firefly-linux-kernel-4.4.55.git
9 years agomwifiex: update AP WMM settings from BSS_START event
Avinash Patil [Wed, 3 Jun 2015 11:29:45 +0000 (16:59 +0530)]
mwifiex: update AP WMM settings from BSS_START event

This was missing and would cause issue in WMM handling.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: advertise PS ON by default support to cfg80211
Avinash Patil [Wed, 3 Jun 2015 11:29:44 +0000 (16:59 +0530)]
mwifiex: advertise PS ON by default support to cfg80211

This would enable driver to enter powersave as soon as connected.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: drop block-ack action frames
Avinash Patil [Wed, 3 Jun 2015 11:29:43 +0000 (16:59 +0530)]
mwifiex: drop block-ack action frames

We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: support downloading IEs from tail
Avinash Patil [Wed, 3 Jun 2015 11:29:42 +0000 (16:59 +0530)]
mwifiex: support downloading IEs from tail

Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: parse power constraint IE from Tail
Avinash Patil [Wed, 3 Jun 2015 11:29:41 +0000 (16:59 +0530)]
mwifiex: parse power constraint IE from Tail

This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: dump station support in uap mode
Xinming Hu [Wed, 3 Jun 2015 11:29:40 +0000 (16:59 +0530)]
mwifiex: dump station support in uap mode

This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: add sta_list firmware command
Xinming Hu [Wed, 3 Jun 2015 11:29:39 +0000 (16:59 +0530)]
mwifiex: add sta_list firmware command

This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: maintain station statistic in uap mode
Xinming Hu [Wed, 3 Jun 2015 11:29:38 +0000 (16:59 +0530)]
mwifiex: maintain station statistic in uap mode

This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: add cfg80211 get_channel handler
Xinming Hu [Wed, 3 Jun 2015 11:29:37 +0000 (16:59 +0530)]
mwifiex: add cfg80211 get_channel handler

This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: disable CAC upon radar detection event
Avinash Patil [Wed, 3 Jun 2015 11:29:36 +0000 (16:59 +0530)]
mwifiex: disable CAC upon radar detection event

This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: reset 11h active flag when chandef does not require dfs
Avinash Patil [Wed, 3 Jun 2015 11:29:35 +0000 (16:59 +0530)]
mwifiex: reset 11h active flag when chandef does not require dfs

This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: enable 11d after bss reset
Avinash Patil [Wed, 3 Jun 2015 11:29:34 +0000 (16:59 +0530)]
mwifiex: enable 11d after bss reset

BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: support AP reset after bss_stop
Avinash Patil [Wed, 3 Jun 2015 11:29:33 +0000 (16:59 +0530)]
mwifiex: support AP reset after bss_stop

This would enable clearing of FW bss data structures when AP
operations are stopped.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: correct bss_type assignment
Avinash Patil [Wed, 3 Jun 2015 11:29:32 +0000 (16:59 +0530)]
mwifiex: correct bss_type assignment

Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: verbose logging for association failure messages
Avinash Patil [Wed, 3 Jun 2015 11:29:31 +0000 (16:59 +0530)]
mwifiex: verbose logging for association failure messages

This patch adds more detailed information about association failures
 - reason and states.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agoath9k: fix DMA stop sequence for AR9003+
Felix Fietkau [Tue, 2 Jun 2015 08:38:32 +0000 (10:38 +0200)]
ath9k: fix DMA stop sequence for AR9003+

AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agowl1251: drop unneeded goto
Julia Lawall [Thu, 28 May 2015 21:02:20 +0000 (23:02 +0200)]
wl1251: drop unneeded goto

Delete jump to a label on the next line, when that label is not
used elsewhere.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier l;
@@

-if (...) goto l;
-l:
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agotcp: double default TSQ output bytes limit
Wei Liu [Wed, 3 Jun 2015 10:10:42 +0000 (11:10 +0100)]
tcp: double default TSQ output bytes limit

Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.

This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.

Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agotcp: remove redundant checks
Eric Dumazet [Thu, 4 Jun 2015 06:49:21 +0000 (23:49 -0700)]
tcp: remove redundant checks

tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():

if (th->doff < sizeof(struct tcphdr) / 4)
    goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
    goto discard_it;

So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.

if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;

A second check can be removed after no_tcp_socket label for same reason.

Same tests can be removed in tcp_v6_do_rcv()

Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoMerge branch 'switchdev-next'
David S. Miller [Thu, 4 Jun 2015 06:47:24 +0000 (23:47 -0700)]
Merge branch 'switchdev-next'

Scott Feldman says:

====================
switchdev: documentation updates

Update the switchdev documentation to clarify that for IPV4 FIB object, the add
op is used for both adding and modifying the FIB entry on the device.

I found a few other white-space and grammer issues to fix, and to clarify the
static FDB ops.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoswitchdev: documentation: use switchdev_port_obj_xxx for IPv4 FIB add/modify/delete ops
Scott Feldman [Thu, 4 Jun 2015 03:43:43 +0000 (20:43 -0700)]
switchdev: documentation: use switchdev_port_obj_xxx for IPv4 FIB add/modify/delete ops

Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.

Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoswitchdev: documentation: for static FDB ops, use switchdev_port_fdb_xxx ops
Scott Feldman [Thu, 4 Jun 2015 03:43:42 +0000 (20:43 -0700)]
switchdev: documentation: for static FDB ops, use switchdev_port_fdb_xxx ops

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoswitchdev: documentation: fix grammer error
Scott Feldman [Thu, 4 Jun 2015 03:43:41 +0000 (20:43 -0700)]
switchdev: documentation: fix grammer error

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoswitchdev: documentation: fix longer-than-80-char lines
Scott Feldman [Thu, 4 Jun 2015 03:43:40 +0000 (20:43 -0700)]
switchdev: documentation: fix longer-than-80-char lines

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoMerge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git.kernel.org/pub...
David S. Miller [Thu, 4 Jun 2015 06:44:57 +0000 (23:44 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git./linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U

ath10k:

* qca6174 power consumption improvements, enable ASPM etc (Michal)

wil6210:

* support Wi-Fi Simple Configuration in STA mode

iwlwifi:

* a few fixes (re-enablement of interrupts for certain new
  platforms that have special power states)
* Rework completely the RBD allocation model towards new
  multi RX hardware.
* cleanups
* scan reworks continuation (Luca)

mwifiex:

* improve firmware debug functionality

rtlwifi:

* update regulatory database

brcmfmac:

* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================

Conflicts:
drivers/net/wireless/iwlwifi/Kconfig

Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.

Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoMerge branch 'cxgb4-next'
David S. Miller [Thu, 4 Jun 2015 06:40:20 +0000 (23:40 -0700)]
Merge branch 'cxgb4-next'

Hariprasad Shenai says:

====================
cxgb4: Adds support for various ethtool stats

This patch series adds the following:
Adds support to dump adapter specific stats in ethtool
Adds support to dump channel stats in ethtool
Adds support to dump loopback port stats in ethtool
Remove wake-on-lan get/set ethtool support

This patch series has been created against net-next tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agocxgb4: Remove WOL get/set ethtool support
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:42 +0000 (21:04 +0530)]
cxgb4: Remove WOL get/set ethtool support

Remove ethtool get/set support for wake on lan, adapter doesn't support
it.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agocxgb4: Add support to dump loopback port stats
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:41 +0000 (21:04 +0530)]
cxgb4: Add support to dump loopback port stats

Add support in ethtool to dump loopback port statistics

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agocxgb4: Add support in ethtool to dump channel stats
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:40 +0000 (21:04 +0530)]
cxgb4: Add support in ethtool to dump channel stats

Add support in ethtool to dump adapter channel stats

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agocxgb4: Add ethtool support to get adapter stats
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:39 +0000 (21:04 +0530)]
cxgb4: Add ethtool support to get adapter stats

Add ethtool support to get adapter specific hardware statistics

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoMerge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
David S. Miller [Thu, 4 Jun 2015 03:22:46 +0000 (20:22 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge

Antonio Quartulli says:

====================
pull request: batman-adv 20150603

here you have our second batch of patches intended for net-next.

In this patchset you won't find any new features, but quite some code
cleanup work, a bunch of code style fixes and also comments corrections
by Markus Pargmann.

Moreover you have a patch from Sven Eckelmann removing an unnecessary
NULL check in batadv_iv_ogm_update_seqnos().

Please pull or let me know of any problem!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agonet: tulip: rearrange order of searching for substrings
Rasmus Villemoes [Wed, 3 Jun 2015 11:44:03 +0000 (13:44 +0200)]
net: tulip: rearrange order of searching for substrings

Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next...
David S. Miller [Thu, 4 Jun 2015 03:19:16 +0000 (20:19 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-06-03

This series contains updates to e1000e only.

Yanir provides 8 fixes and 1 version bump for e1000e.  First fix resolves
a possible unit hang if multiple descriptors are available in the rings
during reset or runtime suspend.  Fixed a warning on SPARC compile based
on a suggested solution from Alex Duyck.  Fixed a logical error, where
a "if" condition under which a flush should occur, was revered.  Fixed
a hardware issue that prevented i219 from working in legacy interrupts
mode.  Fixed the hardware clock configuration and suprious non-linear
increment.  Lastly, fixed a system hang which occurred during execution
of "ethtool -t <NIC>", by disabling MULR for the loopback test to avoid
the hand state.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agobpf: introduce bpf_clone_redirect() helper
Alexei Starovoitov [Tue, 2 Jun 2015 23:03:14 +0000 (16:03 -0700)]
bpf: introduce bpf_clone_redirect() helper

Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.

Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agonet/mlx4_core: fix typo in mlx4_set_vf_mac
Carol Soto [Tue, 2 Jun 2015 21:07:25 +0000 (16:07 -0500)]
net/mlx4_core: fix typo in mlx4_set_vf_mac

fix typo in mlx4_set_vf_mac

Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agonet/mlx4_core: need to call close fw if alloc icm is called twice
Carol Soto [Tue, 2 Jun 2015 21:07:24 +0000 (16:07 -0500)]
net/mlx4_core: need to call close fw if alloc icm is called twice

If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.

Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agonet/mlx4_core: double free of dev_vfs
Carol L Soto [Tue, 2 Jun 2015 21:07:23 +0000 (16:07 -0500)]
net/mlx4_core: double free of dev_vfs

If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.

Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agodrivers/net/ethernet/dec/tulip/uli526x.c: fix misleading indentation in uli526x_timer
David Malcolm [Tue, 2 Jun 2015 19:31:17 +0000 (15:31 -0400)]
drivers/net/ethernet/dec/tulip/uli526x.c: fix misleading indentation in uli526x_timer

This code in drivers/net/ethernet/dec/tulip/uli526x.c
function "uli526x_timer":

  1086          } else
  1087                  if ((tmp_cr12 & 0x3) && db->link_failed) {
  [...snip...]
  1109                  }
  1110                  else if(!(tmp_cr12 & 0x3) && db->link_failed)
  1111                  {
  [...snip...]
  1117                  }
  1118                  db->init=0;

is misleadingly indented: the
  db->init=0
is indented as if part of the else clause at line 1086, but it is
independent of it (no braces before the "if" at line 1087).

This patch fixes the indentation to reflect the actual meaning of the code,
though is it actually meant to be part of the "else" clause?  (I'm a
compiler developer, not a kernel person).  It also adds spaces around
the assignment, to placate checkpatch.pl.

Seen via an experimental new gcc warning I'm working on for gcc 6,
-Wmisleading-indentation, using gcc r223098 adding
-Werror=misleading-indentation to KBUILD_CFLAGS in Makefile.
The experimental GCC emits this warning (as an error), rightly IMHO:

drivers/net/ethernet/dec/tulip/uli526x.c: In function â€˜uli526x_timer’:
drivers/net/ethernet/dec/tulip/uli526x.c:1118:3: error: statement is
indented as if it were guarded by... [-Werror=misleading-indentation]
   db->init=0;
    ^
drivers/net/ethernet/dec/tulip/uli526x.c:1086:4: note: ...this â€˜else’
clause, but it is not
  } else
     ^

Hope this is helpful
Dave

Signed-off-by: David Malcolm <dmalcolm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agonet: phy: dp83867: Add TI dp83867 phy
Dan Murphy [Tue, 2 Jun 2015 14:34:37 +0000 (09:34 -0500)]
net: phy: dp83867: Add TI dp83867 phy

Add support for the TI dp83867 Gigabit ethernet phy
device.

The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agoethernet: micrel: use time_after_eq
Antonio Murdaca [Tue, 2 Jun 2015 12:35:52 +0000 (14:35 +0200)]
ethernet: micrel: use time_after_eq

use the time_after_eq macro for jiffies comparison operation

Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agonet/mlx4_core: Fix build failure introduced by the EQ pool changes
Or Gerlitz [Tue, 2 Jun 2015 07:29:48 +0000 (10:29 +0300)]
net/mlx4_core: Fix build failure introduced by the EQ pool changes

When CONFIG_RFS_ACCEL or SMP aren't set, we fail to build, fix it.

Also, avoid build warning as of unused function on that setup.

Fixes: c66fa19c405a ('net/mlx4: Add EQ pool')
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agobatman-adv: Remove unnecessary ret variable in algo_register
Markus Pargmann [Fri, 26 Dec 2014 11:41:41 +0000 (12:41 +0100)]
batman-adv: Remove unnecessary ret variable in algo_register

Remove ret variable and all jumps.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: Remove unnecessary ret variable
Markus Pargmann [Fri, 26 Dec 2014 11:41:40 +0000 (12:41 +0100)]
batman-adv: Remove unnecessary ret variable

We can avoid this indirect return variable by directly returning the
error values.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: main, batadv_compare_eth return bool
Markus Pargmann [Fri, 26 Dec 2014 11:41:39 +0000 (12:41 +0100)]
batman-adv: main, batadv_compare_eth return bool

Declare the returntype of batadv_compare_eth as bool.
The function called inside this helper function
(ether_addr_equal_unaligned) also uses bool as return value, so there is
no need to return int.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: main, Convert is_my_mac() to bool
Markus Pargmann [Fri, 26 Dec 2014 11:41:38 +0000 (12:41 +0100)]
batman-adv: main, Convert is_my_mac() to bool

It is much clearer to see a bool type as return value than 'int' for
functions that are supposed to return true or false.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: Remove unnecessary check for orig_ifinfo not NULL
Sven Eckelmann [Sun, 1 Mar 2015 15:56:26 +0000 (16:56 +0100)]
batman-adv: Remove unnecessary check for orig_ifinfo not NULL

orig_ifinfo is dereferenced multiple times in batadv_iv_ogm_update_seqnos
before the check for NULL is done. The function also exists at the
beginning when orig_ifinfo would have been NULL. This makes the check at
the end unnecessary and only confuses the reader/code analyzers.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: types, Fix comment on bcast_own
Markus Pargmann [Fri, 26 Dec 2014 11:41:37 +0000 (12:41 +0100)]
batman-adv: types, Fix comment on bcast_own

batadv_orig_bat_iv->bcast_own is actually not a bitfield, it is an
array. Adjust the comment accordingly.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agoe1000e: Bump the version to 3.2.5
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:50 +0000 (17:05 +0300)]
e1000e: Bump the version to 3.2.5

Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: fix unit hang during loopback test
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:47 +0000 (17:05 +0300)]
e1000e: fix unit hang during loopback test

System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: fix systim issues
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:45 +0000 (17:05 +0300)]
e1000e: fix systim issues

Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: fix legacy interrupt handling in i219
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:42 +0000 (17:05 +0300)]
e1000e: fix legacy interrupt handling in i219

This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: fix flush_desc_ring implementation
Yanir Lubetkin [Tue, 2 Jun 2015 14:05:38 +0000 (17:05 +0300)]
e1000e: fix flush_desc_ring implementation

The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: fix logical error in flush_desc_rings
Yanir Lubetkin [Wed, 22 Apr 2015 16:25:17 +0000 (19:25 +0300)]
e1000e: fix logical error in flush_desc_rings

The condition under which the flush should occur was reversed.  The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.

If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: remove call to do_div and sign mismatch warning
Yanir Lubetkin [Wed, 22 Apr 2015 02:55:43 +0000 (05:55 +0300)]
e1000e: remove call to do_div and sign mismatch warning

Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: i219 execute unit hang fix on every reset or power state transition
Yanir Lubetkin [Wed, 22 Apr 2015 01:15:01 +0000 (04:15 +0300)]
e1000e: i219 execute unit hang fix on every reset or power state transition

After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoe1000e: i219 fix unit hang on reset and runtime D3
Yanir Lubetkin [Mon, 13 Apr 2015 23:20:21 +0000 (02:20 +0300)]
e1000e: i219 fix unit hang on reset and runtime D3

Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
9 years agoMerge tag 'iwlwifi-next-for-kalle-2015-06-03' of https://git.kernel.org/pub/scm/linux...
Kalle Valo [Wed, 3 Jun 2015 09:15:51 +0000 (12:15 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2015-06-03' of https://git./linux/kernel/git/iwlwifi/iwlwifi-next

* a few fixes (re-enablement of interrupts for certain new
  platforms that have special power states)
* Rework completely the RBD allocation model towards new
  multi RX hardware.
* cleanups
* scan reworks continuation (Luca)

9 years agobatman-adv: iv_ogm, fix comment function name
Markus Pargmann [Fri, 26 Dec 2014 11:41:36 +0000 (12:41 +0100)]
batman-adv: iv_ogm, fix comment function name

This is a small copy paste fix for batadv_ing_buffer_avg.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: iv_ogm, fix coding style
Markus Pargmann [Fri, 26 Dec 2014 11:41:35 +0000 (12:41 +0100)]
batman-adv: iv_ogm, fix coding style

The kernel coding style says, that there should not be multiple
assignments in one row.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: iv_ogm, Fix dup_status comment
Markus Pargmann [Fri, 26 Dec 2014 11:41:34 +0000 (12:41 +0100)]
batman-adv: iv_ogm, Fix dup_status comment

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: iv_ogm_orig_update, style, add missing brackets
Markus Pargmann [Fri, 26 Dec 2014 11:41:33 +0000 (12:41 +0100)]
batman-adv: iv_ogm_orig_update, style, add missing brackets

CodingStyle describes that either none or both branches of a conditional
have to have brackets.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: iv_ogm_queue_add, Simplify expressions
Markus Pargmann [Fri, 26 Dec 2014 11:41:32 +0000 (12:41 +0100)]
batman-adv: iv_ogm_queue_add, Simplify expressions

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agobatman-adv: iv_ogm_aggregate_new, simplify error handling
Markus Pargmann [Fri, 26 Dec 2014 11:41:31 +0000 (12:41 +0100)]
batman-adv: iv_ogm_aggregate_new, simplify error handling

It is just a bit easier to put the error handling at one place and let
multiple error paths use the same calls.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
9 years agoiwlwifi: mvm: advertise only HW-supported ciphers
Johannes Berg [Wed, 20 May 2015 14:51:28 +0000 (16:51 +0200)]
iwlwifi: mvm: advertise only HW-supported ciphers

After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.

To avoid breaking that feature, advertise only ciphers that the
hardware supports.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: bump the iwlmvm API number to 15
Emmanuel Grumbach [Wed, 3 Jun 2015 06:54:18 +0000 (09:54 +0300)]
iwlwifi: bump the iwlmvm API number to 15

The driver is now ready to handle the -15.ucode.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: Add DC2DC_CONFIG_CMD (0x83) cmd & TLV
Matti Gottlieb [Sun, 31 May 2015 06:18:30 +0000 (09:18 +0300)]
iwlwifi: mvm: Add DC2DC_CONFIG_CMD (0x83) cmd & TLV

Add DC2DC_CONFIG_CMD (0x83) cmd.

Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.

The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: Remove old scan commands
Matti Gottlieb [Sun, 31 May 2015 08:29:52 +0000 (11:29 +0300)]
iwlwifi: mvm: Remove old scan commands

The firmwares that used these commands is not supported
anymore. Remove them.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: prepare for higher API/CAPA bits
Johannes Berg [Mon, 1 Jun 2015 15:11:11 +0000 (17:11 +0200)]
iwlwifi: prepare for higher API/CAPA bits

Currently, loading the firmware fails when it has higher API or CAPA
bits than the driver supports. That's an issue with integration.

At the same time, actually using api[0] and capa[0] will become
confusing when we also have api[1] and capa[1], and it's almost
certain that we'll mix up the bits and use the bits for api[1] with
api[0] by accident.

Avoid all this by translating the API/CAPA bits to the regular kernel
test_bit() format, and also providing wrapper functions. Also use the
__bitwise__ facility of sparse to check that we're testing the right
one.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: simplify iwl_mvm_stop_roc()
Johannes Berg [Mon, 1 Jun 2015 21:38:23 +0000 (23:38 +0200)]
iwlwifi: mvm: simplify iwl_mvm_stop_roc()

As pointed out by smatch, there's no need for a loop that always
immediately terminates. Use an if statement instead and while at
it clean up the mvmvif initialization.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: dvm: enable IEEE80211_HW_SUPPORT_FAST_XMIT
Johannes Berg [Fri, 17 Apr 2015 13:50:43 +0000 (15:50 +0200)]
iwlwifi: dvm: enable IEEE80211_HW_SUPPORT_FAST_XMIT

Since the firmware is responsible for duration calculation, the
driver can easily support fast-xmit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: enable IEEE80211_HW_SUPPORT_FAST_XMIT
Johannes Berg [Fri, 17 Apr 2015 13:50:43 +0000 (15:50 +0200)]
iwlwifi: mvm: enable IEEE80211_HW_SUPPORT_FAST_XMIT

Since the firmware is responsible for duration calculation, the
driver can easily support fast-xmit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: pcie: New RBD allocation model
Sara Sharon [Tue, 28 Apr 2015 09:56:54 +0000 (12:56 +0300)]
iwlwifi: pcie: New RBD allocation model

As a preperation for multiple RX queues change the RBD
allocation model.

The new model includes a background allocator. The allocator is
called by the interrupt handler when there are two released
buffers by the queue, and the allocator starts allocating eight
pages per request.
When the queue has released 8 pages it tries claiming the
request. If the pages are not ready - it keeps claiming.
This new model should make sure that RBDs are always available
across the multiple queues.

The RBDs are transferred between the allocator and the queue.
The queue moves the free RBDs upon freeing them to the allocator.
The allocator moves them back to the queue's possession when the
request is claimed.
The allocator has an initial pool to make sure there are always RBDs
available for the request completion.
Release of the buffers at exit is done per pools - the allocator
frees its own initial pool and the queue frees its own pool.

Existing code refactor -
-Queue's initial pool is the size of the queue only as the allocation
of the new buffers no longer uses this pool.
-Removal of replenish background work, and replenish calls in the
interrupt handler and restock().
-The replenish() and the rxq used_list are used only during
initialization.
-Moved page allocation to a new function for code reuse.

New code -
Allocator code - new structure and functions.
Interrupt handler uses the allocator functions for replenishing buffers.
Reuse of the restock() method.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: pcie: re-enable interrupts on resume
Eliad Peller [Thu, 28 May 2015 13:50:12 +0000 (16:50 +0300)]
iwlwifi: pcie: re-enable interrupts on resume

On resume, all the interrupts are masked (CSR_INT_MASK is 0),
and ict is disabled.

Re-configure them both.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: don't use EBS for P2P find
David Spinadel [Tue, 26 May 2015 07:32:19 +0000 (10:32 +0300)]
iwlwifi: mvm: don't use EBS for P2P find

Don't use EBS for P2P find to make sure we find all GOs in
our only attempt.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: add inactive state to ebs status
David Spinadel [Wed, 20 May 2015 08:56:59 +0000 (11:56 +0300)]
iwlwifi: mvm: add inactive state to ebs status

Currently EBS status in scan complete notifications is set to
success if EBS wasn't activated. FW will add a special return
value for cases when EBS wasn't activated and we add a print
of this status.

This change is needed for debug only, no behavior changes.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: pcie: Control access to the NIC's PM registers via iwl_cfg
Avri Altman [Mon, 11 May 2015 08:04:34 +0000 (11:04 +0300)]
iwlwifi: pcie: Control access to the NIC's PM registers via iwl_cfg

Allow a cleaner way to access those hw-dependent registers,
instead of using the product family type etc.

Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: wrt: add mipi type to debug types
Liad Kaufman [Tue, 19 May 2015 10:47:03 +0000 (13:47 +0300)]
iwlwifi: wrt: add mipi type to debug types

This adds the MIPI mode type to the types declared supported
by the driver. Without this patch, when using MIPI mode and
looking at the logs the user would see the debug destination
"UNKNOWN".

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoiwlwifi: mvm: rs: pass rate directly to column checks
Eyal Shapira [Wed, 27 May 2015 19:00:03 +0000 (22:00 +0300)]
iwlwifi: mvm: rs: pass rate directly to column checks

A minor refactoring for following patches.
This enables the reuse of the checks functions.

type=cleanup

Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9 years agoray_cs: Change 1 to true for bool type variable.
Shailendra Verma [Wed, 27 May 2015 00:55:57 +0000 (06:25 +0530)]
ray_cs: Change 1 to true for bool type variable.

The variable translate is bool type. So assigning true instead of 1.

Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: device dump support via devcoredump framework
Amitkumar Karwar [Tue, 26 May 2015 13:34:32 +0000 (06:34 -0700)]
mwifiex: device dump support via devcoredump framework

Currently device dump generated in the driver is retrieved
using ethtool set/get dump commands. We will get rid of
ethtool approach and use devcoredump framework.

Device dump can be trigger by
cat /debugfs/mwifiex/mlanX/device_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcdX/data

We have prepared following script to split device dump data
into multiple files.

 [root]# cat mwifiex_split_dump_data.sh
 #!/bin/bash
 # usage: ./mwifiex_split_dump_data.sh dump_data

 fw_dump_data=$1

 mem_type="driverinfo ITCM DTCM SQRAM APU CIU ICU MAC"

 for name in ${mem_type[@]}
 do
     sed -n "/Start dump $name/,/End dump/p" $fw_dump_data  > tmp.$name.log
     if [ ! -s tmp.$name.log ]
     then
         rm -rf tmp.$name.log
     else
         #Remove the describle info "Start dump" and "End dump"
         sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
         if [ -s /data/$name.log ]
         then
             echo "generate /data/$name.log"
         else
             sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
             echo "generate /var/$name.log"
         fi
         rm -rf tmp.$name.log
     fi
 done

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: use generic name 'device dump'
Amitkumar Karwar [Tue, 26 May 2015 13:34:31 +0000 (06:34 -0700)]
mwifiex: use generic name 'device dump'

Currently we are dumping driver information also inside
firmware dump API. We will call it as device dump and
dump driver and firmware data separately.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: minor changes in debug messages
Amitkumar Karwar [Tue, 26 May 2015 13:34:30 +0000 (06:34 -0700)]
mwifiex: minor changes in debug messages

Small letters are used in debug messages to match coding style
at other places.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: dump driver information for PCIe interface
Amitkumar Karwar [Tue, 26 May 2015 13:34:29 +0000 (06:34 -0700)]
mwifiex: dump driver information for PCIe interface

Currently we are dumping driver information only for SDIO
interface. This patch adds missing mwifiex_dump_drv_info()
call for PCIe interface.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: fix a possible double free issue
Amitkumar Karwar [Tue, 26 May 2015 13:34:28 +0000 (06:34 -0700)]
mwifiex: fix a possible double free issue

As drv_info_dump pointer doesn't get reset, we may end up
freeing the allocated memory twice.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agomwifiex: fix SDIO firmware dump problem
Amitkumar Karwar [Tue, 26 May 2015 13:34:27 +0000 (06:34 -0700)]
mwifiex: fix SDIO firmware dump problem

It's been observed that firmware doesn't go back to normal
state when all firmware memories are dumped. As a result,
further commands are blocked. This happens due to missing
driver change of writing READ DONE to control register for
SDIO interface.

This patch adds a missing change to fix the problem.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9 years agoMerge branch 'sfc-next'
David S. Miller [Tue, 2 Jun 2015 19:57:39 +0000 (12:57 -0700)]
Merge branch 'sfc-next'

Shradha Shah says:

====================
sfc: ndo_get_phys_port_id, vadaptor stats and PF unload when Vf's assigned to guest

This is the third and last instalment of SRIOV for EF10 patches.

This patch set includes implementation of ndo_get_phys_port_id
and changes to the MAC statistics code in order to support
vadaptor statistics.

It also includes code to deal with PF unload when Vf's are still
assigned to the guest.

The first couple of patches create sysfs files for physical port
and link control flags which are particularly useful when we have
enabled a large number of VF's.

These patches have been tested with and without CONFIG_SFC_SRIOV.
The creation and content of the sysfs files has been tested.
The statistics are tested using ethtool for monitoring.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: leak vports if a VF is assigned during PF unload
Daniel Pieczko [Tue, 2 Jun 2015 10:41:00 +0000 (11:41 +0100)]
sfc: leak vports if a VF is assigned during PF unload

If any VF is assigned as the PF is unloaded, do not attempt to
remove its vport or the vswitch.  These will be removed if the
driver binds to the PF again, as an entity reset occurs during
probe.

A 'force' flag is added to efx_ef10_pci_sriov_disable() to
distinguish between disabling SR-IOV and driver unload.
SR-IOV cannot be disabled if VFs are assigned to guests.

If the PF driver is unloaded while VFs are assigned, the driver
may try to bind to the VF again at a later point if the driver
has been reloaded and the VF returns to the same domain as the PF.
In this case, the PF will not have a VF data structure, so the VF
can check this and drop out of probe early.

In this case, efx->vf_count will be zero but VFs will be present.
The user is advised to remove the VF and re-create it. The check
at the beginning of efx_ef10_pci_sriov_disable() that
efx->vf_count is non-zero is removed to allow SR-IOV to be
disabled in this case. Also, if the PF driver is unloaded, it
will disable SR-IOV to remove these unknown VFs.

By not disabling bus-mastering if VFs are still assigned, the VF
will continue to pass traffic after the PF has been removed.

When using the max_vfs module parameter, if VFs are already
present do not try to initialise any more.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: force removal of VF and vport on driver removal
Daniel Pieczko [Tue, 2 Jun 2015 10:40:46 +0000 (11:40 +0100)]
sfc: force removal of VF and vport on driver removal

When the driver unloads, force the unbind and removal of any
VFs in the host with the PF.  The PF cannot remove vports and
vswitches if they are still being used by a VF driver, and when
unloading the sfc driver the removal order is not guaranteed,
so the instruction from the PF to the VF to unbind enforces a
suitable ordering so that vswitches and vports can be removed.

As a result of this, manually unbinding the driver from a single
PF will result in all of its VFs in the host also being removed.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: do not allow VFs to be destroyed if assigned to guests
Daniel Pieczko [Tue, 2 Jun 2015 10:40:31 +0000 (11:40 +0100)]
sfc: do not allow VFs to be destroyed if assigned to guests

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: don't update stats on VF when called in atomic context
Daniel Pieczko [Tue, 2 Jun 2015 10:40:18 +0000 (11:40 +0100)]
sfc: don't update stats on VF when called in atomic context

The ifenslave command to set up a bond runs in an atomic
context, and it queries the stats on the devices that are
being enslaved. A VF needs to make an MCDI call to update
its stats, which is not allowed in atomic context.

The releasing of the stats_lock is moved to the beginning of
the VF stats update function so that in_interrupt() can be
used; it must be taken again before returning from this
function.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: suppress vadaptor stats when EVB is not present
Daniel Pieczko [Tue, 2 Jun 2015 10:40:05 +0000 (11:40 +0100)]
sfc: suppress vadaptor stats when EVB is not present

The raw_mask array is not initialised, so it needs to be
explicitly set to zero in the 'else' branch.

If the EVB capability is not present, a port cannot have multiple
functions so the per-port MAC stats are correct and should match
the corresponding vadaptor stats, so this redundancy can be
removed from the ethtool stats output.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: suppress ENOENT error messages from MC_CMD_MAC_STATS
Daniel Pieczko [Tue, 2 Jun 2015 10:39:49 +0000 (11:39 +0100)]
sfc: suppress ENOENT error messages from MC_CMD_MAC_STATS

MC_CMD_MAC_STATS can be called on a function before a
vadaptor has been created, as the kernel can call into this
through ndo_get_stats/ndo_get_stats64.

If MC_CMD_MAC_STATS is called before the DMA queues have been
setup, so that a vadaptor has not been created yet, firmware
will return ENOENT. This is expected, so suppress the MCDI
error message in this case.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: update netdevice statistics to use vadaptor stats
Daniel Pieczko [Tue, 2 Jun 2015 10:39:33 +0000 (11:39 +0100)]
sfc: update netdevice statistics to use vadaptor stats

The netdevice statistics (in /proc/net/dev) are per-function
stats so they must use the vadaptor stats. Change the use of
MAC stats to vadaptor stats, and remove any statistics that
can only be measured per-port.  All stats that are removed
will be shown as zeroes when these statistics are displayed.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: DMA the VF stats only when requested
Daniel Pieczko [Tue, 2 Jun 2015 10:39:20 +0000 (11:39 +0100)]
sfc: DMA the VF stats only when requested

Firmware does not support a periodic DMA of vadaptor-stats
on VFs, so only update the stats buffer when stats are
requested (when running "ethtool -S" or an ip/ifconfig
command that reports stats).

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: display vadaptor statistics for all interfaces
Daniel Pieczko [Tue, 2 Jun 2015 10:39:06 +0000 (11:39 +0100)]
sfc: display vadaptor statistics for all interfaces

All interfaces will display vadaptor statistics, so set all the
relevant bits in the stats bitmask. Only functions with the
LINKCTRL flag will see other stats, including (per-port) MAC stats.

The vadaptor stats are from rx_unicast to tx_overflow.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: set the port-id when calling MC_CMD_MAC_STATS
Daniel Pieczko [Tue, 2 Jun 2015 10:38:49 +0000 (11:38 +0100)]
sfc: set the port-id when calling MC_CMD_MAC_STATS

The port-id must be known so that the RMON level can be
set for the collection of vadapter stats.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: add "port_" prefix to MAC stats
Daniel Pieczko [Tue, 2 Jun 2015 10:38:34 +0000 (11:38 +0100)]
sfc: add "port_" prefix to MAC stats

The MAC stats are per-port and will only be displayed on the PF
with control of the link (one per physical port). Vadapter stats
will also be displayed for this PF, so distinguish the MAC stats
by adding a prefix of "port_".

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: Implement ndo_gets_phys_port_id() for EF10 VFs
Shradha Shah [Tue, 2 Jun 2015 10:38:16 +0000 (11:38 +0100)]
sfc: Implement ndo_gets_phys_port_id() for EF10 VFs

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: Add sysfs entry for flags (link control and primary)
Shradha Shah [Tue, 2 Jun 2015 10:37:58 +0000 (11:37 +0100)]
sfc: Add sysfs entry for flags (link control and primary)

On  every adapter there will be one primary PF per adaptor and
one link control PF per port.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
9 years agosfc: Add paranthesis correctly on all branches of the if statement
Shradha Shah [Tue, 2 Jun 2015 10:37:41 +0000 (11:37 +0100)]
sfc: Add paranthesis correctly on all branches of the if statement

This change is a stylistic change and does not affect
functionality.

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>