[SCSI] qla2xxx: Reduce request queue-size overhead with recent ISPs.

The original code to 'resize request-queues' based on iocb-counts
and employed during early ISP23xx testing was too
overly-pessimistic with regards to latencies in the firmware
pulling requests.  Recent ISPs can easily keep up processing a
stream of commands from an abbreviated (effectively, half the
original size) queue.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Always use an FLT's NVRAM/VPD region information.

Rather than assuming a particular layout of the data.  Applies to
recent ISPs only.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Drop use of IRQF_DISABLE.

When IRQs are shared by multiple controllers and if the first one
to register does not disable the IRQ, then IRQ will be enabled
for all other controllers by default, irrespective of their
setting. With IRQF_DISABLED registration, the driver interrupt
routine was called with interrupt enabled always. Disbaling the
registration with IRQF_DISABLED, since driver code is re-entrant
safe and all critical sections are guarded with interrupt safe
locks.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add EDC-update support.

Interface allows for the update of onboard EDC firmware
present on mezzanine ISP25xx type cards.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Export flash-block-size for application support.

In handling the RMW semantics needed to update regions not
falling on a sector boundary.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Cleanup unused flags and #defines.

General cleanup of extraneous/legacy crud.

Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Remove implicit ISP-abort after a flash update.

For ISP24xx and above the ISP-abort after flash update is not
needed, as the only purpose it was serving was to update the boot
code and firmware versions in the scsi_qla_host_t structure.  Now
an update of the versions will be done in the write-vpd path.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add reset capabilities for application support.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct ISP abort semantics for NVRAM, VPD, and flash update.

Ensure that an ISP-abort has completed before performing any
update.  After the update do not wait for an ISP-abort completion,
instead just wait until the ISP is reset.  This avoids long
delays due to waiting for loop ready in qla2x00_abort_isp().

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Add Flash-Access-Control support for recent ISPs.

Given the low-level interface varies from one flash-part
manufacturer to the next, the Flash-Access-Control (FAC) mailbox
command makes the specific flash type transparent to the driver
by encapsulating a basic set of accessor and update routines.
Use these new routines where applicable by querying FAC opcode
get-sector-size at init-time.

Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Ensure the timer and DPC routines complete prior to midlayer tear-down.

Since the routines can/will use resources such as devices and
rports that aren't valid after midlayer tear-down, correct this
potential race, by stopping the offending during the early stages
of the remove() callback.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct abort-semantics in qla2x00_abort_all_cmds().

As all commands queued on the physical HBA should be aborted and
returned to the upper-layers.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Update MPI/PHY version retrieval codes.

Reflects layout and format of latest specification.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Preserve an fcport's loop-id after terminate_rport_io().

Since in some circumstances, login-retries may be occuring in the
background via the DPC routine.  This race, in the inadvertant
setting of the loop-id to 'NONE' breaks the existing retry logic.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Pass in optional extended-initialization control block.

Recent ISPs use this data to configure FCF information.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Always (re)read firmware version/capabilities information.

With recent ISPs loading firmware from flash, a flash-update to
the firmware-image region with a follow-on reset will reload the
new image.

Original caching of data only made sense when firmware was bound
with the driver.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Use byte-address while reading FC boot code versions from flash.

The pcihdr variable is used to find valid boot code image to get
FC boot code versions from flash. The pcihdr variable should be
byte aligned.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct over-allocation of firmware-dump buffer.

fce_size should be calculated based on the FCE_SIZE #define.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Initialize FCE debugfs codes with the proper vha structure.

Earlier refactoring codes missed passing the proper vha structure
and instead passed the 'hardware-descriptor' ha.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Consolidate queuecommand implementations.

Post refactoring/multi-queue additions essentially eliminated the
need for separate ISP24XX+ queuecommand as isp_ops contains a
function pointer to the associated 'start_scsi()' operation.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Refactor request/response-queue register handling.

Original code used an overabundance of indirect pointers to
function helpers.  Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Driver version 1.0.5

Bump driver version to 1.0.5.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Improve ADISC timeout handling

The ibmvfc driver currently breaks the CRQ and essentially
resets the entire virtual FC adapter, killing all outstanding
ops to all attached targets, if an ADISC times out during target
discover/rediscovery. This patch adds some code to cancel the
ADISC if it times out, which prevents a single ADISC timeout from
affecting the other devices attached to the fabric.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Show host maxframe_size

Set show_host_maxframe_size so that maxframe_size gets exported in
sysfs for the host.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fixup module parms attributes

The ibmvfc driver really does not handle dynamically changing disc_threads.
To change this dynamically would cause confusion in the driver regarding
the number of event structs allocated. Fix this by simply not allowing
disc_threads to be changed at runtime.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix dropped interrupts

This patch fixes a problem of possible dropped interrupts. Currently,
the ibmvfc driver has a race condition where after ibmvfc_interrupt
gets run, the platform code clears the interrupt. This can result in
lost interrupts and, in worst case scenarios, result in command
timeouts. Fix this by implementing a tasklet similar to what the
ibmvscsi driver does so that interrupt processing is no longer done in
the actual interrupt handler, which eliminates the race.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  Remove two unneeded exports and make two symbols static in fs/mpage.c
  Cleanup after commit 585d3bc06f4ca57f975a5a1f698f65a45ea66225
  Trim includes of fdtable.h
  Don't crap into descriptor table in binfmt_som
  Trim includes in binfmt_elf
  Don't mess with descriptor table in load_elf_binary()
  Get rid of indirect include of fs_struct.h
  New helper - current_umask()
  check_unsafe_exec() doesn't care about signal handlers sharing
  New locking/refcounting for fs_struct
  Take fs_struct handling to new file (fs/fs_struct.c)
  Get rid of bumping fs_struct refcount in pivot_root(2)
  Kill unsharing fs_struct in __set_personality()

Merge branch 'drm-linus' of git://git./linux/kernel/git/airlied/drm-2.6

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (21 commits)
  drm/radeon: load the right microcode on rs780
  drm: remove unused "can_grow" parameter from drm_crtc_helper_initial_config
  drm: fix EDID backward compat check
  drm: sync the mode validation for INTERLACE/DBLSCAN
  drm: fix typo in edid vendor parsing.
  DRM: drm_crtc_helper.h doesn't actually need i2c.h
  drm: fix missing inline function on 32-bit powerpc.
  drm: Use pgprot_writecombine in GEM GTT mapping to get the right bits for !PAT.
  drm/i915: Add a spinlock to protect the active_list
  drm/i915: Fix SDVO TV support
  drm/i915: Fix SDVO CREATE_PREFERRED_INPUT_TIMING command
  drm/i915: Fix error in SDVO DTD and modeline convert
  drm/i915: Fix SDVO command debug function
  drm/i915: fix TV mode setting in property change
  drm/i915: only set TV mode when any property changed
  drm/i915: clean up udelay usage
  drm/i915: add VGA hotplug support for 945+
  drm/i915: correctly set IGD device's gtt size for KMS.
  drm/i915: avoid hanging on to a stale pointer to raw_edid.
  drm/i915: check for -EINVAL from vm_insert_pfn
  ...

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (54 commits)
  glge: remove unused #include <version.h>
  dnet: remove unused #include <version.h>
  tcp: miscounts due to tcp_fragment pcount reset
  tcp: add helper for counter tweaking due mid-wq change
  hso: fix for the 'invalid frame length' messages
  hso: fix for crash when unplugging the device
  fsl_pq_mdio: Fix compile failure
  fsl_pq_mdio: Revive UCC MDIO support
  ucc_geth: Pass proper device to DMA routines, otherwise oops happens
  i.MX31: Fixing cs89x0 network building to i.MX31ADS
  tc35815: Fix build error if NAPI enabled
  hso: add Vendor/Product ID's for new devices
  ucc_geth: Remove unused header
  gianfar: Remove unused header
  kaweth: Fix locking to be SMP-safe
  net: allow multiple dev per napi with GRO
  r8169: reset IntrStatus after chip reset
  ixgbe: Fix potential memory leak/driver panic issue while setting up Tx & Rx ring parameters
  ixgbe: fix ethtool -A|a behavior
  ixgbe: Patch to fix driver panic while freeing up tx & rx resources
  ...

cpumask: fix slab corruption caused by alloc_cpumask_var_node()

Fix slab corruption caused by alloc_cpumask_var_node() overwriting the
tail end of an off-stack cpumask.

The function zeros out cpumask bits beyond the last possible cpu.  The
starting point for zeroing should be the beginning of the mask offset by a
byte count derived from the number of possible cpus.  The offset was
calculated in bits instead of bytes.  This resulted in overwriting the end
of the cpumask.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Mike Travis <travis.sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: <stable@kernel.org> [2.6.29.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ia64: implement interrupt-enabling rwlocks

Implement __raw_read_lock_flags and __raw_write_lock_flags for the ia64
architecture.

[kosaki.motohiro@jp.fujitsu.com: typo fix]
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Allow rwlocks to re-enable interrupts

Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.

Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.

Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Factor out #ifdefs from kernel/spinlock.c to LOCK_CONTENDED_FLAGS

SGI has observed that on large systems, interrupts are not serviced for a
long period of time when waiting for a rwlock.  The following patch series
re-enables irqs while waiting for the lock, resembling the code which is
already there for spinlocks.

I only made the ia64 version, because the patch adds some overhead to the
fast path.  I assume there is currently no demand to have this for other
architectures, because the systems are not so large.  Of course, the
possibility to implement raw_{read|write}_lock_flags for any architecture
is still there.

This patch:

The new macro LOCK_CONTENDED_FLAGS expands to the correct implementation
depending on the config options, so that IRQ's are re-enabled when
possible, but they remain disabled if CONFIG_LOCKDEP is set.

Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/ufs: return f_fsid for statfs(2)

Make ufs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/sysv: return f_fsid for statfs(2)

Make sysv file system return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/squashfs: return f_fsid for statfs(2)

Make squashfs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/reiserfs: return f_fsid for statfs(2)

Make reiserfs3 return f_fsid info for statfs(2).  By Andreas' suggestion,
this patch populates a persistent f_fsid between boots/mounts with help of
on-disk uuid record.

Randy Dunlap reported a compiling error from v2 patch like:
    fs/built-in.o: In function `reiserfs_statfs':
    super.c:(.text+0x7332b): undefined reference to `crc32_le'
    super.c:(.text+0x7333f): undefined reference to `crc32_le'
Also he provided helpful solution to fix this error. The modification of v3
patch is based on Randy's suggestion, add 'select CRC32' in fs/reiserfs/Kconfig.

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/qnx4: return f_fsid for statfs(2)

Make qnx4 file system return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Acked-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/omfs: return f_fsid for statfs(2)

Make omfs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/minix: return f_fsid for statfs(2)

Make minix file system return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/isofs: return f_fsid for statfs(2)

Make isofs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hpfs: return f_fsid for statfs(2)

Make hpfs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfsplus: return f_fsid for statfs(2)

Make hfsplus return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfs: return f_fsid for statfs(2)

Make hfs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/fat: return f_fsid for statfs(2)

Make fat return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/efs: return f_fsid for statfs(2)

Make efs return f_fsid info for statfs(2), and do a little variable
renaming in efs_statfs().

Signed-off-by: Coly Li <coly.li@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/cramfs: return f_fsid for statfs(2)

Make cramfs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/befs: return f_fsid for statfs(2)

Make befs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Sergey S. Kostyliov <rathamahata@php4.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/affs: return f_fsid for statfs(2)

Make affs return f_fsid info for statfs(2).

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/adfs: return f_fsid for statfs(2)

Currently many file systems in Linux kernel do not return f_fsid in statfs
info, the value is set as 0 in vfs layer.  Anyway, in some conditions,
f_fsid from statfs(2) is useful, especially being used as (f_fsid, ino)
pair to uniquely identify a file.

Basic idea of the patches is generating a unique fs ID by
huge_encode_dev(sb->s_bdev->bd_dev) during file system mounting life time
(no endian consistent issue).  sb is a point of struct super_block of
current mounted file system being accessed by statfs(2).

This patch:

Make adfs return f_fsid info for statfs(2), and do a little variable
renaming in adfs_statfs().

Signed-off-by: Coly Li <coly.li@suse.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: "Sergey S. Kostyliov" <rathamahata@php4.ru>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Anders Larsen <al@alarsen.net>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Cc: Jan Kara <jack@suse.cz>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Jamie Lokier <jamie@shareable.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

preadv/pwritev: switch compat readv/preadv/writev/pwritev from fget to fget_light

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

preadv/pwritev: MIPS: Add preadv(2) and pwritev(2) syscalls.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

preadv/pwritev: Add preadv and pwritev system calls.

This patch adds preadv and pwritev system calls.  These syscalls are a
pretty straightforward combination of pread and readv (same for write).
They are quite useful for doing vectored I/O in threaded applications.
Using lseek+readv instead opens race windows you'll have to plug with
locking.

Other systems have such system calls too, for example NetBSD, check
here: http://www.daemon-systems.org/man/preadv.2.html

The application-visible interface provided by glibc should look like
this to be compatible to the existing implementations in the *BSD family:

  ssize_t preadv(int d, const struct iovec *iov, int iovcnt, off_t offset);
  ssize_t pwritev(int d, const struct iovec *iov, int iovcnt, off_t offset);

This prototype has one problem though: On 32bit archs is the (64bit)
offset argument unaligned, which the syscall ABI of several archs doesn't
allow to do.  At least s390 needs a wrapper in glibc to handle this.  As
we'll need a wrappers in glibc anyway I've decided to push problem to
glibc entriely and use a syscall prototype which works without
arch-specific wrappers inside the kernel: The offset argument is
explicitly splitted into two 32bit values.

The patch sports the actual system call implementation and the windup in
the x86 system call tables.  Other archs follow as separate patches.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

preadv/pwritev: create compat_writev()

Factor out some code from compat_sys_writev() which can be shared with the
upcoming compat_sys_pwritev().

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

preadv/pwritev: create compat_readv()

This patch series:

Implement the preadv() and pwritev() syscalls.  *BSD has this syscall for
quite some time.

Test code:

#if 0
set -x
gcc -Wall -O2 -o preadv $0
exit 0
#endif
/*
 * preadv demo / test
 *
 * (c) 2008 Gerd Hoffmann <kraxel@redhat.com>
 *
 * build with "sh $thisfile"
 */

#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <errno.h>
#include <inttypes.h>
#include <sys/uio.h>

/* ----------------------------------------------------------------- */
/* syscall windup                                                    */

#include <sys/syscall.h>
#if 0
/* WARNING: Be sure you know what you are doing if you enable this.
 * linux syscall code isn't upstream yet, syscall numbers are subject
 * to change */
# ifndef __NR_preadv
#  ifdef __i386__
#   define __NR_preadv  333
#   define __NR_pwritev 334
#  endif
#  ifdef __x86_64__
#   define __NR_preadv  295
#   define __NR_pwritev 296
#  endif
# endif
#endif
#ifndef __NR_preadv
# error preadv/pwritev syscall numbers are unknown
#endif

static ssize_t preadv(int fd, const struct iovec *iov, int iovcnt, off_t offset)
{
    uint32_t pos_high = (offset >> 32) & 0xffffffff;
    uint32_t pos_low  =  offset        & 0xffffffff;

    return syscall(__NR_preadv, fd, iov, iovcnt, pos_high, pos_low);
}

static ssize_t pwritev(int fd, const struct iovec *iov, int iovcnt, off_t offset)
{
    uint32_t pos_high = (offset >> 32) & 0xffffffff;
    uint32_t pos_low  =  offset        & 0xffffffff;

    return syscall(__NR_pwritev, fd, iov, iovcnt, pos_high, pos_low);
}

/* ----------------------------------------------------------------- */
/* demo/test app                                                     */

static char filename[] = "/tmp/preadv-XXXXXX";
static char outbuf[11] = "0123456789";
static char inbuf[11]  = "----------";

static struct iovec ovec[2] = {{
        .iov_base = outbuf + 5,
        .iov_len  = 5,
    },{
        .iov_base = outbuf + 0,
        .iov_len  = 5,
    }};

static struct iovec ivec[3] = {{
        .iov_base = inbuf + 6,
        .iov_len  = 2,
    },{
        .iov_base = inbuf + 4,
        .iov_len  = 2,
    },{
        .iov_base = inbuf + 2,
        .iov_len  = 2,
    }};

void cleanup(void)
{
    unlink(filename);
}

int main(int argc, char **argv)
{
    int fd, rc;

    fd = mkstemp(filename);
    if (-1 == fd) {
        perror("mkstemp");
        exit(1);
    }
    atexit(cleanup);

    /* write to file: "56789-01234" */
    rc = pwritev(fd, ovec, 2, 0);
    if (rc < 0) {
        perror("pwritev");
        exit(1);
    }

    /* read from file: "78-90-12" */
    rc = preadv(fd, ivec, 3, 2);
    if (rc < 0) {
        perror("preadv");
        exit(1);
    }

    printf("result  : %s\n", inbuf);
    printf("expected: %s\n", "--129078--");
    exit(0);
}

This patch:

Factor out some code from compat_sys_readv() which can be shared with the
upcoming compat_sys_preadv().

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cramfs: propagate uncompression errors

Decompression errors can arise due to corruption of compressed blocks on
flash or in memory.  This patch propagates errors detected during
decompression back to the block layer.

Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

xpc_sn2: fix max() warning about pointers of different types

Fix a minor compile warning when building on ia64.

drivers/misc/sgi-xp/xpc_sn2.c: In function `xpc_clear_remote_msgqueue_flags_sn2':
drivers/misc/sgi-xp/xpc_sn2.c:1746: warning: comparison of distinct pointer types lacks a cast

Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: remove SGI_GRU as a valid config option for ia64 configs with SGI_UV

Some current configs turn on GRU for ia64.  The GRU code does not
correctly load on boot on ia64 (GRU does continue to work for x86-64), so
changing the IA64 Kconfig to not select GRU on ia64 configs for now until
we have time to fix.

Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: support multiple pagesizes in GRU

Add multiple pagesize support to the GRU driver.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: fix bugs related to module unload of the GRU driver

Fix bugs related to module unload of the GRU driver.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: macro for scanning all gru chiplets

Add macro for scanning all active GRU chiplets.  Maximum chiplet id is
saved during GRU initialization.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: add support to the GRU driver for message queue interrupts

Add support to the GRU driver for message queue interrupts.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: restructure the GRU vtop functions

Restructure the GRU vtop functions in preparation for future changes.
This patch simply moves code around & does not change the algorithm.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: aSID (context management) bug fixes

This patch fixes bugs related to ASID (context id) management in the GRU
driver.  These changes are all internal to the SGI GRU driver and have no
effect on the base kernel.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: add support for a user to explicitly unload a GRU context

Add support for a user to explicitly unload a GRU context.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: add statistics to the GRU context management functions

Add statistics to the GRU context management functions.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: change GRU CCH commands from inline functions to outofline functions

Change the GRU instructions that manage contexts from inline functions to
out-of-line functions.  This simplifies adding statistics & error checking
to these functions.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: improvements to GRU debug messages & statistics

Improvements to GRU debug messages & statistics.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: misc GRU cleanup

Misc trivial GRU drivers fixes:
- fix long lines
- eliminate extra whitespace
- eliminate compiler warning
- better validation of invalidate user parameters
- bug fix for GRU TLB flush (not the cpu TLB flush)

These changes are all internal to the SGI GRU driver and have no effect
on the base kernel.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: add macros for using the UV hub to send interrupts

Add macros for using the UV hub to send interrupts.  Change the IPI code
to use these macros.  These macros will also be used in additional patches
that will follow.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: add definitions of ia64 GRU MMRs

Add definitions for IA64 GRU MMRs.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: add definitions of x86_64 GRU MMRs

Add definitions for x86_64 GRU MMRs.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sgi-gru: exclude UV definitions on 32-bit x86

Eliminate compile errors on 32-bit X86 caused by UV.

Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

relay: fix for possible loss/corruption of produced subbufs

Fix possible loss/corruption of produced subbufs in
relay_subbufs_consumed().

When buf->subbufs_produced wraps around after UINT_MAX and
buf->subbufs_consumed is still < UINT_MAX, the condition

if (buf->subbufs_consumed > buf->subbufs_produced)

will be true even for certain valid values of subbufs_consumed.  This may
lead to loss or corruption of produced subbufs.

Signed-off-by: Aravind Srinivasan <raa.aars@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kexec: vmcoreinfo_data[] can become static

The vmcoreinfo_data[] array is not used outside of kernel/kexec.c, and
can therefore become static. This patch adds the relevant keyword to the
definition of the array.

Noticed by sparse.

Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kexec: add dmesg log symbols to /proc/vmcoreinfo lists

It would be nice to be able to extract the dmesg log from a vmcore file
without needing to keep the debug symbols for the running kernel handy all
the time.  We have a facility to do this in /proc/vmcore.  This patch adds
the log_buf and log_end symbols to the vmcoreinfo area so that tools (like
makedumpfile) can easily extract the dmesg logs from a vmcore image.

[akpm@linux-foundation.org: several fixes and cleanups]
[akpm@linux-foundation.org: fix unused log_buf_kexec_setup()]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Simon Horman <horms@verge.net.au>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

w1: coding style cleanups in w1_io.c

This fixes a number of coding style issues I stubled over.

Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

parport: netmos 9845 & 9855 1P4S fixes

netmos serial/parallel adapters come in different flavour differing only
by the number of parallel and serial ports, which are encoded in the
subdevice ID.

Last fix of Christian Pellegrin for 9855 2P2S broke support for 9855 1P4S,
and works only by side-effect for the first parallel port of a 2P2S, as
this first parallel port is found by reading the second addr entry of
(struct parport_pc_pci) cards[netmos_9855], which is not initialized, and
hence has value 0, which happens to be the BAR of the first parallel port.

netmos_9xx5_combo entry in (struct parport_pc_pci) cards[], which is used
for a 9845 1P4S must also be fixed for the parallel port support when
there are 4 serial ports because this entry currently gives 2 as BAR index
for the parallel port.  Actually, in this case, BAR 2 is the 3rd serial
port while the parallel port is at BAR 4.

I fixed 9845 1P4S and 9855 1P4S support, while preserving 9855 2P2S support,

- by creating a netmos_9855_2p entry and using it for 9855 boards with 2
  parallel ports : 9855 2P2S and 9855 2P0S boards,

- and by allowing netmos_parallel_init to change not only the number of
  parallel ports (0 or 1), but making it also change the BAR index of the
  parallel port when the serial ports are before the parallel port.

PS: the netmos_9855_2p entry in (struct pciserial_board)
pci_parport_serial_boards[] is needed because netmos_parallel_init has no
clean way to replace FL_BASE2 by FL_BASE4 in the description of the serial
ports in function of the number of parallel ports on the card.

Tested with 9845 1P4S, 9855 1P4S and 9855 2P2S boards.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: AMD8111 driver Kconfig & Makefile

Introduce Kconfig and Makefile options for AMD8111 EDAC driver.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: AMD8131 driver Kconfig & Makefile

Introduce Kconfig and Makefile options for AMD8131 EDAC driver.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: AMD8131 driver source file

Introduce AMD8131 EDAC driver source file, which makes use of error
detections on the PCI-X Bridge Controllers on the AMD8131 HyperTransport
PCI-X Tunnel.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: AMD8131 driver header file

Introduce AMD8131 EDAC driver header file, which adds register and bits
definitions for the PCI-X Bridge Controller on the AMD8131 HyperTransport
I/O Hub.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pci: Add AMD8111 PCI Bridge PCI Device ID

Add the PCI Device ID of the PCI Bridge Controller on AMD8111 chip.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: Add edac_pci_alloc_index()

Add edac_pci_alloc_index(), because for MAPLE platform there may exist
several EDAC driver modules that could make use of edac_pci_ctl_info
structure at the same time.  The index allocation for these structures
should be taken care of by EDAC core.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: AMD8111 driver source file

Introduce AMD8111 EDAC driver source file, which makes use of error
detections on the LPC Bridge Controller and PCI Bridge Controller on the
AMD8111 HyperTransport I/O Hub.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: AMD8111 driver header file

Introduce AMD8111 EDAC driver header file, which adds register and bits
definitions for the LPC Bridge Controller and PCI Bridge Controller on the
AMD8111 HyperTransport I/O Hub.

Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: new ppc4xx driver module

This adds support for an EDAC memory controller adaptation driver for the
"ibm,sdram-4xx-ddr2" ECC controller realized in the AMCC PowerPC 405EX[r].

At present, this driver has been developed and tested against the
controller realization in the AMCC PPC405EX[r] on the AMCC Kilauea and
Haleakala boards (256 MiB w/o ECC memory soldered onto the board) and a
proprietary board based on those designs (128 MiB ECC memory, also
soldered onto the board).

In the future, dynamic feature detection and handling needs to be added
for the other realizations of this controller found in the 440SP, 440SPe,
460EX, 460GT and 460SX.

Eventually, this driver will likely be evolved and adapted to the above
variant realizations of this controller as well as broken apart to handle
the other known ECC-capable controllers prevalent in other PPC4xx
processors:

  - IBM SDRAM (405GP, 405CR and 405EP) "ibm,sdram-4xx"
  - IBM DDR1 (440GP, 440GX, 440EP and 440GR) "ibm,sdram-4xx-ddr"
  - Denali DDR1/DDR2 (440EPX and 440GRX) "denali,sdram-4xx-ddr2"

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: remove EDAC's experimental status

After 3 years, this is a patch to remove the EXPERIMENTAL tag on EDAC.  We
now have many module drivers submitters in EDAC and believe EDAC is no
longer EXPERIMENTAL

Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

edac: add more verbose debug info

A patch for making a debugging information more verbose for use in
development debugging.

By enabling the new option "More verbose debugging", information about
source file and line number will be added to debugging message.

This is sample output,

EDAC MC0: Giving out device to 'e7xxx_edac' 'E7205': DEV 0000:00:00.0
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 48: edac_pci_alloc_ctl_info()
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 334: edac_pci_add_device()
           ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nbd: trivial cleanups

Trivial cleanups for nbd: only the return -EIO one really changes code,
and I've verified all the callers (plus 0 == success, 1 == error
convention is really ugly).

Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nbd: add locking to nbd_ioctl

The code was written to rely on big kernel lock to protect it from races.
It mostly works when interface is not abused.

So this uses tx_lock to protect data structures from concurrent use
between ioctl and worker threads.

Next step will be moving from ioctl to unlocked_ioctl.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: add missing return]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pids: kill signal_struct-> __pgrp/__session and friends

We are wasting 2 words in signal_struct without any reason to implement
task_pgrp_nr() and task_session_nr().

task_session_nr() has no callers since
2e2ba22ea4fd4bb85f0fa37c521066db6775cbef, we can remove it.

task_pgrp_nr() is still (I believe wrongly) used in fs/autofsX and
fs/coda.

This patch reimplements task_pgrp_nr() via task_pgrp_nr_ns(), and kills
__pgrp/__session and the related helpers.

The change in drivers/char/tty_io.c is cosmetic, but hopefully makes sense
anyway.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Alan Cox <number6@the-village.bc.nu> [tty parts]
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pids: refactor vnr/nr_ns helpers to make them safe

Inho, the safety rules for vnr/nr_ns helpers are horrible and buggy.

task_pid_nr_ns(task) needs rcu/tasklist depending on task == current.

As for "special" pids, vnr/nr_ns helpers always need rcu.  However, if
task != current, they are unsafe even under rcu lock, we can't trust
task->group_leader without the special checks.

And almost every helper has a callsite which needs a fix.

Also, it is a bit annoying that the implementations of, say,
task_pgrp_vnr() and task_pgrp_nr_ns() are not "symmetrical".

This patch introduces the new helper, __task_pid_nr_ns(), which is always
safe to use, and turns all other helpers into the trivial wrappers.

After this I'll send another patch which converts task_tgid_xxx() as well,
they're are a bit special.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pids: improve get_task_pid() to fix the unsafe sys_wait4()->task_pgrp()

sys_wait4() does get_pid(task_pgrp(current)), this is not safe.  We can
add rcu lock/unlock around, but we already have get_task_pid() which can
be improved to handle the special pids in more reliable manner.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pids: document task_pgrp/task_session is not safe without tasklist/rcu

Even if task == current, it is not safe to dereference the result of
task_pgrp/task_session.  We can race with another thread which changes the
special pid via setpgid/setsid.

Document this.  The next 2 patches give an example of the unsafe usage, we
have more bad users.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysctl: fix suid_dumpable and lease-break-time sysctls

Arne de Bruijn points out that commit
76fdbb25f963de5dc1e308325f0578a2f92b1c2d ("coredump masking: bound
suid_dumpable sysctl") mistakenly limits lease-break-time instead of
suid_dumpable.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Reported-by: Arne de Bruijn <kernelbt@arbruijn.dds.nl>
Cc: Kawai, Hidehiro <hidehiro.kawai.ez@hitachi.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hpet: fix the possibility of insane return value of hpet_calibrate() against SMI

hpet_calibrate() has a possibility of miss-calibration due to SMI.  If SMI
interrupts in the while loop of calibration, then return value will be
big.  This change calibrates until stabilizing by the return value with a
small value.

[akpm@linux-foundation.org: trivial style tweaks]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Cc: Robert Picco <Robert.Picco@hp.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

synclink_gt: add clock options

Add support for x8 asynchronous sample rate and ability to specify base
clock frequency.

Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

struct linux_binprm: drop unused fields

Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bin_elf_fdpic: check the return value of clear_user

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>