Programming Languages Research Group: Git - firefly-linux-kernel-4.4.55.git/log

mtd: spi-nor: remove micron_quad_enable()

commit 3b5394a3ccffbfa1d1d448d48742853a862822c4 upstream.

This patch remove the micron_quad_enable() function which force the Quad
SPI mode. However, once this mode is enabled, the Micron memory expect ALL
commands to use the SPI 4-4-4 protocol. Hence a failure does occur when
calling spi_nor_wait_till_ready() right after the update of the Enhanced
Volatile Configuration Register (EVCR) in the micron_quad_enable() as
the SPI controller driver is not aware about the protocol change.

Since there is almost no performance increase using Fast Read 4-4-4
commands instead of Fast Read 1-1-4 commands, we rather keep on using the
Extended SPI mode than enabling the Quad SPI mode.

Let's take the example of the pretty standard use of 8 dummy cycles during
Fast Read operations on 64KB erase sectors:

Fast Read 1-1-4 requires 8 cycles for the command, then 24 cycles for the
3byte address followed by 8 dummy clock cycles and finally 65536*2 cycles
for the read data; so 131112 clock cycles.

On the other hand the Fast Read 4-4-4 would require 2 cycles for the
command, then 6 cycles for the 3byte address followed by 8 dummy clock
cycles and finally 65536*2 cycles for the read data. So 131088 clock
cycles. The theorical bandwidth increase is 0.0%.

Now using Fast Read operations on 512byte pages:
Fast Read 1-1-4 needs 8+24+8+(512*2) = 1064 clock cycles whereas Fast
Read 4-4-4 would requires 2+6+8+(512*2) = 1040 clock cycles. Hence the
theorical bandwidth increase is 2.3%.
Consecutive reads for non sequential pages is not a relevant use case so
The Quad SPI mode is not worth it.

mtd_speedtest seems to confirm these figures.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 548cd3ab54da ("mtd: spi-nor: Add quad I/O support for Micron SPI NOR")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sh-sci: Remove cpufreq notifier to fix crash/deadlock

commit ff1cab374ad98f4b9f408525ca9c08992b4ed784 upstream.

The BSP team noticed that there is spin/mutex lock issue on sh-sci when
CPUFREQ is used.  The issue is that the notifier function may call
mutex_lock() while the spinlock is held, which can lead to a BUG().
This may happen if CPUFREQ is changed while another CPU calls
clk_get_rate().

Taking the spinlock was added to the notifier function in commit
e552de2413edad1a ("sh-sci: add platform device private data"), to
protect the list of serial ports against modification during traversal.
At that time the Common Clock Framework didn't exist yet, and
clk_get_rate() just returned clk->rate without taking a mutex.
Note that since commit d535a2305facf9b4 ("serial: sh-sci: Require a
device per port mapping."), there's no longer a list of serial ports to
traverse, and taking the spinlock became superfluous.

To fix the issue, just remove the cpufreq notifier:
  1. The notifier doesn't work correctly: all it does is update stored
     clock rates; it does not update the divider in the hardware.
     The divider will only be updated when calling sci_set_termios().
     I believe this was broken back in 2004, when the old
     drivers/char/sh-sci.c driver (where the notifier did update the
     divider) was replaced by drivers/serial/sh-sci.c (where the
     notifier just updated port->uartclk).
     Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port
     sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH]
     Remove old sh-sci driver").
  2. On modern SoCs, the sh-sci parent clock rate is no longer related
     to the CPU clock rate anyway, so using a cpufreq notifier is
     futile.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix NULL pointer dereference in ext4_mark_inode_dirty()

commit 5e1021f2b6dff1a86a468a1424d59faae2bc63c1 upstream.

ext4_reserve_inode_write() in ext4_mark_inode_dirty() could fail on
error (e.g. EIO) and iloc.bh can be NULL in this case. But the error is
ignored in the following "if" condition and ext4_expand_extra_isize()
might be called with NULL iloc.bh set, which triggers NULL pointer
dereference.

This is uncovered by commit 8b4953e13f4c ("ext4: reserve code points for
the project quota feature"), which enlarges the ext4_inode size, and
run the following script on new kernel but with old mke2fs:

  #/bin/bash
  mnt=/mnt/ext4
  devname=ext4-error
  dev=/dev/mapper/$devname
  fsimg=/home/fs.img

  trap cleanup 0 1 2 3 9 15

  cleanup()
  {
          umount $mnt >/dev/null 2>&1
          dmsetup remove $devname
          losetup -d $backend_dev
          rm -f $fsimg
          exit 0
  }

  rm -f $fsimg
  fallocate -l 1g $fsimg
  backend_dev=`losetup -f --show $fsimg`
  devsize=`blockdev --getsz $backend_dev`

  good_tab="0 $devsize linear $backend_dev 0"
  error_tab="0 $devsize error $backend_dev 0"

  dmsetup create $devname --table "$good_tab"

  mkfs -t ext4 $dev
  mount -t ext4 -o errors=continue,strictatime $dev $mnt

  dmsetup load $devname --table "$error_tab" && dmsetup resume $devname
  echo 3 > /proc/sys/vm/drop_caches
  ls -l $mnt
  exit 0

[ Patch changed to simplify the function a tiny bit. -- Ted ]

Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm/kmmio: Fix mmiotrace for hugepages

commit cfa52c0cfa4d727aa3e457bf29aeff296c528a08 upstream.

Because Linux might use bigger pages than the 4K pages to handle those mmio
ioremaps, the kmmio code shouldn't rely on the pade id as it currently does.

Using the memory address instead of the page id lets us look up how big the
page is and what its base address is, so that we won't get a page fault
within the same page twice anymore.

Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-mm@kvack.org
Cc: linux-x86_64@vger.kernel.org
Cc: nouveau@lists.freedesktop.org
Cc: pq@iki.fi
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/1456966991-6861-1-git-send-email-nouveau@karolherbst.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf evlist: Reference count the cpu and thread maps at set_maps()

commit a55e5663761366fb883f6f25375dd68bc958b9db upstream.

We were dropping the reference we possibly held but not obtaining one
for the new maps, which we will drop at perf_evlist__delete(), fix it.

This was caught by Steven Noonan in some of the machines which would
produce this output when caught by glibc debug mechanisms:

  $ sudo perf test 21
  21: Test object code reading                                 :***
  Error in `perf': corrupted double-linked list: 0x00000000023ffcd0 ***
  ======= Backtrace: =========
  /usr/lib/libc.so.6(+0x72055)[0x7f25be0f3055]
  /usr/lib/libc.so.6(+0x779b6)[0x7f25be0f89b6]
  /usr/lib/libc.so.6(+0x7a0ed)[0x7f25be0fb0ed]
  /usr/lib/libc.so.6(__libc_calloc+0xba)[0x7f25be0fceda]
  perf(parse_events_lex_init_extra+0x38)[0x4cfff8]
  perf(parse_events+0x55)[0x4a0615]
  perf(perf_evlist__config+0xcf)[0x4eeb2f]
  perf[0x479f82]
  perf(test__code_reading+0x1e)[0x47ad4e]
  perf(cmd_test+0x5dd)[0x46452d]
  perf[0x47f4e3]
  perf(main+0x603)[0x42c723]
  /usr/lib/libc.so.6(__libc_start_main+0xf0)[0x7f25be0a1610]
  perf(_start+0x29)[0x42c859]

Further investigation using valgrind led to the reference count imbalance fixed
in this patch.

Reported-and-Tested-by: Steven Noonan <steven@uplinklabs.net>
Link: http://lkml.kernel.org/r/CAKbGBLjC2Dx5vshxyGmQkcD+VwiAQLbHoXA9i7kvRB2-2opHZQ@mail.gmail.com
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: f30a79b012e5 ("perf tools: Add reference counting for cpu_map object")
Link: http://lkml.kernel.org/n/tip-j0u1bdhr47sa511sgg76kb8h@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/misc/ad525x_dpot: AD5274 fix RDAC read back errors

commit f3df53e4d70b5736368a8fe8aa1bb70c1cb1f577 upstream.

Fix RDAC read back errors caused by a typo. Value must shift by 2.

Fixes: a4bd394956f2 ("drivers/misc/ad525x_dpot.c: new features")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: max77686: Properly handle regmap_irq_get_virq() error code

commit fb166ba1d7f0a662f7332f4ff660a0d6f4d76915 upstream.

The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.

This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d933 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: rx8025: remove rv8803 id

commit aaa3cee5deffa28415a6e1852c5afae0f5d210e2 upstream.

The rv8803 has its own driver that should be used. Remove its id from
the rx8025 driver.

Fixes: b1f9d790b59dc04f8813a49a92ddd8651770ffee
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: ds1685: passing bogus values to irq_restore

commit 8c09b9fdecab1f4a289f07b46e2ad174b6641928 upstream.

We call spin_lock_irqrestore with "flags" set to zero instead of to the
value from spin_lock_irqsave().

Fixes: aaaf5fbf56f1 ('rtc: add driver for DS1685 family of real time clocks')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: vr41xx: Wire up alarm_irq_enable

commit a25f4a95ec3cded34c1250364eba704c5e4fdac4 upstream.

drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used

Apparently the conversion to alarm_irq_enable forgot to wire up the
callback.

Fixes: 16380c153a69c378 ("RTC: Convert rtc drivers to use the alarm_irq_enable method")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: hym8563: fix invalid year calculation

commit d5861262210067fc01b2fb4f7af2fd85a3453f15 upstream.

Year field must be in BCD format, according to
hym8563 datasheet.

Due to the bug year 2016 became 2010.

Fixes: dcaf03849352 ("rtc: add hym8563 rtc-driver")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / Domains: Fix removal of a subdomain

commit beda5fc1ff9b527059290a97b672d2ee0eb7b92f upstream.

Commit 30e7a65b3fdb (PM / Domains: Ensure subdomain is not in use
before removing) added a test to ensure that a subdomain is not a
master to another subdomain or if any devices are using the subdomain
before removing. This change incorrectly used the "slave_links" list to
determine if the subdomain is a master to another subdomain, where it
should have been using the "master_links" list instead. The
"slave_links" list will never be empty for a subdomain and so a
subdomain can never be removed. Fix this by testing if the
"master_links" list is empty instead.

Fixes: 30e7a65b3fdb (PM / Domains: Ensure subdomain is not in use before removing)
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / OPP: Initialize u_volt_min/max to a valid value

commit c88c395f4a6485f23f81e385c79945d68bcd5c5d upstream.

We kept u_volt_min/max initialized to 0, when only the target voltage is
present in DT, instead of the target/min/max triplet.

This didn't go well with the regulator framework, as on few calls the
min voltage was set to target and max was set to 0 and so resulted in a
kernel crash like below:

kernel BUG at ../drivers/regulator/core.c:216!

[<c0684af4>] (regulator_check_voltage) from [<c06857ac>] (regulator_set_voltage_unlocked+0x58/0x230)
[<c06857ac>] (regulator_set_voltage_unlocked) from [<c06859ac>] (regulator_set_voltage+0x28/0x54)
[<c06859ac>] (regulator_set_voltage) from [<c0775b28>] (_set_opp_voltage+0x30/0x98)
[<c0775b28>] (_set_opp_voltage) from [<c0776630>] (dev_pm_opp_set_rate+0xf0/0x28c)
[<c0776630>] (dev_pm_opp_set_rate) from [<c096f784>] (__cpufreq_driver_target+0x184/0x2b4)
[<c096f784>] (__cpufreq_driver_target) from [<c0973760>] (dbs_check_cpu+0x1b0/0x1f4)
[<c0973760>] (dbs_check_cpu) from [<c0973f30>] (cpufreq_governor_dbs+0x324/0x5c4)
[<c0973f30>] (cpufreq_governor_dbs) from [<c0970958>] (__cpufreq_governor+0xe4/0x1ec)
[<c0970958>] (__cpufreq_governor) from [<c09711e0>] (cpufreq_init_policy+0x64/0x8c)
[<c09711e0>] (cpufreq_init_policy) from [<c09718cc>] (cpufreq_online+0x2fc/0x708)
[<c09718cc>] (cpufreq_online) from [<c0765ff0>] (subsys_interface_register+0x94/0xd8)
[<c0765ff0>] (subsys_interface_register) from [<c0970530>] (cpufreq_register_driver+0x14c/0x19c)
[<c0970530>] (cpufreq_register_driver) from [<c09746dc>] (dt_cpufreq_probe+0x70/0xec)
[<c09746dc>] (dt_cpufreq_probe) from [<c076907c>] (platform_drv_probe+0x4c/0xb0)
[<c076907c>] (platform_drv_probe) from [<c07678e0>] (driver_probe_device+0x214/0x2c0)
[<c07678e0>] (driver_probe_device) from [<c0767a18>] (__driver_attach+0x8c/0x90)
[<c0767a18>] (__driver_attach) from [<c0765c2c>] (bus_for_each_dev+0x68/0x9c)
[<c0765c2c>] (bus_for_each_dev) from [<c0766d78>] (bus_add_driver+0x1a0/0x218)
[<c0766d78>] (bus_add_driver) from [<c076810c>] (driver_register+0x78/0xf8)
[<c076810c>] (driver_register) from [<c0301d74>] (do_one_initcall+0x90/0x1d8)
[<c0301d74>] (do_one_initcall) from [<c1100e14>] (kernel_init_freeable+0x15c/0x1fc)
[<c1100e14>] (kernel_init_freeable) from [<c0b27a0c>] (kernel_init+0x8/0xf0)
[<c0b27a0c>] (kernel_init) from [<c0307d78>] (ret_from_fork+0x14/0x3c)
Code: e1550004 baffffeb e3a00000 e8bd8070 (e7f001f2)

Fix that by initializing u_volt_min/max to the target voltage in such cases.

Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 274659029c9d (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

misc: mic/scif: fix wrap around tests

commit 7b64dbf849abdd7e769820e25120758f956a7f13 upstream.

Signed integer overflow is undefined. Also I added a check for
"(offset < 0)" in scif_unregister() because that makes it match the
other conditions and because I didn't want to subtract a negative.

Fixes: ba612aa8b487 ('misc: mic: SCIF memory registration and unregistration')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

misc/bmp085: Enable building as a module

commit 50e6315dba721cbc24ccd6d7b299f1782f210a98 upstream.

Commit 985087dbcb02 'misc: add support for bmp18x chips to the bmp085
driver' changed the BMP085 config symbol to a boolean. I see no
reason why the shared code cannot be built as a module, so change it
back to tristate.

Fixes: 985087dbcb02 ("misc: add support for bmp18x chips to the bmp085 driver")
Cc: Eric Andersson <eric.andersson@unixphere.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/mpi: Endianness fix

commit 3ee0cb5fb5eea2110db1b5cb7f67029b7be8a376 upstream.

The limbs are integers in the host endianness, so we can't simply
iterate over the individual bytes. The current code happens to work on
little-endian, because the order of the limbs in the MPI array is the
same as the order of the bytes in each limb, but it breaks on
big-endian.

Fixes: 0f74fbf77d45 ("MPI: Fix mpi_read_buffer")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: da8xx-fb: fix videomodes of lcd panels

commit 713fced8d10fa1c759c8fb6bf9aaa681bae68cad upstream.

Commit 028cd86b794f4a ("video: da8xx-fb: fix the polarities of the
hsync/vsync pulse") fixes polarities of HSYNC/VSYNC pulse but
forgot to update known_lcd_panels[] which had sync values
according to old logic. This breaks LCD at least on DA850 EVM.

This patch fixes this issue and I have tested this for panel
"Sharp_LK043T1DG01" using DA850 EVM board.

Fixes: 028cd86b794f4a ("video: da8xx-fb: fix the polarities of the hsync/vsync pulse")
Signed-off-by: Sushaanth Srirangapathi <sushaanth.s@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi_dh: force modular build if SCSI is a module

commit 0c994c03c926d26ce48e6bbabbbe60366044fcae upstream.

When the scsi_dh core was moved into the scsi core module,
CONFIG_SCSI_DH became a 'bool' option, and now anything depending on it
can be built-in even when CONFIG_SCSI=m. This of course cannot link
successfully:

drivers/scsi/built-in.o: In function `rdac_init':
scsi_dh_alua.c:(.init.text+0x14): undefined reference to `scsi_register_device_handler'
scsi_dh_alua.c:(.init.text+0x64): undefined reference to `scsi_unregister_device_handler'
drivers/scsi/built-in.o: In function `alua_init':
scsi_dh_alua.c:(.init.text+0xb0): undefined reference to `scsi_register_device_handler'

As a workaround, this adds an extra dependency on CONFIG_SCSI, so
Kconfig can figure out whether built-in is allowed or not.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 086b91d052eb ("scsi_dh: integrate into the core SCSI code")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

paride: make 'verbose' parameter an 'int' again

commit dec63a4dec2d6d01346fd5d96062e67c0636852b upstream.

gcc-6.0 found an ancient bug in the paride driver, which had a
"module_param(verbose, bool, 0);" since before 2.6.12, but actually uses
it to accept '0', '1' or '2' as arguments:

  drivers/block/paride/pd.c: In function 'pd_init_dev_parms':
  drivers/block/paride/pd.c:298:29: warning: comparison of constant '1' with boolean expression is always false [-Wbool-compare]
   #define DBMSG(msg) ((verbose>1)?(msg):NULL)

In 2012, Rusty did a cleanup patch that also changed the type of the
variable to 'bool', which introduced what is now a gcc warning.

This changes the type back to 'int' and adapts the module_param() line
instead, so it should work as documented in case anyone ever cares about
running the ancient driver with debugging.

Fixes: 90ab5ee94171 ("module_param: make bool parameters really bool (drivers & misc)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rusty Russell <rusty@rustcorp.com.au>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: s5m8767: fix get_register() error handling

commit e07ff9434167981c993a26d2edbbcb8e13801dbb upstream.

The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:

drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.

In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c4c60554acf ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/mxs: Fix error check of of_io_request_and_map()

commit edf8fcdc6b254236be005851af35ea5e826e7e09 upstream.

The of_io_request_and_map() returns a valid pointer in iomem region or
ERR_PTR(), check for NULL always fails and may cause a NULL pointer
dereference on error path.

Fixes: 25e34b44313b ("irqchip/mxs: Prepare driver for hardware with different offsets")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1457486500-10237-1-git-send-email-vz@mleia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/sunxi-nmi: Fix error check of of_io_request_and_map()

commit cfe199afefe6201e998ddc07102fc1fdb55f196c upstream.

The of_io_request_and_map() returns a valid pointer in iomem region or
ERR_PTR(), check for NULL always fails and may cause a NULL pointer
dereference on error path.

Fixes: 0e841b04c829 ("irqchip/sunxi-nmi: Switch to of_io_request_and_map() from of_iomap()")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1457486489-10189-1-git-send-email-vz@mleia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi/rockchip: Make sure spi clk is on in rockchip_spi_set_cs

commit b920cc3191d7612f26f36ee494e05b5ffd9044c0 upstream.

Rockchip_spi_set_cs could be called by spi_setup, but
spi_setup may be called by device driver after runtime suspend.
Then the spi clock is closed, rockchip_spi_set_cs may access the
spi registers, which causes cpu block in some socs.

Fixes: 64e36824b32 ("spi/rockchip: add driver for Rockchip RK3xxx")
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking/mcs: Fix mcs_spin_lock() ordering

commit 920c720aa5aa3900a7f1689228fdfc2580a91e7e upstream.

Similar to commit b4b29f94856a ("locking/osq: Fix ordering of node
initialisation in osq_lock") the use of xchg_acquire() is
fundamentally broken with MCS like constructs.

Furthermore, it turns out we rely on the global transitivity of this
operation because the unlock path observes the pointer with a
READ_ONCE(), not an smp_load_acquire().

This is non-critical because the MCS code isn't actually used and
mostly serves as documentation, a stepping stone to the more complex
things we've build on top of the idea.

Reported-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: 3552a07a9c4a ("locking/mcs: Use acquire/release semantics")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: core: Fix nested locking of supplies

commit 70a7fb80e85ae7f78f8e90cec3fbd862ea6a4d4b upstream.

Commit fa731ac7ea04 ("regulator: core: avoid unused variable warning")
introduced a subtle change in how supplies are locked. Where previously
code was always locking the regulator of the current iteration, the new
implementation only locks the regulator if it has a supply. For any
given power tree that means that the root will never get locked.

On the other hand the regulator_unlock_supply() will still release all
the locks, which in turn causes the lock debugging code to warn about a
mutex being unlocked which wasn't locked.

Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: fa731ac7ea04 ("regulator: core: avoid unused variable warning")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: core: Ensure we lock all regulators

commit 49a6bb7a1c0963f260e4b0dcc2c0e56ec65a28b2 upstream.

The latest workaround for the lockdep interface's not using the second
argument of mutex_lock_nested() changed the loop missed locking the last
regulator due to a thinko with the loop termination condition exiting
one regulator too soon.

Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulator: core: fix regulator_lock_supply regression

commit bb41897e38c53458a88b271f2fbcd905ee1f9584 upstream.

As noticed by Geert Uytterhoeven, my patch to avoid a harmless build warning
in regulator_lock_supply() was total crap and introduced a real bug:

> [ BUG: bad unlock balance detected! ]
> kworker/u4:0/6 is trying to release lock (&rdev->mutex) at:
> [<c0247b84>] regulator_set_voltage+0x38/0x50

we still lock the regulator supplies, but not the actual regulators,
so we are missing a lock, and the unlock is unbalanced.

This rectifies it by first locking the regulator device itself before
using the same loop as before to lock its supplies.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 716fec9d1965 ("[SUBMITTED] regulator: core: avoid unused variable warning")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "regulator: core: Fix nested locking of supplies"

This reverts commit b1999fa6e8145305a6c8bda30ea20783717708e6 which was
commit 70a7fb80e85ae7f78f8e90cec3fbd862ea6a4d4b upstream.

It causes run-time breakage in the 4.4-stable tree and more patches are
needed to be applied first before this one in order to resolve the
issue.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

videobuf2-v4l2: Verify planes array in buffer dequeueing

commit 2c1f6951a8a82e6de0d82b1158b5e493fc6c54ab upstream.

When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer
which will be dequeued is not known until the buffer has been removed from
the queue. The number of planes is specific to a buffer, not to the queue.

This does lead to the situation where multi-plane buffers may be requested
and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument
struct with fewer planes.

__fill_v4l2_buffer() however uses the number of planes from the dequeued
videobuf2 buffer, overwriting kernel memory (the m.planes array allocated
in video_usercopy() in v4l2-ioctl.c) if the user provided fewer
planes than the dequeued buffer had. Oops!

Fixes: b0e0e1f83de3 ("[media] media: videobuf2: Prepare to divide videobuf2")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

videobuf2-core: Check user space planes array in dqbuf

commit e7e0c3e26587749b62d17b9dd0532874186c77f7 upstream.

The number of planes in videobuf2 is specific to a buffer. In order to
verify that the planes array provided by the user is long enough, a new
vb2_buf_op is required.

Call __verify_planes_array() when the dequeued buffer is known. Return an
error to the caller if there was one, otherwise remove the buffer from the
done list.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbip: fix potential out-of-bounds write

commit b348d7dddb6c4fbfc810b7a0626e8ec9e29f7cbb upstream.

Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.

Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup: make sure a parent css isn't freed before its children

commit 8bb5ef79bc0f4016ecf79e8dce6096a3c63603e4 upstream.

There are three subsystem callbacks in css shutdown path -
css_offline(), css_released() and css_free().  Except for
css_released(), cgroup core didn't guarantee the order of invocation.
css_offline() or css_free() could be called on a parent css before its
children.  This behavior is unexpected and led to bugs in cpu and
memory controller.

The previous patch updated ordering for css_offline() which fixes the
cpu controller issue.  While there currently isn't a known bug caused
by misordering of css_free() invocations, let's fix it too for
consistency.

css_free() ordering can be trivially fixed by moving putting of the
parent css below css_free() invocation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/hwpoison: fix wrong num_poisoned_pages accounting

commit d7e69488bd04de165667f6bc741c1c0ec6042ab9 upstream.

Currently, migration code increses num_poisoned_pages on *failed*
migration page as well as successfully migrated one at the trial of
memory-failure. It will make the stat wrong. As well, it marks the
page as PG_HWPoison even if the migration trial failed. It would mean
we cannot recover the corrupted page using memory-failure facility.

This patches fixes it.

Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: vmscan: reclaim highmem zone if buffer_heads is over limit

commit 7bf52fb891b64b8d61caf0b82060adb9db761aec upstream.

We have been reclaimed highmem zone if buffer_heads is over limit but
commit 6b4f7799c6a5 ("mm: vmscan: invoke slab shrinkers from
shrink_zone()") changed the behavior so it doesn't reclaim highmem zone
although buffer_heads is over the limit. This patch restores the logic.

Fixes: 6b4f7799c6a5 ("mm: vmscan: invoke slab shrinkers from shrink_zone()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

numa: fix /proc/<pid>/numa_maps for THP

commit 28093f9f34cedeaea0f481c58446d9dac6dd620f upstream.

In gather_pte_stats() a THP pmd is cast into a pte, which is wrong
because the layouts may differ depending on the architecture.  On s390
this will lead to inaccurate numa_maps accounting in /proc because of
misguided pte_present() and pte_dirty() checks on the fake pte.

On other architectures pte_present() and pte_dirty() may work by chance,
but there may be an issue with direct-access (dax) mappings w/o
underlying struct pages when HAVE_PTE_SPECIAL is set and THP is
available.  In vm_normal_page() the fake pte will be checked with
pte_special() and because there is no "special" bit in a pmd, this will
always return false and the VM_PFNMAP | VM_MIXEDMAP checking will be
skipped.  On dax mappings w/o struct pages, an invalid struct page
pointer would then be returned that can crash the kernel.

This patch fixes the numa_maps THP handling by introducing new "_pmd"
variants of the can_gather_numa_stats() and vm_normal_page() functions.

Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/huge_memory: replace VM_NO_THP VM_BUG_ON with actual VMA check

commit 3486b85a29c1741db99d0c522211c82d2b7a56d0 upstream.

Khugepaged detects own VMAs by checking vm_file and vm_ops but this way
it cannot distinguish private /dev/zero mappings from other special
mappings like /dev/hpet which has no vm_ops and popultes PTEs in mmap.

This fixes false-positive VM_BUG_ON and prevents installing THP where
they are not expected.

Link: http://lkml.kernel.org/r/CACT4Y+ZmuZMV5CjSFOeXviwQdABAgT7T+StKfTqan9YDtgEi5g@mail.gmail.com
Fixes: 78f11a255749 ("mm: thp: fix /dev/zero MAP_PRIVATE and vm_flags cleanups")
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memcg: relocate charge moving from ->attach to ->post_attach

commit 264a0ae164bc0e9144bebcd25ff030d067b1a878 upstream.

Hello,

So, this ended up a lot simpler than I originally expected.  I tested
it lightly and it seems to work fine.  Petr, can you please test these
two patches w/o the lru drain drop patch and see whether the problem
is gone?

Thanks.
------ 8< ------
If charge moving is used, memcg performs relabeling of the affected
pages from its ->attach callback which is called under both
cgroup_threadgroup_rwsem and thus can't create new kthreads.  This is
fragile as various operations may depend on workqueues making forward
progress which relies on the ability to create new kthreads.

There's no reason to perform charge moving from ->attach which is deep
in the task migration path.  Move it to ->post_attach which is called
after the actual migration is finished and cgroup_threadgroup_rwsem is
dropped.

* move_charge_struct->mm is added and ->can_attach is now responsible
  for pinning and recording the target mm.  mem_cgroup_clear_mc() is
  updated accordingly.  This also simplifies mem_cgroup_move_task().

* mem_cgroup_move_task() is now called from ->post_attach instead of
  ->attach.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Debugged-and-tested-by: Petr Mladek <pmladek@suse.com>
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Fixes: 1ed1328792ff ("sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup, cpuset: replace cpuset_post_attach_flush() with cgroup_subsys->post_attach callback

commit 5cf1cacb49aee39c3e02ae87068fc3c6430659b0 upstream.

Since e93ad19d0564 ("cpuset: make mm migration asynchronous"), cpuset
kicks off asynchronous NUMA node migration if necessary during task
migration and flushes it from cpuset_post_attach_flush() which is
called at the end of __cgroup_procs_write().  This is to avoid
performing migration with cgroup_threadgroup_rwsem write-locked which
can lead to deadlock through dependency on kworker creation.

memcg has a similar issue with charge moving, so let's convert it to
an official callback rather than the current one-off cpuset specific
function.  This patch adds cgroup_subsys->post_attach callback and
makes cpuset register cpuset_post_attach_flush() as its ->post_attach.

The conversion is mostly one-to-one except that the new callback is
called under cgroup_mutex.  This is to guarantee that no other
migration operations are started before ->post_attach callbacks are
finished.  cgroup_mutex is one of the outermost mutex in the system
and has never been and shouldn't be a problem.  We can add specialized
synchronization around __cgroup_procs_write() but I don't think
there's any noticeable benefit.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

slub: clean up code for kmem cgroup support to kmem_cache_free_bulk

commit 376bf125ac781d32e202760ed7deb1ae4ed35d31 upstream.

This change is primarily an attempt to make it easier to realize the
optimizations the compiler performs in-case CONFIG_MEMCG_KMEM is not
enabled.

Performance wise, even when CONFIG_MEMCG_KMEM is compiled in, the
overhead is zero.  This is because, as long as no process have enabled
kmem cgroups accounting, the assignment is replaced by asm-NOP
operations.  This is possible because memcg_kmem_enabled() uses a
static_key_false() construct.

It also helps readability as it avoid accessing the p[] array like:
p[size - 1] which "expose" that the array is processed backwards inside
helper function build_detached_freelist().

Lastly this also makes the code more robust, in error case like passing
NULL pointers in the array.  Which were previously handled before commit
033745189b1b ("slub: add missing kmem cgroup support to
kmem_cache_free_bulk").

Fixes: 033745189b1b ("slub: add missing kmem cgroup support to kmem_cache_free_bulk")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

workqueue: fix ghost PENDING flag while doing MQ IO

commit 346c09f80459a3ad97df1816d6d606169a51001a upstream.

The bug in a workqueue leads to a stalled IO request in MQ ctx->rq_list
with the following backtrace:

[  601.347452] INFO: task kworker/u129:5:1636 blocked for more than 120 seconds.
[  601.347574]       Tainted: G           O    4.4.5-1-storage+ #6
[  601.347651] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  601.348142] kworker/u129:5  D ffff880803077988     0  1636      2 0x00000000
[  601.348519] Workqueue: ibnbd_server_fileio_wq ibnbd_dev_file_submit_io_worker [ibnbd_server]
[  601.348999]  ffff880803077988 ffff88080466b900 ffff8808033f9c80 ffff880803078000
[  601.349662]  ffff880807c95000 7fffffffffffffff ffffffff815b0920 ffff880803077ad0
[  601.350333]  ffff8808030779a0 ffffffff815b01d5 0000000000000000 ffff880803077a38
[  601.350965] Call Trace:
[  601.351203]  [<ffffffff815b0920>] ? bit_wait+0x60/0x60
[  601.351444]  [<ffffffff815b01d5>] schedule+0x35/0x80
[  601.351709]  [<ffffffff815b2dd2>] schedule_timeout+0x192/0x230
[  601.351958]  [<ffffffff812d43f7>] ? blk_flush_plug_list+0xc7/0x220
[  601.352208]  [<ffffffff810bd737>] ? ktime_get+0x37/0xa0
[  601.352446]  [<ffffffff815b0920>] ? bit_wait+0x60/0x60
[  601.352688]  [<ffffffff815af784>] io_schedule_timeout+0xa4/0x110
[  601.352951]  [<ffffffff815b3a4e>] ? _raw_spin_unlock_irqrestore+0xe/0x10
[  601.353196]  [<ffffffff815b093b>] bit_wait_io+0x1b/0x70
[  601.353440]  [<ffffffff815b056d>] __wait_on_bit+0x5d/0x90
[  601.353689]  [<ffffffff81127bd0>] wait_on_page_bit+0xc0/0xd0
[  601.353958]  [<ffffffff81096db0>] ? autoremove_wake_function+0x40/0x40
[  601.354200]  [<ffffffff81127cc4>] __filemap_fdatawait_range+0xe4/0x140
[  601.354441]  [<ffffffff81127d34>] filemap_fdatawait_range+0x14/0x30
[  601.354688]  [<ffffffff81129a9f>] filemap_write_and_wait_range+0x3f/0x70
[  601.354932]  [<ffffffff811ced3b>] blkdev_fsync+0x1b/0x50
[  601.355193]  [<ffffffff811c82d9>] vfs_fsync_range+0x49/0xa0
[  601.355432]  [<ffffffff811cf45a>] blkdev_write_iter+0xca/0x100
[  601.355679]  [<ffffffff81197b1a>] __vfs_write+0xaa/0xe0
[  601.355925]  [<ffffffff81198379>] vfs_write+0xa9/0x1a0
[  601.356164]  [<ffffffff811c59d8>] kernel_write+0x38/0x50

The underlying device is a null_blk, with default parameters:

  queue_mode    = MQ
  submit_queues = 1

Verification that nullb0 has something inflight:

root@pserver8:~# cat /sys/block/nullb0/inflight
       0        1
root@pserver8:~# find /sys/block/nullb0/mq/0/cpu* -name rq_list -print -exec cat {} \;
...
/sys/block/nullb0/mq/0/cpu2/rq_list
CTX pending:
        ffff8838038e2400
...

During debug it became clear that stalled request is always inserted in
the rq_list from the following path:

   save_stack_trace_tsk + 34
   blk_mq_insert_requests + 231
   blk_mq_flush_plug_list + 281
   blk_flush_plug_list + 199
   wait_on_page_bit + 192
   __filemap_fdatawait_range + 228
   filemap_fdatawait_range + 20
   filemap_write_and_wait_range + 63
   blkdev_fsync + 27
   vfs_fsync_range + 73
   blkdev_write_iter + 202
   __vfs_write + 170
   vfs_write + 169
   kernel_write + 56

So blk_flush_plug_list() was called with from_schedule == true.

If from_schedule is true, that means that finally blk_mq_insert_requests()
offloads execution of __blk_mq_run_hw_queue() and uses kblockd workqueue,
i.e. it calls kblockd_schedule_delayed_work_on().

That means, that we race with another CPU, which is about to execute
__blk_mq_run_hw_queue() work.

Further debugging shows the following traces from different CPUs:

  CPU#0                                  CPU#1
  ----------------------------------     -------------------------------
  reqeust A inserted
  STORE hctx->ctx_map[0] bit marked
  kblockd_schedule...() returns 1
  <schedule to kblockd workqueue>
                                         request B inserted
                                         STORE hctx->ctx_map[1] bit marked
                                         kblockd_schedule...() returns 0
  *** WORK PENDING bit is cleared ***
  flush_busy_ctxs() is executed, but
  bit 1, set by CPU#1, is not observed

As a result request B pended forever.

This behaviour can be explained by speculative LOAD of hctx->ctx_map on
CPU#0, which is reordered with clear of PENDING bit and executed _before_
actual STORE of bit 1 on CPU#1.

The proper fix is an explicit full barrier <mfence>, which guarantees
that clear of PENDING bit is to be executed before all possible
speculative LOADS or STORES inside actual work function.

Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Michael Wang <yun.wang@profitbricks.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/apic: Handle zero vector gracefully in clear_vector_irq()

commit 1bdb8970392a68489b469c3a330a1adb5ef61beb upstream.

If x86_vector_alloc_irq() fails x86_vector_free_irqs() is invoked to cleanup
the already allocated vectors. This subsequently calls clear_vector_irq().

The failed irq has no vector assigned, which triggers the BUG_ON(!vector) in
clear_vector_irq().

We cannot suppress the call to x86_vector_free_irqs() for the failed
interrupt, because the other data related to this irq must be cleaned up as
well. So calling clear_vector_irq() with vector == 0 is legitimate.

Remove the BUG_ON and return if vector is zero,

[ tglx: Massaged changelog ]

Fixes: b5dc8e6c21e7 "x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors"
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Expose non-blocking set_variable() wrapper to efivars

commit 9c6672ac9c91f7eb1ec436be1442b8c26d098e55 upstream.

Commit 6d80dba1c9fe ("efi: Provide a non-blocking SetVariable()
operation") implemented a non-blocking alternative for the UEFI
SetVariable() invocation performed by efivars, since it may
occur in atomic context. However, this version of the function
was never exposed via the efivars struct, so the non-blocking
versions was not actually callable. Fix that.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 6d80dba1c9fe ("efi: Provide a non-blocking SetVariable() operation")
Link: http://lkml.kernel.org/r/1454364428-494-2-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: Fix out-of-bounds read in variable_matches()

commit 630ba0cc7a6dbafbdee43795617c872b35cde1b4 upstream.

The variable_matches() function can currently read "var_name[len]", for
example when:

- var_name[0] == 'a',
- len == 1
- match_name points to the NUL-terminated string "ab".

This function is supposed to accept "var_name" inputs that are not
NUL-terminated (hence the "len" parameter"). Document the function, and
access "var_name[*match]" only if "*match" is smaller than "len".

Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@coreos.com>
Cc: Jason Andryuk <jandryuk@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://thread.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/86906
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/security: Restrict use of the write() interface

commit e6bd18f57aad1a2d1ef40e646d03ed0f2515c9e3 upstream.

The drivers/infiniband stack uses write() as a replacement for
bi-directional ioctl(). This is not safe. There are ways to
trigger write calls that result in the return structure that
is normally written to user space being shunted off to user
specified kernel memory instead.

For the immediate repair, detect and deny suspicious accesses to
the write API.

For long term, update the user space libraries and the kernel API
to something that doesn't present the same security vulnerabilities
(likely a structured ioctl() interface).

The impacted uAPI interfaces are generally only available if
hardware from drivers/infiniband is installed in the system.

Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ Expanded check to all known write() entry points ]
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Expose correct max_sge_rd limit

commit 986ef95ecdd3eb6fa29433e68faa94c7624083be upstream.

mlx5 devices (Connect-IB, ConnectX-4, ConnectX-4-LX) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)

So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.

Reported-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagig@grimberg.me>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxl: Keep IRQ mappings on context teardown

commit d6776bba44d9752f6cdf640046070e71ee4bba7b upstream.

Keep IRQ mappings on context teardown. This won't leak IRQs as if we
allocate the mapping again, the generic code will give the same
mapping used last time.

Doing this works around a race in the generic code. Masking the
interrupt introduces a race which can crash the kernel or result in
IRQ that is never EOIed. The lost of EOI results in all subsequent
mappings to the same HW IRQ never receiving an interrupt.

We've seen this race with cxl test cases which are doing heavy context
startup and teardown at the same time as heavy interrupt load.

A fix to the generic code is being investigated also.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Tested-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

v4l2-dv-timings.h: fix polarity for 4k formats

commit 3020ca711871fdaf0c15c8bab677a6bc302e28fe upstream.

The VSync polarity was negative instead of positive for the 4k CEA formats.
I probably copy-and-pasted these from the DMT 4k format, which does have a
negative VSync polarity.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vb2-memops: Fix over allocation of frame vectors

commit 89a095668304e8a02502ffd35edacffdbf49aa8c upstream.

On page unaligned frames, create_framevec forces get_vaddr_frames to
allocate an extra page at the end of the buffer. Under some
circumstances, this leads to -EINVAL on VIDIOC_QBUF.

E.g:
We have vm_a that vm_area that goes from 0x1000 to 0x3000. And a
frame that goes from 0x1800 to 0x2800, i.e. 2 pages.

frame_vector_create will be called with the following params:

get_vaddr_frames(0x1800, 2, write, 1, vec);

get_vaddr will allocate the first page after checking that the memory
0x1800-0x27ff is valid, but it will not allocate the second page because
the range 0x2800-0x37ff is out of the vm_a range. This results in
create_framevec returning -EFAULT

Error Trace:
[ 9083.793015] video0: VIDIOC_QBUF: 00:00:00.00000000 index=1,
type=vid-cap, flags=0x00002002, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b023ca80, length=5765760
[ 9083.793028] timecode=00:00:00 type=0, flags=0x00000000,
frames=0, userbits=0x00000000
[ 9083.793117] video0: VIDIOC_QBUF: error -22: 00:00:00.00000000
index=2, type=vid-cap, flags=0x00000000, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b07bc500, length=5765760

Also use true instead of 1 since that argument is a bool in the
get_vaddr_frames() prototype.

Fixes: 21fb0cb7ec65 ("[media] vb2: Provide helpers for mapping virtual addresses")
Reported-by: Albert Antony <albert@newtec.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[hans.verkuil@cisco.com: merged the 'bool' change into this patch]
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

ASoC: rt5640: Correct the digital interface data select

commit 653aa4645244042826f105aab1be3d01b3d493ca upstream.

this patch corrects the interface adc/dac control register definition
according to datasheet.

Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: dapm: Make sure we have a card when displaying component widgets

commit 47325078f2a3e543150e7df967e45756b2fff7ec upstream.

The dummy component is reused for all cards so we special case and don't
bind it to any of them. This means that code like that displaying the
component widgets that tries to look at the card will crash. In the
future we will fix this by ensuring that the dummy component looks like
other components but that is invasive and so not suitable for a fix.
Instead add a special case check here.

Reported-by: Harry Pan <harry.pan@intel.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ssm4567: Reset device before regcache_sync()

commit 712a8038cc24dba668afe82f0413714ca87184e0 upstream.

When the ssm4567 is powered up the driver calles regcache_sync() to restore
the register map content. regcache_sync() assumes that the device is in its
power-on reset state. Make sure that this is the case by explicitly
resetting the ssm4567 register map before calling regcache_sync() otherwise
we might end up with a incorrect register map which leads to undefined
behaviour.

One such undefined behaviour was observed when returning from system
suspend while a playback stream is active, in that case the ssm4567 was
kept muted after resume.

Fixes: 1ee44ce03011 ("ASoC: ssm4567: Add driver for Analog Devices SSM4567 amplifier")
Reported-by: Harsha Priya <harshapriya.n@intel.com>
Tested-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: s3c24xx: use const snd_soc_component_driver pointer

commit ba4bc32eaa39ba7687f0958ae90eec94da613b46 upstream.

An older patch to convert the API in the s3c i2s driver
ended up passing a const pointer into a function that takes
a non-const pointer, so we now get a warning:

sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe':
sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]

However, the s3c_i2sv2_register_component() function again
passes the pointer into another function taking a const, so
we just need to change its prototype.

Fixes: eca3b01d0885 ("ASoC: switch over to use snd_soc_register_component() on s3c i2s")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EDAC: i7core, sb_edac: Don't return NOTIFY_BAD from mce_decoder callback

commit c4fc1956fa31003bfbe4f597e359d751568e2954 upstream.

Both of these drivers can return NOTIFY_BAD, but this terminates
processing other callbacks that were registered later on the chain.
Since the driver did nothing to log the error it seems wrong to prevent
other interested parties from seeing it. E.g. neither of them had even
bothered to check the type of the error to see if it was a memory error
before the return NOTIFY_BAD.

Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/72937355dd92318d2630979666063f8a2853495b.1461864507.git.tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

toshiba_acpi: Fix regression caused by hotkey enabling value

commit a30b8f81d9d6fe24eab8a023794548b048f08e3c upstream.

Commit 52cbae0127ad ("toshiba_acpi: Change default Hotkey enabling value")
changed the hotkeys enabling value, as it was the same value Windows uses,
however, it turns out that the value tells the EC that the driver will now
take care of the hardware events like the physical RFKill switch or the
pointing device toggle button.

This patch reverts such commit by changing the default hotkey enabling
value to 0x09, which enables hotkey events only, making the hardware
buttons working again.

Fixes bugs 113331 and 114941.

Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: exynos5: Fix possible ABBA deadlock by keeping I2C clock prepared

commit 10ff4c5239a137abfc896ec73ef3d15a0f86a16a upstream.

The exynos5 I2C controller driver always prepares and enables a clock
before using it and then disables unprepares it when the clock is not
used anymore.

But this can cause a possible ABBA deadlock in some scenarios since a
driver that uses regmap to access its I2C registers, will first grab
the regmap lock and then the I2C xfer function will grab the prepare
lock when preparing the I2C clock. But since the clock driver also
uses regmap for I2C accesses, preparing a clock will first grab the
prepare lock and then the regmap lock when using the regmap API.

An example of this happens on the Exynos5422 Odroid XU4 board where a
s2mps11 PMIC is used and both the s2mps11 regulators and clk drivers
share the same I2C regmap.

The possible deadlock is reported by the kernel lockdep:

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(sec_core:428:(regmap)->lock);
                                lock(prepare_lock);
                                lock(sec_core:428:(regmap)->lock);
   lock(prepare_lock);

  *** DEADLOCK ***

Fix it by leaving the code prepared on probe and use {en,dis}able in
the I2C transfer function.

This patch is similar to commit 34e81ad5f0b6 ("i2c: s3c2410: fix ABBA
deadlock by keeping clock prepared") that fixes the same bug in other
driver for an I2C controller found in Samsung SoCs.

Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: cpm: Fix build break due to incompatible pointer types

commit 609d5a1b2b35bb62b4b3750396e55453160c2a17 upstream.

Since commit ea8daa7b9784 ("kbuild: Add option to turn incompatible
pointer check into error"), assignments from an incompatible pointer
types have become a hard error, eg:

drivers/i2c/busses/i2c-cpm.c:545:91: error: passing argument 3 of
'dma_alloc_coherent' from incompatible pointer type

Fix the build break by converting txdma & rxdma to dma_addr_t.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: ea8daa7b9784
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf intel-pt: Fix segfault tracing transactions

commit 1342e0b7a6c1a060c593037fbac9f4b717f1cb3b upstream.

Tracing a workload that uses transactions gave a seg fault as follows:

  perf record -e intel_pt// workload
  perf report
  Program received signal SIGSEGV, Segmentation fault.
  0x000000000054b58c in intel_pt_reset_last_branch_rb (ptq=0x1a36110)
   at util/intel-pt.c:929
  929 ptq->last_branch_rb->nr = 0;
  (gdb) p ptq->last_branch_rb
  $1 = (struct branch_stack *) 0x0
  (gdb) up
  1148 intel_pt_reset_last_branch_rb(ptq);
  (gdb) l
  1143 if (ret)
  1144 pr_err("Intel Processor Trace: failed to deliver transaction event
  1145 ret);
  1146
  1147 if (pt->synth_opts.callchain)
  1148 intel_pt_reset_last_branch_rb(ptq);
  1149
  1150 return ret;
  1151 }
  1152
  (gdb) p pt->synth_opts.callchain
  $2 = true
  (gdb)
  (gdb) bt
   #0 0x000000000054b58c in intel_pt_reset_last_branch_rb (ptq=0x1a36110)
   #1 0x000000000054c1e0 in intel_pt_synth_transaction_sample (ptq=0x1a36110)
   #2 0x000000000054c5b2 in intel_pt_sample (ptq=0x1a36110)

Caused by checking the 'callchain' flag when it should have been the
'last_branch' flag.  Fix that.

Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: f14445ee72c5 ("perf intel-pt: Support generating branch stack")
Link: http://lkml.kernel.org/r/1460977068-11566-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Use fw_domains_put_with_fifo() on HSW

commit 31318a922395ec9e78d6e2ddf70779355afc7594 upstream.

HSW still has the wake FIFO, so let's check it.

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Fixes: 05a2fb157e44 ("drm/i915: Consolidate forcewake code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460633942-24013-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 3d7d0c85e41afb5a05e98b3a8a72c38357f02594)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Fixup the free space logic in ring_prepare

commit d43f3ebf12f59c57782ec652da65ef61c2662b40 upstream.

Currently for the case where there is enough space at the end of Ring
buffer for accommodating only the base request, the wrapround is done
immediately and as a result the base request gets added at the start
of Ring buffer. But there may not be enough free space at the beginning
to accommodate the base request, as before the wraparound, the wait was
effectively done for the reserved_size free space from the start of
Ring buffer. In such a case there is a potential of Ring buffer overflow,
the instructions at the head of Ring (ACTHD) can get overwritten.

Since the base request can fit in the remaining space, there is no need
to wraparound immediately. The wraparound will anyway happen later when
the reserved part starts getting used.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1457688402-10411-1-git-send-email-akash.goel@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 782f6bc0aba037436d6a04d19b23f8b61020a576)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdkfd: uninitialized variable in dbgdev_wave_control_set_registers()

commit 93fce954427effee89e44a976299b15dd75b4bbc upstream.

At the end of the function we expect "status" to be zero, but it's
either -EINVAL or uninitialized.

Fixes: 788bf83db301 ('drm/amdkfd: Add wave control operation to debugger')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: skl_update_scaler() wants a rotation bitmask instead of bit number

commit fa5a7970d372c9c9beb3a0ce79ee1d0c23387d0a upstream.

Pass BIT(DRM_ROTATE_0) instead of DRM_ROTATE_0 to skl_update_scaler().
The former is a mask, the latter just the bit number.

Fortunately the only thing skl_update_scaler() does with the rotation
is check if it's 90/270 degrees or not, and so in this case it would
still do the right thing.

Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1444917718-28495-1-git-send-email-ville.syrjala@linux.intel.com
Fixes: 6156a45602f9 ("drm/i915: skylake primary plane scaling using shared scalers")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Cleanup phys status page too

commit 7d3fdfff23852fe458a0d0979a3555fe60f1e563 upstream.

Restore the lost phys status page cleanup.

Fixes the following splat with DMA_API_DEBUG=y:

WARNING: CPU: 0 PID: 21615 at ../lib/dma-debug.c:974 dma_debug_device_change+0x190/0x1f0()
pci 0000:00:02.0: DMA-API: device driver has pending DMA allocations while released from device [count=1]
               One of leaked entries details: [device address=0x0000000023163000] [size=4096 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent]
Modules linked in: i915(-) i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm sha256_generic hmac drbg ctr ccm sch_fq_codel binfmt_misc joydev mousedev arc4 ath5k iTCO_wdt mac80211 smsc_ircc2 ath snd_intel8x0m snd_intel8x0 snd_ac97_codec ac97_bus psmouse snd_pcm input_leds i2c_i801 pcspkr snd_timer cfg80211 snd soundcore i2c_core ehci_pci firewire_ohci ehci_hcd firewire_core lpc_ich 8139too rfkill crc_itu_t mfd_core mii usbcore rng_core intel_agp intel_gtt usb_common agpgart irda crc_ccitt fujitsu_laptop led_class parport_pc video parport evdev backlight
CPU: 0 PID: 21615 Comm: rmmod Tainted: G     U          4.4.0-rc4-mgm-ovl+ #4
Hardware name: FUJITSU SIEMENS LIFEBOOK S6120/FJNB16C, BIOS Version 1.26  05/10/2004
e31a3de0 e31a3de0 e31a3d9c c128d4bd e31a3dd0 c1045a0c c15e00c4 e31a3dfc
0000546f c15dfad2 000003ce c12b3740 000003ce c12b3740 00000000 00000001
f61fb8a0 e31a3de8 c1045a83 00000009 e31a3de0 c15e00c4 e31a3dfc e31a3e4c
Call Trace:
[<c128d4bd>] dump_stack+0x16/0x19
[<c1045a0c>] warn_slowpath_common+0x8c/0xd0
[<c12b3740>] ? dma_debug_device_change+0x190/0x1f0
[<c12b3740>] ? dma_debug_device_change+0x190/0x1f0
[<c1045a83>] warn_slowpath_fmt+0x33/0x40
[<c12b3740>] dma_debug_device_change+0x190/0x1f0
[<c1065499>] notifier_call_chain+0x59/0x70
[<c10655af>] __blocking_notifier_call_chain+0x3f/0x80
[<c106560f>] blocking_notifier_call_chain+0x1f/0x30
[<c134cfb3>] __device_release_driver+0xc3/0xf0
[<c134d0d7>] driver_detach+0x97/0xa0
[<c134c440>] bus_remove_driver+0x40/0x90
[<c134db18>] driver_unregister+0x28/0x60
[<c1079e8c>] ? trace_hardirqs_on_caller+0x12c/0x1d0
[<c12c0618>] pci_unregister_driver+0x18/0x80
[<f83e96e7>] drm_pci_exit+0x87/0xb0 [drm]
[<f8b3be2d>] i915_exit+0x1b/0x1ee [i915]
[<c10b999c>] SyS_delete_module+0x14c/0x210
[<c1079e8c>] ? trace_hardirqs_on_caller+0x12c/0x1d0
[<c115a9bd>] ? ____fput+0xd/0x10
[<c1002014>] do_fast_syscall_32+0xa4/0x450
[<c149f6fa>] sysenter_past_esp+0x3b/0x5d
---[ end trace c2ecbc77760f10a0 ]---
Mapped at:
[<c12b3183>] debug_dma_alloc_coherent+0x33/0x90
[<f83e989c>] drm_pci_alloc+0x18c/0x1e0 [drm]
[<f8acd59f>] intel_init_ring_buffer+0x2af/0x490 [i915]
[<f8acd8b0>] intel_init_render_ring_buffer+0x130/0x750 [i915]
[<f8aaea4e>] i915_gem_init_rings+0x1e/0x110 [i915]

v2: s/BUG_ON/WARN_ON/ since dim doens't like the former anymore

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 5c6c600 ("drm/i915: Remove DRI1 ring accessors and API")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1452538112-5331-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pwm: brcmstb: Fix check of devm_ioremap_resource() return code

commit c5857e3f94ab2719dfac649a146cb5dd6f21fcf3 upstream.

The change fixes potential oops while accessing iomem on invalid address
if devm_ioremap_resource() fails due to some reason.

The devm_ioremap_resource() function returns ERR_PTR() and never returns
NULL, which makes useless a following check for NULL.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fixes: 3a9f5957020f ("pwm: Add Broadcom BCM7038 PWM controller support")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/dp/mst: Get validated port ref in drm_dp_update_payload_part1()

commit 263efde31f97c498e1ebad30e4d2906609d7ad6b upstream.

We can thank KASAN for finding this, otherwise I probably would have spent
hours on it. This fixes a somewhat harder to trigger kernel panic, occuring
while enabling MST where the port we were currently updating the payload on
would have all of it's refs dropped before we finished what we were doing:

==================================================================
BUG: KASAN: use-after-free in drm_dp_update_payload_part1+0xb3f/0xdb0 [drm_kms_helper] at addr ffff8800d29de018
Read of size 4 by task Xorg/973
=============================================================================
BUG kmalloc-2048 (Tainted: G B W ): kasan: bad access detected
-----------------------------------------------------------------------------

INFO: Allocated in drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper] age=16477 cpu=0 pid=2175
___slab_alloc+0x472/0x490
__slab_alloc+0x20/0x40
kmem_cache_alloc_trace+0x151/0x190
drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper]
drm_dp_send_link_address+0x526/0x960 [drm_kms_helper]
drm_dp_check_and_send_link_address+0x1ac/0x210 [drm_kms_helper]
drm_dp_mst_link_probe_work+0x77/0xd0 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
INFO: Freed in drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper] age=7521 cpu=0 pid=2175
__slab_free+0x17f/0x2d0
kfree+0x169/0x180
drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper]
drm_dp_destroy_connector_work+0x2b8/0x490 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40

which on this T460s, would eventually lead to kernel panics in somewhat
random places later in intel_mst_enable_dp() if we got lucky enough.

Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/dp/mst: Restore primary hub guid on resume

commit 9dc0487d96a0396367a1451b31873482080b527f upstream.

Some hubs are forgetful, and end up forgetting whatever GUID we set
previously after we do a suspend/resume cycle. This can lead to
hotplugging breaking (along with probably other things) since the hub
will start sending connection notifications with the wrong GUID. As
such, we need to check on resume whether or not the GUID the hub is
giving us is valid.

Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460580618-7421-1-git-send-email-cpaul@redhat.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/dp/mst: Validate port in drm_dp_payload_send_msg()

commit deba0a2af9592b2022a0bce7b085a318b53ce1db upstream.

With the joys of things running concurrently, there's always a chance
that the port we get passed in drm_dp_payload_send_msg() isn't actually
valid anymore. Because of this, we need to make sure we validate the
reference to the port before we use it otherwise we risk running into
various race conditions. For instance, on the Dell MST monitor I have
here for testing, hotplugging it enough times causes us to kernel panic:

[drm:intel_mst_enable_dp] 1
[drm:drm_dp_update_payload_part2] payload 0 1
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020
[drm:intel_hpd_irq_handler] digital hpd port B - short
[drm:intel_dp_hpd_pulse] got hpd irq on port B - short
[drm:intel_dp_check_mst_status] got esi 00 10 00
[drm:drm_dp_update_payload_part2] payload 1 1
general protection fault: 0000 [#1] SMP
…
Call Trace:
[<ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper]
[<ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915]
[<ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915]
[<ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915]
[<ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm]
[<ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm]
[<ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper]
[<ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm]
[<ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm]
[<ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm]
[<ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm]
[<ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0
[<ffffffff81212962>] do_vfs_ioctl+0x92/0x570
[<ffffffff81590852>] ? __sys_recvmsg+0x42/0x80
[<ffffffff81212eb9>] SyS_ioctl+0x79/0x90
[<ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
RIP [<ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper]

Which occurs because of the hotplug event shown in the log, which ends
up causing DRM's dp helpers to drop the port we're updating the payload
on and panic.

Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries

commit 28dca90533750c7e31e8641c3df426bad9c12941 upstream.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: Loongson-3 doesn't fully support wc memory

commit 221004c66a58949a0f25c937a6789c0839feb530 upstream.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: fix vertical bars appear on monitor (v2)

commit 5d5b7803c49bbb01bdf4c6e95e8314d0515b9484 upstream.

When crtc/timing is disabled on boot the dig block
should be stopped in order ignore timing from crtc,
reset the steering fifo otherwise we get display
corruption or hung in dp sst mode.

v2: agd: fix coding style

Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: forbid mapping of userptr bo through radeon device file

commit b5dcec693f87cb8475f2291c0075b2422addd3d6 upstream.

Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).

This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.

So to be safe just add a check to verify_access() callback.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: fix initial connector audio value

commit 7403c515c49c033fec33df0814fffdc977e6acdc upstream.

This got lost somewhere along the way. This fixes
audio not working until set_property was called.

Noticed-by: Hyungwon Hwang <hyungwon.hwang7@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: add a quirk for a XFX R9 270X

commit bcb31eba4a4ea356fd61cbd5dec5511c3883f57e upstream.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76490

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: fix regression on CIK (v2)

This fix was written against drm-next, but when it was
backported to 4.5 as a stable fix, the driver internal
structure change was missed. Fix that up here to avoid
a hang due to waiting for the wrong sequence number.

v2: agd: fix up commit message

Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amdgpu/uvd: add uvd fw version for amdgpu

commit 562e2689baebaa2ac25b7ec934385480ed1cb7d6 upstream.

Was previously always hardcoded to 0.

Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: bump the afmt limit for CZ, ST, Polaris

commit 83c5cda2ccf40a7a7e4bb674321509b346e23d5a upstream.

Fixes array overflow on these chips.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: use defines for CRTCs and AMFT blocks

commit 3ea25f858fd5aeee888059952bbb8e910541eebb upstream.

Prerequiste for the next patch which ups the limits.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: when suspending, if uvd/vce was running. need to cancel delay work.

commit 85cc88f02eb0ecf44493c1b2ebb6f206cd5fc321 upstream.

fix the issue that when resume back, uvd/vce
dpm was disabled and uvd/vce's performace
dropped.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/dma: Restore scatterlist offsets correctly

commit 07b48ac4bbe527e68cfc555f2b2b206908437141 upstream.

With the change to stashing just the IOVA-page-aligned remainder of the
CPU-page offset rather than the whole thing, the failure path in
__invalidate_sg() also needs tweaking to account for that in the case of
differing page sizes where the two offsets may not be equivalent.
Similarly in __finalise_sg(), lest the architecture-specific wrappers
later get the wrong address for cache maintenance on sync or unmap.

Fixes: 164afb1d85b8 ("iommu/dma: Use correct offset in map_sg")
Reported-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/amd: Fix checking of pci dma aliases

commit e3156048346c28c695f5cf9db67a8cf88c90f947 upstream.

Commit 61289cb ('iommu/amd: Remove old alias handling code')
removed the old alias handling code from the AMD IOMMU
driver because this is now handled by the IOMMU core code.

But this also removed the handling of PCI aliases, which is
not handled by the core code. This caused issues with PCI
devices that have hidden PCIe-to-PCI bridges that rewrite
the request-id.

Fix this bug by re-introducing some of the removed functions
from commit 61289cbaf6c8 and add a alias field
'struct iommu_dev_data'. This field carrys the return value
of the get_alias() function and uses that instead of the
amd_iommu_alias_table[] array in the code.

Fixes: 61289cbaf6c8 ('iommu/amd: Remove old alias handling code')
Tested-by: Tomasz Golinski <tomaszg@math.uwb.edu.pl>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: single: Fix pcs_parse_bits_in_pinctrl_entry to use __ffs than ffs

commit 56b367c0cd67d4c3006738e7dc9dda9273fd2bfe upstream.

pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices
ranging from 1 to MAX. This leads to a corner case where we try to request
the pin number = MAX and fails.

bit_pos value is being calculted using ffs. pin_num_from_lsb uses
bit_pos value. pins array is populated with:

pin + pin_num_from_lsb.

The above is 1 more than usual bit indices as bit_pos uses ffs to compute
first set bit. Hence the last of the pins array is populated with the MAX
value and not MAX - 1 which causes error when we call pin_request.

mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1))
Consequently val_pos and submask are correct.

Hence use __ffs which gives (ffs(x) - 1) as the first bit set.

fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: mediatek: correct debounce time unit in mtk_gpio_set_debounce

commit 5fedbb923936174ab4d1d5cc92bca1cf6b2e0ca2 upstream.

The debounce time unit for gpio_chip.set_debounce is us but
mtk_gpio_set_debounce regard it as ms.
Fix this by correct debounce time array dbnc_arr so it can find correct
debounce setting. Debounce time for first debounce setting is 500us,
correct this as well.

While I'm at it, also change the debounce time array name to
"debounce_time" for readability.

Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen kconfig: don't "select INPUT_XEN_KBDDEV_FRONTEND"

commit 13aa38e291bdd4e4018f40dd2f75e464814dcbf3 upstream.

The Xen framebuffer driver selects the xen keyboard driver, so the latter
will be built-in if XEN_FBDEV_FRONTEND=y. However, when CONFIG_INPUT
is a loadable module, this configuration cannot work. On mainline kernels,
the symbol will be enabled but not used, while in combination with
a patch I have to detect such useless configurations, we get the
expected link failure:

drivers/input/built-in.o: In function `xenkbd_remove':
xen-kbdfront.c:(.text+0x2f0): undefined reference to `input_unregister_device'
xen-kbdfront.c:(.text+0x30e): undefined reference to `input_unregister_device'

This removes the extra "select", as it just causes more trouble than
it helps. In theory, some defconfig file might break if it has
XEN_FBDEV_FRONTEND in it but not INPUT_XEN_KBDDEV_FRONTEND. The Kconfig
fragment we ship in the kernel (kernel/configs/xen.config) however
already enables both, and anyone using an old .config file would
keep having both enabled.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Fixes: 36c1132e34bd ("xen kconfig: fix select INPUT_XEN_KBDDEV_FRONTEND")
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: pmic8xxx-pwrkey - fix algorithm for converting trigger delay

commit eda5ecc0a6b865561997e177c393f0b0136fe3b7 upstream.

The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is

delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)

except for one case where the documentation looks to have a
formatting issue and the equation looks like

delay (Seconds) = (1 / 1024) * 2 x + 4

Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.

Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e410 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: gtco - fix crash on detecting device without endpoints

commit 162f98dea487206d9ab79fc12ed64700667a894d upstream.

The gtco driver expects at least one valid endpoint. If given malicious
descriptors that specify 0 for the number of endpoints, it will crash in
the probe function. Ensure there is at least one endpoint on the interface
before using it.

Also let's fix a minor coding style issue.

The full correct report of this issue can be found in the public
Red Hat Bugzilla:

https://bugzilla.redhat.com/show_bug.cgi?id=1283385

Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netlink: don't send NETLINK_URELEASE for unbound sockets

commit e27260203912b40751fa353d009eaa5a642c739f upstream.

All existing users of NETLINK_URELEASE use it to clean up resources that
were previously allocated to a socket via some command. As a result, no
users require getting this notification for unbound sockets.

Sending it for unbound sockets, however, is a problem because any user
(including unprivileged users) can create a socket that uses the same ID
as an existing socket. Binding this new socket will fail, but if the
NETLINK_URELEASE notification is generated for such sockets, the users
thereof will be tricked into thinking the socket that they allocated the
resources for is closed.

In the nl80211 case, this will cause destruction of virtual interfaces
that still belong to an existing hostapd process; this is the case that
Dmitry noticed. In the NFC case, it will cause a poll abort. In the case
of netlink log/queue it will cause them to stop reporting events, as if
NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called.

Fix this problem by checking that the socket is bound before generating
the NETLINK_URELEASE notification.

Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nl80211: check netlink protocol in socket release notification

commit 8f815cdde3e550e10c2736990d791f60c2ce43eb upstream.

A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.

Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.

Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.

Fixes: 026331c4d9b5 ("cfg80211/mac80211: allow registering for and sending action frames")
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Update TM user feature bits in scan_features()

commit 4705e02498d6d5a7ab98dfee9595cd5e91db2017 upstream.

We need to update the user TM feature bits (PPC_FEATURE2_HTM and
PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature
bit.

At the moment, if firmware reports TM is not available we turn off
the kernel TM feature bit but leave the userspace ones on. Userspace
thinks it can execute TM instructions and it dies trying.

This (together with a QEMU patch) fixes PR KVM, which doesn't currently
support TM.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Update cpu_user_features2 in scan_features()

commit beff82374b259d726e2625ec6c518a5f2613f0ae upstream.

scan_features() updates cpu_user_features but not cpu_user_features2.

Amongst other things, cpu_user_features2 contains the user TM feature
bits which we must keep in sync with the kernel TM feature bit.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: scan_features() updates incorrect bits for REAL_LE

commit 6997e57d693b07289694239e52a10d2f02c3a46f upstream.

The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU
feature value, meaning all the remaining elements initialise the wrong
values.

This means instead of checking for byte 5, bit 0, we check for byte 0,
bit 0, and then we incorrectly set the CPU feature bit as well as MMU
feature bit 1 and CPU user feature bits 0 and 2 (5).

Checking byte 0 bit 0 (IBM numbering), means we're looking at the
"Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU.
In practice that bit is set on all platforms which have the property.

This means we set CPU_FTR_REAL_LE always. In practice that seems not to
matter because all the modern cpus which have this property also
implement REAL_LE, and we've never needed to disable it.

We're also incorrectly setting MMU feature bit 1, which is:

#define MMU_FTR_TYPE_8xx 0x00000002

Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E
code, which can't run on the same cpus as scan_features(). So this also
doesn't matter in practice.

Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2
is not currently used, and bit 0 is:

#define PPC_FEATURE_PPC_LE 0x00000001

Which says the CPU supports the old style "PPC Little Endian" mode.
Again this should be harmless in practice as no 64-bit CPUs implement
that mode.

Fix the code by adding the missing initialisation of the MMU feature.

Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It
would be unsafe to start using it as old kernels incorrectly set it.

Fixes: 44ae3ab3358e ("powerpc: Free up some CPU feature bits by moving out MMU-related features")
Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: Flesh out changelog, add comment reserving 0x4]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: talitos - fix AEAD tcrypt tests

commit 340ff60ae93a5db2b2be6f38868df9a1293b6007 upstream.

After conversion to new AEAD interface, tcrypt tests fail as follows:

[...]
[    1.145414] alg: aead: Test 1 failed on encryption for authenc-hmac-sha1-cbc-aes-talitos
[    1.153564] 00000000: 53 69 6e 67 6c 65 20 62 6c 6f 63 6b 20 6d 73 67
[    1.160041] 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    1.166509] 00000020: 00 00 00 00
[...]

Fix them by providing the correct cipher in & cipher out pointers,
i.e. must skip over associated data in src and dst S/G.

While here, fix a problem with the HW S/G table index usage:
tbl_off must be updated after the pointer to the table entries is set.

Fixes: aeb4c132f33d ("crypto: talitos - Convert to new AEAD interface")
Reported-by: Jonas Eymann <J.Eymann@gmx.net>
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: talitos - fix crash in talitos_cra_init()

commit 89d124cb61b39900959e2839ac06b6339b6a54cb upstream.

Conversion of talitos driver to the new AEAD interface
hasn't been properly tested.

AEAD algorithms crash in talitos_cra_init as follows:

[...]
[    1.141095] talitos ffe30000.crypto: hwrng
[    1.145381] Unable to handle kernel paging request for data at address 0x00000058
[    1.152913] Faulting instruction address: 0xc02accc0
[    1.157910] Oops: Kernel access of bad area, sig: 11 [#1]
[    1.163315] SMP NR_CPUS=2 P1020 RDB
[    1.166810] Modules linked in:
[    1.169875] CPU: 0 PID: 1007 Comm: cryptomgr_test Not tainted 4.4.6 #1
[    1.176415] task: db5ec200 ti: db4d6000 task.ti: db4d6000
[    1.181821] NIP: c02accc0 LR: c02acd18 CTR: c02acd04
[    1.186793] REGS: db4d7d30 TRAP: 0300   Not tainted  (4.4.6)
[    1.192457] MSR: 00029000 <CE,EE,ME>  CR: 95009359  XER: e0000000
[    1.198585] DEAR: 00000058 ESR: 00000000
GPR00: c017bdc0 db4d7de0 db5ec200 df424b48 00000000 00000000 df424bfc db75a600
GPR08: df424b48 00000000 db75a628 db4d6000 00000149 00000000 c0044cac db5acda0
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000400 df424940
GPR24: df424900 00003083 00000400 c0180000 db75a640 c03e9f84 df424b40 df424b48
[    1.230978] NIP [c02accc0] talitos_cra_init+0x28/0x6c
[    1.236039] LR [c02acd18] talitos_cra_init_aead+0x14/0x28
[    1.241443] Call Trace:
[    1.243894] [db4d7de0] [c03e9f84] 0xc03e9f84 (unreliable)
[    1.249322] [db4d7df0] [c017bdc0] crypto_create_tfm+0x5c/0xf0
[    1.255083] [db4d7e10] [c017beec] crypto_alloc_tfm+0x98/0xf8
[    1.260769] [db4d7e40] [c0186a20] alg_test_aead+0x28/0xc8
[    1.266181] [db4d7e60] [c0186718] alg_test+0x260/0x2e0
[    1.271333] [db4d7ee0] [c0183860] cryptomgr_test+0x30/0x54
[    1.276843] [db4d7ef0] [c0044d80] kthread+0xd4/0xd8
[    1.281741] [db4d7f40] [c000e4a4] ret_from_kernel_thread+0x5c/0x64
[    1.287930] Instruction dump:
[    1.290902] 38600000 4e800020 81230028 7c681b78 81490010 38e9ffc0 3929ffe8 554a073e
[    1.298691] 2b8a000a 7d474f9e 812a0008 91230030 <80e90058> 39270060 7c0004ac 7cc04828

Fixes: aeb4c132f33d ("crypto: talitos - Convert to new AEAD interface")
Signed-off-by: Jonas Eymann <J.Eymann@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix typo - replaced parameter of __crypto_ahash_alg(): s/tfm/alg
Remove checkpatch warnings.
Add commit message.

Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: sha1-mb - use corrcet pointer while completing jobs

commit 0851561d9c965df086ef8a53f981f5f95a57c2c8 upstream.

In sha_complete_job, incorrect mcryptd_hash_request_ctx pointer is used
when check and complete other jobs. If the memory of first completed req
is freed, while still completing other jobs in the func, kernel will
crash since NULL pointer is assigned to RIP.

Signed-off-by: Xiaodong Liu <xiaodong.liu@intel.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: ccp - Prevent information leakage on export

commit f709b45ec461b548c41a00044dba1f1b572783bf upstream.

Prevent information from leaking to userspace by doing a memset to 0 of
the export state structure before setting the structure values and copying
it. This prevents un-initialized padding areas from being copied into the
export area.

Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix memory leak in paging

commit 7fdf9663261cc77a516396fec82cee8a8ea07e76 upstream.

Currently paging download buffer is freed during the
the unloading of the opmode which happens when the driver
is unloaded.

This causes a memory leak since the paging download
buffer is allocated every time we enable the
interface, so the download buffer can be allocated many
times, but only be freed once.

Free paging download buffer during disabling of the
interface.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: pcie: lower the debug level for RSA semaphore access

commit 9fc515bc9e735c10cd327f05c20f5ef69474188d upstream.

IWL_INFO is not an error but still printed by default.
"can't access the RSA semaphore it is write protected" seems
worrisome but it is not really a problem.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/pci: add extra padding to function measurement block

commit 9d89d9e61d361f3adb75e1aebe4bb367faf16cfa upstream.

Newer machines might use a different (larger) format for function
measurement blocks. To ensure that we comply with the alignment
requirement on these machines and prevent memory corruption (when
firmware writes more data than we expect) add 16 padding bytes
at the end of the fmb.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: intel_pstate: Fix processing for turbo activation ratio

commit 1becf03545a0859ceaaf9e8c2d9861882a71cb01 upstream.

When the config TDP level is not nominal (level = 0), the MSR values for
reading level 1 and level 2 ratios contain power in low 14 bits and actual
ratio bits are at bits [23:16]. The current processing for level 1 and
level 2 is wrong as there is no shift done to get actual ratio.

Fixes: 6a35fc2d6c22 (cpufreq: intel_pstate: get P1 from TAR when available)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "drm/amdgpu: disable runtime pm on PX laptops without dGPU power control"

commit e9bef455af8eb0e837e179aab8988ae2649fd8d3 upstream.

This reverts commit bedf2a65c1aa8fb29ba8527fd00c0f68ec1f55f1.

See the radeon revert for an extended description.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"

commit bfaddd9fc8ac048b99475f000dbef6f08297417f upstream.

This reverts commit e64c952efb8e0c15ae82cec8e455ab4910690ef1.

ATPX is the ACPI method for controlling AMD PowerXpress laptops.
There are flags to indicate which methods are supported.  If
the dGPU power down flag is not supported, the driver needs to
implement the dGPU power down manually.  We had previously
always forced the driver to assume the ATPX dGPU power down
was present, but this causes problems on boards where it is
not, leading to GPU hangs when attempting to power down the
dGPU.  Manual dGPU power down is not currently supported in
the Linux driver.  Some laptops indicate that the ATPX
dGPU power down method is not present, but it actually
apparently is.  I'm not sure if this is a bios bug and it should
be set or if there is a reason it was unset and the method should
not be used.  This is not an issue on other OSes since both the
ATPX and the manual driver power down methods are supported.

This is apparently fairly widespread, so just revert for now.

bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=115321
https://bugzilla.kernel.org/show_bug.cgi?id=116581
https://bugzilla.kernel.org/show_bug.cgi?id=116251

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>