Linus Torvalds [Tue, 14 Dec 2010 21:33:21 +0000 (13:33 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: tps6586x: correct register table
regulator: tps6586x: Handle both enable reg/bits being the same
regulator: tps6586x: Fix TPS6586X_DVM to store goreg/bit
regulator: tps6586x: Add missing bit mask generation
Linus Torvalds [Tue, 14 Dec 2010 21:32:40 +0000 (13:32 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Quirk for Dell Vostro 320 to make microphone work
ALSA: hda - Reset sample sizes and max bitrates when reading ELD
ALSA: hda - Always allow basic audio irrespective of ELD info
ALSA: hda - Do not wrongly restrict min_channels based on ELD
ASoC: Correct WM8962 interrupt mask register read
ASoC: WM8580: Debug BCLK and sample size
ASoC: Fix resource leak if soc_register_ac97_dai_link failed
ASoC: Hold client_mutex while calling snd_soc_instantiate_cards()
ASoC: Fix swap of left and right channels for WM8993/4 speaker boost gain
ASoC: Fix off by one error in WM8994 EQ register bank size
ALSA: hda: Use position_fix=1 for Acer Aspire 5538 to enable capture on internal mic
ALSA: hda - Enable jack sense for Thinkpad Edge 13
ALSA: hda - Fix ThinkPad T410[s] docking station line-out
ALSA: hda: Use model=lg quirk for LG P1 Express to enable playback and capture
Linus Torvalds [Tue, 14 Dec 2010 21:32:19 +0000 (13:32 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bp/bp
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Fix interleaving check
EDAC: Correct MiB_TO_PAGES() macro
EDAC: Fix workqueue-related crashes
Linus Torvalds [Tue, 14 Dec 2010 21:31:49 +0000 (13:31 -0800)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: don't apply 7xx HDP flush workaround on AGP
drm: use after free in drm_queue_vblank_event()
drm/kms: remove spaces from connector names (v2)
Linus Torvalds [Tue, 14 Dec 2010 21:31:23 +0000 (13:31 -0800)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (adm1026) Allow 1 as a valid divider value
hwmon: (adm1026) Fix setting fan_div
hwmon: (it87) Fix manual fan speed control on IT8721F
Theodore Ts'o [Tue, 14 Dec 2010 20:27:50 +0000 (15:27 -0500)]
ext4: Turn off multiple page-io submission by default
Jon Nelson has found a test case which causes postgresql to fail with
the error:
psql:t.sql:4: ERROR: invalid page header in block 38269 of relation base/16384/16581
Under memory pressure, it looks like part of a file can end up getting
replaced by zero's. Until we can figure out the cause, we'll roll
back the change and use block_write_full_page() instead of
ext4_bio_write_page(). The new, more efficient writing function can
be used via the mount option mblk_io_submit, so we can test and fix
the new page I/O code.
To reproduce the problem, install postgres 8.4 or 9.0, and pin enough
memory such that the system just at the end of triggering writeback
before running the following sql script:
begin;
create temporary table foo as select x as a, ARRAY[x] as b FROM
generate_series(1,
10000000 ) AS x;
create index foo_a_idx on foo (a);
create index foo_b_idx on foo USING GIN (b);
rollback;
If the temporary table is created on a hard drive partition which is
encrypted using dm_crypt, then under memory pressure, approximately
30-40% of the time, pgsql will issue the above failure.
This patch should fix this problem, and the problem will come back if
the file system is mounted with the mblk_io_submit mount option.
Reported-by: Jon Nelson <jnelson@jamponi.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Linus Torvalds [Tue, 14 Dec 2010 19:09:05 +0000 (11:09 -0800)]
Merge branch 'for-2.6.37' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.37' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix possible BUG_ON firing in set_change_info
sunrpc: prevent use-after-free on clearing XPT_BUSY
Linus Torvalds [Tue, 14 Dec 2010 19:08:13 +0000 (11:08 -0800)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: prevent RAID level downgrades when space is low
Btrfs: account for missing devices in RAID allocation profiles
Btrfs: EIO when we fail to read tree roots
Btrfs: fix compiler warnings
Btrfs: Make async snapshot ioctl more generic
Btrfs: pwrite blocked when writing from the mmaped buffer of the same page
Btrfs: Fix a crash when mounting a subvolume
Btrfs: fix sync subvol/snapshot creation
Btrfs: Fix page leak in compressed writeback path
Btrfs: do not BUG if we fail to remove the orphan item for dead snapshots
Btrfs: fixup return code for btrfs_del_orphan_item
Btrfs: do not do fast caching if we are allocating blocks for tree_root
Btrfs: deal with space cache errors better
Btrfs: fix use after free in O_DIRECT
Linus Torvalds [Tue, 14 Dec 2010 19:07:39 +0000 (11:07 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: verify ioctl retries
fuse: fix ioctl when server is 32bit
Linus Torvalds [Tue, 14 Dec 2010 19:06:17 +0000 (11:06 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: log timestamp changes to the source inode in rename
Linus Torvalds [Tue, 14 Dec 2010 19:02:15 +0000 (11:02 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix ioctl magic
ceph: Behave better when handling file lock replies.
ceph: pass lock information by struct file_lock instead of as individual params.
ceph: Handle file locks in replies from the MDS.
ceph: avoid possible null deref in readdir after dir llseek
Linus Torvalds [Tue, 14 Dec 2010 16:51:12 +0000 (08:51 -0800)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix panic after nfs_umount()
nfs: remove extraneous and problematic calls to nfs_clear_request
nfs: kernel should return EPROTONOSUPPORT when not support NFSv4
NFS: Fix fcntl F_GETLK not reporting some conflicts
nfs: Discard ACL cache on mode update
NFS: Readdir cleanups
NFS: nfs_readdir_search_for_cookie() don't mark as eof if cookie not found
NFS: Fix a memory leak in nfs_readdir
Call the filesystem back whenever a page is removed from the page cache
NFS: Ensure we use the correct cookie in nfs_readdir_xdr_filler
Linus Torvalds [Tue, 14 Dec 2010 16:49:15 +0000 (08:49 -0800)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: remove bogus remapping of error in cifs_filldir()
cifs: allow calling cifs_build_path_to_root on incomplete cifs_sb
cifs: fix check of error return from is_path_accessable
cifs: remove Local_System_Name
cifs: fix use of CONFIG_CIFS_ACL
cifs: add attribute cache timeout (actimeo) tunable
Steven Rostedt [Sat, 4 Dec 2010 04:12:33 +0000 (23:12 -0500)]
workqueue: It is likely that WORKER_NOT_RUNNING is true
Running the annotate branch profiler on three boxes, including my
main box that runs firefox, evolution, xchat, and is part of the distcc farm,
showed this with the likelys in the workqueue code:
correct incorrect % Function File Line
------- --------- - -------- ---- ----
96 996253 99 wq_worker_sleeping workqueue.c 703
96 996247 99 wq_worker_waking_up workqueue.c 677
The likely()s in this case were assuming that WORKER_NOT_RUNNING will
most likely be false. But this is not the case. The reason is
(and shown by adding trace_printks and testing it) that most of the time
WORKER_PREP is set.
In worker_thread() we have:
worker_clr_flags(worker, WORKER_PREP);
[ do work stuff ]
worker_set_flags(worker, WORKER_PREP, false);
(that 'false' means not to wake up an idle worker)
The wq_worker_sleeping() is called from schedule when a worker thread
is putting itself to sleep. Which happens most of the time outside
of that [ do work stuff ].
The wq_worker_waking_up is called by the wakeup worker code, which
is also callod outside that [ do work stuff ].
Thus, the likely and unlikely used by those two functions are actually
backwards.
Remove the annotation and let gcc figure it out.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Fri, 10 Dec 2010 16:20:23 +0000 (17:20 +0100)]
MAINTAINERS: Add workqueue entry
Signed-off-by: Tejun Heo <tj@kernel.org>
Andrew Kephart [Mon, 13 Dec 2010 15:46:34 +0000 (09:46 -0600)]
fbdev: Fix fb_find_nearest_mode refresh comparison
Refresh rate nearness is not calculated or reset when nearest resolution
changes.
This patch resets the refresh rate differential measurement whenever a
new nearest resolution is discovered. This fixes two error cases;
first, wherein the first mode's refresh rate differential is never
calculated and second, when the closest refresh rate from a previous
nearest resolution is erroneously preserved.
Signed-off-by: Andrew Kephart <andrew.kephart@alereon.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Carmelo AMOROSO [Mon, 13 Dec 2010 10:20:26 +0000 (10:20 +0000)]
sh: wire up accept4 syscall (non-multiplexed path)
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nicolas Ferre [Mon, 13 Dec 2010 12:48:41 +0000 (13:48 +0100)]
dmaengine: at_hdmac: fix buffer transfer size specification
Buffer transfer size is the number of transfers to be performed in
relation with the width of the _source_ interface.
So in the DMA_FROM_DEVICE case, it should be the register width that
should be taken into account.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jason Wessel [Wed, 1 Dec 2010 19:01:01 +0000 (13:01 -0600)]
kgdboc,input: Fix regression with keyboard release key and early debugging
The commit
111c182340cd22e238ab1cc6564df336c6ebd7cb (kgdboc: reset
input devices (keyboards) when exiting debugger) introduced a
regression in early debugging such that you get a kernel oops on
continue (with the go command) if you boot a kernel with:
earlyprintk=vga ekgdboc=kbd kgdbwait
The restore kgdboc_restore_input() routine schedules work for the
purpose of sending key release events for any keys that were in the
depressed state prior to entering the kernel debugger. A simple fix
to the crash is to not invoke the schedule_work() if the kernel
system_state is anything other than SYSTEM_RUNNING.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Len Brown [Tue, 14 Dec 2010 03:40:54 +0000 (22:40 -0500)]
Merge branch 'bugzilla-23002' into release
Rafael J. Wysocki [Sun, 12 Dec 2010 20:10:42 +0000 (21:10 +0100)]
ACPI / PM: Do not save/restore NVS on Sony Vaio VGN-NW130D
The saving of the NVS memory area during suspend and restoring it
during resume causes problems to appear on Sony Vaio VGN-NW130D, so
blacklist that machine to avoid those problems.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=23002
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Adriano <adriano.vilela@yahoo.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Chris Mason [Mon, 13 Dec 2010 20:06:46 +0000 (15:06 -0500)]
Btrfs: prevent RAID level downgrades when space is low
The extent allocator has code that allows us to fill
allocations from any available block group, even if it doesn't
match the raid level we've requested.
This was put in because adding a new drive to a filesystem
made with the default mkfs options actually upgrades the metadata from
single spindle dup to full RAID1.
But, the code also allows us to allocate from a raid0 chunk when we
really want a raid1 or raid10 chunk. This can cause big trouble because
mkfs creates a small (4MB) raid0 chunk for data and metadata which then
goes unused for raid1/raid10 installs.
The allocator will happily wander in and allocate from that chunk when
things get tight, which is not correct.
The fix here is to make sure that we provide duplication when the
caller has asked for it. It does all the dups to be any raid level,
which preserves the dup->raid1 upgrade abilities.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Mon, 13 Dec 2010 19:56:23 +0000 (14:56 -0500)]
Btrfs: account for missing devices in RAID allocation profiles
When we mount in RAID degraded mode without adding a new device to
replace the failed one, we can end up using the wrong RAID flags for
allocations.
This results in strange combinations of block groups (raid1 in a raid10
filesystem) and corruptions when we try to allocate blocks from single
spindle chunks on drives that are actually missing.
The first device has two small 4MB chunks in it that mkfs creates and
these are usually unused in a raid1 or raid10 setup. But, in -o degraded,
the allocator will fall back to these because the mask of desired raid groups
isn't correct.
The fix here is to count the missing devices as we build up the list
of devices in the system. This count is used when picking the
raid level to make sure we continue using the same levels that were
in place before we lost a drive.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Forrest Shi [Thu, 9 Dec 2010 08:14:04 +0000 (16:14 +0800)]
fsldma: fix issue of slow dma
Fixed fsl dma slow issue by initializing dma mode register with
bandwidth control. It boosts dma performance and should works
with 85xx board.
Signed-off-by: Forrest Shi <b29237@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Chris Mason [Mon, 13 Dec 2010 19:47:58 +0000 (14:47 -0500)]
Btrfs: EIO when we fail to read tree roots
If we just get a plain IO error when we read tree roots, the code
wasn't properly sending that error up the chain. This allowed mounts to
continue when they should failed, and allowed operations
on partially setup root structs. The end result was usually oopsen
on spinlocks that hadn't been spun up correctly.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Ira W. Snyder [Mon, 13 Dec 2010 16:42:30 +0000 (11:42 -0500)]
hwmon: (ltc4215) make sysfs file match the alarm cause
The ltc4215 driver used the chip's "power good" status bit to provide
the power1_alarm file. This is wrong: the chip is really reporting the
status of one of the monitored voltages.
Change the sysfs file from power1_alarm to in2_min_alarm instead. This
matches the voltage that the chip is raising an alarm for.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Paul Mundt [Mon, 13 Dec 2010 05:59:51 +0000 (14:59 +0900)]
sh: Enable deprecated IRQ chip APIs for MFD and GPIOLIB drivers.
There are still quite a number of MFD and GPIO expander drivers that are
using the old irq_chip APIs that haven't had a chance to update during
the .37 cycle, resulting in allyes/modconfig errors on some
configurations.
Mark Brown has done most of the legwork to get these fixed up in .38,
so this should just be a .37 stop-gap that we can drop at the end of the
.38 merge window.
Reported-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Russell King [Sun, 12 Dec 2010 23:45:39 +0000 (23:45 +0000)]
Merge branch 'fix' of git://git./linux/kernel/git/ycmiao/pxa-linux-2.6
Russell King [Sun, 12 Dec 2010 23:24:28 +0000 (23:24 +0000)]
ARM: Update mach-types
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Tue, 7 Dec 2010 15:56:29 +0000 (16:56 +0100)]
ARM: 6528/1: Use CTR for the I-cache line size on ARMv7
The current implementation of the v7_coherent_*_range function assumes
that the D and I cache lines have the same size, which is incorrect
architecturally. This patch adds the icache_line_size macro which reads
the CTR register. The main loop in v7_coherent_*_range is split in two
independent loops or the D and I caches. This also has the performance
advantage that the DSB is moved outside the main loop.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Tue, 7 Dec 2010 15:52:04 +0000 (16:52 +0100)]
ARM: 6527/1: Use CTR instead of CCSIDR for the D-cache line size on ARMv7
The current implementation of the dcache_line_size macro reads the L1
cache size from the CCSIDR register. This, however, is not guaranteed to
be the smallest cache line in the cache hierarchy. The patch changes to
the macro to use the more architecturally correct CTR register.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrej Ota [Sun, 12 Dec 2010 23:06:16 +0000 (15:06 -0800)]
pppoe.c: Fix kernel panic caused by __pppoe_xmit
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
This fixes commit
55c95e738da85373965cb03b4f975d0fd559865b.
Reported-by: Gorik Van Steenberge <gvs@zemos.net>
Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Reported-by: Pawel Staszewski <pstaszewski@artcom.pl>
Diagnosed-by: Andrej Ota <andrej@ota.si>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Tested-by: Pawel Staszewski <pstaszewski@artcom.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrej Ota <andrej@ota.si>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Halasa [Sun, 12 Dec 2010 12:06:47 +0000 (12:06 +0000)]
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
We must not wake the TX queue without free TX descriptors.
sca_xmit() expects at least one free descriptor and BUGs otherwise.
Problem reported and fix tested by Bernie Innocenti and Ward Vandewege.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Zolotarov [Sun, 12 Dec 2010 04:12:29 +0000 (04:12 +0000)]
bnx2x: Advance a version number to 1.60.01-0
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Zolotarov [Sun, 12 Dec 2010 04:12:12 +0000 (04:12 +0000)]
bnx2x: Fixed a compilation warning
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Zolotarov [Sun, 12 Dec 2010 04:11:45 +0000 (04:11 +0000)]
bnx2x: LSO code was broken on BE platforms
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Sat, 11 Dec 2010 11:06:50 +0000 (11:06 +0000)]
qlge: Fix deadlock when cancelling worker.
Removing usage of rtnl_lock() to protect firmware interface registers.
These registers are accessed in some worker threads and can create a
deadlock if rtnl_lock is taken by upper layers while the worker is still
pending.
We remove rtnl_lock and use a driver mutex just while mailboxes are
accessed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 12 Dec 2010 22:16:51 +0000 (14:16 -0800)]
Merge branch 'vhost-net' of git://git./linux/kernel/git/mst/vhost
Stefan Richter [Tue, 7 Dec 2010 19:32:40 +0000 (20:32 +0100)]
firewire: ohci: fix regression with Agere FW643 rev 06, disable MSI
Agere FW643 rev 06, listed as "11c1:5901 (rev 06) (prog-if 10 [OHCI])",
produced SBP-2 I/O errors since kernel 2.6.36. Disabling MSI fixes it.
Since MSI work on Agere FW643-E (same vendor and device ID, but rev 07),
introduce a device revision field into firewire-ohci's quirks list so
that different quirks can be defined for older and newer revisions.
Reported-by: Jonathan Isom <jeisom@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y
Stefan Richter [Tue, 7 Dec 2010 18:16:02 +0000 (19:16 +0100)]
firewire: ohci: fix regression with VIA VT6315, disable MSI
"VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]"
does not generate any interrupts if Message Signaled Interrupts were
enabled. This is a regression since kernel 2.6.36 in which MSI support
was added to firewire-ohci. Hence blacklist MSI on all VIA controllers.
Reported-by: Robin Cook <rcook@wyrms.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.36.y
Kevin Granade [Sat, 11 Dec 2010 07:04:02 +0000 (23:04 -0800)]
Input: wacom - add another Bamboo Pen ID (0xd4)
Add the features struct and device table entry to enable yet another
version of Wacom Bamboo Pen (CTL460, Product ID 0xD4).
Signed-off-by: Kevin Granade <kevin.granade@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Len Brown [Sat, 11 Dec 2010 07:02:02 +0000 (02:02 -0500)]
Merge branches 'bugzilla-15418', 'bugzilla-21722', 'bugzilla-22932', 'misc-2.6.37' and 'osi-regression' into release
Jan Beulich [Tue, 7 Dec 2010 14:58:44 +0000 (14:58 +0000)]
ACPI/HEST: adjust section selection
Properly const-, __init-, and __read_mostly-annotate this code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Jan Beulich [Tue, 7 Dec 2010 14:52:25 +0000 (14:52 +0000)]
ACPI: eliminate unused variable warning for !ACPI_SLEEP
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Jan Beulich [Tue, 7 Dec 2010 15:05:49 +0000 (15:05 +0000)]
ACPI/PNP: avoid section mismatch warning
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 8 Dec 2010 02:40:26 +0000 (10:40 +0800)]
ACPI thermal: remove two unused functions
When CONFIG_CPU_FREQ=n ...
drivers/acpi/processor_thermal.c:159:12: warning: ‘acpi_thermal_cpufreq_increase’ defined but not used
drivers/acpi/processor_thermal.c:163:12: warning: ‘acpi_thermal_cpufreq_decrease’ defined but not used
Remove unused declaration of ‘acpi_thermal_cpufreq_increase’ and
‘acpi_thermal_cpufreq_decrease’
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 8 Dec 2010 02:40:36 +0000 (10:40 +0800)]
ACPI: fix a section mismatch
WARNING: drivers/acpi/acpi.o(.text+0xeda): Section mismatch in reference from the function acpi_os_initialize1() to the function .init.text:set_osi_linux()
The function acpi_os_initialize1() references
the function __init set_osi_linux().
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Huang Ying [Thu, 2 Dec 2010 02:40:53 +0000 (10:40 +0800)]
ACPI, APEI, use raw spinlock in ERST
ERST writing may be used in NMI or Machine Check Exception handler. So
it need to use raw spinlock instead of normal spinlock. This patch
fixes it.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Chris Wilson [Sun, 5 Sep 2010 13:51:49 +0000 (14:51 +0100)]
ACPI: video: fix build for CONFIG_ACPI=n
In file included from drivers/gpu/drm/i915/intel_opregion.c:30:
include/acpi/video.h:22: warning: ‘struct acpi_device’ declared inside parameter list
...
include/acpi/video.h:24: error: ‘ENODEV’ undeclared (first use in this function)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Tue, 30 Nov 2010 23:21:46 +0000 (18:21 -0500)]
ACPI: video: fix build for VIDEO_OUTPUT_CONTROL=n
drivers/built-in.o: In function `acpi_video_bus_put_devices':
video.c:(.text+0x79663): undefined reference to
`video_output_unregister'
drivers/built-in.o: In function `acpi_video_bus_add':
video.c:(.text+0x7b0b3): undefined reference to `video_output_register'
Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 9 Dec 2010 08:51:06 +0000 (16:51 +0800)]
ACPI: fix allowing to add/remove multiple _OSI strings
commit
b0ed7a91(ACPICA/ACPI: Add new host interfaces for _OSI suppor)
introduced another regression that only one _OSI string can be added or
removed.
Now multiple _OSI strings can be added or removed, for example
acpi_osi=Linux acpi_osi=FreeBSD acpi_osi="!Windows 2006"
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming [Thu, 9 Dec 2010 08:50:52 +0000 (16:50 +0800)]
acpi: fix _OSI string setup regression
commit
b0ed7a91(ACPICA/ACPI: Add new host interfaces for _OSI suppor)
introduced a regression that _OSI string setup fails.
There are 2 paths to setup _OSI string.
DMI:
acpi_dmi_osi_linux -> set_osi_linux -> acpi_osi_setup -> copy _OSI
string to osi_setup_string
Boot command line:
acpi_osi_setup -> copy _OSI string to osi_setup_string
Later, acpi_osi_setup_late will be called to handle osi_setup_string.
If _OSI string is "Linux" or "!Linux", then the call path is,
acpi_osi_setup_late -> acpi_cmdline_osi_linux -> set_osi_linux ->
acpi_osi_setup -> copy _OSI string to osi_setup_string
This actually never installs _OSI string(acpi_install_interface not
called), but just copy the _OSI string to osi_setup_string.
This patch fixes the regression.
Reported-and-tested-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Paul Walmsley [Mon, 6 Dec 2010 20:52:40 +0000 (20:52 +0000)]
OMAP2: PRCM: fix some SHIFT macros that were actually bitmasks
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eric Dumazet [Sun, 5 Dec 2010 18:50:32 +0000 (18:50 +0000)]
net: fix skb_defer_rx_timestamp()
After commit
c1f19b51d1d8 (net: support time stamping in phy devices.),
kernel might crash if CONFIG_NETWORK_PHY_TIMESTAMPING=y and
skb_defer_rx_timestamp() handles a packet without an ethernet header.
Fixes kernel bugzilla #24102
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=24102
Reported-and-tested-by: Andrew Watts <akwatts@ymail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casey Leedom [Thu, 9 Dec 2010 09:38:24 +0000 (09:38 +0000)]
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
Was using L1_CACHE_BYTES for the Ingress Queue Entry Size but it really
needs to be 64 bytes in order to support the largest message sizes.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Wed, 8 Dec 2010 23:05:13 +0000 (23:05 +0000)]
phy: add the IC+ IP1001 driver
This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Wed, 8 Dec 2010 19:40:47 +0000 (19:40 +0000)]
atm: correct sysfs 'device' link creation and parent relationships
The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kyle McMartin [Thu, 9 Dec 2010 09:50:08 +0000 (09:50 +0000)]
MAINTAINERS: remove me from tulip
It was a nice idea, but -ENOTIME and -ENOHW. I never got around to doing
a lot of the clean up that I intended to.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 7 Dec 2010 17:11:09 +0000 (17:11 +0000)]
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
SCTP_SET_PEER_PRIMARY_ADDR does not accpet v4mapped address, using
v4mapped address in SCTP_SET_PEER_PRIMARY_ADDR socket option will
get -EADDRNOTAVAIL error if v4map is enabled. This patch try to
fix it by mapping v4mapped address to v4 address if allowed.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Wed, 8 Dec 2010 13:05:45 +0000 (13:05 +0000)]
enic: Bug Fix: Pass napi reference to the isr that services receive queue
Pass reference to napi instead of enic device to the isr that services receive queue.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Beulich [Tue, 7 Dec 2010 14:54:09 +0000 (14:54 +0000)]
Btrfs: fix compiler warnings
... regarding an unused function when !MIGRATION, and regarding a
printk() format string vs argument mismatch.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Li Zefan [Fri, 10 Dec 2010 06:41:56 +0000 (06:41 +0000)]
Btrfs: Make async snapshot ioctl more generic
If we had reserved some bytes in struct btrfs_ioctl_vol_args, we
wouldn't have to create a new structure for async snapshot creation.
Here we convert async snapshot ioctl to use a more generic ABI, as
we'll add more ioctls for snapshots/subvolumes in the future, readonly
snapshots for example.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Xin Zhong [Thu, 9 Dec 2010 09:30:14 +0000 (09:30 +0000)]
Btrfs: pwrite blocked when writing from the mmaped buffer of the same page
This problem is found in meego testing:
http://bugs.meego.com/show_bug.cgi?id=6672
A file in btrfs is mmaped and the mmaped buffer is passed to pwrite to write to the same page
of the same file. In btrfs_file_aio_write(), the pages is locked by prepare_pages(). So when
btrfs_copy_from_user() is called, page fault happens and the same page needs to be locked again
in filemap_fault(). The fix is to move iov_iter_fault_in_readable() before prepage_pages() to make page
fault happen before pages are locked. And also disable page fault in critical region in
btrfs_copy_from_user().
Reviewed-by: Yan, Zheng<zheng.z.yan@intel.com>
Signed-off-by: Zhong, Xin <xin.zhong@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Li Zefan [Tue, 7 Dec 2010 01:51:26 +0000 (01:51 +0000)]
Btrfs: Fix a crash when mounting a subvolume
We should drop dentry before deactivating the superblock, otherwise
we can hit this bug:
BUG: Dentry
f349a690{i=100,n=/} still in use (1) [unmount of btrfs loop1]
...
Steps to reproduce the bug:
# mount /dev/loop1 /mnt
# mkdir save
# btrfs subvolume snapshot /mnt save/snap1
# umount /mnt
# mount -o subvol=save/snap1 /dev/loop1 /mnt
(crash)
Reported-by: Michael Niederle <mniederle@gmx.at>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Sage Weil [Fri, 10 Dec 2010 00:36:28 +0000 (00:36 +0000)]
Btrfs: fix sync subvol/snapshot creation
We were incorrectly taking the async path even for the sync ioctls by
passing in &transid unconditionally.
There's ample room for further cleanup here, but this keeps the fix simple.
Signed-off-by: Sage Weil <sage@newdream.net>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Mon, 6 Dec 2010 07:02:36 +0000 (07:02 +0000)]
Btrfs: Fix page leak in compressed writeback path
"start + num_bytes >= actual_end" can happen when compressed page writeback races
with file truncation. In that case we need unlock and release pages past the end
of file.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Wed, 8 Dec 2010 17:24:01 +0000 (12:24 -0500)]
Btrfs: do not BUG if we fail to remove the orphan item for dead snapshots
Not being able to delete an orphan item isn't a horrible thing. The worst that
happens is the next time around we try and do the orphan cleanup and we can't
find the referenced object and just delete the item and move on.
Signed-off-by: Josef Bacik <josef@redhat.com>
David S. Miller [Fri, 10 Dec 2010 20:51:02 +0000 (12:51 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Nicolas Dichtel [Tue, 7 Dec 2010 23:38:31 +0000 (23:38 +0000)]
ipv6: fix nl group when advertising a new link
New idev are advertised with NL group RTNLGRP_IPV6_IFADDR, but
should use RTNLGRP_IPV6_IFINFO.
Bug was introduced by commit
8d7a76c9.
Signed-off-by: Wang Xuefu <xuefu.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 10 Dec 2010 20:27:49 +0000 (12:27 -0800)]
connector: add module alias
Since connector can be built as a module and uses netlink socket
to communicate. The module should have an alias to autoload when socket
of NETLINK_CONNECTOR type is requested.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Lucina [Fri, 10 Dec 2010 00:04:05 +0000 (00:04 +0000)]
net: Document the kernel_recvmsg() function
Signed-off-by: Martin Lucina <mato@kotelna.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael J. Wysocki [Wed, 8 Dec 2010 15:32:14 +0000 (15:32 +0000)]
r8169: Fix runtime power management
I noticed that one of the post-2.6.36 patches broke runtime PM of the
r8169 on my MSI Wind test machine in such a way that the link was not
brought up after reconnecting the network cable.
In the process of debugging the issue I realized that we only should
invoke the runtime PM functions in rtl8169_check_link_status() when
link change is reported and if we do so, the problem goes away.
Moreover, this allows rtl8169_runtime_idle() to be simplified quite
a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chuck Lever [Fri, 10 Dec 2010 17:31:14 +0000 (12:31 -0500)]
NFS: Fix panic after nfs_umount()
After a few unsuccessful NFS mount attempts in which the client and
server cannot agree on an authentication flavor both support, the
client panics. nfs_umount() is invoked in the kernel in this case.
Turns out nfs_umount()'s UMNT RPC invocation causes the RPC client to
write off the end of the rpc_clnt's iostat array. This is because the
mount client's nrprocs field is initialized with the count of defined
procedures (two: MNT and UMNT), rather than the size of the client's
proc array (four).
The fix is to use the same initialization technique used by most other
upper layer clients in the kernel.
Introduced by commit
0b524123, which failed to update nrprocs when
support was added for UMNT in the kernel.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=24302
BugLink: http://bugs.launchpad.net/bugs/683938
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Tested-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org # >= 2.6.32
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Thomas Bogendoerfer [Tue, 7 Dec 2010 22:21:52 +0000 (22:21 +0000)]
hso: IP checksuming doesn't work on GE0301 option cards
There is definitly a problem, that some option cards send up broken
IP pakets leading to corrupted IP packets. These corruptions aren't
detected, because the driver claims that the packets are already
checksummed. This change removes the CHECKSUM_UNNECESSARY option
and let IP detect broken data.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Egerer [Mon, 6 Dec 2010 23:28:56 +0000 (23:28 +0000)]
xfrm: Fix xfrm_state_migrate leak
xfrm_state_migrate calls kfree instead of xfrm_state_put to free
a failed state. According to git commit
553f9118 this can cause
memory leaks.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Mon, 6 Dec 2010 09:05:50 +0000 (09:05 +0000)]
net: Convert netpoll blocking api in bonding driver to be a counter
A while back I made some changes to enable netpoll in the bonding driver. Among
them was a per-cpu flag that indicated we were in a path that held locks which
could cause the netpoll path to block in during tx, and as such the tx path
should queue the frame for later use. This appears to have given rise to a
regression. If one of those paths on which we hold the per-cpu flag yields the
cpu, its possible for us to come back on a different cpu, leading to us clearing
a different flag than we set. This results in odd netpoll drops, and BUG
backtraces appearing in the log, as we check to make sure that we only clear set
bits, and only set clear bits. I had though briefly about changing the
offending paths so that they wouldn't sleep, but looking at my origional work
more closely, it doesn't appear that a per-cpu flag is warranted. We alrady
gate the checking of this flag on IFF_IN_NETPOLL, so we don't hit this in the
normal tx case anyway. And practically speaking, the normal use case for
netpoll is to only have one client anyway, so we're not going to erroneously
queue netpoll frames when its actually safe to do so. As such, lets just
convert that per-cpu flag to an atomic counter. It fixes the rescheduling bugs,
is equivalent from a performance perspective and actually eliminates some code
in the process.
Tested by the reporter and myself, successfully
Reported-by: Liang Zheng <lzheng@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hilman [Wed, 8 Dec 2010 22:40:40 +0000 (22:40 +0000)]
OMAP2+: PM/serial: fix console semaphore acquire during suspend
commit
0d8e2d0dad98a693bad88aea6876ac8b94ad95c6 (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin Hilman [Wed, 8 Dec 2010 01:02:12 +0000 (01:02 +0000)]
OMAP1: SRAM: fix size for OMAP1611 SoCs
Kernel was failing to boot on omap1611 based OSK boards due to
mis-configured SRAM size. Existing code was using a hard-coded value
for 250k, which was then rounded down by PAGE_SIZE. Increasing this to
256k allows kernel to boot on omap1611 SoCs.
Problem reported by and initial fix suggested by Tim Bird.
Thanks to Tony Lindgren for helping diagnose the problem to being
specific to OMAP1611 and not affecting OMAP1610/OMAP1623.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Christoph Hellwig [Tue, 7 Dec 2010 10:16:41 +0000 (10:16 +0000)]
xfs: log timestamp changes to the source inode in rename
Now that we don't mark VFS inodes dirty anymore for internal
timestamp changes, but rely on the transaction subsystem to push
them out, we need to explicitly log the source inode in rename after
updating it's timestamps to make sure the changes actually get
forced out by sync/fsync or an AIL push.
We already account for the fourth inode in the log reservation, as a
rename of directories needs to update the nlink field, so just
adding the xfs_trans_log_inode call is enough.
This fixes the xfsqa 065 regression introduced by:
"xfs: don't use vfs writeback for pure metadata modifications"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Alexey Starikovskiy [Thu, 9 Dec 2010 22:07:54 +0000 (17:07 -0500)]
ACPI: EC: Add another dmi match entry for MSI hardware
http://bugzilla.kernel.org/show_bug.cgi?id=15418
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
Mike Miller [Wed, 1 Dec 2010 17:16:07 +0000 (11:16 -0600)]
[SCSI] hpsa: fix redefinition of PCI_DEVICE_ID_CISSF
PCI_DEVICE_ID_CISSF is defined as 323b in pci_ids.h but redefined as 3fff in
hpsa.c. The ID of 3fff will _never_ ship as a standalone controller. It is
intended only as part a complete storage solution. As such, this patch
removes the redefinition and the StorageWorks P1210m from the product table.
It also removes a duplicate line for the "unknown" controller support.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Zhang Rui [Wed, 8 Dec 2010 02:40:49 +0000 (10:40 +0800)]
ACPI battery: update status upon sysfs query
Sometimes the Battery driver doesn't get notifications when it's
plugged/unplugged. And this results in the incorrect Battery
status reported by the power supply sysfs I/F.
Update Battery status first when querying from sysfs.
http://marc.info/?l=linux-acpi&m=
128855015826728&w=2
Tested_by: Seblu <seblu@seblu.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 8 Dec 2010 02:40:45 +0000 (10:40 +0800)]
ACPI ac: update AC status upon sysfs query
http://marc.info/?l=linux-acpi&m=
128855015826728&w=2
https://bugzilla.kernel.org/show_bug.cgi?id=21722
Tested_by: Seblu <seblu@seblu.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Madhuranath Iyengar [Wed, 24 Nov 2010 00:52:50 +0000 (16:52 -0800)]
[SCSI] qla2xxx: Update version number to 8.03.05-k0.
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Saurav Kashyap [Wed, 24 Nov 2010 00:52:49 +0000 (16:52 -0800)]
[SCSI] qla2xxx: Properly set the return value in qla2xxx_eh_abort function.
A return value is not set for the successful case and it has a garbage value.
This fix will set the default value to SUCCESS and in case of any failures
it is changed.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Andrew Vasquez [Wed, 24 Nov 2010 00:52:48 +0000 (16:52 -0800)]
[SCSI] qla2xxx: Correct issue where NPIV-config data was not being allocated for 82xx parts.
This would cause a panic while reading the NPIV-config data.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Hernandez [Wed, 24 Nov 2010 00:52:47 +0000 (16:52 -0800)]
[SCSI] qla2xxx: Change MSI initialization from using incorrect request_irq parameter.
IRQF_SHARED flag should not be set when calling request_irq for MSI
since this interrupt mechanism cannot be shared like standard INTx.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Hernandez [Wed, 24 Nov 2010 00:52:46 +0000 (16:52 -0800)]
[SCSI] qla2xxx: Populate Command Type 6 LUN field properly.
Use the host_to_fcp_swap call to correctly populate the LUN field
in the Command Type 6 path. This field is used during LUN reset
cleanup and must match the field used in the FCP command.
Cc: stable@kernel.org
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Josef Bacik [Wed, 8 Dec 2010 17:22:34 +0000 (12:22 -0500)]
Btrfs: fixup return code for btrfs_del_orphan_item
If the orphan item doesn't exist, we return 1, which doesn't make any sense to
the callers. Instead return -ENOENT if we didn't find the item. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Josef Bacik [Wed, 8 Dec 2010 14:15:11 +0000 (09:15 -0500)]
Btrfs: do not do fast caching if we are allocating blocks for tree_root
Since the fast caching uses normal tree locking, we can possibly deadlock if we
get to the caching via a btrfs_search_slot() on the tree_root. So just check to
see if the root we are on is the tree root, and just don't do the fast caching.
Reported-by: Sage Weil <sage@newdream.net>
Signed-off-by: Josef Bacik <josef@redhat.com>
Josef Bacik [Fri, 3 Dec 2010 18:17:53 +0000 (13:17 -0500)]
Btrfs: deal with space cache errors better
Currently if the space cache inode generation number doesn't match the
generation number in the space cache header we will just fail to load the space
cache, but we won't mark the space cache as an error, so we'll keep getting that
error each time somebody tries to cache that block group until we actually clear
the thing. Fix this by marking the space cache as having an error so we only
get the message once. This patch also makes it so that we don't try and setup
space cache for a block group that isn't cached, since we won't be able to write
it out anyway. None of these problems are actual problems, they are just
annoying and sub-optimal. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Josef Bacik [Fri, 19 Nov 2010 14:41:10 +0000 (09:41 -0500)]
Btrfs: fix use after free in O_DIRECT
This fixes a bug where we use dip after we have freed it. Instead just use the
file_offset that was passed to the function. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Christof Schmitt [Thu, 18 Nov 2010 13:53:18 +0000 (14:53 +0100)]
[SCSI] zfcp: Issue FCP command without holding SCSI host_lock
Interrupting the connection to the FCP channel while I/O requests are
being issued can lead to this deadlock. scsi_dispatch_cmd already
holds the host_lock while the recovery trigger tries to acquire the
host_lock again when iterating through the scsi_devices.
INFO: lockdep is turned off.
BUG: spinlock lockup on CPU#1, blast/9660,
0000000078f38878
CPU: 1 Not tainted 2.6.35.7SWEN2 #2
Process blast (pid: 9660, task:
0000000071f75940, ksp:
0000000074393ac0)
0000000074393640 00000000743935c0 0000000000000002 0000000000000000
0000000074393660 00000000743935d8 00000000743935d8 00000000005590c2
0000000000000000 0000000078f38878 0000000026ede800 0000000078f38878
000000000000000d 040000000000000c 0000000074393628 0000000000000000
0000000000000000 0000000000100b2a 00000000743935c0 0000000074393600
Call Trace:
([<
0000000000100a32>] show_trace+0xee/0x144)
[<
00000000003be202>] do_raw_spin_lock+0x112/0x178
[<
000000000055d408>] _raw_spin_lock_irqsave+0x90/0xb0
[<
00000000003f1514>] __scsi_iterate_devices+0x38/0xbc
[<
00000000004849b0>] zfcp_erp_clear_adapter_status+0xd0/0x16c
[<
000000000048587a>] zfcp_erp_adapter_reopen+0x3a/0xb4
[<
0000000000489812>] zfcp_fsf_req_send+0x166/0x180
[<
000000000048c8d6>] zfcp_fsf_fcp_cmnd+0x272/0x408
[<
000000000048f864>] zfcp_scsi_queuecommand+0x11c/0x1e0
[<
00000000003f1f2a>] scsi_dispatch_cmd+0x1d6/0x324
[<
00000000003f9910>] scsi_request_fn+0x42c/0x56c
[<
00000000003828ae>] __blk_run_queue+0x86/0x140
[<
000000000037f742>] elv_insert+0x11a/0x208
[<
000000000038104c>] blk_insert_cloned_request+0x84/0xe4
[<
000003c0032b7c64>] dm_dispatch_request+0x6c/0x94 [dm_mod]
[<
000003c0032b7d5c>] map_request+0xd0/0x100 [dm_mod]
[<
000003c0032b9a78>] dm_request_fn+0xec/0x1bc [dm_mod]
[<
0000000000382c0e>] generic_unplug_device+0x5a/0x6c
[<
000003c0032b7f98>] dm_unplug_all+0x74/0x9c [dm_mod]
[<
00000000001d1272>] sync_page+0x76/0x9c
[<
00000000001d12ba>] sync_page_killable+0x22/0x60
[<
000000000055a768>] __wait_on_bit_lock+0xc0/0x124
[<
00000000001d1140>] __lock_page_killable+0x78/0x84
[<
00000000001d351c>] generic_file_aio_read+0x5a4/0x7e8
[<
0000000000228ec0>] do_sync_read+0xc8/0x12c
[<
0000000000229edc>] vfs_read+0xac/0x1ac
[<
000000000022a0d8>] SyS_read+0x58/0xa8
[<
00000000001146de>] sysc_noemu+0x10/0x16
[<
00000200000493c4>] 0x200000493c4
INFO: lockdep is turned off.
Call zfcp_fsf_fcp_cmnd without the host_lock and disable the
interrupts when acquiring the req_q_lock. According to the patch
description in "[PATCH] Eliminate error handler overload of the SCSI
serial number", the serial_number is not used, so simply drop the
queuecommand wrapper function and run zfcp_scsi_queuecommand without
holding the host_lock.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Swen Schillig [Wed, 17 Nov 2010 13:23:43 +0000 (14:23 +0100)]
[SCSI] zfcp: Prevent usage w/o holding a reference
The ERP got values assigned for which no reference was taken. This
can lead to an unpredictable race condition. Fix this by only
assigning the values which are required and for which a reference was
pulled or is held implicitly.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Swen Schillig [Wed, 17 Nov 2010 13:23:42 +0000 (14:23 +0100)]
[SCSI] zfcp: No ERP escalation on gpn_ft eval
If the evaluation of GPN_FT requests wants to remove an invalid port
from the system the zfcp_erp_port_shutdown function is triggered.
Depending on the system status a superior action (e.g. adapter reopen)
is required. This can lead to an invalid mem access of the port struct
which might be freed at the time since the superior action is not
holding a reference of the port which triggered this ERP action.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Swen Schillig [Wed, 17 Nov 2010 13:23:41 +0000 (14:23 +0100)]
[SCSI] zfcp: Correct false abort data assignment.
The request data assignment between the fsf abort initiator and its
corresponding handler is not consistent and leads to an unpredictable
behaviour, e.g. kernel panic. This patch fixes this issue and assigns
the correct value.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Swen Schillig [Wed, 17 Nov 2010 13:23:40 +0000 (14:23 +0100)]
[SCSI] zfcp: Fix common FCP request reception
The reception of a common FCP request should only be evaluated if the
corresponding SCSI request data is available. Therefore put the
information under the lock protection and verify the existence before
processing. This fixes the following kernel panic.
Unable to handle kernel pointer dereference at virtual kernel address
0000000180000000
Oops: 003b [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU: 0 Not tainted 2.6.35.7-45.x.
20101007-s390xdefault #1
Process blast (pid: 9711, task:
00000000a3be8e40, ksp:
00000000b221bac0)
Krnl PSW :
0704300180000000 0000000000489878 (zfcp_fsf_fcp_handler_common+0x4c/0x3a0)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:3 PM:0 EA:3
Krnl GPRS:
00000000b663c1b8 0000000180000000 000000007ab5bdf0 0000000000000000
00000000b0ccd800 0000000000000018 07000000a3be8e78 00000000b5d3e600
000000007ab5bdf0 0000000000000066 00000000b72137f0 00000000b72137f0
0000000000000000 00000000005a8178 00000000bdf37a60 00000000bdf379f0
Krnl Code:
0000000000489866:
e3c030000004 lg %r12,0(%r3)
000000000048986c:
e310c0000004 lg %r1,0(%r12)
0000000000489872:
e31011e00004 lg %r1,480(%r1)
>
0000000000489878:
581011ec l %r1,492(%r1)
000000000048987c:
a774001c brc 7,4898b4
0000000000489880:
b91400b1 lgfr %r11,%r1
0000000000489884:
5810405c l %r1,92(%r4)
0000000000489888:
5510d00c cl %r1,12(%r13)
Call Trace:
([<
000000000010d344>] debug_event_common+0x22c/0x244)
[<
000000000048a0b4>] zfcp_fsf_fcp_cmnd_handler+0x2c/0x3b4
[<
000000000048b5b6>] zfcp_fsf_req_complete+0x1b6/0x9dc
[<
000000000048bede>] zfcp_fsf_reqid_check+0x102/0x138
[<
000000000048e478>] zfcp_qdio_int_resp+0x70/0x110
[<
000000000044a1ec>] qdio_kick_handler+0xb0/0x19c
[<
000000000044c228>] __tiqdio_inbound_processing+0x30c/0xebc
[<
000000000014a5fc>] tasklet_action+0x1b4/0x1e8
[<
000000000014b676>] __do_softirq+0x106/0x1cc
[<
000000000010d91a>] do_softirq+0xe6/0xec
[<
000000000014b0c8>] irq_exit+0xd4/0xd8
[<
00000000004307ec>] do_IRQ+0x7c0/0xf54
[<
0000000000114d28>] io_return+0x0/0x16
[<
000000000055fef0>] sub_preempt_count+0x50/0xe4
([<
00000000b1f873c0>] 0xb1f873c0)
[<
000000000055e25a>] _raw_spin_unlock+0x46/0x74
[<
0000000000241c40>] __d_lookup+0x288/0x2c8
[<
000000000023502c>] do_lookup+0x7c/0x25c
[<
0000000000237fa8>] link_path_walk+0x5e4/0xe2c
[<
0000000000238a00>] path_walk+0x98/0x148
[<
0000000000238c98>] do_path_lookup+0x74/0xc0
[<
000000000023989c>] user_path_at+0x64/0xa4
[<
000000000022e366>] vfs_fstatat+0x4e/0xb0
[<
000000000022e4d6>] SyS_newstat+0x2e/0x54
[<
00000000001146de>] sysc_noemu+0x10/0x16
[<
0000020000153456>] 0x20000153456
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<
000000000048a0ae>] zfcp_fsf_fcp_cmnd_handler+0x26/0x3b4
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Bottomley [Wed, 17 Nov 2010 16:10:57 +0000 (10:10 -0600)]
[SCSI] Eliminate error handler overload of the SCSI serial number
The error handler is using the test cmd->serial_number == 0 in the
abort routines to signal that the command to be aborted has already
completed normally. This design was to close a race window in the
original error handler where a command could go through the normal
completion routines after it timed out but before error handling was
started.
Mike Anderson pointed out that when we converted our timeout and
softirq completions, we picked up atomicity here because the block
layer now mediates this with the REQ_ATOM_COMPLETE flag and guarantees
that *either* the command times out or our done routine is called, but
ensures we can't get both occurring. That makes the serial number
zero check redundant and it can be removed.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Anil Ravindranath [Tue, 16 Nov 2010 21:43:41 +0000 (13:43 -0800)]
[SCSI] pmcraid: disable msix and expand device config entry
Firmware requires a larger configuration entry size than the driver
currently allows, and MSI-X pretty much doesn't work with current FW,
so disable it for now.
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Sun, 14 Nov 2010 16:12:04 +0000 (11:12 -0500)]
[SCSI] bsg: correct fault if queue object removed while dev_t open
This patch corrects an issue in bsg that results in a general protection
fault if an LLD is removed while an application is using an open file
handle to a bsg device, and the application issues an ioctl. The fault
occurs because the class_dev is NULL, having been cleared in
bsg_unregister_queue() when the driver was removed. With this
patch, a check is made for the class_dev, and the application
will receive ENXIO if the related object is gone.
Signed-off-by: Carl Lajeunesse <carl.lajeunesse@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>