From 430400b86304ea729ba10f2966a8af67da60a37f Mon Sep 17 00:00:00 2001 From: Urs Fleisch Date: Fri, 7 Jan 2011 07:15:39 +0000 Subject: [PATCH] hwmon: driver for Sensirion SHT21 humidity and temperature sensor Signed-off-by: Urs Fleisch Acked-by: Jonathan Cameron Signed-off-by: Guenter Roeck --- Documentation/hwmon/sht21 | 49 ++++++ drivers/hwmon/Kconfig | 10 ++ drivers/hwmon/Makefile | 1 + drivers/hwmon/sht21.c | 307 ++++++++++++++++++++++++++++++++++++++ 4 files changed, 367 insertions(+) create mode 100644 Documentation/hwmon/sht21 create mode 100644 drivers/hwmon/sht21.c diff --git a/Documentation/hwmon/sht21 b/Documentation/hwmon/sht21 new file mode 100644 index 000000000000..db17fda45c3e --- /dev/null +++ b/Documentation/hwmon/sht21 @@ -0,0 +1,49 @@ +Kernel driver sht21 +=================== + +Supported chips: + * Sensirion SHT21 + Prefix: 'sht21' + Addresses scanned: none + Datasheet: Publicly available at the Sensirion website + http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT21.pdf + + * Sensirion SHT25 + Prefix: 'sht21' + Addresses scanned: none + Datasheet: Publicly available at the Sensirion website + http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT25.pdf + +Author: + Urs Fleisch + +Description +----------- + +The SHT21 and SHT25 are humidity and temperature sensors in a DFN package of +only 3 x 3 mm footprint and 1.1 mm height. The difference between the two +devices is the higher level of precision of the SHT25 (1.8% relative humidity, +0.2 degree Celsius) compared with the SHT21 (2.0% relative humidity, +0.3 degree Celsius). + +The devices communicate with the I2C protocol. All sensors are set to the same +I2C address 0x40, so an entry with I2C_BOARD_INFO("sht21", 0x40) can be used +in the board setup code. + +sysfs-Interface +--------------- + +temp1_input - temperature input +humidity1_input - humidity input + +Notes +----- + +The driver uses the default resolution settings of 12 bit for humidity and 14 +bit for temperature, which results in typical measurement times of 22 ms for +humidity and 66 ms for temperature. To keep self heating below 0.1 degree +Celsius, the device should not be active for more than 10% of the time, +e.g. maximum two measurements per second at the given resolution. + +Different resolutions, the on-chip heater, using the CRC checksum and reading +the serial number are not supported yet. diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index a56f6adf3b76..0f09567257fd 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -734,6 +734,16 @@ config SENSORS_SHT15 This driver can also be built as a module. If so, the module will be called sht15. +config SENSORS_SHT21 + tristate "Sensiron humidity and temperature sensors. SHT21 and compat." + depends on I2C + help + If you say yes here you get support for the Sensiron SHT21, SHT25 + humidity and temperature sensors. + + This driver can also be built as a module. If so, the module + will be called sht21. + config SENSORS_S3C tristate "Samsung built-in ADC" depends on S3C_ADC diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 2479b3da272c..20e74086e681 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -90,6 +90,7 @@ obj-$(CONFIG_SENSORS_PC87427) += pc87427.o obj-$(CONFIG_SENSORS_PCF8591) += pcf8591.o obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o obj-$(CONFIG_SENSORS_SHT15) += sht15.o +obj-$(CONFIG_SENSORS_SHT21) += sht21.o obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o obj-$(CONFIG_SENSORS_SMM665) += smm665.o obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o diff --git a/drivers/hwmon/sht21.c b/drivers/hwmon/sht21.c new file mode 100644 index 000000000000..1c8c9812f244 --- /dev/null +++ b/drivers/hwmon/sht21.c @@ -0,0 +1,307 @@ +/* Sensirion SHT21 humidity and temperature sensor driver + * + * Copyright (C) 2010 Urs Fleisch + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA + * + * Data sheet available (5/2010) at + * http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT21.pdf + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* I2C command bytes */ +#define SHT21_TRIG_T_MEASUREMENT_HM 0xe3 +#define SHT21_TRIG_RH_MEASUREMENT_HM 0xe5 + +/** + * struct sht21 - SHT21 device specific data + * @hwmon_dev: device registered with hwmon + * @lock: mutex to protect measurement values + * @valid: only 0 before first measurement is taken + * @last_update: time of last update (jiffies) + * @temperature: cached temperature measurement value + * @humidity: cached humidity measurement value + */ +struct sht21 { + struct device *hwmon_dev; + struct mutex lock; + char valid; + unsigned long last_update; + int temperature; + int humidity; +}; + +/** + * sht21_temp_ticks_to_millicelsius() - convert raw temperature ticks to + * milli celsius + * @ticks: temperature ticks value received from sensor + */ +static inline int sht21_temp_ticks_to_millicelsius(int ticks) +{ + ticks &= ~0x0003; /* clear status bits */ + /* + * Formula T = -46.85 + 175.72 * ST / 2^16 from data sheet 6.2, + * optimized for integer fixed point (3 digits) arithmetic + */ + return ((21965 * ticks) >> 13) - 46850; +} + +/** + * sht21_rh_ticks_to_per_cent_mille() - convert raw humidity ticks to + * one-thousandths of a percent relative humidity + * @ticks: humidity ticks value received from sensor + */ +static inline int sht21_rh_ticks_to_per_cent_mille(int ticks) +{ + ticks &= ~0x0003; /* clear status bits */ + /* + * Formula RH = -6 + 125 * SRH / 2^16 from data sheet 6.1, + * optimized for integer fixed point (3 digits) arithmetic + */ + return ((15625 * ticks) >> 13) - 6000; +} + +/** + * sht21_read_word_data() - read word from register + * @client: I2C client device + * @reg: I2C command byte + * + * Returns value, negative errno on error. + */ +static inline int sht21_read_word_data(struct i2c_client *client, u8 reg) +{ + int ret = i2c_smbus_read_word_data(client, reg); + if (ret < 0) + return ret; + /* + * SMBus specifies low byte first, but the SHT21 returns MSB + * first, so we have to swab16 the values + */ + return swab16(ret); +} + +/** + * sht21_update_measurements() - get updated measurements from device + * @client: I2C client device + * + * Returns 0 on success, else negative errno. + */ +static int sht21_update_measurements(struct i2c_client *client) +{ + int ret = 0; + struct sht21 *sht21 = i2c_get_clientdata(client); + + mutex_lock(&sht21->lock); + /* + * Data sheet 2.4: + * SHT2x should not be active for more than 10% of the time - e.g. + * maximum two measurements per second at 12bit accuracy shall be made. + */ + if (time_after(jiffies, sht21->last_update + HZ / 2) || !sht21->valid) { + ret = sht21_read_word_data(client, SHT21_TRIG_T_MEASUREMENT_HM); + if (ret < 0) + goto out; + sht21->temperature = sht21_temp_ticks_to_millicelsius(ret); + ret = sht21_read_word_data(client, + SHT21_TRIG_RH_MEASUREMENT_HM); + if (ret < 0) + goto out; + sht21->humidity = sht21_rh_ticks_to_per_cent_mille(ret); + sht21->last_update = jiffies; + sht21->valid = 1; + } +out: + mutex_unlock(&sht21->lock); + + return ret >= 0 ? 0 : ret; +} + +/** + * sht21_show_temperature() - show temperature measurement value in sysfs + * @dev: device + * @attr: device attribute + * @buf: sysfs buffer (PAGE_SIZE) where measurement values are written to + * + * Will be called on read access to temp1_input sysfs attribute. + * Returns number of bytes written into buffer, negative errno on error. + */ +static ssize_t sht21_show_temperature(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct sht21 *sht21 = i2c_get_clientdata(client); + int ret = sht21_update_measurements(client); + if (ret < 0) + return ret; + return sprintf(buf, "%d\n", sht21->temperature); +} + +/** + * sht21_show_humidity() - show humidity measurement value in sysfs + * @dev: device + * @attr: device attribute + * @buf: sysfs buffer (PAGE_SIZE) where measurement values are written to + * + * Will be called on read access to humidity1_input sysfs attribute. + * Returns number of bytes written into buffer, negative errno on error. + */ +static ssize_t sht21_show_humidity(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct i2c_client *client = to_i2c_client(dev); + struct sht21 *sht21 = i2c_get_clientdata(client); + int ret = sht21_update_measurements(client); + if (ret < 0) + return ret; + return sprintf(buf, "%d\n", sht21->humidity); +} + +/* sysfs attributes */ +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, sht21_show_temperature, + NULL, 0); +static SENSOR_DEVICE_ATTR(humidity1_input, S_IRUGO, sht21_show_humidity, + NULL, 0); + +static struct attribute *sht21_attributes[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_humidity1_input.dev_attr.attr, + NULL +}; + +static const struct attribute_group sht21_attr_group = { + .attrs = sht21_attributes, +}; + +/** + * sht21_probe() - probe device + * @client: I2C client device + * @id: device ID + * + * Called by the I2C core when an entry in the ID table matches a + * device's name. + * Returns 0 on success. + */ +static int __devinit sht21_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct sht21 *sht21; + int err; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_WORD_DATA)) { + dev_err(&client->dev, + "adapter does not support SMBus word transactions\n"); + return -ENODEV; + } + + sht21 = kzalloc(sizeof(*sht21), GFP_KERNEL); + if (!sht21) { + dev_dbg(&client->dev, "kzalloc failed\n"); + return -ENOMEM; + } + i2c_set_clientdata(client, sht21); + + mutex_init(&sht21->lock); + + err = sysfs_create_group(&client->dev.kobj, &sht21_attr_group); + if (err) { + dev_dbg(&client->dev, "could not create sysfs files\n"); + goto fail_free; + } + sht21->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(sht21->hwmon_dev)) { + dev_dbg(&client->dev, "unable to register hwmon device\n"); + err = PTR_ERR(sht21->hwmon_dev); + goto fail_remove_sysfs; + } + + dev_info(&client->dev, "initialized\n"); + + return 0; + +fail_remove_sysfs: + sysfs_remove_group(&client->dev.kobj, &sht21_attr_group); +fail_free: + kfree(sht21); + + return err; +} + +/** + * sht21_remove() - remove device + * @client: I2C client device + */ +static int __devexit sht21_remove(struct i2c_client *client) +{ + struct sht21 *sht21 = i2c_get_clientdata(client); + + hwmon_device_unregister(sht21->hwmon_dev); + sysfs_remove_group(&client->dev.kobj, &sht21_attr_group); + kfree(sht21); + + return 0; +} + +/* Device ID table */ +static const struct i2c_device_id sht21_id[] = { + { "sht21", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, sht21_id); + +static struct i2c_driver sht21_driver = { + .driver.name = "sht21", + .probe = sht21_probe, + .remove = __devexit_p(sht21_remove), + .id_table = sht21_id, +}; + +/** + * sht21_init() - initialize driver + * + * Called when kernel is booted or module is inserted. + * Returns 0 on success. + */ +static int __init sht21_init(void) +{ + return i2c_add_driver(&sht21_driver); +} +module_init(sht21_init); + +/** + * sht21_init() - clean up driver + * + * Called when module is removed. + */ +static void __exit sht21_exit(void) +{ + i2c_del_driver(&sht21_driver); +} +module_exit(sht21_exit); + +MODULE_AUTHOR("Urs Fleisch "); +MODULE_DESCRIPTION("Sensirion SHT21 humidity and temperature sensor driver"); +MODULE_LICENSE("GPL"); -- 2.34.1