Dave Chinner [Mon, 22 Jun 2015 22:49:01 +0000 (08:49 +1000)]
Merge branch 'xfs-misc-fixes-for-4.2-3' into for-next
Dave Chinner [Mon, 22 Jun 2015 22:48:43 +0000 (08:48 +1000)]
Merge branch 'xfs-freelist-cleanup' into for-next
Brian Foster [Mon, 22 Jun 2015 22:47:20 +0000 (08:47 +1000)]
xfs: don't truncate attribute extents if no extents exist
The xfs_attr3_root_inactive() call from xfs_attr_inactive() assumes that
attribute blocks exist to invalidate. It is possible to have an
attribute fork without extents, however. Consider the case where the
attribute fork is created towards the beginning of xfs_attr_set() but
some part of the subsequent attribute set fails.
If an inode in such a state hits xfs_attr_inactive(), it eventually
calls xfs_dabuf_map() and possibly xfs_bmapi_read(). The former emits a
filesystem corruption warning, returns an error that bubbles back up to
xfs_attr_inactive(), and leads to destruction of the in-core attribute
fork without an on-disk reset. If the inode happens to make it back
through xfs_inactive() in this state (e.g., via a concurrent bulkstat
that cycles the inode from the reclaim state and releases it), i_afp
might not exist when xfs_bmapi_read() is called and causes a NULL
dereference panic.
A '-p 2' fsstress run to ENOSPC on a relatively small fs (1GB)
reproduces these problems. The behavior is a regression caused by:
6dfe5a0 xfs: xfs_attr_inactive leaves inconsistent attr fork state behind
... which removed logic that avoided the attribute extent truncate when
no extents exist. Restore this logic to ensure the attribute fork is
destroyed and reset correctly if it exists without any allocated
extents.
cc: stable@vger.kernel.org # 3.12 to 4.0.x
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Mon, 22 Jun 2015 00:13:30 +0000 (10:13 +1000)]
xfs: clean up XFS_MIN_FREELIST macros
We no longer calculate the minimum freelist size from the on-disk
AGF, so we don't need the macros used for this. That means the
nested macros can be cleaned up, and turn this into an actual
function so the logic is clear and concise. This will make it much
easier to add support for the rmap btree when the time comes.
This also gets rid of the XFS_AG_MAXLEVELS macro used by these
freelist macros as it is simply a wrapper around a single variable.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Mon, 22 Jun 2015 00:13:19 +0000 (10:13 +1000)]
xfs: sanitise error handling in xfs_alloc_fix_freelist
The error handling is currently an inconsistent mess as every error
condition handles return values and releasing buffers individually.
Clean this up by using gotos and a sane error label stack.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Mon, 22 Jun 2015 00:04:42 +0000 (10:04 +1000)]
xfs: factor out free space extent length check
The longest extent length checks in xfs_alloc_fix_freelist() are now
essentially identical. Factor them out into a helper function, so we
know they are checking exactly the same thing before and after we
lock the AGF.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Mon, 22 Jun 2015 00:04:31 +0000 (10:04 +1000)]
xfs: xfs_alloc_fix_freelist() can use incore perag structures
At the moment, xfs_alloc_fix_freelist() uses a mix of per-ag based
access and agf buffer based access to freelist and space usage
information. However, once the AGF buffer is locked inside this
function, it is guaranteed that both the in-memory and on-disk
values are identical. xfs_alloc_fix_freelist() doesn't modify the
values in the structures directly, so it is a read-only user of the
infomration, and hence can use the per-ag structure exclusively for
determining what it should do.
This opens up an avenue for cleaning up a lot of duplicated logic
whose only difference is the structure it gets the data from, and in
doing so removes a lot of needless byte swapping overhead when
fixing up the free list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Sun, 21 Jun 2015 23:45:10 +0000 (09:45 +1000)]
xfs: remove xfs_caddr_t
Just use char pointers directly instead of the confusing typedef to a
pointer type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Sun, 21 Jun 2015 23:44:47 +0000 (09:44 +1000)]
xfs: use void pointers in log validation helpers
Compared to char pointers this saves us a lot of casting effort. Also
add another local variable to make the code easier to read.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Sun, 21 Jun 2015 23:44:29 +0000 (09:44 +1000)]
xfs: return a void pointer from xfs_buf_offset
This avoids all kinds of unessecary casts in an envrionment like Linux where
we can assume that pointer arithmetics are support on void pointers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Sun, 21 Jun 2015 23:44:02 +0000 (09:44 +1000)]
xfs: remove inst_t
We can simply use a void pointer to pass a long return addresses in the
debugging helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Sun, 21 Jun 2015 23:43:32 +0000 (09:43 +1000)]
xfs: remove __psint_t and __psunsigned_t
Replace uses of __psint_t with the proper uintptr_t and ptrdiff_t types,
and remove the defintions of __psint_t and __psunsigned_t.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Eric Sandeen [Sun, 21 Jun 2015 23:42:48 +0000 (09:42 +1000)]
xfs: fix remote symlinks on V5/CRC filesystems
If we create a CRC filesystem, mount it, and create a symlink with
a path long enough that it can't live in the inode, we get a very
strange result upon remount:
# ls -l mnt
total 4
lrwxrwxrwx. 1 root root 929 Jun 15 16:58 link -> XSLM
XSLM is the V5 symlink block header magic (which happens to be
followed by a NUL, so the string looks terminated).
xfs_readlink_bmap() advanced cur_chunk by the size of the header
for CRC filesystems, but never actually used that pointer; it
kept reading from bp->b_addr, which is the start of the block,
rather than the start of the symlink data after the header.
Looks like this problem goes back to v3.10.
Fixing this gets us reading the proper link target, again.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 4 Jun 2015 03:55:48 +0000 (13:55 +1000)]
Merge branch 'xfs-commit-cleanup' into for-next
Conflicts:
fs/xfs/xfs_attr_inactive.c
Christoph Hellwig [Thu, 4 Jun 2015 03:48:20 +0000 (13:48 +1000)]
xfs: fix xfs_log_done interface
Instead of the confusing flags argument pass a boolean flag to indicate if
we want to release or regrant a log reservation.
Also ensure that xfs_log_done always drop the reference on the log ticket,
to both simplify the code and make the logic in xfs_trans_roll easier
to understand.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Thu, 4 Jun 2015 03:48:08 +0000 (13:48 +1000)]
xfs: saner xfs_trans_commit interface
The flags argument to xfs_trans_commit is not useful for most callers, as
a commit of a transaction without a permanent log reservation must pass
0 here, and all callers for a transaction with a permanent log reservation
except for xfs_trans_roll must pass XFS_TRANS_RELEASE_LOG_RES. So remove
the flags argument from the public xfs_trans_commit interfaces, and
introduce low-level __xfs_trans_commit variant just for xfs_trans_roll
that regrants a log reservation instead of releasing it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Thu, 4 Jun 2015 03:47:56 +0000 (13:47 +1000)]
xfs: remove the flags argument to xfs_trans_cancel
xfs_trans_cancel takes two flags arguments: XFS_TRANS_RELEASE_LOG_RES and
XFS_TRANS_ABORT. Both of them are a direct product of the transaction
state, and can be deducted:
- any dirty transaction needs XFS_TRANS_ABORT to be properly canceled,
and XFS_TRANS_ABORT is a noop for a transaction that is not dirty.
- any transaction with a permanent log reservation needs
XFS_TRANS_RELEASE_LOG_RES to be properly canceled, and passing
XFS_TRANS_RELEASE_LOG_RES for a transaction without a permanent
log reservation is invalid.
So just remove the flags argument and do the right thing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Thu, 4 Jun 2015 03:47:43 +0000 (13:47 +1000)]
xfs: pass a boolean flag to xfs_trans_free_items
The flags value always was 0 or XFS_TRANS_ABORT. Switch to a bool
parameter to allow further cleanups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Christoph Hellwig [Thu, 4 Jun 2015 03:47:29 +0000 (13:47 +1000)]
xfs: switch remaining xfs_trans_dup users to xfs_trans_roll
We have three remaining callers of xfs_trans_dup:
- xfs_itruncate_extents which open codes xfs_trans_roll
- xfs_bmap_finish doesn't have an xfs_inode argument and thus leaves
attaching them to it's callers, but otherwise is identical to
xfs_trans_roll
- xfs_dir_ialloc looks at the log reservations in the old xfs_trans
structure instead of the log reservation parameters, but otherwise
is identical to xfs_trans_roll.
By allowing a NULL xfs_inode argument to xfs_trans_roll we can switch
these three remaining users over to xfs_trans_roll and mark xfs_trans_dup
static.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 4 Jun 2015 03:31:13 +0000 (13:31 +1000)]
Merge branch 'xfs-misc-fixes-for-4.2-2' into for-next
Brian Foster [Thu, 4 Jun 2015 03:03:34 +0000 (13:03 +1000)]
xfs: check min blks for random debug mode sparse allocations
The inode allocator enables random sparse inode chunk allocations in
DEBUG mode to facilitate testing. Sparse inode allocations are not
always possible, however, depending on the fs geometry. For example,
there is no possibility for a sparse inode allocation on filesystems
where the block size is large enough to fit one or more inode chunks
within a single block.
Fix up the DEBUG mode sparse inode allocation logic to trigger random
sparse allocations only when the geometry of the fs allows it.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 4 Jun 2015 03:03:34 +0000 (13:03 +1000)]
xfs: fix sparse inodes 32-bit compile failure
The kbuild test robot reports the following compilation failure with a
32-bit kernel configuration:
fs/built-in.o: In function `xfs_ifree_cluster':
>> xfs_inode.c:(.text+0x17ac84): undefined reference to `__umoddi3'
This is due to the use of the modulus operator on a 64-bit variable in
the ASSERT() added as part of the following commit:
xfs: skip unallocated regions of inode chunks in xfs_ifree_cluster()
This ASSERT() simply checks that the offset of the inode in a sparse
cluster is appropriately aligned. Since the maximum inode record offset
is 63 (for a 64 inode record) and the calculated offset here should be
something less than that, just use a 32-bit variable to store the offset
and call the do_mod() helper.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 4 Jun 2015 03:01:49 +0000 (13:01 +1000)]
Merge branch 'xfs-dax-support' into for-next
Dave Chinner [Wed, 3 Jun 2015 23:19:18 +0000 (09:19 +1000)]
xfs: add initial DAX support
Add initial DAX support to XFS. To do this we need a new mount
option to turn DAX on filesystem, and we need to propagate this into
the inode flags whenever an inode is instantiated so that the
per-inode checks throughout the code Do The Right Thing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:19:15 +0000 (09:19 +1000)]
xfs: add DAX IO path support
DAX does not do buffered IO (can't buffer direct access!) and hence
all read/write IO is vectored through the direct IO path. Hence we
need to add the DAX IO path callouts to the direct IO
infrastructure.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:19:10 +0000 (09:19 +1000)]
xfs: add DAX truncate support
When we truncate a DAX file, we need to call through the DAX page
truncation path rather than through block_truncate_page() so that
mappings and block zeroing are all handled correctly. Otherwise,
truncate does not need to change.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:19:08 +0000 (09:19 +1000)]
xfs: add DAX block zeroing support
Add initial support for DAX block zeroing operations to XFS. DAX
cannot use buffered IO through the page cache for zeroing, nor do we
need to issue IO for uncached block zeroing. In both cases, we can
simply call out to the dax block zeroing function.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:18:53 +0000 (09:18 +1000)]
xfs: add DAX file operations support
Add the initial support for DAX file operations to XFS. This
includes the necessary block allocation and mmap page fault hooks
for DAX to function.
Note that there are changes to the splice interfaces to ensure that
for DAX splice avoids direct page cache manipulations and instead
takes the DAX IO paths for read/write operations.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:18:18 +0000 (09:18 +1000)]
dax: expose __dax_fault for filesystems with locking constraints
Some filesystems cannot call dax_fault() directly because they have
different locking and/or allocation constraints in the page fault IO
path. To handle this, we need to follow the same model as the
generic block_page_mkwrite code, where the internals are exposed via
__block_page_mkwrite() so that filesystems can wrap the correct
locking and operations around the outside.
This is loosely based on a patch originally from Matthew Willcox.
Unlike the original patch, it does not change ext4 code, error
returns or unwritten extent conversion handling. It also adds a
__dax_mkwrite() wrapper for .page_mkwrite implementations to do the
right thing, too.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:18:18 +0000 (09:18 +1000)]
dax: don't abuse get_block mapping for endio callbacks
dax_fault() currently relies on the get_block callback to attach an
io completion callback to the mapping buffer head so that it can
run unwritten extent conversion after zeroing allocated blocks.
Instead of this hack, pass the conversion callback directly into
dax_fault() similar to the get_block callback. When the filesystem
allocates unwritten extents, it will set the buffer_unwritten()
flag, and hence the dax_fault code can call the completion function
in the contexts where it is necessary without overloading the
mapping buffer head.
Note: The changes to ext4 to use this interface are suspect at best.
In fact, the way ext4 did this end_io assignment in the first place
looks suspect because it only set a completion callback when there
wasn't already some other write() call taking place on the same
inode. The ext4 end_io code looks rather intricate and fragile with
all it's reference counting and passing to different contexts for
modification via inode private pointers that aren't protected by
locks...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 3 Jun 2015 23:18:18 +0000 (09:18 +1000)]
xfs: mmap lock needs to be inside freeze protection
Lock ordering for the new mmap lock needs to be:
mmap_sem
sb_start_pagefault
i_mmap_lock
page lock
<fault processsing>
Right now xfs_vm_page_mkwrite gets this the wrong way around,
While technically it cannot deadlock due to the current freeze
ordering, it's still a landmine that might explode if we change
anything in future. Hence we need to nest the locks correctly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Mon, 1 Jun 2015 00:51:38 +0000 (10:51 +1000)]
Merge branch 'xfs-sparse-inode' into for-next
Dave Chinner [Mon, 1 Jun 2015 00:50:18 +0000 (10:50 +1000)]
Merge branch 'xfs-misc-fixes-for-4.2' into for-next
Nan Jia [Mon, 1 Jun 2015 00:50:00 +0000 (10:50 +1000)]
xfs: Clean up xfs_trans_dup_dqinfo
Fixed two missing spaces.
Signed-off-by: Nan Jia <jiananmail@gmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Fanael Linithien [Sun, 31 May 2015 21:15:38 +0000 (07:15 +1000)]
xfs: fix kernel version in docs
Linux v3.20 was released as v4.0.
Signed-off-by: Fanael Linithien <fanael4@gmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Eric Sandeen [Sun, 31 May 2015 21:15:38 +0000 (07:15 +1000)]
xfs: don't cast string literals
The commit:
a9273ca5 xfs: convert attr to use unsigned names
added these (unsigned char *) casts, but then the _SIZE macros
return "7" - size of a pointer minus one - not the length of
the string. This is harmless in the kernel, because the _SIZE
macros are not used, but as we sync up with userspace, this will
matter.
I don't think the cast is necessary; i.e. assigning the string
literal to an unsigned char *, or passing it to a function
expecting an unsigned char *, should be ok, right?
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Sun, 31 May 2015 21:15:37 +0000 (07:15 +1000)]
xfs: fix quota block reservation leak when tp allocates and frees blocks
Al Viro reports that generic/231 fails frequently on XFS and bisected
the problem to the following commit:
5d11fb4b xfs: rework zero range to prevent invalid i_size updates
... which is just the first commit that happens to cause fsx to
reproduce the problem. fsx reproduces via zero range calls. The
aforementioned commit overhauls zero range to use hole punch and
fallocate. As it turns out, the problem is reproducible on demand using
basic hole punch as follows:
$ mkfs.xfs -f -m crc=1,finobt=1 <dev>
$ mount <dev> /mnt -o uquota
$ xfs_io -f -c "falloc 0 50m" /mnt/file
$ for i in $(seq 1 20); do xfs_io -c "fpunch ${i}m 32k" /mnt/file; done
$ rm -f /mnt/file
$ repquota -us /mnt
...
User used soft hard grace used soft hard grace
----------------------------------------------------------------------
root -- 32K 0K 0K 3 0 0
A file is allocated with a single 50m extent. The extent count increases
via hole punches until the bmap converts to btree format. The file is
removed but quota reports 32k of space usage for the user. This
reservation is effectively leaked for the lifetime of the mount.
The reason this occurs is because the quota block reservation tracking
is confused when a transaction happens to free and allocate blocks at
the same time. Consider the following sequence of events:
- tp is allocated from xfs_free_file_space() and reserves several blocks
for btree management. Blocks are reserved against the dquot and marked
as such in the transaction (qtrx->qt_blk_res).
- 8 blocks are accounted free when the 32k range is punched out.
xfs_trans_mod_dquot() is called with XFS_TRANS_DQ_BCOUNT and sets
->qt_bcount_delta to -8.
- Subsequently, a block is allocated against the same transaction by
xfs_bmap_extents_to_btree() for btree conversion. A call to
xfs_trans_mod_dquot() increases qt_blk_res_used to 1 and qt_bcount_delta
to -7.
- The transaction is dup'd and committed by xfs_bmap_finish().
xfs_trans_dup_dqinfo() sets the first transaction up such that it has a
matching qt_blk_res and qt_blk_res_used of 1. The remaining unused
reservation is transferred to the duplicate tp.
When the transactions are committed, the dquots are fixed up in
xfs_trans_apply_dquot_deltas() according to one of two methods:
1.) If the transaction holds a block reservation (->qt_blk_res != 0),
_only_ the unused portion reservation is unaccounted from the dquot.
Note that the tp duplication behavior of xfs_bmap_finish() makes it such
that qt_blk_res is typically 0 for tp's with unused reservation.
2.) Otherwise, the dquot is fixed up based on the block delta
(->qt_bcount_delta) created by the transaction.
Therefore, if a transaction has a negative qt_bcount_delta and positive
qt_blk_res_used, the former set of blocks that have been removed from
the file are never factored out of the in-core dquot reservation.
Instead, *_apply_dquot_deltas() sees 1 block used out of a 1 block
reservation and believes there is nothing to fix up. The on-disk
d_bcount is updated independently from qt_bcount_delta, and thus is
correct (and allows the quota usage to correct on remount).
To deal with this situation, we effectively want the "used reservation"
part of the transaction to be consistent with any freed blocks with
respect to quota tracking. For example, if 8 blocks are freed, the
subsequent single block allocation does not need to consume the initial
reservation made by the tp. Instead, it simply borrows one from the
previously freed. One possible implementation of such borrowing is to
avoid the blks_res_used increment when bcount_delta is negative. This
alone is flawed logic in that it only handles the case where blocks are
freed before allocated, however.
Rather than add more complexity to manage synchronization between
bcount_delta and blks_res_used, kill the latter entirely. blk_res_used
is only updated in one place and always in sync with delta_bcount.
Therefore, the net block reservation consumption of the transaction is
always available from bcount_delta. Calculate the reservation
consumption on the fly where necessary based on whether the tp has a
reservation and results in a positive net block delta on the inode.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Sun, 31 May 2015 21:15:23 +0000 (07:15 +1000)]
xfs: always log the inode on unwritten extent conversion
The fsync() requirements for crash consistency on XFS are to flush file
data and force any in-core inode updates to the log. We currently check
whether the inode is pinned to identify whether the log needs to be
forced, since a non-zero pin count generally represents an inode that
has transactions awaiting a flush to the on-disk log.
This is not sufficient in all cases, however. Reports of xfstests test
generic/311 failures on ppc64/s390x hosts have identified failures to
fsync outstanding inode modifications due to the inode not being pinned
at the time of the fsync. This occurs because certain bmap updates can
complete by logging bmapbt buffers but without ever dirtying (and thus
pinning) the core inode. The following is a specific incarnation of this
problem:
$ mount $dev /mnt -o noatime,nobarrier
$ for i in $(seq 0 2 31); do \
xfs_io -f -c "falloc $((i * 32768)) 32k" -c fsync /mnt/file; \
done
$ xfs_io -c "pwrite -S 0 80k 16k" -c fsync -c "pwrite 76k 4k" -c fsync /mnt/file; \
hexdump /mnt/file; \
./xfstests-dev/src/godown /mnt
...
0000000 0000 0000 0000 0000 0000 0000 0000 0000
*
0013000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
*
0014000 0000 0000 0000 0000 0000 0000 0000 0000
*
00f8000
$ umount /mnt; mount ...
$ hexdump /mnt/file
0000000 0000 0000 0000 0000 0000 0000 0000 0000
*
00f8000
In short, the unwritten extent conversion for the last write is lost
despite the fact that an fsync executed before the filesystem was
shutdown. Note that this is impossible to reproduce on v5 supers due to
unconditional time callbacks for di_changecount and highly difficult to
reproduce on CONFIG_HZ=1000 kernels due to those same callbacks
frequently updating cmtime prior to the bmap update. CONFIG_HZ=100
reduces timer granularity enough to increase the odds that time updates
are skipped and allows this to reproduce within a handful of attempts.
To deal with this problem, unconditionally log the core in the unwritten
extent conversion path. Fix up logflags after the extent conversion to
keep the extent update code consistent with the other extent update
helpers. This fixup is not necessary for the other (hole, delay) extent
helpers because they execute in the block allocation codepath, which
already logs the inode for other reasons (e.g., for di_nblocks).
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:26:33 +0000 (09:26 +1000)]
xfs: enable sparse inode chunks for v5 superblocks
Enable mounting of filesystems with sparse inode support enabled. Add
the incompat. feature bit to the *_ALL mask.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:26:03 +0000 (09:26 +1000)]
xfs: skip unallocated regions of inode chunks in xfs_ifree_cluster()
xfs_ifree_cluster() is called to mark all in-memory inodes and inode
buffers as stale. This occurs after we've removed the inobt records and
dropped any references of inobt data. xfs_ifree_cluster() uses the
starting inode number to walk the namespace of inodes expected for a
single chunk a cluster buffer at a time. The cluster buffer disk
addresses are calculated by decoding the sequential inode numbers
expected from the chunk.
The problem with this approach is that if the inode chunk being removed
is a sparse chunk, not all of the buffer addresses that are calculated
as part of this sequence may be inode clusters. Attempting to acquire
the buffer based on expected inode characterstics (i.e., cluster length)
can lead to errors and is generally incorrect.
We already use a couple variables to carry requisite state from
xfs_difree() to xfs_ifree_cluster(). Rather than add a third, define a
new internal structure to carry the existing parameters through these
functions. Add an alloc field that represents the physical allocation
bitmap of inodes in the chunk being removed. Modify xfs_ifree_cluster()
to check each inode against the bitmap and skip the clusters that were
never allocated as real inodes on disk.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:22:52 +0000 (09:22 +1000)]
xfs: only free allocated regions of inode chunks
An inode chunk is currently added to the transaction free list based on
a simple fsb conversion and hardcoded chunk length. The nature of sparse
chunks is such that the physical chunk of inodes on disk may consist of
one or more discontiguous parts. Blocks that reside in the holes of the
inode chunk are not inodes and could be allocated to any other use or
not allocated at all.
Refactor the existing xfs_bmap_add_free() call into the
xfs_difree_inode_chunk() helper. The new helper uses the existing
calculation if a chunk is not sparse. Otherwise, use the inobt record
holemask to free the contiguous regions of the chunk.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:20:10 +0000 (09:20 +1000)]
xfs: filter out sparse regions from individual inode allocation
Inode allocation from an existing record with free inodes traditionally
selects the first inode available according to the ir_free mask. With
sparse inode chunks, the ir_free mask could refer to an unallocated
region. We must mask the unallocated regions out of ir_free before using
it to select a free inode in the chunk.
Update the xfs_inobt_first_free_inode() helper to find the first free
inode available of the allocated regions of the inode chunk.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:19:29 +0000 (09:19 +1000)]
xfs: randomly do sparse inode allocations in DEBUG mode
Sparse inode allocations generally only occur when full inode chunk
allocation fails. This requires some level of filesystem space usage and
fragmentation.
For filesystems formatted with sparse inode chunks enabled, do random
sparse inode chunk allocs when compiled in DEBUG mode to increase test
coverage.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:18:32 +0000 (09:18 +1000)]
xfs: allocate sparse inode chunks on full chunk allocation failure
xfs_ialloc_ag_alloc() makes several attempts to allocate a full inode
chunk. If all else fails, reduce the allocation to the sparse length and
alignment and attempt to allocate a sparse inode chunk.
If sparse chunk allocation succeeds, check whether an inobt record
already exists that can track the chunk. If so, inherit and update the
existing record. Otherwise, insert a new record for the sparse chunk.
Create helpers to align sparse chunk inode records and insert or update
existing records in the inode btrees. The xfs_inobt_insert_sprec()
helper implements the merge or update semantics required for sparse
inode records with respect to both the inobt and finobt. To update the
inobt, either insert a new record or merge with an existing record. To
update the finobt, use the updated inobt record to either insert or
replace an existing record.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:09:05 +0000 (09:09 +1000)]
xfs: helper to convert holemask to inode alloc. bitmap
The inobt record holemask field is a condensed data type designed to fit
into the existing on-disk record and is zero based (allocated regions
are set to 0, sparse regions are set to 1) to provide backwards
compatibility. This makes the type somewhat complex for use in higher
level inode manipulations such as individual inode allocation, etc.
Rather than foist the complexity of dealing with this field to every bit
of logic that requires inode granular information, create a helper to
convert the holemask to an inode allocation bitmap. The inode allocation
bitmap is inode granularity similar to the inobt record free mask and
indicates which inodes of the chunk are physically allocated on disk,
irrespective of whether the inode is considered allocated or free by the
filesystem.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:06:30 +0000 (09:06 +1000)]
xfs: handle sparse inode chunks in icreate log recovery
Recovery of icreate transactions assumes hardcoded values for the inode
count and chunk length.
Sparse inode chunks are allocated in units of m_ialloc_min_blks. Update
the icreate validity checks to allow for appropriately sized inode
chunks and verify the inode count matches what is expected based on the
extent length rather than assuming a hardcoded count.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:05:49 +0000 (09:05 +1000)]
xfs: pass inode count through ordered icreate log item
v5 superblocks use an ordered log item for logging the initialization of
inode chunks. The icreate log item is currently hardcoded to an inode
count of 64 inodes.
The agbno and extent length are used to initialize the inode chunk from
log recovery. While an incorrect inode count does not lead to bad inode
chunk initialization, we should pass the correct inode count such that log
recovery has enough data to perform meaningful validity checks on the
chunk.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:04:19 +0000 (09:04 +1000)]
xfs: use actual inode count for sparse records in bulkstat/inumbers
The bulkstat and inumbers mechanisms make the assumption that inode
records consist of a full 64 inode chunk in several places. For example,
this is used to track how many inodes have been processed overall as
well as to determine whether a record has allocated inodes that must be
handled.
This assumption is invalid for sparse inode records. While sparse inodes
will be marked as free in the ir_free mask, they are not accounted as
free in ir_freecount because they cannot be allocated. Therefore,
ir_freecount may be less than 64 inodes in an inode record for which all
physically allocated inodes are free (and in turn ir_freecount < 64 does
not signify that the record has allocated inodes).
The new in-core inobt record format includes the ir_count field. This
holds the number of true, physical inodes tracked by the record. The
in-core ir_count field is always valid as it is hardcoded to
XFS_INODES_PER_CHUNK when sparse inodes is not enabled. Use ir_count to
handle inode records correctly in bulkstat in a generic manner.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 23:03:04 +0000 (09:03 +1000)]
xfs: introduce inode record hole mask for sparse inode chunks
The inode btrees track 64 inodes per record regardless of inode size.
Thus, inode chunks on disk vary in size depending on the size of the
inodes. This creates a contiguous allocation requirement for new inode
chunks that can be difficult to satisfy on an aged and fragmented (free
space) filesystems.
The inode record freecount currently uses 4 bytes on disk to track the
free inode count. With a maximum freecount value of 64, only one byte is
required. Convert the freecount field to a single byte and use two of
the remaining 3 higher order bytes left for the hole mask field. Use the
final leftover byte for the total count field.
The hole mask field tracks holes in the chunks of physical space that
the inode record refers to. This facilitates the sparse allocation of
inode chunks when contiguous chunks are not available and allows the
inode btrees to identify what portions of the chunk contain valid
inodes. The total count field contains the total number of valid inodes
referred to by the record. This can also be deduced from the hole mask.
The count field provides clarity and redundancy for internal record
verification.
Note that neither of the new fields can be written to disk on fs'
without sparse inode support. Doing so writes to the high-order bytes of
freecount and causes corruption from the perspective of older kernels.
The on-disk inobt record data structure is updated with a union to
distinguish between the original, "full" format and the new, "sparse"
format. The conversion routines to get, insert and update records are
updated to translate to and from the on-disk record accordingly such
that freecount remains a 4-byte value on non-supported fs, yet the new
fields of the in-core record are always valid with respect to the
record. This means that higher level code can refer to the current
in-core record format unconditionally and lower level code ensures that
records are translated to/from disk according to the capabilities of the
fs.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:58:32 +0000 (08:58 +1000)]
xfs: add fs geometry bit for sparse inode chunks
Define an fs geometry bit for sparse inode chunks such that the
characteristic of the fs can be identified by userspace.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:57:27 +0000 (08:57 +1000)]
xfs: sparse inode chunks feature helpers and mount requirements
The sparse inode chunks feature uses the helper function to enable the
allocation of sparse inode chunks. The incompatible feature bit is set
on disk at mkfs time to prevent mount from unsupported kernels.
Also, enforce the inode alignment requirements required for sparse inode
chunks at mount time. When enabled, full inode chunks (and all inode
record) alignment is increased from cluster size to inode chunk size.
Sparse inode alignment must match the cluster size of the fs. Both
superblock alignment fields are set as such by mkfs when sparse inode
support is enabled.
Finally, warn that sparse inode chunks is an experimental feature until
further notice.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:55:20 +0000 (08:55 +1000)]
xfs: use sparse chunk alignment for min. inode allocation requirement
xfs_ialloc_ag_select() iterates through the allocation groups looking
for free inodes or free space to determine whether to allow an inode
allocation to proceed. If no free inodes are available, it assumes that
an AG must have an extent longer than mp->m_ialloc_blks.
Sparse inode chunk support currently allows for allocations smaller than
the traditional inode chunk size specified in m_ialloc_blks. The current
minimum sparse allocation is set in the superblock sb_spino_align field
at mkfs time. Create a new m_ialloc_min_blks field in xfs_mount and use
this to represent the minimum supported allocation size for inode
chunks. Initialize m_ialloc_min_blks at mount time based on whether
sparse inodes are supported.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:54:03 +0000 (08:54 +1000)]
xfs: add sparse inode chunk alignment superblock field
Add sb_spino_align to the superblock to specify sparse inode chunk
alignment. This also currently represents the minimum allowable sparse
chunk allocation size.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Brian Foster [Thu, 28 May 2015 22:53:00 +0000 (08:53 +1000)]
xfs: support min/max agbno args in block allocator
The block allocator supports various arguments to tweak block allocation
behavior and set allocation requirements. The sparse inode chunk feature
introduces a new requirement not supported by the current arguments.
Sparse inode allocations must convert or merge into an inode record that
describes a fixed length chunk (64 inodes x inodesize). Full inode chunk
allocations by definition always result in valid inode records. Sparse
chunk allocations are smaller and the associated records can refer to
blocks not owned by the inode chunk. This model can result in invalid
inode records in certain cases.
For example, if a sparse allocation occurs near the start of an AG, the
aligned inode record for that chunk might refer to agbno 0. If an
allocation occurs towards the end of the AG and the AG size is not
aligned, the inode record could refer to blocks beyond the end of the
AG. While neither of these scenarios directly result in corruption, they
both insert invalid inode records and at minimum cause repair to
complain, are unlikely to merge into full chunks over time and set land
mines for other areas of code.
To guarantee sparse inode chunk allocation creates valid inode records,
support the ability to specify an agbno range limit for
XFS_ALLOCTYPE_NEAR_BNO block allocations. The min/max agbno's are
specified in the allocation arguments and limit the block allocation
algorithms to that range. The starting 'agbno' hint is clamped to the
range if the specified agbno is out of range. If no sufficient extent is
available within the range, the allocation fails. For backwards
compatibility, the min/max fields can be initialized to 0 to disable
range limiting (e.g., equivalent to min=0,max=agsize).
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:51:37 +0000 (08:51 +1000)]
xfs: update free inode record logic to support sparse inode records
xfs_difree_inobt() uses logic in a couple places that assume inobt
records refer to fully allocated chunks. Specifically, the use of
mp->m_ialloc_inos can cause problems for inode chunks that are sparsely
allocated. Sparse inode chunks can, by definition, define a smaller
number of inodes than a full inode chunk.
Fix the logic that determines whether an inode record should be removed
from the inobt to use the ir_free mask rather than ir_freecount. Fix the
agi counters modification to use ir_freecount to add the actual number
of inodes freed rather than assuming a full inode chunk.
Also make sure that we preserve the behavior to not remove inode chunks
if the block size is large enough for multiple inode chunks (e.g.,
bsize=64k, isize=512). This behavior was previously implicit in that in
such configurations, ir.freecount of a single record never matches
m_ialloc_inos. Hence, add some comments as well.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:50:21 +0000 (08:50 +1000)]
xfs: create individual inode alloc. helper
Inode allocation from sparse inode records must filter the ir_free mask
against ir_holemask. In preparation for this requirement, create a
helper to allocate an individual inode from an inode record.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Brian Foster [Thu, 28 May 2015 22:14:55 +0000 (08:14 +1000)]
xfs: fix broken i_nlink accounting for whiteout tmpfile inode
XFS uses the internal tmpfile() infrastructure for the whiteout inode
used for RENAME_WHITEOUT operations. For tmpfile inodes, XFS allocates
the inode, drops di_nlink, adds the inode to the agi unlinked list,
calls d_tmpfile() which correspondingly drops i_nlink of the vfs inode,
and then finishes the common inode setup (e.g., clear I_NEW and unlock).
The d_tmpfile() call was originally made inxfs_create_tmpfile(), but was
pulled up out of that function as part of the following commit to
resolve a deadlock issue:
330033d6 xfs: fix tmpfile/selinux deadlock and initialize security
As a result, callers of xfs_create_tmpfile() are responsible for either
calling d_tmpfile() or fixing up i_nlink appropriately. The whiteout
tmpfile allocation helper does neither. As a result, the vfs ->i_nlink
becomes inconsistent with the on-disk ->di_nlink once xfs_rename() links
it back into the source dentry and calls xfs_bumplink().
Update the assert in xfs_rename() to help detect this problem in the
future and update xfs_rename_alloc_whiteout() to decrement the link
count as part of the manual tmpfile inode setup.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 28 May 2015 21:40:32 +0000 (07:40 +1000)]
xfs: xfs_iozero can return positive errno
It was missed when we converted everything in XFs to use negative error
numbers, so fix it now. Bug introduced in 3.17 by commit
2451337 ("xfs: global
error sign conversion"), and should go back to stable kernels.
Thanks to Brian Foster for noticing it.
cc: <stable@vger.kernel.org> # 3.17, 3.18, 3.19, 4.0
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 28 May 2015 21:40:08 +0000 (07:40 +1000)]
xfs: xfs_attr_inactive leaves inconsistent attr fork state behind
xfs_attr_inactive() is supposed to clean up the attribute fork when
the inode is being freed. While it removes attribute fork extents,
it completely ignores attributes in local format, which means that
there can still be active attributes on the inode after
xfs_attr_inactive() has run.
This leads to problems with concurrent inode writeback - the in-core
inode attribute fork is removed without locking on the assumption
that nothing will be attempting to access the attribute fork after a
call to xfs_attr_inactive() because it isn't supposed to exist on
disk any more.
To fix this, make xfs_attr_inactive() completely remove all traces
of the attribute fork from the inode, regardless of it's state.
Further, also remove the in-core attribute fork structure safely so
that there is nothing further that needs to be done by callers to
clean up the attribute fork. This means we can remove the in-core
and on-disk attribute forks atomically.
Also, on error simply remove the in-memory attribute fork. There's
nothing that can be done with it once we have failed to remove the
on-disk attribute fork, so we may as well just blow it away here
anyway.
cc: <stable@vger.kernel.org> # 3.12 to 4.0
Reported-by: Waiman Long <waiman.long@hp.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 28 May 2015 21:40:06 +0000 (07:40 +1000)]
xfs: extent size hints can round up extents past MAXEXTLEN
This results in BMBT corruption, as seen by this test:
# mkfs.xfs -f -d size=
40051712b,agcount=4 /dev/vdc
....
# mount /dev/vdc /mnt/scratch
# xfs_io -ft -c "extsize 16m" -c "falloc 0 30g" -c "bmap -vp" /mnt/scratch/foo
which results in this failure on a debug kernel:
XFS: Assertion failed: (blockcount & xfs_mask64hi(64-BMBT_BLOCKCOUNT_BITLEN)) == 0, file: fs/xfs/libxfs/xfs_bmap_btree.c, line: 211
....
Call Trace:
[<
ffffffff814cf0ff>] xfs_bmbt_set_allf+0x8f/0x100
[<
ffffffff814cf18d>] xfs_bmbt_set_all+0x1d/0x20
[<
ffffffff814f2efe>] xfs_iext_insert+0x9e/0x120
[<
ffffffff814c7956>] ? xfs_bmap_add_extent_hole_real+0x1c6/0xc70
[<
ffffffff814c7956>] xfs_bmap_add_extent_hole_real+0x1c6/0xc70
[<
ffffffff814caaab>] xfs_bmapi_write+0x72b/0xed0
[<
ffffffff811c72ac>] ? kmem_cache_alloc+0x15c/0x170
[<
ffffffff814fe070>] xfs_alloc_file_space+0x160/0x400
[<
ffffffff81ddcc29>] ? down_write+0x29/0x60
[<
ffffffff815063eb>] xfs_file_fallocate+0x29b/0x310
[<
ffffffff811d2bc8>] ? __sb_start_write+0x58/0x120
[<
ffffffff811e3e18>] ? do_vfs_ioctl+0x318/0x570
[<
ffffffff811cd680>] vfs_fallocate+0x140/0x260
[<
ffffffff811ce6f8>] SyS_fallocate+0x48/0x80
[<
ffffffff81ddec09>] system_call_fastpath+0x12/0x17
The tracepoint that indicates the extent that triggered the assert
failure is:
xfs_iext_insert: idx 0 offset 0 block
16777224 count
2097152 flag 1
Clearly indicating that the extent length is greater than MAXEXTLEN,
which is
2097151. A prior trace point shows the allocation was an
exact size match and that a length greater than MAXEXTLEN was asked
for:
xfs_alloc_size_done: agno 1 agbno 8 minlen
2097152 maxlen
2097152
^^^^^^^ ^^^^^^^
We don't see this problem with extent size hints through the IO path
because we can't do single IOs large enough to trigger MAXEXTLEN
allocation. fallocate(), OTOH, is not limited in it's allocation
sizes and so needs help here.
The issue is that the extent size hint alignment is rounding up the
extent size past MAXEXTLEN, because xfs_bmapi_write() is not taking
into account extent size hints when calculating the maximum extent
length to allocate. xfs_bmapi_reserve_delalloc() is already doing
this, but direct extent allocation is not.
Unfortunately, the calculation in xfs_bmapi_reserve_delalloc() is
wrong, and it works only because delayed allocation extents are not
limited in size to MAXEXTLEN in the in-core extent tree. hence this
calculation does not work for direct allocation, and the delalloc
code needs fixing. This may, in fact be the underlying bug that
occassionally causes transaction overruns in delayed allocation
extent conversion, so now we know it's wrong we should fix it, too.
Many thanks to Brian Foster for finding this problem during review
of this patch.
Hence the fix, after much code reading, is to allow
xfs_bmap_extsize_align() to align partial extents when full
alignment would extend the alignment past MAXEXTLEN. We can safely
do this because all callers have higher layer allocation loops that
already handle short allocations, and so will simply run another
allocation to cover the remainder of the requested allocation range
that we ignored during alignment. The advantage of this approach is
that it also removes the need for callers to do anything other than
limit their requests to MAXEXTLEN - they don't really need to be
aware of extent size hints at all.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 28 May 2015 21:39:34 +0000 (07:39 +1000)]
xfs: inode and free block counters need to use __percpu_counter_compare
Because the counters use a custom batch size, the comparison
functions need to be aware of that batch size otherwise the
comparison does not work correctly. This leads to ASSERT failures
on generic/027 like this:
XFS: Assertion failed: 0, file: fs/xfs/xfs_mount.c, line: 1099
------------[ cut here ]------------
....
Call Trace:
[<
ffffffff81522a39>] xfs_mod_icount+0x99/0xc0
[<
ffffffff815285cb>] xfs_trans_unreserve_and_mod_sb+0x28b/0x5b0
[<
ffffffff8152f941>] xfs_log_commit_cil+0x321/0x580
[<
ffffffff81528e17>] xfs_trans_commit+0xb7/0x260
[<
ffffffff81503d4d>] xfs_bmap_finish+0xcd/0x1b0
[<
ffffffff8151da41>] xfs_inactive_ifree+0x1e1/0x250
[<
ffffffff8151dbe0>] xfs_inactive+0x130/0x200
[<
ffffffff81523a21>] xfs_fs_evict_inode+0x91/0xf0
[<
ffffffff811f3958>] evict+0xb8/0x190
[<
ffffffff811f433b>] iput+0x18b/0x1f0
[<
ffffffff811e8853>] do_unlinkat+0x1f3/0x320
[<
ffffffff811d548a>] ? filp_close+0x5a/0x80
[<
ffffffff811e999b>] SyS_unlinkat+0x1b/0x40
[<
ffffffff81e0892e>] system_call_fastpath+0x12/0x71
This is a regression introduced by commit
501ab32 ("xfs: use generic
percpu counters for inode counter").
This patch fixes the same problem for both the inode counter and the
free block counter in the superblocks.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Thu, 28 May 2015 21:39:34 +0000 (07:39 +1000)]
percpu_counter: batch size aware __percpu_counter_compare()
XFS uses non-stanard batch sizes for avoiding frequent global
counter updates on it's allocated inode counters, as they increment
or decrement in batches of 64 inodes. Hence the standard percpu
counter batch of 32 means that the counter is effectively a global
counter. Currently Xfs uses a batch size of 128 so that it doesn't
take the global lock on every single modification.
However, Xfs also needs to compare accurately against zero, which
means we need to use percpu_counter_compare(), and that has a
hard-coded batch size of 32, and hence will spuriously fail to
detect when it is supposed to use precise comparisons and hence
the accounting goes wrong.
Add __percpu_counter_compare() to take a custom batch size so we can
use it sanely in XFS and factor percpu_counter_compare() to use it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dave Chinner <david@fromorbit.com>
George Wang [Thu, 28 May 2015 21:39:34 +0000 (07:39 +1000)]
xfs: use percpu_counter_read_positive for mp->m_icount
Function percpu_counter_read just return the current counter, which can be
negative. This will cause the checking of "allocated inode
counts <= m_maxicount" false positive. Use percpu_counter_read_positive can
solve this problem, and be consistent with the purpose to introduce percpu
mechanism to xfs.
Signed-off-by: George Wang <xuw2015@gmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Linus Torvalds [Mon, 4 May 2015 02:22:23 +0000 (19:22 -0700)]
Linux 4.1-rc2
Linus Torvalds [Mon, 4 May 2015 01:23:53 +0000 (18:23 -0700)]
Merge tag 'for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some miscellaneous bug fixes and some final on-disk and ABI changes
for ext4 encryption which provide better security and performance"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix growing of tiny filesystems
ext4: move check under lock scope to close a race.
ext4: fix data corruption caused by unwritten and delayed extents
ext4 crypto: remove duplicated encryption mode definitions
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
ext4 crypto: add padding to filenames before encrypting
ext4 crypto: simplify and speed up filename encryption
Linus Torvalds [Mon, 4 May 2015 01:15:48 +0000 (18:15 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One intel fix, one rockchip fix, and a bunch of radeon fixes for some
regressions from audio rework and vm stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915/chv: Implement WaDisableShadowRegForCpd
drm/radeon: fix userptr return value checking (v2)
drm/radeon: check new address before removing old one
drm/radeon: reset BOs address after clearing it.
drm/radeon: fix lockup when BOs aren't part of the VM on release
drm/radeon: add SI DPM quirk for Sapphire R9 270 Dual-X 2G GDDR5
drm/radeon: adjust pll when audio is not enabled
drm/radeon: only enable audio streams if the monitor supports it
drm/radeon: only mark audio as connected if the monitor supports it (v3)
drm/radeon/audio: don't enable packets until the end
drm/radeon: drop dce6_dp_enable
drm/radeon: fix ordering of AVI packet setup
drm/radeon: Use drm_calloc_ab for CS relocs
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
Dave Airlie [Sun, 3 May 2015 22:56:47 +0000 (08:56 +1000)]
Merge tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Just a single intel fix
* tag 'drm-intel-fixes-2015-04-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/chv: Implement WaDisableShadowRegForCpd
Dave Airlie [Sun, 3 May 2015 22:56:27 +0000 (08:56 +1000)]
Merge branch 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
one fix and maintainers update
* 'drm-next0420' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: fix error check when getting irq
MAINTAINERS: add entry for Rockchip drm drivers
Linus Torvalds [Sun, 3 May 2015 20:22:32 +0000 (13:22 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three logical fixes (as 5 patches).
The 3ware class of drivers were causing an oops with multiqueue by
tearing down the command mappings after completing the command (where
the variables in the command used to tear down the mapping were
no-longer valid). There's also a fix for the qnap iscsi target which
was choking on us sending it commands that were too long and a fix for
the reworked aha1542 allocating GFP_KERNEL under a lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: fix command completion race
3w-xxxx: fix command completion race
3w-sas: fix command completion race
aha1542: Allocate memory before taking a lock
SCSI: add 1024 max sectors black list flag
Linus Torvalds [Sun, 3 May 2015 17:49:04 +0000 (10:49 -0700)]
Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave dmaengine fixes from Vinod Koul:
"Here are the fixes in dmaengine subsystem for rc2:
- privatecnt fix for slave dma request API by Christopher
- warn fix for PM ifdef in usb-dmac by Geert
- fix hardware dependency for xgene by Jean"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: increment privatecnt when using dma_get_any_slave_channel
dmaengine: xgene: Set hardware dependency
dmaengine: usb-dmac: Protect PM-only functions to kill warning
Linus Torvalds [Sun, 3 May 2015 17:28:36 +0000 (10:28 -0700)]
Merge tag 'powerpc-4.1-3' of git://git./linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
Jan Kara [Sun, 3 May 2015 03:58:32 +0000 (23:58 -0400)]
ext4: fix growing of tiny filesystems
The estimate of necessary transaction credits in ext4_flex_group_add()
is too pessimistic. It reserves credit for sb, resize inode, and resize
inode dindirect block for each group added in a flex group although they
are always the same block and thus it is enough to account them only
once. Also the number of modified GDT block is overestimated since we
fit EXT4_DESC_PER_BLOCK(sb) descriptors in one block.
Make the estimation more precise. That reduces number of requested
credits enough that we can grow 20 MB filesystem (which has 1 MB
journal, 79 reserved GDT blocks, and flex group size 16 by default).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Davide Italiano [Sun, 3 May 2015 03:21:15 +0000 (23:21 -0400)]
ext4: move check under lock scope to close a race.
fallocate() checks that the file is extent-based and returns
EOPNOTSUPP in case is not. Other tasks can convert from and to
indirect and extent so it's safe to check only after grabbing
the inode mutex.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Lukas Czerner [Sun, 3 May 2015 01:36:55 +0000 (21:36 -0400)]
ext4: fix data corruption caused by unwritten and delayed extents
Currently it is possible to lose whole file system block worth of data
when we hit the specific interaction with unwritten and delayed extents
in status extent tree.
The problem is that when we insert delayed extent into extent status
tree the only way to get rid of it is when we write out delayed buffer.
However there is a limitation in the extent status tree implementation
so that when inserting unwritten extent should there be even a single
delayed block the whole unwritten extent would be marked as delayed.
At this point, there is no way to get rid of the delayed extents,
because there are no delayed buffers to write out. So when a we write
into said unwritten extent we will convert it to written, but it still
remains delayed.
When we try to write into that block later ext4_da_map_blocks() will set
the buffer new and delayed and map it to invalid block which causes
the rest of the block to be zeroed loosing already written data.
For now we can fix this by simply not allowing to set delayed status on
written extent in the extent status tree. Also add WARN_ON() to make
sure that we notice if this happens in the future.
This problem can be easily reproduced by running the following xfs_io.
xfs_io -f -c "pwrite -S 0xaa 4096 2048" \
-c "falloc 0 131072" \
-c "pwrite -S 0xbb 65536 2048" \
-c "fsync" /mnt/test/fff
echo 3 > /proc/sys/vm/drop_caches
xfs_io -c "pwrite -S 0xdd 67584 2048" /mnt/test/fff
This can be theoretically also reproduced by at random by running fsx,
but it's not very reliable, though on machines with bigger page size
(like ppc) this can be seen more often (especially xfstest generic/127)
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Chanho Park [Sat, 2 May 2015 14:29:22 +0000 (10:29 -0400)]
ext4 crypto: remove duplicated encryption mode definitions
This patch removes duplicated encryption modes which were already in
ext4.h. They were duplicated from commit
3edc18d and commit f542fb.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Herbert Xu [Sat, 2 May 2015 14:29:19 +0000 (10:29 -0400)]
ext4 crypto: do not select from EXT4_FS_ENCRYPTION
This patch adds a tristate EXT4_ENCRYPTION to do the selections
for EXT4_FS_ENCRYPTION because selecting from a bool causes all
the selected options to be built-in, even if EXT4 itself is a
module.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sat, 2 May 2015 03:51:04 +0000 (20:51 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Receive packet length needs to be adjust by 2 on RX to accomodate
the two padding bytes in altera_tse driver. From Vlastimil Setka.
2) If rx frame is dropped due to out of memory in macb driver, we leave
the receive ring descriptors in an undefined state. From Punnaiah
Choudary Kalluri
3) Some netlink subsystems erroneously signal NLM_F_MULTI. That is
only for dumps. Fix from Nicolas Dichtel.
4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
the ipv4_mtu() helper. From Herbert Xu.
5) Fix null deref in bridge netfilter, and miscalculated lengths in
jump/goto nf_tables verdicts. From Florian Westphal.
6) Unhash ping sockets properly.
7) Software implementation of BPF divide did 64/32 rather than 64/64
bit divide. The JITs got it right. Fix from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
ipv4: Missing sk_nulls_node_init() in ping_unhash().
net: fec: Fix RGMII-ID mode
net/mlx4_en: Schedule napi when RX buffers allocation fails
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
net/mlx4_core: Fix unaligned accesses
mlx4_en: Use correct loop cursor in error path.
cxgb4: Fix MC1 memory offset calculation
bnx2x: Delay during kdump load
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
net: dsa: Fix scope of eeprom-length property
net: macb: Fix race condition in driver when Rx frame is dropped
hv_netvsc: Fix a bug in netvsc_start_xmit()
altera_tse: Correct rx packet length
mlx4: Fix tx ring affinity_mask creation
tipc: fix problem with parallel link synchronization mechanism
tipc: remove wrong use of NLM_F_MULTI
bridge/nl: remove wrong use of NLM_F_MULTI
bridge/mdb: remove wrong use of NLM_F_MULTI
net: sched: act_connmark: don't zap skb->nfct
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
...
Stefan Hajnoczi [Fri, 1 May 2015 23:12:29 +0000 (08:42 +0930)]
virtio: fix typo in vring_need_event() doc comment
Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rusty Russell [Fri, 1 May 2015 23:12:38 +0000 (08:42 +0930)]
virtio: pass baton to Michael Tsirkin
With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.
This makes it clear that Michael is in charge. He's good, but having
me watch over his shoulder won't help.
Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 2 May 2015 03:35:39 +0000 (20:35 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph RBD fix from Sage Weil.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: end I/O the entire obj_request on error
David S. Miller [Sat, 2 May 2015 02:02:47 +0000 (22:02 -0400)]
ipv4: Missing sk_nulls_node_init() in ping_unhash().
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Wen Xu <hotdog3645@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya Dryomov [Sat, 25 Apr 2015 12:56:15 +0000 (15:56 +0300)]
rbd: end I/O the entire obj_request on error
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
rbd_assert(more ^ (which == img_request->obj_request_count));
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Shawn Edwards <lesser.evil@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Theodore Ts'o [Fri, 1 May 2015 20:56:50 +0000 (16:56 -0400)]
ext4 crypto: add padding to filenames before encrypting
This obscures the length of the filenames, to decrease the amount of
information leakage. By default, we pad the filenames to the next 4
byte boundaries. This costs nothing, since the directory entries are
aligned to 4 byte boundaries anyway. Filenames can also be padded to
8, 16, or 32 bytes, which will consume more directory space.
Change-Id: Ibb7a0fb76d2c48e2061240a709358ff40b14f322
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Theodore Ts'o [Fri, 1 May 2015 20:56:45 +0000 (16:56 -0400)]
ext4 crypto: simplify and speed up filename encryption
Avoid using SHA-1 when calculating the user-visible filename when the
encryption key is available, and avoid decrypting lots of filenames
when searching for a directory entry in a directory block.
Change-Id: If4655f144784978ba0305b597bfa1c8d7bb69e63
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Fri, 1 May 2015 14:46:21 +0000 (07:46 -0700)]
Merge branch 'for-linus-4.1' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"A few more btrfs fixes.
These range from corners Filipe found in the new free space cache
writeback to a grab bag of fixes from the list"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
btrfs: unlock i_mutex after attempting to delete subvolume during send
btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
btrfs: fix race on ENOMEM in alloc_extent_buffer
btrfs: handle ENOMEM in btrfs_alloc_tree_block
Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
Btrfs: don't check for delalloc_bytes in cache_save_setup
Btrfs: fix deadlock when starting writeback of bg caches
Btrfs: fix race between start dirty bg cache writeout and bg deletion
Linus Torvalds [Fri, 1 May 2015 14:44:32 +0000 (07:44 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
Sam Bobroff [Fri, 1 May 2015 06:50:34 +0000 (16:50 +1000)]
powerpc/powernv: Restore non-volatile CRs after nap
Patches
7cba160ad "powernv/cpuidle: Redesign idle states management"
and
77b54e9f2 "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.
Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.
This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.
The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.
When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.
Fixes: 7cba160ad789 ("powernv/cpuidle: Redesign idle states management")
Fixes: 77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 30 Apr 2015 23:22:15 +0000 (09:22 +1000)]
powerpc/eeh: Delay probing EEH device during hotplug
Commit
1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes: ff57b454ddb9 ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 30 Apr 2015 23:14:11 +0000 (09:14 +1000)]
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes: 28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nathan Fontenot [Thu, 30 Apr 2015 01:42:06 +0000 (20:42 -0500)]
powerpc/pseries: Correct cpu affinity for dlpar added cpus
The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.
This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.
Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.
Fixes: 1a8061c46c46 ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 1 May 2015 01:10:09 +0000 (11:10 +1000)]
selftests/powerpc: Fix the pmu install rule
My patch to add install support for the powerpc selftests had a typo,
leading to the three tests in the pmu directory itself not being
installed.
Fixes: 6faeeea44b84 ("selftests: Add install support for the powerpc tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds [Thu, 30 Apr 2015 21:23:31 +0000 (14:23 -0700)]
Merge tag 'pm+acpi-4.1-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Three regression fixes this time, one for a recent regression in the
cpuidle core affecting multiple systems, one for an inadvertently
added duplicate typedef in ACPICA that breaks compilation with GCC 4.5
and one for an ACPI Smart Battery Subsystem driver regression
introduced during the 3.18 cycle (stable-candidate).
Specifics:
- Fix for a regression in the cpuidle core introduced by one of the
recent commits in the clockevents_notify() removal series that put
a call to a function which had to be executed with disabled
interrupts into a code path running with enabled interrupts (Rafael
J Wysocki)
- Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
of the recent ACPICA tools commits that added a duplicate typedef
to one of the ACPICA's header files by mistake (Olaf Hering)
- Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
driver introduced during the 3.18 development cycle causing the
smart battery manager to be marked as not present when it should be
marked as present (Chris Bainbridge)"
* tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Run tick_broadcast_exit() with disabled interrupts
ACPI / SBS: Enable battery manager when present
ACPICA: remove duplicate u8 typedef
Linus Torvalds [Thu, 30 Apr 2015 21:00:18 +0000 (14:00 -0700)]
Merge tag 'sound-4.1-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"One nice fix is Peter's patch to make the old good SB Audigy PCI to
work with 32bit DMA instead of 31bit. This allows the MIDI synth
running on modern machines again. Along with it, a few fixes for
emu10k1 have merged.
In ASoC side, there is one fix in the common code, but it's just
trivial additions of static inline functions for CONFIG_PM=n. The
rest are various device-specific small fixes.
Last but not least, a few HD-audio fixes are included, as usual, too"
* tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ASoC: rt5677: fixed wrong DMIC ref clock
ALSA: emu10k1: Emu10k2 32 bit DMA mode
ALSA: emux: Fix mutex deadlock in OSS emulation
ASoC: Update email-id of Rajeev Kumar
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ALSA: hda - Fix missing va_end() call in snd_hda_codec_pcm_new()
ALSA: emux: Fix mutex deadlock at unloading
ALSA: emu10k1: Fix card shortname string buffer overflow
ALSA: hda - Add mute-LED mode control to Thinkpad
ALSA: hda - Fix mute-LED fixed mode
ALSA: hda - Fix click noise at start on Dell XPS13
ASoC: rt5645: Add ACPI match ID
ASoC: rt5677: add register patch for PLL
ASoC: Intel: fix the makefile for atom code
ASoC: dapm: Enable autodisable on SOC_DAPM_SINGLE_TLV_AUTODISABLE
ASoC: add static inline funcs to fix a compiling issue
ASoC: Intel: sst_byt: remove kfree for memory allocated with devm_kzalloc
ASoC: samsung: s3c24xx-i2s: Fix return value check in s3c24xx_iis_dev_probe()
ASoC: tfa9879: Fix return value check in tfa9879_i2c_probe()
ASoC: fsl_ssi: Fix platform_get_irq() error handling
...
Markus Pargmann [Thu, 30 Apr 2015 15:07:50 +0000 (17:07 +0200)]
net: fec: Fix RGMII-ID mode
RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.
So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 30 Apr 2015 14:32:46 +0000 (17:32 +0300)]
net/mlx4_en: Schedule napi when RX buffers allocation fails
When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Camuso [Thu, 30 Apr 2015 11:51:27 +0000 (07:51 -0400)]
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 29 Apr 2015 20:52:51 +0000 (16:52 -0400)]
net/mlx4_core: Fix unaligned accesses
Addresses the following kernel logs seen during boot:
Kernel unaligned access at TPC[
100ee150] mlx4_QUERY_HCA+0x80/0x248 [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[
100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Wed, 29 Apr 2015 22:59:35 +0000 (15:59 -0700)]
mlx4_en: Use correct loop cursor in error path.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Fixes: 9e311e7 ("net/mlx4_en: Use affinity hint")
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael J. Wysocki [Thu, 30 Apr 2015 19:05:57 +0000 (21:05 +0200)]
Merge branches 'acpica', 'acpi-battery' and 'pm-cpuidle'
Takashi Iwai [Thu, 30 Apr 2015 17:08:06 +0000 (19:08 +0200)]
Merge tag 'asoc-v4.1-rc1' of git://git./linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.1
A few fixes for v4.1, none earth shattering and mostly driver related
except for one change to fix !PM builds for Intel platforms which is
done by adding stubs in the core so other platforms don't run into the
same issue.