tdfxfb: make use of DDC information about connected monitor

Read DDC information from a connected monitor and use it to select initial
mode (if the mode is not specified).

Also, use the information to protect against modes outside the monitor
specs.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tdfxfb: move I2C functionality into the tdfxfb

The I2C functionality provided by the i2c-voodoo3 driver is moved into the
tdfxfb (frame buffer driver for Voodoo3 cards).  This way there is no
conflict between the i2c driver and the fb driver.

The tdfxfb does not make use from the DDC functionality yet but provides
all the functionality of the i2c-voodoo3 driver.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: support kretprobe and jprobe per-probe disabling

Add disable/enable_kretprobe() and disable/enable_jprobe().

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: support per-kprobe disabling

Add disable_kprobe() and enable_kprobe() to disable/enable kprobes
temporarily.

disable_kprobe() asynchronously disables probe handlers of specified
kprobe.  So, after calling it, some handlers can be called at a while.
enable_kprobe() enables specified kprobe.

aggr_pre_handler and aggr_post_handler check disabled probes.  On the
other hand aggr_break_handler and aggr_fault_handler don't check it
because these handlers will be called while executing pre or post handlers
and usually those help error handling.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: rename kprobe_enabled to kprobes_all_disarmed

Rename kprobe_enabled to kprobes_all_disarmed and invert logic due to
avoiding naming confusion from per-probe disabling.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: cleanup comment style in kprobes.h

Fix comment style in kprobes.h.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: move EXPORT_SYMBOL_GPL just after function definitions

Clean up positions of EXPORT_SYMBOL_GPL in kernel/kprobes.c according to
checkpatch.pl.

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kprobes: cleanup aggr_kprobe related code

Currently, kprobes can disable all probes at once, but can't disable it
individually (not unregister, just disable an kprobe, because
unregistering needs to wait for scheduler synchronization).  These patches
introduce APIs for on-the-fly per-probe disabling and re-enabling by
dis-arming/re-arming its breakpoint instruction.

This patch:

Change old_p to ap in add_new_kprobe() for readability, copy flags member
in add_aggr_kprobe(), and simplify the code flow of
register_aggr_kprobe().

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_imx: set spi_master.dma_alignment = 4

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pxa2xx_spi: set spi_master.dma_alignment = 8

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

SPI: add dma_alignment field to spi_master

Some SPI controllers have restrictions on DMAable buffers alignemt.
Currently if the buffer supplied by protocol driver is not properly
aligned, the controller silently performs transfer in PIO mode.  Addition
of dma_alignment field to spi_master allows protocol drivers to perform
proper alignment.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi_bfin5xx: remove unused IS_DMA_ALIGNED macro

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: pxa2xx_spi: introduce chipselect GPIO to simplify the common cases

Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

spi: limit reaches -1, tested 0

With a postfix decrement limit will reach -1 rather than 0, so the warning
will not be issued.

Also, add a cpu_relax() into the busy-wait loop.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mariusz Ceier <mceier@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: Make mmc_spi driver work on Blackfin

1. Rewrite of the non-dma data transfer functions to use only ONE mode
   of TIMOD (TIMOD=0x1).  With TIMOD=0, it was not possible to set the TX
   bit pattern.  So the TDBR = 0xFFFF inside the read calls won't work.

2. Clear SPI_RDBR before reading and before duplex transfer.
   Otherwise the garbage data in RDBR will get read.  Since mmc_spi uses a
   lot of duplex transfers, this is the main cause of mmc_spi failure.

3. Poll RXS for transfer completion.  Polling SPIF or TXS cannot
   guarantee transfer completion.  This may interrupt a transfer before it
   is finished.  Also this may leave garbage data in buffer and affect
   next transfer.

[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: Add GPIO controlled SPI Slave Select support

Add support for GPIO controlled SPI Chip Selects.  To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.

struct spi_board_info
        .chip_select = 0

struct bfin5xx_spi_chip
        .cs_gpio = GPIO_P###

There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer.  Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: fix NULL pointer crash

Fix NULL pointer crash when cleaning up from invalid platform resources

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: use bfin_spi_ prefix on all functions

Do this because when things crash, we get simple names like "setup" and
"start_queue" which is pretty difficult to trace back to the real thing:
the spi driver

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: fix bug - correct usage of struct spi_transfer.cs_change

According to comments in linux/spi/spi.h:

 * All SPI transfers start with the relevant chipselect active.  Normally
 * it stays selected until after the last transfer in a message. Drivers
 * can affect the chipselect signal using cs_change.
 *
 * (i) If the transfer isn't the last one in the message, this flag is
 * used to make the chipselect briefly go inactive in the middle of the
 * message.  Toggling chipselect in this way may be needed to terminate
 * a chip command, letting a single spi_message perform all of group of
 * chip transactions together.
 *
 * (ii) When the transfer is the last one in the message, the chip may
 * stay selected until the next transfer.  On multi-device SPI busses
 * with nothing blocking messages going to other devices, this is just
 * a performance hint; starting a message to another device deselects
 * this one.  But in other cases, this can be used to ensure correctness.
 * Some devices need protocol transactions to be built from a series of
 * spi_message submissions, where the content of one message is determined
 * by the results of previous messages and where the whole transaction
 * ends when the chipselect goes intactive.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: fix bug - spi controller driver does not assert/deassert CS correctly

This bug can be observed when two SPI devices are sharing the spi bus: One
device is set as SPI CS 7, another one is using SPI CS 4.

In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG
register.  From the debug bellow:

cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7
cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4

When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however,
SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode).

Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7
is asserted, however SPISSEL4 will be asserted too (I can see this using
the scope).  This is unreasonable according to HRM.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: tweak magic spi dma sequence to get it working on BF54x

Without this change, SPI DMA is not reliably under stress tests.
Obiviously it's a hardware issue which is not addressed by any document.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: add timeout while waiting for SPIF in dma irq handler

The "while" endless loop will cause the system hang if hardware error, so
we add timeout control to make the system alive.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: get dma working for SPI flashes

When using a BF533-STAMP here with a W25X10 SPI flash.  It works fine when
enable_dma is disabled, but doesn't work at all when turning DMA on.  We
get just 0xff bytes back when trying to read the device.

Change the code around so that it programs the SPI first and then enables
DMA, it seems to work a lot better ...

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: SPI slave select code cleanup

- remove duplicated definition MAX_SPI_SSEL

- remove unnecessary array size

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: use the properl BIT_CTL_xxx defines

use the properl BIT_CTL_...  defines rather than the internal driv er
CFG_SPI_...  defines

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: do not check for SPI errors if DMA itself did not flag any

We only need to check SPI error when DMA failes, cause that is the DMA IRQ
handling routine.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: add a few more DMA debug messages

Because of DMA hardware issue, we were trying to use software workaround.
This patch add some useful debug messages to help us debugging the DMA
code.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: drop bogus cast and touchup dma label

Blackfin's related DMA callback API doesn't need void * cast, so drop it.
And this driver is for all Blackfin processors not only for BF53x, we
update the DMA request label for more meaningful information.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: unify duplicated code in dma read/write paths

For DMA TX/RX operation in pump_transfers, DMA contriguration code in TX
and RX paths are almost the same.  This patch unify the duplicated DMA
code to make it more readable.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: pass DMA overflow error to the higher level

If the SPI bus registers a receive overflow error, pass the result back up
to the higher levels.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: use len_in_bytes when we care about the number of bytes transferred

Use len_in_bytes when we care about the number of bytes transferred rather
than the number of spi transactions.  (this value will be the same for
8bit transfers, but not any other sizes)

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: remove useless <asm/cplbinit.h>

We already moved bfin_addr_dcachable() and friends into the cacheflush
header where it belongs, so don't need to include <asm/cplbinit.h> here.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: Fix erroneous SPI Clock divisor calculation

Fix erroneous SPI Clock divisor calculation.  Make sure SPI_BAUD is always
>= 2.  Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin SPI Driver: ensure cache coherency before doing DMA

Flush or invalidate caches before doing DMA transfer, if needed.

[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hwmon: add support for GMT G760A fan speed PWM controller

This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.

Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

/proc/pid/maps: don't show pgoff of pure ANON VMAs

Recently, it's argued that what proc/pid/maps shows is ugly when a 32bit
binary runs on 64bit host.

/proc/pid/maps outputs vma's pgoff member but vma->pgoff is of no use
information is the vma is for ANON.  With this patch, /proc/pid/maps shows
just 0 if no file backing store.

[akpm@linux-foundation.org: coding-style fixes]
[kamezawa.hiroyu@jp.fujitsu.com: coding-style fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mike Waychison <mikew@google.com>
Reported-by: Ying Han <yinghan@google.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: add /proc controls for pdflush threads

Add /proc entries to give the admin the ability to control the minimum and
maximum number of pdflush threads.  This allows finer control of pdflush
on both large and small machines.

The rationale is simply one size does not fit all.  Admins on large and/or
small systems may want to tune the min/max pdflush thread count to best
suit their needs.  Right now the min/max is hardcoded to 2/8.  While
probably a fair estimate for smaller machines, large machines with large
numbers of CPUs and large numbers of filesystems/block devices may benefit
from larger numbers of threads working on different block devices.

Even if the background flushing algorithm is radically changed, it is
still likely that multiple threads will be involved and admins would still
desire finer control on the min/max other than to have to recompile the
kernel.

The patch adds '/proc/sys/vm/nr_pdflush_threads_min' and
'/proc/sys/vm/nr_pdflush_threads_max' with r/w permissions.

The minimum value for nr_pdflush_threads_min is 1 and the maximum value is
the current value of nr_pdflush_threads_max.  This minimum is required
since additional thread creation is performed in a pdflush thread itself.

The minimum value for nr_pdflush_threads_max is the current value of
nr_pdflush_threads_min and the maximum value can be 1000.

Documentation/sysctl/vm.txt is also updated.

[akpm@linux-foundation.org: fix comment, fix whitespace, use __read_mostly]
Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix pdflush thread creation upper bound

Fix a race on creating pdflush threads.  Without the patch, it is possible
to create more than MAX_PDFLUSH_THREADS threads, and this has been
observed in practice on IO loaded SMP machines.

The fix involves moving the lock around to protect the check against the
thread count and correctly dealing with thread creation failure.

This fix also _mostly_ repairs a race condition on how quickly the threads
are created.  The original intent was to create a pdflush thread (up to
the max allowed) every second.  Without this patch is is possible to
create NCPUS pdflush threads concurrently.  The 'mostly' caveat is because
an assumption is made that thread creation will be successful.  If we fail
to create the thread, the miss is not considered fatal.  (we will try
again in 1 second)

Signed-off-by: Peter W Morreale <pmorreale@novell.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

esp: fix section mismatch warning

Not critical.

  WARNING: drivers/char/esp.o(.text+0x278): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_version
  The function show_serial_version() references
  the variable __initdata serial_version.
  This is often because show_serial_version lacks a __initdata
  annotation or the annotation of serial_version is wrong.

  WARNING: drivers/char/esp.o(.text+0x27d): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_name
  The function show_serial_version() references
  the variable __initdata serial_name.
  This is often because show_serial_version lacks a __initdata
  annotation or the annotation of serial_name is wrong.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew J. Robinson <arobinso@nyx.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

PCI: Fix oops in pci_vpd_truncate

pci_vpd_truncate() should check for dev->vpd->attr, otherwise this might
happen:

  sky2 driver version 1.22
  Unable to handle kernel paging request for data at address 0x0000000c
  Faulting instruction address: 0xc01836fc
  Oops: Kernel access of bad area, sig: 11 [#1]
  [...]
  NIP [c01836fc] pci_vpd_truncate+0x38/0x40
  LR [c029be18] sky2_probe+0x14c/0x518
  Call Trace:
  [ef82bde0] [c029bda4] sky2_probe+0xd8/0x518 (unreliable)
  [ef82be20] [c018a11c] local_pci_probe+0x24/0x34
  [ef82be30] [c018a14c] pci_call_probe+0x20/0x30
  [ef82be50] [c018a330] __pci_device_probe+0x64/0x78
  [ef82be60] [c018a44c] pci_device_probe+0x30/0x58
  [ef82be80] [c01aa270] really_probe+0x78/0x1a0
  [ef82bea0] [c01aa460] __driver_attach+0xa4/0xa8
  [ef82bec0] [c01a96ac] bus_for_each_dev+0x60/0x9c
  [ef82bef0] [c01aa0b4] driver_attach+0x24/0x34
  [ef82bf00] [c01a9e08] bus_add_driver+0x12c/0x1cc
  [ef82bf20] [c01aa87c] driver_register+0x6c/0x110
  [ef82bf30] [c018a770] __pci_register_driver+0x4c/0x9c
  [ef82bf50] [c03782c8] sky2_init_module+0x30/0x40
  [ef82bf60] [c0001dbc] do_one_initcall+0x34/0x1a0
  [ef82bfd0] [c0362240] do_initcalls+0x38/0x58

This happens with CONFIG_SKY2=y, and "ip=on" kernel command line, so
pci_vpd_truncate() is called before late_initcall(pci_sysfs_init),
therefore ->attr isn't yet initialized.

Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  tomoyo: remove "undelete domain" command.

Merge git://git./linux/kernel/git/rusty/linux-2.6-module-and-param

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
  Revert "module: remove the SHF_ALLOC flag on the __versions section."

Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
  powerpc: Fix oops when loading modules
  powerpc: Wire up preadv and pwritev
  powerpc/ftrace: Fix printf format warning
  powerpc/ftrace: Fix #if that should be #ifdef
  powerpc: Fix ptrace compat wrapper for FPU register access
  powerpc: Print information about mapping hw irqs to virtual irqs
  powerpc: Correct dependency of KEXEC
  powerpc: Disable VSX or current process in giveup_fpu/altivec
  powerpc/pseries: Enable relay in pseries_defconfig
  powerpc/pseries: Fix ibm,client-architecture comment
  powerpc/pseries: Scan for all events in rtasd
  powerpc/pseries: Add dispatch dispersion statistics
  powerpc: Clean up some prom printouts
  powerpc: Print progress of ibm,client-architecture method
  powerpc: Remove duplicated #include's
  powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
  powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
  fsl-diu-fb: Pass the proper device for dma mapping routines
  powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
  cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
  ...

ramfs: fix double freeing s_fs_info on failed mount

If ramfs mount fails, s_fs_info will be freed twice in ramfs_fill_super()
and ramfs_kill_sb(), leading to kernel oops.

Consolidate and beautify the code.
Make sure s_fs_info and s_root are in known good states.

Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Revert "module: remove the SHF_ALLOC flag on the __versions section."

This reverts commit 9cb610d8e35fe3ec95a2fe2030b02f85aeea83c1.

This was an impressively stupid patch.  Firstly, we reset the SHF_ALLOC
flag lower down in the same function, so the patch was useless.  Even
better, find_sec() ignores sections with SHF_ALLOC not set, so
it breaks CONFIG_MODVERSIONS=y with CONFIG_MODULE_FORCE_LOAD=n, which
refuses to load the module since it can't find the __versions section.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

tomoyo: remove "undelete domain" command.

Since TOMOYO's policy management tools does not use the "undelete domain"
command, we decided to remove that command.

Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>

powerpc: Fix oops when loading modules

This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops.  We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.

This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.

Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Wire up preadv and pwritev

[paulus@samba.org: changed to use syscall numbers 320 and 321 since
 perf_counters is currently using 319.]

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/ftrace: Fix printf format warning

'tramp' is an unsigned long, so print it with %lx.

Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/ftrace: Fix #if that should be #ifdef

Commit bb7253403f7a4670a128e4c080fd8ea1bd4d5029 ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64.  This changes it to #ifdef.

Fixes the following warning on 32-bit builds:
 arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Fix ptrace compat wrapper for FPU register access

The ptrace compat wrapper mishandles access to the fpu registers.  The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro.  The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset).  The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Print information about mapping hw irqs to virtual irqs

The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.

So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Correct dependency of KEXEC

commit 28794d34ecb6815a3fa0a4256027c9b081a17c5f ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Disable VSX or current process in giveup_fpu/altivec

When we call giveup_fpu, we need to need to turn off VSX for the
current process.  If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct.  Ditto for
altivec.

This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on.  Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.

   lfs unaligned   <- alignment exception turns FP off but leaves VSX on

   VSX instruction <- no exception since VSX on, hence we get the
                      wrong VSX register values for VSX registers 0-31,
                      which overlap the FPRs.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/pseries: Enable relay in pseries_defconfig

Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/pseries: Fix ibm,client-architecture comment

We specify a 64MB RMO, but the comment says 128MB.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/pseries: Scan for all events in rtasd

Instead of checking for known events, pass in all 1s so we handle future
event types.  We were currently missing the IO event type.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/pseries: Add dispatch dispersion statistics

PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Clean up some prom printouts

Make all messages consistent, some have spaces before the "...", some do not.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Print progress of ibm,client-architecture method

The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:

Hypertas detected, assuming LPAR !

Which doesn't explain what just happened.  Wrap the ibm,client-architecture
so it's clear what is going on:

Calling ibm,client-architecture... done

In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Remove duplicated #include's

Remove duplicated #include's in
  - arch/powerpc/include/asm/ps3fb.h
  - arch/powerpc/kernel/setup-common.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook

The (relatively) new pmac_zilog driver doesn't use the pre-munged
IRQ numbers from the macio_dev unlike other macio things, it
directly maps it off the OF device-tree.

It does that because it can be initialized much earlier than the
registration of the macio devices, in order to get a serial
console early.

Unfortunately, that means that it "misses" some fixups done
by the macio layer to work around missing interrupt descriptions
in the device-tree of the Wallstreet machines.

This patch brings the necessary workaround into the pmac_zilog
driver itself to bring it back to working condition.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf

The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA.  To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value.  We can't
just make it static because this can be compiled in as a module.

Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.

Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Merge branch 'next' of /linux/kernel/git/galak/powerpc into merge

Merge branch 'for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (120 commits)
  cx231xx: Convert to snd_card_create()
  V4L/DVB (11440): PWC: fix build error when CONFIG_INPUT=m
  V4L/DVB (11439): UVC: uvc_status_cleanup(): undefined reference to `input_unregister_device'
  V4L/DVB (11438): au0828: fix Kconfig dependance
  V4L/DVB (11437): pvrusb2: Drop client_register/unregister stubs
  V4L/DVB (11436): radio-mr800: convert to to v4l2_device
  V4L/DVB (11435): dsbr100 radio: convert to to v4l2_device
  V4L/DVB: zr364xx: remove unused #include <version.h>
  V4L/DVB: usbvision: remove unused #include <version.h>
  V4L/DVB (11427): gspca - m5602: Minor cleanups
  V4L/DVB (11426): gspca - m5602: Don't touch hflip/vflip register on Read/Modify/Write
  V4L/DVB (11425): gspca - m5602: Move the vflip quirk to probe stage.
  V4L/DVB (11424): gspca - m5602-ov9650: Use the local ctrl cache. Adjust image on vflip.
  V4L/DVB (11423): gspca - m5602-ov9650: Add a disconnect hook, setup a ctrl cache ctrl.
  V4L/DVB (11422): gspca - m5602-ov9650: Replace a magic constant with a define
  V4L/DVB (11421): gspca - m5602-ov9650: Synthesize modesetting.
  V4L/DVB (11420): gspca - m5602: Improve error handling in the ov9650 driver
  V4L/DVB (11419): gspca - m5602-ov9650: Don't read exposure data from COM1.
  V4L/DVB (11418): gspca - m5602-ov9650: Auto white balancing is on by default
  V4L/DVB (11417): gspca - m5602-ov9650: Autogain is on by default
  ...

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  b44: Use kernel DMA addresses for the kernel DMA API
  forcedeth: Fix resume from hibernation regression.
  xfrm: fix fragmentation on inter family tunnels
  ibm_newemac: Fix dangerous struct assumption
  gigaset: documentation update
  gigaset: in file ops, check for device disconnect before anything else
  bas_gigaset: use tasklet_hi_schedule for timing critical tasklets
  net/802/fddi.c: add MODULE_LICENSE
  smsc911x: remove unused #include <linux/version.h>
  axnet_cs: fix phy_id detection for bogus Asix chip.
  bnx2: Use request_firmware()
  b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
  socket: use percpu_add() while updating sockets_in_use
  virtio_net: Set the mac config only when VIRITO_NET_F_MAC
  myri_sbus: use request_firmware
  e1000: fix loss of multicast packets
  vxge: should include tcp.h

Conflict in firmware/WHENCE (SCSI vs net firmware)

b44: Use kernel DMA addresses for the kernel DMA API

We must not use the device DMA addresses for the kernel DMA API, because
device DMA addresses have an additional offset added for the SSB translation.

Use the original dma_addr_t for the sync operation.

Cc: stable@kernel.org
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: Fix resume from hibernation regression.

Reset phy state on resume, fixing a regression caused by powering down
the phy on hibernate.

Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cx231xx: Convert to snd_card_create()

Convert from snd_card_new() to the new snd_card_create() function.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11440): PWC: fix build error when CONFIG_INPUT=m

Fix build errors when USB_PWC=y and INPUT=m.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11439): UVC: uvc_status_cleanup(): undefined reference to `input_unregister_device'

Fix build errors when USB_VIDEO_CLASS=y and INPUT=m.
Fixes kernel bugzilla #12671.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11438): au0828: fix Kconfig dependance

Fix this build error:
ERROR: "videobuf_queue_vmalloc_init" [drivers/media/video/au0828/au0828.ko] undefined!
ERROR: "videobuf_vmalloc_free" [drivers/media/video/au0828/au0828.ko] undefined!
ERROR: "videobuf_to_vmalloc" [drivers/media/video/au0828/au0828.ko] undefined!

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11437): pvrusb2: Drop client_register/unregister stubs

The client_register and client_unregister methods are optional so
there is no point in defining stub ones. Especially when these methods
are likely to be removed soon.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11436): radio-mr800: convert to to v4l2_device

radio-mr800: convert to to v4l2_device.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11435): dsbr100 radio: convert to to v4l2_device

dsbr100: convert to v4l2_device.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: zr364xx: remove unused #include <version.h>

Remove unused #include <version.h> in drivers/media/video/zr364xx.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: usbvision: remove unused #include <version.h>

Remove unused #include <version.h> in
drivers/media/video/usbvision/usbvision-i2c.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11427): gspca - m5602: Minor cleanups

Remove an unnecessary error check and reorder some code.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11426): gspca - m5602: Don't touch hflip/vflip register on Read/Modify/Write

Touching the hflip/vflip register while doing the read/modify/write corrupts the image. Just read from the sensor ctrl cache instead and all is good.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11425): gspca - m5602: Move the vflip quirk to probe stage.

The vflip quirk is better checked at probe time as it's only needed once.
Also add an extra reset at init time to resolve a suspend to ram regression.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11424): gspca - m5602-ov9650: Use the local ctrl cache. Adjust image on vflip.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11423): gspca - m5602-ov9650: Add a disconnect hook, setup a ctrl cache ctrl.

Reading and writing to a register doesn't always work reliably. Add a cache
and ensure that it is deallocated properly upon module disconnect.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11422): gspca - m5602-ov9650: Replace a magic constant with a define

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11421): gspca - m5602-ov9650: Synthesize modesetting.

Previously all resolution setting was done with precalculated tables.
When the image is vflipped we need to adjust the alignment which would
require another table. Now we can adjust the parameters on the fly instead.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11420): gspca - m5602: Improve error handling in the ov9650 driver

Some errors were not propagated properly.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11419): gspca - m5602-ov9650: Don't read exposure data from COM1.

ov9650: Reading the COM1 register corrupts the image.
Decrease the granularity of the exposure and limit its upper range
as setting such high values doesn't have any effect on the image.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11418): gspca - m5602-ov9650: Auto white balancing is on by default

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11417): gspca - m5602-ov9650: Autogain is on by default

Autogain is on by default, properly set the default value in the v4l2 ctrl.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11416): gspca - m5602: Constify all sensor structs

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11415): gspca - m5602: Remove an unused member in the sd struct.

Remove an unused sd struct member. Remove a redundant define while we're at it.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11414): gspca - m5602-mt9m111: Move v4l2 controls to main sensor file.

Move over the v4l2 controls to the sensor specific source file.
Remove the now redundant sensor struct member.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11413): gspca - m5602-mt9m111: Separate mode vectors per sensor.

By separating the supported for each sensor into a separate vector we can
eliminate the nmodes variable and instead calculate it at runtime.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11412): gspca - m5602-ov9650: Checkpatch fixes

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11411): gspca - m5602: Rework v4l ctrl handling in all sensors

Previously, all sensors allocated a part of a large ctrl vector.
Define this vector separately for each sensor instead.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11410): gspca - m5602-ov9650: Always init the ov9650 before starting a stream

This is a hack preventing a suspend-to-ram/disk regression.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11409): gspca - m5602-ov9650: Set the ov9650 sensor in soft sleep when inactive.

In order to save energy, put the sensor in soft sleep mode when not active

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11408): gspca - m5602-s5k83a: Add led support to the s5k83a sensor.

This patch toggles the led seen on many laptops having a m5602 connected
to a Samsung s5k83a sensor.

Signed-off-by: Lukas Karas <lukas.karas@centrum.cz>
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11407): gspca - m5602-ov9650: Clean up ov9650_start() function.

Cleans some unnecessary temporary variable usage in the ov9650 start function.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11406): gspca - m5602-ov9650: Add QCIF resolution support

Adds QCIF support for the ov9650 sensor

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (11405): gspca - m5602: Simplify error handling

Simplfy error handling by replacing goto statements with return equivalents.

Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>