firefly-linux-kernel-4.4.55.git
12 years agomwifiex: retrieve correct max_power information in reg_notifier handler
Amitkumar Karwar [Thu, 28 Jun 2012 02:57:59 +0000 (19:57 -0700)]
mwifiex: retrieve correct max_power information in reg_notifier handler

As we don't provide custom regulatory rules to cfg80211,
"chan->max_power" remains uninitialized (0dbm) and
"chan->max_reg_power" will contain maximum power for a channel
extracted from regulatory rules provided by CRDA; hence use
"chan->max_reg_power" in reg_notifier handler instead of
"chan->max_power" to set max_power in firmware.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agomwifiex: do not advertise custom regulatory domain capability
Amitkumar Karwar [Thu, 28 Jun 2012 02:57:58 +0000 (19:57 -0700)]
mwifiex: do not advertise custom regulatory domain capability

Since we don't support custom regulatory domains,
WIPHY_FLAG_CUSTOM_REGULATORY should not be enabled during wiphy
registration.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agomwifiex: use correct firmware command to get power limits
Amitkumar Karwar [Thu, 28 Jun 2012 02:57:57 +0000 (19:57 -0700)]
mwifiex: use correct firmware command to get power limits

"priv->max_tx_power_level" and "priv->min_tx_power_level" variables
are initialized to maximum and minimum power levels supported by
hardware by sending correct firmware command.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agomwifiex: wakeup main thread to handle command queued
Amitkumar Karwar [Thu, 28 Jun 2012 02:57:56 +0000 (19:57 -0700)]
mwifiex: wakeup main thread to handle command queued

We miss to wakeup main thread after adding command to cmd pending
queue at follwing places. These commands are handled later when
main thread is woken up for handling an interrupt for sleep event
from firmware. This adds worst case delay of 50msec.

1) We don't wakeup main thread when asynchronous command is added
to cmd pending queue. Move queue_work() call from
mwifiex_wait_queue_complete() to mwifiex_send_cmd_async() to wakeup
main thread for sync as well as async commands.

2) Scan operation is triggered due to following reasons
   a) request from user (ex. "iw scan" command)
   b) Scan performed by driver internally.
   In first case main thread is woken up when first scan command is
queued in cmd pending queue (we don't need to wakeup main thread for
subsequent scan commands, because they are queued in scan command
response handler), but it is not done for second case. queue_work()
is moved inside mwifiex_scan_networks() to handle both the cases.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: de-duplicate initvals
Felix Fietkau [Thu, 28 Jun 2012 00:33:41 +0000 (02:33 +0200)]
ath9k: de-duplicate initvals

The initvals tool from https://github.com/mcgrof/qca-swiss-army-knife has
been modified to detect identical initval tables and replace them with
macros. This patch contains the generated changes.

On MIPS this reduces the binary size by 24 KB with no runtime changes.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: update AR934x initvals to latest version
Felix Fietkau [Thu, 28 Jun 2012 00:33:40 +0000 (02:33 +0200)]
ath9k: update AR934x initvals to latest version

Generated using the initvals tool from the qca-swiss-army-knife repository
from https://github.com/mcgrof/qca-swiss-army-knife

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: Fix signedness in a MCI debug message
Mohammed Shafi Shajakhan [Wed, 27 Jun 2012 14:30:27 +0000 (20:00 +0530)]
ath9k: Fix signedness in a MCI debug message

seems i got a message like this
ath: phy0: BT_Status_Update: is_link=0, linkId=2,
state=1, SEQ=-2085766476 initially.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_hw: make use of the wrapper to check for MCI init
Mohammed Shafi Shajakhan [Wed, 27 Jun 2012 14:30:26 +0000 (20:00 +0530)]
ath9k_hw: make use of the wrapper to check for MCI init

ath9k_hw_mci_is_enabled wrapper also takes care of
ATH9K_HW_CAP_MCI being set for the AR9462 under test.

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: fix ANI operation in AP mode
Felix Fietkau [Wed, 27 Jun 2012 12:58:19 +0000 (14:58 +0200)]
ath9k: fix ANI operation in AP mode

ath9k_ani_reset (which is called at reset time) uses a state variable
ani->update_ani to prevent the ANI noise immunity state on the operating
channel from being overwritten by background scans. Unfortunately this
is also being set for AP mode, since it's mixed with code that is only
supposed to change the default settings after a reset.

In AP mode this has the side effect of having ANI run, but being unable to
change its runtime noise immunity level, making it effectively useless.

Fix this by getting rid of ani->update_ani and passing a parameter to
ath9k_hw_set_ofdm_nil and ath9k_hw_set_cck_nil instead.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoiwlegacy: print how long queue was actually stuck
Paul Bolle [Wed, 27 Jun 2012 08:36:27 +0000 (10:36 +0200)]
iwlegacy: print how long queue was actually stuck

Every now and then, after resuming from suspend, the iwlegacy driver
prints
    iwl4965 0000:03:00.0: Queue 2 stuck for 2000 ms.
    iwl4965 0000:03:00.0: On demand firmware reload

I have no idea what causes these errors. But the code currently uses
wd_timeout in the first error. wd_timeout will generally be set at
IL_DEF_WD_TIMEOUT (ie, 2000). Perhaps printing for how long the queue
was actually stuck can clarify the cause of these errors.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: Fix compilation breakage
Sujith Manoharan [Wed, 27 Jun 2012 08:45:59 +0000 (14:15 +0530)]
ath9k: Fix compilation breakage

Wrap the MCI-work canceling with CONFIG_ATH9K_BTCOEX_SUPPORT.

Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: fix sparse warning introduced with checkdied patch
Arend van Spriel [Tue, 26 Jun 2012 19:26:40 +0000 (21:26 +0200)]
brcmfmac: fix sparse warning introduced with checkdied patch

The commit "brcmfmac: introduce checkdied debugfs functionality"
also introduced a sparse warning:

..../brcmfmac/dhd_sdio.c:3147:45: sparse: cast to restricted __le32

This patch fixes this sparse warning.

Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: add BCM4334 support
Franky Lin [Tue, 26 Jun 2012 19:26:39 +0000 (21:26 +0200)]
brcmfmac: add BCM4334 support

BCM4334 is a dualband a/b/g/n WiFi chip support 20MHz/40MHz
channels. This patch adds support for its SDIO interface.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: reduce allocations needed during nvram data download
Arend van Spriel [Tue, 26 Jun 2012 19:26:38 +0000 (21:26 +0200)]
brcmfmac: reduce allocations needed during nvram data download

The nvram data is preprocessed before being sent to the device
and just before sending an additional allocation was done that
assured word alignment of the data. This has moved to the
preprocessing step to reduce allocations and subsequent copying
of the nvram data.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: use firmware data buffer directly for nvram
Franky Lin [Tue, 26 Jun 2012 19:26:37 +0000 (21:26 +0200)]
brcmfmac: use firmware data buffer directly for nvram

The nvram file could be parsed directly in the data buffer in the
firmware structure passed by request_firmware function. This patch
gets rid of the redundant memcpy.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: move glom alignment setting to SDIO bus layer
Franky Lin [Tue, 26 Jun 2012 19:26:36 +0000 (21:26 +0200)]
brcmfmac: move glom alignment setting to SDIO bus layer

txglomming alignment is a SDIO bus specific feature. It is more
appropriate to place it in SDIO bus layer instead of common layer.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: restrict dongle txglom disable to old SDIO core
Franky Lin [Tue, 26 Jun 2012 19:26:35 +0000 (21:26 +0200)]
brcmfmac: restrict dongle txglom disable to old SDIO core

txglomming is a firmware feature for sdio bus interface. For SDIO
device cores newer than revision 11, the default setting of
firmware should be used instead of disabling it from the host side.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: add support for bus specific data command
Franky Lin [Tue, 26 Jun 2012 19:26:34 +0000 (21:26 +0200)]
brcmfmac: add support for bus specific data command

brcmfmac need to support data command setting for dongle's bus
core. A list must be placed at brcmf_bus structure before calling
brcmf_bus_start in order to be sent by brcmf_c_preinit_dcmds.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobcma: define some additional cores IDs
Rafał Miłecki [Mon, 25 Jun 2012 20:12:20 +0000 (22:12 +0200)]
bcma: define some additional cores IDs

Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoMerge branch 'wl12xx-next' into for-linville
Luciano Coelho [Tue, 26 Jun 2012 19:43:29 +0000 (22:43 +0300)]
Merge branch 'wl12xx-next' into for-linville

12 years agoath9k_htc: Fix IDLE power save
Sujith Manoharan [Mon, 25 Jun 2012 08:24:49 +0000 (13:54 +0530)]
ath9k_htc: Fix IDLE power save

Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_htc: Use atomic operations for op_flags
Sujith Manoharan [Mon, 25 Jun 2012 08:24:41 +0000 (13:54 +0530)]
ath9k_htc: Use atomic operations for op_flags

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_htc: Change default listen interval to 1
Sujith Manoharan [Mon, 25 Jun 2012 08:24:30 +0000 (13:54 +0530)]
ath9k_htc: Change default listen interval to 1

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: Fix lockdep splat
Sujith Manoharan [Mon, 25 Jun 2012 08:24:22 +0000 (13:54 +0530)]
ath9k: Fix lockdep splat

Cancel the MCI work only when MCI is actually enabled.
Fixes this:

[96833.124051] Call Trace:
[96833.124060]  [<ffffffff810afaf8>] __lock_acquire+0x1518/0x1e40
[96833.124065]  [<ffffffff810ad126>] ? mark_held_locks+0x86/0x110
[96833.124069]  [<ffffffff810ad3ad>] ? trace_hardirqs_on+0xd/0x10
[96833.124073]  [<ffffffff814464f0>] ? _raw_spin_unlock_irq+0x30/0x70
[96833.124078]  [<ffffffff81072968>] ? wait_on_cpu_work+0x98/0xc0
[96833.124082]  [<ffffffff810b0a11>] lock_acquire+0xa1/0x150
[96833.124085]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124088]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124092]  [<ffffffff810729e2>] wait_on_work+0x52/0x120
[96833.124095]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124099]  [<ffffffff81063b3f>] ? del_timer+0x7f/0x110
[96833.124102]  [<ffffffff81072c13>] __cancel_work_timer+0x83/0x130
[96833.124106]  [<ffffffff81072cf0>] cancel_work_sync+0x10/0x20
[96833.124113]  [<ffffffffa065b5cd>] __ath_cancel_work+0x4d/0x60 [ath9k]
[96833.124119]  [<ffffffffa065cf28>] ath9k_config+0x458/0x680 [ath9k]
[96833.124125]  [<ffffffffa065dd1e>] ? ath9k_flush+0x6e/0x1d0 [ath9k]
[96833.124129]  [<ffffffff8144394d>] ? __mutex_unlock_slowpath+0x10d/0x190
[96833.124146]  [<ffffffffa056c7b5>] ieee80211_hw_config+0x135/0x2a0 [mac80211]
[96833.124163]  [<ffffffffa057ebbb>] ieee80211_do_open+0x67b/0xc50 [mac80211]
[96833.124178]  [<ffffffffa057f1fd>] ieee80211_open+0x6d/0x80 [mac80211]
[96833.124183]  [<ffffffff8137a44f>] __dev_open+0x9f/0xf0
[96833.124187]  [<ffffffff8137a701>] __dev_change_flags+0xa1/0x180
[96833.124190]  [<ffffffff8137a898>] dev_change_flags+0x28/0x70
[96833.124195]  [<ffffffff813e1179>] devinet_ioctl+0x659/0x780
[96833.124199]  [<ffffffff8137aea0>] ? dev_ioctl+0x210/0x6d0
[96833.124203]  [<ffffffff813e1db5>] inet_ioctl+0x75/0x90
[96833.124208]  [<ffffffff8135e0e0>] sock_do_ioctl+0x30/0x70
[96833.124211]  [<ffffffff8135e3dd>] sock_ioctl+0x7d/0x2c0
[96833.124218]  [<ffffffff81193c39>] do_vfs_ioctl+0x99/0x580
[96833.124222]  [<ffffffff81447415>] ? sysret_check+0x22/0x5d
[96833.124226]  [<ffffffff811941b9>] sys_ioctl+0x99/0xa0
[96833.124230]  [<ffffffff814473e9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: raise aggregation limit to 64k for HT IBSS
Sven Eckelmann [Mon, 25 Jun 2012 05:15:22 +0000 (07:15 +0200)]
ath9k: raise aggregation limit to 64k for HT IBSS

mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.

This patch changes this to update ampdu factor/density settings
when starting a blockack session.

Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agortlwifi: rtl8192se: Fix double inclusion of header pci.h
Larry Finger [Sun, 24 Jun 2012 19:44:36 +0000 (14:44 -0500)]
rtlwifi: rtl8192se: Fix double inclusion of header pci.h

The command "make includecheck" yields the following for the rtlwifi tree:

/home/finger/linux-2.6/drivers/net/wireless/rtlwifi/rtl8192se/sw.c: ../pci.h is included more than once.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agortlwifi: Fix IRQ disabled warning
Larry Finger [Sun, 24 Jun 2012 16:06:29 +0000 (11:06 -0500)]
rtlwifi: Fix IRQ disabled warning

The PCI-based drivers can generate the following warning:

[ 9497.776350] ------------[ cut here ]------------
[ 9497.776366] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7a/0xa0()
[ 9497.776370] Hardware name: 05794NC
[ 9497.776597] Pid: 6413, comm: hostapd Not tainted 3.3.0-4.fc16.x86_64 #1
[ 9497.776601] Call Trace:
[ 9497.776612]  [<ffffffff81057b1f>] warn_slowpath_common+0x7f/0xc0
[ 9497.776633]  [<ffffffffa034a099>] ? rtl_pci_reset_trx_ring+0x199/0x230
[rtlwifi]
[ 9497.776640]  [<ffffffff81057b7a>] warn_slowpath_null+0x1a/0x20
[ 9497.776646]  [<ffffffff8105f06a>] local_bh_enable_ip+0x7a/0xa0
[ 9497.776654]  [<ffffffff815f3ef6>] _raw_spin_unlock_bh+0x16/0x20
[ 9497.776671]  [<ffffffffa03e50de>] destroy_conntrack+0x9e/0x120
[nf_conntrack]
[ 9497.776681]  [<ffffffff81511847>] nf_conntrack_destroy+0x17/0x20
[ 9497.776689]  [<ffffffff814d9c85>] skb_release_head_state+0xe5/0x120
[ 9497.776695]  [<ffffffff814d98b6>] __kfree_skb+0x16/0xa0
[ 9497.776700]  [<ffffffff814d9a35>] kfree_skb+0x45/0xc0
[ 9497.776717]  [<ffffffffa034a099>] rtl_pci_reset_trx_ring+0x199/0x230
[rtlwifi]
[ 9497.776734]  [<ffffffffa034a155>] rtl_pci_start+0x25/0x1d0 [rtlwifi]
[ 9497.776750]  [<ffffffffa03440b5>] rtl_op_start+0x55/0x90 [rtlwifi]
[ 9497.776785]  [<ffffffffa02c4956>] ieee80211_do_open+0x296/0xa10 [mac80211]
[ 9497.776794]  [<ffffffff815f7ddd>] ? notifier_call_chain+0x4d/0x70
[ 9497.776828]  [<ffffffffa02c513d>] ieee80211_open+0x6d/0x80 [mac80211]
[ 9497.776836]  [<ffffffff814e8b3f>] __dev_open+0x8f/0xe0
[ 9497.776842]  [<ffffffff814e8de1>] __dev_change_flags+0xa1/0x180
[ 9497.776847]  [<ffffffff814e8f78>] dev_change_flags+0x28/0x70
[ 9497.776856]  [<ffffffff8154e99d>] devinet_ioctl+0x61d/0x7b0
[ 9497.776863]  [<ffffffff8154ef55>] inet_ioctl+0x75/0x90
[ 9497.776870]  [<ffffffff814cdd50>] sock_do_ioctl+0x30/0x70
[ 9497.776876]  [<ffffffff814cee09>] sock_ioctl+0x79/0x2f0
[ 9497.776885]  [<ffffffff81193498>] do_vfs_ioctl+0x98/0x550
[ 9497.776891]  [<ffffffff811939e1>] sys_ioctl+0x91/0xa0
[ 9497.776897]  [<ffffffff815fc029>] system_call_fastpath+0x16/0x1b
[ 9497.776902] ---[ end trace 22886c442489082d ]---

The cause is due to calling kfree_skb() with interrupts disabled.

This bug is discussed in https://bugzilla.redhat.com/show_bug.cgi?id=797709.

Reported-and-Tested by: Ivan Ivanovich <iivanich@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoMerge branch 'for-john' of git://git.sipsolutions.net/mac80211-next
John W. Linville [Tue, 26 Jun 2012 18:27:34 +0000 (14:27 -0400)]
Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

12 years agowlcore: print stack trace in every recovery
Eyal Shapira [Tue, 26 Jun 2012 07:41:17 +0000 (10:41 +0300)]
wlcore: print stack trace in every recovery

As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: queue recovery in case of bus errors during cmd_remove_peer
Eyal Shapira [Tue, 26 Jun 2012 07:41:16 +0000 (10:41 +0300)]
wlcore: queue recovery in case of bus errors during cmd_remove_peer

Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.

Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: fix broken TX due to wrong queuing of recovery
Eyal Shapira [Tue, 26 Jun 2012 07:41:15 +0000 (10:41 +0300)]
wlcore: fix broken TX due to wrong queuing of recovery

commit 14bba17b "wl12xx: Propagate errors from wl1271_raw_write32"
breaks down TX in certain scenarios. wl1271_irq_locked() propagates
errors from wl1271_tx_work_locked however it may return -EBUSY
when the FW queues are full which is a legitimate case and not a
a real error. In this case a recovery is triggered by wl1271_irq
and this keeps repeating itself so TX is completely broken.
Fix it by avoiding propagating return values as errors even if they
aren't. Only bus (SDIO or SPI) ops failures would be progagated
as only these should trigger recovery.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: fix some failure cases in wlcore_probe()
Luciano Coelho [Mon, 25 Jun 2012 11:41:20 +0000 (14:41 +0300)]
wlcore: fix some failure cases in wlcore_probe()

We need to release the IRQ if hw_info() or identify_chip() fails.  And
we need unregister the HW with mac80211 if there are any failures
after it's registered.

Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: deprecate PG1 support
Luciano Coelho [Mon, 25 Jun 2012 11:15:55 +0000 (14:15 +0300)]
wl18xx: deprecate PG1 support

The new PG2 version of the chip has a few differences in terms of FW
API if compared to PG1.  PG1 is just a sample that shouldn't be used
in real life, so to avoid having to handle both separately, mark the
PG1 version as deprecated and bail out during probe.

Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agomac80211: make ieee80211_check_concurrent_iface netdev-independent
Johannes Berg [Tue, 19 Jun 2012 13:54:05 +0000 (15:54 +0200)]
mac80211: make ieee80211_check_concurrent_iface netdev-independent

ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: remove unused function
Johannes Berg [Tue, 19 Jun 2012 14:16:22 +0000 (16:16 +0200)]
mac80211: remove unused function

Remove the unused function is_ieee80211_device().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agonl80211: specify RSSI threshold in scheduled scan
Thomas Pedersen [Thu, 21 Jun 2012 18:09:54 +0000 (11:09 -0700)]
nl80211: specify RSSI threshold in scheduled scan

Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.

Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211_hwsim: fix smatch/sparse complaints
Johannes Berg [Mon, 25 Jun 2012 12:46:44 +0000 (14:46 +0200)]
mac80211_hwsim: fix smatch/sparse complaints

The code is fine in both cases as-is, but we can
write it slightly differently to fix smatch/sparse
complaints:
 * compare the skb pointer (which we use as a cookie)
   by casting the skb to unsigned long rather than the
   cookie to a pointer (fixes "different address spaces")
 * when transmitting, data->channel must be assigned,
   don't check it (fixes "dereferenced before check")

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: trace debug messages
Johannes Berg [Fri, 22 Jun 2012 11:36:25 +0000 (13:36 +0200)]
mac80211: trace debug messages

It can be very useful to have all debug messages
available when debugging, but hard to correlate
between different sources, so add a trace event
for all mac80211 debug messages.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: rename driver-trace file
Johannes Berg [Fri, 22 Jun 2012 10:55:52 +0000 (12:55 +0200)]
mac80211: rename driver-trace file

This file will contain more soon, so
rename it to just trace.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: clean up debugging
Johannes Berg [Fri, 22 Jun 2012 09:29:50 +0000 (11:29 +0200)]
mac80211: clean up debugging

There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agowlcore: prevent recovery in the middle of resume
Arik Nemtsov [Thu, 21 Jun 2012 15:10:52 +0000 (18:10 +0300)]
wlcore: prevent recovery in the middle of resume

Take the mutex early in the resume handler and use the locked version of
the IRQ routine. This ensures any recoveries queued will only take place
after resume has fully completed.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: refactor threaded IRQ routine
Arik Nemtsov [Thu, 21 Jun 2012 15:10:51 +0000 (18:10 +0300)]
wlcore: refactor threaded IRQ routine

Separate the threaded IRQ handling routine into two functions.
The outer function takes the mutex and calls recovery on errors. It also
performs a Tx-path optimization to avoid redundant works.

The inner function is simplified - all calls to recovery are removed and
it assumes the lock is taken. The locked variant will be reused elsewhere.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: check Rx-filter functions in the suspend path
Arik Nemtsov [Thu, 21 Jun 2012 15:10:50 +0000 (18:10 +0300)]
wlcore: check Rx-filter functions in the suspend path

Propagate some missing return values for Rx-filter related functions.
This and makes sure we always fail the suspend in case of SDIO errors.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: force recovery on resume if suspended without recovering
Arik Nemtsov [Thu, 21 Jun 2012 15:10:49 +0000 (18:10 +0300)]
wlcore: force recovery on resume if suspended without recovering

If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.

Detect this in the resume op and re-queue a recovery.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: don't allow SDIO read/writes after failure
Arik Nemtsov [Thu, 21 Jun 2012 15:10:48 +0000 (18:10 +0300)]
wlcore: don't allow SDIO read/writes after failure

Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.

This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted.  By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.

[Added second paragraph explaining why the change is needed. -- Luca]

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: cancel suspend when recovery is pending
Arik Nemtsov [Thu, 21 Jun 2012 15:10:47 +0000 (18:10 +0300)]
wlcore: cancel suspend when recovery is pending

We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: access the firmware memory via debugfs
Arkady Miasnikov [Mon, 18 Jun 2012 13:21:12 +0000 (16:21 +0300)]
wlcore: access the firmware memory via debugfs

Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event

Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem

[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]

Signed-off-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agortlwifi: Change debug level for deletion of an entry in CAM
Larry Finger [Thu, 21 Jun 2012 18:08:04 +0000 (13:08 -0500)]
rtlwifi: Change debug level for deletion of an entry in CAM

When running in AP mode, the driver reports all deletions from CAM in
a cryptic manner that makes users think it is an error. change so that
the condition is only reported at higher-levels of debugging.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_hw: fix smatch warning in ar9003_hw_spur_mitigate_mrc_cck
Rajkumar Manoharan [Thu, 21 Jun 2012 15:04:00 +0000 (20:34 +0530)]
ath9k_hw: fix smatch warning in ar9003_hw_spur_mitigate_mrc_cck

drivers/net/wireless/ath/ath9k/ar9003_phy.c:211
ar9003_hw_spur_mitigate_mrc_cck() error: potential NULL dereference
'spur_fbin_ptr'.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_hw: rename mrcCCKOff to fix smatch warning
Rajkumar Manoharan [Thu, 21 Jun 2012 15:03:59 +0000 (20:33 +0530)]
ath9k_hw: rename mrcCCKOff to fix smatch warning

Rename mrcCCKOff for better code readability and also fixes
the smatch warning.

drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
ar9003_hw_ani_control() Error invalid range 1 to 0.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmsmac: fix NULL pointer crash in brcms_c_regd_init()
Arend van Spriel [Thu, 21 Jun 2012 13:49:13 +0000 (15:49 +0200)]
brcmsmac: fix NULL pointer crash in brcms_c_regd_init()

In the function brcms_c_regd_init() the channels are validated
against the device capabilities. This is done for both 2.4G and
5G band, but there are devices that are 2.4G only, ie. BCM4313.
For that device this leads to a NULL dereference. This patch adds
a check in brcms_c_regd_init() to fix this.

Issue introduced in wireless-next tree by following commit:
cf03c5d brcm80211: smac: inform mac80211 of the X2 regulatory domain

Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agobrcmfmac: make inclusion of vmalloc.h explicit fixing linux-next build
Arend van Spriel [Thu, 21 Jun 2012 09:33:32 +0000 (11:33 +0200)]
brcmfmac: make inclusion of vmalloc.h explicit fixing linux-next build

This patch fixes problem detected in linux-next build for powerpc
allyesconfig. The error message below is no longer observed:

  CC      drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c: In function 'brcmf_sdio_dump_console':
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: error: implicit declaration of function 'vzalloc'
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: warning: assignment makes pointer from integer without a cast
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3113: error: implicit declaration of function 'vfree'
make[2]: *** [drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o] Error 1

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agomwifiex: enhance power save for USB and PCIe chipsets
Amitkumar Karwar [Thu, 21 Jun 2012 02:58:37 +0000 (19:58 -0700)]
mwifiex: enhance power save for USB and PCIe chipsets

FW will not explicitly notify about host sleep activation to the
host for USB and PCIe chipsets. Hence host should generate Host
Sleep Activated event as soon as Host Sleep parameters are
configured to FW successfully.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agomwifiex: wake up main thread to handle Tx traffic if scan is delayed/aborted
Amitkumar Karwar [Thu, 21 Jun 2012 02:58:36 +0000 (19:58 -0700)]
mwifiex: wake up main thread to handle Tx traffic if scan is delayed/aborted

This is a flaw in recently implemented logic to handle Tx traffic
and scan operation simultaneously. We missed to wakeup main thread
to handle Tx traffic if scan is delayed/aborted.

For some cards (SD8797, for example), firmware will send SLEEP event
if there is no activity for 50msec. While handling the SLEEP event,
main thread will be woken up and Tx packet gets sent hence. In worst
case Tx traffic will be delayed for 50msec.

For other cards, such as USB8797, firmware won't send SLEEP event.
So, Tx traffic gets stuck if no other event triggers the wakeup of
main thread.

This patch fixes above issues.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agomwifiex: parse WPA IE and support WPA/WPA2 mixed mode for uAP
Avinash Patil [Fri, 15 Jun 2012 19:21:52 +0000 (12:21 -0700)]
mwifiex: parse WPA IE and support WPA/WPA2 mixed mode for uAP

Add support for parsing WPA IE from beacon parameter of
cfg80211_ap_settings and set it to FW.

WPA/WPA2 mixed mode is supported with this patch.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoMerge branch 'for-linville' of git://git.kernel.org/pub/scm/linux/kernel/git/luca...
John W. Linville [Fri, 22 Jun 2012 18:41:57 +0000 (14:41 -0400)]
Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

12 years agoMerge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi...
John W. Linville [Fri, 22 Jun 2012 18:40:38 +0000 (14:40 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

12 years agoMerge branch 'for-john' of git://git.sipsolutions.net/mac80211-next
John W. Linville [Fri, 22 Jun 2012 18:39:53 +0000 (14:39 -0400)]
Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

12 years agomac80211: pass sdata to some RX functions
Johannes Berg [Fri, 22 Jun 2012 10:48:38 +0000 (12:48 +0200)]
mac80211: pass sdata to some RX functions

For better debugging, we would like to have
the sdata pointer available later, so pass
it into these functions.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: two small verbose debug cleanups
Johannes Berg [Fri, 22 Jun 2012 09:37:03 +0000 (11:37 +0200)]
mac80211: two small verbose debug cleanups

Two instances of CONFIG_MAC80211_VERBOSE_DEBUG
should be different, fix them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: remove TKIP debug
Johannes Berg [Fri, 22 Jun 2012 09:26:47 +0000 (11:26 +0200)]
mac80211: remove TKIP debug

The TKIP code hasn't been changed in a very long
time, so it seems unlikely that anyone really has
a need for the TKIP debug code. Remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agowlcore: Force checking of io functions' return values
Ido Yariv [Tue, 19 Jun 2012 21:03:46 +0000 (00:03 +0300)]
wlcore: Force checking of io functions' return values

All io functions' return values should be propagated and handled. Add a
__must_check annotation to verify that the return values are checked and
to avoid future mistakes.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Propagate errors from wl1271_read_hwaddr
Ido Yariv [Mon, 18 Jun 2012 15:15:50 +0000 (18:15 +0300)]
wlcore: Propagate errors from wl1271_read_hwaddr

Propagate errors from wl1271_read_hwaddr. This function is only used
when reading the FW log (following a recovery), so don't read the FW log
in case of a bus error.

Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Propagate errors from wl1271_raw_write32
Ido Yariv [Tue, 19 Jun 2012 21:48:23 +0000 (00:48 +0300)]
wlcore: Propagate errors from wl1271_raw_write32

Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Propagate errors from wl1271_raw_read32
Ido Yariv [Mon, 18 Jun 2012 12:50:21 +0000 (15:50 +0300)]
wlcore: Propagate errors from wl1271_raw_read32

Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Propagate errors from wl1271_write
Ido Yariv [Mon, 18 Jun 2012 10:21:55 +0000 (13:21 +0300)]
wlcore: Propagate errors from wl1271_write

Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Propagate errors from wl1271_read
Ido Yariv [Mon, 18 Jun 2012 09:31:16 +0000 (12:31 +0300)]
wlcore: Propagate errors from wl1271_read

Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Propagate errors from wlcore_raw_*_data functions
Ido Yariv [Sun, 17 Jun 2012 18:59:42 +0000 (21:59 +0300)]
wlcore: Propagate errors from wlcore_raw_*_data functions

wlcore_raw_read_data is called when the FW status is read which happens
while handling interrupts and when the FW log is read following a
recovery. Request a recovery in the former case, and don't read the FW
log in case the FW status read failed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Change raw io functions to return errors
Ido Yariv [Sun, 17 Jun 2012 18:29:51 +0000 (21:29 +0300)]
wlcore: Change raw io functions to return errors

Make wl1271_raw_write and wl1271_raw_read return errors so the driver
could handle these appropriately.
Since the prototype has changed, also rename the prefix of these
functions to wlcore.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Change read/write ops to return errors
Ido Yariv [Sun, 17 Jun 2012 17:30:05 +0000 (20:30 +0300)]
wlcore: Change read/write ops to return errors

While bus operations may fail, either due to HW or FW issues, these are
never propagated to higher layers. As a result, the core driver has no
way of knowing that the operations failed, and will only recover if high
level logic requires it (e.g. no command completion).

Change read/write bus operations to return errors to let higher layer
functionality handle these.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Disable interrupts while recovering
Ido Yariv [Sun, 20 May 2012 22:10:11 +0000 (01:10 +0300)]
wlcore: Disable interrupts while recovering

In case a recovery is initiated, the FW can no longer be trusted, and
the driver should not handle any new FW events.

Disable the interrupt handler when a recovery is scheduled and balance
it back in the op_stop callback.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: Fix sdio out-of-sync power state
Ido Yariv [Sun, 20 May 2012 07:38:16 +0000 (10:38 +0300)]
wlcore: Fix sdio out-of-sync power state

wl12xx_sdio_power_off() manually powers down the card regardless of the
runtime pm state. If wl12xx_sdio_power_on() is called before the card
was suspended by runtime PM, it will not power up the card.

As part of the HW detection, the chip's power is toggled. Since this
happens in the context of probing sdio, the power reference counter will
be higher than zero. As a result, when wl12xx_sdio_power_off() is
called, the chip will be powered down while still having a positive
power reference counter. If the interface is quickly activated, the
driver might try to transfer data to a powered off chip.

Fix this by ensuring that wl12xx_sdio_power_on() explicitly powers on
the chip in case runtime pm claims the chip is already powered on. To
avoid cases in which it is not possible to determine if the chip was
really powered on (card's power reference counter is positive), operate
on the mmc_card instead of the function.

Also verify that the chip is indeed powered on before powering off, to
avoid wrong reference counter values in error cases.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agoieee80211: more OUI type definitions for WLAN_OUI_MICROSOFT
Avinash Patil [Thu, 21 Jun 2012 00:59:01 +0000 (17:59 -0700)]
ieee80211: more OUI type definitions for WLAN_OUI_MICROSOFT

WMM and WPS

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agomac80211: add command to get current rssi
Victor Goldenshtein [Thu, 21 Jun 2012 07:56:46 +0000 (10:56 +0300)]
mac80211: add command to get current rssi

Get current rssi (in dBm) from the driver/FW.

Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agoMerge branch 'wl12xx-next' into for-linville
Luciano Coelho [Thu, 21 Jun 2012 14:31:46 +0000 (17:31 +0300)]
Merge branch 'wl12xx-next' into for-linville

Conflicts:
drivers/net/wireless/ti/wl18xx/main.c

12 years agowl18xx: use %zu for size_t arguments in printk calls
Luciano Coelho [Thu, 21 Jun 2012 12:33:10 +0000 (15:33 +0300)]
wl18xx: use %zu for size_t arguments in printk calls

After 934b9d1e (wl18xx: avoid some -Wformat warnings) there was still
a warning with (at least) ARM gcc version 4.4.1:

drivers/net/wireless/ti/wl18xx/main.c: In function 'wl18xx_conf_init':
drivers/net/wireless/ti/wl18xx/main.c:1026: warning: format '%ld' expects type 'long int', but argument 2 has type 'unsigned int'

Fix this by using %zu for the both formats, since the fw->size and the
macro (derived from sizeof()) are size_t.

Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: split siso40 HT cap between 2Ghz and 5Ghz
Arik Nemtsov [Wed, 13 Jun 2012 16:09:26 +0000 (19:09 +0300)]
wl18xx: split siso40 HT cap between 2Ghz and 5Ghz

Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: sane defaults for HT capabilities
Arik Nemtsov [Wed, 13 Jun 2012 16:09:25 +0000 (19:09 +0300)]
wl18xx: sane defaults for HT capabilities

Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.

Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.

Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: explicitly remove the 5Ghz MIMO HT cap
Arik Nemtsov [Wed, 13 Jun 2012 16:09:24 +0000 (19:09 +0300)]
wl18xx: explicitly remove the 5Ghz MIMO HT cap

The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: read FW logs from FW memory on watchdog recovery
Igal Chernobelsky [Mon, 18 Jun 2012 08:05:39 +0000 (11:05 +0300)]
wlcore: read FW logs from FW memory on watchdog recovery

FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.

FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is  equal to 0x2000000

Log data resides inside FW memory block with offset depending on
logger mode:
- on demand:  4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size

Described FW logger API is backward compatible with previous FW versions.

Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: do not report noise level in get survey op
Yoni Divinsky [Wed, 13 Jun 2012 15:56:54 +0000 (18:56 +0300)]
wlcore: do not report noise level in get survey op

The get survey op expects the low level driver to report
the noise level for a a given channel.

The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.

Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: set Tx align quirk for PG2
Arik Nemtsov [Mon, 11 Jun 2012 07:41:08 +0000 (10:41 +0300)]
wl18xx: set Tx align quirk for PG2

Before patch b5d6d9b (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowl18xx: increase Rx descriptors for PG2
Arik Nemtsov [Sun, 10 Jun 2012 19:57:30 +0000 (22:57 +0300)]
wl18xx: increase Rx descriptors for PG2

New PG2 firmwares have additional Rx descriptors.

Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: reconfigure sleep_auth when removing interfaces
Arik Nemtsov [Sun, 10 Jun 2012 16:10:45 +0000 (19:10 +0300)]
wlcore: reconfigure sleep_auth when removing interfaces

The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.

Take this opportunity to refactor the sleep_auth setting code for better
readability.

[Small style fix. -- Luca]

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: allow setting sleep_auth before interface init
Arik Nemtsov [Sun, 10 Jun 2012 14:09:22 +0000 (17:09 +0300)]
wlcore: allow setting sleep_auth before interface init

Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.

This makes debugging more intuitive using the debugfs value.

Increment the conf version since we added an element to the conf
structure.

Note: An AP going up will always set sleep_auth to PSM_CAM.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agowlcore: add a debugfs entry to allow changing the sleep mode by hand
Luciano Coelho [Tue, 28 Feb 2012 17:13:28 +0000 (19:13 +0200)]
wlcore: add a debugfs entry to allow changing the sleep mode by hand

For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want.  To allow
this, a debugfs entry is added.

Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
12 years agowlcore: suppress error message on Rx BA session removal
Arik Nemtsov [Wed, 6 Jun 2012 07:48:56 +0000 (10:48 +0300)]
wlcore: suppress error message on Rx BA session removal

The ampdu_action() function is called on the reconfig() path to remove
existing Rx BA sessions. Since these don't exist for the low level
driver, we output an error message. Turn the message into a debug
message for now, until the mac80211 reconfig flow is changed.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
12 years agoiwlwifi: limit mac_change_interface to BSS context
Johannes Berg [Wed, 20 Jun 2012 09:47:42 +0000 (11:47 +0200)]
iwlwifi: limit mac_change_interface to BSS context

Currently when mac80211 asks to change the interface
type, we will accept it for both the BSS and PAN
contexts. This is not terribly complicated today,
but with the addition of the P2P Device abstraction
the PAN context handling will get more complex, so
restrict mac_change_interface to the BSS context.

Also fix a small locking issue and use is_active
instead of the vif pointer to check if the other
context is activated, guarding exclusive interface
types on the BSS context (IBSS) against the PAN
context being used for something else.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agoiwlwifi: increase scan timeout
Johannes Berg [Wed, 20 Jun 2012 14:24:59 +0000 (16:24 +0200)]
iwlwifi: increase scan timeout

When the first interface is active, then scanning
on it or the second interface can take a little
longer than 7s (I observed around 8s.) Bump the
timeout to 15s to avoid aborting a scan that is
still running, just taking more time.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agoiwlwifi: fix radio reset scan dwell vs. quiet time
Johannes Berg [Wed, 20 Jun 2012 19:25:15 +0000 (21:25 +0200)]
iwlwifi: fix radio reset scan dwell vs. quiet time

My previous commit to shorten the radio reset time
caused issues as the firmware checks the active
dwell time against the quiet time, asserting that
the dwell is >= quiet time. This isn't really
needed in case of passive scanning like here, but
of course we need to pass that check.

To fix this, override the quiet time to be the
same as the radio reset dwell time.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
12 years agortlwifi: rtl8192se: Fix gcc 4.7.x warning
Larry Finger [Wed, 20 Jun 2012 16:47:26 +0000 (11:47 -0500)]
rtlwifi: rtl8192se: Fix gcc 4.7.x warning

With gcc 4.7.x, the following warning is issued as the routine that sets
the array has the possibility of not initializing the values:

  CC [M]  drivers/net/wireless/rtlwifi/rtl8192se/phy.o
drivers/net/wireless/rtlwifi/rtl8192se/phy.c: In function ‘rtl92s_phy_set_txpower’:
drivers/net/wireless/rtlwifi/rtl8192se/phy.c:1268:23: warning: ‘ofdmpowerLevel[0]’ may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: do not sampling on ani timer when chip is in sleep
Rajkumar Manoharan [Tue, 19 Jun 2012 09:20:28 +0000 (14:50 +0530)]
ath9k: do not sampling on ani timer when chip is in sleep

The baseband and cycle counters are being sampled during ani
processing for debugging purpose. Whenever the ani is postponded
due to sleep state, taking samples on that time is of no use and
also unneccesarily waking up the chip might increase the power
consumption on idle associated state. Hence moving debug function
within powersave block.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_hw: fix LNA control on WLAN sleep
Rajkumar Manoharan [Mon, 18 Jun 2012 13:32:40 +0000 (19:02 +0530)]
ath9k_hw: fix LNA control on WLAN sleep

When WLAN enter full sleep mode, WLAN HW should send out a LNA_TAKE
message for BT to take control of the shared LNA. Otherwise BT traffic
is completely stopped whenever the wlan interface is moved full sleep
mode.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_hw: update ar9462 dac_async_fifo initval
Rajkumar Manoharan [Mon, 18 Jun 2012 13:32:39 +0000 (19:02 +0530)]
ath9k_hw: update ar9462 dac_async_fifo initval

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: fix mci_is_enabled utility
Rajkumar Manoharan [Mon, 18 Jun 2012 13:32:38 +0000 (19:02 +0530)]
ath9k: fix mci_is_enabled utility

During driver stop, btcoex is disabled and also btcoex_hw.enabled
is set to false. Afterwards mci_is_enabled returns false so that
BT is not gaining SPDT control on WLAN sleep. Fix that.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k_hw: fix BT mute at hw init
Rajkumar Manoharan [Mon, 18 Jun 2012 13:32:37 +0000 (19:02 +0530)]
ath9k_hw: fix BT mute at hw init

WLAN driver initialization is muting BT which is terminating
the ongoing BT traffic. The reason to mute BT is to avoid any
incoming MCI messages from BT when MCI reset is in progress that
could corrupt WLAN MCI RX state machine. But we should not
dedicate radio completely to WLAN in driver init itself. So this
patch removes the wlan weightage changes from mute BT to retain
BT connection.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agoath9k: fix incorrect profile type manupulation
Bala Shanmugam [Mon, 18 Jun 2012 06:06:58 +0000 (11:36 +0530)]
ath9k: fix incorrect profile type manupulation

Two MCI interrupts are generated while adding A2DP and headset profiles
with different types and same connection handle. While disconnecting,
only one MCI interrupt is generated with last added profile type value
for both profiles.

While adding second profile type decrement first one.

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agowl1251: send filters to firmware as they are set
Grazvydas Ignotas [Sat, 16 Jun 2012 19:31:50 +0000 (22:31 +0300)]
wl1251: send filters to firmware as they are set

Firmware supports changing filters using ACX_RX_CFG command,
so use it in .configure_filter callback. Firmware also supports
probe request filtering, so add it too along the way.
This will also re-enable BSSID filter which is now removed by
join command while associating.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agowl1251: fix filtering support
Grazvydas Ignotas [Sat, 16 Jun 2012 19:31:49 +0000 (22:31 +0300)]
wl1251: fix filtering support

This driver has a hack in cmd.c which effectively disables all filtering.
This seems to be triggering a firmware bug where it stops reporting any
rx packets after random time on some routers, which is eliminated (or at
least appears much more rarely) when filtering is on.
I have found that only BSSID filter needs to be disabled for association
to work, so disable only that instead of all filtering.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
12 years agowl1251: remove unused filter_work
Grazvydas Ignotas [Sat, 16 Jun 2012 19:31:48 +0000 (22:31 +0300)]
wl1251: remove unused filter_work

filter_work is never used, remove it.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>