEL_US_CTS (1 << 23) /* CTS */
-
-#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
-#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
-#define ATMEL_US_CSR 0x14 /* Channel Status Register */
-#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
-#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
-#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */
-
-#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
-#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */
-
-#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
-#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */
-
-#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
-#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */
-
-#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
-#define ATMEL_US_NER 0x44 /* Number of Errors Register */
-#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
-
-#endif
#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) /* Real-Time Clock */
#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */
+#define AT91_USART0 AT91RM9200_BASE_US0
+#define AT91_USART1 AT91RM9200_BASE_US1
+#define AT91_USART2 AT91RM9200_BASE_US2
+#define AT91_USART3 AT91RM9200_BASE_US3
+
#define AT91_MATRIX 0 /* not supported */
/*
#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
+#define AT91_USART0 AT91SAM9260_BASE_US0
+#define AT91_USART1 AT91SAM9260_BASE_US1
+#define AT91_USART2 AT91SAM9260_BASE_US2
+#define AT91_USART3 AT91SAM9260_BASE_US3
+#define AT91_USART4 AT91SAM9260_BASE_US4
+#define AT91_USART5 AT91SAM9260_BASE_US5
+
/*
* Internal Memory.
#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
+#define AT91_USART0 AT91SAM9261_BASE_US0
+#define AT91_USART1 AT91SAM9261_BASE_US1
+#define AT91_USART2 AT91SAM9261_BASE_US2
+
/*
* Internal Memory.
#define AT91_RTT1 (0xfffffd50 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
+#define AT91_USART0 AT91SAM9263_BASE_US0
+#define AT91_USART1 AT91SAM9263_BASE_US1
+#define AT91_USART2 AT91SAM9263_BASE_US2
+
#define AT91_SMC AT91_SMC0
/*
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS)
+#define AT91_USART0 AT91SAM9RL_BASE_US0
+#define AT91_USART1 AT91SAM9RL_BASE_US1
+#define AT91_USART2 AT91SAM9RL_BASE_US2
+#define AT91_USART3 AT91SAM9RL_BASE_US3
+
/*
* Internal Memory.
#define __ASM_ARCH_UNCOMPRESS_H
#include <asm/io.h>
-#include <asm/arch/at91_dbgu.h>
+#include <linux/atmel_serial.h>
+
+#if defined(CONFIG_AT91_EARLY_DBGU)
+#define UART_OFFSET (AT91_DBGU + AT91_BASE_SYS)
+#elif defined(CONFIG_AT91_EARLY_USART0)
+#define UART_OFFSET AT91_USART0
+#elif defined(CONFIG_AT91_EARLY_USART1)
+#define UART_OFFSET AT91_USART1
+#elif defined(CONFIG_AT91_EARLY_USART2)
+#define UART_OFFSET AT91_USART2
+#elif defined(CONFIG_AT91_EARLY_USART3)
+#define UART_OFFSET AT91_USART3
+#elif defined(CONFIG_AT91_EARLY_USART4)
+#define UART_OFFSET AT91_USART4
+#elif defined(CONFIG_AT91_EARLY_USART5)
+#define UART_OFFSET AT91_USART5
+#endif
/*
* The following code assumes the serial port has already been
*/
static void putc(int c)
{
-#ifdef AT91_DBGU
- void __iomem *sys = (void __iomem *) AT91_BASE_SYS; /* physical address */
+#ifdef UART_OFFSET
+ void __iomem *sys = (void __iomem *) UART_OFFSET; /* physical address */
- while (!(__raw_readl(sys + AT91_DBGU_SR) & AT91_DBGU_TXRDY))
+ while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXRDY))
barrier();
- __raw_writel(c, sys + AT91_DBGU_THR);
+ __raw_writel(c, sys + ATMEL_US_THR);
#endif
}
static inline void flush(void)
{
-#ifdef AT91_DBGU
- void __iomem *sys = (void __iomem *) AT91_BASE_SYS; /* physical address */
+#ifdef UART_OFFSET
+ void __iomem *sys = (void __iomem *) UART_OFFSET; /* physical address */
/* wait for transmission to complete */
- while (!(__raw_readl(sys + AT91_DBGU_SR) & AT91_DBGU_TXEMPTY))
+ while (!(__raw_readl(sys + ATMEL_US_CSR) & ATMEL_US_TXEMPTY))
barrier();
#endif
}
--- /dev/null
+/*
+ * include/linux/atmel_serial.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * USART registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef ATMEL_SERIAL_H
+#define ATMEL_SERIAL_H
+
+#define ATMEL_US_CR 0x00 /* Control Register */
+#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */
+#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */
+#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */
+#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */
+#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */
+#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */
+#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */
+#define ATMEL_US_STTBRK (1 << 9) /* Start Break */
+#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */
+#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */
+#define ATMEL_US_SENDA (1 << 12) /* Send Address */
+#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */
+#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */
+#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */
+#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */
+#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */
+#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */
+#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */
+
+#define ATMEL_US_MR 0x04 /* Mode Register */
+#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */
+#define ATMEL_US_USMODE_NORMAL 0
+#define ATMEL_US_USMODE_RS485 1
+#define ATMEL_US_USMODE_HWHS 2
+#define ATMEL_US_USMODE_MODEM 3
+#define ATMEL_US_USMODE_ISO7816_T0 4
+#define ATMEL_US_USMODE_ISO7816_T1 6
+#define ATMEL_US_USMODE_IRDA 8
+#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
+#define ATMEL_US_USCLKS_MCK (0 << 4)
+#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
+#define ATMEL_US_USCLKS_SCK (3 << 4)
+#define ATMEL_US_CHRL (3 << 6) /* Character Length */
+#define ATMEL_US_CHRL_5 (0 << 6)
+#define ATMEL_US_CHRL_6 (1 << 6)
+#define ATMEL_US_CHRL_7 (2 << 6)
+#define ATMEL_US_CHRL_8 (3 << 6)
+#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */
+#define ATMEL_US_PAR (7 << 9) /* Parity Type */
+#define ATMEL_US_PAR_EVEN (0 << 9)
+#define ATMEL_US_PAR_ODD (1 << 9)
+#define ATMEL_US_PAR_SPACE (2 << 9)
+#define ATMEL_US_PAR_MARK (3 << 9)
+#define ATMEL_US_PAR_NONE (4 << 9)
+#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
+#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */
+#define ATMEL_US_NBSTOP_1 (0 << 12)
+#define ATMEL_US_NBSTOP_1_5 (1 << 12)
+#define ATMEL_US_NBSTOP_2 (2 << 12)
+#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */
+#define ATMEL_US_CHMODE_NORMAL (0 << 14)
+#define ATMEL_US_CHMODE_ECHO (1 << 14)
+#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
+#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
+#define ATMEL_US_MSBF (1 << 16) /* Bit Order */
+#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */
+#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */
+#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */
+#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */
+#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */
+#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */
+#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */
+
+#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
+#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */
+#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */
+#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */
+#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */
+#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */
+#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */
+#define ATMEL_US_FRAME (1 << 6) /* Framing Error */
+#define ATMEL_US_PARE (1 << 7) /* Parity Error */
+#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */
+#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */
+#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */
+#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */
+#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */
+#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */
+#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */
+#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */
+#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */
+#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */
+#define ATMEL_US_RI (1 << 20) /* RI */
+#define ATMEL_US_DSR (1 << 21) /* DSR */
+#define ATMEL_US_DCD (1 << 22) /* DCD */
+#define ATMEL_US_CTS (1 << 23) /* CTS */
+
+#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
+#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
+#define ATMEL_US_CSR 0x14 /* Channel Status Register */
+#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
+#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
+#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */
+
+#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
+#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */
+
+#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
+#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */
+
+#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
+#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */
+
+#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
+#define ATMEL_US_NER 0x44 /* Number of Errors Register */
+#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
+
+#endif
projects / firefly-linux-kernel-4.4.55.git / commitdiff