[media] cxd2841er: don't use variable length arrays

The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:

drivers/media/dvb-frontends/cxd2841er.c:205:19: warning: Variable length array is used.

The max usecase of the driver seems to be 15 bytes + 1 for the
register.

So, let's be safe and allocate 17 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driver

Add NetUP Dual Universal CI PCIe board driver.
The board has
    - two CI slots
    - two I2C adapters
    - SPI master bus for accessing flash memory containing
      FPGA firmware

No changes required.

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] cxd2841er: declare static functions as such

drivers/media/dvb-frontends/cxd2841er.c:992:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_t2' [-Wmissing-prototypes]
 int cxd2841er_get_carrier_offset_t2(
     ^
drivers/media/dvb-frontends/cxd2841er.c:1032:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_c' [-Wmissing-prototypes]
 int cxd2841er_get_carrier_offset_c(
     ^
drivers/media/dvb-frontends/cxd2841er.c:1360:5: warning: no previous prototype for 'cxd2841er_read_snr_t2' [-Wmissing-prototypes]
 int cxd2841er_read_snr_t2(struct cxd2841er_priv *priv, u32 *snr)
     ^

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] cxd2841er: Sony CXD2841ER DVB-S/S2/T/T2/C demodulator driver

Add DVB-C/T/T2/S/S2 demodulator frontend driver Sony CXD2841ER chip.

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] lnbh25: LNBH25 SEC controller driver

Add DVB SEC frontend driver for STM LNBH25PQR chip.

[mchehab@osg.samsung.com: fix merge conflict:
 fe_sec_voltage_t should not be used in kernelspace anymore.
 instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] ascot2e: Sony Ascot2e DVB-C/T/T2 tuner driver

Add DVB-T/T2/C frontend driver for Sony Ascot2e (CXD2861ER) chip.

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver

Add DVB-S/S2 frontend driver for Sony Horus3A (CXD2832AER) chip

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] Technisat SkyStar USB HD,(DVB-S/S2) too much URBs for arm devices

Using 8 URBs results in a consecutive buffer allocation of too much
memory for some arm devices.
As we use isochronuous transfers the number of URBs can be reduced
without risking data-loss.

Signed-off-by: Christian Loepke <loepke@edfritsch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] rc-core: improve the lirc protocol reporting

Commit 275ddb40bcf686d210d86c6718e42425a6a0bc76 removed the lirc
"protocol" but kept backwards compatibility by always listing
the protocol as present and enabled. This patch further improves
the logic by only listing the protocol if the lirc module is loaded
(or if lirc is builtin).

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] staging: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] staging: iio: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] staging: media: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tuners: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] radio: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] i2c: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] dvb-frontends: Drop owner assignment from platform_driver

platform_driver does not need to set an owner because
platform_driver_register() will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] dvb-frontends: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] pctv452e: Replace memset with eth_zero_addr

Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Note that the 6 in the third argument of memset appears to represent
an ethernet address size (ETH_ALEN).

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@eth_zero_addr@
expression e;
@@

-memset(e,0x00,6);
+eth_zero_addr(e);
// </smpl>

Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tuners: Make all TV tuners visible if COMPILE_TEST=y

Make the TV tuners menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.

Without this, many drivers stay disabled during e.g. allmodconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] ttpci: Replace memset with eth_zero_addr

Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Note that the 6 in the third argument of memset appears to represent
an ethernet address size (ETH_ALEN).

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@eth_zero_addr@
expression e;
@@

-memset(e,0x00,6);
+eth_zero_addr(e);
// </smpl>

Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usb/airspy: removing unneeded goto

This patch removes unneded goto,
reported by coccinelle.

Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Akhilesh Kumar <akhilesh.k@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] i2c: Make all i2c devices visible if COMPILE_TEST=y

Make the i2c devices menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.

Without this, many drivers stay disabled during e.g. allmodconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] dvb-frontends: Make all DVB Frontends visible if COMPILE_TEST=y

Make the DVB Frontends menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.

Without this, many drivers stay disabled during e.g. allmodconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] x86/mm/pat, drivers/media/ivtv: move pat warn and replace WARN() with pr_warn()

On built-in kernels this warning will always splat as this is part
of the module init. Fix that by shifting the PAT requirement check
out under the code that does the "quasi-probe" for the device. This
device driver relies on an existing driver to find its own devices,
it looks for that device driver and its own found devices, then
uses driver_for_each_device() to try to see if it can probe each of
those devices as a frambuffer device with ivtvfb_init_card(). We
tuck the PAT requiremenet check then on the ivtvfb_init_card()
call making the check at least require an ivtv device present
before complaining.

Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5c73m3: Remove redundant spi driver bus initialization

In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] pci/Kconfig: don't use MEDIA_ANALOG_TV_SUPPORT for grabber cards

I noticed certain cards are currently under MEDIA_ANALOG_TV_SUPPORT
but it seems they are frame grabbers (with CVBS, Svideo etc. inputs)
rather than TV receivers (with analog TV tuners).

MEDIA_CAMERA_SUPPORT maybe isn't the best name (only "meye" driver seems
to drive a real camera in a laptop) but it at least doesn't select the
TUNERs.

Perhaps the following patch would make sense.

Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] mantis: remove an uneeded goto

Gotos makes a little harder to check the code. In this
particular case, the goto is doing nothing but jumping into
a return.

Instead, just replace the goto by the return, making it
simpler.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] mantis: Fix error handling in mantis_dma_init()

Current code assigns 0 to variable 'err', which makes mantis_dma_init()
to return success even if mantis_alloc_buffers() fails.

Fix it by checking the return value from mantis_alloc_buffers() and
propagating it in the case of error.

Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] mt9v032: fix uninitialized variable warning

drivers/media/i2c/mt9v032.c: In function ‘mt9v032_probe’:
  CC [M]  drivers/media/i2c/s5k4ecgx.o
drivers/media/i2c/mt9v032.c:996:20: warning: ‘pdata’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  if (pdata && pdata->link_freqs) {
                    ^

It can indeed be uninitialized in one corner case. Initialize to NULL.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] v4l2: move tracepoint generation into separate file

To compile videobuf2-core as a module, the vb2_* tracepoints must be
exported from the videodev module. Instead of exporting vb2 tracepoint
symbols from v4l2-ioctl.c, move the tracepoint generation into a separate
file. This patch fixes the following build error in the modpost stage,
introduced by 2091f5181c66 ("[media] videobuf2: add trace events"):

    ERROR: "__tracepoint_vb2_buf_done" undefined!
    ERROR: "__tracepoint_vb2_dqbuf" undefined!
    ERROR: "__tracepoint_vb2_qbuf" undefined!
    ERROR: "__tracepoint_vb2_buf_queue" undefined!

Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] vivid: support cvt, gtf timings for video out

The generation of cvt, gtf timings is already supported by v4l2-ctl.
This patch adds support for setting cvt,gtf timings for video out.
While enabling cvt,gtf in vivid capture, the vivid video out was
missed out. Adding it now.

Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: adv7604: reduce support to first (digital) input

Using adv7611_read_cable_det() for ADV7612 means that full
support for '.max_port = ADV7604_PAD_HDMI_PORT_B,' isn't available
due to the need for multiple port reads to determine cable detection,
and an agreed mechanism for communicating the separate statuses.

This patch replaces adv7611_read_cable_det() with a functionally
identical copy, commented appropriately.

Earlier submissions [leading to commit 8331d30b] also set .cp_csc,
which is used in a cp_read() call within adv76xx_log_status().

Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: adv7604: fix probe of ADV7611/7612

Prior to commit f862f57d ("[media] media: i2c: ADV7604: Migrate to
regmap"), the local variable 'val' contained the combined register
reads used in the chipset version ID test. Restore this expectation
so that the comparison works as it used to.

Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] soc_camera: always release queue for queue owner

Always release the queue if the owner closes its filehandle and not when
it is the last open filehandle.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] soc_camera: pass on streamoff error

If streamoff returned an error, then pass that on to the caller.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] soc_camera: compliance fixes

- REQBUFS(0) will stop streaming, free buffers and release the file ownership.
- Return ENOTTY for create_bufs for a vb1 driver
- Return EBUSY if there is a different streaming owner and set the new owner on
  success.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] soc_camera: fix expbuf support

- For vb1 drivers just return -ENOTTY.
- For vb2 drivers allow vb2_expbuf without there being a stream owner:
  the vb2_expbuf function will return the correct error message in that case.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] soc_camera: fix enum_input

Fill in the std field from the video_device tvnorms field.

This fixes a v4l2-compliance failure.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] sh_mobile_ceu_camera: set field to FIELD_NONE

Make sure that 'field' isn't FIELD_ANY when the driver is
first loaded. Fixes a v4l2-compliance failure.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] sh_mobile_ceu_camera: fix querycap

Fill in the bus_info and driver fields. Found by v4l2-compliance.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] mt9t112: JPEG -> SRGB

The JPEG colorspace should only be used for JPEG encoded images. This is
just a regular sRGB sensor.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] ak881x: simplify standard checks

Simplify confusing conditions. This also swaps the checks for NTSC and PAL:
to be consistent with other drivers check for NTSC first. So if the user
sets both NTSC and PAL bits, then NTSC wins.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tw9910: init priv->scale and update standard

When the standard changes the VACTIVE and VDELAY values need to be updated.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tw9910: don't use COLORSPACE_JPEG

This is an SDTV video receiver, so the colorspace should be SMPTE170M.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] sh-veu: initialize timestamp_flags and copy timestamp info

This field wasn't set, causing WARN_ON's from the vb2 core.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tda10071: implement DVBv5 statistics

Implement DVBv5 CNR, signal strength, BER and block errors.

Wrap legacy DVBv3 statistics to DVBv5 internally.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tda10071: do not get_frontend() when not ready

This is a bit hack, but returning error when driver is not tuned yet
causes DVBv5 zap stop polling DVBv5 statistics. Thus return 0 even
callback is called during invalid device state.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tda10071: protect firmware command exec with mutex

There should be clearly some lock in order to make sure firmware
command in execution is not disturbed by another command. It has
worked as callbacks are serialized somehow pretty well and command
execution happens usually without any delays.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tda10071: convert to regmap I2C API

Use regmap API for I2C operations.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tda10071: rename device state struct to dev

Rename device state struct from 'priv' to 'dev'.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tda10071: remove legacy media attach

All users are now using I2C binding and old attach could be removed.
Use I2C client for proper logging at the same.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] a8293: coding style issues

Remove FSF address from license. Indent parameter correctly.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] a8293: improve LNB register programming logic

On power-on LNB power supply voltage is disabled, due to that no
need to disable it during probe. Tone is supply is hard-coded as
external tone coming from the demodulator. Program both voltage
and tone on set_voltage(). Use register cache to prevent unneeded
programming.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] a8293: use i2c_master_send / i2c_master_recv for I2C I/O

As driver is now proper I2C client driver, we could use correct
functions for I2C I/O. Also rename state from priv to dev. Fix
logging too.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] a8293: remove legacy media attach

Remove legacy media attach as all users are on I2C bindings now.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] em28xx: remove unused a8293 SEC config

Devices that were using a8293 SEC are converted to I2C platform data
thus that old config structure is left unused.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] bt819/saa7110/vpx3220: remove legacy control ops

The zoran driver has now been converted to the control framework
which means that these three subdevice drivers no longer need to
support the legacy core control ops since the last bridge driver
that needed that has now been converted.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] zoran: convert to the control framework and to v4l2_fh

Switch this driver to the control framework and to v4l2_fh for
handling control events.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] zoran: use standard core lock

Use the standard core lock to take care of serializing ioctl calls and
to serialize file operations.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] zoran: remove unused read/write functions

The zoran_read/write functions always return an error. Just remove them.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] zoran: remove unnecessary memset

There is no need to zero the v4l2_capability struct, the v4l2 core has done
that already.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] fsl-viu: drop format names

The names of the pixelformats is set by the core. So there no longer
is any need for drivers to fill it in.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] fsl-viu: small fixes

- Fix an off-by-one index check in vidioc_enum_fmt()
- Fill in the pix.sizeimage field in vidioc_try_fmt_cap()
- Fix an off-by-one index check in vidioc_s_input()

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] fsl-viu: add control event support

Convert the driver to use v4l2_fh in order to support control events.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] fsl-viu: fill in colorspace, always set field to interlaced

- fill in the missing colorspace value.
- don't reject incorrect field values, always replace with a valid value.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] fsl-viu: fill in bus_info in vidioc_querycap

The bus_info field was never filled.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] fsl-viu: convert to the control framework

Interestingly enough, the existing control handling code basically did
nothing. At least the new code will inherit the controls from the
saa7115 driver.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: move init code to probe()

These things are only initialized if you start streaming video, but
they are also used in the disconnect function. So just init them
always during probe time.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: fix standards for S-Video/Composite inputs

The standards supported by S-Video and Composite inputs are not
limited by PAL, so make it more generic.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: fix DMA from stack warnings

In various places the stack was used to provide buffers for USB data, but
this should be allocated memory.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: fix locking error

If remove_pending is non-zero, then the v4l2_lock is never unlocked.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: set field and colorspace

Set the colorspace and field in vidioc_try_fmt_vid_cap().

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: frequency fixes

- setup initial radio and tv frequencies.
- set/get the correct frequency (radio vs tv).
- disable tuner/freq ioctls if there is no tuner.
- fix some tuner index checks.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: the radio device node has wrong caps

The radio device node had the same caps as the video node. Fix this.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: remove g/s_audio and for radio remove enum/g/s_input

The g/s_audio ioctls didn't do anything, so remove them all for both
video and radio nodes and remove V4L2_CAP_AUDIO.

The enum/g/s_input ioctls are invalid for radio nodes, so remove them
from the radio ioctl_ops.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: return valid error in usbvision_register_video()

Don't return -1, return a proper error code.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: convert to the control framework

Convert this driver to the control framework and struct v4l2_fh
(needed for handling control events).

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] usbvision: remove power_on_at_open and timed power off

This causes lots of problems and is *very* slow as well.

One of the main problems is that this prohibits the use of the control
framework since subdevs will be unloaded on power off which is not allowed
as long as they are used by a usb device.

Apparently the reason for doing this is to turn off a noisy tuner. My hardware
has no problem with that, and I wonder whether the hardware with that noisy
tuner wasn't just functioning improperly as I have never heard of noisy tuners.

Contact me if you have one of those devices and I can take a look whether the
tuner can't be powered off if necessary by letting the tuner subdevice go
into standby mode. Unloading the tuner module is just evil and is not the
right approach.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] DocBook: Fix typo in intro.xml

This patch fix spelling typos in intro.xml.
This xml file is not created from comments within source,
I fix the xml file.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
[hans.verkuil@cisco.com: removed mention of obsolete devfs]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] MAINTAINERS: V4L2: PLATFORM: Add entry for Renesas JPEG Processing Unit driver

Update RENESAS JPU driver maintainer in MAINTAINERS file.

Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] V4L2: platform: Add Renesas R-Car JPEG codec driver

Here's the driver for the Renesas R-Car JPEG processing unit.

The driver is implemented within the V4L2 framework as a memory-to-memory
device.  It presents two video nodes to userspace, one for the encoding part,
and one for the decoding part.

It was found that the only working mode for encoding is no markers output, so we
generate markers with software. In the current version of driver we also use
software JPEG header parsing because with hardware parsing performance is lower
than desired.

>From a userspace point of view the process is typical (S_FMT, REQBUF,
optionally QUERYBUF, QBUF, STREAMON, DQBUF) for both the source and destination
queues. STREAMON can return -EINVAL in case of mismatch of output and capture
queues format. Also during decoding driver can return buffers if queued
buffer with JPEG image contains image with inappropriate subsampling (e.g.
4:2:0 in JPEG and 4:2:2 in capture).  If JPEG image and queue format dimensions
differ driver will return buffer on QBUF with VB2_BUF_STATE_ERROR flag.

During encoding the available formats are: V4L2_PIX_FMT_NV12M,
V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16, V4L2_PIX_FMT_NV16M for source and
V4L2_PIX_FMT_JPEG for destination.

During decoding the available formats are: V4L2_PIX_FMT_JPEG for source and
V4L2_PIX_FMT_NV12M, V4L2_PIX_FMT_NV16M, V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16
for destination.

Performance of current version:
1280x800 NV12 image encoding/decoding
decoding ~122 FPS
encoding ~191 FPS

Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] devicetree: bindings: Document Renesas R-Car JPEG Processing Unit

Add Renesas R-Car JPEG processing unit driver device tree bindings
documentation.

Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] v4l2-ioctl: Give more information when device_caps are missing

Currently, the warning for missing device_caps gives a backtrace like so:

[<ffffffff8175c199>] dump_stack+0x45/0x57
[<ffffffff8109ad5a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff8109ae8a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0237453>] v4l_querycap+0x43/0x80 [videodev]
[<ffffffffa0237734>] __video_do_ioctl+0x2a4/0x320 [videodev]
[<ffffffff812207e5>] ? do_last+0x195/0x1210
[<ffffffffa023a11e>] video_usercopy+0x22e/0x5b0 [videodev]
[<ffffffffa0237490>] ? v4l_querycap+0x80/0x80 [videodev]
[<ffffffffa023a4b5>] video_ioctl2+0x15/0x20 [videodev]
[<ffffffffa0233733>] v4l2_ioctl+0x113/0x150 [videodev]
[<ffffffff81225798>] do_vfs_ioctl+0x2f8/0x4f0
[<ffffffff8113b2d4>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff81022d7c>] ? do_audit_syscall_entry+0x6c/0x70
[<ffffffff81225a11>] SyS_ioctl+0x81/0xa0
[<ffffffff8113b526>] ? __audit_syscall_exit+0x1f6/0x2a0
[<ffffffff81763549>] system_call_fastpath+0x12/0x17

This indicates that device_caps are missing but doesn't give
much of a clue which driver is actually at fault. Improve
the warning output by showing the capabilities and the
responsible driver.

Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tc358743: remove unused variable

The bt pointer was never used, remove it.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] v4l2-mem2mem: drop lock in v4l2_m2m_fop_mmap

The v4l2_m2m_fop_mmap function takes the core mutex, but this will result in a potential
circular locking dependency:

[  262.517164] ======================================================
[  262.517166] [ INFO: possible circular locking dependency detected ]
[  262.517169] 4.2.0-rc2-koryphon #844 Not tainted
[  262.517171] -------------------------------------------------------
[  262.517173] v4l2-compliance/1379 is trying to acquire lock:
[  262.517175]  (&dev->dev_mutex){+.+.+.}, at: [<ffffffffa000ddab>] v4l2_m2m_fop_mmap+0x2b/0x90 [v4l2_mem2mem]
[  262.517187]
               but task is already holding lock:
[  262.517189]  (&mm->mmap_sem){++++++}, at: [<ffffffff81159309>] vm_mmap_pgoff+0x69/0xc0
[  262.517199]
               which lock already depends on the new lock.

[  262.517202]
               the existing dependency chain (in reverse order) is:
[  262.517204]
               -> #1 (&mm->mmap_sem){++++++}:
[  262.517209]        [<ffffffff810d0e6b>] __lock_acquire+0x62b/0xe80
[  262.517215]        [<ffffffff810d2095>] lock_acquire+0x65/0x90
[  262.517218]        [<ffffffff811612e5>] __might_fault+0x75/0xa0
[  262.517222]        [<ffffffffa06dead9>] video_usercopy+0x3e9/0x4e0 [videodev]
[  262.517231]        [<ffffffffa06debe0>] video_ioctl2+0x10/0x20 [videodev]
[  262.517238]        [<ffffffffa06d8663>] v4l2_ioctl+0xc3/0xe0 [videodev]
[  262.517243]        [<ffffffff811a8cac>] do_vfs_ioctl+0x2fc/0x550
[  262.517248]        [<ffffffff811a8f74>] SyS_ioctl+0x74/0x80
[  262.517252]        [<ffffffff81a4d2ee>] entry_SYSCALL_64_fastpath+0x12/0x76
[  262.517258]
               -> #0 (&dev->dev_mutex){+.+.+.}:
[  262.517262]        [<ffffffff810cf464>] validate_chain.isra.38+0xd04/0x1170
[  262.517266]        [<ffffffff810d0e6b>] __lock_acquire+0x62b/0xe80
[  262.517270]        [<ffffffff810d2095>] lock_acquire+0x65/0x90
[  262.517273]        [<ffffffff81a48e3c>] mutex_lock_interruptible_nested+0x6c/0x4b0
[  262.517279]        [<ffffffffa000ddab>] v4l2_m2m_fop_mmap+0x2b/0x90 [v4l2_mem2mem]
[  262.517284]        [<ffffffffa06d80ff>] v4l2_mmap+0x4f/0x90 [videodev]
[  262.517288]        [<ffffffff8116b06c>] mmap_region+0x38c/0x5b0
[  262.517293]        [<ffffffff8116b585>] do_mmap_pgoff+0x2f5/0x3e0
[  262.517297]        [<ffffffff8115932a>] vm_mmap_pgoff+0x8a/0xc0
[  262.517300]        [<ffffffff81169bab>] SyS_mmap_pgoff+0x1cb/0x270
[  262.517304]        [<ffffffff8100876d>] SyS_mmap+0x1d/0x20
[  262.517309]        [<ffffffff81a4d2ee>] entry_SYSCALL_64_fastpath+0x12/0x76
[  262.517313]
               other info that might help us debug this:

[  262.517315]  Possible unsafe locking scenario:

[  262.517318]        CPU0                    CPU1
[  262.517319]        ----                    ----
[  262.517321]   lock(&mm->mmap_sem);
[  262.517324]                                lock(&dev->dev_mutex);
[  262.517327]                                lock(&mm->mmap_sem);
[  262.517329]   lock(&dev->dev_mutex);
[  262.517332]
                *** DEADLOCK ***

Since vb2_fop_mmap doesn't take the lock, neither should v4l2_m2m_fop_mmap.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5p-jpeg: Eliminate double kfree()

video_unregister_device() calls device_unregister(), which calls
put_device(), which calls kobject_put(), and if this is the last reference
then kobject_release() is called, which calls kobject_cleanup(), which
calls ktype's release method which happens to be device_release() in this
case, which calls dev->release(), which happens to be
v4l2_device_release() in this case, which calls vdev->release(), which
happens to be video_device_release(). But video_device_release() is
called explicitly both in error recovery path of s5p_jpeg_probe() and
in s5p_jpeg_remove(). The pointers in question are not nullified between
the two calls, so this is harmful.

This patch fixes the driver so that video_device_release() is not called
twice for the same object.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5p-mfc: add additional check for incorrect memory configuration

MFC hardware is known to trash random memory if one tries to use a
buffer which has lower DMA addresses than the configured DMA base
address. This patch adds a check for this case and proper error
handling.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kamil Debski <kamil@wypas.org>
[s.nawrocki@samsung.com: fixed typo (addres -> address]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5p-mfc: add return value check in mfc_sys_init_cmd

alloc_dev_context_buffer method might fail, so add proper
return value check.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5p-mfc: fix state check from encoder queue_setup

MFCINST_GOT_INST state is set to encoder context with set_format
only for capture buffer. In queue_setup of encoder called during
reqbufs, it is checked MFCINST_GOT_INST state for both capture
and output buffer. So this patch fixes encoder to check
MFCINST_GOT_INST state only for capture buffer from queue_setup.

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5p-tv: fix wait_event_timeout return handling

event API conformance testing with coccinelle spatches are being
used to locate API usage inconsistencies this triggert with:
./drivers/media/platform/s5p-tv/mixer_reg.c:364
        incorrect check for negative return

Return type of wait_event_timeout is signed long not int and the
return type is >=0 always thus the negative check is unnecessary.
An appropriately named variable of type long is inserted and the
call fixed up aswell as the negative return check dropped.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] s5p-tv: Drop owner assignment from i2c_driver

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] dvb_core: Replace memset with eth_zero_addr

Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@eth_zero_addr@
expression e;
@@

-memset(e,0x00,ETH_ALEN);
+eth_zero_addr(e);
// </smpl>

Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] staging: media: lirc: fix coding style error

Fix code indentation error by replacing tab in place of spaces.

Signed-off-by: Sunil Shahu <shshahu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] sh-veu: don't use COLORSPACE_JPEG

COLORSPACE_JPEG should only be used for JPEGs. Use SMPTE170M instead,
which is how YCbCr images are usually encoded.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] media: ttpci: Use vsprintf %pM extension

Format mac addresses with the normal kernel extension.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tc358743: allow event subscription

This is useful to subscribe to HDMI hotplug events via the
V4L2_CID_DV_RX_POWER_PRESENT control.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tc358743: add direct interrupt handling

When probed from device tree, the i2c client driver can handle the interrupt
on its own.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tc358743: support probe from device tree

Add support for probing the TC358743 subdevice from device tree.
The reference clock must be supplied using the common clock bindings.
MIPI CSI-2 specific properties are parsed from the OF graph endpoint
node and support for a non-continuous MIPI CSI-2 clock is added.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] tc358743: enable v4l2 subdevice devnode

Add V4L2_SUBDEV_FL_HAS_DEVNODE to subdev flags, in order to
enable a subdev device node.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>