IB/qib: Fix port in pkey change event

commit 911eccd284d13d78c92ec4f1f1092c03457d732a upstream.

The code used a literal 1 in dispatching an IB_EVENT_PKEY_CHANGE.

As of the dual port qib QDR card, this is not necessarily correct.

Change to use the port as specified in the call.

Reported-by: Alex Estrin <alex.estrin@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: ath79_wdt: avoid spurious restarts on AR934x

commit 23afeb613ec0e10aecfae7838a14d485db62ac52 upstream.

On some AR934x based systems, where the frequency of
the AHB bus is relatively high, the built-in watchdog
causes a spurious restart when it gets enabled.

The possible cause of these restarts is that the timeout
value written into the TIMER register does not reaches
the hardware in time.

Add an explicit delay into the ath79_wdt_enable function
to avoid the spurious restarts.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: sp805: Set watchdog_device->timeout from ->set_timeout()

commit 938626d96a3ffb9eb54552bb0d3a4f2b30ffdeb0 upstream.

Implementation of ->set_timeout() is supposed to set 'timeout' field of 'struct
watchdog_device' passed to it. sp805 was rather setting this in a local
variable. Fix it.

Reported-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UBIFS: Remove incorrect assertion in shrink_tnc()

commit 72abc8f4b4e8574318189886de627a2bfe6cd0da upstream.

I hit the same assert failed as Dolev Raviv reported in Kernel v3.10
shows like this:

[ 9641.164028] UBIFS assert failed in shrink_tnc at 131 (pid 13297)
[ 9641.234078] CPU: 1 PID: 13297 Comm: mmap.test Tainted: G           O 3.10.40 #1
[ 9641.234116] [<c0011a6c>] (unwind_backtrace+0x0/0x12c) from [<c000d0b0>] (show_stack+0x20/0x24)
[ 9641.234137] [<c000d0b0>] (show_stack+0x20/0x24) from [<c0311134>] (dump_stack+0x20/0x28)
[ 9641.234188] [<c0311134>] (dump_stack+0x20/0x28) from [<bf22425c>] (shrink_tnc_trees+0x25c/0x350 [ubifs])
[ 9641.234265] [<bf22425c>] (shrink_tnc_trees+0x25c/0x350 [ubifs]) from [<bf2245ac>] (ubifs_shrinker+0x25c/0x310 [ubifs])
[ 9641.234307] [<bf2245ac>] (ubifs_shrinker+0x25c/0x310 [ubifs]) from [<c00cdad8>] (shrink_slab+0x1d4/0x2f8)
[ 9641.234327] [<c00cdad8>] (shrink_slab+0x1d4/0x2f8) from [<c00d03d0>] (do_try_to_free_pages+0x300/0x544)
[ 9641.234344] [<c00d03d0>] (do_try_to_free_pages+0x300/0x544) from [<c00d0a44>] (try_to_free_pages+0x2d0/0x398)
[ 9641.234363] [<c00d0a44>] (try_to_free_pages+0x2d0/0x398) from [<c00c6a60>] (__alloc_pages_nodemask+0x494/0x7e8)
[ 9641.234382] [<c00c6a60>] (__alloc_pages_nodemask+0x494/0x7e8) from [<c00f62d8>] (new_slab+0x78/0x238)
[ 9641.234400] [<c00f62d8>] (new_slab+0x78/0x238) from [<c031081c>] (__slab_alloc.constprop.42+0x1a4/0x50c)
[ 9641.234419] [<c031081c>] (__slab_alloc.constprop.42+0x1a4/0x50c) from [<c00f80e8>] (kmem_cache_alloc_trace+0x54/0x188)
[ 9641.234459] [<c00f80e8>] (kmem_cache_alloc_trace+0x54/0x188) from [<bf227908>] (do_readpage+0x168/0x468 [ubifs])
[ 9641.234553] [<bf227908>] (do_readpage+0x168/0x468 [ubifs]) from [<bf2296a0>] (ubifs_readpage+0x424/0x464 [ubifs])
[ 9641.234606] [<bf2296a0>] (ubifs_readpage+0x424/0x464 [ubifs]) from [<c00c17c0>] (filemap_fault+0x304/0x418)
[ 9641.234638] [<c00c17c0>] (filemap_fault+0x304/0x418) from [<c00de694>] (__do_fault+0xd4/0x530)
[ 9641.234665] [<c00de694>] (__do_fault+0xd4/0x530) from [<c00e10c0>] (handle_pte_fault+0x480/0xf54)
[ 9641.234690] [<c00e10c0>] (handle_pte_fault+0x480/0xf54) from [<c00e2bf8>] (handle_mm_fault+0x140/0x184)
[ 9641.234716] [<c00e2bf8>] (handle_mm_fault+0x140/0x184) from [<c0316688>] (do_page_fault+0x150/0x3ac)
[ 9641.234737] [<c0316688>] (do_page_fault+0x150/0x3ac) from [<c000842c>] (do_DataAbort+0x3c/0xa0)
[ 9641.234759] [<c000842c>] (do_DataAbort+0x3c/0xa0) from [<c0314e38>] (__dabt_usr+0x38/0x40)

After analyzing the code, I found a condition that may cause this failed
in correct operations. Thus, I think this assertion is wrong and should be
removed.

Suppose there are two clean znodes and one dirty znode in TNC. So the
per-filesystem atomic_t @clean_zn_cnt is (2). If commit start, dirty_znode
is set to COW_ZNODE in get_znodes_to_commit() in case of potentially ops
on this znode. We clear COW bit and DIRTY bit in write_index() without
@tnc_mutex locked. We don't increase @clean_zn_cnt in this place. As the
comments in write_index() shows, if another process hold @tnc_mutex and
dirty this znode after we clean it, @clean_zn_cnt would be decreased to (1).
We will increase @clean_zn_cnt to (2) with @tnc_mutex locked in
free_obsolete_znodes() to keep it right.

If shrink_tnc() performs between decrease and increase, it will release
other 2 clean znodes it holds and found @clean_zn_cnt is less than zero
(1 - 2 = -1), then hit the assertion. Because free_obsolete_znodes() will
soon correct @clean_zn_cnt and no harm to fs in this case, I think this
assertion could be removed.

2 clean zondes and 1 dirty znode, @clean_zn_cnt == 2

Thread A (commit)         Thread B (write or others)       Thread C (shrinker)
->write_index
   ->clear_bit(DIRTY_NODE)
   ->clear_bit(COW_ZNODE)

            @clean_zn_cnt == 2
                          ->mutex_locked(&tnc_mutex)
                          ->dirty_cow_znode
                              ->!ubifs_zn_cow(znode)
                              ->!test_and_set_bit(DIRTY_NODE)
                              ->atomic_dec(&clean_zn_cnt)
                          ->mutex_unlocked(&tnc_mutex)

            @clean_zn_cnt == 1
                                                           ->mutex_locked(&tnc_mutex)
                                                           ->shrink_tnc
                                                             ->destroy_tnc_subtree
                                                             ->atomic_sub(&clean_zn_cnt, 2)
                                                             ->ubifs_assert  <- hit
                                                           ->mutex_unlocked(&tnc_mutex)

            @clean_zn_cnt == -1
->mutex_lock(&tnc_mutex)
->free_obsolete_znodes
   ->atomic_inc(&clean_zn_cnt)
->mutux_unlock(&tnc_mutex)

            @clean_zn_cnt == 0 (correct after shrink)

Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UBIFS: fix an mmap and fsync race condition

commit 691a7c6f28ac90cccd0dbcf81348ea90b211bdd0 upstream.

There is a race condition in UBIFS:

Thread A (mmap)                        Thread B (fsync)

->__do_fault                           ->write_cache_pages
   -> ubifs_vm_page_mkwrite
       -> budget_space
       -> lock_page
       -> release/convert_page_budget
       -> SetPagePrivate
       -> TestSetPageDirty
       -> unlock_page
                                       -> lock_page
                                           -> TestClearPageDirty
                                           -> ubifs_writepage
                                               -> do_writepage
                                                   -> release_budget
                                                   -> ClearPagePrivate
                                                   -> unlock_page
   -> !(ret & VM_FAULT_LOCKED)
   -> lock_page
   -> set_page_dirty
       -> ubifs_set_page_dirty
           -> TestSetPageDirty (set page dirty without budgeting)
   -> unlock_page

This leads to situation where we have a diry page but no budget allocated for
this page, so further write-back may fail with -ENOSPC.

In this fix we return from page_mkwrite without performing unlock_page. We
return VM_FAULT_LOCKED instead. After doing this, the race above will not
happen.

Signed-off-by: hujianyang <hujianyang@huawei.com>
Tested-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region

commit ab6c15bc6620ebe220970cc040b29bcb2757f373 upstream.

Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:

CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c

Kernel panic - not syncing: Attempted to kill the idle task!

This patch fixes the problem

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7118/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

recordmcount/MIPS: Fix possible incorrect mcount_loc table entries in modules

commit 91ad11d7cc6f4472ebf177a6252fbf0fd100d798 upstream.

On MIPS calls to _mcount in modules generate 2 instructions to load
the _mcount address (and therefore 2 relocations). The mcount_loc
table should only reference the first of these, so the second is
filtered out by checking the relocation offset and ignoring ones that
immediately follow the previous one seen.

However if a module has an _mcount call at offset 0, the second
relocation would not be filtered out due to old_r_offset == 0
being taken to mean that the current relocation is the first one
seen, and both would end up in the mcount_loc table.

This results in ftrace_make_nop() patching both (adjacent)
instructions to branches over the _mcount call sequence like so:

  0xffffffffc08a8000:  04 00 00 10     b       0xffffffffc08a8014
  0xffffffffc08a8004:  04 00 00 10     b       0xffffffffc08a8018
  0xffffffffc08a8008:  2d 08 e0 03     move    at,ra
  ...

The second branch is in the delay slot of the first, which is
defined to be unpredictable - on the platform on which this bug was
encountered, it triggers a reserved instruction exception.

Fix by initializing old_r_offset to ~0 and using that instead of 0
to determine whether the current relocation is the first seen.

Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7098/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtip32xx: Remove dfs_parent after pci unregister

commit af5ded8ccf21627f9614afc03b356712666ed225 upstream.

In module exit, dfs_parent and it's subtree were removed before
unregistering with pci. When debugfs entry for each device is attempted
to remove in pci_remove() context, they don't exist, as dfs_parent and
its children were already ripped apart.

Modified to first unregister with pci and then remove dfs_parent.

Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtip32xx: Increase timeout for STANDBY IMMEDIATE command

commit 670a641420a3d9586eebe7429dfeec4e7ed447aa upstream.

Increased timeout for STANDBY IMMEDIATE command to 2 minutes.

Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtip32xx: Fix ERO and NoSnoop values in PCIe upstream on AMD systems

commit d1e714db8129a1d3670e449b87719c78e2c76f9f upstream.

A hardware quirk in P320h/P420m interfere with PCIe transactions on some
AMD chipsets, making P320h/P420m unusable. This workaround is to disable
ERO and NoSnoop bits in the parent and root complex for normal
functioning of these devices

NOTE: This workaround is specific to AMD chipset with a PCIe upstream
device with device id 0x5aXX

Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Fix incorrect vgaarb conditional in WARN_ON()

commit 67ebd8140dc8923c65451fa0f6a8eee003c4dcd3 upstream.

3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true.  Replace with logical AND.

Found by Coverity (CID 142811).

Fixes: 3448a19da479 "vgaarb: use bridges to control VGA routing where possible"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Add new ID for Intel GPU "spurious interrupt" quirk

commit 7c82126a94e69bbbac586f0249e7ef11e681246c upstream.

After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.

It turned out that the new CPU also featured a new GPU with a different PCI
ID.

Add this PCI ID to the quirk table.  Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.

See f67fd55fa96f ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.

[bhelgaas: add f67fd55fa96f reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elantech - don't set bit 1 of reg_10 when the no_hw_res quirk is set

commit fb4f8f568a9def02240ef9bf7aabd246dc63a081 upstream.

The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).

I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151

To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.

Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elantech - deal with clickpads reporting right button events

commit cd9e83e2754465856097f31c7ab933ce74c473f8 upstream.

At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:

https://bugzilla.redhat.com/show_bug.cgi?id=1103528

This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.

It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.

Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.

So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.

Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iscsi-target: Explicily clear login response PDU in exception path

commit 683497566d48f86e04d026de1ee658dd74fc1077 upstream.

This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().

This addresses a regression bug introduced in commit baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.

Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iscsi-target: Avoid rejecting incorrect ITT for Data-Out

commit 97c99b47ac58bacb7c09e1f47d5d184434f6b06a upstream.

This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.

This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.

Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Fix left-over se_lun->lun_sep pointer OOPs

commit 83ff42fcce070801a3aa1cd6a3269d7426271a8d upstream.

This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.

To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.

Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.46

iscsi-target: Re-add chunk from backport of upstream 79d59d08082d to 3.10

Commit d5c55fa31a29, the backport of upstream 79d59d08082d
("iscsi-target: Fix wrong buffer / buffer overrun in
iscsi_change_param_value()") left out applying one chunk of the fix in
iscsi_login_non_zero_tsih_s2().  Add the missing chunk.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86_32, entry: Do syscall exit work on badsys (CVE-2014-4508)

commit 554086d85e71f30abe46fc014fea31929a7c6a8a upstream.

The bad syscall nr paths are their own incomprehensible route
through the entry control flow.  Rearrange them to work just like
syscalls that return -ENOSYS.

This fixes an OOPS in the audit code when fast-path auditing is
enabled and sysenter gets a bad syscall nr (CVE-2014-4508).

This has probably been broken since Linux 2.6.27:
af0575bba0 i386 syscall audit fast-path

Cc: Roland McGrath <roland@redhat.com>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/e09c499eade6fc321266dd6b54da7beb28d6991c.1403558229.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Target/iser: Wait for proper cleanup before unloading

commit f5ebec9629cf78eeeea4b8258882a9f439ab2404 upstream.

disconnected_handler works are scheduled on system_wq.
When attempting to unload, first make sure all works
have cleaned up.

Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Target/iser: Improve cm events handling

commit 88c4015fda6d014392f76d3b1688347950d7a12d upstream.

There are 4 RDMA_CM events that all basically mean that
the user should teardown the IB connection:
- DISCONNECTED
- ADDR_CHANGE
- DEVICE_REMOVAL
- TIMEWAIT_EXIT

Only in DISCONNECTED/ADDR_CHANGE it makes sense to
call rdma_disconnect (send DREQ/DREP to our initiator).
So we keep the same teardown handler for all of them
but only indicate calling rdma_disconnect for the relevant
events.

This patch also removes redundant debug prints for each single
event.

v2 changes:
 - Call isert_disconnected_handler() for DEVICE_REMOVAL (Or + Sag)

Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: usbtest: Add timetout to simple_io()

commit e5e4746510d140261918aecce2e5e3aa4456f7e9 upstream.

Without a timetout some tests e.g. test_halt() can remain stuck forever.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix use of uninit "ret" in end_extent_writepage()

commit 3e2426bd0eb980648449e7a2f5a23e3cd3c7725c upstream.

If this condition in end_extent_writepage() is false:

if (tree->ops && tree->ops->writepage_end_io_hook)

we will then test an uninitialized "ret" at:

ret = ret < 0 ? ret : -EIO;

The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.

Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.

Signed-of-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: fix scrub_print_warning to handle skinny metadata extents

commit 6eda71d0c030af0fc2f68aaa676e6d445600855b upstream.

The skinny extents are intepreted incorrectly in scrub_print_warning(),
and end up hitting the BUG() in btrfs_extent_inline_ref_size.

Reported-by: Konstantinos Skarlatos <k.skarlatos@gmail.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: use right type to get real comparison

commit cd857dd6bc2ae9ecea14e75a34e8a8fdc158e307 upstream.

We want to make sure the point is still within the extent item, not to verify
the memory it's pointing to.

Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: btrfs: volumes.c: Fix for possible null pointer dereference

commit 8321cf2596d283821acc466377c2b85bcd3422b7 upstream.

There is otherwise a risk of a possible null pointer dereference.

Was largely found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: send, don't error in the presence of subvols/snapshots

commit 1af56070e3ef9477dbc7eba3b9ad7446979c7974 upstream.

If we are doing an incremental send and the base snapshot has a
directory with name X that doesn't exist anymore in the second
snapshot and a new subvolume/snapshot exists in the second snapshot
that has the same name as the directory (name X), the incremental
send would fail with -ENOENT error. This is because it attempts
to lookup for an inode with a number matching the objectid of a
root, which doesn't exist.

Steps to reproduce:

    mkfs.btrfs -f /dev/sdd
    mount /dev/sdd /mnt

    mkdir /mnt/testdir
    btrfs subvolume snapshot -r /mnt /mnt/mysnap1

    rmdir /mnt/testdir
    btrfs subvolume create /mnt/testdir
    btrfs subvolume snapshot -r /mnt /mnt/mysnap2

    btrfs send -p /mnt/mysnap1 /mnt/mysnap2 -f /tmp/send.data

A test case for xfstests follows.

Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: set right total device count for seeding support

commit 298658414a2f0bea1f05a81876a45c1cd96aa2e0 upstream.

Seeding device support allows us to create a new filesystem
based on existed filesystem.

However newly created filesystem's @total_devices should include seed
devices. This patch fix the following problem:

 # mkfs.btrfs -f /dev/sdb
 # btrfstune -S 1 /dev/sdb
 # mount /dev/sdb /mnt
 # btrfs device add -f /dev/sdc /mnt --->fs_devices->total_devices = 1
 # umount /mnt
 # mount /dev/sdc /mnt               --->fs_devices->total_devices = 2

This is because we record right @total_devices in superblock, but
@fs_devices->total_devices is reset to be 0 in btrfs_prepare_sprout().

Fix this problem by not resetting @fs_devices->total_devices.

Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: mark mapping with error flag to report errors to userspace

commit 5dca6eea91653e9949ce6eb9e9acab6277e2f2c4 upstream.

According to commit 865ffef3797da2cac85b3354b5b6050dc9660978
(fs: fix fsync() error reporting),
it's not stable to just check error pages because pages can be
truncated or invalidated, we should also mark mapping with error
flag so that a later fsync can catch the error.

Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: make sure there are not any read requests before stopping workers

commit de348ee022175401e77d7662b7ca6e231a94e3fd upstream.

In close_ctree(), after we have stopped all workers,there maybe still
some read requests(for example readahead) to submit and this *maybe* trigger
an oops that user reported before:

kernel BUG at fs/btrfs/async-thread.c:619!

By hacking codes, i can reproduce this problem with one cpu available.
We fix this potential problem by invalidating all btree inode pages before
stopping all workers.

Thanks to Miao for pointing out this problem.

Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: output warning instead of error when loading free space cache failed

commit 32d6b47fe6fc1714d5f1bba1b9f38e0ab0ad58a8 upstream.

If we fail to load a free space cache, we can rebuild it from the extent tree,
so it is not a serious error, we should not output a error message that
would make the users uncomfortable. This patch uses warning message instead
of it.

Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: Add ctime/mtime update for btrfs device add/remove.

commit 5a1972bd9fd4b2fb1bac8b7a0b636d633d8717e3 upstream.

Btrfs will send uevent to udev inform the device change,
but ctime/mtime for the block device inode is not udpated, which cause
libblkid used by btrfs-progs unable to detect device change and use old
cache, causing 'btrfs dev scan; btrfs dev rmove; btrfs dev scan' give an
error message.

Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: fix double free in find_lock_delalloc_range

commit 7d78874273463a784759916fc3e0b4e2eb141c70 upstream.

We need to NULL the cached_state after freeing it, otherwise
we might free it again if find_delalloc_range doesn't find anything.

Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

skbuff: skb_segment: orphan frags before copying

commit 1fd819ecb90cc9b822cd84d3056ddba315d3340f upstream.

skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.

skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2.  As skb_segment() only supports page-frags *or* a
  frag list, there is no need for the additional frag_skb pointer or the
  preparatory renaming.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Eddie Chapman <eddie@ehuk.net> # backported to 3.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aio: fix kernel memory disclosure in io_getevents() introduced in v3.10

commit edfbbf388f293d70bf4b7c0bc38774d05e6f711a upstream.

A kernel memory disclosure was introduced in aio_read_events_ring() in v3.10
by commit a31ad380bed817aa25f8830ad23e1a0480fef797.  The changes made to
aio_read_events_ring() failed to correctly limit the index into
ctx->ring_pages[], allowing an attacked to cause the subsequent kmap() of
an arbitrary page with a copy_to_user() to copy the contents into userspace.
This vulnerability has been assigned CVE-2014-0206.  Thanks to Mateusz and
Petr for disclosing this issue.

This patch applies to v3.12+.  A separate backport is needed for 3.10/3.11.

[jmoyer@redhat.com: backported to 3.10]
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aio: fix aio request leak when events are reaped by userspace

commit f8567a3845ac05bb28f3c1b478ef752762bd39ef upstream.

The aio cleanups and optimizations by kmo that were merged into the 3.10
tree added a regression for userspace event reaping.  Specifically, the
reference counts are not decremented if the event is reaped in userspace,
leading to the application being unable to submit further aio requests.
This patch applies to 3.12+.  A separate backport is required for 3.10/3.11.
This issue was uncovered as part of CVE-2014-0206.

[jmoyer@redhat.com: backported to 3.10]
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq: Sanitize spurious interrupt detection of threaded irqs

commit 1e77d0a1ed7417d2a5a52a7b8d32aea1833faa6c upstream.

Till reported that the spurious interrupt detection of threaded
interrupts is broken in two ways:

- note_interrupt() is called for each action thread of a shared
  interrupt line. That's wrong as we are only interested whether none
  of the device drivers felt responsible for the interrupt, but by
  calling multiple times for a single interrupt line we account
  IRQ_NONE even if one of the drivers felt responsible.

- note_interrupt() when called from the thread handler is not
  serialized. That leaves the members of irq_desc which are used for
  the spurious detection unprotected.

To solve this we need to defer the spurious detection of a threaded
interrupt to the next hardware interrupt context where we have
implicit serialization.

If note_interrupt is called with action_ret == IRQ_WAKE_THREAD, we
check whether the previous interrupt requested a deferred check. If
not, we request a deferred check for the next hardware interrupt and
return.

If set, we check whether one of the interrupt threads signaled
success. Depending on this information we feed the result into the
spurious detector.

If one primary handler of a shared interrupt returns IRQ_HANDLED we
disable the deferred check of irq threads on the same line, as we have
found at least one device driver who cared.

Reported-by: Till Straumann <strauman@slac.stanford.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1303071450130.22263@ionos
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, x32: Use compat shims for io_{setup,submit}

commit 7fd44dacdd803c0bbf38bf478d51d280902bb0f1 upstream.

The io_setup takes a pointer to a context id of type aio_context_t.
This in turn is typed to a __kernel_ulong_t.  We could tweak the
exported headers to define this as a 64bit quantity for specific
ABIs, but since we already have a 32bit compat shim for the x86 ABI,
let's just re-use that logic.  The libaio package is also written to
expect this as a pointer type, so a compat shim would simplify that.

The io_submit func operates on an array of pointers to iocb structs.
Padding out the array to be 64bit aligned is a huge pain, so convert
it over to the existing compat shim too.

We don't convert io_getevents to the compat func as its only purpose
is to handle the timespec struct, and the x32 ABI uses 64bit times.

With this change, the libaio package can now pass its testsuite when
built for the x32 ABI.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Link: http://lkml.kernel.org/r/1399250595-5005-1-git-send-email-vapier@gentoo.org
Cc: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86-32, espfix: Remove filter for espfix32 due to race

commit 246f2d2ee1d715e1077fc47d61c394569c8ee692 upstream.

It is not safe to use LAR to filter when to go down the espfix path,
because the LDT is per-process (rather than per-thread) and another
thread might change the descriptors behind our back.  Fortunately it
is always *safe* (if a bit slow) to go down the espfix path, and a
32-bit LDT stack segment is extremely rare.

Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1398816946-3351-1-git-send-email-hpa@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Explicitly clear ramdisk_mcp backend pages

[Note that a different patch to address the same issue went in during
v3.15-rc1 (commit 4442dc8a), but includes a bunch of other changes that
don't strictly apply to fixing the bug]

This patch changes rd_allocate_sgl_table() to explicitly clear
ramdisk_mcp backend memory pages by passing __GFP_ZERO into
alloc_pages().

This addresses a potential security issue where reading from a
ramdisk_mcp could return sensitive information, and follows what
>= v3.15 does to explicitly clear ramdisk_mcp memory at backend
device initialization time.

Reported-by: Jorge Daniel Sequeira Matias <jdsm@tecnico.ulisboa.pt>
Cc: Jorge Daniel Sequeira Matias <jdsm@tecnico.ulisboa.pt>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Report correct response length for some commands

commit 2426bd456a61407388b6e61fc5f98dbcbebc50e2 upstream.

When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.

Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.

This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:

  http://permalink.gmane.org/gmane.linux.scsi.target.devel/6515

Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak

commit bbc050488525e1ab1194c27355f63c66814385b8 upstream.

This patch fixes a iscsi_queue_req memory leak when ABORT_TASK response
has been queued by TFO->queue_tm_rsp() -> lio_queue_tm_rsp() after a
long standing I/O completes, but the connection has already reset and
waiting for cleanup to complete in iscsit_release_commands_from_conn()
-> transport_generic_free_cmd() -> transport_wait_for_tasks() code.

It moves iscsit_free_queue_reqs_for_conn() after the per-connection command
list has been released, so that the associated se_cmd tag can be completed +
released by target-core before freeing any remaining iscsi_queue_req memory
for the connection generated by lio_queue_tm_rsp().

Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Use complete_all for se_cmd->t_transport_stop_comp

commit a95d6511303b848da45ee27b35018bb58087bdc6 upstream.

This patch fixes a bug where multiple waiters on ->t_transport_stop_comp
occurs due to a concurrent ABORT_TASK and session reset both invoking
transport_wait_for_tasks(), while waiting for the associated se_cmd
descriptor backend processing to complete.

For this case, complete_all() should be invoked in order to wake up
both waiters in core_tmr_abort_task() + transport_generic_free_cmd()
process contexts.

Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target: Set CMD_T_ACTIVE bit for Task Management Requests

commit f15e9cd910c4d9da7de43f2181f362082fc45f0f upstream.

This patch fixes a bug where se_cmd descriptors associated with a
Task Management Request (TMR) where not setting CMD_T_ACTIVE before
being dispatched into target_tmr_work() process context.

This is required in order for transport_generic_free_cmd() ->
transport_wait_for_tasks() to wait on se_cmd->t_transport_stop_comp
if a session reset event occurs while an ABORT_TASK is outstanding
waiting for another I/O to complete.

Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Target/iser: Fix hangs in connection teardown

commit 9d49f5e284e700576f3b65f1e28dea8539da6661 upstream.

In ungraceful teardowns isert close flows seem racy such that
isert_wait_conn hangs as RDMA_CM_EVENT_DISCONNECTED never
gets invoked (no one called rdma_disconnect).

Both graceful and ungraceful teardowns will have rx flush errors
(isert posts a batch once connection is established). Once all
flush errors are consumed we invoke isert_wait_conn and it will
be responsible for calling rdma_disconnect. This way it can be
sure that rdma_disconnect was called and it won't wait forever.

This patch also removes the logout_posted indicator. either the
logout completion was consumed and no problem decrementing the
post_send_buf_count, or it was consumed as a flush error. no point
of keeping it for isert_wait_conn as there is no danger that
isert_conn will be accidentally removed while it is running.

(Drop unnecessary sleep_on_conn_wait_comp check in
 isert_cq_rx_comp_err - nab)

Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Target/iser: Bail from accept_np if np_thread is trying to close

commit e346ab343f4f58c12a96725c7b13df9cc2ad56f6 upstream.

In case np_thread state is in RESET/SHUTDOWN/EXIT states,
no point for isert to stall there as we may get a hang in
case no one will wake it up later.

Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix L2CAP deadlock

commit 8a96f3cd22878fc0bb564a8478a6e17c0b8dca73 upstream.

-[0x01 Introduction

We have found a programming error causing a deadlock in Bluetooth subsystem
of Linux kernel. The problem is caused by missing release_sock() call when
L2CAP connection creation fails due full accept queue.

The issue can be reproduced with 3.15-rc5 kernel and is also present in
earlier kernels.

-[0x02 Details

The problem occurs when multiple L2CAP connections are created to a PSM which
contains listening socket (like SDP) and left pending, for example,
configuration (the underlying ACL link is not disconnected between
connections).

When L2CAP connection request is received and listening socket is found the
l2cap_sock_new_connection_cb() function (net/bluetooth/l2cap_sock.c) is called.
This function locks the 'parent' socket and then checks if the accept queue
is full.

1178         lock_sock(parent);
1179
1180         /* Check for backlog size */
1181         if (sk_acceptq_is_full(parent)) {
1182                 BT_DBG("backlog full %d", parent->sk_ack_backlog);
1183                 return NULL;
1184         }

If case the accept queue is full NULL is returned, but the 'parent' socket
is not released. Thus when next L2CAP connection request is received the code
blocks on lock_sock() since the parent is still locked.

Also note that for connections already established and waiting for
configuration to complete a timeout will occur and l2cap_chan_timeout()
(net/bluetooth/l2cap_core.c) will be called. All threads calling this
function will also be blocked waiting for the channel mutex since the thread
which is waiting on lock_sock() alread holds the channel mutex.

We were able to reproduce this by sending continuously L2CAP connection
request followed by disconnection request containing invalid CID. This left
the created connections pending configuration.

After the deadlock occurs it is impossible to kill bluetoothd, btmon will not
get any more data etc. requiring reboot to recover.

-[0x03 Fix

Releasing the 'parent' socket when l2cap_sock_new_connection_cb() returns NULL
seems to fix the issue.

Signed-off-by: Jukka Taimisto <jtt@codenomicon.com>
Reported-by: Tommi Mäkilä <tmakila@codenomicon.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bluetooth: hci_ldisc: fix deadlock condition

commit da64c27d3c93ee9f89956b9de86c4127eb244494 upstream.

LDISCs shouldn't call tty->ops->write() from within
->write_wakeup().

->write_wakeup() is called with port lock taken and
IRQs disabled, tty->ops->write() will try to acquire
the same port lock and we will deadlock.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Andreas Bießmann <andreas@biessmann.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8037/1: mm: support big-endian page tables

commit 86f40622af7329375e38f282f6c0aab95f3e5f72 upstream.

When enable LPAE and big-endian in a hisilicon board, while specify
mem=384M mem=512M@7680M, will get bad page state:

Freeing unused kernel memory: 180K (c0466000 - c0493000)
BUG: Bad page state in process init  pfn:fa442
page:c7749840 count:0 mapcount:-1 mapping:  (null) index:0x0
page flags: 0x40000400(reserved)
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 3.10.27+ #66
[<c000f5f0>] (unwind_backtrace+0x0/0x11c) from [<c000cbc4>] (show_stack+0x10/0x14)
[<c000cbc4>] (show_stack+0x10/0x14) from [<c009e448>] (bad_page+0xd4/0x104)
[<c009e448>] (bad_page+0xd4/0x104) from [<c009e520>] (free_pages_prepare+0xa8/0x14c)
[<c009e520>] (free_pages_prepare+0xa8/0x14c) from [<c009f8ec>] (free_hot_cold_page+0x18/0xf0)
[<c009f8ec>] (free_hot_cold_page+0x18/0xf0) from [<c00b5444>] (handle_pte_fault+0xcf4/0xdc8)
[<c00b5444>] (handle_pte_fault+0xcf4/0xdc8) from [<c00b6458>] (handle_mm_fault+0xf4/0x120)
[<c00b6458>] (handle_mm_fault+0xf4/0x120) from [<c0013754>] (do_page_fault+0xfc/0x354)
[<c0013754>] (do_page_fault+0xfc/0x354) from [<c0008400>] (do_DataAbort+0x2c/0x90)
[<c0008400>] (do_DataAbort+0x2c/0x90) from [<c0008fb4>] (__dabt_usr+0x34/0x40)

The bad pfn:fa442 is not system memory(mem=384M mem=512M@7680M), after debugging,
I find in page fault handler, will get wrong pfn from pte just after set pte,
as follow:
do_anonymous_page()
{
...
set_pte_at(mm, address, page_table, entry);

//debug code
pfn = pte_pfn(entry);
pr_info("pfn:0x%lx, pte:0x%llxn", pfn, pte_val(entry));

//read out the pte just set
new_pte = pte_offset_map(pmd, address);
new_pfn = pte_pfn(*new_pte);
pr_info("new pfn:0x%lx, new pte:0x%llxn", pfn, pte_val(entry));
...
}

pfn:   0x1fa4f5,     pte:0xc00001fa4f575f
new_pfn:0xfa4f5, new_pte:0xc00000fa4f5f5f //new pfn/pte is wrong.

The bug is happened in cpu_v7_set_pte_ext(ptep, pte):
An LPAE PTE is a 64bit quantity, passed to cpu_v7_set_pte_ext in the r2 and r3 registers.
On an LE kernel, r2 contains the LSB of the PTE, and r3 the MSB.
On a BE kernel, the assignment is reversed.

Unfortunately, the current code always assumes the LE case,
leading to corruption of the PTE when clearing/setting bits.

This patch fixes this issue much like it has been done already in the
cpu_v7_switch_mm case.

Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: stacktrace: avoid listing stacktrace functions in stacktrace

commit 3683f44c42e991d313dc301504ee0fca1aeb8580 upstream.

While debugging the FEC ethernet driver using stacktrace, it was noticed
that the stacktraces always begin as follows:

 [<c00117b4>] save_stack_trace_tsk+0x0/0x98
 [<c0011870>] save_stack_trace+0x24/0x28
 ...

This is because the stack trace code includes the stack frames for itself.
This is incorrect behaviour, and also leads to "skip" doing the wrong
thing (which is the number of stack frames to avoid recording.)

Perversely, it does the right thing when passed a non-current thread.  Fix
this by ensuring that we have a known constant number of frames above the
main stack trace function, and always skip these.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: uvcvideo: Fix clock param realtime setting

commit 3b35fc81e7ec552147a4fd843d0da0bbbe4ef253 upstream.

timestamps in v4l2 buffers returned to userspace are updated in
uvc_video_clock_update() which uses timestamps fetched from
uvc_video_clock_decode() by calling unconditionally ktime_get_ts().

Hence setting the module clock param to realtime has no effect before
this patch.

This has been tested with ffmpeg:

ffmpeg -y -f v4l2 -input_format yuyv422 -video_size 640x480 -framerate 30 -i /dev/video0 \
 -f alsa -acodec pcm_s16le -ar 16000 -ac 1 -i default \
 -c:v libx264 -preset ultrafast \
 -c:a libfdk_aac \
 out.mkv

and inspecting the v4l2 input starting timestamp.

Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI: Fix conflict between customized DSDT and DSDT local copy

commit 73577d1df8e1f31f6b1a5eebcdbc334eb0330e47 upstream.

This patch fixes the following issue:
If DSDT is customized, no local DSDT copy is needed.

References: https://bugzilla.kernel.org/show_bug.cgi?id=69711
Signed-off-by: Enrico Etxe Arte <goitizena.generoa@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPICA: utstring: Check array index bound before use.

commit 5d42b0fa25df7ef2f575107597c1aaebe2407d10 upstream.

ACPICA BZ 1077. David Binderman.

References: https://bugs.acpica.org/show_bug.cgi?id=1077
Signed-off-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: stk1160: Avoid stack-allocated buffer for control URBs

commit 85ac1a1772bb41da895bad83a81f6a62c8f293f6 upstream.

Currently stk1160_read_reg() uses a stack-allocated char to get the
read control value. This is wrong because usb_control_msg() requires
a kmalloc-ed buffer.

This commit fixes such issue by kmalloc'ating a 1-byte buffer to receive
the read value.

While here, let's remove the urb_buf array which was meant for a similar
purpose, but never really used.

Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: ivtv: Fix Oops when no firmware is loaded

commit deb29e90221a6d4417aa67be971613c353180331 upstream.

When ivtv PCM device is accessed at the state where no firmware is
loaded, it oopses like:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
  IP: [<ffffffffa049a881>] try_mailbox.isra.0+0x11/0x50 [ivtv]
  Call Trace:
    [<ffffffffa049aa20>] ivtv_api_call+0x160/0x6b0 [ivtv]
    [<ffffffffa049af86>] ivtv_api+0x16/0x40 [ivtv]
    [<ffffffffa049b10c>] ivtv_vapi+0xac/0xc0 [ivtv]
    [<ffffffffa049d40d>] ivtv_start_v4l2_encode_stream+0x19d/0x630 [ivtv]
    [<ffffffffa0530653>] snd_ivtv_pcm_capture_open+0x173/0x1c0 [ivtv_alsa]
    [<ffffffffa04526f1>] snd_pcm_open_substream+0x51/0x100 [snd_pcm]
    [<ffffffffa0452853>] snd_pcm_open+0xb3/0x260 [snd_pcm]
    [<ffffffffa0452a37>] snd_pcm_capture_open+0x37/0x50 [snd_pcm]
    [<ffffffffa033f557>] snd_open+0xa7/0x1e0 [snd]
    [<ffffffff8118a628>] chrdev_open+0x88/0x1d0
    [<ffffffff811840be>] do_dentry_open+0x1de/0x270
    [<ffffffff81193a73>] do_last+0x1c3/0xec0
    [<ffffffff81194826>] path_openat+0xb6/0x670
    [<ffffffff81195b65>] do_filp_open+0x35/0x80
    [<ffffffff81185449>] do_sys_open+0x129/0x210
    [<ffffffff815b782d>] system_call_fastpath+0x1a/0x1f

This patch adds the check of firmware at PCM open callback like other
open callbacks of this driver.

Bugzilla: https://apibugzilla.novell.com/show_bug.cgi?id=875440

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: fix potential runtime pm imbalance at device remove

commit c14829fad88dbeda57253590695b85ba51270621 upstream.

Only call usb_autopm_put_interface() if the corresponding
usb_autopm_get_interface() was successful.

This prevents a potential runtime PM counter imbalance should
usb_autopm_get_interface() fail. Note that the USB PM usage counter is
reset when the interface is unbound, but that the runtime PM counter may
be left unbalanced.

Also add comment on why we don't need to worry about racing
resume/suspend on autopm_get failures.

Fixes: d5fd650cfc7f ("usb: serial: prevent suspend/resume from racing
against probe/remove")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: qcserial: add additional Sierra Wireless QMI devices

commit 0ce5fb58564fd85aa8fd2d24209900e2e845317b upstream.

A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Link: http://marc.info/?l=linux-usb&m=140136310027293&w=2
Cc: <stable@vger.kernel.org> # backport in link above
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: qcserial: add Netgear AirCard 341U

commit ff1fcd50bc2459744e6f948310bc18eb7d6e8c72 upstream.

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: sierra: fix remote wakeup

commit 80cc0fcbdaeaf10d04ba27779a2d7ceb73d2717a upstream.

Make sure that needs_remote_wake up is always set when there are open
ports.

Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).

Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.

Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: sierra: fix urb and memory leak on disconnect

commit 014333f77c0b71123d6ef7d31a9724e0699c9548 upstream.

The delayed-write queue was never emptied on disconnect, something which
would lead to leaked urbs and transfer buffers if the device is
disconnected before being runtime resumed due to a write.

Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: sierra: fix urb and memory leak in resume error path

commit 7fdd26a01eb7b6cb6855ff8f69ef4a720720dfcb upstream.

Neither the transfer buffer or the urb itself were released in the
resume error path for delayed writes. Also on errors, the remainder of
the queue was not even processed, which leads to further urb and buffer
leaks.

The same error path also failed to balance the outstanding-urb counter,
something which results in degraded throughput or completely blocked
writes.

Fix this by releasing urb and buffer and balancing counters on errors,
and by always processing the whole queue even when submission of one urb
fails.

Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: sierra: fix use after free at suspend/resume

commit 8452727de70f6ad850cd6d0aaa18b5d9050aa63b upstream.

Fix use after free or NULL-pointer dereference during suspend and
resume.

The port data may never have been allocated (port probe failed)
or may already have been released by port_remove (e.g. driver is
unloaded) when suspend and resume are called.

Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: sierra: fix AA deadlock in open error path

commit 353fe198602e8b4d1c7bdcceb8e60955087201b1 upstream.

Fix AA deadlock in open error path that would call close() and try to
grab the already held disc_mutex.

Fixes: b9a44bc19f48 ("sierra: driver urb handling improvements")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix potential blocked I/O after resume

commit fb7ad4f93d9f0f7d49beda32f5e7becb94b29a4d upstream.

Keep trying to submit urbs rather than bail out on first read-urb
submission error, which would also prevent I/O for any further ports
from being resumed.

Instead keep an error count, for all types of failed submissions, and
let USB core know that something went wrong.

Also make sure to always clear the suspended flag. Currently a failed
read-urb submission would prevent cached writes as well as any
subsequent writes from being submitted until next suspend-resume cycle,
something which may not even necessarily happen.

Note that USB core currently only logs an error if an interface resume
failed.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix potential NULL-deref at resume

commit 9096f1fbba916c2e052651e9de82fcfb98d4bea7 upstream.

The interrupt urb was submitted unconditionally at resume, something
which could lead to a NULL-pointer dereference in the urb completion
handler as resume may be called after the port and port data is gone.

Fix this by making sure the interrupt urb is only submitted and active
when the port is open.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix urb leak at shutdown

commit 79eed03e77d481b55d85d1cfe5a1636a0d3897fd upstream.

The delayed-write queue was never emptied at shutdown (close), something
which could lead to leaked urbs if the port is closed before being
runtime resumed due to a write.

When this happens the output buffer would not drain on close
(closing_wait timeout), and after consecutive opens, writes could be
corrupted with previously buffered data, transfered with reduced
throughput or completely blocked.

Note that unbusy_queued_urb() was simply moved out of CONFIG_PM.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix write and suspend race

commit 170fad9e22df0063eba0701adb966786d7a4ec5a upstream.

Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.

Specifically, suspend() releases the susp_lock after determining the
device is idle but before setting the suspended flag, thus leaving a
window where a concurrent write() can submit an urb.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix race between write and resume

commit d9e93c08d8d985e5ef89436ebc9f4aad7e31559f upstream.

We find a race between write and resume. usb_wwan_resume run play_delayed()
and spin_unlock, but intfdata->suspended still is not set to zero.
At this time usb_wwan_write is called and anchor the urb to delay
list. Then resume keep running but the delayed urb have no chance
to be commit until next resume. If the time of next resume is far
away, tty will be blocked in tty_wait_until_sent during time. The
race also can lead to writes being reordered.

This patch put play_Delayed and intfdata->suspended together in the
spinlock, it's to avoid the write race during resume.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix urb leak in write error path

commit db0904737947d509844e171c9863ecc5b4534005 upstream.

When enable usb serial for modem data, sometimes the tty is blocked
in tty_wait_until_sent because portdata->out_busy always is set and
have no chance to be cleared.

We find a bug in write error path. usb_wwan_write set portdata->out_busy
firstly, then try autopm async with error. No out urb submit and no
usb_wwan_outdat_callback to this write, portdata->out_busy can't be
cleared.

This patch clear portdata->out_busy if usb_wwan_write try autopm async
with error.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

matroxfb: perform a dummy read of M_STATUS

commit 972754cfaee94d6e25acf94a497bc0a864d91b7e upstream.

I had occasional screen corruption with the matrox framebuffer driver and
I found out that the reason for the corruption is that the hardware
blitter accesses the videoram while it is being written to.

The matrox driver has a macro WaitTillIdle() that should wait until the
blitter is idle, but it sometimes doesn't work. I added a dummy read
mga_inl(M_STATUS) to WaitTillIdle() to fix the problem. The dummy read
will flush the write buffer in the PCI chipset, and the next read of
M_STATUS will return the hardware status.

Since applying this patch, I had no screen corruption at all.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix wrong assert in ext4_mb_normalize_request()

commit b5b60778558cafad17bbcbf63e0310bd3c68eb17 upstream.

The variable "size" is expressed as number of blocks and not as
number of clusters, this could trigger a kernel panic when using
ext4 with the size of a cluster different from the size of a block.

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix zeroing of page during writeback

commit eeece469dedadf3918bad50ad80f4616a0064e90 upstream.

Tail of a page straddling inode size must be zeroed when being written
out due to POSIX requirement that modifications of mmaped page beyond
inode size must not be written to the file. ext4_bio_write_page() did
this only for blocks fully beyond inode size but didn't properly zero
blocks partially beyond inode size. Fix this.

The problem has been uncovered by mmap_11-4 test in openposix test suite
(part of LTP).

Reported-by: Xiaoguang Wang <wangxg.fnst@cn.fujitsu.com>
Fixes: 5a0dc7365c240
Fixes: bd2d0210cf22f
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/lowcore: reserve 96 bytes for IRB in lowcore

commit 993072ee67aa179c48c85eb19869804e68887d86 upstream.

The IRB might be 96 bytes if the extended-I/O-measurement facility is
used. This feature is currently not used by Linux, but struct irb
already has the emw defined. So let's make the irb in lowcore match the
size of the internal data structure to be future proof.
We also have to add a pad, to correctly align the paste.

The bigger irb field also circumvents a bug in some QEMU versions that
always write the emw field on test subchannel and therefore destroy the
paste definitions of this CPU. Running under these QEMU version broke
some timing functions in the VDSO and all users of these functions,
e.g. some JREs.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

idr: fix overflow bug during maximum ID calculation at maximum height

commit 3afb69cb5572b3c8c898c00880803cf1a49852c4 upstream.

idr_replace() open-codes the logic to calculate the maximum valid ID
given the height of the idr tree; unfortunately, the open-coded logic
doesn't account for the fact that the top layer may have unused slots
and over-shifts the limit to zero when the tree is at its maximum
height.

The following test code shows it fails to replace the value for
id=((1<<27)+42):

  static void test5(void)
  {
        int id;
        DEFINE_IDR(test_idr);
  #define TEST5_START ((1<<27)+42) /* use the highest layer */

        printk(KERN_INFO "Start test5\n");
        id = idr_alloc(&test_idr, (void *)1, TEST5_START, 0, GFP_KERNEL);
        BUG_ON(id != TEST5_START);
        TEST_BUG_ON(idr_replace(&test_idr, (void *)2, TEST5_START) != (void *)1);
        idr_destroy(&test_idr);
        printk(KERN_INFO "End of test5\n");
  }

Fix the bug by using idr_max() which correctly takes into account the
maximum allowed shift.

sub_alloc() shares the same problem and may incorrectly fail with
-EAGAIN; however, this bug doesn't affect correct operation because
idr_get_empty_slot(), which already uses idr_max(), retries with the
increased @id in such cases.

[tj@kernel.org: Updated patch description.]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: ptrace: change fs when passing kernel pointer to regset code

commit c168870704bcde6bb63d05f7882b620dd3985a46 upstream.

Our compat PTRACE_POKEUSR implementation simply passes the user data to
regset_copy_from_user after some simple range checking. Unfortunately,
the data in question has already been copied to the kernel stack by this
point, so the subsequent access_ok check fails and the ptrace request
returns -EFAULT. This causes problems tracing fork() with older versions
of strace.

This patch briefly changes the fs to KERNEL_DS, so that the access_ok
check passes even with a kernel address.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ptrace: fix fork event messages across pid namespaces

commit 4e52365f279564cef0ddd41db5237f0471381093 upstream.

When tracing a process in another pid namespace, it's important for fork
event messages to contain the child's pid as seen from the tracer's pid
namespace, not the parent's.  Otherwise, the tracer won't be able to
correlate the fork event with later SIGTRAP signals it receives from the
child.

We still risk a race condition if a ptracer from a different pid
namespace attaches after we compute the pid_t value.  However, sending a
bogus fork event message in this unlikely scenario is still a vast
improvement over the status quo where we always send bogus fork event
messages to debuggers in a different pid namespace than the forking
process.

Signed-off-by: Matthew Dempsky <mdempsky@chromium.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Julien Tinnes <jln@chromium.org>
Cc: Roland McGrath <mcgrathr@chromium.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: vmscan: clear kswapd's special reclaim powers before exiting

commit 71abdc15adf8c702a1dd535f8e30df50758848d2 upstream.

When kswapd exits, it can end up taking locks that were previously held
by allocating tasks while they waited for reclaim.  Lockdep currently
warns about this:

On Wed, May 28, 2014 at 06:06:34PM +0800, Gu Zheng wrote:
>  inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-R} usage.
>  kswapd2/1151 [HC0[0]:SC0[0]:HE1:SE1] takes:
>   (&sig->group_rwsem){+++++?}, at: exit_signals+0x24/0x130
>  {RECLAIM_FS-ON-W} state was registered at:
>     mark_held_locks+0xb9/0x140
>     lockdep_trace_alloc+0x7a/0xe0
>     kmem_cache_alloc_trace+0x37/0x240
>     flex_array_alloc+0x99/0x1a0
>     cgroup_attach_task+0x63/0x430
>     attach_task_by_pid+0x210/0x280
>     cgroup_procs_write+0x16/0x20
>     cgroup_file_write+0x120/0x2c0
>     vfs_write+0xc0/0x1f0
>     SyS_write+0x4c/0xa0
>     tracesys+0xdd/0xe2
>  irq event stamp: 49
>  hardirqs last  enabled at (49):  _raw_spin_unlock_irqrestore+0x36/0x70
>  hardirqs last disabled at (48):  _raw_spin_lock_irqsave+0x2b/0xa0
>  softirqs last  enabled at (0):  copy_process.part.24+0x627/0x15f0
>  softirqs last disabled at (0):            (null)
>
>  other info that might help us debug this:
>   Possible unsafe locking scenario:
>
>         CPU0
>         ----
>    lock(&sig->group_rwsem);
>    <Interrupt>
>      lock(&sig->group_rwsem);
>
>   *** DEADLOCK ***
>
>  no locks held by kswapd2/1151.
>
>  stack backtrace:
>  CPU: 30 PID: 1151 Comm: kswapd2 Not tainted 3.10.39+ #4
>  Call Trace:
>    dump_stack+0x19/0x1b
>    print_usage_bug+0x1f7/0x208
>    mark_lock+0x21d/0x2a0
>    __lock_acquire+0x52a/0xb60
>    lock_acquire+0xa2/0x140
>    down_read+0x51/0xa0
>    exit_signals+0x24/0x130
>    do_exit+0xb5/0xa50
>    kthread+0xdb/0x100
>    ret_from_fork+0x7c/0xb0

This is because the kswapd thread is still marked as a reclaimer at the
time of exit.  But because it is exiting, nobody is actually waiting on
it to make reclaim progress anymore, and it's nothing but a regular
thread at this point.  Be tidy and strip it of all its powers
(PF_MEMALLOC, PF_SWAPWRITE, PF_KSWAPD, and the lockdep reclaim state)
before returning from the thread function.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: core: fix validation of report id 0

commit 1b15d2e5b8077670b1e6a33250a0d9577efff4a5 upstream.

Some drivers use the first HID report in the list instead of using an
index. In these cases, validation uses ID 0, which was supposed to mean
"first known report". This fixes the problem, which was causing at least
the lgff family of devices to stop working since hid_validate_values
was being called with ID 0, but the devices used single numbered IDs
for their reports:

0x05, 0x01,         /*  Usage Page (Desktop),                   */
0x09, 0x05,         /*  Usage (Gamepad),                        */
0xA1, 0x01,         /*  Collection (Application),               */
0xA1, 0x02,         /*      Collection (Logical),               */
0x85, 0x01,         /*          Report ID (1),                  */
...

Reported-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: fix sleeping function warning from __put_anon_vma

commit 7f39dda9d86fb4f4f17af0de170decf125726f8c upstream.

Trinity reports BUG:

  sleeping function called from invalid context at kernel/locking/rwsem.c:47
  in_atomic(): 0, irqs_disabled(): 0, pid: 5787, name: trinity-c27

__might_sleep < down_write < __put_anon_vma < page_get_anon_vma <
migrate_pages < compact_zone < compact_zone_order < try_to_compact_pages ..

Right, since conversion to mutex then rwsem, we should not put_anon_vma()
from inside an rcu_read_lock()ed section: fix the two places that did so.
And add might_sleep() to anon_vma_free(), as suggested by Peter Zijlstra.

Fixes: 88c22088bf23 ("mm: optimize page_lock_anon_vma() fast-path")
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/memory-failure.c: don't let collect_procs() skip over processes for MF_ACTION_REQUIRED

commit 74614de17db6fb472370c426d4f934d8d616edf2 upstream.

When Linux sees an "action optional" machine check (where h/w has reported
an error that is not in the current execution path) we generally do not
want to signal a process, since most processes do not have a SIGBUS
handler - we'd just prematurely terminate the process for a problem that
they might never actually see.

task_early_kill() decides whether to consider a process - and it checks
whether this specific process has been marked for early signals with
"prctl", or if the system administrator has requested early signals for
all processes using /proc/sys/vm/memory_failure_early_kill.

But for MF_ACTION_REQUIRED case we must not defer.  The error is in the
execution path of the current thread so we must send the SIGBUS
immediatley.

Fix by passing a flag argument through collect_procs*() to
task_early_kill() so it knows whether we can defer or must take action.

Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Chen Gong <gong.chen@linux.jf.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/memory-failure.c-failure: send right signal code to correct thread

commit a70ffcac741d31a406c1d2b832ae43d658e7e1cf upstream.

When a thread in a multi-threaded application hits a machine check because
of an uncorrectable error in memory - we want to send the SIGBUS with
si.si_code = BUS_MCEERR_AR to that thread.  Currently we fail to do that
if the active thread is not the primary thread in the process.
collect_procs() just finds primary threads and this test:

if ((flags & MF_ACTION_REQUIRED) && t == current) {

will see that the thread we found isn't the current thread and so send a
si.si_code = BUS_MCEERR_AO to the primary (and nothing to the active
thread at this time).

We can fix this by checking whether "current" shares the same mm with the
process that collect_procs() said owned the page.  If so, we send the
SIGBUS to current (with code BUS_MCEERR_AR).

Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Otto Bruggeman <otto.g.bruggeman@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Chen Gong <gong.chen@linux.jf.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: vmscan: do not throttle based on pfmemalloc reserves if node has no ZONE_NORMAL

commit 675becce15f320337499bc1a9356260409a5ba29 upstream.

throttle_direct_reclaim() is meant to trigger during swap-over-network
during which the min watermark is treated as a pfmemalloc reserve.  It
throttes on the first node in the zonelist but this is flawed.

The user-visible impact is that a process running on CPU whose local
memory node has no ZONE_NORMAL will stall for prolonged periods of time,
possibly indefintely.  This is due to throttle_direct_reclaim thinking the
pfmemalloc reserves are depleted when in fact they don't exist on that
node.

On a NUMA machine running a 32-bit kernel (I know) allocation requests
from CPUs on node 1 would detect no pfmemalloc reserves and the process
gets throttled.  This patch adjusts throttling of direct reclaim to
throttle based on the first node in the zonelist that has a usable
ZONE_NORMAL or lower zone.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: option: fix runtime PM handling

commit acf47d4f9c39b1cba467aa9442fc2efe0b1da741 upstream.

Fix potential I/O while runtime suspended due to missing PM operations
in send_setup.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: EHCI: avoid BIOS handover on the HASEE E200

commit b0a50e92bda3c4aeb8017d4e6c6e92146ebd5c9b upstream.

Leandro Liptak reports that his HASEE E200 computer hangs when we ask
the BIOS to hand over control of the EHCI host controller.  This
definitely sounds like a bug in the BIOS, but at the moment there is
no way to fix it.

This patch works around the problem by avoiding the handoff whenever
the motherboard and BIOS version match those of Leandro's computer.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Leandro Liptak <leandroliptak@gmail.com>
Tested-by: Leandro Liptak <leandroliptak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP: replace checks for CONFIG_USB_GADGET_OMAP

commit 77c2f02edbeda9409a7cf3fd66233015820c213a upstream.

Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
apparently required that checks for CONFIG_USB_GADGET_OMAP would be
replaced with checks for CONFIG_USB_OMAP. Do so now for the remaining
checks for CONFIG_USB_GADGET_OMAP, even though these checks have
basically been broken since v3.1.

And, since we're touching this code, use the IS_ENABLED() macro, so
things will now (hopefully) also work if USB_OMAP is modular.

Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: clear stall when disabling endpoint

commit 687ef9817df7ed960d14575b9033dde3d04631fe upstream.

so it seems like DWC3 IP doesn't clear stalls
automatically when we disable an endpoint, because
of that, we _must_ make sure stalls are cleared
before clearing the proper bit in DALEPENA register.

Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: rename CONFIG_USB_GADGET_PXA25X

commit d30f2065d6da377cc76771aca5a9850cfca8723b upstream.

Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit
c0a39151a405 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.

Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbtest: add a timeout for scatter-gather tests

commit 32b36eeae6a859670d2939a7d6136cb5e9ed64f8 upstream.

In usbtest, tests 5 - 8 use the scatter-gather library in usbcore
without any sort of timeout.  If there's a problem in the gadget or
host controller being tested, the test can hang.

This patch adds a 10-second timeout to the tests, so that they will
fail gracefully with an ETIMEDOUT error instead of hanging.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Huang Rui <ray.huang@amd.com>
Tested-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: usbtest: fix unlink write error with pattern 1

commit e4d58f5dcb7d7be45df8def31881ebfae99c75da upstream.

TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected.  Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.

[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

applicom: dereferencing NULL on error path

commit 8bab797c6e5724a43b7666ad70860712365cdb71 upstream.

This is a static checker fix.  The "dev" variable is always NULL after
the while statement so we would be dereferencing a NULL pointer here.

Fixes: 819a3eba4233 ('[PATCH] applicom: fix error handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: tidspbridge: check for CONFIG_SND_OMAP_SOC_MCBSP

commit d3921a03a89acb1b9ca599590c0131c89f8737d8 upstream.

Commit d0f47ff17f29 ("ASoC: OMAP: Build config cleanup for McBSP")
removed the Kconfig symbol OMAP_MCBSP. It left two checks for
CONFIG_OMAP_MCBSP untouched.

Convert these to checks for CONFIG_SND_OMAP_SOC_MCBSP. That must be
correct, since that re-enables calls to functions that are all found in
sound/soc/omap/mcbsp.c. And that file is built only if
CONFIG_SND_OMAP_SOC_MCBSP is defined.

Fixes: d0f47ff17f29 ("ASoC: OMAP: Build config cleanup for McBSP")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

extcon: max8997: Fix NULL pointer exception on missing pdata

commit dfee4111febf3d9ef3a640b2cd6205c75f4e7e3d upstream.

Fix NULL pointer exception when platform data is not supplied. The
driver dereferenced pdata pointer where it could be NULL.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 810d601f07c
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cpsw: fix null dereference at probe

commit 6954cc1f238199e971ec905c5cc87120806ac981 upstream.

Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_iucv: wrong mapping of sent and confirmed skbs

commit f5738e2ef88070ef1372e6e718124d88e9abe4ac upstream.

When sending data through IUCV a MESSAGE COMPLETE interrupt
signals that sent data memory can be freed or reused again.
With commit f9c41a62bba3f3f7ef3541b2a025e3371bcbba97
"af_iucv: fix recvmsg by replacing skb_pull() function" the
MESSAGE COMPLETE callback iucv_callback_txdone() identifies
the wrong skb as being confirmed, which leads to data corruption.
This patch fixes the skb mapping logic in iucv_callback_txdone().

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: peak_pci: prevent use after free at netdev removal

commit 0b5a958cf4df3a5cd578b861471e62138f55c85e upstream.

As remarked by Christopher R. Baker in his post at

http://marc.info/?l=linux-can&m=139707295706465&w=2

there's a possibility for an use after free condition at device removal.

This simplified patch introduces an additional variable to prevent the issue.
Thanks for catching this.

Reported-by: Christopher R. Baker <cbaker@rec.ri.cmu.edu>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.10.45

ALSA: control: Make sure that id->index does not overflow

commit 883a1d49f0d77d30012f114b2e19fc141beb3e8e upstream.

The ALSA control code expects that the range of assigned indices to a control is
continuous and does not overflow. Currently there are no checks to enforce this.
If a control with a overflowing index range is created that control becomes
effectively inaccessible and unremovable since snd_ctl_find_id() will not be
able to find it. This patch adds a check that makes sure that controls with a
overflowing index range can not be created.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: control: Handle numid overflow

commit ac902c112d90a89e59916f751c2745f4dbdbb4bd upstream.

Each control gets automatically assigned its numids when the control is created.
The allocation is done by incrementing the numid by the amount of allocated
numids per allocation. This means that excessive creation and destruction of
controls (e.g. via SNDRV_CTL_IOCTL_ELEM_ADD/REMOVE) can cause the id to
eventually overflow. Currently when this happens for the control that caused the
overflow kctl->id.numid + kctl->count will also over flow causing it to be
smaller than kctl->id.numid. Most of the code assumes that this is something
that can not happen, so we need to make sure that it won't happen

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: control: Don't access controls outside of protected regions

commit fd9f26e4eca5d08a27d12c0933fceef76ed9663d upstream.

A control that is visible on the card->controls list can be freed at any time.
This means we must not access any of its memory while not holding the
controls_rw_lock. Otherwise we risk a use after free access.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>