iw_cxgb3: Fix incorrectly returning error on success

commit 67f1aee6f45059fd6b0f5b0ecb2c97ad0451f6b3 upstream.

The cxgb3_*_send() functions return NET_XMIT_ values, which are
positive integers values. So don't treat positive return values
as an error.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[a pox on developers and maintainers who do not cc: stable for bug fixes like this - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: omap2-mcspi: Prevent duplicate gpio_request

commit 2f538c017e1a8620d19553931199c6d6a6d31bb2 upstream.

Occasionally the setup function will be called multiple times. Only request
the gpio the first time otherwise -EBUSY will occur on subsequent calls to
setup.

Reported-by: Joseph Bell <joe@iachieved.it>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE

commit 7a64cd887fdb97f074c3fda03bee0bfb9faceac3 upstream.

There's one point was missed in the patch commit da49889deb34 ("staging:
binder: Support concurrent 32 bit and 64 bit processes."). When configure
BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of
void * is 64bit on 64bit system. Correct it here.

Signed-off-by: Lisa Du <cldu@marvell.com>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Fixes: da49889deb34 ("staging: binder: Support concurrent 32 bit and 64 bit processes.")
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: option: add "4G LTE usb-modem U901"

commit d061c1caa31d4d9792cfe48a2c6b309a0e01ef46 upstream.

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: option: add support for SIM7100E

commit 3158a8d416f4e1b79dcc867d67cb50013140772c upstream.

$ lsusb:
Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option

$ usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  2
P:  Vendor=1e0e ProdID=9001 Rev= 2.32
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

The last interface (6) is used for Android Composite ADB interface.

Serial port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
4: audio

Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cp210x: add IDs for GE B650V3 and B850V3 boards

commit 6627ae19385283b89356a199d7f03c75ba35fb29 upstream.

Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.

Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: Fix assignment of EP transfer resources

commit c450960187f45d4260db87c7dd4fc0bceb5565d8 upstream.

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda6187181 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: ems_usb: Fix possible tx overflow

commit 90cfde46586d2286488d8ed636929e936c0c9ab2 upstream.

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.

Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm thin: fix race condition when destroying thin pool workqueue

commit 18d03e8c25f173f4107a40d0b8c24defb6ed69f3 upstream.

When a thin pool is being destroyed delayed work items are
cancelled using cancel_delayed_work(), which doesn't guarantee that on
return the delayed item isn't running.  This can cause the work item to
requeue itself on an already destroyed workqueue.  Fix this by using
cancel_delayed_work_sync() which guarantees that on return the work item
is not running anymore.

Fixes: 905e51b39a555 ("dm thin: commit outstanding data every second")
Fixes: 85ad643b7e7e5 ("dm thin: add timeout to stop out-of-data-space mode holding IO forever")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: Change refill_dirty() to always scan entire disk if necessary

commit 627ccd20b4ad3ba836472468208e2ac4dfadbf03 upstream.

Previously, it would only scan the entire disk if it was starting from
the very start of the disk - i.e. if the previous scan got to the end.

This was broken by refill_full_stripes(), which updates last_scanned so
that refill_dirty was never triggering the searched_from_start path.

But if we change refill_dirty() to always scan the entire disk if
necessary, regardless of what last_scanned was, the code gets cleaner
and we fix that bug too.

Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: prevent crash on changing writeback_running

commit 8d16ce540c94c9d366eb36fc91b7154d92d6397b upstream.

Added a safeguard in the shutdown case. At least while not being
attached it is also possible to trigger a kernel bug by writing into
writeback_running. This change  adds the same check before trying to
wake up the thread for that case.

Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: allows use of register in udev to avoid "device_busy" error.

commit d7076f21629f8f329bca4a44dc408d94670f49e2 upstream.

Allows to use register, not register_quiet in udev to avoid "device_busy" error.
The initial patch proposed at https://lkml.org/lkml/2013/8/26/549 by Gabriel de Perthuis
<g2p.code@gmail.com> does not unlock the mutex and hangs the kernel.

See http://thread.gmane.org/gmane.linux.kernel.bcache.devel/2594 for the discussion.

Cc: Denis Bychkov <manover@gmail.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: unregister reboot notifier if bcache fails to unregister device

commit 2ecf0cdb2b437402110ab57546e02abfa68a716b upstream.

In bcache_init() function it forgot to unregister reboot notifier if
bcache fails to unregister a block device.  This commit fixes this.

Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: fix a leak in bch_cached_dev_run()

commit 4d4d8573a8451acc9f01cbea24b7e55f04a252fe upstream.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: clear BCACHE_DEV_UNLINK_DONE flag when attaching a backing device

commit fecaee6f20ee122ad75402c53d8278f9bb142ddc upstream.

This bug can be reproduced by the following script:

  #!/bin/bash

  bcache_sysfs="/sys/fs/bcache"

  function clear_cache()
  {
   if [ ! -e $bcache_sysfs ]; then
   echo "no bcache sysfs"
   exit
   fi

   cset_uuid=$(ls -l $bcache_sysfs|head -n 2|tail -n 1|awk '{print $9}')
   sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/detach"
   sleep 5
   sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/attach"
  }

  for ((i=0;i<10;i++)); do
   clear_cache
  done

The warning messages look like below:
[  275.948611] ------------[ cut here ]------------
[  275.963840] WARNING: at fs/sysfs/dir.c:512 sysfs_add_one+0xb8/0xd0() (Tainted: P        W
---------------   )
[  275.979253] Hardware name: Tecal RH2285
[  275.994106] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:09.0/0000:08:00.0/host4/target4:2:1/4:2:1:0/block/sdb/sdb1/bcache/cache'
[  276.024105] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler
bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas
pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan]
[  276.072643] Pid: 2765, comm: sh Tainted: P        W  ---------------    2.6.32 #1
[  276.089315] Call Trace:
[  276.105801]  [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0
[  276.122650]  [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50
[  276.139361]  [<ffffffff81205c08>] ? sysfs_add_one+0xb8/0xd0
[  276.156012]  [<ffffffff8120609b>] ? sysfs_do_create_link+0x12b/0x170
[  276.172682]  [<ffffffff81206113>] ? sysfs_create_link+0x13/0x20
[  276.189282]  [<ffffffffa03bda21>] ? bcache_device_link+0xc1/0x110 [bcache]
[  276.205993]  [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache]
[  276.222794]  [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache]
[  276.239680]  [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110
[  276.256594]  [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170
[  276.273364]  [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0
[  276.290133]  [<ffffffff811890b1>] ? sys_write+0x51/0x90
[  276.306368]  [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b
[  276.322301] ---[ end trace 9f5d4fcdd0c3edfb ]---
[  276.338241] ------------[ cut here ]------------
[  276.354109] WARNING: at /home/wenqing.lz/bcache/bcache/super.c:720
bcache_device_link+0xdf/0x110 [bcache]() (Tainted: P        W  ---------------   )
[  276.386017] Hardware name: Tecal RH2285
[  276.401430] Couldn't create device <-> cache set symlinks
[  276.401759] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler
bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas
pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan]
[  276.465477] Pid: 2765, comm: sh Tainted: P        W  ---------------    2.6.32 #1
[  276.482169] Call Trace:
[  276.498610]  [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0
[  276.515405]  [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50
[  276.532059]  [<ffffffffa03bda3f>] ? bcache_device_link+0xdf/0x110 [bcache]
[  276.548808]  [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache]
[  276.565569]  [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache]
[  276.582418]  [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110
[  276.599341]  [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170
[  276.616142]  [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0
[  276.632607]  [<ffffffff811890b1>] ? sys_write+0x51/0x90
[  276.648671]  [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b
[  276.664756] ---[ end trace 9f5d4fcdd0c3edfc ]---

We forget to clear BCACHE_DEV_UNLINK_DONE flag in bcache_device_attach()
function when we attach a backing device first time.  After detaching this
backing device, this flag will be true and sysfs_remove_link() isn't called in
bcache_device_unlink().  Then when we attach this backing device again,
sysfs_create_link() will return EEXIST error in bcache_device_link().

So the fix is trival and we clear this flag in bcache_device_link().

Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: Add a cond_resched() call to gc

commit c5f1e5adf956e3ba82d204c7c141a75da9fa449a upstream.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: fix a livelock when we cause a huge number of cache misses

commit 2ef9ccbfcb90cf84bdba320a571b18b05c41101b upstream.

Subject : [PATCH v2] bcache: fix a livelock in btree lock
Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM)

This commit tries to fix a livelock in bcache.  This livelock might
happen when we causes a huge number of cache misses simultaneously.

When we get a cache miss, bcache will execute the following path.

->cached_dev_make_request()
  ->cached_dev_read()
    ->cached_lookup()
      ->bch->btree_map_keys()
        ->btree_root()  <------------------------
          ->bch_btree_map_keys_recurse()        |
            ->cache_lookup_fn()                 |
              ->cached_dev_cache_miss()         |
                ->bch_btree_insert_check_key() -|
                  [If btree->seq is not equal to seq + 1, we should return
                   EINTR and traverse btree again.]

In bch_btree_insert_check_key() function we first need to check upgrade
flag (op->lock == -1), and when this flag is true we need to release
read btree->lock and try to take write btree->lock.  During taking and
releasing this write lock, btree->seq will be monotone increased in
order to prevent other threads modify this in cache miss (see btree.h:74).
But if there are some cache misses caused by some requested, we could
meet a livelock because btree->seq is always changed by others.  Thus no
one can make progress.

This commit will try to take write btree->lock if it encounters a race
when we traverse btree.  Although it sacrifice the scalability but we
can ensure that only one can modify the btree.

Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Joshua Schmid <jschmid@suse.com>
Cc: Zhu Yanhai <zhu.yanhai@gmail.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/ucs2_string: Correct ucs2 -> utf8 conversion

commit a68075908a37850918ad96b056acc9ac4ce1bd90 upstream.

The comparisons should be >= since 0x800 and 0x80 require an additional bit
to store.

For the 3 byte case, the existing shift would drop off 2 more bits than
intended.

For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in
byte 2.

Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@coreos.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Add pstore variables to the deletion whitelist

commit e246eb568bc4cbbdd8a30a3c11151ff9b7ca7312 upstream.

Laszlo explains why this is a good idea,

 'This is because the pstore filesystem can be backed by UEFI variables,
  and (for example) a crash might dump the last kilobytes of the dmesg
  into a number of pstore entries, each entry backed by a separate UEFI
  variable in the above GUID namespace, and with a variable name
  according to the above pattern.

  Please see "drivers/firmware/efi/efi-pstore.c".

  While this patch series will not prevent the user from deleting those
  UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
  entry will continue to delete the backing UEFI variable), I think it
  would be nice to preserve the possibility for the sysadmin to delete
  Linux-created UEFI variables that carry portions of the crash log,
  *without* having to mount the pstore filesystem.'

There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.

Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.

Reported-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Tested-by: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Make efivarfs entries immutable by default

commit ed8b0de5a33d2a2557dce7f9429dca8cb5bc5879 upstream.

"rm -rf" is bricking some peoples' laptops because of variables being
used to store non-reinitializable firmware driver data that's required
to POST the hardware.

These are 100% bugs, and they need to be fixed, but in the mean time it
shouldn't be easy to *accidentally* brick machines.

We have to have delete working, and picking which variables do and don't
work for deletion is quite intractable, so instead make everything
immutable by default (except for a whitelist), and make tools that
aren't quite so broad-spectrum unset the immutable flag.

Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Make our variable validation list include the guid

commit 8282f5d9c17fe15a9e658c06e3f343efae1a2a2f upstream.

All the variables in this list so far are defined to be in the global
namespace in the UEFI spec, so this just further ensures we're
validating the variables we think we are.

Including the guid for entries will become more important in future
patches when we decide whether or not to allow deletion of variables
based on presence in this list.

Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Do variable name validation tests in utf8

commit 3dcb1f55dfc7631695e69df4a0d589ce5274bd07 upstream.

Actually translate from ucs2 to utf8 before doing the test, and then
test against our other utf8 data, instead of fudging it.

Signed-off-by: Peter Jones <pjones@redhat.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version

commit e0d64e6a880e64545ad7d55786aa84ab76bac475 upstream.

Translate EFI's UCS-2 variable names to UTF-8 instead of just assuming
all variable names fit in ASCII.

Signed-off-by: Peter Jones <pjones@redhat.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/ucs2_string: Add ucs2 -> utf8 helper functions

commit 73500267c930baadadb0d02284909731baf151f7 upstream.

This adds ucs2_utf8size(), which tells us how big our ucs2 string is in
bytes, and ucs2_as_utf8, which translates from ucs2 to utf8..

Signed-off-by: Peter Jones <pjones@redhat.com>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8457/1: psci-smp is built only for SMP

commit be95485a0b8288a93402705730d3ea32f9f812b9 upstream.

The PSCI SMP implementation is built only when both CONFIG_SMP and
CONFIG_ARM_PSCI are set, so a configuration that has the latter
but not the former can get a link error when it tries to call
psci_smp_available().

arch/arm/mach-tegra/built-in.o: In function `tegra114_cpuidle_init':
cpuidle-tegra114.c:(.init.text+0x52a): undefined reference to `psci_smp_available'

This corrects the #ifdef in the psci.h header file to match the
Makefile conditional we have for building that function.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/gma500: Use correct unref in the gem bo create function

commit d3e376f52d095103ca51dbda4d6ff8aaf488f98f upstream.

This is called without dev->struct_mutex held, we need to use the
_unlocked variant.

Never caught in the wild since you'd need an evil userspace which
races a gem_close ioctl call with the in-progress open.

Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-17-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_memremap: Fix error value when memremap failed

commit 93f834df9c2d4e362dfdc4b05daa0a4e18814836 upstream.

devm_memremap() returns an ERR_PTR() value in case of error.
However, it returns NULL when memremap() failed.  This causes
the caller, such as the pmem driver, to proceed and oops later.

Change devm_memremap() to return ERR_PTR(-ENXIO) when memremap()
failed.

Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: fix guest fprs memory leak

commit 9c7ebb613bffea2feef4ec562ba1dbcaa810942b upstream.

fprs is never freed, therefore resulting in a memory leak if
kvm_vcpu_init() fails or the vcpu is destroyed.

Fixes: 9977e886cbbc ("s390/kernel: lazy restore fpu registers")
Reported-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: errata: Add -mpc-relative-literal-loads to build flags

commit 67dfa1751ce71e629aad7c438e1678ad41054677 upstream.

GCC6 (and Linaro's 2015.12 snapshot of GCC5) has a new default that uses
adrp/ldr or adrp/add to address literal pools. When CONFIG_ARM64_ERRATUM_843419
is enabled, modules built with this toolchain fail to load:

  module libahci: unsupported RELA relocation: 275

This patch fixes the problem by passing '-mpc-relative-literal-loads'
to the compiler.

Cc: stable@vger.kernel.org
Fixes: df057cc7b4fa ("arm64: errata: add module build workaround for erratum #843419")
BugLink: http://bugs.launchpad.net/bugs/1533009
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Christophe Lyon <christophe.lyon@linaro.org>
Signed-off-by: Dann Frazier <dann.frazier@canonical.com>
[will: backport to 4.4-stable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: debug-ll: fix BCM63xx entry for multiplatform

commit 6c54809977de3c9e2ef9e9934a2c6625f7e161e7 upstream.

During my randconfig build testing, I found that a kernel with
DEBUG_AT91_UART and ARCH_BCM_63XX fails to build:

arch/arm/include/debug/at91.S:18:0: error: "CONFIG_DEBUG_UART_VIRT" redefined [-Werror]

It turns out that the DEBUG_UART_BCM63XX option is enabled whenever
the ARCH_BCM_63XX is, and that breaks multiplatform kernels because
we then end up using the UART address from BCM63XX rather than the
one we actually configured (if any).

This changes the BCM63XX options to only have one Kconfig option,
and only enable that if the user explicitly turns it on.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b51312bebfa4 ("ARM: BCM63XX: add low-level UART debug support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix bh->b_state corruption

commit ed8ad83808f009ade97ebbf6519bc3a97fefbc0c upstream.

ext4 can update bh->b_state non-atomically in _ext4_get_block() and
ext4_da_get_block_prep(). Usually this is fine since bh is just a
temporary storage for mapping information on stack but in some cases it
can be fully living bh attached to a page. In such case non-atomic
update of bh->b_state can race with an atomic update which then gets
lost. Usually when we are mapping bh and thus updating bh->b_state
non-atomically, nobody else touches the bh and so things work out fine
but there is one case to especially worry about: ext4_finish_bio() uses
BH_Uptodate_Lock on the first bh in the page to synchronize handling of
PageWriteback state. So when blocksize < pagesize, we can be atomically
modifying bh->b_state of a buffer that actually isn't under IO and thus
can race e.g. with delalloc trying to map that buffer. The result is
that we can mistakenly set / clear BH_Uptodate_Lock bit resulting in the
corruption of PageWriteback state or missed unlock of BH_Uptodate_Lock.

Fix the problem by always updating bh->b_state bits atomically.

Reported-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
[NB: Backported to 4.4.2]
Acked-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: Fix port hash table size computation

[ Upstream commit d9749fb5942f51555dc9ce1ac0dbb1806960a975 ]

Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires.  The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table).  Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).

To fix this, we change the logic slightly.  We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support.  Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made.  Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.

I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Dmitry Vyukov <dvyukov@google.com>
CC: Vladislav Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

unix_diag: fix incorrect sign extension in unix_lookup_by_ino

[ Upstream commit b5f0549231ffb025337be5a625b0ff9f52b016f0 ]

The value passed by unix_diag_get_exact to unix_lookup_by_ino has type
__u32, but unix_lookup_by_ino's argument ino has type int, which is not
a problem yet.
However, when ino is compared with sock_i_ino return value of type
unsigned long, ino is sign extended to signed long, and this results
to incorrect comparison on 64-bit architectures for inode numbers
greater than INT_MAX.

This bug was found by strace test suite.

Fixes: 5d3cae8bc39d ("unix_diag: Dumping exact socket core")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: unlock in error path

[ Upstream commit b53ce3e7d407aa4196877a48b8601181162ab158 ]

tipc_bcast_unlock need to be unlocked in error path.

Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtnl: RTM_GETNETCONF: fix wrong return value

[ Upstream commit a97eb33ff225f34a8124774b3373fd244f0e83ce ]

An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.

Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IFF_NO_QUEUE: Fix for drivers not calling ether_setup()

[ Upstream commit a813104d923339144078939175faf4e66aca19b4 ]

My implementation around IFF_NO_QUEUE driver flag assumed that leaving
tx_queue_len untouched (specifically: not setting it to zero) by drivers
would make it possible to assign a regular qdisc to them without having
to worry about setting tx_queue_len to a useful value. This was only
partially true: I overlooked that some drivers don't call ether_setup()
and therefore not initialize tx_queue_len to the default value of 1000.
Consequently, removing the workarounds in place for that case in qdisc
implementations which cared about it (namely, pfifo, bfifo, gred, htb,
plug and sfb) leads to problems with these specific interface types and
qdiscs.

Luckily, there's already a sanitization point for drivers setting
tx_queue_len to zero, which can be reused to assign the fallback value
most qdisc implementations used, which is 1.

Fixes: 348e3435cbefa ("net: sched: drop all special handling of tx_queue_len == 0")
Tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp/dccp: fix another race at listener dismantle

[ Upstream commit 7716682cc58e305e22207d5bb315f26af6b1e243 ]

Ilya reported following lockdep splat:

kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory
ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0:  (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1:  (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2:  (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3:  (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0

To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.

We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.

Reported-by: Ilya Dryomov <idryomov@gmail.com>
Fixes: ebb516af60e1 ("tcp/dccp: fix race at listener dismantle phase")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

route: check and remove route cache when we get route

[ Upstream commit deed49df7390d5239024199e249190328f1651e7 ]

Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.

Fix this issue by checking  and removing route cache when we get route.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net_sched fix: reclassification needs to consider ether protocol changes

[ Upstream commit 619fe32640b4b01f370574d50344ae0f62689816 ]

actions could change the etherproto in particular with ethernet
tunnelled data. Typically such actions, after peeling the outer header,
will ask for the packet to be  reclassified. We then need to restart
the classification with the new proto header.

Example setup used to catch this:
sudo tc qdisc add dev $ETH ingress
sudo $TC filter add dev $ETH parent ffff: pref 1 protocol 802.1Q \
u32 match u32 0 0 flowid 1:1 \
action  vlan pop reclassify

Fixes: 3b3ae880266d ("net: sched: consolidate tc_classify{,_compat}")
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pppoe: fix reference counting in PPPoE proxy

[ Upstream commit 29e73269aa4d36f92b35610c25f8b01c789b0dc8 ]

Drop reference on the relay_po socket when __pppoe_xmit() succeeds.
This is already handled correctly in the error path.

Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: Fix error creating L2TP tunnels

[ Upstream commit 853effc55b0f975abd6d318cca486a9c1b67e10f ]

A previous commit (33f72e6) added notification via netlink for tunnels
when created/modified/deleted. If the notification returned an error,
this error was returned from the tunnel function. If there were no
listeners, the error code ESRCH was returned, even though having no
listeners is not an error. Other calls to this and other similar
notification functions either ignore the error code, or filter ESRCH.
This patch checks for ESRCH and does not flag this as an error.

Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: Avoid changing dev->features directly in run-time

[ Upstream commit 925ab1aa9394bbaeac47ee5b65d3fdf0fb8135cf ]

It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.

Fixes: f4a1edd56120 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: Choose time-stamping shift value according to HW frequency

[ Upstream commit 31c128b66e5b28f468076e4f3ca3025c35342041 ]

Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.

Algorithm for shift value calculation:
 * Round up the maximal value in cycles to nearest power of two

 * Calculate maximal multiplier by division of all 64 bits set
   to above result

 * Then, invert the function clocksource_khz2mult() to get the shift from
   maximal mult value

Fixes: ec693d47010e ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: Count HW buffer overrun only once

[ Upstream commit 281e8b2fdf8e4ef366b899453cae50e09b577ada ]

RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.

Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.

Fix that. Use it for rx_fifo_errors only.

Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qmi_wwan: add "4G LTE usb-modem U901"

[ Upstream commit aac8d3c282e024c344c5b86dc1eab7af88bb9716 ]

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: md5: release request socket instead of listener

[ Upstream commit 729235554d805c63e5e274fcc6a98e71015dd847 ]

If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.

The bug was added for IPv4 only.

Fixes: 079096f103fac ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: fix premature addition of node to lookup table

[ Upstream commit d5c91fb72f1652ea3026925240a0998a42ddb16b ]

In commit 5266698661401a ("tipc: let broadcast packet reception
use new link receive function") we introduced a new per-node
broadcast reception link instance. This link is created at the
moment the node itself is created. Unfortunately, the allocation
is done after the node instance has already been added to the node
lookup hash table. This creates a potential race condition, where
arriving broadcast packets are able to find and access the node
before it has been fully initialized, and before the above mentioned
link has been created. The result is occasional crashes in the function
tipc_bcast_rcv(), which is trying to access the not-yet existing link.

We fix this by deferring the addition of the node instance until after
it has been fully initialized in the function tipc_node_create().

Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_unix: Guard against other == sk in unix_dgram_sendmsg

[ Upstream commit a5527dda344fff0514b7989ef7a755729769daa1 ]

The unix_dgram_sendmsg routine use the following test

if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {

to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.

Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue")
Reported-By: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Tested-by: Philipp Hahn <pmhahn@pmhahn.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_unix: Don't set err in unix_stream_read_generic unless there was an error

[ Upstream commit 1b92ee3d03af6643df395300ba7748f19ecdb0c5 ]

The present unix_stream_read_generic contains various code sequences of
the form

err = -EDISASTER;
if (<test>)
goto out;

This has the unfortunate side effect of possibly causing the error code
to bleed through to the final

out:
return copied ? : err;

and then to be wrongly returned if no data was copied because the caller
didn't supply a data buffer, as demonstrated by the program available at

http://pad.lv/1540731

Change it such that err is only set if an error condition was detected.

Fixes: 3822b5c2fc62 ("af_unix: Revert 'lock_interruptible' in stream receive code")
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: fix memory leaks in ip_cmsg_send() callers

[ Upstream commit 919483096bfe75dda338e98d56da91a263746a0a ]

Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.

Callers are responsible for the freeing.

Many thanks to Dmitry for the report and diagnostic.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: Fix ARP monitor validation

[ Upstream commit 21a75f0915dde8674708b39abfcda113911c49b1 ]

The current logic in bond_arp_rcv will accept an incoming ARP for
validation if (a) the receiving slave is either "active" (which includes
the currently active slave, or the current ARP slave) or, (b) there is a
currently active slave, and it has received an ARP since it became active.
For case (b), the receiving slave isn't the currently active slave, and is
receiving the original broadcast ARP request, not an ARP reply from the
target.

This logic can fail if there is no currently active slave.  In
this situation, the ARP probe logic cycles through all slaves, assigning
each in turn as the "current_arp_slave" for one arp_interval, then setting
that one as "active," and sending an ARP probe from that slave.  The
current logic expects the ARP reply to arrive on the sending
current_arp_slave, however, due to switch FDB updating delays, the reply
may be directed to another slave.

This can arise if the bonding slaves and switch are working, but
the ARP target is not responding.  When the ARP target recovers, a
condition may result wherein the ARP target host replies faster than the
switch can update its forwarding table, causing each ARP reply to be sent
to the previous current_arp_slave.  This will never pass the logic in
bond_arp_rcv, as neither of the above conditions (a) or (b) are met.

Some experimentation on a LAN shows ARP reply round trips in the
200 usec range, but my available switches never update their FDB in less
than 4000 usec.

This patch changes the logic in bond_arp_rcv to additionally
accept an ARP reply for validation on any slave if there is a current ARP
slave and it sent an ARP probe during the previous arp_interval.

Fixes: aeea64ac717a ("bonding: don't trust arp requests unless active slave really works")
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: fix branch offset adjustment on backjumps after patching ctx expansion

[ Upstream commit a1b14d27ed0965838350f1377ff97c93ee383492 ]

When ctx access is used, the kernel often needs to expand/rewrite
instructions, so after that patching, branch offsets have to be
adjusted for both forward and backward jumps in the new eBPF program,
but for backward jumps it fails to account the delta. Meaning, for
example, if the expansion happens exactly on the insn that sits at
the jump target, it doesn't fix up the back jump offset.

Analysis on what the check in adjust_branches() is currently doing:

  /* adjust offset of jmps if necessary */
  if (i < pos && i + insn->off + 1 > pos)
    insn->off += delta;
  else if (i > pos && i + insn->off + 1 < pos)
    insn->off -= delta;

First condition (forward jumps):

  Before:                         After:

  insns[0]                        insns[0]
  insns[1] <--- i/insn            insns[1] <--- i/insn
  insns[2] <--- pos               insns[P] <--- pos
  insns[3]                        insns[P]  `------| delta
  insns[4] <--- target_X          insns[P]   `-----|
  insns[5]                        insns[3]
                                  insns[4] <--- target_X
                                  insns[5]

First case is if we cross pos-boundary and the jump instruction was
before pos. This is handeled correctly. I.e. if i == pos, then this
would mean our jump that we currently check was the patchlet itself
that we just injected. Since such patchlets are self-contained and
have no awareness of any insns before or after the patched one, the
delta is correctly not adjusted. Also, for the second condition in
case of i + insn->off + 1 == pos, means we jump to that newly patched
instruction, so no offset adjustment are needed. That part is correct.

Second condition (backward jumps):

  Before:                         After:

  insns[0]                        insns[0]
  insns[1] <--- target_X          insns[1] <--- target_X
  insns[2] <--- pos <-- target_Y  insns[P] <--- pos <-- target_Y
  insns[3]                        insns[P]  `------| delta
  insns[4] <--- i/insn            insns[P]   `-----|
  insns[5]                        insns[3]
                                  insns[4] <--- i/insn
                                  insns[5]

Second interesting case is where we cross pos-boundary and the jump
instruction was after pos. Backward jump with i == pos would be
impossible and pose a bug somewhere in the patchlet, so the first
condition checking i > pos is okay only by itself. However, i +
insn->off + 1 < pos does not always work as intended to trigger the
adjustment. It works when jump targets would be far off where the
delta wouldn't matter. But, for example, where the fixed insn->off
before pointed to pos (target_Y), it now points to pos + delta, so
that additional room needs to be taken into account for the check.
This means that i) both tests here need to be adjusted into pos + delta,
and ii) for the second condition, the test needs to be <= as pos
itself can be a target in the backjump, too.

Fixes: 9bac3d6d548e ("bpf: allow extended BPF programs access skb fields")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen

[ Upstream commit 461547f3158978c180d74484d58e82be9b8e7357 ]

This patch fixes an issue with unaligned accesses when using
eth_get_headlen on a page that was DMA aligned instead of being IP aligned.
The fact is when trying to check the length we don't need to be looking at
the flow label so we can reorder the checks to first check if we are
supposed to gather the flow label and then make the call to actually get
it.

v2:  Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can
     cause us to check for the flow label.

Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Copy inner L3 and L4 headers as unaligned on GRE TEB

[ Upstream commit 78565208d73ca9b654fb9a6b142214d52eeedfd1 ]

This patch corrects the unaligned accesses seen on GRE TEB tunnels when
generating hash keys.  Specifically what this patch does is make it so that
we force the use of skb_copy_bits when the GRE inner headers will be
unaligned due to NET_IP_ALIGNED being a non-zero value.

Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: translate network order to host order when users get a hmacid

[ Upstream commit 7a84bd46647ff181eb2659fdc99590e6f16e501d ]

Commit ed5a377d87dc ("sctp: translate host order to network order when
setting a hmacid") corrected the hmacid byte-order when setting a hmacid.
but the same issue also exists on getting a hmacid.

We fix it by changing hmacids to host order when users get them with
getsockopt.

Fixes: Commit ed5a377d87dc ("sctp: translate host order to network order when setting a hmacid")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

enic: increment devcmd2 result ring in case of timeout

[ Upstream commit ca7f41a4957b872577807169bd7464b36aae9b9c ]

Firmware posts the devcmd result in result ring. In case of timeout, driver
does not increment the current result pointer and firmware could post the
result after timeout has occurred. During next devcmd, driver would be
reading the result of previous devcmd.

Fix this by incrementing result even in case of timeout.

Fixes: 373fb0873d43 ("enic: add devcmd2")
Signed-off-by: Sandeep Pillai <sanpilla@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs

[ Upstream commit b7d987295c74500b733a0ba07f9a9bcc4074fa83 ]

tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.

tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.

This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.

v2: Corrected patch description to avoid confusion.

Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net:Add sysctl_max_skb_frags

[ Upstream commit 5f74f82ea34c0da80ea0b49192bb5ea06e063593 ]

Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.

Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: do not drop syn_recv on all icmp reports

[ Upstream commit 9cf7490360bf2c46a16b7525f899e4970c5fc144 ]

Petr Novopashenniy reported that ICMP redirects on SYN_RECV sockets
were leading to RST.

This is of course incorrect.

A specific list of ICMP messages should be able to drop a SYN_RECV.

For instance, a REDIRECT on SYN_RECV shall be ignored, as we do
not hold a dst per SYN_RECV pseudo request.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111751
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

unix: correctly track in-flight fds in sending process user_struct

[ Upstream commit 415e3d3e90ce9e18727e8843ae343eda5a58fad6 ]

The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.

To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.

Fixes: 712f4aad406bb1 ("unix: properly account for FDs passed over unix sockets")
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: fix a lockdep splat

[ Upstream commit 44c3d0c1c0a880354e9de5d94175742e2c7c9683 ]

Silence lockdep false positive about rcu_dereference() being
used in the wrong context.

First one should use rcu_dereference_protected() as we own the spinlock.

Second one should be a normal assignation, as no barrier is needed.

Fixes: 18367681a10bd ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: addrconf: Fix recursive spin lock call

[ Upstream commit 16186a82de1fdd868255448274e64ae2616e2640 ]

A rcu stall with the following backtrace was seen on a system with
forwarding, optimistic_dad and use_optimistic set. To reproduce,
set these flags and allow ipv6 autoconf.

This occurs because the device write_lock is acquired while already
holding the read_lock. Back trace below -

INFO: rcu_preempt self-detected stall on CPU { 1}  (t=2100 jiffies
 g=3992 c=3991 q=4471)
<6> Task dump for CPU 1:
<2> kworker/1:0     R  running task    12168    15   2 0x00000002
<2> Workqueue: ipv6_addrconf addrconf_dad_work
<6> Call trace:
<2> [<ffffffc000084da8>] el1_irq+0x68/0xdc
<2> [<ffffffc000cc4e0c>] _raw_write_lock_bh+0x20/0x30
<2> [<ffffffc000bc5dd8>] __ipv6_dev_ac_inc+0x64/0x1b4
<2> [<ffffffc000bcbd2c>] addrconf_join_anycast+0x9c/0xc4
<2> [<ffffffc000bcf9f0>] __ipv6_ifa_notify+0x160/0x29c
<2> [<ffffffc000bcfb7c>] ipv6_ifa_notify+0x50/0x70
<2> [<ffffffc000bd035c>] addrconf_dad_work+0x314/0x334
<2> [<ffffffc0000b64c8>] process_one_work+0x244/0x3fc
<2> [<ffffffc0000b7324>] worker_thread+0x2f8/0x418
<2> [<ffffffc0000bb40c>] kthread+0xe0/0xec

v2: do addrconf_dad_kick inside read lock and then acquire write
lock for ipv6_ifa_notify as suggested by Eric

Fixes: 7fd2561e4ebdd ("net: ipv6: Add a sysctl to make optimistic
addresses useful candidates")

Cc: Eric Dumazet <edumazet@google.com>
Cc: Erik Kline <ek@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6/udp: use sticky pktinfo egress ifindex on connect()

[ Upstream commit 1cdda91871470f15e79375991bd2eddc6e86ddb1 ]

Currently, the egress interface index specified via IPV6_PKTINFO
is ignored by __ip6_datagram_connect(), so that RFC 3542 section 6.7
can be subverted when the user space application calls connect()
before sendmsg().
Fix it by initializing properly flowi6_oif in connect() before
performing the route lookup.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()

[ Upstream commit 6f21c96a78b835259546d8f3fb4edff0f651d478 ]

The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e4c ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.

This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.

ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: beware of alignments in tcp_get_info()

[ Upstream commit ff5d749772018602c47509bdc0093ff72acd82ec ]

With some combinations of user provided flags in netlink command,
it is possible to call tcp_get_info() with a buffer that is not 8-bytes
aligned.

It does matter on some arches, so we need to use put_unaligned() to
store the u64 fields.

Current iproute2 package does not trigger this particular issue.

Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info")
Fixes: 977cb0ecf82e ("tcp: add pacing_rate information into tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

switchdev: Require RTNL mutex to be held when sending FDB notifications

[ Upstream commit 4f2c6ae5c64c353fb1b0425e4747e5603feadba1 ]

When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.

However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.

Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.

Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.

Fixes: 03bf0c281234 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

inet: frag: Always orphan skbs inside ip_defrag()

[ Upstream commit 8282f27449bf15548cb82c77b6e04ee0ab827bdc ]

Later parts of the stack (including fragmentation) expect that there is
never a socket attached to frag in a frag_list, however this invariant
was not enforced on all defrag paths. This could lead to the
BUG_ON(skb->sk) during ip_do_fragment(), as per the call stack at the
end of this commit message.

While the call could be added to openvswitch to fix this particular
error, the head and tail of the frags list are already orphaned
indirectly inside ip_defrag(), so it seems like the remaining fragments
should all be orphaned in all circumstances.

kernel BUG at net/ipv4/ip_output.c:586!
[...]
Call Trace:
 <IRQ>
 [<ffffffffa0205270>] ? do_output.isra.29+0x1b0/0x1b0 [openvswitch]
 [<ffffffffa02167a7>] ovs_fragment+0xcc/0x214 [openvswitch]
 [<ffffffff81667830>] ? dst_discard_out+0x20/0x20
 [<ffffffff81667810>] ? dst_ifdown+0x80/0x80
 [<ffffffffa0212072>] ? find_bucket.isra.2+0x62/0x70 [openvswitch]
 [<ffffffff810e0ba5>] ? mod_timer_pending+0x65/0x210
 [<ffffffff810b732b>] ? __lock_acquire+0x3db/0x1b90
 [<ffffffffa03205a2>] ? nf_conntrack_in+0x252/0x500 [nf_conntrack]
 [<ffffffff810b63c4>] ? __lock_is_held+0x54/0x70
 [<ffffffffa02051a3>] do_output.isra.29+0xe3/0x1b0 [openvswitch]
 [<ffffffffa0206411>] do_execute_actions+0xe11/0x11f0 [openvswitch]
 [<ffffffff810b63c4>] ? __lock_is_held+0x54/0x70
 [<ffffffffa0206822>] ovs_execute_actions+0x32/0xd0 [openvswitch]
 [<ffffffffa020b505>] ovs_dp_process_packet+0x85/0x140 [openvswitch]
 [<ffffffff810b63c4>] ? __lock_is_held+0x54/0x70
 [<ffffffffa02068a2>] ovs_execute_actions+0xb2/0xd0 [openvswitch]
 [<ffffffffa020b505>] ovs_dp_process_packet+0x85/0x140 [openvswitch]
 [<ffffffffa0215019>] ? ovs_ct_get_labels+0x49/0x80 [openvswitch]
 [<ffffffffa0213a1d>] ovs_vport_receive+0x5d/0xa0 [openvswitch]
 [<ffffffff810b732b>] ? __lock_acquire+0x3db/0x1b90
 [<ffffffff810b732b>] ? __lock_acquire+0x3db/0x1b90
 [<ffffffff810b732b>] ? __lock_acquire+0x3db/0x1b90
 [<ffffffffa0214895>] ? internal_dev_xmit+0x5/0x140 [openvswitch]
 [<ffffffffa02148fc>] internal_dev_xmit+0x6c/0x140 [openvswitch]
 [<ffffffffa0214895>] ? internal_dev_xmit+0x5/0x140 [openvswitch]
 [<ffffffff81660299>] dev_hard_start_xmit+0x2b9/0x5e0
 [<ffffffff8165fc21>] ? netif_skb_features+0xd1/0x1f0
 [<ffffffff81660f20>] __dev_queue_xmit+0x800/0x930
 [<ffffffff81660770>] ? __dev_queue_xmit+0x50/0x930
 [<ffffffff810b53f1>] ? mark_held_locks+0x71/0x90
 [<ffffffff81669876>] ? neigh_resolve_output+0x106/0x220
 [<ffffffff81661060>] dev_queue_xmit+0x10/0x20
 [<ffffffff816698e8>] neigh_resolve_output+0x178/0x220
 [<ffffffff816a8e6f>] ? ip_finish_output2+0x1ff/0x590
 [<ffffffff816a8e6f>] ip_finish_output2+0x1ff/0x590
 [<ffffffff816a8cee>] ? ip_finish_output2+0x7e/0x590
 [<ffffffff816a9a31>] ip_do_fragment+0x831/0x8a0
 [<ffffffff816a8c70>] ? ip_copy_metadata+0x1b0/0x1b0
 [<ffffffff816a9ae3>] ip_fragment.constprop.49+0x43/0x80
 [<ffffffff816a9c9c>] ip_finish_output+0x17c/0x340
 [<ffffffff8169a6f4>] ? nf_hook_slow+0xe4/0x190
 [<ffffffff816ab4c0>] ip_output+0x70/0x110
 [<ffffffff816a9b20>] ? ip_fragment.constprop.49+0x80/0x80
 [<ffffffff816aa9f9>] ip_local_out+0x39/0x70
 [<ffffffff816abf89>] ip_send_skb+0x19/0x40
 [<ffffffff816abfe3>] ip_push_pending_frames+0x33/0x40
 [<ffffffff816df21a>] icmp_push_reply+0xea/0x120
 [<ffffffff816df93d>] icmp_reply.constprop.23+0x1ed/0x230
 [<ffffffff816df9ce>] icmp_echo.part.21+0x4e/0x50
 [<ffffffff810b63c4>] ? __lock_is_held+0x54/0x70
 [<ffffffff810d5f9e>] ? rcu_read_lock_held+0x5e/0x70
 [<ffffffff816dfa06>] icmp_echo+0x36/0x70
 [<ffffffff816e0d11>] icmp_rcv+0x271/0x450
 [<ffffffff816a4ca7>] ip_local_deliver_finish+0x127/0x3a0
 [<ffffffff816a4bc1>] ? ip_local_deliver_finish+0x41/0x3a0
 [<ffffffff816a5160>] ip_local_deliver+0x60/0xd0
 [<ffffffff816a4b80>] ? ip_rcv_finish+0x560/0x560
 [<ffffffff816a46fd>] ip_rcv_finish+0xdd/0x560
 [<ffffffff816a5453>] ip_rcv+0x283/0x3e0
 [<ffffffff810b6302>] ? match_held_lock+0x192/0x200
 [<ffffffff816a4620>] ? inet_del_offload+0x40/0x40
 [<ffffffff8165d062>] __netif_receive_skb_core+0x392/0xae0
 [<ffffffff8165e68e>] ? process_backlog+0x8e/0x230
 [<ffffffff810b53f1>] ? mark_held_locks+0x71/0x90
 [<ffffffff8165d7c8>] __netif_receive_skb+0x18/0x60
 [<ffffffff8165e678>] process_backlog+0x78/0x230
 [<ffffffff8165e6dd>] ? process_backlog+0xdd/0x230
 [<ffffffff8165e355>] net_rx_action+0x155/0x400
 [<ffffffff8106b48c>] __do_softirq+0xcc/0x420
 [<ffffffff816a8e87>] ? ip_finish_output2+0x217/0x590
 [<ffffffff8178e78c>] do_softirq_own_stack+0x1c/0x30
 <EOI>
 [<ffffffff8106b88e>] do_softirq+0x4e/0x60
 [<ffffffff8106b948>] __local_bh_enable_ip+0xa8/0xb0
 [<ffffffff816a8eb0>] ip_finish_output2+0x240/0x590
 [<ffffffff816a9a31>] ? ip_do_fragment+0x831/0x8a0
 [<ffffffff816a9a31>] ip_do_fragment+0x831/0x8a0
 [<ffffffff816a8c70>] ? ip_copy_metadata+0x1b0/0x1b0
 [<ffffffff816a9ae3>] ip_fragment.constprop.49+0x43/0x80
 [<ffffffff816a9c9c>] ip_finish_output+0x17c/0x340
 [<ffffffff8169a6f4>] ? nf_hook_slow+0xe4/0x190
 [<ffffffff816ab4c0>] ip_output+0x70/0x110
 [<ffffffff816a9b20>] ? ip_fragment.constprop.49+0x80/0x80
 [<ffffffff816aa9f9>] ip_local_out+0x39/0x70
 [<ffffffff816abf89>] ip_send_skb+0x19/0x40
 [<ffffffff816abfe3>] ip_push_pending_frames+0x33/0x40
 [<ffffffff816d55d3>] raw_sendmsg+0x7d3/0xc30
 [<ffffffff810b732b>] ? __lock_acquire+0x3db/0x1b90
 [<ffffffff816e7557>] ? inet_sendmsg+0xc7/0x1d0
 [<ffffffff810b63c4>] ? __lock_is_held+0x54/0x70
 [<ffffffff816e759a>] inet_sendmsg+0x10a/0x1d0
 [<ffffffff816e7495>] ? inet_sendmsg+0x5/0x1d0
 [<ffffffff8163e398>] sock_sendmsg+0x38/0x50
 [<ffffffff8163ec5f>] ___sys_sendmsg+0x25f/0x270
 [<ffffffff811aadad>] ? handle_mm_fault+0x8dd/0x1320
 [<ffffffff8178c147>] ? _raw_spin_unlock+0x27/0x40
 [<ffffffff810529b2>] ? __do_page_fault+0x1e2/0x460
 [<ffffffff81204886>] ? __fget_light+0x66/0x90
 [<ffffffff8163f8e2>] __sys_sendmsg+0x42/0x80
 [<ffffffff8163f932>] SyS_sendmsg+0x12/0x20
 [<ffffffff8178cb17>] entry_SYSCALL_64_fastpath+0x12/0x6f
Code: 00 00 44 89 e0 e9 7c fb ff ff 4c 89 ff e8 e7 e7 ff ff 41 8b 9d 80 00 00 00 2b 5d d4 89 d8 c1 f8 03 0f b7 c0 e9 33 ff ff f
 66 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 55 48
RIP  [<ffffffff816a9a92>] ip_do_fragment+0x892/0x8a0
 RSP <ffff88006d603170>

Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: fix connection abort during subscription cancel

[ Upstream commit 4d5cfcba2f6ec494d8810b9e3c0a7b06255c8067 ]

In 'commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing
to events")', we terminate the connection if the subscription
creation fails.
In the same commit, the subscription creation result was based on
the value of the subscription pointer (set in the function) instead
of the return code.

Unfortunately, the same function tipc_subscrp_create() handles
subscription cancel request. For a subscription cancellation request,
the subscription pointer cannot be set. Thus if a subscriber has
several subscriptions and cancels any of them, the connection is
terminated.

In this commit, we terminate the connection based on the return value
of tipc_subscrp_create().
Fixes: commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing to events")
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: fix mv88e6xxx switches

[ Upstream commit db0e51afa481088e6396f11e02018d64113a6578 ]

Since commit 76e398a62712 ("net: dsa: use switchdev obj for VLAN add/del
ops"), the Marvell 88E6xxx switch has been unable to pass traffic
between ports - any received traffic is discarded by the switch.
Taking a port out of bridge mode and configuring a vlan on it also the
port to start passing traffic.

With the debugfs files re-instated to allow debug of this issue by
comparing the register settings between the working and non-working
case, the reason becomes clear:

     GLOBAL GLOBAL2 SERDES   0    1    2    3    4    5    6
- 7:  1111    707f    2001     2    2    2    2    2    0    2
+ 7:  1111    707f    2001     1    1    1    1    1    0    1

Register 7 for the ports is the default vlan tag register, and in the
non-working setup, it has been set to 2, despite vlan 2 not being
configured.  This causes the switch to drop all packets coming in to
these ports.  The working setup has the default vlan tag register set
to 1, which is the default vlan when none is configured.

Inspection of the code reveals why.  The code prior to this commit
was:

- for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
- if (!err && vlan->flags & BRIDGE_VLAN_INFO_PVID)
- err = ds->drv->port_pvid_set(ds, p->port, vid);

but the new code is:

+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
+ }
...
+ if (pvid)
+ err = _mv88e6xxx_port_pvid_set(ds, port, vid);

This causes the new code to always set the default vlan to one higher
than the old code.

Fix this.

Fixes: 76e398a62712 ("net: dsa: use switchdev obj for VLAN add/del ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: allow setting SCTP_SACK_IMMEDIATELY by the application

[ Upstream commit 27f7ed2b11d42ab6d796e96533c2076ec220affc ]

This patch extends commit b93d6471748d ("sctp: implement the sender side
for SACK-IMMEDIATELY extension") as it didn't white list
SCTP_SACK_IMMEDIATELY on sctp_msghdr_parse(), causing it to be
understood as an invalid flag and returning -EINVAL to the application.

Note that the actual handling of the flag is already there in
sctp_datamsg_from_user().

https://tools.ietf.org/html/rfc7053#section-7

Fixes: b93d6471748d ("sctp: implement the sender side for SACK-IMMEDIATELY extension")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pptp: fix illegal memory access caused by multiple bind()s

[ Upstream commit 9a368aff9cb370298fa02feeffa861f2db497c18 ]

Several times already this has been reported as kasan reports caused by
syzkaller and trinity and people always looked at RCU races, but it is
much more simple. :)

In case we bind a pptp socket multiple times, we simply add it to
the callid_sock list but don't remove the old binding. Thus the old
socket stays in the bucket with unused call_id indexes and doesn't get
cleaned up. This causes various forms of kasan reports which were hard
to pinpoint.

Simply don't allow multiple binds and correct error handling in
pptp_bind. Also keep sk_state bits in place in pptp_connect.

Fixes: 00959ade36acad ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)")
Cc: Dmitry Kozlov <xeb@mail.ru>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_unix: fix struct pid memory leak

[ Upstream commit fa0dc04df259ba2df3ce1920e9690c7842f8fa4b ]

Dmitry reported a struct pid leak detected by a syzkaller program.

Bug happens in unix_stream_recvmsg() when we break the loop when a
signal is pending, without properly releasing scm.

Fixes: b3ca9b02b007 ("net: fix multithreaded signal handling in unix recv routines")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix NULL deref in tcp_v4_send_ack()

[ Upstream commit e62a123b8ef7c5dc4db2c16383d506860ad21b47 ]

Neal reported crashes with this stack trace :

 RIP: 0010:[<ffffffff8c57231b>] tcp_v4_send_ack+0x41/0x20f
...
 CR2: 0000000000000018 CR3: 000000044005c000 CR4: 00000000001427e0
...
  [<ffffffff8c57258e>] tcp_v4_reqsk_send_ack+0xa5/0xb4
  [<ffffffff8c1a7caa>] tcp_check_req+0x2ea/0x3e0
  [<ffffffff8c19e420>] tcp_rcv_state_process+0x850/0x2500
  [<ffffffff8c1a6d21>] tcp_v4_do_rcv+0x141/0x330
  [<ffffffff8c56cdb2>] sk_backlog_rcv+0x21/0x30
  [<ffffffff8c098bbd>] tcp_recvmsg+0x75d/0xf90
  [<ffffffff8c0a8700>] inet_recvmsg+0x80/0xa0
  [<ffffffff8c17623e>] sock_aio_read+0xee/0x110
  [<ffffffff8c066fcf>] do_sync_read+0x6f/0xa0
  [<ffffffff8c0673a1>] SyS_read+0x1e1/0x290
  [<ffffffff8c5ca262>] system_call_fastpath+0x16/0x1b

The problem here is the skb we provide to tcp_v4_send_ack() had to
be parked in the backlog of a new TCP fastopen child because this child
was owned by the user at the time an out of window packet arrived.

Before queuing a packet, TCP has to set skb->dev to NULL as the device
could disappear before packet is removed from the queue.

Fix this issue by using the net pointer provided by the socket (being a
timewait or a request socket).

IPv6 is immune to the bug : tcp_v6_send_response() already gets the net
pointer from the socket if provided.

Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lwt: fix rx checksum setting for lwt devices tunneling over ipv6

[ Upstream commit c868ee7063bdb53f3ef9eac7bcec84960980b471 ]

the commit 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be
correctly controlled.") changed the default xmit checksum setting
for lwt vxlan/geneve ipv6 tunnels, so that now the checksum is not
set into external UDP header.
This commit changes the rx checksum setting for both lwt vxlan/geneve
devices created by openvswitch accordingly, so that lwt over ipv6
tunnel pairs are again able to communicate with default values.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tunnels: Allow IPv6 UDP checksums to be correctly controlled.

[ Upstream commit 35e2d1152b22eae99c961affbe85374bef05a775 ]

When configuring checksums on UDP tunnels, the flags are different
for IPv4 vs. IPv6 (and reversed). However, when lightweight tunnels
are enabled the flags used are always the IPv4 versions, which are
ignored in the IPv6 code paths. This uses the correct IPv6 flags, so
checksums can be controlled appropriately.

Fixes: a725e514 ("vxlan: metadata based tunneling for IPv6")
Fixes: abe492b4 ("geneve: UDP checksum configuration via netlink")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dp83640: Fix tx timestamp overflow handling.

[ Upstream commit 81e8f2e930fe76b9814c71b9d87c30760b5eb705 ]

PHY status frames are not reliable, the PHY may not be able to send them
during heavy receive traffic. This overflow condition is signaled by the
PHY in the next status frame, but the driver did not make use of it.
Instead it always reported wrong tx timestamps to user space after an
overflow happened because it assigned newly received tx timestamps to old
packets in the queue.

This commit fixes this issue by clearing the tx timestamp queue every time
an overflow happens, so that no timestamps are delivered for overflow
packets. This way time stamping will continue correctly after an overflow.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gro: Make GRO aware of lightweight tunnels.

[ Upstream commit ce87fc6ce3f9f4488546187e3757cf666d9d4a2a ]

GRO is currently not aware of tunnel metadata generated by lightweight
tunnels and stored in the dst. This leads to two possible problems:
 * Incorrectly merging two frames that have different metadata.
 * Leaking of allocated metadata from merged frames.

This avoids those problems by comparing the tunnel information before
merging, similar to how we handle other metadata (such as vlan tags),
and releasing any state when we are done.

Reported-by: John <john.phillips5@hpe.com>
Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

af_iucv: Validate socket address length in iucv_sock_bind()

[ Upstream commit 52a82e23b9f2a9e1d429c5207f8575784290d008 ]

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.3

modules: fix modparam async_probe request

commit 4355efbd80482a961cae849281a8ef866e53d55c upstream.

Commit f2411da746985 ("driver-core: add driver module
asynchronous probe support") added async probe support,
in two forms:

  * in-kernel driver specification annotation
  * generic async_probe module parameter (modprobe foo async_probe)

To support the generic kernel parameter parse_args() was
extended via commit ecc8617053e0 ("module: add extra
argument for parse_params() callback") however commit
failed to f2411da746985 failed to add the required argument.

This causes a crash then whenever async_probe generic
module parameter is used. This was overlooked when the
form in which in-kernel async probe support was reworked
a bit... Fix this as originally intended.

Cc: Hannes Reinecke <hare@suse.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> [minimized]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

module: wrapper for symbol name.

commit 2e7bac536106236104e9e339531ff0fcdb7b8147 upstream.

This trivial wrapper adds clarity and makes the following patch
smaller.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

itimers: Handle relative timers with CONFIG_TIME_LOW_RES proper

commit 51cbb5242a41700a3f250ecfb48dcfb7e4375ea4 upstream.

As Helge reported for timerfd we have the same issue in itimers. We return
remaining time larger than the programmed relative time to user space in case
of CONFIG_TIME_LOW_RES=y. Use the proper function to adjust the extra time
added in hrtimer_start_range_ns().

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Helge Deller <deller@gmx.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: dhowells@redhat.com
Link: http://lkml.kernel.org/r/20160114164159.528222587@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

posix-timers: Handle relative timers with CONFIG_TIME_LOW_RES proper

commit 572c39172684c3711e4a03c9a7380067e2b0661c upstream.

As Helge reported for timerfd we have the same issue in posix timers. We
return remaining time larger than the programmed relative time to user space
in case of CONFIG_TIME_LOW_RES=y. Use the proper function to adjust the extra
time added in hrtimer_start_range_ns().

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Helge Deller <deller@gmx.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: dhowells@redhat.com
Link: http://lkml.kernel.org/r/20160114164159.450510905@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

timerfd: Handle relative timers with CONFIG_TIME_LOW_RES proper

commit b62526ed11a1fe3861ab98d40b7fdab8981d788a upstream.

Helge reported that a relative timer can return a remaining time larger than
the programmed relative time on parisc and other architectures which have
CONFIG_TIME_LOW_RES set. This happens because we add a jiffie to the resulting
expiry time to prevent short timeouts.

Use the new function hrtimer_expires_remaining_adjusted() to calculate the
remaining time. It takes that extra added time into account for relative
timers.

Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: dhowells@redhat.com
Link: http://lkml.kernel.org/r/20160114164159.354500742@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

prctl: take mmap sem for writing to protect against others

commit ddf1d398e517e660207e2c807f76a90df543a217 upstream.

An unprivileged user can trigger an oops on a kernel with
CONFIG_CHECKPOINT_RESTORE.

proc_pid_cmdline_read takes mmap_sem for reading and obtains args + env
start/end values. These get sanity checked as follows:
        BUG_ON(arg_start > arg_end);
        BUG_ON(env_start > env_end);

These can be changed by prctl_set_mm. Turns out also takes the semaphore for
reading, effectively rendering it useless. This results in:

  kernel BUG at fs/proc/base.c:240!
  invalid opcode: 0000 [#1] SMP
  Modules linked in: virtio_net
  CPU: 0 PID: 925 Comm: a.out Not tainted 4.4.0-rc8-next-20160105dupa+ #71
  Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
  task: ffff880077a68000 ti: ffff8800784d0000 task.ti: ffff8800784d0000
  RIP: proc_pid_cmdline_read+0x520/0x530
  RSP: 0018:ffff8800784d3db8  EFLAGS: 00010206
  RAX: ffff880077c5b6b0 RBX: ffff8800784d3f18 RCX: 0000000000000000
  RDX: 0000000000000002 RSI: 00007f78e8857000 RDI: 0000000000000246
  RBP: ffff8800784d3e40 R08: 0000000000000008 R09: 0000000000000001
  R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000050
  R13: 00007f78e8857800 R14: ffff88006fcef000 R15: ffff880077c5b600
  FS:  00007f78e884a740(0000) GS:ffff88007b200000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
  CR2: 00007f78e8361770 CR3: 00000000790a5000 CR4: 00000000000006f0
  Call Trace:
    __vfs_read+0x37/0x100
    vfs_read+0x82/0x130
    SyS_read+0x58/0xd0
    entry_SYSCALL_64_fastpath+0x12/0x76
  Code: 4c 8b 7d a8 eb e9 48 8b 9d 78 ff ff ff 4c 8b 7d 90 48 8b 03 48 39 45 a8 0f 87 f0 fe ff ff e9 d1 fe ff ff 4c 8b 7d 90 eb c6 0f 0b <0f> 0b 0f 0b 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
  RIP   proc_pid_cmdline_read+0x520/0x530
  ---[ end trace 97882617ae9c6818 ]---

Turns out there are instances where the code just reads aformentioned
values without locking whatsoever - namely environ_read and get_cmdline.

Interestingly these functions look quite resilient against bogus values,
but I don't believe this should be relied upon.

The first patch gets rid of the oops bug by grabbing mmap_sem for
writing.

The second patch is optional and puts locking around aformentioned
consumers for safety.  Consumers of other fields don't seem to benefit
from similar treatment and are left untouched.

This patch (of 2):

The code was taking the semaphore for reading, which does not protect
against readers nor concurrent modifications.

The problem could cause a sanity checks to fail in procfs's cmdline
reader, resulting in an OOPS.

Note that some functions perform an unlocked read of various mm fields,
but they seem to be fine despite possible modificaton.

Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Jan Stancek <jstancek@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anshuman Khandual <anshuman.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: log mount failures don't wait for buffers to be released

commit 85bec5460ad8e05e0a8d70fb0f6750eb719ad092 upstream.

Recently I've been seeing xfs/051 fail on 1k block size filesystems.
Trying to trace the events during the test lead to the problem going
away, indicating that it was a race condition that lead to this
ASSERT failure:

XFS: Assertion failed: atomic_read(&pag->pag_ref) == 0, file: fs/xfs/xfs_mount.c, line: 156
.....
[<ffffffff814e1257>] xfs_free_perag+0x87/0xb0
[<ffffffff814e21b9>] xfs_mountfs+0x4d9/0x900
[<ffffffff814e5dff>] xfs_fs_fill_super+0x3bf/0x4d0
[<ffffffff811d8800>] mount_bdev+0x180/0x1b0
[<ffffffff814e3ff5>] xfs_fs_mount+0x15/0x20
[<ffffffff811d90a8>] mount_fs+0x38/0x170
[<ffffffff811f4347>] vfs_kern_mount+0x67/0x120
[<ffffffff811f7018>] do_mount+0x218/0xd60
[<ffffffff811f7e5b>] SyS_mount+0x8b/0xd0

When I finally caught it with tracing enabled, I saw that AG 2 had
an elevated reference count and a buffer was responsible for it. I
tracked down the specific buffer, and found that it was missing the
final reference count release that would put it back on the LRU and
hence be found by xfs_wait_buftarg() calls in the log mount failure
handling.

The last four traces for the buffer before the assert were (trimmed
for relevance)

kworker/0:1-5259   xfs_buf_iodone:        hold 2  lock 0 flags ASYNC
kworker/0:1-5259   xfs_buf_ioerror:       hold 2  lock 0 error -5
mount-7163    xfs_buf_lock_done:     hold 2  lock 0 flags ASYNC
mount-7163    xfs_buf_unlock:        hold 2  lock 1 flags ASYNC

This is an async write that is completing, so there's nobody waiting
for it directly.  Hence we call xfs_buf_relse() once all the
processing is complete. That does:

static inline void xfs_buf_relse(xfs_buf_t *bp)
{
xfs_buf_unlock(bp);
xfs_buf_rele(bp);
}

Now, it's clear that mount is waiting on the buffer lock, and that
it has been released by xfs_buf_relse() and gained by mount. This is
expected, because at this point the mount process is in
xfs_buf_delwri_submit() waiting for all the IO it submitted to
complete.

The mount process, however, is waiting on the lock for the buffer
because it is in xfs_buf_delwri_submit(). This waits for IO
completion, but it doesn't wait for the buffer reference owned by
the IO to go away. The mount process collects all the completions,
fails the log recovery, and the higher level code then calls
xfs_wait_buftarg() to free all the remaining buffers in the
filesystem.

The issue is that on unlocking the buffer, the scheduler has decided
that the mount process has higher priority than the the kworker
thread that is running the IO completion, and so immediately
switched contexts to the mount process from the semaphore unlock
code, hence preventing the kworker thread from finishing the IO
completion and releasing the IO reference to the buffer.

Hence by the time that xfs_wait_buftarg() is run, the buffer still
has an active reference and so isn't on the LRU list that the
function walks to free the remaining buffers. Hence we miss that
buffer and continue onwards to tear down the mount structures,
at which time we get find a stray reference count on the perag
structure. On a non-debug kernel, this will be ignored and the
structure torn down and freed. Hence when the kworker thread is then
rescheduled and the buffer released and freed, it will access a
freed perag structure.

The problem here is that when the log mount fails, we still need to
quiesce the log to ensure that the IO workqueues have returned to
idle before we run xfs_wait_buftarg(). By synchronising the
workqueues, we ensure that all IO completions are fully processed,
not just to the point where buffers have been unlocked. This ensures
we don't end up in the situation above.

Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "xfs: clear PF_NOFREEZE for xfsaild kthread"

commit 3e85286e75224fa3f08bdad20e78c8327742634e upstream.

This reverts commit 24ba16bb3d499c49974669cd8429c3e4138ab102 as it
prevents machines from suspending. This regression occurs when the
xfsaild is idle on entry to suspend, and so there s no activity to
wake it from it's idle sleep and hence see that it is supposed to
freeze. Hence the freezer times out waiting for it and suspend is
cancelled.

There is no obvious fix for this short of freezing the filesystem
properly, so revert this change for now.

Signed-off-by: Dave Chinner <david@fromorbit.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfs: inode recovery readahead can race with inode buffer creation

commit b79f4a1c68bb99152d0785ee4ea3ab4396cdacc6 upstream.

When we do inode readahead in log recovery, we do can do the
readahead before we've replayed the icreate transaction that stamps
the buffer with inode cores. The inode readahead verifier catches
this and marks the buffer as !done to indicate that it doesn't yet
contain valid inodes.

In adding buffer error notification  (i.e. setting b_error = -EIO at
the same time as as we clear the done flag) to such a readahead
verifier failure, we can then get subsequent inode recovery failing
with this error:

XFS (dm-0): metadata I/O error: block 0xa00060 ("xlog_recover_do..(read#2)") error 5 numblks 32

This occurs when readahead completion races with icreate item replay
such as:

inode readahead
find buffer
lock buffer
submit RA io
....
icreate recovery
    xfs_trans_get_buffer
find buffer
lock buffer
<blocks on RA completion>
.....
<ra completion>
fails verifier
clear XBF_DONE
set bp->b_error = -EIO
release and unlock buffer
<icreate gains lock>
icreate initialises buffer
marks buffer as done
adds buffer to delayed write queue
releases buffer

At this point, we have an initialised inode buffer that is up to
date but has an -EIO state registered against it. When we finally
get to recovering an inode in that buffer:

inode item recovery
    xfs_trans_read_buffer
find buffer
lock buffer
sees XBF_DONE is set, returns buffer
    sees bp->b_error is set
fail log recovery!

Essentially, we need xfs_trans_get_buf_map() to clear the error status of
the buffer when doing a lookup. This function returns uninitialised
buffers, so the buffer returned can not be in an error state and
none of the code that uses this function expects b_error to be set
on return. Indeed, there is an ASSERT(!bp->b_error); in the
transaction case in xfs_trans_get_buf_map() that would have caught
this if log recovery used transactions....

This patch firstly changes the inode readahead failure to set -EIO
on the buffer, and secondly changes xfs_buf_get_map() to never
return a buffer with an error state set so this first change doesn't
cause unexpected log recovery failures.

Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libxfs: pack the agfl header structure so XFS_AGFL_SIZE is correct

commit 96f859d52bcb1c6ea6f3388d39862bf7143e2f30 upstream.

Because struct xfs_agfl is 36 bytes long and has a 64-bit integer
inside it, gcc will quietly round the structure size up to the nearest
64 bits -- in this case, 40 bytes.  This results in the XFS_AGFL_SIZE
macro returning incorrect results for v5 filesystems on 64-bit
machines (118 items instead of 119).  As a result, a 32-bit xfs_repair
will see garbage in AGFL item 119 and complain.

Therefore, tell gcc not to pad the structure so that the AGFL size
calculation is correct.

Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: setattr: check permissions before copy-up

commit cf9a6784f7c1b5ee2b9159a1246e327c331c5697 upstream.

Without this copy-up of a file can be forced, even without actually being
allowed to do anything on the file.

[Arnd Bergmann] include <linux/pagemap.h> for PAGE_CACHE_SIZE (used by
MAX_LFS_FILESIZE definition).

Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: root: copy attr

commit ed06e069775ad9236087594a1c1667367e983fb5 upstream.

We copy i_uid and i_gid of underlying inode into overlayfs inode.  Except
for the root inode.

Fix this omission.

Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: check dentry positiveness in ovl_cleanup_whiteouts()

commit 84889d49335627bc770b32787c1ef9ebad1da232 upstream.

This patch fixes kernel crash at removing directory which contains
whiteouts from lower layers.

Cache of directory content passed as "list" contains entries from all
layers, including whiteouts from lower layers. So, lookup in upper dir
(moved into work at this stage) will return negative entry. Plus this
cache is filled long before and we can race with external removal.

Example:
 mkdir -p lower0/dir lower1/dir upper work overlay
 touch lower0/dir/a lower0/dir/b
 mknod lower1/dir/a c 0 0
 mount -t overlay none overlay -o lowerdir=lower1:lower0,upperdir=upper,workdir=work
 rm -fr overlay/dir

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: use a minimal buffer in ovl_copy_xattr

commit e4ad29fa0d224d05e08b2858e65f112fd8edd4fe upstream.

Rather than always allocating the high-order XATTR_SIZE_MAX buffer
which is costly and prone to failure, only allocate what is needed and
realloc if necessary.

Fixes https://github.com/coreos/bugs/issues/489

Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: allow zero size xattr

commit 97daf8b97ad6f913a34c82515be64dc9ac08d63e upstream.

When ovl_copy_xattr() encountered a zero size xattr no more xattrs were
copied and the function returned success.  This is clearly not the desired
behavior.

Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

futex: Drop refcount if requeue_pi() acquired the rtmutex

commit fb75a4282d0d9a3c7c44d940582c2d226cf3acfb upstream.

If the proxy lock in the requeue loop acquires the rtmutex for a
waiter then it acquired also refcount on the pi_state related to the
futex, but the waiter side does not drop the reference count.

Add the missing free_pi_state() call.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Bhuvanesh_Surachari@mentor.com
Cc: Andy Lowe <Andy_Lowe@mentor.com>
Link: http://lkml.kernel.org/r/20151219200607.178132067@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_memremap_release(): fix memremap'd addr handling

commit 9273a8bbf58a15051e53a777389a502420ddc60e upstream.

The pmem driver calls devm_memremap() to map a persistent memory range.
When the pmem driver is unloaded, this memremap'd range is not released
so the kernel will leak a vma.

Fix devm_memremap_release() to handle a given memremap'd address
properly.

Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipc/shm: handle removed segments gracefully in shm_mmap()

commit 1ac0b6dec656f3f78d1c3dd216fad84cb4d0a01e upstream.

remap_file_pages(2) emulation can reach file which represents removed
IPC ID as long as a memory segment is mapped.  It breaks expectations of
IPC subsystem.

Test case (rewritten to be more human readable, originally autogenerated
by syzkaller[1]):

#define _GNU_SOURCE
#include <stdlib.h>
#include <sys/ipc.h>
#include <sys/mman.h>
#include <sys/shm.h>

#define PAGE_SIZE 4096

int main()
{
int id;
void *p;

id = shmget(IPC_PRIVATE, 3 * PAGE_SIZE, 0);
p = shmat(id, NULL, 0);
shmctl(id, IPC_RMID, NULL);
remap_file_pages(p, 3 * PAGE_SIZE, 0, 7, 0);

        return 0;
}

The patch changes shm_mmap() and code around shm_lock() to propagate
locking error back to caller of shm_mmap().

[1] http://github.com/google/syzkaller

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

intel_scu_ipcutil: underflow in scu_reg_access()

commit b1d353ad3d5835b16724653b33c05124e1b5acf1 upstream.

"count" is controlled by the user and it can be negative.  Let's prevent
that by making it unsigned.  You have to have CAP_SYS_RAWIO to call this
function so the bug is not as serious as it could be.

Fixes: 5369c02d951a ('intel_scu_ipc: Utility driver for intel scu ipc')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm,thp: khugepaged: call pte flush at the time of collapse

commit 6a6ac72fd6ea32594b316513e1826c3f6db4cc93 upstream.

This showed up on ARC when running LMBench bw_mem tests as Overlapping
TLB Machine Check Exception triggered due to STLB entry (2M pages)
overlapping some NTLB entry (regular 8K page).

bw_mem 2m touches a large chunk of vaddr creating NTLB entries.  In the
interim khugepaged kicks in, collapsing the contiguous ptes into a
single pmd.  pmdp_collapse_flush()->flush_pmd_tlb_range() is called to
flush out NTLB entries for the ptes.  This for ARC (by design) can only
shootdown STLB entries (for pmd).  The stray NTLB entries cause the
overlap with the subsequent STLB entry for collapsed page.  So make
pmdp_collapse_flush() call pte flush interface not pmd flush.

Note that originally all thp flush call sites in generic code called
flush_tlb_range() leaving it to architecture to implement the flush for
pte and/or pmd.  Commit 12ebc1581ad11454 changed this by calling a new
opt-in API flush_pmd_tlb_range() which made the semantics more explicit
but failed to distinguish the pte vs pmd flush in generic code, which is
what this patch fixes.

Note that ARC can fixed w/o touching the generic pmdp_collapse_flush()
by defining a ARC version, but that defeats the purpose of generic
version, plus sementically this is the right thing to do.

Fixes STAR 9000961194: LMBench on AXS103 triggering duplicate TLB
exceptions with super pages

Fixes: 12ebc1581ad11454 ("mm,thp: introduce flush_pmd_tlb_range")
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dump_stack: avoid potential deadlocks

commit d7ce36924344ace0dbdc855b1206cacc46b36d45 upstream.

Some servers experienced fatal deadlocks because of a combination of
bugs, leading to multiple cpus calling dump_stack().

The checksumming bug was fixed in commit 34ae6a1aa054 ("ipv6: update
skb->csum when CE mark is propagated").

The second problem is a faulty locking in dump_stack()

CPU1 runs in process context and calls dump_stack(), grabs dump_lock.

   CPU2 receives a TCP packet under softirq, grabs socket spinlock, and
   call dump_stack() from netdev_rx_csum_fault().

   dump_stack() spins on atomic_cmpxchg(&dump_lock, -1, 2), since
   dump_lock is owned by CPU1

While dumping its stack, CPU1 is interrupted by a softirq, and happens
to process a packet for the TCP socket locked by CPU2.

CPU1 spins forever in spin_lock() : deadlock

Stack trace on CPU1 looked like :

    NMI backtrace for cpu 1
    RIP: _raw_spin_lock+0x25/0x30
    ...
    Call Trace:
      <IRQ>
      tcp_v6_rcv+0x243/0x620
      ip6_input_finish+0x11f/0x330
      ip6_input+0x38/0x40
      ip6_rcv_finish+0x3c/0x90
      ipv6_rcv+0x2a9/0x500
      process_backlog+0x461/0xaa0
      net_rx_action+0x147/0x430
      __do_softirq+0x167/0x2d0
      call_softirq+0x1c/0x30
      do_softirq+0x3f/0x80
      irq_exit+0x6e/0xc0
      smp_call_function_single_interrupt+0x35/0x40
      call_function_single_interrupt+0x6a/0x70
      <EOI>
      printk+0x4d/0x4f
      printk_address+0x31/0x33
      print_trace_address+0x33/0x3c
      print_context_stack+0x7f/0x119
      dump_trace+0x26b/0x28e
      show_trace_log_lvl+0x4f/0x5c
      show_stack_log_lvl+0x104/0x113
      show_stack+0x42/0x44
      dump_stack+0x46/0x58
      netdev_rx_csum_fault+0x38/0x3c
      __skb_checksum_complete_head+0x6e/0x80
      __skb_checksum_complete+0x11/0x20
      tcp_rcv_established+0x2bd5/0x2fd0
      tcp_v6_do_rcv+0x13c/0x620
      sk_backlog_rcv+0x15/0x30
      release_sock+0xd2/0x150
      tcp_recvmsg+0x1c1/0xfc0
      inet_recvmsg+0x7d/0x90
      sock_recvmsg+0xaf/0xe0
      ___sys_recvmsg+0x111/0x3b0
      SyS_recvmsg+0x5c/0xb0
      system_call_fastpath+0x16/0x1b

Fixes: b58d977432c8 ("dump_stack: serialize the output from dump_stack()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>