[SCSI] fnic: fnic Driver Tuneables Exposed through CLI

Introduced module params to provide dynamic way of configuring
queue depth.

Added support to get max io throttle count through UCSM to
configure maximum outstanding IOs supported by fnic and push
that value to scsi mid-layer.

  Supported IO throttle values:

  UCSM IO THROTTLE VALUE        FNIC MAX OUTSTANDING IOS
  ------------------------------------------------------
        16 (Default)                    2048
        <= 256                          256
        > 256                           <ucsm value>

Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg

Kernel panics due to NULL lport while executing the log message because
of synchronization issues between libfc and scsi transport fc. Checking
for NULL pointers at the beginning of this routine would resolve the issue
from kernel panic point of view.

Signed-off-by: Sesidhar Baddel <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset

Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset in case of
timing issue and also to some extent locking issue where abts and terminate
is happening around same timing.

The code changes are intended to update CMD_STATE(sc) and
io_req->abts_done together.

Signed-off-by: Sesidhar Beddel <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] fnic: Remove QUEUE_FULL handling code

Remove fnic driver QUEUE_FULL handling code instead let SCSI mid layer
handle queue full and use its algorithm to ramp down/up queue

Signed-off-by: Suma Ramars <sramars@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up

Issue was seen when SCSI buffer address is more than 40 bits in system
with more than 1.1TB RAM. When SCSI buffer is passed to VIC, it is failing
to map to correct buffer address, as DMA mask is set to 40 bits in driver
initialization. Corrected DMA_MASK from 40-bits to 64-bits to avoid masking
41-64 bits addresses.

Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] fnic: FC stat param seconds_since_last_reset not getting updated

Code to reset fc_host statistics.
echo 1 > /sys/class/fc_host/hostX/statistics/reset_statistics clears fc_host stats,
the code also issues command to fnic firmware to clear vnic stats.

Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sd: Fix potential out-of-bounds access

This patch fixes an out-of-bounds error in sd_read_cache_type(), found
by Google's AddressSanitizer tool.  When the loop ends, we know that
"offset" lies beyond the end of the data in the buffer, so no Caching
mode page was found.  In theory it may be present, but the buffer size
is limited to 512 bytes.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Back out data count,(residual fcfi_parm) fix for bad target.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed mailbox memory leak.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fix random errors using first burst

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed not able to log informational messages at early stage of driver init time

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] lpfc 8.3.42: Fixed using unsafe linked list macro for walking and deleting linked list

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid_sas: addded support for big endian architecture

This patch will add big endian architecture support to megaraid_sas
driver. The support added is for LSI MegaRAID all generation controllers-
(3Gb/s, 6Gb/s and 12 Gb/s controllers).

We have done basic sanity test @ppc64 arch and @x86_64. Additional
testing/observations are welcome.

[jejb: fix up rejections]
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] aic7xxx: fix swapped arguments in ahc_find_pci_device

The prototype for ahc_9005_subdevinfo_valid shows that the caller has the
arguments in the wrong order.

 637 ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor,
 638                           uint16_t subdevice, uint16_t subvendor)

Signed-off-by: Dave Jones <davej@fedoraproject.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: bump driver version to reflect changes

Changes the version of hpsa so we know something has changed. Please consider
this for inclusion.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: housekeeping patch for device_id and product arrays

This patch does a bit of housekeeping for hpsa. Change lowercase alpha hex
digits to uppercase for consistency within the driver. Also moves the P822se
in the tables to keep controllers of each family grouped together.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: add HP Smart Array Gen8 names

Add the marketing names for HP Smart Array Gen8 controllers. Also removes an
unused ID. Please consider this for inclusion.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] hpsa: add HP Smart Array Gen9 PCI ID's

This patch adds the PCI ID's for HP Smart Array Gen9 controllers. Please
consider this patch for inclusion.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ufs: configure the attribute for power mode

UIC attributes can be set with using DME_SET command for
power mode change. For configuration the link capability
attributes are used, which is updated after successful
link startup.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ufs: add operation for the uic power mode change

Setting PA_PWRMode using DME_SET triggers the power mode
change. And then the result will be given by the HCS.UPMCRS.
This operation should be done atomically.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ufs: add dme configuration primitives

Implements to support GET and SET operations of the DME.
These operations are used to configure the behavior of
the UNIPRO. Along with basic operation, {Peer/AttrSetType}
can be mixed.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ufs: fix the setting interrupt aggregation counter

IACTH(Interrupt aggregation counter threshold) value is allowed
up to 0x1F and current setting value is the maximum.
This value is related with NUTRS(max:0x20) of HCI's capability.
Considering HCI controller doesn't support the maximum, IACTH
setting should be adjusted with possible value.
For that, existing 'ufshcd_config_int_aggr' is split into two part
[reset, configure].

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ufs: find out sense data over scsi status values

Unlike 'GOOD' and 'CHECK CONDITION', other status values in
Response UPIU may or may not contain sense data. That is returning
sense data isn't obvious. So, in this case the Data Segment Length
field should be checked. If a non-zero value, it means that UPIU
has Sense Data in the Data Segment area.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid_sas: Version and Changelog update

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] megaraid_sas: Add High Availability clustering support using shared Logical Disks

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] Allow MPT Fusion SAS 3.0 driver to be built into the kernel

Right now the Makefile for the mpt3sas driver does not even allow the
driver to be built into the kernel.  So fix that up, as there doesn't
seem to be any obvious reason why this shouldn't be done.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ibmvfc: Fix for offlining devices during error recovery

This fixes an issue seen with devices getting marked offline
in a scenario where a VIOS was getting rebooted while a
client VFC adapter is in SCSI EH and prevents unnecessary
EH escalation in some scenarios.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] ibmvscsi: Fix little endian issues

The hypervisor is big endian, so little endian kernel builds need
to byteswap.

[jejb: fix checkpatch errors]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: Remove null test for stack allocated fw_coredump_buffer

Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: coccinelle - Replace memcpy with struct assignment

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: smatch - Remove test for impossible condition (uint8 > 255)

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: smatch - Fix overrun due to sprintf appending NULL

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: smatch - Fix dereference that occurs prior to check

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: smatch - Use biwise rather than logical AND for checking if any bit set

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sg: push file descriptor list locking down to per-device locking

Push file descriptor list locking down to per-device locking. Let sg_index_lock
only protect device lookup.
sdp->detached is also set and checked with this lock held.

Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sg: checking sdp->detached isn't protected when open

@detached is set under the protection of sg_index_lock. Without getting the
lock, new sfp will be added during sg removal and there is no chance for it
to be picked out. So check with sg_index_lock held in sg_add_sfp().

Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sg: no need sg_open_exclusive_lock

Open exclusive check is protected by o_sem, no need sg_open_exclusive_lock.
@exclude is used to record which type of rwsem we are holding.

Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] sg: use rwsem to solve race during exclusive open

A race condition may happen if two threads are both trying to open the same sg
with O_EXCL simultaneously. It's possible that they both find fsds list is
empty and get_exclude(sdp) returns 0, then they both call set_exclude() and
break out from wait_event_interruptible and resume open.

Now use rwsem to protect this process. Exclusive open gets write lock and
others get read lock. The lock will be held until file descriptor is closed.
This also leads 'exclude' only a status rather than a check mark.

Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] scsi_debug: fix logical block provisioning support when unmap_alignment != 0

Commit b90ebc3d5c41c9164ae04efd2e4f8204c2a186f1 ("[SCSI] scsi_debug:
fix logical block provisioning support") fixed several issues with
logical block provisioning support, but it still doesn't properly fix
the cases when unmap_alignment > 0.

For example, load scsi_debug module with the following module parameters
and make all blocks mapped by filling the storage with zero.

        # modprobe scsi_debug lbpu=1 unmap_alignment=1 unmap_granularity=4
        # dd if=/dev/zero of=$DEV

Then, try to unmap the first unmappable blocks at lba=1, but GET LBA STATUS
unexpectedly reports that the last UNMAP has done nothing.

        # sg_unmap --lba=1 --num=4 $DEV
        # sg_get_lba_status --lba=1 $DEV
        descriptor LBA: 0x0000000000000001  blocks: 16383  mapped

The problem is in map_index_to_lba(), which should return the first
LBA which is corresponding to a given index of provisioning map
(map_storep).

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] scsi_debug: fix endianness bug in sdebug_build_parts()

With module parameter num_parts > 0, partition table is built on the
ramdisk storage when loading the driver.  Unfortunately, there is an
endianness bug in sdebug_build_parts().  So the partition table is not
correctly initialized on big-endian systems.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Update the driver version to 8.06.00.08-k.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: print MAC via %pMR.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Correction to message ids.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Correctly print out/in mailbox registers.

At mailbox/buffer debug level, print the correct values of the
outgoing and incoming mailbox registers.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add a new interface to update versions.

On any Adapter when we flash through FC/FCoE without card reset option it still
shows the Running FW version in Flashed FW version. This new interface will be
used by API to instruct the driver to update its cache versions.

Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Move queue depth ramp down message to i/o debug level.

Unless there is a need to observe them, the queue depth ramp up/down messages
are a nuisance and may cause the system to become unresponsive so move it a
non-default logging level.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Select link initialization option bits from current operating mode.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add loopback IDC-TIME-EXTEND aen handling support.

Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Correct Interrupt Register offset for ISPFX00

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Remove handling of Shutdown Requested AEN from qlafx00_process_aen().

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Send all AENs for ISPFx00 to above layers.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add changes in initialization for ISPFX00 cards with BIOS

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add changes to support extended IOs for ISPFX00

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add missing FCP statistics to sysfs interface.

Add the missing FCP statistics to sysfs.
Add reset FCP statistics functionality via sysfs.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Make log message that prints when a completion status requires a port down more readable.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add critical temperature handling for ISPFX00.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Acked-by: Srinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Notify ISPFX00 firmware when driver is unloaded or system is shut down.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Acked-by: Srinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Reconfigure thermal temperature.

For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add setting of driver version string for vendor application.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Remove QL_DEBUG_LEVEL_17 defines from qla_nx.c.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add ISPFX00 specific bus reset routine.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Perform warm reset every 2 minutes if firmware load fails for ISPFX00.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Acked-by: Srinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Set factory reset recovery timeout to 10 min. for ISPFX00.

Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Acked-by: Srinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Correct multiqueue offset calculations.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Fix incorrect test after list_for_each_entry() exits.

list_for_each_entry() never leaves the iterator pointing to null.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Add support for ISP8044.

[jejb: checkpatch fixes]
Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Print some variables to hexadecimal string via %*phN format

The patch changes a specifier used to output some variables. Instead of using
stack for each byte the '%*ph[CN]' allows to take a one pointer and prints
entire buffer as a hexadecimal string with the separator ':' or ''.

Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt3sas: Remove phys on topology change

Signed-off-by: Jan Vesely <jvesely@redhat.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt2sas: Remove phys on topology change.

Signed-off-by: Jan Vesely <jvesely@redhat.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] bfa: firmware update to 3.2.1.1

This patch updates the firmware to address the thermal notification issue

Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] esas2r: ATTO Technology ExpressSAS 6G SAS/SATA RAID Adapter Driver

This is a new driver for ATTO Technology's ExpressSAS series of hardware RAID
adapters.  It supports the following adapters:

    - ExpressSAS R60F
    - ExpressSAS R680
    - ExpressSAS R608
    - ExpressSAS R644

Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] eata_pio: off by one in eata_pio_detect()

Smatch complains that the reg_IRQ[] array only has MAXIRQ (16) elements
so we are one space beyond the end of the array here.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update driver version to 5.04.00-k1

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Return error if minidump data collection fails

Return error from function qla4_8xxx_collect_md_data()
if minidump data collection fails.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Fix the minidump data collection check in for loop

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Add pex-dma support for capturing minidump

Add pex-dma support for ISP8324 and ISP8042 to improve
the minidump capture time.

Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] zfcp: enable FCP hardware data router by default

Enabling the data router support by default
can increase performance in certain situations.
It is safe to do so and tolerated in LPAR and under z/VM
in case there is no data router support in that environment.

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] zfcp: dead code removal

Get rid of unused function zfcp_fsf_get_req and corresponding
prototype definition.

Commit a54ca0f62f953898b05549391ac2a8a4dad6482b in v2.6.28
"[SCSI] zfcp: Redesign of the debug tracing for HBA records."
accidentally introduced this code which was dead in the first place.

Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] zfcp: cleanup use of obsolete strict_strto* functions

strict_strtoul and friends are obsolete. Use kstrtoul functions
instead.

Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] zfcp: consistently use appropriate SBAL flag definitions

minor cleanup for status read request

Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] mpt3sas: Added a driver module parameter max_msix_vectors

Added a driver module parameter max_msix_vectors. Using this module parameter
the maximum number of MSI-X vectors could be set.

The number of MSI-X vectors used would be the minimum of MSI-X vectors
supported by the HBA, the number of CPU cores and the value set to
max_msix_vectors module parameter.

The default value of this module parameter is set to 8. The default value of
this parameter is set to 8 inorder to reduce the amount of memory required for
Reply Descriptor Post queue.  This is because with the higher MSI-X vectors,
some times kernel is not able to allocate the requested amount of memory and
crash is observed. To overcome this problem, the default value is set to 8.

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update driver version to 5.04.00-k0

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Update Copyright header

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Implementation of ACB configuration during Loopback for ISP8042

While loopback diagnostic is in progress, disable the ACB which resets
all the active connections to target. Disable ACB would filter out all
the DHCP multicast and broadcast packets which otherwise cause the
diagnostic test to take longer time to complete or failures in some
other cases.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[SCSI] qla4xxx: Added support for ISP8042

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>