Mel Gorman [Tue, 29 May 2012 22:06:19 +0000 (15:06 -0700)]
mm: vmscan: do not stall on writeback during memory compaction
This patch stops reclaim/compaction entering sync reclaim as this was
only intended for lumpy reclaim and an oversight. Page migration has
its own logic for stalling on writeback pages if necessary and memory
compaction is already using it.
Waiting on page writeback is bad for a number of reasons but the primary
one is that waiting on writeback to a slow device like USB can take a
considerable length of time. Page reclaim instead uses
wait_iff_congested() to throttle if too many dirty pages are being
scanned.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Tue, 29 May 2012 22:06:19 +0000 (15:06 -0700)]
mm: vmscan: remove lumpy reclaim
This series removes lumpy reclaim and some stalling logic that was
unintentionally being used by memory compaction. The end result is that
stalling on dirty pages during page reclaim now depends on
wait_iff_congested().
Four kernels were compared
3.3.0 vanilla
3.4.0-rc2 vanilla
3.4.0-rc2 lumpyremove-v2 is patch one from this series
3.4.0-rc2 nosync-v2r3 is the full series
Removing lumpy reclaim saves almost 900 bytes of text whereas the full
series removes 1200 bytes.
text data bss dec hex filename
6740375 1927944 2260992 10929311 a6c49f vmlinux-3.4.0-rc2-vanilla
6739479 1927944 2260992 10928415 a6c11f vmlinux-3.4.0-rc2-lumpyremove-v2
6739159 1927944 2260992 10928095 a6bfdf vmlinux-3.4.0-rc2-nosync-v2
There are behaviour changes in the series and so tests were run with
monitoring of ftrace events. This disrupts results so the performance
results are distorted but the new behaviour should be clearer.
fs-mark running in a threaded configuration showed little of interest as
it did not push reclaim aggressively
FS-Mark Multi Threaded
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Files/s min 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Files/s mean 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Files/s stddev 0.00 ( 0.00%) 0.00 ( 0.00%) 0.00 ( 0.00%) 0.00 ( 0.00%)
Files/s max 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Overhead min 508667.00 ( 0.00%) 521350.00 (-2.49%) 544292.00 (-7.00%) 547168.00 (-7.57%)
Overhead mean 551185.00 ( 0.00%) 652690.73 (-18.42%) 991208.40 (-79.83%) 570130.53 (-3.44%)
Overhead stddev 18200.69 ( 0.00%) 331958.29 (-1723.88%)
1579579.43 (-8578.68%) 9576.81 (47.38%)
Overhead max 576775.00 ( 0.00%)
1846634.00 (-220.17%)
6901055.00 (-1096.49%) 585675.00 (-1.54%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 309.90 300.95 307.33 298.95
User+Sys Time Running Test (seconds) 319.32 309.67 315.69 307.51
Total Elapsed Time (seconds) 1187.85 1193.09 1191.98 1193.73
MMTests Statistics: vmstat
Page Ins 80532 82212 81420 79480
Page Outs
111434984 111456240 111437376 111582628
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 44881 27889 27453 34843
Kswapd pages scanned
25841428 25860774 25861233 25843212
Kswapd pages reclaimed
25841393 25860741 25861199 25843179
Direct pages reclaimed 44881 27889 27453 34843
Kswapd efficiency 99% 99% 99% 99%
Kswapd velocity 21754.791 21675.460 21696.029 21649.127
Direct efficiency 100% 100% 100% 100%
Direct velocity 37.783 23.375 23.031 29.188
Percentage direct scans 0% 0% 0% 0%
ftrace showed that there was no stalling on writeback or pages submitted
for IO from reclaim context.
postmark was similar and while it was more interesting, it also did not
push reclaim heavily.
POSTMARK
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Transactions per second: 16.00 ( 0.00%) 20.00 (25.00%) 18.00 (12.50%) 17.00 ( 6.25%)
Data megabytes read per second: 18.80 ( 0.00%) 24.27 (29.10%) 22.26 (18.40%) 20.54 ( 9.26%)
Data megabytes written per second: 35.83 ( 0.00%) 46.25 (29.08%) 42.42 (18.39%) 39.14 ( 9.24%)
Files created alone per second: 28.00 ( 0.00%) 38.00 (35.71%) 34.00 (21.43%) 30.00 ( 7.14%)
Files create/transact per second: 8.00 ( 0.00%) 10.00 (25.00%) 9.00 (12.50%) 8.00 ( 0.00%)
Files deleted alone per second: 556.00 ( 0.00%) 1224.00 (120.14%) 3062.00 (450.72%) 6124.00 (1001.44%)
Files delete/transact per second: 8.00 ( 0.00%) 10.00 (25.00%) 9.00 (12.50%) 8.00 ( 0.00%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 113.34 107.99 109.73 108.72
User+Sys Time Running Test (seconds) 145.51 139.81 143.32 143.55
Total Elapsed Time (seconds) 1159.16 899.23 980.17 1062.27
MMTests Statistics: vmstat
Page Ins
13710192 13729032 13727944 13760136
Page Outs
43071140 42987228 42733684 42931624
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 0 0 0 0
Kswapd pages scanned
9941613 9937443 9939085 9929154
Kswapd pages reclaimed
9940926 9936751 9938397 9928465
Direct pages reclaimed 0 0 0 0
Kswapd efficiency 99% 99% 99% 99%
Kswapd velocity 8576.567 11051.058 10140.164 9347.109
Direct efficiency 100% 100% 100% 100%
Direct velocity 0.000 0.000 0.000 0.000
It looks like here that the full series regresses performance but as
ftrace showed no usage of wait_iff_congested() or sync reclaim I am
assuming it's a disruption due to monitoring. Other data such as memory
usage, page IO, swap IO all looked similar.
Running a benchmark with a plain DD showed nothing very interesting.
The full series stalled in wait_iff_congested() slightly less but stall
times on vanilla kernels were marginal.
Running a benchmark that hammered on file-backed mappings showed stalls
due to congestion but not in sync writebacks
MICRO
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
MMTests Statistics: duration
Sys Time Running Test (seconds) 308.13 294.50 298.75 299.53
User+Sys Time Running Test (seconds) 330.45 316.28 318.93 320.79
Total Elapsed Time (seconds) 1814.90 1833.88 1821.14 1832.91
MMTests Statistics: vmstat
Page Ins 108712 120708 97224 110344
Page Outs
155514576 156017404 155813676 156193256
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned
2599253 1550480 2512822 2414760
Kswapd pages scanned
69742364 71150694 68839041 69692533
Kswapd pages reclaimed
34824488 34773341 34796602 34799396
Direct pages reclaimed 53693 94750 61792 75205
Kswapd efficiency 49% 48% 50% 49%
Kswapd velocity 38427.662 38797.901 37799.972 38022.889
Direct efficiency 2% 6% 2% 3%
Direct velocity 1432.174 845.464 1379.807 1317.446
Percentage direct scans 3% 2% 3% 3%
Page writes by reclaim 0 0 0 0
Page writes file 0 0 0 0
Page writes anon 0 0 0 0
Page reclaim immediate 0 0 0 1218
Page rescued immediate 0 0 0 0
Slabs scanned 15360 16384 13312 16384
Direct inode steals 0 0 0 0
Kswapd inode steals 4340 4327 1630 4323
FTrace Reclaim Statistics: congestion_wait
Direct number congest waited 0 0 0 0
Direct time congest waited 0ms 0ms 0ms 0ms
Direct full congest waited 0 0 0 0
Direct number conditional waited 900 870 754 789
Direct time conditional waited 0ms 0ms 0ms 20ms
Direct full conditional waited 0 0 0 0
KSwapd number congest waited 2106 2308 2116 1915
KSwapd time congest waited 139924ms 157832ms 125652ms 132516ms
KSwapd full congest waited 1346 1530 1202 1278
KSwapd number conditional waited 12922 16320 10943 14670
KSwapd time conditional waited 0ms 0ms 0ms 0ms
KSwapd full conditional waited 0 0 0 0
Reclaim statistics are not radically changed. The stall times in kswapd
are massive but it is clear that it is due to calls to congestion_wait()
and that is almost certainly the call in balance_pgdat(). Otherwise
stalls due to dirty pages are non-existant.
I ran a benchmark that stressed high-order allocation. This is very
artifical load but was used in the past to evaluate lumpy reclaim and
compaction. Generally I look at allocation success rates and latency
figures.
STRESS-HIGHALLOC
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Pass 1 81.00 ( 0.00%) 28.00 (-53.00%) 24.00 (-57.00%) 28.00 (-53.00%)
Pass 2 82.00 ( 0.00%) 39.00 (-43.00%) 38.00 (-44.00%) 43.00 (-39.00%)
while Rested 88.00 ( 0.00%) 87.00 (-1.00%) 88.00 ( 0.00%) 88.00 ( 0.00%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 740.93 681.42 685.14 684.87
User+Sys Time Running Test (seconds) 2922.65 3269.52 3281.35 3279.44
Total Elapsed Time (seconds) 1161.73 1152.49 1159.55 1161.44
MMTests Statistics: vmstat
Page Ins
4486020 2807256 2855944 2876244
Page Outs
7261600 7973688 7975320 7986120
Swap Ins 31694 0 0 0
Swap Outs 98179 0 0 0
Direct pages scanned 53494 57731 34406 113015
Kswapd pages scanned
6271173 1287481 1278174 1219095
Kswapd pages reclaimed
2029240 1281025 1260708 1201583
Direct pages reclaimed 1468 14564 16649 92456
Kswapd efficiency 32% 99% 98% 98%
Kswapd velocity 5398.133 1117.130 1102.302 1049.641
Direct efficiency 2% 25% 48% 81%
Direct velocity 46.047 50.092 29.672 97.306
Percentage direct scans 0% 4% 2% 8%
Page writes by reclaim
1616049 0 0 0
Page writes file
1517870 0 0 0
Page writes anon 98179 0 0 0
Page reclaim immediate 103778 27339 9796 17831
Page rescued immediate 0 0 0 0
Slabs scanned
1096704 986112 980992 998400
Direct inode steals 223 215040 216736 247881
Kswapd inode steals 175331 61548 68444 63066
Kswapd skipped wait 21991 0 1 0
THP fault alloc 1 135 125 134
THP collapse alloc 393 311 228 236
THP splits 25 13 7 8
THP fault fallback 0 0 0 0
THP collapse fail 3 5 7 7
Compaction stalls 865 1270 1422 1518
Compaction success 370 401 353 383
Compaction failures 495 869 1069 1135
Compaction pages moved 870155
3828868 4036106 4423626
Compaction move failure 26429 23865 29742 27514
Success rates are completely hosed for 3.4-rc2 which is almost certainly
due to commit
fe2c2a106663 ("vmscan: reclaim at order 0 when compaction
is enabled"). I expected this would happen for kswapd and impair
allocation success rates (https://lkml.org/lkml/2012/1/25/166) but I did
not anticipate this much a difference: 80% less scanning, 37% less
reclaim by kswapd
In comparison, reclaim/compaction is not aggressive and gives up easily
which is the intended behaviour. hugetlbfs uses __GFP_REPEAT and would
be much more aggressive about reclaim/compaction than THP allocations
are. The stress test above is allocating like neither THP or hugetlbfs
but is much closer to THP.
Mainline is now impaired in terms of high order allocation under heavy
load although I do not know to what degree as I did not test with
__GFP_REPEAT. Keep this in mind for bugs related to hugepage pool
resizing, THP allocation and high order atomic allocation failures from
network devices.
In terms of congestion throttling, I see the following for this test
FTrace Reclaim Statistics: congestion_wait
Direct number congest waited 3 0 0 0
Direct time congest waited 0ms 0ms 0ms 0ms
Direct full congest waited 0 0 0 0
Direct number conditional waited 957 512 1081 1075
Direct time conditional waited 0ms 0ms 0ms 0ms
Direct full conditional waited 0 0 0 0
KSwapd number congest waited 36 4 3 5
KSwapd time congest waited 3148ms 400ms 300ms 500ms
KSwapd full congest waited 30 4 3 5
KSwapd number conditional waited 88514 197 332 542
KSwapd time conditional waited 4980ms 0ms 0ms 0ms
KSwapd full conditional waited 49 0 0 0
The "conditional waited" times are the most interesting as this is
directly impacted by the number of dirty pages encountered during scan.
As lumpy reclaim is no longer scanning contiguous ranges, it is finding
fewer dirty pages. This brings wait times from about 5 seconds to 0.
kswapd itself is still calling congestion_wait() so it'll still stall but
it's a lot less.
In terms of the type of IO we were doing, I see this
FTrace Reclaim Statistics: mm_vmscan_writepage
Direct writes anon sync 0 0 0 0
Direct writes anon async 0 0 0 0
Direct writes file sync 0 0 0 0
Direct writes file async 0 0 0 0
Direct writes mixed sync 0 0 0 0
Direct writes mixed async 0 0 0 0
KSwapd writes anon sync 0 0 0 0
KSwapd writes anon async 91682 0 0 0
KSwapd writes file sync 0 0 0 0
KSwapd writes file async 822629 0 0 0
KSwapd writes mixed sync 0 0 0 0
KSwapd writes mixed async 0 0 0 0
In 3.2, kswapd was doing a bunch of async writes of pages but
reclaim/compaction was never reaching a point where it was doing sync
IO. This does not guarantee that reclaim/compaction was not calling
wait_on_page_writeback() but I would consider it unlikely. It indicates
that merging patches 2 and 3 to stop reclaim/compaction calling
wait_on_page_writeback() should be safe.
This patch:
Lumpy reclaim had a purpose but in the mind of some, it was to kick the
system so hard it trashed. For others the purpose was to complicate
vmscan.c. Over time it was giving softer shoes and a nicer attitude but
memory compaction needs to step up and replace it so this patch sends
lumpy reclaim to the farm.
The tracepoint format changes for isolating LRU pages with this patch
applied. Furthermore reclaim/compaction can no longer queue dirty pages
in pageout() if the underlying BDI is congested. Lumpy reclaim used
this logic and reclaim/compaction was using it in error.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Tue, 29 May 2012 22:06:18 +0000 (15:06 -0700)]
mm: remove swap token code
The swap token code no longer fits in with the current VM model. It
does not play well with cgroups or the better NUMA placement code in
development, since we have only one swap token globally.
It also has the potential to mess with scalability of the system, by
increasing the number of non-reclaimable pages on the active and
inactive anon LRU lists.
Last but not least, the swap token code has been broken for a year
without complaints, as reported by Konstantin Khlebnikov. This suggests
we no longer have much use for it.
The days of sub-1G memory systems with heavy use of swap are over. If
we ever need thrashing reducing code in the future, we will have to
implement something that does scale.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Bob Picco <bpicco@meloft.net>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Tue, 29 May 2012 22:06:17 +0000 (15:06 -0700)]
mm, thp: allow fallback when pte_alloc_one() fails for huge pmd
The transparent hugepages feature is careful to not invoke the oom
killer when a hugepage cannot be allocated.
pte_alloc_one() failing in __do_huge_pmd_anonymous_page(), however,
currently results in VM_FAULT_OOM which invokes the pagefault oom killer
to kill a memory-hogging task.
This is unnecessary since it's possible to drop the reference to the
hugepage and fallback to allocating a small page.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Tue, 29 May 2012 22:06:17 +0000 (15:06 -0700)]
mm, thp: remove unnecessary ret variable
The "ret" variable is unnecessary in __do_huge_pmd_anonymous_page(), so
remove it.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wang Sheng-Hui [Tue, 29 May 2012 22:06:17 +0000 (15:06 -0700)]
mm/hugetlb.c: use long vars instead of int in region_count()
The arguments f & t and fields from & to of struct file_region are
defined as long. So use long instead of int to type the temp vars.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wang Sheng-Hui [Tue, 29 May 2012 22:06:16 +0000 (15:06 -0700)]
mm/mempolicy.c: use enum value MPOL_REBIND_ONCE in mpol_rebind_policy()
We have enum definition in mempolicy.h: MPOL_REBIND_ONCE. It should
replace the magic number 0 for step comparison in function
mpol_rebind_policy.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Borislav Petkov [Tue, 29 May 2012 22:06:16 +0000 (15:06 -0700)]
mm/memory_failure: let the compiler add the function name
These things tend to get out of sync with time so let the compiler
automatically enter the current function name using __func__.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Andi Kleen <andi@firstfloor.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sasha Levin [Tue, 29 May 2012 22:06:15 +0000 (15:06 -0700)]
mm: fix NULL ptr deref when walking hugepages
A missing validation of the value returned by find_vma() could cause a
NULL ptr dereference when walking the pagetable.
This is triggerable from usermode by a simple user by trying to read a
page info out of /proc/pid/pagemap which doesn't exist.
Introduced by commit
025c5b2451e4 ("thp: optimize away unnecessary page
table locking").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.4.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cong Wang [Tue, 29 May 2012 22:06:15 +0000 (15:06 -0700)]
cris: select GENERIC_ATOMIC64
Cris doesn't implement atomic64 operations neither, should select
GENERIC_ATOMIC64.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Gortmaker [Tue, 29 May 2012 22:06:14 +0000 (15:06 -0700)]
pagemap.h: fix warning about possibly used before init var
Commit
f56f821feb7b ("mm: extend prefault helpers to fault in more than
PAGE_SIZE") added in the new functions: fault_in_multipages_writeable()
and fault_in_multipages_readable().
However, we currently see:
include/linux/pagemap.h:492: warning: 'ret' may be used uninitialized in this function
include/linux/pagemap.h:492: note: 'ret' was declared here
Unlike a lot of gcc nags, this one appears somewhat legit. i.e. passing
in an invalid negative value of "size" does make it look like all the
conditionals in there would be bypassed and the uninitialized value would
be returned.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 29 May 2012 18:53:11 +0000 (11:53 -0700)]
Merge tag 'mfd-3.5-1' of git://git./linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
Linus Torvalds [Tue, 29 May 2012 17:43:51 +0000 (10:43 -0700)]
Merge tag 'nfs-for-3.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"New features include:
- Rewrite the O_DIRECT code so that it can share the same coalescing
and pNFS functionality as the page cache code.
- Allow the server to provide hints as to when we should use pNFS,
and when it is more efficient to read and write through the
metadata server.
- NFS cache consistency updates:
* Use the ctime to emulate a change attribute for NFSv2/v3 so that
all NFS versions can share the same cache management code.
* New cache management code will only look at the change attribute
and size attribute when deciding whether or not our cached data
is still valid or not.
* Don't request NFSv4 post-op attributes on writes in cases such as
O_DIRECT, where we don't care about data cache consistency, or
when we have a write delegation, and know that our cache is still
consistent.
* Don't request NFSv4 post-op attributes on operations such as
COMMIT, where there are no expected metadata updates.
* Don't request NFSv4 directory post-op attributes in cases where
the operations themselves already return change attribute
updates: i.e. operations such as OPEN, CREATE, REMOVE, LINK and
RENAME.
- Speed up 'ls' and friends by using READDIR rather than READDIRPLUS
if we detect no attempts to lookup filenames.
- Improve the code sharing between NFSv2/v3 and v4 mounts
- NFSv4.1 state management efficiency improvements
- More patches in preparation for NFSv4/v4.1 migration functionality."
Fix trivial conflict in fs/nfs/nfs4proc.c that was due to the dcache
qstr name initialization changes (that made the length/hash a 64-bit
union)
* tag 'nfs-for-3.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (146 commits)
NFSv4: Add debugging printks to state manager
NFSv4: Map NFS4ERR_SHARE_DENIED into an EACCES error instead of EIO
NFSv4: update_changeattr does not need to set NFS_INO_REVAL_PAGECACHE
NFSv4.1: nfs4_reset_session should use nfs4_handle_reclaim_lease_error
NFSv4.1: Handle other occurrences of NFS4ERR_CONN_NOT_BOUND_TO_SESSION
NFSv4.1: Handle NFS4ERR_CONN_NOT_BOUND_TO_SESSION in the state manager
NFSv4.1: Handle errors in nfs4_bind_conn_to_session
NFSv4.1: nfs4_bind_conn_to_session should drain the session
NFSv4.1: Don't clobber the seqid if exchange_id returns a confirmed clientid
NFSv4.1: Add DESTROY_CLIENTID
NFSv4.1: Ensure we use the correct credentials for bind_conn_to_session
NFSv4.1: Ensure we use the correct credentials for session create/destroy
NFSv4.1: Move NFSPROC4_CLNT_BIND_CONN_TO_SESSION to the end of the operations
NFSv4.1: Handle NFS4ERR_SEQ_MISORDERED when confirming the lease
NFSv4: When purging the lease, we must clear NFS4CLNT_LEASE_CONFIRM
NFSv4: Clean up the error handling for nfs4_reclaim_lease
NFSv4.1: Exchange ID must use GFP_NOFS allocation mode
nfs41: Use BIND_CONN_TO_SESSION for CB_PATH_DOWN*
nfs4.1: add BIND_CONN_TO_SESSION operation
NFSv4.1 test the mdsthreshold hint parameters
...
Alan Cox [Tue, 29 May 2012 12:45:16 +0000 (13:45 +0100)]
tty: fix ldisc lock inversion trace
This is caused by tty_release using tty_lock_pair to lock both sides of
the pty/tty pair, and then tty_ldisc_release dropping and relocking one
side only. We can drop both fine, so drop both to avoid any lock
ordering concerns.
Rework the release path to fix the new locking model.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 29 May 2012 12:45:01 +0000 (13:45 +0100)]
pty: Fix lock inversion
The ptmx_open path takes the tty and devpts locks in the wrong order
because tty_init_dev locks and returns a locked tty. As far as I can
tell this is actually safe anyway because the tty being returned is new
so nobody can get a reference to lock it at this point.
However we don't even need the devpts lock at this point, it's only held
as a byproduct of the way the locks were pushe down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trond Myklebust [Mon, 28 May 2012 19:12:27 +0000 (15:12 -0400)]
NFSv4: Add debugging printks to state manager
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Mon, 28 May 2012 15:36:28 +0000 (11:36 -0400)]
NFSv4: Map NFS4ERR_SHARE_DENIED into an EACCES error instead of EIO
If a file OPEN is denied due to a share lock, the resulting
NFS4ERR_SHARE_DENIED is currently mapped to the default EIO.
This patch adds a more appropriate mapping, and brings Linux
into line with what Solaris 10 does.
See https://bugzilla.kernel.org/show_bug.cgi?id=43286
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
Linus Torvalds [Mon, 28 May 2012 20:10:41 +0000 (13:10 -0700)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
Pull exofs updates from Boaz Harrosh:
"Just a couple of patches. The first is a BUG fix destined for stable
which missed the 3.4-rc7 Kernel. The second is just a fixture
addition so exofs is able to be better exported as a cluster file
system via pNFS."
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: Add SYSFS info for autologin/pNFS export
exofs: Fix CRASH on very early IO errors.
Linus Torvalds [Mon, 28 May 2012 17:40:11 +0000 (10:40 -0700)]
Merge branch 'doc' of git://git./linux/kernel/git/jikos/trivial
Pull documentation updates from Jiri Kosina:
"I am currently relaying documentation patches through 'doc' branch of
trivial tree, until Rob, the new documentation maintainer, has
established a proper tree."
* 'doc' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
doc: ext3: update documentation with barrier=1 default
Documentation/initrd.txt: Change the location of util-linux
Documentation/SubmittingPatches: suggested the use of scripts/get_maintainer.pl
Documentation/kernel-parameters: remove autotest and mcatest
Linus Torvalds [Mon, 28 May 2012 17:39:07 +0000 (10:39 -0700)]
Merge branch 'misc' of git://git./linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"The non-critical part of kbuild for 3.5 includes
- two new coccinelle checks
- fix for make deb-pkg to include generated headers in arch/*/include
I have more make-deb-pkg fixes in the backlog, but these will likely
have to wait for 3.6."
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
builddeb: include autogenerated header files
scripts/coccinelle: sizeof of pointer
scripts/coccinelle: address test is always true
Linus Torvalds [Mon, 28 May 2012 17:37:56 +0000 (10:37 -0700)]
Merge branch 'kconfig' of git://git./linux/kernel/git/mmarek/kbuild
Pull kconfig changes from Michal Marek:
- Error handling for make KCONFIG_ALLCONFIG=<...> all*config plus a fix
for a bug that was exposed by this
- Fix for the script/config utility.
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/config: properly report and set string options
kbuild: all{no,yes,mod,def,rand}config only read files when instructed to.
kconfig: Add error handling to KCONFIG_ALLCONFIG
Linus Torvalds [Mon, 28 May 2012 17:32:28 +0000 (10:32 -0700)]
Merge branch 'kbuild' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek.
Fixed up nontrivial merge conflict in Makefile as per Stephen Rothwell
and linux-next (and trivial arch/sparc/Makefile changes due to removed
sparc32 logic).
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
mips: Fix KBUILD_CPPFLAGS definition
kbuild: fix ia64 link
kbuild: document KBUILD_LDS, KBUILD_VMLINUX_{INIT,MAIN} and LDFLAGS_vmlinux
kbuild: link of vmlinux moved to a script
kbuild: refactor final link of sparc32
kbuild: drop unused KBUILD_VMLINUX_OBJS from top-level Makefile
kbuild: Makefile: remove unnecessary check for m68knommu ARCH
Linus Torvalds [Mon, 28 May 2012 16:54:45 +0000 (09:54 -0700)]
Merge tag 'writeback' of git://git./linux/kernel/git/wfg/linux
Pull writeback tree from Wu Fengguang:
"Mainly from Jan Kara to avoid iput() in the flusher threads."
* tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Avoid iput() from flusher thread
vfs: Rename end_writeback() to clear_inode()
vfs: Move waiting for inode writeback from end_writeback() to evict_inode()
writeback: Refactor writeback_single_inode()
writeback: Remove wb->list_lock from writeback_single_inode()
writeback: Separate inode requeueing after writeback
writeback: Move I_DIRTY_PAGES handling
writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()
writeback: Move clearing of I_SYNC into inode_sync_complete()
writeback: initialize global_dirty_limit
fs: remove 8 bytes of padding from struct writeback_control on 64 bit builds
mm: page-writeback.c: local functions should not be exposed globally
Linus Torvalds [Mon, 28 May 2012 16:49:56 +0000 (09:49 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze changes from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Setup correct pointer to TLS area
microblaze: Add TLS support to sys_clone
microblaze: ftrace: Pass the first calling instruction for dynamic ftrace
microblaze: Port OOM changes to do_page_fault
microblaze: Do not select GENERIC_GPIO by default
Trond Myklebust [Mon, 28 May 2012 14:01:34 +0000 (10:01 -0400)]
NFSv4: update_changeattr does not need to set NFS_INO_REVAL_PAGECACHE
We're already invalidating the data cache, and setting the new change
attribute. Since directories don't care about the i_size field, there
is no need to be forcing any extra revalidation of the page cache.
We do keep the NFS_INO_INVALID_ATTR flag, in order to force an
attribute cache revalidation on stat() calls since we do not
update the mtime and ctime fields.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Jonas Bonn [Sun, 27 May 2012 08:25:47 +0000 (10:25 +0200)]
openrisc: use generic strnlen_user() function
The generic version is both easier to support and more correct.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mackerras [Mon, 28 May 2012 03:03:47 +0000 (13:03 +1000)]
powerpc: Use the new generic strncpy_from_user() and strnlen_user()
This is much the same as for SPARC except that we can do the find_zero()
function more efficiently using the count-leading-zeroes instructions.
Tested on 32-bit and 64-bit PowerPC.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mackerras [Mon, 28 May 2012 02:59:56 +0000 (12:59 +1000)]
lib: Fix generic strnlen_user for 32-bit big-endian machines
The aligned_byte_mask() definition is wrong for 32-bit big-endian
machines: the "7-(n)" part of the definition assumes a long is 8
bytes. This fixes it by using BITS_PER_LONG - 8 instead of 8*7.
Tested on 32-bit and 64-bit PowerPC.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trond Myklebust [Sun, 27 May 2012 18:46:46 +0000 (14:46 -0400)]
NFSv4.1: nfs4_reset_session should use nfs4_handle_reclaim_lease_error
The results from a call to nfs4_proc_create_session() should always
be fed into nfs4_handle_reclaim_lease_error, so that we can
handle errors such as NFS4ERR_SEQ_MISORDERED correctly.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sun, 27 May 2012 17:02:53 +0000 (13:02 -0400)]
NFSv4.1: Handle other occurrences of NFS4ERR_CONN_NOT_BOUND_TO_SESSION
Let nfs4_schedule_session_recovery() handle the details of choosing
between resetting the session, and other session related recovery.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sun, 27 May 2012 16:58:48 +0000 (12:58 -0400)]
NFSv4.1: Handle NFS4ERR_CONN_NOT_BOUND_TO_SESSION in the state manager
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sun, 27 May 2012 16:53:10 +0000 (12:53 -0400)]
NFSv4.1: Handle errors in nfs4_bind_conn_to_session
Ensure that we handle NFS4ERR_DELAY errors separately, and then
let nfs4_recovery_handle_error() handle all other cases.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Sun, 27 May 2012 17:47:21 +0000 (13:47 -0400)]
NFSv4.1: nfs4_bind_conn_to_session should drain the session
In order to avoid races with other RPC calls that end up setting the
NFS4CLNT_BIND_CONN_TO_SESSION flag.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Sat, 26 May 2012 23:57:16 +0000 (16:57 -0700)]
Merge branch 'generic-string-functions'
This makes <asm/word-at-a-time.h> actually live up to its promise of
allowing architectures to help tune the string functions that do their
work a word at a time.
David had already taken the x86 strncpy_from_user() function, modified
it to work on sparc, and then done the extra work to make it generically
useful. This then expands on that work by making x86 use that generic
version, completing the circle.
But more importantly, it fixes up the word-at-a-time interfaces so that
it's now easy to also support things like strnlen_user(), and pretty
much most random string functions.
David reports that it all works fine on sparc, and Jonas Bonn reported
that an earlier version of this worked on OpenRISC too. It's pretty
easy for architectures to add support for this and just replace their
private versions with the generic code.
* generic-string-functions:
sparc: use the new generic strnlen_user() function
x86: use the new generic strnlen_user() function
lib: add generic strnlen_user() function
word-at-a-time: make the interfaces truly generic
x86: use generic strncpy_from_user routine
Lekensteyn [Fri, 18 May 2012 08:22:43 +0000 (10:22 +0200)]
builddeb: include autogenerated header files
After
303395ac3bf3e2cb488435537d416bc840438fcb, some headers are
autogenerated. Include these autogenerated headers (mainly
unistd_32_ia32.h) in out-of-tree builds to allow DKMS modules to be
built succesfully.
Signed-off-by: Peter Lekensteyn <lekensteyn@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Linus Torvalds [Sat, 26 May 2012 20:35:03 +0000 (13:35 -0700)]
Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux
Pull i2c-embedded changes from Wolfram Sang:
"Major changes:
- lots of devicetree additions for existing drivers. I tried hard to
make sure the bindings are proper. In more complicated cases, I
requested acks from people having more experience with them than
me. That took a bit of extra time and also some time went into
discussions with developers about what bindings are and what not.
I have the feeling that the workflow with bindings should be
improved to scale better. I will spend some more thought on
this...
- i2c-muxes are succesfully used meanwhile, so we dropped
EXPERIMENTAL for them and renamed the drivers to a standard pattern
to match the rest of the subsystem. They can also be used with
devicetree now.
- ixp2000 was removed since the whole platform goes away.
- cleanups (strlcpy instead of strcpy, NULL instead of 0)
- The rest is typical driver fixes I assume.
All patches have been in linux-next at least since v3.4-rc6."
Fixed up trivial conflict in arch/arm/mach-lpc32xx/common.c due to the
same patch already having come in through the arm/soc trees, with
additional patches on top of it.
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (35 commits)
i2c: davinci: Free requested IRQ in remove
i2c: ocores: register OF i2c devices
i2c: tegra: notify transfer-complete after clearing status.
I2C: xiic: Add OF binding support
i2c: Rename last mux driver to standard pattern
i2c: tegra: fix 10bit address configuration
i2c: muxes: rename first set of drivers to a standard pattern
of/i2c: implement of_find_i2c_adapter_by_node
i2c: implement i2c_verify_adapter
i2c-s3c2410: Add HDMIPHY quirk for S3C2440
i2c-s3c2410: Rework device type handling
i2c: muxes are not EXPERIMENTAL anymore
i2c/of: Automatically populate i2c mux busses from device tree data.
i2c: Add a struct device * parameter to i2c_add_mux_adapter()
of/i2c: call i2c_verify_client from of_find_i2c_device_by_node
i2c: designware: Add clk_{un}prepare() support
i2c: designware: add PM support
i2c: ixp2000: remove driver
i2c: pnx: add device tree support
i2c: imx: don't use strcpy but strlcpy
...
Linus Torvalds [Sat, 26 May 2012 20:14:01 +0000 (13:14 -0700)]
Merge tag 'cleanup-initcall' of git://git./linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
Linus Torvalds [Sat, 26 May 2012 20:05:55 +0000 (13:05 -0700)]
Merge tag 'soc2' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d687 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit
f10590c9836c ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
Linus Torvalds [Sat, 26 May 2012 19:57:47 +0000 (12:57 -0700)]
Merge tag 'dt2' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
Linus Torvalds [Sat, 26 May 2012 19:50:04 +0000 (12:50 -0700)]
Merge tag 'stmp-dev' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc stmp-dev library code from Olof Johansson:
"A number of devices are using a common register layout, this adds
support code for it in lib/stmp_device.c so we do not need to
duplicate it in each driver."
Fix up trivial conflicts in drivers/i2c/busses/i2c-mxs.c and
lib/Makefile
* tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
i2c: mxs: use global reset function
lib: add support for stmp-style devices
Linus Torvalds [Sat, 26 May 2012 19:42:29 +0000 (12:42 -0700)]
Merge tag 'clock' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Linus Torvalds [Sat, 26 May 2012 19:31:49 +0000 (12:31 -0700)]
Merge tag 'cleanup2' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf5c: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
Linus Torvalds [Sat, 26 May 2012 19:22:27 +0000 (12:22 -0700)]
Merge tag 'drivers' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
Linus Torvalds [Sat, 26 May 2012 19:19:31 +0000 (12:19 -0700)]
Merge tag 'defconfig' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc defconfig updates from Olof Johansson:
"For the first time, we have one branch that collects just updates to
defconfig files, mostly for adapting to changes in other subsystems."
* tag 'defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PRIMA2: add prima2_defconfig for CSR SiRFprimaII
ARM: tegra: update defconfig
ARM: tegra: update defconfig
ARM: imx_v6_v7_defconfig: Add SPI NOR support
ARM: imx_v4_v5_defconfig: Let CONFIG_MACH_IMX27_DT be built by default
David Miller [Sat, 26 May 2012 18:14:27 +0000 (11:14 -0700)]
sparc: use the new generic strnlen_user() function
This throws away the sparc-specific functions in favor of the generic
optimized version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 26 May 2012 18:09:53 +0000 (11:09 -0700)]
x86: use the new generic strnlen_user() function
This throws away the old x86-specific functions in favor of the generic
optimized version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 26 May 2012 18:06:38 +0000 (11:06 -0700)]
lib: add generic strnlen_user() function
This adds a new generic optimized strnlen_user() function that uses the
<asm/word-at-a-time.h> infrastructure to portably do efficient string
handling.
In many ways, strnlen is much simpler than strncpy, and in particular we
can always pre-align the words we load from memory. That means that all
the worries about alignment etc are a non-issue, so this one can easily
be used on any architecture. You obviously do have to do the
appropriate word-at-a-time.h macros.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 26 May 2012 17:43:17 +0000 (10:43 -0700)]
word-at-a-time: make the interfaces truly generic
This changes the interfaces in <asm/word-at-a-time.h> to be a bit more
complicated, but a lot more generic.
In particular, it allows us to really do the operations efficiently on
both little-endian and big-endian machines, pretty much regardless of
machine details. For example, if you can rely on a fast population
count instruction on your architecture, this will allow you to make your
optimized <asm/word-at-a-time.h> file with that.
NOTE! The "generic" version in include/asm-generic/word-at-a-time.h is
not truly generic, it actually only works on big-endian. Why? Because
on little-endian the generic algorithms are wasteful, since you can
inevitably do better. The x86 implementation is an example of that.
(The only truly non-generic part of the asm-generic implementation is
the "find_zero()" function, and you could make a little-endian version
of it. And if the Kbuild infrastructure allowed us to pick a particular
header file, that would be lovely)
The <asm/word-at-a-time.h> functions are as follows:
- WORD_AT_A_TIME_CONSTANTS: specific constants that the algorithm
uses.
- has_zero(): take a word, and determine if it has a zero byte in it.
It gets the word, the pointer to the constant pool, and a pointer to
an intermediate "data" field it can set.
This is the "quick-and-dirty" zero tester: it's what is run inside
the hot loops.
- "prep_zero_mask()": take the word, the data that has_zero() produced,
and the constant pool, and generate an *exact* mask of which byte had
the first zero. This is run directly *outside* the loop, and allows
the "has_zero()" function to answer the "is there a zero byte"
question without necessarily getting exactly *which* byte is the
first one to contain a zero.
If you do multiple byte lookups concurrently (eg "hash_name()", which
looks for both NUL and '/' bytes), after you've done the prep_zero_mask()
phase, the result of those can be or'ed together to get the "either
or" case.
- The result from "prep_zero_mask()" can then be fed into "find_zero()"
(to find the byte offset of the first byte that was zero) or into
"zero_bytemask()" (to find the bytemask of the bytes preceding the
zero byte).
The existence of zero_bytemask() is optional, and is not necessary
for the normal string routines. But dentry name hashing needs it, so
if you enable DENTRY_WORD_AT_A_TIME you need to expose it.
This changes the generic strncpy_from_user() function and the dentry
hashing functions to use these modified word-at-a-time interfaces. This
gets us back to the optimized state of the x86 strncpy that we lost in
the previous commit when moving over to the generic version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trond Myklebust [Sat, 26 May 2012 17:41:04 +0000 (13:41 -0400)]
NFSv4.1: Don't clobber the seqid if exchange_id returns a confirmed clientid
If the EXCHGID4_FLAG_CONFIRMED_R flag is set, the client is in theory
supposed to already know the correct value of the seqid, in which case
RFC5661 states that it should ignore the value returned.
Also ensure that if the sanity check in nfs4_check_cl_exchange_flags
fails, then we must not change the nfs_client fields.
Finally, clean up the code: we don't need to retest the value of
'status' unless it can change.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Fri, 25 May 2012 21:18:09 +0000 (17:18 -0400)]
NFSv4.1: Add DESTROY_CLIENTID
Ensure that we destroy our lease on last unmount
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Sat, 26 May 2012 17:14:39 +0000 (10:14 -0700)]
x86: use generic strncpy_from_user routine
The generic strncpy_from_user() is not really optimal, since it is
designed to work on both little-endian and big-endian. And on
little-endian you can simplify much of the logic to find the first zero
byte, since little-endian arithmetic doesn't have to worry about the
carry bit propagating into earlier bytes (only later bytes, which we
don't care about).
But I have patches to make the generic routines use the architecture-
specific <asm/word-at-a-time.h> infrastructure, so that we can regain
the little-endian optimizations. But before we do that, switch over to
the generic routines to make the patches each do just one well-defined
thing.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 25 May 2012 23:14:12 +0000 (16:14 -0700)]
Merge tag 'x86-mce-merge' of git://git./linux/kernel/git/ras/ras
Pull x86/mce merge window patches from Tony Luck:
"Including two that make error_context() checks less sucky"
* tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Add instruction recovery signatures to mce-severity table
x86/mce: Fix check for processor context when machine check was taken.
MCE: Fix vm86 handling for 32bit mce handler
x86/mce Add validation check before GHES error is recorded
x86/mce: Avoid reading every machine check bank register twice.
Linus Torvalds [Fri, 25 May 2012 22:59:38 +0000 (15:59 -0700)]
Merge git://git./linux/kernel/git/cmetcalf/linux-tile
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
David Woodhouse [Fri, 25 May 2012 16:43:02 +0000 (17:43 +0100)]
intel-iommu: Move duplicate list-mangling code into unlink_domain_info() helper
Now we have four copies of this code, Linus "suggested" it was about time
we stopped copying it and turned it into a helper.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Woodhouse [Fri, 25 May 2012 16:42:54 +0000 (17:42 +0100)]
intel-iommu: Add device info into list before doing context mapping
Add device info into list before doing context mapping, because device
info will be used by iommu_enable_dev_iotlb(). Without it, ATS won't get
enabled as it should be.
ATS, while a dubious decision from a security point of view, can be very
important for performance.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trond Myklebust [Fri, 25 May 2012 21:57:41 +0000 (17:57 -0400)]
NFSv4.1: Ensure we use the correct credentials for bind_conn_to_session
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Weston Andros Adamson <dros@netapp.com>
Trond Myklebust [Fri, 25 May 2012 21:51:23 +0000 (17:51 -0400)]
NFSv4.1: Ensure we use the correct credentials for session create/destroy
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Fri, 25 May 2012 21:11:42 +0000 (17:11 -0400)]
NFSv4.1: Move NFSPROC4_CLNT_BIND_CONN_TO_SESSION to the end of the operations
For backward compatibility with nfs-utils.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Weston Andros Adamson <dros@netapp.com>
Trond Myklebust [Fri, 25 May 2012 19:00:06 +0000 (15:00 -0400)]
NFSv4.1: Handle NFS4ERR_SEQ_MISORDERED when confirming the lease
Apparently the patch "NFS: Always use the same SETCLIENTID boot verifier"
is tickling a Linux nfs server bug, and causing a regression: the server
can get into a situation where it keeps replying NFS4ERR_SEQ_MISORDERED
to our CREATE_SESSION request even when we are sending the correct
sequence ID.
Fix this by purging the lease and then retrying.
Reported-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Fri, 25 May 2012 20:02:15 +0000 (16:02 -0400)]
NFSv4: When purging the lease, we must clear NFS4CLNT_LEASE_CONFIRM
Otherwise we can end up not sending a new exchange-id/setclientid
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Fri, 25 May 2012 19:00:06 +0000 (15:00 -0400)]
NFSv4: Clean up the error handling for nfs4_reclaim_lease
Try to consolidate the error handling for nfs4_reclaim_lease into
a single function instead of doing a bit here, and a bit there...
Also ensure that NFS4CLNT_PURGE_STATE handles errors correctly.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chris Metcalf [Sun, 20 May 2012 19:15:34 +0000 (15:15 -0400)]
tile: default to tilegx_defconfig for ARCH=tile
There is no "ARCH=tile" (just like there is no "ARCH=x86") so we need
to pick a default configuration, either tilepro or tilegx, when users
specify ARCH=tile. We'll use tilegx, since that's our current chip.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 25 May 2012 16:32:09 +0000 (12:32 -0400)]
tile: fix bug where fls(0) was not returning 0
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Sat, 7 Apr 2012 19:58:24 +0000 (15:58 -0400)]
arch/tile: mark TILEGX as not EXPERIMENTAL
Also create a TILEPRO config setting to use for #ifdefs where it
is cleaner to do so, and make the 64BIT setting depend directly
on the setting of TILEGX.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Kautuk Consul [Sat, 31 Mar 2012 12:05:39 +0000 (08:05 -0400)]
tile/mm/fault.c: Port OOM changes to handle_page_fault
Commit
d065bd810b6deb67d4897a14bfe21f8eb526ba99
(mm: retry page fault when blocking on disk transfer) and
commit
37b23e0525d393d48a7d59f870b3bc061a30ccdb
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to tile.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
[cmetcalf@tilera.com: initialize "flags" after "write" updated.]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 30 Mar 2012 20:31:08 +0000 (16:31 -0400)]
arch/tile: add descriptive text if the kernel reports a bad trap
If the kernel unexpectedly takes a bad trap, it's convenient to
have it report the type of trap as part of the error. This gives
customers a bit more context before they call up customer support.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 30 Mar 2012 20:21:17 +0000 (16:21 -0400)]
arch/tile: allow querying cpu module information from the hypervisor
This just adds a few more attributes to the information Linux
can query from the hypervisor for the /sys/hypervisor/board/ directory,
providing part, serial#, revision#, and description for cpu modules
(as opposed to the board itself, or any mezzanine boards).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 30 Mar 2012 20:01:48 +0000 (16:01 -0400)]
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
The hardwall drain code was not properly implemented for tilegx,
just tilepro, so you couldn't reliably restart an application that
made use of the udn.
In addition, the code was only applicable to the udn (user dynamic
network). On tilegx there is a second user network that is available
(the "idn"), and there is support for having I/O shims deliver
user-level interrupts to applications ("ipi") which functions in a
very similar way to the inter-core permissions used for udn/idn.
So this change also generalizes the code from supporting just the udn
to supports udn/idn/ipi on tilegx.
By default we now use /dev/hardwall/{udn,idn,ipi} with separate
minor numbers for the three devices.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Sun, 1 Apr 2012 18:04:21 +0000 (14:04 -0400)]
arch/tile: support multiple huge page sizes dynamically
This change adds support for a new "super" bit in the PTE, using the new
arch_make_huge_pte() method. The Tilera hypervisor sees the bit set at a
given level of the page table and gangs together 4, 16, or 64 consecutive
pages from that level of the hierarchy to create a larger TLB entry.
One extra "super" page size can be specified at each of the three levels
of the page table hierarchy on tilegx, using the "hugepagesz" argument
on the boot command line. A new hypervisor API is added to allow Linux
to tell the hypervisor how many PTEs to gang together at each level of
the page table.
To allow pre-allocating huge pages larger than the buddy allocator can
handle, this change modifies the Tilera bootmem support to put all of
memory on tilegx platforms into bootmem.
As part of this change I eliminate the vestigial CONFIG_HIGHPTE support,
which never worked anyway, and eliminate the hv_page_size() API in favor
of the standard vma_kernel_pagesize() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Sun, 1 Apr 2012 18:01:34 +0000 (14:01 -0400)]
mm: add new arch_make_huge_pte() method for tile support
The tile support for multiple-size huge pages requires tagging
the hugetlb PTE with a "super" bit for PTEs that are multiples of
the basic size of a pagetable span. To set that bit properly
we need to tweak the PTe in make_huge_pte() based on the vma.
This change provides the API for a subsequent tile-specific
change to use.
Reviewed-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 19:48:23 +0000 (15:48 -0400)]
arch/tile: support kexec() for tilegx
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 19:25:59 +0000 (15:25 -0400)]
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
We already had a syscall that did some dcache flushing, but it was
not used in practice. Make it MIPS compatible instead so it can
do both the DCACHE and ICACHE actions. We have code that wants to
be able to use the ICACHE flush mode from userspace so this change
enables that.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 17:58:43 +0000 (13:58 -0400)]
arch/tile: Allow tilegx to build with either 16K or 64K page size
This change introduces new flags for the hv_install_context()
API that passes a page table pointer to the hypervisor. Clients
can explicitly request 4K, 16K, or 64K small pages when they
install a new context. In practice, the page size is fixed at
kernel compile time and the same size is always requested every
time a new page table is installed.
The <hv/hypervisor.h> header changes so that it provides more abstract
macros for managing "page" things like PFNs and page tables. For
example there is now a HV_DEFAULT_PAGE_SIZE_SMALL instead of the old
HV_PAGE_SIZE_SMALL. The various PFN routines have been eliminated and
only PA- or PTFN-based ones remain (since PTFNs are always expressed
in fixed 2KB "page" size). The page-table management macros are
renamed with a leading underscore and take page-size arguments with
the presumption that clients will use those macros in some single
place to provide the "real" macros they will use themselves.
I happened to notice the old hv_set_caching() API was totally broken
(it assumed 4KB pages) so I changed it so it would nominally work
correctly with other page sizes.
Tag modules with the page size so you can't load a module built with
a conflicting page size. (And add a test for SMP while we're at it.)
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 17:39:51 +0000 (13:39 -0400)]
arch/tile: optimize get_user/put_user and friends
Use direct load/store for the get_user/put_user.
Previously, we would call out to a helper routine that would do the
appropriate thing and then return, handling the possible exception
internally. Now we inline the load or store, along with a "we succeeded"
indication in a register; if the load or store faults, we write a
"we failed" indication into the same register and then return to the
following instruction. This is more efficient and gives us more compact
code, as well as being more in line with what other architectures do.
The special futex assembly source file for TILE-Gx also disappears in
this change; we just use the same inlining idiom there as well, putting
the appropriate atomic operations directly into futex_atomic_op_inuser()
(and thus into the FUTEX_WAIT function).
The underlying atomic copy_from_user, copy_to_user functions were
renamed using the (cryptic) x86 convention as copy_from_user_ll and
copy_to_user_ll.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 17:30:31 +0000 (13:30 -0400)]
arch/tile: support building big-endian kernel
The toolchain supports big-endian mode now, so add support for building
the kernel to run big-endian as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Wed, 28 Mar 2012 17:59:18 +0000 (13:59 -0400)]
arch/tile: allow building Linux with transparent huge pages enabled
The change adds some infrastructure for managing tile pmd's more generally,
using pte_pmd() and pmd_pte() methods to translate pmd values to and
from ptes, since on TILEPro a pmd is really just a nested structure
holding a pgd (aka pte). Several existing pmd methods are moved into
this framework, and a whole raft of additional pmd accessors are defined
that are used by the transparent hugepage framework.
The tile PTE now has a "client2" bit. The bit is used to indicate a
transparent huge page is in the process of being split into subpages.
This change also fixes a generic bug where the return value of the
generic pmdp_splitting_flush() was incorrect.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Tue, 27 Mar 2012 19:40:20 +0000 (15:40 -0400)]
arch/tile: use interrupt critical sections less
In general we want to avoid ever touching memory while within an
interrupt critical section, since the page fault path goes through
a different path from the hypervisor when in an interrupt critical
section, and we carefully decided with tilegx that we didn't need
to support this path in the kernel. (On tilepro we did implement
that path as part of supporting atomic instructions in software.)
In practice we always need to touch the kernel stack, since that's
where we store the interrupt state before releasing the critical
section, but this change cleans up a few things. The IRQ_ENABLE
macro is split up so that when we want to enable interrupts in a
deferred way (e.g. for cpu_idle or for interrupt return) we can
read the per-cpu enable mask before entering the critical section.
The cache-migration code is changed to use interrupt masking instead
of interrupt critical sections. And, the interrupt-entry code is
changed so that we defer loading "tp" from per-cpu data until after
we have released the interrupt critical section.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Linus Torvalds [Fri, 25 May 2012 16:37:26 +0000 (09:37 -0700)]
Merge tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf
Pull dma-buf updates from Sumit Semwal:
"Here's the first signed-tag pull request for dma-buf framework. It
includes the following key items:
- mmap support
- vmap support
- related documentation updates
These are needed by various drivers to allow mmap/vmap of dma-buf
shared buffers. Dave Airlie has some prime patches dependent on the
vmap pull as well."
* tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: add initial vmap documentation
dma-buf: minor documentation fixes.
dma-buf: add vmap interface
dma-buf: mmap support
Linus Torvalds [Fri, 25 May 2012 16:31:59 +0000 (09:31 -0700)]
Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine updates from Vinod Koul:
"Nothing exciting this time, odd fixes in a bunch of drivers"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_hdmac: take maxburst from slave configuration
dmaengine: at_hdmac: remove ATC_DEFAULT_CTRLA constant
dmaengine: at_hdmac: remove some at_dma_slave comments
dma: imx-sdma: make channel0 operations atomic
dmaengine: Fixup dmaengine_prep_slave_single() to be actually useful
dmaengine: Use dma_sg_len(sg) instead of sg->length
dmaengine: Use sg_dma_address instead of sg_phys
DMA: PL330: Remove duplicate header file inclusion
dma: imx-sdma: keep the callbacks invoked in the tasklet
dmaengine: dw_dma: add Device Tree probing capability
dmaengine: dw_dmac: Add clk_{un}prepare() support
dma/amba-pl08x: add support for the Nomadik variant
dma/amba-pl08x: check for terminal count status only
Linus Torvalds [Fri, 25 May 2012 16:18:59 +0000 (09:18 -0700)]
Merge branch 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
Linus Torvalds [Fri, 25 May 2012 15:45:25 +0000 (08:45 -0700)]
Merge tag 'sound-3.5' of git://git./linux/kernel/git/tiwai/sound
Pull sound update from Takashi Iwai:
"This is the second updates for 3.5-rc1. It's mainly for OMAP4 HDMI
updates and the device tree updates for OMAP, in addition to a couple
of PCM accuray improvement and Realtek ALC269VD codec support."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek - Add new codec support for ALC269VD
ALSA: core: group read of pointer, tstamp and jiffies
ASoC: OMAP: HDMI: Rename sound card source file
ASoC: OMAP: HDMI: Make sound card naming more generic
ASoC: OMAP: HDMI: Make build config options more generic
ASoC: OMAP: HDMI: Expand capabilities of the HDMI DAI
ASoC: OMAP: HDMI: Improve how the display state is verified
ASoC: OMAP: HDMI: Expand configuration of hw_params
ASoC: OMAP: HDMI: Use the DSS audio interface
ASoC: OMAP: HDMI: Create a structure for private data of the CPU DAI
ASoC: OMAP: HDMI: Change error values in HDMI CPU DAI
ASoC: OMAP: HDMI: Update the platform device names
ASoC: omap-abe-twl6040: Introduce driver data for runtime parameters
ASoC: omap-abe-twl6040: Move Digital Mic widget into dapm table
ASoC: omap-abe-twl6040: Keep only one snd_soc_dai_link structure
ASoC: omap-dmic: Add device tree bindings
ASoC: omap-mcpdm: Add device tree bindings
ASoC: omap-mcbsp: buffer size constraint only applies to playback stream
ASoC: omap-mcbsp: Use the common interrupt line if supported by the SoC
ASoC: omap-mcbsp: Remove unused FRAME dma_op_mode
...
Linus Torvalds [Fri, 25 May 2012 15:38:26 +0000 (08:38 -0700)]
Merge tag 'hda-switcheroo' of git://git./linux/kernel/git/tiwai/sound
Pull VGA-switcheroo audio client support for HD-audio from Takashi Iwai.
This depended on the recent drm pull.
* tag 'hda-switcheroo' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - unlock on error in azx_interrupt()
ALSA: hda - Support VGA-switcheroo
ALSA: hda - Export snd_hda_lock_devices()
ALSA: hda - Check the dead HDMI audio controller by vga-switcheroo
Linus Torvalds [Fri, 25 May 2012 15:30:35 +0000 (08:30 -0700)]
Merge tag 'cris-for-linus' of git://jni.nu/cris
Pull CRIS changes from Jesper Nilsson:
"No major changes here, but fixes some compile errors for CRIS, some
small style issues, some documentation and as a bonus nukes a couple
of obsolete rtc-files and related code."
* tag 'cris-for-linus' of git://jni.nu/cris:
cris: Remove old legacy "-traditional" flag from arch-v10/lib/Makefile
CRIS: Remove legacy RTC drivers
cris/mm/fault.c: Port OOM changes to do_page_fault
cris:fix the wrong function declear
CRIS: Add _sdata to vmlinux.lds.S
cris: posix_types.h, include asm-generic/posix_types.h
CRIS: Update documentation
cris/arch-v32: cryptocop: Use kzalloc
net:removed the unused variable
cris:removed the unused variable
CRISv32: Correct name of read_mostly section.
Linus Torvalds [Fri, 25 May 2012 15:23:32 +0000 (08:23 -0700)]
Merge tag 'mmc-merge-for-3.5-rc1' of git://git./linux/kernel/git/cjb/mmc
Pull MMC changes from Chris Ball
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused
corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
Fix up the usual trivial conflicts in feature-removal-schedule.txt
* tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (38 commits)
mmc: at91-mci: this driver is now deprecated
mmc: omap_hsmmc: pass IRQF_ONESHOT to request_threaded_irq
mmc: block: Allow disabling 512B sector size emulation
mmc: atmel-mci: add debug logs
mmc: atmel-mci: add support for version lower than v2xx
mmc: atmel-mci: change the state machine for compatibility with old IP
mmc: atmel-mci: the r/w proof capability lack was not well managed
mmc: dw_mmc: Fixed sdio interrupt mask bit setting bug
mmc: omap: convert to module_platform_driver
mmc: omap: make it behave well as a module
mmc: omap: convert to per instance workqueue
mmc: core: Remove dead code
mmc: card: Avoid null pointer dereference
mmc: core: Prevent eMMC VCC supply to be cut from late init
mmc: dw_mmc: make multiple instances of dw_mci_card_workqueue
mmc: queue: remove redundant memsets
mmc: queue: rename mmc_request function
mmc: core: skip card initialization if power class selection fails
mmc: core: fix the signaling 1.8V for HS200
mmc: core: fix the decision of HS200/DDR card-type
...
Jonas Bonn [Fri, 25 May 2012 06:24:49 +0000 (08:24 +0200)]
openrisc: use generic strncpy_from_user
As per commits
2922585b9329 ("lib: Sparc's strncpy_from_user is generic
enough, move under lib/") and
92ae03f2ef99 ("x86: merge 32/64-bit
versions of 'strncpy_from_user()' and speed it up"), and corresponding
discussion on linux-arch.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 25 May 2012 15:14:59 +0000 (08:14 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull ext2, ext3 and quota fixes from Jan Kara:
"Interesting bits are:
- removal of a special i_mutex locking subclass (I_MUTEX_QUOTA) since
quota code does not need i_mutex anymore in any unusual way.
- backport (from ext4) of a fix of a checkpointing bug (missing cache
flush) that could lead to fs corruption on power failure
The rest are just random small fixes & cleanups."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: trivial fix to comment for ext2_free_blocks
ext2: remove the redundant comment for ext2_export_ops
ext3: return 32/64-bit dir name hash according to usage type
quota: Get rid of nested I_MUTEX_QUOTA locking subclass
quota: Use precomputed value of sb_dqopt in dquot_quota_sync
ext2: Remove i_mutex use from ext2_quota_write()
reiserfs: Remove i_mutex use from reiserfs_quota_write()
ext4: Remove i_mutex use from ext4_quota_write()
ext3: Remove i_mutex use from ext3_quota_write()
quota: Fix double lock in add_dquot_ref() with CONFIG_QUOTA_DEBUG
jbd: Write journal superblock with WRITE_FUA after checkpointing
jbd: protect all log tail updates with j_checkpoint_mutex
jbd: Split updating of journal superblock and marking journal empty
ext2: do not register write_super within VFS
ext2: Remove s_dirt handling
ext2: write superblock only once on unmount
ext3: update documentation with barrier=1 default
ext3: remove max_debt in find_group_orlov()
jbd: Refine commit writeout logic
Stefan Hajnoczi [Wed, 28 Mar 2012 08:32:32 +0000 (09:32 +0100)]
doc: ext3: update documentation with barrier=1 default
Commit
00eacd6 ("ext3: make ext3 mount default to barrier=1") changed
the default barrier mount option for ext3. The documentation needs to
be updated, so this patch does that.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Marcos Paulo de Souza [Thu, 12 Apr 2012 03:14:34 +0000 (00:14 -0300)]
Documentation/initrd.txt: Change the location of util-linux
The address of util-linux seems deprecated. The new util-linux location is
in the kernel.org. So, change this for the correct address.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Michel Machado [Tue, 3 Apr 2012 02:10:53 +0000 (22:10 -0400)]
Documentation/SubmittingPatches: suggested the use of scripts/get_maintainer.pl
Had I found a reference to scripts/get_maintainer.pl when I first read
Documentation/SubmittingPatches, it would've saved me some time.
Signed-off-by: Michel Machado <michel@digirati.com.br>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sebastian Andrzej Siewior [Mon, 26 Mar 2012 19:28:33 +0000 (21:28 +0200)]
Documentation/kernel-parameters: remove autotest and mcatest
It has no more users, the last one is gone in "[PATCH] ia64: Kconfig
cleanup" aka ("
6fd79ab50b").
mcatest is gone in commit "[PATCH] ia64: SGI SN update"
("
c6bacd5010ec").
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Julia Lawall [Sat, 21 Apr 2012 18:23:48 +0000 (20:23 +0200)]
scripts/coccinelle: sizeof of pointer
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Julia Lawall [Sat, 21 Apr 2012 18:14:58 +0000 (20:14 +0200)]
scripts/coccinelle: address test is always true
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Dave Airlie [Tue, 22 May 2012 12:34:38 +0000 (13:34 +0100)]
dma-buf: add initial vmap documentation
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Sumit Semwal [Wed, 23 May 2012 09:57:40 +0000 (15:27 +0530)]
dma-buf: minor documentation fixes.
Some minor inline documentation fixes for gaps resulting from new patches.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Dave Airlie [Sun, 20 May 2012 07:03:56 +0000 (12:33 +0530)]
dma-buf: add vmap interface
The main requirement I have for this interface is for scanning out
using the USB gpu devices. Since these devices have to read the
framebuffer on updates and linearly compress it, using kmaps
is a major overhead for every update.
v2: fix warn issues pointed out by Sylwester Nawrocki.
v3: fix compile !CONFIG_DMA_SHARED_BUFFER and add _GPL for now
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Daniel Vetter [Tue, 24 Apr 2012 09:08:52 +0000 (14:38 +0530)]
dma-buf: mmap support
Compared to Rob Clark's RFC I've ditched the prepare/finish hooks
and corresponding ioctls on the dma_buf file. The major reason for
that is that many people seem to be under the impression that this is
also for synchronization with outstanding asynchronous processsing.
I'm pretty massively opposed to this because:
- It boils down reinventing a new rather general-purpose userspace
synchronization interface. If we look at things like futexes, this
is hard to get right.
- Furthermore a lot of kernel code has to interact with this
synchronization primitive. This smells a look like the dri1 hw_lock,
a horror show I prefer not to reinvent.
- Even more fun is that multiple different subsystems would interact
here, so we have plenty of opportunities to create funny deadlock
scenarios.
I think synchronization is a wholesale different problem from data
sharing and should be tackled as an orthogonal problem.
Now we could demand that prepare/finish may only ensure cache
coherency (as Rob intended), but that runs up into the next problem:
We not only need mmap support to facilitate sw-only processing nodes
in a pipeline (without jumping through hoops by importing the dma_buf
into some sw-access only importer), which allows for a nicer
ION->dma-buf upgrade path for existing Android userspace. We also need
mmap support for existing importing subsystems to support existing
userspace libraries. And a loot of these subsystems are expected to
export coherent userspace mappings.
So prepare/finish can only ever be optional and the exporter /needs/
to support coherent mappings. Given that mmap access is always
somewhat fallback-y in nature I've decided to drop this optimization,
instead of just making it optional. If we demonstrate a clear need for
this, supported by benchmark results, we can always add it in again
later as an optional extension.
Other differences compared to Rob's RFC is the above mentioned support
for mapping a dma-buf through facilities provided by the importer.
Which results in mmap support no longer being optional.
Note that this dma-buf mmap patch does _not_ support every possible
insanity an existing subsystem could pull of with mmap: Because it
does not allow to intercept pagefaults and shoot down ptes importing
subsystems can't add some magic of their own at these points (e.g. to
automatically synchronize with outstanding rendering or set up some
special resources). I've done a cursory read through a few mmap
implementions of various subsytems and I'm hopeful that we can avoid
this (and the complexity it'd bring with it).
Additonally I've extended the documentation a bit to explain the hows
and whys of this mmap extension.
In case we ever want to add support for explicitly cache maneged
userspace mmap with a prepare/finish ioctl pair, we could specify that
userspace needs to mmap a different part of the dma_buf, e.g. the
range starting at dma_buf->size up to dma_buf->size*2. This works
because the size of a dma_buf is invariant over it's lifetime. The
exporter would obviously need to fall back to coherent mappings for
both ranges if a legacy clients maps the coherent range and the
architecture cannot suppor conflicting caching policies. Also, this
would obviously be optional and userspace needs to be able to fall
back to coherent mappings.
v2:
- Spelling fixes from Rob Clark.
- Compile fix for !DMA_BUF from Rob Clark.
- Extend commit message to explain how explicitly cache managed mmap
support could be added later.
- Extend the documentation with implementations notes for exporters
that need to manually fake coherency.
v3:
- dma_buf pointer initialization goof-up noticed by Rebecca Schultz
Zavin.
Cc: Rob Clark <rob.clark@linaro.org>
Cc: Rebecca Schultz Zavin <rebecca@android.com>
Acked-by: Rob Clark <rob.clark@linaro.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Kailang Yang [Fri, 25 May 2012 06:08:38 +0000 (08:08 +0200)]
ALSA: hda/realtek - Add new codec support for ALC269VD
Also fix some settings applied only for ALC269VB.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Edgar E. Iglesias [Fri, 24 Feb 2012 04:52:25 +0000 (14:52 +1000)]
microblaze: Setup correct pointer to TLS area
Setup a pointer to the TLS area in copy_thread.
r10 is 6th argumetn which contains TLS area.
And r21 is the thread reg.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Holsgrove <david.holsgrove@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Edgar E. Iglesias [Fri, 24 Feb 2012 04:52:26 +0000 (14:52 +1000)]
microblaze: Add TLS support to sys_clone
Formerly unused Args 4/5 now load parent tid / child tid so the brid to
do_fork can pick up TLS from r10. Arg 3 still unused
There is also necessary to fix old glibc which do not setup r9/r10 (arg 4/5).
Simple clearing them is fine.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Holsgrove <david.holsgrove@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Michal Simek [Mon, 7 May 2012 12:21:02 +0000 (14:21 +0200)]
microblaze: ftrace: Pass the first calling instruction for dynamic ftrace
Selftest for dynamic ftrace requres to pass address of the first
calling instruction because hash function is calculated from it.
ftrace_update_ftrace_func setups pointer to function which is called
in _mcount function. trace_selftest is not aware about instruction
size (for microblaze 8 - imm and addik) and that's why we have
to pass in r5 address of imm not addik which is in r15.12
For more info look at ftrace_ops_list_func/ftrace.c.
Signed-off-by: Michal Simek <monstr@monstr.eu>
projects / firefly-linux-kernel-4.4.55.git / log