From 9df7305b5a8651eb940e98496bc1d4742379c578 Mon Sep 17 00:00:00 2001 From: Steve Glendinning Date: Sat, 14 Aug 2010 21:08:54 +0200 Subject: [PATCH] hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller SMSC's EMC2103 family of temperature/fan controllers have 1 onboard and up to 3 external temperature sensors, and allow closed-loop control of one fan. This patch adds support for them. Signed-off-by: Steve Glendinning Signed-off-by: Jean Delvare --- Documentation/hwmon/emc2103 | 33 ++ MAINTAINERS | 7 + drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/emc2103.c | 740 ++++++++++++++++++++++++++++++++++++ 5 files changed, 791 insertions(+) create mode 100644 Documentation/hwmon/emc2103 create mode 100644 drivers/hwmon/emc2103.c diff --git a/Documentation/hwmon/emc2103 b/Documentation/hwmon/emc2103 new file mode 100644 index 000000000000..a12b2c127140 --- /dev/null +++ b/Documentation/hwmon/emc2103 @@ -0,0 +1,33 @@ +Kernel driver emc2103 +====================== + +Supported chips: + * SMSC EMC2103 + Addresses scanned: I2C 0x2e + Prefix: 'emc2103' + Datasheet: Not public + +Authors: + Steve Glendinning + +Description +----------- + +The Standard Microsystems Corporation (SMSC) EMC2103 chips +contain up to 4 temperature sensors and a single fan controller. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. Fan +readings can be divided by a programmable divider (1, 2, 4 or 8) to give +the readings more range or accuracy. Not all RPM values can accurately be +represented, so some rounding is done. With a divider of 1, the lowest +representable value is 480 RPM. + +This driver supports RPM based control, to use this a fan target +should be written to fan1_target and pwm1_enable should be set to 3. + +The 2103-2 and 2103-4 variants have a third temperature sensor, which can +be connected to two anti-parallel diodes. These values can be read +as temp3 and temp4. If only one diode is attached to this channel, temp4 +will show as "fault". The module parameter "apd=0" can be used to suppress +this 4th channel when anti-parallel diodes are not fitted. diff --git a/MAINTAINERS b/MAINTAINERS index 39d8c5ce9913..67fe8b1d8847 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -5279,6 +5279,13 @@ S: Maintained F: Documentation/hwmon/smm665 F: drivers/hwmon/smm665.c +SMSC EMC2103 HARDWARE MONITOR DRIVER +M: Steve Glendinning +L: lm-sensors@lm-sensors.org +S: Supported +F: Documentation/hwmon/emc2103 +F: drivers/hwmon/emc2103.c + SMSC47B397 HARDWARE MONITOR DRIVER M: "Mark M. Hoffman" L: lm-sensors@lm-sensors.org diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index f3adf18bfa05..d50e9fa8016f 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -804,6 +804,16 @@ config SENSORS_EMC1403 Threshold values can be configured using sysfs. Data from the different diodes are accessible via sysfs. +config SENSORS_EMC2103 + tristate "SMSC EMC2103" + depends on I2C + help + If you say yes here you get support for the temperature + and fan sensors of the SMSC EMC2103 chips. + + This driver can also be built as a module. If so, the module + will be called emc2103. + config SENSORS_SMSC47M1 tristate "SMSC LPC47M10x and compatibles" help diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 13d913e34dbf..e3c2484f6c5f 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -43,6 +43,7 @@ obj-$(CONFIG_SENSORS_PKGTEMP) += pkgtemp.o obj-$(CONFIG_SENSORS_DME1737) += dme1737.o obj-$(CONFIG_SENSORS_DS1621) += ds1621.o obj-$(CONFIG_SENSORS_EMC1403) += emc1403.o +obj-$(CONFIG_SENSORS_EMC2103) += emc2103.o obj-$(CONFIG_SENSORS_F71805F) += f71805f.o obj-$(CONFIG_SENSORS_F71882FG) += f71882fg.o obj-$(CONFIG_SENSORS_F75375S) += f75375s.o diff --git a/drivers/hwmon/emc2103.c b/drivers/hwmon/emc2103.c new file mode 100644 index 000000000000..af914ad93ece --- /dev/null +++ b/drivers/hwmon/emc2103.c @@ -0,0 +1,740 @@ +/* + emc2103.c - Support for SMSC EMC2103 + Copyright (c) 2010 SMSC + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* Addresses scanned */ +static const unsigned short normal_i2c[] = { 0x2E, I2C_CLIENT_END }; + +static const u8 REG_TEMP[4] = { 0x00, 0x02, 0x04, 0x06 }; +static const u8 REG_TEMP_MIN[4] = { 0x3c, 0x38, 0x39, 0x3a }; +static const u8 REG_TEMP_MAX[4] = { 0x34, 0x30, 0x31, 0x32 }; + +#define REG_CONF1 0x20 +#define REG_TEMP_MAX_ALARM 0x24 +#define REG_TEMP_MIN_ALARM 0x25 +#define REG_FAN_CONF1 0x42 +#define REG_FAN_TARGET_LO 0x4c +#define REG_FAN_TARGET_HI 0x4d +#define REG_FAN_TACH_HI 0x4e +#define REG_FAN_TACH_LO 0x4f +#define REG_PRODUCT_ID 0xfd +#define REG_MFG_ID 0xfe + +/* equation 4 from datasheet: rpm = (3932160 * multipler) / count */ +#define FAN_RPM_FACTOR 3932160 + +/* 2103-2 and 2103-4's 3rd temperature sensor can be connected to two diodes + * in anti-parallel mode, and in this configuration both can be read + * independently (so we have 4 temperature inputs). The device can't + * detect if it's connected in this mode, so we have to manually enable + * it. Default is to leave the device in the state it's already in (-1). + * This parameter allows APD mode to be optionally forced on or off */ +static int apd = -1; +module_param(apd, bool, 0); +MODULE_PARM_DESC(init, "Set to zero to disable anti-parallel diode mode"); + +struct temperature { + s8 degrees; + u8 fraction; /* 0-7 multiples of 0.125 */ +}; + +struct emc2103_data { + struct device *hwmon_dev; + struct mutex update_lock; + bool valid; /* registers are valid */ + bool fan_rpm_control; + int temp_count; /* num of temp sensors */ + unsigned long last_updated; /* in jiffies */ + struct temperature temp[4]; /* internal + 3 external */ + s8 temp_min[4]; /* no fractional part */ + s8 temp_max[4]; /* no fractional part */ + u8 temp_min_alarm; + u8 temp_max_alarm; + u8 fan_multiplier; + u16 fan_tach; + u16 fan_target; +}; + +static int read_u8_from_i2c(struct i2c_client *client, u8 i2c_reg, u8 *output) +{ + int status = i2c_smbus_read_byte_data(client, i2c_reg); + if (status < 0) { + dev_warn(&client->dev, "reg 0x%02x, err %d\n", + i2c_reg, status); + } else { + *output = status; + } + return status; +} + +static void read_temp_from_i2c(struct i2c_client *client, u8 i2c_reg, + struct temperature *temp) +{ + u8 degrees, fractional; + + if (read_u8_from_i2c(client, i2c_reg, °rees) < 0) + return; + + if (read_u8_from_i2c(client, i2c_reg + 1, &fractional) < 0) + return; + + temp->degrees = degrees; + temp->fraction = (fractional & 0xe0) >> 5; +} + +static void read_fan_from_i2c(struct i2c_client *client, u16 *output, + u8 hi_addr, u8 lo_addr) +{ + u8 high_byte, lo_byte; + + if (read_u8_from_i2c(client, hi_addr, &high_byte) < 0) + return; + + if (read_u8_from_i2c(client, lo_addr, &lo_byte) < 0) + return; + + *output = ((u16)high_byte << 5) | (lo_byte >> 3); +} + +static void write_fan_target_to_i2c(struct i2c_client *client, u16 new_target) +{ + u8 high_byte = (new_target & 0x1fe0) >> 5; + u8 low_byte = (new_target & 0x001f) << 3; + i2c_smbus_write_byte_data(client, REG_FAN_TARGET_LO, low_byte); + i2c_smbus_write_byte_data(client, REG_FAN_TARGET_HI, high_byte); +} + +static void read_fan_config_from_i2c(struct i2c_client *client) + +{ + struct emc2103_data *data = i2c_get_clientdata(client); + u8 conf1; + + if (read_u8_from_i2c(client, REG_FAN_CONF1, &conf1) < 0) + return; + + data->fan_multiplier = 1 << ((conf1 & 0x60) >> 5); + data->fan_rpm_control = (conf1 & 0x80) != 0; +} + +static struct emc2103_data *emc2103_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct emc2103_data *data = i2c_get_clientdata(client); + + mutex_lock(&data->update_lock); + + if (time_after(jiffies, data->last_updated + HZ + HZ / 2) + || !data->valid) { + int i; + + for (i = 0; i < data->temp_count; i++) { + read_temp_from_i2c(client, REG_TEMP[i], &data->temp[i]); + read_u8_from_i2c(client, REG_TEMP_MIN[i], + &data->temp_min[i]); + read_u8_from_i2c(client, REG_TEMP_MAX[i], + &data->temp_max[i]); + } + + read_u8_from_i2c(client, REG_TEMP_MIN_ALARM, + &data->temp_min_alarm); + read_u8_from_i2c(client, REG_TEMP_MAX_ALARM, + &data->temp_max_alarm); + + read_fan_from_i2c(client, &data->fan_tach, + REG_FAN_TACH_HI, REG_FAN_TACH_LO); + read_fan_from_i2c(client, &data->fan_target, + REG_FAN_TARGET_HI, REG_FAN_TARGET_LO); + read_fan_config_from_i2c(client); + + data->last_updated = jiffies; + data->valid = true; + } + + mutex_unlock(&data->update_lock); + + return data; +} + +static ssize_t +show_temp(struct device *dev, struct device_attribute *da, char *buf) +{ + int nr = to_sensor_dev_attr(da)->index; + struct emc2103_data *data = emc2103_update_device(dev); + int millidegrees = data->temp[nr].degrees * 1000 + + data->temp[nr].fraction * 125; + return sprintf(buf, "%d\n", millidegrees); +} + +static ssize_t +show_temp_min(struct device *dev, struct device_attribute *da, char *buf) +{ + int nr = to_sensor_dev_attr(da)->index; + struct emc2103_data *data = emc2103_update_device(dev); + int millidegrees = data->temp_min[nr] * 1000; + return sprintf(buf, "%d\n", millidegrees); +} + +static ssize_t +show_temp_max(struct device *dev, struct device_attribute *da, char *buf) +{ + int nr = to_sensor_dev_attr(da)->index; + struct emc2103_data *data = emc2103_update_device(dev); + int millidegrees = data->temp_max[nr] * 1000; + return sprintf(buf, "%d\n", millidegrees); +} + +static ssize_t +show_temp_fault(struct device *dev, struct device_attribute *da, char *buf) +{ + int nr = to_sensor_dev_attr(da)->index; + struct emc2103_data *data = emc2103_update_device(dev); + bool fault = (data->temp[nr].degrees == -128); + return sprintf(buf, "%d\n", fault ? 1 : 0); +} + +static ssize_t +show_temp_min_alarm(struct device *dev, struct device_attribute *da, char *buf) +{ + int nr = to_sensor_dev_attr(da)->index; + struct emc2103_data *data = emc2103_update_device(dev); + bool alarm = data->temp_min_alarm & (1 << nr); + return sprintf(buf, "%d\n", alarm ? 1 : 0); +} + +static ssize_t +show_temp_max_alarm(struct device *dev, struct device_attribute *da, char *buf) +{ + int nr = to_sensor_dev_attr(da)->index; + struct emc2103_data *data = emc2103_update_device(dev); + bool alarm = data->temp_max_alarm & (1 << nr); + return sprintf(buf, "%d\n", alarm ? 1 : 0); +} + +static ssize_t set_temp_min(struct device *dev, struct device_attribute *da, + const char *buf, size_t count) +{ + int nr = to_sensor_dev_attr(da)->index; + struct i2c_client *client = to_i2c_client(dev); + struct emc2103_data *data = i2c_get_clientdata(client); + long val; + + int result = strict_strtol(buf, 10, &val); + if (result < 0) + return -EINVAL; + + val = DIV_ROUND_CLOSEST(val, 1000); + if ((val < -63) || (val > 127)) + return -EINVAL; + + mutex_lock(&data->update_lock); + data->temp_min[nr] = val; + i2c_smbus_write_byte_data(client, REG_TEMP_MIN[nr], val); + mutex_unlock(&data->update_lock); + + return count; +} + +static ssize_t set_temp_max(struct device *dev, struct device_attribute *da, + const char *buf, size_t count) +{ + int nr = to_sensor_dev_attr(da)->index; + struct i2c_client *client = to_i2c_client(dev); + struct emc2103_data *data = i2c_get_clientdata(client); + long val; + + int result = strict_strtol(buf, 10, &val); + if (result < 0) + return -EINVAL; + + val = DIV_ROUND_CLOSEST(val, 1000); + if ((val < -63) || (val > 127)) + return -EINVAL; + + mutex_lock(&data->update_lock); + data->temp_max[nr] = val; + i2c_smbus_write_byte_data(client, REG_TEMP_MAX[nr], val); + mutex_unlock(&data->update_lock); + + return count; +} + +static ssize_t +show_fan(struct device *dev, struct device_attribute *da, char *buf) +{ + struct emc2103_data *data = emc2103_update_device(dev); + int rpm = 0; + if (data->fan_tach != 0) + rpm = (FAN_RPM_FACTOR * data->fan_multiplier) / data->fan_tach; + return sprintf(buf, "%d\n", rpm); +} + +static ssize_t +show_fan_div(struct device *dev, struct device_attribute *da, char *buf) +{ + struct emc2103_data *data = emc2103_update_device(dev); + int fan_div = 8 / data->fan_multiplier; + return sprintf(buf, "%d\n", fan_div); +} + +/* Note: we also update the fan target here, because its value is + determined in part by the fan clock divider. This follows the principle + of least surprise; the user doesn't expect the fan target to change just + because the divider changed. */ +static ssize_t set_fan_div(struct device *dev, struct device_attribute *da, + const char *buf, size_t count) +{ + struct emc2103_data *data = emc2103_update_device(dev); + struct i2c_client *client = to_i2c_client(dev); + int new_range_bits, old_div = 8 / data->fan_multiplier; + long new_div; + + int status = strict_strtol(buf, 10, &new_div); + if (status < 0) + return -EINVAL; + + if (new_div == old_div) /* No change */ + return count; + + switch (new_div) { + case 1: + new_range_bits = 3; + break; + case 2: + new_range_bits = 2; + break; + case 4: + new_range_bits = 1; + break; + case 8: + new_range_bits = 0; + break; + default: + return -EINVAL; + } + + mutex_lock(&data->update_lock); + + status = i2c_smbus_read_byte_data(client, REG_FAN_CONF1); + if (status < 0) { + dev_dbg(&client->dev, "reg 0x%02x, err %d\n", + REG_FAN_CONF1, status); + mutex_unlock(&data->update_lock); + return -EIO; + } + status &= 0x9F; + status |= (new_range_bits << 5); + i2c_smbus_write_byte_data(client, REG_FAN_CONF1, status); + + data->fan_multiplier = 8 / new_div; + + /* update fan target if high byte is not disabled */ + if ((data->fan_target & 0x1fe0) != 0x1fe0) { + u16 new_target = (data->fan_target * old_div) / new_div; + data->fan_target = min(new_target, (u16)0x1fff); + write_fan_target_to_i2c(client, data->fan_target); + } + + /* invalidate data to force re-read from hardware */ + data->valid = false; + + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t +show_fan_target(struct device *dev, struct device_attribute *da, char *buf) +{ + struct emc2103_data *data = emc2103_update_device(dev); + int rpm = 0; + + /* high byte of 0xff indicates disabled so return 0 */ + if ((data->fan_target != 0) && ((data->fan_target & 0x1fe0) != 0x1fe0)) + rpm = (FAN_RPM_FACTOR * data->fan_multiplier) + / data->fan_target; + + return sprintf(buf, "%d\n", rpm); +} + +static ssize_t set_fan_target(struct device *dev, struct device_attribute *da, + const char *buf, size_t count) +{ + struct emc2103_data *data = emc2103_update_device(dev); + struct i2c_client *client = to_i2c_client(dev); + long rpm_target; + + int result = strict_strtol(buf, 10, &rpm_target); + if (result < 0) + return -EINVAL; + + /* Datasheet states 16384 as maximum RPM target (table 3.2) */ + if ((rpm_target < 0) || (rpm_target > 16384)) + return -EINVAL; + + mutex_lock(&data->update_lock); + + if (rpm_target == 0) + data->fan_target = 0x1fff; + else + data->fan_target = SENSORS_LIMIT( + (FAN_RPM_FACTOR * data->fan_multiplier) / rpm_target, + 0, 0x1fff); + + write_fan_target_to_i2c(client, data->fan_target); + + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t +show_fan_fault(struct device *dev, struct device_attribute *da, char *buf) +{ + struct emc2103_data *data = emc2103_update_device(dev); + bool fault = ((data->fan_tach & 0x1fe0) == 0x1fe0); + return sprintf(buf, "%d\n", fault ? 1 : 0); +} + +static ssize_t +show_pwm_enable(struct device *dev, struct device_attribute *da, char *buf) +{ + struct emc2103_data *data = emc2103_update_device(dev); + return sprintf(buf, "%d\n", data->fan_rpm_control ? 3 : 0); +} + +static ssize_t set_pwm_enable(struct device *dev, struct device_attribute *da, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct emc2103_data *data = i2c_get_clientdata(client); + long new_value; + u8 conf_reg; + + int result = strict_strtol(buf, 10, &new_value); + if (result < 0) + return -EINVAL; + + mutex_lock(&data->update_lock); + switch (new_value) { + case 0: + data->fan_rpm_control = false; + break; + case 3: + data->fan_rpm_control = true; + break; + default: + mutex_unlock(&data->update_lock); + return -EINVAL; + } + + read_u8_from_i2c(client, REG_FAN_CONF1, &conf_reg); + + if (data->fan_rpm_control) + conf_reg |= 0x80; + else + conf_reg &= ~0x80; + + i2c_smbus_write_byte_data(client, REG_FAN_CONF1, conf_reg); + + mutex_unlock(&data->update_lock); + return count; +} + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0); +static SENSOR_DEVICE_ATTR(temp1_min, S_IRUGO | S_IWUSR, show_temp_min, + set_temp_min, 0); +static SENSOR_DEVICE_ATTR(temp1_max, S_IRUGO | S_IWUSR, show_temp_max, + set_temp_max, 0); +static SENSOR_DEVICE_ATTR(temp1_fault, S_IRUGO, show_temp_fault, NULL, 0); +static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_temp_min_alarm, + NULL, 0); +static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_temp_max_alarm, + NULL, 0); + +static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1); +static SENSOR_DEVICE_ATTR(temp2_min, S_IRUGO | S_IWUSR, show_temp_min, + set_temp_min, 1); +static SENSOR_DEVICE_ATTR(temp2_max, S_IRUGO | S_IWUSR, show_temp_max, + set_temp_max, 1); +static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_temp_fault, NULL, 1); +static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_temp_min_alarm, + NULL, 1); +static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_temp_max_alarm, + NULL, 1); + +static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2); +static SENSOR_DEVICE_ATTR(temp3_min, S_IRUGO | S_IWUSR, show_temp_min, + set_temp_min, 2); +static SENSOR_DEVICE_ATTR(temp3_max, S_IRUGO | S_IWUSR, show_temp_max, + set_temp_max, 2); +static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_temp_fault, NULL, 2); +static SENSOR_DEVICE_ATTR(temp3_min_alarm, S_IRUGO, show_temp_min_alarm, + NULL, 2); +static SENSOR_DEVICE_ATTR(temp3_max_alarm, S_IRUGO, show_temp_max_alarm, + NULL, 2); + +static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, show_temp, NULL, 3); +static SENSOR_DEVICE_ATTR(temp4_min, S_IRUGO | S_IWUSR, show_temp_min, + set_temp_min, 3); +static SENSOR_DEVICE_ATTR(temp4_max, S_IRUGO | S_IWUSR, show_temp_max, + set_temp_max, 3); +static SENSOR_DEVICE_ATTR(temp4_fault, S_IRUGO, show_temp_fault, NULL, 3); +static SENSOR_DEVICE_ATTR(temp4_min_alarm, S_IRUGO, show_temp_min_alarm, + NULL, 3); +static SENSOR_DEVICE_ATTR(temp4_max_alarm, S_IRUGO, show_temp_max_alarm, + NULL, 3); + +static DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL); +static DEVICE_ATTR(fan1_div, S_IRUGO | S_IWUSR, show_fan_div, set_fan_div); +static DEVICE_ATTR(fan1_target, S_IRUGO | S_IWUSR, show_fan_target, + set_fan_target); +static DEVICE_ATTR(fan1_fault, S_IRUGO, show_fan_fault, NULL); + +static DEVICE_ATTR(pwm1_enable, S_IRUGO | S_IWUSR, show_pwm_enable, + set_pwm_enable); + +/* sensors present on all models */ +static struct attribute *emc2103_attributes[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp1_fault.dev_attr.attr, + &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_input.dev_attr.attr, + &sensor_dev_attr_temp2_min.dev_attr.attr, + &sensor_dev_attr_temp2_max.dev_attr.attr, + &sensor_dev_attr_temp2_fault.dev_attr.attr, + &sensor_dev_attr_temp2_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp2_max_alarm.dev_attr.attr, + &dev_attr_fan1_input.attr, + &dev_attr_fan1_div.attr, + &dev_attr_fan1_target.attr, + &dev_attr_fan1_fault.attr, + &dev_attr_pwm1_enable.attr, + NULL +}; + +/* extra temperature sensors only present on 2103-2 and 2103-4 */ +static struct attribute *emc2103_attributes_temp3[] = { + &sensor_dev_attr_temp3_input.dev_attr.attr, + &sensor_dev_attr_temp3_min.dev_attr.attr, + &sensor_dev_attr_temp3_max.dev_attr.attr, + &sensor_dev_attr_temp3_fault.dev_attr.attr, + &sensor_dev_attr_temp3_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp3_max_alarm.dev_attr.attr, + NULL +}; + +/* extra temperature sensors only present on 2103-2 and 2103-4 in APD mode */ +static struct attribute *emc2103_attributes_temp4[] = { + &sensor_dev_attr_temp4_input.dev_attr.attr, + &sensor_dev_attr_temp4_min.dev_attr.attr, + &sensor_dev_attr_temp4_max.dev_attr.attr, + &sensor_dev_attr_temp4_fault.dev_attr.attr, + &sensor_dev_attr_temp4_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp4_max_alarm.dev_attr.attr, + NULL +}; + +static const struct attribute_group emc2103_group = { + .attrs = emc2103_attributes, +}; + +static const struct attribute_group emc2103_temp3_group = { + .attrs = emc2103_attributes_temp3, +}; + +static const struct attribute_group emc2103_temp4_group = { + .attrs = emc2103_attributes_temp4, +}; + +static int +emc2103_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + struct emc2103_data *data; + int status; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -EIO; + + data = kzalloc(sizeof(struct emc2103_data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + + /* 2103-2 and 2103-4 have 3 external diodes, 2103-1 has 1 */ + status = i2c_smbus_read_byte_data(client, REG_PRODUCT_ID); + if (status == 0x24) { + /* 2103-1 only has 1 external diode */ + data->temp_count = 2; + } else { + /* 2103-2 and 2103-4 have 3 or 4 external diodes */ + status = i2c_smbus_read_byte_data(client, REG_CONF1); + if (status < 0) { + dev_dbg(&client->dev, "reg 0x%02x, err %d\n", REG_CONF1, + status); + goto exit_free; + } + + /* detect current state of hardware */ + data->temp_count = (status & 0x01) ? 4 : 3; + + /* force APD state if module parameter is set */ + if (apd == 0) { + /* force APD mode off */ + data->temp_count = 3; + status &= ~(0x01); + i2c_smbus_write_byte_data(client, REG_CONF1, status); + } else if (apd == 1) { + /* force APD mode on */ + data->temp_count = 4; + status |= 0x01; + i2c_smbus_write_byte_data(client, REG_CONF1, status); + } + } + + /* Register sysfs hooks */ + status = sysfs_create_group(&client->dev.kobj, &emc2103_group); + if (status) + goto exit_free; + + if (data->temp_count >= 3) { + status = sysfs_create_group(&client->dev.kobj, + &emc2103_temp3_group); + if (status) + goto exit_remove; + } + + if (data->temp_count == 4) { + status = sysfs_create_group(&client->dev.kobj, + &emc2103_temp4_group); + if (status) + goto exit_remove_temp3; + } + + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + status = PTR_ERR(data->hwmon_dev); + goto exit_remove_temp4; + } + + dev_info(&client->dev, "%s: sensor '%s'\n", + dev_name(data->hwmon_dev), client->name); + + return 0; + +exit_remove_temp4: + if (data->temp_count == 4) + sysfs_remove_group(&client->dev.kobj, &emc2103_temp4_group); +exit_remove_temp3: + if (data->temp_count >= 3) + sysfs_remove_group(&client->dev.kobj, &emc2103_temp3_group); +exit_remove: + sysfs_remove_group(&client->dev.kobj, &emc2103_group); +exit_free: + kfree(data); + return status; +} + +static int emc2103_remove(struct i2c_client *client) +{ + struct emc2103_data *data = i2c_get_clientdata(client); + + hwmon_device_unregister(data->hwmon_dev); + + if (data->temp_count == 4) + sysfs_remove_group(&client->dev.kobj, &emc2103_temp4_group); + + if (data->temp_count >= 3) + sysfs_remove_group(&client->dev.kobj, &emc2103_temp3_group); + + sysfs_remove_group(&client->dev.kobj, &emc2103_group); + + kfree(data); + return 0; +} + +static const struct i2c_device_id emc2103_ids[] = { + { "emc2103", 0, }, + { /* LIST END */ } +}; +MODULE_DEVICE_TABLE(i2c, emc2103_ids); + +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int +emc2103_detect(struct i2c_client *new_client, struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = new_client->adapter; + int manufacturer, product; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + manufacturer = i2c_smbus_read_byte_data(new_client, REG_MFG_ID); + if (manufacturer != 0x5D) + return -ENODEV; + + product = i2c_smbus_read_byte_data(new_client, REG_PRODUCT_ID); + if ((product != 0x24) && (product != 0x26)) + return -ENODEV; + + strlcpy(info->type, "emc2103", I2C_NAME_SIZE); + + return 0; +} + +static struct i2c_driver emc2103_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "emc2103", + }, + .probe = emc2103_probe, + .remove = emc2103_remove, + .id_table = emc2103_ids, + .detect = emc2103_detect, + .address_list = normal_i2c, +}; + +static int __init sensors_emc2103_init(void) +{ + return i2c_add_driver(&emc2103_driver); +} + +static void __exit sensors_emc2103_exit(void) +{ + i2c_del_driver(&emc2103_driver); +} + +MODULE_AUTHOR("Steve Glendinning "); +MODULE_DESCRIPTION("SMSC EMC2103 hwmon driver"); +MODULE_LICENSE("GPL"); + +module_init(sensors_emc2103_init); +module_exit(sensors_emc2103_exit); -- 2.34.1