David Woodhouse [Thu, 30 Apr 2009 14:38:01 +0000 (15:38 +0100)]
solos: Add some margin-related parameters
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nathan Williams [Wed, 25 Mar 2009 09:33:42 +0000 (20:33 +1100)]
solos: Check for rogue received packets
Sometimes there can be received packets with the size field set to 0xFFFF.
This seems to only occur after an FPGA or firmware upgrade.
This patch discards packets with an invalid size.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nathan Williams [Wed, 25 Mar 2009 09:27:37 +0000 (20:27 +1100)]
solos: support new FPGA RAM layout
Buffer sizes have been changed to 2048 bytes.
Flash upgrades use a dedicated RAM block.
Add support for daughterboard.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 17 Mar 2009 15:10:51 +0000 (15:10 +0000)]
solos: Disable DMA until we have an FPGA update with it actually implemented.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nathan Williams [Fri, 6 Feb 2009 23:19:13 +0000 (10:19 +1100)]
solos: Automatically determine number of ports
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 17 Mar 2009 14:59:34 +0000 (14:59 +0000)]
solos: Reset device on unload, free pending skbs
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Fri, 30 Jan 2009 03:31:36 +0000 (14:31 +1100)]
solos: Swap upstream/downstream rates in status packet, clean up some more
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Fri, 30 Jan 2009 03:27:26 +0000 (14:27 +1100)]
solos: Set RX empty flag at startup only for !dma mode
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Fri, 30 Jan 2009 03:26:37 +0000 (14:26 +1100)]
solos: Don't clear config registers at startup
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Fri, 30 Jan 2009 03:23:52 +0000 (14:23 +1100)]
solos: Tidy up status interrupt handling, cope with 'ERROR' status
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Fri, 30 Jan 2009 03:23:22 +0000 (14:23 +1100)]
solos: Add 'reset' module parameter to reset the DSL chips on load
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 03:37:20 +0000 (14:37 +1100)]
solos: Remove debugging, commented-out test code
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 03:08:27 +0000 (14:08 +1100)]
solos: Clean up handling of card->tx_mask a little
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 01:17:09 +0000 (12:17 +1100)]
solos: Fix various bugs in status packet handling
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 00:31:28 +0000 (11:31 +1100)]
solos: Remove superfluous wait_queue_head_t from struct solos_param
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 00:29:12 +0000 (11:29 +1100)]
solos: Remove IRQF_DISABLED, don't frob IRQ enable on the FPGA in solos_irq()
Neither of these are necessary.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 00:12:58 +0000 (11:12 +1100)]
solos: Remove unused loopback debug stuff
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Thu, 29 Jan 2009 00:10:58 +0000 (11:10 +1100)]
solos: Tidy up tx_mask handling for ports which need TX
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Wed, 28 Jan 2009 23:51:11 +0000 (10:51 +1100)]
solos: Tidy up DMA handling a little. Still untested
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Wed, 28 Jan 2009 05:46:56 +0000 (16:46 +1100)]
solos: First attempt at DMA support
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Wed, 28 Jan 2009 03:34:34 +0000 (14:34 +1100)]
solos: Remove parameter group from sysfs on ATM dev deregister
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 23:39:23 +0000 (10:39 +1100)]
solos: Fix under-allocation of skb size for get/set parameters
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 23:22:57 +0000 (10:22 +1100)]
solos: Add SNR and Attn to status packet, fix oops on load
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 10:50:36 +0000 (21:50 +1100)]
solos: Reject non-AAL5 connections.... for now
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 10:47:47 +0000 (21:47 +1100)]
solos: Kill existing connections on link down event
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 09:02:30 +0000 (20:02 +1100)]
solos: Handle new line status change packets, hook up to ATM layer info
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 05:52:07 +0000 (16:52 +1100)]
solos: Add initial list of parameters
I don't much like the trick with multiple inclusions of solos-attrlist.c
but don't really see a saner way to do it without repeating the list.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 05:20:04 +0000 (16:20 +1100)]
solos: Handle attribute show/store in kernel more sanely
There are still a _lot_ of attributes, but for at least the basic ones
we want to be able to get/set them from the kernel. Especially the ones
we want to inform the ATM core about (link state, speed).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 03:25:16 +0000 (14:25 +1100)]
solos: Kill global 'opens' count.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Tue, 27 Jan 2009 03:16:12 +0000 (14:16 +1100)]
solos: Clean up firmware loading code
We no longer try to load firmware while the ATM is up and running.
However, this means that we _do_ make init_module() wait for it, and it
takes a long time for now (since we're using ultra-conservative code in
the FPGA for that too).
The inner loop which uses swahb32p() was by Simon Farnsworth.
Simon has patches which migrate us to request_firmware_nowait(), for
which we'll actually need to take down the ATM devices, do the upgrade,
then reregister them.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Simon Farnsworth [Wed, 21 Jan 2009 20:45:49 +0000 (20:45 +0000)]
solos: FPGA and firmware update support.
This is just a straight pull in of changes, syncing us up to 0.07 from
openadsl.sf.net
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Simon Farnsworth [Mon, 19 Jan 2009 21:19:29 +0000 (21:19 +0000)]
solos: Slight debugging improvements
Print a message if pskb_expand_head fails.
Make atmdebug writable by root, so that you can turn printing of data sent to
and received from the card on and off at runtime - useful for tracking
corruption.
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Woodhouse [Mon, 26 Jan 2009 23:18:51 +0000 (10:18 +1100)]
solos: Fix length header in FPGA transfers
The length field shouldn't ever include the size of the header itself.
This fixes the problem that some people were seeing with 1500-byte
packets.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds [Fri, 16 Jan 2009 20:43:00 +0000 (12:43 -0800)]
Linux 2.6.29-rc2
Linus Torvalds [Fri, 16 Jan 2009 20:40:37 +0000 (12:40 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI PCI hotplug: harden against panic regression
ACPI: rename main.c to sleep.c
dell-laptop: move to drivers/platform/x86/ from drivers/misc/
eeepc-laptop: enable Bluetooth ACPI details
ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
kprobes: check CONFIG_FREEZER instead of CONFIG_PM
PM: Fix freezer compilation if PM_SLEEP is unset
thermal fixup for broken BIOS which has invalid trip points.
ACPI: EC: Don't trust ECDT tables from ASUS
ACPI: EC: Limit workaround for ASUS notebooks even more
ACPI: thinkpad-acpi: bump up version to 0.22
ACPI: thinkpad-acpi: handle HKEY event 6030
ACPI: thinkpad-acpi: clean-up fan subdriver quirk
ACPI: thinkpad-acpi: start the event hunt season
ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms
ACPI: thinkpad-acpi: clean up hotkey_notify()
ACPI: thinkpad-acpi: use killable instead of interruptible mutexes
ACPI: thinkpad-acpi: add UWB radio support
ACPI: thinkpad-acpi: preserve radio state across shutdown
ACPI: thinkpad-acpi: resume with radios disabled
...
Linus Torvalds [Fri, 16 Jan 2009 20:40:11 +0000 (12:40 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netxen: include ipv6.h (fixes build failure)
netxen: avoid invalid iounmap
James Bottomley [Thu, 15 Jan 2009 20:12:27 +0000 (15:12 -0500)]
ACPI PCI hotplug: harden against panic regression
ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136
Rather than reverting the entire commit that causes the crash:
e8c331e963c58b83db24b7d0e39e8c07f687dbc6
"PCI hotplug: introduce functions for ACPI slot detection"
simply harden against it while the changes to
the hotplug code on this particularl machine are understood.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Fri, 16 Jan 2009 19:45:34 +0000 (14:45 -0500)]
Merge branch 'misc' into release
Len Brown [Fri, 16 Jan 2009 19:45:24 +0000 (14:45 -0500)]
Merge branch 'thinkpad-acpi' into release
Len Brown [Fri, 16 Jan 2009 19:45:11 +0000 (14:45 -0500)]
Merge branches 'bugzilla-11884' and 'bugzilla-8544' into release
Len Brown [Fri, 16 Jan 2009 18:52:03 +0000 (13:52 -0500)]
ACPI: rename main.c to sleep.c
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Fri, 9 Jan 2009 22:23:38 +0000 (17:23 -0500)]
dell-laptop: move to drivers/platform/x86/ from drivers/misc/
Signed-off-by: Len Brown <len.brown@intel.com>
Jonathan McDowell [Wed, 3 Dec 2008 20:31:11 +0000 (20:31 +0000)]
eeepc-laptop: enable Bluetooth ACPI details
Although rfkill support for the EEE bluetooth device has been added to
2.6.28-rc the appropriate ACPI accessor definitions were not added, so
the support was non functional. The patch below adds the get and set
accessors and has been verified to work on an EEE 901.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
David Brownell [Fri, 9 Jan 2009 20:17:08 +0000 (12:17 -0800)]
ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec;
that bit has nothing to do with status bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Masami Hiramatsu [Tue, 6 Jan 2009 20:15:32 +0000 (21:15 +0100)]
kprobes: check CONFIG_FREEZER instead of CONFIG_PM
Check CONFIG_FREEZER instead of CONFIG_PM because kprobe booster
depends on freeze_processes() and thaw_processes() when CONFIG_PREEMPT=y.
This fixes a linkage error which occurs when CONFIG_PREEMPT=y, CONFIG_PM=y
and CONFIG_FREEZER=n.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
Rafael J. Wysocki [Tue, 6 Jan 2009 20:14:04 +0000 (21:14 +0100)]
PM: Fix freezer compilation if PM_SLEEP is unset
Freezer fails to compile if with the following configuration
settings:
CONFIG_CGROUPS=y
CONFIG_CGROUP_FREEZER=y
CONFIG_MODULES=y
CONFIG_FREEZER=y
CONFIG_PM=y
CONFIG_PM_SLEEP=n
Fix this by making process.o compilation depend on CONFIG_FREEZER.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Fri, 16 Jan 2009 17:53:42 +0000 (12:53 -0500)]
thermal fixup for broken BIOS which has invalid trip points.
ACPI thermal driver only re-evaluate VALID trip points.
For the broken BIOS show in
http://bugzilla.kernel.org/show_bug.cgi?id=8544
the active[0] is set to invalid at boot time
and it will not be re-evaluated again.
We can still get a single warning message at boot time.
http://marc.info/?l=linux-kernel&m=
120496222629983&w=2
http://bugzilla.kernel.org/show_bug.cgi?id=12203
Signed-off-by: Zhang Rui<rui.zhang@intel.com>
Tested-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
Dhananjay Phadke [Fri, 16 Jan 2009 19:03:25 +0000 (11:03 -0800)]
netxen: include ipv6.h (fixes build failure)
Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Starikovskiy [Tue, 13 Jan 2009 23:57:53 +0000 (02:57 +0300)]
ACPI: EC: Don't trust ECDT tables from ASUS
http://bugzilla.kernel.org/show_bug.cgi?id=9399
http://bugzilla.kernel.org/show_bug.cgi?id=11880
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Dhananjay Phadke [Fri, 16 Jan 2009 19:03:01 +0000 (11:03 -0800)]
netxen: avoid invalid iounmap
For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.
"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Starikovskiy [Tue, 13 Jan 2009 23:57:47 +0000 (02:57 +0300)]
ACPI: EC: Limit workaround for ASUS notebooks even more
References: http://bugzilla.kernel.org/show_bug.cgi?id=11884
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Fri, 16 Jan 2009 17:32:33 +0000 (09:32 -0800)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix ioctl arg size (userland incompatible change!)
Btrfs: Clear the device->running_pending flag before bailing on congestion
Chris Mason [Fri, 16 Jan 2009 16:59:08 +0000 (11:59 -0500)]
Btrfs: fix ioctl arg size (userland incompatible change!)
The structure used to send device in btrfs ioctl calls was not
properly aligned, and so 32 bit ioctls would not work properly on
64 bit kernels.
We could fix this with compat ioctls, but we're just one byte away
and it doesn't make sense at this stage to carry about the compat ioctls
forever at this stage in the project.
This patch brings the ioctl arg up to an evenly aligned 4k.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Fri, 16 Jan 2009 16:58:19 +0000 (11:58 -0500)]
Btrfs: Clear the device->running_pending flag before bailing on congestion
Btrfs maintains a queue of async bio submissions so the checksumming
threads don't have to wait on get_request_wait. In order to avoid
extra wakeups, this code has a running_pending flag that is used
to tell new submissions they don't need to wake the thread.
When the threads notice congestion on a single device, they
may decide to requeue the job and move on to other devices. This
makes sure the running_pending flag is cleared before the
job is requeued.
It should help avoid IO stalls by making sure the task is woken up
when new submissions come in.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Fri, 16 Jan 2009 16:41:09 +0000 (08:41 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
serial: Add 16850 uart type support to OF uart driver
hvc_console: Remove tty->low_latency
powerpc: Get the number of SLBs from "slb-size" property
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3
powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block
powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc
powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments
powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
powerpc/ps3: The lv1_ routines have u64 parameters
powerpc/ps3: Use dma_addr_t down through the stack
powerpc/ps3: set_dabr() takes an unsigned long
powerpc: Cleanup from l64 to ll64 change drivers/scsi
Linus Torvalds [Fri, 16 Jan 2009 16:40:57 +0000 (08:40 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl: Return non-zero on error in probe()
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
libata: New driver for OCTEON SOC Compact Flash interface (v7).
libata: Add another column to the ata_timing table.
sata_via: Add VT8261 support
pata_atiixp: update port enabledness test handling
[libata] get-identity ioctl: Fix use of invalid memory pointer
Linus Torvalds [Fri, 16 Jan 2009 16:40:40 +0000 (08:40 -0800)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] Skip deleted devices in __scsi_device_lookup_by_target()
[SCSI] Add SUN Universal Xport to no attach blacklist
[SCSI] iscsi_tcp: make padbuf non-static
[SCSI] mpt fusion: Add Firmware debug support
[SCSI] mpt fusion: Add separate msi enable disable for FC,SPI,SAS
[SCSI] mpt fusion: Update MPI Headers to version 01.05.19
[SCSI] qla2xxx: Fix ISP restart bug in multiq code
Linus Torvalds [Fri, 16 Jan 2009 16:39:52 +0000 (08:39 -0800)]
Merge branch 'drm-next' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: lock correct mutex around object unreference.
drm/i915: add support for physical memory objects
drm/i915: make LVDS fixed mode a preferred mode
drm: handle depth & bpp changes correctly
drm: initial KMS config fixes
drm/i915: setup sarea properly in master_priv
drm/i915: set vblank enabled flag correctly across IRQ install/uninstall
drm/i915: don't enable vblanks on disabled pipes
Linus Torvalds [Fri, 16 Jan 2009 16:14:51 +0000 (08:14 -0800)]
Revert "PCI PM: Register power state of devices during initialization"
This reverts commit
98e6e286d7b01deb7453b717aa38ebb69d6cefc0, as Yinghai
Lu reports that it breaks kexec with at least the e1000 and e1000e
drivers. The reason is that the shutdown sequence puts the hardware
into D3 sleep, and the commit causes us to claim that it then is in D0
(running) state just because we don't understand the PM capabilities.
Which then later makes "pci_set_power_state()" not do anything, and the
device never wakes up properly and just returns 0xff to everything.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: From: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Sojka [Wed, 14 Jan 2009 13:02:38 +0000 (14:02 +0100)]
sata_fsl: Return non-zero on error in probe()
while I was looking over kernel sources I've found this small bug.
Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Andrew Morton [Thu, 15 Jan 2009 00:48:42 +0000 (16:48 -0800)]
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Daney [Fri, 16 Jan 2009 01:45:32 +0000 (17:45 -0800)]
libata: New driver for OCTEON SOC Compact Flash interface (v7).
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Daney [Fri, 16 Jan 2009 01:45:31 +0000 (17:45 -0800)]
libata: Add another column to the ata_timing table.
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
JosephChan@via.com.tw [Fri, 16 Jan 2009 11:44:55 +0000 (19:44 +0800)]
sata_via: Add VT8261 support
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 16 Jan 2009 06:27:27 +0000 (15:27 +0900)]
pata_atiixp: update port enabledness test handling
Port enabledness test fits much better into init_one() instead of
pre_reset(). The reason why these tests are in pre_reset() is purely
historical at this point. Move it to init_one(). This will help
further changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jeff Garzik [Fri, 16 Jan 2009 15:17:09 +0000 (10:17 -0500)]
[libata] get-identity ioctl: Fix use of invalid memory pointer
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Airlie [Thu, 15 Jan 2009 04:03:07 +0000 (14:03 +1000)]
drm/i915: lock correct mutex around object unreference.
This makes sure the mutex is held around the unreference.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 30 Dec 2008 10:31:46 +0000 (20:31 +1000)]
drm/i915: add support for physical memory objects
This is an initial patch to do support for objects which needs physical
contiguous main ram, cursors and overlay registers on older chipsets.
These objects are bound on cursor bin, like pinning, and we copy
the data to/from the backing store object into the real one on attach/detach.
notes:
possible over the top in attach/detach operations.
no overlay support yet.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jesse Barnes [Wed, 14 Jan 2009 18:53:36 +0000 (10:53 -0800)]
drm/i915: make LVDS fixed mode a preferred mode
The detected fixed panel mode really is preferred, so mark it as such and
add it to the LVDS connector mode list.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Jesse Barnes [Fri, 9 Jan 2009 21:56:14 +0000 (13:56 -0800)]
drm: handle depth & bpp changes correctly
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Jesse Barnes [Mon, 12 Jan 2009 20:05:32 +0000 (12:05 -0800)]
drm: initial KMS config fixes
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Matthias Fuchs [Thu, 15 Jan 2009 09:43:35 +0000 (09:43 +0000)]
serial: Add 16850 uart type support to OF uart driver
This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.
This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Hendrik Brueckner [Wed, 14 Jan 2009 23:15:44 +0000 (23:15 +0000)]
hvc_console: Remove tty->low_latency
This patch removes the tty->low_latency setting.
For irq based hvc_console backends the tty->low_latency must be set to 0,
because the tty_flip_buffer_push() function must not be called from IRQ context
(see drivers/char/tty_buffer.c).
For polled backends, the low_latency setting causes the bug trace below, because
tty_flip_buffer_push() is called within an atomic context and subsequent calls
might sleep due to mutex_lock.
BUG: sleeping function called from invalid context at /root/cvs/linux-2.6.git/kernel/mutex.c:207
in_atomic(): 1, irqs_disabled(): 0, pid: 748, name: khvcd
1 lock held by khvcd/748:
#0: (hvc_structs_lock){--..}, at: [<
00000000002ceb50>] khvcd+0x58/0x12c
CPU: 0 Not tainted 2.6.29-rc1git #29
Process khvcd (pid: 748, task:
000000002fb9a480, ksp:
000000002f66bd78)
070000000000000a 000000002f66ba00 0000000000000002 (null)
000000002f66baa0 000000002f66ba18 000000002f66ba18 0000000000104f08
ffffffffffffc000 000000002f66bd78 (null) (null)
000000002f66ba00 000000000000000c 000000002f66ba00 000000002f66ba70
0000000000466af8 0000000000104f08 000000002f66ba00 000000002f66ba50
Call Trace:
([<
0000000000104e7c>] show_trace+0x138/0x158)
[<
0000000000104f62>] show_stack+0xc6/0xf8
[<
0000000000105740>] dump_stack+0xb0/0xc0
[<
000000000013144a>] __might_sleep+0x14e/0x17c
[<
000000000045e226>] mutex_lock_nested+0x42/0x3b4
[<
00000000002c443e>] echo_char_raw+0x3a/0x9c
[<
00000000002c688c>] n_tty_receive_buf+0x1154/0x1208
[<
00000000002ca0a2>] flush_to_ldisc+0x152/0x220
[<
00000000002ca1da>] tty_flip_buffer_push+0x6a/0x90
[<
00000000002cea74>] hvc_poll+0x244/0x2c8
[<
00000000002ceb68>] khvcd+0x70/0x12c
[<
000000000015bbd0>] kthread+0x68/0xa0
[<
0000000000109d5a>] kernel_thread_starter+0x6/0xc
[<
0000000000109d54>] kernel_thread_starter+0x0/0xc
1 lock held by khvcd/748:
#0: (hvc_structs_lock){--..}, at: [<
00000000002ceb50>] khvcd+0x58/0x12c
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 14 Jan 2009 13:42:41 +0000 (13:42 +0000)]
powerpc: Get the number of SLBs from "slb-size" property
The PAPR says that the property for specifying the number of SLBs should
be called "slb-size". We currently only look for "ibm,slb-size" because
this is what firmware actually presents.
This patch makes us look for the "slb-size" property as well and in
preference to the "ibm,slb-size". This should future proof us if
firmware changes to match PAPR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Wed, 14 Jan 2009 09:09:34 +0000 (09:09 +0000)]
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
The subpage_prot syscall fails on second and subsequent calls for a given
region, because is_hugepage_only_range() is mis-identifying the 4 kB
slices when the process has a 64 kB page size.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:13:39 +0000 (20:13 +0000)]
powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:11:44 +0000 (20:11 +0000)]
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:10:06 +0000 (20:10 +0000)]
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3
Also some min -> mint_t conversion.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:07:55 +0000 (20:07 +0000)]
powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:06:02 +0000 (20:06 +0000)]
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char
Also a couple of min -> min_t changes.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:04:48 +0000 (20:04 +0000)]
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:02:39 +0000 (20:02 +0000)]
powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:01:28 +0000 (20:01 +0000)]
powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments
Fixes compiler warnings:
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 2 of 'ps3_repository_read_mm_info' from incompatible pointer type
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 3 of 'ps3_repository_read_mm_info' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 20:00:29 +0000 (20:00 +0000)]
powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
This fixes these compiler warning:
arch/powerpc/platforms/ps3/interrupt.c:109: warning: passing argument 2 of 'clear_bit' from incompatible pointer type
arch/powerpc/platforms/ps3/interrupt.c:130: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 19:59:41 +0000 (19:59 +0000)]
powerpc/ps3: The lv1_ routines have u64 parameters
We just fix up the reference parameters as the others are dealt with by
arithmetic promotion rules and don't cause warnings.
This removes warnings like this:
arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type
Also, these:
drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 19:58:10 +0000 (19:58 +0000)]
powerpc/ps3: Use dma_addr_t down through the stack
Push the dma_addr_t type usage all the way down to where the actual
values are manipulated.
Now that u64 is "unsigned long long", this removes warnings like:
arch/powerpc/platforms/ps3/system-bus.c:532: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
arch/powerpc/platforms/ps3/system-bus.c:649: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 13 Jan 2009 19:54:50 +0000 (19:54 +0000)]
powerpc/ps3: set_dabr() takes an unsigned long
Also silences this warning:
arch/powerpc/platforms/ps3/setup.c:275: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Tue, 6 Jan 2009 14:59:00 +0000 (14:59 +0000)]
powerpc: Cleanup from l64 to ll64 change drivers/scsi
This is a powerpc specific driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Fri, 16 Jan 2009 00:55:00 +0000 (16:55 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: sched_slice() fixlet
sched: fix update_min_vruntime
sched: SCHED_OTHER vs SCHED_IDLE isolation
sched: SCHED_IDLE weight change
sched: fix bandwidth validation for UID grouping
Revert "sched: improve preempt debugging"
Linus Torvalds [Fri, 16 Jan 2009 00:53:42 +0000 (16:53 -0800)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix UP build failure.
Linus Torvalds [Fri, 16 Jan 2009 00:53:15 +0000 (16:53 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (95 commits)
b44: GFP_DMA skb should not escape from driver
korina: do not use IRQF_SHARED with IRQF_DISABLED
korina: do not stop queue here
korina: fix handling tx_chain_tail
korina: do tx at the right position
korina: do schedule napi after testing for it
korina: rework korina_rx() for use with napi
korina: disable napi on close and restart
korina: reset resource buffer size to 1536
korina: fix usage of driver_data
bnx2x: First slow path interrupt race
bnx2x: MTU Filter
bnx2x: Indirection table initialization index
bnx2x: Missing brackets
bnx2x: Fixing the doorbell size
bnx2x: Endianness issues
bnx2x: VLAN tagged packets without VLAN offload
bnx2x: Protecting the link change indication
bnx2x: Flow control updated before reporting the link
bnx2x: Missing mask when calculating flow control
...
Linus Torvalds [Fri, 16 Jan 2009 00:40:12 +0000 (16:40 -0800)]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
hwmon: (abituguru3) Match partial DMI board name strings
hwmon: Add a driver for the ADT7475 hardware monitoring chip
hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
hwmon: (k8temp) Warn about fam F rev F errata
Roland Dreier [Thu, 15 Jan 2009 21:51:29 +0000 (13:51 -0800)]
9p: disallow RDMA if RDMA CM isn't available
If INET=y and INFINIBAND=y, but IPV6=m then INFINIBAND_ADDR_TRANS is set
to n and the RDMA CM functions rdma_connect() et al are not built.
However, the current config dependencies allow NET_9P_RDMA to be selected
in this, which leads to a build failure. Fix this by adding a dependency
on INFINIBAND_ADDR_TRANS to disallow NET_9P_RDMA in this case.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Thu, 15 Jan 2009 21:51:29 +0000 (13:51 -0800)]
ext2: also update the inode on disk when dir is IS_DIRSYNC
We used to just write changed page for IS_DIRSYNC inodes. But we also
have to update the directory inode itself just for the case that we've
allocated a new block and changed i_size.
[akpm@linux-foundation.org: still sync the data page]
Signed-off-by: Jan Kara <jack@suse.cz>
Tested-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Thu, 15 Jan 2009 21:51:28 +0000 (13:51 -0800)]
drivers/usb/core/hub.c: fix CONFIG_USB_OTG=y build
Carry out the PM-routine interface change in the USB OTG pathway. This
was omitted from the earlier interface-change patch by mistake.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jaswinder Singh Rajput [Thu, 15 Jan 2009 21:51:26 +0000 (13:51 -0800)]
include of <linux/types.h> is preferred over <asm/types.h>
Impact: fix 15 make headers_check warnings:
include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Thu, 15 Jan 2009 21:51:26 +0000 (13:51 -0800)]
memcg: fix a race when setting memory.swappiness
(suppose: memcg->use_hierarchy == 0 and memcg->swappiness == 60)
echo 10 > /memcg/0/swappiness |
mem_cgroup_swappiness_write() |
... | echo 1 > /memcg/0/use_hierarchy
| mkdir /mnt/0/1
| sub_memcg->swappiness = 60;
memcg->swappiness = 10; |
In the above scenario, we end up having 2 different swappiness
values in a single hierarchy.
We should hold cgroup_lock() when cheking cgrp->children list.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Thu, 15 Jan 2009 21:51:25 +0000 (13:51 -0800)]
memcg: fix section mismatch
At system boot when creating the top cgroup, mem_cgroup_create() calls
enable_swap_cgroup() which is marked as __init, so mark
mem_cgroup_create() as __ref to avoid false section mismatch warning.
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by; KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Machek [Thu, 15 Jan 2009 21:51:24 +0000 (13:51 -0800)]
hp_accel: do not call ACPI from invalid context
The LED on HP notebooks is connected through ACPI. That unfortunately
means that it needs to be delayed by using schedule_work() to avoid
calling the ACPI interpreter from an invalid context.
[akpm@linux-foundation.org: use flush_work() rather than sort-of reimplementing it]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Machek [Thu, 15 Jan 2009 21:51:24 +0000 (13:51 -0800)]
lis3: fix documentation to fit into 80 columns
Fix lis3 documentation to fit into 80 columns.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / firefly-linux-kernel-4.4.55.git / log