[PPC] Remove 83xx from arch/ppc

83xx exists in arch/powerpc as well as cuImage support to boot from
a u-boot that doesn't support device trees.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: add the mpc837x rdb defconfig

Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: add the mpc837[789]_rdb dts files

Add the dts files for the MPC838xE Reference Development Board (RDB).

The board is a mini-ITX reference board with 256M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.

the difference among the three files is the 8377 has two, the 8378
none, and the 8379 has four sata controllers.

partially based on the 8379 mds device trees.

Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: add MPC837x RDB platform support

primarily based on mpc837x mds code.

Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: add the mpc8315 rdb defconfig

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: ipic: add interrupt vector 94

This is used on the mpc8315 SoC for TDM DMA error interrupts.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: enable FSL SATA driver config for Freescale SoCs

The mpc8315 shares the same SATA controller as the mpc837x,
and likelihood is that future SoCs from Freescale will also.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: Add the MPC8315E RDB dts

Add the dts for the MPC8315E Reference Development Board (RDB).

The board is a mini-ITX reference board with 128M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: add base platform support for the mpc8315 rdb board

mpc8315 identical to mpc8313 here, just check compatible.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: fold the mpc8313 platform into the mpc831x platform

prepare for adding support for the mpc8315 rdb, since they are
identical wrt platform code.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] fsl_spi: stop using device_type = "spi"

Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
  it for legacy device_type probing and new "compatible" probing.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

spi_mpc83xx: use brg-frequency for SPI in QE

In case of QE we can use brg-frequency (which is qeclk/2).
Thus no need to divide sysclk in the spi_mpc83xx.

This patch also adds code to use get_brgfreq() on QE chips.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

ucc_geth: get rid of device_type for mdio

device_type property is bogus, thus use proper compatible.

Also change compatible property to "fsl,ucc-mdio".

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] QE: get rid of most device_types and model

Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".

Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: some minor cleanups for stx_gp3 and tqm85xx

* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: mpc834x_mds - Convert device tree source to dts-v1

Move mpc834x_mds device tree source forward to dts-v1 format.  Nothing
too complex in this one, so it boils down to just adding a bunch of 0x
in the right places and converting clock speeds to decimal.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] CPM: Move definition of buffer descriptor to cpm.h

Buffer descriptors are used by both CPM1 and CPM2. Move the definitions
from the cpm dependent include file to common cpm.h

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] CPM: Rename commproc to cpm1 and cpm2_common.c to cpm2.c

Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Get rid of conditional includes of board specific setup

Directly include mpc885ads.h from mpc885ads_setup.c. Now we can get rid
of the arch dependent includes in mpc8xx.h.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Remove sysdev/commproc.h

Move cpm1 specific prototypes to asm/commproc.h and mpc8xx specific
prototypes to asm/mpc8xx.h. Adjust includes accordingly. Remove now
unneeded sysdev/commproc.h.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Remove unneeded and misspelled prototype m8xx_calibrate_decr

m8xx_calibrate_decr seems to be a misspelled prototype for
mpc8xx_calibrate_decr. As it's not needed anyways, just remove it.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Rename m8xx_pic_init to mpc8xx_pics_init

m8xx_pic_init calls both mpc8xx_pic_init and cpm_pic_init. Renaming the
function to use the same name space as the rest of the mpc8xx
specific funtions and to be more meaningful.

m8xx_pic_init is declared in ppc8xx_pic.h but defined nowhere in the ppc
tree. Remove it.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Remove unused m8xx_cpm_hostalloc/free/dump()

m8xx_cpm_hostalloc is still defined in commproc.c, but no users are left
in the kernel tree. m8xx_cpm_hostfree and m8xx_cpm_hostdump are only
defined in the headers. Remove this dead code.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: Add default config file for Wind River SBC8349 board

Default config file for SBC8349 board, suitable for use as with NFS as
a root file system and gianfar as the NFS root device.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: Add device tree source for Wind River SBC834x board.

This adds the device tree source for the Wind River SBC834x board.
It is based on the MPC834x_MDS DTS, with the biggest difference being
the lack of BCSR and the PCI2 that the MDS gets via the PIB. That,
and this file is also dts-v1 format.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 83xx: Add support for Wind River SBC834x boards

This adds the basic support for the Wind River SBC834x boards.  The
SBC8349 is more common, although it should work on the SBC8347 board
as well.  Support is heavily based on the existing MPC834x_MDS code.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Add default .config file for Wind River SBC8548

This is a suitable .config file for building the WRS SBC8548 kernel
to be used for NFS root via one of the TSEC interfaces and with
serial console via the soc/16550 compatible UART.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Add v1 device tree source for Wind River SBC8548 board

This adds a v1 device tree source for the Wind River SBC8548 board.
The biggest difference between this and the MPC8548CDS reference
platform is the absence of the CDS's Arcadia peripherals and physical
access to the PCI#2 bus.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Add basic support for Wind River SBC8548 board

This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc.  It closely follows the implementation of the MPC8548CDS.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Add default .config file for Wind River SBC8560

This is a suitable .config file for building the WRS SBC8560 kernel
to be used for NFS root via one of the TSEC interfaces and with
serial console via the 16550 compatible UART on the board.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] CPM2: Make support for the CPM2 optional on 8560 based boards

Currently there is no way to disable the CPM2 support.  Some boards,
like the SBC8560 have their own external UART and don't have any direct
dependencies on the CPM for a serial console or anything else.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Add v1 device tree source for Wind River SBC8560 board

This adds a v1 device tree source for the Wind River SBC8560 board.  The
biggest difference between this and the MPC8560ADS reference platform
dts is the use of an external 16550 compatible UART instead of the CPM2.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Add support for Wind River SBC8560 in arch/powerpc

This adds support for the Wind River SBC8560 board, implemented as
powerpc.  It closely follows the implementation of the MPC8560ADS.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Reduce code duplication in legacy_serial, add UART parent types

The legacy_serial was treating each UART parent in a separate code block.
Rather than continue this trend for the new parent IDs, this condenses
all (soc, tsi, opb, plus two more new types) into one of_device_id array.
The new types are wrs,epld-localbus for the Wind River sbc8560, and a
more generic "simple-bus" as requested by Scott Wood.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 82xx and embedded6xx: Use machine_*_initcall() hooks in platform code

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add docs for Freescale PowerQUICC SATA device tree nodes

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add docs for Freescale DMA & DMA channel device tree nodes

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Port TQM85xx boards over from arch/ppc

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 85xx: Port STX GP3 board over from arch/ppc

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add a cuboot wrapper for 85xx with CPM2

The bd info struct changes if we have CPM2 enabled in u-boot.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] bootwrapper: Add find_node_by_compatible

Add the ability to find a device node by just what its compatible with.
This is useful in cases that we don't have a prop to find the node with.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Always build setup-bus.c on powerpc

The common arch/powerpc code calls in to functions in setup-bus.c
so some builds of ppc32 would fail.

Note, ppc32 usage of setup-irq.c is limited to arch/ppc and should be
removed when arch/ppc goes away.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Revert "[POWERPC] Fake NUMA emulation for PowerPC"

This reverts commit 5c3f5892a2db6757a72ce8b27cba90db06683e1d,
basically because it changes behaviour even when no fake NUMA
information is specified on the kernel command line.

Firstly, it changes the nid, thus destroying the real NUMA
information.  Secondly, it also changes behaviour in that if a node
ends up with no memory in it because of the memory limit, we used to
set it online and now we don't.

Also, in the non-NUMA case with no fake NUMA information, we do
node_set_online once for each LMB now, whereas previously we only did
it once.  I don't know if that is actually a problem, but it does seem
unnecessary.

Signed-off-by: Paul Mackerras <paulus@samba.org>

Merge branch 'for-2.6.25' of /linux/kernel/git/jwboyer/powerpc-4xx

[POWERPC] 4xx: logical/bitand typo in powerpc/boot/4xx.c

logical/bitand typo

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: PIKA Warp defconfig

Add the defconfig for the PIKA Warp board

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: PIKA Warp bootwrapper

Add the cuboot wrapper for the PIKA Warp board

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: PIKA Warp DTS

Add the device tree for the PIKA Warp board

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: PIKA Warp base platform

Add the base platform support for the PIKA Warp boards.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: Add PowerPC 440EP Rev C

This adds the 440EP revision C PVR to the CPU table.  The chip has an
FPU on it, so we also match the logical PVR

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Enable RTC for Ebony and Walnut (v2)

This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards.  The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.

Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.

This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented.  That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: Add AMCC Haleakala (405EXr) dts

The patch adds the Haleakala dts. The Haleakala is a stripped down
version of the Kilauea (405EX) with only one EMAC and only one PCIe
interface.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] 4xx: Add 405EXr to cputable

This patch adds the 405EXr to the powerpc cuptable. Basically the 405EXr
is a 405EX with only one EMAC and only one PCIe interface.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

[POWERPC] Autodetect serial console on pegasos2

Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Revert chrp_pci_fixup_vt8231_ata devinit to fix libata on pegasos

Commit 6d98bda79bea0e1be26c0767d0e9923ad3b72f2e changed the init order
for chrp_pci_fixup_vt8231_ata().

It can not work anymore because either the irq is not yet set to 14 or
pci_get_device() returns nothing.  At least the printk() in
chrp_pci_fixup_vt8231_ata() does not trigger anymore.
pata_via works again on Pegasos with the change below.

Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Make IOMMU code safe for > 132 GB of memory

Currently the IOMMU code allocates one page for the segment table, that
isn't safe if we have more than 132 GB of RAM.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Remove bogus comment in dma_direct_alloc_coherent()

Since commit c80d9133e99de1af607314107910a2a1645efb17 (Make direct DMA use
node local allocations) went in this comment makes no sense.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Remove the global dma_direct_offset

We no longer need the global dma_direct_offset, update the comment to
reflect the new reality.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Have celleb use its own dma_direct_offset variable

Rather than using the global variable, have celleb use its own
variable to store the direct DMA offset.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Have cell use its own dma_direct_offset variable

Rather than using the global variable, have cell use its own variable
to store the direct DMA offset.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Use archdata.dma_data in dma_direct_ops and add the offset

Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, we can change the dma_direct_ops to
retrieve the offset from the dma_data, rather than directly from the
global.

While we're here, change the way the offset is used - instead of
or'ing it into the value, add it.  This should have no effect on
current implementations where the offset is far larger than memory,
however in future we may want to use smaller offsets.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Add celleb_dma_dev_setup()

Celleb always uses dma_direct_ops, and sets dma_direct_offset, so it
too should set dma_data to dma_direct_offset.

Currently there's no pci_dma_dev_setup() routine for Celleb so add one.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Set archdata.dma_data for direct DMA in cell_dma_dev_setup()

Store the direct_dma_offset in each device's dma_data in the case
where we're using the direct DMA ops.

We need to make sure we setup the ppc_md.pci_dma_dev_setup() callback
if we're using a non-zero offset.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Always hookup PHB IO resource even when empty

We must always hookup the pci_bus resource 0 to the PHB io_resource
even if the latter is empty (the bus has no IO support).  Otherwise,
some other code will end up hooking it up to something bogus and the
resource tree will end up being broken.

This fixes boot on QS20 Cell blades where the IDE driver failed to
allocate the IO resources due to breakage of the resource tree.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Update ps3_defconfig

Update ps3_defconfig.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Remove lpar address workaround

Remove the PS3 workaround needed to support sparsemem SPU mappings.
The SPU mappings no longer use sparsemem, so this workaround is no
longer needed.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Vuart: change semaphore to mutex

A general housekeeping change of the PS3 vuart variable
vuart_bus_priv.probe_mutex from semaphore to mutex.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Add logical performance monitor driver support

Add PS3 logical performance monitor (lpm) device driver.

The PS3's LV1 hypervisor provides a Logical Performance Monitor that
abstracts the Cell processor's performance monitor features for use
by guest operating systems.

Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Add logical performance monitor device support

Add PS3 logical performance monitor device support to the
PS3 system-bus and platform device registration routines.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Add logical performance monitor repository routines

Add repository routines for the PS3 Logical Performance Monitor.

Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Checkpatch cleanups for arch/powerpc/platforms/ps3/repository.c

Cleanup coding errors in arch/powerpc/platforms/ps3/repository.c as
reported by sparse and checkpatch.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Checkpatch cleanups for drivers/ps3/ps3-vuart.c

Cleanup coding errors in drivers/ps3/ps3-vuart.c as reported by
checkpatch.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Checkpatch cleanups for drivers/ps3/ps3-sys-manager.c

Cleanup coding errors in drivers/ps3/ps3-sys-manager.c as reported
by checkpatch.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Refactor ps3_repository_find_device()

PS3: Refactor ps3_repository_find_device() to use the existing
ps3_repository_read_bus_id() routine.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Kill unused ps3_repository_bump_device()

PS3: Kill unused routine ps3_repository_bump_device().

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Add repository polling loop to work around timing bug

PS3: Add repository polling loop to work around timing bug

On some firmware versions (e.g. 1.90), the storage device may not show up
in the repository immediately after receiving the notification message.
Add a small polling loop to make sure we don't miss it.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Use the HVs storage device notification mechanism properly

The PS3 hypervisor has a storage device notification mechanism to wait
until a storage device is ready.  Unfortunately the storage device
probing code used this mechanism in an incorrect way, needing a
polling loop and handling of devices that are not yet ready.

This change corrects this by:
  - First waiting for the reception of an asynchronous notification
    that a new storage device became ready,
  - Then looking up the storage device in the device repository.

On shutdown, the storage probe thread is stopped and the storage
notification device is closed using a reboot notifier.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Add ps3_repository_find_device_by_id()

The storage probe feature of the PS3 hypervisor returns device IDs.  Add
the corresponding repository routine ps3_repository_find_device_by_id()
which can be used to retrieve the device info from the repository.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] PS3: Make bus_id and dev_id u64

Change the PS3 bus_id and dev_id from type unsigned int to u64.  These
IDs are 64-bit in the repository, and the special storage notification
device has a device ID of ULONG_MAX.

Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Add definition of Cell bookmark SPR

Add a definition for the Cell bookmark SPR to asm-powerpc/regs.h.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] kdump shutdown hook support

This adds hooks into the default_machine_crash_shutdown so drivers can
register a function to be run in the first kernel before we hand off
to the second kernel.  This should only be used in exceptional
circumstances, like where the device can't be reset in the second
kernel alone (as is the case with eHEA).  To emphasize this, the
number of handles allowed to be registered is currently #def to 1.

This uses the setjmp/longjmp code around the call out to the
registered hooks, so any bogus exceptions we encounter will hopefully
be recoverable.

Tested with bogus data and instruction exceptions.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Make setjmp/longjmp code usable outside of xmon

This makes the setjmp/longjmp code used by xmon, generically available
to other code.  It also removes the requirement for debugger hooks to
be only called on 0x300 (data storage) exception.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Fix a couple of copyright symbols

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Make ibmebus use of_(un)register_driver

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Export copy_page() on 32bit

Export copy_page() on 32-bit powerpc; unionfs needs it.

Unionfs already builds as a module on 64bit powerpc, so the export is
placed within an existing CONFIG_PPC32 #ifdef.

Signed-off-by: Joseph Fannin <jfannin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Make smp_send_stop() handle panic and xmon reboot

smp_send_stop() will send an IPI to all other cpus to shut them down.
However, for the case of xmon-based reboots (as well as potentially some
panics), the other cpus are (or might be) spinning with interrupts off,
and won't take the IPI.

Current code will drop us into the debugger when the IPI fails, which
means we're in an infinite loop that we can't get out of without an
external reset of some sort.

Instead, make the smp_send_stop() IPI call path just print the warning
about being unable to send IPIs, but make it return so the rest of the
shutdown sequence can continue. It's not perfect, but the lesser of
two evils.

Also move the call_lock handling outside of smp_call_function_map so we
can avoid deadlocks in smp_send_stop().

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Make smp_call_function_map static

smp_call_function_map should be static, and for consistency prepend it
with __ like other local helper functions in the same file.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Merge branch 'for-2.6.25' of /linux/kernel/git/galak/powerpc into for-2.6.25

[POWERPC] Add initial storcenter config file.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add initial iomega StorCenter board port.

Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add StorCenter DTS first draft.

Based on the Kurobox DTS files.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Add _nmask_and_or_msr() declartion to asm-powerpc/system.h

Prevents miscellaneous users from declaring it locally.

Signed-off-by: Jon Loeliger <jdl@freecale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

fs_enet: Add fixed-phy support for fs_enet

This patch adds support to use the fixed-link property of an ethernet node
to fs_enet for the CONFIG_PPC_CPM_NEW_BINDING case.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Vitali Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: Use machine_*_initcall() hooks in platform code

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Fix compile error if CONFIG_STX_GP3 is defined

cpmux is need in all cases, having wrapped by the ifndef CONFIG_STX_GP3
was causing a compile error.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] Move RapidIO support code from arch/ppc

Do just enough to move the RapidIO support code for 85xx over from arch/ppc
into arch/powerpc and make it still build.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[RAPIDIO] Fix compile error and warning

drivers/rapidio/rio.c: In function 'rio_get_asm':
drivers/rapidio/rio.c:413: error: implicit declaration of function 'in_interrupt'
drivers/rapidio/rio.c: In function 'rio_init_mports':
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 86xx: MPC8641 HPCN - call of_platform_bus_probe()

Call of_platform_bus_probe() on the MPC8641 HPCN, similar to what is
done for other platforms.

Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 86xx: Add localbus and flash nodes to mpc8641_hpcn.dts

Add local bus, flash, and MTD partition nodes to mpc8641_hpcn.dts

Also add compatible field for the soc node, so that it will be picked up
by of_platform_bus_probe().

Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

[POWERPC] 8xx: adder875 - Fix flash bus-width and remove duplicate __initdata

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>