qeth: synchronize configuration interface

Synchronize access to the drivers configuration interface.
Also do not allow configuration changes during online/offline
transition.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: new message if OLM limit is reached

z/OS may activate Optimized Latency Mode (OLM) for a connection
through an OSA Express3 adapter, which reduces the number of
allowed concurrent connections, if adapter is used in shared mode.
Create a meaningful message, if activation of an OSA-connection fails
due to an active OLM-connection on the shared OSA-adapter.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth: exploit HW TX checksumming

OSA supports HW TX checksumming in layer 3 mode. Enable this
feature and remove software fallback used for TSO. Cleanup
checksum bits to indicate OSA can do checksumming only for
IPv4 TCP and UDP.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: congestion notifications are not dropped packets

vlan/macvlan start_xmit() can inform caller of congestion with
NET_XMIT_CN return value. This doesnt mean packet was dropped.
Increment normal stat counters instead of tx_dropped.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Introduce sk_route_nocaps

TCP-MD5 sessions have intermittent failures, when route cache is
invalidated. ip_queue_xmit() has to find a new route, calls
sk_setup_caps(sk, &rt->u.dst), destroying the

sk->sk_route_caps &= ~NETIF_F_GSO_MASK

that MD5 desperately try to make all over its way (from
tcp_transmit_skb() for example)

So we send few bad packets, and everything is fine when
tcp_transmit_skb() is called again for this socket.

Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a
socket field, sk_route_nocaps, containing bits to mask on sk_route_caps.

Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Consistent skb timestamping

With RPS inclusion, skb timestamping is not consistent in RX path.

If netif_receive_skb() is used, its deferred after RPS dispatch.

If netif_rx() is used, its done before RPS dispatch.

This can give strange tcpdump timestamps results.

I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)

Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.

Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue

Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.

Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm: fix policy unreferencing on larval drop

I mistakenly had the error path to use num_pols to decide how
many policies we need to drop (cruft from earlier patch set
version which did not handle socket policies right).

This is wrong since normally we do not keep explicit references
(instead we hold reference to the cache entry which holds references
to policies). drop_pols is set to num_pols if we are holding the
references, so use that. Otherwise we eventually BUG_ON inside
xfrm_policy_destroy due to premature policy deletion.

Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: adjust handle_macvlan to pass port struct to hook

Now there's null check here and also again in the hook. Looking at bridge bits
which are simmilar, port structure is rcu_dereferenced right away in
handle_bridge and passed to hook. Looks nicer.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

skge: use the DMA state API instead of the pci equivalents

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: reserve ports for applications using fixed port numbers

(Dropped the infiniband part, because Tetsuo modified the related code,
I will send a separate patch for it once this is accepted.)

This patch introduces /proc/sys/net/ipv4/ip_local_reserved_ports which
allows users to reserve ports for third-party applications.

The reserved ports will not be used by automatic port assignments
(e.g. when calling connect() or bind() with port number 0). Explicit
port allocation behavior is unchanged.

Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sysctl: add proc_do_large_bitmap

The new function can be used to read/write large bitmaps via /proc. A
comma separated range format is used for compact output and input
(e.g. 1,3-4,10-10).

Writing into the file will first reset the bitmap then update it
based on the given input.

Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sysctl: refactor integer handling proc code

(Based on Octavian's work, and I modified a lot.)

As we are about to add another integer handling proc function a little
bit of cleanup is in order: add a few helper functions to improve code
readability and decrease code duplication.

In the process a bug is also fixed: if the user specifies a number
with more then 20 digits it will be interpreted as two integers
(e.g. 10000...13 will be interpreted as 100.... and 13).

Behavior for EFAULT handling was changed as well. Previous to this
patch, when an EFAULT error occurred in the middle of a write
operation, although some of the elements were set, that was not
acknowledged to the user (by shorting the write and returning the
number of bytes accepted). EFAULT is now treated just like any other
errors by acknowledging the amount of bytes accepted.

Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/inaky/wimax

bridge: update sysfs link names if port device names have changed

Links for each port are created in sysfs using the device
name, but this could be changed after being added to the
bridge.

As well as being unable to remove interfaces after this
occurs (because userspace tools don't recognise the new
name, and the kernel won't recognise the old name), adding
another interface with the old name to the bridge will
cause an error trying to create the sysfs link.

This fixes the problem by listening for NETDEV_CHANGENAME
notifications and renaming the link.

https://bugzilla.kernel.org/show_bug.cgi?id=12743

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: change console message interface

Use one set of macro's for all bridge messages.

Note: can't use netdev_XXX macro's because bridge is purely
virtual and has no device parent.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: netpoll cleanup

Move code around so that the ifdef for NETPOLL_CONTROLLER don't have to
show up in main code path. The control functions should be in helpers
that are only compiled if needed.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rndis_host: Poll status channel before control channel

Some RNDIS devices don't respond on the control channel until polled
on the status channel.  In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW.

This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is reported to be needed for use with some Windows Mobile devices
and which is currently applied by Mandriva.

Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: xt_TEE depends on NF_CONNTRACK

Fix xt_TEE build for the case of NF_CONNTRACK=m and
NETFILTER_XT_TARGET_TEE=y:

xt_TEE.c:(.text+0x6df5c): undefined reference to `nf_conntrack_untracked'
4x

Built with all 4 m/y combinations.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: add idc debug registers

When ever driver changes the device state, it should write
pci-func number and timestamp in debug registers.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: support quisce mode

Device can go to quiescent state, during which drivers
should refrain from using the device.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: check device class

pci-func class can be other than ethernet in Qlogic CNA device.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: check IDC version

Warn user if IDC version mismatch with different class of drivers.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: cleanup unused code

LRO ring, cut-thru mode and specific fw version are not
valid to Qlogic CNA device.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: cleanup dma mask setting

Device support 64 bit dma mask.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix caching window register

o Window register is not per pci-func, so caching can
result in expected result.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: remove obsolete register

MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete.
Driver should not use them.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: fix context cleanup

Before going for recovery, every pci-func should check fw state,
irrespective of device state. This to avoid unnecssary sending
of command for ctx destroy.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: version 1.28

Version 1.28

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Avoid allocating memory in sky2_resume

Allocating memory can fail, and since we have the memory we need
in sky2_resume when sky2_suspend is called, just stop the hardware
without freeing the memory it's using.

This avoids the possibility of failing because we can't allocate
memory in sky2_resume(), and allows sharing code with sky2_restart().

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Refactor down/up code out of sky2_restart()

Code to bring down all sky2 interfaces and bring it up
again can be reused in sky2_suspend and sky2_resume.

Factor the code to bring the interfaces down into
sky2_all_down and the up code into sky2_all_up.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Shut off interrupts before NAPI

Interrupts should be masked, then synchronized, and
finally NAPI should be disabled.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Avoid race in sky2_change_mtu

netif_stop_queue does not ensure all in-progress transmits are complete,
 so use netif_tx_disable() instead.

Secondly, make sure NAPI polls are disabled before stopping the tx queue,
 otherwise sky2_status_intr might trigger a TX queue wakeup between when
 we stop the queue and NAPI is disabled.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Restore multicast after restart

Multicast settings will be lost on reset, so restore them.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgb and e1000: Use new function for copybreak tests

There appears to be an off-by-1 defect in the maximum packet size
copied when copybreak is speified in these modules.

The copybreak module params are specified as:
"Maximum size of packet that is copied to a new buffer on receive"

The tests are changed from "< copybreak" to "<= copybreak"
and moved into new static functions for readability.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: cleanup unused parameters

During the cleanup pass after the removal of e1000e hardware from e1000 some
parameters were missed.  Remove them because it is just dead code.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: fix WARN_ON with mac-vlan

When adding more than 14 mac-vlan adapters on e1000 the driver
would fire a WARN_ON when adding the 15th.  The WARN_ON in this
case is completely un-necessary, as the code below the WARN_ON is
directly handling the value the WARN_ON triggered on.

CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: Remove unnecessary returns from void function()s

This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Refactor common code between 82598 & 82599 to accommodate new hardware

Some of the following MAC functions are moved from 82598 & 82599 specific
hardware files to common.[ch] to accommodate new silicon changes. Also
fixed some white space issues
 * get_san_mac_addr, check_link, set_vmdq, clear_vmdq, clear_vfta,
 * set_vfta, fc_enable, init_uta_tables

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Use bool flag to see if the packet unmapping is delayed in HWRSC

We can't use zero magic "bad" value to check if IXGBE_RSC_CB(skb)->dma
is valid. It is only valid in x86/arm/m68k/alpha architectures and in
spark, powerPC and other architectures it should be ~0. As per
Benjamin Herrenschmidt feedback use a bool flag to decide if
the packet unmapping is delayed in hardware RSC till EOP is reached

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: fix setting of promisc mode when using mac-vlans

Introduce uc_set_promisc flag to fix enabling of promisc mode
when exceeding the number of supported RAR entries.

Issue discovered by Ben Greear when using mac-vlans.

Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-next-2.6

netfilter: remove unnecessary returns from void function()s

This patch removes from net/ netfilter files
all the unnecessary return; statements that precede the
last closing brace of void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

Signed-off-by: Joe Perches <joe@perches.com>
[Patrick: changed to keep return statements in otherwise empty function bodies]
Signed-off-by: Patrick McHardy <kaber@trash.net>

netfilter: cleanup printk messages

Make sure all printk messages have a severity level.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

netfilter: change NF_ASSERT to WARN_ON

Change netfilter asserts to standard WARN_ON. This has the
benefit of backtrace info and also causes netfilter errors
to show up on kerneloops.org.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

netfilter: bridge-netfilter: fix crash in br_nf_forward_finish()

[ 4593.956206] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
[ 4593.956219] IP: [<ffffffffa03357a4>] br_nf_forward_finish+0x154/0x170 [bridge]
[ 4593.956232] PGD 195ece067 PUD 1ba005067 PMD 0
[ 4593.956241] Oops: 0000 [#1] SMP
[ 4593.956248] last sysfs file:
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:08/ATK0110:00/hwmon/hwmon0/temp2_label
[ 4593.956253] CPU 3
...
[ 4593.956380] Pid: 29512, comm: kvm Not tainted 2.6.34-rc7-net #195 P6T DELUXE/System Product Name
[ 4593.956384] RIP: 0010:[<ffffffffa03357a4>]  [<ffffffffa03357a4>] br_nf_forward_finish+0x154/0x170 [bridge]
[ 4593.956395] RSP: 0018:ffff880001e63b78  EFLAGS: 00010246
[ 4593.956399] RAX: 0000000000000608 RBX: ffff880057181700 RCX: ffff8801b813d000
[ 4593.956402] RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff880057181700
[ 4593.956406] RBP: ffff880001e63ba8 R08: ffff8801b9d97000 R09: ffffffffa0335650
[ 4593.956410] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801b813d000
[ 4593.956413] R13: ffffffff81ab3940 R14: ffff880057181700 R15: 0000000000000002
[ 4593.956418] FS:  00007fc40d380710(0000) GS:ffff880001e60000(0000) knlGS:0000000000000000
[ 4593.956422] CS:  0010 DS: 002b ES: 002b CR0: 000000008005003b
[ 4593.956426] CR2: 0000000000000018 CR3: 00000001ba1d7000 CR4: 00000000000026e0
[ 4593.956429] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 4593.956433] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 4593.956437] Process kvm (pid: 29512, threadinfo ffff8801ba566000, task ffff8801b8003870)
[ 4593.956441] Stack:
[ 4593.956443]  0000000100000020 ffff880001e63ba0 ffff880001e63ba0 ffff880057181700
[ 4593.956451] <0> ffffffffa0335650 ffffffff81ab3940 ffff880001e63bd8 ffffffffa03350e6
[ 4593.956462] <0> ffff880001e63c40 000000000000024d ffff880057181700 0000000080000000
[ 4593.956474] Call Trace:
[ 4593.956478]  <IRQ>
[ 4593.956488]  [<ffffffffa0335650>] ? br_nf_forward_finish+0x0/0x170 [bridge]
[ 4593.956496]  [<ffffffffa03350e6>] NF_HOOK_THRESH+0x56/0x60 [bridge]
[ 4593.956504]  [<ffffffffa0335282>] br_nf_forward_arp+0x112/0x120 [bridge]
[ 4593.956511]  [<ffffffff813f7184>] nf_iterate+0x64/0xa0
[ 4593.956519]  [<ffffffffa032f920>] ? br_forward_finish+0x0/0x60 [bridge]
[ 4593.956524]  [<ffffffff813f722c>] nf_hook_slow+0x6c/0x100
[ 4593.956531]  [<ffffffffa032f920>] ? br_forward_finish+0x0/0x60 [bridge]
[ 4593.956538]  [<ffffffffa032f800>] ? __br_forward+0x0/0xc0 [bridge]
[ 4593.956545]  [<ffffffffa032f86d>] __br_forward+0x6d/0xc0 [bridge]
[ 4593.956550]  [<ffffffff813c5d8e>] ? skb_clone+0x3e/0x70
[ 4593.956557]  [<ffffffffa032f462>] deliver_clone+0x32/0x60 [bridge]
[ 4593.956564]  [<ffffffffa032f6b6>] br_flood+0xa6/0xe0 [bridge]
[ 4593.956571]  [<ffffffffa032f800>] ? __br_forward+0x0/0xc0 [bridge]

Don't call nf_bridge_update_protocol() for ARP traffic as skb->nf_bridge isn't
used in the ARP case.

Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>

cxgb4: report GRO stats with ethtool -S

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: report the PCIe link speed

Report the PCIe link speed (2.5 or 5 Gbps).

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: configure HW VLAN extraction through FW

HW VLAN extraction needs to be configured through FW to work correctly in
virtualization environments.  Remove the direct register manipulation and
rely on FW.

Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: add PCI device id to enable support for 82567V-4

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Fix/cleanup PHY reset code for ICHx/PCHx

i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling
e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to
make sure the MAC had completed the PHY configuration.  However,
e1000_lan_init_done_ich8lan() had already been called in one of the two
places where PHY reset occurs for ICHx/PCHx parts, which caused the second
call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already
been checked and cleared.

ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset
in e1000_reset_hw_ich8lan() and the PHY-only reset in
e1000_phy_hw_reset_ich8lan().  There was duplicate code in both paths to be
performed post-reset that are now combined into one new function -
e1000_post_phy_reset_ich8lan().  This cleanup also included moving the
clearing of the PHY Reset Asserted bit in the STATUS register (now done for
all ICH/PCH parts) and the check for the indication from h/w that basic
configuration has completed back to where it previously was in
e1000_get_cfg_done_ich8lan().

iii) Corrected a few comments

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: move settting of flow control refresh timer to link setup code

The flow control refresh timer value needs to be saved off so that it can
be programmed into the approrpiate register when applicable but without a
reset, e.g. when changing flow control parameters via ethtool.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: fix checks for manageability enabled and management pass-through

The mac->arc_subsystem was being incorrectly used to flag whether or not
manageability was enabled when it should only be used to state whether the
ARC (Host interface) subsystem is available on a particular MAC _and_ only
valid when any manageability is enabled. The ARC subsystem is currently
only available on 80003es2lan and 82573 parts supported by the driver.

A new flag, has_fwsm, is introduced to be used when checking if
manageability is enabled but only on parts that acutally have an FWSM
register. While the above parts have an FWSM register, there are other
parts that have FWSM but do not have support for the ARC subsystem,
namely 82571/2 and ICHx/PCH.

And then there are parts that have manageability, but do not have either
FWSM register or support for the ARC subsystem - these are 82574 and 82583.

For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no
functional changes, it only corrects the usage of the manageability flags.
For 82574 and 82583, it fixes the incorrect accesses of the non-existent
FWSM register and ARC subsystem as well as corrects the check for
management pass-through.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Incorrect function pointer set for force_speed_duplex on 82577

The force_speed_duplex function pointer was incorrectly set.  Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Cleanup e1000_sw_lcd_config_ich8lan()

After every reset all ICH/PCH parts call this function which acquires the
swflag, performs a workaround on applicable parts and releases the swflag.
There is no reason for parts for which this workaround is not applicable
to acquire and release the swflag so the function should just return
without doing anything for these parts.  This also provides for the
indentation of most of the function contents to be shifted left cleaning up
the code.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: Remove EN_MAC_ADDR_FILTER check from enable_mng_pass_thru check

Patch addresses issues when manageability passthrough is enabled, but the
MAC_ADDR_FILTER bit is not set in the MANC register.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: cleanup multiple common exit points

...in e1000_update_nvm_checksum_ich8lan().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: s/w initiated LSC MSI-X interrupts not generated; no transmit

In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set.  Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: initialize manageability (IPMI) pass-through in 82574/82583

82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through.  Rename the function to better reflect what it does.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: bad state after running ethtool diagnostics with AMT enabled

When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc.  Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: use static params to save stack space (part 2)

A couple stack cleanups missed in an earlier patch from Jesse.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/kaber/ipmr-2.6

netxen: handle queue manager access

Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.

Support for only NX3031 based cards.

Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: to fix onchip memory access.

Remove unnecessary remap of the region in bar 0 to access onhip memory
for NX3031.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: remove unnecessary size checks

NX3031 have 64bit on card memory. Fix the limit check to
64MB and remove unnecessary 128bit read/write check.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: fix register usage

o For NX3031, MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers
  are obsolete. These register addresses can be used for different
  purpose.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining tipc_msg_* routines

Convert tipc_msg_* inline routines that are more than one line into
standard functions, thereby eliminating some repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining buf_acquire routine

Convert buf_acquire inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining bearer congestion routine

Convert bearer congestion inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining port list routines

Converts port list inline routines that are more than one line into
standard functions, thereby eliminating a significant amount of
repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining nmap routines

Converts nmap inline routines that are more than one line into standard
functions, thereby eliminating a significant amount of repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Reduce footprint by un-inlining address routines

Convert address-related inline routines that are more than one
line into standard functions, thereby eliminating a significant
amount of repeated code.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: add tipc_ prefix to fcns targeted for un-inlining

These functions have enough code in them such that they
seem like sensible targets for un-inlining.  Prior to doing
that, this adds the tipc_ prefix to the functions, so that
in the event of a panic dump or similar, the subsystem from
which the functions come from is immediately clear.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Relocate trivial link status functions to header file

Rather than live in link.c where they can only be used in that file alone,
these helper routines are better served by being in link.h

Relocated are the following:

link_working_working
link_working_unknown
link_reset_unknown
link_reset_reset
link_blocked
link_congested

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: remove abstraction for link_max_pkt

This is just a straight return of a field; there is no
value in the abstraction of hiding it behind a function.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Update commenting in TIPC API

Eliminate comments in TIPC's main API files that are either obsolete,
incorrect, misleading, or unhelpful.  It also adds in one new comment.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Add support for "-s" configuration option

Provide initial support for displaying overall TIPC status/statistics
information at runtime.  Currently, only version info for the TIPC
kernel module is displayed.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Rename "multicast-link" to "broadcast-link"

Make a cosmetic change to the name displayed for the broadcast link,
to better reflect its true nature. Since TIPC utilizes this link to
distribute name table information, in addition to multicast messages
sent by user applications, the prior name "multicast-link" is
no longer appropriate.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Eliminate unnecessary initialization in native API send routines

Eliminate a couple of instances where TIPC's native API send routines
were doing pointless initialization of local variables.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Prune unused data structures from configuration service

Eliminate some unused data structures in the TIPC
configuration service that relate to the handling of link
subscriptions, which were not supported when TIPC 1.5 was
introduced.  If and when support for link subscriptions is
offered in TIPC, these elements may need to be re-introduced.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Eliminate unused argument in print statement

Eliminate an argument in a print statement that has no corresponding
format specification.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: Eliminate obsolete port's "congested_link" field

Eliminate a field of the TIPC port structure that is populated,
but never referenced.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: xtables: add missing depends for xt_TEE

Aviod these link-time errors when IPV6=m, XT_TEE=y:

net/built-in.o: In function `tee_tg_route6':
xt_TEE.c:(.text+0x45ca5): undefined reference to `ip6_route_output'
net/built-in.o: In function `tee_tg6':
xt_TEE.c:(.text+0x45d79): undefined reference to `ip6_local_out'

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wireless/ath/ar9170/usb.c
drivers/scsi/iscsi_tcp.c
net/ipv4/ipmr.c

Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (applesmc) Correct sysfs fan error handling
  hwmon: (asc7621) Bug fixes

Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  kprobes/x86: Fix removed int3 checking order
  perf: Fix static strings treated like dynamic ones

drivers/gpu/drm/i915/i915_irq.c:i915_error_object_create(): use correct kmap-atomic slot

i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot.  Use KM_IRQ0 instead.

Reported-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hp_accel: fix race in device removal

The work queue has to be flushed after the device has been made
inaccessible.  The patch closes a window during which a work queue might
remain active after the device is removed and would then lead to ACPI
calls with undefined behavior.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Herrmann <morpheus.ibis@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mqueue: fix kernel BUG caused by double free() on mq_open()

In case of aborting because we reach the maximum amount of memory which
can be allocated to message queues per user (RLIMIT_MSGQUEUE), we would
try to free the message area twice when bailing out: first by the error
handling code itself, and then later when cleaning up the inode through
delete_inode().

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: bfin-t350mcqb-fb: fix fbmem allocation with blanking lines

The current allocation does not include the memory required for blanking
lines.  So avoid memory corruption when multiple devices are using the DMA
memory near each other.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix css_is_ancestor() RCU locking

Some callers (in memcontrol.c) calls css_is_ancestor() without
rcu_read_lock.  Because css_is_ancestor() has to access RCU protected
data, it should be under rcu_read_lock().

This makes css_is_ancestor() itself does safe access to RCU protected
area.  (At least, "root" can have refcnt==0 if it's not an ancestor of
"child".  So, we need rcu_read_lock().)

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix css_id() RCU locking for real

Commit ad4ba375373937817404fd92239ef4cadbded23b ("memcg: css_id() must be
called under rcu_read_lock()") modifies memcontol.c for fixing RCU check
message.  But Andrew Morton pointed out that the fix doesn't seems sane
and it was just for hidining lockdep messages.

This is a patch for do proper things.  Checking again, all places,
accessing without rcu_read_lock, that commit fixies was intentional....
all callers of css_id() has reference count on it.  So, it's not necessary
to be under rcu_read_lock().

Considering again, we can use rcu_dereference_check for css_id().  We know
css->id is valid if css->refcnt > 0.  (css->id never changes and freed
after css->refcnt going to be 0.)

This patch makes use of rcu_dereference_check() in css_id/depth and remove
unnecessary rcu-read-lock added by the commit.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bsdacct: use del_timer_sync() in acct_exit_ns()

acct_exit_ns --> acct_file_reopen deletes timer without check timer
execution on other CPUs.  So acct_timeout() can change an unmapped memory.

Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rmap: remove anon_vma check in page_address_in_vma()

Currently page_address_in_vma() compares vma->anon_vma and
page_anon_vma(page) for parameter check, but in 2.6.34 a vma can have
multiple anon_vmas with anon_vma_chain, so current check does not work.
(For anonymous page shared by multiple processes, some verified (page,vma)
pairs return -EFAULT wrongly.)

We can go to checking all anon_vmas in the "same_vma" chain, but it needs
to meet lock requirement.  Instead, we can remove anon_vma check safely
because page_address_in_vma() assumes that page and vma are already
checked to belong to the identical process.

Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlbfs: kill applications that use MAP_NORESERVE with SIGBUS instead of OOM-killer

Ordinarily, application using hugetlbfs will create mappings with
reserves.  For shared mappings, these pages are reserved before mmap()
returns success and for private mappings, the caller process is guaranteed
and a child process that cannot get the pages gets killed with sigbus.

An application that uses MAP_NORESERVE gets no reservations and mmap()
will always succeed at the risk the page will not be available at fault
time.  This might be used for example on very large sparse mappings where
the developer is confident the necessary huge pages exist to satisfy all
faults even though the whole mapping cannot be backed by huge pages.
Unfortunately, if an allocation does fail, VM_FAULT_OOM is returned to the
fault handler which proceeds to trigger the OOM-killer.  This is
unhelpful.

Even without hugetlbfs mounted, a user using mmap() can trivially trigger
the OOM-killer because VM_FAULT_OOM is returned (will provide example
program if desired - it's a whopping 24 lines long).  It could be
considered a DOS available to an unprivileged user.

This patch alters hugetlbfs to kill a process that uses MAP_NORESERVE
where huge pages were not available with SIGBUS instead of triggering the
OOM killer.

This change affects hugetlb_cow() as well.  I feel there is a failure case
in there, but I didn't create one.  It would need a fairly specific target
in terms of the faulting application and the hugepage pool size.  The
hugetlb_no_page() path is much easier to hit but both might as well be
closed.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kexec: fix OOPS in crash_kernel_shrink

Two "echo 0 > /sys/kernel/kexec_crash_size" OOPSes kernel.  Also content
of this file is invalid after first shrink to zero: it shows 1 instead of
0.

This scenario is unlikely to happen often (root privs, valid crashkernel=
in cmdline, dump-capture kernel not loaded), I hit it only by chance.

This patch fixes it.

Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: fix in debugfs: response value printing

In debugfs, printing of command response reports resp[2] twice: fix it to
resp[3].

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: remove data error interrupt after xfer

Disable data error interrupts while we are actually recording that there
is not such errors.  This will prevent, in some cases, the warning message
printed at new request queuing (in atmci_start_request()).

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: prevent kernel oops while removing card

The removing of an SD card in certain circumstances can lead to a kernel
oops if we do not make sure that the "data" field of the host structure is
valid.  This patch adds a test in atmci_dma_cleanup() function and also
calls atmci_stop_dma() before throwing away the reference to data.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmc: atmel-mci: fix two parameters swapped

Two parameters were swapped in the calls to atmci_init_slot().

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Anders Grahn <anders.grahn@hd-wireless.se>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

revert "procfs: provide stack information for threads" and its fixup commits

Originally, commit d899bf7b ("procfs: provide stack information for
threads") attempted to introduce a new feature for showing where the
threadstack was located and how many pages are being utilized by the
stack.

Commit c44972f1 ("procfs: disable per-task stack usage on NOMMU") was
applied to fix the NO_MMU case.

Commit 89240ba0 ("x86, fs: Fix x86 procfs stack information for threads on
64-bit") was applied to fix a bug in ia32 executables being loaded.

Commit 9ebd4eba7 ("procfs: fix /proc/<pid>/stat stack pointer for kernel
threads") was applied to fix a bug which had kernel threads printing a
userland stack address.

Commit 1306d603f ('proc: partially revert "procfs: provide stack
information for threads"') was then applied to revert the stack pages
being used to solve a significant performance regression.

This patch nearly undoes the effect of all these patches.

The reason for reverting these is it provides an unusable value in
field 28.  For x86_64, a fork will result in the task->stack_start
value being updated to the current user top of stack and not the stack
start address.  This unpredictability of the stack_start value makes
it worthless.  That includes the intended use of showing how much stack
space a thread has.

Other architectures will get different values.  As an example, ia64
gets 0.  The do_fork() and copy_process() functions appear to treat the
stack_start and stack_size parameters as architecture specific.

I only partially reverted c44972f1 ("procfs: disable per-task stack usage
on NOMMU") .  If I had completely reverted it, I would have had to change
mm/Makefile only build pagewalk.o when CONFIG_PROC_PAGE_MONITOR is
configured.  Since I could not test the builds without significant effort,
I decided to not change mm/Makefile.

I only partially reverted 89240ba0 ("x86, fs: Fix x86 procfs stack
information for threads on 64-bit") .  I left the KSTK_ESP() change in
place as that seemed worthwhile.

Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>