Xinming Hu [Mon, 22 Jun 2015 13:36:13 +0000 (19:06 +0530)]
mwifiex: enable tdls channel switch ext_cap
This patch enable tdls channel switch ext capability in tdls action
frame, and also configure basic tdls channel switch parameters while
tdls setup completed and tdls link is enabled..
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Mon, 22 Jun 2015 13:36:12 +0000 (19:06 +0530)]
mwifiex: add tdls config command
This patch add support for a new tdls configuration command
which is used for configuration of tdls channel switch parameters.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Mon, 22 Jun 2015 13:36:11 +0000 (19:06 +0530)]
mwifiex: process tdls channel switch event
This patch add support for tdls channel switch event process.
We block TX queues for particular RA list depending upon channel
switch state. If channel switch state is moving to base channel,
we unblock RA lists for AP. If channel switch state is moving to off
channel, we unblock TDLS peer RA lists.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Mon, 22 Jun 2015 13:36:10 +0000 (19:06 +0530)]
mwifiex: add tdls channel switch status
This patch add new tdls status used for tdls channel switch.
Driver in turn would block cmd path and data path if tdls
channel switching. Data path to non tdls peer should be blocked
if tdls channel switch to off-channel.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Mon, 22 Jun 2015 13:36:09 +0000 (19:06 +0530)]
mwifiex: do not increase tx_pkts_queued if receive address tx paused
If tx_pkts_queued is increased for tx paused receive address, tx process
will be triggered for this packet. But since RA list was tx paused,
there will be an infinite loop in mwifiex_wmm_process_tx waiting for the
event(tx pause, tdls cs) to cancel tx pause. This will be an dead loop,
since main_process was locked at this time, there will be no opportunity
to process event.
So do not increase tx_pkts_queued if receive address tx paused,
this will be restored RA list is unpaused.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Mon, 22 Jun 2015 13:36:08 +0000 (19:06 +0530)]
mwifiex: block data traffic to tx paused receive address
Data traffic to tx paused receive address should be blocked.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Mon, 22 Jun 2015 13:36:07 +0000 (19:06 +0530)]
mwifiex: add tx data pause support
This patch adds support to enable TX data pause feature for mwifiex.
Whenever FW TX buffers reach threshold, FW would send TX pause event
to driver. Driver in turn would block data traffic to that particular
receiver address.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Fri, 19 Jun 2015 18:28:15 +0000 (03:28 +0900)]
rtlwifi: rtl8192cu: Remove rtl8723 code
In the rtlwifi/rtl8192cu, rtl8723 code is dead code.
So I remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Tue, 21 Jul 2015 08:36:56 +0000 (11:36 +0300)]
Merge ath-next from ath.git.
Major changes in ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
Zefir Kurtisi [Tue, 16 Jun 2015 10:52:16 +0000 (12:52 +0200)]
ath9k: DFS - add pulse chirp detection for FCC
FCC long pulse radar (type 5) requires pulses to be
checked for chirping. This patch implements chirp
detection based on the FFT data provided for long
pulses.
A chirp is detected when a set of criteria defined
by FCC pulse characteristics is met, including
* have at least 4 FFT samples
* max_bin index moves equidistantly between samples
* the gradient is within defined range
The chirp detection has been tested with reference
radar generating devices and proved to work reliably.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zefir Kurtisi [Tue, 16 Jun 2015 09:46:42 +0000 (11:46 +0200)]
ath9k: DFS - consider ext_channel pulses only in HT40 mode
The chip reports radar pulses on extension channel
even if operating in HT20 mode. This patch adds a
sanity check for HT40 mode before it feeds pulses
on extension channel to the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Nicholas Mc Guire [Mon, 15 Jun 2015 17:24:35 +0000 (19:24 +0200)]
ipw2100: fix timeout bug - always evaluated to 0
commit
2c86c275015c ("Add ipw2100 wireless driver.") introduced
HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified
by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50
milliseconds thus fixed up to msecs_to_jiffies(50).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Michal Kazior [Thu, 9 Jul 2015 11:08:39 +0000 (13:08 +0200)]
ath10k: tweak interface combinations
Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.
Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 9 Jul 2015 11:08:38 +0000 (13:08 +0200)]
ath10k: fix per-vif queue locking
Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.
This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.
Fixes: b4aa539dd8f2 ("ath10k: implement tx pause wmi event")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 9 Jul 2015 11:08:37 +0000 (13:08 +0200)]
ath10k: update vdev ps state on start
Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.
Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 9 Jul 2015 11:08:36 +0000 (13:08 +0200)]
ath10k: fix hw roc expiration notifcation
The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since
fcf9844636be ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.
This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 9 Jul 2015 11:08:35 +0000 (13:08 +0200)]
ath10k: limit multi-vif ps more aggresivelly
Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.
Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Thu, 9 Jul 2015 11:08:34 +0000 (13:08 +0200)]
ath10k: don't set cck/ofdm scan flags
mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan [Fri, 3 Jul 2015 13:55:27 +0000 (19:25 +0530)]
ath10k: Fix target to cpu address conversion logic
In commit
418ca5992e2f ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.
Fixes: 418ca5992e2f ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Bartosz Markowski [Fri, 3 Jul 2015 13:33:49 +0000 (15:33 +0200)]
ath10k: fix QCA61X4 boot up
commit
a521ee983d312db7 ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.
User experience was a failing boot up sequence (crashing device during
initialization):
[ 181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[ 181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[ 181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[ 181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70
Fix it by updating the address with correct value.
Fixes: a521ee983d31 ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
David S. Miller [Sat, 11 Jul 2015 06:24:31 +0000 (23:24 -0700)]
Merge branch 'be2net-next'
Sathya Perla says:
====================
be2net: patch set
Hi David, the following patch set has code cleanup patches, minor enhancements
and non-critical fixes. Pls consider applying to the net-next tree. Thanks!
Patch 1 removes duplicate code in be_setup_wol() routine making it simpler
and more readable.
Patch 2 fixes the the bridge mode return value for the ndo_bridge_getlink()
call. Instead of just relying on the SRIOV enabled state, the driver now
queries the FW, for the actual mode of bridge.
Patch 3 removes code for setting D0 power state as it's already done
in pci_enable_device()
Patch 4 fixes a bad return value in be_check_ufi_compatibility() routine
introduced by an earlier commit.
Patch 5 fixes a field in udp header being accessed while in network endian
format.
Patch 6 fixes the be_mcc_notify() routine to return an error status when
the FW/HW is in an error state.
Patch 7 fixes the be_cmd_rx_filter() routine to issue the RX_FILTER cmd
and not wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Patch 8 fixes the be_cmd_set_loopback() routine to issue the LOOPBACK cmd
and not wait for the FW completion while spin_lock_bh() is held on the
mcc_lock. As the cmd is always issued from ethtool in a process context,
it can sleep till the FW completion is received.
Patch 9 bumps up the driver version to 10.6.0.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Fri, 10 Jul 2015 09:32:51 +0000 (05:32 -0400)]
be2net: bump up the driver version to 10.6.0.3
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Fri, 10 Jul 2015 09:32:50 +0000 (05:32 -0400)]
be2net: make SET_LOOPBACK_MODE cmd asynchrounous
The SET_LOOPBACK_MODE command is always issued from ethtool only in a
process context. So, while waiting for the cmd to complete, the driver
can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done
by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns
only after the cmd completes while the MCCQ is locked).
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Fri, 10 Jul 2015 09:32:49 +0000 (05:32 -0400)]
be2net: make the RX_FILTER command asynchronous
This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues
this cmd and doesn't wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Fri, 10 Jul 2015 09:32:48 +0000 (05:32 -0400)]
be2net: return error status from be_mcc_notify()
When the adapter is in error state, return error from be_mcc_notify()
so that the caller routines need not sleep waiting for a response.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Venkat Duvvuru [Fri, 10 Jul 2015 09:32:47 +0000 (05:32 -0400)]
be2net: convert dest field in udp-hdr to host-endian
The "dest" field in the UDP-hdr of a TX skb is in network endian format.
Convert it to host endian before accessing it. The os2bmc patch,
mentioned below introduced this code.
Fixes: 760c295e0e8d ("be2net: Support for OS2BMC")
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 10 Jul 2015 09:32:46 +0000 (05:32 -0400)]
be2net: fix wrong return value in be_check_ufi_compatibility()
In the commit
a6e6ff6eee12f3e
("be2net: simplify UFI compatibility checking"), a return value of "-1"
was incorrectly used in place of "false". This patch fixes it.
Fixes: a6e6ff6eee12f3e ("be2net: simplify UFI compatibility checking")
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh Purayil [Fri, 10 Jul 2015 09:32:45 +0000 (05:32 -0400)]
be2net: remove redundant D0 power state set
pci_enable_device() call sets device power state to D0; there is no need
doing it again.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh Purayil [Fri, 10 Jul 2015 09:32:44 +0000 (05:32 -0400)]
be2net: query FW to check if EVB is enabled
The current code assumes that bridge functionality (EVB) in the adapter
is enabled only when SR-IOV is enabled. This is not always true.
This patch uses the GET_HSW_CONFIG FW cmd to query this from the FW.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh Purayil [Fri, 10 Jul 2015 09:32:43 +0000 (05:32 -0400)]
be2net: remove duplicate code in be_setup_wol()
This change will make be_setup_wol() routine more compact and readable
by removing some duplicate code.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YOSHIFUJI Hideaki/吉藤英明 [Fri, 10 Jul 2015 07:58:31 +0000 (16:58 +0900)]
ipv6: Do not iterate over all interfaces when finding source address on specific interface.
If outgoing interface is specified and the candidate address is
restricted to the outgoing interface, it is enough to iterate
over that given interface only.
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Kozlowski [Fri, 10 Jul 2015 06:29:23 +0000 (15:29 +0900)]
net: Drop owner assignment from platform_driver
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Thomson [Fri, 10 Jul 2015 04:28:25 +0000 (16:28 +1200)]
net: phy: Support setting polarity in marvell phy driver
Support manually setting the polarity to mdi or mdix
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Thomson [Fri, 10 Jul 2015 01:56:54 +0000 (13:56 +1200)]
net: phy: Pass mdix ethtool setting through to phy driver
Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Jul 2015 16:01:40 +0000 (18:01 +0200)]
tcp: do not export tcp_init_xmit_timers()
After commit
900f65d361d3 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()"), we no longer
need to export tcp_init_xmit_timers()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 9 Jul 2015 10:11:10 +0000 (03:11 -0700)]
bridge: mdb: fill state in br_mdb_notify
Fill also the port group state when sending notifications.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masatake YAMATO [Thu, 9 Jul 2015 03:46:35 +0000 (12:46 +0900)]
route: remove unsed variable in __mkroute_input
flags local variable in __mkroute_input is not used as a variable.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 8 Jul 2015 23:58:22 +0000 (16:58 -0700)]
ipv6: Nonlocal bind
Add support to allow non-local binds similar to how this was done for IPv4.
Non-local binds are very useful in emulating the Internet in a box, etc.
This add the ip_nonlocal_bind sysctl under ipv6.
Testing:
Set up nonlocal binding and receive routing on a host, e.g.:
ip -6 rule add from ::/0 iif eth0 lookup 200
ip -6 route add local 2001:0:0:1::/64 dev lo proto kernel scope host table 200
sysctl -w net.ipv6.ip_nonlocal_bind=1
Set up routing to 2001:0:0:1::/64 on peer to go to first host
ping6 -I 2001:0:0:1::1 peer-address -- to verify
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Jul 2015 22:12:21 +0000 (15:12 -0700)]
Merge branch 'tw_cleanups'
Eric Dumazet says:
====================
inet: timewait cleanups
Another round of patches to make tw handling simpler.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 8 Jul 2015 21:28:30 +0000 (14:28 -0700)]
inet: inet_twsk_deschedule factorization
inet_twsk_deschedule() calls are followed by inet_twsk_put().
Only particular case is in inet_twsk_purge() but there is no point
to defer the inet_twsk_put() after re-enabling BH.
Lets rename inet_twsk_deschedule() to inet_twsk_deschedule_put()
and move the inet_twsk_put() inside.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 8 Jul 2015 21:28:29 +0000 (14:28 -0700)]
inet: simplify timewait refcounting
timewait sockets have a complex refcounting logic.
Once we realize it should be similar to established and
syn_recv sockets, we can use sk_nulls_del_node_init_rcu()
and remove inet_twsk_unhash()
In particular, deferred inet_twsk_put() added in commit
13475a30b66cd ("tcp: connect() race with timewait reuse")
looks unecessary : When removing a timewait socket from
ehash or bhash, caller must own a reference on the socket
anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 8 Jul 2015 21:28:28 +0000 (14:28 -0700)]
inet: remove BUG_ON() in twsk_destructor()
Kernel will crash the same if one of the pointer is NULL anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 8 Jul 2015 21:32:12 +0000 (23:32 +0200)]
ipv6: use flag instead of u16 for hop in inet6_skb_parm
Hop was always either 0 or sizeof(struct ipv6hdr).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksey S. Kazantsev [Wed, 8 Jul 2015 03:38:15 +0000 (20:38 -0700)]
dsa: mv88e6352/mv88e6xxx: Add support for Marvell
88E6320 and
88E6321
MV88E6320 and MV88E6321 are largely compatible to MV886352,
but are members of a different chip family.
Signed-off-by: Aleksey S. Kazantsev <ioctl@yandex.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Jul 2015 21:22:53 +0000 (14:22 -0700)]
Merge branch 'tcp-in-slow-start'
Yuchung Cheng says:
====================
tcp: fixes some congestion control corner cases
This patch series fixes corner cases of TCP congestion control.
First issue is to avoid continuing slow start when cwnd reaches ssthresh.
Second issue is incorrectly processing order of congestion state and
cwnd update when entering fast recovery or undoing cwnd.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 9 Jul 2015 20:16:31 +0000 (13:16 -0700)]
tcp: update congestion state first before raising cwnd
The congestion state and cwnd can be updated in the wrong order.
For example, upon receiving a dubious ACK, we incorrectly raise
the cwnd first (tcp_may_raise_cwnd()/tcp_cong_avoid()) because
the state is still Open, then enter recovery state to reduce cwnd.
For another example, if the ACK indicates spurious timeout or
retransmits, we first revert the cwnd reduction and congestion
state back to Open state. But we don't raise the cwnd even though
the ACK does not indicate any congestion.
To fix this problem we should first call tcp_fastretrans_alert() to
process the dubious ACK and update the congestion state, then call
tcp_may_raise_cwnd() that raises cwnd based on the current state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 9 Jul 2015 20:16:30 +0000 (13:16 -0700)]
tcp: do not slow start when cwnd equals ssthresh
In the original design slow start is only used to raise cwnd
when cwnd is stricly below ssthresh. It makes little sense
to slow start when cwnd == ssthresh: especially
when hystart has set ssthresh in the initial ramp, or after
recovery when cwnd resets to ssthresh. Not doing so will
also help reduce the buffer bloat slightly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 9 Jul 2015 20:16:29 +0000 (13:16 -0700)]
tcp: add tcp_in_slow_start helper
Add a helper to test the slow start condition in various congestion
control modules and other places. This is to prepare a slight improvement
in policy as to exactly when to slow start.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 9 Jul 2015 18:02:52 +0000 (11:02 -0700)]
net: skb_defer_rx_timestamp should check for phydev before setting up classify
This change makes it so that the call skb_defer_rx_timestamp will first
check for a phydev before going in and manipulating the skb->data and
skb->len values. By doing this we can avoid unnecessary work on network
devices that don't support phydev. As a result we reduce the total
instruction count needed to process this on most devices.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maxwell [Wed, 8 Jul 2015 00:12:28 +0000 (10:12 +1000)]
tcp: v1 always send a quick ack when quickacks are enabled
V1 of this patch contains Eric Dumazet's suggestion to move the per
dst RTAX_QUICKACK check into tcp_in_quickack_mode(). Thanks Eric.
I ran some tests and after setting the "ip route change quickack 1"
knob there were still many delayed ACKs sent. This occured
because when icsk_ack.quick=0 the !icsk_ack.pingpong value is
subsequently ignored as tcp_in_quickack_mode() checks both these
values. The condition for a quick ack to trigger requires
that both icsk_ack.quick != 0 and icsk_ack.pingpong=0. Currently
only icsk_ack.pingpong is controlled by the knob. But the
icsk_ack.quick value changes dynamically depending on heuristics.
The crux of the matter is that delayed acks still cannot be entirely
disabled even with the RTAX_QUICKACK per dst knob enabled. This
patch ensures that a quick ack is always sent when the RTAX_QUICKACK
per dst knob is turned on.
The "ip route change quickack 1" knob was recently added to enable
quickacks. It was modeled around the TCP_QUICKACK setsockopt() option.
This issue is that even with "ip route change quickack 1" enabled
we still see delayed ACKs under some conditions. It would be nice
to be able to completely disable delayed ACKs.
Here is an example:
# netstat -s|grep dela
3 delayed acks sent
For all routes enable the knob
# ip route change quickack 1
Generate some traffic across a slow link and we still see the delayed
acks.
# netstat -s|grep dela
106 delayed acks sent
1 delayed acks further delayed because of locked socket
The issue is that both the "ip route change quickack 1" knob and
the TCP_QUICKACK option set the icsk_ack.pingpong variable to 0.
However at the business end in the __tcp_ack_snd_check() routine,
tcp_in_quickack_mode() checks that both icsk_ack.quick != 0
and icsk_ack.pingpong=0 in order to trigger a quickack. As
icsk_ack.quick is determined by heuristics it can be 0. When
that occurs the icsk_ack.pingpong value is ignored and a delayed
ACK is sent regardless.
This patch moves the RTAX_QUICKACK per dst check into the
tcp_in_quickack_mode() routine which ensures that a quickack is
always sent when the quickack knob is enabled for that dst.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Wed, 8 Jul 2015 23:06:47 +0000 (16:06 -0700)]
rocker: add change MTU support
Implement ndo_change_mtu: on MTU change, reallocate Rx ring bufs and signal
HW of new port MTU value.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vaishali Thakkar [Thu, 9 Jul 2015 04:55:39 +0000 (10:25 +0530)]
neterion: s2io: Use module_pci_driver
Use module_pci_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pci_register_driver(&x); }
@b depends on a@
identifier e, a.x;
statement S;
@@
-static e(...) {
-pci_unregister_driver(&x);
-DBG_PRINT(INIT_DBG,"S");
- }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pci_driver;
@@
-module_exit(e);
+module_pci_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Thu, 9 Jul 2015 09:25:46 +0000 (14:55 +0530)]
cxgb4vf: Fix check to use new User Doorbell mechanism
If we don't have access to the new User GTS (T5+), use the old doorbell
mechanism; otherwise use the new BAR2 mechanism.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xi Wang [Wed, 8 Jul 2015 21:00:56 +0000 (14:00 -0700)]
test_bpf: extend tests for 32-bit endianness conversion
Currently "ALU_END_FROM_BE 32" and "ALU_END_FROM_LE 32" do not test if
the upper bits of the result are zeros (the arm64 JIT had such bugs).
Extend the two tests to catch this.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jul 2015 23:13:55 +0000 (16:13 -0700)]
Merge branch 'cxgb4-t6'
Hariprasad Shenai says:
====================
Cleanup, T6 changes and register range update
This patch series adds the following:
Don't use entire L2T table, update register ranges for T6 adapter,
read stats for only available channels for T6 and enable cim_la dump for
T6 adapter also.
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 7 Jul 2015 16:19:21 +0000 (21:49 +0530)]
cxgb4: Enable cim_la dump to support T6
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 7 Jul 2015 16:19:20 +0000 (21:49 +0530)]
cxgb4: Read stats for only available channels
Updating the driver to read the stats of only available channels. T6 and
later has only 2 channels
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 7 Jul 2015 16:19:19 +0000 (21:49 +0530)]
cxgb4: Update register ranges for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Tue, 7 Jul 2015 16:19:18 +0000 (21:49 +0530)]
cxgb4: Don't use entire L2T table, use only its slice
The driver was retrieving the parameters for the bounds of its
slice of the L2T from the firmware and then throwing those away and
using the entire table. This corrects that problem.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vaishali Thakkar [Tue, 7 Jul 2015 07:02:54 +0000 (12:32 +0530)]
net: ec_bhf: Use module_pci_driver
Use module_pci_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pci_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pci_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pci_driver;
@@
-module_exit(e);
+module_pci_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Mon, 6 Jul 2015 21:11:37 +0000 (14:11 -0700)]
hv_netvsc: Add support to set MTU reservation from guest side
When packet encapsulation is in use, the MTU needs to be reduced for
headroom reservation.
The existing code takes the updated MTU value only from the host side.
But vSwitch extensions, such as Open vSwitch, require the flexibility
to change the MTU to different values from within a guest during the
lifecycle of a vNIC, when the encapsulation protocol is changed. The
patch supports this kind of MTU changes.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 20:05:28 +0000 (22:05 +0200)]
ifb: add multiqueue operation
Add multiqueue capabilities to ifb netdevice.
This removes last bottleneck for ingress when mq qdisc can be used
to shard load from multiple RX queues on physical device.
Tested:
# netem based setup, installed at receiver side
ETH=eth0
IFB=ifb10
EST="est 1sec 4sec" # Optional rate estimator
RTT_HALF=2ms
#REORDER=20us
#LOSS="loss 1"
TXQ=8
ip link add ifb10 numtxqueues $TXQ type ifb
ip link set dev $IFB up
tc qdisc add dev $ETH ingress 2>/dev/null
tc filter add dev $ETH parent ffff: \
protocol ip u32 match u32 0 0 flowid 1:1 \
action mirred egress redirect dev $IFB
tc qdisc del dev $IFB root 2>/dev/null
tc qdisc add dev $IFB root handle 1: mq
for i in `seq 1 $TXQ`
do
slot=$( printf %x $(( i )) )
tc qd add dev $IFB parent 1:$slot $EST netem \
limit 100000 delay $RTT_HALF $REORDER $LOSS
done
lpaa24:~# tc -s -d qd sh dev ifb10
qdisc mq 1: root
Sent
316544766 bytes
5265927 pkt (dropped 0, overlimits 0 requeues 0)
backlog 98880b 1648p requeues 0
qdisc netem 8002: parent 1:1 limit 100000 delay 2.0ms
Sent
39601416 bytes 658721 pkt (dropped 0, overlimits 0 requeues 0)
rate 38235Kbit 79657pps backlog 12240b 204p requeues 0
qdisc netem 8003: parent 1:2 limit 100000 delay 2.0ms
Sent
39472866 bytes 657227 pkt (dropped 0, overlimits 0 requeues 0)
rate 38234Kbit 79655pps backlog 10620b 176p requeues 0
qdisc netem 8004: parent 1:3 limit 100000 delay 2.0ms
Sent
39703417 bytes 659699 pkt (dropped 0, overlimits 0 requeues 0)
rate 38320Kbit 79831pps backlog 12780b 213p requeues 0
qdisc netem 8005: parent 1:4 limit 100000 delay 2.0ms
Sent
39565149 bytes 658011 pkt (dropped 0, overlimits 0 requeues 0)
rate 38174Kbit 79530pps backlog 11880b 198p requeues 0
qdisc netem 8006: parent 1:5 limit 100000 delay 2.0ms
Sent
39506078 bytes 657354 pkt (dropped 0, overlimits 0 requeues 0)
rate 38195Kbit 79571pps backlog 12480b 208p requeues 0
qdisc netem 8007: parent 1:6 limit 100000 delay 2.0ms
Sent
39675994 bytes 658849 pkt (dropped 0, overlimits 0 requeues 0)
rate 38323Kbit 79838pps backlog 12600b 210p requeues 0
qdisc netem 8008: parent 1:7 limit 100000 delay 2.0ms
Sent
39532042 bytes 658367 pkt (dropped 0, overlimits 0 requeues 0)
rate 38177Kbit 79536pps backlog 13140b 219p requeues 0
qdisc netem 8009: parent 1:8 limit 100000 delay 2.0ms
Sent
39488164 bytes 657705 pkt (dropped 0, overlimits 0 requeues 0)
rate 38192Kbit 79568pps backlog 13Kb 222p requeues 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Mon, 6 Jul 2015 17:08:34 +0000 (22:38 +0530)]
cxgb4: Add PCI device ids for few more T5 and T6 adapters
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carol Soto [Mon, 6 Jul 2015 14:20:19 +0000 (09:20 -0500)]
net/mlx4_core: Add extra check for total vfs for SRIOV
Add extra check for total vfs for SRIOV to check if that value is
bigger than total vfs in pci SRIOV capabalities. Fix a check and
print of the number of maximum vfs that hw can handle. Fix a check
and print of the number of maximum vfs per port that driver can handle.
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Holzheu [Mon, 6 Jul 2015 14:20:07 +0000 (16:20 +0200)]
samples: bpf: enable trace samples for s390x
The trace bpf samples do not compile on s390x because they use x86
specific fields from the "pt_regs" structure.
Fix this and access the fields via new PT_REGS macros.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Punnaiah Choudary Kalluri [Mon, 6 Jul 2015 04:32:53 +0000 (10:02 +0530)]
net: macb: Add SG support for Zynq SOC family
Enable SG support for Zynq SOC family devices.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li, Liang Z [Mon, 6 Jul 2015 00:42:56 +0000 (08:42 +0800)]
xen-netback: remove duplicated function definition
There are two duplicated xenvif_zerocopy_callback() definitions.
Remove one of them.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jul 2015 20:50:42 +0000 (13:50 -0700)]
Merge branch 'sch_act_lockless'
Eric Dumazet says:
====================
net_sched: act: lockless operation
As mentioned by Alexei last week in Budapest, it is a bit weird
to take a spinlock in order to drop a packet in a tc filter...
Lets add percpu infra for tc actions and use it for gact & mirred.
Before changes, my host with 8 RX queues was handling 5 Mpps with gact,
and more than 11 Mpps after.
Mirred change is not yet visible if ifb+qdisc is used, as ifb is
not yet multi queue enabled, but is a step forward.
====================
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:09 +0000 (05:18 -0700)]
net_sched: act_mirred: remove spinlock in fast path
Like act_gact, act_mirred can be lockless in packet processing
1) Use percpu stats
2) update lastuse only every clock tick to avoid false sharing
3) use rcu to protect tcfm_dev
4) Remove spinlock usage, as it is no longer needed.
Next step : add multi queue capability to ifb device
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:08 +0000 (05:18 -0700)]
net_sched: act_gact: remove spinlock in fast path
Final step for gact RCU operation :
1) Use percpu stats
2) update lastuse only every clock tick to avoid false sharing
3) Remove spinlock acquisition, as it is no longer needed.
Since this is the last contended lock in packet RX when tc gact is used,
this gives impressive gain.
My host with 8 RX queues was handling 5 Mpps before the patch,
and more than 11 Mpps after patch.
Tested:
On receiver :
dev=eth0
tc qdisc del dev $dev ingress 2>/dev/null
tc qdisc add dev $dev ingress
tc filter del dev $dev root pref 10 2>/dev/null
tc filter del dev $dev pref 10 2>/dev/null
tc filter add dev $dev est 1sec 4sec parent ffff: protocol ip prio 1 \
u32 match ip src 7.0.0.0/8 flowid 1:15 action drop
Sender sends packets flood from 7/8 network
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:07 +0000 (05:18 -0700)]
net_sched: act_gact: read tcfg_ptype once
Third step for gact RCU operation :
Following patch will get rid of spinlock protection,
so we need to read tcfg_ptype once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:06 +0000 (05:18 -0700)]
net_sched: act_gact: use a separate packet counters for gact_determ()
Second step for gact RCU operation :
We want to get rid of the spinlock protecting gact operations.
Stats (packets/bytes) will soon be per cpu.
gact_determ() would not work without a central packet counter,
so lets add it for this mode.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:05 +0000 (05:18 -0700)]
net_sched: act_gact: make tcfg_pval non zero
First step for gact RCU operation :
Instead of testing if tcfg_pval is zero or not, just make it 1.
No change in behavior, but slightly faster code.
The smp_rmb()/smp_wmb() barriers, while not strictly needed at this
stage are added for upcoming spinlock removal.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:04 +0000 (05:18 -0700)]
net: sched: add percpu stats to actions
Reuse existing percpu infrastructure John Fastabend added for qdisc.
This patch adds a new cpustats parameter to tcf_hash_create() and all
actions pass false, meaning this patch should have no effect yet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 6 Jul 2015 12:18:03 +0000 (05:18 -0700)]
net: sched: extend percpu stats helpers
qdisc_bstats_update_cpu() and other helpers were added to support
percpu stats for qdisc.
We want to add percpu stats for tc action, so this patch add common
helpers.
qdisc_bstats_update_cpu() is renamed to qdisc_bstats_cpu_update()
qdisc_qstats_drop_cpu() is renamed to qdisc_qstats_cpu_drop()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 2 Jul 2015 11:24:44 +0000 (13:24 +0200)]
mlx4: TCP/UDP packets have L4 hash
Mellanox driver has the knowledge if rxhash is a L4 hash,
if it receives a non fragmented TCP or UDP frame and
NETIF_F_RXCSUM is enabled on netdev.
ip_summed value is CHECKSUM_UNNECESSARY in this case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Ido Shamay <idos@mellanox.com>
Acked-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Jul 2015 20:29:46 +0000 (13:29 -0700)]
Merge branch 'tcp-policer-drops'
Yuchung Cheng says:
====================
tcp: reducing lost retransmits in recovery
This patch series reduces lost retransmits in recovery, in particular
when dealing with traffic policers. The main problem is that
slow start in recovery under policing can cause massive lost and
retransmit storms: any excess sending rate turns into drops. The
solution is to avoid doing slow start when lost retransmit is
detected and use packet conservation instead.
On networks with traffic policers the patches have lowered the
TCP loss rates by ~20% from Google servers without latency regressions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Wed, 1 Jul 2015 21:11:15 +0000 (14:11 -0700)]
tcp: PRR uses CRB mode by default and SS mode conditionally
PRR slow start is often too aggressive especially when drops are
caused by traffic policers. The policers mainly use token bucket
to enforce the rate so sending (twice) faster than the delivery
rate causes excessive drops.
This patch changes PRR to the conservative reduction bound
(CRB) mode in RFC 6937 by default. CRB follows the packet
conservation rule to send at most the delivery rate by default.
But if many packets are lost and the pipe is empty, CRB may take N
round trips to repair N losses. We conditionally turn on slow start
mode if all these conditions are made to speed up the recovery:
1) on the second round or later in recovery
2) retransmission sent in the previous round is delivered on this ACK
3) no retransmission is marked lost on this ACK
By using packet conservation by default, this change reduces the loss
retransmits signicantly on networks that deploy traffic policers,
up to 20% reduction of overall loss rate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Wed, 1 Jul 2015 21:11:14 +0000 (14:11 -0700)]
tcp: reduce cwnd if retransmit is lost in CA_Loss
If the retransmission in CA_Loss is lost again, we should not
continue to slow start or raise cwnd in congestion avoidance mode.
Instead we should enter fast recovery and use PRR to reduce cwnd,
following the principle in RFC5681:
"... or the loss of a retransmission, should be taken as two
indications of congestion and, therefore, cwnd (and ssthresh) MUST
be lowered twice in this case."
This is especially important to reduce loss when the CA_Loss
state was caused by a traffic policer dropping the entire inflight.
The CA_Loss state has a problem where a loss of L packets causes the
sender to send a burst of L packets. So a policer that's dropping
most packets in a given RTT can cause a huge retransmit storm. By
contrast, PRR includes logic to bound the number of outbound packets
that result from a given ACK. So switching to CA_Recovery on lost
retransmits in CA_Loss avoids this retransmit storm problem when
in CA_Loss.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 3 Jul 2015 10:40:51 +0000 (16:10 +0530)]
cxgb4: Fix incorrect sequence numbers shown in devlog
Part of commit
49aa284fe64c4c1 ("cxgb4: Add support for devlog")
change introduced a real bug where the Device Log Sequence Numbers are
no longer being converted from firmware Big-Endian to local CPU-Endian
format.
This patch moves all of the translation into the devlog_show() routine.
The only endianness code now in devlog_open() is the small loop to find the
earliest (lowest Sequence Number) Device Log entry in the circular buffer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Angga [Fri, 3 Jul 2015 02:40:52 +0000 (14:40 +1200)]
ipv6: Make MLD packets to only be processed locally
Before commit
daad151263cf ("ipv6: Make ipv6_is_mld() inline and use it
from ip6_mc_input().") MLD packets were only processed locally. After the
change, a copy of MLD packet goes through ip6_mr_input, causing
MRT6MSG_NOCACHE message to be generated to user space.
Make MLD packet only processed locally.
Fixes: daad151263cf ("ipv6: Make ipv6_is_mld() inline and use it from ip6_mc_input().")
Signed-off-by: Hermin Anggawijaya <hermin.anggawijaya@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Thu, 2 Jul 2015 16:38:12 +0000 (18:38 +0200)]
netlink: Delete an unnecessary check before the function call "module_put"
The module_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Thu, 2 Jul 2015 15:58:21 +0000 (17:58 +0200)]
net-RDS: Delete an unnecessary check before the function call "module_put"
The module_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Thu, 2 Jul 2015 14:30:24 +0000 (16:30 +0200)]
net-ipv6: Delete an unnecessary check before the function call "free_percpu"
The free_percpu() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 2 Jul 2015 12:48:17 +0000 (05:48 -0700)]
bridge: vlan: fix usage of vlan 0 and 4095 again
Vlan ids 0 and 4095 were disallowed by commit:
8adff41c3d25 ("bridge: Don't use VID 0 and 4095 in vlan filtering")
but then the check was removed when vlan ranges were introduced by:
bdced7ef7838 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
So reintroduce the vlan range check.
Before patch:
[root@testvm ~]# bridge vlan add vid 0 dev eth0 master
(succeeds)
After Patch:
[root@testvm ~]# bridge vlan add vid 0 dev eth0 master
RTNETLINK answers: Invalid argument
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: bdced7ef7838 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Jul 2015 19:17:11 +0000 (12:17 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-07-02
A couple of regressions crept in because of a patch to use proper list
APIs rather than manually reading & writing the next/prev pointers
(commit
835a6a2f8603237a3e6cded5a6765090ecb06ea5). Turns out this was
masking a few bugs: a missing INIT_LIST_HEAD() call and incorrectly
using list_del() rather than list_del_init(). The two patches in this
set fix these, and it'd be nice they could still make it to 4.2-rc1 to
avoid new bug reports from users.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan [Wed, 1 Jul 2015 08:51:57 +0000 (14:21 +0530)]
enic: fix issues in enic_poll
In enic_poll, we clean tx and rx queues, when low latency busy socket polling
is happening, enic_poll will only clean tx queue. After cleaning tx, it should
return total budget for re-poll.
There is a small window between vnic_intr_unmask() and enic_poll_unlock_napi().
In this window if an irq occurs and napi is scheduled on different cpu, it tries
to acquire enic_poll_lock_napi() and fails. Unlock napi_poll before unmasking
the interrupt.
v2:
Do not change tx wonk done behaviour. Consider only rx work done for completing
napi.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 2 Jul 2015 18:07:27 +0000 (11:07 -0700)]
Merge tag 'module-misc-v4.1-rc8' of git://git./linux/kernel/git/paulg/linux
Pull init.h/module.h fragility fixes from Paul Gortmaker:
"Fixup various init.h misuses that are fragile wrt code moving to
module.h
What started as a removal of no longer required include <linux/init.h>
due to the earlier __cpuinit and __devinit removal led to the
observation that some module specfic support was living in init.h
itself, thus preventing the full removal from introducing compile
regressions.
This series includes a few final fixups needed prior to the relocation
of the modular init code from <init.h> to <module.h>. These are
things that weren't easily categorized into any of the other previous
series categories already requested for pull.
That said, each fixup branch (including this one) is independent and
there are no ordering constraints. Only the final code relocation
(which is NOT in this pull) requires that all my cleanup branches be
merged first"
* tag 'module-misc-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
tile: add init.h to usb.c to avoid compile failure
arm: fix implicit #include <linux/init.h> in entry asm.
x86: replace __init_or_module with __init in non-modular vsmp_64.c
Linus Torvalds [Thu, 2 Jul 2015 17:42:13 +0000 (10:42 -0700)]
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git./linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
Linus Torvalds [Thu, 2 Jul 2015 17:36:29 +0000 (10:36 -0700)]
Merge tag 'module_init-alternate_initcall-v4.1-rc8' of git://git./linux/kernel/git/paulg/linux
Pull module_init replacement part two from Paul Gortmaker:
"Replace module_init with appropriate alternate initcall in non
modules.
This series converts non-modular code that is using the module_init()
call to hook itself into the system to instead use one of our
alternate priority initcalls.
Unlike the previous series that used device_initcall and hence was a
runtime no-op, these commits change to one of the alternate initcalls,
because (a) we have them and (b) it seems like the right thing to do.
For example, it would seem logical to use arch_initcall for arch
specific setup code and fs_initcall for filesystem setup code.
This does mean however, that changes in the init ordering will be
taking place, and so there is a small risk that some kind of implicit
init ordering issue may lie uncovered. But I think it is still better
to give these ones sensible priorities than to just assign them all to
device_initcall in order to exactly preserve the old ordering.
Thad said, we have already made similar changes in core kernel code in
commit
c96d6660dc65 ("kernel: audit/fix non-modular users of
module_init in core code") without any regressions reported, so this
type of change isn't without precedent. It has also got the same
local testing and linux-next coverage as all the other pull requests
that I'm sending for this merge window have got.
Once again, there is an unused module_exit function removal that shows
up as an outlier upon casual inspection of the diffstat"
* tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling
x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling
mm/page_owner.c: use late_initcall to hook in enabling
lib/list_sort: use late_initcall to hook in self tests
arm: use subsys_initcall in non-modular pl320 IPC code
powerpc: don't use module_init for non-modular core hugetlb code
powerpc: use subsys_initcall for Freescale Local Bus
x86: don't use module_init for non-modular core bootflag code
netfilter: don't use module_init/exit in core IPV4 code
fs/notify: don't use module_init for non-modular inotify_user code
mm: replace module_init usages with subsys_initcall in nommu.c
Linus Torvalds [Thu, 2 Jul 2015 17:30:48 +0000 (10:30 -0700)]
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git./linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
Linus Torvalds [Thu, 2 Jul 2015 17:25:22 +0000 (10:25 -0700)]
Merge tag 'module-implicit-v4.1-rc8' of git://git./linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
Linus Torvalds [Thu, 2 Jul 2015 16:54:14 +0000 (09:54 -0700)]
Merge tag 'cpuinit-v4.1-rc8' of git://git./linux/kernel/git/paulg/linux
Pull __cpuinit removal from Paul Gortmaker:
"Remove __cpuinit macros and users.
We removed the __cpuinit stuff in 3.11-rc1 with commit
22f0a2736774
("init.h: remove __cpuinit sections from the kernel") but we left some
no-op stubs as a courtesy to unmerged code.
Here we get rid of the stubs as well, since (as can be seen in these
changes) they are enabling use cases to sneak back in, primarily from
older BSP code that has been living out of tree for some time prior to
getting mainlined. So we get rid of these "new" users 1st and then
get rid of the stubs.
Obviously, getting rid of the stubs can't happen until all the users
are gone, so I had to keep this together as a series, even though some
of these commits since got picked up into maintainers trees as well.
The nature of this change is such that it should have zero impact on
the generated runtime.
This is one of several independent cleanup branches aimed at enabling
better organization in the init.h and module.h code. They have been
getting coverage in the linux-next tree for the last month, in
addition to my local testing, which also covers approximately a half
dozen or more architectures"
* tag 'cpuinit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
init: delete the __cpuinit related stubs
kernel/cpu.c: remove new instance of __cpuinit that crept back in
sched/core: remove __cpuinit section tag that crept back in.
mips/mm/tlbex: remove new instance of __cpuinit that crept back in
mips/c-r4k: remove legacy __cpuinit section that crept in
mips/bcm77xx: remove legacy __cpuinit sections that crept in
mips/ath25: remove legacy __cpuinit section that crept in
arm/mach-hisi: remove legacy __CPUINIT section that crept in
arm/mach-rockchip: remove legacy __cpuinit section that crept in
arm/mach-mvebu: remove legacy __cpuinit sections that crept in
arm/mach-keystone: remove legacy __cpuinit sections that crept in
Raja Mani [Mon, 22 Jun 2015 14:52:27 +0000 (20:22 +0530)]
ath10k: configure frag desc memory to target for qca99X0
Pre qca99X0 chipsets follows the model where dynamically allocate
memory for frag desc on getting new skb for TX. But, this is not
going to be the case in qca99X0. It expects frag desc memory to be
allocated at boot time and let the driver to reuse allocated memory
after every TX completion. So there won't be any dynamic frag memory
memory allocation in qca99X0 during data transmission.
qca99X0 hardware doesn't need fragment desc address to be programmed
in msdu descriptor for every data transaction. It needs to know only
starting address of fragment descriptor at the time of the boot.
During data transmission, qca99X0 hardware can retrieve corresponding
frag addr by adding programmed frag desc base addr + msdu id.
Allocate continuous fragment descriptor memory (same size as number of
descriptor) at the time of target initialization and configure allocated
dma address to the target via HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG.
How this is allocated continuous memory is going to be used is not
covered in this patch. It just allocates memory and hand over to firmware.
If we don't do it at init time, qca99X0 will stall when firmware tries
to do TX.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 22 Jun 2015 14:52:26 +0000 (20:22 +0530)]
ath10k: set max spatial stream to 4 for 10.4 fw
10.4 fw supports upto 4 spatial stream. Limit max spatial
stream to 4 for 10.4 firmware and to 3 for non 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 22 Jun 2015 14:52:25 +0000 (20:22 +0530)]
ath10k: advertise 10.4 fw ap and sta iface combination to mac80211
10.4 fw supports upto 16 interface in ap mode and 1 interface
in station mode, overall total interfaces supported are 16
interfaces. Populate this limit in wiphy->iface_combinations.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 22 Jun 2015 14:52:24 +0000 (20:22 +0530)]
ath10k: add 10.4 fw specific htt msg definitions
New htt event table is added for 10.4 firmware. Following new htt
events are available only 10.4. adding this to generic htt event
table,
HTT_T2H_MSG_TYPE_EN_STATS,
HTT_T2H_MSG_TYPE_TX_FETCH_IND,
HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 22 Jun 2015 14:52:23 +0000 (20:22 +0530)]
ath10k: add scan support for 10.4 fw
Existing non 10.4 firmware scan related events and commands are
matching with 10.4 firmware (except chan info event). Link general
start scan,stop scan, scan channel list configuration functions
to 10.4 wmi function table and add a new handler to parse 10.4
specific chan info event.
10.4 firmware has extra scan completion reason
WMI_SCAN_REASON_INTERNAL_FAILURE and new scan event
WMI_SCAN_EVENT_FOREIGN_CHANNEL_EXIT compared to previous firmware
versions. These things are added in respective enum.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 22 Jun 2015 14:52:22 +0000 (20:22 +0530)]
ath10k: enable vdev and peer related operations for 10.4 fw
Most of existing vdev and peer related functions (vdev create,
vdev delete, vdev start, peer create, peer delete, peer flush, etc)
are reusable for 10.4 firmware. Link those general vdev and peer
functions to 10.4 wmi function table.
Existing general pktlog enable/disable, dbglog configuration functions
are reusable for 10.4 and add them also in wmi function table.
Also handle few wmi events (sevice rdy, echo, dbg msg, tbtt offset
update, dbg print) in ath10k_wmi_10_4_op_rx(). wow event is not
applicable in 10.4 firmware, have it under not implemented print.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 22 Jun 2015 14:52:21 +0000 (20:22 +0530)]
ath10k: handle 10.4 firmware wmi swba event
10.4 firmware swba event payload has space to accommodate upto
512 client traffic indication info & one p2p noa descriptor.
It's is not matching with exiting swba event format defined for
non 10.4 firmware. Non 10.4 firmware swba event format is designed
to support only upto only 128 client and four p2p notice of absence
descriptor.
following changes are done in this patch to enable ath10k to handle
10.4 firmware swba event,
- link generic ath10k_wmi_event_host_swba() to handle 10.4 swba
event in 10.4 wmi rx handler.
- add 10.4 specific swba event structure wmi_10_4_host_swba_event.
- new function ath10k_wmi_10_4_op_pull_swba_ev() to parse
10.4 swba event.
- increase tim_bitmap[] size in ath10k_vif to 64 to hold 512 station
power save state.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>