powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()

commit affeb0f2d3a9af419ad7ef4ac782e1540b2f7b28 upstream.

The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.

This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.

Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/book3s64: Fix branching to OOL handlers in relocatable kernel

commit 8ed8ab40047a570fdd8043a40c104a57248dd3fd upstream.

Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.

However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.

But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:

  1. In almost all cases, production kernel (relocatable) is used for
     kdump as well, which would mean that crashed kernel's OOL handler
     would be at the same place where we end up branching to, from short
     interrupt vector of kdump kernel.
  2. Also, OOL handler was unlikely the reason for crash in almost all
     the kdump scenarios, which meant we had a sane OOL handler from
     crashed kernel that we branched to.
  3. On most 64-bit POWER server processors, page size is large enough
     that marking interrupt vector code as executable (see commit
     429d2e83) leads to marking OOL handler code from crashed kernel,
     that sits right below interrupt vector code from kdump kernel, as
     executable as well.

Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.

This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.

Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.

Fixes: c1fb6816fb1b ("powerpc: Add relocation on exception vector handlers")
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pipe: limit the per-user amount of pages allocated in pipes

commit 759c01142a5d0f364a462346168a56de28a80f52 upstream.

On no-so-small systems, it is possible for a single process to cause an
OOM condition by filling large pipes with data that are never read. A
typical process filling 4000 pipes with 1 MB of data will use 4 GB of
memory. On small systems it may be tricky to set the pipe max size to
prevent this from happening.

This patch makes it possible to enforce a per-user soft limit above
which new pipes will be limited to a single page, effectively limiting
them to 4 kB each, as well as a hard limit above which no new pipes may
be created for this user. This has the effect of protecting the system
against memory abuse without hurting other users, and still allowing
pipes to work correctly though with less data at once.

The limit are controlled by two new sysctls : pipe-user-pages-soft, and
pipe-user-pages-hard. Both may be disabled by setting them to zero. The
default soft limit allows the default number of FDs per process (1024)
to create pipes of the default size (64kB), thus reaching a limit of 64MB
before starting to create only smaller pipes. With 256 processes limited
to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB =
1084 MB of memory allocated for a user. The hard limit is disabled by
default to avoid breaking existing applications that make intensive use
of pipes (eg: for splicing).

Reported-by: socketpair@gmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Mitigates: CVE-2013-4312 (Linux 2.0+)
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Moritz Muehlenhoff <moritz@wikimedia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

QE-UART: add "fsl,t1040-ucc-uart" to of_device_id

commit 11ca2b7ab432eb90906168c327733575e68d388f upstream.

New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.

Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wait/ptrace: assume __WALL if the child is traced

commit bf959931ddb88c4e4366e96dd22e68fa0db9527c upstream.

The following program (simplified version of generated by syzkaller)

#include <pthread.h>
#include <unistd.h>
#include <sys/ptrace.h>
#include <stdio.h>
#include <signal.h>

void *thread_func(void *arg)
{
ptrace(PTRACE_TRACEME, 0,0,0);
return 0;
}

int main(void)
{
pthread_t thread;

if (fork())
return 0;

while (getppid() != 1)
;

pthread_create(&thread, NULL, thread_func, NULL);
pthread_join(thread, NULL);
return 0;
}

creates an unreapable zombie if /sbin/init doesn't use __WALL.

This is not a kernel bug, at least in a sense that everything works as
expected: debugger should reap a traced sub-thread before it can reap the
leader, but without __WALL/__WCLONE do_wait() ignores sub-threads.

Unfortunately, it seems that /sbin/init in most (all?) distributions
doesn't use it and we have to change the kernel to avoid the problem.
Note also that most init's use sys_waitid() which doesn't allow __WALL, so
the necessary user-space fix is not that trivial.

This patch just adds the "ptrace" check into eligible_child().  To some
degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is
mostly ignored when the tracee reports to debugger.  Or WSTOPPED, the
tracer doesn't need to set this flag to wait for the stopped tracee.

This obviously means the user-visible change: __WCLONE and __WALL no
longer have any meaning for debugger.  And I can only hope that this won't
break something, but at least strace/gdb won't suffer.

We could make a more conservative change.  Say, we can take __WCLONE into
account, or !thread_group_leader().  But it would be nice to not
complicate these historical/confusing checks.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: <syzkaller@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: use phys_addr_t for reserve_bootmem_region() arguments

commit 4b50bcc7eda4d3cc9e3f2a0aa60e590fedf728c5 upstream.

Since commit 92923ca3aace ("mm: meminit: only set page reserved in the
memblock region") the reserved bit is set on reserved memblock regions.
However start and end address are passed as unsigned long.  This is only
32bit on i386, so it can end up marking the wrong pages reserved for
ranges at 4GB and above.

This was observed on a 32bit Xen dom0 which was booted with initial
memory set to a value below 4G but allowing to balloon in memory
(dom0_mem=1024M for example).  This would define a reserved bootmem
region for the additional memory (for example on a 8GB system there was
a reverved region covering the 4GB-8GB range).  But since the addresses
were passed on as unsigned long, this was actually marking all pages
from 0 to 4GB as reserved.

Fixes: 92923ca3aacef63 ("mm: meminit: only set page reserved in the memblock region")
Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.com
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: v4l2-compat-ioctl32: fix missing reserved field copy in put_v4l2_create32

commit baf43c6eace43868e490f18560287fa3481b2159 upstream.

In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved
filed of v4l2_create_buffers filled with zero
Reserved field is filled with zero in v4l_create_bufs.
This patch copy reserved field of v4l2_create_buffer from kernel space to user
space

Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Disable all BAR sizing for devices with non-compliant BARs

commit ad67b437f187ea818b2860524d10f878fadfdd99 upstream.

b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec.  But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:

  pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]

Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.

Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check.  We haven't had reports of devices with broken SR-IOV
BARs yet.

[bhelgaas: changelog]
Fixes: b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range

commit 71324fdc72ef0163e57631aa814a9a81e9e4770b upstream.

The range is registered into a linked list which can be referenced
throughout the lifetime of the driver. Ensure the range's memory is useful
for the same lifetime by adding it to the driver's private data structure.

The bug was introduced in the driver's initial commit, which was present in
v3.10.

Fixes: f0b9a7e521fa ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: bcm2835: divider value has to be 1 or more

commit 997f16bd5d2e9b3456027f96fcadfe1e2bf12f4e upstream.

Current clamping of a normal divider allows a value < 1 to be valid.

A divider of < 1 would actually only be possible if we had a PLL...

So this patch clamps the divider to 1.

Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
audio domain clocks")

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: bcm2835: pll_off should only update CM_PLL_ANARST

commit 6727f086cfe4ddcc651eb2bf4301abfcf619be06 upstream.

bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control
register, which may lose the other bits that are currently set by the
clock dividers.

It also now locks during the read/modify/write cycle of both
registers.

Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
audio domain clocks")

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: at91: fix check of clk_register() returned value

commit cb0ceaf77d93964a0d00477c79f4499123f6159c upstream.

The clk_register() function returns a valid pointer to struct clk or
ERR_PTR() error code, this makes a check for returned NULL value
useless and may lead to oops on error path.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: bcc5fd49a0fd ("clk: at91: add a driver for the h32mx clock")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: bcm2835: Fix PLL poweron

commit e708b383f4b94feca2e0d5d06e1cfc13cdfea100 upstream.

In poweroff, we set the reset bit and the power down bit, but only
managed to unset the reset bit for poweron.  This meant that if HDMI
did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the
PLLH (that had been on at boot time) and never recover.

Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpuidle: Fix cpuidle_state_is_coupled() argument in cpuidle_enter()

commit e7387da52028b072489c45efeb7a916c0205ebd2 upstream.

Commit 0b89e9aa2856 (cpuidle: delay enabling interrupts until all
coupled CPUs leave idle) rightfully fixed a regression by letting
the coupled idle state framework to handle local interrupt enabling
when the CPU is exiting an idle state.

The current code checks if the idle state is coupled and, if so, it
will let the coupled code to enable interrupts. This way, it can
decrement the ready-count before handling the interrupt. This
mechanism prevents the other CPUs from waiting for a CPU which is
handling interrupts.

But the check is done against the state index returned by the back
end driver's ->enter functions which could be different from the
initial index passed as parameter to the cpuidle_enter_state()
function.

 entered_state = target_state->enter(dev, drv, index);

 [ ... ]

 if (!cpuidle_state_is_coupled(drv, entered_state))
local_irq_enable();

 [ ... ]

If the 'index' is referring to a coupled idle state but the
'entered_state' is *not* coupled, then the interrupts are enabled
again. All CPUs blocked on the sync barrier may busy loop longer
if the CPU has interrupts to handle before decrementing the
ready-count. That's consuming more energy than saving.

Fixes: 0b89e9aa2856 (cpuidle: delay enabling interrupts until all coupled CPUs leave idle)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpuidle: Indicate when a device has been unregistered

commit c998c07836f985b24361629dc98506ec7893e7a0 upstream.

Currently the 'registered' member of the cpuidle_device struct is set
to 1 during cpuidle_register_device. In this same function there are
checks to see if the device is already registered to prevent duplicate
calls to register the device, but this value is never set to 0 even on
unregister of the device. Because of this, any attempt to call
cpuidle_register_device after a call to cpuidle_unregister_device will
fail which shouldn't be the case.

To prevent this, set registered to 0 when the device is unregistered.

Fixes: c878a52d3c7c (cpuidle: Check if device is already registered)
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM / Runtime: Fix error path in pm_runtime_force_resume()

commit 0ae3aeefabbeef26294e7a349b51f1c761d46c9f upstream.

As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.

Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.

Fixes: 37f204164dfb (PM: Add pm_runtime_suspend|resume_force functions)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: intel_soc_pmic_core: Terminate panel control GPIO lookup table correctly

commit 36e6d081cfb2cb64e6d8e5121cffb1e62f894d36 upstream.

GPIO lookup tables are supposed to be zero terminated. Let's do that
and avoid accidentally walking off the end.

Fixes: 61dd2ca2d44e ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mfd: intel-lpss: Save register context on suspend

commit 41a3da2b8e1639d983192e3650670df4ecc94cf7 upstream.

All configurations are lost and the registers will have
default values when the hardware is suspended and resumed,
so saving the private register space context on suspend, and
restoring it on resume.

Fixes: 4b45efe85263 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (ads7828) Enable internal reference

commit 7a18afe8097731b8ffb6cb5b2b3b418ded77c105 upstream.

On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.

Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aacraid: Fix for KDUMP driver hang

commit 78cbccd3bd683c295a44af8050797dc4a41376ff upstream.

When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.

Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.

Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aacraid: Fix for aac_command_thread hang

commit fc4bf75ea300a5e62a2419f89dd0e22189dd7ab7 upstream.

Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.

In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.

The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.

Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aacraid: Relinquish CPU during timeout wait

commit 07beca2be24cc710461c0b131832524c9ee08910 upstream.

aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.

Fixed by replacing "cpu_relax()" call with "schedule()"
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: pci: use dev_kfree_skb_irq instead of kfree_skb in rtl_pci_reset_trx_ring

commit cf968937d27751296920e6b82ffa89735e3a0023 upstream.

We can't use kfree_skb in irq disable context, because spin_lock_irqsave
make sure we are always in irq disable context, use dev_kfree_skb_irq
instead of kfree_skb is better than dev_kfree_skb_any.

This patch fix below kernel warning:
[ 7612.095528] ------------[ cut here ]------------
[ 7612.095546] WARNING: CPU: 3 PID: 4460 at kernel/softirq.c:150 __local_bh_enable_ip+0x58/0x80()
[ 7612.095550] Modules linked in: rtl8723be x86_pkg_temp_thermal btcoexist rtl_pci rtlwifi rtl8723_common
[ 7612.095567] CPU: 3 PID: 4460 Comm: ifconfig Tainted: G        W       4.4.0+ #4
[ 7612.095570] Hardware name: LENOVO 20DFA04FCD/20DFA04FCD, BIOS J5ET48WW (1.19 ) 08/27/2015
[ 7612.095574]  00000000 00000000 da37fc70 c12ce7c5 00000000 da37fca0 c104cc59 c19d4454
[ 7612.095584]  00000003 0000116c c19d4784 00000096 c10508a8 c10508a8 00000200 c1b42400
[ 7612.095594]  f29be780 da37fcb0 c104ccad 00000009 00000000 da37fcbc c10508a8 f21f08b8
[ 7612.095604] Call Trace:
[ 7612.095614]  [<c12ce7c5>] dump_stack+0x41/0x5c
[ 7612.095620]  [<c104cc59>] warn_slowpath_common+0x89/0xc0
[ 7612.095628]  [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80
[ 7612.095634]  [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80
[ 7612.095640]  [<c104ccad>] warn_slowpath_null+0x1d/0x20
[ 7612.095646]  [<c10508a8>] __local_bh_enable_ip+0x58/0x80
[ 7612.095653]  [<c16b7d34>] destroy_conntrack+0x64/0xa0
[ 7612.095660]  [<c16b300f>] nf_conntrack_destroy+0xf/0x20
[ 7612.095665]  [<c1677565>] skb_release_head_state+0x55/0xa0
[ 7612.095670]  [<c16775bb>] skb_release_all+0xb/0x20
[ 7612.095674]  [<c167760b>] __kfree_skb+0xb/0x60
[ 7612.095679]  [<c16776f0>] kfree_skb+0x30/0x70
[ 7612.095686]  [<f81b869d>] ? rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci]
[ 7612.095692]  [<f81b869d>] rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci]
[ 7612.095698]  [<f81b87f9>] rtl_pci_start+0x19/0x190 [rtl_pci]
[ 7612.095705]  [<f81970e6>] rtl_op_start+0x56/0x90 [rtlwifi]
[ 7612.095712]  [<c17e3f16>] drv_start+0x36/0xc0
[ 7612.095717]  [<c17f5ab3>] ieee80211_do_open+0x2d3/0x890
[ 7612.095725]  [<c16820fe>] ? call_netdevice_notifiers_info+0x2e/0x60
[ 7612.095730]  [<c17f60bd>] ieee80211_open+0x4d/0x50
[ 7612.095736]  [<c16891b3>] __dev_open+0xa3/0x130
[ 7612.095742]  [<c183fa53>] ? _raw_spin_unlock_bh+0x13/0x20
[ 7612.095748]  [<c1689499>] __dev_change_flags+0x89/0x140
[ 7612.095753]  [<c127c70d>] ? selinux_capable+0xd/0x10
[ 7612.095759]  [<c1689589>] dev_change_flags+0x29/0x60
[ 7612.095765]  [<c1700b93>] devinet_ioctl+0x553/0x670
[ 7612.095772]  [<c12db758>] ? _copy_to_user+0x28/0x40
[ 7612.095777]  [<c17018b5>] inet_ioctl+0x85/0xb0
[ 7612.095783]  [<c166e647>] sock_ioctl+0x67/0x260
[ 7612.095788]  [<c166e5e0>] ? sock_fasync+0x80/0x80
[ 7612.095795]  [<c115c99b>] do_vfs_ioctl+0x6b/0x550
[ 7612.095800]  [<c127c812>] ? selinux_file_ioctl+0x102/0x1e0
[ 7612.095807]  [<c10a8914>] ? timekeeping_suspend+0x294/0x320
[ 7612.095813]  [<c10a256a>] ? __hrtimer_run_queues+0x14a/0x210
[ 7612.095820]  [<c1276e24>] ? security_file_ioctl+0x34/0x50
[ 7612.095827]  [<c115cef0>] SyS_ioctl+0x70/0x80
[ 7612.095832]  [<c1001804>] do_fast_syscall_32+0x84/0x120
[ 7612.095839]  [<c183ff91>] sysenter_past_esp+0x36/0x55
[ 7612.095844] ---[ end trace 97e9c637a20e8348 ]---

Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: Fix logic error in enter/exit power-save mode

commit 873ffe154ae074c46ed2d72dbd9a2a99f06f55b4 upstream.

In commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue"), the tests for enter/exit
power-save mode were inverted. With this change applied, the
wifi connection becomes much more stable.

Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: btcoexist: Implement antenna selection

commit baa1702290953295e421f0f433e2b1ff4815827c upstream.

The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8723be: Add antenna select module parameter

commit c18d8f5095715c56bb3cd9cba64242542632054b upstream.

A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.

A fix involving a new module parameter has been developed.  This commit
adds the new parameter and implements the changes needed for the driver.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwrng: exynos - Fix unbalanced PM runtime put on timeout error path

commit f1925d78d7b710a1179828d53e918295f5f5d222 upstream.

In case of timeout during read operation, the exit path lacked PM
runtime put. This could lead to unbalanced runtime PM usage counter thus
leaving the device in an active state.

Fixes: d7fd6075a205 ("hwrng: exynos - Add timeout for waiting on init done")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath5k: Change led pin configuration for compaq c700 laptop

commit 7b9bc799a445aea95f64f15e0083cb19b5789abe upstream.

BugLink: http://bugs.launchpad.net/bugs/972604
Commit 09c9bae26b0d3c9472cb6ae45010460a2cee8b8d ("ath5k: add led pin
configuration for compaq c700 laptop") added a pin configuration for the Compaq
c700 laptop.  However, the polarity of the led pin is reversed.  It should be
red for wifi off and blue for wifi on, but it is the opposite.  This bug was
reported in the following bug report:
http://pad.lv/972604

Fixes: 09c9bae26b0d3c9472cb6ae45010460a2cee8b8d ("ath5k: add led pin configuration for compaq c700 laptop")
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: fix kernel panic, move arvifs list head init before htt init

commit 4ad24a9d83bd4bf0a85e95bf144e18d3fda4fbf1 upstream.

It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.

This patch initilizes the arvifs list before initilizing htt.

Fixes the below issue:
 [<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
 [<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
 [<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
 [<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
 [<c0234100>] (tasklet_action+0x8c/0xec)
 [<c0234100>] (tasklet_action)
 [<c02337c0>] (__do_softirq+0xf8/0x228)
 [<c02337c0>] (__do_softirq)  [<c0233920>] (run_ksoftirqd+0x30/0x90)
 Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
 ---[ end trace 71de5c2e011dbf56 ]---
 Kernel panic - not syncing: Fatal exception in interrupt

Fixes: 500ff9f9389d ("ath10k: implement chanctx API")
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: fix rx_channel during hw reconfigure

commit 1ce8c1484e80010a6e4b9611c65668ff77556f45 upstream.

Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: fix firmware assert in monitor mode

commit 8a75fc54745fd3ce9062ab1cc6429a9da9ac2a68 upstream.

commit 166de3f1895d ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f1895d ("ath10k: remove supported chain mask").

ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up

This issue is originally reported on qca9888 with 10.1 firmware.

Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath10k: fix debugfs pktlog_filter write

commit 9ddc486aa09a3413a6c492fcf160ce61bfccb7b1 upstream.

It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.

Fixes: 90174455ae05 ("ath10k: add support to configure pktlog filter")
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.

commit 0f9edcdd88a993914fa1d1dc369b35dc503979db upstream.

The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity
(active high instead of active low).

The same PCI Subsystem ID is used by both cards, which are based on
the same Atheros MB92 design.

Cc: <linux-wireless@vger.kernel.org>
Cc: <ath9k-devel@qca.qualcomm.com>
Cc: <ath9k-devel@lists.ath9k.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k: Add a module parameter to invert LED polarity.

commit cd84042ce9040ad038e958bc67a46fcfc015c736 upstream.

The LED can be active high instead of active low on some hardware.

Add the led_active_high module parameter. It defaults to -1 to obey
platform data as before.

Setting the parameter to 1 or 0 will force the LED respectively
active high or active low.

Cc: <linux-wireless@vger.kernel.org>
Cc: <ath9k-devel@qca.qualcomm.com>
Cc: <ath9k-devel@lists.ath9k.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: imx35: restore existing used clock enumeration

commit 3397c2c45b1b6f54834dfeae30a73046f33ca943 upstream.

A new element got inserted into enum mx35_clks with commit 3713e3f5e927
("clk: imx35: define two clocks for rtc"). This insertion shifted most
nummerical clock assignments to a new nummerical value which in turn
rendered most hardcoded nummeric values in imx35.dtsi incorrect.

Restore the existing order by moving the newly introduced clock to the
end of the enum. Update the dts documentation accordingly.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Fixes: 3713e3f5e927 ("clk: imx35: define two clocks for rtc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats

commit 330d12764e15f6e3e94ff34cda29db96d2589c24 upstream.

MAX8997 PMIC requires interrupt and fails probing without it.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: d105f0b1215d ("ARM: dts: Add basic dts file for Samsung Trats board")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: at91: fix typo in sama5d2 PIN_PD24 description

commit b1f3a3b03eb5f61b4051e2da9aa15653e705e111 upstream.

Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were
wrongly linked to PIN_PD23).

Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
[nicolas.ferre@atmel.com: add commit message, changed subject]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: mvebu: fix GPIO config on the Linksys boards

commit 9800917cf92f5b5fe5cae706cb70db8d014f663c upstream.

Some of the GPIO configs were wrong in the submitted DTS files,
this patch fixes all affected boards.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Input: uinput - handle compat ioctl for UI_SET_PHYS

commit affa80bd97f7ca282d1faa91667b3ee9e4c590e6 upstream.

When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.

Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ak4642: Enable cache usage to fix crashes on resume

commit d3030d11961a8c103cf07aed59905276ddfc06c2 upstream.

The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap.  Fix this by enabling
caching.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

affs: fix remount failure when there are no options changed

commit 01d6e08711bf90bc4d7ead14a93a0cbd73b1896a upstream.

Commit c8f33d0bec99 ("affs: kstrdup() memory handling") checks if the
kstrdup function returns NULL due to out-of-memory condition.

However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL.  In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists.  The mount syscall then fails with
ENOMEM.

This patch fixes the bug.  We fail with ENOMEM only if data is non-NULL.

The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).

Fixes: c8f33d0bec99 ("affs: kstrdup() memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: VDSO: Build with `-fno-strict-aliasing'

commit 94cc36b84acc29f543b48bc5ed786011b112a666 upstream.

Avoid an aliasing issue causing a build error in VDSO:

In file included from include/linux/srcu.h:34:0,
                 from include/linux/notifier.h:15,
                 from ./arch/mips/include/asm/uprobes.h:9,
                 from include/linux/uprobes.h:61,
                 from include/linux/mm_types.h:13,
                 from ./arch/mips/include/asm/vdso.h:14,
                 from arch/mips/vdso/vdso.h:27,
                 from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
  return *work_data_bits(work) & WORK_STRUCT_STATIC;
  ^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1

with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0.  Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO").

Thanks to Tejun for diagnosing this properly!

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: lib: Mark intrinsics notrace

commit aedcfbe06558a9f53002e82d5be64c6c94687726 upstream.

On certain MIPS32 devices, the ftrace tracer "function_graph" uses
__lshrdi3() during the capturing of trace data. ftrace then attempts to
trace __lshrdi3() which leads to infinite recursion and a stack overflow.
Fix this by marking __lshrdi3() as notrace. Mark the other compiler
intrinsics as notrace in case the compiler decides to use them in the
ftrace path.

Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/13354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Build microMIPS VDSO for microMIPS kernels

commit bb93078e655be1e24d68f28f2756676e62c037ce upstream.

MicroMIPS kernels may be expected to run on microMIPS only cores which
don't support the normal MIPS instruction set, so be sure to pass the
-mmicromips flag through to the VDSO cflags.

Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix sigreturn via VDSO on microMIPS kernel

commit 13eb192d10bcc9ac518d57356179071d603bcb4e upstream.

In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.

However commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.

Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.

Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ptrace: Prevent writes to read-only FCSR bits

commit abf378be49f38c4d3e23581d3df3fa9f1b1b11d2 upstream.

Correct the cases missed with commit 9b26616c8d9d ("MIPS: Respect the
ISA level in FCSR handling") and prevent writes to read-only FCSR bits
there.

This in particular applies to FP context initialisation where any IEEE
754-2008 bits preset by `mips_set_personality_nan' are cleared before
the relevant ptrace(2) call takes effect and the PTRACE_POKEUSR request
addressing FPC_CSR where no masking of read-only FCSR bits is done.

Remove the FCSR clearing from FP context initialisation then and unify
PTRACE_POKEUSR/FPC_CSR and PTRACE_SETFPREGS handling, by factoring out
code from `ptrace_setfpregs' and calling it from both places.

This mostly matters to soft float configurations where the emulator can
be switched this way to a mode which should not be accessible and cannot
be set with the CTC1 instruction.  With hard float configurations any
effect is transient anyway as read-only bits will retain their values at
the time the FP context is restored.

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ptrace: Fix FP context restoration FCSR regression

commit 4249548454f7ba4581aeee26bd83f42b48a14d15 upstream.

Fix a floating-point context restoration regression introduced with
commit 9b26616c8d9d ("MIPS: Respect the ISA level in FCSR handling")
that causes a Floating Point exception and consequently a kernel oops
with hard float configurations when one or more FCSR Enable and their
corresponding Cause bits are set both at a time via a ptrace(2) call.

To do so reinstate Cause bit masking originally introduced with commit
b1442d39fac2 ("MIPS: Prevent user from setting FCSR cause bits") to
address this exact problem and then inadvertently removed from the
PTRACE_SETFPREGS request with the commit referred above.

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Disable preemption during prctl(PR_SET_FP_MODE, ...)

commit bd239f1e1429e7781096bf3884bdb1b2b1bb4f28 upstream.

Whilst a PR_SET_FP_MODE prctl is performed there are decisions made
based upon whether the task is executing on the current CPU. This may
change if we're preempted, so disable preemption to avoid such changes
for the lifetime of the mode switch.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13144/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Prevent "restoration" of MSA context in non-MSA kernels

commit 6533af4d4831c421cd9aa4dce7cfc19a3514cc09 upstream.

If a kernel doesn't support MSA context (ie. CONFIG_CPU_HAS_MSA=n) then
it will only keep 64 bits per FP register in thread context, and the
calls to set_fpr64 in restore_msa_extcontext will overrun the end of the
FP register context into the FCSR & MSACSR values. GCC 6.x has become
smart enough to detect this & complain like so:

    arch/mips/kernel/signal.c: In function 'protected_restore_fp_context':
    ./arch/mips/include/asm/processor.h:114:17: error: array subscript is above array bounds [-Werror=array-bounds]
      fpr->val##width[FPR_IDX(width, idx)] = val;   \
      ~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
    ./arch/mips/include/asm/processor.h:118:1: note: in expansion of macro 'BUILD_FPR_ACCESS'
     BUILD_FPR_ACCESS(64)

The only way to trigger this code to run would be for a program to set
up an artificial extended MSA context structure following a sigframe &
execute sigreturn. Whilst this doesn't allow a program to write to any
state that it couldn't already, it makes little sense to allow this
"restoration" of MSA context in a system that doesn't support MSA.

Fix this by killing a program with SIGSYS if it tries something as crazy
as "restoring" fake MSA context in this way, also fixing the build error
& allowing for most of restore_msa_extcontext to be optimised out of
kernels without support for MSA.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Michal Toman <michal.toman@imgtec.com>
Fixes: bf82cb30c7e5 ("MIPS: Save MSA extended context around signals")
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Toman <michal.toman@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix MSA ld_*/st_* asm macros to use PTR_ADDU

commit ea1688573426adc2587ed52d086b51c7c62eaca3 upstream.

The MSA ld_*/st_* assembler macros for when the toolchain doesn't
support MSA use addu to offset the base address. However it is a virtual
memory pointer so fix it to use PTR_ADDU which expands to daddu for
64-bit kernels.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13062/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Use copy_s.fmt rather than copy_u.fmt

commit 8a3c8b48aca8771bff3536e40aa26ffb311699d1 upstream.

In revision 1.12 of the MSA specification, the copy_u.w instruction has
been removed for MIPS32 & the copy_u.d instruction has been removed for
MIPS64. Newer toolchains (eg. Codescape SDK essentials 2015.10) will
complain about this like so:

arch/mips/kernel/r4k_fpu.S:290: Error: opcode not supported on this
processor: mips32r2 (mips32r2) `copy_u.w $1,$w26[3]'

Since we always copy to the width of a GPR, simply use copy_s instead of
copy_u to fix this.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13061/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Loongson-3: Reserve 32MB for RS780E integrated GPU

commit 3484de7bcbed20ecbf2b8d80671619e7059e2dd7 upstream.

Due to datasheet, reserving 0xff800000~0xffffffff (8MB below 4GB) is
not enough for RS780E integrated GPU's TOM (top of memory) registers
and MSI/MSI-x memory region, so we reserve 0xfe000000~0xffffffff (32MB
below 4GB).

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12889/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Reserve nosave data for hibernation

commit a95d069204e178f18476f5499abab0d0d9cbc32c upstream.

After commit 92923ca3aacef63c92d ("mm: meminit: only set page reserved
in the memblock region"), the MIPS hibernation is broken. Because pages
in nosave data section should be "reserved", but currently they aren't
set to "reserved" at initialization. This patch makes hibernation work
again.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12888/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ath79: make bootconsole wait for both THRE and TEMT

commit f5b556c94c8490d42fea79d7b4ae0ecbc291e69d upstream.

This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.

Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.

In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.

A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Sync icache & dcache in set_pte_at

commit 37d22a0d798b5c938b277d32cfd86dc231381342 upstream.

It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:

    CPU0                            CPU1

    write to page
    flush_dcache_page
    flush_icache_page
    set_pte_at
                                    map page
    update_mmu_cache

If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.

To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.

When forking a process:

[   15.271842] [<80417630>] __update_cache+0xcc/0x188
[   15.277274] [<80530394>] copy_page_range+0x56c/0x6ac
[   15.282861] [<8042936c>] copy_process.part.54+0xd40/0x17ac
[   15.289028] [<80429f80>] do_fork+0xe4/0x420
[   15.293747] [<80413808>] handle_sys+0x128/0x14c

When exec'ing an ELF binary:

[   14.445964] [<80417630>] __update_cache+0xcc/0x188
[   14.451369] [<80538d88>] move_page_tables+0x414/0x498
[   14.457075] [<8055d848>] setup_arg_pages+0x220/0x318
[   14.462685] [<805b0f38>] load_elf_binary+0x530/0x12a0
[   14.468374] [<8055ec3c>] search_binary_handler+0xbc/0x214
[   14.474444] [<8055f6c0>] do_execveat_common+0x43c/0x67c
[   14.480324] [<8055f938>] do_execve+0x38/0x44
[   14.485137] [<80413808>] handle_sys+0x128/0x14c

These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.

Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Fixes: 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12722/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Handle highmem pages in __update_cache

commit f4281bba818105c7c91799abe40bc05c0dbdaa25 upstream.

The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12721/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Flush highmem pages in __flush_dcache_page

commit 234859e49a15323cf1b2331bdde7f658c4cb45fb upstream.

When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).

This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix watchpoint restoration

commit a7e89326b415b5d81c4b1016fd4a40db861eb58d upstream.

Commit f51246efee2b ("MIPS: Get rid of finish_arch_switch().") moved the
__restore_watch() call from finish_arch_switch() (i.e. after resume()
returns) to before the resume() call in switch_to(). This results in
watchpoints only being restored when a task is descheduled, preventing
the watchpoints from being effective most of the time, except due to
chance before the watchpoints are lazily removed.

Fix the call sequence from switch_to() through to
mips_install_watch_registers() to pass the task_struct pointer of the
next task, instead of using current. This allows the watchpoints for the
next (non-current) task to be restored without reintroducing
finish_arch_switch().

Fixes: f51246efee2b ("MIPS: Get rid of finish_arch_switch().")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix uapi include in exported asm/siginfo.h

commit 987e5b834467c9251ca584febda65ef8f66351a9 upstream.

Since commit 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.

Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.

Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix siginfo.h to use strict posix types

commit 5daebc477da4dfeb31ae193d83084def58fd2697 upstream.

Commit 85efde6f4e0d ("make exported headers use strict posix types")
changed the asm-generic siginfo.h to use the __kernel_* types, and
commit 3a471cbc081b ("remove __KERNEL_STRICT_NAMES") make the internal
types accessible only to the kernel, but the MIPS implementation hasn't
been updated to match.

Switch to proper types now so that the exported asm/siginfo.h won't
produce quite so many compiler errors when included alone by a user
program.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12477/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Avoid using unwind_stack() with usermode

commit 81a76d7119f63c359750e4adeff922a31ad1135f upstream.

When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.

Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Don't unwind to user mode with EVA

commit a816b306c62195b7c43c92cb13330821a96bdc27 upstream.

When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.

Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).

I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).

However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC

commit e49d38488515057dba8f0c2ba4cfde5be4a7281f upstream.

Fix a build regression from commit c9017757c532 ("MIPS: init upper 64b
of vector registers when MSA is first used"):

arch/mips/built-in.o: In function `enable_restore_fp_context':
traps.c:(.text+0xbb90): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbb90): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'
traps.c:(.text+0xbef0): undefined reference to `_init_msa_upper'
traps.c:(.text+0xbef0): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper'

to !CONFIG_CPU_HAS_MSA configurations with older GCC versions, which are
unable to figure out that calls to `_init_msa_upper' are indeed dead.
Of the many ways to tackle this failure choose the approach we have
already taken in `thread_msa_context_live'.

[ralf@linux-mips.org: Drop patch segment to junk file.]

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: math-emu: Fix jalr emulation when rd == $0

commit ab4a92e66741b35ca12f8497896bafbe579c28a1 upstream.

When emulating a jalr instruction with rd == $0, the code in
isBranchInstr was incorrectly writing to GPR $0 which should actually
always remain zeroed. This would lead to any further instructions
emulated which use $0 operating on a bogus value until the task is next
context switched, at which point the value of $0 in the task context
would be restored to the correct zero by a store in SAVE_SOME. Fix this
by not writing to rd if it is $0.

Fixes: 102cedc32a6e ("MIPS: microMIPS: Floating point support.")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS64: R6: R2 emulation bugfix

commit 41fa29e4d8cf4150568a0fe9bb4d62229f9caed5 upstream.

Error recovery pointers for fixups was improperly set as ".word"
which is unsuitable for MIPS64.

Replaced by STR(PTR)

[ralf@linux-mips.org: Apply changes as requested in the review process.]

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: b0a668fb2038 ("MIPS: kernel: mips-r2-to-r6-emul: Add R2 emulator for MIPS R6")
Cc: macro@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.12

kbuild: move -Wunused-const-variable to W=1 warning level

commit c9c6837d39311b0cc14cdbe7c18e815ab44aefb1 upstream.

gcc-6 started warning by default about variables that are not
used anywhere and that are marked 'const', generating many
false positives in an allmodconfig build, e.g.:

arch/arm/mach-davinci/board-da830-evm.c:282:20: warning: 'da830_evm_emif25_pins' defined but not used [-Wunused-const-variable=]
arch/arm/plat-omap/dmtimer.c:958:34: warning: 'omap_timer_match' defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:625:39: warning: 'acpi_bcm_default_gpios' defined but not used [-Wunused-const-variable=]
drivers/char/hw_random/omap-rng.c:92:18: warning: 'reg_map_omap4' defined but not used [-Wunused-const-variable=]
drivers/devfreq/exynos/exynos5_bus.c:381:32: warning: 'exynos5_busfreq_int_pm' defined but not used [-Wunused-const-variable=]
drivers/dma/mv_xor.c:1139:34: warning: 'mv_xor_dt_ids' defined but not used [-Wunused-const-variable=]

This is similar to the existing -Wunused-but-set-variable warning
that was added in an earlier release and that we disable by default
now and only enable when W=1 is set, so it makes sense to do
the same here. Once we have eliminated the majority of the
warnings for both, we can put them back into the default list.

We probably want this in backport kernels as well, to allow building
them with gcc-6 without introducing extra warnings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "scsi: fix soft lockup in scsi_remove_target() on module removal"

commit 305c2e71b3d733ec065cb716c76af7d554bd5571 upstream.

Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit
90a88d6ef88e ("scsi: fix soft lockup in scsi_remove_target() on module
removal").

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: Add intermediate STARGET_REMOVE state to scsi_target_state

commit f05795d3d771f30a7bdc3a138bf714b06d42aa95 upstream.

Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.

This re-fixes the problem introduced in commits bc3f02a795d3 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and
40998193560d ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.

[mkp: Included James' fix for scsi_target_destroy()]

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hpfs: implement the show_options method

commit 037369b872940cd923835a0a589763180c4a36bc upstream.

The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts.  However, there is a problem that the options
may disappear after remount.  If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.

To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hpfs: fix remount failure when there are no options changed

commit 44d51706b4685f965cd32acde3fe0fcc1e6198e8 upstream.

Commit ce657611baf9 ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.

However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL.  In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists.  The mount syscall then fails with
ENOMEM.

This patch fixes the bug.  We fail with ENOMEM only if data is non-NULL.

The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).

Fixes: ce657611baf9 ("hpfs: kstrdup() out of memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UBI: Fix static volume checks when Fastmap is used

commit 1900149c835ab5b48bea31a823ea5e5a401fb560 upstream.

Ezequiel reported that he's facing UBI going into read-only
mode after power cut. It turned out that this behavior happens
only when updating a static volume is interrupted and Fastmap is
used.

A possible trace can look like:
ubi0 warning: ubi_io_read_vid_hdr [ubi]: no VID header found at PEB 2323, only 0xFF bytes
ubi0 warning: ubi_eba_read_leb [ubi]: switch to read-only mode
CPU: 0 PID: 833 Comm: ubiupdatevol Not tainted 4.6.0-rc2-ARCH #4
Hardware name: SAMSUNG ELECTRONICS CO., LTD. 300E4C/300E5C/300E7C/NP300E5C-AD8AR, BIOS P04RAP 10/15/2012
0000000000000286 00000000eba949bd ffff8800c45a7b38 ffffffff8140d841
ffff8801964be000 ffff88018eaa4800 ffff8800c45a7bb8 ffffffffa003abf6
ffffffff850e2ac0 8000000000000163 ffff8801850e2ac0 ffff8801850e2ac0
Call Trace:
[<ffffffff8140d841>] dump_stack+0x63/0x82
[<ffffffffa003abf6>] ubi_eba_read_leb+0x486/0x4a0 [ubi]
[<ffffffffa00453b3>] ubi_check_volume+0x83/0xf0 [ubi]
[<ffffffffa0039d97>] ubi_open_volume+0x177/0x350 [ubi]
[<ffffffffa00375d8>] vol_cdev_open+0x58/0xb0 [ubi]
[<ffffffff8124b08e>] chrdev_open+0xae/0x1d0
[<ffffffff81243bcf>] do_dentry_open+0x1ff/0x300
[<ffffffff8124afe0>] ? cdev_put+0x30/0x30
[<ffffffff81244d36>] vfs_open+0x56/0x60
[<ffffffff812545f4>] path_openat+0x4f4/0x1190
[<ffffffff81256621>] do_filp_open+0x91/0x100
[<ffffffff81263547>] ? __alloc_fd+0xc7/0x190
[<ffffffff812450df>] do_sys_open+0x13f/0x210
[<ffffffff812451ce>] SyS_open+0x1e/0x20
[<ffffffff81a99e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4

UBI checks static volumes for data consistency and reads the
whole volume upon first open. If the volume is found erroneous
users of UBI cannot read from it, but another volume update is
possible to fix it. The check is performed by running
ubi_eba_read_leb() on every allocated LEB of the volume.
For static volumes ubi_eba_read_leb() computes the checksum of all
data stored in a LEB. To verify the computed checksum it has to read
the LEB's volume header which stores the original checksum.
If the volume header is not found UBI treats this as fatal internal
error and switches to RO mode. If the UBI device was attached via a
full scan the assumption is correct, the volume header has to be
present as it had to be there while scanning to get known as mapped.
If the attach operation happened via Fastmap the assumption is no
longer correct. When attaching via Fastmap UBI learns the mapping
table from Fastmap's snapshot of the system state and not via a full
scan. It can happen that a LEB got unmapped after a Fastmap was
written to the flash. Then UBI can learn the LEB still as mapped and
accessing it returns only 0xFF bytes. As UBI is not a FTL it is
allowed to have mappings to empty PEBs, it assumes that the layer
above takes care of LEB accounting and referencing.
UBIFS does so using the LEB property tree (LPT).
For static volumes UBI blindly assumes that all LEBs are present and
therefore special actions have to be taken.

The described situation can happen when updating a static volume is
interrupted, either by a user or a power cut.
The volume update code first unmaps all LEBs of a volume and then
writes LEB by LEB. If the sequence of operations is interrupted UBI
detects this either by the absence of LEBs, no volume header present
at scan time, or corrupted payload, detected via checksum.
In the Fastmap case the former method won't trigger as no scan
happened and UBI automatically thinks all LEBs are present.
Only by reading data from a LEB it detects that the volume header is
missing and incorrectly treats this as fatal error.
To deal with the situation ubi_eba_read_leb() from now on checks
whether we attached via Fastmap and handles the absence of a
volume header like a data corruption error.
This way interrupted static volume updates will correctly get detected
also when Fastmap is used.

Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SIGNAL: Move generic copy_siginfo() to signal.h

commit ca9eb49aa9562eaadf3cea071ec7018ad6800425 upstream.

The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.

It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.

Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Fix double free of drom buffer

commit 2ffa9a5d76a75abbc1f95c17959fced666095bdd upstream.

If tb_drom_read() fails, sw->drom is freed but not set to NULL.  sw->drom
is then freed again in the error path of tb_switch_alloc().

The bug can be triggered by unplugging a thunderbolt device shortly after
it is detected by the thunderbolt driver.

Clear sw->drom if tb_drom_read() fails.

[bhelgaas: add Fixes:, stable versions of interest]
Fixes: 343fcb8c70d7 ("thunderbolt: Fix nontrivial endpoint devices.")
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/srp: Fix a debug kernel crash

commit 54f5c9c52d69afa55abf2b034df8d45f588466c3 upstream.

Avoid that the following BUG() is triggered against a debug
kernel:

kernel BUG at include/linux/scatterlist.h:92!
RIP: 0010:[<ffffffffa0467199>]  [<ffffffffa0467199>] srp_map_idb+0x199/0x1a0 [ib_srp]
Call Trace:
 [<ffffffffa04685fa>] srp_map_data+0x84a/0x890 [ib_srp]
 [<ffffffffa0469674>] srp_queuecommand+0x1e4/0x610 [ib_srp]
 [<ffffffff813f5a5e>] scsi_dispatch_cmd+0x9e/0x180
 [<ffffffff813f8b07>] scsi_request_fn+0x477/0x610
 [<ffffffff81298ffe>] __blk_run_queue+0x2e/0x40
 [<ffffffff81299070>] blk_delay_work+0x20/0x30
 [<ffffffff81071f07>] process_one_work+0x197/0x480
 [<ffffffff81072239>] worker_thread+0x49/0x490
 [<ffffffff810787ea>] kthread+0xea/0x100
 [<ffffffff8159b632>] ret_from_fork+0x22/0x40

Fixes: f7f7aab1a5c0 ("IB/srp: Convert to new registration API")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Fix headset mic detection problem for one Dell machine

commit 86c72d1ce91d804e4fa8d90b316a89597dd220f1 upstream.

Add the pin configuration value of this machine into the pin_quirk
table to make DELL1_MIC_NO_PRESENCE apply to this machine.

Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Add support for ALC295/ALC3254

commit 7d727869c7b86da0874436ac5675dcdadaf3a0a1 upstream.

Add support for ALC295/ALC3254.
They are simply compatible with ALC225 chip.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Fix headphone noise on Dell XPS 13 9360

commit 423cd785619ac6778252fbdb916505aa1c153959 upstream.

The headphone has noise when playing sound or switching microphone sources.
It uses the same codec on XPS 13 9350, but with different subsystem ID.
Applying the fixup can solve the issue.
Also, changing the model name to better differentiate models.

v2: Reorder by device ID.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - New codecs support for ALC234/ALC274/ALC294

commit dcd4f0db6141d6bf2cb897309d5d6f53d1b1696f upstream.

Support new codecs for ALC234/ALC274/ALC294.
This three codecs was the same IC.
But bonding is not the same.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mcb: Fixed bar number assignment for the gdd

commit f75564d343010b025301d9548f2304f48eb25f01 upstream.

The bar number is found in reg2 within the gdd. Therefore
we need to change the assigment from reg1 to reg2 which
is the correct location.

Signed-off-by: Andreas Werner <andreas.werner@men.de>
Fixes: '3764e82e5' drivers: Introduce MEN Chameleon Bus
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: bcm2835: add locking to pll*_on/off methods

commit ec36a5c6682fdd5328abf15c3c67281bed0241d7 upstream.

Add missing locking to:
* bcm2835_pll_divider_on
* bcm2835_pll_divider_off
to protect the read modify write cycle for the
register access protecting both cm_reg and a2w_reg
registers.

Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
audio domain clocks")

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking,qspinlock: Fix spin_is_locked() and spin_unlock_wait()

commit 54cf809b9512be95f53ed4a5e3b631d1ac42f0fa upstream.

Similar to commits:

  51d7d5205d33 ("powerpc: Add smp_mb() to arch_spin_is_locked()")
  d86b8da04dfa ("arm64: spinlock: serialise spin_unlock_wait against concurrent lockers")

qspinlock suffers from the fact that the _Q_LOCKED_VAL store is
unordered inside the ACQUIRE of the lock.

And while this is not a problem for the regular mutual exclusive
critical section usage of spinlocks, it breaks creative locking like:

spin_lock(A) spin_lock(B)
spin_unlock_wait(B) if (!spin_is_locked(A))
do_something()   do_something()

In that both CPUs can end up running do_something at the same time,
because our _Q_LOCKED_VAL store can drop past the spin_unlock_wait()
spin_is_locked() loads (even on x86!!).

To avoid making the normal case slower, add smp_mb()s to the less used
spin_unlock_wait() / spin_is_locked() side of things to avoid this
problem.

Reported-and-tested-by: Davidlohr Bueso <dave@stgolabs.net>
Reported-by: Giovanni Gherdovich <ggherdovich@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: samsung: Reorder the sequence of clock control when call s3c24xx_serial_set_termios()

commit b8995f527aac143e83d3900ff39357651ea4e0f6 upstream.

This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

serial: 8250_mid: recognize interrupt source in handler

commit c42850f1ae7e70056f852e67bb9dddf927853b47 upstream.

There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.

Read the register and call the handlers only for sources that request an
interrupt.

Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_mid: use proper bar for DNV platform

commit 107e15fc1f8d6ef69eac5f175971252f76e82f0d upstream.

Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.

Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_pci: fix divide error bug if baud rate is 0

commit 6f210c18c1c0f016772c8cd51ae12a02bfb9e7ef upstream.

Since commit 21947ba654a6 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654a6 ("serial: 8250_pci: replace switch-case by formula")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix OpenSSH pty regression on close

commit 0f40fbbcc34e093255a2b2d70b6b0fb48c3f39aa upstream.

OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.

This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:

1) f8747d4a466ab2cafe56112c51b3379f9fdb7a12
   tty: Fix pty master read() after slave closes

2) 52bce7f8d4fc633c9a9d0646eef58ba6ae9a3b73
   pty, n_tty: Simplify input processing on final close

3) 1a48632ffed61352a7810ce089dc5a8bcd505a60
   pty: Fix input race when closing

Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net>

Reported-by: Volth <openssh@volth.com>
Reported-by: Marc Aurele La France <tsi@tuyoix.net>
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: atmel: fix hardware handshake selection

commit 5be605ac9af979265d7b64c160ad9928088a78be upstream.

Commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.

As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

TTY: n_gsm, fix false positive WARN_ON

commit d175feca89a1c162f60f4e3560ca7bc9437c65eb upstream.

Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
 [<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
 [<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
 [<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
 [<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
 [<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
 [<     inline     >] tiocsetd drivers/tty/tty_io.c:2650
 [<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...

But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.

Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: vt, return error when con_startup fails

commit 6798df4c5fe0a7e6d2065cf79649a794e5ba7114 upstream.

When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.

So fix the return value to be -ENODEV in that case again.

Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/x86: actually allocate legacy interrupts on PV guests

commit 702f926067d2a4b28c10a3c41a1172dd62d9e735 upstream.

b4ff8389ed14 is incomplete: relies on nr_legacy_irqs() to get the number
of legacy interrupts when actually nr_legacy_irqs() returns 0 after
probe_8259A(). Use NR_IRQS_LEGACY instead.

Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: mask CPUID(0xD,0x1).EAX against host value

commit 316314cae15fb0e3869b76b468f59a0c83ac3d4e upstream.

This ensures that the guest doesn't see XSAVE extensions
(e.g. xgetbv1 or xsavec) that the host lacks.

Cc: stable@vger.kernel.org
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
[4.5 does have CPUID_D_1_EAX, but earlier kernels don't, so use
 the numeric value.  This is consistent with other occurrences
 of cpuid_mask in arch/x86/kvm/cpuid.c - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: KVM: Fix timer IRQ race when writing CP0_Compare

commit b45bacd2d048f405c7760e5cc9b60dd67708734f upstream.

Writing CP0_Compare clears the timer interrupt pending bit
(CP0_Cause.TI), but this wasn't being done atomically. If a timer
interrupt raced with the write of the guest CP0_Compare, the timer
interrupt could end up being pending even though the new CP0_Compare is
nowhere near CP0_Count.

We were already updating the hrtimer expiry with
kvm_mips_update_hrtimer(), which used both kvm_mips_freeze_hrtimer() and
kvm_mips_resume_hrtimer(). Close the race window by expanding out
kvm_mips_update_hrtimer(), and clearing CP0_Cause.TI and setting
CP0_Compare between the freeze and resume. Since the pending timer
interrupt should not be cleared when CP0_Compare is written via the KVM
user API, an ack argument is added to distinguish the source of the
write.

Fixes: e30492bbe95a ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄ\8dmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: KVM: Fix timer IRQ race when freezing timer

commit 4355c44f063d3de4f072d796604c7f4ba4085cc3 upstream.

There's a particularly narrow and subtle race condition when the
software emulated guest timer is frozen which can allow a guest timer
interrupt to be missed.

This happens due to the hrtimer expiry being inexact, so very
occasionally the freeze time will be after the moment when the emulated
CP0_Count transitions to the same value as CP0_Compare (so an IRQ should
be generated), but before the moment when the hrtimer is due to expire
(so no IRQ is generated). The IRQ won't be generated when the timer is
resumed either, since the resume CP0_Count will already match CP0_Compare.

With VZ guests in particular this is far more likely to happen, since
the soft timer may be frozen frequently in order to restore the timer
state to the hardware guest timer. This happens after 5-10 hours of
guest soak testing, resulting in an overflow in guest kernel timekeeping
calculations, hanging the guest. A more focussed test case to
intentionally hit the race (with the help of a new hypcall to cause the
timer state to migrated between hardware & software) hits the condition
fairly reliably within around 30 seconds.

Instead of relying purely on the inexact hrtimer expiry to determine
whether an IRQ should be generated, read the guest CP0_Compare and
directly check whether the freeze time is before or after it. Only if
CP0_Count is on or after CP0_Compare do we check the hrtimer expiry to
determine whether the last IRQ has already been generated (which will
have pushed back the expiry by one timer period).

Fixes: e30492bbe95a ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄ\8dmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: fix ordering of cr0 initialization code in vmx_cpu_reset

commit f24632475d4ffed5626abbfab7ef30a128dd1474 upstream.

Commit d28bc9dd25ce reversed the order of two lines which initialize cr0,
allowing the current (old) cr0 value to mess up vcpu initialization.
This was observed in the checks for cr0 X86_CR0_WP bit in the context of
kvm_mmu_reset_context(). Besides, setting vcpu->arch.cr0 after vmx_set_cr0()
is completely redundant. Change the order back to ensure proper vcpu
initialization.

The combination of booting with ovmf firmware when guest vcpus > 1 and kvm's
ept=N option being set results in a VM-entry failure. This patch fixes that.

Fixes: d28bc9dd25ce ("KVM: x86: INIT and reset sequences are different")
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: MTRR: remove MSR 0x2f8

commit 9842df62004f366b9fed2423e24df10542ee0dc5 upstream.

MSR 0x2f8 accessed the 124th Variable Range MTRR ever since MTRR support
was introduced by 9ba075a664df ("KVM: MTRR support").

0x2f8 became harmful when 910a6aae4e2e ("KVM: MTRR: exactly define the
size of variable MTRRs") shrinked the array of VR MTRRs from 256 to 8,
which made access to index 124 out of bounds.  The surrounding code only
WARNs in this situation, thus the guest gained a limited read/write
access to struct kvm_arch_vcpu.

0x2f8 is not a valid VR MTRR MSR, because KVM has/advertises only 16 VR
MTRR MSRs, 0x200-0x20f.  Every VR MTRR is set up using two MSRs, 0x2f8
was treated as a PHYSBASE and 0x2f9 would be its PHYSMASK, but 0x2f9 was
not implemented in KVM, therefore 0x2f8 could never do anything useful
and getting rid of it is safe.

This fixes CVE-2016-3713.

Fixes: 910a6aae4e2e ("KVM: MTRR: exactly define the size of variable MTRRs")
Reported-by: David Matlack <dmatlack@google.com>
Signed-off-by: Andy Honig <ahonig@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: das1800: fix possible NULL dereference

commit d375278d666760e195693b57415ba0a125cadd55 upstream.

DMA is optional with this driver. If it was not enabled the devpriv->dma
pointer will be NULL.

Fix the possible NULL pointer dereference when trying to disable the DMA
channels in das1800_ai_cancel() and tidy up the comments to fix the
checkpatch.pl issues:
WARNING: line over 80 characters

It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer
will not be used if DMA is disabled but fix it there also.

Fixes: 99dfc3357e98 ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation")
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: udc: core: Fix argument of dev_err() in usb_gadget_map_request()

commit 5096c4d3bfa75bdd23c78f799aabd08598afb48f upstream.

The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.

Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: leave LPM alone if possible when binding/unbinding interface drivers

commit 6fb650d43da3e7054984dc548eaa88765a94d49f upstream.

When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward.  The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters.  This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.

However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary.  The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.

It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs.  Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.

And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: usbtest: fix pattern tests for scatterlists.

commit cdc77c82a8286b1181b81b6e5ef60c8e83ded7bc upstream.

The current implemenentation restart the sent pattern for each entry in
the sg list. The receiving end expects a continuous pattern, and test
will fail unless scatterilst entries happen to be aligned with the
pattern

Fix this by calculating the pattern byte based on total sent size
instead of just the current sg entry.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 8b5249019352 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>