Peng Tao [Fri, 11 Sep 2015 03:14:06 +0000 (11:14 +0800)]
nfs: fix pg_test page count calculation
We really want sizeof(struct page *) instead. Otherwise we limit
maximum IO size to 64 pages rather than 512 pages on a 64bit system.
Fixes
2e11f829(nfs: cap request size to fit a kmalloced page array).
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Peng Tao <tao.peng@primarydata.com>
Fixes: 2e11f8296d22 ("nfs: cap request size to fit a kmalloced page array")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Olga Kornievskaia [Mon, 14 Sep 2015 23:54:36 +0000 (19:54 -0400)]
Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount
A test case is as the description says:
open(foobar, O_WRONLY);
sleep() --> reboot the server
close(foobar)
The bug is because in nfs4state.c in nfs4_reclaim_open_state() a few
line before going to restart, there is
clear_bit(NFS4CLNT_RECLAIM_NOGRACE, &state->flags).
NFS4CLNT_RECLAIM_NOGRACE is a flag for the client states not open
owner states. Value of NFS4CLNT_RECLAIM_NOGRACE is 4 which is the
value of NFS_O_WRONLY_STATE in nfs4_state->flags. So clearing it wipes
out state and when we go to close it, “call_close” doesn’t get set as
state flag is not set and CLOSE doesn’t go on the wire.
Signed-off-by: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Linus Torvalds [Sat, 12 Sep 2015 23:35:56 +0000 (16:35 -0700)]
Linux 4.3-rc1
Linus Torvalds [Sat, 12 Sep 2015 19:24:29 +0000 (12:24 -0700)]
Merge tag 'cris-for-4.3' of git://git./linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Mostly removal of old cruft of which we can use a generic version, or
fixes for code not commonly run in the cris port, but also additions
to enable some good debug"
* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
CRISv10: delete unused lib/dmacopy.c
CRISv10: delete unused lib/old_checksum.c
CRIS: fix switch_mm() lockdep splat
CRISv32: enable LOCKDEP_SUPPORT
CRIS: add STACKTRACE_SUPPORT
CRISv32: annotate irq enable in idle loop
CRISv32: add support for irqflags tracing
CRIS: UAPI: use generic types.h
CRIS: UAPI: use generic shmbuf.h
CRIS: UAPI: use generic msgbuf.h
CRIS: UAPI: use generic socket.h
CRIS: UAPI: use generic sembuf.h
CRIS: UAPI: use generic sockios.h
CRIS: UAPI: use generic auxvec.h
CRIS: UAPI: use generic headers via Kbuild
CRIS: UAPI: fix elf.h export
CRIS: don't make asm/elf.h depend on asm/user.h
CRIS: UAPI: fix ptrace.h
CRISv32: Squash compile warnings for axisflashmap
CRISv32: Add GPIO driver to the default configs
...
Linus Torvalds [Wed, 27 May 2015 22:32:15 +0000 (15:32 -0700)]
blk: rq_data_dir() should not return a boolean
rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.
Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct
switch (rq_data_dir(req)) {
case READ:
...
case WRITE:
...
that we have in a few drivers.
Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:
drivers/block/hd.c: In function ‘hd_request’:
drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
switch (rq_data_dir(req)) {
The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit
5953316dbf90 ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.
But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Sep 2015 18:19:01 +0000 (11:19 -0700)]
Merge branch 'writeback-plugging'
Fix up the writeback plugging introduced in commit
d353d7587d02
("writeback: plug writeback at a high level") that then caused problems
due to the unplug happening with a spinlock held.
* writeback-plugging:
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
Revert "writeback: plug writeback at a high level"
Linus Torvalds [Fri, 11 Sep 2015 20:37:19 +0000 (13:37 -0700)]
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
We had to revert the pluggin in writeback_sb_inodes() because the
wb->list_lock is held, but we could easily plug at a higher level before
taking that lock, and unplug after releasing it. This does that.
Chris will run performance numbers, just to verify that this approach is
comparable to the alternative (we could just drop and re-take the lock
around the blk_finish_plug() rather than these two commits.
I'd have preferred waiting for actual performance numbers before picking
one approach over the other, but I don't want to release rc1 with the
known "sleeping function called from invalid context" issue, so I'll
pick this cleanup version for now. But if the numbers show that we
really want to plug just at the writeback_sb_inodes() level, and we
should just play ugly games with the spinlock, we'll switch to that.
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Sep 2015 03:06:59 +0000 (20:06 -0700)]
thermal: fix intel PCH thermal driver mismerge
I didn't notice this when merging the thermal code from Zhang, but his
merge (commit
5a924a07f882: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit
17e8351a7739 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit
d0a12625d2ff
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
This fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Sep 2015 02:34:09 +0000 (19:34 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge fourth patch-bomb from Andrew Morton:
- sys_membarier syscall
- seq_file interface changes
- a few misc fixups
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
mm/early_ioremap: add explicit #include of asm/early_ioremap.h
fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
selftests: enhance membarrier syscall test
selftests: add membarrier syscall test
sys_membarrier(): system-wide memory barrier (generic, x86)
MODSIGN: fix a compilation warning in extract-cert
Vineet Gupta [Fri, 11 Sep 2015 23:32:22 +0000 (16:32 -0700)]
ARCv2: [axs103_smp] Reduce clk for SMP FPGA configs
Newer bitfiles needs the reduced clk even for SMP builds
Cc: <stable@vger.kernel.org> #4.2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Sep 2015 02:29:00 +0000 (19:29 -0700)]
Merge tag 'ntb-4.3' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason:
"NTB bug and documentation fixes, new device IDs, performance
improvements, and adding a mailing list to MAINTAINERS for NTB"
* tag 'ntb-4.3' of git://github.com/jonmason/ntb:
NTB: Fix range check on memory window index
NTB: Improve index handling in B2B MW workaround
NTB: Fix documentation for ntb_peer_db_clear.
NTB: Fix documentation for ntb_link_is_up
NTB: Use unique DMA channels for TX and RX
NTB: Remove dma_sync_wait from ntb_async_rx
NTB: Clean up QP stats info
NTB: Make the transport list in order of discovery
NTB: Add PCI Device IDs for Broadwell Xeon
NTB: Add flow control to the ntb_netdev
NTB: Add list to MAINTAINERS
Linus Torvalds [Sat, 12 Sep 2015 02:17:28 +0000 (19:17 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
Linus Torvalds [Sat, 12 Sep 2015 02:11:06 +0000 (19:11 -0700)]
Merge tag 'pm+acpi-4.3-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups on top of the previous PM+ACPI
pull request (cpufreq core and drivers, cpuidle, generic power domains
framework). Some of them didn't make to that pull request and some
fix issues introduced by it.
The only really new thing is the support for suspend frequency in the
cpufreq-dt driver, but it is needed to fix an issue with Exynos
platforms.
Specifics:
- build fix for the new Mediatek MT8173 cpufreq driver (Guenter
Roeck).
- generic power domains framework fixes (power on error code path,
subdomain removal) and cleanup of a deprecated API user (Geert
Uytterhoeven, Jon Hunter, Ulf Hansson).
- cpufreq-dt driver fixes including two fixes for bugs related to the
new Operating Performance Points Device Tree bindings introduced
recently (Viresh Kumar).
- suspend frequency support for the cpufreq-dt driver (Bartlomiej
Zolnierkiewicz, Viresh Kumar).
- cpufreq core cleanups (Viresh Kumar).
- intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi).
- additional sanity check in the cpuidle core (Xunlei Pang).
- fix for a comment related to CPU power management (Lina Iyer)"
* tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: fix PCT_TO_HWP macro
intel_pstate: Fix user input of min/max to legal policy region
PM / OPP: Return suspend_opp only if it is enabled
cpufreq-dt: add suspend frequency support
cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
PM / OPP: add dev_pm_opp_get_suspend_opp() helper
staging: board: Migrate away from __pm_genpd_name_add_device()
cpufreq: Use __func__ to print function's name
cpufreq: staticize cpufreq_cpu_get_raw()
PM / Domains: Ensure subdomain is not in use before removing
cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
cpuidle/coupled: Add sanity check for safe_state_index
PM / Domains: Try power off masters in error path of __pm_genpd_poweron()
cpufreq: dt: Tolerance applies on both sides of target voltage
cpufreq: dt: Print error on failing to mark OPPs as shared
cpufreq: dt: Check OPP count before marking them shared
kernel/cpu_pm: fix cpu_cluster_pm_exit comment
Linus Torvalds [Sat, 12 Sep 2015 02:00:42 +0000 (19:00 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target-pending updates for v4.3-rc1.
Mostly bug-fixes and minor changes this round. The fallout from the
big v4.2-rc1 RCU conversion have (thus far) been minimal.
The highlights this round include:
- Move sense handling routines into scsi_common code (Sagi)
- Return ABORTED_COMMAND sense key for PI errors (Sagi)
- Add tpg_enabled_sendtargets attribute for disabled iscsi-target
discovery (David)
- Shrink target struct se_cmd by rearranging fields (Roland)
- Drop iSCSI use of mutex around max_cmd_sn increment (Roland)
- Replace iSCSI __kernel_sockaddr_storage with sockaddr_storage (Andy +
Chris)
- Honor fabric max_data_sg_nents I/O transfer limit (Arun + Himanshu +
nab)
- Fix EXTENDED_COPY >= v4.1 regression OOPsen (Alex + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (37 commits)
target: use stringify.h instead of own definition
target/user: Fix UFLAG_UNKNOWN_OP handling
target: Remove no-op conditional
target/user: Remove unused variable
target: Fix max_cmd_sn increment w/o cmdsn mutex regressions
target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess
target/qla2xxx: Honor max_data_sg_nents I/O transfer limit
target/iscsi: Replace __kernel_sockaddr_storage with sockaddr_storage
target/iscsi: Replace conn->login_ip with login_sockaddr
target/iscsi: Keep local_ip as the actual sockaddr
target/iscsi: Fix np_ip bracket issue by removing np_ip
target: Drop iSCSI use of mutex around max_cmd_sn increment
qla2xxx: Update tcm_qla2xxx module description to 24xx+
iscsi-target: Add tpg_enabled_sendtargets for disabled discovery
drivers: target: Drop unlikely before IS_ERR(_OR_NULL)
target: check DPO/FUA usage for COMPARE AND WRITE
target: Shrink struct se_cmd by rearranging fields
target: Remove cmd->se_ordered_id (unused except debug log lines)
target: add support for START_STOP_UNIT SCSI opcode
target: improve unsupported opcode message
...
Linus Torvalds [Sat, 12 Sep 2015 01:15:18 +0000 (18:15 -0700)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull second round of SCSI updates from James Bottomley:
"There's one late arriving patch here (added today), fixing a build
issue which the scsi_dh patch set in here uncovered. Other than that,
everything has been incubated in -next and the checkers for a week.
The major pieces of this patch are a set patches facilitating better
integration between scsi and scsi_dh (the device handling layer used
by multi-path; all the dm parts are acked by Mike Snitzer).
This also includes driver updates for mp3sas, scsi_debug and an
assortment of bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (50 commits)
scsi_dh: fix randconfig build error
scsi: fix scsi_error_handler vs. scsi_host_dev_release race
fcoe: Convert use of __constant_htons to htons
mpt2sas: setpci reset kernel oops fix
pm80xx: Don't override ts->stat on IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
lpfc: Fix possible use-after-free and double free in lpfc_mbx_cmpl_rdp_page_a2()
bfa: Fix incorrect de-reference of pointer
bfa: Fix indentation
scsi_transport_sas: Remove check for SAS expander when querying bay/enclosure IDs.
scsi_debug: resp_request: remove unused variable
scsi_debug: fix REPORT LUNS Well Known LU
scsi_debug: schedule_resp fix input variable check
scsi_debug: make dump_sector static
scsi_debug: vfree is null safe so drop the check
scsi_debug: use SCSI_W_LUN_REPORT_LUNS instead of SAM2_WLUN_REPORT_LUNS;
scsi_debug: define pr_fmt() for consistent logging
mpt2sas: Refcount fw_events and fix unsafe list usage
mpt2sas: Refcount sas_device objects and fix unsafe list usage
scsi_dh: return SCSI_DH_NOTCONN in scsi_dh_activate()
scsi_dh: don't allow to detach device handlers at runtime
...
Linus Torvalds [Fri, 11 Sep 2015 23:42:39 +0000 (16:42 -0700)]
Merge tag 'media/v4.3-2' of git://git./linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"A series of patches that move part of the code used to allocate memory
from the media subsystem to the mm subsystem"
[ The mm parts have been acked by VM people, and the series was
apparently in -mm for a while - Linus ]
* tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames()
[media] media: vb2: Remove unused functions
[media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector
[media] vb2: Provide helpers for mapping virtual addresses
[media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns()
[media] mm: Provide new get_vaddr_frames() helper
[media] vb2: Push mmap_sem down to memops
Linus Torvalds [Fri, 11 Sep 2015 23:21:12 +0000 (16:21 -0700)]
Merge tag 'edac/v4.3-1' of git://git./linux/kernel/git/mchehab/linux-edac
Pull edac updates from Mauro Carvalho Chehab:
"Two EDAC fixes for Intel systems (Haswell and Ivy Bridge)"
* tag 'edac/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: correctly fetch DIMM width on Ivy Bridge and Haswell
sb_edac: look harder for DDRIO on Haswell systems
Linus Torvalds [Fri, 11 Sep 2015 23:13:47 +0000 (16:13 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
Andrew Morton [Fri, 11 Sep 2015 20:07:53 +0000 (13:07 -0700)]
revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
Revert commit
f83c7b5e9fd6 ("ocfs2/dlm: use list_for_each_entry instead
of list_for_each").
list_for_each_entry() will dereference its `pos' argument, which can be
NULL in dlm_process_recovery_data().
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Fengguang Wu <fengguang.wu@gmail.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ard Biesheuvel [Fri, 11 Sep 2015 20:07:50 +0000 (13:07 -0700)]
mm/early_ioremap: add explicit #include of asm/early_ioremap.h
Commit
6b0f68e32ea8 ("mm: add utility for early copy from unmapped ram")
introduces a function copy_from_early_mem() into mm/early_ioremap.c
which itself calls early_memremap()/early_memunmap(). However, since
early_memunmap() has not been declared yet at this point in the .c file,
nor by any explicitly included header files, we are depending on a
transitive include of asm/early_ioremap.h to declare it, which is
fragile.
So instead, include this header explicitly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 11 Sep 2015 20:07:48 +0000 (13:07 -0700)]
fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
The seq_<foo> function return values were frequently misused.
See: commit
1f33c41c03da ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
All uses of these return values have been removed, so convert the
return types to void.
Miscellanea:
o Move seq_put_decimal_<type> and seq_escape prototypes closer the
other seq_vprintf prototypes
o Reorder seq_putc and seq_puts to return early on overflow
o Add argument names to seq_vprintf and seq_printf
o Update the seq_escape kernel-doc
o Convert a couple of leading spaces to tabs in seq_escape
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mathieu Desnoyers [Fri, 11 Sep 2015 20:07:45 +0000 (13:07 -0700)]
selftests: enhance membarrier syscall test
Update the membarrier syscall self-test to match the membarrier
interface. Extend coverage of the interface. Consider ENOSYS as a
"SKIP" test, since it is a valid configuration, but does not allow
testing the system call.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pranith Kumar [Fri, 11 Sep 2015 20:07:42 +0000 (13:07 -0700)]
selftests: add membarrier syscall test
Add a self test for the membarrier system call.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mathieu Desnoyers [Fri, 11 Sep 2015 20:07:39 +0000 (13:07 -0700)]
sys_membarrier(): system-wide memory barrier (generic, x86)
Here is an implementation of a new system call, sys_membarrier(), which
executes a memory barrier on all threads running on the system. It is
implemented by calling synchronize_sched(). It can be used to
distribute the cost of user-space memory barriers asymmetrically by
transforming pairs of memory barriers into pairs consisting of
sys_membarrier() and a compiler barrier. For synchronization primitives
that distinguish between read-side and write-side (e.g. userspace RCU
[1], rwlocks), the read-side can be accelerated significantly by moving
the bulk of the memory barrier overhead to the write-side.
The existing applications of which I am aware that would be improved by
this system call are as follows:
* Through Userspace RCU library (http://urcu.so)
- DNS server (Knot DNS) https://www.knot-dns.cz/
- Network sniffer (http://netsniff-ng.org/)
- Distributed object storage (https://sheepdog.github.io/sheepdog/)
- User-space tracing (http://lttng.org)
- Network storage system (https://www.gluster.org/)
- Virtual routers (https://events.linuxfoundation.org/sites/events/files/slides/DPDK_RCU_0MQ.pdf)
- Financial software (https://lkml.org/lkml/2015/3/23/189)
Those projects use RCU in userspace to increase read-side speed and
scalability compared to locking. Especially in the case of RCU used by
libraries, sys_membarrier can speed up the read-side by moving the bulk of
the memory barrier cost to synchronize_rcu().
* Direct users of sys_membarrier
- core dotnet garbage collector (https://github.com/dotnet/coreclr/issues/198)
Microsoft core dotnet GC developers are planning to use the mprotect()
side-effect of issuing memory barriers through IPIs as a way to implement
Windows FlushProcessWriteBuffers() on Linux. They are referring to
sys_membarrier in their github thread, specifically stating that
sys_membarrier() is what they are looking for.
To explain the benefit of this scheme, let's introduce two example threads:
Thread A (non-frequent, e.g. executing liburcu synchronize_rcu())
Thread B (frequent, e.g. executing liburcu
rcu_read_lock()/rcu_read_unlock())
In a scheme where all smp_mb() in thread A are ordering memory accesses
with respect to smp_mb() present in Thread B, we can change each
smp_mb() within Thread A into calls to sys_membarrier() and each
smp_mb() within Thread B into compiler barriers "barrier()".
Before the change, we had, for each smp_mb() pairs:
Thread A Thread B
previous mem accesses previous mem accesses
smp_mb() smp_mb()
following mem accesses following mem accesses
After the change, these pairs become:
Thread A Thread B
prev mem accesses prev mem accesses
sys_membarrier() barrier()
follow mem accesses follow mem accesses
As we can see, there are two possible scenarios: either Thread B memory
accesses do not happen concurrently with Thread A accesses (1), or they
do (2).
1) Non-concurrent Thread A vs Thread B accesses:
Thread A Thread B
prev mem accesses
sys_membarrier()
follow mem accesses
prev mem accesses
barrier()
follow mem accesses
In this case, thread B accesses will be weakly ordered. This is OK,
because at that point, thread A is not particularly interested in
ordering them with respect to its own accesses.
2) Concurrent Thread A vs Thread B accesses
Thread A Thread B
prev mem accesses prev mem accesses
sys_membarrier() barrier()
follow mem accesses follow mem accesses
In this case, thread B accesses, which are ensured to be in program
order thanks to the compiler barrier, will be "upgraded" to full
smp_mb() by synchronize_sched().
* Benchmarks
On Intel Xeon E5405 (8 cores)
(one thread is calling sys_membarrier, the other 7 threads are busy
looping)
1000 non-expedited sys_membarrier calls in 33s =3D 33 milliseconds/call.
* User-space user of this system call: Userspace RCU library
Both the signal-based and the sys_membarrier userspace RCU schemes
permit us to remove the memory barrier from the userspace RCU
rcu_read_lock() and rcu_read_unlock() primitives, thus significantly
accelerating them. These memory barriers are replaced by compiler
barriers on the read-side, and all matching memory barriers on the
write-side are turned into an invocation of a memory barrier on all
active threads in the process. By letting the kernel perform this
synchronization rather than dumbly sending a signal to every process
threads (as we currently do), we diminish the number of unnecessary wake
ups and only issue the memory barriers on active threads. Non-running
threads do not need to execute such barrier anyway, because these are
implied by the scheduler context switches.
Results in liburcu:
Operations in 10s, 6 readers, 2 writers:
memory barriers in reader:
1701557485 reads,
2202847 writes
signal-based scheme:
9830061167 reads, 6700 writes
sys_membarrier:
9952759104 reads, 425 writes
sys_membarrier (dyn. check):
7970328887 reads, 425 writes
The dynamic sys_membarrier availability check adds some overhead to
the read-side compared to the signal-based scheme, but besides that,
sys_membarrier slightly outperforms the signal-based scheme. However,
this non-expedited sys_membarrier implementation has a much slower grace
period than signal and memory barrier schemes.
Besides diminishing the number of wake-ups, one major advantage of the
membarrier system call over the signal-based scheme is that it does not
need to reserve a signal. This plays much more nicely with libraries,
and with processes injected into for tracing purposes, for which we
cannot expect that signals will be unused by the application.
An expedited version of this system call can be added later on to speed
up the grace period. Its implementation will likely depend on reading
the cpu_curr()->mm without holding each CPU's rq lock.
This patch adds the system call to x86 and to asm-generic.
[1] http://urcu.so
membarrier(2) man page:
MEMBARRIER(2) Linux Programmer's Manual MEMBARRIER(2)
NAME
membarrier - issue memory barriers on a set of threads
SYNOPSIS
#include <linux/membarrier.h>
int membarrier(int cmd, int flags);
DESCRIPTION
The cmd argument is one of the following:
MEMBARRIER_CMD_QUERY
Query the set of supported commands. It returns a bitmask of
supported commands.
MEMBARRIER_CMD_SHARED
Execute a memory barrier on all threads running on the system.
Upon return from system call, the caller thread is ensured that
all running threads have passed through a state where all memory
accesses to user-space addresses match program order between
entry to and return from the system call (non-running threads
are de facto in such a state). This covers threads from all pro=E2=80=90
cesses running on the system. This command returns 0.
The flags argument needs to be 0. For future extensions.
All memory accesses performed in program order from each targeted
thread is guaranteed to be ordered with respect to sys_membarrier(). If
we use the semantic "barrier()" to represent a compiler barrier forcing
memory accesses to be performed in program order across the barrier,
and smp_mb() to represent explicit memory barriers forcing full memory
ordering across the barrier, we have the following ordering table for
each pair of barrier(), sys_membarrier() and smp_mb():
The pair ordering is detailed as (O: ordered, X: not ordered):
barrier() smp_mb() sys_membarrier()
barrier() X X O
smp_mb() X O O
sys_membarrier() O O O
RETURN VALUE
On success, these system calls return zero. On error, -1 is returned,
and errno is set appropriately. For a given command, with flags
argument set to 0, this system call is guaranteed to always return the
same value until reboot.
ERRORS
ENOSYS System call is not implemented.
EINVAL Invalid arguments.
Linux 2015-04-15 MEMBARRIER(2)
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Miell <nmiell@comcast.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 11 Sep 2015 20:07:36 +0000 (13:07 -0700)]
MODSIGN: fix a compilation warning in extract-cert
Fix the following warning when compiling extract-cert:
scripts/extract-cert.c: In function `write_cert':
scripts/extract-cert.c:89:2: warning: format not a string literal and no format arguments [-Wformat-security]
ERR(!i2d_X509_bio(wb, x509), cert_dst);
^
whereby the ERR() macro is taking cert_dst as the format string. "%s"
should be used as the format string as the path could contain special
characters.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Jim Davis <jim.epost@gmail.com>
Acked-by : David Woodhouse <david.woodhouse@intel.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 11 Sep 2015 22:12:59 +0000 (15:12 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- new driver for NXP LPC18xx Watchdog Timer
- new driver for SAMA5D4 watchdog timer
- add support for MCP79 to nv_tco driver
- clean-up and improvement of the mpc8xxx watchdog driver
- improvements to gpio-wdt
- at91sam9_wdt clock improvements
... and other small fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
Watchdog: Fix parent of watchdog_devices
watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
watchdog: at91sam9: get and use slow clock
Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
watchdog: add a driver to support SAMA5D4 watchdog timer
watchdog: mpc8xxx: allow to compile for MPC512x
watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
watchdog: mpc8xxx: use dynamic memory for device specific data
watchdog: mpc8xxx: use devm_ioremap_resource to map memory
watchdog: mpc8xxx: make use of of_device_get_match_data
watchdog: mpc8xxx: simplify registration
watchdog: mpc8xxx: remove dead code
watchdog: lpc18xx_wdt_get_timeleft() can be static
DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
watchdog: NXP LPC18xx Watchdog Timer Driver
watchdog: gpio-wdt: ping already at startup for always running devices
watchdog: gpio-wdt: be more strict about hw_algo matching
Documentation: watchdog: at91sam9_wdt: add clocks property
watchdog: booke_wdt: Use infrastructure to check timeout limits
watchdog: (nv_tco) add support for MCP79
...
Linus Torvalds [Fri, 11 Sep 2015 20:26:39 +0000 (13:26 -0700)]
Revert "writeback: plug writeback at a high level"
This reverts commit
d353d7587d02116b9732d5c06615aed75a4d3a47.
Doing the block layer plug/unplug inside writeback_sb_inodes() is
broken, because that function is actually called with a spinlock held:
wb->list_lock, as pointed out by Chris Mason.
Chris suggested just dropping and re-taking the spinlock around the
blk_finish_plug() call (the plgging itself can happen under the
spinlock), and that would technically work, but is just disgusting.
We do something fairly similar - but not quite as disgusting because we
at least have a better reason for it - in writeback_single_inode(), so
it's not like the caller can depend on the lock being held over the
call, but in this case there just isn't any good reason for that
"release and re-take the lock" pattern.
[ In general, we should really strive to avoid the "release and retake"
pattern for locks, because in the general case it can easily cause
subtle bugs when the caller caches any state around the call that
might be invalidated by dropping the lock even just temporarily. ]
But in this case, the plugging should be easy to just move up to the
callers before the spinlock is taken, which should even improve the
effectiveness of the plug. So there is really no good reason to play
games with locking here.
I'll send off a test-patch so that Dave Chinner can verify that that
plug movement works. In the meantime this just reverts the problematic
commit and adds a comment to the function so that we hopefully don't
make this mistake again.
Reported-by: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 11 Sep 2015 19:38:25 +0000 (12:38 -0700)]
Merge branch 'for-linus-4.3' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs cleanups and fixes from Chris Mason:
"These are small cleanups, and also some fixes for our async worker
thread initialization.
I was having some trouble testing these, but it ended up being a
combination of changing around my test servers and a shiny new
schedule while atomic from the new start/finish_plug in
writeback_sb_inodes().
That one only hits on btrfs raid5/6 or MD raid10, and if I wasn't
changing a bunch of things in my test setup at once it would have been
really clear. Fix for writeback_sb_inodes() on the way as well"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: cleanup: remove unnecessary check before btrfs_free_path is called
btrfs: async_thread: Fix workqueue 'max_active' value when initializing
btrfs: Add raid56 support for updating num_tolerated_disk_barrier_failures in btrfs_balance
btrfs: Cleanup for btrfs_calc_num_tolerated_disk_barrier_failures
btrfs: Remove noused chunk_tree and chunk_objectid from scrub_enumerate_chunks and scrub_chunk
btrfs: Update out-of-date "skip parity stripe" comment
Linus Torvalds [Fri, 11 Sep 2015 19:33:03 +0000 (12:33 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph update from Sage Weil:
"There are a few fixes for snapshot behavior with CephFS and support
for the new keepalive protocol from Zheng, a libceph fix that affects
both RBD and CephFS, a few bug fixes and cleanups for RBD from Ilya,
and several small fixes and cleanups from Jianpeng and others"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: improve readahead for file holes
ceph: get inode size for each append write
libceph: check data_len in ->alloc_msg()
libceph: use keepalive2 to verify the mon session is alive
rbd: plug rbd_dev->header.object_prefix memory leak
rbd: fix double free on rbd_dev->header_name
libceph: set 'exists' flag for newly up osd
ceph: cleanup use of ceph_msg_get
ceph: no need to get parent inode in ceph_open
ceph: remove the useless judgement
ceph: remove redundant test of head->safe and silence static analysis warnings
ceph: fix queuing inode to mdsdir's snaprealm
libceph: rename con_work() to ceph_con_workfn()
libceph: Avoid holding the zero page on ceph_msgr_slab_init errors
libceph: remove the unused macro AES_KEY_SIZE
ceph: invalidate dirty pages after forced umount
ceph: EIO all operations after forced umount
Linus Torvalds [Fri, 11 Sep 2015 19:23:51 +0000 (12:23 -0700)]
Merge tag 'gfs2-merge-window' of git://git./linux/kernel/git/gfs2/linux-gfs2
Pull GFS2 updates from Bob Peterson:
"Here is a list of patches we've accumulated for GFS2 for the current
upstream merge window. This time we've only got six patches, many of
which are very small:
- three cleanups from Andreas Gruenbacher, including a nice cleanup
of the sequence file code for the sbstats debugfs file.
- a patch from Ben Hutchings that changes statistics variables from
signed to unsigned.
- two patches from me that increase GFS2's glock scalability by
switching from a conventional hash table to rhashtable"
* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: A minor "sbstats" cleanup
gfs2: Fix a typo in a comment
gfs2: Make statistics unsigned, suitable for use with do_div()
GFS2: Use resizable hash table for glocks
GFS2: Move glock superblock pointer to field gl_name
gfs2: Simplify the seq file code for "sbstats"
Christoph Hellwig [Wed, 9 Sep 2015 16:04:18 +0000 (18:04 +0200)]
scsi_dh: fix randconfig build error
It looks like the Kconfig check that was meant to fix this (commit
fe9233fb6914a0eb20166c967e3020f7f0fba2c9 [SCSI] scsi_dh: fix kconfig related
build errors) was actually reversed, but no-one noticed until the new set of
patches which separated DM and SCSI_DH).
Fixes: fe9233fb6914a0eb20166c967e3020f7f0fba2c9
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Linus Torvalds [Fri, 11 Sep 2015 16:42:32 +0000 (09:42 -0700)]
Merge tag 'sound-fix-4.3-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes since the last update: the HD-audio quirks
as usual with a USB-audio fix and a trivial fix for the old sparc
driver"
* tag 'sound-fix-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Change internal PCM order
ALSA: hda - Fix white noise on Dell M3800
ALSA: hda - Use ALC880_FIXUP_FUJITSU for FSC Amilo M1437
ALSA: hda - Enable headphone jack detect on old Fujitsu laptops
ALSA: sparc: amd7930: Fix module autoload for OF platform driver
ALSA: hda - Add some FIXUP quirks for white noise on Dell laptop.
Linus Torvalds [Fri, 11 Sep 2015 16:35:56 +0000 (09:35 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just a bunch of fixes to squeeze in before -rc1:
- three nouveau regression fixes
- one qxl regression fix
- a bunch of i915 fixes
... and some core displayport/atomic fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
drm/qxl: validate monitors config modes
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
Dmitry Torokhov [Fri, 11 Sep 2015 16:02:36 +0000 (09:02 -0700)]
Merge branch 'next' into for-linus
Prepare second round of input updates for 4.3 merge window.
Rafael J. Wysocki [Fri, 11 Sep 2015 13:37:36 +0000 (15:37 +0200)]
Merge branches 'pm-cpu', 'pm-cpuidle' and 'pm-domains'
* pm-cpu:
kernel/cpu_pm: fix cpu_cluster_pm_exit comment
* pm-cpuidle:
cpuidle/coupled: Add sanity check for safe_state_index
* pm-domains:
staging: board: Migrate away from __pm_genpd_name_add_device()
PM / Domains: Ensure subdomain is not in use before removing
PM / Domains: Try power off masters in error path of __pm_genpd_poweron()
Rafael J. Wysocki [Fri, 11 Sep 2015 13:37:25 +0000 (15:37 +0200)]
Merge branch 'pm-cpufreq'
* pm-cpufreq:
intel_pstate: fix PCT_TO_HWP macro
intel_pstate: Fix user input of min/max to legal policy region
cpufreq-dt: add suspend frequency support
cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
cpufreq: Use __func__ to print function's name
cpufreq: staticize cpufreq_cpu_get_raw()
cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
cpufreq: dt: Tolerance applies on both sides of target voltage
cpufreq: dt: Print error on failing to mark OPPs as shared
cpufreq: dt: Check OPP count before marking them shared
Rafael J. Wysocki [Fri, 11 Sep 2015 13:37:17 +0000 (15:37 +0200)]
Merge branch 'pm-opp'
* pm-opp:
PM / OPP: Return suspend_opp only if it is enabled
PM / OPP: add dev_pm_opp_get_suspend_opp() helper
David Disseldorp [Thu, 3 Sep 2015 23:39:56 +0000 (01:39 +0200)]
target: use stringify.h instead of own definition
Signed-off-by: David Disseldorp <ddiss@suse.de>
Acked-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Andy Grover [Thu, 3 Sep 2015 23:03:44 +0000 (16:03 -0700)]
target/user: Fix UFLAG_UNKNOWN_OP handling
Calling transport_generic_request_failure() from here causes list
corruption. We should be using target_complete_cmd() instead.
Which we do in all other cases, so the UNKNOWN_OP case can become just
another member of the big else/if chain in tcmu_handle_completion().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Andy Grover [Thu, 3 Sep 2015 23:03:43 +0000 (16:03 -0700)]
target: Remove no-op conditional
This does nothing, and there are many other places where
transport_cmd_check_stop_to_fabric()'s retval is not checked>, If we
wanted to check it here, we should probably do it those other places too.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Andy Grover [Thu, 3 Sep 2015 23:03:42 +0000 (16:03 -0700)]
target/user: Remove unused variable
We don't use it any more.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Tue, 8 Sep 2015 13:14:18 +0000 (06:14 -0700)]
target: Fix max_cmd_sn increment w/o cmdsn mutex regressions
Current for-next iscsi target is broken:
commit
109e2381749c1cfd94a0d22b2b54142539024973
Author: Roland Dreier <roland@purestorage.com>
Date: Thu Jul 23 14:53:32 2015 -0700
target: Drop iSCSI use of mutex around max_cmd_sn increment
This patch fixes incorrect pr_debug() + atomic_inc_return() usage
within iscsit_increment_maxcmdsn() code.
Also fix funny iscsit_determine_maxcmdsn() usage and update
iscsi_target_do_tx_login_io() code.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Thu, 3 Sep 2015 06:30:45 +0000 (06:30 +0000)]
target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess
This patch is a >= v4.1 regression bug-fix where control CDB
emulation logic in commit
38b57f82 now expects a se_cmd->se_sess
pointer to exist when determining T10-PI support is to be exposed
for initiator host ports.
To address this bug, go ahead and add locally generated se_cmd
descriptors for copy-offload block-copy to it's own stand-alone
se_session nexus, while the parent EXTENDED_COPY se_cmd descriptor
remains associated with it's originating se_cmd->se_sess nexus.
Note a valid se_cmd->se_sess is also required for future support
of WRITE_INSERT and READ_STRIP software emulation when submitting
backend I/O to se_device that exposes T10-PI suport.
Reported-by: Alex Gorbachev <ag@iss-integration.com>
Tested-by: Alex Gorbachev <ag@iss-integration.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Fri, 31 Jul 2015 01:28:13 +0000 (18:28 -0700)]
target/qla2xxx: Honor max_data_sg_nents I/O transfer limit
This patch adds an optional fabric driver provided SGL limit
that target-core will honor as it's own internal I/O maximum
transfer length limit, as exposed by EVPD=0xb0 block limits
parameters.
This is required for handling cases when host I/O transfer
length exceeds the requested EVPD block limits maximum
transfer length. The initial user of this logic is qla2xxx,
so that we can avoid having to reject I/Os from some legacy
FC hosts where EVPD=0xb0 parameters are not honored.
When se_cmd payload length exceeds the provided limit in
target_check_max_data_sg_nents() code, se_cmd->data_length +
se_cmd->prot_length are reset with se_cmd->residual_count
plus underflow bit for outgoing TFO response callbacks.
It also checks for existing CDB level underflow + overflow
and recalculates final residual_count as necessary.
Note this patch currently assumes 1:1 mapping of PAGE_SIZE
per struct scatterlist entry.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Cc: Craig Watson <craig.watson@vanguard-rugged.com>
Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dave Airlie [Fri, 11 Sep 2015 04:38:36 +0000 (14:38 +1000)]
Merge branch 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
three nouveau regression fixes.
* 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/device: enable c800 quirk for tecra w50
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
drm/nouveau/gr/nv04: fix big endian setting on gr context
Linus Torvalds [Fri, 11 Sep 2015 01:56:14 +0000 (18:56 -0700)]
Merge branch 'for-4.3/blkcg' of git://git.kernel.dk/linux-block
Pull blk-cg updates from Jens Axboe:
"A bit later in the cycle, but this has been in the block tree for a a
while. This is basically four patchsets from Tejun, that improve our
buffered cgroup writeback. It was dependent on the other cgroup
changes, but they went in earlier in this cycle.
Series 1 is set of 5 patches that has cgroup writeback updates:
- bdi_writeback iteration fix which could lead to some wb's being
skipped or repeated during e.g. sync under memory pressure.
- Simplification of wb work wait mechanism.
- Writeback tracepoints updated to report cgroup.
Series 2 is is a set of updates for the CFQ cgroup writeback handling:
cfq has always charged all async IOs to the root cgroup. It didn't
have much choice as writeback didn't know about cgroups and there
was no way to tell who to blame for a given writeback IO.
writeback finally grew support for cgroups and now tags each
writeback IO with the appropriate cgroup to charge it against.
This patchset updates cfq so that it follows the blkcg each bio is
tagged with. Async cfq_queues are now shared across cfq_group,
which is per-cgroup, instead of per-request_queue cfq_data. This
makes all IOs follow the weight based IO resource distribution
implemented by cfq.
- Switched from GFP_ATOMIC to GFP_NOWAIT as suggested by Jeff.
- Other misc review points addressed, acks added and rebased.
Series 3 is the blkcg policy cleanup patches:
This patchset contains assorted cleanups for blkcg_policy methods
and blk[c]g_policy_data handling.
- alloc/free added for blkg_policy_data. exit dropped.
- alloc/free added for blkcg_policy_data.
- blk-throttle's async percpu allocation is replaced with direct
allocation.
- all methods now take blk[c]g_policy_data instead of blkcg_gq or
blkcg.
And finally, series 4 is a set of patches cleaning up the blkcg stats
handling:
blkcg's stats have always been somwhat of a mess. This patchset
tries to improve the situation a bit.
- The following patches added to consolidate blkcg entry point and
blkg creation. This is in itself is an improvement and helps
colllecting common stats on bio issue.
- per-blkg stats now accounted on bio issue rather than request
completion so that bio based and request based drivers can behave
the same way. The issue was spotted by Vivek.
- cfq-iosched implements custom recursive stats and blk-throttle
implements custom per-cpu stats. This patchset make blkcg core
support both by default.
- cfq-iosched and blk-throttle keep track of the same stats
multiple times. Unify them"
* 'for-4.3/blkcg' of git://git.kernel.dk/linux-block: (45 commits)
blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchy
blkcg: s/CFQ_WEIGHT_*/CFQ_WEIGHT_LEGACY_*/
blkcg: implement interface for the unified hierarchy
blkcg: misc preparations for unified hierarchy interface
blkcg: separate out tg_conf_updated() from tg_set_conf()
blkcg: move body parsing from blkg_conf_prep() to its callers
blkcg: mark existing cftypes as legacy
blkcg: rename subsystem name from blkio to io
blkcg: refine error codes returned during blkcg configuration
blkcg: remove unnecessary NULL checks from __cfqg_set_weight_device()
blkcg: reduce stack usage of blkg_rwstat_recursive_sum()
blkcg: remove cfqg_stats->sectors
blkcg: move io_service_bytes and io_serviced stats into blkcg_gq
blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gq
blkcg: make blkcg_[rw]stat per-cpu
blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with it
blkcg: consolidate blkg creation in blkcg_bio_issue_check()
blk-throttle: improve queue bypass handling
blkcg: move root blkg lookup optimization from throtl_lookup_tg() to __blkg_lookup()
blkcg: inline [__]blkg_lookup()
...
Ben Skeggs [Thu, 3 Sep 2015 02:39:45 +0000 (12:39 +1000)]
drm/nouveau/device: enable c800 quirk for tecra w50
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Roy Spliet [Wed, 2 Sep 2015 22:21:02 +0000 (23:21 +0100)]
drm/nouveau/clk/gt215: Unbreak engine pausing for GT21x/MCP7x
Typo that snuck in with commit
6979c6303a4abf263753cd9d577d79f05c6e8c47
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Reported-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ilia Mirkin [Tue, 1 Sep 2015 02:50:28 +0000 (22:50 -0400)]
drm/nouveau/gr/nv04: fix big endian setting on gr context
Broken since "gr: convert user classes to new-style nvkm_object"
Tested on a PPC64 G5 + NV34
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Linus Torvalds [Fri, 11 Sep 2015 01:19:42 +0000 (18:19 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge third patch-bomb from Andrew Morton:
- even more of the rest of MM
- lib/ updates
- checkpatch updates
- small changes to a few scruffy filesystems
- kmod fixes/cleanups
- kexec updates
- a dma-mapping cleanup series from hch
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (81 commits)
dma-mapping: consolidate dma_set_mask
dma-mapping: consolidate dma_supported
dma-mapping: cosolidate dma_mapping_error
dma-mapping: consolidate dma_{alloc,free}_noncoherent
dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}
mm: use vma_is_anonymous() in create_huge_pmd() and wp_huge_pmd()
mm: make sure all file VMAs have ->vm_ops set
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
mm: mark most vm_operations_struct const
namei: fix warning while make xmldocs caused by namei.c
ipc: convert invalid scenarios to use WARN_ON
zlib_deflate/deftree: remove bi_reverse()
lib/decompress_unlzma: Do a NULL check for pointer
lib/decompressors: use real out buf size for gunzip with kernel
fs/affs: make root lookup from blkdev logical size
sysctl: fix int -> unsigned long assignments in INT_MIN case
kexec: export KERNEL_IMAGE_SIZE to vmcoreinfo
kexec: align crash_notes allocation to make it be inside one physical page
kexec: remove unnecessary test in kimage_alloc_crash_control_pages()
kexec: split kexec_load syscall from kexec core code
...
Linus Torvalds [Fri, 11 Sep 2015 00:59:04 +0000 (17:59 -0700)]
Merge tag 'armsoc-late' of git://git./linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
Dave Airlie [Fri, 11 Sep 2015 00:52:37 +0000 (10:52 +1000)]
Merge tag 'topic/drm-fixes-2015-09-09' of git://anongit.freedesktop.org/drm-intel into drm-next
bunch of drm fixes.
* tag 'topic/drm-fixes-2015-09-09' of git://anongit.freedesktop.org/drm-intel:
drm/dp: Add dp_aux_i2c_speed_khz module param to set the assume i2c bus speed
drm/dp: Adjust i2c-over-aux retry count based on message size and i2c bus speed
drm/dp: Define AUX_RETRY_INTERVAL as 500 us
drm/atomic: Fix bookkeeping with TEST_ONLY, v3.
Dave Airlie [Fri, 11 Sep 2015 00:52:08 +0000 (10:52 +1000)]
Merge tag 'drm-intel-next-fixes-2015-09-10' of git://anongit.freedesktop.org/drm-intel into drm-next
Fixes headed for v4.3-rc1, including Maarten's DP MST state checker fix
you requested.
* tag 'drm-intel-next-fixes-2015-09-10' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Allow DSI dual link to be configured on any pipe
drm/i915: Don't try to use DDR DVFS on CHV when disabled in the BIOS
drm/i915: Fix CSR MMIO address check
drm/i915: Limit the number of loops for reading a split 64bit register
drm/i915: Fix broken mst get_hw_state.
drm/i915: Pass hpd_status_i915[] to intel_get_hpd_pins() in pre-g4x
uapi/drm/i915_drm.h: fix userspace compilation.
drm/i915: Always mark the object as dirty when used by the GPU
Jonathon Jongsma [Thu, 20 Aug 2015 19:04:32 +0000 (14:04 -0500)]
drm/qxl: validate monitors config modes
Due to some recent changes in
drm_helper_probe_single_connector_modes_merge_bits(), old custom modes
were not being pruned properly. In current kernels,
drm_mode_validate_basic() is called to sanity-check each mode in the
list. If the sanity-check passes, the mode's status gets set to to
MODE_OK. In older kernels this check was not done, so old custom modes
would still have a status of MODE_UNVERIFIED at this point, and would
therefore be pruned later in the function.
As a result of this new behavior, the list of modes for a device always
includes every custom mode ever configured for the device, with the
largest one listed first. Since desktop environments usually choose the
first preferred mode when a hotplug event is emitted, this had the
result of making it very difficult for the user to reduce the size of
the display.
The qxl driver did implement the mode_valid connector function, but it
was empty. In order to restore the old behavior where old custom modes
are pruned, we implement a proper mode_valid function for the qxl
driver. This function now checks each mode against the last configured
custom mode and the list of standard modes. If the mode doesn't match
any of these, its status is set to MODE_BAD so that it will be pruned as
expected.
Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 10 Sep 2015 23:42:49 +0000 (16:42 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"ARM:
- Full debug support for arm64
- Active state switching for timer interrupts
- Lazy FP/SIMD save/restore for arm64
- Generic ARMv8 target
PPC:
- Book3S: A few bug fixes
- Book3S: Allow micro-threading on POWER8
x86:
- Compiler warnings
Generic:
- Adaptive polling for guest halt"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (49 commits)
kvm: irqchip: fix memory leak
kvm: move new trace event outside #ifdef CONFIG_KVM_ASYNC_PF
KVM: trace kvm_halt_poll_ns grow/shrink
KVM: dynamic halt-polling
KVM: make halt_poll_ns per-vCPU
Silence compiler warning in arch/x86/kvm/emulate.c
kvm: compile process_smi_save_seg_64() only for x86_64
KVM: x86: avoid uninitialized variable warning
KVM: PPC: Book3S: Fix typo in top comment about locking
KVM: PPC: Book3S: Fix size of the PSPB register
KVM: PPC: Book3S HV: Exit on H_DOORBELL if HOST_IPI is set
KVM: PPC: Book3S HV: Fix race in starting secondary threads
KVM: PPC: Book3S: correct width in XER handling
KVM: PPC: Book3S HV: Fix preempted vcore stolen time calculation
KVM: PPC: Book3S HV: Fix preempted vcore list locking
KVM: PPC: Book3S HV: Implement H_CLEAR_REF and H_CLEAR_MOD
KVM: PPC: Book3S HV: Fix bug in dirty page tracking
KVM: PPC: Book3S HV: Fix race in reading change bit when removing HPTE
KVM: PPC: Book3S HV: Implement dynamic micro-threading on POWER8
KVM: PPC: Book3S HV: Make use of unused threads when running guests
...
Linus Torvalds [Thu, 10 Sep 2015 23:21:11 +0000 (16:21 -0700)]
Merge tag 'for-linus-4.3-rc0b-tag' of git://git./linux/kernel/git/xen/tip
Pull xen terminology fixes from David Vrabel:
"Use the correct GFN/BFN terms more consistently"
* tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Rename the variable xen_store_mfn to xen_store_gfn
xen/privcmd: Further s/MFN/GFN/ clean-up
hvc/xen: Further s/MFN/GFN clean-up
video/xen-fbfront: Further s/MFN/GFN clean-up
xen/tmem: Use xen_page_to_gfn rather than pfn_to_gfn
xen: Use correctly the Xen memory terminologies
arm/xen: implement correctly pfn_to_mfn
xen: Make clear that swiotlb and biomerge are dealing with DMA address
Linus Torvalds [Thu, 10 Sep 2015 23:20:00 +0000 (16:20 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze update from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
elf-em.h: move EM_MICROBLAZE to the common header
Linus Torvalds [Thu, 10 Sep 2015 23:19:07 +0000 (16:19 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rkuo/linux-hexagon-kernel
Pull hexagon updates from Richard Kuo:
"Just two fixes -- one for a uapi header and one for a timer interface"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Revert "Hexagon: fix signal.c compile error"
hexagon/time: Migrate to new 'set-state' interface
Linus Torvalds [Thu, 10 Sep 2015 20:53:15 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix out-of-bounds array access in netfilter ipset, from Jozsef
Kadlecsik.
2) Use correct free operation on netfilter conntrack templates, from
Daniel Borkmann.
3) Fix route leak in SCTP, from Marcelo Ricardo Leitner.
4) Fix sizeof(pointer) in mac80211, from Thierry Reding.
5) Fix cache pointer comparison in ip6mr leading to missed unlock of
mrt_lock. From Richard Laing.
6) rds_conn_lookup() needs to consider network namespace in key
comparison, from Sowmini Varadhan.
7) Fix deadlock in TIPC code wrt broadcast link wakeups, from Kolmakov
Dmitriy.
8) Fix fd leaks in bpf syscall, from Daniel Borkmann.
9) Fix error recovery when installing ipv6 multipath routes, we would
delete the old route before we would know if we could fully commit
to the new set of nexthops. Fix from Roopa Prabhu.
10) Fix run-time suspend problems in r8152, from Hayes Wang.
11) In fec, don't program the MAC address into the chip when the clocks
are gated off. From Fugang Duan.
12) Fix poll behavior for netlink sockets when using rx ring mmap, from
Daniel Borkmann.
13) Don't allocate memory with GFP_KERNEL from get_stats64 in r8169
driver, from Corinna Vinschen.
14) In TCP Cubic congestion control, handle idle periods better where we
are application limited, in order to keep cwnd from growing out of
control. From Eric Dumzet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
tcp_cubic: better follow cubic curve after idle period
tcp: generate CA_EVENT_TX_START on data frames
xen-netfront: respect user provided max_queues
xen-netback: respect user provided max_queues
r8169: Fix sleeping function called during get_stats64, v2
ether: add IEEE 1722 ethertype - TSN
netlink, mmap: fix edge-case leakages in nf queue zero-copy
netlink, mmap: don't walk rx ring on poll if receive queue non-empty
cxgb4: changes for new firmware 1.14.4.0
net: fec: add netif status check before set mac address
r8152: fix the runtime suspend issues
r8152: split DRIVER_VERSION
ipv6: fix ifnullfree.cocci warnings
add microchip LAN88xx phy driver
stmmac: fix check for phydev being open
net: qlcnic: delete redundant memsets
net: mv643xx_eth: use kzalloc
net: jme: use kzalloc() instead of kmalloc+memset
net: cavium: liquidio: use kzalloc in setup_glist()
net: ipv6: use common fib_default_rule_pref
...
Christoph Hellwig [Wed, 9 Sep 2015 22:39:53 +0000 (15:39 -0700)]
dma-mapping: consolidate dma_set_mask
Almost everyone implements dma_set_mask the same way, although some time
that's hidden in ->set_dma_mask methods.
This patch consolidates those into a common implementation that either
calls ->set_dma_mask if present or otherwise uses the default
implementation. Some architectures used to only call ->set_dma_mask
after the initial checks, and those instance have been fixed to do the
full work. h8300 implemented dma_set_mask bogusly as a no-ops and has
been fixed.
Unfortunately some architectures overload unrelated semantics like changing
the dma_ops into it so we still need to allow for an architecture override
for now.
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Wed, 9 Sep 2015 22:39:49 +0000 (15:39 -0700)]
dma-mapping: consolidate dma_supported
Most architectures just call into ->dma_supported, but some also return 1
if the method is not present, or 0 if no dma ops are present (although
that should never happeb). Consolidate this more broad version into
common code.
Also fix h8300 which inorrectly always returned 0, which would have been
a problem if it's dma_set_mask implementation wasn't a similarly buggy
noop.
As a few architectures have much more elaborate implementations, we
still allow for arch overrides.
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Wed, 9 Sep 2015 22:39:46 +0000 (15:39 -0700)]
dma-mapping: cosolidate dma_mapping_error
Currently there are three valid implementations of dma_mapping_error:
(1) call ->mapping_error
(2) check for a hardcoded error code
(3) always return 0
This patch provides a common implementation that calls ->mapping_error
if present, then checks for DMA_ERROR_CODE if defined or otherwise
returns 0.
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Wed, 9 Sep 2015 22:39:42 +0000 (15:39 -0700)]
dma-mapping: consolidate dma_{alloc,free}_noncoherent
Most architectures do not support non-coherent allocations and either
define dma_{alloc,free}_noncoherent to their coherent versions or stub
them out.
Openrisc uses dma_{alloc,free}_attrs to implement them, and only Mips
implements them directly.
This patch moves the Openrisc version to common code, and handles the
DMA_ATTR_NON_CONSISTENT case in the mips dma_map_ops instance.
Note that actual non-coherent allocations require a dma_cache_sync
implementation, so if non-coherent allocations didn't work on
an architecture before this patch they still won't work after it.
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Wed, 9 Sep 2015 22:39:39 +0000 (15:39 -0700)]
dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}
Since 2009 we have a nice asm-generic header implementing lots of DMA API
functions for architectures using struct dma_map_ops, but unfortunately
it's still missing a lot of APIs that all architectures still have to
duplicate.
This series consolidates the remaining functions, although we still need
arch opt outs for two of them as a few architectures have very
non-standard implementations.
This patch (of 5):
The coherent DMA allocator works the same over all architectures supporting
dma_map operations.
This patch consolidates them and converges the minor differences:
- the debug_dma helpers are now called from all architectures, including
those that were previously missing them
- dma_alloc_from_coherent and dma_release_from_coherent are now always
called from the generic alloc/free routines instead of the ops
dma-mapping-common.h always includes dma-coherent.h to get the defintions
for them, or the stubs if the architecture doesn't support this feature
- checks for ->alloc / ->free presence are removed. There is only one
magic instead of dma_map_ops without them (mic_dma_ops) and that one
is x86 only anyway.
Besides that only x86 needs special treatment to replace a default devices
if none is passed and tweak the gfp_flags. An optional arch hook is provided
for that.
[linux@roeck-us.net: fix build]
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Wed, 9 Sep 2015 22:39:35 +0000 (15:39 -0700)]
mm: use vma_is_anonymous() in create_huge_pmd() and wp_huge_pmd()
Let's use helper rather than direct check of vma->vm_ops to distinguish
anonymous VMA.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Wed, 9 Sep 2015 22:39:32 +0000 (15:39 -0700)]
mm: make sure all file VMAs have ->vm_ops set
We rely on vma->vm_ops == NULL to detect anonymous VMA: see
vma_is_anonymous(), but some drivers doesn't set ->vm_ops.
As a result we can end up with anonymous page in private file mapping.
That should not lead to serious misbehaviour, but nevertheless is wrong.
Let's fix by setting up dummy ->vm_ops for file mmapping if f_op->mmap()
didn't set its own.
The patch also adds sanity check into __vma_link_rb(). It will help
catch broken VMAs which inserted directly into mm_struct via
insert_vm_struct().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 9 Sep 2015 22:39:29 +0000 (15:39 -0700)]
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
Add the additional "vm_flags_t vm_flags" argument to do_mmap_pgoff(),
rename it to do_mmap(), and re-introduce do_mmap_pgoff() as a simple
wrapper on top of do_mmap(). Perhaps we should update the callers of
do_mmap_pgoff() and kill it later.
This way mpx_mmap() can simply call do_mmap(vm_flags => VM_MPX) and do not
play with vm internals.
After this change mmap_region() has a single user outside of mmap.c,
arch/tile/mm/elf.c:arch_setup_additional_pages(). It would be nice to
change arch/tile/ and unexport mmap_region().
[kirill@shutemov.name: fix build]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Wed, 9 Sep 2015 22:39:26 +0000 (15:39 -0700)]
mm: mark most vm_operations_struct const
With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masanari Iida [Wed, 9 Sep 2015 22:39:23 +0000 (15:39 -0700)]
namei: fix warning while make xmldocs caused by namei.c
Fix the following warnings:
Warning(.//fs/namei.c:2422): No description found for parameter 'nd'
Warning(.//fs/namei.c:2422): Excess function parameter 'nameidata'
description in 'path_mountpoint'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davidlohr Bueso [Wed, 9 Sep 2015 22:39:20 +0000 (15:39 -0700)]
ipc: convert invalid scenarios to use WARN_ON
Considering Linus' past rants about the (ab)use of BUG in the kernel, I
took a look at how we deal with such calls in ipc. Given that any errors
or corruption in ipc code are most likely contained within the set of
processes participating in the broken mechanisms, there aren't really many
strong fatal system failure scenarios that would require a BUG call.
Also, if something is seriously wrong, ipc might not be the place for such
a BUG either.
1. For example, recently, a customer hit one of these BUG_ONs in shm
after failing shm_lock(). A busted ID imho does not merit a BUG_ON,
and WARN would have been better.
2. MSG_COPY functionality of posix msgrcv(2) for checkpoint/restore.
I don't see how we can hit this anyway -- at least it should be IS_ERR.
The 'copy' arg from do_msgrcv is always set by calling prepare_copy()
first and foremost. We could also probably drop this check altogether.
Either way, it does not merit a BUG_ON.
3. No ->fault() callback for the fs getting the corresponding page --
seems selfish to make the system unusable.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
yalin wang [Wed, 9 Sep 2015 22:39:18 +0000 (15:39 -0700)]
zlib_deflate/deftree: remove bi_reverse()
Remove bi_reverse() and use generic bitrev32() instead - it should have
better performance on some platforms.
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fabio Estevam [Wed, 9 Sep 2015 22:39:15 +0000 (15:39 -0700)]
lib/decompress_unlzma: Do a NULL check for pointer
Compare pointer-typed values to NULL rather than 0.
The semantic patch that makes this change is available
in scripts/coccinelle/null/badzero.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yinghai Lu [Wed, 9 Sep 2015 22:39:12 +0000 (15:39 -0700)]
lib/decompressors: use real out buf size for gunzip with kernel
When loading x86 64bit kernel above 4GiB with patched grub2, got kernel
gunzip error.
| early console in decompress_kernel
| decompress_kernel:
| input: [0x807f2143b4-0x807ff61aee]
| output: [0x807cc00000-0x807f3ea29b] 0x027ea29c: output_len
| boot via startup_64
| KASLR using RDTSC...
| new output: [0x46fe000000-0x470138cfff] 0x0338d000: output_run_size
| decompress: [0x46fe000000-0x47007ea29b] <=== [0x807f2143b4-0x807ff61aee]
|
| Decompressing Linux... gz...
|
| uncompression error
|
| -- System halted
the new buffer is at 0x46fe000000ULL, decompressor_gzip is using
0xffffffb901ffffff as out_len. gunzip in lib/zlib_inflate/inflate.c cap
that len to 0x01ffffff and decompress fails later.
We could hit this problem with crashkernel booting that uses kexec loading
kernel above 4GiB.
We have decompress_* support:
1. inbuf[]/outbuf[] for kernel preboot.
2. inbuf[]/flush() for initramfs
3. fill()/flush() for initrd.
This bug only affect kernel preboot path that use outbuf[].
Add __decompress and take real out_buf_len for gunzip instead of guessing
wrong buf size.
Fixes: 1431574a1c4 (lib/decompressors: fix "no limit" output buffer length)
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Jon Medhurst <tixy@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pranay Kr. Srivastava [Wed, 9 Sep 2015 22:39:09 +0000 (15:39 -0700)]
fs/affs: make root lookup from blkdev logical size
This patch resolves https://bugzilla.kernel.org/show_bug.cgi?id=16531.
When logical blkdev size > 512 then sector numbers become larger than the
device can support.
Make affs start lookup based on the device's logical sector size instead
of 512.
Reported-by: Mark <markk@clara.co.uk>
Suggested-by: Mark <markk@clara.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilya Dryomov [Wed, 9 Sep 2015 22:39:06 +0000 (15:39 -0700)]
sysctl: fix int -> unsigned long assignments in INT_MIN case
The following
if (val < 0)
*lvalp = (unsigned long)-val;
is incorrect because the compiler is free to assume -val to be positive
and use a sign-extend instruction for extending the bit pattern. This is
a problem if val == INT_MIN:
# echo -
2147483648 >/proc/sys/dev/scsi/logging_level
# cat /proc/sys/dev/scsi/logging_level
-
18446744071562067968
Cast to unsigned long before negation - that way we first sign-extend and
then negate an unsigned, which is well defined. With this:
# cat /proc/sys/dev/scsi/logging_level
-
2147483648
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Cc: Mikulas Patocka <mikulas@twibright.com>
Cc: Robert Xiao <nneonneo@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Baoquan He [Wed, 9 Sep 2015 22:39:03 +0000 (15:39 -0700)]
kexec: export KERNEL_IMAGE_SIZE to vmcoreinfo
In x86_64, since v2.6.26 the KERNEL_IMAGE_SIZE is changed to 512M, and
accordingly the MODULES_VADDR is changed to 0xffffffffa0000000. However,
in v3.12 Kees Cook introduced kaslr to randomise the location of kernel.
And the kernel text mapping addr space is enlarged from 512M to 1G. That
means now KERNEL_IMAGE_SIZE is variable, its value is 512M when kaslr
support is not compiled in and 1G when kaslr support is compiled in.
Accordingly the MODULES_VADDR is changed too to be:
#define MODULES_VADDR (__START_KERNEL_map + KERNEL_IMAGE_SIZE)
So when kaslr is compiled in and enabled, the kernel text mapping addr
space and modules vaddr space need be adjusted. Otherwise makedumpfile
will collapse since the addr for some symbols is not correct.
Hence KERNEL_IMAGE_SIZE need be exported to vmcoreinfo and got in
makedumpfile to help calculate MODULES_VADDR.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Baoquan He [Wed, 9 Sep 2015 22:39:00 +0000 (15:39 -0700)]
kexec: align crash_notes allocation to make it be inside one physical page
People reported that crash_notes in /proc/vmcore were corrupted and this
cause crash kdump failure. With code debugging and log we got the root
cause. This is because percpu variable crash_notes are allocated in 2
vmalloc pages. Currently percpu is based on vmalloc by default. Vmalloc
can't guarantee 2 continuous vmalloc pages are also on 2 continuous
physical pages. So when 1st kernel exports the starting address and size
of crash_notes through sysfs like below:
/sys/devices/system/cpu/cpux/crash_notes
/sys/devices/system/cpu/cpux/crash_notes_size
kdump kernel use them to get the content of crash_notes. However the 2nd
part may not be in the next neighbouring physical page as we expected if
crash_notes are allocated accross 2 vmalloc pages. That's why
nhdr_ptr->n_namesz or nhdr_ptr->n_descsz could be very huge in
update_note_header_size_elf64() and cause note header merging failure or
some warnings.
In this patch change to call __alloc_percpu() to passed in the align value
by rounding crash_notes_size up to the nearest power of two. This makes
sure the crash_notes is allocated inside one physical page since
sizeof(note_buf_t) in all ARCHS is smaller than PAGE_SIZE. Meanwhile add
a BUILD_BUG_ON to break compile if size is bigger than PAGE_SIZE since
crash_notes definitely will be in 2 pages. That need be avoided, and need
be reported if it's unavoidable.
[akpm@linux-foundation.org: use correct comment layout]
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minfei Huang [Wed, 9 Sep 2015 22:38:58 +0000 (15:38 -0700)]
kexec: remove unnecessary test in kimage_alloc_crash_control_pages()
Transforming PFN(Page Frame Number) to struct page is never failure, so we
can simplify the code logic to do the image->control_page assignment
directly in the loop, and remove the unnecessary conditional judgement.
Signed-off-by: Minfei Huang <mnfhuang@gmail.com>
Acked-by: Dave Young <dyoung@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Young [Wed, 9 Sep 2015 22:38:55 +0000 (15:38 -0700)]
kexec: split kexec_load syscall from kexec core code
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Young [Wed, 9 Sep 2015 22:38:51 +0000 (15:38 -0700)]
kexec: split kexec_file syscall code to kexec_file.c
Split kexec_file syscall related code to another file kernel/kexec_file.c
so that the #ifdef CONFIG_KEXEC_FILE in kexec.c can be dropped.
Sharing variables and functions are moved to kernel/kexec_internal.h per
suggestion from Vivek and Petr.
[akpm@linux-foundation.org: fix bisectability]
[akpm@linux-foundation.org: declare the various arch_kexec functions]
[akpm@linux-foundation.org: fix build]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Wed, 9 Sep 2015 22:38:48 +0000 (15:38 -0700)]
drivers/net/wireless/ath/wil6210: use seq_hex_dump() to dump buffers
Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Wed, 9 Sep 2015 22:38:45 +0000 (15:38 -0700)]
kmemleak: use seq_hex_dump() to dump buffers
Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Wed, 9 Sep 2015 22:38:42 +0000 (15:38 -0700)]
drivers/s390/crypto/zcrypt_api.c: use seq_hex_dump() to dump buffers
Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Wed, 9 Sep 2015 22:38:39 +0000 (15:38 -0700)]
parisc: use seq_hex_dump() to dump buffers
Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
In one case it changes the output from
1111111122222222333333334444444455555555666666667777777788888888
to
11111111 22222222 33333333 44444444 55555555 66666666 77777777 88888888
though it seems it prints same data (by meaning) in both cases. I decide
to choose to use the space divided one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Wed, 9 Sep 2015 22:38:36 +0000 (15:38 -0700)]
drivers/crypto/qat: use seq_hex_dump() to dump buffers
Instead of custom approach let's use recently introduced seq_hex_dump()
helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Wed, 9 Sep 2015 22:38:33 +0000 (15:38 -0700)]
seq_file: provide an analogue of print_hex_dump()
This introduces a new helper and switches current users to use it. All
patches are compiled tested. kmemleak is tested via its own test suite.
This patch (of 6):
The new seq_hex_dump() is a complete analogue of print_hex_dump().
We have few users of this functionality already. It allows to reduce their
codebase.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jann Horn [Wed, 9 Sep 2015 22:38:30 +0000 (15:38 -0700)]
fs: Don't dump core if the corefile would become world-readable.
On a filesystem like vfat, all files are created with the same owner
and mode independent of who created the file. When a vfat filesystem
is mounted with root as owner of all files and read access for everyone,
root's processes left world-readable coredumps on it (but other
users' processes only left empty corefiles when given write access
because of the uid mismatch).
Given that the old behavior was inconsistent and insecure, I don't see
a problem with changing it. Now, all processes refuse to dump core unless
the resulting corefile will only be readable by their owner.
Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jann Horn [Wed, 9 Sep 2015 22:38:28 +0000 (15:38 -0700)]
fs: if a coredump already exists, unlink and recreate with O_EXCL
It was possible for an attacking user to trick root (or another user) into
writing his coredumps into an attacker-readable, pre-existing file using
rename() or link(), causing the disclosure of secret data from the victim
process' virtual memory. Depending on the configuration, it was also
possible to trick root into overwriting system files with coredumps. Fix
that issue by never writing coredumps into existing files.
Requirements for the attack:
- The attack only applies if the victim's process has a nonzero
RLIMIT_CORE and is dumpable.
- The attacker can trick the victim into coredumping into an
attacker-writable directory D, either because the core_pattern is
relative and the victim's cwd is attacker-writable or because an
absolute core_pattern pointing to a world-writable directory is used.
- The attacker has one of these:
A: on a system with protected_hardlinks=0:
execute access to a folder containing a victim-owned,
attacker-readable file on the same partition as D, and the
victim-owned file will be deleted before the main part of the attack
takes place. (In practice, there are lots of files that fulfill
this condition, e.g. entries in Debian's /var/lib/dpkg/info/.)
This does not apply to most Linux systems because most distros set
protected_hardlinks=1.
B: on a system with protected_hardlinks=1:
execute access to a folder containing a victim-owned,
attacker-readable and attacker-writable file on the same partition
as D, and the victim-owned file will be deleted before the main part
of the attack takes place.
(This seems to be uncommon.)
C: on any system, independent of protected_hardlinks:
write access to a non-sticky folder containing a victim-owned,
attacker-readable file on the same partition as D
(This seems to be uncommon.)
The basic idea is that the attacker moves the victim-owned file to where
he expects the victim process to dump its core. The victim process dumps
its core into the existing file, and the attacker reads the coredump from
it.
If the attacker can't move the file because he does not have write access
to the containing directory, he can instead link the file to a directory
he controls, then wait for the original link to the file to be deleted
(because the kernel checks that the link count of the corefile is 1).
A less reliable variant that requires D to be non-sticky works with link()
and does not require deletion of the original link: link() the file into
D, but then unlink() it directly before the kernel performs the link count
check.
On systems with protected_hardlinks=0, this variant allows an attacker to
not only gain information from coredumps, but also clobber existing,
victim-writable files with coredumps. (This could theoretically lead to a
privilege escalation.)
Signed-off-by: Jann Horn <jann@thejh.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frederic Weisbecker [Wed, 9 Sep 2015 22:38:25 +0000 (15:38 -0700)]
kmod: handle UMH_WAIT_PROC from system unbound workqueue
The UMH_WAIT_PROC handler runs in its own thread in order to make sure
that waiting for the exec kernel thread completion won't block other
usermodehelper queued jobs.
On older workqueue implementations, worklets couldn't sleep without
blocking the rest of the queue. But now the workqueue subsystem handles
that. Khelper still had the older limitation due to its singlethread
properties but we replaced it to system unbound workqueues.
Those are affine to the current node and can block up to some number of
instances.
They are a good candidate to handle UMH_WAIT_PROC assuming that we have
enough system unbound workers to handle lots of parallel usermodehelper
jobs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frederic Weisbecker [Wed, 9 Sep 2015 22:38:22 +0000 (15:38 -0700)]
kmod: use system_unbound_wq instead of khelper
We need to launch the usermodehelper kernel threads with the widest
affinity and this is partly why we use khelper. This workqueue has
unbound properties and thus a wide affinity inherited by all its children.
Now khelper also has special properties that we aren't much interested in:
ordered and singlethread. There is really no need about ordering as all
we do is creating kernel threads. This can be done concurrently. And
singlethread is a useless limitation as well.
The workqueue engine already proposes generic unbound workqueues that
don't share these useless properties and handle well parallel jobs.
The only worrysome specific is their affinity to the node of the current
CPU. It's fine for creating the usermodehelper kernel threads but those
inherit this affinity for longer jobs such as requesting modules.
This patch proposes to use these node affine unbound workqueues assuming
that a node is sufficient to handle several parallel usermodehelper
requests.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frederic Weisbecker [Wed, 9 Sep 2015 22:38:19 +0000 (15:38 -0700)]
kmod: add up-to-date explanations on the purpose of each asynchronous levels
There seem to be quite some confusions on the comments, likely due to
changes that came after them.
Now since it's very non obvious why we have 3 levels of asynchronous code
to implement usermodehelpers, it's important to comment in detail the
reason of this layout.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frederic Weisbecker [Wed, 9 Sep 2015 22:38:16 +0000 (15:38 -0700)]
kmod: remove unecessary explicit wide CPU affinity setting
Khelper is affine to all CPUs. Now since it creates the
call_usermodehelper_exec_[a]sync() kernel threads, those inherit the wide
affinity.
As such explicitly forcing a wide affinity from those kernel threads
is like a no-op.
Just remove it. It's needless and it breaks CPU isolation users who
rely on workqueue affinity tuning.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frederic Weisbecker [Wed, 9 Sep 2015 22:38:13 +0000 (15:38 -0700)]
kmod: bunch of internal functions renames
This patchset does a bunch of cleanups and converts khelper to use system
unbound workqueues. The 3 first patches should be uncontroversial. The
last 2 patches are debatable.
Kmod creates kernel threads that perform userspace jobs and we want those
to have a large affinity in order not to contend busy CPUs. This is
(partly) why we use khelper which has a wide affinity that the kernel
threads it create can inherit from. Now khelper is a dedicated workqueue
that has singlethread properties which we aren't interested in.
Hence those two debatable changes:
_ We would like to use generic workqueues. System unbound workqueues are
a very good candidate but they are not wide affine, only node affine.
Now probably a node is enough to perform many parallel kmod jobs.
_ We would like to remove the wait_for_helper kernel thread (UMH_WAIT_PROC
handler) to use the workqueue. It means that if the workqueue blocks,
and no other worker can take pending kmod request, we can be screwed.
Now if we have 512 threads, this should be enough.
This patch (of 5):
Underscores on function names aren't much verbose to explain the purpose
of a function. And kmod has interesting such flavours.
Lets rename the following functions:
* __call_usermodehelper -> call_usermodehelper_exec_work
* ____call_usermodehelper -> call_usermodehelper_exec_async
* wait_for_helper -> call_usermodehelper_exec_sync
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 9 Sep 2015 22:38:10 +0000 (15:38 -0700)]
kmod: correct documentation of return status of request_module
If request_module() successfully runs modprobe, but modprobe exits with a
non-zero status, then the return value from request_module() will be that
(positive) error status. So the return from request_module can be:
negative errno
zero for success
positive exit code.
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hin-Tak Leung [Wed, 9 Sep 2015 22:38:07 +0000 (15:38 -0700)]
hfs: fix B-tree corruption after insertion at position 0
Fix B-tree corruption when a new record is inserted at position 0 in the
node in hfs_brec_insert().
This is an identical change to the corresponding hfs b-tree code to Sergei
Antonov's "hfsplus: fix B-tree corruption after insertion at position 0",
to keep similar code paths in the hfs and hfsplus drivers in sync, where
appropriate.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Sergei Antonov <saproj@gmail.com>
Cc: Joe Perches <joe@perches.com>
Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hin-Tak Leung [Wed, 9 Sep 2015 22:38:04 +0000 (15:38 -0700)]
hfs,hfsplus: cache pages correctly between bnode_create and bnode_free
Pages looked up by __hfs_bnode_create() (called by hfs_bnode_create() and
hfs_bnode_find() for finding or creating pages corresponding to an inode)
are immediately kmap()'ed and used (both read and write) and kunmap()'ed,
and should not be page_cache_release()'ed until hfs_bnode_free().
This patch fixes a problem I first saw in July 2012: merely running "du"
on a large hfsplus-mounted directory a few times on a reasonably loaded
system would get the hfsplus driver all confused and complaining about
B-tree inconsistencies, and generates a "BUG: Bad page state". Most
recently, I can generate this problem on up-to-date Fedora 22 with shipped
kernel 4.0.5, by running "du /" (="/" + "/home" + "/mnt" + other smaller
mounts) and "du /mnt" simultaneously on two windows, where /mnt is a
lightly-used QEMU VM image of the full Mac OS X 10.9:
$ df -i / /home /mnt
Filesystem Inodes IUsed IFree IUse% Mounted on
/dev/mapper/fedora-root
3276800 551665
2725135 17% /
/dev/mapper/fedora-home
52879360 716221
52163139 2% /home
/dev/nbd0p2
4294967295 1387818 4293579477 1% /mnt
After applying the patch, I was able to run "du /" (60+ times) and "du
/mnt" (150+ times) continuously and simultaneously for 6+ hours.
There are many reports of the hfsplus driver getting confused under load
and generating "BUG: Bad page state" or other similar issues over the
years. [1]
The unpatched code [2] has always been wrong since it entered the kernel
tree. The only reason why it gets away with it is that the
kmap/memcpy/kunmap follow very quickly after the page_cache_release() so
the kernel has not had a chance to reuse the memory for something else,
most of the time.
The current RW driver appears to have followed the design and development
of the earlier read-only hfsplus driver [3], where-by version 0.1 (Dec
2001) had a B-tree node-centric approach to
read_cache_page()/page_cache_release() per bnode_get()/bnode_put(),
migrating towards version 0.2 (June 2002) of caching and releasing pages
per inode extents. When the current RW code first entered the kernel [2]
in 2005, there was an REF_PAGES conditional (and "//" commented out code)
to switch between B-node centric paging to inode-centric paging. There
was a mistake with the direction of one of the REF_PAGES conditionals in
__hfs_bnode_create(). In a subsequent "remove debug code" commit [4], the
read_cache_page()/page_cache_release() per bnode_get()/bnode_put() were
removed, but a page_cache_release() was mistakenly left in (propagating
the "REF_PAGES <-> !REF_PAGE" mistake), and the commented-out
page_cache_release() in bnode_release() (which should be spanned by
!REF_PAGES) was never enabled.
References:
[1]:
Michael Fox, Apr 2013
http://www.spinics.net/lists/linux-fsdevel/msg63807.html
("hfsplus volume suddenly inaccessable after 'hfs: recoff %d too large'")
Sasha Levin, Feb 2015
http://lkml.org/lkml/2015/2/20/85 ("use after free")
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/740814
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/
1027887
https://bugzilla.kernel.org/show_bug.cgi?id=42342
https://bugzilla.kernel.org/show_bug.cgi?id=63841
https://bugzilla.kernel.org/show_bug.cgi?id=78761
[2]:
http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/\
fs/hfs/bnode.c?id=
d1081202f1d0ee35ab0beb490da4b65d4bc763db
commit
d1081202f1d0ee35ab0beb490da4b65d4bc763db
Author: Andrew Morton <akpm@osdl.org>
Date: Wed Feb 25 16:17:36 2004 -0800
[PATCH] HFS rewrite
http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/\
fs/hfsplus/bnode.c?id=
91556682e0bf004d98a529bf829d339abb98bbbd
commit
91556682e0bf004d98a529bf829d339abb98bbbd
Author: Andrew Morton <akpm@osdl.org>
Date: Wed Feb 25 16:17:48 2004 -0800
[PATCH] HFS+ support
[3]:
http://sourceforge.net/projects/linux-hfsplus/
http://sourceforge.net/projects/linux-hfsplus/files/Linux%202.4.x%20patch/hfsplus%200.1/
http://sourceforge.net/projects/linux-hfsplus/files/Linux%202.4.x%20patch/hfsplus%200.2/
http://linux-hfsplus.cvs.sourceforge.net/viewvc/linux-hfsplus/linux/\
fs/hfsplus/bnode.c?r1=1.4&r2=1.5
Date: Thu Jun 6 09:45:14 2002 +0000
Use buffer cache instead of page cache in bnode.c. Cache inode extents.
[4]:
http://git.kernel.org/cgit/linux/kernel/git/\
stable/linux-stable.git/commit/?id=
a5e3985fa014029eb6795664c704953720cc7f7d
commit
a5e3985fa014029eb6795664c704953720cc7f7d
Author: Roman Zippel <zippel@linux-m68k.org>
Date: Tue Sep 6 15:18:47 2005 -0700
[PATCH] hfs: remove debug code
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Anton Altaparmakov <anton@tuxera.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Sougata Santra <sougata@tuxera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Harkes [Wed, 9 Sep 2015 22:38:01 +0000 (15:38 -0700)]
fs/coda: fix readlink buffer overflow
Dan Carpenter discovered a buffer overflow in the Coda file system
readlink code. A userspace file system daemon can return a 4096 byte
result which then triggers a one byte write past the allocated readlink
result buffer.
This does not trigger with an unmodified Coda implementation because Coda
has a 1024 byte limit for symbolic links, however other userspace file
systems using the Coda kernel module could be affected.
Although this is an obvious overflow, I don't think this has to be handled
as too sensitive from a security perspective because the overflow is on
the Coda userspace daemon side which already needs root to open Coda's
kernel device and to mount the file system before we get to the point that
links can be read.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 9 Sep 2015 22:37:58 +0000 (15:37 -0700)]
checkpatch: add constant comparison on left side test
"CONST <comparison> variable" checks like:
if (NULL != foo)
and
while (0 < bar(...))
where a constant (or what appears to be a constant like an upper case
identifier) is on the left of a comparison are generally preferred to be
written using the constant on the right side like:
if (foo != NULL)
and
while (bar(...) > 0)
Add a test for this.
Add a --fix option too, but only do it when the code is immediately
surrounded by parentheses to avoid misfixing things like "(0 < bar() +
constant)"
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Nicolas Morey Chaisemartin <nmorey@kalray.eu>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 9 Sep 2015 22:37:55 +0000 (15:37 -0700)]
checkpatch: add __pmem to $Sparse annotations
commit
61031952f4c8 ("arch, x86: pmem api for ensuring durability of
persistent memory updates") added a new __pmem annotation for sparse
verification. Add __pmem to the $Sparse variable so checkpatch can
appropriately ignore uses of this attribute too.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eddie Kovsky [Wed, 9 Sep 2015 22:37:52 +0000 (15:37 -0700)]
checkpatch: fix left brace warning
Using checkpatch.pl with Perl 5.22.0 generates the following warning:
Unescaped left brace in regex is deprecated, passed through in regex;
This patch fixes the warnings by escaping occurrences of the left brace
inside the regular expression.
Signed-off-by: Eddie Kovsky <ewk@edkovsky.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / firefly-linux-kernel-4.4.55.git / log