Marc Kleine-Budde [Thu, 29 Apr 2010 23:19:35 +0000 (01:19 +0200)]
mx35: adjust flexcan clock definition
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Marc Kleine-Budde [Thu, 22 Jul 2010 09:41:56 +0000 (11:41 +0200)]
mx25: add flexcan address and interrupt definition
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer [Wed, 22 Jul 2009 15:33:36 +0000 (17:33 +0200)]
mx25: flexcan clock support
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 20 Jul 2010 07:16:13 +0000 (09:16 +0200)]
iomux-mx51: add 4 pin definitions
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 21 Jul 2010 12:46:11 +0000 (14:46 +0200)]
i.MX51: handle IRQ for gpio 16..31
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Mon, 19 Jul 2010 07:45:17 +0000 (09:45 +0200)]
eukrea_mbimx27-baseboard: fix compile when CONFIG_SPI_IMX is disabled
the i2c_board_info structure landed into the SPI #if/#endif
which is wrong.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 16 Jul 2010 13:09:07 +0000 (15:09 +0200)]
imxfb: add pwmr controlled backlight support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 16 Jul 2010 13:09:06 +0000 (15:09 +0200)]
imx25: fix low level debug
DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Thu, 17 Jun 2010 18:59:07 +0000 (20:59 +0200)]
mxcmmc: convert to pm_ops and enable/disable clock
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: s.hauer@pengutronix.de
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Wed, 14 Jul 2010 13:24:54 +0000 (21:24 +0800)]
mx51_3ds: add keypad support on 3ds platform
Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Wed, 14 Jul 2010 13:24:53 +0000 (21:24 +0800)]
mx51: add imx_keypad device definition for mx51 platforms
add imx_keypad platform device definition and clocks for mx51
platforms.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Wed, 14 Jul 2010 13:24:52 +0000 (21:24 +0800)]
mx51_3ds: Add support for the imx51 3-stack board
3-stack is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.
Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rogerio Pimentel [Fri, 25 Jun 2010 13:31:33 +0000 (10:31 -0300)]
mx27_3ds: add support for the keypad
mx27_3ds: add support for the keypad
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Thu, 24 Jun 2010 13:11:29 +0000 (21:11 +0800)]
mx31_3ds: revert 3ds debug board relate code
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Thu, 24 Jun 2010 13:11:28 +0000 (21:11 +0800)]
mxc: add common debug board for 3-stack platforms
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Wed, 30 Jun 2010 10:16:24 +0000 (12:16 +0200)]
Merge branch 'imx/for-2.6.36' of git://git.pengutronix.de/git/ukl/linux-2.6 into HEAD
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
Baruch Siach [Thu, 24 Jun 2010 08:57:03 +0000 (11:57 +0300)]
mx25: add PWM4 to iomux
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Thu, 24 Jun 2010 08:57:02 +0000 (11:57 +0300)]
mx25: add iomux defines for UART4 on KPP pins
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fabio Estevam [Mon, 21 Jun 2010 20:33:05 +0000 (13:33 -0700)]
mx31_3ds: Handle USB OTG GPIO Errors
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Mon, 21 Jun 2010 05:16:00 +0000 (08:16 +0300)]
mx25: add support for the CSI device
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Mon, 21 Jun 2010 05:15:59 +0000 (08:15 +0300)]
mx27: add support for the CSI device
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Luotao Fu [Fri, 18 Jun 2010 07:23:19 +0000 (09:23 +0200)]
pca100: clean up GPIO pin multiplexing
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Luotao Fu [Fri, 18 Jun 2010 07:23:18 +0000 (09:23 +0200)]
pca100: add framebuffer device support and TFT
this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Sat, 12 Jun 2010 14:22:39 +0000 (22:22 +0800)]
mxc/iomux: add GPIO bank offset for iomux v3 platforms
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Sat, 12 Jun 2010 14:22:38 +0000 (22:22 +0800)]
mx51/iomux: add UART and GPIO pad definitions for imx51_3ds board
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jason Wang [Sat, 12 Jun 2010 14:22:37 +0000 (22:22 +0800)]
mx51/iomux: Fix mux mode and input path for two pads
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Amit Kucheria [Wed, 16 Jun 2010 11:00:15 +0000 (14:00 +0300)]
[PATCH] mxc: Fix pad names for imx51
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Thu, 10 Jun 2010 14:07:50 +0000 (16:07 +0200)]
i.MX35: add cpuimx35 support and its baseboard
* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host,
USB OTG and I2C touchscreen controller
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Thu, 10 Jun 2010 09:14:32 +0000 (12:14 +0300)]
mx25: add a comment documenting undocumented IPG clocks
The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Wed, 9 Jun 2010 11:07:01 +0000 (14:07 +0300)]
mx25pdk: register watchdog device
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Thu, 10 Jun 2010 09:32:15 +0000 (12:32 +0300)]
mx25: add watchdog clock
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:03:01 +0000 (11:03 +0200)]
i.MX25: add cpuimx25 module and its baseboard
* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:03:00 +0000 (11:03 +0200)]
i.MX25: add AUDMUX and SSI support
* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:59 +0000 (11:02 +0200)]
i.MX25: fix USB gadget support
i.MX25's udc port is the same as i.MX35's one
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:58 +0000 (11:02 +0200)]
i.MX25: fix EHCI support
i.MX25's EHCI is the same as i.MX35's one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:57 +0000 (11:02 +0200)]
i.MX25: fix get_rate_otg to return the correct value
usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:56 +0000 (11:02 +0200)]
plat-mxc/ehci.c: add i.MX25 support
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 09:02:55 +0000 (11:02 +0200)]
MX25: put define for OTG base address in right include
the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 1 Jun 2010 19:57:44 +0000 (21:57 +0200)]
i.MX27: add suspend to RAM support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Sun, 20 Jun 2010 19:22:54 +0000 (21:22 +0200)]
eukrea_mbimx27: fix audio support when SOC is compiled as module
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Fri, 18 Jun 2010 14:19:55 +0000 (16:19 +0200)]
mach-cpuimx27: fix USB_ULPI build warnings
when CONFIG_USB_ULPI is not defined we actually get :
warning: 'otg_pdata' defined but not used
warning: 'usbh2_pdata' defined but not used
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: s.hauer@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Tue, 8 Jun 2010 16:07:05 +0000 (18:07 +0200)]
i.MX35: return IPU clock's value for mx3fb
without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Dinh Nguyen [Thu, 27 May 2010 15:45:05 +0000 (10:45 -0500)]
mx5: Register i2c on Freescale MX51 Babbage HW
Add device registration and setup IOMUX pins in the mx51_babbage
board feil.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Dinh Nguyen [Thu, 27 May 2010 15:45:04 +0000 (10:45 -0500)]
mx5: Add i2c to Freescale MX51 Babbage HW
This patch adds I2C functionality to the Freescale MX51 Babbage HW.
The patch adds device structures, i2c board slave device defines,
IOMUX pin defines, and clocks.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Amit Kucheria [Fri, 28 May 2010 08:29:09 +0000 (11:29 +0300)]
arm: mxc: utilise usecount field in clock operations
This patch fixes the clock refcounting when reparenting is used.
Boot-tested on imx51 babbage board.
Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.html
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Wed, 26 May 2010 12:12:11 +0000 (15:12 +0300)]
mx25pdk: add keypad support
The keymap is taken from the Freescale supplied kernel.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Wed, 26 May 2010 12:12:10 +0000 (15:12 +0300)]
mx25: add platform code for imx-keypad
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Baruch Siach [Mon, 31 May 2010 05:49:40 +0000 (08:49 +0300)]
mxc_nand: add support for platform defined partitions
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer [Tue, 27 Apr 2010 13:24:01 +0000 (15:24 +0200)]
mxc_nand: Fix OOB handling
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Eric Bénard [Thu, 27 May 2010 08:58:56 +0000 (10:58 +0200)]
eukrea_mbimx27: add audio codec
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:07 +0000 (18:46 +0200)]
eukrea_mbimx27: add support for the keyboard
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:06 +0000 (18:46 +0200)]
MX2X: Add Keypad device definition for MX2X arch
Based on work from Alberto Panizzo for MX3X
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:05 +0000 (18:46 +0200)]
eukrea_mbimx27: use card detect through DAT3 for SDHC1
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:04 +0000 (18:46 +0200)]
mxcmmc: add card detect through DAT3 possibility
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:03 +0000 (18:46 +0200)]
mach-cpuimx27: register wdt and w1_master resources
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:02 +0000 (18:46 +0200)]
mach-cpuimx27: add USB Host2 and OTG support
support copied from mach-pca100.c
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Thu, 20 May 2010 07:22:28 +0000 (09:22 +0200)]
eukrea_mbimx27: fix ADS7846 support
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:46:00 +0000 (18:46 +0200)]
mach-cpuimx27: fix QuadUART's IRQ typo in pins'setup
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:59 +0000 (18:45 +0200)]
cpuimx27 and mbimx27: allow fine control of UART4 and SDHC2 usage
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:58 +0000 (18:45 +0200)]
eukrea_mbimx27-baseboard: add timings for DVI output
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:57 +0000 (18:45 +0200)]
eukrea_mbimx27-baseboard: add generic-bl and platform-lcd controls
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard [Wed, 19 May 2010 16:45:56 +0000 (18:45 +0200)]
eukrea_mbimx27-baseboard: fix typo in display name
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wolfram Sang [Fri, 21 May 2010 04:52:06 +0000 (06:52 +0200)]
pcm037/pcm043/pca100: fix ULPI-related build warnings
Like this one (if CONFIG_USB_ULPI is not set):
arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Daniel Mack [Tue, 25 May 2010 14:46:56 +0000 (16:46 +0200)]
ARM: mx3: mx31lilly: pass mc13783 SPI IRQ pin
This makes the resistive touch interface work.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König [Wed, 23 Jun 2010 09:57:19 +0000 (11:57 +0200)]
ARM: mx3: complement uart init routine with an exit routine
moboard_uart0_init requests a gpio. Without an exit function that
frees that gpio again binding the uart a second time doesn't work.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 23 Jun 2010 09:49:34 +0000 (11:49 +0200)]
ARM: imx: dynamically register imx-uart devices (imx35)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 23 Jun 2010 09:46:16 +0000 (11:46 +0200)]
ARM: imx: dynamically register imx-uart devices (imx31)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 23 Jun 2010 07:36:01 +0000 (09:36 +0200)]
ARM: imx: dynamically register imx-uart devices (imx27)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Thu, 24 Jun 2010 13:20:44 +0000 (15:20 +0200)]
ARM: imx: dynamically register imx-uart devices (imx25)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 15:59:58 +0000 (17:59 +0200)]
ARM: imx: dynamically register imx-uart devices (imx21)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 12:50:59 +0000 (14:50 +0200)]
ARM: imx: dynamically register imx-uart devices (imx1)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 12:49:20 +0000 (14:49 +0200)]
ARM: imx: dynamically register imx-uart devices (generic part)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 08:14:15 +0000 (10:14 +0200)]
ARM: imx: dynamically register spi_imx devices (imx35)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 08:09:14 +0000 (10:09 +0200)]
ARM: imx: dynamically register spi_imx devices (imx31)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 07:00:22 +0000 (09:00 +0200)]
ARM: imx: dynamically register spi_imx devices (imx27)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Mon, 21 Jun 2010 15:34:58 +0000 (17:34 +0200)]
ARM: imx: dynamically register spi_imx devices (imx25)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Mon, 21 Jun 2010 15:27:22 +0000 (17:27 +0200)]
ARM: imx: dynamically register spi_imx devices (imx21)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Mon, 21 Jun 2010 16:02:55 +0000 (18:02 +0200)]
ARM: imx: dynamically register spi_imx devices (generic part)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 17:25:34 +0000 (19:25 +0200)]
ARM: imx: dynamically register imx-i2c devices (imx35)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 16:03:05 +0000 (18:03 +0200)]
ARM: imx: dynamically register imx-i2c devices (imx31)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 15:25:40 +0000 (17:25 +0200)]
ARM: imx: dynamically register imx-i2c devices (imx27)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 12:55:07 +0000 (14:55 +0200)]
ARM: imx: dynamically register imx-i2c devices (imx25)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 22 Jun 2010 07:27:33 +0000 (09:27 +0200)]
ARM: imx: dynamically register imx-i2c devices (imx21)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 13:26:07 +0000 (15:26 +0200)]
ARM: imx: dynamically register imx-i2c devices (imx1)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 12:37:51 +0000 (14:37 +0200)]
ARM: imx: dynamically register imx-i2c devices (generic part)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 10:26:53 +0000 (12:26 +0200)]
ARM: imx: Change the way nand devices are registered (imx35)
Make use of new mechanism to register a nand device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 10:23:11 +0000 (12:23 +0200)]
ARM: imx: Change the way nand devices are registered (imx31)
Make use of new mechanism to register a nand device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 05:35:31 +0000 (07:35 +0200)]
ARM: imx: Change the way nand devices are registered (imx27)
Make use of new mechanism to register a nand device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 10:34:56 +0000 (12:34 +0200)]
ARM: imx: Change the way nand devices are registered (imx25)
Make use of new mechanism to register a nand device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 09:17:45 +0000 (11:17 +0200)]
ARM: imx: Change the way nand devices are registered (imx21)
Make use of new mechanism to register a nand device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 15 Jun 2010 16:14:19 +0000 (18:14 +0200)]
ARM: imx: Change the way nand devices are registered (generic part)
Instead of having a platform device defined in a devices.c and register
it in the machine file allocate it dynamically. This reduces the size
of needed memory as the new function is discarded after init and only
the existing devices are created.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 05:12:51 +0000 (07:12 +0200)]
ARM: mxc: remove paragraphs with old address of the FSF
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 05:06:49 +0000 (07:06 +0200)]
ARM: mxc91231: remove paragraphs with old address of the FSF
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 04:59:45 +0000 (06:59 +0200)]
ARM: mx3: remove paragraphs with old address of the FSF
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 04:53:33 +0000 (06:53 +0200)]
ARM: mx25: remove paragraphs with old address of the FSF
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 04:53:33 +0000 (06:53 +0200)]
ARM: imx: remove paragraphs with old address of the FSF
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Wed, 16 Jun 2010 04:45:15 +0000 (06:45 +0200)]
MTD: mxc_nand: make bit fields unsigned to please sparse
This fixes:
arch/arm/plat-mxc/include/mach/mxc_nand.h:25:14: error: dubious one-bit signed bitfield
arch/arm/plat-mxc/include/mach/mxc_nand.h:26:17: error: dubious one-bit signed bitfield
While at it make width unsigned, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Tue, 15 Jun 2010 09:31:02 +0000 (11:31 +0200)]
ARM: imx: new helper function imx_add_platform_device
This should be a globally available function, see
http://thread.gmane.org/gmane.linux.kernel/998881/focus=998882
Until this hits mainline create a similar function available for imx
platforms only.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Mon, 14 Jun 2010 15:56:52 +0000 (17:56 +0200)]
ARM: imx: new Kconfig symbol and feature test macro for DMA on mx1 and mx2
This should be used instead of hard coding the corresponding platforms.
The feature test macro is needed to support different SOCs in a single
kernel image. While at it rename dma-mx1-mx2 to dma-v1 as mx25 doesn't
use it and so the mx2 part is wrong and move the header to
arch/arm/mach-imx.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König [Mon, 14 Jun 2010 15:39:21 +0000 (17:39 +0200)]
ARM: imx: prepare deprecating ARCH_MX1, MACH_MX2, MACH_MX21 and MACH_MX27
MACH_... is reserved for machine support, so use SOC as prefix, not MACH.
This introduces new symbols SOC_IMX1, SOC_IMX21 and SOC_IMX27. They are
selected by the old symbols for now. There is no substitute for MACH_MX2
as most usages of MX2 only means MX21 + MX27 but not MX25.
Later the choice about CPU and CPU family should go away and the individual
machines should select the right SOC symbol. This is a precondition to
support more than one SOC in a single kernel image.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
projects / firefly-linux-kernel-4.4.55.git / log