sd: Make discard granularity match logical block size when LBPRZ=1

A device may report an OPTIMAL UNMAP GRANULARITY and UNMAP GRANULARITY
ALIGNMENT in the Block Limits VPD. These parameters describe the
device's internal provisioning allocation units. By default the block
layer will round and align any discard requests based on these limits.

If a device reports LBPRZ=1 to guarantee zeroes after discard, however,
it is imperative that the block layer does not leave out any parts of
the requested block range. Otherwise the device can not do the required
zeroing of any partial allocation units and this can lead to data
corruption.

Since the dm thinp personality relies on the block layer's current
behavior and is unable to deal with partial discard blocks we work
around the problem by setting the granularity to match the logical block
size when LBPRZ is enabled.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: select CONFIG_SCSI_SAS_ATTR

The hpsa driver recently started using the sas transport class, but it
does not ensure that the corresponding code is actually built, which
may lead to a link error:

drivers/built-in.o: In function `hpsa_free_sas_phy':
(.text+0x1ce874): undefined reference to `sas_port_delete_phy'
(.text+0x1ce87c): undefined reference to `sas_phy_free'
drivers/built-in.o: In function `hpsa_alloc_sas_port':
(.text+0x1ceb9c): undefined reference to `sas_port_alloc_num'
(.text+0x1ceba8): undefined reference to `sas_port_add'
drivers/built-in.o: In function `hpsa_init':
(.init.text+0x8838): undefined reference to `sas_attach_transport'
(.init.text+0x8868): undefined reference to `sas_release_transport

This adds 'select SCSI_SAS_ATTR' in the Kconfig entry, just like we do
for all other drivers using those functions.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d04e62b9d63a ("hpsa: add in sas transport class")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: advansys needs ISA dma api for ISA support

The advansys drvier uses the request_dma function that is used on ISA
machines for the internal DMA controller, which causes build errors
on platforms that have ISA slots but do not provide the ISA DMA API:

drivers/scsi/advansys.c: In function 'advansys_board_found':
drivers/scsi/advansys.c:11300:10: error: implicit declaration of function 'request_dma' [-Werror=implicit-function-declaration]

The problem now showed up in ARM randconfig builds after commit
6571fb3f8b7f ("advansys: Update to version 3.5 and remove compilation
warning") made it possible to build on platforms that have neither
VIRT_TO_BUS nor ISA_DMA_API but that do have ISA.

This adds the missing dependency.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_sysfs: protect against double execution of __scsi_remove_device()

On some host errors storvsc module tries to remove sdev by scheduling a job
which does the following:

   sdev = scsi_device_lookup(wrk->host, 0, 0, wrk->lun);
   if (sdev) {
       scsi_remove_device(sdev);
       scsi_device_put(sdev);
   }

While this code seems correct the following crash is observed:

 general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
 RIP: 0010:[<ffffffff81169979>]  [<ffffffff81169979>] bdi_destroy+0x39/0x220
 ...
 [<ffffffff814aecdc>] ? _raw_spin_unlock_irq+0x2c/0x40
 [<ffffffff8127b7db>] blk_cleanup_queue+0x17b/0x270
 [<ffffffffa00b54c4>] __scsi_remove_device+0x54/0xd0 [scsi_mod]
 [<ffffffffa00b556b>] scsi_remove_device+0x2b/0x40 [scsi_mod]
 [<ffffffffa00ec47d>] storvsc_remove_lun+0x3d/0x60 [hv_storvsc]
 [<ffffffff81080791>] process_one_work+0x1b1/0x530
 ...

The problem comes with the fact that many such jobs (for the same device)
are being scheduled simultaneously. While scsi_remove_device() uses
shost->scan_mutex and scsi_device_lookup() will fail for a device in
SDEV_DEL state there is no protection against someone who did
scsi_device_lookup() before we actually entered __scsi_remove_device(). So
the whole scenario looks like that: two callers do simultaneous (or
preemption happens) calls to scsi_device_lookup() ant these calls succeed
for both of them, after that they try doing scsi_remove_device().
shost->scan_mutex only serializes their calls to __scsi_remove_device()
and we end up doing the cleanup path twice.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

st: fix potential null pointer dereference.

If cdev_add() returns an error, the code calls
cdev_del() passing the STm->cdevs[rew] pointer as parameter;
the problem is that the pointer has not been initialized yet.

This patch fixes the problem by moving the STm->cdevs[rew] pointer
initialization before the call to cdev_add().
It also sets STm->devs[rew] and STm->cdevs[rew] to NULL in
case of failure.

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: report 'INQUIRY result too short' once per host

Some host adapters (e.g. Hyper-V storvsc) are known for not respecting
the SPC-2/3/4 requirement for 'INQUIRY data (see table ...) shall
contain at least 36 bytes'. As a result we get tons on 'scsi 0:7:1:1:
scsi scan: INQUIRY result too short (5), using 36' messages on
console. This can be problematic for slow consoles. Introduce
short_inquiry flag in struct Scsi_Host to print the message once per
host.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

advansys: fix big-endian builds

Building the advansys driver in a big-endian configuration such as
ARM allmodconfig shows a warning:

 drivers/scsi/advansys.c: In function 'adv_build_req':
 include/uapi/linux/byteorder/big_endian.h:32:26: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  #define __cpu_to_le32(x) ((__force __le32)__swab32((x)))
 drivers/scsi/advansys.c:7806:22: note: in expansion of macro 'cpu_to_le32'
   scsiqp->sense_len = cpu_to_le32(SCSI_SENSE_BUFFERSIZE);

It turns out that the commit that introduced this used the cpu_to_le32()
incorrectly on an 8-bit field, which results in the sense_len to always
be set to zero, as the SCSI_SENSE_BUFFERSIZE value gets moved to upper
byte of the 32-bit intermediate.

This removes the cpu_to_le32() call to restore the original version.

I found this only by looking at the compiler output and have not done a
full review for possible further endianess bugs in the same driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 811ddc057aac ("advansys: use DMA-API for mapping sense buffer")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Fix rwlock recursion

This patch fixes the following kernel bug:

kernel:BUG: rwlock recursion on CPU#2, insmod/39333, ffff8803e998cb28
kernel: Call Trace:
kernel: [<ffffffff812bce44>] dump_stack+0x48/0x64
kernel: [<ffffffff810a8047>] rwlock_bug+0x67/0x70
kernel: [<ffffffff810a833a>] do_raw_write_lock+0x8a/0xa0
kernel: [<ffffffff815f3033>] _raw_write_lock_irqsave+0x63/0x80
kernel: [<ffffffffa08087c8>] qla82xx_rd_32+0xe8/0x140 [qla2xxx]
kernel: [<ffffffffa0808845>] qla82xx_crb_win_lock+0x25/0x60 [qla2xxx]
kernel: [<ffffffffa0808976>] qla82xx_wr_32+0xf6/0x150 [qla2xxx]
kernel: [<ffffffffa0808ac0>] qla82xx_disable_intrs+0x50/0x80 [qla2xxx]
kernel: [<ffffffffa080630a>] qla82xx_reset_chip+0x1a/0x20 [qla2xxx]
kernel: [<ffffffffa07d6ef2>] qla2x00_initialize_adapter+0x132/0x420 [qla2xxx]
kernel: [<ffffffffa08087c8>] qla82xx_rd_32+0xe8/0x140 [qla2xxx]
kernel: [<ffffffffa0808845>] qla82xx_crb_win_lock+0x25/0x60 [qla2xxx]
kernel: [<ffffffffa0808976>] qla82xx_wr_32+0xf6/0x150 [qla2xxx]
kernel: [<ffffffffa0808ac0>] qla82xx_disable_intrs+0x50/0x80 [qla2xxx]
kernel: [<ffffffffa080630a>] qla82xx_reset_chip+0x1a/0x20 [qla2xxx]
kernel: [<ffffffffa07d6ef2>] qla2x00_initialize_adapter+0x132/0x420 [qla2xxx]
kernel: [<ffffffffa07c964e>] qla2x00_probe_one+0xefe/0x2130 [qla2xxx]
kernel: [<ffffffff8130052c>] local_pci_probe+0x4c/0xa0
kernel: [<ffffffff81300603>] pci_call_probe+0x83/0xa0
kernel: [<ffffffff813008cf>] pci_device_probe+0x7f/0xb0
kernel: [<ffffffff813e2e83>] really_probe+0x133/0x390
kernel: [<ffffffff813e3139>] driver_probe_device+0x59/0xd0
kernel: [<ffffffff813e3251>] __driver_attach+0xa1/0xb0
kernel: [<ffffffff813e0cdd>] bus_for_each_dev+0x8d/0xb0
kernel: [<ffffffff813e28ee>] driver_attach+0x1e/0x20
kernel: [<ffffffff813e2252>] bus_add_driver+0x1d2/0x290
kernel: [<ffffffff813e3970>] driver_register+0x60/0xe0
kernel: [<ffffffff813009e4>] __pci_register_driver+0x64/0x70
kernel: [<ffffffffa04bc1cb>] qla2x00_module_init+0x1cb/0x21b [qla2xxx]
kernel: [<ffffffff8100027d>] do_one_initcall+0xad/0x1c0
kernel: [<ffffffff810e2859>] do_init_module+0x69/0x210
kernel: [<ffffffff810e4e5c>] load_module+0x5cc/0x750
kernel: [<ffffffff810e5162>] SyS_init_module+0x92/0xc0
kernel: [<ffffffff815f37d7>] entry_SYSCALL_64_fastpath+0x12/0x6f

Fixes: 8dfa4b5a9b44 ("qla2xxx: Fix sparse annotation")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Xose Vazquez Perez <xose.vazquez@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.3+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: logical vs bitwise AND typo

HPSA_DIAG_OPTS_DISABLE_RLD_CACHING is a mask and bitwise AND was
intended here instead of logical &&.  This bug is essentially harmless,
it means that sometimes we don't print a warning message which we wanted
to print.

Fixes: c2adae44e916 ('hpsa: disable report lun data caching')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mvsas: don't allow negative timeouts

There is a static checker warning here because "val" is controlled by
the user and we have a upper bound on it but allow negative numbers.
"val" appears to be a timeout in usec so this bug probably means we
have a longer timeout than we should.  Let's fix this by changing "val"
to unsigned.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag

Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.

Actually in the driver code, driver is using below API's

1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.

but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

sd: Clear PS bit before Mode Select.

According to SPC-4, in a Mode Select, the PS bit in Mode Pages is
reserved and must be set to 0 by the driver.  In the sd implementation,
function cache_type_store does a Mode Sense, which might set the PS bit
on the read buffer, followed by a Mode Select, which receives the same
buffer, without explicitly clearing the PS bit.  So, in cases where
target supports saving the Mode Page to a non-volatile location, we end
up doing a Mode Select with the PS bit set, which could cause an illegal
request error if the target is checking this.

This was observed on a new firmware change, which was subsequently
reverted, but this changes sd.c to be more compliant with SPC-4.

This patch clears the PS bit in the buffer returned by Mode Select,
right before it is used in the Mode Select command.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ibmvscsi: set max_lun to 32

As defined in 4.6.9 of SAM-4, the encoding of LUN is
on 5 bits (max_lun=32) and the current value is only 8.
Set max_lun to IBMVSCSI_MAX_LUN (32).

Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ibmvscsi: display default value for max_id, max_lun and max_channel.

As devices with values greater than that are silently ignored,
this gives some hints to the sys admin to know why he doesn't see
his devices...

Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()

There is a static checker warning here because "bytes" is controlled by
the user and we cap the upper bound with min() but allow negatives.
Negative bytes will result in some nasty warning messages but are not
super harmful.  Anyway, no one needs negative bytes so let's just check
for it and return NULL.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()

Replace the use of struct timeval and do_gettimeofday() with
64 bit ktime_get_real_seconds. Prevents 32-bit type overflow
in year 2038 on 32-bit systems.

Driver was using the seconds portion of struct timeval (.tv_secs)
to pass a millseconds timestamp to the firmware. This change maintains
that same behavior using ktime_get_real_seconds.

The structure used to pass the timestamp to firmware is 48 bits and
works fine as long as the top 16 bits are zero and they will be zero
for a long time..ie. thousands of years.

Alternative Change:  Add sub second granularity to timestamp

As noted above, the driver only used the seconds portion of timeval,
ignores the microseconds portion, and by multiplying by 1000 effectively
does a <<10 and always writes zero into timestamp[0].

The alternative change would pass all the bits to the firmware:

        struct timespec64 ts;

        ktime_get_real_ts64(&ts);
        timestamp = ts.tv_sec * MSEC_PER_SEC + ts.tv_nsec / NSEC_PER_MSEC;

Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mvumi: 64bit value for seconds_since1970

struct mvumi_hs_page2 stores a "seconds_since1970" field which is of
type u64. It is however, written to, using 'struct timeval' which has
a 32-bit seconds field and whose value will overflow in year 2038.
This patch uses ktime_get_real_seconds() instead since it provides a
64-bit seconds value, which is 2038 safe.

Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

be2iscsi: Fix bogus WARN_ON length check

drivers/scsi/be2iscsi/be_main.c: In function 'be_sgl_create_contiguous':
drivers/scsi/be2iscsi/be_main.c:3187:18: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
  WARN_ON(!length > 0);

gcc version 5.2.1

Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com>
Cc: Minh Tran <minh.tran@avagotech.com>
Cc: John Soni Jose <sony.john-n@avagotech.com>
Cc: "James E.J. Bottomley" <JBottomley@odin.com>
Reported-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice

The only user of scsi_prep_async_scan() is scsi_scan_host() and it
handles the situation correctly. Move 'called twice' reporting to debug
level as well.

The issue is observed on Hyper-V: on any device add/remove event storvsc
driver calls scsi_scan_host() and in case previous scan is still running
we get the message and stack dump on console.

Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Bump mpt3sas driver version to 09.102.00.00

Bump mpt3sas driver version to 09.102.00.00

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs

Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.

* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.

* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
  that, during the driver load time driver can use corresponding host
  template(based the pci device ID) while registering a scsi host
  adapter instance for that pci device.

* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
  SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
  processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
  device processes only those ioctl cmds issued for the SAS3 HBAs.

* Added separate indexing for SAS2 and SAS3 HBAs.

* Replaced compile time check 'MPT2SAS_SCSI' to run time check
  'hba_mpi_version_belonged' whereever needed.

* Aliased this merged driver to mpt2sas using MODULE_ALIAS.

* Moved global varaible 'driver_name' to per adapter instance variable.

* Created two raid function template and used corresponding raid
  function templates based on the run time check
  'hba_mpi_version_belonged'.

* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
  renamed it as mpt3sas_warpdrive.c.

* Also renamed the functions in mpt3sas_warpdrive.c file to follow
  current driver function name convention.

* Updated the Makefile to build mpt3sas_warpdrive.o file for these
  WarpDrive-specific functions.

* Also in function mpt3sas_setup_direct_io(), used sector_div() API
  instead of division operator (which gives compilation errors on 32 bit
  machines).

* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.

* Added module parameter 'hbas_to_enumerate' which permits using this
  merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
  driver.

  Here are the available options for this module parameter:

   0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
   1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
   2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs

* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt2sas, mpt3sas: Update the driver versions

Bump the mpt2sas driver version to 20.102.00.00 and
Bump the mpt3sas driver version to 9.101.00.00.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: setpci reset kernel oops fix

setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops

1. pci_access_mutex lock added to provide synchronization between IOCTL,
   sysfs, PCI resource handling path

2. gioc_lock spinlock to protect list operations over multiple
   controllers

This patch is ported from commit 6229b414b3ad ("mpt2sas: setpci reset
kernel oops fix").

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Added OEM Gen2 PnP ID branding names

Added OEM Gen2 PnP ID branding names from mpt2sas driver.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Refcount fw_events and fix unsafe list usage

The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.

Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.

This patch is ported from commit 008549f6e8a1 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Refcount sas_device objects and fix unsafe list usage

sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.

Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.

This patch is ported from the following mpt2sas driver commit
d224fe0d6097 ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: sysfs attribute to report Backup Rail Monitor Status

A new sysfs shost attribute called "BMR_status" is implemented to report
Backup Rail Monitor status.

This attribute is located in:

        /sys/class/scsi_host/host#/BMR_status

When reading this adapter attribute, the driver will output the state of
GPIO[24]. It returns "0" if BMR is healthy and "1" for failure.

If it returns an empty string then it means that there was an error
while obtaining the BMR status. Check dmesg for what error has occurred.

This sysfs shost attribute is mainly for WarpDrive controllers.

This commit is a port of 6c265660c262 ("mpt2sas: Provide sysfs attribute
to report Backup Rail Monitor Status").

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Ported WarpDrive product SSS6200 support

Ported the following list of WarpDrive-specific patches:

1. commit 0bdccdb0a090ad8dc5f851cad5e843244c410ee8 ("mpt2sas: WarpDrive
   New product SSS6200 support added")

2. commit 82a452581230b3ffc9d6475dffdb2568497b5fec ("mpt2sas: WarpDrive
   Infinite command retries due to wrong scsi command entry in MPI
   message")

3. commit ba96bd0b1d4a4e11f23671e1f375a5c8f46b0fe7 ("mpt2sas: Support
   for greater than 2TB capacity WarpDrive")

4. commit 4da7af9494b2f98a1503a2634059300c3e4615e6 ("mpt2sas: Do not
   retry a timed out direct IO for Warpdrive")

5. commit daeaa9df92bd742f4e6d4d6039d689277a8e31bd ("mpt2sas: Avoid type
   casting for direct I/O commands").

Also set the mpt2_ioctl_iocinfo adapter_type to:

1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs

2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive

3. MPT2_IOCTL_INTERFACE_SAS2  for other Gen2 HBAs

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: fix for driver fails EEH, recovery from injected pci bus error

This patch stops the driver to invoke kthread (which remove the dead
ioc) for some time while EEH recovery has started.

This patch is a port of commit b4730fb6e54a ("mpt2sas: fix for driver
fails EEH, recovery from injected pci bus error")'.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Manage MSI-X vectors according to HBA device type

1. Do not enable MSI-X vectors for SAS2008 B0 controllers

2. Enable a single MSI-X vector for the following controller:

   a. SAS2004
   b. SAS2008
   c. SAS2008_1
   d. SAS2008_2
   e. SAS2008_3
   f. SAS2116_1
   g. SAS2116_2

3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for Gen3 Invader/Fury C0 and above revision HBAs

4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for all Intruder and Cutlass HBAs

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Don't send PHYDISK_HIDDEN RAID action request on SAS2 HBAs

Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.

Also enable fast_path only for SAS3 HBAs.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs

Gen2 HBAs use MPI scatter-gather lists whereas Gen3 HBAs use IEEE
scatter-gather lists. Modify the common code part in such a way that it
will build IEEE SGL tables for Gen3 HBAs and MPI SGL tables for Gen2
HBAs.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt2sas, mpt3sas: Remove SCSI_MPTXSAS_LOGGING entry from Kconfig

Currently there is a logging level option provided for each of our
drivers in the kernel configuration utility. Users can enable this
option to get more verbose information. By default it is enabled.

Only when this option is enabled will the functions which display the
required information get compiled in.

As we are merging the both drivers we can no longer provide this
configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig
and unconditionally enable logging (by removing the #ifdef
CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all
functions which are defined to display more verbose information get
compiled in.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Define 'hba_mpi_version_belonged' IOC variable

1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.

2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt2sas: Remove .c and .h files from mpt2sas driver

Remove .c and .h files which are no longer needed from mpt2sas
driver. We are reusing this code from mpt3sas.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt2sas: Move Gen2 HBA's device registration to a separate file

1. Create a mpt2sas_module.c file for mpt2sas where GEN2 HBA devices
register with PCI, SML, IOCTL subsystems.

2. Updated the Makefile to use the object files from mpt3sas folder.

3. Defined a compilation flag SCSI_MPT2SAS which can be used to not
include those sections of code from mpt3sas driver which are not
required for mpt2sas driver.

4. Inherited automatic diag buffer feature from mpt3sas driver.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Move Gen3 HBA's device registration to a separate file

Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Added mpt2sas driver definitions

1. Added mpt2sas driver related macros in mpt3sas header files

2. Made scsi host's, raid class', pci's, ioctl's callback functions
global so that both drivers can use them.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt2sas: Use mpi headers from mpt3sas

Use a single set of the hardware description headers instead of having
them in the source tree twice.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: remove the SCSI host before detaching from SAS transport

Previously, when this module was unloaded via 'rmmod' with at least one
drive attached, the SCSI error handler thread would become stuck in an
infinite recovery loop and lockup the system, necessitating a reboot.

Once the SAS layer is detached, the driver will fail any subsequent
commands since the target devices are removed.  However, removing the
SCSI host generates a SYNCHRONIZE CACHE (10) command, which was failed
and left the error handler no method of recovery.

This patch simply removes the SCSI host first so that no more commands
can come down, prior to cleaning up the SAS layer.  Note that the stack
is built up with the SCSI host first, and then the SAS layer.  Perhaps
it should be reversed for symmetry, so that commands cannot be sent to
the pm80xx driver prior to attaching the SAS layer?

What was really strange about this bug was that it was introduced at
commit cff549e4860f ("[SCSI]: proper state checking and module refcount
handling in scsi_device_get").  This commit appears to tinker with how
the reference counting is performed for SCSI device objects.  My theory
is that prior to this commit, the refcount for a device object was
blindly incremented at some point during the teardown process which
coincidentially made the device stick around during the procedure, which
also coincidentially made any commands sent to the driver not fail
(since the device was technically still "there").  After this commit was
applied, my theory is the refcount for the device object is not being
incremented at a specific point anymore, which makes the device go away,
and thus made the pm80xx driver fail any subsequent commands.

You may also want to see the following for more details:

[1] http://www.spinics.net/lists/linux-scsi/msg37208.html
[2] http://marc.info/?l=linux-scsi&m=144416476406993&w=2

Signed-off-by: Benjamin Rood <brood@attotech.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mvsas: remove SCSI host before detaching from SAS transport

commit cff549e4860f ("scsi: proper state checking and module refcount
handling in scsi_device_get") the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.

Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.

This is a follow up fix for Benjamin's fix for pm80xx.

See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html

Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aic94xx: remove SCSI host before detaching from SAS transport

commit cff549e4860f ("scsi: proper state checking and module refcount
handling in scsi_device_get") the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.

Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.

This is a follow up fix for Benjamin's fix for pm80xx.

See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html

Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

isci: remove SCSI host before detaching from SAS transport

commit cff549e4860f ("scsi: proper state checking and module refcount
handling in scsi_device_get") , the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.

Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.

This is a follow up fix for Benjamin's fix for pm80xx.

See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html

Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Driver version 2.6.3.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Issue Configure Cache Parameters command.

Some new adapters require a special Configure Cache Parameters command
to enable the adapter write cache, so send this during the adapter
initialization if the adapter requires it.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Inquiry IOA page 0xC4 during initialization.

Add an IOA Inquiry command for Page 0xC4 during IOA initialization to
collect cache capabilities, particularly to check if Sync IOA Write
Cache is supported.

Inquiry will happen right after Cap Inquiry on page 0xD0; and will
execute only if the "Supported Pages" field in Inquiry Page 0x0 shows
support for Page 0xC4.  Otherwise, assume Sync IOA Write Cache is
not supported.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Don't set NO_ULEN_CHK bit when resource is a vset.

According to the IPR specification, Inhibit Underlength Checking bit
must be disabled when issuing commands to vsets.  Enabling it in this
case might cause SCSI commands to fail with an Illegal Request, so make
sure we keep this bit cleared when resource is a vset.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Add delay to ensure coherent dumps.

Add a holding pattern prior to collecting dump data, to wait for the IOA
indication that the Mailbox register is stable and won't change without
an explicit reset.  This ensures we'll be collecting meaningful dump
data, even when dumping right after an adapter reset.

In the event of a timeout, we still force the dump, since a partial dump
still might be useful.

Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: add QUniPro hardware support and power optimizations

New revisions of UFS host controller supports the new UniPro
hardware controller (referred as QUniPro). This patch adds
the support to enable this new UniPro controller hardware.

This change also adds power optimization for bus scaling feature,
as well as support for HS-G3 power mode.

Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: add debug prints for test bus

Adds support for configuring and reading the test bus and debug
registers. This change also adds another vops in order to print the
debug registers.

Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: make the UFS variant a platform device

This change turns the UFS variant (SCSI_UFS_QCOM) into a UFS
a platform device.
In order to do so a few additional changes are required:
1. The ufshcd-pltfrm is no longer serves as a platform device.
   Now it only serves as a group of platform APIs such as PM APIs
   (runtime suspend/resume, system suspend/resume etc), parsers of
   clocks, regulators and pm_levels from DT.
2. What used to be the old platform "probe" is now "only"
   a pltfrm_init() routine, that does exactly the same, but only
   being called by the new probe function of the UFS variant.

Reviewed-by: Rob Herring <robherring2@gmail.com>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: creates wrapper functions for vops

In order to simplify the code a set of wrapper functions is created
to test and call each of the variant operations.

Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: add ufshcd_get_variant ufshcd_set_variant

This patch adds ufshcd_get_variant() and ufshcd_set_variant()
routines in order to get/set the variant specific data.

Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: update configuration option of SCSI_UFS_QCOM component

This change is required in order to be able to build the component
as a module.

Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: fix compilation warning if compiled as a module

This change fixes a compilation warning that happens if SCSI_UFS_QCOM is
compiled as a module.  Also this patch fixes an error happens when
insmod the module: "ufs_qcom: module license 'unspecified' taints
kernel."

Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

phy: qcom-ufs: fix build error when the component is built as a module

Export the following functions in order to avoid build errors
when the component PHY_QCOM_UFS is compiled as a module:

ERROR: "ufs_qcom_phy_disable_ref_clk"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_enable_ref_clk"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_is_pcs_ready"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_disable_iface_clk"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_start_serdes"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_calibrate_phy"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_enable_dev_ref_clk"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_set_tx_lane_enable"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_disable_dev_ref_clk"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_save_controller_version"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
ERROR: "ufs_qcom_phy_enable_iface_clk"
[drivers/scsi/ufs/ufs-qcom.ko] undefined!
make[1]: *** [__modpost] Error 1

Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: move lockup_detected attribute to host attr

This patch fixes a 'general protection fault' issue by
moving the attribute to where it was likely meant.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: bump the driver version

Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Gerry Morong <gerry.morong.pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: add in sas transport class

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix multiple issues in path_info_show

path_info_show() seems to be broken in multiple ways.

First, there's

  817 return snprintf(buf, output_len+1, "%s%s%s%s%s%s%s%s",
  818       path[0], path[1], path[2], path[3],
  819       path[4], path[5], path[6], path[7]);

so hopefully output_len contains the combined length of the eight
strings. Otherwise, snprintf will stop copying to the output
buffer, but still end up reporting that combined length - which
in turn would result in user-space getting a bunch of useless nul
bytes (thankfully the upper sysfs layer seems to clear the output
buffer before passing it to the various ->show routines). But we have

  767      output_len = snprintf(path[i],
  768                       PATH_STRING_LEN, "[%d:%d:%d:%d] %20.20s ",
  769                       h->scsi_host->host_no,
  770                       hdev->bus, hdev->target, hdev->lun,
  771                       scsi_device_type(hdev->devtype));

so output_len at best contains the length of the last string printed.

Inside the loop, we then otherwise add to output_len. By magic,
we still have PATH_STRING_LEN available every time... This
wouldn't really be a problem if the bean-counting has been done
properly and each line actually does fit in 50 bytes, and maybe
it does, but I don't immediately see why. Suppose we end up
taking this branch:

  802                  output_len += snprintf(path[i] + output_len,
  803                          PATH_STRING_LEN,
  804                          "BOX: %hhu BAY: %hhu %s\n",
  805                          box, bay, active);

An optimistic estimate says this uses strlen("BOX: 1 BAY: 2
Active\n") which is 21. Now add the 20 bytes guaranteed by the
%20.20s and then some for the rest of that format string, and
we're easily over 50 bytes. I don't think we can get over 100
bytes even being pessimistic, so this just means we'll scribble
into the next path[i+1] and maybe get that overwritten later,
leading to some garbled output (in fact, since we'd overwrite the
previous string's 0-terminator, we could end up with one very
long string and then print various suffixes of that, leading to
much more than 400 bytes of output). Except of course when we're
filling path[7], where overrunning it means writing random stuff
to the kernel stack, which is usually a lot of fun.

We can fix all of that and get rid of the 400 byte stack buffer by
simply writing directly to the given output buffer, which the upper
layer guarantees is at least PAGE_SIZE. s[c]nprintf doesn't care where
it is writing to, so this doesn't make the spin lock hold time any
longer. Using scnprintf ensures that output_len always represents the
number of bytes actually written to the buffer, so we'll report the
proper amount to the upper layer.

Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: enhance device messages

Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: disable report lun data caching

When external target arrays are present, disable the firmware's
normal behavior of returning a cached copy of the report lun data,
and force it to collect new data each time we request a report luns.

This is necessary for external arrays, since there may be no
reliable signal from the external array to the smart array when
lun configuration changes, and thus when driver requests
report luns, it may be stale data.

Use diag options to turn off RPL data caching.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: add discovery polling for PT RAID devices.

There are problems with getting configuration change notification
in pass-through RAID environments.  So, activate flag
h->discovery_polling when one of these devices is detected in
update_scsi_devices.

After discovery_polling is set, execute a report luns from
rescan_controller_worker (every 30 seconds).

If the data from report_luns is different than last
time (binary compare), execute a full rescan via update_scsi_devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: eliminate fake lun0 enclosures

We don't need to create fake enclosure devices at Lun0
in external target array configurations anymore.
This was done to support Pre-SCSI rev 5 controllers
that didn't suppoprt report luns commands, so the
SCSI layer had to scan targets. If there was no
LUN at LUN 0, then the target scan would stop, and
move to the next target.  Lun0 enclosure device
was added to prevent sparsely-numbered LUNs from
being missed.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: generalize external arrays

External array LUNs must use target and lun numbers assigned by the
external array. So the driver must treat these differently from
local LUNs when assigning lun/target.

LUN's 'model' field has been used to detect Lun types that need
special treatment, but the desire is to eliminate the need to reference
specific array models, and support any external array.

Pass-through RAID (PTRAID) luns are not luns of the local controller,
so they are not reported in LUN count of command 'ID controller'.
However, they ARE reported in "Report logical Luns" command.
Local luns are listed first, then PTRAID LUNs.

The number of luns from "Report LUNs" in excess of those reported by
'ID controller' are therefore the PTRAID LUNS.

We can now remove function is_ext_target, and the 'white list'
array of supported model names.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: move scsi_add_device and scsi_remove_device calls to new function

preparation for adding the sas transport class

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: refactor hpsa_figure_bus_target_lun

setup for sas transport. Need to set the
bus and target accordingly.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: enhance hpsa_get_device_id

use an index into vpd data for SAS/SATA drives

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: add function is_logical_device

simplify checking for logical/physical devices

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: simplify update scsi devices

remove repeated calculation that checks for physical
or logical devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: simplify check for device exposure

remove macros and cleanup device exposure checking

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: correct ioaccel2 sg chain len

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: correct check for non-disk devices

The driver is using two MACROs which seemingly are looking in
the wrong location for the device_flags returned from
CISS_REPORT_PHYS. Both MACROs, NON_DISK_PHYS_DEV and
PHYS_IOACCEL, are using the pointer returned from figure_lunaddrbytes
which is the address of the LUN.lunid element in
the extended CISS_REPORT_PHYS.  But the MACROS are using offsets
beyond the range of the element (offset 17 of an 8 byte element).

These MACROs actually are looking at the correct location but
they fail static checker analysis. It also will not work
if any new elements are added to the extended LUN structure.

Change the code to use the structure elements directly
since this MACRO is only used in one location.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix physical target reset

Set reset type in device_reset_handler to do either
logical unit reset for logical devices, or physical
target reset, for physical devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix hpsa_adjust_hpsa_scsi_table

Fix a NULL pointer issue in the driver when devices are removed
during a reset.

Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: correct transfer length for 6 byte read/write commands

handle block counts of 0. Cleanup block and block count calculations.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: abandon rescans on memory alloaction failures.

Abandon and reschedule rescan process only if device inquiries
fail due to mem alloc failures, which are likely to occur for
all devices.

Otherwise, skip device if inquiry fails for other reasons,
and continue rescanning process for other devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: allow driver requested rescans

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by; Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix null device issues

Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: check for null arguments to dev_printk

Check for NULLs.

Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: change devtype to unsigned

This member is used in calls to scsi_device_type.
It should be unsigned since the kernel checks for upper bounds
and it should never be negative.

Suggested-by: Tomas Henzl <thenzl@redhat.com>
Suggested-by: Hannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: remove unused hpsa_tag_discard_error_bits

This function is no longer used.

Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: stop zeroing reset_cmds_out and ioaccel_cmds_out during rescan

pulling the rug out from under the reset handler
likewise for ioaccel_cmds_out

Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: remove unused parameter hostno

This parameter was once used before scan_start was defined
but now it is no longer used.

Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_sysfs: Fix queue_ramp_up_period return code

Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.

Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: Export SCSI Inquiry data to sysfs

Export the RAW SCSI Inquiry to sysfs as binfile. This way the data can be used
by userland without the need to have and ioctl or use the sg_inq tool.

Here is an example of the provided data

linux:~ # hexdump /sys/class/scsi_device/1\:0\:0\:0/device/inquiry
0000000 8005 3205 001f 0000 4551 554d 2020 2020
0000010 4551 554d 4420 4456 522d 4d4f 2020 2020
0000020 2e32 2e33
0000024

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Fix sparse warning

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Make tape drives visible on PERC5 controllers

The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.

This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.

Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

sg: Fix double-free when drives detach during SG_IO

In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().

Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.

This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:

  ------------[ cut here ]------------
  kernel BUG at block/blk-core.c:1420!
  Call Trace:
  [<ffffffff81281eab>] blk_put_request+0x5b/0x80
  [<ffffffffa0069e5b>] sg_finish_rem_req+0x6b/0x120 [sg]
  [<ffffffffa006bcb9>] sg_common_write.isra.14+0x459/0x5a0 [sg]
  [<ffffffff8125b328>] ? selinux_file_alloc_security+0x48/0x70
  [<ffffffffa006bf95>] sg_new_write.isra.17+0x195/0x2d0 [sg]
  [<ffffffffa006cef4>] sg_ioctl+0x644/0xdb0 [sg]
  [<ffffffff81170f80>] do_vfs_ioctl+0x90/0x520
  [<ffffffff81258967>] ? file_has_perm+0x97/0xb0
  [<ffffffff811714a1>] SyS_ioctl+0x91/0xb0
  [<ffffffff81602afb>] tracesys+0xdd/0xe2
    RIP [<ffffffff81281e04>] __blk_put_request+0x154/0x1a0

The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.

Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.

KASAN was extremely helpful in finding the root cause of this bug.

Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: avoid a panic if MSI(X) interrupts are disabled

If MSI(X) interrupts are disabled via the kernel command line
(pci=nomsi), the pm8001 driver will kernel panic because it does not
detect that MSI interrupts are disabled and will soldier on and attempt to
configure MSI interrupts anyways.  This leads to a kernel panic, most
likely because a required data structure is not available down the
line.  Using the pci_msi_enabled() function in order to detect if MSI
interrupts are enabled before configuring them resolves this issue and
avoids a kernel panic when the module is loaded.  Additionally, the
irq_vector structure must be initialized when legacy interrupts are
being used otherwise legacy interrupts will simply not function and
result in another panic.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: wait a minimum of 500ms before issuing commands to SPCv

The documentation for the 8070 and 8072 SPCv chip explicitly states that
a minimum of 500ms must elapse before issuing commands, otherwise the
SPCv may not process them and the firmware may get into an unrecoverable
state requiring a reboot.  While the Linux guys will probably think this
is 'racy', it is called out in the chip documentation and inserting this
delay makes power management function properly.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: do not examine registers for iButton feature if ATTO adapter

ATTO adapters do not support this feature.  If the firmware fails to be
ready, it should not check the examined registers in order to examine
the state of the feature in order to prevent undefined behavior.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: set PHY profiles for ATTO 12Gb SAS controllers

PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set.  This patch
provides the necessary functionality to do so.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: add support for ATTO devices during SAS address initiailization

ATTO SAS controllers retrieve the SAS address from the NVRAM in a location
different from non-ATTO PMC Sierra SAS controllers.  This patch makes the
necessary adjustments in order to retrieve the SAS address on these types
of adapters.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: add ATTO PCI IDs to pm8001_pci_table

These PCI IDs allow the pm8001 driver to load against ATTO 12Gb SAS
controllers that use PMC Sierra 8070 and PMC Sierra 8072 SAS chips.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: add support for PMC Sierra 8070 and PMC Sierra 8072 SAS controllers

These SAS controllers support speeds up to 12Gb.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: configure PHY settings based on subsystem vendor ID

Previuosly, all PMC Sierra 80xx controllers are assumed to be a
motherboard controller, except if the subsystem vendor ID was equal to
PCI_VENDOR_ID_ADAPTEC.  The driver then attempts to load PHY settings
from NVRAM.  While this may be correct behavior for most controllers, it
does not work with Adaptec and ATTO controllers since they do not store
PHY settings in NVRAM and choose to use either custom PHY settings or
chip defaults.  Loading random values from NVRAM may cause the
controllers to malfunction in this edge case.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

SCSI: Increase REPORT_LUNS timeout

This patch fixes an issue seen with an IBM 2145 (SVC) where, following an error
injection test which results in paths going offline, when they came
back online, the path would timeout the REPORT_LUNS issued during the
scan. This timeout situation continued until retries were expired, resulting in
falling back to a sequential LUN scan. Then, since the target responds
with PQ=1, PDT=0 for all possible LUNs, due to the way the sequential
LUN scan code works, we end up adding 512 LUNs for each target, when there
is really only a small handful of LUNs that are actually present.

This patch increases the timeout used on the REPORT_LUNS to 30 seconds.
This patch solves the issue of 512 non existent LUNs showing up after
this event.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas : Remove debug print from function megasas_update_span_set

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas : Driver version upgrade

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>