Dave Hansen [Sun, 7 Jun 2015 18:37:06 +0000 (11:37 -0700)]
x86/mpx: Rewrite the unmap code
The MPX code needs to clear out bounds tables for memory which
is no longer in use. We do this when a userspace mapping is
torn down (unmapped).
There are two modes:
1. An entire bounds table becomes unused, and can be freed
and its pointer removed from the bounds directory. This
happens either when a large mapping is torn down, or when
a small mapping is torn down and it is the last mapping
"covered" by a bounds table.
2. Only part of a bounds table becomes unused, in which case
we free the backing memory as if MADV_DONTNEED was called.
The old code was a spaghetti mess of "edge" bounds tables
where the edges were handled specially, even if we were
unmapping an entire one. Non-edge bounds tables are always
fully unmapped, but share a different code path from the edge
ones. The old code had a bug where it was unmapping too much
memory. I worked on fixing it for two days and gave up.
I didn't write the original code. I didn't particularly like
it, but it worked, so I left it. After my debug session, I
realized it was undebuggagle *and* buggy, so out it went.
I also wrote a new unmapping test program which uncovers bugs
pretty nicely.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183706.DCAEC67D@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:05 +0000 (11:37 -0700)]
x86/mpx: Support 32-bit binaries on 64-bit kernels
Right now, the kernel can only switch between 64-bit and 32-bit
binaries at compile time. This patch adds support for 32-bit
binaries on 64-bit kernels when we support ia32 emulation.
We essentially choose which set of table sizes to use when doing
arithmetic for the bounds table calculations.
This also uses a different approach for calculating the table
indexes than before. I think the new one makes it much more
clear what is going on, and allows us to share more code between
the 32-bit and 64-bit cases.
Based-on-patch-by: Qiaowei Ren <qiaowei.ren@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183705.E01F21E2@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:05 +0000 (11:37 -0700)]
x86/mpx: Use 32-bit-only cmpxchg() for 32-bit apps
user_atomic_cmpxchg_inatomic() actually looks at sizeof(*ptr) to
figure out how many bytes to copy. If we run it on a 64-bit
kernel with a 64-bit pointer, it will copy a 64-bit bounds
directory entry. That's fine, except when we have 32-bit
programs with 32-bit bounds directory entries and we only *want*
32-bits.
This patch breaks the cmpxchg() operation out in to its own
function and performs the 32-bit type swizzling in there.
Note, the "64-bit" version of this code _would_ work on a
32-bit-only kernel. The issue this patch addresses is only for
when the kernel's 'long' is mismatched from the size of the
bounds directory entry of the process we are working on.
The new helper modifies 'actual_old_val' or returns an error.
But gcc doesn't know this, so it warns about 'actual_old_val'
being unused. Shut it up with an uninitialized_var().
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183705.672B115E@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:04 +0000 (11:37 -0700)]
x86/mpx: Introduce new 'directory entry' to 'addr' helper function
Currently, to get from a bounds directory entry to the virtual
address of a bounds table, we simply mask off a few low bits.
However, the set of bits we mask off is different for 32-bit and
64-bit binaries.
This breaks the operation out in to a helper function and also
adds a temporary variable to store the result until we are
sure we are returning one.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183704.007686CE@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:04 +0000 (11:37 -0700)]
x86/mpx: Add temporary variable to reduce masking
When we allocate a bounds table, we call mmap(), then add a
"valid" bit to the value before storing it in to the bounds
directory.
If we fail along the way, we go and mask that valid bit
_back_ out. That seems a little silly, and this makes it
much more clear when we have a plain address versus an
actual table _entry_.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183704.3D69D5F4@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:04 +0000 (11:37 -0700)]
x86: Make is_64bit_mm() widely available
The uprobes code has a nice helper, is_64bit_mm(), that consults
both the runtime and compile-time flags for 32-bit support.
Instead of reinventing the wheel, pull it in to an x86 header so
we can use it for MPX.
I prefer passing the 'mm' around to test_thread_flag(TIF_IA32)
because it makes it explicit where the context is coming from.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183704.F0209999@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:04 +0000 (11:37 -0700)]
x86/mpx: Trace allocation of new bounds tables
Bounds tables are a significant consumer of memory. It is
important to know when they are being allocated. Add a trace
point to trace whenever an allocation occurs and also its
virtual address.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183704.EC23A93E@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:03 +0000 (11:37 -0700)]
x86/mpx: Trace the attempts to find bounds tables
There are two different events being traced here. They are
doing similar things so share a trace "EVENT_CLASS" and are
presented together.
1. Trace when MPX is zapping pages "mpx_unmap_zap":
When MPX can not free an entire bounds table, it will
instead try to zap unused parts of a bounds table to free
the backing memory. This decreases RSS (resident set
size) without decreasing the virtual space allocated
for bounds tables.
2. Trace attempts to find bounds tables "mpx_unmap_search":
This event traces any time we go looking to unmap a
bounds table for a given virtual address range. This is
useful to ensure that the kernel actually "tried" to free
a bounds table versus times it succeeded in finding one.
It might try and fail if it realized that a table was
shared with an adjacent VMA which is not being unmapped.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183703.B9D2468B@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:03 +0000 (11:37 -0700)]
x86/mpx: Trace entry to bounds exception paths
There are two basic things that can happen as the result of
a bounds exception (#BR):
1. We allocate a new bounds table
2. We pass up a bounds exception to userspace.
This patch adds a trace point for the case where we are
passing the exception up to userspace with a signal.
We are also explicit that we're printing out the inverse of
the 'upper' that we encounter. If you want to filter, for
instance, you need to ~ the value first. The reason we do
this is because of how 'upper' is stored in the bounds table.
If a pointer's range is:
0x1000 -> 0x2000
it is stored in the bounds table as (32-bits here for brevity):
lower: 0x00001000
upper: 0xffffdfff
That is so that an all 0's entry:
lower: 0x00000000
upper: 0x00000000
corresponds to the "init" bounds which store a *range* of:
0x00000000 -> 0xffffffff
That is, by far, the common case, and that lets us use the
zero page, or deduplicate the memory, etc... The 'upper'
stored in the table is gibberish to print by itself, so we
print ~upper to get the *actual*, logical, human-readable
value printed out.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183703.027BB9B0@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:03 +0000 (11:37 -0700)]
x86/mpx: Trace #BR exceptions
This is the first in a series of MPX tracing patches.
I've found these extremely useful in the process of
debugging applications and the kernel code itself.
This exception hooks in to the bounds (#BR) exception
very early and allows capturing the key registers which
would influence how the exception is handled.
Note that bndcfgu/bndstatus are technically still
64-bit registers even in 32-bit mode.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183703.5FE2619A@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:02 +0000 (11:37 -0700)]
x86/mpx: Introduce a boot-time disable flag
MPX has the _potential_ to cause some issues. Say part of your
init system tried to protect one of its components from buffer
overflows with MPX. If there were a false positive, it's
possible that MPX could keep a system from booting.
MPX could also potentially cause performance issues since it is
present in hot paths like the unmap path.
Allow it to be disabled at boot time.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150607183702.2E8B77AB@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:02 +0000 (11:37 -0700)]
x86/mpx: Restrict the mmap() size check to bounds tables
The comment and code here are confusing. We do not currently
allocate the bounds directory in the kernel.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183702.222CEC2A@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Qiaowei Ren [Sun, 7 Jun 2015 18:37:02 +0000 (11:37 -0700)]
x86/mpx: Remove redundant MPX_BNDCFG_ADDR_MASK
MPX_BNDCFG_ADDR_MASK is defined two times, so this patch removes
redundant one.
Signed-off-by: Qiaowei Ren <qiaowei.ren@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183702.5F129376@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:02 +0000 (11:37 -0700)]
x86/mpx: Clean up the code by not passing a task pointer around when unnecessary
The MPX code can only work on the current task. You can not,
for instance, enable MPX management in another process or
thread. You can also not handle a fault for another process or
thread.
Despite this, we pass a task_struct around prolifically. This
patch removes all of the task struct passing for code paths
where the code can not deal with another task (which turns out
to be all of them).
This has no functional changes. It's just a cleanup.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: bp@alien8.de
Link: http://lkml.kernel.org/r/20150607183702.6A81DA2C@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:01 +0000 (11:37 -0700)]
x86/mpx: Use the new get_xsave_field_ptr()API
The MPX registers (bndcsr/bndcfgu/bndstatus) are not directly
accessible via normal instructions. They essentially act as
if they were floating point registers and are saved/restored
along with those registers.
There are two main paths in the MPX code where we care about
the contents of these registers:
1. #BR (bounds) faults
2. the prctl() code where we are setting MPX up
Both of those paths _might_ be called without the FPU having
been used. That means that 'tsk->thread.fpu.state' might
never be allocated.
Also, fpu_save_init() is not preempt-safe. It was a bug to
call it without disabling preemption. The new
get_xsave_addr() calls unlazy_fpu() instead and properly
disables preemption.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: bp@alien8.de
Link: http://lkml.kernel.org/r/20150607183701.BC0D37CF@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:00 +0000 (11:37 -0700)]
x86/fpu/xstate: Wrap get_xsave_addr() to make it safer
The MPX code appears is calling a low-level FPU function
(copy_fpregs_to_fpstate()). This function is not able to
be called in all contexts, although it is safe to call
directly in some cases.
Although probably correct, the current code is ugly and
potentially error-prone. So, add a wrapper that calls
the (slightly) higher-level fpu__save() (which is preempt-
safe) and also ensures that we even *have* an FPU context
(in the case that this was called when in lazy FPU mode).
Ingo had this to say about the details about when we need
preemption disabled:
> it's indeed generally unsafe to access/copy FPU registers with preemption enabled,
> for two reasons:
>
> - on older systems that use FSAVE the instruction destroys FPU register
> contents, which has to be handled carefully
>
> - even on newer systems if we copy to FPU registers (which this code doesn't)
> then we don't want a context switch to occur in the middle of it, because a
> context switch will write to the fpstate, potentially overwriting our new data
> with old FPU state.
>
> But it's safe to access FPU registers with preemption enabled in a couple of
> special cases:
>
> - potentially destructively saving FPU registers: the signal handling code does
> this in copy_fpstate_to_sigframe(), because it can rely on the signal restore
> side to restore the original FPU state.
>
> - reading FPU registers on modern systems: we don't do this anywhere at the
> moment, mostly to keep symmetry with older systems where FSAVE is
> destructive.
>
> - initializing FPU registers on modern systems: fpu__clear() does this. Here
> it's safe because we don't copy from the fpstate.
>
> - directly writing FPU registers from user-space memory (!). We do this in
> fpu__restore_sig(), and it's safe because neither context switches nor
> irq-handler FPU use can corrupt the source context of the copy (which is
> user-space memory).
>
> Note that the MPX code's current use of copy_fpregs_to_fpstate() was safe I think,
> because:
>
> - MPX is predicated on eagerfpu, so the destructive F[N]SAVE instruction won't be
> used.
>
> - the code was only reading FPU registers, and was doing it only in places that
> guaranteed that an FPU state was already active (i.e. didn't do it in
> kthreads)
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: bp@alien8.de
Link: http://lkml.kernel.org/r/20150607183700.AA881696@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Sun, 7 Jun 2015 18:37:00 +0000 (11:37 -0700)]
x86/fpu/xstate: Fix up bad get_xsave_addr() assumptions
get_xsave_addr() assumes that if an xsave bit is present in the
hardware (pcntxt_mask) that it is present in a given xsave
buffer. Due to an bug in the xsave code on all of the systems
that have MPX (and thus all the users of this code), that has
been a true assumption.
But, the bug is getting fixed, so our assumption is not going
to hold any more.
It's quite possible (and normal) for an enabled state to be
present on 'pcntxt_mask', but *not* in 'xstate_bv'. We need
to consult 'xstate_bv'.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150607183700.1E739B34@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 10:22:29 +0000 (12:22 +0200)]
x86/fpu: Make WARN_ON_FPU() more robust in the !CONFIG_X86_DEBUG_FPU case
Make sure the WARN_ON_FPU() macro consumes the macro argument,
to avoid 'unused variable' build warnings if the only use of
a variable is in debugging code.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 12:04:44 +0000 (14:04 +0200)]
x86/fpu: Simplify copy_kernel_to_xregs_booting()
copy_kernel_to_xregs_booting() has a second parameter that is the mask
of xfeatures that should be copied - but this parameter is always -1.
Simplify the call site of this function, this also makes it more
similar to the function call signature of other copy_kernel_to*regs()
functions.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 09:59:35 +0000 (11:59 +0200)]
x86/fpu: Standardize the parameter type of copy_kernel_to_fpregs()
Bring the __copy_fpstate_to_fpregs() and copy_fpstate_to_fpregs() functions
in line with the parameter passing convention of other kernel-to-FPU-registers
copying functions: pass around an in-memory FPU register state pointer,
instead of struct fpu *.
NOTE: This patch also changes the assembly constraint of the FXSAVE-leak
workaround from 'fpu->fpregs_active' to 'fpstate' - but that is fine,
as we only need a valid memory address there for the FILDL instruction.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 09:27:46 +0000 (11:27 +0200)]
x86/fpu: Remove error return values from copy_kernel_to_*regs() functions
None of the copy_kernel_to_*regs() FPU register copying functions are
supposed to fail, and all of them have debugging checks that enforce
this.
Remove their return values and simplify their call sites, which have
redundant error checks and error handling code paths.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 11:47:01 +0000 (13:47 +0200)]
x86/fpu: Rename copy_fpstate_to_fpregs() to copy_kernel_to_fpregs()
Bring the __copy_fpstate_to_fpregs() and copy_fpstate_to_fpregs() functions
in line with the naming of other kernel-to-FPU-registers copying functions.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 08:59:31 +0000 (10:59 +0200)]
x86/fpu: Add debugging checks to all copy_kernel_to_*() functions
Copying from in-kernel FPU context buffers to FPU registers are
never supposed to fault.
Add debugging checks to copy_kernel_to_fxregs() and copy_kernel_to_fregs()
to double check this assumption.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 08:57:06 +0000 (10:57 +0200)]
x86/fpu: Add debugging check to fpu__restore()
The copy_fpstate_to_fpregs() function is never supposed to fail,
so add a debugging check to its call site in fpu__restore().
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 10:22:29 +0000 (12:22 +0200)]
x86/fpu: Optimize fpu__activate_fpstate_write()
fpu__activate_fpstate_write() is used before ptrace writes to the fpstate
context. Because it expects the modified registers to be reloaded on the
nexts context switch, it's only valid to call this function for stopped
child tasks.
- add a debugging check for this assumption
- remove code that only runs if the current task's FPU state needs
to be saved, which cannot occur here
- update comments to match the implementation
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 10:22:29 +0000 (12:22 +0200)]
x86/fpu: Rename fpu__activate_fpstate() to fpu__activate_fpstate_write()
Remaining users of fpu__activate_fpstate() are all places that want to modify
FPU registers, rename the function to fpu__activate_fpstate_write() according
to this usage.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 10:22:29 +0000 (12:22 +0200)]
x86/fpu: Optimize fpu__activate_fpstate_read()
fpu__activate_fpstate_read() is used before FPU registers are
read from the fpstate by ptrace and core dumping.
It's not necessary to unlazy non-current child tasks in this case,
since the reading of registers is non-destructive.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 10:22:29 +0000 (12:22 +0200)]
x86/fpu: Split out the fpu__activate_fpstate_read() method
Currently fpu__activate_fpstate() is used for two distinct purposes:
- read access by ptrace and core dumping, where in the core dumping
case the current task's FPU state may be examined as well.
- write access by ptrace, which modifies FPU registers and expects
the modified registers to be reloaded on the next context switch.
Split out the reading side into fpu__activate_fpstate_read().
( Note that this is just a pure duplication of fpu__activate_fpstate()
for the time being, we'll optimize the new function in the next patch. )
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 27 May 2015 10:22:29 +0000 (12:22 +0200)]
x86/fpu: Fix FPU register read access to the current task
Bobby Powers reported the following FPU warning during ELF coredumping:
WARNING: CPU: 0 PID: 27452 at arch/x86/kernel/fpu/core.c:324 fpu__activate_stopped+0x8a/0xa0()
This warning unearthed an invalid assumption about fpu__activate_stopped()
that I added in:
67e97fc2ec57 ("x86/fpu: Rename init_fpu() to fpu__unlazy_stopped() and add debugging check")
the old init_fpu() function had an (intentional but obscure) side effect:
when FPU registers are accessed for the current task, for reading, then
it synchronized live in-register FPU state with the fpstate by saving it.
So fix this bug by saving the FPU if we are the current task. We'll
still warn in fpu__save() if this is called for not yet stopped
child tasks, so the debugging check is still preserved.
Also rename the function to fpu__activate_fpstate(), because it's not
exclusively used for stopped tasks, but for the current task as well.
( Note that this bug calls for a cleaner separation of access-for-read
and access-for-modification FPU methods, but we'll do that in separate
patches. )
Reported-by: Bobby Powers <bobbypowers@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Sun, 24 May 2015 07:23:25 +0000 (09:23 +0200)]
x86/fpu: Micro-optimize the copy_xregs_to_kernel*() and copy_kernel_to_xregs*() functions
The copy_xregs_to_kernel*() and copy_kernel_to_xregs*() functions are used
to copy FPU registers to kernel memory and vice versa.
They are never expected to fail, yet they have a return code, mostly because
that way they can share the assembly macros with the copy*user*() functions.
This error code is then silently ignored by the context switching
and other code - which made the bug in:
b8c1b8ea7b21 ("x86/fpu: Fix FPU state save area alignment bug")
harder to fix than necessary.
So remove the return values and check for no faults when FPU debugging
is enabled in the .config.
This improves the eagerfpu context switching fast path by a couple of
instructions, when FPU debugging is disabled:
ffffffff810407fa: 89 c2 mov %eax,%edx
ffffffff810407fc: 48 0f ae 2f xrstor64 (%rdi)
ffffffff81040800: 31 c0 xor %eax,%eax
-
ffffffff81040802: eb 0a jmp
ffffffff8104080e <__switch_to+0x321>
+
ffffffff81040802: eb 16 jmp
ffffffff8104081a <__switch_to+0x32d>
ffffffff81040804: 31 c0 xor %eax,%eax
ffffffff81040806: 48 0f ae 8b c0 05 00 fxrstor64 0x5c0(%rbx)
ffffffff8104080d: 00
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 09:59:35 +0000 (11:59 +0200)]
x86/fpu: Improve the initialization logic of 'err' around xstate_fault() constraints
There's a confusing aspect of how xstate_fault() constraints are
handled by the FPU register/memory copying functions in
fpu/internal.h: they use "0" (0) to signal that the asm code
will not always set 'err' to a valid value.
But 'err' is already initialized to 0 in C code, which is duplicated
by the asm() constraint. Should the initialization value ever be
changed, it might become subtly inconsistent with the not too clear
asm() constraint.
Use 'err' as the value of the input variable instead, to clarify
this all.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 09:27:46 +0000 (11:27 +0200)]
x86/fpu: Improve xstate_fault() handling
There are two problems with xstate_fault handling:
- The xstate_fault() macro takes an argument, but that's
propagated into the assembly named label as well. This
is technically correct currently but might result in
failures if anytime a more complex argument is used.
So use a separate '_err' name instead for the label.
- All the xstate_fault() using functions have an error
variable named 'err', which is an output variable to
the asm() they are using. The problem is, it's not always
set by the asm(), in which case the compiler might
optimize out its initialization, so that the C variable
'err' might become corrupted after the asm() - confusing
anyone who tries to take advantage of this variable
after the asm(). Mark it an input variable as well.
This is a latent bug currently, but an upcoming debug
patch will make use of 'err'.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 08:57:06 +0000 (10:57 +0200)]
x86/fpu: Rename xstate related 'fx' references to 'xstate'
So the xstate code was probably first copied from the fxregs code,
hence it carried over the 'fx' naming for the state pointer variable.
But this is slightly confusing, as we usually on call the (legacy)
MMX/SSE state 'fx', both in data structures and in the functions
build around FXSAVE/FXRSTOR.
So rename it to 'xstate' to make it more apparent what it is related to.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Sun, 24 May 2015 07:58:12 +0000 (09:58 +0200)]
x86/fpu: Fix fpu__init_system_xstate() comments
Remove obsolete comment about __init limitations: in the new code there aren't any.
Also standardize the comment style in the function while at it.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Mon, 25 May 2015 07:55:39 +0000 (09:55 +0200)]
x86/fpu: Move the xstate copying functions into fpu/internal.h
All the other register<-> memory copying functions are defined
in fpu/internal.h, so move the xstate variants there too.
Beyond being more consistent, this also allows FPU debugging
checks to be added to them. (Because they can now use the
macros defined in fpu/internal.h.)
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Sat, 23 May 2015 14:47:12 +0000 (16:47 +0200)]
Merge branch 'linus' into x86/fpu
Resolve semantic conflict in arch/x86/kvm/cpuid.c with:
c447e76b4cab ("kvm/fpu: Enable eager restore kvm FPU for MPX")
By removing the FPU internal include files.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Sun, 24 May 2015 07:58:12 +0000 (09:58 +0200)]
x86/fpu: Fix FPU state save area alignment bug
On most configs task-struct is cache line aligned, which makes
the XSAVE area's 64-byte required alignment work out fine.
But on some .config's task_struct is aligned only to 16 bytes
(enforced by ARCH_MIN_TASKALIGN), which makes things like
fpu__copy() (that XSAVEOPT uses) not work so well.
I broke this in:
7366ed771f6e ("x86/fpu: Simplify FPU handling by embedding the fpstate in task_struct (again)")
which embedded the fpstate in the task_struct.
The alignment requirements of the FPU code were originally present
in ARCH_MIN_TASKALIGN, which still has a value of 16, which was the
alignment requirement of the FPU state area prior XSAVE. But this
link was not documented (and not required) and the link got lost
when the FPU state area was made dynamic years ago.
With XSAVEOPT the minimum alignment requirment went up to 64 bytes,
and the embedding of the FPU state area in task_struct exposed it
again - and '16' was not increased to '64'.
So fix this bug, but also try to address the underlying lost link
of information that made it easier to happen:
- document ARCH_MIN_TASKALIGN a bit better
- use alignof() to recover the current alignment requirements.
This would work in the future as well, should the alignment
requirements go up to 128 bytes with things like AVX512.
( We should probably also use the vSMP alignment rules for all
of x86, but that's for another patch. )
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Mon, 25 May 2015 01:22:35 +0000 (18:22 -0700)]
Linux 4.1-rc5
Linus Torvalds [Sun, 24 May 2015 18:15:28 +0000 (11:15 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five fixes: Two MAINTAINER email updates (urgent
because the non-avagotech emails will start bouncing) an lpfc big
endian oops fix, a 256 byte sector hang fix (to eliminate 256 byte
sectors) and a storvsc fix which could cause test unit ready failures
on bringup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: Revise lpfc maintainers for Avago Technologies ownership of Emulex
MAINTAINERS, be2iscsi: change email domain
sd: Disable support for 256 byte/sector disks
lpfc: Fix breakage on big endian kernels
storvsc: Set the SRB flags correctly when no data transfer is needed
Linus Torvalds [Sun, 24 May 2015 00:57:40 +0000 (17:57 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"One more fix from the timer departement:
- Handle division of negative nanosecond values proper on 32bit.
A recent cleanup wrecked the sign handling of the dividend and
dropped the check for negative divisors"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Fix ktime_divns to do signed division
Linus Torvalds [Sun, 24 May 2015 00:33:10 +0000 (17:33 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irqchip fix from Thomas Gleixner:
"A fix for a GIC-V3 irqchip regression which prevents some systems from
booting"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
Linus Torvalds [Sat, 23 May 2015 18:28:25 +0000 (11:28 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull two Ceph fixes from Sage Weil:
"These fix an issue with the RBD notifications when there are topology
changes in the cluster"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
libceph: request a new osdmap if lingering request maps to no osd
Linus Torvalds [Sat, 23 May 2015 18:14:10 +0000 (11:14 -0700)]
Merge branch 'for-linus-4.1' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I fixed up a regression from 4.0 where conversion between different
raid levels would sometimes bail out without converting.
Filipe tracked down a race where it was possible to double allocate
chunks on the drive.
Mark has a fix for fiemap. All three will get bundled off for stable
as well"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix regression in raid level conversion
Btrfs: fix racy system chunk allocation when setting block group ro
btrfs: clear 'ret' in btrfs_check_shared() loop
Linus Torvalds [Sat, 23 May 2015 00:34:24 +0000 (17:34 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
Linus Torvalds [Fri, 22 May 2015 22:44:50 +0000 (15:44 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Linus Torvalds [Fri, 22 May 2015 22:15:30 +0000 (15:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
Linus Torvalds [Fri, 22 May 2015 22:10:07 +0000 (15:10 -0700)]
Merge tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"I have a few more raid5 bugfixes pending, but I want them to get a bit
more review first. In the meantime:
- one serious RAID0 data corruption - caused by recent bugfix that
wasn't reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation"
* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
md/bitmap: remove rcu annotation from pointer arithmetic.
md/raid0: fix restore to sector variable in raid0_make_request
raid5: fix broken async operation chain
Linus Torvalds [Fri, 22 May 2015 21:49:55 +0000 (14:49 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Linus Torvalds [Fri, 22 May 2015 21:26:36 +0000 (14:26 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull another crypto fix from Herbert Xu:
"Fix ICV corruption in s390/ghash when the same tfm is used by more
than one thread"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390/ghash - Fix incorrect ghash icv buffer handling.
Eric Dumazet [Thu, 21 May 2015 20:28:29 +0000 (13:28 -0700)]
bridge: fix lockdep splat
Following lockdep splat was reported :
[ 29.382286] ===============================
[ 29.382315] [ INFO: suspicious RCU usage. ]
[ 29.382344] 4.1.0-0.rc0.git11.1.fc23.x86_64 #1 Not tainted
[ 29.382380] -------------------------------
[ 29.382409] net/bridge/br_private.h:626 suspicious
rcu_dereference_check() usage!
[ 29.382455]
other info that might help us debug this:
[ 29.382507]
rcu_scheduler_active = 1, debug_locks = 0
[ 29.382549] 2 locks held by swapper/0/0:
[ 29.382576] #0: (((&p->forward_delay_timer))){+.-...}, at:
[<
ffffffff81139f75>] call_timer_fn+0x5/0x4f0
[ 29.382660] #1: (&(&br->lock)->rlock){+.-...}, at:
[<
ffffffffa0450dc1>] br_forward_delay_timer_expired+0x31/0x140
[bridge]
[ 29.382754]
stack backtrace:
[ 29.382787] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
4.1.0-0.rc0.git11.1.fc23.x86_64 #1
[ 29.382838] Hardware name: LENOVO 422916G/LENOVO, BIOS A1KT53AUS 04/07/2015
[ 29.382882]
0000000000000000 3ebfc20364115825 ffff880666603c48
ffffffff81892d4b
[ 29.382943]
0000000000000000 ffffffff81e124e0 ffff880666603c78
ffffffff8110bcd7
[ 29.383004]
ffff8800785c9d00 ffff88065485ac58 ffff880c62002800
ffff880c5fc88ac0
[ 29.383065] Call Trace:
[ 29.383084] <IRQ> [<
ffffffff81892d4b>] dump_stack+0x4c/0x65
[ 29.383130] [<
ffffffff8110bcd7>] lockdep_rcu_suspicious+0xe7/0x120
[ 29.383178] [<
ffffffffa04520f9>] br_fill_ifinfo+0x4a9/0x6a0 [bridge]
[ 29.383225] [<
ffffffffa045266b>] br_ifinfo_notify+0x11b/0x4b0 [bridge]
[ 29.383271] [<
ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[ 29.383320] [<
ffffffffa0450de8>]
br_forward_delay_timer_expired+0x58/0x140 [bridge]
[ 29.383371] [<
ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[ 29.383416] [<
ffffffff8113a033>] call_timer_fn+0xc3/0x4f0
[ 29.383454] [<
ffffffff81139f75>] ? call_timer_fn+0x5/0x4f0
[ 29.383493] [<
ffffffff8110a90f>] ? lock_release_holdtime.part.29+0xf/0x200
[ 29.383541] [<
ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[ 29.383587] [<
ffffffff8113a6a4>] run_timer_softirq+0x244/0x490
[ 29.383629] [<
ffffffff810b68cc>] __do_softirq+0xec/0x670
[ 29.383666] [<
ffffffff810b70d5>] irq_exit+0x145/0x150
[ 29.383703] [<
ffffffff8189f506>] smp_apic_timer_interrupt+0x46/0x60
[ 29.383744] [<
ffffffff8189d523>] apic_timer_interrupt+0x73/0x80
[ 29.383782] <EOI> [<
ffffffff816f131f>] ? cpuidle_enter_state+0x5f/0x2f0
[ 29.383832] [<
ffffffff816f131b>] ? cpuidle_enter_state+0x5b/0x2f0
Problem here is that br_forward_delay_timer_expired() is a timer
handler, calling br_ifinfo_notify() which assumes either rcu_read_lock()
or RTNL are held.
Simplest fix seems to add rcu read lock section.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Dominick Grift <dac.override@gmail.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Wed, 20 May 2015 21:35:30 +0000 (14:35 -0700)]
net: core: 'ethtool' issue with querying phy settings
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thadeu Lima de Souza Cascardo [Fri, 22 May 2015 15:18:59 +0000 (12:18 -0300)]
bridge: fix parsing of MLDv2 reports
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.")
Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:11 +0000 (09:22 -0500)]
ARM: zynq: DT: Use the zynq binding with macb
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:10 +0000 (09:22 -0500)]
net: macb: Disable half duplex gigabit on Zynq
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Fri, 22 May 2015 14:22:09 +0000 (09:22 -0500)]
net: macb: Document zynq gem dt binding
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Fri, 22 May 2015 11:40:09 +0000 (13:40 +0200)]
ipv4: fill in table id when replacing a route
When replacing an IPv4 route, tb_id member of the new fib_alias
structure is not set in the replace code path so that the new route is
ignored.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 22 May 2015 11:15:22 +0000 (13:15 +0200)]
cdc_ncm: Fix tx_bytes statistics
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2015 18:25:45 +0000 (14:25 -0400)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Fri, 22 May 2015 09:58:12 +0000 (04:58 -0500)]
ipv4: Avoid crashing in ip_error
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.")
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 May 2015 04:51:19 +0000 (21:51 -0700)]
tcp: fix a potential deadlock in tcp_get_info()
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<
ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<
ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<
ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<
ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<
ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<
ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<
ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<
ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<
ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<
ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<
ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<
ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<
ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo Molnar [Fri, 22 May 2015 08:58:45 +0000 (10:58 +0200)]
x86/fpu, crypto: Fix AVX2 feature tests
For some CPU models I broke the AVX2 feature detection in:
7bc371faa9cd ("x86/fpu, crypto x86/camellia_aesni_avx2: Simplify the camellia_aesni_init() xfeature checks")
534ff06e3929 ("x86/fpu, crypto x86/serpent_avx2: Simplify the init() xfeature checks")
... because I did not realize that it's possible for a CPU to support
the xstate necessary for AVX2 execution (XSTATE_YMM), but not have
the AVX2 instructions themselves.
Restore the necessary CPUID checks as well.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Fri, 22 May 2015 03:31:54 +0000 (13:31 +1000)]
Merge branch 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just two small DP fixes for 4.1
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
Dave Airlie [Fri, 22 May 2015 03:31:03 +0000 (13:31 +1000)]
Merge tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel into drm-fixes
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
Harald Freudenberger [Thu, 21 May 2015 08:01:11 +0000 (10:01 +0200)]
crypto: s390/ghash - Fix incorrect ghash icv buffer handling.
Multitheaded tests showed that the icv buffer in the current ghash
implementation is not handled correctly. A move of this working ghash
buffer value to the descriptor context fixed this. Code is tested and
verified with an multithreaded application via af_alg interface.
Cc: stable@vger.kernel.org
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <geraldsc@linux.vnet.ibm.com>
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Fri, 22 May 2015 03:19:38 +0000 (20:19 -0700)]
Merge tag 'for-linus-4.1b-rc4-tag' of git://git./linux/kernel/git/xen/tip
Pull two xen bugfixes from David Vrabel:
- fix ARM build regression.
- fix VIRQ_CONSOLE related oops.
* tag 'for-linus-4.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't bind non-percpu VIRQs with percpu chip
xen/arm: Define xen_arch_suspend()
Linus Torvalds [Fri, 22 May 2015 03:15:16 +0000 (20:15 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"This includes a fix for two oopses, one on PPC and on x86.
The rest is fixes for bugs with newer Intel processors"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm/fpu: Enable eager restore kvm FPU for MPX
Revert "KVM: x86: drop fpu_activate hook"
kvm: fix crash in kvm_vcpu_reload_apic_access_page
KVM: MMU: fix SMAP virtualization
KVM: MMU: fix CR4.SMEP=1, CR0.WP=0 with shadow pages
KVM: MMU: fix smap permission check
KVM: PPC: Book3S HV: Fix list traversal in error case
Linus Torvalds [Fri, 22 May 2015 02:54:50 +0000 (19:54 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes.
Three for our crypto code, two for eBPF, and one memory management fix
to get machines with memory > 8TB working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: correct return value of pmd_pfn
s390/crypto: fix stckf loop
s390/zcrypt: Fix invalid domain handling during ap module unload
s390/bpf: Fix gcov stack space problem
s390/zcrypt: fixed ap poll timer behavior
s390/bpf: Adjust ALU64_DIV/MOD to match interpreter change
Linus Torvalds [Fri, 22 May 2015 00:54:00 +0000 (17:54 -0700)]
Merge tag 'sound-4.1-rc5' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch became slightly large, just because I've been on vacation
for the last two weeks. Nothing to scare much here, all
device-specific fixes, mostly small patches.
Majority of patches are for HD-audio, especially Dell machines. The
rest are small ASoC fixes for various codecs, and a USB-audio quirk.
One PCM fix is included to ease the faulty condition checks in the
case of two periods PCM buffers"
* tag 'sound-4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable widget power-saving for ALC292 & co
ALSA: hda - Reduce verbs by node power-saves
ALSA: sound/atmel/ac97c.c: remove unused variable
ALSA: usb-audio: Add quirk for MS LifeCam Studio
ALSA: pcm: Modify double acknowledged interrupts check condition
ALSA: hda/realtek - ALC292 dock fix for Thinkpad L450
ALSA: hda - Add Conexant codecs CX20721, CX20722, CX20723 and CX20724
ALSA: hda - Fix headset mic and mic-in for a Dell desktop
ASoC: wm8994: correct BCLK DIV 348 to 384
ASoC: wm8960: fix "RINPUT3" audio route error
ASoC: dapm: Modify widget stream name according to prefix
ALSA: hda - Add headset mic quirk for Dell Inspiron 5548
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ASoC: rt5645: Add ACPI match ID
ALSA: hda/realtek - Add ALC298 alias name for Dell
ASoC: uda1380: Avoid accessing i2c bus when codec is disabled
ALSA: hda/realtek - Fix typo for ALC286/ALC288
ASoC: mc13783: Fix wrong mask value used in mc13xxx_reg_rmw() calls
ALSA: hda - Add headphone quirk for Lifebook E752
ASoC: davinci-mcasp: Correct pm status check in suspend callback
Linus Torvalds [Fri, 22 May 2015 00:42:54 +0000 (17:42 -0700)]
Merge branch 'for-rc' of git://git./linux/kernel/git/rzhang/linux
Pull thermal fixes from Zhang Rui:
"Three fixes for Armada (380) and TI (dra7 and OMAP5) thermal soc
drivers"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: armada: Update Armada 380 thermal sensor coefficients
thermal: ti-soc-thermal: OMAP5: Implement Workaround for Errata i813
thermal: ti-soc-thermal: dra7: Implement Workaround for Errata i814
Linus Torvalds [Fri, 22 May 2015 00:36:23 +0000 (17:36 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull infiniband/rdma fixes from Doug Ledford:
"This should hopefully be the last request for 4.1-rc for the RDMA
stack. It contains some late ocrdma fixes that I'm including because
they are small and self contained. It also contains two bug fixes
that are simple and easily verified.
Summary:
- a number of small, well contained bug fixes for ocrdma driver
- a simple fix for the connection negotiation sequence on IB
- fix for broken AF_IB address on UD queue pair support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/cma: Fix broken AF_IB UD support
ib/cm: Change reject message type when destroying cm_id
RDMA/ocrdma: Update ocrdma version number
RDMA/ocrdma: Fail connection for MTU lesser than 512
RDMA/ocrdma: Fix dmac resolution for link local address
RDMA/ocrdma: Prevent allocation of DPP PDs if FW doesnt support it
RDMA/ocrdma: Fix the request length for RDMA_QUERY_QP mailbox command to FW.
RDMA/ocrdma: Use VID 0 if PFC is enabled and vlan is not configured
RDMA/ocrdma: Fix QP state transition in destroy_qp
RDMA/ocrdma: Report EQ full fatal error
RDMA/ocrdma: Fix EQ destroy failure during driver unload
Linus Torvalds [Fri, 22 May 2015 00:31:31 +0000 (17:31 -0700)]
Merge tag 'mmc-4.1-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fix from Ulf Hansson:
"One more mmc fix intended for v4.1 rc5:
MMC host:
- atmel-mci: fix bad variable type for clkdiv"
* tag 'mmc-4.1-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: atmel-mci: fix bad variable type for clkdiv
Linus Torvalds [Fri, 22 May 2015 00:23:11 +0000 (17:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
Linus Torvalds [Fri, 22 May 2015 00:16:49 +0000 (17:16 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a the crash in the newly added algif_aead interface when it
tries to link SG lists"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_aead - fix invalid sgl linking
Marek Vasut [Fri, 8 May 2015 05:25:49 +0000 (22:25 -0700)]
Input: smtpe-ts - wait 50mS until polling for pen-up
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Marek Vasut [Fri, 8 May 2015 05:24:58 +0000 (22:24 -0700)]
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds [Thu, 21 May 2015 23:57:50 +0000 (16:57 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
Linus Torvalds [Thu, 21 May 2015 23:38:14 +0000 (16:38 -0700)]
Merge tag 'hwmon-for-linus-v4.1-rc5' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixlet from Guenter Roeck:
"Update location of Jean Delvare's hwmon quilt tree"
* tag 'hwmon-for-linus-v4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Update the location of my quilt tree
Thomas Hellstrom [Wed, 20 May 2015 21:50:30 +0000 (14:50 -0700)]
Input: joydev - don't classify the vmmouse as a joystick
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Daniel Borkmann [Wed, 20 May 2015 15:13:33 +0000 (17:13 +0200)]
net: sched: fix call_rcu() race on classifier module unloads
Vijay reported that a loop as simple as ...
while true; do
tc qdisc add dev foo root handle 1: prio
tc filter add dev foo parent 1: u32 match u32 0 0 flowid 1
tc qdisc del dev foo root
rmmod cls_u32
done
... will panic the kernel. Moreover, he bisected the change
apparently introducing it to
78fd1d0ab072 ("netlink: Re-add
locking to netlink_lookup() and seq walker").
The removal of synchronize_net() from the netlink socket
triggering the qdisc to be removed, seems to have uncovered
an RCU resp. module reference count race from the tc API.
Given that RCU conversion was done after
e341694e3eb5 ("netlink:
Convert netlink_lookup() to use RCU protected hash table")
which added the synchronize_net() originally, occasion of
hitting the bug was less likely (not impossible though):
When qdiscs that i) support attaching classifiers and,
ii) have at least one of them attached, get deleted, they
invoke tcf_destroy_chain(), and thus call into ->destroy()
handler from a classifier module.
After RCU conversion, all classifier that have an internal
prio list, unlink them and initiate freeing via call_rcu()
deferral.
Meanhile, tcf_destroy() releases already reference to the
tp->ops->owner module before the queued RCU callback handler
has been invoked.
Subsequent rmmod on the classifier module is then not prevented
since all module references are already dropped.
By the time, the kernel invokes the RCU callback handler from
the module, that function address is then invalid.
One way to fix it would be to add an rcu_barrier() to
unregister_tcf_proto_ops() to wait for all pending call_rcu()s
to complete.
synchronize_rcu() is not appropriate as under heavy RCU
callback load, registered call_rcu()s could be deferred
longer than a grace period. In case we don't have any pending
call_rcu()s, the barrier is allowed to return immediately.
Since we came here via unregister_tcf_proto_ops(), there
are no users of a given classifier anymore. Further nested
call_rcu()s pointing into the module space are not being
done anywhere.
Only cls_bpf_delete_prog() may schedule a work item, to
unlock pages eventually, but that is not in the range/context
of cls_bpf anymore.
Fixes: 25d8c0d55f24 ("net: rcu-ify tcf_proto")
Fixes: 9888faefe132 ("net: sched: cls_basic use RCU")
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Deucher [Wed, 20 May 2015 21:58:49 +0000 (17:58 -0400)]
drm/radeon: fix error flag checking in native aux path
That atom table does not check these bits. Fixes aux
regressions on some boards.
Reported-by: Malte Schröder <malte@tnxip.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Mon, 18 May 2015 14:38:25 +0000 (10:38 -0400)]
drm/radeon: retry dcpd fetch
Retry the dpcd fetch several times. Some eDP panels
fail several times before the fetch is successful.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73530
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Stephane Viau [Wed, 20 May 2015 14:57:27 +0000 (10:57 -0400)]
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
The index of ->planes[] array (3rd parameter) cannot be equal to MAX_PLANE.
This looks like a typo that is now fixed.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NeilBrown [Wed, 20 May 2015 05:05:09 +0000 (15:05 +1000)]
md/bitmap: remove rcu annotation from pointer arithmetic.
Evaluating "&mddev->disks" is simple pointer arithmetic, so
it does not need 'rcu' annotations - no dereferencing is happening.
Also enhance the comment to explain that 'rdev' in that case
is not actually a pointer to an rdev.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Eric Work [Tue, 19 May 2015 06:26:23 +0000 (23:26 -0700)]
md/raid0: fix restore to sector variable in raid0_make_request
The variable "sector" in "raid0_make_request()" was improperly updated
by a call to "sector_div()" which modifies its first argument in place.
Commit
47d68979cc968535cb87f3e5f2e6a3533ea48fbd restored this variable
after the call for later re-use. Unfortunetly the restore was done after
the referenced variable "bio" was advanced. This lead to the original
value and the restored value being different. Here we move this line to
the proper place.
One observed side effect of this bug was discarding a file though
unlinking would cause an unrelated file's contents to be discarded.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 47d68979cc96 ("md/raid0: fix bug with chunksize not a power of 2.")
Cc: stable@vger.kernel.org (any that received above backport)
URL: https://bugzilla.kernel.org/show_bug.cgi?id=98501
Shaohua Li [Wed, 13 May 2015 16:30:08 +0000 (09:30 -0700)]
raid5: fix broken async operation chain
ops_run_reconstruct6() doesn't correctly chain asyn operations. The tx returned
by async_gen_syndrome should be added as the dependent tx of next stripe.
The issue is introduced by commit
59fc630b8b5f9f21c8ce3ba153341c107dce1b0c
RAID5: batch adjacent full stripe write
Reported-and-tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Thomas Hellstrom [Wed, 20 May 2015 21:46:14 +0000 (14:46 -0700)]
Input: vmmouse - do not reference non-existing version of X driver
The vmmouse Kconfig help text was referring to an incorrect user-space
driver version. Fix this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Hans de Goede [Wed, 20 May 2015 21:37:41 +0000 (14:37 -0700)]
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=
1025058
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1221200
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Matthew Finlay [Tue, 19 May 2015 07:11:48 +0000 (00:11 -0700)]
IB/cma: Fix broken AF_IB UD support
Support for using UD and AF_IB is currently broken. The
IB_CM_SIDR_REQ_RECEIVED message is not handled properly in
cma_save_net_info() and we end up falling into code that will try and
process the request as ipv4/ipv6, which will end up failing.
The resolution is to add a check for the SIDR_REQ and call
cma_save_ib_info() with a NULL path record. Change cma_save_ib_info()
to copy the src sib info from the listen_id when the path record is NULL.
Reported-by: Hari Shankar <Hari.Shankar@netapp.com>
Signed-off-by: Matt Finlay <matt@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Minghuan Lian [Wed, 20 May 2015 15:13:15 +0000 (10:13 -0500)]
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
When allocating a device table, if the requested allocation is smaller
than the default granule size of the ITS then, we need to round up to
the default size.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
[ stuart: Added comments and massaged changelog ]
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Reviewed-by: Marc Zygnier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1432134795-661-1-git-send-email-stuart.yoder@freescale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chris Mason [Wed, 20 May 2015 01:54:41 +0000 (18:54 -0700)]
Btrfs: fix regression in raid level conversion
Commit
2f0810880f082fa8ba66ab2c33b02e4ff9770a5e changed
btrfs_set_block_group_ro to avoid trying to allocate new chunks with the
new raid profile during conversion. This fixed failures when there was
no space on the drive to allocate a new chunk, but the metadata
reserves were sufficient to continue the conversion.
But this ended up causing a regression when the drive had plenty of
space to allocate new chunks, mostly because reduce_alloc_profile isn't
using the new raid profile.
Fixing btrfs_reduce_alloc_profile is a bigger patch. For now, do a
partial revert of
2f0810880, and don't error out if we hit ENOSPC.
Signed-off-by: Chris Mason <clm@fb.com>
Tested-by: Dave Sterba <dsterba@suse.cz>
Reported-by: Holger Hoffstaette <holger.hoffstaette@googlemail.com>
Ilya Dryomov [Mon, 11 May 2015 14:53:34 +0000 (17:53 +0300)]
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
This reverts commit
ba9d114ec5578e6e99a4dfa37ff8ae688040fd64.
.. which introduced a regression that prevented all lingering requests
requeued in kick_requests() from ever being sent to the OSDs, resulting
in a lot of missed notifies. In retrospect it's pretty obvious that
r_req_lru_item item in the case of lingering requests can be used not
only for notarget, but also for unsent linkage due to how tightly
actual map and enqueue operations are coupled in __map_request().
The assertion that was being silenced is taken care of in the previous
("libceph: request a new osdmap if lingering request maps to no osd")
commit: by always kicking homeless lingering requests we ensure that
none of them ends up on the notarget list outside of the critical
section guarded by request_mutex.
Cc: stable@vger.kernel.org # 3.18+, needs b0494532214b "libceph: request a new osdmap if lingering request maps to no osd"
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Ilya Dryomov [Mon, 11 May 2015 14:53:10 +0000 (17:53 +0300)]
libceph: request a new osdmap if lingering request maps to no osd
This commit does two things. First, if there are any homeless
lingering requests, we now request a new osdmap even if the osdmap that
is being processed brought no changes, i.e. if a given lingering
request turned homeless in one of the previous epochs and remained
homeless in the current epoch. Not doing so leaves us with a stale
osdmap and as a result we may miss our window for reestablishing the
watch and lose notifies.
MON=1 OSD=1:
# cat linger-needmap.sh
#!/bin/bash
rbd create --size 1 test
DEV=$(rbd map test)
ceph osd out 0
rbd map dne/dne # obtain a new osdmap as a side effect (!)
sleep 1
ceph osd in 0
rbd resize --size 2 test
# rbd info test | grep size -> 2M
# blockdev --getsize $DEV -> 1M
N.B.: Not obtaining a new osdmap in between "osd out" and "osd in"
above is enough to make it miss that resize notify, but that is a
bug^Wlimitation of ceph watch/notify v1.
Second, homeless lingering requests are now kicked just like those
lingering requests whose mapping has changed. This is mainly to
recognize that a homeless lingering request makes no sense and to
preserve the invariant that a registered lingering request is not
sitting on any of r_req_lru_item lists. This spares us a WARN_ON,
which commit
ba9d114ec557 ("libceph: clear r_req_lru_item in
__unregister_linger_request()") tried to fix the _wrong_ way.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Ted Kim [Thu, 14 May 2015 19:49:01 +0000 (12:49 -0700)]
ib/cm: Change reject message type when destroying cm_id
Problem reported by: Ted Kim <ted.h.kim@oracle.com>:
We have a case where a Linux system and a non-Linux system are
trying to interoperate. The Linux host is the active side and
starts the connection establishment, but later decides to not go
through with the connection setup and does rdma_destroy_id().
The rdma_destroy_id() eventually works its way down to cm_destroy_id()
in core/cm.c, where a REJ is sent. The non-Linux system
has some trouble recognizing the REJ because of:
A. CM states which can't receive the REJ
B. Some issues about REJ formatting (missing comm ID)
ISSUE A: That part of the spec says, a Consumer Reject REJ can be
sent for a connection abort, but it goes further
and says: can send a REJ message with a "Consumer Reject"
Reason code if they are in a CM state (i.e. REP
Rcvd, MRA(REP) Sent, REQ Rcvd, MRA Sent) that allows
a REJ to be sent (lines 35-38).
Of the states listed there in that sentence, it would
seem to limit the active side to using the Consumer Reject
(for the abort case) in just the REP-Rcvd and MRA-REP-Sent
states. That is basically only after the active side
sees a REP (or alternatively goes down the state transitions
to timeout in which case a Timeout REJ is sent).
As a fix, in cm-destroy-id() move the IB-CM-MRA-REQ-RCVD case
to the same as REQ-SENT. Essentially, make a REJ sent after
getting an MRA on active side a timeout rather than Consumer-
Reject, which is arguably more correct with the CM state
diagrams previous to getting a REP.
Signed-off-by: Ted Kim <ted.h.kim@oracle.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Tim Beale [Mon, 18 May 2015 03:38:38 +0000 (15:38 +1200)]
net: phy: Make sure phy_start() always re-enables the phy interrupts
This is an alternative way of fixing:
commit
db9683fb412d ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 20 May 2015 16:02:26 +0000 (12:02 -0400)]
Merge branch 'ipv6_ecmp_fixes'
Michal Kubecek says:
====================
IPv6 ECMP route add/replace fixes
(1) When adding a nexthop of a multipath route fails (e.g. because of a
conflict with an existing route), we are supposed to delete nexthops
already added. However, currently we try to also delete all nexthops we
haven't even tried to add yet so that a "ip route add" command can
actually remove pre-existing routes if it fails.
(2) Attempt to replace a multipath route results in a broken siblings
linked list. Following commands (like "ip route del") can then either
follow a link into freed memory or end in an infinite loop (if the slab
object has been reused).
v2: fix an omission in first patch
v3: change the semantics of replace operation to better match IPv4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 18 May 2015 18:54:00 +0000 (20:54 +0200)]
ipv6: fix ECMP route replacement
When replacing an IPv6 multipath route with "ip route replace", i.e.
NLM_F_CREATE | NLM_F_REPLACE, fib6_add_rt2node() replaces only first
matching route without fixing its siblings, resulting in corrupted
siblings linked list; removing one of the siblings can then end in an
infinite loop.
IPv6 ECMP implementation is a bit different from IPv4 so that route
replacement cannot work in exactly the same way. This should be a
reasonable approximation:
1. If the new route is ECMP-able and there is a matching ECMP-able one
already, replace it and all its siblings (if any).
2. If the new route is ECMP-able and no matching ECMP-able route exists,
replace first matching non-ECMP-able (if any) or just add the new one.
3. If the new route is not ECMP-able, replace first matching
non-ECMP-able route (if any) or add the new route.
We also need to remove the NLM_F_REPLACE flag after replacing old
route(s) by first nexthop of an ECMP route so that each subsequent
nexthop does not replace previous one.
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Mon, 18 May 2015 18:53:55 +0000 (20:53 +0200)]
ipv6: do not delete previously existing ECMP routes if add fails
If adding a nexthop of an IPv6 multipath route fails, comment in
ip6_route_multipath() says we are going to delete all nexthops already
added. However, current implementation deletes even the routes it
hasn't even tried to add yet. For example, running
ip route add 1234:5678::/64 \
nexthop via fe80::aa dev dummy1 \
nexthop via fe80::bb dev dummy1 \
nexthop via fe80::cc dev dummy1
twice results in removing all routes first command added.
Limit the second (delete) run to nexthops that succeeded in the first
(add) run.
Fixes: 51ebd3181572 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 20 May 2015 11:42:25 +0000 (13:42 +0200)]
Revert "netfilter: bridge: query conntrack about skb dnat"
This reverts commit
c055d5b03bb4cb69d349d787c9787c0383abd8b2.
There are two issues:
'dnat_took_place' made me think that this is related to
-j DNAT/MASQUERADE.
But thats only one part of the story. This is also relevant for SNAT
when we undo snat translation in reverse/reply direction.
Furthermore, I originally wanted to do this mainly to avoid
storing ipv6 addresses once we make DNAT/REDIRECT work
for ipv6 on bridges.
However, I forgot about SNPT/DNPT which is stateless.
So we can't escape storing address for ipv6 anyway. Might as
well do it for ipv4 too.
Reported-and-tested-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dave Jones [Wed, 20 May 2015 00:55:17 +0000 (20:55 -0400)]
netfilter: ensure number of counters is >0 in do_replace()
After improving setsockopt() coverage in trinity, I started triggering
vmalloc failures pretty reliably from this code path:
warn_alloc_failed+0xe9/0x140
__vmalloc_node_range+0x1be/0x270
vzalloc+0x4b/0x50
__do_replace+0x52/0x260 [ip_tables]
do_ipt_set_ctl+0x15d/0x1d0 [ip_tables]
nf_setsockopt+0x65/0x90
ip_setsockopt+0x61/0xa0
raw_setsockopt+0x16/0x60
sock_common_setsockopt+0x14/0x20
SyS_setsockopt+0x71/0xd0
It turns out we don't validate that the num_counters field in the
struct we pass in from userspace is initialized.
The same problem also exists in ebtables, arptables, ipv6, and the
compat variants.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Francesco Ruggeri [Sun, 17 May 2015 21:30:31 +0000 (14:30 -0700)]
netfilter: nfnetlink_{log,queue}: Register pernet in first place
nfnetlink_{log,queue}_init() register the netlink callback nf*_rcv_nl_event
before registering the pernet_subsys, but the callback relies on data
structures allocated by pernet init functions.
When nfnetlink_{log,queue} is loaded, if a netlink message is received after
the netlink callback is registered but before the pernet_subsys is registered,
the kernel will panic in the sequence
nfulnl_rcv_nl_event
nfnl_log_pernet
net_generic
BUG_ON(id == 0) where id is nfnl_log_net_id.
The panic can be easily reproduced in 4.0.3 by:
while true ;do modprobe nfnetlink_log ; rmmod nfnetlink_log ; done &
while true ;do ip netns add dummy ; ip netns del dummy ; done &
This patch moves register_pernet_subsys to earlier in nfnetlink_log_init.
Notice that the BUG_ON hit in 4.0.3 was recently removed in
2591ffd308
["netns: remove BUG_ONs from net_generic()"].
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / firefly-linux-kernel-4.4.55.git / log