USB: remove CONFIG_USB_DEBUG from defconfig files

Now that CONFIG_USB_DEBUG is gone, remove it from a number of defconfig
files that were enabling it.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: resume child device when port is powered on

Unconditionally wake up the child device when the power session is
recovered.

This addresses the following scenarios:

1/ The device may need a reset on power-session loss, without this
   change port power-on recovery exposes khubd to scenarios that
   usb_port_resume() is set to handle.  Prior to port power control the
   only time a power session would be lost is during dpm_suspend of the
   hub.  In that scenario usb_port_resume() is guaranteed to be called
   prior to khubd running for that port.  With this change we wakeup the
   child device as soon as possible (prior to khubd running again for this
   port).

   Although khubd has facilities to wake a child device it will only do
   so if the portstatus / portchange indicates a suspend state.  In the
   case of port power control we are not coming from a hub-port-suspend
   state.  This implementation simply uses pm_request_resume() to wake the
   device and relies on the port_dev->status_lock to prevent any collisions
   between khubd and usb_port_resume().

2/ This mechanism rate limits port power toggling.  The minimum port
   power on/off period is now gated by the child device suspend/resume
   latency.  Empirically this mitigates devices downgrading their connection
   on perceived instability of the host connection.  This ratelimiting is
   really only relevant to port power control testing, but it is a nice
   side effect of closing the above race.  Namely, the race of khubd for
   the given port running while a usb_port_resume() event is pending.

3/ Going forward we are finding that power-session recovery requires
   warm-resets (http://marc.info/?t=138659232900003&r=1&w=2).  This
   mechanism allows for warm-resets to be requested at the same point in
   the resume path for hub dpm_suspend power session losses, or port
   rpm_suspend power session losses.

4/ If the device *was* disconnected the only time we'll know for sure is
   after a failed resume, so it's necessary for usb_port_runtime_resume()
   to expedite a usb_port_resume() to clean up the removed device.  The
   reasoning for this is "least surprise" for the user. Turning on a port
   means that hotplug detection is again enabled for the port, it is
   surprising that devices that were removed while the port was off are not
   disconnected until they are attempted to be used.  As a user "why would
   I try to use a device I removed from the system?"

1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume.  For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.

Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control).   Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().

Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device.  To this end we hold the
port active with the "child_usage" reference across the disconnect
event.  Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).

Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y

Per Alan:
"You mean from within hub_handle_remote_wakeup()?  That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.

In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: introduce port status lock

In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:

if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
    udev->state != USB_STATE_NOTATTACHED) {
if (portstatus & USB_PORT_STAT_ENABLE) {
/* Nothing to do */
} else if (udev->state == USB_STATE_SUSPENDED &&
udev->persist_enabled) {
...
} else {
/* Don't resuscitate */;
}
}

...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.

So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset.  The lock ordering
rules are now usb_lock_device() => usb_lock_port().  This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port.  We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock.  The lock is also dropped/re-acquired during
hub_port_reconnect().

This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: synchronize port poweroff and khubd

If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it.  Otherwise, the following sequence of events
leading to an unintended disconnect may occur:

Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5

Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
    hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: refactor port handling in hub_events()

In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.

We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.

This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.

Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: usb3 ports do not support FEAT_C_ENABLE

The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: don't clear FEAT_C_ENABLE on usb_port_runtime_resume failure

Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
   state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
   a matter of course

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: block suspension of superspeed port while hispeed peer is active

ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state.  There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection.  Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.

By default the latency between peer power-on events is 0.  In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay.  In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.

Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: make usb_port flags atomic, rename did_runtime_put to child_usage

We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates.  Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: sysfs link peer ports

The usb topology after this change will have symlinks between usb3 ports
and their usb2 peers, for example:

usb2/2-1/2-1:1.0/2-1-port1/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port1
usb2/2-1/2-1:1.0/2-1-port2/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port2
usb2/2-1/2-1:1.0/2-1-port3/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port3
usb2/2-1/2-1:1.0/2-1-port4/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port4
usb2/2-0:1.0/usb2-port1/peer    => ../../../usb3/3-0:1.0/usb3-port1
usb2/2-0:1.0/usb2-port2/peer    => ../../../usb3/3-0:1.0/usb3-port2
usb2/2-0:1.0/usb2-port3/peer    => ../../../usb3/3-0:1.0/usb3-port3
usb2/2-0:1.0/usb2-port4/peer    => ../../../usb3/3-0:1.0/usb3-port4

usb3/3-1/3-1:1.0/usb3-1-port1/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port1
usb3/3-1/3-1:1.0/usb3-1-port2/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port2
usb3/3-1/3-1:1.0/usb3-1-port3/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port3
usb3/3-1/3-1:1.0/usb3-1-port4/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port4
usb3/3-0:1.0/usb3-port1/peer       => ../../../usb2/2-0:1.0/usb2-port1
usb3/3-0:1.0/usb3-port2/peer       => ../../../usb2/2-0:1.0/usb2-port2
usb3/3-0:1.0/usb3-port3/peer       => ../../../usb2/2-0:1.0/usb2-port3
usb3/3-0:1.0/usb3-port4/peer       => ../../../usb2/2-0:1.0/usb2-port4

Introduce link_peers_report() to notify on all link_peers() failure
cases.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: find internal hub tier mismatch via acpi

ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value.  If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs.  External hubs follow the default peer
association scheme.

Location data is cached as an opaque cookie in usb_port_location data.

Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.

When we find port location data for a port then we assume that the
firmware will also describe its peer port.  This allows the
implementation to only ever set the peer once.  This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving.  Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).

There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.

[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8

[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: assign usb3 external hub port peers

Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:

1/ ascend to the parent hub and find the upstream port_dev

2/ walk ->peer to find the peer port

3/ descend to the peer hub via ->child

4/ find the port with the matching port id

Note that this assumes the port labeling scheme required by the
specification [1].

[1]: usb3 3.1 section 10.3.3

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: assign default peer ports for root hubs

Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub.  This identification scheme is required of
external hubs by the USB3 spec [1].  However, for root hubs, tier mismatch
may be in effect [2].  Tier mismatch can only be enumerated via platform
firmware.  For now, simply perform the nominal association.

A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups.  It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.

[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D

Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cleanup setting udev->removable from port_dev->connect_type

Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().

This also changes behavior in the case where the firmware says that the
port connect type is unknown.  In that case just use the default setting
determined from the hub descriptor.

Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: rename usb_port device objects

The current port name "portX" is ambiguous.  Before adding more port
messages rename ports to "<hub-device-name>-portX"

This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction.  If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.

Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
dev_XXX(hub->intfdev, ..."port %d"...
dev_XXX(&hdev->dev, ..."port%d"...
into:
dev_XXX(&port_dev->dev, ...

Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb.  However, it turns out that this
breaks 'lsusb -t'.  For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".

Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: disable port power control if not supported in wHubCharacteristics

A hub indicates whether it supports per-port power control via the
wHubCharacteristics field in its descriptor.  If it is not supported
a hub will still emulate ClearPortPower(PORT_POWER) requests by
stopping the link state machine.  However, since this does not save
power do not bother suspending.

This also consolidates support checks into a
hub_is_port_power_switchable() helper.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: mutual exclusion for resetting a hub and power-managing a port

The USB core doesn't properly handle mutual exclusion between
resetting a hub and changing the power states of the hub's ports.  We
need to avoid sending port-power requests to the hub while it is being
reset, because such requests cannot succeed.

This patch fixes the problem by keeping track of when a reset is in
progress.  At such times, attempts to suspend (power-off) a port will
fail immediately with -EBUSY, and calls to usb_port_runtime_resume()
will update the power_is_on flag and return immediately.  When the
reset is complete, hub_activate() will automatically restore each port
to the proper power state.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: pci_quirks: fix sparse 'symbol not declared' warning

This commit fixes the following sparse warning:

drivers/usb/host/pci-quirks.c:
    - 252: warning: symbol 'usb_hcd_amd_remote_wakeup_quirk' was not
      declared. Should it be static?

This function is exported so the fix was to add it's declaration to the
header file.

Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: rename CONFIG_USB_GADGET_PXA25X

Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit
c0a39151a405 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.

Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: storage: ene_ub6250: Use kmemdup instead of kmalloc + memcpy

This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci

Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: usbtest: add pattern check on pipe in phase of unlink read

TEST 11 unlinks the URB read request for N times. When host and gadget
both initialize pattern 1 (mod 63) data series to do IN transfer, the
host side function should check the data buffer if it is as mod 63
series, because the data packet which host receivced will follow
pattern 1. So this patch adds this checking action.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: usbtest: fix unlink write error with pattern 1

TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected.  Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.

[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0

Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: usb5303: add support for reference clock specified in device tree

USB3503 chip supports 8 values of reference clock. The value is
specified by REF_SEL[1:0] pins and INT_N line. This patch add support
for getting 'refclk' clock, enabling it and setting INT_N line according
to the value of the gathered clock. If no clock has been specified,
driver defaults to the old behaviour (assuming that clock has been
specified by REF_SEL pins from primary reference clock frequencies
table).

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: separate usb_address0 mutexes for each bus

This patch creates a separate instance of the usb_address0 mutex for each USB
bus, and attaches it to the usb_bus device struct. This allows devices on
separate buses to be enumerated in parallel; saving time.

In the current code, there is a single, global instance of the usb_address0
mutex which is used for all devices on all buses. This isn't completely
necessary, as this mutex is only needed to prevent address0 collisions for
devices on the *same* bus (usb 2.0 spec, sec 4.6.1). This superfluous coverage
can cause additional delay in system resume on systems with multiple hosts
(up to several seconds depending on what devices are attached).

Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Switch only Intel Lynx Point-LP ports to EHCI on shutdown.

Patch "xhci: Switch Intel Lynx Point ports to EHCI on shutdown."
commit c09ec25d3684cad74d851c0f028a495999591279 is not fully correct

It switches both Lynx Point and Lynx Point-LP ports to EHCI on shutdown.
On some Lynx Point machines it causes spurious interrupt,
which wake the system: bugzilla.kernel.org/show_bug.cgi?id=76291

On Lynx Point-LP on the contrary switching ports to EHCI seems to be
necessary to fix these spurious interrupts.

Signed-off-by: Denis Turischev <denis@compulab.co.il>
Reported-by: Wulf Richartz <wulf.richartz@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: delete CONFIG_USB_DEVICEFS from defconfig

It no longer occurs in Kconfig.
USB: remove CONFIG_USB_DEVICEFS(fb28d58b) leaked remove defconfig.

Signed-off-by: Naoki MATSUMOTO <nekomatu+linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: udl: proper error reporting

Parsing device descriptors can fail due to a failed memory
allocation. The error needs to be properly propagated to the
upper layers.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: yurex: fix race between probe() and read()

There's a window during which read() would return 0 instead
of a correct error for no data yet. Reorder initialization
to fix the race.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: appledisplay: fix race between reading and writing from the device

The workqueue handler may call appledisplay_bl_get_brightness() while
user space calls appledisplay_bl_update_status(). As they share a
buffer that must not happen. Use a mutex for mutual exclusion.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usbtmc: fix DMA on stack

send_request_dev_dep_msg_in() use a buffer allocated on the stack.
Fix by kmalloc()ing the buffer.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: use BIT macro

Converting the header to BIT for readability. No functional
change.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: net2280: Add support for PLX USB338X

This patch adds support for the PLX USB3380 and USB3382.

This driver is based on the driver from the manufacturer.

Since USB338X is register compatible with NET2280, I thought that it
would be better to include this hardware into net2280 driver.

Manufacturer's driver only supported the USB33X, did not follow the
Kernel Style and contain some trivial errors. This patch has tried to
address this issues.

This patch has only been tested on USB338x hardware, but the merge has
been done trying to not affect the behaviour of NET2280.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: make return of 0 explicit

Delete unnecessary local variable whose value is always 0 and that hides
the fact that the result is always 0.

A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
local idexpression ret;
expression e;
position p;
@@

-ret = 0;
... when != ret = e
return
- ret
+ 0
  ;
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: Enable USB PHY support for arm64

Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: unified loggig of RESET_ON_RESUME

Either we log for all chips we set the quirk for or for
none. This patch reports it for all chips.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci-platform: add optional reset controller retrieval

On the Allwinner's A31 SoC the reset line connected to the EHCI IP has to
be deasserted for the EHCI block to be usable.

Add support for an optional reset controller that will be deasserted on
power off and asserted on power on.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ohci-platform: Enable optional use of reset controller

The OHCI controllers used in the Allwinner A31 are asserted in reset using a
global reset controller.

Add optional support for such a controller in the OHCI platform driver.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ohci: sort out dependencies for lpc32xx and omap

The dependency on the isp1301 driver is not something that
should be in the main OHCI driver but rather the SoC specific
part of it.

This moves the dependency for LPC32xx into USB_OHCI_HCD_LPC32XX,
and changes the 'select ISP1301_OMAP' to a similar 'depends on'.
Since the same dependency exists for the client driver, do the
same change there.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ohci-da8xx can only be built-in

The PHY setup code of the TI DaVinci DA8xx OHCI controller
uses ad-hoc register access using a pointer that is meant to
be used only by the DaVinci platform implementation and that
is intentionally not exported to loadable modules. This results
in a link error on configurations that use a modular OHCI
code on this platform.

While the proper solution for this problem would be to
implement a real PHY driver shared by ohci-da8xx and musb-da8xx,
this patch for now just works around the build error by
only allowing the ohci-da8xx code to be built-in.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: avoid warning for !PM_SLEEP

If we build a kernel with PM_SUSPEND set and no PM_SLEEP,
we get a build warning in the xhci-plat driver about unused
functions.

To fix this, use "#ifdef CONFIG_PM_SLEEP", like we do in most
other drivers nowadays.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Add function to calculate correct FIFO sizes

The dwc2 IP on the SOCFPGA cannot use the default HW configured
FIFO sizes. The total FIFO depth as read from GHWCFG3 reports 0x1f80 or 8064
32-bit words. But the GRXFSIZ, GNPTXFSIZ, and HPTXFSIZ register defaults
to 0x2000 or 8192 32-bit words. So the driver cannot just use the fifo sizes
as read from those registers.

For platforms that face the same issue, this commits sets the RX, periodic TX,
and non-periodic TX fifo size to those that are recommended v2.93a spec for
the DWC2 IP. Implements Method #2 from the Synopsys v2.93a spec for the DWC2.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Disable descriptor dma mode by default

Even though the IP supports Descriptor DMA mode, it does not support SPLIT
transactions in this mode. So the driver, in its currently form, will not
support LS/FS devices when connected to a HS Hub if Descriptor DMA mode is
enabled.

So we should just default to disable descriptor dma mode.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation: dt-bindings: update xhci-platform DT binding

This commit extends the compatible string list of the xhci-platform
binding with the new "armada-375-xhci" and "armada-380-xhci"
compatible strings. It is used to describe the XHCI controller which
is available in the Armada 375 and 38x SoCs.

It also indicates that an optional 'clocks' property is now supported.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: xhci-plat: add support for the Armada 375/38x XHCI controllers

The Armada 375 and 38x SoCs come with an XHCI controller that requires
some specific initialization related to the MBus windows
configuration. This patch adds the support for this special
configuration as an XHCI quirk executed during probe.

Two new compatible strings are added to identify the Armada 375 and
Armada 38x XHCI controllers, and therefore enable the relevant quirk.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: xhci-plat: add clock support

Some platforms (such as the Armada 38x ones) can gate the clock of
their USB controller. This patch adds the support for one clock in
xhci-plat, by enabling it during probe and disabling it on remove.

To achieve this, it adds a 'struct clk *' member in xhci_hcd. While
only used for now in xhci-plat, it might be used by other drivers in
the future. Moreover, the xhci_hcd structure already holds other
members such as msix_count and msix_entries, which are MSI-X specific,
and therefore only used by xhci-pci.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: xhci-plat: sort the headers in alphabetic order

Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers later.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation: dt-bindings: update ehci-orion binding documentation

This commit updates the Device Tree binding documentation of
ehci-orion to take into account the fact that we can now optionally
pass a clock and a PHY reference.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci-orion: add optional PHY support

This commit extends the ehci-orion so that it can optionally be passed
a reference to a PHY through the Device Tree. It will be useful for
the Armada 375 SoCs. If no PHY is provided then the behavior of the
driver is unchanged.

[Thomas: use devm_phy_optional_get() so that we handle -EPROBE_DEFER
properly. Also call phy_power_off() when needed, and rename goto
labels.]

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci-orion: fix clock reference leaking

In order to disable the clock in the ->remove() function, a call to
devm_clk_get() is being made, which further increases the reference
count of the clock.

In order to clean this up, a private structure holding a pointer to
the clock is added using the override mechanism provided by the ehci
framework. This makes the driver clock handling much more logical.

The bug was introduced in v3.6, however the ehci framework allowing to
use the override mechanism has only been introduced in v3.8, so this
patch won't apply before it.

[Thomas: reword commit log, fix goto label names.]

Fixes: 8c869edaee07c623066266827371235fb9c12e01 ('ARM: Orion: EHCI: Add support for enabling clocks')
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci-orion: rename error goto labels in ehci_orion_drv_probe()

In preparation to the introduction of additional initialization steps
in ehci_orion_drv_probe(), we rename the error goto labels from err1,
err2 and err3 names to some more meaningful names.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ehci-orion: use platform_get_irq() for DT probing

Commit 77dae54ab385033e488d8b07045bc7f8d931740f ('ARM: Kirkwood:
ehci-orion: Add device tree binding') added the Device Tree binding
for the ehci-orion driver. To achieve that with the irq, it used the
irq_of_parse_and_map() function when probed in DT-mode, and
platform_get_irq() when probed in non-DT mode.

This is not necessary: platform_get_irq() works just as fine in
DT-mode, since the conversion from DT information to 'struct resource'
is done by the generic layers of the kernel.

Therefore, this commit switches back to use just platform_get_irq().

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: common: rename phy-fsm-usb.c to usb-otg-fsm.c

Since usb otg fsm implementation is not related to usb phy.
We move it from usb/phy/ to usb/common/, and rename it to
reflect its real meaning.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: move usb/usb-common.c to usb/common/usb-common.c

Since we will have more usb-common things, and it will let
usb-common.c be larger and larger, we create a folder named usb/common
for all usb common things.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Remove '0x' notation when using %pad format

%pad notation automatically prints in hexadecimal format (with '0x'), so remove
the unneeded '0x' to avoid a '0x0x' string.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for using a MAX3421E chip as a host driver.

Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: fix variable set but not used warnings

Fix variable set but not used warnings in UWB.

Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: comment typo fix

Comment typo fix.

Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwb: whitespace and line length cleanups

Fix whitespace and line length issues reported by checkpatch.

Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: remove the Kconfig entry for USB_DEBUG

Since we have already removed the usage of CONFIG_USB_DEBUG, it is
meaningless that there is still a configuration entry for CONFIG_USB_DEBUG.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: remove redundant D0 power state set

Pci_enable_device() will set device power state to D0,
so it's no need to do it again after call pci_enable_device().

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: keyspan: fix potential null pointer dereference

Move control-urb dereference to after NULL-check. There is otherwise a
risk of a possible null pointer dereference.

Was largely found by using a static code analysis program called
cppcheck.

[Johan: modify commit message somewhat ]
[gkh: remove stable tag as it's not a real problem that anyone has ever hit]

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: wusbcore: fix control-pipe directions

Fix incorrect pipe directions in control requests (which has been
silently fixed up by USB core).

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: use tty-port dtr_rts

Add dtr_rts tty-port operation which implements proper DTR/RTS handling
(e.g. only lower DTR/RTS during shutdown if HUPCL is set).

Note that modem-control locking still needs to be added throughout the
driver.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: remove redundant usb_mark_last_busy

There's no need to call usb_mark_last_busy after having increased the PM
counter in write(). The device will be marked busy by USB core when the
PM counter is balanced in the completion handler.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: do not update PM busy on read errors

There's no need to update the runtime PM last_busy field on read urb
errors (e.g. when the urb is being killed on shutdown).

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: minimise no-suspend window during shutdown

Now that acm_set_control() handles runtime PM properly, the only
remaining reason for the PM operations in shutdown is to clear the
needs_remote_wakeup flag before the final put.

Note that this also means that we now need to grab the write_lock to
prevent racing with resume.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: remove redundant disconnected test from shutdown

Remove redundant disconnect test from shutdown(), which is never called
post disconnect() where we do synchronous hangup.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: simplify runtime PM locking

We can simply the runtime PM locking as there's no need to check the
susp_count in the read path (at least not since killing the rx tasklet).

Specifically, the read urbs will never be resubmitted by the completion
handler when killed during suspend.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix runtime PM imbalance at shutdown

Make sure only to decrement the PM counters if they were actually
incremented.

Note that the USB PM counter, but not necessarily the driver core PM
counter, is reset when the interface is unbound.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix I/O after failed open

Make sure to kill any already submitted read urbs on read-urb submission
failures in open in order to prevent doing I/O for a closed port.

Fixes: 088c64f81284 ("USB: cdc-acm: re-write read processing")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix failed open not being detected

Fix errors during open not being returned to userspace. Specifically,
failed control-line manipulations or control or read urb submissions
would not be detected.

Fixes: 7fb57a019f94 ("USB: cdc-acm: Fix potential deadlock (lockdep
warning)")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix open and suspend race

We must not do the usb_autopm_put_interface() before submitting the read
urbs or we might end up doing I/O to a suspended device.

Fixes: 088c64f81284 ("USB: cdc-acm: re-write read processing")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix potential urb leak and PM imbalance in write

Make sure to check return value of autopm get in write() in order to
avoid urb leak and PM counter imbalance on errors.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Cc: <stable@vger.kernel.org> # v2.6.27
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix shutdown and suspend race

We should stop I/O unconditionally at suspend rather than rely on the
tty-port initialised flag (which is set prior to stopping I/O during
shutdown) in order to prevent suspend returning with URBs still active.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Cc: <stable@vger.kernel.org> # v2.6.27
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix runtime PM for control messages

Fix runtime PM handling of control messages by adding the required PM
counter operations.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Cc: <stable@vger.kernel.org> # v2.6.27
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix broken runtime suspend

The current ACM runtime-suspend implementation is broken in several
ways:

Firstly, it buffers only the first write request being made while
suspended -- any further writes are silently dropped.

Secondly, writes being dropped also leak write urbs, which are never
reclaimed (until the device is unbound).

Thirdly, even the single buffered write is not cleared at shutdown
(which may happen before the device is resumed), something which can
lead to another urb leak as well as a PM usage-counter leak.

Fix this by implementing a delayed-write queue using urb anchors and
making sure to discard the queue properly at shutdown.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Reported-by: Xiao Jin <jin.xiao@intel.com>
Cc: <stable@vger.kernel.org> # v2.6.27
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix write and resume race

Fix race between write() and resume() due to improper locking that could
lead to writes being reordered.

Resume must be done atomically and susp_count be protected by the
write_lock in order to prevent racing with write(). This could otherwise
lead to writes being reordered if write() grabs the write_lock after
susp_count is decremented, but before the delayed urb is submitted.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Cc: <stable@vger.kernel.org> # v2.6.27
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix write and suspend race

Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.

Specifically, suspend() releases the write_lock after determining the
device is idle but before incrementing the susp_count, thus leaving a
window where a concurrent write() can submit an urb.

Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")

Cc: <stable@vger.kernel.org> # v2.6.27
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: kobil_sct: fix control requests without data stage

Fix incorrect pipe directions and remove bogus data buffer arguments
from control requests without data stage.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: remove overly defensive port tests

The only way a port pointer may be NULL is if probe() failed, and in
that case neither disconnect(), resume(), or reset_resume() will be
called.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: fix potential runtime pm imbalance at device remove

Only call usb_autopm_put_interface() if the corresponding
usb_autopm_get_interface() was successful.

This prevents a potential runtime PM counter imbalance should
usb_autopm_get_interface() fail. Note that the USB PM usage counter is
reset when the interface is unbound, but that the runtime PM counter may
be left unbalanced.

Also add comment on why we don't need to worry about racing
resume/suspend on autopm_get failures.

Fixes: d5fd650cfc7f ("usb: serial: prevent suspend/resume from racing
against probe/remove")

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: do not resume I/O on closing ports

Use tty-port initialised flag rather than private flag to determine when
port is closing down.

Since the tty-port flag is set prior to dropping DTR/RTS (when HUPCL is
set) this avoid submitting the read urbs when resuming the interface in
dtr_rts() only to immediately kill them again in shutdown().

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: report failed submissions as errors

Promote failed-submission messages in open() and write() to error log
level.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: remove bogus function prototype

The usb_wwan_send_setup() function has never existed.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: remove some superfluous comments

Remove some more outdated or superfluous comments.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: remove comment from close

Remove superfluous and cryptic comment from close.

It should be obvious that we're balancing the autopm_put in open (and
that operation already mentions the autopm_get done in the USB serial
core).

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: clean up delayed-urb submission

Clean up and rename delay-urb submission function using a more
descriptive name.

Also add comment on locking assumptions.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: use interface-data accessors

Use usb_get_serial_data() rather than accessing the private pointer
directly.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: make resume error messages uniform

Make resume error messages uniform.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: kill interrupt urb explicitly at suspend

As the port interrupt URB is submitted by the subdriver at open, we
should also kill it explicitly at suspend (even though this will be
taken care of by USB serial core otherwise).

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: remove redundant urb kill from port remove

Remove redundant usb_kill_urb from port remove, which is called
post-shutdown (close).

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: remove unimplemented set_termios

The driver does not implement set_termios so the operation can be left
unset (tty will do the tty_termios_copy_hw for us).

Note that the send_setup call is bogus as it really only sets DTR/RTS
to their current values.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: remove redundant modem-control request

The tty-port implementation has already made sure that DTR/RTS have been
raised by calling dtr_rts so remove the redundant call from open.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix remote wakeup

Make sure that needs_remote_wake up is always set when there are open
ports.

Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).

Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.

Note that there are currently no multi-port drivers using the usb_wwan
implementation.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix discarded writes on resume errors

There's no reason not to try sending off any further delayed write urbs,
should one urb-submission fail.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix potential blocked I/O after resume

Keep trying to submit urbs rather than bail out on first read-urb
submission error, which would also prevent I/O for any further ports
from being resumed.

Instead keep an error count, for all types of failed submissions, and
let USB core know that something went wrong.

Also make sure to always clear the suspended flag. Currently a failed
read-urb submission would prevent cached writes as well as any
subsequent writes from being submitted until next suspend-resume cycle,
something which may not even necessarily happen.

Note that USB core currently only logs an error if an interface resume
failed.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix potential NULL-deref at resume

The interrupt urb was submitted unconditionally at resume, something
which could lead to a NULL-pointer dereference in the urb completion
handler as resume may be called after the port and port data is gone.

Fix this by making sure the interrupt urb is only submitted and active
when the port is open.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Cc: <stable@vger.kernel.org> # v2.6.32: 032129cb03df
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix urb leak at shutdown

The delayed-write queue was never emptied at shutdown (close), something
which could lead to leaked urbs if the port is closed before being
runtime resumed due to a write.

When this happens the output buffer would not drain on close
(closing_wait timeout), and after consecutive opens, writes could be
corrupted with previously buffered data, transfered with reduced
throughput or completely blocked.

Note that unbusy_queued_urb() was simply moved out of CONFIG_PM.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: usb_wwan: fix write and suspend race

Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.

Specifically, suspend() releases the susp_lock after determining the
device is idle but before setting the suspended flag, thus leaving a
window where a concurrent write() can submit an urb.

Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")

Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>