BACKPORT: FROMLIST: mmc: dw_mmc: introduce timer for broken command transfer over scheme

Per the databook of designware mmc controller 2.70a, table 3-2, cmd
done interrupt should be fired as soon as the the cmd is sent via
cmd line. And the response timeout interrupt should be generated
unconditioinally as well if the controller doesn't receive the resp.
However that doesn't seem to meet the fact of rockchip specified Soc
platforms using dwmmc. We have continuously found the the cmd done or
response timeout interrupt missed somehow which took us a long time to
understand what was happening. Finally we narrow down the root to
the reconstruction of sample circuit for dwmmc IP introduced by
rockchip and the buggy design sweeps over all the existing rockchip
Socs using dwmmc disastrously.

It seems no way to work around this bug without the proper break-out
mechanism so that we seek for a parallel pair the same as the handling
for missing data response timeout, namely dto timer. Adding this cto
timer seems easily to handle this bug but it's hard to restrict
the code under the rockchip specified context. So after merging this
patch, it sets up the cto timer for all the platforms using dwmmc IP
which isn't ideal but at least we don't advertise new quirk here.
Fortunately, no obvious performance regression was found by test and the
pre-existing similar catch-all timer for sdhci has proved it's an acceptant
way to make the code as robust as possible.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
[shawn.lin: rewrite the code and the commit msg throughout]
Change-Id: I47238c9758fe74b98a1dd3939f22e569261e696f
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
(cherry picked from https://patchwork.kernel.org/patch/9834331/)

drm/rockchip: hdmi: Limit rk3229/rk3328 max output resolution

Limit RK3229/RK3328 max output resolution to 4K 50/60 YCbCr420 mode.

Change-Id: Icb934f6f057503ccb619f4ca6167b0958def336a
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

arm64: dts: rockchip: rk3328-evb: enable hdmiphy

Change-Id: I173ec8ec759a1404f31718c8647cf6eb6315061f
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

arm64: dts: rockchip: rk3328: hdmi enable inno-hdmi-phy driver

Change-Id: I3d4c6dfcaffeb6679666fcedf58e645d26205efa
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

drm: bridge: dw-hdmi: delete phy ops read/write

RK3328/RK3228 phy registers are mapped by inno-hdmi-phy driver,
there is no need to register hdmi phy debugfs on RK3328/RK3228.

Change-Id: I1e259b75ee7af6f29dffd5526d67776d5c6853ae
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

drm/rockchip: hdmi: use inno-hdmi-phy driver to operate rk3328 hdmi phy

Change-Id: Ic090fec14f076ba634d35cb85c59c160c47d0058
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

phy: rockchip-inno-hdmi-phy: support rk3328 hdmi phy

RK3328 hdmi phy is an upgraded version of 3228 hdmi phy, with
a completely different register layout. It improves physical
and antistatic capabilities.

It's max output bandwidth is same as rk3228 hdmi phy, optimized
up to 3.72Gbps per TMDS link.

Change-Id: I03c718c49e44cfeaa113e3ed07eec7055b4380cc
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

arm64: rockchip_linux_defconfig: enable CONFIG_PHY_ROCKCHIP_INNO_HDMI_PHY

Change-Id: Ie775672f43e6c2491d750c82f604c454a367e136
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>

drm/rockchip: vop: support get register by name

When get vop base register byname failed, retry first entry.

Change-Id: I60f4ebd901d353966c94734dd796dc702ae06f3f
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>

dt-bindings: rockchip: vop: introduce registers names

Change-Id: I0df821f2582b26e26cfe3059db19a90b206df5c5
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>

arm64: dts: rockchip: rk3399-android: enable fiq mode

Change-Id: Ib40f065ba6ac2f597a27db87a46a0d2f7c0714ed
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>

ARM: dts: rk3288-android: enable dmc auto frequency adjustment

Enable dmc auto frequency adjustment and
set dmc minimum frequency to 400MHz for better performance

Change-Id: I0d2a192f438c23d879158f55dc948205f67f8663
Signed-off-by: Steven Chen <cw@rock-chips.com>

spi: rockchip: test: update driver

Change-Id: I773cdc245fcdf8eee10dd7983343f206aecb856c
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>

spi: rockchip: rockchip_spi_prepare_dma return 1 if it is ok

If rockchip_spi_prepare_dma return 0, spi_transfer_one_message
won't wait for the dma complete event. Which may cause unknown
error.

Change-Id: Idf51a737bbd9fa9b9d1ae749636fe524de1cbfa9
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>

soc: rockchip: vendor storage support realloc

To rewrite the same id with the data size large than first alloc size,
it`s will write fail. This commit will support realloc new memory
for rewrite.

Change-Id: Icd53afd072328dc45f1faae033471c5069664f05
Signed-off-by: Zhaoyifeng <zyf@rock-chips.com>

 Merge tag 'v4.4.76' into linux-linaro-lsk-v4.4

 This is the 4.4.76 stable release

arm64: dts: rockchip: use dwmmc for rk3366

Change-Id: I3ecadd51e34545af61a1bfcc54ee0d6f045c40fa
Signed-off-by: Zorro Liu <lyx@rock-chips.com>

Merge branch 'linux-linaro-lsk-v4.4' into linux-linaro-lsk-v4.4-android

Conflicts:
arch/arm64/kernel/armv8_deprecated.c
arch/arm64/kernel/efi.c
arch/arm64/kernel/entry.S
arch/arm64/kernel/head.S
arch/arm64/kernel/hw_breakpoint.c
arch/arm64/mm/mmu.c
include/linux/memblock.h
mm/memblock.c

drm/rockchip: vop: fliter interlace mode

rk3288 and rk3368 are not support interlace mode

Change-Id: I5b6c155095285a5ae6e574efba122b56ddb1a112
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>

UPSTREAM: selinux: enable genfscon labeling for tracefs

In kernel version 4.1, tracefs was separated from debugfs into its
own filesystem. Prior to this split, files in
/sys/kernel/debug/tracing could be labeled during filesystem
creation using genfscon or later from userspace using setxattr. This
change re-enables support for genfscon labeling.

Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
(cherry picked from commit 6a3911837da0a90ed599fd0a9836472f5e7ddf1b)
Change-Id: I98ad8c829302346705c1abcdc8f019f479fdefb6
Bug: 62413700

UPSTREAM: drivers/perf: arm-pmu: fix RCU usage on pmu resume from low-power

(cherry picked from cbcc72e037b8a3eb1fad3c1ae22021df21c97a51)

Commit da4e4f18afe0 ("drivers/perf: arm_pmu: implement CPU_PM notifier")
added code in the arm perf infrastructure that allows the kernel to
save/restore perf counters whenever the CPU enters a low-power
state. The kernel saves/restores the counters for each active event
through the armpmu_{stop/start} ARM pmu API, so that the low-power state
enter/exit cycle is emulated through pmu start/stop operations for each
event in use.

However, calling armpmu_start() for each active event on power up
executes code that requires RCU locking (perf_event_update_userpage())
to be functional, so, given that the core may call the CPU_PM notifiers
while running the idle thread in an quiescent RCU state this is not
allowed as detected through the following splat when kernel is run with
CONFIG_PROVE_LOCKING enabled:

[   49.293286]
[   49.294761] ===============================
[   49.298895] [ INFO: suspicious RCU usage. ]
[   49.303031] 4.6.0-rc3+ #421 Not tainted
[   49.306821] -------------------------------
[   49.310956] include/linux/rcupdate.h:872 rcu_read_lock() used
illegally while idle!
[   49.318530]
[   49.318530] other info that might help us debug this:
[   49.318530]
[   49.326451]
[   49.326451] RCU used illegally from idle CPU!
[   49.326451] rcu_scheduler_active = 1, debug_locks = 0
[   49.337209] RCU used illegally from extended quiescent state!
[   49.342892] 2 locks held by swapper/2/0:
[   49.346768]  #0:  (cpu_pm_notifier_lock){......}, at:
[<ffffff8008163c28>] cpu_pm_exit+0x18/0x80
[   49.355492]  #1:  (rcu_read_lock){......}, at: [<ffffff800816dc38>]
perf_event_update_userpage+0x0/0x260

This patch wraps the armpmu_start() call (that indirectly calls
perf_event_update_userpage()) on CPU_PM notifier power state exit (or
failed entry) within the RCU_NONIDLE() macro so that the RCU subsystem
is made aware the calling cpu is not idle from an RCU perspective for
the armpmu_start() call duration, therefore fixing the issue.

Change-Id: I6352b3e7970a2116d23e258fa085f0c29982f789
Fixes: da4e4f18afe0 ("drivers/perf: arm_pmu: implement CPU_PM notifier")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: James Morse <james.morse@arm.com>
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

UPSTREAM: drivers/perf: arm_pmu: implement CPU_PM notifier

(cherry picked from commit da4e4f18afe0f3729d68f3785c5802f786d36e34)

When a CPU is suspended (either through suspend-to-RAM or CPUidle),
its PMU registers content can be lost, which means that counters
registers values that were initialized on power down entry have to be
reprogrammed on power-up to make sure the counters set-up is preserved
(ie on power-up registers take the reset values on Cold or Warm reset,
which can be architecturally UNKNOWN).

To guarantee seamless profiling conditions across a core power down
this patch adds a CPU PM notifier to ARM pmus, that upon CPU PM
entry/exit from low-power states saves/restores the pmu registers
set-up (by using the ARM perf API), so that the power-down/up cycle does
not affect the perf behaviour (apart from a black-out period between
power-up/down CPU PM notifications that is unavoidable).

Change-Id: Ifbd73b82ca9dc172c58e2488cda1af9af975b14f
Cc: Will Deacon <will.deacon@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

ANDROID: squashfs: Fix endianness issue

Code in squashfs_process_blocks was not correctly assigning
length. Casting to u16* introduced endianness issues on some
architectures.

Signed-off-by: Daniel Rosenberg <drosen@google.com>
Bug: 35257858
Change-Id: I9efaef4bc531b7469de79cf94738ade2dd6e6a8c

ANDROID: squashfs: Fix signed division issue

The value here can change depending on the type that PAGE_SIZE
has on a given architecture. To avoid the ensuing signed and
unsigned division conversions, we shift instead using PAGE_SHIFT

Signed-off-by: Daniel Rosenberg <drosen@google.com>
Bug: 35257858
Change-Id: I132cae93abea39390c3f0f91a4b2e026e97ed4c7

UPSTREAM: usb: gadget: f_fs: avoid out of bounds access on comp_desc

Companion descriptor is only used for SuperSpeed endpoints,
if the endpoints are HighSpeed or FullSpeed, the Companion
descriptor will not allocated, so we can only access it if
gadget is SuperSpeed.

I can reproduce this issue on Rockchip platform rk3368 SoC
which supports USB 2.0, and use functionfs for ADB. Kernel
build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report
the following BUG:

==================================================================
BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509
Read of size 1 by task swapper/0/0
============================================================================
BUG kmalloc-256 (Not tainted): kasan: bad access detected
----------------------------------------------------------------------------

Disabling lock debugging due to kernel taint
INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1
alloc_debug_processing+0x128/0x17c
___slab_alloc.constprop.58+0x50c/0x610
__slab_alloc.isra.55.constprop.57+0x24/0x34
__kmalloc+0xe0/0x250
ffs_func_bind+0x52c/0x99c
usb_add_function+0xd8/0x1d4
configfs_composite_bind+0x48c/0x570
udc_bind_to_driver+0x6c/0x170
usb_udc_attach_driver+0xa4/0xd0
gadget_dev_desc_UDC_store+0xcc/0x118
configfs_write_file+0x1a0/0x1f8
__vfs_write+0x64/0x174
vfs_write+0xe4/0x200
SyS_write+0x68/0xc8
el0_svc_naked+0x24/0x28
INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247
...
Call trace:
[<ffffff900808aab4>] dump_backtrace+0x0/0x230
[<ffffff900808acf8>] show_stack+0x14/0x1c
[<ffffff90084ad420>] dump_stack+0xa0/0xc8
[<ffffff90082157cc>] print_trailer+0x188/0x198
[<ffffff9008215948>] object_err+0x3c/0x4c
[<ffffff900821b5ac>] kasan_report+0x324/0x4dc
[<ffffff900821aa38>] __asan_load1+0x24/0x50
[<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0
[<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8
[<ffffff90089d7394>] android_setup+0x124/0x1a0
[<ffffff90089acd18>] _setup+0x54/0x74
[<ffffff90089b6b98>] handle_ep0+0x3288/0x4390
[<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4
[<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298
[<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20
[<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac
[<ffffff9008116610>] handle_irq_event+0x60/0xa0
[<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4
[<ffffff9008115568>] generic_handle_irq+0x30/0x40
[<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc
[<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4
...
Memory state around the buggy address:
  ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc
 >ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                       ^
  ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
  ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================

Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
(cherry picked from commit b7f73850bb4fac1e2209a4dd5e636d39be92f42c)

Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>

UPSTREAM: bpf: don't let ldimm64 leak map addresses on unprivileged

[ Upstream commit 0d0e57697f162da4aa218b5feafe614fb666db07 ]

The patch fixes two things at once:

1) It checks the env->allow_ptr_leaks and only prints the map address to
   the log if we have the privileges to do so, otherwise it just dumps 0
   as we would when kptr_restrict is enabled on %pK. Given the latter is
   off by default and not every distro sets it, I don't want to rely on
   this, hence the 0 by default for unprivileged.

2) Printing of ldimm64 in the verifier log is currently broken in that
   we don't print the full immediate, but only the 32 bit part of the
   first insn part for ldimm64. Thus, fix this up as well; it's okay to
   access, since we verified all ldimm64 earlier already (including just
   constants) through replace_map_fd_with_map_ptr().

Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs")
Fixes: cbd357008604 ("bpf: verifier (add ability to receive verification log)")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug: 62199770
Change-Id: I62ee47d06ddc669ba2863e8cf24f8f3e7683a461

BACKPORT: ext4: fix data exposure after a crash

Huang has reported that in his powerfail testing he is seeing stale
block contents in some of recently allocated blocks although he mounts
ext4 in data=ordered mode. After some investigation I have found out
that indeed when delayed allocation is used, we don't add inode to
transaction's list of inodes needing flushing before commit. Originally
we were doing that but commit f3b59291a69d removed the logic with a
flawed argument that it is not needed.

The problem is that although for delayed allocated blocks we write their
contents immediately after allocating them, there is no guarantee that
the IO scheduler or device doesn't reorder things and thus transaction
allocating blocks and attaching them to inode can reach stable storage
before actual block contents. Actually whenever we attach freshly
allocated blocks to inode using a written extent, we should add inode to
transaction's ordered inode list to make sure we properly wait for block
contents to be written before committing the transaction. So that is
what we do in this patch. This also handles other cases where stale data
exposure was possible - like filling hole via mmap in
data=ordered,nodelalloc mode.

The only exception to the above rule are extending direct IO writes where
blkdev_direct_IO() waits for IO to complete before increasing i_size and
thus stale data exposure is not possible. For now we don't complicate
the code with optimizing this special case since the overhead is pretty
low. In case this is observed to be a performance problem we can always
handle it using a special flag to ext4_map_blocks().

CC: stable@vger.kernel.org
Fixes: f3b59291a69d0b734be1fc8be489fef2dd846d3d
Reported-by: "HUANG Weller (CM/ESW12-CN)" <Weller.Huang@cn.bosch.com>
Tested-by: "HUANG Weller (CM/ESW12-CN)" <Weller.Huang@cn.bosch.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
(cherry picked from commit 06bd3c36a733ac27962fea7d6f47168841376824)
Signed-off-by: Connor O'Brien <connoro@google.com>
Bug: 62198330

Change-Id: Idc78b64e4f23e6085301c60057af6029b49a8193

power: rk818-charger: fix usb charger undetected

On some platforms (e.g. rk3399), we use extcon notify
framework to receive USB charger notifier from USB PHY
driver. Generally, the USB PHY driver uses a work to check
vbus status and the USB charger type every 2 seconds,
this polling mechanism may cause USB charger undetected
if we plug in/out USB charger quickly.

A typical error case is:
1. Plug in an USB DCP Adapter.
   - USB PHY driver sends notifier to rk818-charger
2. Plug out the USB Adapter, and plug in again immediately
   - rk818 detects plug out irq, and turns off charging
   - USB PHY driver schedule work doesn't detect the plug
     out/in operations, and doesn't send usb charger notifier

Fortunately, rk818 can detect plug in irq, so let's check
the USB charger type in rk818 plug in irq handler.

Change-Id: Iee45769c8a98c709da2dbfa514198ab0f648fd20
Signed-off-by: William Wu <william.wu@rock-chips.com>

UPSTREAM: drm: introduce pipe color correction properties

Patch based on a previous series by Shashank Sharma.

This introduces optional properties to enable color correction at the
pipe level. It relies on 3 transformations applied to every pixels
displayed. First a lookup into a degamma table, then a multiplication
of the rgb components by a 3x3 matrix and finally another lookup into
a gamma table.

The following properties can be added to a pipe :
  - DEGAMMA_LUT : blob containing degamma LUT
  - DEGAMMA_LUT_SIZE : number of elements in DEGAMMA_LUT
  - CTM : transformation matrix applied after the degamma LUT
  - GAMMA_LUT : blob containing gamma LUT
  - GAMMA_LUT_SIZE : number of elements in GAMMA_LUT

DEGAMMA_LUT_SIZE and GAMMA_LUT_SIZE are read only properties, set by
the driver to tell userspace applications what sizes should be the
lookup tables in DEGAMMA_LUT and GAMMA_LUT.

A helper is also provided so legacy gamma correction is redirected
through these new properties.

v2: Register LUT size properties as range

v3: Fix round in drm_color_lut_get_value() helper
    More docs on how degamma/gamma properties are used

v4: Update contributors

v5: Rename CTM_MATRIX property to CTM (Doh!)
    Add legacy gamma_set atomic helper
    Describe CTM/LUT acronyms in the kernel doc

v6: Fix missing blob unref in drm_atomic_helper_crtc_reset

Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Rob Bradford <robert.bradford@intel.com>
[danvet: CrOS maintainers are also happy with the userspacde side:
https://codereview.chromium.org/1182063002/ ]
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1456506302-640-4-git-send-email-lionel.g.landwerlin@intel.com
(cherry picked from commit 5488dc16fde74595a40c5d20ae52d978313f0b4e)

Change-Id: I8952fa72998b669cf6d8a7e120a72ffb225b1ba1
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>

UPSTREAM: GPU-DRM: Delete unnecessary checks before drm_property_unreference_blob()

The drm_property_unreference_blob() function tests whether its argument
is NULL and then returns immediately.
Thus the tests around the calls are not needed.

This issue was detected by using the Coccinelle software.

Link: http://patchwork.freedesktop.org/patch/msgid/563C8B3E.405@users.sourceforge.net
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 5f911905054a64cf8c7871fddd33f4af74f07a17)

Change-Id: I599721227294c7cde5fd4f2ef6d5a97212b61b77
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>

ARM: dts: rockchip: fix rk3288-android fiq-debugger irq

153 is arm pmu irq.

Change-Id: I18c00eb0cb10646b1b73535837ac26af196a3b51
Signed-off-by: Huang, Tao <huangtao@rock-chips.com>

ARM: dts: rk3288-evb: enable hs200 mode

Change-Id: I2a805198e2441a33f721a2b7167c99a180f1fc21
Signed-off-by: Steven Chen <cw@rock-chips.com>

rk_fiq_debugger: reset and init uart, if uart is abnormal

Change-Id: Idaa5d3d9ecd03325f3412a5b9e9b95eae20b0a22
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>

Merge remote-tracking branch 'origin/v4.4/topic/optee-lsk-mainline' into linux-linaro-lsk-v4.4

Conflicts:
compatiable issues in
arch/arm64/kernel/arm64ksyms.c
arch/arm64/kernel/asm-offsets.c
arch/arm64/kvm/hyp/fpsimd.S
drivers/firmware/psci.c

Documentation: tee subsystem and op-tee driver

Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
(cherry picked from commit 6a6e77006fcdba89708214556c6d560323e850fc)
Signed-off-by: Alex Shi <alex.shi@linaro.org>

tee: add OP-TEE driver

Adds a OP-TEE driver which also can be compiled as a loadable module.

* Targets ARM and ARM64
* Supports using reserved memory from OP-TEE as shared memory
* Probes OP-TEE version using SMCs
* Accepts requests on privileged and unprivileged device
* Uses OPTEE message protocol version 2 to communicate with secure world

Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org> (HiKey)
Tested-by: Volodymyr Babchuk <vlad.babchuk@gmail.com> (RCAR H3)
Tested-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
(cherry picked from commit 4fb0a5eb364d239722e745c02aef0dbd4e0f1ad2)
Signed-off-by: Alex Shi <alex.shi@linaro.org>

tee: generic TEE subsystem

Initial patch for generic TEE subsystem.
This subsystem provides:
* Registration/un-registration of TEE drivers.
* Shared memory between normal world and secure world.
* Ioctl interface for interaction with user space.
* Sysfs implementation_id of TEE driver

A TEE (Trusted Execution Environment) driver is a driver that interfaces
with a trusted OS running in some secure environment, for example,
TrustZone on ARM cpus, or a separate secure co-processor etc.

The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.

This patch builds on other similar implementations trying to solve
the same problem:
* "optee_linuxdriver" by among others
  Jean-michel DELORME<jean-michel.delorme@st.com> and
  Emmanuel MICHEL <emmanuel.michel@st.com>
* "Generic TrustZone Driver" by Javier González <javier@javigon.com>

Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org> (HiKey)
Tested-by: Volodymyr Babchuk <vlad.babchuk@gmail.com> (RCAR H3)
Tested-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
(cherry picked from commit 967c9cca2cc50569efc65945325c173cecba83bd)
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Conflicts:
remove fsi from drivers
drivers/Kconfig
drivers/Makefile

dt/bindings: add bindings for optee

Introduces linaro prefix and adds bindings for ARM TrustZone based OP-TEE
implementation.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
(cherry picked from commit c8bfafb1594435889b571b79325011e8b7fd087b)
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Conflicts:
Documentation/devicetree/bindings/vendor-prefixes.txt

kernel.h: add u64_to_user_ptr()

This function had copies in 3 different files. Unify them in kernel.h.

Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@intel.com> [drm/i915/]
Acked-by: Rob Clark <robdclark@gmail.com> [drm/msm/]
Acked-by: Lucas Stach <l.stach@pengutronix.de> [drm/etinav/]
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3ed605bc8a0a688d8750a1e2eff39c854418c5cf)
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Conflicts:
drop drivers/gpu/drm/etnaviv/etnaviv_gem_submit.c

ARM: 8481/2: drivers: psci: replace psci firmware calls

Switch to use a generic interface for issuing SMC/HVC based on ARM SMC
Calling Convention. Removes now the now unused psci-call.S.

Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit e679660dbb8347f275fe5d83a5dd59c1fb6c8e63)
Signed-off-by: Alex Shi <alex.shi@linaro.org>

ARM: 8480/2: arm64: add implementation for arm-smccc

Adds implementation for arm-smccc and enables CONFIG_HAVE_SMCCC.

Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit 14457459f9ca2ff8521686168ea179edc3a56a44)
Signed-off-by: Alex Shi <alex.shi@linaro.org>

ARM: 8479/2: add implementation for arm-smccc

Adds implementation for arm-smccc and enables CONFIG_HAVE_SMCCC for
architectures that may support arm-smccc. It's the responsibility of the
caller to know if the SMC instruction is supported by the platform.

Reviewed-by: Lars Persson <lars.persson@axis.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit b329f95d70f3f955093e9a2b18ac1ed3587a8f73)
Signed-off-by: Alex Shi <alex.shi@linaro.org>

ARM: 8478/2: arm/arm64: add arm-smccc

Adds helpers to do SMC and HVC based on ARM SMC Calling Convention.
CONFIG_HAVE_ARM_SMCCC is enabled for architectures that may support the
SMC or HVC instruction. It's the responsibility of the caller to know if
the SMC instruction is supported by the platform.

This patch doesn't provide an implementation of the declared functions.
Later patches will bring in implementations and set
CONFIG_HAVE_ARM_SMCCC for ARM and ARM64 respectively.

Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit 98dd64f34f47ce19b388d9015f767f48393a81eb)
Signed-off-by: Alex Shi <alex.shi@linaro.org>

arm64: dts: rockchip: fix the memory size of PX5 Evaluation board

Commit 122682b2abb6 ("arm64: dts: rockchip: Add PX5 Evaluation board")
sets the memory size to 2 GB, but this board only has 1 GB DRAM, so change
it to the correct value here.

Fixes: 122682b2abb6 ("arm64: dts: rockchip: Add PX5 Evaluation board")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
(cherry-picked from git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git
 commit 2f513bd9eac1a2642b40387d4f89c3987641e59b)

Change-Id: If6a64fa0eab3d76b90f122e63d30c1d7940b0a57
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>

arm64: dts: rockchip: add sdmmc support for px5-evb

px5-evb has one sdmmc slot, so we could support sdmmc.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
(cherry-picked from git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git
 commit 41a603b9337c412e5902091f5343f803b36b9995)

Change-Id: I3f4edbeefb39516d814d54b6583e2ada5505ab75
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>

arm64: dts: rockchip: Add more properties for emmc on px5-evb

The emmc on px5-evb can support hs200, so let's add mmc-hs200-1_8v.
And in order to speed up the boot time, we could add no-sdio and
no-sd to simplify the initialization.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
(cherry-picked from git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git
 commit 674c81cf2c22918e34a8b42b89aaf89247256b6d)

Change-Id: I2e72c7b2d6bc5da939068264ed90b2980ffdfabb
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>

arm64: dts: rockchip: Add PX5 Evaluation board

PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI/BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Conflicts:
Documentation/devicetree/bindings/arm/rockchip.txt
arch/arm64/boot/dts/rockchip/Makefile

(cherry-picked from git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git
 commit 76c923bb64923a387f0fc95480afb61ff1504eae)

Change-Id: I41212701d9bec3ce0864b995070439d4640bce28
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>

power_supply: Add support TI BQ25703 charger chip

Change-Id: I3689a9f108e6fb86db4800d47a3aa7da7f7010e7
Signed-off-by: shengfei Xu <xsf@rock-chips.com>

PM / devfreq: get lcdc type from vop drivers for rk3368

Change-Id: I9205286f7b4c0d7ecba3bb08a45af3f49225abe5
Signed-off-by: Tang Yun ping <typ@rock-chips.com>

Linux 4.4.76

KVM: nVMX: Fix exception injection

commit d4912215d1031e4fb3d1038d2e1857218dba0d0a upstream.

 WARNING: CPU: 3 PID: 2840 at arch/x86/kvm/vmx.c:10966 nested_vmx_vmexit+0xdcd/0xde0 [kvm_intel]
 CPU: 3 PID: 2840 Comm: qemu-system-x86 Tainted: G           OE   4.12.0-rc3+ #23
 RIP: 0010:nested_vmx_vmexit+0xdcd/0xde0 [kvm_intel]
 Call Trace:
  ? kvm_check_async_pf_completion+0xef/0x120 [kvm]
  ? rcu_read_lock_sched_held+0x79/0x80
  vmx_queue_exception+0x104/0x160 [kvm_intel]
  ? vmx_queue_exception+0x104/0x160 [kvm_intel]
  kvm_arch_vcpu_ioctl_run+0x1171/0x1ce0 [kvm]
  ? kvm_arch_vcpu_load+0x47/0x240 [kvm]
  ? kvm_arch_vcpu_load+0x62/0x240 [kvm]
  kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
  ? __fget+0xf3/0x210
  do_vfs_ioctl+0xa4/0x700
  ? __fget+0x114/0x210
  SyS_ioctl+0x79/0x90
  do_syscall_64+0x81/0x220
  entry_SYSCALL64_slow_path+0x25/0x25

This is triggered occasionally by running both win7 and win2016 in L2, in
addition, EPT is disabled on both L1 and L2. It can't be reproduced easily.

Commit 0b6ac343fc (KVM: nVMX: Correct handling of exception injection) mentioned
that "KVM wants to inject page-faults which it got to the guest. This function
assumes it is called with the exit reason in vmcs02 being a #PF exception".
Commit e011c663 (KVM: nVMX: Check all exceptions for intercept during delivery to
L2) allows to check all exceptions for intercept during delivery to L2. However,
there is no guarantee the exit reason is exception currently, when there is an
external interrupt occurred on host, maybe a time interrupt for host which should
not be injected to guest, and somewhere queues an exception, then the function
nested_vmx_check_exception() will be called and the vmexit emulation codes will
try to emulate the "Acknowledge interrupt on exit" behavior, the warning is
triggered.

Reusing the exit reason from the L2->L0 vmexit is wrong in this case,
the reason must always be EXCEPTION_NMI when injecting an exception into
L1 as a nested vmexit.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Fixes: e011c663b9c7 ("KVM: nVMX: Check all exceptions for intercept during delivery to L2")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: zero base3 of unusable segments

commit f0367ee1d64d27fa08be2407df5c125442e885e3 upstream.

Static checker noticed that base3 could be used uninitialized if the
segment was not present (useable).  Random stack values probably would
not pass VMCS entry checks.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 1aa366163b8b ("KVM: x86 emulator: consolidate segment accessors")
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86/vPMU: fix undefined shift in intel_pmu_refresh()

commit 34b0dadbdf698f9b277a31b2747b625b9a75ea1f upstream.

Static analysis noticed that pmu->nr_arch_gp_counters can be 32
(INTEL_PMC_MAX_GENERIC) and therefore cannot be used to shift 'int'.

I didn't add BUILD_BUG_ON for it as we have a better checker.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 25462f7f5295 ("KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch")
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: fix emulation of RSM and IRET instructions

commit 6ed071f051e12cf7baa1b69d3becb8f232fdfb7b upstream.

On AMD, the effect of set_nmi_mask called by emulate_iret_real and em_rsm
on hflags is reverted later on in x86_emulate_instruction where hflags are
overwritten with ctxt->emul_flags (the kvm_set_hflags call). This manifests
as a hang when rebooting Windows VMs with QEMU, OVMF, and >1 vcpu.

Instead of trying to merge ctxt->emul_flags into vcpu->arch.hflags after
an instruction is emulated, this commit deletes emul_flags altogether and
makes the emulator access vcpu->arch.hflags using two new accessors. This
way all changes, on the emulator side as well as in functions called from
the emulator and accessing vcpu state with emul_to_vcpu, are preserved.

More details on the bug and its manifestation with Windows and OVMF:

  It's a KVM bug in the interaction between SMI/SMM and NMI, specific to AMD.
  I believe that the SMM part explains why we started seeing this only with
  OVMF.

  KVM masks and unmasks NMI when entering and leaving SMM. When KVM emulates
  the RSM instruction in em_rsm, the set_nmi_mask call doesn't stick because
  later on in x86_emulate_instruction we overwrite arch.hflags with
  ctxt->emul_flags, effectively reverting the effect of the set_nmi_mask call.
  The AMD-specific hflag of interest here is HF_NMI_MASK.

  When rebooting the system, Windows sends an NMI IPI to all but the current
  cpu to shut them down. Only after all of them are parked in HLT will the
  initiating cpu finish the restart. If NMI is masked, other cpus never get
  the memo and the initiating cpu spins forever, waiting for
  hal!HalpInterruptProcessorsStarted to drop. That's the symptom we observe.

Fixes: a584539b24b8 ("KVM: x86: pass the whole hflags field to emulator and back")
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cpufreq: s3c2416: double free on driver init error path

commit a69261e4470d680185a15f748d9cdafb37c57a33 upstream.

The "goto err_armclk;" error path already does a clk_put(s3c_freq->hclk);
so this is a double free.

Fixes: 34ee55075265 ([CPUFREQ] Add S3C2416/S3C2450 cpufreq driver)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()

commit 73dbd4a4230216b6a5540a362edceae0c9b4876b upstream.

In function amd_iommu_bind_pasid(), the control flow jumps
to label out_free when pasid_state->mm and mm is NULL. And
mmput(mm) is called.  In function mmput(mm), mm is
referenced without validation. This will result in a NULL
dereference bug. This patch fixes the bug.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: f0aac63b873b ('iommu/amd: Don't hold a reference to mm_struct')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu: Handle default domain attach failure

commit 797a8b4d768c58caac58ee3e8cb36a164d1b7751 upstream.

We wouldn't normally expect ops->attach_dev() to fail, but on IOMMUs
with limited hardware resources, or generally misconfigured systems,
it is certainly possible. We report failure correctly from the external
iommu_attach_device() interface, but do not do so in iommu_group_add()
when attaching to the default domain. The result of failure there is
that the device, group and domain all get left in a broken,
part-configured state which leads to weird errors and misbehaviour down
the line when IOMMU API calls sort-of-but-don't-quite work.

Check the return value of __iommu_attach_device() on the default domain,
and refactor the error handling paths to cope with its failure and clean
up correctly in such cases.

Fixes: e39cb8a3aa98 ("iommu: Make sure a device is always attached to a domain")
Reported-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/vt-d: Don't over-free page table directories

commit f7116e115acdd74bc75a4daf6492b11d43505125 upstream.

dma_pte_free_level() recurses down the IOMMU page tables and frees
directory pages that are entirely contained in the given PFN range.
Unfortunately, it incorrectly calculates the starting address covered
by the PTE under consideration, which can lead to it clearing an entry
that is still in use.

This occurs if we have a scatterlist with an entry that has a length
greater than 1026 MB and is aligned to 2 MB for both the IOMMU and
physical addresses. For example, if __domain_mapping() is asked to map a
two-entry scatterlist with 2 MB and 1028 MB segments to PFN 0xffff80000,
it will ask if dma_pte_free_pagetable() is asked to PFNs from
0xffff80200 to 0xffffc05ff, it will also incorrectly clear the PFNs from
0xffff80000 to 0xffff801ff because of this issue. The current code will
set level_pfn to 0xffff80200, and 0xffff80200-0xffffc01ff fits inside
the range being cleared. Properly setting the level_pfn for the current
level under consideration catches that this PTE is outside of the range
being cleared.

This patch also changes the value passed into dma_pte_free_level() when
it recurses. This only affects the first PTE of the range being cleared,
and is handled by the existing code that ensures we start our cursor no
lower than start_pfn.

This was found when using dma_map_sg() to map large chunks of contiguous
memory, which immediatedly led to faults on the first access of the
erroneously-deleted mappings.

Fixes: 3269ee0bd668 ("intel-iommu: Fix leaks in pagetable freeing")
Reviewed-by: Benjamin Serebrin <serebrin@google.com>
Signed-off-by: David Dillow <dillow@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: o2hb: revert hb threshold to keep compatible

commit 33496c3c3d7b88dcbe5e55aa01288b05646c6aca upstream.

Configfs is the interface for ocfs2-tools to set configure to kernel and
$configfs_dir/cluster/$clustername/heartbeat/dead_threshold is the one
used to configure heartbeat dead threshold.  Kernel has a default value
of it but user can set O2CB_HEARTBEAT_THRESHOLD in /etc/sysconfig/o2cb
to override it.

Commit 45b997737a80 ("ocfs2/cluster: use per-attribute show and store
methods") changed heartbeat dead threshold name while ocfs2-tools did
not, so ocfs2-tools won't set this configurable and the default value is
always used.  So revert it.

Fixes: 45b997737a80 ("ocfs2/cluster: use per-attribute show and store methods")
Link: http://lkml.kernel.org/r/1490665245-15374-1-git-send-email-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mm: Fix flush_tlb_page() on Xen

commit dbd68d8e84c606673ebbcf15862f8c155fa92326 upstream.

flush_tlb_page() passes a bogus range to flush_tlb_others() and
expects the latter to fix it up.  native_flush_tlb_others() has the
fixup but Xen's version doesn't.  Move the fixup to
flush_tlb_others().

AFAICS the only real effect is that, without this fix, Xen would
flush everything instead of just the one page on remote vCPUs in
when flush_tlb_page() was called.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: e7b52ffd45a6 ("x86/flush_tlb: try flush_tlb_single one by one in flush_tlb_range")
Link: http://lkml.kernel.org/r/10ed0e4dfea64daef10b87fb85df1746999b4dba.1492844372.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mpx: Correctly report do_mpx_bt_fault() failures to user-space

commit 5ed386ec09a5d75bcf073967e55e895c2607a5c3 upstream.

When this function fails it just sends a SIGSEGV signal to
user-space using force_sig(). This signal is missing
essential information about the cause, e.g. the trap_nr or
an error code.

Fix this by propagating the error to the only caller of
mpx_handle_bd_fault(), do_bounds(), which sends the correct
SIGSEGV signal to the process.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: fe3d197f84319 ('x86, mpx: On-demand kernel allocation of bounds tables')
Link: http://lkml.kernel.org/r/1491488362-27198-1-git-send-email-joro@8bytes.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8685/1: ensure memblock-limit is pmd-aligned

commit 9e25ebfe56ece7541cd10a20d715cbdd148a2e06 upstream.

The pmd containing memblock_limit is cleared by prepare_page_table()
which creates the opportunity for early_alloc() to allocate unmapped
memory if memblock_limit is not pmd aligned causing a boot-time hang.

Commit 965278dcb8ab ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
attempted to resolve this problem, but there is a path through the
adjust_lowmem_bounds() routine where if all memory regions start and
end on pmd-aligned addresses the memblock_limit will be set to
arm_lowmem_limit.

Since arm_lowmem_limit can be affected by the vmalloc early parameter,
the value of arm_lowmem_limit may not be pmd-aligned. This commit
corrects this oversight such that memblock_limit is always rounded
down to pmd-alignment.

Fixes: 965278dcb8ab ("ARM: 8356/1: mm: handle non-pmd-aligned end of RAM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM64/ACPI: Fix BAD_MADT_GICC_ENTRY() macro implementation

commit cb7cf772d83d2d4e6995c5bb9e0fb59aea8f7080 upstream.

The BAD_MADT_GICC_ENTRY() macro checks if a GICC MADT entry passes
muster from an ACPI specification standpoint. Current macro detects the
MADT GICC entry length through ACPI firmware version (it changed from 76
to 80 bytes in the transition from ACPI 5.1 to ACPI 6.0 specification)
but always uses (erroneously) the ACPICA (latest) struct (ie struct
acpi_madt_generic_interrupt - that is 80-bytes long) length to check if
the current GICC entry memory record exceeds the MADT table end in
memory as defined by the MADT table header itself, which may result in
false negatives depending on the ACPI firmware version and how the MADT
entries are laid out in memory (ie on ACPI 5.1 firmware MADT GICC
entries are 76 bytes long, so by adding 80 to a GICC entry start address
in memory the resulting address may well be past the actual MADT end,
triggering a false negative).

Fix the BAD_MADT_GICC_ENTRY() macro by reshuffling the condition checks
and update them to always use the firmware version specific MADT GICC
entry length in order to carry out boundary checks.

Fixes: b6cfb277378e ("ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro")
Reported-by: Julien Grall <julien.grall@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Al Stone <ahs3@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/loadavg: Avoid loadavg spikes caused by delayed NO_HZ accounting

commit 6e5f32f7a43f45ee55c401c0b9585eb01f9629a8 upstream.

If we crossed a sample window while in NO_HZ we will add LOAD_FREQ to
the pending sample window time on exit, setting the next update not
one window into the future, but two.

This situation on exiting NO_HZ is described by:

  this_rq->calc_load_update < jiffies < calc_load_update

In this scenario, what we should be doing is:

  this_rq->calc_load_update = calc_load_update      [ next window ]

But what we actually do is:

  this_rq->calc_load_update = calc_load_update + LOAD_FREQ   [ next+1 window ]

This has the effect of delaying load average updates for potentially
up to ~9seconds.

This can result in huge spikes in the load average values due to
per-cpu uninterruptible task counts being out of sync when accumulated
across all CPUs.

It's safe to update the per-cpu active count if we wake between sample
windows because any load that we left in 'calc_load_idle' will have
been zero'd when the idle load was folded in calc_global_load().

This issue is easy to reproduce before,

  commit 9d89c257dfb9 ("sched/fair: Rewrite runnable load and utilization average tracking")

just by forking short-lived process pipelines built from ps(1) and
grep(1) in a loop. I'm unable to reproduce the spikes after that
commit, but the bug still seems to be present from code review.

Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Fixes: commit 5167e8d ("sched/nohz: Rewrite and fix load-avg computation -- again")
Link: http://lkml.kernel.org/r/20170217120731.11868-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: bcm281xx: Fix use of uninitialized spinlock.

commit fedf266f9955d9a019643cde199a2fd9a0259f6f upstream.

The bcm_kona_wdt_set_resolution_reg() call takes the spinlock, so
initialize it earlier.  Fixes a warning at boot with lock debugging
enabled.

Fixes: 6adb730dc208 ("watchdog: bcm281xx: Watchdog Driver")
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: Oops on error in pfkey_msg2xfrm_state()

commit 1e3d0c2c70cd3edb5deed186c5f5c75f2b84a633 upstream.

There are some missing error codes here so we accidentally return NULL
instead of an error pointer.  It results in a NULL pointer dereference.

Fixes: df71837d5024 ("[LSM-IPSec]: Security association restriction.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: NULL dereference on allocation failure

commit e747f64336fc15e1c823344942923195b800aa1e upstream.

The default error code in pfkey_msg2xfrm_state() is -ENOBUFS.  We
added a new call to security_xfrm_state_alloc() which sets "err" to zero
so there several places where we can return ERR_PTR(0) if kmalloc()
fails.  The caller is expecting error pointers so it leads to a NULL
dereference.

Fixes: df71837d5024 ("[LSM-IPSec]: Security association restriction.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: fix stack access out of bounds with CONFIG_XFRM_SUB_POLICY

commit 9b3eb54106cf6acd03f07cf0ab01c13676a226c2 upstream.

When CONFIG_XFRM_SUB_POLICY=y, xfrm_dst stores a copy of the flowi for
that dst. Unfortunately, the code that allocates and fills this copy
doesn't care about what type of flowi (flowi, flowi4, flowi6) gets
passed. In multiple code paths (from raw_sendmsg, from TCP when
replying to a FIN, in vxlan, geneve, and gre), the flowi that gets
passed to xfrm is actually an on-stack flowi4, so we end up reading
stuff from the stack past the end of the flowi4 struct.

Since xfrm_dst->origin isn't used anywhere following commit
ca116922afa8 ("xfrm: Eliminate "fl" and "pol" args to
xfrm_bundle_ok()."), just get rid of it.  xfrm_dst->partner isn't used
either, so get rid of that too.

Fixes: 9d6ec938019c ("ipv4: Use flowi4 in public route lookup interfaces.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

jump label: fix passing kbuild_cflags when checking for asm goto support

commit 7292ae3d5a18fb922be496e6bb687647193569b4 upstream.

The latest change of asm goto support check added passing of KBUILD_CFLAGS
to compiler.  When these flags reference gcc plugins that are not built yet,
the check fails.

When one runs "make bzImage" followed by "make modules", the kernel is always
built with HAVE_JUMP_LABEL disabled, while the modules are built depending on
CONFIG_JUMP_LABEL.  If HAVE_JUMP_LABEL macro happens to be different, modules
are built with undefined references, e.g.:

ERROR: "static_key_slow_inc" [net/netfilter/xt_TEE.ko] undefined!
ERROR: "static_key_slow_dec" [net/netfilter/xt_TEE.ko] undefined!
ERROR: "static_key_slow_dec" [net/netfilter/nft_meta.ko] undefined!
ERROR: "static_key_slow_inc" [net/netfilter/nft_meta.ko] undefined!
ERROR: "nf_hooks_needed" [net/netfilter/ipvs/ip_vs.ko] undefined!
ERROR: "nf_hooks_needed" [net/ipv6/ipv6.ko] undefined!
ERROR: "static_key_count" [net/ipv6/ipv6.ko] undefined!
ERROR: "static_key_slow_inc" [net/ipv6/ipv6.ko] undefined!

This change moves the check before all these references are added
to KBUILD_CFLAGS.  This is correct because subsequent KBUILD_CFLAGS
modifications are not relevant to this check.

Reported-by: Anton V. Boyarshinov <boyarsh@altlinux.org>
Fixes: 35f860f9ba6a ("jump label: pass kbuild_cflags when checking for asm goto support")
Signed-off-by: Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: David Lin <dtwlin@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ravb: Fix use-after-free on `ifconfig eth0 down`

[ Upstream commit 79514ef670e9e575a1fe36922268c439d0f0ca8a ]

Commit a47b70ea86bd ("ravb: unmap descriptors when freeing rings") has
introduced the issue seen in [1] reproduced on H3ULCB board.

Fix this by relocating the RX skb ringbuffer free operation, so that
swiotlb page unmapping can be done first. Freeing of aligned TX buffers
is not relevant to the issue seen in [1]. Still, reposition TX free
calls as well, to have all kfree() operations performed consistently
_after_ dma_unmap_*()/dma_free_*().

[1] Console screenshot with the problem reproduced:

salvator-x login: root
root@salvator-x:~# ifconfig eth0 up
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: \
       attached PHY driver [Micrel KSZ9031 Gigabit PHY]   \
       (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=235)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
root@salvator-x:~#
root@salvator-x:~# ifconfig eth0 down

==================================================================
BUG: KASAN: use-after-free in swiotlb_tbl_unmap_single+0xc4/0x35c
Write of size 1538 at addr ffff8006d884f780 by task ifconfig/1649

CPU: 0 PID: 1649 Comm: ifconfig Not tainted 4.12.0-rc4-00004-g112eb07287d1 #32
Hardware name: Renesas H3ULCB board based on r8a7795 (DT)
Call trace:
[<ffff20000808f11c>] dump_backtrace+0x0/0x3a4
[<ffff20000808f4d4>] show_stack+0x14/0x1c
[<ffff20000865970c>] dump_stack+0xf8/0x150
[<ffff20000831f8b0>] print_address_description+0x7c/0x330
[<ffff200008320010>] kasan_report+0x2e0/0x2f4
[<ffff20000831eac0>] check_memory_region+0x20/0x14c
[<ffff20000831f054>] memcpy+0x48/0x68
[<ffff20000869ed50>] swiotlb_tbl_unmap_single+0xc4/0x35c
[<ffff20000869fcf4>] unmap_single+0x90/0xa4
[<ffff20000869fd14>] swiotlb_unmap_page+0xc/0x14
[<ffff2000080a2974>] __swiotlb_unmap_page+0xcc/0xe4
[<ffff2000088acdb8>] ravb_ring_free+0x514/0x870
[<ffff2000088b25dc>] ravb_close+0x288/0x36c
[<ffff200008aaf8c4>] __dev_close_many+0x14c/0x174
[<ffff200008aaf9b4>] __dev_close+0xc8/0x144
[<ffff200008ac2100>] __dev_change_flags+0xd8/0x194
[<ffff200008ac221c>] dev_change_flags+0x60/0xb0
[<ffff200008ba2dec>] devinet_ioctl+0x484/0x9d4
[<ffff200008ba7b78>] inet_ioctl+0x190/0x194
[<ffff200008a78c44>] sock_do_ioctl+0x78/0xa8
[<ffff200008a7a128>] sock_ioctl+0x110/0x3c4
[<ffff200008365a70>] vfs_ioctl+0x90/0xa0
[<ffff200008365dbc>] do_vfs_ioctl+0x148/0xc38
[<ffff2000083668f0>] SyS_ioctl+0x44/0x74
[<ffff200008083770>] el0_svc_naked+0x24/0x28

The buggy address belongs to the page:
page:ffff7e001b6213c0 count:0 mapcount:0 mapping:          (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: 0000000000000000 ffff7e001b6213e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8006d884f680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
 ffff8006d884f700: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff8006d884f780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
                   ^
 ffff8006d884f800: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
 ffff8006d884f880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
Disabling lock debugging due to kernel taint
root@salvator-x:~#

Fixes: a47b70ea86bd ("ravb: unmap descriptors when freeing rings")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sctp: check af before verify address in sctp_addr_id2transport

[ Upstream commit 912964eacb111551db73429719eb5fadcab0ff8a ]

Commit 6f29a1306131 ("sctp: sctp_addr_id2transport should verify the
addr before looking up assoc") invoked sctp_verify_addr to verify the
addr.

But it didn't check af variable beforehand, once users pass an address
with family = 0 through sockopt, sctp_get_af_specific will return NULL
and NULL pointer dereference will be caused by af->sockaddr_len.

This patch is to fix it by returning NULL if af variable is NULL.

Fixes: 6f29a1306131 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_core: Eliminate warning messages for SRQ_LIMIT under SRIOV

[ Upstream commit 9577b174cd0323d287c994ef0891db71666d0765 ]

When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.

Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.

Fixes: acba2420f9d2 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9cb50d ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf probe: Fix to show correct locations for events on modules

[ Upstream commit d2d4edbebe07ddb77980656abe7b9bc7a9e0cdf7 ]

Fix to show correct locations for events on modules by relocating given
address instead of retrying after failure.

This happens when the module text size is big enough, bigger than
sh_addr, because the original code retries with given address + sh_addr
if it failed to find CU DIE at the given address.

Any address smaller than sh_addr always fails and it retries with the
correct address, but addresses bigger than sh_addr will get a CU DIE
which is on the given address (not adjusted by sh_addr).

In my environment(x86-64), the sh_addr of ".text" section is 0x10030.
Since i915 is a huge kernel module, we can see this issue as below.

  $ grep "[Tt] .*\[i915\]" /proc/kallsyms | sort | head -n1
  ffffffffc0270000 t i915_switcheroo_can_switch [i915]

ffffffffc0270000 + 0x10030 = ffffffffc0280030, so we'll check
symbols cross this boundary.

  $ grep "[Tt] .*\[i915\]" /proc/kallsyms | grep -B1 ^ffffffffc028\
  | head -n 2
  ffffffffc027ff80 t haswell_init_clock_gating [i915]
  ffffffffc0280110 t valleyview_init_clock_gating [i915]

So setup probes on both function and see what happen.

  $ sudo ./perf probe -m i915 -a haswell_init_clock_gating \
        -a valleyview_init_clock_gating
  Added new events:
    probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
    probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)

  You can now use it in all perf tools, such as:

   perf record -e probe:valleyview_init_clock_gating -aR sleep 1

  $ sudo ./perf probe -l
    probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
    probe:valleyview_init_clock_gating (on i915_vga_set_decode:4@gpu/drm/i915/i915_drv.c in i915)

As you can see, haswell_init_clock_gating is correctly shown,
but valleyview_init_clock_gating is not.

With this patch, both events are shown correctly.

  $ sudo ./perf probe -l
    probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
    probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)

Committer notes:

In my case:

  # perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
  Added new events:
    probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
    probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)

  You can now use it in all perf tools, such as:

  perf record -e probe:valleyview_init_clock_gating -aR sleep 1

  # perf probe -l
    probe:haswell_init_clock_gating (on i915_getparam+432@gpu/drm/i915/i915_drv.c in i915)
    probe:valleyview_init_clock_gating (on __i915_printk+240@gpu/drm/i915/i915_drv.c in i915)
  #

  # readelf -SW /lib/modules/4.9.0+/build/vmlinux | egrep -w '.text|Name'
   [Nr] Name   Type      Address          Off    Size   ES Flg Lk Inf Al
   [ 1] .text  PROGBITS  ffffffff81000000 200000 822fd3 00  AX  0   0 4096
  #

  So both are b0rked, now with the fix:

  # perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
  Added new events:
    probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
    probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)

  You can now use it in all perf tools, such as:

perf record -e probe:valleyview_init_clock_gating -aR sleep 1

  # perf probe -l
    probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
    probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
  #

Both looks correct.

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411436777.9978.1440275861947194930.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

be2net: fix status check in be_cmd_pmac_add()

[ Upstream commit fe68d8bfe59c561664aa87d827aa4b320eb08895 ]

Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.

Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/ctl_reg: make __ctl_load a full memory barrier

[ Upstream commit e991c24d68b8c0ba297eeb7af80b1e398e98c33f ]

We have quite a lot of code that depends on the order of the
__ctl_load inline assemby and subsequent memory accesses, like
e.g. disabling lowcore protection and the writing to lowcore.

Since the __ctl_load macro does not have memory barrier semantics, nor
any other dependencies the compiler is, theoretically, free to shuffle
code around. Or in other words: storing to lowcore could happen before
lowcore protection is disabled.

In order to avoid this class of potential bugs simply add a full
memory barrier to the __ctl_load macro.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

swiotlb: ensure that page-sized mappings are page-aligned

[ Upstream commit 602d9858f07c72eab64f5f00e2fae55f9902cfbe ]

Some drivers do depend on page mappings to be page aligned.

Swiotlb already enforces such alignment for mappings greater than page,
extend that to page-sized mappings as well.

Without this fix, nvme hits BUG() in nvme_setup_prps(), because that routine
assumes page-aligned mappings.

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coredump: Ensure proper size of sparse core files

[ Upstream commit 4d22c75d4c7b5c5f4bd31054f09103ee490878fd ]

If the last section of a core file ends with an unmapped or zero page,
the size of the file does not correspond with the last dump_skip() call.
gdb complains that the file is truncated and can be confusing to users.

After all of the vma sections are written, make sure that the file size
is no smaller than the current file position.

This problem can be demonstrated with gdb's bigcore testcase on the
sparc architecture.

Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mpx: Use compatible types in comparison to fix sparse error

[ Upstream commit 453828625731d0ba7218242ef6ec88f59408f368 ]

info->si_addr is of type void __user *, so it should be compared against
something from the same address space.

This fixes the following sparse error:

  arch/x86/mm/mpx.c:296:27: error: incompatible types in comparison expression (different address spaces)

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: initialize SMPS field in HT capabilities

[ Upstream commit 43071d8fb3b7f589d72663c496a6880fb097533c ]

ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.

This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.

Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.

Reported-by: Elektra Wagenrad <onelektra@gmx.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: davinci: use dma_mapping_error()

[ Upstream commit c5a2a394835f473ae23931eda5066d3771d7b2f8 ]

The correct error checking for dma_map_single() is to use
dma_mapping_error().

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: avoid double free of resource identifiers

[ Upstream commit cd60be4916ae689387d04b86b6fc15931e4c95ae ]

Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to
NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset()
attempts to free the memory again.

Signed-off-by: Roberto Sassu <rsassu@suse.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: i2c-hid: Add sleep between POWER ON and RESET

[ Upstream commit a89af4abdf9b353cdd6f61afc0eaaac403304873 ]

Support for the Asus Touchpad was recently added. It turns out this
device can fail initialisation (and become unusable) when the RESET
command is sent too soon after the POWER ON command.

Unfortunately the i2c-hid specification does not specify the need for
a delay between these two commands. But it was discovered the Windows
driver has a 1ms delay.

As a result, this patch modifies the i2c-hid module to add a sleep
inbetween the POWER ON and RESET commands which lasts between 1ms and 5ms.

See https://github.com/vlasenko/hid-asus-dkms/issues/24 for further
details.

Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/panic.c: add missing \n

[ Upstream commit ff7a28a074ccbea999dadbb58c46212cf90984c6 ]

When a system panics, the "Rebooting in X seconds.." message is never
printed because it lacks a new line.  Fix it.

Link: http://lkml.kernel.org/r/20170119114751.2724-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmveth: Add a proper check for the availability of the checksum features

[ Upstream commit 23d28a859fb847fd7fcfbd31acb3b160abb5d6ae ]

When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:

 ibmveth 71000003 (unregistered net_device): unable to change
 checksum offload settings. 1 rc=-2 ret_attr=71000003

This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.

Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vxlan: do not age static remote mac entries

[ Upstream commit efb5f68f32995c146944a9d4257c3cf8eae2c4a1 ]

Mac aging is applicable only for dynamically learnt remote mac
entries. Check for user configured static remote mac entries
and skip aging.

Signed-off-by: Balakrishnan Raman <ramanb@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_net: fix PAGE_SIZE > 64k

[ Upstream commit d0fa28f00052391b5df328f502fbbdd4444938b7 ]

I don't have any guests with PAGE_SIZE > 64k but the
code seems to be clearly broken in that case
as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need
more than 8 bit and so the code in mergeable_ctx_to_buf_address
does not give us the actual true size.

Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfio/spapr: fail tce_iommu_attach_group() when iommu_data is null

[ Upstream commit bd00fdf198e2da475a2f4265a83686ab42d998a8 ]

The recently added mediated VFIO driver doesn't know about powerpc iommu.
It thus doesn't register a struct iommu_table_group in the iommu group
upon device creation. The iommu_data pointer hence remains null.

This causes a kernel oops when userspace tries to set the iommu type of a
container associated with a mediated device to VFIO_SPAPR_TCE_v2_IOMMU.

[   82.585440] mtty mtty: MDEV: Registered
[   87.655522] iommu: Adding device 83b8f4f2-509f-382f-3c1e-e6bfe0fa1001 to group 10
[   87.655527] vfio_mdev 83b8f4f2-509f-382f-3c1e-e6bfe0fa1001: MDEV: group_id = 10
[  116.297184] Unable to handle kernel paging request for data at address 0x00000030
[  116.297389] Faulting instruction address: 0xd000000007870524
[  116.297465] Oops: Kernel access of bad area, sig: 11 [#1]
[  116.297611] SMP NR_CPUS=2048
[  116.297611] NUMA
[  116.297627] PowerNV
...
[  116.297954] CPU: 33 PID: 7067 Comm: qemu-system-ppc Not tainted 4.10.0-rc5-mdev-test #8
[  116.297993] task: c000000e7718b680 task.stack: c000000e77214000
[  116.298025] NIP: d000000007870524 LR: d000000007870518 CTR: 0000000000000000
[  116.298064] REGS: c000000e77217990 TRAP: 0300   Not tainted  (4.10.0-rc5-mdev-test)
[  116.298103] MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE>
[  116.298107]   CR: 84004444  XER: 00000000
[  116.298154] CFAR: c00000000000888c DAR: 0000000000000030 DSISR: 40000000 SOFTE: 1
               GPR00: d000000007870518 c000000e77217c10 d00000000787b0ed c000000eed2103c0
               GPR04: 0000000000000000 0000000000000000 c000000eed2103e0 0000000f24320000
               GPR08: 0000000000000104 0000000000000001 0000000000000000 d0000000078729b0
               GPR12: c00000000025b7e0 c00000000fe08400 0000000000000001 000001002d31d100
               GPR16: 000001002c22c850 00003ffff315c750 0000000043145680 0000000043141bc0
               GPR20: ffffffffffffffed fffffffffffff000 0000000020003b65 d000000007706018
               GPR24: c000000f16cf0d98 d000000007706000 c000000003f42980 c000000003f42980
               GPR28: c000000f1575ac00 c000000003f429c8 0000000000000000 c000000eed2103c0
[  116.298504] NIP [d000000007870524] tce_iommu_attach_group+0x10c/0x360 [vfio_iommu_spapr_tce]
[  116.298555] LR [d000000007870518] tce_iommu_attach_group+0x100/0x360 [vfio_iommu_spapr_tce]
[  116.298601] Call Trace:
[  116.298610] [c000000e77217c10] [d000000007870518] tce_iommu_attach_group+0x100/0x360 [vfio_iommu_spapr_tce] (unreliable)
[  116.298671] [c000000e77217cb0] [d0000000077033a0] vfio_fops_unl_ioctl+0x278/0x3e0 [vfio]
[  116.298713] [c000000e77217d40] [c0000000002a3ebc] do_vfs_ioctl+0xcc/0x8b0
[  116.298745] [c000000e77217de0] [c0000000002a4700] SyS_ioctl+0x60/0xc0
[  116.298782] [c000000e77217e30] [c00000000000b220] system_call+0x38/0xfc
[  116.298812] Instruction dump:
[  116.298828] 7d3f4b78 409effc8 3d220000 e9298020 3c800140 38a00018 608480c0 e8690028
[  116.298869] 4800249d e8410018 7c7f1b79 41820230 <e93e0030> 2fa90000 419e0114 e9090020
[  116.298914] ---[ end trace 1e10b0ced08b9120 ]---

This patch fixes the oops.

Reported-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: check ring being ready before using

[ Upstream commit c5f21c9f878b8dcd54d0b9739c025ca73cb4c091 ]

Return success when the ring is properly initialized, otherwise return
failure.

Tonga SRIOV VF doesn't have UVD and VCE engines, the initialization of
these IPs is bypassed. The system crashes if application submit IB to
their rings which are not ready to use. It could be a common issue if
IP having ring buffer is disabled for some reason on specific ASIC, so
it should check the ring being ready to use.

Bug: amdgpu_test crashes system on Tonga VF.

Signed-off-by: Ding Pixel <Pixel.Ding@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: Check return value of phy_connect_direct()

[ Upstream commit 4078b76cac68e50ccf1f76a74e7d3d5788aec3fe ]

We need to check the return value of phy_connect_direct() in
dsa_slave_phy_connect() otherwise we may be continuing the
initialization of a slave network device with a PHY that already
attached somewhere else and which will soon be in error because the PHY
device is in error.

The conditions for such an error to occur are that we have a port of our
switch that is not disabled, and has the same port number as a PHY
address (say both 5) that can be probed using the DSA slave MII bus. We
end-up having this slave network device find a PHY at the same address
as our port number, and we try to attach to it.

A slave network (e.g: port 0) has already attached to our PHY device,
and we try to re-attach it with a different network device, but since we
ignore the error we would end-up initializating incorrect device
references by the time the slave network interface is opened.

The code has been (re)organized several times, making it hard to provide
an exact Fixes tag, this is a bugfix nonetheless.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

amd-xgbe: Check xgbe_init() return code

[ Upstream commit 738f7f647371ff4cfc9646c99dba5b58ad142db3 ]

The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: ideapad-laptop: handle ACPI event 1

[ Upstream commit cfee5d63767b2e7997c1f36420d008abbe61565c ]

On Ideapad laptops, ACPI event 1 is currently not handled. Many models
log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while
running on battery power. Some convertible laptops receive this event
when switching in and out of tablet mode.

This adds and additional case for event 1 in ideapad_acpi_notify to call
ideapad_input_report(priv, vpc_bit), so that the event is reported to
userspace and we avoid unnecessary logging.

Fixes bug #107481 (https://bugzilla.kernel.org/show_bug.cgi?id=107481)
Fixes bug #65751 (https://bugzilla.kernel.org/show_bug.cgi?id=65751)

Signed-off-by: Zach Ploskey <zach@ploskey.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: virtio_scsi: Reject commands when virtqueue is broken

[ Upstream commit 773c7220e22d193e5667c352fcbf8d47eefc817f ]

In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally.  Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed.  Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.

 [   17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache
 [   17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
 [   21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
 [   21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0

However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host.  The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.

That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either.  The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there.  The
calling sequence provides a bit of distinction for us:

  virtscsi_queuecommand()
   -> virtscsi_kick_cmd()
    -> virtscsi_add_cmd()
     -> virtqueue_add_sgs()
      -> virtqueue_add()
         if success
           return 0
         elseif vq->broken or vring_mapping_error()
           return -EIO
         else
           return -ENOSPC

A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two.  But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully.  The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):

 [   22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
 [   22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
 [   22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache
 [   22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK

I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.

Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-netfront: Fix Rx stall during network stress and OOM

[ Upstream commit 90c311b0eeead647b708a723dbdde1eda3dcad05 ]

During an OOM scenario, request slots could not be created as skb
allocation fails. So the netback cannot pass in packets and netfront
wrongly assumes that there is no more work to be done and it disables
polling. This causes Rx to stall.

The issue is with the retry logic which schedules the timer if the
created slots are less than NET_RX_SLOTS_MIN. The count of new request
slots to be pushed are calculated as a difference between new req_prod
and rsp_cons which could be more than the actual slots, if there are
unconsumed responses.

The fix is to calculate the count of newly created slots as the
difference between new req_prod and old req_prod.

Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

swiotlb-xen: update dev_addr after swapping pages

[ Upstream commit f1225ee4c8fcf09afaa199b8b1f0450f38b8cd11 ]

In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original
page is not suitable, we swap it for another page from the swiotlb
pool.

In these cases, we don't update the previously calculated dma address
for the page before calling xen_dma_map_page. Thus, we end up calling
xen_dma_map_page passing the wrong dev_addr, resulting in
xen_dma_map_page mistakenly assuming that the page is foreign when it is
local.

Fix the bug by updating dev_addr appropriately.

This change has no effect on x86, because xen_dma_map_page is a stub
there.

Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Tested-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio_console: fix a crash in config_work_handler

[ Upstream commit 8379cadf71c3ee8173a1c6fc1ea7762a9638c047 ]

Using control_work instead of config_work as the 3rd argument to
container_of results in an invalid portdev pointer. Indeed, the work
structure is initialized as below:

    INIT_WORK(&portdev->config_work, &config_work_handler);

It leads to a crash when portdev->vdev is dereferenced later. This
bug
is triggered when the guest uses a virtio-console without multiport
feature and receives a config_changed virtio interrupt.

Signed-off-by: G. Campana <gcampana@quarkslab.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: fix truncate down when no_holes feature is enabled

[ Upstream commit 91298eec05cd8d4e828cf7ee5d4a6334f70cf69a ]

For such a file mapping,

[0-4k][hole][8k-12k]

In NO_HOLES mode, we don't have the [hole] extent any more.
Commit c1aa45759e90 ("Btrfs: fix shrinking truncate when the no_holes feature is enabled")
 fixed disk isize not being updated in NO_HOLES mode when data is not flushed.

However, even if data has been flushed, we can still have trouble
in updating disk isize since we updated disk isize to 'start' of
the last evicted extent.

Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gianfar: Do not reuse pages from emergency reserve

[ Upstream commit 69fed99baac186013840ced3524562841296034f ]

A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.

Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.

This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.

Fixes: 75354148ce69 ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/eeh: Enable IO path on permanent error

[ Upstream commit 387bbc974f6adf91aa635090f73434ed10edd915 ]

We give up recovery on permanent error, simply shutdown the affected
devices and remove them. If the devices can't be put into quiet state,
they spew more traffic that is likely to cause another unexpected EEH
error. This was observed on "p8dtu2u" machine:

   0002:00:00.0 PCI bridge: IBM Device 03dc
   0002:01:00.0 Ethernet controller: Intel Corporation \
                Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
   0002:01:00.1 Ethernet controller: Intel Corporation \
                Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
   0002:01:00.2 Ethernet controller: Intel Corporation \
                Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
   0002:01:00.3 Ethernet controller: Intel Corporation \
                Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)

On P8 PowerNV platform, the IO path is frozen when shutdowning the
devices, meaning the memory registers are inaccessible. It is why
the devices can't be put into quiet state before removing them.
This fixes the issue by enabling IO path prior to putting the devices
into quiet state.

Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bgmac: Remove superflous netif_carrier_on()

commit 3894396e64994f31c3ef5c7e6f63dded0593e567 upstream.

bgmac_open() calls phy_start() to initialize the PHY state machine,
which will set the interface's carrier state accordingly, no need to
force that as this could be conflicting with the PHY state determined by
PHYLIB.

Fixes: dd4544f05469 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bgmac: Start transmit queue in bgmac_open

commit c3897f2a69e54dd113fc9abd2daf872e5b495798 upstream.

The driver does not start the transmit queue in bgmac_open(). If the
queue was stopped prior to closing then re-opening the interface, we
would never be able to wake-up again.

Fixes: dd4544f05469 ("bgmac: driver for GBit MAC core on BCMA bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>