Benoît Locher [Mon, 27 Aug 2012 13:02:45 +0000 (15:02 +0200)]
can: mcp251x: avoid repeated frame bug
commit
cab32f39dcc5b35db96497dc0a026b5dea76e4e7 upstream.
The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).
Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.
Signed-off-by: Benoît Locher <Benoit.Locher@skf.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Tue, 19 Jun 2012 15:00:00 +0000 (08:00 -0700)]
hwmon: (twl4030-madc-hwmon) Initialize uninitialized structure elements
commit
73d7c119255615a26070f9d6cdb722a166a29015 upstream.
twl4030_madc_conversion uses do_avg and type structure elements of
twl4030_madc_request. Initialize structure to avoid random operation.
Fix for: Coverity CID 200794 Uninitialized scalar variable.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Hilman [Mon, 17 Sep 2012 21:09:17 +0000 (14:09 -0700)]
drivers/rtc/rtc-twl.c: ensure all interrupts are disabled during probe
commit
8dcebaa9a0ae8a0487f4342f3d56d2cb1c980860 upstream.
On some platforms, bootloaders are known to do some interesting RTC
programming. Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads. In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.
This was discovered when finding bursty I2C traffic every second on
Overo platforms. This I2C overhead was keeping the SoC from hitting
deep power states. The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.
Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.
Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Haifeng [Mon, 17 Sep 2012 21:09:21 +0000 (14:09 -0700)]
mm/page_alloc: fix the page address of higher page's buddy calculation
commit
0ba8f2d59304dfe69b59c034de723ad80f7ab9ac upstream.
The heuristic method for buddy has been introduced since commit
43506fad21ca ("mm/page_alloc.c: simplify calculation of combined index
of adjacent buddy lists"). But the page address of higher page's buddy
was wrongly calculated, which will lead page_is_buddy to fail for ever.
IOW, the heuristic method would be disabled with the wrong page address
of higher page's buddy.
Calculating the page address of higher page's buddy should be based
higher_page with the offset between index of higher page and index of
higher page's buddy.
Signed-off-by: Haifeng Li <omycle@gmail.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: KyongHo Cho <pullip.cho@samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Thu, 16 Aug 2012 06:46:12 +0000 (16:46 +1000)]
md: Don't truncate size at 4TB for RAID0 and Linear
commit
667a5313ecd7308d79629c0738b0db588b0b0a4e upstream.
commit
27a7b260f71439c40546b43588448faac01adb93
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
changed 0.90 metadata handling to truncated size to 4TB as that is
all that 0.90 can record.
However for RAID0 and Linear, 0.90 doesn't need to record the size, so
this truncation is not needed and causes working arrays to become too small.
So avoid the truncation for RAID0 and Linear
This bug was introduced in 3.1 and is suitable for any stable kernels
from then onwards.
As the offending commit was tagged for 'stable', any stable kernel
that it was applied to should also get this patch. That includes
at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for
providing that list).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mel Gorman [Sun, 19 Aug 2012 02:41:03 +0000 (14:41 +1200)]
Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
commit
67a806d9499353fabd5b5ff07337f3aa88a1c3ba upstream.
The following build error occurred during an alpha build:
net/core/sock.c:274:36: error: initializer element is not constant
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Sun, 2 Sep 2012 13:41:34 +0000 (15:41 +0200)]
kobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"
commit
60e233a56609fd963c59e99bd75c663d63fa91b6 upstream.
Fengguang Wu <fengguang.wu@intel.com> writes:
> After the __devinit* removal series, I can still get kernel panic in
> show_uevent(). So there are more sources of bug..
>
> Debug patch:
>
> @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device
> goto out;
>
> /* copy keys to file */
> - for (i = 0; i < env->envp_idx; i++)
> + dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name);
> + for (i = 0; i < env->envp_idx; i++) {
> + printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]);
> count += sprintf(&buf[count], "%s\n", env->envp[i]);
> + }
>
> Oops message, the env[] is again not properly initilized:
>
> [ 44.068623] input input0: uevent 61 env[
805306368]: input0/.../input0
> [ 44.069552] uevent 0 env[0]: (null)
This is a completely different CONFIG_HOTPLUG problem, only
demonstrating another reason why CONFIG_HOTPLUG should go away. I had a
hard time trying to disable it anyway ;-)
The problem this time is lots of code assuming that a call to
add_uevent_var() will guarantee that env->buflen > 0. This is not true
if CONFIG_HOTPLUG is unset. So things like this end up overwriting
env->envp_idx because the array index is -1:
if (add_uevent_var(env, "MODALIAS="))
return -ENOMEM;
len = input_print_modalias(&env->buf[env->buflen - 1],
sizeof(env->buf) - env->buflen,
dev, 0);
Don't know what the best action is, given that there seem to be a *lot*
of this around the kernel. This patch "fixes" the problem for me, but I
don't know if it can be considered an appropriate fix.
[ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to
always be on is the longterm fix, but it's too late for 3.6 and older
kernels to resolve this that way - gregkh ]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Tue, 4 Sep 2012 15:07:18 +0000 (16:07 +0100)]
ahci: Add alternate identifier for the 88SE9172
commit
17c60c6b763cb5b83b0185e7d38d01d18e55a05a upstream.
This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shawn Guo [Wed, 22 Aug 2012 15:10:01 +0000 (23:10 +0800)]
mmc: sdhci-esdhc: break out early if clock is 0
commit
74f330bceaa7b88d06062e1cac3d519a3dfc041e upstream.
Since commit
30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lauri Hintsala [Tue, 17 Jul 2012 14:16:09 +0000 (17:16 +0300)]
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
commit
1af36b2a993dddfa3d6860ec4879c9e8abc9b976 upstream.
Release the lock before mmc_signal_sdio_irq is called by mxs_mmc_irq_handler.
Backtrace:
[ 79.660000] =============================================
[ 79.660000] [ INFO: possible recursive locking detected ]
[ 79.660000]
3.4.0-00009-g3e96082-dirty #11 Not tainted
[ 79.660000] ---------------------------------------------
[ 79.660000] swapper/0 is trying to acquire lock:
[ 79.660000] (&(&host->lock)->rlock#2){-.....}, at: [<
c026ea3c>] mxs_mmc_enable_sdio_irq+0x18/0xd4
[ 79.660000]
[ 79.660000] but task is already holding lock:
[ 79.660000] (&(&host->lock)->rlock#2){-.....}, at: [<
c026f744>] mxs_mmc_irq_handler+0x1c/0xe8
[ 79.660000]
[ 79.660000] other info that might help us debug this:
[ 79.660000] Possible unsafe locking scenario:
[ 79.660000]
[ 79.660000] CPU0
[ 79.660000] ----
[ 79.660000] lock(&(&host->lock)->rlock#2);
[ 79.660000] lock(&(&host->lock)->rlock#2);
[ 79.660000]
[ 79.660000] *** DEADLOCK ***
[ 79.660000]
[ 79.660000] May be due to missing lock nesting notation
[ 79.660000]
[ 79.660000] 1 lock held by swapper/0:
[ 79.660000] #0: (&(&host->lock)->rlock#2){-.....}, at: [<
c026f744>] mxs_mmc_irq_handler+0x1c/0xe8
[ 79.660000]
[ 79.660000] stack backtrace:
[ 79.660000] [<
c0014bd0>] (unwind_backtrace+0x0/0xf4) from [<
c005f9c0>] (__lock_acquire+0x1948/0x1d48)
[ 79.660000] [<
c005f9c0>] (__lock_acquire+0x1948/0x1d48) from [<
c005fea0>] (lock_acquire+0xe0/0xf8)
[ 79.660000] [<
c005fea0>] (lock_acquire+0xe0/0xf8) from [<
c03a8460>] (_raw_spin_lock_irqsave+0x44/0x58)
[ 79.660000] [<
c03a8460>] (_raw_spin_lock_irqsave+0x44/0x58) from [<
c026ea3c>] (mxs_mmc_enable_sdio_irq+0x18/0xd4)
[ 79.660000] [<
c026ea3c>] (mxs_mmc_enable_sdio_irq+0x18/0xd4) from [<
c026f7fc>] (mxs_mmc_irq_handler+0xd4/0xe8)
[ 79.660000] [<
c026f7fc>] (mxs_mmc_irq_handler+0xd4/0xe8) from [<
c006bdd8>] (handle_irq_event_percpu+0x70/0x254)
[ 79.660000] [<
c006bdd8>] (handle_irq_event_percpu+0x70/0x254) from [<
c006bff8>] (handle_irq_event+0x3c/0x5c)
[ 79.660000] [<
c006bff8>] (handle_irq_event+0x3c/0x5c) from [<
c006e6d0>] (handle_level_irq+0x90/0x110)
[ 79.660000] [<
c006e6d0>] (handle_level_irq+0x90/0x110) from [<
c006b930>] (generic_handle_irq+0x38/0x50)
[ 79.660000] [<
c006b930>] (generic_handle_irq+0x38/0x50) from [<
c00102fc>] (handle_IRQ+0x30/0x84)
[ 79.660000] [<
c00102fc>] (handle_IRQ+0x30/0x84) from [<
c000f058>] (__irq_svc+0x38/0x60)
[ 79.660000] [<
c000f058>] (__irq_svc+0x38/0x60) from [<
c0010520>] (default_idle+0x2c/0x40)
[ 79.660000] [<
c0010520>] (default_idle+0x2c/0x40) from [<
c0010a90>] (cpu_idle+0x64/0xcc)
[ 79.660000] [<
c0010a90>] (cpu_idle+0x64/0xcc) from [<
c04ff858>] (start_kernel+0x244/0x2c8)
[ 79.660000] BUG: spinlock lockup on CPU#0, swapper/0
[ 79.660000] lock:
c398cb2c, .magic:
dead4ead, .owner: swapper/0, .owner_cpu: 0
[ 79.660000] [<
c0014bd0>] (unwind_backtrace+0x0/0xf4) from [<
c01ddb1c>] (do_raw_spin_lock+0xf0/0x144)
[ 79.660000] [<
c01ddb1c>] (do_raw_spin_lock+0xf0/0x144) from [<
c03a8468>] (_raw_spin_lock_irqsave+0x4c/0x58)
[ 79.660000] [<
c03a8468>] (_raw_spin_lock_irqsave+0x4c/0x58) from [<
c026ea3c>] (mxs_mmc_enable_sdio_irq+0x18/0xd4)
[ 79.660000] [<
c026ea3c>] (mxs_mmc_enable_sdio_irq+0x18/0xd4) from [<
c026f7fc>] (mxs_mmc_irq_handler+0xd4/0xe8)
[ 79.660000] [<
c026f7fc>] (mxs_mmc_irq_handler+0xd4/0xe8) from [<
c006bdd8>] (handle_irq_event_percpu+0x70/0x254)
[ 79.660000] [<
c006bdd8>] (handle_irq_event_percpu+0x70/0x254) from [<
c006bff8>] (handle_irq_event+0x3c/0x5c)
[ 79.660000] [<
c006bff8>] (handle_irq_event+0x3c/0x5c) from [<
c006e6d0>] (handle_level_irq+0x90/0x110)
[ 79.660000] [<
c006e6d0>] (handle_level_irq+0x90/0x110) from [<
c006b930>] (generic_handle_irq+0x38/0x50)
[ 79.660000] [<
c006b930>] (generic_handle_irq+0x38/0x50) from [<
c00102fc>] (handle_IRQ+0x30/0x84)
[ 79.660000] [<
c00102fc>] (handle_IRQ+0x30/0x84) from [<
c000f058>] (__irq_svc+0x38/0x60)
[ 79.660000] [<
c000f058>] (__irq_svc+0x38/0x60) from [<
c0010520>] (default_idle+0x2c/0x40)
[ 79.660000] [<
c0010520>] (default_idle+0x2c/0x40) from [<
c0010a90>] (cpu_idle+0x64/0xcc)
[ 79.660000] [<
c0010a90>] (cpu_idle+0x64/0xcc) from [<
c04ff858>] (start_kernel+0x244/0x2c8)
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Mon, 20 Aug 2012 13:59:25 +0000 (14:59 +0100)]
perf_event: Switch to internal refcount, fix race with close()
commit
a6fa941d94b411bbd2b6421ffbde6db3c93e65ab upstream.
Don't mess with file refcounts (or keep a reference to file, for
that matter) in perf_event. Use explicit refcount of its own
instead. Deal with the race between the final reference to event
going away and new children getting created for it by use of
atomic_long_inc_not_zero() in inherit_event(); just have the
latter free what it had allocated and return NULL, that works
out just fine (children of siblings of something doomed are
created as singletons, same as if the child of leader had been
created and immediately killed).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120820135925.GG23464@ZenIV.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Tue, 11 Sep 2012 07:40:31 +0000 (09:40 +0200)]
USB: option: replace ZTE K5006-Z entry with vendor class rule
commit
ba9edaa468869a8cea242a411066b0f490751798 upstream.
Fix the ZTE K5006-Z entry so that it actually matches anything
commit
f1b5c997 USB: option: add ZTE K5006-Z
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1018 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821Vxxxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=86 Prot=10 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=05 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=00 Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 31 Aug 2012 19:41:30 +0000 (20:41 +0100)]
staging: comedi: das08: Correct AO output for das08jr-16-ao
commit
61ed59ed09e6ad2b8395178ea5ad5f653bba08e3 upstream.
Don't zero out bits 15..12 of the data value in `das08jr_ao_winsn()` as
that knobbles the upper three-quarters of the output range for the
'das08jr-16-ao' board.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Mon, 10 Sep 2012 19:22:11 +0000 (21:22 +0200)]
staging: r8712u: fix bug in r8712_recv_indicatepkt()
commit
abf02cfc179bb4bd30d05f582d61b3b8f429b813 upstream.
64bit arches have a buggy r8712u driver, let's fix it.
skb->tail must be set properly or network stack behavior is undefined.
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=847525
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=45071
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Jones <davej@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Wed, 29 Aug 2012 22:08:21 +0000 (23:08 +0100)]
staging: vt6656: [BUG] - Failed connection, incorrect endian.
commit
aa209eef3ce8419ff2926c2fa944dfbfb5afbacb upstream.
Hi,
This patch fixes a bug with driver failing to negotiate a connection.
The bug was traced to commit
203e4615ee9d9fa8d3506b9d0ef30095e4d5bc90
staging: vt6656: removed custom definitions of Ethernet packet types
In that patch, definitions in include/linux/if_ether.h replaced ones
in tether.h which had both big and little endian definitions.
include/linux/if_ether.h only refers to big endian values, cpu_to_be16
should be used for the correct endian architectures.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christopher Brannon [Sat, 16 Jun 2012 21:55:20 +0000 (16:55 -0500)]
Staging: speakup: fix an improperly-declared variable.
commit
4ea418b8b2fa8a70d0fcc8231b65e67b3a72984b upstream.
A local static variable was declared as a pointer to a string
constant. We're assigning to the underlying memory, so it
needs to be an array instead.
Signed-off-by: Christopher Brannon <chris@the-brannons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matteo Frigo [Wed, 12 Sep 2012 14:12:06 +0000 (10:12 -0400)]
ALSA: ice1724: Use linear scale for AK4396 volume control.
commit
3737e2be505d872bf2b3c1cd4151b2d2b413d7b5 upstream.
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
Signed-off-by: Matteo Frigo <athena@fftw.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Bellinger [Thu, 16 Aug 2012 22:33:10 +0000 (15:33 -0700)]
target: Fix ->data_length re-assignment bug with SCSI overflow
commit
4c054ba63ad47ef244cfcfa1cea38134620a5bae upstream.
This patch fixes a long-standing bug with SCSI overflow handling
where se_cmd->data_length was incorrectly being re-assigned to
the larger CDB extracted allocation length, resulting in a number
of fabric level errors that would end up causing a session reset
in most cases. So instead now:
- Only re-assign se_cmd->data_length durining UNDERFLOW (to use the
smaller value)
- Use existing se_cmd->data_length for OVERFLOW (to use the smaller
value)
This fix has been tested with the following CDB to generate an
SCSI overflow:
sg_raw -r512 /dev/sdc 28 0 0 0 0 0 0 0 9 0
Tested using iscsi-target, tcm_qla2xxx, loopback and tcm_vhost fabric
ports. Here is a bit more detail on each case:
- iscsi-target: Bug with open-iscsi with overflow, sg_raw returns
-3584 bytes of data.
- tcm_qla2xxx: Working as expected, returnins 512 bytes of data
- loopback: sg_raw returns CHECK_CONDITION, from overflow rejection
in transport_generic_map_mem_to_cmd()
- tcm_vhost: Same as loopback
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tyler Hicks [Thu, 13 Sep 2012 19:00:56 +0000 (12:00 -0700)]
eCryptfs: Copy up attributes of the lower target inode after rename
commit
8335eafc2859e1a26282bef7c3d19f3d68868b8a upstream.
After calling into the lower filesystem to do a rename, the lower target
inode's attributes were not copied up to the eCryptfs target inode. This
resulted in the eCryptfs target inode staying around, rather than being
evicted, because i_nlink was not updated for the eCryptfs inode. This
also meant that eCryptfs didn't do the final iput() on the lower target
inode so it stayed around, as well. This would result in a failure to
free up space occupied by the target file in the rename() operation.
Both target inodes would eventually be evicted when the eCryptfs
filesystem was unmounted.
This patch calls fsstack_copy_attr_all() after the lower filesystem
does its ->rename() so that important inode attributes, such as i_nlink,
are updated at the eCryptfs layer. ecryptfs_evict_inode() is now called
and eCryptfs can drop its final reference on the lower inode.
http://launchpad.net/bugs/561129
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amerigo Wang [Sat, 18 Aug 2012 07:02:20 +0000 (07:02 +0000)]
netconsole: remove a redundant netconsole_target_put()
commit
72d3eb13b5c0abe7d63efac41f39c5b644c7bbaa upstream.
This netconsole_target_put() is obviously redundant, and it
causes a kernel segfault when removing a bridge device which has
netconsole running on it.
This is caused by:
commit
8d8fc29d02a33e4bd5f4fa47823c1fd386346093
Author: Amerigo Wang <amwang@redhat.com>
Date: Thu May 19 21:39:10 2011 +0000
netpoll: disable netpoll when enslave a device
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Mon, 17 Sep 2012 20:31:38 +0000 (22:31 +0200)]
vfs: dcache: use DCACHE_DENTRY_KILLED instead of DCACHE_DISCONNECTED in d_kill()
commit
b161dfa6937ae46d50adce8a7c6b12233e96e7bd upstream.
IBM reported a soft lockup after applying the fix for the rename_lock
deadlock. Commit
c83ce989cb5f ("VFS: Fix the nfs sillyrename regression
in kernel 2.6.38") was found to be the culprit.
The nfs sillyrename fix used DCACHE_DISCONNECTED to indicate that the
dentry was killed. This flag can be set on non-killed dentries too,
which results in infinite retries when trying to traverse the dentry
tree.
This patch introduces a separate flag: DCACHE_DENTRY_KILLED, which is
only set in d_kill() and makes try_to_ascend() test only this flag.
IBM reported successful test results with this patch.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 14 Sep 2012 21:48:21 +0000 (14:48 -0700)]
vfs: make O_PATH file descriptors usable for 'fstat()'
commit
55815f70147dcfa3ead5738fd56d3574e2e3c1c2 upstream.
We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors. This should make it more
directly comparable to the O_SEARCH of Solaris.
Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.
See also commit
332a2e1244bd, which did the same thing for fchdir, for
the same reasons.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen M. Cameron [Fri, 14 Sep 2012 21:35:10 +0000 (16:35 -0500)]
cciss: fix handling of protocol error
commit
2453f5f992717251cfadab6184fbb3ec2f2e8b40 upstream.
If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor. Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Tue, 18 Sep 2012 21:24:59 +0000 (14:24 -0700)]
cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU
commit
6889125b8b4e09c5e53e6ecab3433bed1ce198c9 upstream.
powernowk8_target() runs off a per-cpu work item and if the
cpufreq_policy->cpu is different from the current one, it migrates the
kworker to the target CPU by manipulating current->cpus_allowed. The
function migrates the kworker back to the original CPU but this is
still broken. Workqueue concurrency management requires the kworkers
to stay on the same CPU and powernowk8_target() ends up triggerring
BUG_ON(rq != this_rq()) in try_to_wake_up_local() if it contends on
fidvid_mutex and sleeps.
It is unclear why this bug is being reported now. Duncan says it
appeared to be a regression of 3.6-rc1 and couldn't reproduce it on
3.5. Bisection seemed to point to
63d95a91 "workqueue: use @pool
instead of @gcwq or @cpu where applicable" which is an non-functional
change. Given that the reproduce case sometimes took upto days to
trigger, it's easy to be misled while bisecting. Maybe something made
contention on fidvid_mutex more likely? I don't know.
This patch fixes the bug by using work_on_cpu() instead if @pol->cpu
isn't the same as the current one. The code assumes that
cpufreq_policy->cpu is kept online by the caller, which Rafael tells
me is the case.
stable:
ed48ece27c ("workqueue: reimplement work_on_cpu() using
system_wq") should be applied before this; otherwise, the
behavior could be horrible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47301
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Tue, 18 Sep 2012 19:48:43 +0000 (12:48 -0700)]
workqueue: reimplement work_on_cpu() using system_wq
commit
ed48ece27cd3d5ee0354c32bbaec0f3e1d4715c3 upstream.
The existing work_on_cpu() implementation is hugely inefficient. It
creates a new kthread, execute that single function and then let the
kthread die on each invocation.
Now that system_wq can handle concurrent executions, there's no
advantage of doing this. Reimplement work_on_cpu() using system_wq
which makes it simpler and way more efficient.
stable: While this isn't a fix in itself, it's needed to fix a
workqueue related bug in cpufreq/powernow-k8. AFAICS, this
shouldn't break other existing users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Francesco Ruggeri [Fri, 24 Aug 2012 07:38:35 +0000 (07:38 +0000)]
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
[ Upstream commit
acbb219d5f53821b2d0080d047800410c0420ea1 ]
When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.
Tested in Linux 3.4.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xeb@mail.ru [Fri, 24 Aug 2012 01:07:38 +0000 (01:07 +0000)]
l2tp: avoid to use synchronize_rcu in tunnel free function
[ Upstream commit
99469c32f79a32d8481f87be0d3c66dad286f4ec ]
Avoid to use synchronize_rcu in l2tp_tunnel_free because context may be
atomic.
Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Thu, 23 Aug 2012 02:09:11 +0000 (02:09 +0000)]
netlink: fix possible spoofing from non-root processes
[ Upstream commit
20e1db19db5d6b9e4e83021595eab0dc8f107bef ]
Non-root user-space processes can send Netlink messages to other
processes that are well-known for being subscribed to Netlink
asynchronous notifications. This allows ilegitimate non-root
process to send forged messages to Netlink subscribers.
The userspace process usually verifies the legitimate origin in
two ways:
a) Socket credentials. If UID != 0, then the message comes from
some ilegitimate process and the message needs to be dropped.
b) Netlink portID. In general, portID == 0 means that the origin
of the messages comes from the kernel. Thus, discarding any
message not coming from the kernel.
However, ctnetlink sets the portID in event messages that has
been triggered by some user-space process, eg. conntrack utility.
So other processes subscribed to ctnetlink events, eg. conntrackd,
know that the event was triggered by some user-space action.
Neither of the two ways to discard ilegitimate messages coming
from non-root processes can help for ctnetlink.
This patch adds capability validation in case that dst_pid is set
in netlink_sendmsg(). This approach is aggressive since existing
applications using any Netlink bus to deliver messages between
two user-space processes will break. Note that the exception is
NETLINK_USERSOCK, since it is reserved for netlink-to-netlink
userspace communication.
Still, if anyone wants that his Netlink bus allows netlink-to-netlink
userspace, then they can set NL_NONROOT_SEND. However, by default,
I don't think it makes sense to allow to use NETLINK_ROUTE to
communicate two processes that are sending no matter what information
that is not related to link/neighbouring/routing. They should be using
NETLINK_USERSOCK instead for that.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:57 +0000 (11:31 +0000)]
net: fix info leak in compat dev_ifconf()
[ Upstream commit
43da5f2e0d0c69ded3d51907d9552310a6b545e8 ]
The implementation of dev_ifconf() for the compat ioctl interface uses
an intermediate ifc structure allocated in userland for the duration of
the syscall. Though, it fails to initialize the padding bytes inserted
for alignment and that for leaks four bytes of kernel stack. Add an
explicit memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:56 +0000 (11:31 +0000)]
ipvs: fix info leak in getsockopt(IP_VS_SO_GET_TIMEOUT)
[ Upstream commit
2d8a041b7bfe1097af21441cb77d6af95f4f4680 ]
If at least one of CONFIG_IP_VS_PROTO_TCP or CONFIG_IP_VS_PROTO_UDP is
not set, __ip_vs_get_timeouts() does not fully initialize the structure
that gets copied to userland and that for leaks up to 12 bytes of kernel
stack. Add an explicit memset(0) before passing the structure to
__ip_vs_get_timeouts() to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: Simon Horman <horms@verge.net.au>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:55 +0000 (11:31 +0000)]
dccp: fix info leak via getsockopt(DCCP_SOCKOPT_CCID_TX_INFO)
[ Upstream commit
7b07f8eb75aa3097cdfd4f6eac3da49db787381d ]
The CCID3 code fails to initialize the trailing padding bytes of struct
tfrc_tx_info added for alignment on 64 bit architectures. It that for
potentially leaks four bytes kernel stack via the getsockopt() syscall.
Add an explicit memset(0) before filling the structure to avoid the
info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:53 +0000 (11:31 +0000)]
llc: fix info leak via getsockname()
[ Upstream commit
3592aaeb80290bda0f2cf0b5456c97bfc638b192 ]
The LLC code wrongly returns 0, i.e. "success", when the socket is
zapped. Together with the uninitialized uaddrlen pointer argument from
sys_getsockname this leads to an arbitrary memory leak of up to 128
bytes kernel stack via the getsockname() syscall.
Return an error instead when the socket is zapped to prevent the info
leak. Also remove the unnecessary memset(0). We don't directly write to
the memory pointed by uaddr but memcpy() a local structure at the end of
the function that is properly initialized.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:51 +0000 (11:31 +0000)]
Bluetooth: L2CAP - Fix info leak via getsockname()
[ Upstream commit
792039c73cf176c8e39a6e8beef2c94ff46522ed ]
The L2CAP code fails to initialize the l2_bdaddr_type member of struct
sockaddr_l2 and the padding byte added for alignment. It that for leaks
two bytes kernel stack via the getsockname() syscall. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:50 +0000 (11:31 +0000)]
Bluetooth: RFCOMM - Fix info leak via getsockname()
[ Upstream commit
9344a972961d1a6d2c04d9008b13617bcb6ec2ef ]
The RFCOMM code fails to initialize the trailing padding byte of struct
sockaddr_rc added for alignment. It that for leaks one byte kernel stack
via the getsockname() syscall. Add an explicit memset(0) before filling
the structure to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:49 +0000 (11:31 +0000)]
Bluetooth: RFCOMM - Fix info leak in ioctl(RFCOMMGETDEVLIST)
[ Upstream commit
f9432c5ec8b1e9a09b9b0e5569e3c73db8de432a ]
The RFCOMM code fails to initialize the two padding bytes of struct
rfcomm_dev_list_req inserted for alignment before copying it to
userland. Additionally there are two padding bytes in each instance of
struct rfcomm_dev_info. The ioctl() that for disclosures two bytes plus
dev_num times two bytes uninitialized kernel heap memory.
Allocate the memory using kzalloc() to fix this issue.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:47 +0000 (11:31 +0000)]
Bluetooth: HCI - Fix info leak via getsockname()
[ Upstream commit
3f68ba07b1da811bf383b4b701b129bfcb2e4988 ]
The HCI code fails to initialize the hci_channel member of struct
sockaddr_hci and that for leaks two bytes kernel stack via the
getsockname() syscall. Initialize hci_channel with 0 to avoid the
info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:46 +0000 (11:31 +0000)]
Bluetooth: HCI - Fix info leak in getsockopt(HCI_FILTER)
[ Upstream commit
e15ca9a0ef9a86f0477530b0f44a725d67f889ee ]
The HCI code fails to initialize the two padding bytes of struct
hci_ufilter before copying it to userland -- that for leaking two
bytes kernel stack. Add an explicit memset(0) before filling the
structure to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:45 +0000 (11:31 +0000)]
atm: fix info leak via getsockname()
[ Upstream commit
3c0c5cfdcd4d69ffc4b9c0907cec99039f30a50a ]
The ATM code fails to initialize the two padding bytes of struct
sockaddr_atmpvc inserted for alignment. Add an explicit memset(0)
before filling the structure to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:44 +0000 (11:31 +0000)]
atm: fix info leak in getsockopt(SO_ATMPVC)
[ Upstream commit
e862f1a9b7df4e8196ebec45ac62295138aa3fc2 ]
The ATM code fails to initialize the two padding bytes of struct
sockaddr_atmpvc inserted for alignment. Add an explicit memset(0)
before filling the structure to avoid the info leak.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Tue, 14 Aug 2012 08:54:51 +0000 (08:54 +0000)]
ipv6: addrconf: Avoid calling netdevice notifiers with RCU read-side lock
[ Upstream commit
4acd4945cd1e1f92b20d14e349c6c6a52acbd42d ]
Cong Wang reports that lockdep detected suspicious RCU usage while
enabling IPV6 forwarding:
[ 1123.310275] ===============================
[ 1123.442202] [ INFO: suspicious RCU usage. ]
[ 1123.558207] 3.6.0-rc1+ #109 Not tainted
[ 1123.665204] -------------------------------
[ 1123.768254] include/linux/rcupdate.h:430 Illegal context switch in RCU read-side critical section!
[ 1123.992320]
[ 1123.992320] other info that might help us debug this:
[ 1123.992320]
[ 1124.307382]
[ 1124.307382] rcu_scheduler_active = 1, debug_locks = 0
[ 1124.522220] 2 locks held by sysctl/5710:
[ 1124.648364] #0: (rtnl_mutex){+.+.+.}, at: [<
ffffffff81768498>] rtnl_trylock+0x15/0x17
[ 1124.882211] #1: (rcu_read_lock){.+.+.+}, at: [<
ffffffff81871df8>] rcu_lock_acquire+0x0/0x29
[ 1125.085209]
[ 1125.085209] stack backtrace:
[ 1125.332213] Pid: 5710, comm: sysctl Not tainted 3.6.0-rc1+ #109
[ 1125.441291] Call Trace:
[ 1125.545281] [<
ffffffff8109d915>] lockdep_rcu_suspicious+0x109/0x112
[ 1125.667212] [<
ffffffff8107c240>] rcu_preempt_sleep_check+0x45/0x47
[ 1125.781838] [<
ffffffff8107c260>] __might_sleep+0x1e/0x19b
[...]
[ 1127.445223] [<
ffffffff81757ac5>] call_netdevice_notifiers+0x4a/0x4f
[...]
[ 1127.772188] [<
ffffffff8175e125>] dev_disable_lro+0x32/0x6b
[ 1127.885174] [<
ffffffff81872d26>] dev_forward_change+0x30/0xcb
[ 1128.013214] [<
ffffffff818738c4>] addrconf_forward_change+0x85/0xc5
[...]
addrconf_forward_change() uses RCU iteration over the netdev list,
which is unnecessary since it already holds the RTNL lock. We also
cannot reasonably require netdevice notifier functions not to sleep.
Reported-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
danborkmann@iogearbox.net [Fri, 10 Aug 2012 22:48:54 +0000 (22:48 +0000)]
af_packet: remove BUG statement in tpacket_destruct_skb
[ Upstream commit
7f5c3e3a80e6654cf48dfba7cf94f88c6b505467 ]
Here's a quote of the comment about the BUG macro from asm-generic/bug.h:
Don't use BUG() or BUG_ON() unless there's really no way out; one
example might be detecting data structure corruption in the middle
of an operation that can't be backed out of. If the (sub)system
can somehow continue operating, perhaps with reduced functionality,
it's probably not BUG-worthy.
If you're tempted to BUG(), think again: is completely giving up
really the *only* solution? There are usually better options, where
users don't need to reboot ASAP and can mostly shut down cleanly.
In our case, the status flag of a ring buffer slot is managed from both sides,
the kernel space and the user space. This means that even though the kernel
side might work as expected, the user space screws up and changes this flag
right between the send(2) is triggered when the flag is changed to
TP_STATUS_SENDING and a given skb is destructed after some time. Then, this
will hit the BUG macro. As David suggested, the best solution is to simply
remove this statement since it cannot be used for kernel side internal
consistency checks. I've tested it and the system still behaves /stable/ in
this case, so in accordance with the above comment, we should rather remove it.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Khoroshilov [Wed, 8 Aug 2012 00:33:25 +0000 (00:33 +0000)]
net/core: Fix potential memory leak in dev_set_alias()
[ Upstream commit
7364e445f62825758fa61195d237a5b8ecdd06ec ]
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wu Fengguang [Thu, 2 Aug 2012 23:10:01 +0000 (23:10 +0000)]
isdnloop: fix and simplify isdnloop_init()
[ Upstream commit
77f00f6324cb97cf1df6f9c4aaeea6ada23abdb2 ]
Fix a buffer overflow bug by removing the revision and printk.
[ 22.016214] isdnloop-ISDN-driver Rev 1.11.6.7
[ 22.097508] isdnloop: (loop0) virtual card added
[ 22.174400] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in:
ffffffff83244972
[ 22.174400]
[ 22.436157] Pid: 1, comm: swapper Not tainted
3.5.0-bisect-00018-gfa8bbb1-dirty #129
[ 22.624071] Call Trace:
[ 22.720558] [<
ffffffff832448c3>] ? CallcNew+0x56/0x56
[ 22.815248] [<
ffffffff8222b623>] panic+0x110/0x329
[ 22.914330] [<
ffffffff83244972>] ? isdnloop_init+0xaf/0xb1
[ 23.014800] [<
ffffffff832448c3>] ? CallcNew+0x56/0x56
[ 23.090763] [<
ffffffff8108e24b>] __stack_chk_fail+0x2b/0x30
[ 23.185748] [<
ffffffff83244972>] isdnloop_init+0xaf/0xb1
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiroaki SHIMODA [Fri, 3 Aug 2012 10:57:52 +0000 (19:57 +0900)]
net_sched: gact: Fix potential panic in tcf_gact().
[ Upstream commit
696ecdc10622d86541f2e35cc16e15b6b3b1b67e ]
gact_rand array is accessed by gact->tcfg_ptype whose value
is assumed to less than MAX_RAND, but any range checks are
not performed.
So add a check in tcf_gact_init(). And in tcf_gact(), we can
reduce a branch.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 30 Jul 2012 16:11:42 +0000 (16:11 +0000)]
tcp: Apply device TSO segment limit earlier
[ Upstream commit
1485348d2424e1131ea42efc033cbd9366462b01 ]
Cache the device gso_max_segs in sock::sk_gso_max_segs and use it to
limit the size of TSO skbs. This avoids the need to fall back to
software GSO for local TCP senders.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 30 Jul 2012 15:57:44 +0000 (15:57 +0000)]
sfc: Fix maximum number of TSO segments and minimum TX queue size
[ Upstream commit
7e6d06f0de3f74ca929441add094518ae332257c ]
Currently an skb requiring TSO may not fit within a minimum-size TX
queue. The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset). This issue is designated as CVE-2012-3412.
Set the maximum number of TSO segments for our devices to 100. This
should make no difference to behaviour unless the actual MSS is less
than about 700. Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.
To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 30 Jul 2012 15:57:00 +0000 (15:57 +0000)]
net: Allow driver to limit number of GSO segments per skb
[ Upstream commit
30b678d844af3305cda5953467005cebb5d7b687 ]
A peer (or local user) may cause TCP to use a nominal MSS of as little
as 88 (actual MSS of 76 with timestamps). Given that we have a
sufficiently prodigious local sender and the peer ACKs quickly enough,
it is nevertheless possible to grow the window for such a connection
to the point that we will try to send just under 64K at once. This
results in a single skb that expands to 861 segments.
In some drivers with TSO support, such an skb will require hundreds of
DMA descriptors; a substantial fraction of a TX ring or even more than
a full ring. The TX queue selected for the skb may stall and trigger
the TX watchdog repeatedly (since the problem skb will be retried
after the TX reset). This particularly affects sfc, for which the
issue is designated as CVE-2012-3412.
Therefore:
1. Add the field net_device::gso_max_segs holding the device-specific
limit.
2. In netif_skb_features(), if the number of segments is too high then
mask out GSO features to force fall back to software GSO.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 14 Sep 2012 17:32:13 +0000 (10:32 -0700)]
Linux 3.0.43
Luca Tettamanti [Tue, 21 Aug 2012 15:36:28 +0000 (17:36 +0200)]
hwmon: (asus_atk0110) Add quirk for Asus M5A78L
commit
43ca6cb28c871f2fbad10117b0648e5ae3b0f638 upstream.
The old interface is bugged and reads the wrong sensor when retrieving
the reading for the chassis fan (it reads the CPU sensor); the new
interface works fine.
Reported-by: Göran Uddeborg <goeran@uddeborg.se>
Tested-by: Göran Uddeborg <goeran@uddeborg.se>
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 15 Aug 2012 11:31:54 +0000 (11:31 +0000)]
dccp: check ccid before dereferencing
commit
276bdb82dedb290511467a5a4fdbe9f0b52dce6f upstream.
ccid_hc_rx_getsockopt() and ccid_hc_tx_getsockopt() might be called with
a NULL ccid pointer leading to a NULL pointer dereference. This could
lead to a privilege escalation if the attacker is able to map page 0 and
prepare it with a fake ccid_ops pointer.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mel Gorman [Mon, 23 Jul 2012 11:16:19 +0000 (12:16 +0100)]
PARISC: Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
commit
bba3d8c3b3c0f2123be5bc687d1cddc13437c923 upstream.
The following build error occured during a parisc build with
swap-over-NFS patches applied.
net/core/sock.c:274:36: error: initializer element is not constant
net/core/sock.c:274:36: error: (near initialization for 'memalloc_socks')
net/core/sock.c:274:36: error: initializer element is not constant
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Airlie [Wed, 29 Aug 2012 01:40:51 +0000 (21:40 -0400)]
drm/vmwgfx: add MODULE_DEVICE_TABLE so vmwgfx loads at boot
commit
c4903429a92be60e6fe59868924a65eca4cd1a38 upstream.
This will cause udev to load vmwgfx instead of waiting for X
to do it.
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Torokhov [Wed, 22 Aug 2012 04:57:15 +0000 (21:57 -0700)]
Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
commit
7b125b94ca16b7e618c6241cb02c4c8060cea5e3 upstream.
They all define their chassis type as "Other" and therefore are not
categorized as "laptops" by the driver, which tries to perform AUX IRQ
delivery test which fails and causes touchpad not working.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42620
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Tue, 4 Sep 2012 16:45:54 +0000 (18:45 +0200)]
fuse: fix retrieve length
commit
c9e67d483776d8d2a5f3f70491161b205930ffe1 upstream.
In some cases fuse_retrieve() would return a short byte count if offset was
non-zero. The data returned was correct, though.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Mon, 3 Sep 2012 14:50:42 +0000 (16:50 +0200)]
ext3: Fix fdatasync() for files with only i_size changes
commit
156bddd8e505b295540f3ca0e27dda68cb0d49aa upstream.
Code tracking when transaction needs to be committed on fdatasync(2) forgets
to handle a situation when only inode's i_size is changed. Thus in such
situations fdatasync(2) doesn't force transaction with new i_size to disk
and that can result in wrong i_size after a crash.
Fix the issue by updating inode's i_datasync_tid whenever its size is
updated.
Reported-by: Kristian Nielsen <knielsen@knielsen-hq.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Wed, 5 Sep 2012 13:48:23 +0000 (15:48 +0200)]
udf: Fix data corruption for files in ICB
commit
9c2fc0de1a6e638fe58c354a463f544f42a90a09 upstream.
When a file is stored in ICB (inode), we overwrite part of the file, and
the page containing file's data is not in page cache, we end up corrupting
file's data by overwriting them with zeros. The problem is we use
simple_write_begin() which simply zeroes parts of the page which are not
written to. The problem has been introduced by
be021ee4 (udf: convert to
new aops).
Fix the problem by providing a ->write_begin function which makes the page
properly uptodate.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Wed, 25 Jul 2012 19:55:55 +0000 (23:55 +0400)]
SCSI: Fix 'Device not ready' issue on mpt2sas
commit
14216561e164671ce147458653b1fea06a4ada1e upstream.
This is a particularly nasty SCSI ATA Translation Layer (SATL) problem.
SAT-2 says (section 8.12.2)
if the device is in the stopped state as the result of
processing a START STOP UNIT command (see 9.11), then the SATL
shall terminate the TEST UNIT READY command with CHECK CONDITION
status with the sense key set to NOT READY and the additional
sense code of LOGICAL UNIT NOT READY, INITIALIZING COMMAND
REQUIRED;
mpt2sas internal SATL seems to implement this. The result is very confusing
standby behaviour (using hdparm -y). If you suspend a drive and then send
another command, usually it wakes up. However, if the next command is a TEST
UNIT READY, the SATL sees that the drive is suspended and proceeds to follow
the SATL rules for this, returning NOT READY to all subsequent commands. This
means that the ordering of TEST UNIT READY is crucial: if you send TUR and
then a command, you get a NOT READY to both back. If you send a command and
then a TUR, you get GOOD status because the preceeding command woke the drive.
This bit us badly because
commit
85ef06d1d252f6a2e73b678591ab71caad4667bb
Author: Tejun Heo <tj@kernel.org>
Date: Fri Jul 1 16:17:47 2011 +0200
block: flush MEDIA_CHANGE from drivers on close(2)
Changed our ordering on TEST UNIT READY commands meaning that SATA drives
connected to an mpt2sas now suspend and refuse to wake (because the mpt2sas
SATL sees the suspend *before* the drives get awoken by the next ATA command)
resulting in lots of failed commands.
The standard is completely nuts forcing this inconsistent behaviour, but we
have to work around it.
The fix for this is twofold:
1. Set the allow_restart flag so we wake the drive when we see it has been
suspended
2. Return all TEST UNIT READY status directly to the mid layer without any
further error handling which prevents us causing error handling which
may offline the device just because of a media check TUR.
Reported-by: Matthias Prager <linux@matthiasprager.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sreekanth.reddy@lsi.com [Tue, 17 Jul 2012 10:27:05 +0000 (15:57 +0530)]
SCSI: mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value
commit
338b131a3269881c7431234855c93c219b0979b6 upstream.
If the specified max_queue_depth setting is less than the
expected number of internal commands, then driver will calculate
the queue depth size to a negitive number. This negitive number
is actually a very large number because variable is unsigned
16bit integer. So, the driver will ask for a very large amount of
memory for message frames and resulting into oops as memory
allocation routines will not able to handle such a large request.
So, in order to limit this kind of oops, The driver need to set
the max_queue_depth to a scsi mid layer's can_queue value. Then
the overall message frames required for IO is minimum of either
(max_queue_depth plus internal commands) or the IOC global
credits.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kashyap Desai [Wed, 18 Jul 2012 01:20:44 +0000 (18:20 -0700)]
SCSI: megaraid_sas: Move poll_aen_lock initializer
commit
bd8d6dd43a77bfd2b8fef5b094b9d6095e169dee upstream.
The following patch moves the poll_aen_lock initializer from
megasas_probe_one() to megasas_init(). This prevents a crash when a user
loads the driver and tries to issue a poll() system call on the ioctl
interface with no adapters present.
Signed-off-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Jones [Thu, 6 Sep 2012 16:01:00 +0000 (12:01 -0400)]
Remove user-triggerable BUG from mpol_to_str
commit
80de7c3138ee9fd86a98696fd2cf7ad89b995d0a upstream.
Trivially triggerable, found by trinity:
kernel BUG at mm/mempolicy.c:2546!
Process trinity-child2 (pid: 23988, threadinfo
ffff88010197e000, task
ffff88007821a670)
Call Trace:
show_numa_map+0xd5/0x450
show_pid_numa_map+0x13/0x20
traverse+0xf2/0x230
seq_read+0x34b/0x3e0
vfs_read+0xac/0x180
sys_pread64+0xa2/0xc0
system_call_fastpath+0x1a/0x1f
RIP: mpol_to_str+0x156/0x360
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Blanchard [Mon, 3 Sep 2012 16:51:10 +0000 (16:51 +0000)]
powerpc: Restore correct DSCR in context switch
commit
714332858bfd40dcf8f741498336d93875c23aa7 upstream.
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
With the four patches applied I can run a combination of all
test cases successfully at the same time:
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
http://ozlabs.org/~anton/junkcode/dscr_inherit_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Blanchard [Mon, 3 Sep 2012 16:49:47 +0000 (16:49 +0000)]
powerpc: Fix DSCR inheritance in copy_thread()
commit
1021cb268b3025573c4811f1dee4a11260c4507b upstream.
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
This was found with the following test case:
http://ozlabs.org/~anton/junkcode/dscr_default_test.c
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Schnelle [Fri, 17 Aug 2012 19:43:43 +0000 (21:43 +0200)]
USB: CDC ACM: Fix NULL pointer dereference
commit
99f347caa4568cb803862730b3b1f1942639523f upstream.
If a device specifies zero endpoints in its interface descriptor,
the kernel oopses in acm_probe(). Even though that's clearly an
invalid descriptor, we should test wether we have all endpoints.
This is especially bad as this oops can be triggered by just
plugging a USB device in.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:26 +0000 (17:48 -0700)]
USB: smsusb: remove __devinit* from the struct usb_device_id table
commit
d04dbd1c0ec17a13326c8f2279399c225836a79f upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: Michael Krufky <mkrufky@linuxtv.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Doron Cohen <doronc@siano-ms.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:29 +0000 (17:48 -0700)]
USB: rtl8187: remove __devinit* from the struct usb_device_id table
commit
a3433179d0822ccfa8e80aa4d1d52843bd2dcc63 upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Herton Ronaldo Krzesinski <herton@canonical.com>
CC: Hin-Tak Leung <htl10@users.sourceforge.net>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:28 +0000 (17:48 -0700)]
USB: p54usb: remove __devinit* from the struct usb_device_id table
commit
b9c4167cbbafddac3462134013bc15e63e4c53ef upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Christian Lamparter <chunkeey@googlemail.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:27 +0000 (17:48 -0700)]
USB: spca506: remove __devinit* from the struct usb_device_id table
commit
e694d518886c7afedcdd1732477832b2e32744e4 upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hugh Dickins [Thu, 23 Aug 2012 10:17:36 +0000 (12:17 +0200)]
block: replace __getblk_slow misfix by grow_dev_page fix
commit
676ce6d5ca3098339c028d44fe0427d1566a4d2d upstream.
Commit
91f68c89d8f3 ("block: fix infinite loop in __getblk_slow")
is not good: a successful call to grow_buffers() cannot guarantee
that the page won't be reclaimed before the immediate next call to
__find_get_block(), which is why there was always a loop there.
Yesterday I got "EXT4-fs error (device loop0): __ext4_get_inode_loc:3595:
inode #19278: block 664: comm cc1: unable to read itable block" on console,
which pointed to this commit.
I've been trying to bisect for weeks, why kbuild-on-ext4-on-loop-on-tmpfs
sometimes fails from a missing header file, under memory pressure on
ppc G5. I've never seen this on x86, and I've never seen it on 3.5-rc7
itself, despite that commit being in there: bisection pointed to an
irrelevant pinctrl merge, but hard to tell when failure takes between
18 minutes and 38 hours (but so far it's happened quicker on 3.6-rc2).
(I've since found such __ext4_get_inode_loc errors in /var/log/messages
from previous weeks: why the message never appeared on console until
yesterday morning is a mystery for another day.)
Revert
91f68c89d8f3, restoring __getblk_slow() to how it was (plus
a checkpatch nitfix). Simplify the interface between grow_buffers()
and grow_dev_page(), and avoid the infinite loop beyond end of device
by instead checking init_page_buffers()'s end_block there (I presume
that's more efficient than a repeated call to blkdev_max_block()),
returning -ENXIO to __getblk_slow() in that case.
And remove akpm's ten-year-old "__getblk() cannot fail ... weird"
comment, but that is worrying: are all users of __getblk() really
now prepared for a NULL bh beyond end of device, or will some oops??
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Sun, 12 Aug 2012 21:26:07 +0000 (23:26 +0200)]
PCI: EHCI: Fix crash during hibernation on ASUS computers
commit
0b68c8e2c3afaf9807eb1ebe0ccfb3b809570aa4 upstream.
Commit
dbf0e4c (PCI: EHCI: fix crash during suspend on ASUS
computers) added a workaround for an ASUS suspend issue related to
USB EHCI and a bug in a number of ASUS BIOSes that attempt to shut
down the EHCI controller during system suspend if its PCI command
register doesn't contain 0 at that time.
It turns out that the same workaround is necessary in the analogous
hibernation code path, so add it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=45811
Reported-and-tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lorenzo Bianconi [Fri, 10 Aug 2012 09:00:24 +0000 (11:00 +0200)]
ath9k: fix decrypt_error initialization in ath_rx_tasklet()
commit
e1352fde5682ab1bdd2a9e5d75c22d1fe210ef77 upstream.
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Mon, 20 Aug 2012 14:57:22 +0000 (10:57 -0400)]
ACPI: export symbol acpi_get_table_with_size
commit
4f81f986761a7663db7d24d24cd6ae68008f1fc2 upstream.
We need it in the radeon drm module to fetch
and verify the vbios image on UEFI systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen M. Cameron [Tue, 21 Aug 2012 23:15:49 +0000 (16:15 -0700)]
cciss: fix incorrect scsi status reporting
commit
b0cf0b118c90477d1a6811f2cd2307f6a5578362 upstream.
Delete code which sets SCSI status incorrectly as it's already been set
correctly above this incorrect code. The bug was introduced in 2009 by
commit
b0e15f6db111 ("cciss: fix typo that causes scsi status to be
lost.")
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-by: Roel van Meer <roel.vanmeer@bokxing.nl>
Tested-by: Roel van Meer <roel.vanmeer@bokxing.nl>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
J. Bruce Fields [Mon, 20 Aug 2012 20:04:40 +0000 (16:04 -0400)]
svcrpc: sends on closed socket should stop immediately
commit
f06f00a24d76e168ecb38d352126fd203937b601 upstream.
svc_tcp_sendto sets XPT_CLOSE if we fail to transmit the entire reply.
However, the XPT_CLOSE won't be acted on immediately. Meanwhile other
threads could send further replies before the socket is really shut
down. This can manifest as data corruption: for example, if a truncated
read reply is followed by another rpc reply, that second reply will look
to the client like further read data.
Symptoms were data corruption preceded by svc_tcp_sendto logging
something like
kernel: rpc-srv/tcp: nfsd: sent only 963696 when sending
1048708 bytes - shutting down socket
Reported-by: Malahal Naineni <malahal@us.ibm.com>
Tested-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
J. Bruce Fields [Fri, 17 Aug 2012 21:31:53 +0000 (17:31 -0400)]
svcrpc: fix svc_xprt_enqueue/svc_recv busy-looping
commit
d10f27a750312ed5638c876e4bd6aa83664cccd8 upstream.
The rpc server tries to ensure that there will be room to send a reply
before it receives a request.
It does this by tracking, in xpt_reserved, an upper bound on the total
size of the replies that is has already committed to for the socket.
Currently it is adding in the estimate for a new reply *before* it
checks whether there is space available. If it finds that there is not
space, it then subtracts the estimate back out.
This may lead the subsequent svc_xprt_enqueue to decide that there is
space after all.
The results is a svc_recv() that will repeatedly return -EAGAIN, causing
server threads to loop without doing any actual work.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
J. Bruce Fields [Thu, 9 Aug 2012 22:12:28 +0000 (18:12 -0400)]
svcrpc: fix BUG() in svc_tcp_clear_pages
commit
be1e44441a560c43c136a562d49a1c9623c91197 upstream.
Examination of svc_tcp_clear_pages shows that it assumes sk_tcplen is
consistent with sk_pages[] (in particular, sk_pages[n] can't be NULL if
sk_tcplen would lead us to expect n pages of data).
svc_tcp_restore_pages zeroes out sk_pages[] while leaving sk_tcplen.
This is OK, since both functions are serialized by XPT_BUSY. However,
that means the inconsistency must be repaired before dropping XPT_BUSY.
Therefore we should be ensuring that svc_tcp_save_pages repairs the
problem before exiting svc_tcp_recv_record on error.
Symptoms were a BUG() in svc_tcp_clear_pages.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Wed, 15 Aug 2012 10:55:22 +0000 (12:55 +0200)]
audit: fix refcounting in audit-tree
commit
a2140fc0cb0325bb6384e788edd27b9a568714e2 upstream.
Refcounting of fsnotify_mark in audit tree is broken. E.g:
refcount
create_chunk
alloc_chunk 1
fsnotify_add_mark 2
untag_chunk
fsnotify_get_mark 3
fsnotify_destroy_mark
audit_tree_freeing_mark 2
fsnotify_put_mark 1
fsnotify_put_mark 0
via destroy_list
fsnotify_mark_destroy -1
This was reported by various people as triggering Oops when stopping auditd.
We could just remove the put_mark from audit_tree_freeing_mark() but that would
break freeing via inode destruction. So this patch simply omits a put_mark
after calling destroy_mark or adds a get_mark before.
The additional get_mark is necessary where there's no other put_mark after
fsnotify_destroy_mark() since it assumes that the caller is holding a reference
(or the inode is keeping the mark pinned, not the case here AFAICS).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reported-by: Valentin Avram <aval13@gmail.com>
Reported-by: Peter Moody <pmoody@google.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Wed, 15 Aug 2012 10:55:22 +0000 (12:55 +0200)]
audit: don't free_chunk() after fsnotify_add_mark()
commit
0fe33aae0e94b4097dd433c9399e16e17d638cd8 upstream.
Don't do free_chunk() after fsnotify_add_mark(). That one does a delayed unref
via the destroy list and this results in use-after-free.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bjschuma@gmail.com [Wed, 8 Aug 2012 17:57:10 +0000 (13:57 -0400)]
NFS: Alias the nfs module to nfs4
commit
425e776d93a7a5070b77d4f458a5bab0f924652c upstream.
This allows distros to remove the line from their modprobe
configuration.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Wed, 8 Aug 2012 20:03:13 +0000 (16:03 -0400)]
NFSv4.1: Remove a bogus BUG_ON() in nfs4_layoutreturn_done
commit
47fbf7976e0b7d9dcdd799e2a1baba19064d9631 upstream.
Ever since commit
0a57cdac3f (NFSv4.1 send layoutreturn to fence
disconnected data server) we've been sending layoutreturn calls
while there is potentially still outstanding I/O to the data
servers. The reason we do this is to avoid races between replayed
writes to the MDS and the original writes to the DS.
When this happens, the BUG_ON() in nfs4_layoutreturn_done can
be triggered because it assumes that we would never call
layoutreturn without knowing that all I/O to the DS is
finished. The fix is to remove the BUG_ON() now that the
assumptions behind the test are obsolete.
Reported-by: Boaz Harrosh <bharrosh@panasas.com>
Reported-by: Tigran Mkrtchyan <tigran.mkrtchyan@desy.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Mon, 20 Aug 2012 16:42:15 +0000 (12:42 -0400)]
NFSv3: Ensure that do_proc_get_root() reports errors correctly
commit
086600430493e04b802bee6e5b3ce0458e4eb77f upstream.
If the rpc call to NFS3PROC_FSINFO fails, then we need to report that
error so that the mount fails. Otherwise we can end up with a
superblock with completely unusable values for block sizes, maxfilesize,
etc.
Reported-by: Yuanming Chen <hikvision_linux@163.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Hocko [Tue, 21 Aug 2012 23:15:52 +0000 (16:15 -0700)]
mm: hugetlbfs: correctly populate shared pmd
commit
eb48c071464757414538c68a6033c8f8c15196f8 upstream.
Each page mapped in a process's address space must be correctly
accounted for in _mapcount. Normally the rules for this are
straightforward but hugetlbfs page table sharing is different. The page
table pages at the PMD level are reference counted while the mapcount
remains the same.
If this accounting is wrong, it causes bugs like this one reported by
Larry Woodman:
kernel BUG at mm/filemap.c:135!
invalid opcode: 0000 [#1] SMP
CPU 22
Modules linked in: bridge stp llc sunrpc binfmt_misc dcdbas microcode pcspkr acpi_pad acpi]
Pid: 18001, comm: mpitest Tainted: G W 3.3.0+ #4 Dell Inc. PowerEdge R620/07NDJ2
RIP: 0010:[<
ffffffff8112cfed>] [<
ffffffff8112cfed>] __delete_from_page_cache+0x15d/0x170
Process mpitest (pid: 18001, threadinfo
ffff880428972000, task
ffff880428b5cc20)
Call Trace:
delete_from_page_cache+0x40/0x80
truncate_hugepages+0x115/0x1f0
hugetlbfs_evict_inode+0x18/0x30
evict+0x9f/0x1b0
iput_final+0xe3/0x1e0
iput+0x3e/0x50
d_kill+0xf8/0x110
dput+0xe2/0x1b0
__fput+0x162/0x240
During fork(), copy_hugetlb_page_range() detects if huge_pte_alloc()
shared page tables with the check dst_pte == src_pte. The logic is if
the PMD page is the same, they must be shared. This assumes that the
sharing is between the parent and child. However, if the sharing is
with a different process entirely then this check fails as in this
diagram:
parent
|
------------>pmd
src_pte----------> data page
^
other--------->pmd--------------------|
^
child-----------|
dst_pte
For this situation to occur, it must be possible for Parent and Other to
have faulted and failed to share page tables with each other. This is
possible due to the following style of race.
PROC A PROC B
copy_hugetlb_page_range copy_hugetlb_page_range
src_pte == huge_pte_offset src_pte == huge_pte_offset
!src_pte so no sharing !src_pte so no sharing
(time passes)
hugetlb_fault hugetlb_fault
huge_pte_alloc huge_pte_alloc
huge_pmd_share huge_pmd_share
LOCK(i_mmap_mutex)
find nothing, no sharing
UNLOCK(i_mmap_mutex)
LOCK(i_mmap_mutex)
find nothing, no sharing
UNLOCK(i_mmap_mutex)
pmd_alloc pmd_alloc
LOCK(instantiation_mutex)
fault
UNLOCK(instantiation_mutex)
LOCK(instantiation_mutex)
fault
UNLOCK(instantiation_mutex)
These two processes are not poing to the same data page but are not
sharing page tables because the opportunity was missed. When either
process later forks, the src_pte == dst pte is potentially insufficient.
As the check falls through, the wrong PTE information is copied in
(harmless but wrong) and the mapcount is bumped for a page mapped by a
shared page table leading to the BUG_ON.
This patch addresses the issue by moving pmd_alloc into huge_pmd_share
which guarantees that the shared pud is populated in the same critical
section as pmd. This also means that huge_pte_offset test in
huge_pmd_share is serialized correctly now which in turn means that the
success of the sharing will be higher as the racing tasks see the pud
and pmd populated together.
Race identified and changelog written mostly by Mel Gorman.
{akpm@linux-foundation.org: attempt to make the huge_pmd_share() comment comprehensible, clean up coding style]
Reported-by: Larry Woodman <lwoodman@redhat.com>
Tested-by: Larry Woodman <lwoodman@redhat.com>
Reviewed-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Ken Chen <kenchen@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:37 +0000 (17:48 -0700)]
USB: winbond: remove __devinit* from the struct usb_device_id table
commit
43a34695d9cd79c6659f09da6d3b0624f3dd169f upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Pavel Machek <pavel@ucw.cz>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Eliad Peller <eliad@wizery.com>
CC: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Cree [Sun, 19 Aug 2012 02:40:56 +0000 (14:40 +1200)]
alpha: Don't export SOCK_NONBLOCK to user space.
commit
a2fa3ccd7b43665fe14cb562761a6c3d26a1d13f upstream.
Currently we export SOCK_NONBLOCK to user space but that conflicts with
the definition from glibc leading to compilation errors in user programs
(e.g. see Debian bug #658460).
The generic socket.h restricts the definition of SOCK_NONBLOCK to the
kernel, as does the MIPS specific socket.h, so let's do the same on
Alpha.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Wed, 15 Aug 2012 11:01:24 +0000 (13:01 +0200)]
vfs: canonicalize create mode in build_open_flags()
commit
e68726ff72cf7ba5e7d789857fcd9a75ca573f03 upstream.
Userspace can pass weird create mode in open(2) that we canonicalize to
"(mode & S_IALLUGO) | S_IFREG" in vfs_create().
The problem is that we use the uncanonicalized mode before calling vfs_create()
with unforseen consequences.
So do the canonicalization early in build_open_flags().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Mon, 20 Aug 2012 14:28:00 +0000 (15:28 +0100)]
vfs: missed source of ->f_pos races
commit
0e665d5d1125f9f4ccff56a75e814f10f88861a2 upstream.
compat_sys_{read,write}v() need the same "pass a copy of file->f_pos" thing
as sys_{read,write}{,v}().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Brown [Thu, 16 Aug 2012 21:36:04 +0000 (22:36 +0100)]
ASoC: wm9712: Fix microphone source selection
commit
ccf795847a38235ee4a56a24129ce75147d6ba8f upstream.
Currently the microphone input source is not selectable as while there is
a DAPM widget it's not connected to anything so it won't be properly
instantiated. Add something more correct for the input structure to get
things going, even though it's not hooked into the rest of the routing
map and so won't actually achieve anything except allowing the relevant
register bits to be written.
Reported-by: Christop Fritz <chf.fritz@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Thu, 16 Aug 2012 10:40:40 +0000 (10:40 +0000)]
ARM: imx: select CPU_FREQ_TABLE when needed
commit
f637c4c9405e21f44cf0045eaf77eddd3a79ca5a upstream.
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Stuebner [Tue, 7 Aug 2012 10:12:05 +0000 (19:12 +0900)]
ARM: S3C24XX: Fix s3c2410_dma_enqueue parameters
commit
b01858c7806e7e6f6121da2e51c9222fc4d21dc6 upstream.
Commit
d670ac019f60 (ARM: SAMSUNG: DMA Cleanup as per sparse) changed the
prototype of the s3c2410_dma_* functions to use the enum dma_ch instead
of an generic unsigned int.
In the s3c24xx dma.c s3c2410_dma_enqueue seems to have been forgotten,
the other functions there were changed correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 10 Aug 2012 18:13:36 +0000 (19:13 +0100)]
ARM: 7489/1: errata: fix workaround for erratum #720789 on UP systems
commit
730a8128cd8978467eb1cf546b11014acb57d433 upstream.
Commit
5a783cbc4836 ("ARM: 7478/1: errata: extend workaround for erratum
#720789") added workarounds for erratum #720789 to the range TLB
invalidation functions with the observation that the erratum only
affects SMP platforms. However, when running an SMP_ON_UP kernel on a
uniprocessor platform we must take care to preserve the ASID as the
workaround is not required.
This patch ensures that we don't set the ASID to 0 when flushing the TLB
on such a system, preserving the original behaviour with the workaround
disabled.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 10 Aug 2012 16:51:19 +0000 (17:51 +0100)]
ARM: 7488/1: mm: use 5 bits for swapfile type encoding
commit
f5f2025ef3e2cdb593707cbf87378761f17befbe upstream.
Page migration encodes the pfn in the offset field of a swp_entry_t.
For LPAE, we support physical addresses of up to 36 bits (due to
sparsemem limitations with the size of page flags), requiring 24 bits
to represent a pfn. A further 3 bits are used to encode a swp_entry into
a pte, leaving 5 bits for the type field. Furthermore, the core code
defines MAX_SWAPFILES_SHIFT as 5, so the additional type bit does not
get used.
This patch reduces the width of the type field to 5 bits, allowing us
to create up to 31 swapfiles of 64GB each.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 10 Aug 2012 16:51:18 +0000 (17:51 +0100)]
ARM: 7487/1: mm: avoid setting nG bit for user mappings that aren't present
commit
47f1204329237a0f8655f5a9f14a38ac81946ca1 upstream.
Swap entries are encoding in ptes such that !pte_present(pte) and
pte_file(pte). The remaining bits of the descriptor are used to identify
the swapfile and offset within it to the swap entry.
When writing such a pte for a user virtual address, set_pte_at
unconditionally sets the nG bit, which (in the case of LPAE) will
corrupt the swapfile offset and lead to a BUG:
[ 140.494067] swap_free: Unused swap offset entry
000763b4
[ 140.509989] BUG: Bad page map in process rs:main Q:Reg pte:
0ec76800 pmd:
8f92e003
This patch fixes the problem by only setting the nG bit for user
mappings that are actually present.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wang Xingchao [Mon, 13 Aug 2012 06:11:10 +0000 (14:11 +0800)]
ALSA: hda - fix Copyright debug message
commit
088c820b732dbfd515fc66d459d5f5777f79b406 upstream.
As spec said, 1 indicates no copyright is asserted.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:41 +0000 (17:48 -0700)]
USB: emi62: remove __devinit* from the struct usb_device_id table
commit
83957df21dd94655d2b026e0944a69ff37b83988 upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 18 Aug 2012 00:48:33 +0000 (17:48 -0700)]
USB: vt6656: remove __devinit* from the struct usb_device_id table
commit
4d088876f24887cd15a29db923f5f37db6a99f21 upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Forest Bond <forest@alittletooquiet.net>
CC: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jesper Juhl <jj@chaosbits.net>
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sun, 26 Aug 2012 22:12:29 +0000 (15:12 -0700)]
Linux 3.0.42
Bart Van Assche [Tue, 14 Aug 2012 13:18:53 +0000 (13:18 +0000)]
IB/srp: Fix a race condition
commit
220329916c72ee3d54ae7262b215a050f04a18fc upstream.
Avoid a crash caused by the scmnd->scsi_done(scmnd) call in
srp_process_rsp() being invoked with scsi_done == NULL. This can
happen if a reply is received during or after a command abort.
Reported-by: Joseph Glanville <joseph.glanville@orionvm.com.au>
Reference: http://marc.info/?l=linux-rdma&m=
134314367801595
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeongdo Son [Thu, 14 Jun 2012 17:28:01 +0000 (02:28 +0900)]
rt2x00: Add support for BUFFALO WLI-UC-GNM2 to rt2800usb.
commit
a769f9577232afe2c754606a83aad85127e7052a upstream.
This is a RT3070 based device.
Signed-off-by: Jeongdo Son <sohn9086@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Ferrell [Tue, 24 Jul 2012 19:15:13 +0000 (14:15 -0500)]
usb: serial: mos7840: Fixup mos7840_chars_in_buffer()
commit
5c263b92f828af6a8cf54041db45ceae5af8f2ab upstream.
* Use the buffer content length as opposed to the total buffer size. This can
be a real problem when using the mos7840 as a usb serial-console as all
kernel output is truncated during boot.
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ozan Çağlayan [Fri, 10 Aug 2012 14:25:10 +0000 (17:25 +0300)]
USB: ftdi_sio: Add VID/PID for Kondo Serial USB
commit
7724a1edbe463b06d4e7831a41149ba095b16c53 upstream.
This adds VID/PID for Kondo Kagaku Co. Ltd. Serial USB Adapter
interface:
http://www.kondo-robot.com/EN/wp/?cat=28
Tested by controlling an RCB3 board using libRCB3.
Signed-off-by: Ozan Çağlayan <ozancag@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Wed, 15 Aug 2012 13:43:33 +0000 (15:43 +0200)]
USB: option: add ZTE K5006-Z
commit
f1b5c997e68533df1f96dcd3068a231bca495603 upstream.
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>