From 13a80cb8b72769f163834d4243bd156f1bec37dc Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Thu, 10 Jan 2013 19:19:43 -0500 Subject: [PATCH] drivers/net: delete at1700 ISA 10Mbit driver These Fujitsu MB86965 based ISA 10Mbit cards were another of the relatively rare cards dating from the early 1990s that for one reason or another didn't seem to get a lot of use in linux. So we retire it now with a reasonable degree of confidence that it won't impact anyone. Signed-off-by: Paul Gortmaker --- drivers/net/Space.c | 4 - drivers/net/ethernet/fujitsu/Kconfig | 12 - drivers/net/ethernet/fujitsu/Makefile | 1 - drivers/net/ethernet/fujitsu/at1700.c | 791 -------------------------- 4 files changed, 808 deletions(-) delete mode 100644 drivers/net/ethernet/fujitsu/at1700.c diff --git a/drivers/net/Space.c b/drivers/net/Space.c index 4141c6465683..e7d916d5232e 100644 --- a/drivers/net/Space.c +++ b/drivers/net/Space.c @@ -44,7 +44,6 @@ extern struct net_device *el2_probe(int unit); extern struct net_device *ne_probe(int unit); extern struct net_device *hp_probe(int unit); extern struct net_device *hp_plus_probe(int unit); -extern struct net_device *at1700_probe(int unit); extern struct net_device *fmv18x_probe(int unit); extern struct net_device *eth16i_probe(int unit); extern struct net_device *i82596_probe(int unit); @@ -140,9 +139,6 @@ static struct devprobe2 isa_probes[] __initdata = { {cs89x0_probe, 0}, #endif #endif -#ifdef CONFIG_AT1700 - {at1700_probe, 0}, -#endif #ifdef CONFIG_ETH16I {eth16i_probe, 0}, /* ICL EtherTeam 16i/32 */ #endif diff --git a/drivers/net/ethernet/fujitsu/Kconfig b/drivers/net/ethernet/fujitsu/Kconfig index aca156888fd8..af114fd51141 100644 --- a/drivers/net/ethernet/fujitsu/Kconfig +++ b/drivers/net/ethernet/fujitsu/Kconfig @@ -17,18 +17,6 @@ config NET_VENDOR_FUJITSU if NET_VENDOR_FUJITSU -config AT1700 - tristate "AT1700/1720 support (EXPERIMENTAL)" - depends on ISA && EXPERIMENTAL - select CRC32 - ---help--- - If you have a network (Ethernet) card of this type, say Y and read - the Ethernet-HOWTO, available from - . - - To compile this driver as a module, choose M here. The module - will be called at1700. - config PCMCIA_FMVJ18X tristate "Fujitsu FMV-J18x PCMCIA support" depends on PCMCIA diff --git a/drivers/net/ethernet/fujitsu/Makefile b/drivers/net/ethernet/fujitsu/Makefile index 2730ae67d3aa..e54d0af771d0 100644 --- a/drivers/net/ethernet/fujitsu/Makefile +++ b/drivers/net/ethernet/fujitsu/Makefile @@ -2,6 +2,5 @@ # Makefile for the Fujitsu network device drivers. # -obj-$(CONFIG_AT1700) += at1700.o obj-$(CONFIG_ETH16I) += eth16i.o obj-$(CONFIG_PCMCIA_FMVJ18X) += fmvj18x_cs.o diff --git a/drivers/net/ethernet/fujitsu/at1700.c b/drivers/net/ethernet/fujitsu/at1700.c deleted file mode 100644 index 4b80dc4531ad..000000000000 --- a/drivers/net/ethernet/fujitsu/at1700.c +++ /dev/null @@ -1,791 +0,0 @@ -/* at1700.c: A network device driver for the Allied Telesis AT1700. - - Written 1993-98 by Donald Becker. - - Copyright 1993 United States Government as represented by the - Director, National Security Agency. - - This software may be used and distributed according to the terms - of the GNU General Public License, incorporated herein by reference. - - The author may be reached as becker@scyld.com, or C/O - Scyld Computing Corporation - 410 Severn Ave., Suite 210 - Annapolis MD 21403 - - This is a device driver for the Allied Telesis AT1700, and - Fujitsu FMV-181/182/181A/182A/183/184/183A/184A, which are - straight-forward Fujitsu MB86965 implementations. - - Modification for Fujitsu FMV-18X cards is done by Yutaka Tamiya - (tamy@flab.fujitsu.co.jp). - - Sources: - The Fujitsu MB86965 datasheet. - - After the initial version of this driver was written Gerry Sawkins of - ATI provided their EEPROM configuration code header file. - Thanks to NIIBE Yutaka for bug fixes. - - MCA bus (AT1720) support (now deleted) by Rene Schmit - - Bugs: - The MB86965 has a design flaw that makes all probes unreliable. Not - only is it difficult to detect, it also moves around in I/O space in - response to inb()s from other device probes! -*/ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -static char version[] __initdata = - "at1700.c:v1.16 9/11/06 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n"; - -#define DRV_NAME "at1700" - -/* Tunable parameters. */ - -/* When to switch from the 64-entry multicast filter to Rx-all-multicast. */ -#define MC_FILTERBREAK 64 - -/* These unusual address orders are used to verify the CONFIG register. */ - -static int fmv18x_probe_list[] __initdata = { - 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x300, 0x340, 0 -}; - -/* - * ISA - */ - -static unsigned at1700_probe_list[] __initdata = { - 0x260, 0x280, 0x2a0, 0x240, 0x340, 0x320, 0x380, 0x300, 0 -}; - -/* use 0 for production, 1 for verification, >2 for debug */ -#ifndef NET_DEBUG -#define NET_DEBUG 1 -#endif -static unsigned int net_debug = NET_DEBUG; - -typedef unsigned char uchar; - -/* Information that need to be kept for each board. */ -struct net_local { - spinlock_t lock; - unsigned char mc_filter[8]; - uint jumpered:1; /* Set iff the board has jumper config. */ - uint tx_started:1; /* Packets are on the Tx queue. */ - uint tx_queue_ready:1; /* Tx queue is ready to be sent. */ - uint rx_started:1; /* Packets are Rxing. */ - uchar tx_queue; /* Number of packet on the Tx queue. */ - ushort tx_queue_len; /* Current length of the Tx queue. */ -}; - - -/* Offsets from the base address. */ -#define STATUS 0 -#define TX_STATUS 0 -#define RX_STATUS 1 -#define TX_INTR 2 /* Bit-mapped interrupt enable registers. */ -#define RX_INTR 3 -#define TX_MODE 4 -#define RX_MODE 5 -#define CONFIG_0 6 /* Misc. configuration settings. */ -#define CONFIG_1 7 -/* Run-time register bank 2 definitions. */ -#define DATAPORT 8 /* Word-wide DMA or programmed-I/O dataport. */ -#define TX_START 10 -#define COL16CNTL 11 /* Control Reg for 16 collisions */ -#define MODE13 13 -#define RX_CTRL 14 -/* Configuration registers only on the '865A/B chips. */ -#define EEPROM_Ctrl 16 -#define EEPROM_Data 17 -#define CARDSTATUS 16 /* FMV-18x Card Status */ -#define CARDSTATUS1 17 /* FMV-18x Card Status */ -#define IOCONFIG 18 /* Either read the jumper, or move the I/O. */ -#define IOCONFIG1 19 -#define SAPROM 20 /* The station address PROM, if no EEPROM. */ -#define MODE24 24 -#define RESET 31 /* Write to reset some parts of the chip. */ -#define AT1700_IO_EXTENT 32 -#define PORT_OFFSET(o) (o) - - -#define TX_TIMEOUT (HZ/10) - - -/* Index to functions, as function prototypes. */ - -static int at1700_probe1(struct net_device *dev, int ioaddr); -static int read_eeprom(long ioaddr, int location); -static int net_open(struct net_device *dev); -static netdev_tx_t net_send_packet(struct sk_buff *skb, - struct net_device *dev); -static irqreturn_t net_interrupt(int irq, void *dev_id); -static void net_rx(struct net_device *dev); -static int net_close(struct net_device *dev); -static void set_rx_mode(struct net_device *dev); -static void net_tx_timeout (struct net_device *dev); - - -/* Check for a network adaptor of this type, and return '0' iff one exists. - If dev->base_addr == 0, probe all likely locations. - If dev->base_addr == 1, always return failure. - If dev->base_addr == 2, allocate space for the device and return success - (detachable devices only). - */ - -static int io = 0x260; - -static int irq; - -static void cleanup_card(struct net_device *dev) -{ - free_irq(dev->irq, NULL); - release_region(dev->base_addr, AT1700_IO_EXTENT); -} - -struct net_device * __init at1700_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(sizeof(struct net_local)); - unsigned *port; - int err = 0; - - if (!dev) - return ERR_PTR(-ENODEV); - - if (unit >= 0) { - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - io = dev->base_addr; - irq = dev->irq; - } else { - dev->base_addr = io; - dev->irq = irq; - } - - if (io > 0x1ff) { /* Check a single specified location. */ - err = at1700_probe1(dev, io); - } else if (io != 0) { /* Don't probe at all. */ - err = -ENXIO; - } else { - for (port = at1700_probe_list; *port; port++) { - if (at1700_probe1(dev, *port) == 0) - break; - dev->irq = irq; - } - if (!*port) - err = -ENODEV; - } - if (err) - goto out; - err = register_netdev(dev); - if (err) - goto out1; - return dev; -out1: - cleanup_card(dev); -out: - free_netdev(dev); - return ERR_PTR(err); -} - -static const struct net_device_ops at1700_netdev_ops = { - .ndo_open = net_open, - .ndo_stop = net_close, - .ndo_start_xmit = net_send_packet, - .ndo_set_rx_mode = set_rx_mode, - .ndo_tx_timeout = net_tx_timeout, - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -/* The Fujitsu datasheet suggests that the NIC be probed for by checking its - "signature", the default bit pattern after a reset. This *doesn't* work -- - there is no way to reset the bus interface without a complete power-cycle! - - It turns out that ATI came to the same conclusion I did: the only thing - that can be done is checking a few bits and then diving right into an - EEPROM read. */ - -static int __init at1700_probe1(struct net_device *dev, int ioaddr) -{ - static const char fmv_irqmap[4] = {3, 7, 10, 15}; - static const char fmv_irqmap_pnp[8] = {3, 4, 5, 7, 9, 10, 11, 15}; - static const char at1700_irqmap[8] = {3, 4, 5, 9, 10, 11, 14, 15}; - unsigned int i, irq, is_fmv18x = 0, is_at1700 = 0; - int ret = -ENODEV; - struct net_local *lp = netdev_priv(dev); - - if (!request_region(ioaddr, AT1700_IO_EXTENT, DRV_NAME)) - return -EBUSY; - - /* Resetting the chip doesn't reset the ISA interface, so don't bother. - That means we have to be careful with the register values we probe - for. - */ -#ifdef notdef - printk("at1700 probe at %#x, eeprom is %4.4x %4.4x %4.4x ctrl %4.4x.\n", - ioaddr, read_eeprom(ioaddr, 4), read_eeprom(ioaddr, 5), - read_eeprom(ioaddr, 6), inw(ioaddr + EEPROM_Ctrl)); -#endif - /* We must check for the EEPROM-config boards first, else accessing - IOCONFIG0 will move the board! */ - if (at1700_probe_list[inb(ioaddr + IOCONFIG1) & 0x07] == ioaddr && - read_eeprom(ioaddr, 4) == 0x0000 && - (read_eeprom(ioaddr, 5) & 0xff00) == 0xF400) - is_at1700 = 1; - else if (inb(ioaddr + SAPROM ) == 0x00 && - inb(ioaddr + SAPROM + 1) == 0x00 && - inb(ioaddr + SAPROM + 2) == 0x0e) - is_fmv18x = 1; - else { - goto err_out; - } - - /* Reset the internal state machines. */ - outb(0, ioaddr + RESET); - - if (is_at1700) { - irq = at1700_irqmap[(read_eeprom(ioaddr, 12)&0x04) - | (read_eeprom(ioaddr, 0)>>14)]; - } else { - /* Check PnP mode for FMV-183/184/183A/184A. */ - /* This PnP routine is very poor. IO and IRQ should be known. */ - if (inb(ioaddr + CARDSTATUS1) & 0x20) { - irq = dev->irq; - for (i = 0; i < 8; i++) { - if (irq == fmv_irqmap_pnp[i]) - break; - } - if (i == 8) { - goto err_out; - } - } else { - if (fmv18x_probe_list[inb(ioaddr + IOCONFIG) & 0x07] != ioaddr) - goto err_out; - irq = fmv_irqmap[(inb(ioaddr + IOCONFIG)>>6) & 0x03]; - } - } - - printk("%s: %s found at %#3x, IRQ %d, address ", dev->name, - is_at1700 ? "AT1700" : "FMV-18X", ioaddr, irq); - - dev->base_addr = ioaddr; - dev->irq = irq; - - if (is_at1700) { - for(i = 0; i < 3; i++) { - unsigned short eeprom_val = read_eeprom(ioaddr, 4+i); - ((unsigned short *)dev->dev_addr)[i] = ntohs(eeprom_val); - } - } else { - for(i = 0; i < 6; i++) { - unsigned char val = inb(ioaddr + SAPROM + i); - dev->dev_addr[i] = val; - } - } - printk("%pM", dev->dev_addr); - - /* The EEPROM word 12 bit 0x0400 means use regular 100 ohm 10baseT signals, - rather than 150 ohm shielded twisted pair compensation. - 0x0000 == auto-sense the interface - 0x0800 == use TP interface - 0x1800 == use coax interface - */ - { - const char *porttype[] = {"auto-sense", "10baseT", "auto-sense", "10base2"}; - if (is_at1700) { - ushort setup_value = read_eeprom(ioaddr, 12); - dev->if_port = setup_value >> 8; - } else { - ushort setup_value = inb(ioaddr + CARDSTATUS); - switch (setup_value & 0x07) { - case 0x01: /* 10base5 */ - case 0x02: /* 10base2 */ - dev->if_port = 0x18; break; - case 0x04: /* 10baseT */ - dev->if_port = 0x08; break; - default: /* auto-sense */ - dev->if_port = 0x00; break; - } - } - printk(" %s interface.\n", porttype[(dev->if_port>>3) & 3]); - } - - /* Set the configuration register 0 to 32K 100ns. byte-wide memory, 16 bit - bus access, two 4K Tx queues, and disabled Tx and Rx. */ - outb(0xda, ioaddr + CONFIG_0); - - /* Set the station address in bank zero. */ - outb(0x00, ioaddr + CONFIG_1); - for (i = 0; i < 6; i++) - outb(dev->dev_addr[i], ioaddr + PORT_OFFSET(8 + i)); - - /* Switch to bank 1 and set the multicast table to accept none. */ - outb(0x04, ioaddr + CONFIG_1); - for (i = 0; i < 8; i++) - outb(0x00, ioaddr + PORT_OFFSET(8 + i)); - - - /* Switch to bank 2 */ - /* Lock our I/O address, and set manual processing mode for 16 collisions. */ - outb(0x08, ioaddr + CONFIG_1); - outb(dev->if_port, ioaddr + MODE13); - outb(0x00, ioaddr + COL16CNTL); - - if (net_debug) - printk(version); - - dev->netdev_ops = &at1700_netdev_ops; - dev->watchdog_timeo = TX_TIMEOUT; - - spin_lock_init(&lp->lock); - - lp->jumpered = is_fmv18x; - /* Snarf the interrupt vector now. */ - ret = request_irq(irq, net_interrupt, 0, DRV_NAME, dev); - if (ret) { - printk(KERN_ERR "AT1700 at %#3x is unusable due to a " - "conflict on IRQ %d.\n", - ioaddr, irq); - goto err_out; - } - - return 0; - -err_out: - release_region(ioaddr, AT1700_IO_EXTENT); - return ret; -} - - -/* EEPROM_Ctrl bits. */ -#define EE_SHIFT_CLK 0x40 /* EEPROM shift clock, in reg. 16. */ -#define EE_CS 0x20 /* EEPROM chip select, in reg. 16. */ -#define EE_DATA_WRITE 0x80 /* EEPROM chip data in, in reg. 17. */ -#define EE_DATA_READ 0x80 /* EEPROM chip data out, in reg. 17. */ - -/* The EEPROM commands include the alway-set leading bit. */ -#define EE_WRITE_CMD (5 << 6) -#define EE_READ_CMD (6 << 6) -#define EE_ERASE_CMD (7 << 6) - -static int __init read_eeprom(long ioaddr, int location) -{ - int i; - unsigned short retval = 0; - long ee_addr = ioaddr + EEPROM_Ctrl; - long ee_daddr = ioaddr + EEPROM_Data; - int read_cmd = location | EE_READ_CMD; - - /* Shift the read command bits out. */ - for (i = 9; i >= 0; i--) { - short dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0; - outb(EE_CS, ee_addr); - outb(dataval, ee_daddr); - outb(EE_CS | EE_SHIFT_CLK, ee_addr); /* EEPROM clock tick. */ - } - outb(EE_DATA_WRITE, ee_daddr); - for (i = 16; i > 0; i--) { - outb(EE_CS, ee_addr); - outb(EE_CS | EE_SHIFT_CLK, ee_addr); - retval = (retval << 1) | ((inb(ee_daddr) & EE_DATA_READ) ? 1 : 0); - } - - /* Terminate the EEPROM access. */ - outb(EE_CS, ee_addr); - outb(EE_SHIFT_CLK, ee_addr); - outb(0, ee_addr); - return retval; -} - - - -static int net_open(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - /* Set the configuration register 0 to 32K 100ns. byte-wide memory, 16 bit - bus access, and two 4K Tx queues. */ - outb(0x5a, ioaddr + CONFIG_0); - - /* Powerup, switch to register bank 2, and enable the Rx and Tx. */ - outb(0xe8, ioaddr + CONFIG_1); - - lp->tx_started = 0; - lp->tx_queue_ready = 1; - lp->rx_started = 0; - lp->tx_queue = 0; - lp->tx_queue_len = 0; - - /* Turn on hardware Tx and Rx interrupts. */ - outb(0x82, ioaddr + TX_INTR); - outb(0x81, ioaddr + RX_INTR); - - /* Enable the IRQ on boards of fmv18x it is feasible. */ - if (lp->jumpered) { - outb(0x80, ioaddr + IOCONFIG1); - } - - netif_start_queue(dev); - return 0; -} - -static void net_tx_timeout (struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - printk ("%s: transmit timed out with status %04x, %s?\n", dev->name, - inw (ioaddr + STATUS), inb (ioaddr + TX_STATUS) & 0x80 - ? "IRQ conflict" : "network cable problem"); - printk ("%s: timeout registers: %04x %04x %04x %04x %04x %04x %04x %04x.\n", - dev->name, inw(ioaddr + TX_STATUS), inw(ioaddr + TX_INTR), inw(ioaddr + TX_MODE), - inw(ioaddr + CONFIG_0), inw(ioaddr + DATAPORT), inw(ioaddr + TX_START), - inw(ioaddr + MODE13 - 1), inw(ioaddr + RX_CTRL)); - dev->stats.tx_errors++; - /* ToDo: We should try to restart the adaptor... */ - outw(0xffff, ioaddr + MODE24); - outw (0xffff, ioaddr + TX_STATUS); - outb (0x5a, ioaddr + CONFIG_0); - outb (0xe8, ioaddr + CONFIG_1); - outw (0x8182, ioaddr + TX_INTR); - outb (0x00, ioaddr + TX_START); - outb (0x03, ioaddr + COL16CNTL); - - dev->trans_start = jiffies; /* prevent tx timeout */ - - lp->tx_started = 0; - lp->tx_queue_ready = 1; - lp->rx_started = 0; - lp->tx_queue = 0; - lp->tx_queue_len = 0; - - netif_wake_queue(dev); -} - - -static netdev_tx_t net_send_packet (struct sk_buff *skb, - struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - short length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN; - short len = skb->len; - unsigned char *buf = skb->data; - static u8 pad[ETH_ZLEN]; - - netif_stop_queue (dev); - - /* We may not start transmitting unless we finish transferring - a packet into the Tx queue. During executing the following - codes we possibly catch a Tx interrupt. Thus we flag off - tx_queue_ready, so that we prevent the interrupt routine - (net_interrupt) to start transmitting. */ - lp->tx_queue_ready = 0; - { - outw (length, ioaddr + DATAPORT); - /* Packet data */ - outsw (ioaddr + DATAPORT, buf, len >> 1); - /* Check for dribble byte */ - if (len & 1) { - outw(skb->data[skb->len-1], ioaddr + DATAPORT); - len++; - } - /* Check for packet padding */ - if (length != skb->len) - outsw(ioaddr + DATAPORT, pad, (length - len + 1) >> 1); - - lp->tx_queue++; - lp->tx_queue_len += length + 2; - } - lp->tx_queue_ready = 1; - - if (lp->tx_started == 0) { - /* If the Tx is idle, always trigger a transmit. */ - outb (0x80 | lp->tx_queue, ioaddr + TX_START); - lp->tx_queue = 0; - lp->tx_queue_len = 0; - lp->tx_started = 1; - netif_start_queue (dev); - } else if (lp->tx_queue_len < 4096 - 1502) - /* Yes, there is room for one more packet. */ - netif_start_queue (dev); - dev_kfree_skb (skb); - - return NETDEV_TX_OK; -} - -/* The typical workload of the driver: - Handle the network interface interrupts. */ -static irqreturn_t net_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - struct net_local *lp; - int ioaddr, status; - int handled = 0; - - if (dev == NULL) { - printk ("at1700_interrupt(): irq %d for unknown device.\n", irq); - return IRQ_NONE; - } - - ioaddr = dev->base_addr; - lp = netdev_priv(dev); - - spin_lock (&lp->lock); - - status = inw(ioaddr + TX_STATUS); - outw(status, ioaddr + TX_STATUS); - - if (net_debug > 4) - printk("%s: Interrupt with status %04x.\n", dev->name, status); - if (lp->rx_started == 0 && - (status & 0xff00 || (inb(ioaddr + RX_MODE) & 0x40) == 0)) { - /* Got a packet(s). - We cannot execute net_rx more than once at the same time for - the same device. During executing net_rx, we possibly catch a - Tx interrupt. Thus we flag on rx_started, so that we prevent - the interrupt routine (net_interrupt) to dive into net_rx - again. */ - handled = 1; - lp->rx_started = 1; - outb(0x00, ioaddr + RX_INTR); /* Disable RX intr. */ - net_rx(dev); - outb(0x81, ioaddr + RX_INTR); /* Enable RX intr. */ - lp->rx_started = 0; - } - if (status & 0x00ff) { - handled = 1; - if (status & 0x02) { - /* More than 16 collisions occurred */ - if (net_debug > 4) - printk("%s: 16 Collision occur during Txing.\n", dev->name); - /* Cancel sending a packet. */ - outb(0x03, ioaddr + COL16CNTL); - dev->stats.collisions++; - } - if (status & 0x82) { - dev->stats.tx_packets++; - /* The Tx queue has any packets and is not being - transferred a packet from the host, start - transmitting. */ - if (lp->tx_queue && lp->tx_queue_ready) { - outb(0x80 | lp->tx_queue, ioaddr + TX_START); - lp->tx_queue = 0; - lp->tx_queue_len = 0; - dev->trans_start = jiffies; - netif_wake_queue (dev); - } else { - lp->tx_started = 0; - netif_wake_queue (dev); - } - } - } - - spin_unlock (&lp->lock); - return IRQ_RETVAL(handled); -} - -/* We have a good packet(s), get it/them out of the buffers. */ -static void -net_rx(struct net_device *dev) -{ - int ioaddr = dev->base_addr; - int boguscount = 5; - - while ((inb(ioaddr + RX_MODE) & 0x40) == 0) { - ushort status = inw(ioaddr + DATAPORT); - ushort pkt_len = inw(ioaddr + DATAPORT); - - if (net_debug > 4) - printk("%s: Rxing packet mode %02x status %04x.\n", - dev->name, inb(ioaddr + RX_MODE), status); -#ifndef final_version - if (status == 0) { - outb(0x05, ioaddr + RX_CTRL); - break; - } -#endif - - if ((status & 0xF0) != 0x20) { /* There was an error. */ - dev->stats.rx_errors++; - if (status & 0x08) dev->stats.rx_length_errors++; - if (status & 0x04) dev->stats.rx_frame_errors++; - if (status & 0x02) dev->stats.rx_crc_errors++; - if (status & 0x01) dev->stats.rx_over_errors++; - } else { - /* Malloc up new buffer. */ - struct sk_buff *skb; - - if (pkt_len > 1550) { - printk("%s: The AT1700 claimed a very large packet, size %d.\n", - dev->name, pkt_len); - /* Prime the FIFO and then flush the packet. */ - inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT); - outb(0x05, ioaddr + RX_CTRL); - dev->stats.rx_errors++; - break; - } - skb = netdev_alloc_skb(dev, pkt_len + 3); - if (skb == NULL) { - printk("%s: Memory squeeze, dropping packet (len %d).\n", - dev->name, pkt_len); - /* Prime the FIFO and then flush the packet. */ - inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT); - outb(0x05, ioaddr + RX_CTRL); - dev->stats.rx_dropped++; - break; - } - skb_reserve(skb,2); - - insw(ioaddr + DATAPORT, skb_put(skb,pkt_len), (pkt_len + 1) >> 1); - skb->protocol=eth_type_trans(skb, dev); - netif_rx(skb); - dev->stats.rx_packets++; - dev->stats.rx_bytes += pkt_len; - } - if (--boguscount <= 0) - break; - } - - /* If any worth-while packets have been received, dev_rint() - has done a mark_bh(NET_BH) for us and will work on them - when we get to the bottom-half routine. */ - { - int i; - for (i = 0; i < 20; i++) { - if ((inb(ioaddr + RX_MODE) & 0x40) == 0x40) - break; - inw(ioaddr + DATAPORT); /* dummy status read */ - outb(0x05, ioaddr + RX_CTRL); - } - - if (net_debug > 5) - printk("%s: Exint Rx packet with mode %02x after %d ticks.\n", - dev->name, inb(ioaddr + RX_MODE), i); - } -} - -/* The inverse routine to net_open(). */ -static int net_close(struct net_device *dev) -{ - struct net_local *lp = netdev_priv(dev); - int ioaddr = dev->base_addr; - - netif_stop_queue(dev); - - /* Set configuration register 0 to disable Tx and Rx. */ - outb(0xda, ioaddr + CONFIG_0); - - /* No statistic counters on the chip to update. */ - - /* Disable the IRQ on boards of fmv18x where it is feasible. */ - if (lp->jumpered) - outb(0x00, ioaddr + IOCONFIG1); - - /* Power-down the chip. Green, green, green! */ - outb(0x00, ioaddr + CONFIG_1); - return 0; -} - -/* - Set the multicast/promiscuous mode for this adaptor. -*/ - -static void -set_rx_mode(struct net_device *dev) -{ - int ioaddr = dev->base_addr; - struct net_local *lp = netdev_priv(dev); - unsigned char mc_filter[8]; /* Multicast hash filter */ - unsigned long flags; - - if (dev->flags & IFF_PROMISC) { - memset(mc_filter, 0xff, sizeof(mc_filter)); - outb(3, ioaddr + RX_MODE); /* Enable promiscuous mode */ - } else if (netdev_mc_count(dev) > MC_FILTERBREAK || - (dev->flags & IFF_ALLMULTI)) { - /* Too many to filter perfectly -- accept all multicasts. */ - memset(mc_filter, 0xff, sizeof(mc_filter)); - outb(2, ioaddr + RX_MODE); /* Use normal mode. */ - } else if (netdev_mc_empty(dev)) { - memset(mc_filter, 0x00, sizeof(mc_filter)); - outb(1, ioaddr + RX_MODE); /* Ignore almost all multicasts. */ - } else { - struct netdev_hw_addr *ha; - - memset(mc_filter, 0, sizeof(mc_filter)); - netdev_for_each_mc_addr(ha, dev) { - unsigned int bit = - ether_crc_le(ETH_ALEN, ha->addr) >> 26; - mc_filter[bit >> 3] |= (1 << bit); - } - outb(0x02, ioaddr + RX_MODE); /* Use normal mode. */ - } - - spin_lock_irqsave (&lp->lock, flags); - if (memcmp(mc_filter, lp->mc_filter, sizeof(mc_filter))) { - int i; - int saved_bank = inw(ioaddr + CONFIG_0); - /* Switch to bank 1 and set the multicast table. */ - outw((saved_bank & ~0x0C00) | 0x0480, ioaddr + CONFIG_0); - for (i = 0; i < 8; i++) - outb(mc_filter[i], ioaddr + PORT_OFFSET(8 + i)); - memcpy(lp->mc_filter, mc_filter, sizeof(mc_filter)); - outw(saved_bank, ioaddr + CONFIG_0); - } - spin_unlock_irqrestore (&lp->lock, flags); -} - -#ifdef MODULE -static struct net_device *dev_at1700; - -module_param(io, int, 0); -module_param(irq, int, 0); -module_param(net_debug, int, 0); -MODULE_PARM_DESC(io, "AT1700/FMV18X I/O base address"); -MODULE_PARM_DESC(irq, "AT1700/FMV18X IRQ number"); -MODULE_PARM_DESC(net_debug, "AT1700/FMV18X debug level (0-6)"); - -static int __init at1700_module_init(void) -{ - if (io == 0) - printk("at1700: You should not use auto-probing with insmod!\n"); - dev_at1700 = at1700_probe(-1); - if (IS_ERR(dev_at1700)) - return PTR_ERR(dev_at1700); - return 0; -} - -static void __exit at1700_module_exit(void) -{ - unregister_netdev(dev_at1700); - cleanup_card(dev_at1700); - free_netdev(dev_at1700); -} -module_init(at1700_module_init); -module_exit(at1700_module_exit); -#endif /* MODULE */ -MODULE_LICENSE("GPL"); -- 2.34.1