Suman Anna [Thu, 6 Mar 2014 00:24:13 +0000 (18:24 -0600)]
ARM: OMAP2+: use pdata quirks for iommu reset lines
The OMAP iommu driver performs the reset management for the
iommu instances in processor sub-systems using the omap_device
API which are currently supplied as platform data ops. Use pdata
quirks to maintain the functionality as the OMAP iommu driver
gets converted to use DT nodes, until the reset portions are
decoupled from omap_hwmod/omap_device into a separate reset
driver.
This patch adds the pdata quirks for the reset management of
iommus within the DSP (OMAP3 & OMAP4) and IPU subsystems (OMAP4).
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 6 Mar 2014 00:24:12 +0000 (18:24 -0600)]
ARM: OMAP2+: change the ISP device archdata MMU name for DT
The IOMMU DT adaptation support uses the device name instead
of an iommu object name. Fixup the ISP device archdata MMU
name at runtime if using DT-boot. This allows the OMAP3 camera
to be functional in both legacy and DT boots. The iommu object
names should eventually vanish when all the IOMMU users have
been converted to DT nodes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Thu, 6 Mar 2014 00:24:11 +0000 (18:24 -0600)]
ARM: OMAP3: fix iva mmu programming issues
The IVA MMU is not functional when used through the hwmod and
omap_device layers. Add fixes to clockdomain and hwmod data
to have it functional. The hwmod changes are needed to enable
the clock, and the SWSUP change is needed to wakeup the domain
because the power domain is programmed to be in RET, and there
is no automatic power domain switching to ON.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Florian Vaussard [Thu, 6 Mar 2014 00:24:10 +0000 (18:24 -0600)]
ARM: OMAP3: remove deprecated CONFIG_OMAP_IOMMU_IVA2
CONFIG_OMAP_IOMMU_IVA2 was defined originally to avoid conflicting
usage by tidspbridge and other iommu users. The same can be achieved
by marking the DT node disabled, so remove this obsolete flag and
the corresponding hwmod data can be enabled.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: revise commit log]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Yegor Yefremov [Wed, 5 Mar 2014 07:29:19 +0000 (08:29 +0100)]
ARM: dts: am335x-evmsk: enable dual_emac mode
EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Mon, 3 Mar 2014 14:50:23 +0000 (20:20 +0530)]
ARM: dts: DRA7: Add device nodes for ABB
Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andrii.Tseglytskyi [Mon, 3 Mar 2014 14:50:22 +0000 (20:20 +0530)]
ARM: dts: OMAP4: Add device nodes for ABB
Add ABB device nodes for OMAP443x family of devices. abb_iva is
populated, but disabled as it is not used on current OMAP443x family,
but the node is used on OMAP446x family. Data is based on OMAP443x
Technical Reference Manual revision AN (April 2013).
ABB device nodes for OMAP4460 device Data is based on OMAP4460
Technical Reference Manual revision Z (April 2013)
[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andrii.Tseglytskyi [Mon, 3 Mar 2014 14:50:21 +0000 (20:20 +0530)]
ARM: dts: OMAP36xx: Add device node for ABB
Add ABB device node for OMAP36xx family of devices. Data is based on
OMAP36XX Technical Reference Manual revision AB (Dec 2012).
[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Balaji T K [Mon, 3 Mar 2014 14:50:20 +0000 (20:20 +0530)]
ARM: dts: am43x-epos-evm: add SD card hotplug support
Add card detect gpio for SD card slot and include dt gpio header.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Balaji T K [Mon, 3 Mar 2014 14:50:19 +0000 (20:20 +0530)]
ARM: dts: am335x-evm: add SD card hotplug support
Add card detect gpio for SD card slot
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Balaji T K [Mon, 3 Mar 2014 14:50:18 +0000 (20:20 +0530)]
ARM: dts: am437x gp-evm: add sd card dt nodes
enable sd card slot on am437x-gp-evm
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kishon Vijay Abraham I [Mon, 3 Mar 2014 11:38:15 +0000 (17:08 +0530)]
ARM: dts: omap5: added dt properties to adapt to the new phy framwork
Added device tree bindings for dwc3, usb2 and usb3 PHYs. The documentation
of these can be found at Documentation/devicetree/bindings/phy/phy-bindings.txt
and Documentation/devicetree/bindings/phy/ti-phy.txt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Imre Kaloz [Mon, 3 Mar 2014 09:02:56 +0000 (10:02 +0100)]
ARM: OMAP2+: Use pdata quirks for wl12xx on the AM335x EV-MSK
Enable the WiLink6 connected to mmc2.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Thu, 27 Feb 2014 14:18:31 +0000 (16:18 +0200)]
ARM: dts: Update echi-omap DT binding example usage
Remove non-compatible id from examples.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Thu, 27 Feb 2014 14:18:30 +0000 (16:18 +0200)]
ARM: dts: Get rid of incompatible ids for hci-omap USB host nodes
The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Thu, 27 Feb 2014 14:18:29 +0000 (16:18 +0200)]
ARM: OMAP2+: Remove legacy_init_ehci_clk()
The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.
Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Florian Vaussard [Mon, 24 Feb 2014 17:07:48 +0000 (18:07 +0100)]
ARM: dts: Add support for OMAP4 Gumstix DuoVero/Parlor
Gumstix DuoVero is an OMAP4430-based Computer On Module.
Parlor is one of the available expansion board.
Tested features:
- GPMC ethernet
- HSUSB2 and OTG
- Audio out
- WiFi and Bluetooth (w2cbw0015 SDIO module)
- LED and button
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sun, 2 Mar 2014 22:22:03 +0000 (14:22 -0800)]
Merge tag 'for_3.15/dts_signed' of git://git./linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.15/dt
Add craneboard devices
Add more N900 devices
Add am43x-epos-evm and am437x-gp-evm devices
Add OMAP4 DMM devices
Conflicts:
arch/arm/boot/dts/am43x-epos-evm.dts
arch/arm/boot/dts/dra7.dtsi
Archit Taneja [Tue, 17 Dec 2013 10:02:21 +0000 (15:32 +0530)]
ARM: dts: omap4+: Add DMM bindings
Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.
Add documentation for the DMM bindings.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:41 +0000 (18:03 +0530)]
ARM: dts: am43x-gp-evm: Add matrix gpio keys.
Add gpio keys node for am43x gp evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Pekon Gupta [Wed, 5 Feb 2014 13:28:34 +0000 (18:58 +0530)]
ARM: dts: am43xx: add support for parallel NAND flash
This patch:
- enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
- adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
present on following boards:
am43x-epos-evm:
On this board, NAND Flash control lines are muxed with QSPI, Thus only
one of the two can be used at a time. Selection is controlled by:
(a) dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pekon Gupta [Wed, 5 Feb 2014 13:28:32 +0000 (18:58 +0530)]
ARM: dts: AM33xx: updated default ECC scheme in nand-ecc-opt
This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
commit
ac65caf514ec3e55e8d3d510ee37f80dd97418fe
ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pekon Gupta [Wed, 5 Feb 2014 13:28:31 +0000 (18:58 +0530)]
ARM: dts: am335x-evm: NAND: update MTD partition table
This patch has following updates, specific to MTD/NAND DT
- update MTD NAND partition table to keep compatibility between
different boards and mainline u-boot.
- prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
from other MTD device partitions (like NOR and QSPI)
Partition_Name Partition_Size
/dev/mtd0 NAND.SPL 1 block-size*
/dev/mtd1 NAND.SPL.backup1 1 block-size*
/dev/mtd2 NAND.SPL.backup2 1 block-size*
/dev/mtd3 NAND.SPL.backup3 1 block-size*
/dev/mtd5 NAND.u-boot-spl-os 2 block-size* [for falcon boot]
/dev/mtd4 NAND.u-boot 1 MB
/dev/mtd6 NAND.u-boot-env 1 block-size*
/dev/mtd7 NAND.u-boot-env.backup1 1 block-size*
/dev/mtd8 NAND.kernel till 0xA00000
/dev/mtd9 NAND.file-system till end of device
* am335x-evm uses NAND device with block-size=128KiB
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pekon Gupta [Wed, 5 Feb 2014 13:28:30 +0000 (18:58 +0530)]
ARM: OMAP2+: gpmc: update gpmc_hwecc_bch_capable() for new platforms and ECC schemes
This patch
- refactors gpmc_hwecc_bch_capable()
- add checks for new platforms like dra7xx, am43xx
- add checks for OMAP3 SoC, w.r.t. new ECC schemes spawned in following commit:
commit
ac65caf514ec3e55e8d3d510ee37f80dd97418fe
ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NeilBrown [Sat, 1 Mar 2014 13:58:54 +0000 (14:58 +0100)]
ARM: dts: omap3-gta04: Add bma180 accelerometer
Add node for bma180 driver.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NeilBrown [Sat, 1 Mar 2014 13:58:53 +0000 (14:58 +0100)]
ARM: dts: omap3-gta04: Enable mmc2 for wifi
This requires vaux4.
Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NeilBrown [Sat, 1 Mar 2014 13:58:52 +0000 (14:58 +0100)]
ARM: dts: omap3-gta04: Add basic sound support
This adds basic sound support for gta04 board.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NeilBrown [Sat, 1 Mar 2014 13:58:51 +0000 (14:58 +0100)]
ARM: dts: omap3-gta04: Add twl4030 charger
Define twl4030 charger node used for charging.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Belisko [Sat, 1 Mar 2014 13:58:50 +0000 (14:58 +0100)]
ARM: dts: omap3-gta04: Add touchscreen properties
Gta04 using tcs2007 touchscreen. Add support for that.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NeilBrown [Sat, 1 Mar 2014 13:58:49 +0000 (14:58 +0100)]
ARM: dts: omap3-gta04: Add support for magnetometer
Add magnetometer hmc5843 node.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:40 +0000 (18:03 +0530)]
ARM: dts: am437x-gp-evm: Enable gpio.
Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:39 +0000 (18:03 +0530)]
ARM: dts: am437x-gp-evm: Add pwm backlight support.
Add pwm backlight support for gp evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Lokesh Vutla [Thu, 19 Dec 2013 12:33:38 +0000 (18:03 +0530)]
ARM: dts: am437x-gp-evm: Add gp dts.
AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:37 +0000 (18:03 +0530)]
ARM: dts: am43x-epos-evm: Add SPI data.
Add SPI dts data.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:36 +0000 (18:03 +0530)]
ARM: dts: am43x-epos-evm: Add I2C2 data.
Add I2C2 dts data.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Darren Etheridge [Thu, 19 Dec 2013 12:33:35 +0000 (18:03 +0530)]
pinctrl: am43xx: dt-bindings: add MUX_MODE8
AM43xx devices have an extra MUX_MODE for certain pins.
Updating dt include to have MUX_MODE8 which maps to 0x8.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:34 +0000 (18:03 +0530)]
ARM: dts: am43x-epos-evm: Add pwm backlight support.
Add pwm backlight support for am43x epos evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sourav Poddar [Thu, 19 Dec 2013 12:33:33 +0000 (18:03 +0530)]
ARM: dts: am4372: Add pwm-cells property for ecap device.
Add "pwm-cells" node for all ecap, ehrpwm in am43x dtsi files.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sebastian Reichel [Sat, 11 Jan 2014 21:17:03 +0000 (22:17 +0100)]
ARM: dts: OMAP3-N900: Add bq24150a support
This adds support for the bq24150a chip to the
Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sebastian Reichel [Sat, 11 Jan 2014 21:17:02 +0000 (22:17 +0100)]
ARM: dts: OMAP3-N900: Add isp1704 support
This adds support for the isp1704 chip to the Nokia N900
DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sebastian Reichel [Sat, 11 Jan 2014 21:17:01 +0000 (22:17 +0100)]
ARM: dts: OMAP3-N900: Add tpa6130a2 support
This adds support for the N900's headphone
amplifier to the N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sebastian Reichel [Sat, 11 Jan 2014 21:17:00 +0000 (22:17 +0100)]
ARM: dts: OMAP3-N900: Add support for tsl2563
Add support for tsl2563 light sensor to the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sebastian Reichel [Sat, 11 Jan 2014 21:16:59 +0000 (22:16 +0100)]
ARM: dts: OMAP3-N900: Add TWL4030 Keypad Matrix
Add Keyboard Matrix information to N900's DTS file.
This patch maps the keys exactly as the original
board code.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Sebastian Reichel [Sat, 11 Jan 2014 21:16:58 +0000 (22:16 +0100)]
ARM: dts: TWL4030: Add keypad node
Add keypad node to twl4030, so that board DTS
files can just add the keymap.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Nishanth Menon [Mon, 6 Jan 2014 22:37:33 +0000 (16:37 -0600)]
ARM: dts: omap3430-sdp: add dip switch information for MMC operation
MMC 8 bit mode operation depends on dip switch setting which is not
obvious - The current board file has this description. However, with
removal of the board file in the future, this information will be lost
and has to be rediscovered.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Nishanth Menon [Mon, 9 Dec 2013 21:55:50 +0000 (15:55 -0600)]
ARM: dts: Add basic devices for AM3517-craneboard
Craneboard is a hardware development platform based on the Sitara
AM3517 ARM Cortex - A8 microprocessor device - see [1] for more
details. Add basic devices for craneboard as replacement for the board
file scheduled for removal as part of device tree conversion
[1] http://craneboard.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Yegor Yefremov [Fri, 28 Feb 2014 07:19:04 +0000 (08:19 +0100)]
ARM: dts: am335x-evmsk: enable USB1
Enable second USB channel and set it into 'host' mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stefan Roese [Wed, 5 Feb 2014 12:12:39 +0000 (13:12 +0100)]
arm: dts: am33xx.dtsi: Add node name to rtc device node
Making it possible to reference and therefor change (disable) this
device node from other dts file which import this dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Matt Porter [Wed, 29 Jan 2014 20:59:59 +0000 (15:59 -0500)]
ARM: dts: AM33XX: Add ecap interrupt properties
Add missing interrupt properties to the ecap0, ecap1, and ecap2
nodes.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Wed, 29 Jan 2014 18:19:17 +0000 (12:19 -0600)]
ARM: dts: OMAP3+: add clock nodes for CPU
OMAP34xx, AM3517 and OMAP36xx platforms use dpll1 clock.
OMAP443x, OMAP446x, OMAP447x, OMAP5, DRA7, AM43xx platforms use
dpll_mpu clock.
Latency used is the generic latency defined in omap-cpufreq
driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Christoph Fritz [Fri, 14 Feb 2014 14:20:54 +0000 (15:20 +0100)]
ARM: dts: omap3: Add support for INCOstartec DBB056 baseboard
INCOstartec LILLY-DBB056 is a carrier board (baseboard) for
computer-on-module LILLY-A83X.
This patch adds device-tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Christoph Fritz [Fri, 14 Feb 2014 14:20:53 +0000 (15:20 +0100)]
ARM: dts: omap3: Add support for INCOstartec a83x module
INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.
This patch adds device tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:07 +0000 (10:19 +0200)]
ARM: dts: am335x-evmsk: Correct audio clock frequency
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is
24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:06 +0000 (10:19 +0200)]
ARM: dts: omap2: Set disabled status for McBSP instances as default state
In omap2420.dtsi and omap2430.dtsi disable all mcbsp nodes and board dts
files can explicitly enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:05 +0000 (10:19 +0200)]
ARM: dts: omap3: Set disabled status for McBSP instances as default state
In omap3.dtsi disable all mcbsp nodes and board dts files can explicitly
enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:04 +0000 (10:19 +0200)]
ARM: dts: omap5: Set all audio related IP's status to disabled as default
Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:03 +0000 (10:19 +0200)]
ARM: dts: omap4-sdp: No need to disable mcbsp3 node
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:02 +0000 (10:19 +0200)]
ARM: dts: omap4-panda-common: No need to disable the unused audio nodes
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:01 +0000 (10:19 +0200)]
ARM: dts: omap4: Set all audio related IP's status to disabled as default
Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:19:00 +0000 (10:19 +0200)]
ARM: dts: omap4-sdp: Move audio related pinmux to respective nodes
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcbsp2, dmic, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Fri, 24 Jan 2014 08:18:59 +0000 (10:18 +0200)]
ARM: dts: omap4-panda-common: Move audio related pinmux to respective nodes
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Tue, 14 Jan 2014 00:26:47 +0000 (18:26 -0600)]
ARM: dts: AM4372: Add hwspinlock node
Add the hwspinlock device tree node for AM43xx family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Tue, 14 Jan 2014 00:26:46 +0000 (18:26 -0600)]
ARM: dts: DRA7: Add hwspinlock node
Add the hwspinlock device tree node for DRA7 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Tue, 14 Jan 2014 00:26:45 +0000 (18:26 -0600)]
ARM: dts: OMAP: Add #hwlock-cells property to hwspinlock nodes
Add a new generic property "#hwlock-cells" to the hwspinlock
DT nodes on OMAP4, OMAP5 and AM33xx. This common property allows
different platform implementations to define the args specifier
length. OMAP implementations will always use a value of 1.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:55 +0000 (15:22 +0200)]
ARM: OMAP2+: make reset pulse for sbc-t3x usb hubs
sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.
sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.
Add quirks code to handle proper reset pulse signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:54 +0000 (15:22 +0200)]
ARM: dts: sbc-t3517: add support for sbc-t3517
Add support for CM-T3517 CoM and SBC-T3517 board.
reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):
* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led
Added basic support for:
* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:53 +0000 (15:22 +0200)]
ARM: dts: sbc-t3530: add support for sbc-t3530
Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:52 +0000 (15:22 +0200)]
ARM: dts: cm-t3x30: add USB OTG support
Add USB OTG support for cm-t3x30 CoMs.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:51 +0000 (15:22 +0200)]
ARM: dts: sbc-t3730: add pinmux for usb hub reset
GPIO167 is used as SB-T35 baseboard USB Hub reset.
Add GPIO167 pinmux.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:50 +0000 (15:22 +0200)]
ARM: dts: cm-t3x30: add HS USB Host support
Add HS USB Host support along with USB PHYs and power supply regulators
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:49 +0000 (15:22 +0200)]
ARM: dts: cm-t3x30: add twl4030 gpio pullups
Add pullup for twl4030 GPIO_0 used as MMC1 card detect signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:48 +0000 (15:22 +0200)]
ARM: dts: cm-t3x: add gpio-led pinmux
GPIO186 is used for the heartbeat led.
Setup the pinmux for the GPIO186.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:47 +0000 (15:22 +0200)]
ARM: dts: sb-t35: fix Ethernet power supply
SB-T35 baseboard features SMSC9220 Ethernet chip which requires
its own power supply regulators.
Add baseboard specific regulators for the SB-T35 Ethernet chip.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:46 +0000 (15:22 +0200)]
ARM: dts: sbc-t3x: disable mmc3
Disable mmc3 interface, since is not used on sbc-t3x boards.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:45 +0000 (15:22 +0200)]
ARM: dts: sbc-t3x: refactor DT support
Refactor the sbc-t3x device tree as a preparation for additional
(sbc-t3530, sbc-t3517, etc.) boards support.
No functional changes.
The device tree will have the following structure:
omap3-cm-t3x.dtsi
|
|<-- omap3-cm-t3x30.dtsi
| |
| |
| | ----- ------- ------------
| | | CoM | | Board | | Base board |
| | ----- ------- ------------
| | omap3-sb-t35.dtsi
| | |
| |<-- omap3-cm-t3730.dts <-- omap3-sbc-t3730.dts -->|
| | |
| |<-- omap3-cm-t3530.dts <-- omap3-sbc-t3530.dts -->|
| |
|<-------- omap3-cm-t3517.dts <-- omap3-sbc-t3517.dts -->|
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dmitry Lifshitz [Sun, 12 Jan 2014 13:22:44 +0000 (15:22 +0200)]
ARM: dts: sbc-t3x: use omap specific pinctrl defines
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
This simplify further support of CompuLab's boards based on omap36xx,
omap34xx and am35x.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sebastian Reichel [Tue, 21 Jan 2014 14:37:41 +0000 (15:37 +0100)]
ARM: dts: omap3 clocks: simplify ssi aliases
update aliases for the ssi clocks ssi_ssr_fck, ssi_sst_fck and ssi_ick
to make them consistent for omap34xx and omap36xx. This makes it
possible to reference the clocks from generic omap3 dts files.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Markus Pargmann [Thu, 16 Jan 2014 16:08:23 +0000 (17:08 +0100)]
ARM: dts: tps65910 backup battery regulator
This patch adds a devicetree node for the backup battery regulator.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Sun, 16 Feb 2014 21:30:25 +0000 (13:30 -0800)]
Linux 3.14-rc3
Linus Torvalds [Sun, 16 Feb 2014 19:05:27 +0000 (11:05 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We have a small collection of fixes in my for-linus branch.
The big thing that stands out is a revert of a new ioctl. Users
haven't shipped yet in btrfs-progs, and Dave Sterba found a better way
to export the information"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use right clone root offset for compressed extents
btrfs: fix null pointer deference at btrfs_sysfs_add_one+0x105
Btrfs: unset DCACHE_DISCONNECTED when mounting default subvol
Btrfs: fix max_inline mount option
Btrfs: fix a lockdep warning when cleaning up aborted transaction
Revert "btrfs: add ioctl to export size of global metadata reservation"
Linus Torvalds [Sun, 16 Feb 2014 19:03:58 +0000 (11:03 -0800)]
Merge tag 'dt-fixes-for-3.14' of git://git./linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm"
* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: search the best compatible match first in __of_match_node()
Revert "OF: base: match each node compatible against all given matches first"
Kevin Hao [Fri, 14 Feb 2014 05:22:46 +0000 (13:22 +0800)]
of: search the best compatible match first in __of_match_node()
Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.
Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Linus Torvalds [Sun, 16 Feb 2014 00:18:47 +0000 (16:18 -0800)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time to v3.14-rc1 related changes. Also
included is one fix for a free after use regression in persistent
reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix protection copy routine
IB/srpt: replace strict_strtoul() with kstrtoul()
target: Simplify command completion by removing CMD_T_FAILED flag
iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
target: Fix missing length check in spc_emulate_evpd_83()
qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
target: Fix free-after-use regression in PR unregister
Linus Torvalds [Sun, 16 Feb 2014 00:17:51 +0000 (16:17 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"i2c has a bugfix and documentation improvements for you"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Documentation: i2c: mention ACPI method for instantiating devices
Documentation: i2c: describe devicetree method for instantiating devices
i2c: mv64xxx: refactor message start to ensure proper initialization
Linus Torvalds [Sun, 16 Feb 2014 00:06:12 +0000 (16:06 -0800)]
Merge branches 'irq-urgent-for-linus' and 'irq-core-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq update from Thomas Gleixner:
"Fix from the urgent branch: a trivial oneliner adding the missing
Kconfig dependency curing build failures which have been discovered by
several build robots.
The update in the irq-core branch provides a new function in the
irq/devres code, which is a prerequisite for driver developers to get
rid of boilerplate code all over the place.
Not a bugfix, but it has zero impact on the current kernel due to the
lack of users. It's simpler to provide the infrastructure to
interested parties via your tree than fulfilling the wishlist of
driver maintainers on which particular commit or tag this should be
based on"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add missing irq_to_desc export for CONFIG_SPARSE_IRQ=n
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add devm_request_any_context_irq()
Linus Torvalds [Sun, 16 Feb 2014 00:04:42 +0000 (16:04 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"The following trilogy of patches brings you:
- fix for a long standing math overflow issue with HZ < 60
- an onliner fix for a corner case in the dreaded tick broadcast
mechanism affecting a certain range of AMD machines which are
infested with the infamous automagic C1E power control misfeature
- a fix for one of the ARM platforms which allows the kernel to
proceed and boot instead of stupidly panicing for no good reason.
The patch is slightly larger than necessary, but it's less ugly
than the alternative 5 liner"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Clear broadcast pending bit when switching to oneshot
clocksource: Kona: Print warning rather than panic
time: Fix overflow when HZ is smaller than 60
Linus Torvalds [Sat, 15 Feb 2014 23:03:34 +0000 (15:03 -0800)]
Merge tag 'trace-fixes-v3.14-rc2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull twi tracing fixes from Steven Rostedt:
"Two urgent fixes in the tracing utility.
The first is a fix for the way the ring buffer stores timestamps.
After a restructure of the code was done, the ring buffer timestamp
logic missed the fact that the first event on a sub buffer is to have
a zero delta, as the full timestamp is stored on the sub buffer
itself. But because the delta was not cleared to zero, the timestamp
for that event will be calculated as the real timestamp + the delta
from the last timestamp. This can skew the timestamps of the events
and have them say they happened when they didn't really happen.
That's bad.
The second fix is for modifying the function graph caller site. When
the stop machine was removed from updating the function tracing code,
it missed updating the function graph call site location. It is still
modified as if it is being done via stop machine. But it's not. This
can lead to a GPF and kernel crash if the function graph call site
happens to lie between cache lines and one CPU is executing it while
another CPU is doing the update. It would be a very hard condition to
hit, but the result is severe enough to have it fixed ASAP"
* tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Use breakpoints for converting function graph caller
ring-buffer: Fix first commit on sub-buffer having non-zero delta
Linus Torvalds [Sat, 15 Feb 2014 23:02:28 +0000 (15:02 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 EFI fixes from Peter Anvin:
"A few more EFI-related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Check status field to validate BGRT header
x86/efi: Fix 32-bit fallout
Linus Torvalds [Sat, 15 Feb 2014 23:01:33 +0000 (15:01 -0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
Wolfram Sang [Sat, 15 Feb 2014 14:58:35 +0000 (15:58 +0100)]
Documentation: i2c: mention ACPI method for instantiating devices
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Wolfram Sang [Mon, 10 Feb 2014 10:03:55 +0000 (11:03 +0100)]
Documentation: i2c: describe devicetree method for instantiating devices
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Filipe David Borba Manana [Sat, 15 Feb 2014 15:53:16 +0000 (15:53 +0000)]
Btrfs: use right clone root offset for compressed extents
For non compressed extents, iterate_extent_inodes() gives us offsets
that take into account the data offset from the file extent items, while
for compressed extents it doesn't. Therefore we have to adjust them before
placing them in a send clone instruction. Not doing this adjustment leads to
the receiving end requesting for a wrong a file range to the clone ioctl,
which results in different file content from the one in the original send
root.
Issue reproducible with the following excerpt from the test I made for
xfstests:
_scratch_mkfs
_scratch_mount "-o compress-force=lzo"
$XFS_IO_PROG -f -c "truncate 118811" $SCRATCH_MNT/foo
$XFS_IO_PROG -c "pwrite -S 0x0d -b 39987 92267 39987" $SCRATCH_MNT/foo
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap1
$XFS_IO_PROG -c "pwrite -S 0x3e -b 80000 200000 80000" $SCRATCH_MNT/foo
$BTRFS_UTIL_PROG filesystem sync $SCRATCH_MNT
$XFS_IO_PROG -c "pwrite -S 0xdc -b 10000 250000 10000" $SCRATCH_MNT/foo
$XFS_IO_PROG -c "pwrite -S 0xff -b 10000 300000 10000" $SCRATCH_MNT/foo
# will be used for incremental send to be able to issue clone operations
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/clones_snap
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap2
$FSSUM_PROG -A -f -w $tmp/1.fssum $SCRATCH_MNT/mysnap1
$FSSUM_PROG -A -f -w $tmp/2.fssum -x $SCRATCH_MNT/mysnap2/mysnap1 \
-x $SCRATCH_MNT/mysnap2/clones_snap $SCRATCH_MNT/mysnap2
$FSSUM_PROG -A -f -w $tmp/clones.fssum $SCRATCH_MNT/clones_snap \
-x $SCRATCH_MNT/clones_snap/mysnap1 -x $SCRATCH_MNT/clones_snap/mysnap2
$BTRFS_UTIL_PROG send $SCRATCH_MNT/mysnap1 -f $tmp/1.snap
$BTRFS_UTIL_PROG send $SCRATCH_MNT/clones_snap -f $tmp/clones.snap
$BTRFS_UTIL_PROG send -p $SCRATCH_MNT/mysnap1 \
-c $SCRATCH_MNT/clones_snap $SCRATCH_MNT/mysnap2 -f $tmp/2.snap
_scratch_unmount
_scratch_mkfs
_scratch_mount
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/1.snap
$FSSUM_PROG -r $tmp/1.fssum $SCRATCH_MNT/mysnap1 2>> $seqres.full
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/clones.snap
$FSSUM_PROG -r $tmp/clones.fssum $SCRATCH_MNT/clones_snap 2>> $seqres.full
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/2.snap
$FSSUM_PROG -r $tmp/2.fssum $SCRATCH_MNT/mysnap2 2>> $seqres.full
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Anand Jain [Wed, 15 Jan 2014 09:22:28 +0000 (17:22 +0800)]
btrfs: fix null pointer deference at btrfs_sysfs_add_one+0x105
bdev is null when disk has disappeared and mounted with
the degrade option
stack trace
---------
btrfs_sysfs_add_one+0x105/0x1c0 [btrfs]
open_ctree+0x15f3/0x1fe0 [btrfs]
btrfs_mount+0x5db/0x790 [btrfs]
? alloc_pages_current+0xa4/0x160
mount_fs+0x34/0x1b0
vfs_kern_mount+0x62/0xf0
do_mount+0x22e/0xa80
? __get_free_pages+0x9/0x40
? copy_mount_options+0x31/0x170
SyS_mount+0x7e/0xc0
system_call_fastpath+0x16/0x1b
---------
reproducer:
-------
mkfs.btrfs -draid1 -mraid1 /dev/sdc /dev/sdd
(detach a disk)
devmgt detach /dev/sdc [1]
mount -o degrade /dev/sdd /btrfs
-------
[1] github.com/anajain/devmgt.git
Signed-off-by: Anand Jain <Anand.Jain@oracle.com>
Tested-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Wolfram Sang [Thu, 13 Feb 2014 20:36:29 +0000 (21:36 +0100)]
i2c: mv64xxx: refactor message start to ensure proper initialization
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403ae (i2c: mv64xxx: Add I2C Transaction Generator support)
Linus Torvalds [Sat, 15 Feb 2014 00:15:45 +0000 (16:15 -0800)]
Merge tag 'usb-3.14-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.14-rc3. Most of these are xhci
reverts, fixing a bunch of reported issues with USB 3 host controller
issues that loads of people have been hitting (with the exception of
kernel developers, all of our machines seem to be working fine, which
is why these took so long to get resolved...)
There are some other minor fixes and new device ids, as ususal. All
have been in linux-next successfully"
* tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: option: blacklist ZTE MF667 net interface
Revert "usb: xhci: Link TRB must not occur within a USB payload burst"
Revert "xhci: Avoid infinite loop when sg urb requires too many trbs"
Revert "xhci: Set scatter-gather limit to avoid failed block writes."
xhci 1.0: Limit arbitrarily-aligned scatter gather.
Modpost: fixed USB alias generation for ranges including 0x9 and 0xA
usb: core: Fix potential memory leak adding dyn USBdevice IDs
USB: ftdi_sio: add Tagsys RFID Reader IDs
usb: qcserial: add Netgear Aircard 340U
usb-storage: enable multi-LUN scanning when needed
USB: simple: add Dynastream ANT USB-m Stick device support
usb-storage: add unusual-devs entry for BlackBerry 9000
usb-storage: restrict bcdDevice range for Super Top in Cypress ATACB
usb: phy: move some error messages to debug
usb: ftdi_sio: add Mindstorms EV3 console adapter
usb: dwc2: fix memory corruption in dwc2 driver
usb: dwc2: fix role switch breakage
usb: dwc2: bail out early when booting with "nousb"
Revert "xhci: replace xhci_read_64() with readq()"
Revert "xhci: replace xhci_write_64() with writeq()"
...
Linus Torvalds [Sat, 15 Feb 2014 00:15:03 +0000 (16:15 -0800)]
Merge tag 'tty-3.14-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a small number of tty/serial driver fixes to resolve reported
issues with 3.14-rc and earlier (in the case of the vt bugfix). Some
of these have been tested and reported by a number of people as the
tty bugfix was pretty commonly hit on some platforms.
All have been in linux-next for a while"
* tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix secure clear screen
serial: 8250: Support XR17V35x fraction divisor
n_tty: Fix stale echo output
serial: sirf: fix kernel panic caused by unpaired spinlock
serial: 8250_pci: unbreak last serial ports on NetMos 9865 cards
n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0
serial: omap: fix rs485 probe on defered pinctrl
serial: 8250_dw: fix compilation warning when !CONFIG_PM_SLEEP
serial: omap-serial: Move info message to probe function
tty: Set correct tty name in 'active' sysfs attribute
tty: n_gsm: Fix for modems with brk in modem status control
drivers/tty/hvc: don't use module_init in non-modular hyp. console code
Linus Torvalds [Sat, 15 Feb 2014 00:14:11 +0000 (16:14 -0800)]
Merge tag 'staging-3.14-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a number (lots, I know) of fixes for staging drivers to
resolve a bunch of reported issues.
The largest patches here is one revert of a patch that is in 3.14-rc1
to fix reported problems, and a sync of a usb host driver that
required some ARM patches to go in before it could be accepted (which
is why it missed -rc1)
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (56 commits)
staging/rtl8821ae: fix build, depends on MAC80211
iio: max1363: Use devm_regulator_get_optional for optional regulator
iio:accel:bma180: Use modifier instead of index in channel specification
iio: adis16400: Set timestamp as the last element in chan_spec
iio: ak8975: Fix calculation formula for convert micro tesla to gauss unit
staging:iio:ad799x fix typo in ad799x_events[]
iio: mxs-lradc: remove useless scale_available files
iio: mxs-lradc: fix buffer overflow
iio:magnetometer:mag3110: Fix output of decimal digits in show_int_plus_micros()
iio:magnetometer:mag3110: Report busy in _read_raw() / write_raw() when buffer is enabled
wlags49_h2: Fix overflow in wireless_set_essid()
xlr_net: Fix missing trivial allocation check
staging: r8188eu: overflow in rtw_p2p_get_go_device_address()
staging: r8188eu: array overflow in rtw_mp_ioctl_hdl()
staging: r8188eu: Fix typo in USB_DEVICE list
usbip/userspace/libsrc/names.c: memory leak
gpu: ion: dereferencing an ERR_PTR
staging: comedi: usbduxsigma: fix unaligned dereferences
staging: comedi: fix too early cleanup in comedi_auto_config()
staging: android: ion: dummy: fix an error code
...
Linus Torvalds [Sat, 15 Feb 2014 00:13:40 +0000 (16:13 -0800)]
Merge tag 'driver-core-3.14-rc3' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core patch for 3.14-rc3 for the component code
that Russell has found and fixed"
* tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: fix devres handling for master device
Linus Torvalds [Sat, 15 Feb 2014 00:13:00 +0000 (16:13 -0800)]
Merge tag 'char-misc-3.14-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues"
* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "misc: eeprom: sunxi: Add new compatibles"
Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
misc: mic: fix possible signed underflow (undefined behavior) in userspace API
ARM: sunxi: dt: Convert to the new SID compatibles
misc: eeprom: sunxi: Add new compatibles
misc: genwqe: Fix potential memory leak when pinning memory
Documentation:Update Documentation/zh_CN/arm64/memory.txt
Documentation:Update Documentation/zh_CN/arm64/booting.txt
Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
raw: set range for MAX_RAW_DEVS
raw: test against runtime value of max_raw_minors
Drivers: hv: vmbus: Don't timeout during the initial connection with host
Drivers: hv: vmbus: Specify the target CPU that should receive notification
VME: Correct read/write alignment algorithm
mei: don't unset read cb ptr on reset
mei: clear write cb from waiting list on reset
Josef Bacik [Fri, 14 Feb 2014 18:43:48 +0000 (13:43 -0500)]
Btrfs: unset DCACHE_DISCONNECTED when mounting default subvol
A user was running into errors from an NFS export of a subvolume that had a
default subvol set. When we mount a default subvol we will use d_obtain_alias()
to find an existing dentry for the subvolume in the case that the root subvol
has already been mounted, or a dummy one is allocated in the case that the root
subvol has not already been mounted. This allows us to connect the dentry later
on if we wander into the path. However if we don't ever wander into the path we
will keep DCACHE_DISCONNECTED set for a long time, which angers NFS. It doesn't
appear to cause any problems but it is annoying nonetheless, so simply unset
DCACHE_DISCONNECTED in the get_default_root case and switch btrfs_lookup() to
use d_materialise_unique() instead which will make everything play nicely
together and reconnect stuff if we wander into the defaul subvol path from a
different way. With this patch I'm no longer getting the NFS errors when
exporting a volume that has been mounted with a default subvol set. Thanks,
cc: bfields@fieldses.org
cc: ebiederm@xmission.com
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Chris Mason <clm@fb.com>
projects / firefly-linux-kernel-4.4.55.git / log