firefly-linux-kernel-4.4.55.git
12 years agomtd: fsmc: use ALE and CLE offsets from platform data
Shiraz Hashim [Wed, 7 Mar 2012 11:30:51 +0000 (17:00 +0530)]
mtd: fsmc: use ALE and CLE offsets from platform data

ALE and CLE offsets can be different on different devices. Let devices
pass these offsets to the fsmc driver through platform data.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: fsmc_nand: ECC1 & ECC4 layout separated for different page sizes
Bhavna Yadav [Wed, 7 Mar 2012 11:30:50 +0000 (17:00 +0530)]
mtd: fsmc_nand: ECC1 & ECC4 layout separated for different page sizes

ECC1 & ECC4 layout for NAND of different pages sizes for e.g. 512bytes,
2KiB, 4KiB and 8KiB are separated. Previously there existed one ECC4
layout for 2KiB & 4KiB page size due to which oob test module available
in drivers/mtd/nand/test was failing.

Signed-off-by: Bhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: fsmc: Newly erased page read algorithm implemented
Vipin Kumar [Wed, 7 Mar 2012 11:30:49 +0000 (17:00 +0530)]
mtd: fsmc: Newly erased page read algorithm implemented

A newly erased page contains ff in data as well as spare area. While reading an
erased page, the read out ecc from spare area does not match the ecc generated
by fsmc ecc hardware accelerator. This is because ecc of data ff ff is not ff
ff. This leads to errors when file system erases and reads back the pages to
ensure consistency.

This patch adds a software workaround to ensure that the ecc check is not
performed for erased pages. This problem is solved by checking the number of
bits (in 512 byte data + 13 byte ecc) which are 0. If these number of bits are
less than 8, the page is considered erased and correction algorithm is not tried
on that page

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: fix partition wrapper functions
Mike Dunn [Sat, 3 Mar 2012 21:13:06 +0000 (13:13 -0800)]
mtd: fix partition wrapper functions

This patch reverts a change that may have been mistakenly included with the set
of patches that introduced the new mtd api entry functions.  Or perhaps I am
mistaken :)

The problem is in the partition wrapper functions, where the calls to the driver
methods were replaced with calls to the new mtd api functions.  This causes the
api function to be called a second time, further down the call stack.  This is
not only unnecessary and redundant - because the sanity checking code and (more
restrictive) bounds checks for the partition were done in the first call - but
is potentially problematic and confusing.

For example, the call stack for a call to mtd_read() on a partitioned device
currently looks like this:

mtd_read()             gets struct mtd_info for the partition
|
+-> part_read()        via the pointer assigned when the partition was created
    |
    +->mtd_read()      this time gets struct mtd_info for the master
       |
       +->xyz_driver_read()  via the pointer asigned by the driver

It seems that this can cause a variety of problems.  For example, if you want to
add code to the api function that tests a value in mtd_info that is relevant
only to the partition.  Or (in my case) you want the driver to return a value
that may be different from that returned by the mtd api function.

This patch eliminates the second call to the mtd api function.  It was tested on
the docg4 nand driver with a subset of the api functions, but I inspected the
rest and don't see any problems.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: docg3 trivial renaming
Robert Jarzmik [Sat, 3 Mar 2012 20:57:33 +0000 (21:57 +0100)]
mtd: docg3 trivial renaming

Change the name of the mtd so that it is simpler, and is easier to
cope with by mtdparts.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agoARM: mach-shmobile: mackerel: Add the flash controller flctl
Bastian Hecht [Thu, 1 Mar 2012 09:48:41 +0000 (10:48 +0100)]
ARM: mach-shmobile: mackerel: Add the flash controller flctl

Add board and clock setup code for the SH Mobile flctl controller.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sh_flctl: Add FLHOLDCR register
Bastian Hecht [Thu, 1 Mar 2012 09:48:40 +0000 (10:48 +0100)]
mtd: sh_flctl: Add FLHOLDCR register

Add a register used in new FLCTL hardware and a feature flag for it.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sh_flctl: Use cached register value for FLCMNCR
Bastian Hecht [Thu, 1 Mar 2012 09:48:39 +0000 (10:48 +0100)]
mtd: sh_flctl: Use cached register value for FLCMNCR

Instead of reading out the register, use a cached value. This will
make way for a proper runtime power management implementation.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sh_flctl: Implement NAND_CMD_RNDOUT command
Bastian Hecht [Thu, 1 Mar 2012 09:48:38 +0000 (10:48 +0100)]
mtd: sh_flctl: Implement NAND_CMD_RNDOUT command

Implements the command to seek and read in pages.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sh_flctl: Expand the READID command to 8 bytes
Bastian Hecht [Thu, 1 Mar 2012 09:48:37 +0000 (10:48 +0100)]
mtd: sh_flctl: Expand the READID command to 8 bytes

The nand base code wants to read out 8 bytes in the READID command.
Reflect this in the driver code.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sh_flctl: Reorder empty_fifo() calls
Bastian Hecht [Thu, 1 Mar 2012 09:48:36 +0000 (10:48 +0100)]
mtd: sh_flctl: Reorder empty_fifo() calls

Reorders the calls to make it a bit shorter and match the calling
procedure displayed in the datasheet.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sh_flctl: Expand FLCMNCR register bit field
Bastian Hecht [Thu, 1 Mar 2012 09:48:35 +0000 (10:48 +0100)]
mtd: sh_flctl: Expand FLCMNCR register bit field

Add support for a new hardware generation. The meaning of some bits
of the FLCMNCR register changed, so some new defines are added
parallel to the existing ones to keep backward compatibility.

The defines allow to choose an appropriate clocking scheme.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: Standardize JFFS_<LEVEL> uses
Joe Perches [Wed, 15 Feb 2012 23:56:46 +0000 (15:56 -0800)]
jffs2: Standardize JFFS_<LEVEL> uses

Use pr_<level> to prefix KBUILD_MODNAME via pr_fmt.

Remove obfuscating defines and use constants in pr_<level>
No need for a do {} while (0) for single statements.

Form of JFFS_<LEVEL> output changes from
"JFFS2 notice: " to "jffs2: notice: "

Added pr_fmt to xattr.c

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: Use pr_fmt and remove jffs: from formats
Joe Perches [Wed, 15 Feb 2012 23:56:45 +0000 (15:56 -0800)]
jffs2: Use pr_fmt and remove jffs: from formats

Use pr_fmt to prefix KBUILD_MODNAME to appropriate logging messages.

Remove now unnecessary internal prefixes from formats.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: Convert printks to pr_<level>
Joe Perches [Wed, 15 Feb 2012 23:56:44 +0000 (15:56 -0800)]
jffs2: Convert printks to pr_<level>

Use the more current logging style.

Coalesce formats, align arguments.
Convert uses of embedded function names to %s, __func__.

A couple of long line checkpatch errors I don't care about exist.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: Convert most D1/D2 macros to jffs2_dbg
Joe Perches [Wed, 15 Feb 2012 23:56:43 +0000 (15:56 -0800)]
jffs2: Convert most D1/D2 macros to jffs2_dbg

D1 and D2 macros are mostly uses to emit debugging messages.

Convert the logging uses of D1 & D2 to jffs2_dbg(level, fmt, ...)
to be a bit more consistent style with the rest of the kernel.

All jffs2_dbg output is now at KERN_DEBUG where some of
the previous uses were emitted at various KERN_<LEVEL>s.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: mips: lantiq: reintroduce support for cmdline partitions
Daniel Schwierzeck [Thu, 23 Feb 2012 16:59:49 +0000 (17:59 +0100)]
mtd: mips: lantiq: reintroduce support for cmdline partitions

Since commit ca97dec2ab5c87e9fbdf7e882e1820004a3966fa the
command line parsing of MTD partitions does not work anymore.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: change the location of the ONFI detected log
Huang Shijie [Fri, 17 Feb 2012 03:22:37 +0000 (11:22 +0800)]
mtd: change the location of the ONFI detected log

Some strange nand chip(such as Hynix H27UBG8T2A) can pass the `ONFI` signature
check. So the log can be printed out even it is not an ONFI nand indeed.

Change this log to the end of the function. Print out the log only when we
really detect an ONFI nand.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomxs-dma : rewrite the last parameter of mxs_dma_prep_slave_sg()
Huang Shijie [Thu, 16 Feb 2012 06:17:33 +0000 (14:17 +0800)]
mxs-dma : rewrite the last parameter of mxs_dma_prep_slave_sg()

[1] Background :
    The GPMI does ECC read page operation with a DMA chain consist of three DMA
    Command Structures. The middle one of the chain is used to enable the BCH,
    and read out the NAND page.

    The WAIT4END(wait for command end) is a comunication signal between
    the GPMI and MXS-DMA.

[2] The current DMA code sets the WAIT4END bit at the last one, such as:

    +-----+               +-----+                      +-----+
    | cmd | ------------> | cmd | ------------------>  | cmd |
    +-----+               +-----+                      +-----+
                                                          ^
                                                          |
                                                          |
                                                     set WAIT4END here

    This chain works fine in the mx23/mx28.

[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
    be set not only at the last DMA Command Structure,
    but also at the middle one, such as:

    +-----+               +-----+                      +-----+
    | cmd | ------------> | cmd | ------------------>  | cmd |
    +-----+               +-----+                      +-----+
                             ^                            ^
                             |                            |
                             |                            |
                        set WAIT4END here too        set WAIT4END here

    If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state.
    In the next ECC write page operation, a DMA-timeout occurs.
    This has been catched in the MX6Q board.

[4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(),
    and use the dma_ctrl_flags:
    ---------------------------------------------------------
      DMA_PREP_INTERRUPT : append a new DMA Command Structrue.
      DMA_CTRL_ACK       : set the WAIT4END bit for this DMA Command Structure.
    ---------------------------------------------------------

[5] changes to the relative drivers:
    <1> For mxs-mmc driver, just use the new flags, do not change any logic.
    <2> For gpmi-nand driver, and use the new flags to set the DMA
        chain, especially for ecc read page.

Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomxs-dma : move the mxs dma.h to a more common place
Huang Shijie [Thu, 16 Feb 2012 06:17:32 +0000 (14:17 +0800)]
mxs-dma : move the mxs dma.h to a more common place

Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q.  It will also be used in the future chips.

Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.

change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.

Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: make jffs2_initxattrs() static
Nikola Pajkovsky [Sun, 19 Feb 2012 18:51:42 +0000 (19:51 +0100)]
jffs2: make jffs2_initxattrs() static

Signed-off-by: Nikola Pajkovsky <n.pajkovsky@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: fix 'Flash device refused suspend due to active operation' message
Russell King [Wed, 15 Feb 2012 11:48:34 +0000 (11:48 +0000)]
mtd: fix 'Flash device refused suspend due to active operation' message

While debugging on SA11x0, the following message was observed:

"Flash device refused suspend due to active operation (state 20)"

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: gpmi: fix compiler warning
Huang Shijie [Tue, 14 Feb 2012 03:22:04 +0000 (11:22 +0800)]
mtd: gpmi: fix compiler warning

The gpmi driver selects the MTD_CMDLINE_PARTS directly.
But we should not select a visible symbol.

Just remove the select.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: simplify return logic in do_map_probe()
Uwe Kleine-König [Mon, 13 Feb 2012 15:12:24 +0000 (16:12 +0100)]
mtd: simplify return logic in do_map_probe()

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agosfc: mtd: Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffff
Shmulik Ladkani [Sun, 12 Feb 2012 09:13:08 +0000 (11:13 +0200)]
sfc: mtd: Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffff

As of bb0eb217, MTD_FAIL_ADDR_UNKNOWN should be used to indicate mtd
erase failure not specific to any particular block.

Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffff when setting
'erase->fail_addr' in 'efx_mtd_erase()'.

Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: Fix typo in compr.c
Masanari Iida [Wed, 8 Feb 2012 11:39:39 +0000 (20:39 +0900)]
jffs2: Fix typo in compr.c

Correct spelling "modul" to "module" in
fs/hffs2/compr.c

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: ixp4xx: oops in ixp4xx_flash_probe
Marc Kleine-Budde [Wed, 8 Feb 2012 19:24:29 +0000 (20:24 +0100)]
mtd: ixp4xx: oops in ixp4xx_flash_probe

In commit "c797533 mtd: abstract last MTD partition parser argument" the
third argument of "mtd_device_parse_register()" changed from start address
of the MTD device to a pointer to a struct.

The "ixp4xx_flash_probe()" function was not converted properly, causing
an oops during boot.

This patch fixes the problem by filling the needed information into a
"struct mtd_part_parser_data" and passing it to
"mtd_device_parse_register()".

Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: check for zero length in OTP functions
Artem Bityutskiy [Wed, 8 Feb 2012 14:37:14 +0000 (16:37 +0200)]
mtd: check for zero length in OTP functions

This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.

This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: move zero length verification to MTD API functions
Artem Bityutskiy [Mon, 6 Feb 2012 11:27:43 +0000 (13:27 +0200)]
mtd: move zero length verification to MTD API functions

In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: harmonize mtd_point interface implementation
Artem Bityutskiy [Wed, 8 Feb 2012 13:13:26 +0000 (15:13 +0200)]
mtd: harmonize mtd_point interface implementation

Some MTD drivers return -EINVAL if the 'phys' parameter is not NULL, trying to
convey that they cannot return the physical address. However, this is not very
logical because they still can return the virtual address ('virt'). But some
drivers (lpddr) just ignore the 'phys' parameter instead, which is a more
logical thing to do.

Let's harmonize this and:

1. Always initialize 'virt' and 'phys' to 'NULL' in 'mtd_point()'.
2. Do not return an error if the physical address cannot be found.

So as a result, all drivers will set 'phys' to 'NULL' if it is not supported.
None of the 'mtd_point()' users use 'phys' anyway, so this should not break
anything. I guess we could also just delete this parameter later.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: remove junk pmc551.h
Artem Bityutskiy [Mon, 6 Feb 2012 11:44:27 +0000 (13:44 +0200)]
mtd: remove junk pmc551.h

This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: remove retlen zeroing duplication
Artem Bityutskiy [Mon, 6 Feb 2012 10:39:07 +0000 (12:39 +0200)]
mtd: remove retlen zeroing duplication

The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:

    'mtd_point()'
    'mtd_read()'
    'mtd_write()'
    'mtd_writev()'
    'mtd_panic_write()'

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: remove R/O checking duplication
Artem Bityutskiy [Fri, 3 Feb 2012 16:13:23 +0000 (18:13 +0200)]
mtd: remove R/O checking duplication

Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.

And again a bit of noise - deleted few too sparse newlines, sorry.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: do not duplicate length and offset checks in drivers
Artem Bityutskiy [Fri, 3 Feb 2012 14:23:52 +0000 (16:23 +0200)]
mtd: do not duplicate length and offset checks in drivers

We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:

'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'

This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: add offset and length checks to the API function
Artem Bityutskiy [Fri, 3 Feb 2012 12:34:14 +0000 (14:34 +0200)]
mtd: add offset and length checks to the API function

Add verification of the offset and length to MTD API functions and verify that
MTD device offset and length are within MTD device size.

The modified API functions are:

'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'

This patch also uninlines these functions and exports in mtdcore.c because they
are not performance-critical and do not have to be inlined.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: return error code from mtd_unpoint
Artem Bityutskiy [Fri, 3 Feb 2012 11:20:43 +0000 (13:20 +0200)]
mtd: return error code from mtd_unpoint

The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.

Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: write BBM to OOB even with flash-based BBT
Brian Norris [Mon, 6 Feb 2012 21:44:00 +0000 (13:44 -0800)]
mtd: nand: write BBM to OOB even with flash-based BBT

Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:

 * bootloader cannot read the flash-based BBT format
 * BBT is corrupted and the flash must be rescanned for bad
   blocks; we want to remember bad blocks that were marked from Linux

So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.

The new flash-based BBT procedure for marking bad blocks:
 (1) erase the affected block, to allow OOB marker to be written cleanly
 (2) update in-memory BBT
 (3) write bad block marker to OOB area of affected block
 (4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.

This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.

Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: redboot: remove useless code
Artem Bityutskiy [Fri, 3 Feb 2012 09:37:47 +0000 (11:37 +0200)]
mtd: redboot: remove useless code

We do not need to invoke 'mtd_can_have_bb()' before invoking
'mtd_block_isbad()' because the latter already handles the case when the MTD
device does not support bad blocks.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nftlcore: remove out-of-date and now irrelevant piece of code
Artem Bityutskiy [Fri, 3 Feb 2012 09:35:59 +0000 (11:35 +0200)]
mtd: nftlcore: remove out-of-date and now irrelevant piece of code

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtdoops: clean-up new MTD API usage
Artem Bityutskiy [Fri, 3 Feb 2012 09:23:57 +0000 (11:23 +0200)]
mtdoops: clean-up new MTD API usage

Let's remove useless 'mtd_can_have_bb()' function invocations.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: mtdconcat: return -EOPNOTSUPP if block_markbad is undefined
Artem Bityutskiy [Fri, 3 Feb 2012 09:03:28 +0000 (11:03 +0200)]
mtd: mtdconcat: return -EOPNOTSUPP if block_markbad is undefined

The main 'mtd_block_markbad()' function returns -EOPNOTSUPP if the
'->block_markbad' method is undefined, and mtdconcat should do the same.
Fix this by simply removing the 'mtd_can_have_bb()' because it is  not
really necessary. It could be treated as an optimization, but this function is
expected to be used so rarely that it does not matter.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sst25l: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 08:16:50 +0000 (10:16 +0200)]
mtd: sst25l: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: spear_smi: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 08:14:12 +0000 (10:14 +0200)]
mtd: spear_smi: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: lart: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 07:53:28 +0000 (09:53 +0200)]
mtd: lart: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set writebufsize to 4 because this drivers writes at max 4 bytes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: docg3: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 07:44:32 +0000 (09:44 +0200)]
mtd: docg3: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: doc2001plus: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 07:43:14 +0000 (09:43 +0200)]
mtd: doc2001plus: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: doc2001: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 07:42:39 +0000 (09:42 +0200)]
mtd: doc2001: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: doc2000: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 07:38:43 +0000 (09:38 +0200)]
mtd: doc2000: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: block2mtd: initialize writebufsize
Artem Bityutskiy [Fri, 3 Feb 2012 07:32:44 +0000 (09:32 +0200)]
mtd: block2mtd: initialize writebufsize

The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE
because this is actually the amount of data we write at a time.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: Remove unnecessary OOM messages
Joe Perches [Tue, 31 Jan 2012 22:42:08 +0000 (14:42 -0800)]
jffs2: Remove unnecessary OOM messages

Per call site OOM messages are unnecessary.
k.alloc and v.alloc failures use dump_stack().

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: docg4: fix printk() warnings
Dan Carpenter [Tue, 31 Jan 2012 08:54:06 +0000 (11:54 +0300)]
mtd: docg4: fix printk() warnings

Gcc complains here:
drivers/mtd/nand/docg4.c: In function ‘probe_docg4’:
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘resource_size_t’ [-Wformat]
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘resource_size_t’ [-Wformat]

We have a standard way of printing these using a format string
extension.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: gpmi: use correct member for checking NAND_BBT_USE_FLASH
Wolfram Sang [Tue, 31 Jan 2012 12:10:43 +0000 (13:10 +0100)]
mtd: nand: gpmi: use correct member for checking NAND_BBT_USE_FLASH

This has been moved from .options to .bbt_options meanwhile. So, it
currently checks for something totally different (NAND_OWN_BUFFERS) and
decides according to that.

Artem Bityutskiy: the options were moved in
a40f734 mtd: nand: consolidate redundant flash-based BBT flags

Artem Bityutskiy: CCing -stable

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: m25p80: set writebufsize
Brian Norris [Tue, 31 Jan 2012 08:06:03 +0000 (00:06 -0800)]
mtd: m25p80: set writebufsize

Using UBI on m25p80 can give messages like:

    UBI error: io_init: bad write buffer size 0 for 1 min. I/O unit

We need to initialize writebufsize; I think "page_size" is the correct
"bufsize", although I'm not sure. Comments?

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: mtdcore: remove unnecessary mtd->resume check
Brian Norris [Fri, 27 Jan 2012 20:39:32 +0000 (12:39 -0800)]
mtd: mtdcore: remove unnecessary mtd->resume check

We don't need to to check for mtd->resume before calling mtd_resume().
mtd_resume() should take care of that.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: fix typo in scan.c
Masanari Iida [Fri, 27 Jan 2012 15:17:28 +0000 (00:17 +0900)]
jffs2: fix typo in scan.c

Correct spelling "scaning" to scanning" in
fs/jffs2/scan.c

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: add leading underscore to all mtd functions
Artem Bityutskiy [Mon, 30 Jan 2012 12:58:32 +0000 (14:58 +0200)]
mtd: add leading underscore to all mtd functions

This patch renames all MTD functions by adding a "_" prefix:

mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...

The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:

1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
   less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
   spot the big API change and amend them.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: update to new MTD interface
Brian Norris [Fri, 3 Feb 2012 00:21:09 +0000 (16:21 -0800)]
jffs2: update to new MTD interface

There were a few instances of the old MTD interface remaining for JFFS2. We
fix one error that shows up (only when CONFIG_JFFS2_FS_WRITEBUFFER is not
defined) like this:

  fs/jffs2/read.c: In function 'jffs2_read_dnode':
  fs/jffs2/read.c:36:8: error: 'struct mtd_info' has no member named 'read'
  fs/jffs2/read.c:112:8: error: 'struct mtd_info' has no member named 'read'
  ...

We also simply remove two macros that are not in use, were not updated to
the new MTD interface, and don't even utilize the old interface properly.
(That means they weren't used since commit 8593fbc6, year 2006; almost 6
years ago, for those who don't want to do the math)

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agoromfs: switch to new MTD API
Artem Bityutskiy [Mon, 30 Jan 2012 13:11:44 +0000 (15:11 +0200)]
romfs: switch to new MTD API

We have changed the MTD API and now ROMFS should use 'mtd_read()' instead
of mtd->read().

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agojffs2: remove direct mtd->point reference
Artem Bityutskiy [Mon, 30 Jan 2012 13:08:26 +0000 (15:08 +0200)]
jffs2: remove direct mtd->point reference

Commit 10934478e44d9a5a7b16dadd89094fb608cf101e did not remove now useless
"if (mtd->point)" check mistakingly - let's kill it now.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: add support for diskonchip G4 nand flash device
Mike Dunn [Wed, 4 Jan 2012 00:05:44 +0000 (16:05 -0800)]
mtd: nand: add support for diskonchip G4 nand flash device

This patch adds a driver for the M-Sys / Sandisk diskonchip G4 nand flash found
in various smartphones and PDAs, among them the Palm Treo680, HTC Prophet and
Wizard, Toshiba Portege G900, Asus P526, and O2 XDA Zinc.  It was tested on the
Treo 680, but should work generically.

Since v3, this patch adds power management functions, a scan of the factory bad
block table during initialization, several fixes, and more extensive testing.
Also, the platform data header file, which only contained partitioning
information, was removed.  Command-line partitioning can be used, at least until
an mtd parser is written for the saftl format with which these chips are
shipped.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: minor coding style cleanup in mtdpart.c
Stefan Roese [Wed, 25 Jan 2012 10:24:36 +0000 (11:24 +0100)]
mtd: minor coding style cleanup in mtdpart.c

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: convert drivers/mtd/* to use module_spi_driver()
Axel Lin [Fri, 27 Jan 2012 07:45:20 +0000 (15:45 +0800)]
mtd: convert drivers/mtd/* to use module_spi_driver()

This patch converts the drivers in drivers/mtd/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: move SCANLASTPAGE handling to the correct code block
Brian Norris [Sat, 21 Jan 2012 04:38:03 +0000 (20:38 -0800)]
mtd: nand: move SCANLASTPAGE handling to the correct code block

As nand_default_block_markbad() is becoming more complex, it helps to
have code appear only in its relevant codepath(s). Here, the calculation
of `ofs' based on NAND_BBT_SCANLASTPAGE is only useful on paths where we
write bad block markers to OOB. We move the condition/calculation closer
to the `write' operation and update the comment to more correctly
describe the operation.

The variable `wr_ofs' is also used to help isolate our calculation of
the "write" offset from the usage of `ofs' to represent the eraseblock
offset. This will become useful when we reorder operations in the next
patch.

This patch should make no functional change.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: mtdoops: kill Kconfig usage instructions
Brian Norris [Fri, 20 Jan 2012 21:17:00 +0000 (13:17 -0800)]
mtd: mtdoops: kill Kconfig usage instructions

The mtdoops usage instructions found in Kconfig have been incorrect
since:

    commit 2e386e4bac90554887e73d6f342e845185b33fc3
    mtd: mtdoops: refactor as a kmsg_dumper

mtdoops no longer uses a console. Now, if you build it into your kernel,
you add something like the following to your command line to select
partition X as your logging partition:

    mtdoops.mtddev=X

Anyway, it seems better to leave the documentation out of Kconfig.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sa11x0: remove definitions and code left for documentation purposes
Russell King - ARM Linux [Fri, 20 Jan 2012 10:42:36 +0000 (10:42 +0000)]
mtd: sa11x0: remove definitions and code left for documentation purposes

/*
 * This is here for documentation purposes only - until these people
 * submit their machine types.  It will be gone January 2005.
 */

It's now seven years after that date, so let's remove this.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: sa11x0: Remove shutdown handler
Russell King - ARM Linux [Fri, 20 Jan 2012 10:42:16 +0000 (10:42 +0000)]
mtd: sa11x0: Remove shutdown handler

Commit c4a9f88daf ([MTD] [NOR] fix ctrl-alt-del can't reboot for
intel flash bug) interferes with this work-around, causing MTD to
issue this warning:

Flash device refused suspend due to active operation (state 0)

The commit makes our work-around in the map driver unnecessary, so
let's remove it.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: spear_smi: release memory region during remove
Shiraz Hashim [Fri, 20 Jan 2012 10:35:19 +0000 (11:35 +0100)]
mtd: spear_smi: release memory region during remove

Driver must cleanup all held resources during remove. It wasn't
releasing requested memory region.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: ST SPEAr: Add SMI driver for serial NOR flash
Shiraz Hashim [Thu, 12 Jan 2012 13:38:57 +0000 (14:38 +0100)]
mtd: ST SPEAr: Add SMI driver for serial NOR flash

SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: correct comment on nand_chip badblockbits
Brian Norris [Sat, 14 Jan 2012 02:11:50 +0000 (18:11 -0800)]
mtd: nand: correct comment on nand_chip badblockbits

The description for badblockbits is incorrect. I think someone just made
up a false description on the spot to satisfy some kerneldoc warning.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: differentiate 1- vs. 2-byte writes when marking bad blocks
Brian Norris [Sat, 14 Jan 2012 02:11:49 +0000 (18:11 -0800)]
mtd: nand: differentiate 1- vs. 2-byte writes when marking bad blocks

It seems that we have developed a bad-block-marking "feature" out of
pure laziness:

  "We write two bytes per location, so we dont have to mess with 16 bit
  access."

It's relatively simple to write a 1 byte at a time on x8 devices and 2
bytes at a time on x16 devices, so let's do it.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: fix SCAN2NDPAGE check for BBM
Brian Norris [Sat, 14 Jan 2012 02:11:48 +0000 (18:11 -0800)]
mtd: nand: fix SCAN2NDPAGE check for BBM

nand_block_bad() doesn't check the correct pages when
NAND_BBT_SCAN2NDPAGE is enabled. It should scan both the OOB region of
both the 1st and 2nd page of each block.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: nand: erase block before marking bad
Brian Norris [Sat, 14 Jan 2012 02:11:47 +0000 (18:11 -0800)]
mtd: nand: erase block before marking bad

Many NAND flash systems (especially those with MLC NAND) cannot be
reliably written twice in a row. For instance, when marking a bad block,
the block may already have data written to it, and so we should attempt
to erase the block before writing a bad block marker to its OOB region.

We can ignore erase failures, since the block may be bad such that it
cannot be erased properly; we still attempt to write zeros to its spare
area.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: onenand: samsung: add missing iounmap
Julia Lawall [Thu, 12 Jan 2012 09:55:05 +0000 (10:55 +0100)]
mtd: onenand: samsung: add missing iounmap

Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
    when != iounmap(e)
*if (...)
   { ... when != iounmap(e)
     return ...; }
... when any
iounmap(e);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: mtdcore: Fix build warning when CONFIG_MTD_CHAR is not defined
Fabio Estevam [Thu, 12 Jan 2012 03:25:04 +0000 (01:25 -0200)]
mtd: mtdcore: Fix build warning when CONFIG_MTD_CHAR is not defined

Fix the following build warning:

drivers/mtd/mtdcore.c: In function ‘mtd_release’:
drivers/mtd/mtdcore.c:110: warning: unused variable ‘mtd’

This happens when neither CONFIG_MTD_CHAR nor CONFIG_MTD_CHAR_MODULE are defined.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: mtdblock: call mtd_sync() only if opened for write
Alexander Stein [Tue, 10 Jan 2012 12:26:58 +0000 (13:26 +0100)]
mtd: mtdblock: call mtd_sync() only if opened for write

Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.

Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: pmc551: fix signedness bug in init_pmc551()
Xi Wang [Mon, 9 Jan 2012 21:58:25 +0000 (16:58 -0500)]
mtd: pmc551: fix signedness bug in init_pmc551()

Since "length" is a u32, the error handling below didn't work when
fixup_pmc551() returns -ENODEV.

if ((length = fixup_pmc551(PCI_Device)) <= 0)

This patch changes both the type of "length" and the return type of
fixup_pmc551() to int.

Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agomtd: cfi: AMD/Fujitsu compatibles: add panic write support
Ira W. Snyder [Fri, 6 Jan 2012 19:29:19 +0000 (11:29 -0800)]
mtd: cfi: AMD/Fujitsu compatibles: add panic write support

This allows the mtdoops driver to work on flash chips using the
AMD/Fujitsu compatible command set.

As the code comments note, the locks used throughout the normal code
paths in the driver are ignored, so that the chance of writing out the
kernel's last messages are maximized.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
12 years agoLinux 3.3-rc6
Linus Torvalds [Sun, 4 Mar 2012 01:08:09 +0000 (17:08 -0800)]
Linux 3.3-rc6

12 years agoMerge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi...
Linus Torvalds [Sun, 4 Mar 2012 00:42:30 +0000 (16:42 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

SCSI fixes from James Bottomley:
 "There's just a single fix in here: the osd max device number fix."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] osd_uld: Bump MAX_OSD_DEVICES from 64 to 1,048,576

12 years agoMerge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Linus Torvalds [Sun, 4 Mar 2012 00:33:51 +0000 (16:33 -0800)]
Merge tag 'parisc-fixes' of git://git./linux/kernel/git/jejb/parisc-2.6

PARISC fixes from James Bottomley:
 "This is a set of build fixes to get the cross compiled architecture
  testbeds building again"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] don't unconditionally override CROSS_COMPILE for 64 bit.
  [PARISC] include <linux/prefetch.h> in drivers/parisc/iommu-helpers.h
  [PARISC] fix compile break caused by iomap: make IOPORT/PCI mapping functions conditional

12 years agoMerge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Sat, 3 Mar 2012 17:32:31 +0000 (09:32 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled

12 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Linus Torvalds [Sat, 3 Mar 2012 17:31:49 +0000 (09:31 -0800)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6

Pull from Herbert Xu:
  "This push fixes a bug in mv_cesa that causes all hash operations
   that supply data on a final operation to fail."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: mv_cesa - fix final callback not ignoring input data

12 years agovfs: export full_name_hash() function to modules
Linus Torvalds [Sat, 3 Mar 2012 03:40:57 +0000 (19:40 -0800)]
vfs: export full_name_hash() function to modules

Commit 5707c87f "vfs: uninline full_name_hash()" broke the modular
build, because it needs exporting now that it isn't inlined any more.

Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agoMerge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck...
Linus Torvalds [Fri, 2 Mar 2012 23:21:48 +0000 (15:21 -0800)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging

hhwmon fixes for 3.3-rc6 from Guenter Roeck:

These patches are necessary for correct operation and management of
F75387.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (f75375s) Catch some attempts to write to r/o registers
  hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
  hwmon: (f75375s) Make pwm*_mode writable for the F75387
  hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387

12 years agoMerge tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6
Linus Torvalds [Fri, 2 Mar 2012 23:21:15 +0000 (15:21 -0800)]
Merge tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6

fbdev fixes for 3.3 from Florian Tobias Schandinat

It includes:
 - two fixes for OMAP HDMI
 - one fix to make new OMAP functions behave as they are supposed to
 - one Kconfig dependency fix
 - two fixes for viafb for modesetting on VX900 hardware

* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
  OMAPDSS: APPLY: make ovl_enable/disable synchronous
  OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
  viafb: fix IGA1 modesetting on VX900
  viafb: select HW scaling on VX900 for IGA2
  OMAPDSS: HDMI: hot plug detect fix
  OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled

12 years agoMerge tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Linus Torvalds [Fri, 2 Mar 2012 23:20:41 +0000 (15:20 -0800)]
Merge tag 'sound-fixes' of git://git./linux/kernel/git/tiwai/sound

sound fixes for 3.3-rc6 from Takashi Iwai

This contains again regression fixes for various HD-audio and ASoC
regarding SSI and dapm shutdown path.  In addition, a minor azt3328
fix and the correction of the new jack-notification strings in HD-audio.

* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Kill hyphenated names
  ALSA: hda - Add a fake mute feature
  ALSA: hda - Always set HP pin in unsol handler for STAC/IDT codecs
  ALSA: azt3328 - Fix NULL ptr dereference on cards without OPL3
  ALSA: hda/realtek - Fix resume of multiple input sources
  ASoC: i.MX SSI: Fix DSP_A format.
  ASoC: dapm: Check for bias level when powering down

12 years agovfs: split up name hashing in link_path_walk() into helper function
Linus Torvalds [Fri, 2 Mar 2012 22:49:24 +0000 (14:49 -0800)]
vfs: split up name hashing in link_path_walk() into helper function

The code in link_path_walk() that finds out the length and the hash of
the next path component is some of the hottest code in the kernel.  And
I have a version of it that does things at the full width of the CPU
wordsize at a time, but that means that we *really* want to split it up
into a separate helper function.

So this re-organizes the code a bit and splits the hashing part into a
helper function called "hash_name()".  It returns the length of the
pathname component, while at the same time computing and writing the
hash to the appropriate location.

The code generation is slightly changed by this patch, but generally for
the better - and the added abstraction actually makes the code easier to
read too.  And the new interface is well suited for replacing just the
"hash_name()" function with alternative implementations.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agovfs: clarify and clean up dentry_cmp()
Linus Torvalds [Fri, 2 Mar 2012 22:47:15 +0000 (14:47 -0800)]
vfs: clarify and clean up dentry_cmp()

It did some odd things for unclear reasons.  As this is one of the
functions that gets changed when doing word-at-a-time compares, this is
yet another of the "don't change any semantics, but clean things up so
that subsequent patches don't get obscured by the cleanups".

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agovfs: uninline full_name_hash()
Linus Torvalds [Fri, 2 Mar 2012 22:32:59 +0000 (14:32 -0800)]
vfs: uninline full_name_hash()

.. and also use it in lookup_one_len() rather than open-coding it.

There aren't any performance-critical users, so inlining it is silly.
But it wouldn't matter if it wasn't for the fact that the word-at-a-time
dentry name patches want to conditionally replace the function, and
uninlining it sets the stage for that.

So again, this is a preparatory patch that doesn't change any semantics,
and only prepares for a much cleaner and testable word-at-a-time dentry
name accessor patch.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agovfs: trivial __d_lookup_rcu() cleanups
Linus Torvalds [Fri, 2 Mar 2012 22:23:30 +0000 (14:23 -0800)]
vfs: trivial __d_lookup_rcu() cleanups

These don't change any semantics, but they clean up the code a bit and
mark some arguments appropriately 'const'.

They came up as I was doing the word-at-a-time dcache name accessor
code, and cleaning this up now allows me to send out a smaller relevant
interesting patch for the experimental stuff.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agohwmon: (f75375s) Catch some attempts to write to r/o registers
Nikolaus Schulz [Tue, 28 Feb 2012 21:15:54 +0000 (16:15 -0500)]
hwmon: (f75375s) Catch some attempts to write to r/o registers

It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode.  The corresponding
registers are then read-only.  If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.

Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
12 years agohwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
Nikolaus Schulz [Tue, 28 Feb 2012 21:15:53 +0000 (16:15 -0500)]
hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable

The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values.  Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.

The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.

Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.

This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.

Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
12 years agoMerge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and 'sched-urgent...
Linus Torvalds [Fri, 2 Mar 2012 19:38:43 +0000 (11:38 -0800)]
Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pulling latest branches from Ingo:

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  memblock: Fix size aligning of memblock_alloc_base_nid()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf probe: Ensure offset provided is not greater than function length without DWARF info too
  perf tools: Ensure comm string is properly terminated
  perf probe: Ensure offset provided is not greater than function length
  perf evlist: Return first evsel for non-sample event on old kernel
  perf/hwbp: Fix a possible memory leak

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  CPU hotplug, cpusets, suspend: Don't touch cpusets during suspend/resume

12 years agoregset: Return -EFAULT, not -EIO, on host-side memory fault
H. Peter Anvin [Fri, 2 Mar 2012 18:43:49 +0000 (10:43 -0800)]
regset: Return -EFAULT, not -EIO, on host-side memory fault

There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT.  Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.

Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agoregset: Prevent null pointer reference on readonly regsets
H. Peter Anvin [Fri, 2 Mar 2012 18:43:48 +0000 (10:43 -0800)]
regset: Prevent null pointer reference on readonly regsets

The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.

Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.

Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
12 years agoperf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled
Joerg Roedel [Wed, 29 Feb 2012 13:57:32 +0000 (14:57 +0100)]
perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled

It turned out that a performance counter on AMD does not
count at all when the GO or HO bit is set in the control
register and SVM is disabled in EFER.

This patch works around this issue by masking out the HO bit
in the performance counter control register when SVM is not
enabled.

The GO bit is not touched because it is only set when the
user wants to count in guest-mode only. So when SVM is
disabled the counter should not run at all and the
not-counting is the intended behaviour.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: stable@vger.kernel.org # v3.2
Link: http://lkml.kernel.org/r/1330523852-19566-1-git-send-email-joerg.roedel@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
12 years agoALSA: hda - Kill hyphenated names
Takashi Iwai [Thu, 1 Mar 2012 17:14:41 +0000 (18:14 +0100)]
ALSA: hda - Kill hyphenated names

Kill hyphens from "Line-Out" name strings, as suggested by Mark Brown.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
12 years agoMerge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git...
Ingo Molnar [Fri, 2 Mar 2012 07:40:45 +0000 (08:40 +0100)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent

Various smaller perf/urgent fixes.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
12 years agoMerge git://www.linux-watchdog.org/linux-watchdog
Linus Torvalds [Fri, 2 Mar 2012 02:27:43 +0000 (18:27 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog

Watchdog updates from Wim Van Sebroeck:

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: fix GETTIMEOUT ioctl in booke_wdt
  watchdog: update maintainers git entry
  watchdog: Fix typo in pnx4008_wdt.c
  watchdog: Fix typo in Kconfig
  watchdog: fix error in probe() of s3c2410_wdt (reset at booting)
  watchdog: hpwdt: clean up set_memory_x call for 32 bit

12 years agoMerge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Linus Torvalds [Fri, 2 Mar 2012 02:26:48 +0000 (18:26 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/broonie/regulator

Pull from Mark Brown:
 "A simple, driver specific fix.  This device isn't widely used outside
  of Marvell reference boards most of which are probably used with their
  BSPs rather than with mainline so low risk."

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: fix the ldo configure according to 88pm860x spec