Peter Ujfalusi [Fri, 27 Mar 2015 11:35:53 +0000 (13:35 +0200)]
dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Fri, 27 Mar 2015 11:35:52 +0000 (13:35 +0200)]
dmaengine: omap-dma: Fix memory leak when terminating running transfer
In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Petr Kulhavy [Fri, 27 Mar 2015 11:35:51 +0000 (13:35 +0200)]
dmaengine: edma: fix memory leak when terminating running transfers
If edma_terminate_all() was called while a transfer was running (i.e. after
edma_execute() but before edma_callback()) the echan->edesc was not freed.
This was due to the fact that a running transfer is on none of the
vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute()
removes it from the desc_issued list), so the vchan_dma_desc_free_list()
called at the end of edma_terminate_all() didn't find it and didn't free it.
This bug was found on an AM1808 based hardware (very similar to da850evm,
however using the second MMC/SD controller), where intense operations on the SD
card wasted the device 128MB RAM within a couple of days.
Peter Ujfalusi:
The issue is even more severe since it affects cyclic (audio) transfers as
well. In this case starting/stopping audio will results memory leak.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Lars-Peter Clausen [Sat, 28 Mar 2015 17:05:44 +0000 (18:05 +0100)]
dmaengine: jz4740: Define capabilities
Setup the capabilities of the device/driver, so that users of the DMAengine API
can query them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Mon, 30 Mar 2015 16:14:41 +0000 (09:14 -0700)]
Merge tag 'gpio-v4.0-3' of git://git./linux/kernel/git/linusw/linux-gpio
Pull late GPIO fixes from Linus Walleij:
"Here are the (hopefully) last GPIO fixes for v4.0. Nothing
controversial whatsoever, just fixes:
- syscon GPIO fix for Keystone DSP GPIOs
- pin number translation fix for ACPI GPIO
- a smallish compiler warning fix on the mpc8xxx driver"
* tag 'gpio-v4.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: syscon: reduce message level when direction reg offset not in dt
gpiolib: translate pin number in GPIO ACPI callbacks
gpio: mpc8xxx: remove __initdata annotation for mpc8xxx_gpio_ids[]
Chris Wilson [Fri, 27 Mar 2015 11:02:10 +0000 (11:02 +0000)]
drm/i915: Skip allocating shadow batch for 0-length batches
Since
commit
17cabf571e50677d980e9ab2a43c5f11213003ae
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Jan 14 11:20:57 2015 +0000
drm/i915: Trim the command parser allocations
we may then try to allocate a zero-sized object and attempt to extract
its pages. Understandably this fails.
Note that the real offender seems to be
commit
b9ffd80ed659c559152c042e74741f4f60cac691
Author: Brad Volkin <bradley.d.volkin@intel.com>
Date: Thu Dec 11 12:13:10 2014 -0800
drm/i915: Use batch length instead of object size in command parser
Testcase: igt/gem_exec_nop #ivb,byt,hsw
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[cherry picked from commit
743e78c1d726d875b98ff9689cc77c4d3d5d9ae2
from drm-intel-next because 4.0 seems to be affected by this too,
despite that the obvious culprit is definitely not in 4.0. Whatever,
if fixes a bug.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Kalle Valo [Mon, 30 Mar 2015 06:39:12 +0000 (09:39 +0300)]
Merge tag 'iwlwifi-for-kalle-2015-03-30' of https://git./linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix a memory leak: we leaked memory each time the module
was loaded.
Dave Airlie [Mon, 30 Mar 2015 02:17:27 +0000 (12:17 +1000)]
Merge branch 'drm-fixes-4.0' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few more fixes for 4.0 for radeon. Sorry for the delay, I was
a little under the weather this week and time got away from me.
* 'drm-fixes-4.0' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: programm the VCE fw BAR as well
drm/radeon: always dump the ring content if it's available
radeon: Do not directly dereference pointers to BIOS area.
drm/radeon/dpm: fix 120hz handling harder
Linus Torvalds [Sun, 29 Mar 2015 22:26:31 +0000 (15:26 -0700)]
Linux 4.0-rc6
Linus Torvalds [Sun, 29 Mar 2015 22:09:31 +0000 (15:09 -0700)]
Merge tag 'armsoc-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The latest and greatest fixes for ARM platform code. Worth pointing
out are:
- Lines-wise, largest is a PXA fix for dealing with interrupts on DT
that was quite broken. It's still newish code so while we could
have held this off, it seemed appropriate to include now
- Some GPIO fixes for OMAP platforms added a few lines. This was
also fixes for code recently added (this release).
- Small OMAP timer fix to behave better with partially upstreamed
platforms, which is quite welcome.
- Allwinner fixes about operating point control, reducing
overclocking in some cases for better stability.
plus a handful of other smaller fixes across the map"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: juno: Fix misleading name of UART reference clock
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: socfpga: dts: fix spi1 interrupt
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
ARM: pxa: fix pxa interrupts handling in DT
ARM: pxa: Fix typo in zeus.c
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Olof Johansson [Sun, 29 Mar 2015 21:00:53 +0000 (14:00 -0700)]
Merge tag 'sunxi-fixes-for-4.0' of https://git./linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.0
There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.
* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 29 Mar 2015 20:58:54 +0000 (13:58 -0700)]
Merge tag 'fixes-v4.0-rc4' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for the -rc cycle:
- Fix a device tree based booting vs legacy booting regression for
omap3 crypto hardware by adding the missing DMA channels.
- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.
- Fix two timer issues that can cause hangs if the timer related
hwmod data is missing like it often initially is for new SoCs.
- Remove pcie hwmods entry from dts as that causes runtime PM to
fail for the PHYs.
- A paper bag type dts configuration fix for dm816x GPIO
interrupts that I just noticed. This is most of the changes
diffstat wise, but as it's a basic feature for connecting
devices and things work otherwise, it should be fixed.
* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 29 Mar 2015 20:58:04 +0000 (13:58 -0700)]
Merge tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next into fixes
Late fix for v4.0 on the SoCFPGA platform:
- Fix interrupt number for SPI1 interface
* tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: dts: fix spi1 interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Martin [Tue, 17 Mar 2015 12:35:41 +0000 (12:35 +0000)]
arm64: juno: Fix misleading name of UART reference clock
The UART reference clock speed is 7273.8 kHz, not 72738 kHz.
Dots aren't usually used in node names even though ePAPR permits
them. However, this can easily be avoided by expressing the
frequency in Hz, not kHz.
This patch changes the name to refclk7273800hz, reflecting the
actual clock speed.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 29 Mar 2015 20:47:21 +0000 (13:47 -0700)]
Merge tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux into fixes
arm: pxa: fixes for v4.0-rc5
There are only 2 fixes, one for the zeus board about the regulator changes,
where a typo prevented the zeus board from having a working can regulator,
and one regression triggered by the interrupts IRQ shift of 16 affecting all
boards.
* tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux:
ARM: pxa: fix pxa interrupts handling in DT
ARM: pxa: Fix typo in zeus.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Uwe Kleine-König [Fri, 27 Mar 2015 10:08:32 +0000 (11:08 +0100)]
net: fec: setup right value for mdio hold time
The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.
This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 27 Mar 2015 09:24:22 +0000 (12:24 +0300)]
net: tcp6: fix double call of tcp_v6_fill_cb()
tcp_v6_fill_cb() will be called twice if socket's state changes from
TCP_TIME_WAIT to TCP_LISTEN. That can result in control buffer data
corruption because in the second tcp_v6_fill_cb() call it's not copying
IP6CB(skb) anymore, but 'seq', 'end_seq', etc., so we can get weird and
unpredictable results. Performance loss of up to 1200% has been observed
in LTP/vxlan03 test.
This can be fixed by copying inet6_skb_parm to the beginning of 'cb'
only if xfrm6_policy_check() and tcp_v6_fill_cb() are going to be
called again.
Fixes: 2dc49d1680b53 ("tcp6: don't move IP6CB before xfrm6_policy_check()")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 27 Mar 2015 05:31:18 +0000 (11:01 +0530)]
cxgb4vf: Fix sparse warnings
Fixes sparse warnings introduced in commit
e85c9a7abfa407ed ("cxgb4/cxgb4vf: Add
code to calculate T5 BAR2 Offsets for SGE Queue Registers") and
df64e4d38c904dd3 ("cxgb4/cxgb4vf: Use new interfaces to calculate BAR2 SGE Queue
Register addresses") and few old ones
sparse warnings:
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: cast removes
>> address space of expression
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: incorrect type in
>> initializer (different address space)
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1020:40: sparse: incorrect type in
>> argument 1 (different base types)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 26 Mar 2015 16:56:38 +0000 (17:56 +0100)]
netns: don't clear nsid too early on removal
With the current code, ids are removed too early.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
- the bar nsid into the netns foo is removed
- the netns exit method of ipip is called, thus our ipip iface is removed:
=> a netlink message is sent in the netns foo to advertise this deletion
=> this netlink message requests an nsid for bar, thus a new nsid is
allocated for bar and never removed.
We must remove nsids when we are sure that nobody will refer to netns currently
cleaned.
Fixes: 0c7aecd4bde4 ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Cooper [Sun, 29 Mar 2015 19:34:05 +0000 (19:34 +0000)]
Merge branch 'irqchip/urgent-gic' into irqchip/urgent
Marc Zyngier [Fri, 27 Mar 2015 14:15:05 +0000 (14:15 +0000)]
irqchip: gicv3-its: Use non-cacheable accesses when no shareability
If the ITS or the redistributors report their shareability as zero,
then it is important to make sure they will no generate any cacheable
traffic, as this is unlikely to produce the expected result.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Marc Zyngier [Fri, 27 Mar 2015 14:15:04 +0000 (14:15 +0000)]
irqchip: gicv3-its: Fix PROP/PEND and BASE/CBASE confusion
The ITS driver sometime mixes up the use of GICR_PROPBASE bitfields
for the GICR_PENDBASE register, and GITS_BASER for GICR_CBASE.
This does not lead to any observable bug because similar bits are
at the same location, but this just make the code even harder to
understand...
This patch provides the required #defines and fixes the mixup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Andre Przywara [Fri, 27 Mar 2015 14:15:03 +0000 (14:15 +0000)]
irqchip: gicv3-its: Fix device ID encoding
When building ITS commands which have the device ID in it, we
should mask off the whole upper 32 bits of the first command word
before inserting the new value in there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Marc Zyngier [Fri, 27 Mar 2015 14:15:02 +0000 (14:15 +0000)]
irqchip: gicv3-its: Fix encoding of collection's target redistributor
With a monolithic GICv3, redistributors are addressed using a linear
number, while a distributed implementation uses physical addresses.
When encoding a target address into a command, we strip the lower
16 bits, as redistributors are always 64kB aligned. This works
perfectly well with a distributed implementation, but has the
silly effect of always encoding target 0 in the monolithic case
(unless you have more than 64k CPUs, of course).
The obvious fix is to shift the linear target number by 16 when
computing the target address, so that we don't loose any precious
bit.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
David S. Miller [Sun, 29 Mar 2015 19:24:46 +0000 (12:24 -0700)]
Merge branch 'cxgb4'
Hariprasad Shenai says:
====================
cxgb4: Fixes ingress queue mapping and other fixes
The below series fixes ingress queue mapping by allocating them dynamically to
prevent stack overflow. Disable napi and interrupts before unregistering netdev
to avoid crash while unloading driver when traffic is flowing.
The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Thu, 26 Mar 2015 04:34:26 +0000 (10:04 +0530)]
cxgb4: Disable interrupts and napi before unregistering netdev
Disable interrupts and quiesce rx before unregistering net device to avoid crash
while unloading driver when traffic is flowing through.
Based on original work by Shameem Khalid <shameem@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Thu, 26 Mar 2015 04:34:25 +0000 (10:04 +0530)]
cxgb4: Allocate dynamic mem. for egress and ingress queue maps
QIDs (egress/ingress) from firmware in FW_*_CMD.alloc command
can be anywhere in the range from EQ(IQFLINT)_START to EQ(IQFLINT)_END.
For eg, in the first load eqid can be from 100 to 300.
In the next load it can be from 301 to 500 (assume eq_start is 100 and eq_end is
1000).
The driver was assuming them to always start from EQ(IQFLINT)_START till
MAX_EGRQ(INGQ). This was causing stack overflow and subsequent crash.
Fixed it by dynamically allocating memory (of qsize (x_END - x_START + 1)) for
these structures.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Wed, 25 Mar 2015 21:45:03 +0000 (14:45 -0700)]
ipmr,ip6mr: call ip6mr_free_table() on failure path
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 25 Mar 2015 20:41:33 +0000 (21:41 +0100)]
usbnet: Fix tx_bytes statistic running backward in cdc_ncm
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3b4 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Ben Hutchings [Thu, 26 Feb 2015 19:34:37 +0000 (19:34 +0000)]
usbnet: Fix tx_packets stat for FLAG_MULTI_FRAME drivers
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 28 Mar 2015 18:25:04 +0000 (11:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix x86 syscall exit code bug that resulted in spurious non-execution
of TIF-driven user-return worklets, causing big trouble for things
like KVM that rely on user notifiers for correctness of their vcpu
model, causing crashes like double faults"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/entry: Check for syscall exit work with IRQs disabled
Linus Torvalds [Sat, 28 Mar 2015 18:21:23 +0000 (11:21 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Two clocksource driver fixes, and an idle loop RCU warning fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/sun5i: Fix cpufreq interaction with sched_clock()
clocksource/drivers: Fix various !CONFIG_HAS_IOMEM build errors
timers/tick/broadcast-hrtimer: Fix suspicious RCU usage in idle loop
Linus Torvalds [Sat, 28 Mar 2015 18:17:32 +0000 (11:17 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"A single sched/rt corner case fix for RLIMIT_RTIME correctness"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix RLIMIT_RTTIME when PI-boosting to RT
Linus Torvalds [Sat, 28 Mar 2015 18:12:08 +0000 (11:12 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
"A perf kernel side fix for a fuzzer triggered lockup"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix irq_work 'tail' recursion
Linus Torvalds [Sat, 28 Mar 2015 18:05:03 +0000 (11:05 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"A module unload lockdep race fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix the module unload key range freeing logic
Linus Torvalds [Sat, 28 Mar 2015 17:58:53 +0000 (10:58 -0700)]
Merge branch 'parisc-4.0-1' of git://git./linux/kernel/git/deller/parisc-linux
Pull parsic fixes from Helge Deller:
"One patch from Mikulas fixes a bug on parisc by artifically
incrementing the counter in pmd_free when the kernel tries to free
the preallocated pmd.
Other than that we now prevent that syscalls gets added without
incrementing __NR_Linux_syscalls and fix the initial pmd setup code
if a default page size greater than 4k has been selected"
* 'parisc-4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix pmd code to depend on PT_NLEVELS value, not on CONFIG_64BIT
parisc: mm: don't count preallocated pmds
parisc: Add compile-time check when adding new syscalls
Linus Torvalds [Sat, 28 Mar 2015 17:54:59 +0000 (10:54 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm ppc bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Fix instruction emulation
KVM: PPC: Book3S HV: Endian fix for accessing VPA yield count
KVM: PPC: Book3S HV: Fix spinlock/mutex ordering issue in kvmppc_set_lpcr()
Linus Torvalds [Sat, 28 Mar 2015 17:47:27 +0000 (09:47 -0800)]
Merge tag 'arc-4.0-fixes-part-2' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"We found some issues with signal handling taking down the system. I
know its late, but these are important and all marked for stable.
ARC signal handling related fixes uncovered during recent testing of
NPTL tools"
* tag 'arc-4.0-fixes-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: signal handling robustify
ARC: SA_SIGINFO ucontext regs off-by-one
Linus Torvalds [Sat, 28 Mar 2015 17:41:22 +0000 (10:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull selinux bugfix from James Morris.
Fix broken return value.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix sel_write_enforce broken return value
Darshana Padmadas [Sat, 28 Mar 2015 06:37:14 +0000 (12:07 +0530)]
iio: imu: Use iio_trigger_get for indio_dev->trig assignment
This patch uses iio_trigger_get to increment the reference
count of trigger device, to avoid incorrect assignment.
Can result in a null pointer dereference during removal if the
trigger has been changed before removal.
This patch refers to a similar situation encountered through the
following discussion:
http://www.spinics.net/lists/linux-iio/msg13669.html
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Stefan Agner [Tue, 24 Mar 2015 12:47:47 +0000 (13:47 +0100)]
iio: adc: vf610: use ADC clock within specification
Depending on conversion mode used, the ADC clock (ADCK) needs
to be below a maximum frequency. According to Vybrid's data
sheet this is 20MHz for the low power conversion mode.
The ADC clock is depending on input clock, which is the bus
clock by default. Vybrid SoC are typically clocked at at 400MHz
or 500MHz, which leads to 66MHz or 83MHz bus clock respectively.
Hence, a divider of 8 is required to stay below the specified
maximum clock of 20MHz.
Due to the different bus clock speeds, the resulting sampling
frequency is not static. Hence use the ADC clock and calculate
the actual available sampling frequency dynamically.
This fixes bogous values observed on some 500MHz clocked Vybrid
SoC. The resulting value usually showed Bit 9 being stuck at 1,
or 0, which lead to a value of +/-512.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Richard Weinberger [Mon, 16 Mar 2015 21:27:10 +0000 (22:27 +0100)]
iio/adc/cc10001_adc.c: Fix !HAS_IOMEM build
Fixes:
drivers/built-in.o: In function `cc10001_adc_probe':
cc10001_adc.c:(.text+0x412e92): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Benjamin Herrenschmidt [Mon, 23 Mar 2015 03:16:38 +0000 (14:16 +1100)]
drivers/of: Add empty ranges quirk for PA-Semi
The "sdc" node is missing the ranges property, it needs to be treated
as having an empty one otherwise translation fails for its children.
Fixes
746c9e9f92dd, "of/base: Fix PowerPC address parsing hack"
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Stable <stable@vger.kernel.org> # v3.18+
Linus Torvalds [Fri, 27 Mar 2015 21:45:42 +0000 (14:45 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- mtk_wdt: signedness bug in mtk_wdt_start()
- imgpdc: Fix NULL pointer dereference during probe and fix the default
heartbeat
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: imgpdc: Fix default heartbeat
watchdog: imgpdc: Fix probe NULL pointer dereference
watchdog: mtk_wdt: signedness bug in mtk_wdt_start()
Linus Torvalds [Fri, 27 Mar 2015 21:38:02 +0000 (14:38 -0700)]
Merge tag 'sound-4.0-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Three trivial oneliner fixes for HD-audio.
Two are device-specific quirks while one is a generic fix for recent
Realtek codecs"
* tag 'sound-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add one more node in the EAPD supporting candidate list
ALSA: hda_intel: apply the Seperate stream_tag for Sunrise Point
ALSA: hda - Add dock support for Thinkpad T450s (17aa:5036)
Martin K. Petersen [Fri, 27 Mar 2015 19:17:21 +0000 (15:17 -0400)]
libata: Blacklist queued TRIM on Samsung SSD 850 Pro
Blacklist queued TRIM on this drive for now.
Reported-by: Stefan Keller <linux-list@zahlenfresser.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CC: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Martin K. Petersen [Fri, 27 Mar 2015 19:17:20 +0000 (15:17 -0400)]
libata: Update Crucial/Micron blacklist
Micron has released an updated firmware (MU02) for M510/M550/MX100
drives to fix the issues with queued TRIM. Queued TRIM remains broken on
M500 but is working fine on later drives such as M600 and MX200.
Tweak our blacklist to reflect the above.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71371
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Christian König [Mon, 23 Mar 2015 10:33:00 +0000 (11:33 +0100)]
drm/radeon: programm the VCE fw BAR as well
Otherwise the VCE firmware needs to be in the first 256MB of VRAM.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 23 Mar 2015 10:32:59 +0000 (11:32 +0100)]
drm/radeon: always dump the ring content if it's available
Dumping is still possible if a ring isn't ready, only when it
isn't allocated at all we need to abort here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Miller [Thu, 19 Mar 2015 03:18:40 +0000 (23:18 -0400)]
radeon: Do not directly dereference pointers to BIOS area.
Use readb() and memcpy_fromio() accessors instead.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Wed, 18 Mar 2015 21:05:10 +0000 (17:05 -0400)]
drm/radeon/dpm: fix 120hz handling harder
Need to expand the check to handle short circuiting
if the selected state is the same as current state.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87796
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Jani Nikula [Thu, 26 Mar 2015 08:42:00 +0000 (10:42 +0200)]
drm/edid: set ELD for firmware and debugfs override EDIDs
If the user supplies EDID through firmware or debugfs override, the
driver callbacks are bypassed and the connector ELD does not get
updated, and audio fails. Set ELD for firmware and debugfs EDIDs too.
There should be no harm in gratuitously doing this for non HDMI/DP
connectors, as it's still up to the driver to use the ELD, if any.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82349
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=80691
Reported-by: Emil <emilsvennesson@gmail.com>
Reported-by: Rob Engle <grenoble@gmail.com>
Tested-by: Jolan Luff <jolan@gormsby.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Yan, Zheng [Fri, 27 Mar 2015 02:34:20 +0000 (10:34 +0800)]
locks: fix file_lock deletion inside loop
locks_delete_lock_ctx() is called inside the loop, so we
should use list_for_each_entry_safe.
Fixes: 8634b51f6ca2 (locks: convert lease handling to file_lock_context)
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Jean Delvare [Fri, 20 Mar 2015 08:59:47 +0000 (09:59 +0100)]
firmware: dmi_scan: Prevent dmi_num integer overflow
dmi_num is a u16, dmi_len is a u32, so this construct:
dmi_num = dmi_len / 4;
would result in an integer overflow for a DMI table larger than
256 kB. I've never see such a large table so far, but SMBIOS 3.0
makes it possible so maybe we'll see such tables in the future.
So instead of faking a structure count when the entry point does
not provide it, adjust the loop condition in dmi_table() to properly
deal with the case where dmi_num is not set.
This bug was introduced with the initial SMBIOS 3.0 support in commit
fc43026278b2 ("dmi: add support for SMBIOS 3.0 64-bit entry point").
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Grygorii Strashko [Tue, 24 Mar 2015 18:42:42 +0000 (20:42 +0200)]
gpio: syscon: reduce message level when direction reg offset not in dt
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@
02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@
2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit:
5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
James Morris [Fri, 27 Mar 2015 09:33:27 +0000 (20:33 +1100)]
Merge branch 'upstream' of git://git.infradead.org/users/pcmoore/selinux into for-linus
James Hogan [Fri, 20 Feb 2015 23:45:45 +0000 (23:45 +0000)]
watchdog: imgpdc: Fix default heartbeat
The IMG PDC watchdog driver heartbeat module parameter has no default so
it is initialised to zero. This results in the following warning during
probe:
imgpdc-wdt
2006000.wdt: Initial timeout out of range! setting max timeout
The module parameter description implies that the default value should
be PDC_WDT_DEF_TIMEOUT, which isn't yet used, so initialise it to that.
Also tweak the heartbeat module parameter description for consistency.
Fixes: 93937669e9b5 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
James Hogan [Fri, 20 Feb 2015 23:45:44 +0000 (23:45 +0000)]
watchdog: imgpdc: Fix probe NULL pointer dereference
The IMG PDC watchdog probe function calls pdc_wdt_stop() prior to
watchdog_set_drvdata(), causing a NULL pointer dereference when
pdc_wdt_stop() retrieves the struct pdc_wdt_dev pointer using
watchdog_get_drvdata() and reads the register base address through it.
Fix by moving the watchdog_set_drvdata() call earlier, to where various
other pdc_wdt->wdt_dev fields are initialised.
Fixes: 93937669e9b5 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Dan Carpenter [Wed, 11 Feb 2015 10:26:21 +0000 (13:26 +0300)]
watchdog: mtk_wdt: signedness bug in mtk_wdt_start()
"ret" should be signed for the error handling to work correctly. This
doesn't matter much in real life since mtk_wdt_set_timeout() always
succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Stefan Agner [Fri, 13 Mar 2015 13:51:51 +0000 (14:51 +0100)]
tty: serial: fsl_lpuart: clear receive flag on FIFO flush
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Agner [Fri, 13 Mar 2015 13:51:50 +0000 (14:51 +0100)]
tty: serial: fsl_lpuart: specify transmit FIFO size
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier Martinez Canillas [Fri, 13 Mar 2015 11:38:51 +0000 (12:38 +0100)]
serial: samsung: Clear operation mode on UART shutdown
Exynos serial ports operate either in a DMA-based or interrupt-based
modes. In DMA-based mode, the UART generates a transfer data request
and a Transmission (Tx) interrupt in interrupt-based mode.
The Tx IRQ is only unmasked in interrupt-based mode and it was done
in s3c24xx_serial_start_tx(). Commit
ba019a3e2ad5 ("serial: samsung:
remove redundant interrupt enabling") removed the IRQ enable on that
function since it is enabled when the mode is set in enable_tx_pio().
The problem is that enable_tx_pio() is only called if the port mode
has not been set before but the mode was not cleared on .shutdown().
So if the UART was shutdown and then started up again, the mode set
will remain and the Tx IRQ won't be unmasked.
This caused a hang on at least Exynos5250, Exynos5420 and Exynos5800
when the system is rebooted or powered off.
Fixes: ba019a3e2ad5 ("serial: samsung: remove redundant interrupt enabling")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 26 Mar 2015 22:10:27 +0000 (23:10 +0100)]
tty: clean up the tty time logic a bit
We only care if anything other than the lower 3 bits of the tty has
changed, so just check that way, which makes it a bit faster, and more
obvious what is going on. Also, document this for future developers to
understand why we did this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
Heikki Krogerus [Wed, 18 Mar 2015 10:55:13 +0000 (12:55 +0200)]
serial: 8250_dw: only get the clock rate in one place
The clock rate is requested from a property called
"clock-frequency" in both dw8250_probe_of and
dw8250_probe_acpi. Moving the requests to dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Wed, 18 Mar 2015 10:55:12 +0000 (12:55 +0200)]
serial: 8250_dw: remove useless ACPI ID check
Having ACPI handle does not mean the same as having ACPI
identifier. The check is in any case useless, but having it
prevents this driver from being used for example with
multifunctional PCI devices, such as the newer Intel LPSS
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 26 Mar 2015 22:04:05 +0000 (15:04 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm refcounting fixes from Dave Airlie:
"Here is the complete set of i915 bug/warn/refcounting fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Fixup legacy plane->crtc link for initial fb config
drm/i915: Fix atomic state when reusing the firmware fb
drm/i915: Keep ring->active_list and ring->requests_list consistent
drm/i915: Don't try to reference the fb in get_initial_plane_config()
drm: Fixup racy refcounting in plane_force_disable
Andy Shevchenko [Mon, 16 Mar 2015 08:53:58 +0000 (10:53 +0200)]
dmaengine: hsu: move memory allocation to GFP_NOWAIT
The GFP_ATOMIC is too strict, and DMAEngine documentation make an advice to use
GFP_NOWAIT. This patch does the conversion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Mon, 16 Mar 2015 08:53:57 +0000 (10:53 +0200)]
dmaengine: hsu: remove redundant pieces of code
There are few places where the implemented pieces of code are not needed, i.e.:
- direction can't be wrong in hsu_dma_chan_start()
- desc->active set to 0 by kzalloc
- DMAEngine is NULL-aware when call ->device_alloc_chan_resources()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Fri, 13 Mar 2015 15:44:26 +0000 (17:44 +0200)]
serial: 8250_pci: add Intel Tangier support
Intel Tangier contains 4 HSUART ports as found on Intel Edison board which are
8250 compatible. The patch adds necessary bits to the driver.
Note that the HSU port0 is currently unavailable and thus not supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Fri, 13 Mar 2015 15:44:25 +0000 (17:44 +0200)]
dmaengine: hsu: add Intel Tangier PCI ID
Intel Tangier is known to have the HSU DMA IP as PCI device 00:05.0. The patch
adds the ID as found on Intel Edison board to the PCI device table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Fri, 13 Mar 2015 16:51:13 +0000 (18:51 +0200)]
serial: 8250_pci: replace switch-case by formula for Intel MID
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
24 25 12
48000000 64000000 4000000(1)
49 50 14
49000000 56000000 3500000(1)
4 5 16
40000000 40000000 2500000(1)
16 25 16
32000000 32000000 500000(4),
1000000(2),
2000000(1)
24 25 16
48000000 48000000 1500000(2),
3000000(1)
2304 3125 16
36864000 36864000 576000(4),
1152000(2)
8192 15625 16
26214400 26214400 50(32768),200(8192)
9216 15625 16
29491200 29491200 1800(1024),57600(32),115200(16),
230400(8),460800(4),921600(2),
1843200(1)
12288 15625 16
39321600 39321600 75(32768),150(16384),300(8192),
600(4096),1200(2048),2400(1024),4800(512),
9600(256),19200(128),38400(64)
45056 78125 16
28835840 28835840 110(16384)
274432 390625 16
35127296 35127296 134(16384)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Fri, 13 Mar 2015 16:51:12 +0000 (18:51 +0200)]
serial: 8250_pci: replace switch-case by formula
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for byt_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) numerator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
4 5 16
80000000 80000000 2500000(2)
14 25 16
56000000 56000000 3500000(1)
16 25 16
64000000 64000000 500000(8),
1000000(4),
2000000(2),
4000000(1)
24 25 16
96000000 96000000 1500000(4),
3000000(2)
2180 3103 16
70254592 70254592 134(32768)
2304 3125 16
73728000 73728000 576000(8),
1152000(4)
8192 15625 16
52428800 52428800 50(65536),200(16384)
9216 15625 16
58982400 58982400 1800(2048),57600(64),115200(32),
230400(16),460800(8),921600(4),
1843200(2)
12288 15625 16
78643200 78643200 75(65536),150(32768),300(16384),
600(8192),1200(4096),2400(2048),
4800(1024),9600(512),19200(256),38400(128)
9893 17154 16
57671680 57671680 110(32768)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe Leroy [Thu, 12 Mar 2015 15:23:59 +0000 (16:23 +0100)]
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 17 Mar 2015 09:17:28 +0000 (12:17 +0300)]
serial: jsm: some off by one bugs
"brd->nasync" amd "brd->maxports" are the same. They hold the number of
filled out channels in the brd->channels[] array. These tests should
be ">=" instead of ">" so that we don't read one element past the end.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 11 Mar 2015 21:39:28 +0000 (22:39 +0100)]
serial: xuartps: Fix check in console_setup().
cdns_uart_console_setup() checks port->mapbase != 0, but the port may
not be initialized yet even if this condition is met [e.g., ioremap()
may have failed]. Check port->membase != NULL instead, similar to
cdns_early_console_setup().
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Thu, 12 Mar 2015 21:11:59 +0000 (22:11 +0100)]
serial: xuartps: Get rid of register access macros.
Get rid of cdns_uart_readl() and cdns_uart_writel() and just call
readl() and writel() directly.
Most of the patch was created by search-and-replace (I had to convert a
few lines manually, and break some lines longer than 80 columns):
* s/cdns_uart_readl(/readl(port->membase + /g
* s/cdns_uart_writel(\([^,]*\),/writel(\1, port->membase +/g
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 26 Mar 2015 21:53:47 +0000 (14:53 -0700)]
Merge tag 'dm-4.0-fix-2' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM core device cleanup regression -- due to a latent race that was
exposed by the bdi changes that were introduced during the 4.0 merge"
* tag 'dm-4.0-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix add_disk() NULL pointer due to race with free_dev()
Thomas Betker [Wed, 11 Mar 2015 21:39:27 +0000 (22:39 +0100)]
serial: xuartps: Fix iobase use.
cdns_uart_get_port() sets port->iobase = 1 to "mark port in use", but
this "in use" condition is not checked anywhere else in the code. So
remove the line, keeping port->iobase = 0 (which also makes more sense).
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 11 Mar 2015 21:39:26 +0000 (22:39 +0100)]
serial: xuartps: Fix cdns_uart_port[] definition.
The code assumes that the array cdns_uart_port[] has dimension
CDNS_UART_NR_PORTS, so let us define it this way.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Betker [Wed, 11 Mar 2015 21:39:25 +0000 (22:39 +0100)]
serial: xuartps: Fix register space size.
The register space size is 0x1000, and this value [not 0xfff] should be
provided to request_mem_region(), ioremap(), etc.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mans Rullgard [Sun, 8 Mar 2015 14:30:05 +0000 (14:30 +0000)]
serial: of: set port iomem size from devicetree
Make the 8250 driver reserve exactly the mmio region specified
in the devicetree. This prevents conflicts between UPIO_AU type
UARTs and other devices mapped closer than the default size of
0x1000 (or 0x100 for RT2880).
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mans Rullgard [Sun, 8 Mar 2015 14:30:04 +0000 (14:30 +0000)]
serial: 8250: allow specifying iomem size in addition to address
This adds a mapsize field to struct uart_port to be used in
conjunction with mapbase. If set, it overrides whatever value
serial8250_port_size() would otherwise report.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ken Xue [Mon, 9 Mar 2015 09:10:13 +0000 (17:10 +0800)]
serial: 8250_dw: add support for AMD SOC Carrizo
Add ACPI identifier for UART on AMD SOC Carrizo.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabian Frederick [Mon, 16 Mar 2015 19:17:11 +0000 (20:17 +0100)]
tty: constify of_device_id array
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabian Frederick [Mon, 16 Mar 2015 19:17:10 +0000 (20:17 +0100)]
tty/hvc_opal: constify of_device_id array
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 26 Mar 2015 21:43:42 +0000 (14:43 -0700)]
Merge tag 'linux-kselftest-4.0-rc6' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan.
* tag 'linux-kselftest-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix build failures when invoked from kselftest target
Nobuhiro Iwamatsu [Mon, 16 Mar 2015 16:19:54 +0000 (01:19 +0900)]
serial: sh-sci: Update calculation of timeout for DMA
The current calculation method in the case of 9600bps, rounding error occurs
has become setting that occur timeout faster than the required time. When we
use 9600bps, 32byte buffer, 10 bit (CS8) and 100 HZ, it becomes 3 jiffies
(30msec). In fact it is necessary 33msec. This updates to the calculation
that are not actually less than the value set by the rounding error.
Also, this is nothing will be calculated value when there is no load. If there
are a lot of case load, overrun error will occur immediately.
This is by the buffer size to be calculated twice the DMA buffer, and add the
change of setting a sufficient time-out value.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nobuhiro Iwamatsu [Mon, 16 Mar 2015 16:19:19 +0000 (01:19 +0900)]
serial: sh-sci: Add overrun handling of SCIFA and SCIFB
SCIFA and SCIFB can detect the overrun, but it does not support.
This adds overrun handling of SCIFA and SCIFB.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Airlie [Thu, 26 Mar 2015 21:39:45 +0000 (07:39 +1000)]
Merge tag 'drm-intel-fixes-2015-03-26' of git://anongit.freedesktop.org/drm-intel into drm-fixes
This should cover the final warnings in -rc5 with two more backports
from our development branch (drm-intel-next-queued). They're the ones
from Daniel and Damien, with references to the reports.
This is on top of drm-fixes because of the dependency on the two earlier
fixes not yet in Linus' tree.
There's an additional regression fix from Chris.
* tag 'drm-intel-fixes-2015-03-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fixup legacy plane->crtc link for initial fb config
drm/i915: Fix atomic state when reusing the firmware fb
drm/i915: Keep ring->active_list and ring->requests_list consistent
Jakub Kicinski [Mon, 16 Mar 2015 23:28:49 +0000 (00:28 +0100)]
sc16is7xx: enable the clock
Although clk_disable_unprepare() is called both on .remove()
and in .probe() error path, the clock is never actually enabled.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Mon, 16 Mar 2015 23:28:47 +0000 (00:28 +0100)]
sc16is7xx: don't wipe out port configuration on shutdown
EFCR register contains RS-485 configuration which should not
be changed by shutdown. Instead of doing a write only update
the appropriate bits.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Mon, 16 Mar 2015 23:28:46 +0000 (00:28 +0100)]
sc16is7xx: remove ports on probe error path
If ports are not explicitly removed on the error path
the device will not get properly unregistered leaving
/dev/ttySC* nodes in the filesystem.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doug Kehn [Tue, 24 Mar 2015 13:19:27 +0000 (08:19 -0500)]
tty/serial: omap: fix !wakeirq message
When wakeirq is not used/enabled, "no wakeirq for uart0" is output for
all TTY as the log message is generated before the port line is
initialized.
[ 0.802656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.811700] omap_uart
44e09000.serial: no wakeirq for uart0
[ 0.812379]
44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud =
3000000) is a OMAP UART0
[ 1.503622] console [ttyO0] enabled
[ 1.509836] omap_uart
48022000.serial: no wakeirq for uart0
[ 1.516118]
48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud =
3000000) is a OMAP UART1
[ 1.527711] omap_uart
48024000.serial: no wakeirq for uart0
[ 1.533881]
48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud =
3000000) is a OMAP UART2
[ 1.545324] omap_uart
481a6000.serial: no wakeirq for uart0
[ 1.551410]
481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud =
3000000) is a OMAP UART3
[ 1.562946] omap_uart
481a8000.serial: no wakeirq for uart0
[ 1.569036]
481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud =
3000000) is a OMAP UART4
Fix by moving wakeirq initialization, check, and dev_info() call to
after port line initialization and validation.
Signed-off-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd [Fri, 13 Mar 2015 18:09:36 +0000 (11:09 -0700)]
tty: serial: Remove orphaned serial driver
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd [Fri, 13 Mar 2015 18:09:37 +0000 (11:09 -0700)]
tty: serial: msm_serial: Remove dead code
This config no longer exists now that mach-msm has been removed.
Delete it and the associated code.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hung [Tue, 17 Mar 2015 10:02:14 +0000 (18:02 +0800)]
serial: 8250_pci: remove non-used var for F81504
Remove pci_fintek_setup() non-used var with calculation ciobase
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wang Long [Mon, 9 Mar 2015 04:17:51 +0000 (04:17 +0000)]
serial: 8250: remove the redundant include
The serial_core.h file have been included in header file
serial_8250.h. so remove the "#include <serial_core.h>" in
some 8250 serial drivers, because they have included the header file
serial_8250.h.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 9 Mar 2015 18:05:01 +0000 (14:05 -0400)]
serial: 8250: Check UART_SCR is writable
Au1x00/RT2800+ doesn't implement the 8250 scratch register (and
this may be true of other h/w currently supported by the 8250 driver);
read back the canary value written to the scratch register to enable
the console h/w restart after resume from system suspend.
Fixes: 4516d50aabedb ("serial: 8250: Use canary to restart console ...")
Reported-by: Mason <slash.tmp@free.fr>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 9 Mar 2015 18:05:00 +0000 (14:05 -0400)]
serial: 8250: Validate reg addr for Au1x00/RT288x i/o accessors
Au1x00/RT2800+ hardware has an alternate register layout which is
remapped with lookup tables by the au_serial_in()/out() i/o accessors.
However, the h/w does not support the complete 8250 register set, and
accesses to unmapped registers cause out-of-bounds lookups. Further,
because the lookup tables are defined by designated initializers, the
tables may contain unmapped entries (although the current tables do not).
Declare fixed-size lookup tables with contiguous initialization for
the complete 8250 register map; unmapped registers are initialized to -1.
Validate the register index (ie., 'offset') is in the range [0, table size).
Return fixed value for unmapped register reads and ignore unmapped register
writes.
Reported-by: Mason <slash.tmp@free.fr>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 26 Mar 2015 21:11:17 +0000 (14:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes for s390.
The ftrace comile fix is quite large for a -rc6 release, but it would
be nice to have it in 4.0"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/smp: reenable smt after resume
s390/mm: limit STACK_RND_MASK for compat tasks
s390/ftrace: fix compile error if CONFIG_KPROBES is disabled
s390/cpum_sf: add diagnostic sampling event only if it is authorized