usb: renesas_usbhs: Use dmac only if the pipe type is bulk

commit 700aa7ff8d2c2b9cc669c99375e2ccd06d3cd38d upstream.

This patch fixes an issue that isochronous transfer's data is possible to
be lost as a workaround. Since this driver uses a workqueue to start
the dmac, the transfer is possible to be delayed when system load is high.

Fixes: 6e4b74e4690d ("usb: renesas: fix scheduling in atomic context bug")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: renesas_usbhs: clear the BRDYSTS in usbhsg_ep_enable()

commit 9ab967e6db7412b675ecbff80d5371d53c82cb2e upstream.

This patch fixes an issue that unexpected BRDY interruption happens
when the usb_ep_{enable,disable}() are called with different direction.
In this case, the driver will cause the following message:

 renesas_usbhs e6590000.usb: irq_ready run_error 1 : -16

This issue causes the followings:
 1) A pipe is enabled as transmission
 2) The pipe sent a data
 3) The pipe is disabled and re-enabled as reception.
 4) The pipe got a queue

Since the driver doesn't clear the BRDYSTS flags after 2) above, the issue
happens. If we add such clearing the flags into the driver, the code will
become complicate. So, this patch clears the BRDYSTS flag of reception in
usbhsg_ep_enable() to avoid complicate.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: hub: change the locking in hub_activate

commit 07d316a22e119fa301fd7dba7f1e1adfd4f72c05 upstream.

The locking in hub_activate() is not adequate to provide full mutual
exclusion with hub_quiesce().  The subroutine locks the hub's
usb_interface, but the callers of hub_quiesce() (such as
hub_pre_reset() and hub_event()) hold the lock to the hub's
usb_device.

This patch changes hub_activate() to make it acquire the same lock as
those other routines.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: hub: fix up early-exit pathway in hub_activate

commit ca5cbc8b02f9b21cc8cd1ab36668763ec34f9ee8 upstream.

The early-exit pathway in hub_activate, added by commit e50293ef9775
("USB: fix invalid memory access in hub_activate()") needs
improvement.  It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.

This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine.  It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub: Fix unbalanced reference count/memory leak/deadlocks

commit 6bb47e8ab98accb1319bd43c64966340ba3bba9a upstream.

Memory leak and unbalanced reference count:

If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.

This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.

kmemleak reports this as (with the commit e50293ef9775 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):

unreferenced object 0xffffffc08af5b800 (size 1024):
  comm "khubd", pid 73, jiffies 4295051211 (age 6482.350s)
  hex dump (first 32 bytes):
    30 68 f3 8c c0 ff ff ff 00 a0 b2 2e c0 ff ff ff  0h..............
    01 00 00 00 00 00 00 00 00 94 7d 40 c0 ff ff ff  ..........}@....
  backtrace:
    [<ffffffc0003079ec>] create_object+0x148/0x2a0
    [<ffffffc000cc150c>] kmemleak_alloc+0x80/0xbc
    [<ffffffc000303a7c>] kmem_cache_alloc_trace+0x120/0x1ac
    [<ffffffc0006fa610>] hub_probe+0x120/0xb84
    [<ffffffc000702b20>] usb_probe_interface+0x1ec/0x298
    [<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
    [<ffffffc0005d5308>] __device_attach+0x28/0x4c
    [<ffffffc0005d3164>] bus_for_each_drv+0x78/0xac
    [<ffffffc0005d4ee0>] device_attach+0x6c/0x9c
    [<ffffffc0005d42b8>] bus_probe_device+0x28/0xa0
    [<ffffffc0005d23a4>] device_add+0x324/0x604
    [<ffffffc000700fcc>] usb_set_configuration+0x660/0x6cc
    [<ffffffc00070a350>] generic_probe+0x44/0x84
    [<ffffffc000702914>] usb_probe_device+0x54/0x74
    [<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
    [<ffffffc0005d5308>] __device_attach+0x28/0x4c

Deadlocks:

If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.

Fix both the issues by removing the call to cancel_delayed_work_sync().

Fixes: e50293ef9775 ("USB: fix invalid memory access in hub_activate()")
Reported-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: define USB_SPEED_SUPER_PLUS speed for SuperSpeedPlus USB3.1 devices

commit 8a1b2725a60d3267135c15e80984b4406054f650 upstream.

Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: increment request->actual once

commit c7de573471832dff7d31f0c13b0f143d6f017799 upstream.

When using SG lists, we would end up setting
request->actual to:

num_mapped_sgs * (request->length - count)

Let's fix that up by incrementing request->actual
only once.

Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: pci: add Intel Kabylake PCI ID

commit 4491ed5042f0419b22a4b08331adb54af31e2caa upstream.

Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: usbtest: add fix for driver hang

commit 539587511835ea12d8daa444cbed766cf2bc3612 upstream.

In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.

This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci: change order of register cleanup during shutdown

commit bc337b51508beb2d039aff5074a76cfe1c212030 upstream.

In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.

This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.

Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: caam - defer aead_set_sh_desc in case of zero authsize

commit 2fdea258fde036a87d3396ec9c0ef66f10768530 upstream.

To be able to generate shared descriptors for AEAD, the authentication size
needs to be known. However, there is no imposed order of calling .setkey,
.setauthsize callbacks.

Thus, in case authentication size is not known at .setkey time, defer it
until .setauthsize is called.

The authsize != 0 check was incorrectly removed when converting the driver
to the new AEAD interface.

Fixes: 479bcc7c5b9e ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: caam - fix echainiv(authenc) encrypt shared descriptor

commit 1d2d87e81ea21f64c19b95ef228b865a6880e17e upstream.

There are a few things missed by the conversion to the
new AEAD interface:

1 - echainiv(authenc) encrypt shared descriptor

The shared descriptor is incorrect: due to the order of operations,
at some point in time MATH3 register is being overwritten.

2 - buffer used for echainiv(authenc) encrypt shared descriptor

Encrypt and givencrypt shared descriptors (for AEAD ops) are mutually
exclusive and thus use the same buffer in context state: sh_desc_enc.

However, there's one place missed by s/sh_desc_givenc/sh_desc_enc,
leading to errors when echainiv(authenc(...)) algorithms are used:
DECO: desc idx 14: Header Error. Invalid length or parity, or
certain other problems.

While here, also fix a typo: dma_mapping_error() is checking
for validity of sh_desc_givenc_dma instead of sh_desc_enc_dma.

Fixes: 479bcc7c5b9e ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: caam - fix non-hmac hashes

commit a0118c8b2be9297aed8e915c60b4013326b256d4 upstream.

Since 6de62f15b581 ("crypto: algif_hash - Require setkey before
accept(2)"), the AF_ALG interface requires userspace to provide a key
to any algorithm that has a setkey method.  However, the non-HMAC
algorithms are not keyed, so setting a key is unnecessary.

Fix this by removing the setkey method from the non-keyed hash
algorithms.

Fixes: 6de62f15b581 ("crypto: algif_hash - Require setkey before accept(2)")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq/msi: Make sure PCI MSIs are activated early

commit f3b0946d629c8bfbd3e5f038e30cb9c711a35f10 upstream.

Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).

It turns out that the two MSI paths in the kernel are doing slightly different
things:

generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI

And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled.  In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.

In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.

A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.

tglx:

 - Several people reported a VMWare regression with PCI/MSI-X passthrough. It
   turns out that the patch also cures that issue.

 - We need to have a look at the MSI disable interrupt path, where we write
   the msg to all zeros without disabling MSI in the PCI device. Is that
   correct?

Fixes: 52f518a3a7c2 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq/msi: Remove unused MSI_FLAG_IDENTITY_MAP

commit b6140914fd079e43ea75a53429b47128584f033a upstream.

No user and we definitely don't want to grow one.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-2-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

um: Don't discard .text.exit section

commit dad2232844073295c64e9cc2d734a0ade043e0f6 upstream.

Commit e41f501d3912 ("vmlinux.lds: account for destructor sections")
added '.text.exit' to EXIT_TEXT which is discarded at link time by default.
This breaks compilation of UML:
     `.text.exit' referenced in section `.fini_array' of
     /usr/lib/gcc/x86_64-linux-gnu/6/../../../x86_64-linux-gnu/libc.a(sdlerror.o):
     defined in discarded section `.text.exit' of
     /usr/lib/gcc/x86_64-linux-gnu/6/../../../x86_64-linux-gnu/libc.a(sdlerror.o)

Apparently UML doesn't want to discard exit text, so let's place all EXIT_TEXT
sections in .exit.text.

Fixes: e41f501d3912 ("vmlinux.lds: account for destructor sections")
Reported-by: Stefan Traby <stefan@hello-penguin.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / CPPC: Prevent cpc_desc_ptr points to the invalid data

commit 2324d15447a9db168b1f85e3feac635b1ff8edb8 upstream.

When CPPC fails to request a PCC channel, the CPC data is freed
and cpc_desc_ptr points to the invalid data.

Avoid this issue by moving the cpc_desc_ptr assignment after the PCC
channel request.

Signed-off-by: Hoan Tran <hotran@apm.com>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI: CPPC: Return error if _CPC is invalid on a CPU

commit 8343c40d3de32ebfe8f48b043964e4ba0e7701f7 upstream.

Based on 8.4.7.1 section of ACPI 6.1 specification, if the platform
supports CPPC, the _CPC object must exist under all processor objects.
If cpc_desc_ptr pointer is invalid on any CPUs, acpi_get_psd_map()
should return error and CPPC cpufreq driver can not be registered.

Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-acpi: Reduce Baytrail eMMC/SD/SDIO hangs

commit 6e1c7d6103fe7031035cec321307c6356809adf4 upstream.

Baytrail eMMC/SD/SDIO host controllers have been known to
hang.  A change to a hardware setting has been found to
reduce the occurrence of such hangs.  This patch ensures
the correct setting.

This patch applies cleanly to v4.4+.  It could go to
earlier kernels also, so I will send backports to the
stable list in due course.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Limit config space size for Netronome NFP4000

commit c2e771b02792d222cbcd9617fe71482a64f52647 upstream.

Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI
config space addresses above 0x600 can cause the NFP to generate PCIe
completion timeouts.

Limit the NFP4000's PF's config space size to 0x600 bytes as is already
done for the NFP6000.

The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF.  Thus, its config space is already limited
by the existing use of quirk_nfp6000().

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Add Netronome NFP4000 PF device ID

commit 69874ec233871a62e1bc8c89e643993af93a8630 upstream.

Add the device ID for the PF of the NFP4000.  The device ID for the VF,
0x6003, is already present as PCI_DEVICE_ID_NETRONOME_NFP6000_VF.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Limit config space size for Netronome NFP6000 family

commit 9f33a2ae59f24452c1076749deb615bccd435ca9 upstream.

The NFP6000 has an erratum where reading/writing to PCI config space
addresses above 0x600 can cause the NFP to generate PCIe completion
timeouts.

Limit the NFP6000's config space size to 0x600 bytes.

Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Add Netronome vendor and device IDs

commit a755e169031dac9ebaed03302c4921687c271d62 upstream.

Device IDs for the Netronome NFP3200, NFP3240, NFP6000, and NFP6000 SR-IOV
devices.

Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Support PCIe devices with short cfg_size

commit c20aecf6963d1273d8f6d61c042b4845441ca592 upstream.

If a device quirk modifies the pci_dev->cfg_size to be less than
PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256),
the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE.

Allow sysfs access to config space up to cfg_size, even if the device
doesn't support the entire 4096-byte PCIe config space.

Note that pci_read_config() and pci_write_config() limit access to
dev->cfg_size even though pcie_config_attr contains 4096 (the maximum
size).

Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
[bhelgaas: more changelog edits]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NVMe: Don't unmap controller registers on reset

Commit b00a726a9fd82ddd4c10344e46f0d371e1674303 upstream.

Unmapping the registers on reset or shutdown is not necessary. Keeping
the mapping simplifies reset handling.

This was backported to 4.4 stable tree because it prevents a race
between the reset_work and the shutdown hook, that may provoke the Oops
below, in the nvme_wait_ready function.

The Oops is easily reproducible on systems that will kexec/reboot
immediately after booting, which is actually the common use case for
kexec based bootloaders, like Petitboot.  This patch removes the
unnecessary early unmapping of the PCI configuration in the shutdown
hook, allowing a proper handling of the reset work.

Unable to handle kernel paging request for data at address 0x0000001c
Faulting instruction address: 0xd000000000720b38
cpu 0x1b: Vector: 300 (Data Access) at [c000007f7a9a38a0]
    pc: d000000000720b38: nvme_wait_ready+0x50/0x120 [nvme]
    lr: d000000000720b7c: nvme_wait_ready+0x94/0x120 [nvme]
    sp: c000007f7a9a3b20
   msr: 9000000000009033
   dar: 1c
 dsisr: 40000000
  current = 0xc000007f7a926c80
  paca    = 0xc00000000fe85100   softe: 0        irq_happened: 0x01
    pid   = 2608, comm = kworker/27:1
enter ? for help
[c000007f7a9a3bb0] d00000000072572c nvme_setup_io_queues+0xc08/0x1218 [nvme]
[c000007f7a9a3c70] c00000000006bbd8 process_one_work+0x228/0x378
[c000007f7a9a3d00] c00000000006c050 worker_thread+0x2e0/0x420
[c000007f7a9a3d80] c00000000007161c kthread+0xfc/0x108
[c000007f7a9a3e30] c0000000000094b4 ret_from_kernel_thread+0x5c/0xa8

Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
[Backport to v4.4.y]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Manage power well properly for resume

commit a52ff34e5ec61749c62c6618b76a9d6dbecee450 upstream.

For SKL and later Intel chips, we control the power well per codec
basis via link_power callback since the commit [03b135cebc47: ALSA:
hda - remove dependency on i915 power well for SKL].
However, there are a few exceptional cases where the gfx registers are
accessed from the audio driver: namely the wakeup override bit
toggling at (both system and runtime) resume.  This seems causing a
kernel warning when accessed during the power well down (and likely
resulting in the bogus register accesses).

This patch puts the proper power up / down sequence around the resume
code so that the wakeup bit is fiddled properly while the power is
up.  (The other callback, sync_audio_rate, is used only in the PCM
callback, so it's guaranteed in the power-on.)

Also, by this proper power up/down, the instantaneous flip of wakeup
bit in the resume callback that was introduced by the commit
[033ea349a7cd: ALSA: hda - Fix Skylake codec timeout] becomes
superfluous, as snd_hdac_display_power() already does it.  So we can
clean it up together.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214
Fixes: 03b135cebc47 ('ALSA: hda - remove dependency on i915 power well for SKL')
Cc: <stable@vger.kernel.org> # v4.2+
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libnvdimm, nd_blk: mask off reserved status bits

commit 68202c9f0ad6e16ee806fbadbc5838d55fe5aa5c upstream.

The "NVDIMM Block Window Driver Writer's Guide":

    http://pmem.io/documents/NVDIMM_DriverWritersGuide-July-2016.pdf

...defines the layout of the block window status register.  For the July
2016 version of the spec linked to above, this happens in Figure 4 on
page 26.

The only bits defined in this spec are bits 31, 5, 4, 2, 1 and 0.  The
rest of the bits in the status register are reserved, and there is a
warning following the diagram that says:

    Note: The driver cannot assume the value of the RESERVED bits in the
    status register are zero. These reserved bits need to be masked off, and
    the driver must avoid checking the state of those bits.

This change ensures that for hardware implementations that set these
reserved bits in the status register, the driver won't incorrectly fail the
block I/Os.

Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix occasional decoding errors when tracing system-wide

commit 3d918fb13abdbeca7947578f5d7e426eafad7f5e upstream.

In order to successfully decode Intel PT traces, context switch events
are needed from the moment the trace starts. Currently that is ensured
by using the 'immediate' flag which enables the switch event when it is
opened.

However, since commit 86c2786994bd ("perf intel-pt: Add support for
PERF_RECORD_SWITCH") that might not always happen. When tracing
system-wide the context switch event is added to the tracking event
which was not set as 'immediate'. Change that so it is.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 86c2786994bd ("perf intel-pt: Add support for PERF_RECORD_SWITCH")
Link: http://lkml.kernel.org/r/1471245784-22580-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfio/pci: Fix NULL pointer oops in error interrupt setup handling

commit c8952a707556e04374d7b2fdb3a079d63ddf6f2f upstream.

There are multiple cases in vfio_pci_set_ctx_trigger_single() where
we assume we can safely read from our data pointer without actually
checking whether the user has passed any data via the count field.
VFIO_IRQ_SET_DATA_NONE in particular is entirely broken since we
attempt to pull an int32_t file descriptor out before even checking
the data type.  The other data types assume the data pointer contains
one element of their type as well.

In part this is good news because we were previously restricted from
doing much sanitization of parameters because it was missed in the
past and we didn't want to break existing users.  Clearly DATA_NONE
is completely broken, so it must not have any users and we can fix
it up completely.  For DATA_BOOL and DATA_EVENTFD, we'll just
protect ourselves, returning error when count is zero since we
previously would have oopsed.

Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Chris Thompson <the_cartographer@hotmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio: fix memory leak in virtqueue_add()

commit 58625edf9e2515ed41dac2a24fa8004030a87b87 upstream.

When using the indirect buffers feature, 'desc' is allocated in
virtqueue_add() but isn't freed before leaving on a ring full error,
causing a memory leak.

For example, it seems rather clear that this can trigger
with virtio net if mergeable buffers are not used.

Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix order of EREFUSED define in errno.h

commit 3eb53b20d7bd1374598cfb1feaa081fcac0e76cd upstream.

When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.

Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.

Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO

commit 3146bc64d12377a74dbda12b96ea32da3774ae07 upstream.

AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for arm64 at all even though ARCH_DLINFO will contain one NEW_AUX_ENT
for the VDSO address.

This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which arm64 doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.

Fixes: f668cd1673aa ("arm64: ELF definitions")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Add quirk for ELP HD USB Camera

commit 41f5e3bdbf706a9e98194bf0c4b62a875c02f170 upstream.

The ELP HD USB Camera (05a3:9420) needs this quirk for suppressing
the unsupported sample rate inquiry.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Add a sample rate quirk for Creative Live! Cam Socialize HD (VF0610)

commit 7627e40c66b5547e12b6c5673646ceea84797a74 upstream.

VF0610 does not support reading the sample rate which leads to many
lines of "cannot get freq at ep 0x82". This patch adds the USB ID
(0x041E:4080) to snd_usb_get_sample_rate_quirk() list.

Signed-off-by: Piotr Karasinski <peter.karasinski@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/eeh: eeh_pci_enable(): fix checking of post-request state

commit 949e9b827eb4736d96df520c67d07a54c64e99b8 upstream.

In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.

At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.

On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.

On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.

Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.

Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.

Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SUNRPC: allow for upcalls for same uid but different gss service

commit 9130b8dbc6ac20f2dc5846e1647f5b60eafab6e3 upstream.

It's possible to have simultaneous upcalls for the same UIDs but
different GSS service. In that case, we need to allow for the
upcall to gssd to proceed so that not the same context is used
by two different GSS services. Some servers lock the use of context
to the GSS service.

Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SUNRPC: Handle EADDRNOTAVAIL on connection failures

commit 1f4c17a03ba7f430d63dba8c8e08ff1e2712581d upstream.

If the connect attempt immediately fails with an EADDRNOTAVAIL error, then
that means our choice of source port number was bad.
This error is expected when we set the SO_REUSEPORT socket option and we
have 2 sockets sharing the same source and destination address and port
combinations.

Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 402e23b4ed9ed ("SUNRPC: Fix stupid typo in xs_sock_set_reuseport")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools/testing/nvdimm: fix SIGTERM vs hotplug crash

commit d8d378fa1a0c98ecb50ca52c9bf3bc14e25aa2d2 upstream.

The unit tests crash when hotplug races the previous probe. This race
requires that the loading of the nfit_test module be terminated with
SIGTERM, and the module to be unloaded while the ars scan is still
running.

In contrast to the normal nfit driver, the unit test calls
acpi_nfit_init() twice to simulate hotplug, whereas the nominal case
goes through the acpi_nfit_notify() event handler.  The
acpi_nfit_notify() path is careful to flush the previous region
registration before servicing the hotplug event. The unit test was
missing this guarantee.

 BUG: unable to handle kernel NULL pointer dereference at           (null)
 IP: [<ffffffff810cdce7>] pwq_activate_delayed_work+0x47/0x170
 [..]
 Call Trace:
  [<ffffffff810ce186>] pwq_dec_nr_in_flight+0x66/0xa0
  [<ffffffff810ce490>] process_one_work+0x2d0/0x680
  [<ffffffff810ce331>] ? process_one_work+0x171/0x680
  [<ffffffff810ce88e>] worker_thread+0x4e/0x480
  [<ffffffff810ce840>] ? process_one_work+0x680/0x680
  [<ffffffff810ce840>] ? process_one_work+0x680/0x680
  [<ffffffff810d5343>] kthread+0xf3/0x110
  [<ffffffff8199846f>] ret_from_fork+0x1f/0x40
  [<ffffffff810d5250>] ? kthread_create_on_node+0x230/0x230

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uprobes/x86: Fix RIP-relative handling of EVEX-encoded instructions

commit 68187872c76a96ed4db7bfb064272591f02e208b upstream.

Since instruction decoder now supports EVEX-encoded instructions, two fixes
are needed to correctly handle them in uprobes.

Extended bits for MODRM.rm field need to be sanitized just like we do it
for VEX3, to avoid encoding wrong register for register-relative access.

EVEX has _two_ extended bits: b and x. Theoretically, EVEX.x should be
ignored by the CPU (since GPRs go only up to 15, not 31), but let's be
paranoid here: proper encoding for register-relative access
should have EVEX.x = 1.

Secondly, we should fetch vex.vvvv for EVEX too.
This is now super easy because instruction decoder populates
vex_prefix.bytes[2] for all flavors of (e)vex encodings, even for VEX2.

Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Fixes: 8a764a875fe3 ("x86/asm/decoder: Create artificial 3rd byte for 2-byte VEX")
Link: http://lkml.kernel.org/r/20160811154521.20469-1-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: Disable preemption during CR3 read+write

commit 5cf0791da5c162ebc14b01eb01631cfa7ed4fa6e upstream.

There's a subtle preemption race on UP kernels:

Usually current->mm (and therefore mm->pgd) stays the same during the
lifetime of a task so it does not matter if a task gets preempted during
the read and write of the CR3.

But then, there is this scenario on x86-UP:

TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by:

 -> mmput()
 -> exit_mmap()
 -> tlb_finish_mmu()
 -> tlb_flush_mmu()
 -> tlb_flush_mmu_tlbonly()
 -> tlb_flush()
 -> flush_tlb_mm_range()
 -> __flush_tlb_up()
 -> __flush_tlb()
 ->  __native_flush_tlb()

At this point current->mm is NULL but current->active_mm still points to
the "old" mm.

Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its
own mm so CR3 has changed.

Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's
mm and so CR3 remains unchanged. Once taskA gets active it continues
where it was interrupted and that means it writes its old CR3 value
back. Everything is fine because userland won't need its memory
anymore.

Now the fun part:

Let's preempt taskA one more time and get back to taskB. This
time switch_mm() won't do a thing because oldmm (->active_mm)
is the same as mm (as per context_switch()). So we remain
with a bad CR3 / PGD and return to userland.

The next thing that happens is handle_mm_fault() with an address for
the execution of its code in userland. handle_mm_fault() realizes that
it has a PTE with proper rights so it returns doing nothing. But the
CPU looks at the wrong PGD and insists that something is wrong and
faults again. And again. And one more time…

This pagefault circle continues until the scheduler gets tired of it and
puts another task on the CPU. It gets little difficult if the task is a
RT task with a high priority. The system will either freeze or it gets
fixed by the software watchdog thread which usually runs at RT-max prio.
But waiting for the watchdog will increase the latency of the RT task
which is no good.

Fix this by disabling preemption across the critical code section.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de
[ Prettified the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hugetlb: fix nr_pmds accounting with shared page tables

commit c17b1f42594eb71b8d3eb5a6dfc907a7eb88a51d upstream.

We account HugeTLB's shared page table to all processes who share it.
The accounting happens during huge_pmd_share().

If somebody populates pud entry under us, we should decrease pagetable's
refcount and decrease nr_pmds of the process.

By mistake, I increase nr_pmds again in this case.  :-/ It will lead to
"BUG: non-zero nr_pmds on freeing mm: 2" on process' exit.

Let's fix this by increasing nr_pmds only when we're sure that the page
table will be used.

Link: http://lkml.kernel.org/r/20160617122506.GC6534@node.shutemov.name
Fixes: dc6c9a35b66b ("mm: account pmd page tables to the process")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: zhongjiang <zhongjiang@huawei.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.19

Documentation/module-signing.txt: Note need for version info if reusing a key

commit b8612e517c3c9809e1200b72c474dbfd969e5a83 upstream.

Signing a module should only make it trusted by the specific kernel it
was built for, not anything else.  If a module signing key is used for
multiple ABI-incompatible kernels, the modules need to include enough
version information to distinguish them.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

module: Invalidate signatures on force-loaded modules

commit bca014caaa6130e57f69b5bf527967aa8ee70fdd upstream.

Signing a module should only make it trusted by the specific kernel it
was built for, not anything else.  Loading a signed module meant for a
kernel with a different ABI could have interesting effects.
Therefore, treat all signatures as invalid when a module is
force-loaded.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm flakey: error READ bios during the down_interval

commit 99f3c90d0d85708e7401a81ce3314e50bf7f2819 upstream.

When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval.  This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.

Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.

Fixes: a3998799fb4df ("dm flakey: add corrupt_bio_byte feature")
Reported-by: Akira Hayakawa <ruby.wktk@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()

commit 70c96dfac0e231424e17743bd52f6cd2ff1f2439 upstream.

As per code flow s3c_rtc_setfreq() will get called with rtc clock disabled
and in set_freq we perform h/w registers read/write, which results in a
kernel crash on exynos7 platform while probing rtc driver.
Below is code flow:
s3c_rtc_probe()
    clk_prepare_enable(info->rtc_clk) // rtc clock enabled
    s3c_rtc_gettime() // will enable clk if not done, and disable it upon exit
    s3c_rtc_setfreq() //then this will be called with clk disabled

This patch take cares of such issue by adding s3c_rtc_{enable/disable}_clk in
s3c_rtc_setfreq().

Fixes: 24e1455493da ("drivers/rtc/rtc-s3c.c: delete duplicate clock control")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lpfc: fix oops in lpfc_sli4_scmd_to_wqidx_distr() from lpfc_send_taskmgmt()

commit 05a05872c8d4b4357c9d913e6d73ae64882bddf5 upstream.

The lpfc_sli4_scmd_to_wqidx_distr() function expects the scsi_cmnd
'lpfc_cmd->pCmd' not to be null, and point to the midlayer command.

That's not true in the .eh_(device|target|bus)_reset_handler path,
because lpfc_send_taskmgmt() sends commands not from the midlayer, so
does not set 'lpfc_cmd->pCmd'.

That is true in the .queuecommand path because lpfc_queuecommand()
stores the scsi_cmnd from midlayer in lpfc_cmd->pCmd; and lpfc_cmd is
stored by lpfc_scsi_prep_cmnd() in piocbq->context1 -- which is passed
to lpfc_sli4_scmd_to_wqidx_distr() as lpfc_cmd parameter.

This problem can be hit on SCSI EH, and immediately with sg_reset.
These 2 test-cases demonstrate the problem/fix with next-20160601.

Test-case 1) sg_reset

    # strace sg_reset --device /dev/sdm
    <...>
    open("/dev/sdm", O_RDWR|O_NONBLOCK)     = 3
    ioctl(3, SG_SCSI_RESET, 0x3fffde6d0994 <unfinished ...>
    +++ killed by SIGSEGV +++
    Segmentation fault

    # dmesg
    Unable to handle kernel paging request for data at address 0x00000000
    Faulting instruction address: 0xd00000001c88442c
    Oops: Kernel access of bad area, sig: 11 [#1]
    <...>
    CPU: 104 PID: 16333 Comm: sg_reset Tainted: G        W       4.7.0-rc1-next-20160601-00004-g95b89dc #6
    <...>
    NIP [d00000001c88442c] lpfc_sli4_scmd_to_wqidx_distr+0xc/0xd0 [lpfc]
    LR [d00000001c826fe8] lpfc_sli_calc_ring.part.27+0x98/0xd0 [lpfc]
    Call Trace:
    [c000003c9ec876f0] [c000003c9ec87770] 0xc000003c9ec87770 (unreliable)
    [c000003c9ec87720] [d00000001c82e004] lpfc_sli_issue_iocb+0xd4/0x260 [lpfc]
    [c000003c9ec87780] [d00000001c831a3c] lpfc_sli_issue_iocb_wait+0x15c/0x5b0 [lpfc]
    [c000003c9ec87880] [d00000001c87f27c] lpfc_send_taskmgmt+0x24c/0x650 [lpfc]
    [c000003c9ec87950] [d00000001c87fd7c] lpfc_device_reset_handler+0x10c/0x200 [lpfc]
    [c000003c9ec87a10] [c000000000610694] scsi_try_bus_device_reset+0x44/0xc0
    [c000003c9ec87a40] [c0000000006113e8] scsi_ioctl_reset+0x198/0x2c0
    [c000003c9ec87bf0] [c00000000060fe5c] scsi_ioctl+0x13c/0x4b0
    [c000003c9ec87c80] [c0000000006629b0] sd_ioctl+0xf0/0x120
    [c000003c9ec87cd0] [c00000000046e4f8] blkdev_ioctl+0x248/0xb70
    [c000003c9ec87d30] [c0000000002a1f60] block_ioctl+0x70/0x90
    [c000003c9ec87d50] [c00000000026d334] do_vfs_ioctl+0xc4/0x890
    [c000003c9ec87de0] [c00000000026db60] SyS_ioctl+0x60/0xc0
    [c000003c9ec87e30] [c000000000009120] system_call+0x38/0x108
    Instruction dump:
    <...>

    With fix:

    # strace sg_reset --device /dev/sdm
    <...>
    open("/dev/sdm", O_RDWR|O_NONBLOCK)     = 3
    ioctl(3, SG_SCSI_RESET, 0x3fffe103c554) = 0
    close(3)                                = 0
    exit_group(0)                           = ?
    +++ exited with 0 +++

    # dmesg
    [  424.658649] lpfc 0006:01:00.4: 4:(0):0713 SCSI layer issued Device Reset (1, 0) return x2002

Test-case 2) SCSI EH

    Using this debug patch to wire an SCSI EH trigger, for lpfc_scsi_cmd_iocb_cmpl():
    -       cmd->scsi_done(cmd);
    +       if ((phba->pport ? phba->pport->cfg_log_verbose : phba->cfg_log_verbose) == 0x32100000)
    +               printk(KERN_ALERT "lpfc: skip scsi_done()\n");
    +       else
    +               cmd->scsi_done(cmd);

    # echo 0x32100000 > /sys/class/scsi_host/host11/lpfc_log_verbose

    # dd if=/dev/sdm of=/dev/null iflag=direct &
    <...>

    After a while:

    # dmesg
    lpfc 0006:01:00.4: 4:(0):3053 lpfc_log_verbose changed from 0 (x0) to 839909376 (x32100000)
    lpfc: skip scsi_done()
    <...>
    Unable to handle kernel paging request for data at address 0x00000000
    Faulting instruction address: 0xd0000000199e448c
    Oops: Kernel access of bad area, sig: 11 [#1]
    <...>
    CPU: 96 PID: 28556 Comm: scsi_eh_11 Tainted: G        W       4.7.0-rc1-next-20160601-00004-g95b89dc #6
    <...>
    NIP [d0000000199e448c] lpfc_sli4_scmd_to_wqidx_distr+0xc/0xd0 [lpfc]
    LR [d000000019986fe8] lpfc_sli_calc_ring.part.27+0x98/0xd0 [lpfc]
    Call Trace:
    [c000000ff0d0b890] [c000000ff0d0b900] 0xc000000ff0d0b900 (unreliable)
    [c000000ff0d0b8c0] [d00000001998e004] lpfc_sli_issue_iocb+0xd4/0x260 [lpfc]
    [c000000ff0d0b920] [d000000019991a3c] lpfc_sli_issue_iocb_wait+0x15c/0x5b0 [lpfc]
    [c000000ff0d0ba20] [d0000000199df27c] lpfc_send_taskmgmt+0x24c/0x650 [lpfc]
    [c000000ff0d0baf0] [d0000000199dfd7c] lpfc_device_reset_handler+0x10c/0x200 [lpfc]
    [c000000ff0d0bbb0] [c000000000610694] scsi_try_bus_device_reset+0x44/0xc0
    [c000000ff0d0bbe0] [c0000000006126cc] scsi_eh_ready_devs+0x49c/0x9c0
    [c000000ff0d0bcb0] [c000000000614160] scsi_error_handler+0x580/0x680
    [c000000ff0d0bd80] [c0000000000ae848] kthread+0x108/0x130
    [c000000ff0d0be30] [c0000000000094a8] ret_from_kernel_thread+0x5c/0xb4
    Instruction dump:
    <...>

    With fix:

    # dmesg
    lpfc 0006:01:00.4: 4:(0):3053 lpfc_log_verbose changed from 0 (x0) to 839909376 (x32100000)
    lpfc: skip scsi_done()
    <...>
    lpfc 0006:01:00.4: 4:(0):0713 SCSI layer issued Device Reset (0, 0) return x2002
    <...>
    lpfc 0006:01:00.4: 4:(0):0723 SCSI layer issued Target Reset (1, 0) return x2002
    <...>
    lpfc 0006:01:00.4: 4:(0):0714 SCSI layer issued Bus Reset Data: x2002
    <...>
    lpfc 0006:01:00.4: 4:(0):3172 SCSI layer issued Host Reset Data:
    <...>

Fixes: 8b0dff14164d ("lpfc: Add support for using block multi-queue")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI / EC: Work around method reentrancy limit in ACPICA for _Qxx

commit e1191bd4f62d9086a1a47adc286e7fcffc1fa55c upstream.

A regression is caused by the following commit:

  Commit: 02b771b64b73226052d6e731a0987db3b47281e9
  Subject: ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations

In this commit, using system workqueue causes that the maximum parallel
executions of _Qxx can exceed 255. This violates the method reentrancy
limit in ACPICA and generates the following error log:

  ACPI Error: Method reached maximum reentrancy limit (255) (20150818/dsmethod-341)

This patch creates a seperate workqueue and limits the number of parallel
_Qxx evaluations down to a configurable value (can be tuned against number
of online CPUs).

Since EC events are handled after driver probe, we can create the workqueue
in acpi_ec_init().

Fixes: 02b771b64b73 (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=135691
Reported-and-tested-by: Helen Buus <ubuntu@hbuus.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/platform/intel_mid_pci: Rework IRQ0 workaround

commit bb27570525a71f48347ed0e0c265063e7952bb61 upstream.

On Intel Merrifield platform several PCI devices have a bogus configuration,
i.e. the IRQ0 had been assigned to few of them. These are PCI root bridge,
eMMC0, HS UART common registers, PWM, and HDMI. The actual interrupt line can
be allocated to one device exclusively, in our case to eMMC0, the rest should
cope without it and basically known drivers for them are not using interrupt
line at all.

Rework IRQ0 workaround, which was previously done to avoid conflict between
eMMC0 and HS UART common registers, to behave differently based on the device
in question, i.e. allocate interrupt line to eMMC0, but silently skip interrupt
allocation for the rest except HS UART common registers which are not used
anyway. With this rework IOSF MBI driver in particular would be used.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 39d9b77b8deb ("x86/pci/intel_mid_pci: Work around for IRQ0 assignment")
Link: http://lkml.kernel.org/r/1465842481-136852-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset

commit 9ac0108c2bac3f1d0255f64fb89fc27e71131b24 upstream.

Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have
the same quirk for the Bus Reset.

Fixes: c3e59ee4e766 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: hpet: Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES

commit 3ef06653987d4c4536b408321edf0e5caa2a317f upstream.

At first, we prefer to use mips clockevent device, so we decrease the
rating of hpet clockevent device.

For hpet, if HPET_MIN_PROG_DELTA (minimum delta of hpet programming) is
too small and HPET_MIN_CYCLES (threshold of -ETIME checking) is too
large, then hpet_next_event() can easily return -ETIME. After commit
c6eb3f70d44828 ("hrtimer: Get rid of hrtimer softirq") this will cause
a RCU stall.

So, HPET_MIN_PROG_DELTA must be sufficient that we don't re-trip the
-ETIME check -- if we do, we will return -ETIME, forward the next event
time, try to set it, return -ETIME again, and basically lock the system
up. Meanwhile, HPET_MIN_CYCLES doesn't need to be too large, 16 cycles
is enough.

This solution is similar to commit f9eccf24615672 ("clocksource/drivers
/vt8500: Increase the minimum delta").

By the way, this patch ensures hpet count/compare to be 32-bit long.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Don't register r4k sched clock when CPUFREQ enabled

commit 07d69579e7fec27e371296d8ca9d6076fc401b5c upstream.

Don't register r4k sched clock when CPUFREQ enabled because sched clock
need a constant frequency.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13820/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: mm: Fix definition of R6 cache instruction

commit 4f53989b0652ffe2605221c81ca8ffcfc90aed2a upstream.

Commit a168b8f1cde6 ("MIPS: mm: Add MIPS R6 instruction encodings") added
an incorrect definition of the redefined MIPSr6 cache instruction.

Executing any kernel code including this instuction results in a
reserved instruction exception and kernel panic.

Fix the instruction definition.

Fixes: a168b8f1cde6588ff7a67699fa11e01bc77a5ddd
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13663/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SUNRPC: Don't allocate a full sockaddr_storage for tracing

commit db1bb44c4c7e8d49ed674dc59e5222d99c698088 upstream.

We're always tracing IPv4 or IPv6 addresses, so we can save a lot
of space on the ringbuffer by allocating the correct sockaddr size.

Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fixes: 83a712e0afef "sunrpc: add some tracepoints around ..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elan_i2c - properly wake up touchpad on ASUS laptops

commit 2de4fcc64685def3e586856a2dc636df44532395 upstream.

Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:

elan_i2c i2c-ELAN1000:00: invalid report id data (1)

Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Vlad Glagolev <stealth@vaygr.net>
Tested-by: Vlad Glagolev <stealth@vaygr.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix ordered task CHECK_CONDITION early exception handling

commit 410c29dfbfdf73d0d0b5d14a21868ab038eca703 upstream.

If a Simple command is sent with a failure, target_setup_cmd_from_cdb
returns with TCM_UNSUPPORTED_SCSI_OPCODE or TCM_INVALID_CDB_FIELD.

So in the cases where target_setup_cmd_from_cdb returns an error, we
never get far enough to call target_execute_cmd to increment simple_cmds.
Since simple_cmds isn't incremented, the result of the failure from
target_setup_cmd_from_cdb causes transport_generic_request_failure to
decrement simple_cmds, due to call to transport_complete_task_attr.

With this dev->simple_cmds or dev->dev_ordered_sync is now -1, not 0.
So when a subsequent command with an Ordered Task is sent, it causes
a hang, since dev->simple_cmds is at -1.

Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix max_unmap_lba_count calc overflow

commit ea263c7fada4af8ec7fe5fcfd6e7d7705a89351b upstream.

max_discard_sectors only 32bits, and some non scsi backend
devices will set this to the max 0xffffffff, so we can end up
overflowing during the max_unmap_lba_count calculation.

This fixes a regression caused by my patch:

commit 8a9ebe717a133ba7bc90b06047f43cc6b8bcb8b3
Author: Mike Christie <mchristi@redhat.com>
Date:   Mon Jan 18 14:09:27 2016 -0600

    target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors

which can result in extra discards being sent to due the overflow
causing max_unmap_lba_count to be smaller than what the backing
device can actually support.

Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix race between iscsi-target connection shutdown + ABORT_TASK

commit 064cdd2d91c2805d788876082f31cc63506f22c3 upstream.

This patch fixes a race in iscsit_release_commands_from_conn() ->
iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1,
where CMD_T_FABRIC_STOP could end up being set after the final
kref_put() is called from core_tmr_abort_task() context.

This results in transport_generic_free_cmd() blocking indefinately
on se_cmd->cmd_wait_comp, because the target_release_cmd_kref()
check for CMD_T_FABRIC_STOP returns false.

To address this bug, make iscsit_release_commands_from_conn()
do list_splice and set CMD_T_FABRIC_STOP early while holding
iscsi_conn->cmd_lock.  Also make iscsit_aborted_task() only
remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been
set.

Finally in target_release_cmd_kref(), only honor fabric_stop
if CMD_T_ABORTED has been set.

Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix missing complete during ABORT_TASK + CMD_T_FABRIC_STOP

commit 5e2c956b8aa24d4f33ff7afef92d409eed164746 upstream.

During transport_generic_free_cmd() with a concurrent TMR
ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the
caller will be blocked on se_cmd->cmd_wait_stop completion
until the final kref_put() -> target_release_cmd_kref()
has been invoked to call complete().

However, when ABORT_TASK is completed with FUNCTION_COMPLETE
in core_tmr_abort_task(), the aborted se_cmd will have already
been removed from se_sess->sess_cmd_list via list_del_init().

This results in target_release_cmd_kref() hitting the
legacy list_empty() == true check, invoking ->release_cmd()
but skipping complete() to wakeup se_cmd->cmd_wait_stop
blocked earlier in transport_generic_free_cmd() code.

To address this bug, it's safe to go ahead and drop the
original list_empty() check so that fabric_stop invokes
the complete() as expected, since list_del_init() can
safely be used on a empty list.

Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix ordered task target_setup_cmd_from_cdb exception hang

commit dff0ca9ea7dc8be2181a62df4a722c32ce68ff4a upstream.

If a command with a Simple task attribute is failed due to a Unit
Attention, then a subsequent command with an Ordered task attribute
will hang forever.  The reason for this is that the Unit Attention
status is checked for in target_setup_cmd_from_cdb, before the call
to target_execute_cmd, which calls target_handle_task_attr, which
in turn increments dev->simple_cmds.

However, transport_generic_request_failure still calls
transport_complete_task_attr, which will decrement dev->simple_cmds.
In this case, simple_cmds is now -1.  So when a command with the
Ordered task attribute is sent, target_handle_task_attr sees that
dev->simple_cmds is not 0, so it decides it can't execute the
command until all the (nonexistent) Simple commands have completed.

Reported-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iscsi-target: Fix panic when adding second TCP connection to iSCSI session

commit 8abc718de6e9e52d8a6bfdb735060554aeae25e4 upstream.

In MC/S scenario, the conn->sess has been set NULL in
iscsi_login_non_zero_tsih_s1 when the second connection comes here,
then kernel panic.

The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So
we should check whether it's NULL before calling.

Signed-off-by: Feng Li <lifeng1519@gmail.com>
Tested-by: Sumit Rai <sumit.rai@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ubi: Fix race condition between ubi device creation and udev

commit 714fb87e8bc05ff78255afc0dca981e8c5242785 upstream.

Install the UBI device object before we arm sysfs.
Otherwise udev tries to read sysfs attributes before UBI is ready and
udev rules will not match.

Signed-off-by: Iosif Harutyunov <iharutyunov@sonicwall.com>
[rw: massaged commit message]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ubi: Fix early logging

commit bc743f34dfa011e62edd0ea4ae8455be06c083b5 upstream.

We cannot use ubi_* logging functions before the UBI
object is initialized.

Fixes: 3260870331 ("UBI: Extend UBI layer debug/messaging capabilities")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ubi: Make volume resize power cut aware

commit 4946784bd3924b1374f05eebff2fd68660bae866 upstream.

When the volume resize operation shrinks a volume,
LEBs will be unmapped. Since unmapping will not erase these
LEBs immediately we have to wait for that operation to finish.
Otherwise in case of a power cut right after writing the new
volume table the UBI attach process can find more LEBs than the
volume table knows. This will render the UBI image unattachable.

Fix this issue by waiting for erase to complete and write the new
volume table afterward.

Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of: fix memory leak related to safe_name()

commit d9fc880723321dbf16b2981e3f3e916b73942210 upstream.

Fix a memory leak resulting from memory allocation in safe_name().
This patch fixes all call sites of safe_name().

Mathieu Malaterre reported the memory leak on boot:

On my PowerMac device-tree would generate a duplicate name:

[    0.023043] device-tree: Duplicate name in PowerPC,G4@0, renamed to "l2-cache#1"

in this case a newly allocated name is generated by `safe_name`. However
in this case it is never deallocated.

The bug was found using kmemleak reported as:

unreferenced object 0xdf532e60 (size 32):
  comm "swapper", pid 1, jiffies 4294892300 (age 1993.532s)
  hex dump (first 32 bytes):
    6c 32 2d 63 61 63 68 65 23 31 00 dd e4 dd 1e c2  l2-cache#1......
    ec d4 ba ce 04 ec cc de 8e 85 e9 ca c4 ec cc 9e  ................
  backtrace:
    [<c02d3350>] kvasprintf+0x64/0xc8
    [<c02d3400>] kasprintf+0x4c/0x5c
    [<c0453814>] safe_name.isra.1+0x80/0xc4
    [<c04545d8>] __of_attach_node_sysfs+0x6c/0x11c
    [<c075f21c>] of_core_init+0x8c/0xf8
    [<c0729594>] kernel_init_freeable+0xd4/0x208
    [<c00047e8>] kernel_init+0x24/0x11c
    [<c00158ec>] ret_from_kernel_thread+0x5c/0x64

Link: https://bugzilla.kernel.org/show_bug.cgi?id=120331
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Reported-by: mathieu.malaterre@gmail.com
Tested-by: Mathieu Malaterre <mathieu.malaterre@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix memory leak if QP creation failed

commit 5b420d9cf7382c6e1512e96e02d18842d272049c upstream.

When RC, UC, or RAW QPs are created, a qp object is allocated (kzalloc).
If at a later point (in procedure create_qp_common) the qp creation fails,
this qp object must be freed.

Fixes: 1ffeb2eb8be99 ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix error flow when sending mads under SRIOV

commit a6100603a4a87fc436199362bdb81cb849faaf6e upstream.

Fix mad send error flow to prevent double freeing address handles,
and leaking tx_ring entries when SRIOV is active.

If ib_mad_post_send fails, the address handle pointer in the tx_ring entry
must be set to NULL (or there will be a double-free) and tx_tail must be
incremented (or there will be a leak of tx_ring entries).
The tx_ring is handled the same way in the send-completion handler.

Fixes: 37bfc7c1e83f ("IB/mlx4: SR-IOV multiplex and demultiplex MADs")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix the SQ size of an RC QP

commit f2940e2c76bb554a7fbdd28ca5b90904117a9e96 upstream.

When calculating the required size of an RC QP send queue, leave
enough space for masked atomic operations, which require more space than
"regular" atomic operation.

Fixes: 6fa8f719844b ("IB/mlx4: Add support for masked atomic operations")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@mellanox.co.il>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/IWPM: Fix a potential skb leak

commit 5ed935e861a4cbf2158ad3386d6d26edd60d2658 upstream.

In case ibnl_put_msg fails in send_nlmsg_done,
the function returns with -ENOMEM without freeing.

This patch fixes this behavior.

Fixes: 30dc5e63d6a5 ("RDMA/core: Add support for iWARP Port Mapper user space service")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/IPoIB: Don't update neigh validity for unresolved entries

commit 61c78eea9516a921799c17b4c20558e2aa780fd3 upstream.

ipoib_neigh_get unconditionally updates the "alive" variable member on
any packet send.  This prevents the neighbor garbage collection from
cleaning out a dead neighbor entry if we are still queueing packets
for it.  If the queue for this neighbor is full, then don't update the
alive timestamp.  That way the neighbor can time out even if packets
are still being queued as long as none of them are being sent.

Fixes: b63b70d87741 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/SA: Use correct free function

commit 0f377d86252d11bfea941852785e3094b93601a7 upstream.

Fixes a direct call to kfree_skb when nlmsg_free should be used.

Fixes: 2ca546b92a02 ('IB/sa: Route SA pathrecord query through netlink')
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Return PORT_ERR in Active to Initializing tranisition

commit 2788cf3bd90af3791c3195c52391bcf34fa67b40 upstream.

FW port-change events are fired on Active <-> non Active port state
transitions only.
When the port state changes from Active to Initializing (Active ->
Down -> Initializing), a single event is fired.
The HCA transitions from Down to Initializing unless prevented from
doing so, hence the driver should also propagate events when the port
state is Initializing to consumers so they'll be aware that the port
is no longer Active and act accordingly.

Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix post send fence logic

commit c9b254955b9f8814966f5dabd34c39d0e0a2b437 upstream.

If the caller specified IB_SEND_FENCE in the send flags of the work
request and no previous work request stated that the successive one
should be fenced, the work request would be executed without a fence.
This could result in RDMA read or atomic operations failure due to a MR
being invalidated. Fix this by adding the mlx5 enumeration for fencing
RDMA/atomic operations and fix the logic to apply this.

Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix entries check in mlx5_ib_resize_cq

commit 3c4c37746c919c983e439ac6a7328cd2d48c10ed upstream.

Verify that number of entries is less than device capability.
Add an appropriate warning message for error flow.

Fixes: bde51583f49b ('IB/mlx5: Add support for resize CQ')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix returned values of query QP

commit 0540d8148d419bf769e5aa99c77027febd8922f0 upstream.

Some variables were not initialized properly: max_recv_wr,
max_recv_sge, max_send_wr, qp_context and max_inline_data.

Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix entries checks in mlx5_ib_create_cq

commit 9ea578528656e191c1097798a771ff08bab6f323 upstream.

Number of entries shouldn't be greater than the device's max
capability. This should be checked before rounding the entries number
to power of two.

Fixes: 51ee86a4af639 ('IB/mlx5: Fix check of number of entries...')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix MODIFY_QP command input structure

commit e3353c268b06236d6c40fa1714c114f21f44451c upstream.

Make MODIFY_QP command input structure compliant to specification

Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Fix headset mic detection problem for two dell machines

commit 59ec4b57bcaede46546d54d037a21004b9aa5cef upstream.

One of the machines has ALC255 on it, another one has ALC298 on it.

On the machine with the codec ALC298, it also has the speaker volume
problem, so we add the fixup chained to ALC298_FIXUP_SPK_VOLUME rather
than adding a group of pin definition in the pin quirk table, since
the speak volume problem does not happen on other machines yet.

Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: add AMD Bonaire AZ PCI ID with proper driver caps

commit fd48331f9b71d2add941adaee3619f5b8527182d upstream.

This commit fixes garbled audio on Bonaire HDMI

Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Can't adjust speaker's volume on a Dell AIO

commit dd9aa335c88003d131ac874e7f6809902de0b847 upstream.

We have a Dell AIO on which we can't adjust its speaker's volume.
The problem is it is connected to a Audio Output node without Amp-out
capability. To fix it, we change it to be connnected to a node with
Amp-out capability.

Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Fix krealloc() with __GFP_ZERO usage

commit 33baefe5e72f17a6df378e48196cd8cada11deec upstream.

krealloc() doesn't work always properly with __GFP_ZERO flag as
expected.  For clearing the reallocated area, we need to clear
explicitly instead.

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/hugetlb: avoid soft lockup in set_max_huge_pages()

commit 649920c6ab93429b94bc7c1aa7c0e8395351be32 upstream.

In powerpc servers with large memory(32TB), we watched several soft
lockups for hugepage under stress tests.

The call traces are as follows:
1.
get_page_from_freelist+0x2d8/0xd50
__alloc_pages_nodemask+0x180/0xc20
alloc_fresh_huge_page+0xb0/0x190
set_max_huge_pages+0x164/0x3b0

2.
prep_new_huge_page+0x5c/0x100
alloc_fresh_huge_page+0xc8/0x190
set_max_huge_pages+0x164/0x3b0

This patch fixes such soft lockups.  It is safe to call cond_resched()
there because it is out of spin_lock/unlock section.

Link: http://lkml.kernel.org/r/1469674442-14848-1-git-send-email-hejianet@gmail.com
Signed-off-by: Jia He <hejianet@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: nand: fix bug writing 1 byte less than page size

commit 144f4c98399e2c0ca60eb414c15a2c68125c18b8 upstream.

nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))

When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.

The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff

[Editor's note: the bug was added in commit 29072b96078f, but moved
around in commit 66507c7bc8895 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]

Fixes: 29072b96078f ("[MTD] NAND: add subpage write support")
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: fix bdi vs gendisk lifetime mismatch

commit df08c32ce3be5be138c1dbfcba203314a3a7cd6f upstream.

The name for a bdi of a gendisk is derived from the gendisk's devt.
However, since the gendisk is destroyed before the bdi it leaves a
window where a new gendisk could dynamically reuse the same devt while a
bdi with the same name is still live.  Arrange for the bdi to hold a
reference against its "owner" disk device while it is registered.
Otherwise we can hit sysfs duplicate name collisions like the following:

 WARNING: CPU: 10 PID: 2078 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x64/0x80
 sysfs: cannot create duplicate filename '/devices/virtual/bdi/259:1'

 Hardware name: HP ProLiant DL580 Gen8, BIOS P79 05/06/2015
  0000000000000286 0000000002c04ad5 ffff88006f24f970 ffffffff8134caec
  ffff88006f24f9c0 0000000000000000 ffff88006f24f9b0 ffffffff8108c351
  0000001f0000000c ffff88105d236000 ffff88105d1031e0 ffff8800357427f8
 Call Trace:
  [<ffffffff8134caec>] dump_stack+0x63/0x87
  [<ffffffff8108c351>] __warn+0xd1/0xf0
  [<ffffffff8108c3cf>] warn_slowpath_fmt+0x5f/0x80
  [<ffffffff812a0d34>] sysfs_warn_dup+0x64/0x80
  [<ffffffff812a0e1e>] sysfs_create_dir_ns+0x7e/0x90
  [<ffffffff8134faaa>] kobject_add_internal+0xaa/0x320
  [<ffffffff81358d4e>] ? vsnprintf+0x34e/0x4d0
  [<ffffffff8134ff55>] kobject_add+0x75/0xd0
  [<ffffffff816e66b2>] ? mutex_lock+0x12/0x2f
  [<ffffffff8148b0a5>] device_add+0x125/0x610
  [<ffffffff8148b788>] device_create_groups_vargs+0xd8/0x100
  [<ffffffff8148b7cc>] device_create_vargs+0x1c/0x20
  [<ffffffff811b775c>] bdi_register+0x8c/0x180
  [<ffffffff811b7877>] bdi_register_dev+0x27/0x30
  [<ffffffff813317f5>] add_disk+0x175/0x4a0

Reported-by: Yi Zhang <yizhan@redhat.com>
Tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed up missing 0 return in bdi_register_owner().

Signed-off-by: Jens Axboe <axboe@fb.com>

block: add missing group association in bio-cloning functions

commit 20bd723ec6a3261df5e02250cd3a1fbb09a343f2 upstream.

When a bio is cloned, the newly created bio must be associated with
the same blkcg as the original bio (if BLK_CGROUP is enabled). If
this operation is not performed, then the new bio is not associated
with any group, and the group of the current task is returned when
the group of the bio is requested.

Depending on the cloning frequency, this may cause a large
percentage of the bios belonging to a given group to be treated
as if belonging to other groups (in most cases as if belonging to
the root group). The expected group isolation may thereby be broken.

This commit adds the missing association in bio-cloning functions.

Fixes: da2f0f74cf7d ("Btrfs: add support for blkio controllers")
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Nikolay Borisov <kernel@kyup.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

metag: Fix __cmpxchg_u32 asm constraint for CMP

commit 6154c187b97ee7513046bb4eb317a89f738f13ef upstream.

The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect
constraints for the return value which under certain circumstances can
allow an address unit register to be used as the first operand of a CMP
instruction. This isn't a valid instruction however as the encodings
only allow a data unit to be specified. This would result in an
assembler error like the following:

  Error: failed to assemble instruction: "CMP A0.2,D0Ar6"

Fix by changing the constraint from "=&da" (assigned, early clobbered,
data or address unit register) to "=&d" (data unit register only).

The constraint for the second operand, "bd" (an op2 register where op1
is a data unit register and the instruction supports O2R) is already
correct assuming the first operand is a data unit register.

Other cases of CMP in inline asm have had their constraints checked, and
appear to all be fine.

Fixes: 6006c0d8ce94 ("metag: Atomics, locks and bitops")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ftrace/recordmcount: Work around for addition of metag magic but not relocations

commit b2e1c26f0b62531636509fbcb6dab65617ed8331 upstream.

glibc recently did a sync up (94e73c95d9b5 "elf.h: Sync with the gabi
webpage") that added a #define for EM_METAG but did not add relocations

This triggers build errors:

scripts/recordmcount.c: In function 'do_file':
scripts/recordmcount.c:466:28: error: 'R_METAG_ADDR32' undeclared (first use in this function)
  case EM_METAG:  reltype = R_METAG_ADDR32;
                            ^~~~~~~~~~~~~~
scripts/recordmcount.c:466:28: note: each undeclared identifier is reported only once for each function it appears in
scripts/recordmcount.c:468:20: error: 'R_METAG_NONE' undeclared (first use in this function)
     rel_type_nop = R_METAG_NONE;
                    ^~~~~~~~~~~~

Work around this change with some more #ifdefery for the relocations.

Fedora Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1354034

Link: http://lkml.kernel.org/r/1468005530-14757-1-git-send-email-labbott@redhat.com
Cc: James Hogan <james.hogan@imgtec.com>
Fixes: 00512bdd4573 ("metag: ftrace support")
Reported-by: Ross Burton <ross.burton@intel.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

balloon: check the number of available pages in leak balloon

commit 37cf99e08c6fb4dcea0f9ad2b13b6daa8c76a711 upstream.

The balloon has a special mechanism that is subscribed to the oom
notification which leads to deflation for a fixed number of pages.
The number is always fixed even when the balloon is fully deflated.
But leak_balloon did not expect that the pages to deflate will be more
than taken, and raise a "BUG" in balloon_page_dequeue when page list
will be empty.

So, the simplest solution would be to check that the number of releases
pages is less or equal to the number taken pages.

Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"

commit 196f954e250943df414efd3d632254c29be38e59 upstream.

This reverts commit 013dd9e03872
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown")

This commit introduced a regression into stable kernels,
as it reduces output color depth to 6 bpc for any video
sink connected to a Displayport connector if that sink
doesn't report a specific color depth via EDID, or if
our EDID parser doesn't actually recognize the proper
bpc from EDID.

Affected are active DisplayPort->VGA converters and
active DisplayPort->DVI converters. Both should be
able to handle 8 bpc, but are degraded to 6 bpc with
this patch.

The reverted commit was meant to fix
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331

A followup patch implements a fix for that specific bug,
which is caused by a faulty EDID of the affected DP panel
by adding a new EDID quirk for that panel.

DP 18 bpp fallback handling and other improvements to
DP sink bpc detection will be handled for future
kernels in a separate series of patches.

Please backport to stable.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB

commit a7b4667a00025ac28300737c868bd4818b6d8c4d upstream.

SNB (and IVB too I suppose) starts to misbehave if the GPU gets stuck
in an infinite batch buffer loop. The GPU apparently hogs something
critical and CPUs start to lose interrupts and whatnot. We can keep
the system limping along by unmasking some interrupts in
GEN6_PMINTRMSK. The EI up interrupt has been previously chosen for
that task, so let's never mask it.

v2: s/gen6_rps_pm_mask/gen6_sanitize_rps_pm_mask/ (Chris)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93122
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1464014568-4529-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 12c100bfa5d9103b6c4d43636fee09c31e75605a)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/edid: Add 6 bpc quirk for display AEO model 0.

commit e10aec652f31ec61d6a0b4d00d8ef8d2b66fa0fd upstream.

Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.

A fix for this was made by commit 013dd9e03872
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").

That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.

The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.

Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.

Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.

This patch should be backported to stable.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: Restore double clflush on the last partial cacheline

commit 396f5d62d1a5fd99421855a08ffdef8edb43c76e upstream.

This effectively reverts

commit afcd950cafea6e27b739fe7772cbbeed37d05b8b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Jun 10 15:58:01 2015 +0100

    drm: Avoid the double clflush on the last cache line in drm_clflush_virt_range()

as we have observed issues with serialisation of the clflush operations
on Baytrail+ Atoms with partial updates. Applying the double flush on the
last cacheline forces that clflush to be ordered with respect to the
previous clflush, and the mfence then protects against prefetches crossing
the clflush boundary.

The same issue can be demonstrated in userspace with igt/gem_exec_flush.

Fixes: afcd950cafea6 (drm: Avoid the double clflush on the last cache...)
Testcase: igt/gem_concurrent_blit
Testcase: igt/gem_partial_pread_pwrite
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92845
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jason Ekstrand <jason.ekstrand@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1467880930-23082-6-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/fbcon: fix font width not divisible by 8

commit 28668f43b8e421634e1623f72a879812288dd06b upstream.

The patch f045f459d925 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
tries to fix some out of memory accesses. Unfortunatelly, the patch breaks the
display when using fonts with width that is not divisiable by 8.

The monochrome bitmap for each character is stored in memory by lines from top
to bottom. Each line is padded to a full byte.

For example, for 22x11 font, each line is padded to 16 bits, so each
character is consuming 44 bytes total, that is 11 32-bit words. The patch
f045f459d925 changed the logic to "dsize = ALIGN(image->width *
image->height, 32) >> 5", that is just 8 words - this is incorrect and it
causes display corruption.

This patch adds the necesary padding of lines to 8 bytes.

This patch should be backported to stable kernels where f045f459d925 was
backported.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: f045f459d925 ("drm/nouveau/fbcon: fix out-of-bounds memory accesses")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup

commit d0e62ef6ed257715a88d0e5d7cd850a1695429e2 upstream.

This should fix some unaligned access warnings. This is also likely to
fix non-descript issues on nv30/nv34 as a result of incorrect channel
setup.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96836
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau: check for supported chipset before booting fbdev off the hw

commit 0e67bed2c765ff0fdaec62c963881f5416fe3692 upstream.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: support backlight control for UNIPHY3

commit d3200be6c423afa1c34f7e39e9f6d04dd5b0af9d upstream.

Same interface as other UNIPHY blocks

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: fix firmware info version checks

commit 3edc38a0facef45ee22af8afdce3737f421f36ab upstream.

Some of the checks didn't handle frev 2 tables properly.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: Poll for both connect/disconnect on analog connectors

commit 14ff8d48f2235295dfb3117693008e367b49cdb5 upstream.

DRM_CONNECTOR_POLL_CONNECT only enables polling for connections, not
disconnections. Because of this, we end up losing hotplug polling for
analog connectors once they get connected.

Easy way to reproduce:
 - Grab a machine with a radeon GPU and a VGA port
 - Plug a monitor into the VGA port, wait for it to update the connector
   from disconnected to connected
 - Disconnect the monitor on VGA, a hotplug event is never sent for the
   removal of the connector.

Originally, only using DRM_CONNECTOR_POLL_CONNECT might have been a good
idea since doing VGA polling can sometimes result in having to mess with
the DAC voltages to figure out whether or not there's actually something
there since VGA doesn't have HPD. Doing this would have the potential of
showing visible artifacts on the screen every time we ran a poll while a
VGA display was connected. Luckily, radeon_vga_detect() only resorts to
this sort of polling if the poll is forced, and DRM's polling helper
doesn't force it's polls.

Additionally, this removes some assignments to connector->polled that
weren't actually doing anything.

Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: add a delay after ATPX dGPU power off

commit d814b24fb74cb9797d70cb8053961447c5879a5c upstream.

ATPX dGPU power control requires a 200ms delay between
power off and on.  This should fix dGPU failures on
resume from power off.

Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu/gmc7: add missing mullins case

commit 7f555c8e5a84b348c2b76f4ca78eae7222354c03 upstream.

Looks like this got missed when we ported the code from radeon.

Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>